8000 Series Mobile Computer 8000/8001/8020/8021/8061/8062/8071 Version 2.
Copyright © 2006~ 2008 CIPHERLAB CO., LTD. All rights reserved The software contains proprietary information of CIPHERLAB CO., LTD.; it is provided under a license agreement containing restrictions on use and disclosure and is also protected by copyright law. Reverse engineering of the software is prohibited. Due to continued product development this information may change without notice.
IMPORTANT NOTICES FOR USA This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
FOR PRODUCT WITH LASER Per FDA and IEC standards, the scan engines described in this manual are not given a laser classification. However, the following precautions should be observed: CAUTION This laser component emits FDA / IEC Class 2 laser light at the exit port. Do not stare into beam. SAFETY PRECAUTIONS RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
RELEASE NOTES Version Date Notes 2.11 May 23, 2008 2.10 Apr. 24, 2008 New Word template applied 2.01 Aug. 10, 2007 2.00 Apr. 14, 2007 Modified: Specifications – Drop Test 1.2 meters Modified: section 1.5.
CONTENTS IMPORTANT NOTICES ........................................................................................................................... - 3 For USA .................................................................................................................................................- 3 For Canada...........................................................................................................................................- 3 For Hand-held Product with RF Functions........
000 Series Mobile Computer Reference Manual 1.8.3 IEEE 802.11b/g .................................................................................................................... 23 LEARNING SOFTWARE ARCHITECTURE ............................................................................................... 25 2.1 Application Module ....................................................................................................................... 27 2.1.1 Application Generator (AG)..................
8000 Series Mobile Computer Reference Manual 3.9.5 Pairing Test ........................................................................................................................... 53 3.9.6 Freq. Dev. List ....................................................................................................................... 54 3.9.7 Network Setting.................................................................................................................... 55 3.10 Wi-Fi Menu — 8071 ...........
INTRODUCTION Answering light industrial demands, the 8000 Series Mobile Computer is specifically designed for enterprise logistics use. Small-form-factor and light-weight, it proves to be an ace player in retail and healthcare applications. This line of product comes with optional Bluetooth and 802.11b/g wireless technologies, enabling real time sharing of performance.
8000 Series Mobile Computer Reference Manual GETTING FAMILIARIZED WITH 8000 2
錯誤! 尚未定義樣式。 Figure 1: Overview 3
8000 Series Mobile Computer Reference Manual CHARGING THE BATTERY You can use a cradle to charge the Mobile Computer, or the 4-Slot Battery Charger to charge up to four batteries. Below is the 4-Slot Battery Charger. For the Charging & Communication Cradle, refer to section 1.7 Communications via the Cradle. Warning: It is recommended that the charging devices be operated at room temperature (18°C to 25°C) for optimal performance.
錯誤! 尚未定義樣式。 DIMENSIONS Figure 3: Dimensions FEATURES Ergonomic design — small-form-factor with wrist strap for secure hold. Built light-weight to enhance mobility and ease data-intensive applications. Flexible wireless solution — IR/IrDA integrated, with connectivity options for Bluetooth, 802.11b/g or both. Acoustic Coupler for US market, ideal for replacement of older style terminals. Graphic monochrome LCD supports double-byte characters and bitmap graphics.
8000 Series Mobile Computer Reference Manual INSIDE THE PACKAGE In addition to the mobile computer, the following items are included in the package. Save the box and packaging material for future use in case you need to store or ship the mobile computer.
Chapter 1 USING 8000 MOBILE COMPUTER This chapter explains the features and usage of the 8000 Series Mobile Computer. The 8000 family includes: 8000 Batch type (powered by two AAA alkaline batteries) 8001 Batch type (powered by Li-ion battery) 8020 Acoustic Coupler (powered by two AAA alkaline batteries) 8021 Acoustic Coupler (powered by Li-ion battery) 8061 Bluetooth Class 1 (powered by Li-ion battery) 8062 Bluetooth Class 2 (powered by Li-ion battery) 8071 802.
8000 Series Mobile Computer Reference Manual Backup Battery The backup battery on the main board takes charge when the main battery is removed or drained out. When fully charged, the 3.0 V/7 mAh rechargeable Lithium button cell helps retain data in SRAM and maintain the running of the real-time clock and calendar for at least 30 days without the main battery. In the meantime, you have to replace the main battery as soon as possible. It takes at least twenty-four hours to fully charge the backup battery.
