Product Info

ManualsBrandsCipherLab ManualsPOS EquipmentBT Barcode Scanner

1663 A Barcode Scanner

Setup barcodes included.

Version 1.09

Summary of content (233 pages)

PAGE 1
663 A Barcode Scanner Setup barcodes included. Version 1.
PAGE 2
Copyright © 2012~2018 CIPHERLAB CO., LTD. All rights reserved The software contains proprietary information of CIPHERLAB CO., LTD.; it is provided under a license agreement containing restrictions on use and disclosure and is also protected by copyright law. Reverse engineering of the software is prohibited. Due to continued product development this information may change without notice.
PAGE 3
IMPORTANT NOTICES
PAGE 4
FOR USA This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
PAGE 5
This device has also been evaluated and shown compliant with the IC RF Exposure limits under portable exposure conditions. (antennas are less than 20 cm of a person's body). Cet appareil est conforme avec Industrie Canada exemptes de licence RSS standard(s). Son fonctionnement est soumis aux deux conditions suivantes : (1) cet appareil ne doit pas causer d'interférence et (2) cet appareil doit accepter toute interférence, notamment les interférences qui peuvent affecter son fonctionnement.
PAGE 6
FOR HAND-HELD PRODUCT WITH RF FUNCTIONS The 1663 A unit (FCC ID: Q3N-1663A) complies with FCC radiation exposure limits set forth for uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65. The unit has very low level of RF energy that it is deemed to comply without testing of specific absorption ratio (SAR). The 3610 Aunit (FCC ID: Q3N-3610A) complies with FCC radiation exposure limits set forth for an uncontrolled environment.
PAGE 7
RELEASE NOTES
PAGE 8
PAGE 9
CONTENTS IMPORTANT NOTICES ........................................................................................................- 3 For USA........................................................................................................................................ - 4 For Canada ................................................................................................................................. - 4 For Hand-held Product with RF Functions ............................................
PAGE 10
1663 A Barcode Scanner User Guide 1.3.1 Good Read LED.......................................................................................................... 30 1.3.2 Good Read LED Duration ....................................................................................... 30 1.4 Beeper .................................................................................................................................... 31 1.4.1 Beeper Volume .............................................................
PAGE 11
1663 Barcode Scanner User Guide 2.1.2 Reset Connection ...................................................................................................... 58 2.1.3 Keyboard Settings .................................................................................................... 59 2.1.4 Inter-Character Delay ............................................................................................. 64 2.1.5 Inter-Function Delay ......................................................................
PAGE 12
1663 A Barcode Scanner User Guide 2.7 Direct USB Virtual COM ................................................................................................... 99 2.7.1 Activate USB Virtual COM...................................................................................... 99 2.7.2 Avtivate USB Virtual COM_CDC .......................................................................... 99 2.7.3 Inter-Function Delay .......................................................................................
PAGE 13
1663 Barcode Scanner User Guide 4.7 Code 93 ...............................................................................................................................131 4.8 Code 128 .............................................................................................................................131 4.8.1 Code 128 Security Level ......................................................................................131 4.9 EAN-8 ................................................................
PAGE 14
1663 A Barcode Scanner User Guide 4.20.2 Convert to UPC-A .................................................................................................155 4.20.3 System Number Transmission ........................................................................156 4.20.4 Transmit Check Digit ..........................................................................................156 4.21 Code 11 ...........................................................................................................
PAGE 15
1663 Barcode Scanner User Guide SPECIFICATIONS .................................................................................................................
PAGE 16
PAGE 17
INTRODUCTION CipherLab’s small-form-factor 1600 Series Barcode Scanners are specifically designed to answer the mobile demands. The palm-sized scanners are designed to help accelerate productivity while lowering the total cost of ownership. Intensive data collection jobs are made easier with fast, accurate barcode scanning in various working environments, especially in small businesses.
PAGE 18
1663 Barcode Scanner User Guide GET FAMILIARIZED WITH 1663 A AND 3610 INSTALL THE BATTERY INTO 1663 A 1) Hold the scanner face down in one hand, press the battery cover, and slide the battery cover. 2) Remove the battery cover. 3) Push battery lock to unlocked position. 4) Insert the battery into the battery compartment.  Install the supplied 3.6V/975mAh Li-ion battery into the battery compartment. 5) Push battery lock to lock the battery firmly. 6) Replace the battery cover.
PAGE 19
錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 Note: (1) To turn off the scanner, press the [Power/Delete] key for 2 seconds. The scanner will respond with two short beeps (high tone) and the LED will become solid red. Release the key. Otherwise, let the scanner turn off automatically in specific circumstances. Refer to settings of “Auto Power Off”. (2) For shipping and storage purposes, remove the battery from the scanner. This will keep the batteries in good condition for future use.
PAGE 20
1663 Barcode Scanner User Guide CHARGE THE BATTERY VIA CHARGER The battery charger is provided for charging the battery outside of the scanner. You may purchase the charger separately. It takes approximately 3 hours to charge the battery to full. Note: Battery charging stops when the temperature drops below 0°C or exceeds 40°C. It is recommended to charge the battery at room temperature (18°C to 25°C) for optimal performance. 1) Insert the battery. 2) Connect the power supply cord to the charger.
PAGE 21
錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 USE 3610 The CipherLab Dongle (3610) is specifically designed for the scanner to communicate with a host computer cordless. The connection between the scanners and 3610 is made easy and reliable. Refer to 3.1.1 Connect to 3610. There is one LED indicator provided for communications status.
PAGE 22
1663 Barcode Scanner User Guide INSIDE THE PACKAGE The items included in the package may be different, depending on your order. Save the box and packaging material for future use in case you need to store or ship the scanner.        1663 A Scanner CipherLab Dongle (3610) Optional Rechargeable Li-ion Battery Pack Direct USB Cable Wristband Setup Cards Quick Start Guide PRODUCT HIGHLIGHTS     Small-form-factor and built tough to survive drop test.
PAGE 23
錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 SYMBOLOGIES SUPPORTED Most of the popular barcode symbologies are supported, as listed below. Each can be individually enabled or disabled. The scanner will automatically discriminate and recognize all the symbologies that are enabled. Refer to Chapter 4 Change Symbology Settings for details of each symbology.
PAGE 24
1663 Barcode Scanner User Guide GS1 DataBar (RSS) GS1 DataBar Omnidirectional (RSS-14) Disabled GS1 DataBar Truncated Disabled GS1 DataBar Stacked Disabled GS1 DataBar Stacked Omnidirectional Disabled GS1 DataBar Limited (RSS Limited) Disabled GS1 DataBar Expanded (RSS Expanded) Disabled GS1 DataBar Expanded Stacked Disabled Code 11 Disabled 8 Enter Setup
PAGE 25
QUICK START The configuration of the scanner can be done by reading the setup barcodes contained in this manual or via the ScanMaster software. This section describes the procedure of configuring the scanner by reading the setup barcodes and provides some examples for demonstration. Configuration Mode 1) Hold down the [Power/Delete] key for 2 seconds to turn on the scanner. It will respond with a long beep and its LED will come on-off. 2) Read the “Enter Setup” barcode.
PAGE 26
1663 A Barcode Scanner User Guide Working Mode Upon powering up, the scanner will try to establish a connection with 3610 or a computer with Bluetooth® wireless technology. Refer to Chapter 3 - Set up a WPAN Connection for details. The connection between the scanners and 3610 is made easy and reliable. Now, it also supports Bluetooth® SPP Master Mode as an alternative. Refer to 2.3 Bluetooth® SPP Master.
PAGE 27
錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 ENTER CONFIGURATION MODE For the scanner to enter the configuration mode, read the "Enter Setup" barcode, which can be located at the bottom of almost every even page of this manual.  The scanner will respond with six beeps and its LED indicator will become flashing red after reading the barcode. Enter Setup For configuring scanner parameters, see “Read a Setup Barcode” below.
PAGE 28
1663 A Barcode Scanner User Guide DEFAULT SETTINGS SAVE USER SETTINGS AS DEFAULTS For the scanner to keep the customized settings as user defaults, you must read the “Save as User Defaults” barcode. This is a normal setup barcode, and the scanner will respond with two beeps (low-high tone).  After reading the “Update” barcode, the current settings will be saved as user defaults.
PAGE 29
錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 READ A SETUP BARCODE CONFIGURE PARAMETERS For most of the scanner parameters, only one read is required to set them to new values. The scanner will respond with two beeps (low-high tone) when each parameter is set successfully. Refer to Create One-Scan Setup Barcodes. But for a number of special parameters, multiple reads are required to complete the setting.
PAGE 30
1663 A Barcode Scanner User Guide The example below shows how to save your settings as “User Default” so that you may restore user defaults at a later time: Steps Action LED/Beeper Response when Successful 1) Power on the scanner… The scanner will respond with a long beep (high tone) and its LED indicator will become solid red and go off. 2) Enter the Configuration Mode… The scanner will respond with six beeps (high-low tone repeats three times), and its LED indicator will be flashing red.
PAGE 31
錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 The example below shows how to set numeric parameters: Steps Action LED/Beeper Response when Successful 1) Power on the scanner... The scanner will respond with a long beep (high tone) and its LED indicator will become solid red and go off. 2) Enter the Configuration Mode… The scanner will respond with six beeps (high-low tone repeats three times), and its LED indicator will become flashing red. 3) Read a Setup barcode...
