User manual

ManualsBrandsCipherLab ManualsPrint & Scan2564

2564 Barcode Scanner

Setup barcodes included.

Version 1.00

Summary of content (291 pages)

PAGE 1
2564 Barcode Scanner Setup barcodes included. Version 1.
PAGE 2
Copyright © 2017 CIPHERLAB CO., LTD. All rights reserved The software contains proprietary information of CIPHERLAB CO., LTD.; it is provided under a license agreement containing restrictions on use and disclosure and is also protected by copyright law. Reverse engineering of the software is prohibited. Due to continued product development this information may change without notice.
PAGE 3
IMPORTANT NOTICES FOR USA This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
PAGE 4
FOR PRODUCT WITH LASER CAUTION This laser component emits FDA / IEC Class 2 laser light at the exit port. Do not stare into beam. SAFETY PRECAUTIONS  DO NOT expose the scanner to any flammable sources.  Under no circumstances, internal components are self-serviceable.  For AC power adaptor, a socket outlet shall be installed near the equipment and shall be easily accessible. Make sure there is stable power supply for the scanner or its peripherals to operate properly.
PAGE 5
RELEASE NOTES Version Date Notes 1.00 Sep.
PAGE 6
PAGE 7
CONTENTS IMPORTANT NOTICES ........................................................................................................- 3 For USA........................................................................................................................................ - 3 For Canada ................................................................................................................................. - 3 For Product with Laser .............................................................
PAGE 8
2564 Barcode Scanner User Guide 1.2.3 Free Memory .............................................................................................................. 28 1.3 LED Indicator ....................................................................................................................... 29 1.3.1 Good Read LED.......................................................................................................... 30 1.3.2 Good Read LED Duration .................................................
PAGE 9
2564 Barcode Scanner User Guide 2.2 BT SPP Slave ....................................................................................................................... 61 2.2.1 Activate BT SPP Slave Mode................................................................................. 61 2.2.2 Inter-Function Delay ............................................................................................... 61 2.2.3 ACK/NAK Timeout ...........................................................................
PAGE 10
2564 Barcode Scanner User Guide 3.1.1 Connect to Cradle ..................................................................................................... 98 3.1.2 Change Interface ...................................................................................................... 99 3.1.3 Configure Related Settings .................................................................................100 3.2 Connecting via Bluetooth® Dongle....................................................................
PAGE 11
2564 Barcode Scanner User Guide 4.9.1 EAN-13 Addon Modes ...........................................................................................135 4.9.2 Convert to ISBN ......................................................................................................137 4.9.3 Convert to ISSN ......................................................................................................137 4.9.4 Transmit Check Digit .............................................................................
PAGE 12
2564 Barcode Scanner User Guide 4.20.3 Security Level ........................................................................................................159 4.20.4 Code Length Qualification .................................................................................159 4.21 Composite Code .............................................................................................................161 4.21.1 Composite CC-A/B ...........................................................................
PAGE 13
2564 Barcode Scanner User Guide 6.4.3 Total Number of Fields .........................................................................................219 6.4.4 Field Settings............................................................................................................220 6.4.5 Pause Field Setting ................................................................................................226 6.5 Configuring Format — Define Transmission Sequence .....................................227 6.
PAGE 14
2564 Barcode Scanner User Guide Keyboard Wedge (Cradle) ....................................................................................................270 Remote USB HID (Cradle)....................................................................................................
PAGE 15
INTRODUCTION The small-form-factor Barcode Scanners are capable of reading 2D barcodes. The tethered handheld scanners are designed to help accelerate productivity while lowering the total cost of ownership. Intensive data collection jobs are made easier with fast, accurate barcode scanning in various working environments, especially in small businesses.
PAGE 16
2564 Barcode Scanner User Guide GETTING FAMILIARIZED WITH THE SCANNER AND THE CRADLE INSTALLING THE BATTERY TO THE SCANNER When you first receive the package, the rechargeable battery is stored separately from the scanner. Insert the battery into the scanner first so that it can be charged when sitting in the cradle. Note: Any improper handling may reduce the battery life. 1) Hold the scanner still and insert the battery into the battery compartment at the bottom of the scanner.
PAGE 17
Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь отображат SETTING UP THE CRADLE Capable of charging the scanner, the cradle is specifically designed for the scanner to communicate with a host computer wirelessly. Refer to 3.1.1 Connect to Cradle. Two LED indicators are provided for power and communications status.
PAGE 18
2564 Barcode Scanner User Guide CHARGING THE BATTERY VIA CRADLE The battery may not be charged to full for shipment. When you first receive the package, you will need to charge the battery to full before using the scanner. When using the RS-232 cable, it takes approximately 5 hours to charge the battery to full (from the power adaptor). Note: Battery charging stops when the temperature drops below 0°C or exceeds 40°C.
PAGE 19
Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь отображат CHARGING THE BATTERY VIA CHARGER The battery charger is provided for charging the battery only. You may purchase the charger separately. It takes approximately 3 hours to charge the battery to full. Note: Battery charging stops when the temperature drops below 0°C or exceeds 40°C. It is recommended to charge the battery at room temperature (18°C to 25°C) for optimal performance.
PAGE 20
2564 Barcode Scanner User Guide INSIDE THE PACKAGE The items included in the package may be different depending on your order. Rich choices of output interfaces are available to enhance the total performance of the scanner. Please refer to product specifications. Save the box and packaging material for future use in case it is need to store or ship the scanner.
PAGE 21
Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь отображат SYMBOLOGIES SUPPORTED Most of the popular barcode symbologies are supported, as listed below. Each can be individually enabled or disabled. The scanner will automatically discriminate and recognize all the symbologies that are enabled. Refer to Chapter 4 Changing Symbology Settingsfor details of each symbology.
PAGE 22
2564 Barcode Scanner User Guide GS1 DataBar Limited (RSS Limited) Disabled GS1 DataBar Expanded (RSS Expanded) Disabled Composite Code Composite CC-A/B Disabled Composite CC-C Disabled 2D Symbologies PDF417 Enabled MicroPDF417 Disabled Data Matrix Enabled Maxicode Enabled QR Code Enabled MicroQR Aztec Disabled Enabled Han Xin Disabled 8 Enter Setup
PAGE 23
QUICK START The configuration of the scanner can be done by reading the setup barcodes contained in this manual or via the ScanMaster software. This section describes the procedure of configuring the scanner by reading the setup barcodes and provides some examples for demonstration. Configuration Mode 1. Hold down the trigger about 2 seconds to turn on the scanner. It will respond with a long beep and its LED will come on-off shortly. 2. Have the scanner read the “Enter Setup” barcode.
PAGE 24
2564 Barcode Scanner User Guide Working Mode Upon powering up, the scanner will try to establish a connection with the BT cradle or a computer with Bluetooth® wireless technology. Refer to Chapter 3 Setting up a WPAN Connection for details. The connection between the scanners and the cradle is made easy and reliable. Note: If RS-232, USB Virtual COM or BT SPP is selected for output interface, the host can directly send serial commands to configure the scanner. For example, run HyperTerminal.
PAGE 25
Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь отображат ENTER CONFIGURATION MODE For the scanner to enter the configuration mode, have it read the "Enter Setup" barcode located at the bottom of almost every even page of this manual.  The scanner will respond with six beeps and its LED indicator will become flashing red after reading the barcode. Enter Setup For configuring scanner parameters, see “Read a Setup Barcode” below.
PAGE 26
2564 Barcode Scanner User Guide DEFAULT SETTINGS SAVE USER SETTINGS AS DEFAULTS For the scanner to keep the customized settings as user defaults, have it read the “Save as User Defaults” barcode. This is a normal setup barcode, and the scanner will respond with two beeps (low-high tone).  After reading the “Update” barcode, the current settings will be saved as user defaults.
PAGE 27
Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь отображат READ A SETUP BARCODE CONFIGURE PARAMETERS For most of the scanner parameters, only one read is required to set them to new values. The scanner will respond with two beeps (low-high tone) when each parameter is set successfully. But for a number of special parameters, multiple reads are required to complete the setting.
PAGE 28
2564 Barcode Scanner User Guide The example below shows how to save settings as “User Default” to restore user defaults later: Steps Action Scanner Feedback if Successful 1 Power on the scanner… The scanner will respond with a long beep (high tone) and its LED indicator will become solid red and go off quickly. 2 Enter the Configuration Mode… The scanner will respond with six beeps (high-low tone repeats three times), and its LED indicator will be flashing red.
PAGE 29
Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь отображат The example below shows how to set numeric parameters: Steps Action Scanner Feedback if Successful 1 Power on the scanner... The scanner will respond with a long beep (high tone) and its LED indicator will become solid red and go off quickly. 2 Enter the Configuration Mode… The scanner will respond with six beeps (high-low tone repeats three times), and its LED indicator will become flashing red.
PAGE 30
2564 Barcode Scanner User Guide The example below shows how to set string parameters: Steps Action Scanner Feedback if Successful 1 Power on the scanner... The scanner will respond with a long beep (high tone) and its LED indicator will become solid red and go off quickly. 2 Enter the Configuration Mode… The scanner will respond with six beeps (high-low tone repeats three times), and its LED indicator will become flashing red. 3 Read a Setup barcode...
PAGE 31
Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь отображат LIST THE CURRENT SETTINGS The current settings of all scanner parameters can be sent to the host computer for user inspection. The listing includes pages as shown below. Select the page of interest by having the scanner read the “List Page x” barcode. The scanner will respond with two beeps (low-high tone) and send the selected page to the host immediately.
PAGE 32
2564 Barcode Scanner User Guide Lists settings regarding Editing Format 1 (1/2) List Page 11 Lists settings regarding Editing Format 1 (2/2) List Page 12 Lists settings regarding Editing Format 2 (1/2) List Page 13 Lists settings regarding Editing Format 2 (2/2) List Page 14 Lists settings regarding Editing Format 3 (1/2) List Page 15 Lists settings regarding Editing Format 3 (2/2) List Page 16 Lists settings regarding Editing Format 4 (1/2) List Page 17 Lists settings regarding Editing Format
PAGE 33
Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь отображат CREATE ONE-SCAN SETUP BARCODES Most of the scanner parameters require only one read for setting new values. To facilitate configuring the scanner, create One-Scan setup barcodes for use.
PAGE 34
2564 Barcode Scanner User Guide 2D ONE-SCAN BARCODE Users can also scan a single 2D barcode combining with a series of serial commands to configure the scanner.
PAGE 35
Chapter 1 UNDERSTANDING THE BARCODE SCANNER This chapter explains the features and usage of the barcode scanner. IN THIS CHAPTER 1.1 Battery ...................................................................... 21 1.2 Memory ..................................................................... 26 1.3 LED Indicator ............................................................. 29 1.4 Beeper....................................................................... 31 1.5 Send “NR” to Host ......................
PAGE 36
2564 Barcode Scanner User Guide 1.1.2 POWER ECONOMY The scanner features “Power-Saving” and “Auto Power Off” giving consideration to the power issue that is generally critical for Bluetooth-enabled devices.
PAGE 37
Chapter 1 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь Note: Power-Saving won’t take effect when one of the following conditions is met: (1) the scanner has already established a BT HID/SPP connection, (2) the scanner is in the configuration mode, (3) the setting value of Power-Saving is greater than that of Auto Power Off. 1.1.2.
PAGE 38
2564 Barcode Scanner User Guide 1.1.3 POWER ECONOMY VS. WPAN CONNECTION Before the scanner can communicate with the host computer, Bluetooth connection (or WPAN connection) needs to be established. The scanner’s power economy always accommodates itself to the establishment of the WPAN connection. The following describes how the scanner carries out power economy before and after the establishment of the WPAN connection: Before establishing a WPAN connection successfully… 1.
PAGE 39
Chapter 1 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь from low to high upon the resumption. If the scanner fails to resume the connection, it will try every 5 seconds to re-connect to the host unless you have the scanner read the “Reset Connection” barcode.   For BT SPP Slave Mode, the scanner waits for the host to re-connect.  With the use of cradle, the scanner tries to re-connect the cradle unless you turn off the scanner.
PAGE 40
2564 Barcode Scanner User Guide 1.2 MEMORY The collected data can be sent back to a host computer one by one via the WPAN connection or stored in flash memory when the scanner is set to Memory mode. 1.2.1 TRANSMIT BUFFER By default, transmit buffer is enabled and for use when the scanner is out of range. Upon reading a barcode successfully within range, the scanner responds with one short beep (high tone) and its LED indicator becomes solid green and goes off quickly.
