Owner manual
12 DS963F4
CS35L32
3 Characteristics and Specifications
Table 3-9. PSRR Characteristics
Test conditions, except where noted otherwise: VA = 1.8 V, VP = 3.6 V, VBST = VP, amp gain = 12 dB, GNDA = GNDP = 0 V, T
A
= +25°C.
Parameters Conditions
Noise
Injected Into
Noise
Measured On
Noise
Amplitude (mV)
Noise
Frequency (Hz)
Min Typical Max Units
Speaker amplifier
PSRR
VBST = VP VA SPKOUT± 100 217
1k
20k
—
—
—
75
75
70
—
—
—
dB
dB
dB
VP SPKOUT± 100 217
1k
20k
—
—
—
70
70
55
—
—
—
dB
dB
dB
VPMON PSRR VBST = VP VA SDOUT 100 217
1k
20k
—
—
—
36
36
33
—
—
—
dB
dB
dB
VSENSE± PSRR
1
1.The speaker voltage monitor has a lower PSRR because its input path has an attenuation of 16.6 dB. The PSRR specification is referred to the input
signal and, as such, includes the loss of 16.6 dB.
VBST = VP VA SDOUT 100 217
1k
20k
—
—
—
60
60
50
—
—
—
dB
dB
dB
ISENSE± PSRR VBST = VP VA SDOUT 100 217
1k
20k
—
—
—
60
60
60
—
—
—
dB
dB
dB
Table 3-10. Power Consumption
Test conditions, except where noted otherwise: VA = 1.8 V, VP = 3.6 V, VBST = VP, GNDA = GNDP = 0 V, T
A
= +25°C.
Use Configuration
Typical Current
i
VP
i
VA
Units
Powered up
(
PDN_BST = 00)
RESET asserted, MCLK, SCLK, LRCK inactive
11A
IN+ IN– shorted to ground, LEDs off, monitors powered down
1
1.Refer to Section 7.6 for configuring monitor power down
No C
OUT
3270 390 A
IN+ IN– shorted to ground, LEDs off, monitors powered down
1
C
OUT
= 470 pF (See Fig. 2-1) 4275 390 A
IN+ IN– shorted to ground, LEDs off, monitors powered up
1
No C
OUT
3360 1435 A
IN+ IN– shorted to ground, LEDs off, monitors powered up
1
C
OUT
= 470 pF See Fig. 2-1) 4360 1435 A
Boost Mode
bypass
(
PDN_BST = 01)
.
RESET
asserted, MCLK, SCLK, LRCK inactive
11A
IN+ IN– shorted to ground, LEDs off, monitors powered down
1
No C
OUT
1983 390 A
IN+ IN– shorted to ground, LEDs off, monitors powered down
1
C
OUT
= 470 pF (See Fig. 2-1) 3093 390 A
IN+ IN– shorted to ground, LEDs off, monitors powered up
1
No C
OUT
2074 1435 A
IN+ IN– shorted to ground, LEDs off, monitors powered up
1
C
OUT
= 470 pF See Fig. 2-1) 3185 1435 A
Table 3-11. Switching Specifications: Power, Reset, Master Clocks
Test conditions, except where noted otherwise: VA = 1.8 V, VP = 3.6 V, VBST = 5.0 V, T
A
= +25°C, GNDA = GNDP = 0 V. Fig. 2-1 shows typical
connections; GNDA = GNDP = 0 V. Section 9 describes some parameters in detail; input timings are measured at V
IL
and V
IH
thresholds; output timings
are measured at V
OL
and V
OH
thresholds (see Table 3-8).
Parameters Symbol
1
1.Power and reset sequencing
Min Max Units
Power supplies
2
2.VP supply may be applied or removed independently of RESET and the other power rails. See Section 4.1 for additional details.
Power supply ramp up/down t
PWR-RUD
— 100 ms
Reset
2
RESET low (logic 0) pulse width
t
RLPW
1—ms
RESET
hold time after power supplies ramp up
t
RH(PWR-RH)
1—ms
RESET
setup time before power supplies ramp down
t
RS(RL-PWR)
1—ms
RESET
rising edge to control-port active
t
IRS
[3]
3.The RESET rising-edge-to-control-port-active timing, t
irs
, is specified in Table 3-13.
—ns
Master clocks MCLK frequency
4
4.Maximum frequency for highest supported nominal rate is indicated. The supported nominal serial port sample rates are found in Section 4.11.2.
f
MCLK
— 12.3 MHz
MCLK duty cycle D
MCLK
45 55 %
V
MIN
GND
Internal supplies stable
V
OPERATING
t
RH(PWR-RH)
t
IRS
Control port active
t
RS(RL-PWR)
RESET
t
PWR-RUD
t
PWR-RUD
t
PWR-
RUD
t
PWR-RUD
1
st
Supply
Up
Last
Supply
Up
1
st
Supply
Down
Last
Supply
Down