PAGE 32
1663 A Barcode Scanner User Guide The example below shows how to set string parameters: Steps Action LED/Beeper Response when Successful 1) Power on the scanner... The scanner will respond with a long beep (high tone) and its LED indicator will become solid red and go off. 2) Enter the Configuration Mode… The scanner will respond with six beeps (high-low tone repeats three times), and its LED indicator will become flashing red. 3) Read a Setup barcode...
PAGE 33
錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 LIST THE CURRENT SETTINGS The current settings of all scanner parameters can be sent to the host computer for user inspection. The listing includes pages as shown below. You can select the page of interest by having the scanner read the “List Page x” barcode. The scanner will respond with two beeps (low-high tone) and send the selected page to the host immediately.
PAGE 34
1663 A Barcode Scanner User Guide List settings regarding Editing Format 4 List Page 11 List settings regarding Editing Format 5 List Page 12 List settings regarding Power and Time List Page 13 18 Enter Setup
PAGE 35
錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 CREATE ONE-SCAN SETUP BARCODES The fact is most of the scanner parameters require only one read for setting new values. To facilitate configuring the scanner, you may create One-Scan setup barcodes for use.
PAGE 36
1663 A Barcode Scanner User Guide 20 Enter Setup
PAGE 37
Chapter 1 UNDERSTANDING THE BARCODE SCANNER This chapter explains the features and usage of the barcode scanner. IN THIS CHAPTER 1.1 Battery ...................................................................... 21 1.2 Memory ..................................................................... 26 1.3 LED Indicator ............................................................. 29 1.4 Beeper....................................................................... 31 1.5 Vibrator ...............................
PAGE 38
1663 A Barcode Scanner User Guide 1.1.1 POWER LEVEL Scan the barcode below to get the battery capacity information with each increment of 20 in percentage terms. Remaining Battery Capacity 1.1.2 HOW TO OPERATE THE SCANNER Turn on the scanner… Press the [Power/Delete] key for 2 seconds. The scanner will respond with a long beep (high tone), and its LED indicator will become solid red and go off. Turn off the scanner… Press the [Power/Delete] key for 2 seconds.
PAGE 39
Chapter 1 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 1.1.3 AUTO POWER OFF & POWER-SAVING The scanner will stay active at power-on, which may be followed by a transition from full CPU speed to low CPU speed (Power-Saving) to auto shutdown (Auto Power Off).  Power-Saving (1~254 min.; 0= Disable): By default, it is set to stand by at full-speed for 2 minutes before it enters low-speed mode. If this feature is not desired, set it to 0.  Auto Power Off (1~254 min.
PAGE 40
1663 A Barcode Scanner User Guide After establishing a WPAN connection successfully… 1) Once a WPAN connection is established successfully, the scanner will stay active for a specified period of time (2 minutes by default) for data transmission. Its CPU is running at full speed, and the LED is flashing blue (On/Off ratio 0.02 s: 3 s). 2) If it is idle within 2 minutes, the scanner will become inactive to save power for the remaining period of time (the specified value minus 2 minutes).
PAGE 41
Chapter 1 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 Auto Off after 0~254 min. (*10) 1) Read the barcode above to specify the time interval in minutes before the scanner automatically turns off. 2) Read the “Decimal Value” barcode on page 錯誤! 尚未定義書籤。. For example, read “1” and “5” for the scanner to automatically turn off after being idle for 15 minutes. 3) Read the “Validate” barcode on the same page to complete this setting.
PAGE 42
1663 A Barcode Scanner User Guide 1.2 MEMORY The scanned data can be sent to a host computer immediately via the WPAN connection or stored in flash memory when the scanner is set to Memory mode. 1.2.1 TRANSMIT BUFFER By default, the transmit buffer is enabled and ready for use when the scanner is out of range. Upon reading a barcode successfully within range, the scanner responds with one short beep (high tone) and its LED indicator becomes solid green and goes off.
PAGE 43
Chapter 1 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 Enable *Disable Warning: No real-time connection is allowed unless the memory mode is disabled. Memory Data Delay You may set a delay between each data record while transmitting data back to the host. *None 250 ms 500 ms 1 sec 2 sec 3 sec 5 sec 8 sec Send Data When the memory is used up, the scanner will respond with two short beeps (high-low tone) as a warning.
PAGE 44
1663 A Barcode Scanner User Guide Data” barcode below. 1663 A can send data via “Direct USB” interface once the computer has found the USB connection. Refer to 1.14 Use Direct USB Cable. Because the time-out value is set to 0 by default, connect the cable before having the scanner read the “Send Data” barcode. Otherwise, the scanner will try to temporarily resume the previous WPAN connection with the host, if there is any.
PAGE 45
Chapter 1 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 1.3 LED INDICATOR The triple-color LED on top of the scanner is used to provide user feedback. For example, the LED becomes solid red and goes off upon powering on or running out of transmit buffer. You may tell the difference by the beeps – you will hear a long beep of high tone when powering on the scanner, and a long beep of low tone when the transmit buffer becomes full.
PAGE 46
1663 A Barcode Scanner User Guide 1.3.1 GOOD READ LED *Enable Good Read LED Disable Good Read LED 1.3.2 GOOD READ LED DURATION By default, the Good Read LED stays on for 40 milliseconds. Specify a value, ranging from 1 to 254 in units of 10 milliseconds. Good Read LED Time-out after 0.01~2.54 sec. (*40 ms) 1) Read the barcode above to specify the time interval before the Good Read LED goes off. 2) Read the “Decimal Value” barcode on page 錯誤! 尚未定義書籤。.
PAGE 47
Chapter 1 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 1.4 BEEPER The scanner has a buzzer to provide user feedback in various operating conditions.
PAGE 48
1663 A Barcode Scanner User Guide 1.4.
PAGE 49
Chapter 1 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 1.4.
PAGE 50
1663 A Barcode Scanner User Guide 1.4.3 LOW BATTERY ALARM By default, the built-in battery alarm will sound when the battery charge gets low. In order to prevent data loss, it is advised to replace the battery immediately when hearing two short beeps (high tone). Disable *Enable 1.5 VIBRATOR 1.5.1 GOOD READ VIBRATOR Enable Good Read Vibrator *Disable Good Read Vibrator 1.5.2 GOOD READ VIBRATOR DURATION By default, the Good Read Vibrator stays on for 1 second.
PAGE 51
Chapter 1 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 1.6 SEND “NR” TO HOST The scanner can send an “NR” string to the host to notify a No Read event.
PAGE 52
1663 A Barcode Scanner User Guide 1.7 SCAN MODES Different scan modes are supported – select the scan mode that best suits the requirements of a specific application. Refer to the comparison table below.
PAGE 53
Chapter 1 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 1.7.1 CONTINUOUS MODE The scanner is always scanning.  After a successful decoding, the removal of barcode is required. It is not allowed to proceed to decode until the decoding delay time has passed.  To decode the same barcode repeatedly, move away the barcode and put it back again and again for scanning. Note: Refer to “Delay between Re-read”. Continuous Mode Decoding Delay Set the time interval between each decoding. *Disable 0.
PAGE 54
1663 A Barcode Scanner User Guide 1.7.3 LASER MODE The scanner will start scanning once the trigger is held down.  The scanning won't stop until (1) a barcode is decoded, (2) the pre-set timeout expires, or (3) you release the trigger. Note: Refer to “Scanning Timeout”. *Laser Mode 1.7.4 AUTO OFF MODE The scanner will start scanning once the trigger is pressed.  The scanning won't stop until (1) a barcode is decoded, and (2) the pre-set timeout expires. Note: Refer to “Scanning Timeout”.
PAGE 55
Chapter 1 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 1.7.6 ALTERNATE MODE The scanner will start scanning once the trigger is pressed  The scanning won't stop until you press the trigger again. Alternate Mode 1.7.7 AIMING MODE The scanner will aim at a barcode once the trigger is pressed, and start scanning when the trigger is pressed again within one second.  The scanning won't stop until (1) a barcode is decoded, and (2) the pre-set timeout expires.
PAGE 56
1663 A Barcode Scanner User Guide 1.7.8 MULTI-BARCODE MODE The scanner will be scanning as long as the trigger is held down, capable of decoding one single barcode, as well as multiple unique barcodes one at a time. While decoding a bunch of unique barcodes, if a barcode is decoded twice, its subsequent decoding will be ignored and the scanner is expecting another unique barcode.  The scanning won't stop until you release the trigger.
PAGE 57
Chapter 1 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 1.8 SCANNING TIMEOUT Specify the scanning time interval (1~254 sec.; 0= Disable) when the scan mode is set to any of the following –     Laser mode Auto Off mode Auto Power Off mode Aiming mode Scanner Time-out after 0~254 sec. (*10) 1) Read the barcode above to specify the time interval in seconds before the scan engine times out. 2) Read the “Decimal Value” barcode on page 錯誤! 尚未定義書籤。.
PAGE 58
1663 A Barcode Scanner User Guide 1.
PAGE 59
Chapter 1 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 1.10 READ REDUNDANCY FOR ALL SYMBLOGIES Select the level of reading security. For example,  If "No Redundancy" is selected, one successful decoding will make the reading valid and induce the "READER Event".  If "Two Times" is selected, it will take a total of three consecutive successful decoding of the same barcode to make the reading valid.
PAGE 60
1663 A Barcode Scanner User Guide 1.11 ADDON SECURITY FOR UPC/EAN BARCODES The scanner is capable of decoding a mix of UPC/EAN barcodes with and without addons. The read redundancy (0~30 times) allows changing the number of times to decode a UPC/EAN barcode before transmission. The more redundancy selected, the higher the reading security is, and thus, the slower the reading speed becomes. Note: UPC/EAN Addon 2 and Addon 5 must be enabled individually for this setting to take effect.
