User's Manual
Table Of Contents
- 英文-2564MR Scanner User Guide_v1.00-FOR FCC IC-20170217- Important Notices
- Release Notes
- Introduction
- Quick Start
- Understanding the Barcode Scanner- 1.1 Battery
- 1.2 Memory
- 1.3 LED Indicator
- 1.4 Beeper
- 1.5 Send “NR” to Host
- 1.6 Scan Modes
- 1.7 Scanning Timeout
- 1.8 Delay between Re-read
- 1.9 Read Redundancy (1D)
- 1.10 Addon Security for UPC/EAN Barcodes
- 1.11 Auto-Sense Mode
- 1.12 Negative Barcodes
- 1.13 Picklist Mode
- 1.14 Mobile Phone/Display Mode
- 1.15 Illumination Brightness
- 1.16 Serial Number Stamp
- 1.17 2D Decode Setting
 
- Selecting Output Interface- 2.1 BT HID- 2.1.1 Activate BT HID & Select Keyboard Type
- 2.1.2 Reset Connection
- 2.1.3 Keyboard Settings
- 2.1.4 Inter-Character Delay
- 2.1.5 Inter-Function Delay
- 2.1.6 HID Character Transmit Mode
- 2.1.7 Special Keyboard Feature
- 2.1.8 Keypad Support for iPhone/iPad
- 2.1.9 Transmit Speed
- 2.1.10 Simple Pairing for iPhone/iPad
- 2.1.11 BT HID Slave/Master Switching
- 2.1.12 BT HID Auto-Reconnection
 
- 2.2 BT SPP Slave
- 2.3 BT SPP Master
- 2.4 Keyboard Wedge via BT Cradle
- 2.5 RS-232 via BT Cradle
- 2.6 USB HID via BT Cradle
- 2.7 USB Virtual COM via BT Cradle
 
- 2.1 BT HID
- Setting up a WPAN Connection
- Changing Symbology Settings- 4.1 Codabar
- 4.2 Code 25 – Industrial 25
- 4.3 Code 25 – Interleaved 25
- 4.4 Code 25 – Matrix 25
- 4.5 Code 25 – Chinese 25
- 4.6 Italian Pharmacode (Code 32)
- 4.7 Code 39
- 4.8 Trioptic Code 39
- 4.9 Code 93
- 4.10 Code 128
- 4.11 GS1-128 (EAN-128)
- 4.12 ISBT 128
- 4.13 GS1 DataBar (RSS Family)
- 4.14 MSI
- 4.15 EAN-8
- 4.16 EAN-13
- 4.17 UCC Coupon Extended Code
- 4.18 UPC-A
- 4.19 UPC-E
- 4.20 Code 11
- 4.21 Composite Code
- 4.22 US Postal Code
- 4.23 UK Postal Code
- 4.24 More Postal Code
- 4.25 2D Symbologies
- 4.26 Macro PDF
 
- Defining Output Format
- Applying Formats for Data Editing
- Specifications
- Firmware Upgrade
- Host Serial Commands
- Keyboard Wedge Table
- Numeral Systems
- Reading Driver Licenses
 
Caution!   
Any changes or modifications not expressly approved by the party responsible for compliance could 
void the user's authority to operate the equipment. 
This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. 
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the 
following two conditions: 
(1) This device may not cause interference; and 
(2) This device must accept any interference, including interference that may cause undesired 
operation of the device. 
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts 
de licence. L’exploitation est autorisée aux deux conditions suivantes : 
(1) l’appareil ne doit pas produire de brouillage; 
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est 
susceptible d’en compromettre le fonctionnement. 
The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and 
compliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and 
compliance.   
Le dispositif rencontre l'exemption des limites courantes d'évaluation dans la section 2.5 de RSS 102 et 
la conformité à l'exposition de RSS-102 rf, utilisateurs peut obtenir l'information canadienne sur 
l'exposition et la conformité de rf. 