Chapter 1 錯誤! 尚未定義樣式。 1.1.2 CHARGING THE BATTERY The main and backup batteries may not be charged to full for shipment. When you first receive the package, you will need to charge batteries to full before using the mobile computer. Note: For initial charging, it takes approximately 2 hours to fully charge the main battery.
8000 Series Mobile Computer Reference Manual 1.2 MEMORY The collected data can be sent back to a host computer immediately over wireless networks, or stored in memory (SRAM) and upload later. The mobile computer is equipped with a calendar chip for accurate time/date logging. Read-only Memory (ROM) 2 megabytes flash memory for storing core, OS, application programs, fonts, etc. Random-access Memory (RAM) 2 megabytes SRAM for storing data. Its contents will be retained by the backup battery. 1.2.
Chapter 1 錯誤! 尚未定義樣式。 1.3 KEYPAD The mobile computer is equipped with a keypad of 21 keys for system setup, user entry and so on. The keypad comes with programmable LED backlight, like the screen. Refer to section 1.4 LCD for screen & backlight settings. Silicon rubber has been chosen for their durability and prompt feedback. The key click can be configured through programming or the System Menu. Below briefly describes the functions of common keys on the mobile computer.
8000 Series Mobile Computer Reference Manual 1.3.1 SCREEN ICONS When any of the following icons appears on the screen, it indicates a certain mode is activated. It means holding down the specific key is unnecessary. Screen Icon Description A This icon appears when you press [FN/ALPHA] once, indicating it is set to alphabetic mode for typing capital letters. a This icon appears when you press [FN/ALPHA] twice, indicating it is set to alphabetic mode for typing small letters.
Chapter 1 錯誤! 尚未定義樣式。 1.3.2 KEYPAD LAYOUT The layout of the 21-key keypad is similar to that of a telephone, which consists of an alphanumeric keypad, navigation and function keys, as well as assorted characters. By default, it is set to numeric mode. Press the [FN/ALPHA] key to enter alpha mode, capital or small letters.
8000 Series Mobile Computer Reference Manual 1.4 LCD The mobile computer comes with a 3” FSTN graphic LCD, 100 by 64 pixels resolutions, which can be programmed to display text or graphics, such as specific font and company logo, to meet varying application needs.
Chapter 1 錯誤! 尚未定義樣式。 1.5 NOTIFICATIONS 1.5.1 STATUS LED The dual-color LED above the screen is used to provide information on the charging status and can be programmed to provide information that helps diagnosing. For example, if you are using AG Runtime, you will be informed of the scanning result immediately. The green LED is used for "Good Read" while collecting data. Tasks Green LED Red LED Charging 8000 --- On Charging done On --- Good Read On --- Error occurs --- On 1.5.
8000 Series Mobile Computer Reference Manual 1.6 DATA CAPTURE 1.6.1 SCAN ENGINE OPTIONS Delivering flexibility to meet different requirements, the following scan engine options are provided — 1D CCD scan engine 1D Laser scan engine 1.6.2 SYMBOLOGIES SUPPORTED The mobile computer is capable of scanning barcodes of a number of symbologies that are enabled by default while running the preloaded AG runtime. Refer to section 3.3.1 Reader for functional test.
Chapter 1 錯誤! 尚未定義樣式。 EAN/UPC EAN-8 EAN-8 Addon 2 Disabled EAN-8 Addon 5 Disabled EAN-13 Enabled EAN-13 & UPC-A Addon 2 Disabled EAN-13 & UPC-A Addon 5 Disabled ISBN Disabled UPC-E0 Enabled UPC-E1 Disabled UPC-E Addon 2 Disabled UPC-E Addon 5 Disabled UPC-A RSS Enabled Enabled RSS-14 Disabled RSS Limited Disabled RSS Expanded Disabled 17
8000 Series Mobile Computer Reference Manual 1.7 COMMUNICATIONS VIA THE CRADLE 1.7.1 SETTING UP THE CRADLE The cradle is designed for charging and communications at the same time. You may choose a cradle type that best suits your needs. 1) Place the cradle on a flat and clean surface. 2) Connect the power supply cord to the power jack on the back of the cradle, and then connect the other end of the power supply cord to a suitable power outlet. The cradle is ready for charging the mobile computer.