PAGE 61
Chapter 1 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 1.13 EFFECTIVE DECODING AREA By default, the effective decoding area is 100% covered by the scanned area. However, you may narrow down the decoding area to prevent reading the wrong barcode when a number of barcodes are printed closely. The scanner will only read barcodes that appear in the effective decoding area. Read the barcode “Centering On” and specify the percentage to narrow down the decoding area.
PAGE 62
1663 A Barcode Scanner User Guide 1.13.
PAGE 63
Chapter 1 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 1.14 USE DIRECT USB CABLE 1663 A supports Direct USB interface for charging the battery and/or sending data to the host in memory mode. Refer to 1.2.2 Memory Mode. Note: The scanner will not function when it is solely on USB power and without a battery loaded. 1.14.
PAGE 64
1663 A Barcode Scanner User Guide 1.15 PAGER BEEP DURATION Paging function is only activated when 1663 A is in Power-Saving mode. 1663 A can be woken up via receiving any Bluetooth® status command by pressing a key on the host keyboard. The buzzer will continuously sound two short high tone beeps until the power key is pressed on the scanner or the timeout is reached, and the scanner re-enters power saving mode. By default, the pager beep duration is 5 seconds. Specify a value, ranging from 0 to 15.
PAGE 65
Chapter 1 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 1.16 TIME STAMP Specify time stamp format added to the prefix or suffix of a data. can be configured: Up to three settings  No Time Stamp  Add Time Stamp in front of data  Add Time Stamp to the end of data If added in front of data, it means prior to the prefix field. Alternatively, to the end of data. No Time Stamp *Disable Add Time Stamp in front of Data Add Time Stamp to the end of Data 1.16.
PAGE 66
1663 A Barcode Scanner User Guide Date Output *Enable Date Output Disable Hour Output *Enable Hour Output Diable Minute Output *Enable Minute Output Disalbe Second Output *Enable Second Output Diable 50 Enter Setup
PAGE 67
Chapter 1 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 Decoding Data and Time Year Setup Date Setup Time Setup 1) Read the barcode above to apply time or date code separately, and follow steps 2~3. 2) Read the “Decimal Value” barcode on page 錯誤 ! 尚未定義書籤。 for the desired character string. For example: Year: Read “2”, “0”, “1”, “1” for the year setting as year=2011. Date: Read “1”, “1”, ”2”, “0” for the date setting as date=Nov.20. Time: Read “1”, “8”, “5”, “9” for the time setting as time=18:59.
PAGE 68
1663 A Barcode Scanner User Guide 3) Read the “Validate” barcode on the same page to complete this setting. 1.16.3 DATE FORMAT The date format includes year, month and day.
PAGE 69
Chapter 1 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 1.17 HARDWARE RESET 1.17.1 RESTORE SYSTEM DEFAULTS In addition to using the “Restore System Defaults” barcode, the following procedure using key combinations can be used to restore the system defaults during operation. 1) Hold down the [Power/Delete] key. 2) When the scanner responds with two short beeps (high tone), press the [Trigger] key for 5 seconds. The scanner LED indicator becomes solid red and then goes off.
PAGE 70
1663 A Barcode Scanner User Guide 1.18 SERIAL NUMBER STAMP Decide whether to add the device serial number in front of the data transmitted. Add serial number in front of data *Disable 1.18.1 SEPARATOR BETWEEN SERIAL NUMBER STAMP AND DATA Scan the barcode below to specify the separator character between device serial number and the accompanying data. By default, the separactor is a comma symbol. Specify the separator character 1) Read the barcode above to specify a separator character.
PAGE 71
Chapter 2 SELECTING OUTPUT INTERFACE In order to establish a proper connection between host computer and the scanner, we suggest following these instructions – 1) Install battery and hold down the [Power/Delete] key for 2 seconds to turn on the scanner. 2) Read the “Enter Setup” barcode to enter the configuration mode. 3) Read the associated barcodes to activate the desired interface. See the following sections for output interfaces supported. 4) Read the barcodes for related settings.
PAGE 72
1663 A Barcode Scanner User Guide 2.1 BLUETOOTH® HID For Bluetooth® HID, refer to Chapter 3 – Setting up a WPAN Connection for related connection settings. The scanned data will be transmitted to the computer. To capture the data run any text editor on your computer.
PAGE 73
Chapter 2 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 2.1.1 ACTIVATE BLUETOOTH® HID & SELECT KEYBOARD TYPE When Bluetooth® HID interface is activated, you will have to select a keyboard type to complete this setting. By default, Bluetooth® HID is activated on the scanner, and the keyboard type is set to PCAT (US). Activate Bluetooth® HID & Select Keyboard Type… 1) Read the barcode above to activate Bluetooth® HID and select a keyboard type. 2) Read the “Decimal Value” barcode on page 錯誤! 尚未定義書籤。.
PAGE 74
1663 A Barcode Scanner User Guide 2.1.2 RESET CONNECTION For Bluetooth® HID, you can only have the scanner connected to one computer at a time. If you want to connect the scanner to another host, you must read the “Reset Connection” barcode so that the current connection record will be cleared. Then, the scanner will restart itself automatically. Go through the process in 1.17 Hardware Reset and 3.2.3 Connect to Dongle to establish a new connection.
PAGE 75
Chapter 2 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 2.1.3 KEYBOARD SETTINGS       Alphabet Layout Numeric Layout Capital Lock Type Capital Lock Setting Alphabet Transmission Numeric Transmission Note: Bluetooth® HID does not support these functions on PDAs – (1) Capital Lock Setting: Auto Detection (2) Numeric Transmission: Numeric Keys Alphabet Layout By default, the alphabet layout is set to normal mode, also known as the standard English layout.
PAGE 76
1663 A Barcode Scanner User Guide US Keyboard Style – Normal QWERTY layout, which is normally used in western countries.  Select “Lower Row” for the “Numeric Layout” setting for the upper row is for special characters. French Keyboard Style – AZERTY French layout; see below for French Keyboard Style.  Select “Upper Row” for the “Numeric Layout” setting for the lower row is for special characters. German Keyboard Layout – QWERTZ German layout; see below for German Keyboard Style.
PAGE 77
Chapter 2 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 Numeric Layout Select a proper layout that matches the alphabet layout. The scanner will make adjustments according to this setting.
PAGE 78
1663 A Barcode Scanner User Guide Capital Lock Capital Lock State Description Capital Lock OFF Assuming that the status of Caps Lock on the keyboard is OFF, transmitted characters are exactly the same as in the barcode (when "case-sensitive" is selected for Alphabet Transmission). Capital Lock ON Assuming that the status of Caps Lock on the keyboard is ON, transmitted characters are exactly the same as in the barcode (when "case-sensitive" is selected for Alphabet Transmission).
PAGE 79
Chapter 2 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 Alphabet Transmission By default, the alphabet transmission is case-sensitive, meaning that the alphabet will be transmitted according to the original case, the status of Caps Lock on the keyboard, as well as the Capital Lock setting. Select [Ignore Case] to have alphabet transmitted according to the status of Caps Lock on the keyboard only. Ignore Case *Case-sensitive Refer to 5.1 Letter Case.
PAGE 80
1663 A Barcode Scanner User Guide Numeric Transmission By default, the alphanumeric keypad is used for transmitting digits. Select “Numeric Keypad” if you wish to use the keys on the numeric keypad. Numeric Key *Alphanumeric Key Note: If you select “Numeric Keypad”, the Num Lock status of the physical keyboard should be “ON”. This setting is not supported on PDAs. 2.1.4 INTER-CHARACTER DELAY By default, the inter-character delay is set to zero.
PAGE 81
Chapter 2 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 2.1.5 INTER-FUNCTION DELAY By default, the inter-function delay is set to zero. Specify a value, ranging from 0 to 254 in units of milliseconds, to match the computer response time of the keyboard interface. Such delay time is inserted between every function code (0x01 ~ 0x1F) being transmitted. The longer the delay time is, the slower the transmission speed will be.
PAGE 82
1663 A Barcode Scanner User Guide 2.1.7 SPECIAL KEYBOARD FEATURE By default, the special keyboard feature is based on the factory definition. You can decide whether to apply the special keyboard feature. Refer to 錯誤! 找不到參照來源。. *Apply Bypass 2.1.8 KEYPAD SUPPORT FOR IPHONE/IPAD When the scanner has been successfully connected to iPhone or iPad for data collection, the onscreen keypad of iPhone or iPad will disappear. Read the “Use POWER Key to Show or Hide Keypad” barcode in advance.
PAGE 83
Chapter 2 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 2.1.9 TRANSMIT SPEED By default, the BT HID transmit speed is set to normal. Users can have the scanner work in quicker transmit speed by reading the Fast barcode. *Fast Normal Note: Data loss may occur while transmitting data continuously with Fast mode enabled in the Android platform. Therefore, it’s recommended to employ the Normal mode for Android-based devices.
PAGE 84
1663 A Barcode Scanner User Guide 2.1.10 BT HID SLAVE/MASTER SWITCHING By default, the BT HID role is set to slave. Users can have the scanner switch between slave and master by reading the barcodes below. *Slave Master 2.1.11 BT HID AUTO-RECONNECTION Users can decide whether to have the scanner automatically reconnect to a paired device after disconnection, and the occasion for reconnecting. *Auto reconnect immediately Auto reconnect on data scanned Auto reconnect off 2.1.