PAGE 41
Chapter 1 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь 1.2.2 MEMORY MODE The scanner keeps 4 MB flash memory for memory mode operation. When the scanner is in memory mode, it means any real-time connection established with host is disabled. Enable *Disable Warning: No real-time connection is allowed unless the memory mode is disabled. Memory Data Delay You may set a delay between each data record while transmitting data back to the host.
PAGE 42
2564 Barcode Scanner User Guide 8 sec Send Data The 4 MB flash memory on the scanner can store up to 246,723 scans based on EAN-13 barcodes. When it is used up, the scanner will respond with two short beeps (high-low tone) as a warning. You are advised to send data to the host immediately by having the scanner read the “Send Data” barcode below. It will resume the previous WPAN connection with host temporarily.
PAGE 43
Chapter 1 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь 1.3 LED INDICATOR The triple-color LED on top of the scanner is used to provide user feedback. For example, the LED becomes solid red and goes off quickly upon powering on or running out of transmit buffer. You may tell the difference by the beeps – you will hear a long beep of high tone when powering on the scanner, and a long beep of low tone when the transmit buffer becomes full.
PAGE 44
2564 Barcode Scanner User Guide 1.3.1 GOOD READ LED *Enable Good Read LED Disable Good Read LED 1.3.2 GOOD READ LED DURATION By default, the Good Read LED stays on for 40 milliseconds. Specify a value, ranging from 1 to 254 in units of 10 milliseconds. Good Read LED Time-out after 0.01~2.54 sec. (*40 ms) 1) Read the barcode above to specify the time interval before the Good Read LED goes off. 2) Read the “Decimal Value” barcode on page 251.
PAGE 45
Chapter 1 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь 1.4 BEEPER The scanner has a buzzer to give feedback for various operating conditions.
PAGE 46
2564 Barcode Scanner User Guide 1.4.
PAGE 47
Chapter 1 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь 1.4.
PAGE 48
2564 Barcode Scanner User Guide 1.4.3 LOW BATTERY ALARM By default, it will activate the beeper to give a warning when the battery charge gets low. In order to prevent data loss, you are advised to replace the battery immediately when you hear two short beeps (high tone).
PAGE 49
Chapter 1 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь 1.5 SEND “NR” TO HOST This feature only works when Keyboard Wedge or RS-232 is selected for output interface. Have the scanner send the “NR” string to the host to notify the No Read event.
PAGE 50
2564 Barcode Scanner User Guide 1.6 SCAN MODES Different scan modes are supported – select the scan mode that best suits the requirements of a specific application. Refer to the comparison table below.
PAGE 51
Chapter 1 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь 1.6.1 LASER MODE The scanner will start scanning once the trigger is held down.  The scanning won't stop until (1) a barcode is decoded, (2) the pre-set timeout expires, or (3) release the trigger. Note: Refer to “Scanning Timeout”. *Laser Mode 1.6.2 AUTO OFF MODE The scanner will start scanning once the trigger is pressed.
PAGE 52
2564 Barcode Scanner User Guide 1.6.4 AIMING MODE The scanner will aim at a barcode once the trigger is pressed, and start scanning when the trigger is pressed again within one second.  The scanning won't stop until (1) a barcode is decoded, and (2) the pre-set timeout expires. Aiming Mode Aiming Timeout Limit the aiming time interval (1~15). By default, the scanner time-out is set to 1 second. Aiming Time-out after 1~15 sec. (*1) 1.
PAGE 53
Chapter 1 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь 1.6.6 PRESENTATION MODE The scanner will be expecting barcodes. Whenever a barcode is brought within range, the scanner will be able to decode it. It is suggested to seat the scanner in the Auto-Sense Stand for hands-free operation. Presentation Mode Low Light Enhancement Enable Low Light Enhancement will cause the illumination to remain on at a low power in low lighting conditions.
PAGE 54
2564 Barcode Scanner User Guide 1.7 SCANNING TIMEOUT Specify the scanning time interval (1~254 sec.; 0= Disable) when the scan mode is set to any of the following –     Laser mode Auto Off mode Auto Power Off mode Aiming mode Scanner Time-out after 0~254 sec. (*10) 1) Read the barcode above to specify the time interval before the scan engine times out. 2) Read the “Decimal Value” barcode on page 251.
PAGE 55
Chapter 1 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь 1.
PAGE 56
2564 Barcode Scanner User Guide 1.9 READ REDUNDANCY (1D) Select the level of reading redundancy. For example,  If "No Redundancy" is selected, one successful decoding will make the reading valid and induce the "READER Event".  If "Two Times" is selected, it will take a total of three consecutive successful decoding of the same barcode to make the reading valid. The higher the reading redundancy is (that is, the more reading times the user selects), the slower the reading speed gets.
PAGE 57
Chapter 1 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь 1.10 ADDON SECURITY FOR UPC/EAN BARCODES The scanner is capable of decoding a mix of UPC/EAN barcodes with or without addons. The read redundancy (2~30 times; default is set to 2) allows changing the number of times to decode a UPC/EAN barcode before transmission. The more redundancy selected, the higher the reading security is, and thus, the slower the reading speed becomes.
PAGE 58
2564 Barcode Scanner User Guide 1.12 CABLE AUTO-DETECTION VIA BT CRADLE By default, this function is enabled that the cradle will detect the interface automatically. Connect the BT cradle to a host computer using the provided interface cable. After the BT connection between the scanner and the cradle is established, users can have the scanner read the setting barcodes below to enable/disable cable auto-detection on the cradle.
PAGE 59
Chapter 1 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь 1.14 MOBILE PHONE/DISPLAY MODE By default this mode is disabled. There is a big improvement in reading barcodes displayed on mobile phones and electronic displays when this mode is enabled. *Disable Enable 1.15 SERIAL NUMBER STAMP Decide whether to add the device serial number in front of the data transmitted. Add serial number in front of data *Disable 1.15.
PAGE 60
2564 Barcode Scanner User Guide 1.16 2D DECODE SETTINGS 1.16.1 AIMING PATTERN Enable/Disable the aiming pattern during scanning. *Enable Disable 1.16.2 DECODING ILLUMINATION Enable/Disable illumination during scanning.  Enabling illumination usually results in superior images. The effectiveness of the illumination decreases as the distance to the target increases.
PAGE 61
Chapter 2 SELECTING OUTPUT INTERFACE In order to establish a proper WPAN connection between your computer and the scanner, we suggest that you follow these instructions – 1) Install the battery and hold down the trigger for about 2 seconds to turn on the scanner. 2) Have the scanner read the “Enter Setup” barcode to enter the configuration mode. 3) Have the scanner read the associated barcodes to activate the desired interface. See the following sections for output interfaces supported.
PAGE 62
2564 Barcode Scanner User Guide 2.1 BT HID For BT HID, refer to Chapter 3 Setting up a WPAN Connection for related connection settings. Run any text editor on your computer, and the scanned data will be transmitted to the computer.
PAGE 63
Chapter 2 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь 2.1.1 ACTIVATE BT HID & SELECT KEYBOARD TYPE When BT HID interface is activated, you will have to select a keyboard type to complete this setting. By default, BT HID is activated on the scanner, and the keyboard type is set to PCAT (US). Activate BT HID & Select Keyboard Type… 1) Read the barcode above to activate BT HID and select a keyboard type. 2) Read the “Decimal Value” barcode on page 251.
PAGE 64
2564 Barcode Scanner User Guide 2.1.2 RESET CONNECTION For BT HID, you can only have the scanner connected to one computer at a time. If you want to connect the scanner to another host, you must have it read the “Reset Connection” barcode so that the current connection record will be cleared. Then, the scanner will restart itself automatically. Go through the whole process in 3.2.3 Connect to Dongle to establish a new connection.
PAGE 65
Chapter 2 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь 2.1.
PAGE 66
2564 Barcode Scanner User Guide US Keyboard Style – Normal QWERTY layout, which is normally used in western countries.  Select “Lower Row” for the “Digits Layout” setting because the upper row is for special characters. French Keyboard Style – AZERTY French layout; see below for French Keyboard Style.  Select “Upper Row” for the “Digits Layout” setting because the lower row is for special characters. German Keyboard Layout – QWERTZ German layout; see below for German Keyboard Style.
PAGE 67
Chapter 2 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь Digits Layout Select a proper layout that matches the alphabets layout. The scanner will make adjustments according to this setting.
PAGE 68
2564 Barcode Scanner User Guide Capital Lock Capital Lock State Description Capital Lock OFF Assuming that the status of Caps Lock on the keyboard is OFF, transmitted characters are exactly the same as in the barcode (when "case-sensitive" is selected for Alphabets Transmission). Capital Lock ON Assuming that the status of Caps Lock on the keyboard is ON, transmitted characters are exactly the same as in the barcode (when "case-sensitive" is selected for Alphabets Transmission).
PAGE 69
Chapter 2 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь Refer to 5.1 Letter Case. Digits Transmission By default, the alphanumeric keypad is used for transmitting digits. Select “Numeric Keypad” if you wish to use the keys on the numeric keypad.
PAGE 70
2564 Barcode Scanner User Guide Note: If you select “Numeric Keypad”, the Num Lock status of the physical keyboard should be “ON”. This setting is not supported on PDAs. Kanji Transmission Kanji Transmission is supported by the scanner when either Bluetooth HID, Keyboard Wedge via the cradle or USB HID via the cradle is selected for the output interface. By Kanji Transmission, when the host computer is running on Japanese Windows O.S.
PAGE 71
Chapter 2 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь 2.1.5 INTER-FUNCTION DELAY By default, the inter-function delay is set to zero. Specify a value, ranging from 0 to 254 in units of millisecond, to match the computer response time of the keyboard interface. Such delay time is inserted between every function code (0x01 ~ 0x1F) being transmitted. The longer the delay time is, the slower the transmission speed will be.
PAGE 72
2564 Barcode Scanner User Guide 2.1.7 SPECIAL KEYBOARD FEATURE By default, this interface employs special function codes (0x01 ~ 0x1F) defined in the Keyboard Wedge Table. However, users may want to get rid of these special codes within the barcodes to avoid data error. You can decide whether to apply the special keyboard feature. For further details please refer to Keyboard Wedge Table. *Apply Bypass 2.1.
PAGE 73
Chapter 2 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь Normal *Fast 2.1.10 SIMPLE PAIRING FOR IPHONE/IPAD The window requiring pairing passcode is always pop-up when you are using a Bluetooth® connection to an iPhone or iPad. To connect to iOS-based devices more quickly, scan the barcode below to enable Bluetooth® simple pairing so that the passcode-required window will not show up when establishing a connection.
PAGE 74
2564 Barcode Scanner User Guide Auto reconnect on data being scanned Auto reconnect off 2.1.13 UTF8 CONVERSION This function, disabled by default, is only for Russian, Cyrillic, Armenian, and Thai keyboard types.
PAGE 75
Chapter 2 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь 2.2 BT SPP SLAVE For BT SPP Slave, refer to Chapter 3 Setting up a WPAN Connection for related connection settings. 2.2.1 ACTIVATE BT SPP SLAVE MODE Scan this barcode to have the scanner get into SPP Slave Mode. Activate BT SPP, Slave Mode 2.2.2 INTER-FUNCTION DELAY By default, the inter-function delay is set to zero.
PAGE 76
2564 Barcode Scanner User Guide 2) Read the “Decimal Value” barcode on page 251. For example, read “1” and “0” for the scanner to automatically shut down after being idle for 1 second. 3) Read the “Validate” barcode on the same page to complete this setting. ACK/NAK Error Beep Enable Error Beep *Disable Error Beep Note: We suggest enabling the error beep so that you will be notified of such data loss and have the scanner re-read data. 2.2.
PAGE 77
Chapter 2 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь 2.3 BT SPP MASTER As a SPP master device, the scanner will be able to resume connection with the host upon powering on again, as long as the host application is running. If the scanner fails to resume connection, it will try every 5 seconds to re-connect to the host unless you have the scanner read the “Reset Connection” or “Restore System Defaults” barcode. For BT SPP Master, refer 3.2.
PAGE 78
2564 Barcode Scanner User Guide Prefix “0X” to target MAC address Note: Read the “Set Connection” barcode first, and then the “MAC ID” barcode within 10 seconds. Instead of producing the “MAC ID” barcode, you may read the setup barcodes for entering the MAC address.  Read the “Abort” barcode to cancel the operation at any time while reading setup barcodes for the MAC address. If the MAC address has not been completed yet, reading the “Validate” barcode can cancel the operation as well.