Chapter 1 錯誤! 尚未定義樣式。 Line Jack − √ − Phone Jack − √ − RJ-45 Port − − √ IP Reset Switch − − √ Note: (1) Modem Cradle — Delivering flexibility in making a connection, the Modem Cradle integrates the modem functionality (56 kbps) into the cradle. (2) Ethernet Cradle — Refer to the Ethernet Cradle manual for more information.
8000 Series Mobile Computer Reference Manual 1.8 COMMUNICATIONS OVER WIRELESS NETWORKS The 8000 Series Mobile Computer supports state-of-the-art wireless technologies so that it can send/receive data in real time in an efficient way. WPAN: WPAN: WLAN: Infrared (IR/IrDA) technology for data exchange, embedded Bluetooth technology for cable replacement & data exchange, embedded IEEE 802.11b/g for wireless networking, optional Generally, the coverage of each technology can be viewed as follows.
Chapter 1 錯誤! 尚未定義樣式。 1.8.1 IR/IrDA The mobile computer has an integrated IR port on the bottom, which can directly establish connection with an IR device for printing or data exchange. Simply have the IR port of the mobile computer toward the IR port of the target device. This IR port supports CipherLab proprietary IR communication protocol and standard IrDA protocol.
8000 Series Mobile Computer Reference Manual 1.8.2 BLUETOOTH Bluetooth technology is for cable replacement & data exchange. With built-in Bluetooth module, the mobile computer can directly communicate with any Bluetooth enabled device, not necessarily line-of-sight. Serial Port Profile (SPP) is for ad-hoc networking, without going through any access point. Dial-Up Networking Profile (DUN) makes use of a Bluetooth modem or mobile phone as a wireless modem.
Chapter 1 錯誤! 尚未定義樣式。 1.8.3 IEEE 802.11b/g The 8071 mobile computer can easily connect to legacy networks through access points (APs). Roaming among different networks is possible. IEEE 802.11b/g is an industrial standard for Wireless Local Area Networking (WLAN), which enables wireless communications over a long distance. The speed of connection between two wireless devices will vary with range and signal quality. To maintain a reliable connection, the data rate of the 802.
8000 Series Mobile Computer Reference Manual 24
Chapter 2 LEARNING SOFTWARE ARCHITECTURE This chapter mainly describes the software inside the mobile computer. It consists of three modules — Kernel, System, and Application; each has a function menu.
8000 Series Mobile Computer Reference Manual Figure 9: Software Architecture IN THIS CHAPTER 2.1 Application Module ..................................................... 27 2.2 System Configuration .................................................
Chapter 2 錯誤! 尚未定義樣式。 2.1 APPLICATION MODULE For easy development of applications, the mobile computer ships with development tools on the CD-ROM. It includes Windows-based programs Application Generator (batch and WLAN), CipherNet (VT and 5250), download utilities, etc. 2.1.1 APPLICATION GENERATOR (AG) The mobile computer is preloaded with AG Runtime. When you turn on the mobile computer, it displays the Main Menu of AG application, as shown below.
8000 Series Mobile Computer Reference Manual 2.1.3 USER PROGRAM You may need to develop your own application program. For developing custom applications, CipherLab provides BASIC and C compliers through licensing. For detailed information, please contact your sales representative. 2.2 SYSTEM CONFIGURATION For managing system configurations and multiple programs, each mobile computer comes with the System Menu, Kernel, and Program Manager.
Chapter 3 SYSTEM MENU The System Menu is generated by a powerful utility, which offers an interface for engineers (programmers or system integrator) to view system information, change the configuration parameters, download programs and run diagnostics. This menu is designed for engineering tests and maintenance ONLY. For this reason, the System Menu provides password protection to prevent unauthorized users from accidentally changing system settings.
8000 Series Mobile Computer Reference Manual 3.1 INFORMATION Here provides important system information to help diagnose the system. System Menu > 1.
Chapter 3 錯誤! 尚未定義樣式。 3.2 SETTINGS You can change the default settings here. System Settings Default Values Clock blank Backlight Period 20 seconds, Level 2 CPU Speed Full speed Auto Off 10 minutes Power On Mode Program Resume Key Click Tone 2 System Password Open access Font System font Default Set (= Reset to Default) Load factory settings 3.2.1 CLOCK Set date and time for Real Time Clock. Enter two digits for the year, i.e. 04 for 2004. 3.2.