PAGE 85
Chapter 2 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 2.2 BLUETOOTH® SPP SLAVE For Bluetooth® SPP Slave, refer to Chapter 3 – Setting up a WPAN Connection for related connection settings. 2.2.1 ACTIVATE BLUETOOTH® SPP SLAVE MODE This is SPP Slave Mode. Activate Bluetooth® SPP, Slave Mode 2.2.2 INTER-FUNCTION DELAY By default, the inter-function delay is set to zero. Specify a value, ranging from 0 to 254 in units of milliseconds, to match the computer response time of the keyboard interface.
PAGE 86
1663 A Barcode Scanner User Guide 2.2.3 ACK/NAK TIMEOUT By default, the scanner sends data to the host without waiting for an ACK/NAK response before sending more data. Specify a value, ranging from 1 to 99 in units of 0.1 second. If no response within the specified period of time, the scanner will attempt to send the same data two more times. If all attempts fail without any notification, data loss will occur.
PAGE 87
Chapter 2 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 2.2.4 BT SPP SLAVE HARDWARE FLOW CONTROL By default, the data sending via Bluetooth SPP doesn’t employ hardware flow control. In some cases users may want to enable hardware flow control to prevent data loss during transmission. Please scan the barcode below to enable/disable it.
PAGE 88
1663 A Barcode Scanner User Guide 2.3 BLUETOOTH® SPP MASTER As a SPP master device, the scanner will be able to resume connection with the host upon powering on again, as long as the host application is running. If the scanner fails to resume connection, it will try every 5 seconds to re-connect to the host unless you read the “Reset Connection” or “Restore System Defaults” barcode. For Bluetooth® SPP Master, refer 3.2.2 Configure Related Settings for related connection settings.
PAGE 89
Chapter 2 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 Note: Read the “Set Connection” barcode first, and then the “MAC ID” barcode within 10 seconds. Instead of producing the “MAC ID” barcode, you may read the setup barcodes for entering the MAC address.  Read the “Abort” barcode to cancel the operation at any time while reading setup barcodes for the MAC address. If the MAC address has not been completed yet, reading the “Validate” barcode can cancel the operation as well.
PAGE 90
1663 A Barcode Scanner User Guide Inter-Function Delay… (*0~254) 1) Read the barcode above to specify the inter-function delay. 2) Read the “Decimal Value” barcode on page 錯誤 ! 尚未定義書籤。 for the desired inter-function delay (in milliseconds). 3) Read the “Validate” barcode on the same page to complete this setting. 2.3.3 ACK/NAK TIMEOUT By default, the scanner sends data to the host without waiting for an ACK/NAK response before sending more data. Specify a value, ranging from 1 to 99 in units of 0.
PAGE 91
Chapter 2 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 2.3.4 SWITCH BETWEEN MASTER/SLAVE MODE After the scanner has established a connection as a SPP slave device, you may read the “Activate Bluetooth® SPP, Master Mode” setup barcode to switch to SPP Master Mode. This will result in easy and reliable re-connection, just like connecting with 3610. 2.3.5 BT SPP MASTER HARDWARE FLOW CONTROL By default, the data sending via Bluetooth SPP doesn’t employ hardware flow control.
PAGE 92
1663 A Barcode Scanner User Guide 2.4 USB HID VIA 3610 For USB HID, connect 3610 to the USB port of PC, and then connect the scanner to 3610. The scanned data will be transmitted to the computer. To capture the data run any text editor on your computer.
PAGE 93
Chapter 2 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 2.4.1 ACTIVATE USB HID & SELECT KEYBOARD TYPE When USB HID interface is activated, you will have to select a keyboard type to complete this setting. Activate 3610 USB HID & Select Keyboard Type… 1) Read the barcode above to activate USB HID and select a keyboard type. 2) Read the “Decimal Value” barcode on page 錯誤! 尚未定義書籤。. Refer to the table below for the number of desired keyboard type.
PAGE 94
1663 A Barcode Scanner User Guide 2.4.2 KEYBOARD SETTINGS       Alphabet Layout Numeric Layout Capital Lock Type Capital Lock Setting Alphabet Transmission Numeric Transmission Alphabet Layout By default, the alphabet layout is set to normal mode, also known as the standard English layout. Select French or German keyboard layout if necessary. The scanner will make adjustments when sending the "A", "Q", "W", "Z", "Y", and "M" characters according to this setting.
PAGE 95
Chapter 2 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 US Keyboard Style – Normal QWERTY layout, which is normally used in western countries.  Select “Lower Row” for the “Numeric Layout” setting for the upper row is for special characters. French Keyboard Style – AZERTY French layout; see below for French Keyboard Style.  Select “Upper Row” for the “Numeric Layout” setting for the lower row is for special characters. German Keyboard Layout – QWERTZ German layout; see below for German Keyboard Style.
PAGE 96
1663 A Barcode Scanner User Guide Numeric Layout Select a proper layout that matches the alphabet layout. The scanner will make adjustments according to this setting. Options Description Normal Depends on the [Shift] key or [Shift Lock] setting Lower Row For QWERTY or QWERTZ keyboard Upper Row For AZERTY keyboard *Normal Upper Row Lower Row Note: This setting is to be used with the Character Substitution setting when support for certain keyboard types (languages) is unavailable but required.
PAGE 97
Chapter 2 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 Capital Lock Type & Setting In order to send the alphabet with correct case, the scanner needs to know the status of Caps Lock on the keyboard. Incorrect settings may result in reversed case of the alphabet being transmitted. Cap Lock Type Description Normal Normal type Capital Lock When enabled, the keys of alphabetic characters will be interpreted as capital letters. However, this does not affect the number or punctuation keys.
PAGE 98
1663 A Barcode Scanner User Guide *Capital Lock OFF Alphabet Transmission By default, the alphabet transmission is case-sensitive, meaning that the alphabet will be transmitted according to the original case, the status of Caps Lock on the keyboard, as well as the Capital Lock setting. Select [Ignore Case] to have alphabet transmitted according to the status of Caps Lock on the keyboard only. Ignore Case *Case-sensitive Refer to 5.1 Letter Case.
PAGE 99
Chapter 2 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 Numeric Transmission By default, the alphanumeric keypad is used for transmitting digits. Select “Numeric Keypad” if you wish to use the keys on the numeric keypad. Numeric Key *Alphanumeric Key Note: If you select “Numeric Keypad”, the Num Lock status of the physical keyboard should be "ON". 2.4.3 INTER-CHARACTER DELAY By default, the inter-character delay is set to zero.
PAGE 100
1663 A Barcode Scanner User Guide 2.4.4 INTER-FUNCTION DELAY By default, the inter-function delay is set to zero. Specify a value, ranging from 0 to 254 in units of milliseconds, to match the computer response time of the keyboard interface. Such delay time is inserted between every function code (0x01 ~ 0x1F) being transmitted. The longer the delay time is, the slower the transmission speed will be. Inter-Function Delay… (*0~254) 1) Read the barcode above to specify the inter-function delay.
PAGE 101
Chapter 2 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 Bypass 2.4.7 USB HID VIA 3610 AUTO-RECONNECTION Users can decide whether to have the scanner automatically reconnect to a paired device after disconnection, and the occasion for reconnecting. *Auto reconnect immediately Auto reconnect on data scanned Auto reconnect off 2.4.8 USB POLLING INTERVAL Scan the barcodes below to specify the USB polling interval ranging from 1 to 15ms. It’s set to 10ms by default.
PAGE 102
1663 A Barcode Scanner User Guide *Disable 2.5 USB VIRTUAL COM VIA 3610 Connect 3610 to the USB port of PC, and then connect the scanner to 3610. You may run HyperTerminal.exe on the computer to view and capture the data transmission from the scanner. 2.5.1 ACTIVATE USB VIRTUAL COM Activate 3610 USB Virtual COM Note: If you are using USB Virtual COM for the first time, you must install its driver beforehand. Driver version 5.4 or later is required.
PAGE 103
Chapter 2 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 3) Read the “Validate” barcode on the same page to complete this setting. 2.5.4 ACK/NAK TIMEOUT By default, the scanner sends data to the host without waiting for an ACK/NAK response before sending more data. Specify a value, ranging from 1 to 99 in units of 0.1 second. If no response within the specified period of time, the scanner will attempt to send the same data two more times. If all attempts fail without any notification, data loss will occur.
PAGE 104
1663 A Barcode Scanner User Guide 2.5.5 USB VIRTUAL COM/COM_CDC VIA 3610 AUTO-RECONNECTION Users can decide whether to have the scanner automatically reconnect to a paired device after disconnection, and the occasion for reconnecting.
PAGE 105
Chapter 2 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 2.6 DIRECT USB HID 1663 A supports “Direct” USB HID interface for memory mode. Use the provided USB cable to connect 1663 A to the USB port of PC. Run any text editor on a computer to view and capture the scanned data being transmitted to the computer. Refer to 1.2.2 Memory Mode.
PAGE 106
1663 A Barcode Scanner User Guide 2.6.1 ACTIVATE USB HID & SELECT KEYBOARD TYPE When USB HID interface is activated, please select a keyboard type to complete this setting. Activate Direct USB HID & Select Keyboard Type… 1) Read the barcode above to activate USB HID and select a keyboard type. 2) Read the “Decimal Value” barcode page 錯誤! 尚未定義書籤。 . Refer to the table below for the number of desired keyboard type. 3) Read the “Validate” barcode on the same page to complete this setting.
PAGE 107
Chapter 2 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 2.6.2 KEYBOARD SETTINGS       Alphabet Layout Numeric Layout Capital Lock Type Capital Lock Setting Alphabet Transmission Numeric Transmission Alphabet Layout By default, the alphabet layout is set to normal mode, also known as the standard English layout. Select French or German keyboard layout if necessary. The scanner will make adjustments when sending the "A", "Q", "W", "Z", "Y", and "M" characters according to this setting.