PAGE 79
Chapter 2 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь #@CipherLab Enter Setup 88686471166254 Set connection 0X Prefix to the target MAC ID 00d0176f0030 MAC address ID of the target device The concatenation of setup barcodes can be combined to create a single 2D barcode as below: 2D One-Scan Setup Barcode for connecting with a target device Exit SPP Master Mode To stop such re-connection, read “Reset Connection” or “Restore System Defaults” barcode
PAGE 80
2564 Barcode Scanner User Guide 2.3.3 ACK/NAK TIMEOUT By default, the scanner sends data to the host without waiting for an ACK/NAK response before sending more data. Specify a value, ranging from 1 to 99 in units of 0.1 second. If no response within the specified period of time, the scanner will attempt to send the same data two more times. If all three attempts fail without any notification, data loss will occur.
PAGE 81
Chapter 2 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь 2.3.4 SWITCH BETWEEN MASTER/SLAVE MODES After the scanner has established a connection as a SPP slave device, you may have it read the “Activate BT SPP, Master Mode” setup barcode to switch to SPP Master Mode. This will result in easy and reliable re-connection, just like connecting with the cradle. 2.3.
PAGE 82
2564 Barcode Scanner User Guide 2.4 KEYBOARD WEDGE VIA BT CRADLE The Y cable allows you to connect the scanner via the cradle to the keyboard input port of PC and you may join the keyboard as well. The scanned data will be transmitted to the host keyboard port as if it is manually entered via the keyboard. For example, run a text editor on your computer to receive the data.
PAGE 83
Chapter 2 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь 2.4.1 ACTIVATE KEYBOARD WEDGE & SELECT KEYBOARD TYPE When Keyboard Wedge interface is activated, you have to select a keyboard type to complete this setting. Activate Keyboard Wedge & Select Keyboard Type… 1) Read this barcode above to activate Keyboard Wedge and select a keyboard type. 2) Read the “Decimal Value” barcode on page 251. Refer to the table below for the number of desired keyboard type.
PAGE 84
2564 Barcode Scanner User Guide 22 PS55 002-2, 003-2 44 PCAT (Thai) 2.4.2 KEYBOARD SETTINGS          Alphabets Layout Digits Layout Capital Lock Type Capital Lock Setting Alphabets Transmission Digits Transmission Kanji Transmission Alternate Composing Laptop Support Alphabets Layout By default, the alphabets layout is set to normal mode, also known as the standard English layout. Select French or German keyboard layout if necessary.
PAGE 85
Chapter 2 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь US Keyboard Style – Normal QWERTY layout, which is normally used in western countries.  Select “Lower Row” for the “Digits Layout” setting because the upper row is for special characters. French Keyboard Style – AZERTY French layout; see below for French Keyboard Style.  Select “Upper Row” for the “Digits Layout” setting because the lower row is for special characters.
PAGE 86
2564 Barcode Scanner User Guide Digits Layout Select a proper layout that matches Alphabets Layout settings. The scanner will make adjustments according to this setting.
PAGE 87
Chapter 2 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь Capital Lock Type & Setting In order to send the alphabets with correct case, the scanner needs to know the status of Caps Lock on the keyboard. Incorrect settings may result in reversed case of the alphabets being transmitted. Cap Lock Type Description Normal Normal type Capital Lock When enabled, the keys of alphabetic characters will be interpreted as capital letters.
PAGE 88
2564 Barcode Scanner User Guide *Capital Lock OFF Alphabets Transmission By default, the alphabets transmission is case-sensitive, meaning that the alphabets will be transmitted according to their original case, the status of Caps Lock on the keyboard, as well as the Capital Lock setting. Select [Ignore Case] to have alphabets transmitted according to the status of Caps Lock on the keyboard only. Ignore Case *Case-sensitive Refer to 5.1 Letter Case.
PAGE 89
Chapter 2 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь Digits Transmission By default, the alphanumeric keypad is used for transmitting digits. Select “Numeric Keypad” if wishing to use the keys on the numeric keypad. Numeric Key *Alphanumeric Key Note: If selecting “Numeric Keypad”, the Num Lock status of the physical keyboard should be “ON”.
PAGE 90
2564 Barcode Scanner User Guide ALT Composing By default, Alternate key composing is disabled. Select [Yes] to allow emulating Alternate key code of a specific keyboard character. For example, [Alt] + [065] will be sent to host for the character “A” regardless the keyboard type using. Yes *No Laptop Support By default, laptop support value is disabled. It suggests enabling this feature if connecting the wedge cable to a laptop without an external keyboard being inter-connected. Enable *Disable 2.4.
PAGE 91
Chapter 2 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь 2.4.4 INTER-FUNCTION DELAY By default, the inter-function delay is set to zero. Specify a value, ranging from 0 to 254 in units of millisecond, to match the computer response time of the keyboard interface. Such delay time is inserted between every function code (0x01 ~ 0x1F) being transmitted. The longer the delay time is, the slower the transmission speed will be.
PAGE 92
2564 Barcode Scanner User Guide 2.5 RS-232 VIA BT CRADLE Use the RS-232 cable to connect the scanner to the serial port of PC and join the power adaptor to the RS-232 connector. The associated RS-232 parameters must match those configured on the computer. The scanned data will be transmitted to the serial port.
PAGE 93
Chapter 2 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь 2400 bps 1200 bps 600 bps 2.5.3 DATA BITS *8 bits 7 bits 2.5.4 PARITY *No parity Even Odd 2.5.
PAGE 94
2564 Barcode Scanner User Guide 2.5.6 FLOW CONTROL By default, there is no flow control in use. Select the flow control (handshake) method. Options Description No No flow control Scanner Ready The scanner will activate the RTS signal upon powering on. After each good read, the scanner will then wait for the CTS signal to become active. Data will not be sent until the CTS signal becomes active. Data Ready The RTS signal will be activated after each good read.
PAGE 95
Chapter 2 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь 2.5.7 INTER-CHARACTER DELAY By default, the inter-character delay is zero. Specify a value, ranging from 0 to 254 in units of millisecond, to match the computer response time. Such delay time is inserted between every character being transmitted. The longer the delay time is, the slower the transmission speed will be.
PAGE 96
2564 Barcode Scanner User Guide 2.5.9 ACK/NAK TIMEOUT By default, the scanner sends data to the host without waiting for an ACK/NAK response before sending more data. Specify a value, ranging from 1 to 99 in units of 0.1 second. If no response within the specified period of time, the scanner will attempt to send the same data two more times. If all three attempts fail without any notification, data loss will occur.
PAGE 97
Chapter 2 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь 2.6 USB HID VIA BT CRADLE For USB HID, use the USB cable to connect the scanner via cradle to the USB port of PC and connect the power supply cord. Run any text editor on your computer, and the scanned data will be transmitted to the computer. Warning: When the cradle is solely on USB power, the provided current may be insufficient for it to function normally. You must connect the power supply cord.
PAGE 98
2564 Barcode Scanner User Guide 2.6.1 ACTIVATE USB HID & SELECT KEYBOARD TYPE With the USB HID interface activated, you have to select a keyboard type to complete this setting. Activate Direct USB HID & Select Keyboard Type… 1) Read the barcode above to activate USB HID and select a keyboard type. 2) Read the “Decimal Value” barcode on page 251. Refer to the table below for the number of desired keyboard type. 3) Read the “Validate” barcode on the same page to complete this setting.
PAGE 99
Chapter 2 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь 2.6.2 KEYBOARD SETTINGS        Alphabets Layout Digits Layout Capital Lock Type Capital Lock Setting Alphabets Transmission Digits Transmission Kanji Transmission Alphabets Layout By default, the alphabets layout is set to normal mode, also known as the standard English layout. Select French or German keyboard layout if necessary.
PAGE 100
2564 Barcode Scanner User Guide US Keyboard Style – Normal QWERTY layout, which is normally used in western countries.  Select “Lower Row” for the “Digits Layout” setting because the upper row is for special characters. French Keyboard Style – AZERTY French layout; see below for French Keyboard Style.  Select “Upper Row” for the “Digits Layout” setting because the lower row is for special characters. German Keyboard Layout – QWERTZ German layout; see below for German Keyboard Style.
PAGE 101
Chapter 2 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь Digits Layout Select a proper layout that matches the alphabets layout. The scanner will make adjustments according to this setting.
PAGE 102
2564 Barcode Scanner User Guide Capital Lock Type & Setting In order to send the alphabets with correct case, the scanner needs to know the status of Caps Lock on the keyboard. Incorrect settings may result in reversed case of the alphabets being transmitted. Cap Lock Type Description Normal Normal type Capital Lock When enabled, the keys of alphabetic characters will be interpreted as capital letters. However, this does not affect the number or punctuation keys.
PAGE 103
Chapter 2 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь *Capital Lock OFF Alphabets Transmission By default, the alphabets transmission is case-sensitive, meaning that the alphabets will be transmitted according to their original case, the status of Caps Lock on the keyboard, as well as the Capital Lock setting. Select [Ignore Case] to have alphabets transmitted according to the status of Caps Lock on the keyboard only.
PAGE 104
2564 Barcode Scanner User Guide Digits Transmission By default, the alphanumeric keypad is used for transmitting digits. Select “Numeric Keypad” to use the keys on the numeric keypad. Numeric Key *Alphanumeric Key Note: If selecting “Numeric Keypad”, the Num Lock status of the physical keyboard should be "ON". Kanji Transmission Kanji Transmission is supported by the scanner when either Keyboard Wedge or Direct USB HID is selected for the output interface.
PAGE 105
Chapter 2 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь 2.6.3 INTER-CHARACTER DELAY By default, the inter-character delay is set to zero. Specify a value, ranging from 0 to 254 in units of millisecond, to match the computer response time of the keyboard interface. Such delay time is inserted between every character being transmitted. The longer the delay time is, the slower the transmission speed will be.
PAGE 106
2564 Barcode Scanner User Guide 2.6.5 HID CHARACTER TRANSMIT MODE By default, HID interface sends data to the host character by character. You may have the scanner read the “Batch Processing” barcode to process data in batch. Batch Processing *By Character Note: “By Character” transmit mode is required when working with iPhone or iPad. 2.6.6 SPECIAL KEYBOARD FEATURE By default, this interface employs special function codes (0x01 ~ 0x1F) defined in the Keyboard Wedge Table.
PAGE 107
Chapter 2 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь Auto reconnect off 2.6.8 UTF8 CONVERSION This function, disabled by default, is only for Russian, Cyrillic, Armenian, and Thai keyboard types. Enable *Disable 2.6.9 USB POLLING INTERVAL Scan the barcodes below to specify the USB polling interval ranging from 1 to 15ms. It’s set to 10ms by default.
PAGE 108
2564 Barcode Scanner User Guide 2.7 USB VIRTUAL COM VIA BT CRADLE Use the USB cable to connect the scanner via cradle to the USB port of PC and connect the power supply cord. You may run HyperTerminal.exe on your computer, and the scanned data will be transmitted to the computer. Warning: When the cradle is solely on USB power, the current may be insufficient for it to function normally. You must connect the power supply cord.
PAGE 109
Chapter 2 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь 2.7.4 ACK/NAK TIMEOUT By default, the scanner sends data to the host without waiting for an ACK/NAK response before sending more data. Specify a value, ranging from 1 to 99 in units of 0.1 second. If no response within the specified period of time, the scanner will attempt to send the same data two more times. If all three attempts fail without any notification, data loss will occur.
PAGE 110
2564 Barcode Scanner User Guide 2.7.5 USB VCOM VIA CRADLE AUTO-RECONNECTION Users can decide whether to have the scanner automatically reconnect to a paired device after disconnection, and the occasion for reconnecting.
PAGE 111
Chapter 3 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь Chapter 3 SETTING UP A WPAN CONNECTION The scanner can be configured to send data to a host computer wirelessly via the cradle, or to a notebook computer or PDA with Bluetooth® wireless technology. Upon powering up, the scanner will be ready for establishing a WPAN connection. To establish a connection via Cradle after reading “Set Connection” and “Serial No.
PAGE 112
2564 Barcode Scanner User Guide 3.1 CONNECTING VIA CRADLE By default, the interface of the cradle is set to “USB HID”. Use the interface cable to connect the scanner via cradle to PC. You can have up to seven scanners connected to one computer at the same time. Note: If using USB Virtual COM for the first time, you must install its driver beforehand. Driver version 5.4 or later is required. Please remove older versions! 3.1.
PAGE 113
Chapter 3 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь 3.1.2 CHANGE INTERFACE If you want to change the interface cable of the cradle, use one of the scanners to configure the interface-related settings and it will pass the new settings to the cradle, which will then initialize and pass the settings to any other connected scanners. 1) Have the scanner read the “Set Connection” and “Serial Number” labels at the back of the cradle.