8000 Series Mobile Computer Reference Manual 3.2.5 POWER ON OPTIONS Set the startup screen once the mobile computer is turned on: Program Resume Press [ENTER] to select “Program Resume” or “Program Restart”. When selected, the mobile computer will start from the last session of program before it is turned off. Program Restart Press [ENTER] to select “Program Resume” or “Program Restart”. When selected, the mobile computer will start from the first session of the program. 3.2.
Chapter 3 錯誤! 尚未定義樣式。 3.3 TESTS Here provides functional tests for key parts. 3.3.1 READER The supported symbologies depend on the scan engine you use. Refer to section 1.6 Data Capture for symbologies that are enabled by default. For symbologies that are disabled by default, they must be enabled through programming. Test the reading performance of the scanner. Press [SCAN] to start. To stop and exit the test, press any key. 3.3.2 BUZZER Test the buzzer with different frequency/duration combinations.
8000 Series Mobile Computer Reference Manual 3.3.6 ECHO TEST After a physical connection is established properly, run the utility “Echo Test” on your computer and start this test on your mobile computer. Select a desired baud rate. To stop and exit the test, press [ESC]. IR (Cradle-IR) This echo test is to verify connectivity via IR between the mobile computer and any cradle. MODEM This echo test is to verify connectivity via modem. A telephone line must be connected to the Modem Cradle.
Chapter 3 錯誤! 尚未定義樣式。 3.4 MEMORY Here provides information and initialization function of the memory. 3.4.1 SIZE INFORMATION RAM Flash — onboard SRAM for data memory — program memory 3.4.2 INITIALIZE Initialize the data memory. Warning! The contents of the data memory (SRAM) will be wiped out after memory initialization.
8000 Series Mobile Computer Reference Manual 3.5 POWER Here shows current voltage consumption. Main (battery) It shows dynamic status of the battery pack, which is used as the main power source. Backup (battery) It shows dynamic status of the button cell, which is used to retain data in SRAM. Warning! 36 Always examine the battery icon on the device screen so that you will be alerted for a low battery condition.
Chapter 3 錯誤! 尚未定義樣式。 3.6 LOAD PROGRAM Here you can access the Load Program service provided by the kernel. Because the kernel will take over the job, you will not be able to return to the System Menu by pressing [ESC]. After downloading, restart the mobile computer to activate the new program. .SHX Program Download one of the following C program files and/or one font file: Program File Font File AG Runtime (U*.shx) CipherNet Runtime (80xx-5250.shx, 80xx-VT.shx) BASIC Runtime* (BC*.
8000 Series Mobile Computer Reference Manual 3.7 SERIAL PPP MENU This submenu is for establishing a PPP connection via the Modem Cradle or any generic modem. You must configure these parameters correctly. Note: Point-to-Point Protocol (PPP) is a method of connecting the mobile computer to the Internet over serial links. It sends TCP/IP packets to a server that connects to the Internet.
Chapter 3 錯誤! 尚未定義樣式。 3.7.1 INFORMATION Information of library version can be viewed here. Serial PPP Menu > 1. Information LIB C library version for PPP BSC BASIC Run-time version, if a BASIC application is downloaded. Below are available libraries that support (1) PPP connection over serial links (2) Ethernet connection – Transparent mode. Series Model # External Libraries 8000 8000 (batch) 80PPP.lib 8001 (batch) 80PPP.lib 8061/8062 (Bluetooth) 80PPP.lib OR 80BNEP.lib 8071 (802.
8000 Series Mobile Computer Reference Manual 3.7.2 CONNECTION SET DialUp Number Enter the number provided by your ISP. Login Name Enter the login name provided by your ISP. Login Password Enter the login password provided by your ISP. Baud Rate Select a desired baud rate. Note: By default, the baud rate is set to 57600 bps on the Modem Cradle. For any other value, such as 115200/38400/19200/9600, you must configure through the DIP switch on the IR control board.