PAGE 108
1663 A Barcode Scanner User Guide US Keyboard Style – Normal QWERTY layout, which is normally used in western countries.  Select “Lower Row” for the “Numeric Layout” setting for the upper row is for special characters. French Keyboard Style – AZERTY French layout; see below for French Keyboard Style.  Select “Upper Row” for the “Numeric Layout” setting for the lower row is for special characters. German Keyboard Layout – QWERTZ German layout; see below for German Keyboard Style.
PAGE 109
Chapter 2 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 Numeric Layout Select a proper layout that matches the alphabet layout. The scanner will make adjustments according to this setting.
PAGE 110
1663 A Barcode Scanner User Guide Capital Lock Type & Setting In order to send the alphabet with correct case, the scanner needs to know the status of Caps Lock on the keyboard. Incorrect settings may result in reversed case of the alphabet being transmitted. Cap Lock Type Description Normal Normal type Capital Lock When enabled, the keys of alphabetic characters will be interpreted as capital letters. However, this does not affect the number or punctuation keys.
PAGE 111
Chapter 2 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 *Capital Lock OFF Alphabet Transmission By default, the alphabet transmission is case-sensitive, meaning that the alphabet will be transmitted according to the original case, the status of Caps Lock on the keyboard, as well as the Capital Lock setting. Select [Ignore Case] to have alphabet transmitted according to the status of Caps Lock on the keyboard only. Ignore Case *Case-sensitive Refer to 5.1 Letter Case.
PAGE 112
1663 A Barcode Scanner User Guide Numeric Transmission By default, the alphanumeric keypad is used for transmitting numerics. Select “Numeric Keypad” if want to use the keys on the numeric keypad. Numeric Key *Alphanumeric Key Note: If selecting “Numeric Keypad”, the Num Lock status of the physical keyboard should be "ON". 2.6.3 INTER-CHARACTER DELAY By default, the inter-character delay is set to zero.
PAGE 113
Chapter 2 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 2.6.4 INTER-FUNCTION DELAY By default, the inter-function delay is set to zero. Specify a value, ranging from 0 to 254 in units of milliseconds, to match the computer response time of the keyboard interface. Such delay time is inserted between every function code (0x01 ~ 0x1F) being transmitted. The longer the delay time is, the slower the transmission speed will be.
PAGE 114
1663 A Barcode Scanner User Guide 2.6.6 SPECIAL KEYBOARD FEATURE By default, the special keyboard feature is based on the factory definition. You can decide whether to apply the special keyboard feature. Refer to 錯誤! 找不到參照來源。. *Apply Bypass 2.6.7 USB POLLING INTERVAL Scan the barcodes below to specify the USB polling interval ranging from 1 to 15ms. It’s set to 10ms by default. Set USB polling interval 1~15 ms (*10) 1) Read the barcode above to specify the USB polling interval.
PAGE 115
Chapter 2 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 2.6.8 CONTROL CHARACTER OUTPUT (WINDOWS ONLY) Enable this function to output control characters ranging from 0x01 to 0x1F in text form. For instance, [BS] (the backspace) is output rather than 0x08 when this function is enabled.
PAGE 116
1663 A Barcode Scanner User Guide 2.7 DIRECT USB VIRTUAL COM 1663 A supports “Direct” USB Virtual COM interface for memory mode. Use the provided USB cable to connect 1663 A to the USB port of PC. You may run HyperTerminal.exe on a computer to view and capture the scanned data being transmitted to the computer. Refer to 1.2.2 Memory Mode. 2.7.1 ACTIVATE USB VIRTUAL COM *Activate Direct USB Virtual COM Note: If using USB Virtual COM for the first time, install its driver beforehand. Driver version 5.
PAGE 117
Chapter 2 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 2.7.3 ACK/NAK TIMEOUT By default, the scanner sends data to the host without waiting for an ACK/NAK response before sending more data. Specify a value, ranging from 1 to 99 in units of 0.1 second. If no response within the specified period of time, the scanner will attempt to send the same data two more times. If all attempts fail without any notification, data loss will occur.
PAGE 118
Chapter 3 SET UP A WPAN CONNECTION The scanner can be configured to send data to a host computer wirelessly via the 3610 dongle, or to a notebook computer or PDA with Bluetooth® wireless technology. Upon powering up, the scanner will be ready to establish a WPAN connection. To establish a connection via 3610 after reading “Set Connection” and “Serial No.” barcodes … Interface Option Reference USB HID 2.4 USB HID via 3610 USB Virtual COM 2.
PAGE 119
Chapter 3 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 3.1 CONNECTING VIA 3610 By default, the interface of 3610 is set to “USB HID”. You can have up to seven scanners connected to one computer at the same time. Note: If using USB Virtual COM for the first time, you must install its driver beforehand. Driver version 5.4 or later is required. Please remove older versions! 3.1.1 CONNECT TO 3610 The scanner can connect to 3610 by scanning either two setting barcodes or a single 1D setting barcode.
PAGE 120
1663 A Barcode Scanner User Guide 3.1.2 CHANGE INTERFACE If you want to change the communication interface of 3610, use one of the connected scanners to configure the interface-related settings and the scanner will pass the new settings to 3610, which will then initialize and pass the settings to other connected scanners. 1) Read the “Set Connection” and “Serial Number” barcodes at the back of 3610. 2) Within two minutes, connect 3610 to the USB port of PC.
PAGE 121
Chapter 3 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 3.2 CONNECTING VIA BLUETOOTH® DONGLE 3.2.1 CHANGE INTERFACE Below is the procedure to configure the scanner before establishing a WPAN connection via Bluetooth® dongle. 1) Read the “Enter Setup” barcode to enter the configuration mode.
PAGE 122
1663 A Barcode Scanner User Guide 3.2.2 CONFIGURE RELATED SETTINGS Sniff Mode (Power-saving) By default, this feature is enabled, meaning the scanner will listen to the wireless network at a reduced rate. *Enable Disable Note: When connecting more than two scanners to a notebook computer or PDA with Bluetooth® wireless technology, we suggest that you disable the power-saving setting for a more reliable connection.
PAGE 123
Chapter 3 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 1) Read the barcode above to configure the device name. 2) Read the “Hexadecimal Value” barcode on page 錯誤! 尚未定義書籤。 for the desired character string. 3) Read the “Validate” barcode to complete this setting.
PAGE 124
1663 A Barcode Scanner User Guide Authentication When any changes are made to authentication and PIN code on the scanner side, you will have to remove the scanner from the paired device list (called unpairing) and go through the whole process to re-establish the connection. The scanner allows up to 16 characters for a PIN code and provides two options for authentication: Enable Authentication with Preset PIN Read the “Use preset PIN” barcode, and change the preset PIN if necessary.
PAGE 125
Chapter 3 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 Use random PIN No PIN required Note: When using Bluetooth® HID, some device driver may not support pre-defined PIN code for authentication. In this case, make sure you have the scanner set to “No PIN or use random PIN” before pairing. While pairing, the host PIN code will be displayed on the computer screen. Have the scanner read the setup barcode “Enter PIN Code in Decimal” or “Enter PIN Code in Hexadecimal” to input the matching PIN code.
PAGE 126
1663 A Barcode Scanner User Guide 3.2.3 CONNECT TO DONGLE The procedure goes through associating devices for establishing a WPAN connection, which is pretty much the same except for the software you are using. If your computer is running Microsoft® Windows® XP (SP1 to SP3), Windows Vista® Service Pack 1 (SP1) and Windows 7, you can use the software support that Windows® includes, or you can use the driver that the device manufacturer provides.
PAGE 127
Chapter 3 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 4) Turn on the scanner with correct WPAN settings, such as select Bluetooth® SPP or Bluetooth® HID, broadcasting enabled, authentication enabled, and PIN code specified, etc. Select the check box of [My device is set up and ready to be found] on your computer. 5) Click [Next]. 6) Wait for a few seconds for the Wizard to search available devices nearby. The scanner will appear with its “serial number” as the device name.
PAGE 128
1663 A Barcode Scanner User Guide 7) Click [Next]. 8) Enter the passkey for authentication, which must be exactly the same as configured for the scanner.
PAGE 129
Chapter 3 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 9) Click [Next]. Wait for a few seconds for Windows to exchange passkeys.
PAGE 130
1663 A Barcode Scanner User Guide Note: When Bluetooth security is enabled without providing a pre-set PIN code, dynamic input of PIN code is supported. 10) Click [Finish].
PAGE 131
Chapter 3 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 11) Now the target scanner will be listed as below. You can have up to seven scanners connected to one computer at the same time. Click to remove the selected item Note: When any changes are made to authentication and PIN code on the scanner side, or you want to change to use Bluetooth® HID, it is suggested that you remove the scanner from the paired device list (called unpairing) and go through the whole process to re-establish the connection.
PAGE 132
1663 A Barcode Scanner User Guide Bluetooth® SPP Connected Bluetooth® SPP Disconnected 116 Enter Setup
PAGE 133
Chapter 3 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 3.2.4 SECURE SIMPLE PAIRING (SSP) Secure Simple Pairing (SSP), introduced in Bluetooth® Core Specification 2.1 + EDR, is a new feature designed to ease the pairing process while keeping up the communication security level. This function is disabled by default. When connecting to a Bluetooth® host that supports Bluetooth® HID or Bluetooth® SPP profile, you can implement the secure simple pairing process.