PAGE 114
2564 Barcode Scanner User Guide 3.1.3 CONFIGURE RELATED SETTINGS Sniff Mode (Power-saving) By default, this feature is enabled, meaning the scanner will listen to the wireless network at a reduced rate. *Enable Disable 3.2 CONNECTING VIA BLUETOOTH® DONGLE 3.2.1 CHANGE INTERFACE Below is the procedure to configure the scanner before establishing a WPAN connection via Bluetooth® dongle. 1) Have the scanner read the “Enter Setup” barcode to enter the configuration mode.
PAGE 115
Chapter 3 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь 3.2.2 CONFIGURE RELATED SETTINGS Sniff Mode (Power-saving) By default, this feature is enabled, meaning the scanner will listen to the wireless network at a reduced rate. *Enable Disable Note: When connecting more than two scanners to a notebook computer or PDA with Bluetooth® wireless technology, we suggest that you disable the power-saving setting for a more reliable connection.
PAGE 116
2564 Barcode Scanner User Guide 1) Read the barcode above to configure the device name. 2) Read the “Hexadecimal Value” barcode on page 252 for the desired character string. 3) Read the “Validate” barcode to complete this setting.
PAGE 117
Chapter 3 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь Authentication When any changes are made to authentication and PIN code on the scanner side, you will have to remove the scanner from the paired device list (called unpairing) and go through the whole process to re-establish the connection.
PAGE 118
2564 Barcode Scanner User Guide Use random PIN No PIN required Note: When using BT HID, some device driver may not support pre-defined PIN code for authentication. In this case, make sure you have the scanner set to “No PIN or use random PIN” before pairing. While pairing, the host PIN code will be displayed on the computer screen. Have the scanner read the setup barcode “Enter PIN Code in Decimal” or “Enter PIN Code in Hexadecimal” to input the matching PIN code.
PAGE 119
Chapter 3 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь 3.2.3 CONNECT TO DONGLE The procedure goes through associating devices for establishing a WPAN connection, which is pretty much the same except for the software you are using.
PAGE 120
2564 Barcode Scanner User Guide 4. Turn on the scanner with correct WPAN settings, such as select BT SPP or BT HID, broadcasting enabled, authentication enabled, and PIN code specified, etc. Select the check box of [My device is set up and ready to be found] on your computer. 5. Click [Next].
PAGE 121
Chapter 3 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь 6. Wait for a few seconds for the Wizard to search available devices nearby. The scanner will appear with its “serial number” as the device name. You may double-check the “Serial Number” label on the scanner to ensure connecting with the correct scanner. Select the target scanner. If the target scanner does not appear on the list, click [Search Again] to refresh the list.
PAGE 122
2564 Barcode Scanner User Guide 7. Click [Next]. 8. Enter the passkey for authentication, which must be exactly the same as configured for the scanner.
PAGE 123
Chapter 3 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь 9. Click [Next]. Wait for a few seconds for Windows to exchange passkeys.
PAGE 124
2564 Barcode Scanner User Guide Note: When Bluetooth security is enabled without providing a pre-set PIN code, dynamic input of PIN code is supported. 10. Click [Finish].
PAGE 125
Chapter 3 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь 11. Now the target scanner will be listed as shown below. You can have up to seven scanners connected to one computer at the same time.
PAGE 126
2564 Barcode Scanner User Guide BT SPP Connected BT SPP Disconnected 112 Enter Setup
PAGE 127
Chapter 4 CHANGING SYMBOLOGY SETTINGS In this chapter, a brief on the symbology settings is provided for reference. Users can simply scan the setting barcodes below to disable/enable all symbologies. Enable Disable Settings for each particular symbology will be depicted as follows. IN THIS CHAPTER 4.1 Codabar ................................................................... 4.2 Code 25 – Industrial 25 ............................................. 4.3 Code 25 – Interleaved 25 ...........................
PAGE 128
2564 Barcode Scanner User Guide 4.1 CODABAR *Enable Disable 4.1.1 SECURITY LEVEL Security Level renders more decoding accuracy giving consideration to barcodes’ print quality. The scanner allows you to change the CODABAR security level between high or normal level. *Normal High 4.1.2 START/STOP TRANSMISSION Decide whether to include the start/stop characters in the data being transmitted.
PAGE 129
Chapter 4 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь 4.1.3 START/STOP CHARACTER SELECTION Select one of the four different start/stop character pairs – * abcd/abcd abcd/tn*e ABCD/ABCD ABCD/TN*E 4.1.4 CLSI CONVERSION When enabled, the CLSI editing strips the start/stop characters and inserts a space after the first, fifth, and tenth characters of a 14-character Codabar barcode.
PAGE 130
2564 Barcode Scanner User Guide 4.1.5 CODE LENGTH QUALIFICATION To prevent the "short scan" error, define the "Length Qualification" settings to ensure that the correct barcode is read by qualifying the allowable code length.  If "Max/Min Length" is selected, the maximum length and the minimum length must be specified. It only accepts those barcodes with lengths that fall between max/min lengths specified.  If“Fixed Length”is selected, up to 2 fixed lengths can be specified.
PAGE 131
Chapter 4 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь 4.2 CODE 25 – INDUSTRIAL 25 *Enable Disable 4.2.1 SELECT START/STOP PATTERN This decides the readability of all 2 of 5 symbology variants. For example, flight tickets actually use an Industrial 2 of 5 barcode but with Interleaved 2 of 5 start/stop pattern. In order to read this barcode, the start/stop pattern selection parameter of Industrial 2 of 5 should set to "Interleaved 25".
PAGE 132
2564 Barcode Scanner User Guide 4.2.3 TRANSMIT CHECK DIGIT Decide whether to include the check digit in the data being transmitted. *Transmit Industrial 25 Check Digit Do Not Transmit 4.2.4 CODE LENGTH QUALIFICATION To prevent the "short scan" error, define the "Length Qualification" settings to ensure that the correct barcode is read by qualifying the allowable code length.  If "Max/Min Length" is selected, the maximum length and the minimum length must be specified.
PAGE 133
Chapter 4 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь Max. Length (*127) or Fixed Length 1 Min. Length (*4) or Fixed Length 2 3) Read the “Decimal Value” barcode on page 251 for the desired length. 4) Read the “Validate” barcode on the same page to complete this setting.
PAGE 134
2564 Barcode Scanner User Guide 4.3 CODE 25 – INTERLEAVED 25 *Enable Disable 4.3.1 SELECT START/STOP PATTERN This decides the readability of all 2 of 5 symbology variants. For example, flight tickets actually use an Industrial 2 of 5 barcode but with Interleaved 2 of 5 start/stop pattern. In order to read this barcode, the start/stop pattern selection parameter of Industrial 2 of 5 should set to "Interleaved 25".
PAGE 135
Chapter 4 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь 4.3.3 TRANSMIT CHECK DIGIT Decide whether to include the check digit in the data being transmitted. *Transmit Interleaved 25 Check Digit Do Not Transmit 4.3.4 CODE LENGTH QUALIFICATION To prevent the "short scan" error, define the "Length Qualification" settings to ensure that the correct barcode is read by qualifying the allowable code length.
PAGE 136
2564 Barcode Scanner User Guide Max. Length (*126) or Fixed Length 1 Min. Length (*4) or Fixed Length 2 3) Read the “Decimal Value” barcode on page 251 for the desired length. 4) Read the “Validate” barcode on the same page to complete this setting.
PAGE 137
Chapter 4 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь 4.4 CODE 25 – MATRIX 25 Enable *Disable 4.4.1 SELECT START/STOP PATTERN This decides the readability of all 2 of 5 symbology variants. For example, flight tickets actually use an Industrial 2 of 5 barcode but with Interleaved 2 of 5 start/stop pattern. In order to read this barcode, the start/stop pattern selection parameter of Industrial 2 of 5 should set to "Interleaved 25".
PAGE 138
2564 Barcode Scanner User Guide 4.4.3 TRANSMIT CHECK DIGIT Decide whether to include the check digit in the data being transmitted.
PAGE 139
Chapter 4 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь 4.4.4 CODE LENGTH QUALIFICATION To prevent the "short scan" error, define the "Length Qualification" settings to ensure that the correct barcode is read by qualifying the allowable code length.  If "Max/Min Length" is selected, the maximum length and the minimum length must be specified. It only accepts those barcodes with lengths that fall between max/min lengths specified.
PAGE 140
2564 Barcode Scanner User Guide 4.5 CODE 39 *Enable Disable 4.5.1 TRANSMIT START/STOP CHARACTERS Decide whether to verify the check digit. If incorrect, the barcode will not be accepted. Transmit Code 39 Start/Stop Characters *Do Not Transmit 4.5.2 VERIFY CHECK DIGIT Decide whether to verify the check digit. If incorrect, the barcode will not be accepted.
PAGE 141
Chapter 4 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь 4.5.3 TRANSMIT CHECK DIGIT Decide whether to include the check digit in the data being transmitted. *Transmit Code 39 Check Digit Do Not Transmit 4.5.4 STANDARD/FULL ASCII CODE 39 Decide whether to support Code 39 Full ASCII that includes all the alphanumeric and special characters. Code 39 Full ASCII *Standard Code 39 4.5.
PAGE 142
2564 Barcode Scanner User Guide 4.5.6 ASTERISKS (*) AS DATA CHARACTERS Decide whether to take asterisk (*) as part of the data. Enable *Disable 4.5.7 CODE LENGTH QUALIFICATION To prevent the "short scan" error, define the "Length Qualification" settings to ensure that the correct barcode is read by qualifying the allowable code length.  If "Max/Min Length" is selected, the maximum length and the minimum length must be specified.
PAGE 143
Chapter 4 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь Max. Length (*127) or Fixed Length 1 Min. Length (*4) or Fixed Length 2 3) Read the “Decimal Value” barcode on page 251 for the desired length. 4) Read the “Validate” barcode on the same page to complete this setting. 4.6 CODE 93 *Enable Disable 4.6.
PAGE 144
2564 Barcode Scanner User Guide *Enable Max./Min. Length (1~127)… Enable Fixed Length(s)… 2) Read the barcode for Max. Length or Fixed Length 1, and follow steps 3~4. Repeat steps 2~4 for Min. Length or Fixed Length 2. Max. Length (*127) or Fixed Length 1 Min. Length (*4) or Fixed Length 2 3) Read the “Decimal Value” barcode on page 251 for the desired length. 4) Read the “Validate” barcode on the same page to complete this setting.
PAGE 145
Chapter 4 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь 4.7 CODE 128 *Enable Disable 4.7.1 SECURITY LEVEL Security Level renders more decoding accuracy giving consideration to barcodes’ print quality. Decide the security level for reading Code 128 barcodes.
PAGE 146
2564 Barcode Scanner User Guide 4.8 EAN-8 EAN-8 *Enable EAN-8 (No Addon) Disable EAN-8 Addon 2 Enable EAN-8 Addon 2 *Disable EAN-8 Addon 5 Enable EAN-8 Addon 5 *Disable 4.8.1 CONVERT TO EAN-13 Decide whether to expand the read EAN-8 barcode, as well as its addons, into EAN-13.  After conversion, the data follows EAN-13 format and is affected by EAN-13 programming selections (e.g. Check Digit).
PAGE 147
Chapter 4 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь 4.8.2 TRANSMIT CHECK DIGIT Decide whether to include the check digit in the data being transmitted. *Transmit EAN-8 Check Digit Do Not Transmit 4.8.3 CONVERSION FORMAT When converting EAN-8 to EAN-13, you can scan the barcode below to decide conversion in default or GTIN-13 format.
PAGE 148
2564 Barcode Scanner User Guide 4.
PAGE 149
Chapter 4 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь 4.9.1 EAN-13 ADDON MODES Decide whether to enable EAN-13 414/419/434/439 Addon Mode. When enabled, barcodes starting with 414/419/434/439 won’t be decoded if the scanned barcodes do not have the Addon 2 or Addon 5 suffix. EAN-13 414/419/434/439 Addon Mode Enable *Disable Decide whether to enable EAN-13 378/379 Addon Mode.
PAGE 150
2564 Barcode Scanner User Guide Decide whether to enable EAN-13 978 Addon Mode. When enabled, barcodes starting with 978 won’t be decoded if the scanned barcodes do not have the Addon 2 or Addon 5 suffix. EAN-13 978 Addon Mode Enable *Disable Decide whether to enable EAN-13 979 Addon Mode. When enabled, barcodes starting with 979 won’t be decoded if the scanned barcodes do not have the Addon 2 or Addon 5 suffix. EAN-13 979 Addon Mode Enable *Disable Decide whether to enable EAN-13 491 Addon Mode.