Chapter 3 錯誤! 尚未定義樣式。 3.7.3 ECHO TEST This echo test is used for verifying connectivity via Point-to-Point Protocol. For the Modem Cradle, its physical connectivity can be verified in System Menu > Tests > Echo Test > IR or MODEM. Enter the IP address of a server with which a PPP connection is desired. Then, it will try to connect to the server.
8000 Series Mobile Computer Reference Manual 3.8 IR NETWORK MENU (ETHERNET VIA IR) This submenu is for Ethernet connection via IR networking. You must configure these parameters correctly. Note: The Ethernet Cradle is required for establishing Ethernet connection via IR.
Chapter 3 錯誤! 尚未定義樣式。 3.8.1 INFORMATION Information of Ethernet network configuration can be viewed here. IR Network Menu > 1. Information DHCP DHCP server in use or not IP IP address of the mobile computer Mask Subnet Mask Gate Default Gateway Note: For Transparent mode, refer to Serial PPP Menu for available libraries.
8000 Series Mobile Computer Reference Manual 3.8.2 NETWORK SETTING Set parameters for IP networking. DHCP Options - Enable or Disable Subnet Mask Enter a new Mask IP, if necessary. Local IP Address Enter a new address for the mobile computer, if necessary. Default Gateway Enter a new address for the default Gateway, if necessary. DNS Server Enter a new address for the DNS server, if necessary. Domain Name The domain name of the host is displayed when DHCP server is enabled.
Chapter 3 錯誤! 尚未定義樣式。 3.8.3 ECHO TESTS The Ethernet Cradle supports three working modes: Data Mode Modem Mode Transparent Mode These echo tests are used for verifying connectivity via the Ethernet Cradle. For details, refer to the Ethernet Cradle manual. Data Mode Set the Ethernet Cradle in Data mode. The mobile computer works as a client. Modem Mode Set the Ethernet Cradle in Modem mode. The mobile computer works as a client. Transparent Mode 1. Client Mode - Set the mobile computer as a client.
8000 Series Mobile Computer Reference Manual 3.9 BLUETOOTH MENU — 8061/8062 This submenu is for the built-in Bluetooth module to work with other Bluetooth enabled devices. You must configure these parameters correctly. Note: This submenu is generated only when the Bluetooth module is present. Bluetooth Settings Default Value Connect Setting SPP DUN PAN Items Need to Be Checked Local Name Model no. + Serial no.
Chapter 3 錯誤! 尚未定義樣式。 3.9.1 INFORMATION Information of network configuration can be viewed here. Bluetooth Menu > 1. Information LIB C library version for Bluetooth (BNEP) MAC MAC ID of the Bluetooth module ID A name given to the mobile computer for identification. CTY By default, it is made up of model No. and the serial number. (Identical to 2. Connect Set > 1. Local Name) "Normal" means all 79 channels are available for frequency-hopping (There are bandwidth limitations for 2.
8000 Series Mobile Computer Reference Manual 3.9.2 CONNECT SETTING A basic Bluetooth system can be configured as (1) point to point - DUN mode, and (2) point to multi-point - SPP or PAN mode. Set the following parameters if necessary. Local Name Enter a name for identifying the mobile computer. By default, it is made up of model No. and the serial number. Remote Name Enter a name for making a specific connection. The remote name must be one of those in the Freq. Dev. List.
Chapter 3 錯誤! 尚未定義樣式。 3.9.3 SECURITY Set or modify security parameters. Authentication Options - Enable or Disable PIN Code Define the encryption key values. Up to 16 characters, using ASCII code. Note: When authentication is enabled without providing a pre-set PIN code, the mobile computer supports dynamic input of PIN code during pairing.
8000 Series Mobile Computer Reference Manual 3.9.4 ECHO TESTS These echo tests are used for verifying connectivity to make sure the mobile computer is within coverage. Press [ESC] to stop and exit the test. In PAN mode, the echo test helps measure the coverage of the range, estimate the number of APs and mobile computers needed, and determine the topology of deploying APs. SPP: Serial Port Profile It is used for ad hoc networking, without going through any access point.
Chapter 3 錯誤! 尚未定義樣式。 - Use the Bluetooth COM port that has been configured as “outgoing”. - Set Action Mode to “Passive”. 3. Start the echo test on both ends. 4. The mobile computer will wait for PC (master) to start the connection. 5. Enter the preset PIN code for authentication on your computer. DUN Modem The mobile computer will try to connect to a Bluetooth modem or mobile phone. 1. Pairing with your mobile phone must be completed first. Select “DialUp Network” for Target Machine options. 2.