PAGE 134
PAGE 135
Chapter 4 CHANGE SYMBOLOGY SETTINGS In this chapter, a brief on the symbology settings is provided for your reference. Users can simply scan the setting barcodes below to disable/enable all symbologies. Enable Disable Settings for each particular symbology will be depicted as follows. IN THIS CHAPTER 4.1 Codabar ................................................................... 4.2 Code 25 – Industrial 25 ............................................. 4.3 Code 25 – Interleaved 25.........................
PAGE 136
1663 A Barcode Scanner User Guide 4.1 CODABAR *Enable Disable 4.1.1 CODABAR SECURITY LEVEL Security Level renders more decoding accuracy giving consideration to barcodes’ print quality. Decide the security level for reading CodaBar barcodes. * High Normal 4.1.
PAGE 137
Chapter 4 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 4.1.3 START/STOP TRANSMISSION Decide whether to include the start/stop characters in the data being transmitted. Transmit Start/Stop Characters *Do Not Transmit 4.1.4 CLSI CONVERSION When enabled, the CLSI editing strips the start/stop characters and inserts a space after the first, fifth, and tenth characters of a 14-character Codabar barcode.
PAGE 138
1663 A Barcode Scanner User Guide 4.2 CODE 25 – INDUSTRIAL 25 *Enable Disable 4.2.1 START/STOP PATTERN SELECTION This decides the readability of all 2 of 5 symbology variants. For example, flight tickets actually use an Industrial 2 of 5 barcode but with Interleaved 2 of 5 start/stop pattern. In order to read this barcode, the start/stop pattern selection parameter of Industrial 2 of 5 should set to "Interleaved 25".
PAGE 139
Chapter 4 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 4.2.2 VERIFY CHECK DIGIT Decide whether to verify the check digit. If incorrect, the barcode will not be accepted. Verify Industrial 25 Check Digit *Do Not Verify 4.2.3 TRANSMIT CHECK DIGIT Decide whether to include the check digit in the data being transmitted.
PAGE 140
1663 A Barcode Scanner User Guide 4.2.4 CODE LENGTH QUALIFICATION To prevent the "short scan" error, define the "Length Qualification" settings to ensure that the correct barcode is read by qualifying the allowable code length.  If "Max/Min Length" is selected, the maximum length and the minimum length must be specified. It only accepts those barcodes with lengths that fall between max/min lengths specified.  If “Fixed Length” is selected, up to 2 fixed lengths can be specified.
PAGE 141
Chapter 4 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 4.2.5 SECURITY LEVEL Security Level renders more decoding accuracy giving consideration to barcodes’ print quality. Decide the security level for reading Code 25 barcodes. Normal *High 4.3 CODE 25 – INTERLEAVED 25 *Enable Disable 4.3.1 START/STOP PATTERN SELECTION This decides the readability of all 2 of 5 symbology variants. For example, flight tickets actually use an Industrial 2 of 5 barcode but with Interleaved 2 of 5 start/stop pattern.
PAGE 142
1663 A Barcode Scanner User Guide 4.3.2 VERIFY CHECK DIGIT Decide whether to verify the check digit. If incorrect, the barcode will not be accepted. Verify Interleaved 25 Check Digit *Do Not Verify 4.3.3 TRANSMIT CHECK DIGIT Decide whether to include the check digit in the data being transmitted.
PAGE 143
Chapter 4 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 4.3.4 CODE LENGTH QUALIFICATION To prevent the "short scan" error, define the "Length Qualification" settings to ensure that the correct barcode is read by qualifying the allowable code length.  If "Max/Min Length" is selected, the maximum length and the minimum length must be specified. It only accepts those barcodes with lengths that fall between max/min lengths specified.  If “Fixed Length” is selected, up to 2 fixed lengths can be specified.
PAGE 144
1663 A Barcode Scanner User Guide 4.4 CODE 25 – MATRIX 25 Enable *Disable 4.4.1 START/STOP PATTERN SELECTION This decides the readability of all 2 of 5 symbology variants. For example, flight tickets actually use an Industrial 2 of 5 barcode but with Interleaved 2 of 5 start/stop pattern. In order to read this barcode, the start/stop pattern selection parameter of Industrial 2 of 5 should set to "Interleaved 25".
PAGE 145
Chapter 4 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 4.4.2 VERIFY CHECK DIGIT Decide whether to verify the check digit. If incorrect, the barcode will not be accepted. Verify Matrix 25 Check Digit *Do Not Verify 4.4.3 TRANSMIT CHECK DIGIT Decide whether to include the check digit in the data being transmitted.
PAGE 146
1663 A Barcode Scanner User Guide 4.4.4 CODE LENGTH QUALIFICATION To prevent the "short scan" error, define the "Length Qualification" settings to ensure that the correct barcode is read by qualifying the allowable code length.  If "Max/Min Length" is selected, the maximum length and the minimum length must be specified. It only accepts those barcodes with lengths that fall between max/min lengths specified.  If “Fixed Length” is selected, up to 2 fixed lengths can be specified.
PAGE 147
Chapter 4 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 4.5 CODE 39 *Enable Disable 4.5.1 START/STOP TRANSMISSION Decide whether to include the start/stop characters in the data being transmitted. Transmit Code 39 Start/Stop Characters *Do Not Transmit 4.5.2 VERIFY CHECK DIGIT Decide whether to verify check digit. If incorrect, the barcode will not be accepted. Verify Code 39 Check Digit *Do Not Verify 4.5.3 TRANSMIT CHECK DIGIT Decide whether to include the check digit in the data being transmitted.
PAGE 148
1663 A Barcode Scanner User Guide Do Not Transmit 4.5.4 STANDARD/FULL ASCII CODE 39 Decide whether to support Code 39 Full ASCII that includes all the alphanumeric and special characters. Code 39 Full ASCII *Standard Code 39 4.5.5 CODE 39 SECURITY LEVEL Security Level renders more decoding accuracy giving consideration to barcodes’ print quality. Decide the security level for reading Code 39 barcodes. *Normal High 4.5.
PAGE 149
Chapter 4 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 4.6 TRIOPTIC CODE 39 Enable *Disable 4.7 CODE 93 *Enable Disable 4.8 CODE 128 *Enable Disable 4.8.1 CODE 128 SECURITY LEVEL Security Level renders more decoding accuracy giving consideration to barcodes’ print quality. Decide the security level for reading Code 128 barcodes.
PAGE 150
1663 A Barcode Scanner User Guide 4.
PAGE 151
Chapter 4 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 4.9.1 CONVERT TO EAN-13 Decide whether to expand the read EAN-8 barcode, as well as its addons, into EAN-13.  After conversion, the data follows EAN-13 format and is affected by EAN-13 programming selections (e.g. Check Digit). Convert EAN-8 to EAN-13 *Do Not Convert 4.9.2 TRANSMIT CHECK DIGIT Decide whether to include the check digit in the data being transmitted. *Transmit EAN-8 Check Digit Do Not Transmit 4.9.
PAGE 152
1663 A Barcode Scanner User Guide 4.
PAGE 153
Chapter 4 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 4.10.1 ISBN CONVERSION Decide whether to convert the EAN-13 barcode, starting with 978 and 979, to ISBN. Convert EAN-13 to ISBN *Do Not Convert 4.10.2 ISSN CONVERSION Decide whether to convert the EAN-13 barcode, starting with 977 to ISSN. Convert EAN-13 to ISSN *Do Not Convert 4.10.3 TRANSMIT CHECK DIGIT Decide whether to include the check digit in the data being transmitted.
PAGE 154
1663 A Barcode Scanner User Guide 4.10.4 EAN-13 SECURITY LEVEL Security Level renders more decoding accuracy giving consideration to barcodes’ print quality. Decide the security level for reading EAN-13 barcodes.
PAGE 155
Chapter 4 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 4.11 GS1-128 (EAN-128) *Enable Disable Note: GS1-128 barcodes can be decoded only when this setting is enabled. However, for 1660 with firmware version no later than 1.30, GS1-128 barcodes are taken as Code 128 when this setting is disabled. 4.11.1 CODE ID TRANSMISSION Decide whether to include the Code ID ("]C1") in the data being transmitted. Transmit Code ID *Do Not Transmit 4.11.
PAGE 156
1663 A Barcode Scanner User Guide Note: GS1-128 barcodes start with the FNC1 control character to distinguish themselves from other uses of Code 128. FNC1 is also used to separate data fields in the GS1-128 barcodes. 4.11.3 GS1 FORMATTING Decide whether to enable GS1 formatting for GS1-128. When enabled, code ID transmission will be disabled; however, the field separator and application ID mark characters will be automatically added to the output data.
PAGE 157
Chapter 4 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 4.12 ISBT 128 *Enable Disable Note: When enabled, it not only can decode single ISBT barcode, but also decode and concatenates pairs of ISBT barcodes. 4.12.1 ISBT CONCATENATION Decide whether to decode and concatenate pairs of ISBT barcodes.  Disable ISBT Concatenation It will not concatenate pairs of ISBT barcodes it encounters. Only one single ISBT 128 barcode outputs.
PAGE 158
1663 A Barcode Scanner User Guide 4.13 MSI Enable *Disable 4.13.1 VERIFY CHECK DIGIT Select one of the three calculations to verify check digit when decoding barcodes. If incorrect, the barcode will not be accepted. *Single Modulo 10 Double Modulo 10 Modulo 10 & 11 4.13.2 TRANSMIT CHECK DIGIT Decide whether to include the check digit in the data being transmitted.