PAGE 151
Chapter 4 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь Decide whether to enable EAN-13 529 Addon Mode. When enabled, barcodes starting with 529 won’t be decoded if the scanned barcodes do not have the Addon 2 or Addon 5 suffix. EAN-13 529 Addon Mode Enable *Disable Decide whether to have the scanner buzzer sound two beeps (with tones descending from high to low) when decoding the scanned barcode that doesn’t have the Addon 2 or Addon 5 suffix.
PAGE 152
2564 Barcode Scanner User Guide Convert EAN-13 to ISSN *Do Not Convert 4.9.4 TRANSMIT CHECK DIGIT Decide whether to include the check digit in the data being transmitted. *Transmit EAN-13 Check Digit Do Not Transmit 4.9.5 SECURITY LEVEL Security Level renders more decoding accuracy giving consideration to barcodes’ print quality. Decide the security level for reading EAN-13 barcodes.
PAGE 153
Chapter 4 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь 4.10 GS1-128 (EAN-128) *Enable Disable Note: When this setting is disabled, GS1-128 barcodes used to be taken as Code 128. 4.10.1 TRANSMIT CODE ID Decide whether to include the Code ID (“]C1”) in the data being transmitted. Transmit GS1-128 Code ID *Do Not Transmit 4.10.
PAGE 154
2564 Barcode Scanner User Guide 4.10.3 GS1 FORMATTING Decide whether to enable GS1 formatting for GS1-128. Enable *Disable 4.10.4 APPLICATION ID MARK Decide whether to add an application ID mark (1 character) to the left (AIMark1) or right (AIMark2) of an application ID (AI) for the purpose of labeling it when formatting the GS1 data. AIMark1 AIMark2 1) Read the barcode above to add a mark to the left (AIMark1)/right (AIMark2) of an application ID.
PAGE 155
Chapter 4 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь 4.11 ISBT 128 *Enable Disable 4.11.1 ISBT CONCATENATION Decide whether to decode and concatenate pairs of ISBT barcodes.  Auto-discriminate ISBT Concatenation It decodes and concatenates pairs of ISBT barcodes immediately. If only a single ISBT barcode is present, the scanner must decode 10 times before transmitting its data to confirm that there is no additional ISBT barcode.
PAGE 156
2564 Barcode Scanner User Guide 4.12 MSI Enable *Disable 4.12.1 VERIFY CHECK DIGIT Select one of the three calculations to verify check digit(s) when decoding barcodes. If incorrect, the barcode will not be accepted. *Single Modulo 10 Double Modulo 10 Modulo 10 & 11 4.12.2 TRANSMIT CHECK DIGIT Decide whether to include the check digit(s) in the data being transmitted.
PAGE 157
Chapter 4 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь 4.12.3 CODE LENGTH QUALIFICATION To prevent the "short scan" error, define the "Length Qualification" settings to ensure that the correct barcode is read by qualifying the allowable code length.  If "Max/Min Length" is selected, the maximum length and the minimum length must be specified. It only accepts those barcodes with lengths that fall between max/min lengths specified.
PAGE 158
2564 Barcode Scanner User Guide 4.13 FRENCH PHARMACODE Enable *Disable 4.13.1 TRANSMIT CHECK DIGIT Decide whether to include the check digit in the data being transmitted. *Transmit French Pharmacode Check Digit Do Not Transmit 4.14 ITALIAN PHARMACODE Enable *Disable 4.14.1 TRANSMIT CHECK DIGIT Decide whether to include the check digit in the data being transmitted.
PAGE 159
Chapter 4 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь 4.15 PLESSEY Enable *Disable 4.15.1 CONVERT TO UK PLESSEY Decide whether to change each occurrence of the character 'A' to character 'X' in the decoded data. Convert to UK Plessey *Do Not Convert 4.15.2 TRANSMIT CHECK DIGIT Decide whether to include the two check digits in the data being transmitted.
PAGE 160
2564 Barcode Scanner User Guide 4.
PAGE 161
Chapter 4 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь 4.16.2 GS1 DATABAR OMNIDIRECTIONAL (RSS-14) Enable RSS-14 & RSS Expanded (Groups I, II) *Disable The settings below apply to Group I symbologies only:  GS1 DataBar Omnidirectional  GS1 DataBar Truncated Transmit Code ID Decide whether to include the Code ID in the data being transmitted.
PAGE 162
2564 Barcode Scanner User Guide Do Not Transmit 4.16.3 GS1 DATABAR EXPANDED (RSS EXPANDED) Enable RSS-14 & RSS Expanded (Groups I, II) *Disable The settings below apply to Group II symbologies only:  GS1 DataBar Expanded Transmit Code ID Decide whether to include the Code ID in the data being transmitted.
PAGE 163
Chapter 4 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь 4.16.4 GS1 DATABAR LIMITED (RSS LIMITED) Enable RSS Limited (Group III) *Disable Transmit Code ID Decide whether to include the Code ID in the data being transmitted. *Transmit RSS Limited Code ID Do Not Transmit Transmit Application ID Decide whether to include the Application ID ("01") in the data being transmitted.
PAGE 164
2564 Barcode Scanner User Guide 4.16.5 FIELD SEPARATOR (GS CHARACTER) Decide whether to apply a field separator (to convert the GS control character to human readable character). Enable Field Separator… 1) Read the barcode above to enable field separator. 2) Read the “Hexadecimal System” barcode on page 252 for the desired character string. 3) Read the “Validate” barcode to complete this setting. 4.16.6 GS1 FORMATTING Decide whether to enable GS1 formatting for GS1 DataBar (RSS family).
PAGE 165
Chapter 4 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь 4.16.8 GS1 DATABAR SECURITY LEVEL Security Level renders more decoding accuracy giving consideration to barcodes’ print quality. Decide the security level for reading GS1 DataBar barcodes. *Normal High 4.
PAGE 166
2564 Barcode Scanner User Guide 4.17.1 TELEPEN OUTPUT ASCII/NUMERIC Decide whether to support Telepen in full ASCII code. By default, it supports ASCII mode.  AIM Telepen (Full ASCII) includes all the alphanumeric and special characters.
PAGE 167
Chapter 4 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь 4.
PAGE 168
2564 Barcode Scanner User Guide 4.18.1 CONVERT TO EAN-13 Decide whether to expand the read UPC-A barcode, as well as its addons, into EAN-13.  After conversion, the data follows EAN-13 format and is affected by EAN-13 programming selections (e.g. Check Digit). Convert UPC-A to EAN-13 *Do Not Convert 4.18.2 TRANSMIT SYSTEM NUMBER Decide whether to include the system number in the data being transmitted. *Transmit UPC-A System Number Do Not Transmit 4.18.
PAGE 169
Chapter 4 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь 4.
PAGE 170
2564 Barcode Scanner User Guide 4.19.1 SELECT SYSTEM NUMBER Decide whether to decode the ordinary UPC-E barcodes only or both UPC-E0 and UPC-E1 barcodes.  System number  System number 0 enabled for decoding UPC-E0 barcodes. 1 enabled for decoding UPC-E1 barcodes. System Number 0 & 1 *System Number 0 Only Warning: Because of the way system number 1 is encoded, if both system numbers are enabled, the user might suffer from short scanning UPC-A or EAN-13 barcodes into UPC-E1 barcodes. 4.19.
PAGE 171
Chapter 4 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь 4.19.3 TRANSMIT SYSTEM NUMBER Decide whether to include the system number in the data being transmitted. Transmit UPC-E System Number *Do Not Transmit 4.19.4 TRANSMIT CHECK DIGIT Decide whether to include the check digit in the data being transmitted.
PAGE 172
2564 Barcode Scanner User Guide 4.20 CODE 11 Enable *Disable 4.20.1 VERIFY CHECK DIGIT Select one of the verification when decoding barcodes. If incorrect, the barcode will not be accepted. None Double Single *Auto 4.20.2 TRANSMIT CHECK DIGIT Decide whether to include the check digit in the data being transmitted.
PAGE 173
Chapter 4 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь 4.20.3 SECURITY LEVEL Security Level renders more decoding accuracy giving consideration to barcodes’ print quality. Decide the security level for reading Code 11 barcodes. Normal *High 4.20.4 CODE LENGTH QUALIFICATION To prevent the "short scan" error, define the "Length Qualification" settings to ensure that the correct barcode is read by qualifying the allowable code length.
PAGE 174
2564 Barcode Scanner User Guide Max. Length (*127) or Fixed Length 1 Min. Length (*4) or Fixed Length 2 4) Read the “Validate” barcode on the same page to complete this setting.
PAGE 175
Chapter 4 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь 4.21 COMPOSITE CODE 4.21.1 COMPOSITE CC-A/B Decide whether to enable Composite CC-A/B. Enable Composite CC-A/B *Disable Decide whether to enable GS1 formatting for Composite CC-A/B. When enabled, the field separator and application ID mark will be automatically added to the output data. Enable *Disable 4.21.2 COMPOSITE CC-C Decide whether to enable Composite CC-C.
PAGE 176
2564 Barcode Scanner User Guide 4.21.3 UPC COMPOSITE MODE UPC barcodes can be “linked” with a 2D barcode during transmission as if they were one barcode.  UPC Never Linked Transmit UPC barcodes regardless of whether a 2D barcode is detected.  UPC Always Linked Transmit UPC barcodes and the 2D portion. If the 2D portion is not detected, the UPC barcode will not be transmitted.
PAGE 177
Chapter 4 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь 4.22 2D SYMBOLOGIES 4.22.1 PDF417 *Enable PDF417 Disable 4.22.2 MICROPDF417 Decide whether to enable MicroPDF417 barcodes. Enable MicroPDF417 *Disable 4.22.3 DATA MATRIX Decide whether to enable Data Matrix barcodes. *Enable Data Matrix Disable DATA MATRIX MIRROR Decide whether to decode mirror image Data Matrix barcodes.  Never — do not decode Data Matrix barcodes that are mirror images.
PAGE 178
2564 Barcode Scanner User Guide *Never Always Auto DATA MATRIX INVERSE Decide whether to decode inverse Data Matrix barcodes. *Never Always Auto GS1 FORMATTING Decide whether to enable GS1 formatting for GS1-Data Matrix barcodes. When enabled, the field separator and application ID mark will be automatically added to the output data. Enable *Disable FIELD SEPARATOR Decide whether to apply a field separator (to convert the GS control character to human readable character).
PAGE 179
Chapter 4 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь Specify Field Separator… 1) Read the barcode above to enable field separator. 2) Read the “Hexadecimal System” barcode on page 252 for the desired character string. 3) Read the “Validate” barcode to complete this setting.
PAGE 180
2564 Barcode Scanner User Guide 4.22.4 QR CODE *Enable QR Code Disable QR CODE MIRROR Decide whether to decode mirror image QR Code barcodes.  Never — do not decode QR Code barcodes that are mirror images.  Always — decode only QR Code barcodes that are mirror images.  Auto — decode both mirrored and unmirrored QR Code barcodes. *Never Always Auto QR CODE INVERSE Decide whether to decode inverse QR Code barcodes.
PAGE 181
Chapter 4 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь 4.22.5 MicroQR Enable MicroQR *Disable 4.22.6 MAXICODE *Enable Maxicode Disable 4.22.7 AZTEC *Enable Aztec Disable AZTEC MIRROR Decide whether to decode mirror image Aztec barcodes.  Never — do not decode QR Code barcodes that are mirror images.  Always — decode only QR Code barcodes that are mirror images.  Auto — decode both mirrored and unmirrored QR Code barcodes.
PAGE 182
2564 Barcode Scanner User Guide Auto AZTEC INVERSE Decide whether to decode inverse Aztec barcodes. *Never Always Auto 4.22.
PAGE 183
Chapter 5 DEFINING OUTPUT FORMAT Users can configure the data output format in which the collected data will be output to the host computer. Barcodes read by the scanner will be processed in the following sequence – 1) Perform character substitution on the data scanned. 2) Add Code ID and Length Code to the front of the data:[Code ID][Length Code][Data] 3) Process the whole data in step 2 with user formats. Data is now divided into fields by user specified rules.
PAGE 184
2564 Barcode Scanner User Guide 5.2 CHARACTER SUBSTITUTION Character substitution is performed on every occurrence of the first character specified. If only one character is specified, each time the character occurs in the barcode will be taken away.  The first character will be replaced by the second character(s).  Up to three sets of character substitution can be configured.  If “Keyboard Wedge” or “USB HID” is configured for interface, Key Type and Key Status will then become applicable.