8000 Series Mobile Computer Reference Manual BNEP Server Set the mobile computer as a server. It will try to connect to an AP. 1. Pairing with an AP must be completed first. Select “Access Point” for Target Machine options. Note that you must disable Authentication and clear the preset PIN code when connecting to Bluetooth AP (3560). 2. Run the Echo Test program on your computer. Associated settings include - Select “TCP/IP – Client” for interface. - Enter Remote IP and port number.
Chapter 3 錯誤! 尚未定義樣式。 3.9.5 PAIRING TEST The pairing procedure is for the creation and exchange of a link key between two Bluetooth-enabled devices. The devices use the link key for future authentication when exchanging information. 1) The mobile computer will start with making an inquiry so that the system can generate a list of device(s) that has been discovered nearby. 2) Select a desired target device. 3) Select a Bluetooth service from the “Target Machine” menu.
8000 Series Mobile Computer Reference Manual 3.9.6 FREQ. DEV. LIST The Frequent Device List is used to store a list of target device(s) that the mobile computer has been connected to lately. After each successful pairing, the system will update the list. Note: To unpair any device, simply delete the device from this list. This list can show information of up to eight target devices that provides different Bluetooth services. It can list only one device that provides the Bluetooth Serial Port service.
Chapter 3 錯誤! 尚未定義樣式。 3.9.7 NETWORK SETTING Set parameters for IP networking. DHCP Options - Enable or Disable Subnet Mask Enter a new Mask IP, if necessary. Local IP Address Enter a new address for the mobile computer, if necessary. Default Gateway Enter a new address for the default Gateway, if necessary. DNS Server Enter a new address for the DNS server, if necessary. Domain Name The domain name of the host is displayed when DHCP server is enabled.
8000 Series Mobile Computer Reference Manual 3.10 WI-FI MENU — 8071 This submenu is for 802.11b/g wireless networking. You must configure these parameters correctly. Note: This submenu is generated only when the Wi-Fi module is present. Wi-Fi Settings Default Value Network Setting Ad-hoc Infrastructure Items Need to Be Checked DHCP Enabled --- v SubNet Mask 255.255.128.0 v v Local IP Address 0.0.0.0 v v Default Gateway 0.0.0.0 --- v DNS Server 0.0.0.
Chapter 3 錯誤! 尚未定義樣式。 3.10.1 INFORMATION Information of network configuration can be viewed here. Wi-Fi Menu > 1. Information LIB C library version for WLAN (802.11b/g) Ver Firmware version of the module chipset MAC MAC ID of the 802.11b/g module ID A name given to the mobile computer for identification. By default, it is made up of model No. and the serial number. (Identical to 3. WLAN Setting > 1.
8000 Series Mobile Computer Reference Manual 3.10.2 NETWORK SETTING Set parameters for IP networking. DHCP Options - Enable or Disable Subnet Mask Enter a new Mask IP, if necessary. Local IP Address Enter a new address for the mobile computer, if necessary. Default Gateway Enter a new address for the default Gateway, if necessary. DNS Server Enter a new address for the DNS server, if necessary. Domain Name The domain name of the host is displayed when DHCP server is enabled.
Chapter 3 錯誤! 尚未定義樣式。 3.10.3 WLAN SETTING Wireless networking can operate in two modes – (1) Ad-hoc mode: peer-to-peer, and (2) Infrastructure mode: point to multi-point through access points. Set the following parameters. Local Name Enter a name for identifying the mobile computer. By default, it is made up of model No. and the serial number. SS ID This refers to Service Set ID or Identifier. The mobile computer can ONLY communicate with access points that have the same SS ID.
8000 Series Mobile Computer Reference Manual 3.10.4 SECURITY Set or modify security parameters. WEP: EAP: WPA: Wired Equivalent Privacy Extensible Authentication Protocol Wi-Fi Protected Access Authentication [1] Open System [0] Share Key Default authentication type Enabled (For Share Key, it must be enabled!) This requires implementing WEP key.