PAGE 159
Chapter 4 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 4.13.3 CODE LENGTH QUALIFICATION To prevent the "short scan" error, define the "Length Qualification" settings to ensure that the correct barcode is read by qualifying the allowable code length.  If "Max/Min Length" is selected, the maximum length and the minimum length must be specified. It only accepts those barcodes with lengths that fall between max/min lengths specified.  If “Fixed Length” is selected, up to 2 fixed lengths can be specified.
PAGE 160
1663 A Barcode Scanner User Guide 4.14 FRENCH PHARMACODE Enable *Disable 4.14.1 TRANSMIT CHECK DIGIT Decide whether to include the check digit in the data being transmitted.
PAGE 161
Chapter 4 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 4.15 ITALIAN PHARMACODE Enable *Disable 4.15.1 TRANSMIT CHECK DIGIT Decide whether to include the check digit in the data being transmitted.
PAGE 162
1663 A Barcode Scanner User Guide 4.16 PLESSEY Enable *Disable 4.16.1 CONVERT TO UK PLESSEY Decide whether to change each occurrence of the character 'A' to character 'X' in the decoded data. Convert to UK Plessey *Do Not Convert 4.16.2 TRANSMIT CHECK DIGIT Decide whether to include the two check digits in the data being transmitted.
PAGE 163
Chapter 4 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 4.
PAGE 164
1663 A Barcode Scanner User Guide 4.17.2 GS1 DATABAR OMNIDIRECTIONAL (RSS-14) Enable RSS-14 & RSS Expanded (Groups I, II) *Disable When GS1 formatting for GS1 DataBar (RSS Family) is enabled, code ID transmitting will be disabled; however, the application ID and check digit transmitting will be enabled automatically.
PAGE 165
Chapter 4 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 Transmit Check Digit Decide whether to include the check digit in the data being transmitted. *Transmit RSS-14 Check Digit Do Not Transmit 4.17.3 GS1 DATABAR EXPANDED (RSS EXPANDED) Enable RSS-14 & RSS Expanded (Groups I, II) *Disable When GS1 formatting for GS1 DataBar (RSS Family) is enabled, code ID transmitting will be disabled automatically.
PAGE 166
3 A Barcode Scanner User Guide 4.17.4 GS1 DATABAR LIMITED (RSS LIMITED) Enable RSS Limited (Group III) *Disable When GS1 formatting for GS1 DataBar (RSS Family) is enabled, code ID transmitting will be disabled; however, the application ID and check digit transmitting will be enabled automatically. Transmit Code ID Decide whether to include the Code ID in the data being transmitted.
PAGE 167
Chapter 4 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 4.17.5 FIELD SEPARATOR (GS CHARACTER) Decide whether to apply a field separator (to convert the GS control character to human readable character). Specify Field Separator… 1) Read the barcode above to specify field separator. 2) Read the “Hexadecimal Value” barcode on page 錯誤! 尚未定義書籤。 for the desired character string. 3) Read the “Validate” barcode to complete this setting. 4.17.
PAGE 168
1663 A Barcode Scanner User Guide 4.17.7 GS1 DATABAR SECURITY LEVEL Security Level renders more decoding accuracy giving consideration to barcodes’ print quality. Decide the security level for reading GS1 DataBar barcodes.
PAGE 169
Chapter 4 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 4.18 TELEPEN Enable Telepen *Disable 4.18.1 TELEPEN OUTPUT – FULL ASCII/NUMERIC Decide whether to support Telepen in full ASCII code. By default, it supports ASCII mode.  AIM Telepen (Full ASCII) includes all the alphanumeric and special characters.
PAGE 170
1663 A Barcode Scanner User Guide 4.
PAGE 171
Chapter 4 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 4.19.1 CONVERT TO EAN-13 Decide whether to expand the read UPC-A barcode, as well as its addons, into EAN-13.  After conversion, the data follows EAN-13 format and is affected by EAN-13 programming selections (e.g. Check Digit). Convert UPC-A to EAN-13 *Do Not Convert 4.19.2 SYSTEM NUMBER TRANSMISSION Decide whether to include the system number in the data being transmitted. *Transmit UPC-A System Number Do Not Transmit 4.19.
PAGE 172
1663 A Barcode Scanner User Guide 4.
PAGE 173
Chapter 4 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 4.20.1 SYSTEM NUMBER SELECTION Decide whether to decode the ordinary UPC-E barcodes only or both UPC-E0 and UPC-E1 barcodes.  System number 0 enabled for decoding UPC-E0 barcodes.  System number 1 enabled for decoding UPC-E1 barcodes.
PAGE 174
1663 A Barcode Scanner User Guide 4.20.3 SYSTEM NUMBER TRANSMISSION Decide whether to include the system number in the data being transmitted. Transmit UPC-E System Number *Do Not Transmit 4.20.4 TRANSMIT CHECK DIGIT Decide whether to include the check digit in the data being transmitted.
PAGE 175
Chapter 4 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 4.21 CODE 11 Enable *Disable 4.21.1 VERIFICATION CHECK DIGIT Select one of the verification when decoding barcodes. If incorrect, the barcode will not be accepted.
PAGE 176
1663 A Barcode Scanner User Guide 4.21.2 TRANSMIT CHECK DIGIT Decide whether to include the check digit in the data being transmitted. *Transmit Check Digit Do Not Transmit 4.21.2 SECURITY LEVEL Security Level renders more decoding accuracy giving consideration to barcodes’ print quality. Decide the security level for reading Code 11 barcodes.
PAGE 177
Chapter 5 DEFINING OUTPUT FORMAT You may configure the format of the collected data output to the host computer. Barcodes read by the scanner will be processed in the following sequence – 1) Perform character substitution on the data scanned. 2) Add Code ID and Length Code to the front of the data:[Code ID][Length Code][Data] 3) Process the whole data in step 2 with user formats. Data is now divided into fields by user specified rules. Refer to Chapter 6 Applying Formats for Data Editing.
PAGE 178
1663 A Barcode Scanner User Guide 5.2 CHARACTER SUBSTITUTION Character substitution is performed on every occurrence of the first character specified. If only one character is specified, every occurrence of that character in the barcode will be taken away.  The first character will be replaced by the second character(s).  Up to three sets of character substitution can be configured.  If “Bluetooth® HID” or “USB HID” is configured for interface, Key Type and Key Status will then become applicable.
PAGE 179
Chapter 5 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 5.2.1 SELECT A SET FOR CHARACTER SUBSTITUION Configure Set 1 Configure Set 2 Configure Set 3 1) Read the barcode above to enable character substitution by set. For example, read the “Set 1” barcode to configure the first set of character substitution. The scanner will respond with one short beep, high tone, to indicate more setup barcodes are required. 2) Read the “Hexadecimal Value” barcode on page 錯誤! 尚未定義書籤。 for the desired character substitution.
PAGE 180
1663 A Barcode Scanner User Guide 5.2.2 SYMBOLOGIES FOR CHARACTER SUBSTITUTION (ALL 3 SETS) By default character substitution will be performed on all symbologies. If the character substitution is not desired with one or more symbologies, read the “Do Not Apply” barcode for each undesired symbologies and all the three sets will be ignored for them.
PAGE 181
Chapter 5 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 *Apply Do Not Apply Character Substitution for GS1-128 *Apply Do Not Apply Character Substitution for ISBT 128 *Apply Do Not Apply Character Substitution for EAN-8 (No Addon) *Apply Do Not Apply Character Substitution for EAN-8 Addon 2 *Apply Do Not Apply 165 Update
PAGE 182
1663 A Barcode Scanner User Guide Character Substitution for EAN-8 Addon 5 *Apply Do Not Apply Character Substitution for EAN-13 (No Addon) *Apply Do Not Apply Character Substitution for EAN-13 Addon 2 *Apply Do Not Apply Character Substitution for EAN-13 Addon 5 *Apply Do Not Apply Character Substitution for French Pharmacode *Apply Do Not Apply 166 Enter Setup
PAGE 183
Chapter 5 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 Character Substitution for Italian Pharmacode *Apply Do Not Apply Character Substitution for Industrial 25 *Apply Do Not Apply Character Substitution for Interleaved 25 *Apply Do Not Apply Character Substitution for Matrix 25 *Apply Do Not Apply Character Substitution for MSI *Apply Do Not Apply 167 Update
PAGE 184
1663 A Barcode Scanner User Guide Character Substitution for Plessey *Apply Do Not Apply Character Substitution for GS1 DataBar *Apply Do Not Apply Character Substitution for Telepen *Apply Do Not Apply Character Substitution for UPC-A (No Addon) *Apply Do Not Apply Character Substitution for UPC-A Addon 2 *Apply Do Not Apply 168 Enter Setup
PAGE 185
Chapter 5 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 Character Substitution for UPC-A Addon 5 *Apply Do Not Apply Character Substitution for UPC-E (No Addon) *Apply Do Not Apply Character Substitution for UPC-E Addon 2 *Apply Do Not Apply Character Substitution for UPC-E Addon 5 *Apply Do Not Apply Character Substitution for Code 11 *Apply Do Not Apply 169 Update
PAGE 186
1663 A Barcode Scanner User Guide 5.3 PREFIX/SUFFIX CODE By default, there is no prefix code, and [ENTER] or [CR] (Carriage Return) is configured to be suffix code. Up to 8 characters can be configured, for example, “Barcode_”, and you will have the string appear in front of the barcode read, like this – “Barcode_1234567890”.  If “Bluetooth® HID” or “USB HID” is configured for interface, Key Type and Key Status will then become applicable.