PAGE 185
Chapter 5 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь 5.2.1 SELECT A SET FOR CHARACTER SUBSTITUION Configure Set 1 Configure Set 2 Configure Set 3 1) Read the barcode above to enable character substitution by set. For example, have the scanner read the “Set 1” barcode to configure the first set of character substitution. The scanner will respond with one short beep, high tone, to indicate more setup barcodes are required.
PAGE 186
2564 Barcode Scanner User Guide 5.2.2 SYMBOLOGIES FOR CHARACTER SUBSTITUTION (ALL 3 SETS) By default character substitution will be performed on all symbologies. If the character substitution is not desired with one or more symbologies, read the “Do Not Apply” barcode for each undesired symbologies and all the three sets will be ignored for them.
PAGE 187
Chapter 5 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь Character Substitution for GS1-128 *Apply Do Not Apply Character Substitution for ISBT 128 *Apply Do Not Apply Character Substitution for EAN-8 (No Addon) *Apply Do Not Apply Character Substitution for EAN-8 Addon 2 *Apply Do Not Apply Character Substitution for EAN-8 Addon 5 *Apply Do Not Apply 173 Update
PAGE 188
2564 Barcode Scanner User Guide Character Substitution for EAN-13 (No Addon) *Apply Do Not Apply Character Substitution for EAN-13 Addon 2 *Apply Do Not Apply Character Substitution for EAN-13 Addon 5 *Apply Do Not Apply Character Substitution for French Pharmacode *Apply Do Not Apply Character Substitution for Italian Pharmacode *Apply Do Not Apply 174 Enter Setup
PAGE 189
Chapter 5 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь Character Substitution for Industrial 25 *Apply Do Not Apply Character Substitution for Interleaved 25 *Apply Do Not Apply Character Substitution for Matrix 25 *Apply Do Not Apply Character Substitution for MSI *Apply Do Not Apply Character Substitution for Plessey *Apply Do Not Apply 175 Update
PAGE 190
2564 Barcode Scanner User Guide Character Substitution for GS1 DataBar *Apply Do Not Apply Character Substitution for Telepen *Apply Do Not Apply Character Substitution for UPC-A (No Addon) *Apply Do Not Apply Character Substitution for UPC-A Addon 2 *Apply Do Not Apply Character Substitution for UPC-A Addon 5 *Apply Do Not Apply 176 Enter Setup
PAGE 191
Chapter 5 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь Character Substitution for UPC-E (No Addon) *Apply Do Not Apply Character Substitution for UPC-E Addon 2 *Apply Do Not Apply Character Substitution for UPC-E Addon 5 *Apply Do Not Apply Character Substitution for Code 11 *Apply Do Not Apply Character Substitution for Comopsite CC-A/B *Apply Do Not Apply 177 Update
PAGE 192
2564 Barcode Scanner User Guide Character Substitution for Comopsite CC-C *Apply Do Not Apply Character Substitution for PDF417 *Apply Do Not Apply Character Substitution for MicroPDF417 *Apply Do Not Apply Character Substitution for Data Matrix *Apply Do Not Apply Character Substitution for Maxicode *Apply Do Not Apply 178 Enter Setup
PAGE 193
Chapter 5 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь Character Substitution for QR Code *Apply Do Not Apply Character Substitution for MicroQR *Apply Do Not Apply Character Substitution for Aztec *Apply Do Not Apply Character Substitution for Han Xin *Apply Do Not Apply 179 Update
PAGE 194
2564 Barcode Scanner User Guide 5.3 PREFIX/SUFFIX CODE By default, there is no prefix code, and [ENTER] or [CR] (Carriage Return) is configured to be suffix code. Up to 8 characters can be configured, for example, “Barcode_”, and have the string appear in front of the barcode read, like this – “Barcode_1234567890”.  If “Keyboard Wedge” or “USB HID” is configured for interface, Key Type and Key Status will then become applicable. Decide whether to apply Key Status when select “Normal Key” for Key Type.
PAGE 195
Chapter 5 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь 5.4 CODE ID Up to two characters for Code ID can be configured for each symbology. To make the Code ID configuration easier, the scanner provides five pre-defined Code ID sets that can select one and make necessary changes on it.  If “Keyboard Wedge” or “USB HID” is configured for interface, Key Type and Key Status will then become applicable.
PAGE 196
2564 Barcode Scanner User Guide 5.4.
PAGE 197
Chapter 5 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь Code ID options Set 1 Set 2 Set 3 Set 4 Set 5 Code 39 A C Y M A Italian Pharmacode A C Y M A French Pharmacode A C Y M A Industrial 25 C H H H S Interleaved 25 D I Z I S Matrix 25 E G G G S Codabar F N X N F Code 93 I L L L G Code 128 H K K K C ISBT 128 H K K K C UPC-E S E C E E EAN-8 P B B FF E EAN-13 M A A F E UPC-A J
PAGE 198
2564 Barcode Scanner User Guide *Disable AIM Code ID After applying AIM Code ID, three characters are added in front of the output data. “]” is always the first character. The second (Character) and third (Modifier Character) may vary depending on symbologies. Please refer to the table below. Symbology Character Modifier Character Codabar F 0: Standard Codabar symbol. No special processing.
PAGE 199
Chapter 5 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь Plessey P No options specified. Always transmit 0. Industrial 25 S No options specified. Always transmit 0. Telepen B No options specified. Always transmit 0.
PAGE 200
2564 Barcode Scanner User Guide 5.4.2 CHANGE CODE ID 1) Read the barcode below to change code ID of a specific symbology. 2) Read the “Hexadecimal Value” barcode on page 252 for the desired character string. For example, read “4” and “4” for applying the character [D] for Code ID. 3) Read the “Validate” barcode to complete this setting.
PAGE 201
Chapter 5 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь Configure Code ID for Interleaved 25 Configure Code ID for Matrix 25 Configure Code ID for MSI Configure Code ID for Plessey Configure Code ID for Telepen Configure Code ID for UPC-A Configure Code ID for UPC-E Configure Code ID for Code 11 Configure Code ID for Composite CC-A/B Configure Code ID for Composite CC-C Configure Code ID for PDF417 Configure Code ID for MicroPDF417 187 Update
PAGE 202
2564 Barcode Scanner User Guide Configure Code ID for Data Matrix Configure Code ID for Maxicode Configure Code ID for QR Code Configure Code ID for MicroQR Configure Code ID for Aztec Configure Code ID for Han Xin 5.4.
PAGE 203
Chapter 5 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь 5.5 LENGTH CODE A 4-digit code representing the length of barcode data (character count) can be inserted in front of data being transmitted. Such "Length" code can be individually enabled or disabled for each symbology.
PAGE 204
2564 Barcode Scanner User Guide Length Code for GS1-128 & GS1 DataBar Apply *Do Not Apply Length Code for ISBT 128 Apply *Do Not Apply Length Code for EAN-8 Apply *Do Not Apply Length Code for EAN-13 Apply *Do Not Apply Length Code for French Pharmacode Apply *Do Not Apply 190 Enter Setup
PAGE 205
Chapter 5 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь Length Code for Italian Pharmacode Apply *Do Not Apply Length Code for Industrial 25 Apply *Do Not Apply Length Code for Interleaved 25 Apply *Do Not Apply Length Code for Matrix 25 Apply *Do Not Apply Length Code for MSI 191 Update
PAGE 206
2564 Barcode Scanner User Guide Length Code for Pleesey Apply *Do Not Apply Length Code for Telepen Apply *Do Not Apply Length Code for UPC-A Apply *Do Not Apply Length Code for UPC-E Apply *Do Not Apply Length Code for Code 11 Apply *Do Not Apply 192 Enter Setup
PAGE 207
Chapter 5 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь Length Code for Composite CC-A/B Apply *Do Not Apply Length Code for Composite CC-C Apply *Do Not Apply Length Code for PDF417 Apply *Do Not Apply Length Code for MicroPDF417 Apply *Do Not Apply Length Code for Data Matrix Apply *Do Not Apply 193 Update
PAGE 208
2564 Barcode Scanner User Guide Length Code for Maxicode Apply *Do Not Apply Length Code for QR Code Apply *Do Not Apply Length Code for MicroQR Apply *Do Not Apply Length Code for Aztec Apply *Do Not Apply Length Code for Han Xin Apply *Do Not Apply 194 Enter Setup
PAGE 209
Chapter 5 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь 5.6 MULTI-BARCODE EDITOR The Multi-Barcode Editor allows deciding the output sequence of a concatenation of barcodes. Up to five barcodes can be specified. Enabling this mode will force the scanner to apply Laser mode as the scan mode. For the scanner to concatenate barcodes, the maximum output data length of all the barcodes is 10 KB after configuration.
PAGE 210
2564 Barcode Scanner User Guide 5.6.1 EDIT A CONCATENATION OF BARCODES Edit Output Sequence 1) Read the barcode above to start editing a concatenation of barcodes. 2) Code Type setting – read the “Hexadecimal Value” barcode on page 252 for Code Type of the (first) barcode. For example, read “4” and “1” for Code 39.
PAGE 211
Chapter 5 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь Code Type Symbology Code Type Symbology 3E (>) Han Xin 40 (@) ISBT 128 41 (A) Code 39 42 (B) Italian Pharmacode 43 (C) French Pharmacode 44 (D) Industrial 25 45 (E) Interleaved 25 46 (F) Matrix 25 47 (G) Codabar (NW7) 67 (g) Code 11 48 (H) Code 93 49 (I) Code 128 4A (J) UPC-E0 / UPC-E1 6A (j) Composite CC-C 4B (K) UPC-E with Addon 2 6B (k) PDF417 4C (L) UPC-E with Add
PAGE 212
2564 Barcode Scanner User Guide Note: If not reading 0000 for any length, the 4-digit length must exclude prefix, suffix (0x0d by default), length code, etc. 4) Matching Character setting – read the “Hexadecimal Value” barcode on page 252 for the 1st character that must be found matching in the (first) barcode. For example, read “4” and “1” for matching character “A” as the first character in the barcode or read “00” for any character.
PAGE 213
Chapter 5 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь *Ignore Output Sequence Enforce Output Sequence Apply Output Sequence Warning: When disable the Multi-Barcode Editor later, the scan mode remains unchanged. If Laser mode is not desired, proceed to select a scan mode best suits the application.
PAGE 214
2564 Barcode Scanner User Guide 5.7 REMOVAL OF SPECIAL CHARACTER Specify only 1 character, but it will remove every matching character encountered from the starting position of barcode data until a different character is met. For example, if it is configured to remove the character “0” (hex value is “30”), one or more zeros will be stripped off the barcode data “012345” and “00012345”. However, for barcode data “010333”, only the first zero will be stripped off.
PAGE 215
Chapter 6 APPLYING FORMATS FOR DATA EDITING The scanner allows advanced data editing by applying user-configured editing formats. The whole processed data can be divided into fields by user-specified rules. These fields together with the user-configurable additional fields consist of the data actually sent to the host computer. To apply any editing format, the maximum output data length of a barcode is 7 KB after configuration. When the data length exceeds 7 KB, editing format will not take effect.
PAGE 216
2564 Barcode Scanner User Guide 6.1 ACTIVATING EDITING FORMATS 6.1.1 ACTIVATE EDITING FORMATS Any editing format configured before can directly be applied. If there’s not, users must start with configuring an editing format first, and then activate the editing format when it is desired in use.
PAGE 217
Chapter 6 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь Editing Format 5 Enable *Disable 6.1.2 EXCLUSIVE DATA EDITING By default, only barcodes found meeting with the criteria are processed by the editing formats. Those found not meeting with the criteria are processed normally. When “Exclusive Data Editing” is enabled, all barcodes read by the scanner must be processed by the editing formats.
PAGE 218
2564 Barcode Scanner User Guide 6.
PAGE 219
Chapter 6 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь 6.2.1 SELECT FORMAT TO CONFIGURE Start Programming Format Select one editing format (Format 1~5) and the parameters pertaining to the editing format can then be configured – applicable code type, data length, matching string & location, start position, field adjustment, total number of fields, field settings (field-dividing rule), additional fields, and field transmission sequence.
PAGE 220
2564 Barcode Scanner User Guide 6.2.2 RESTORE DEFAULT FORMAT Select an existing editing format and have the defaults restored. The default settings of an editing format are listed below.
PAGE 221
Chapter 6 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь 6.3 CONFIGURING FORMAT — DEFINE DATA CRITERIA Three applicable conditions can be configured to check whether the data read by the scanner can be processed by the particular editing format. Note: Data editing cannot be performed unless the three conditions are all met. 6.3.
