User's Manual
Table Of Contents
- 英文-2564MR Scanner User Guide_v1.00-FOR FCC IC-20170217- Important Notices
- Release Notes
- Introduction
- Quick Start
- Understanding the Barcode Scanner- 1.1 Battery
- 1.2 Memory
- 1.3 LED Indicator
- 1.4 Beeper
- 1.5 Send “NR” to Host
- 1.6 Scan Modes
- 1.7 Scanning Timeout
- 1.8 Delay between Re-read
- 1.9 Read Redundancy (1D)
- 1.10 Addon Security for UPC/EAN Barcodes
- 1.11 Auto-Sense Mode
- 1.12 Negative Barcodes
- 1.13 Picklist Mode
- 1.14 Mobile Phone/Display Mode
- 1.15 Illumination Brightness
- 1.16 Serial Number Stamp
- 1.17 2D Decode Setting
 
- Selecting Output Interface- 2.1 BT HID- 2.1.1 Activate BT HID & Select Keyboard Type
- 2.1.2 Reset Connection
- 2.1.3 Keyboard Settings
- 2.1.4 Inter-Character Delay
- 2.1.5 Inter-Function Delay
- 2.1.6 HID Character Transmit Mode
- 2.1.7 Special Keyboard Feature
- 2.1.8 Keypad Support for iPhone/iPad
- 2.1.9 Transmit Speed
- 2.1.10 Simple Pairing for iPhone/iPad
- 2.1.11 BT HID Slave/Master Switching
- 2.1.12 BT HID Auto-Reconnection
 
- 2.2 BT SPP Slave
- 2.3 BT SPP Master
- 2.4 Keyboard Wedge via BT Cradle
- 2.5 RS-232 via BT Cradle
- 2.6 USB HID via BT Cradle
- 2.7 USB Virtual COM via BT Cradle
 
- 2.1 BT HID
- Setting up a WPAN Connection
- Changing Symbology Settings- 4.1 Codabar
- 4.2 Code 25 – Industrial 25
- 4.3 Code 25 – Interleaved 25
- 4.4 Code 25 – Matrix 25
- 4.5 Code 25 – Chinese 25
- 4.6 Italian Pharmacode (Code 32)
- 4.7 Code 39
- 4.8 Trioptic Code 39
- 4.9 Code 93
- 4.10 Code 128
- 4.11 GS1-128 (EAN-128)
- 4.12 ISBT 128
- 4.13 GS1 DataBar (RSS Family)
- 4.14 MSI
- 4.15 EAN-8
- 4.16 EAN-13
- 4.17 UCC Coupon Extended Code
- 4.18 UPC-A
- 4.19 UPC-E
- 4.20 Code 11
- 4.21 Composite Code
- 4.22 US Postal Code
- 4.23 UK Postal Code
- 4.24 More Postal Code
- 4.25 2D Symbologies
- 4.26 Macro PDF
 
- Defining Output Format
- Applying Formats for Data Editing
- Specifications
- Firmware Upgrade
- Host Serial Commands
- Keyboard Wedge Table
- Numeral Systems
- Reading Driver Licenses
 
2564MR Barcode Scanner User Guide 
    79 (y)  Chinese 25 
5A (Z)  N/A  7A (z)  Aztec 
5B ( [ )  GS1 DataBar (RSS)  7B ({)  Micro QR 
    7C (|)  USPS 4CB / One Code / 
Intelligent Mail 
    7D (})  UPU FICS Postal 
    7E (~)  UCC Coupon Extended Code 
3)  Barcode Length setting – read the “Decimal Value” barcode on page 263 for the 4-digit 
length of the (first) barcode. For example, read “0065”  for  barcode length of 65 
characters or read “0000” for any length.  
Note:  If not reading 0000 for any length, the 4-digit length must exclude prefix, suffix 
(0x0d by default), length code, etc. 
4)  Matching Character setting – read the “Hexadecimal Value” barcode on page 264 for the 
1
st
 character that must be found matching in the (first) barcode. For example, read “4” 
and “1” for matching character “A” as the first character in the barcode or read “00” for 
any character. 
5)  Read twice the “F” barcode on page 264 (“FF”) to complete the setting of each barcode. 
6)  Read the “Validate” barcode to end the editing of the barcode set. 
5.6.2 ACTIVATE THE CONCATENATION OF BARCODES 
By default, the output sequence editing of the concatenation of barcodes is not applied.  
When “Enforce Output Sequence” is enabled, all barcodes read by the scanner must meet 
with the criteria for the concatenation. If data is found excluded from all output sequence 
sets (= not meeting with the criteria), the scanner will not accept the reading, and therefore, 
data will not be transmitted. 
When “Apply Output Sequence” is enabled, only barcodes found meeting with the criteria 
are counted for the concatenation. Those found not meeting with the criteria are processed 
normally and individually. 
Note:  When it requires reading more barcodes to complete the “output sequence” 
requirements, the scanner will respond with one short beep (low tone). After reading 
an acceptable barcode, its LED indicator will become solid green and go off quickly (= 
Good Read).                 Upon completion 
of reading acceptable barcodes, the scanner will respond with one short beep (high 
tone) and its LED indicator will become solid green and go off quickly (= Good Read). 
206 
Enter Setup 