Chapter 3 錯誤! 尚未定義樣式。 3.10.5 ECHO TESTS This function is used to measure the coverage of the range, estimate the number of APs and mobile computers needed, and determine the topology of deploying APs. Client Mode Set the mobile computer as a client. Enter the IP address of a server with which a connection is desired. Then, it will try to connect to an AP. 1. Run the Echo Test program on your computer. Associated settings include - Select “TCP/IP – Server” for interface. - Set Action Mode to “Passive”. 2.
8000 Series Mobile Computer Reference Manual While running echo tests, if WPA setting is enabled for security, the SSID and Passphrase will be processed to generate a pre-share key. Note: If you change the SSID or Passphrase, it will have to re-generate a pre-share key. 1) For initial association with an access point, you will see an antenna icon developing on the screen to indicate that the mobile computer is processing a pre-share key.
Chapter 3 錯誤! 尚未定義樣式。 Once the connection of echo test is established, the details will be displayed as illustrated below. Link Quality (“Q”) will be the most important element while the others are for your reference. Q (Link Quality) T (Transmit Speed) S (Signal Level) N (Noise Level) 0 ~ 10 Very Poor 1 Mbps 0 ~ 10 Weak 1 Weak 10 ~ 15 Poor 2 Mbps 30 ~ 60 Moderate 2~3 Moderate 15 ~ 30 Good 5.
8000 Series Mobile Computer Reference Manual 64
Chapter 4 PROGRAM MANAGER & KERNEL This chapter explains Program Manager and Kernel that manage multiple programs and firmware upgrade. IN THIS CHAPTER 4.1 Program Manager ...................................................... 65 4.2 Kernel ...................................................................... 70 4.1 PROGRAM MANAGER The mobile computer supports multiple applications and languages.
8000 Series Mobile Computer Reference Manual 4.1.1 DOWNLOAD Here provides a full list of programs that are currently stored on the mobile computer with size information. Multiple application programs can be downloaded through a variety of interfaces. Upon completion of downloading, you are allowed to input a name for the program. If there is no need to rename the program, simply press [ENTER] to leave as it is.
Chapter 4 錯誤! 尚未定義樣式。 SPARE MEMORY SECTORS (1 ~ 6) Additional program files can be directly downloaded to these sectors. Download a program file to an empty sector: 1. Select an empty sector by pressing the corresponding number and then [Enter]. 2. Select a desired baud rate for downloading. 3. Connect the RS-232 cable and wait for a few seconds to establish a connection… 4. To abort the action, press [ESC]. Then press [ESC] again to return to the menu.
8000 Series Mobile Computer Reference Manual 4.1.2 ACTIVATE The list shows the entire spare programs stored on the mobile computer. From the list, you can select from 1 to 6 and activate one of them. The selected program will be copied to the active memory sector and replace the current one. Note: A font file cannot be activated. TO CLEAR FILE SYSTEM When screen appears, “Press [ESC] to clear file” means the file system in the SRAM will be cleared out by pressing [ESC].
Chapter 4 錯誤! 尚未定義樣式。 4.1.3 UPLOAD You may duplicate one or all of the programs from the mobile computer to a host computer or another mobile computer. This can be used to clone software on mobile computers. Note: To clone all of the programs, the target mobile computer cannot have any other program downloaded except the active one; that is, Memory Sectors 1~6 must be empty! The procedures are similar to those for downloading programs.
00 Series Mobile Computer Reference Manual 4.2 KERNEL The kernel resides in the innermost core of the system. It has the highest security and is always protected by the system. When the application program is corrupted and the System Menu fails, the Kernel Menu provides an access to fix the system. Warning! The Kernel Menu is NOT for the use of any end users. How to access the Kernel Menu? 1) When the last session is in the System Menu or Program Manager, simply turn off the mobile computer.
Chapter 4 錯誤! 尚未定義樣式。 4.2.2 LOAD PROGRAM You can download one program file to the active memory sector, as well as one font file to the memory address assigned by the system. After downloading, restart the mobile computer to activate the new program. New application program or program update And/or one font file, i.e.
8000 Series Mobile Computer Reference Manual Baud Rate 115200 (bps) Supported on CipherLab software, including download utilities. 76800 (bps) N/A 57600 (bps) Supported on CipherLab software, including download utilities. 38400 (bps) Supported on CipherLab software, including download utilities. 19200 (bps) Supported on CipherLab software, including download utilities. 9600 (bps) Supported on CipherLab software, including download utilities.