PAGE 222
2564 Barcode Scanner User Guide Editing Format for Codabar *Apply Do Not Apply Editing Format for Code 39 *Apply Do Not Apply Editing Format for Code 93 *Apply Do Not Apply Editing Format for Code 128 *Apply Do Not Apply Editing Format for GS1-128 & GS1 DataBar *Apply Do Not Apply 208 End Programming Format
PAGE 223
Chapter 6 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь Editing Format for ISBT 128 *Apply Do Not Apply Editing Format for EAN-8 *Apply Do Not Apply Editing Format for EAN-8 Addon 2 *Apply Do Not Apply Editing Format for EAN-8 Addon 5 *Apply Do Not Apply Editing Format for EAN-13 *Apply Do Not Apply 209 Update
PAGE 224
2564 Barcode Scanner User Guide Editing Format for EAN-13 Addon 2 *Apply Do Not Apply Editing Format for EAN-13 Addon 5 *Apply Do Not Apply Editing Format for French Pharmacode *Apply Do Not Apply Editing Format for Italian Pharmacode *Apply Do Not Apply Editing Format for Industrial 25 *Apply Do Not Apply 210 End Programming Format
PAGE 225
Chapter 6 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь Editing Format for Interleaved 25 *Apply Do Not Apply Editing Format for Matrix 25 *Apply Do Not Apply Editing Format for MSI *Apply Do Not Apply Editing Format for Plessey *Apply Do Not Apply Editing Format for Telepen *Apply Do Not Apply 211 Update
PAGE 226
2564 Barcode Scanner User Guide Editing Format for UPC-A *Apply Do Not Apply Editing Format for UPC-A Addon 2 *Apply Do Not Apply Editing Format for UPC-A Addon 5 *Apply Do Not Apply Editing Format for UPC-E *Apply Do Not Apply Editing Format for UPC-E Addon 2 *Apply Do Not Apply 212 End Programming Format
PAGE 227
Chapter 6 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь Editing Format for UPC-E Addon 5 *Apply Do Not Apply Editing Format for Code 11 *Apply Do Not Apply Editing Format for Composite CC-A/B *Apply Do Not Apply Editing Format for Composite CC-C *Apply Do Not Apply Editing Format for PDF417 *Apply Do Not Apply 213 Update
PAGE 228
2564 Barcode Scanner User Guide Editing Format for MicroPDF417 *Apply Do Not Apply Editing Format for Data Matrix *Apply Do Not Apply Editing Format for Maxicode *Apply Do Not Apply Editing Format for QR Code *Apply Do Not Apply Editing Format for MicroQR *Apply Do Not Apply 214 End Programming Format
PAGE 229
Chapter 6 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь Editing Format for Aztec *Apply Do Not Apply Editing Format for Han Xin *Apply Do Not Apply 215 Update
PAGE 230
2564 Barcode Scanner User Guide 6.3.2 DATA LENGTH The length must include prefix, suffix (0x0d by default), length code, etc. By default, barcodes of any length (character count) are eligible for data editing.  Specify a value.  When zero is given to both, the scanner will not perform the length qualification. 1) Read the barcode below to specify Max. Length or Min. Length separately, and follow steps 2~3. Max. Length Min. Length 2) Read the “Decimal Value” barcode on page 251 for the desired length.
PAGE 231
Chapter 6 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь 4) Read the barcode to specify the location of the matching string. Location of Matching String… 5) Read the “Decimal Value” barcode on page 251 for the desired location. 6) Read the “Validate” barcode on the same page to complete this setting.
PAGE 232
2564 Barcode Scanner User Guide 6.4 CONFIGURING FORMAT — DEFINE DATA FIELD 6.4.1 START POSITION Data can be divided into fields in one of the following direction –  from head (F1) to tail (F5)  from tail (F1) to head (F5) *From Head From Tail 6.4.2 FIELD ADJUSTMENT Apply equal length to all fields, if necessary. If data is found longer than specified, it will be truncated automatically. When data is found shorter, it will add “Space” (0x20) to field.
PAGE 233
Chapter 6 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь 6.4.3 TOTAL NUMBER OF FIELDS Data can be divided into at most 6 fields; each of them is numbered from F1 to F6 accordingly. However, only F1~F5 can be configured.  The total number of fields must be specified correctly. If three fields are configured for the editing format, the data characters after F3 will be assigned to F4 automatically.
PAGE 234
2564 Barcode Scanner User Guide 6.4.4 FIELD SETTINGS Data eligible for editing formats is divided into fields by user-specified rules – either using the field terminating string or specified field length. By Terminating String Specify the field terminating string. Up to two characters are allowed. The scanner will search for the occurrence of this particular string in the data.  By default, this string will be included in the field. By Length Alternatively, you may simply specify the field length.
PAGE 235
Chapter 6 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь Field 2 Setting 1. Read the barcode below to divide field 2 by a specified terminating string. Select Field Separator to Divide Field 2… 2. Read the “Hexadecimal Value” barcode on page 252 for the desired character string. 3. Read the “Validate” barcode to complete this setting. 4. Read the “Discard Separator” barcode if the field separator is not desired in the field.
PAGE 236
2564 Barcode Scanner User Guide Field 3 Setting 1. Read the barcode below to divide field 3 by a specified terminating string. Select Field Separator to Divide Field 3… 2. Read the “Hexadecimal Value” barcode on page 252 for the desired character string. 3. Read the “Validate” barcode to complete this setting. 4. Read the “Discard Separator” barcode if the field separator is not desired in the field.
PAGE 237
Chapter 6 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь Field 4 Setting 1. Read the barcode below to divide field 4 by a specified terminating string. Select Field Separator to Divide Field 4… 2. Read the “Hexadecimal Value” barcode on page 252 for the desired character string. 3. Read the “Validate” barcode to complete this setting. 4. Read the “Discard Separator” barcode if the field separator is not desired in the field.
PAGE 238
2564 Barcode Scanner User Guide Field 5 Setting 1. Read the barcode below to divide field 5 by a specified terminating string. Select Field Separator to Divide Field 5… 2. Read the “Hexadecimal Value” barcode on page 252 for the desired character string. 3. Read the “Validate” barcode to complete this setting. 4. Read the “Discard Separator” barcode if the field separator is not desired in the field.
PAGE 239
Chapter 6 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь Additional Fields Up to five additional fields can be created for each editing format; each of them is numbered from AF1 to AF5 accordingly.  If “Keyboard Wedge” or “USB HID” is configured for interface, Key Type and Key Status will then become applicable. Decide whether to apply Key Status when “Normal Key” is selected for Key Type.
PAGE 240
2564 Barcode Scanner User Guide 6.4.5 PAUSE FIELD SETTING Pause Field Time Limit the pause time interval (1~16). By default, it is set to 1 second. Pause Field Time 1~16 sec. (*1) 1. Read the barcode above to specify the time interval for the Pause Field. (It is set to 1 by default.) 2. Read the “Decimal Value” barcode on page 251. For example, read “1” and “0” for setting the Pause Field Time to 10 seconds. 3. Read the “Validate” barcode on the same page to complete this setting.
PAGE 241
Chapter 6 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь 6.5 CONFIGURING FORMAT — DEFINE TRANSMISSION SEQUENCE After configuring the data fields and additional fields, you must now program the transmission sequence of these fields that comprise the final data. This field transmission sequence can be assigned in any desired order and fields can be assigned multiple times as well. Note: Up to twelve fields can be assigned.
PAGE 242
2564 Barcode Scanner User Guide Additional Field 2 Additional Field 3 Additional Field 4 Additional Field 5 Pause Field Null Character Field 3) Read the “End” barcode to complete this setting.
PAGE 243
Chapter 6 Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь 6.6 PROGRAMMING EXAMPLES 6.6.1 EXAMPLE I Extract data from the 10th character to the 19th character... The editing format should be configured as follows: 1. Read the “Enter Setup” barcode to enter the Configuration Mode. 2. Read the “Configure Format 1” barcode. 3. Read the “Clear All” and “Code 128” barcodes for applicable code type. 4. Read the “Three Fields” barcode. 5.
PAGE 244
2564 Barcode Scanner User Guide 6.6.2 EXAMPLE II Extract the date code, item number, and quantity information from barcodes. Data in a barcode is encoded like this:    From the 1st character to the 6th character is the date code. From the 7th character to the dash ‘-’ character is the item number. After the dash ‘-’ character is the quantity information.
PAGE 245
SPECIFICATIONS Optical Characteristics 2564 Scan Engine 2D Imager Light Source Aiming pattern: 620~630nm LED Illumination: Warm White LED RF Characteristics WPAN Module Wireless PAN BT Class 2 compliance Coverage (line-of-sight) 100 meters with the cradle Interface Supported    Serial Port Profile (BT SPP)   10 KB for transmit buffer Human Interface Device Profile (BT HID) Cradle Physical Characteristics Memory 4 MB flash for memory mode Switch Tactile switch Indication Triple-col
PAGE 246
2564 Barcode Scanner User Guide Electrical Characteristics Battery Rechargeable Li-ion battery – 3.7 V, 800 mAh Power Adaptor Input AC 100~240 V, 47/63 Hz Output DC 5V, 1A Operating Temperature 0 °C to 40 °C Environmental Characteristics Temperature Humidity (Non-condensing) Operating 0 °C to 50 °C Storage -40 °C to 70 °C Operating 10% to 90% Storage 5% to 95% Resistance Impact Resistance 1.
PAGE 247
Appendix I FIRMWARE UPGRADE You can only upgrade firmware of one scanner at a time. For example, you must turn off each of the rest scanners when there is more than one scanner connected to your computer. Note: In case it fails downloading due to low battery, make sure the targe scanner is loaded with good battery and the battery charge is enough. HOW TO UPGRADE SCANNER FIRMWARE USING THE CRADLE 1) Connect the interface cable, RS-232 or USB, between the cradle and your computer.
PAGE 248
2564 Barcode Scanner User Guide Enter Setup Activate Cradle USB Virtual COM Update 5) Read the following barcodes in sequence for the scanner to enter the download mode. The scanner will respond with beeps to indicate it is ready for downloading. Enter Setup Download 6) Run the download utility “ProgLoad.exe” on the computer. Kernel Program User Program K2564_V*.shx STD2564_V*.shx  For the communication settings, select “RS-232” and the correct COM port for RS-232 or USB Virtual COM interface.
PAGE 249
Appendix I Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь отображаться. Note: The output interface remains unchanged as specified in step 2 (= RS-232 or USB Virtual COM). For RS-232, the baud rate setting is still 115200 bps! USING BLUETOOTH® DONGLE 1) Refer to 3.2.3 Connect to Dongle for the target scanner to accept the connection request from your computer.
PAGE 250
2564 Barcode Scanner User Guide Kernel Program User Program K2564_V*.shx STD2564_V*.shx  For the communication settings, select “RS-232” and the correct COM port for BT SPP interface.  For RS-232, select 115200 bps for baud rate; for USB Virtual COM, ignore the baud rate setting.  For the file option, click [Browse] to select the target file for firmware update.  Click [OK]. 5) After upgrading kernel, you will need to manually restart the scanner.
PAGE 251
Appendix I Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здесь отображаться. HOW TO UPGRADE BT CRADLE FIRMWARE 1) Connect the interface cable, RS-232 or USB, between the cradle and your computer. For USB Virtual COM, you may need to install its driver first! 2) Connect the power supply cord from the cradle to a proper power outlet. 3) Refer to 3.1.1 Connect to Cradle for the target scanner to connect to the cradle.
PAGE 252
2564 Barcode Scanner User Guide 6) Run the download utility “ProgLoad.exe” on your computer. Kernel Program User Program 2564CradleKV*.shx 2564CradleUV*.shx  For the communication settings, select “RS-232” and the correct COM port for RS-232 or USB Virtual COM interface.  For RS-232, select 115200 bps for baud rate; for USB Virtual COM, ignore the baud rate setting.  For the file option, click [Browse] to select the target file for firmware update.  Click [OK].
PAGE 253
Appendix II HOST SERIAL COMMANDS SERIAL COMMANDS D Purpose To disable the scanner. Remarks “D” E Purpose To enable the scanner. Remarks “E” #@ nnnnnn Purpose To configure the scanner. Remarks nnnnnn – the six digits of command parameters. For example, “109952” is to list the current Code ID settings.
