Owner manual

CS61584A
32 DS261PP5
DS261PP5
10.1 JTAG Data Registers (DR)
The test data registers are the Boundary-Scan Reg-
ister (BSR), the Device Identification Register
(DIR), and the Bypass Register (BR).
Boundary Scan Register: The BSR is connected in
parallel to all the digital I/O pins, and provides the
mechanism for applying/reading test patterns
to/from the board traces. The BSR is 62 bits long
and is initialized and read using the instruction
SAMPLE/PRELOAD. The bit ordering for the
BSR is the same as the top-view package pin out,
beginning with the LOS1 pin and moving counter-
clockwise to end with the PD1 pin as shown in Ta-
ble 10. Note that the analog, oscillator, power,
ground, CLKE/IPOL, and MODE pins are not in-
cluded as part of the boundary-scan register.
The input pins require one bit in the BSR and only
one J-TCK cycle is required to load test data for
each input pin.
The output pins have two bits in the BSR to define
output high, output low, or high impedance. The
first bit (shifted in first) selects between an output-
enabled state (bit set to 1) or high-impedance state
(bit set to 0). The second bit shifted in contains the
test data that may be output on the pin. Therefore,
two J-TCK cycles are required to load test data for
each output pin.
The bi-directional pins have three bits in the BSR
to define input, output high, output low, or high im-
pedance. The first bit shifted into the BSR config-
ures the output driver as high-impedance (bit set to
0) or active (bit set to 1). The second bit shifted into
the BSR sets the output value when the first bit is 1.
The third bit captures the value of the pin. This pin
may have its value set externally as an input (if the
first bit is 0) or set internally as an output (if the
first bit is 1). To configure a pad as an input, the J-
TDI pattern is 0X0. To configure a pad as an out-
put, the J-TDI pattern is 1X1. Therefore, three J-
TCK cycles are required to load test data for each
bi-directional pin.
When JTAG testing is conducted in Host mode, the
polarity of the INT
pin is determined by the state of
the IPOL pin. The JTAG BSR should configure the
INT pin as an input in Hardware mode and as an
output in Host mode.
Device Identification Register: The DIR provides
the manufacturer, part number, and version of the
CS61584A. This information can be used to verify
that the proper version or revision number has been
used in the system under test. The DIR is 32 bits
long and is partitioned as shown in Table 11. Data
from the DIR is shifted out to J-TDO LSB first.
BSR Bits Pin Name Pad Type
0 - 2 LOS1, SAD6 bi-directional
3 - 5 TNEG1, AIS1 bi-directional
6 TPOS1, TDATA1 input
7TCLK1input
8 - 9 RNEG1, BPV1 output
10 - 11 RPOS1, RDATA1 output
12 - 13 RCLK1 output
14 ATTEN1, CS
input
15 - 17 RLOOP1, INT
bi-directional
18 RLOOP2, SCLK, RD
(DS) input
19 - 21 LLOOP, SDO, AD0 bi-directional
22 - 24 TAOS1, SDI, AD1 bi-directional
25 - 27 TAOS2, SPOL, AD2 bi-directional
28 - 30 CON01, AD3 bi-directional
31 - 33 CON02, AD4 bi-directional
34 - 36 CON11, AD5 bi-directional
37 - 39 CON12, AD6 bi-directional
40 - 42 CON21, AD7 bi-directional
43 CON22, ALE(AS) input
44 CON31, WR
(R/W) input
45 - 46 RCLK2 output
47 - 48 RPOS2, RDATA2 output
49 - 50 RNEG2, BPV2 output
51 TCLK2 input
52 TPOS2, TDATA2 input
53 - 55 TNEG2, AIS2 bi-directional
56 - 58 LOS2, SAD7 bi-directional
59 CON32, BTS input
60 PD2, SAD5 input
61 PD1, SAD4 input
Table 10. Boundary Scan Register
CS61584A
32 DS261F1