Chapter 4 錯誤! 尚未定義樣式。 4.2.3 KERNEL UPDATE The kernel might need to be updated to improve performance or due to other considerations. To download a kernel update (K*.shx), the procedure is the same as that for downloading a program. Any attempt to download an older version will be rejected. The system will restart itself right after downloading. Warning: Do not turn off the mobile computer while downloading a kernel update or re-starting the mobile computer.
8000 Series Mobile Computer Reference Manual 4.2.5 BLUETOOTH MENU — 8061/8062 This submenu is the same as the one under the System Menu except for the following items: "2. Connect Set > 5. BT-GPRS AP Name" is not provided. "4. Echo Tests" is provided with SPP options only. "7. Network Setting" is not provided. Note: This submenu is generated only when the Bluetooth module is present.
SPECIFICATIONS 8000 8001 8020 8021 8061 8062 8071 IR/IrDA √ √ √ √ √ √ Bluetooth Class 1 – – – – √ – 802.
8000 Series Mobile Computer Reference Manual Environmental Characteristics (H) 26 Weight (Laser and battery included) 123 g Temperature Operating : -10 °C to 60 °C Storage: -20 °C to 70 °C Operating : 10% to 90% non-condensing Storage: 5% to 95% non-condensing Humidity Programming 32 120 g – 35 – 125 g 166 g Impact Resistance 1.
Appendix I DOWNLOAD UTILITIES For easy development of applications, the mobile computer ships with development tools on the CD-ROM. It includes Windows-based Application Generator programs, batch and WLAN, as well as download utilities. The download utilities are provided for you to download a program (*.SHX or *.SYN) to the mobile computer. Currently, the program ProgLoad.exe has replaced several previously released utilities as shown below. Download.exe IRLoad.exe SynLoad.exe : to download a *.
8000 Series Mobile Computer Reference Manual PROGLOAD.EXE This all-in-one utility supports all the file types and communications interfaces. Run the program on your computer. The following dialog box pops up. Click to select Comm type, COM port, and Baud rate. Choose your file… Communication Type RS-232/IrDA Connection via direct RS-232 cable, IrDA port, or Bluetooth SPP (= Download.exe) Serial IR Connection via cradle (= IRLoad.
Appendix I 錯誤! 尚未定義樣式。 IRLOAD.EXE This utility is provided when you establish a connection via the cradle. 1) Run the program on your computer. 2) Choose a .SHX file. 3) Select COM port properties. COMMAND LINE It also supports command line arguments. For example, IRLOAD U8000-114.SHX,2,1//COM2,115200 bps If command line arguments are not given, the user can select appropriate parameters from the pop-up dialog box.
8000 Series Mobile Computer Reference Manual DOWNLOAD.EXE This utility is provided when you establish a connection via serial interface, such as a direct RS-232 cable, IrDA port, or Bluetooth SPP. 1) Run the program. 2) Choose a .SHX file. 3) Select COM port properties. COMMAND LINE It also supports command line arguments.
Appendix II TROUBLESHOOTING The mobile computer cannot be turned on when you press the POWER key… Make sure the battery pack is installed properly. Re-charge the battery inside the mobile computer and monitor the charging status. (see 3.5) If the battery is faulty, replace it with a fresh and fully charged battery then. Charging error… Make sure the power cord is well connected between the cradle/charger and an outlet.
8000 Series Mobile Computer Reference Manual The reader does not decode after scanning… Unreadable barcode — Check if the barcode is defaced. A defaced barcode may not be readable. Un-programmed to read — Check if the scanner is programmed to read the symbologies (types of barcode) that you are trying to read. Try scanning a test barcode of the symbology you are trying to read. Dirty scan window — Check if the scan window gets dirty. Wipe it with a clean and dry cloth, and try again.
Appendix II 錯誤! 尚未定義樣式。 Over MODEM port via cradle — Check if the modem connection is correct and secured. Make sure the mobile computer is well seated inside the cradle. DO NOT remove the mobile computer or disconnect the cradle before communications are done. If the problem persists, run the IR Echo Test to check the IR interface between the mobile computer and the cradle. (see 3.3.6) Make sure the modem parameters are configured to match the parameters on the mobile computer.