PAGE 254
2564 Barcode Scanner User Guide #@TRIGOFF Purpose To disable the software trigger Remarks “0x23” + “0x40” + “0x54” + “0x52” + “0x49” + “0x47” + “0x4f” + “0x46” + “0x46” + “0x0d” #@TRIGON Purpose To enable the software trigger Remarks “0x23” + “0x40” + “0x54” + “0x52” + “0x49” + “0x47” + “0x4f” + “0x4e” + “0x0d” #@RDSN Purpose Read serial number Remarks “0x23” + “0x40” + “0x52” + “0x44” + “0x53” + “0x4E” + “0x0D” #@BEEP, nn Purpose Have the scanner beep as many times as you spec
PAGE 255
Appendix II Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здес For example, ‘#@GLED,09’ is to have the scanner blink for 9 times. “0x23” + “0x40” + “0x47” + “0x4c” + “0x45” + “0x44” + “0x2c” + “0x30” + “0x39” + “0x0d” EXAMPLE You may run HyperTerminal.exe on the host computer to send serial commands to the barcode scanner via RS-232, USB Virtual COM or BT SPP.
PAGE 256
4 Barcode Scanner User Guide Note: (1) For RS-232 or USB Virtual COM, you can only configure the first scanner that connects to the cradle. To identify the scanner, you may send the serial command to have it respond with a beep. (2) For BT SPP, you can configure up to seven scanners at the same time.
PAGE 257
Appendix II Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здес BT CRADLE SETUP BARCODES & SERIAL COMMANDS Normally, you can configure the cradle stand by having a connected scanner read cradle-related setup barcodes. 1) Connect the interface cable, RS-232, Keyboard Wedge or USB, between the cradle and your computer. 2) For USB Virtual COM, you may need to install its driver first! 3) Connect the power supply cord from the cradle to a proper power outlet.
PAGE 258
2564 Barcode Scanner User Guide BT CRADLE SERIAL COMMAND AND EQUIVALENT SETUP BARCODES Config Purpose To configure the cradle. Here is the setup barcode for this serial command: Config Remarks A list of the current settings will be displayed. Run HyperTerminal.exe on your computer and change the settings one by one. DefaultSetting Purpose To restore the default settings.
PAGE 259
Appendix II Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здес USB. Here is the setup barcode for this serial command: UseVariablePort Version Purpose To get the firmware versions. Here is the setup barcode for this serial command: Version GetID Purpose To get MAC ID. Here is the setup barcode for this serial command: GetID Download Purpose To download CPU firmware to the cradle via RS-232 or USB.
PAGE 260
2564 Barcode Scanner User Guide EXAMPLE Without using the scanner to read the above setup barcodes for configuring the cradle, you may run HyperTerminal.exe on the host computer to send serial commands to the cradle via RS-232 or USB. 1) Connect the interface cable, RS-232 or USB, between the cradle and your computer. For USB Virtual COM, you may need to install its driver first! 2) Connect the power supply cord from the cradle to a proper power outlet.
PAGE 261
Appendix III KEYBOARD WEDGE TABLE The table below features special keyboard wedge codes applied to the scanner by default. If you have determined to bypass this special keyboard, please refer to the table on the next page.
PAGE 262
2564 Barcode Scanner User Guide “Bypass” Special Keyboard 0 1 2 3 4 5 6 7 0 SP 0 @ P ` p 1 ! 1 A Q a q 2 " 2 B R b r 3 # 3 C S c s 4 $ 4 D T d t 5 % 5 E U e u 6 & 6 F V f v 7 ' 7 G W g w 8 BS ( 8 H X h x 9 HT ) 9 I Y i y A LF * : J Z j z + ; K [ k { , < L \ l | - = M ] m } E .
PAGE 263
Appendix III Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен зде KEY TYPE & STATUS KEY TYPE If “Keyboard Wedge” or “USB HID” is configured for interface, Key Type and Key Status will then become applicable. *Normal Scan Code KEY STATUS Decide whether or not to change key status when “Normal Key” is selected for Key Type.
PAGE 264
2564 Barcode Scanner User Guide EXAMPLE KEY TYPE = NORMAL For example, if you want to program the character “!” as the prefix code: 1. Read the “Configure Prefix” barcode. 2. Read the “Hexadecimal Value” barcode on page 252 for “2” and “1”. 3. Read the “Validate” barcode to complete this setting. KEY TYPE = SCAN CODE For example, if you want to program the character “a” (= “1C” on the scan code table) as the prefix code: 1. Read the “Configure Prefix” barcode. 2. Read the “Scan Code” barcode. 3.
PAGE 265
Appendix IV NUMERAL SYSTEMS DECIMAL SYSTEM Decimal 0 1 2 3 4 5 6 7 8 9 Validate the Values Validate Update Abort 251
PAGE 266
2564 Barcode Scanner User Guide HEXADECIMAL SYSTEM Hexadecimal 0 1 2 3 4 5 6 7 8 9 A B C D E F 252 Enter Setup
PAGE 267
Appendix IV Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен зде Validate the Values Validate Update Abort 253
PAGE 268
2564 Barcode Scanner User Guide ASCII TABLE 0 0 1 2 3 4 5 6 7 DLE SP 0 @ P ` p 1 SOH DC1 ! 1 A Q a q 2 STX DC2 " 2 B R b r 3 ETX DC3 # 3 C S c s 4 EOT DC4 $ 4 D T d t 5 ENQ NAK % 5 E U e u 6 ACK SYN & 6 F V f v 7 BEL ETB ' 7 G W g w 8 BS CAN ( 8 H X h x 9 HT EM ) 9 I Y i y A LF SUB * : J Z j z B VT ESC + ; K [ k { C FF FS , < L \ l | D CR GS - = M ] m } E SO RS .
PAGE 269
Appendix IV Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен зде ENTERING PIN CODE FOR AUTHENTICATION USE PRESET PIN 1) In the configuration mode, read the barcode below to use a preset PIN for authentication. Use Preset PIN 2) Read one of the barcodes to specify the PIN code, in decimal or hexadecimal. By default, the PIN code is set to “0000”. Maximum 16 characters are allowed.
PAGE 270
2564 Barcode Scanner User Guide DISABLE AUTHENTICATION OR USE RANDOM PIN In the configuration mode, read the barcode below to disable authentication (= No PIN) or use a random PIN for authentication. *No PIN or use random PIN Note: When using BT HID, some device driver may not support pre-defined PIN code for authentication. In this case, make sure you have the scanner set to “No PIN or use random PIN” before pairing. While pairing, the host PIN code will be displayed on the computer screen.
PAGE 271
Appendix V READING DRIVER LICENSES The scanner is capable of reading 2D driver’s licenses and other American Association of Motor Vehicle Administrators (AAMVA) compliant ID cards. For compliant 2D licensed card scanning, it decodes the information embedded in the ID cards to a formatted data. This appendix provides the setup barcodes required while ScanMaster utility provides GUI setup that is oganized and easy-to-use.
PAGE 272
2564 Barcode Scanner User Guide OUTPUT SEQUENCE SETUP The scanner supports arranging the sequences of license embedded data via separators and fields. In order to present data in a consistent format, some barcodes (ex. First Name, Middle Name/Initial, Last Name, Name suffix, Name Prefix, Birth Date and so on) will return data based on the calculated actual data contained in the ID barcode.
PAGE 273
Appendix V Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здес Mailing Address Postal Code Home Address Line1 Home Address Line2 Home Address City Home Address State Home Address Postal Code License ID Number License Class License Restrictions License Endorsements Height (Feet and/or Inches) Height (Centimeters) Update Abort 259
PAGE 274
2564 Barcode Scanner User Guide Weight (Pounds) Weight (Kilograms) Eye Color Hair Color License Expiration Date Birth Date Gender License Issue Date Issue Timestamp Number of Duplicates Medical Codes Organ Donor 260 Enter Setup
PAGE 275
Appendix V Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здес Nonresident Customer ID Social Security Number AKA Birth Date AKA Social Security Name AKA Full Name AKA Last Name AKA First Name AKA Middle Name/Initial AKA Name Suffix AKA Name Prefix Weight Range Update Abort 261
PAGE 276
2564 Barcode Scanner User Guide Document Discriminator Country Federal Commission Codes Place of Birth Audit Information Inventory Control Race/Ethnicity Std Vehicle Class Std Restrictions Std Endorsements Class Description Endorsement Description 262 Enter Setup
PAGE 277
Appendix V Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здес Restrictions Description Permit Class Permit Expiration Date Permit ID Number Permit Issue Date Permit Restrictions Permit endorsements Issuer ID Number Family Name Truncation First Name Truncation Middle Name Truncation Update Abort 263
PAGE 278
2564 Barcode Scanner User Guide SEPARATORS AND FIELDS Define the separators that separate fields during the transmission sequence of data scanning. In addition to the built-in data elements, you can also specify up to 5 Additional Fields with 4 bytes characters. Program the transmission sequence by reading the desired fields as additional fields. Note: Up to 5 separators can be assigned. Separator 1 (1 byte) *“Space” Separator 2 (1 byte) *“Enter” Separator 3 (1 byte) *“,” Separator 4 (1 byte) *“.
PAGE 279
Appendix V Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен здес EDIT SEPARATORS All the driver license fields can be split with a pre-selected separator, for example, “-” as First Name-Last Name or “:” as First Name:Last Name. Edit Separator 1 Edit Separator 2 Edit Separator 3 Edit Separator 4 Edit Separator 5 1) Read the barcode above to apply separator to driver license information separately, and follow steps 2~3.
PAGE 280
2564 Barcode Scanner User Guide EDIT FIELDS Up to five additional fields can be created for each editing format; each of them is numbered from Additional 1 to Additional 5 accordingly.  If “Bluetooth® HID” or “USB HID” is configured for interface, Key Type and Key Status will then become applicable. You may decide whether or not to apply Key Status when “Normal Key” is selected for Key Type. Key Type Key Status Scan Code Up to 2 scan code values are allowed.
PAGE 281
Appendix VI Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен зде Appendix VI KEYBOARD TYPE ONE-SCAN BARCODE BLUETOOTH HID PCAT (US) PCAT (French) PCAT (German) PCAT (Italian) PCAT (Swedish) PCAT (Norwegian) PCAT (UK) PCAT (Belgium) Update Abort 267
PAGE 282
2564 Barcode Scanner User Guide PCAT (Spanish) PCAT (Portuguese) PS55 A01-2 (Japanese) User-defined table PCAT (Turkish) PCAT (Hungarian) PCAT (Swiss German) PCAT (Danish) PCAT (Russian) 268 Enter Setup
PAGE 283
Appendix VI Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен зде PCAT (Cyrillic on Russian) PCAT (Armenian) PCAT (Thai) Update Abort 269
PAGE 284
2564 Barcode Scanner User Guide KEYBOARD WEDGE (CRADLE) PCAT (US) PCAT (French) PCAT (German) PCAT (Italian) PCAT (Swedish) PCAT (Norwegian) PCAT (UK) PCAT (Belgium) PCAT (Spanish) 270 Enter Setup
PAGE 285
Appendix VI Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен зде PCAT (Portuguese) PS55 A01-1 PS55 A01-2 (Japanese) PS55 A01-3 PS55 001-1 PS55 001-81 PS55 001-2 PS55 001-82 PS55 001-3 Update Abort 271
PAGE 286
2564 Barcode Scanner User Guide PS55 001-8A PS55 002-1, 003-1 PS55 002-81, 003-81 PS55 002-2, 003-2 PS55 002-82, 003-82 PS55 002-3, 003-3 PS55 002-8A, 003-8A IBM 3477 Type 4 (Japanese) PS2-30 272 Enter Setup
PAGE 287
Appendix VI Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен зде IBM 34XX/319X, Memorex Telex 122 Keys User-defined table PCAT (Turkish) PCAT (Hungarian) PCAT (Swiss German) PCAT (Danish) PCAT (Russian) PCAT (Cyrillic on Russian) PCAT (Armenian) Update Abort 273
PAGE 288
2564 Barcode Scanner User Guide PCAT (Thai) 274 Enter Setup
PAGE 289
Appendix VI Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен зде REMOTE USB HID (CRADLE) PCAT (US) PCAT (French) PCAT (German) PCAT (Italian) PCAT (Swedish) PCAT (Norwegian) PCAT (UK) PCAT (Belgium) PCAT (Spanish) Update Abort 275
PAGE 290
2564 Barcode Scanner User Guide PCAT (Portuguese) PS55 A01-2 (Japanese) User-defined table PCAT (Turkish) PCAT (Hungarian) PCAT (Swiss German) PCAT (Danish) PCAT (Russian) PCAT (Cyrillic on Russian) 276 Enter Setup
PAGE 291
Appendix VI Ошибка! Используйте вкладку "Главная" для применения Heading 1 к тексту, который должен зде PCAT (Armenian) PCAT (Thai) Update Abort 277