Manualshelf

User guide

ManualsBrandsCirrus Logic ManualsHardwareCS4353
12345678910
DS803F3 7
CS4353
DAC ANALOG CHARACTERISTICS
Test conditions (unless otherwise specified): T
A
= 25 °C; VCP = VA = 3.3 V; AOUT_REF = AGND = DGND =
CPGND = 0 V; VBIAS, VFILT+/-, and FLYP/N+/- capacitors as shown in Figure 3 on page 12; input test signal is a
997 Hz sine wave at 0 dBFS; measurement bandwidth 10 Hz to 20 kHz.
Notes: 2. Measured at the output of the external LPF on AOUTx as shown in Figure 3 on page 12.
3. One LSB of triangular PDF dither is added to data.
4. Measured with the specified minimum AC-Load Resistance present on the AOUTx pins.
5. Measured between the AOUTx and AOUT_REF pins.
6. External impedance between the AOUTx pin and the load will lower the voltage delivered to the load.
7. V
PP
is the controlling specification. V
RMS
specification valid for sine wave signals only.
Note that for sine wave signals:
8. Measured with AOUT_REF connected directly to ground. External impedance between AOUT_REF
and ground will lower the AOUT_REF rejection.
1_2VRMS = 0 1_2VRMS = 1
Parameter Symbol Min Typ Max Min Typ Max Unit
Dynamic Performance, Fs = 48, 96, and 192 kHz (Notes 2, 3, 4)
Dynamic Range 24-bit A-Weighted
unweighted
16-bit A-Weighted
unweighted
94
91
-
-
100
97
92
89
-
-
-
-
100
97
-
-
106
103
98
95
-
-
-
-
dB
dB
dB
dB
Total Harmonic Distortion + Noise
24-bit 0 dB
-20 dB
-60 dB
16-bit 0 dB
-20 dB
-60 dB
THD+N
-
-
-
-
-
-
-
-93
-77
-37
-93
-75
-29
-87
-71
-31
-
-
-
-
-
-
-
-
-
-
-93
-83
-43
-93
-75
-35
-87
-77
-37
-
-
-
dB
dB
dB
dB
dB
dB
Idle Channel Noise / Signal-to-Noise Ratio (A-wt) - 100 - - 106 - dB
Interchannel Isolation (1 kHz) - 115 - - 115 - dB
Analog Output (Note 5)
Full Scale AOUTx Output Voltage (Notes 4, 6, 7) 1.021.081.132.042.152.26V
RMS
2.89 3.05 3.20 5.78 6.09 6.40 V
pp
Max Current Draw from an AOUTx Pin I
OUTmax
-575- -575- A
Interchannel Gain Mismatch - 0.1 - - 0.1 - dB
Output Offset - ±5 ±8 - ±5 ±8 mV
Gain Drift - 100 - - 100 - ppm/°C
Output Impedance Z
OUT
-100- -100-
AC-Load Resistance R
L
5--5--k
Load Capacitance C
L
- - 1000 - - 1000 pF
AOUT_REF Rejection (Notes 8, 9)AOR-40- -40-dB
Analog Reference Input
AOUT_REF Input Voltage (Note 10) --0.2--0.2Vpp
VRMS
Vpp
22
----------=