PAGE 187
Chapter 5 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 5.4 CODE ID Up to two characters for Code ID can be configured for each symbology. To make the Code ID configuration easier, the scanner provides five pre-defined Code ID sets that you can select one and make necessary changes on it.  If “Bluetooth® HID” or “USB HID” is configured for interface, Key Type and Key Status will then become applicable. You may decide whether or not to apply Key Status when “Normal Key” is selected for Key Type.
PAGE 188
1663 A Barcode Scanner User Guide Code ID options Set 1 Set 2 Set 3 Set 4 Set 5 Code 39 A C Y M A Trioptic Code 39 A C Y M X Italian Pharmacode A C Y M A French Pharmacode A C Y M A Industrial 25 C H H H S Interleaved 25 D I Z I S Matrix 25 E G G G S Codabar F N X N F Code 93 I L L L G Code 128 H K K K C ISBT 128 H K K K C UPC-E S E C E E EAN-8 P B B FF E EAN-13 M A A F E UPC-A J A A A E MSI V V D P M Ples
PAGE 189
Chapter 5 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 Code 39 A 0: No check character validation nor full ASCII processing. All data transmitted as decoded. 1: Modulo 43 check character validated and transmitted 3: Modulo 43 check character validated but not transmitted 4: Full ASCII character conversion performed. No check character validation. 5: Full ASCII character conversion performed. Modulo 43 check character validated and transmitted. 7: Full ASCII character conversion performed.
PAGE 190
1663 A Barcode Scanner User Guide 5.4.2 CHANGE CODE ID 1) Read the barcode below to change code ID of a specific symbology. 2) Read the “Hexadecimal Value” barcode on page 錯誤! 尚未定義書籤。 for the desired character string. For example, read “4” and “4” for applying the character [D] for Code ID. 3) Read the “Validate” barcode to complete this setting.
PAGE 191
Chapter 5 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 Configure Code ID for Codabar Configure Code ID for Code 39 Configure Code ID for Trioptic Code 39 Configure Code ID for Code 93 Configure Code ID for Code 128 Configure Code ID for ISBT 128 Configure Code ID for EAN-8 Configure Code ID for EAN-13 Configure Code ID for French Pharmacode Configure Code ID for Italian Pharmacode 175 Update
PAGE 192
1663 A Barcode Scanner User Guide Configure Code ID for Industrial 25 Configure Code ID for Interleaved 25 Configure Code ID for Matrix 25 Configure Code ID for MSI Configure Code ID for Plessey Configure Code ID for Telepen Configure Code ID for UPC-A Configure Code ID for UPC-E Configure Code ID for Code 11 5.4.
PAGE 193
Chapter 5 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 5.5 LENGTH CODE A 4-digit code representing the length of barcode data (character count) can be inserted in front of data being transmitted. Such "Length" code can be individually enabled or disabled for each symbology.
PAGE 194
1663 A Barcode Scanner User Guide Length Code for Code 128 Apply *Do Not Apply Length Code for GS1-128 & GS1 DataBar Apply *Do Not Apply Length Code for ISBT 128 Apply *Do Not Apply Length Code for EAN-8 Apply *Do Not Apply Length Code for EAN-13 Apply *Do Not Apply 178 Enter Setup
PAGE 195
Chapter 5 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 Length Code for French Pharmacode Apply *Do Not Apply Length Code for Italian Pharmacode Apply *Do Not Apply Length Code for Industrial 25 Apply *Do Not Apply Length Code for Interleaved 25 Apply *Do Not Apply Length Code for Matrix 25 Apply *Do Not Apply 179 Update
PAGE 196
1663 A Barcode Scanner User Guide Length Code for MSI Apply *Do Not Apply Length Code for Plessey Apply *Do Not Apply Length Code for Telepen Apply *Do Not Apply Length Code for UPC-A Apply *Do Not Apply Length Code for UPC-E Apply *Do Not Apply 180 Enter Setup
PAGE 197
Chapter 5 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 Length Code for Code 11 Apply *Do Not Apply 5.6 MULTI-BARCODE EDITOR The Multi-Barcode Editor allows deciding the output sequence of a concatenation of barcodes. Up to five barcodes can be specified. Enabling this function will force the scanner to apply Laser mode as the scan mode. Note: The Multi-Barcode Editor has nothing to do with Multi-Barcode Mode.
PAGE 198
1663 A Barcode Scanner User Guide 5.6.1 EDIT A CONCATENATION OF BARCODES Edit Output Sequence 1) Read the barcode above to start editing a concatenation of barcodes. 2) Code Type setting – read the “Hexadecimal Value” barcode on page 錯誤! 尚未定義書籤。 for Code Type of the (first) barcode. For example, read “4” and “1” for Code 39.
PAGE 199
Chapter 5 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 Code Type Symbology Code Type Symbology 40 (@) ISBT 128 4F (O) EAN-8 with Addon 5 41 (A) Code 39 50 (P) EAN-13 42 (B) Italian Pharmacode 51 (Q) EAN-13 with Addon 2 43 (C) French Pharmacode 52 (R) EAN-13 with Addon 5 44 (D) Industrial 25 53 (S) MSI 45 (E) Interleaved 25 54 (T) Plessey 46 (F) Matrix 25 55 (U) GS1-128 (EAN-128) 47 (G) Codabar (NW7) 56 (V) UPC-A 48 (H) Code 93 57 (W) UPC-A with Addon 2 49 (I) Code 12
PAGE 200
1663 A Barcode Scanner User Guide 5.6.2 ACTIVATE THE CONCATENATION OF BARCODES By default, the output sequence editing of the concatenation of barcodes is not applied. When “Enforce Output Sequence” is enabled, all barcodes read by the scanner must meet with the criteria for the concatenation. If data is found excluded from all output sequence sets (= not meeting with the criteria), the scanner will not accept the reading, and therefore, data will not be transmitted.
PAGE 201
Chapter 5 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 5.7 REMOVAL OF SPECIAL CHARACTER You can only specify 1 character, but it will remove every matching character encountered from the starting position of barcode data until a different character is met. For example, if it is configured to remove the character “0” (hex value is “30”), one or more zeros will be stripped off the barcode data “012345” and “00012345”. However, for barcode data “010333”, only the first zero will be stripped off.
PAGE 202
PAGE 203
Chapter 6 APPLYING FORMATS FOR DATA EDITING The scanner allows advanced data editing by applying user-configured editing formats. The whole processed data can be divided into fields by user-specified rules. The data actually sent to the host computer comprises those fields together with the user-configurable additional fields.
PAGE 204
1663 A Barcode Scanner User Guide 6.1 ACTIVATING EDITING FORMATS 6.1.1 ACTIVATE EDITING FORMATS If you have already configured any editing format before, you may directly apply the editing format. If not, you must start with configuring an editing format first, and then, activate the editing format when it is desired in use.
PAGE 205
Chapter 6 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 Editing Format 5 Enable *Disable 6.1.2 EXCLUSIVE DATA EDITING By default, only barcodes found meeting with the criteria are processed by the editing formats. Those found not meeting with the criteria are processed normally. When “Exclusive Data Editing” is enabled, all barcodes read by the scanner must be processed by the editing formats.
PAGE 206
1663 A Barcode Scanner User Guide 6.
PAGE 207
Chapter 6 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 6.2.1 SELECT FORMAT TO CONFIGURE Start Programming Format Select one editing format (Format 1~5) and the parameters pertaining to the editing format can then be configured – applicable code type, data length, matching string & location, start position, field adjustment, total number of fields, field settings (field-dividing rule), additional fields, and field transmission sequence.  Up to five different formats can be specified.
PAGE 208
1663 A Barcode Scanner User Guide 6.2.2 RESTORE DEFAULT FORMAT You may select an existing editing format and have the defaults restored. The default settings of an editing format are listed below.
PAGE 209
Chapter 6 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 6.3 CONFIGURE FORMAT — DEFINE DATA CRITERIA Three applicable conditions can be configured to check whether the data read by the scanner can be processed by the particular editing format. Note: Data editing cannot be performed unless the three conditions are all met. 6.3.1 APPLICABLE CODE TYPE By default, barcodes of all the supported symbologies will be processed by any editing format, if having been configured and enabled.
PAGE 210
1663 A Barcode Scanner User Guide Editing Format for Codabar *Apply Do Not Apply Editing Format for Code 39 *Apply Do Not Apply Editing Format for Trioptic Code 39 *Apply Do Not Apply Editing Format for Code 93 *Apply Do Not Apply Editing Format for Code 128 *Apply Do Not Apply 194 End Programming Format
PAGE 211
Chapter 6 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 Editing Format for GS1-128 & GS1 DataBar *Apply Do Not Apply Editing Format for ISBT 128 *Apply Do Not Apply Editing Format for EAN-8 *Apply Do Not Apply Editing Format for EAN-8 Addon 2 *Apply Do Not Apply Editing Format for EAN-8 Addon 5 *Apply Do Not Apply 195 Update
PAGE 212
1663 A Barcode Scanner User Guide Editing Format for EAN-13 *Apply Do Not Apply Editing Format for EAN-13 Addon 2 *Apply Do Not Apply Editing Format for EAN-13 Addon 5 *Apply Do Not Apply Editing Format for French Pharmacode *Apply Do Not Apply Editing Format for Italian Pharmacode *Apply Do Not Apply 196 End Programming Format
PAGE 213
Chapter 6 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 Editing Format for Industrial 25 *Apply Do Not Apply Editing Format for Interleaved 25 *Apply Do Not Apply Editing Format for Matrix 25 *Apply Do Not Apply Editing Format for MSI *Apply Do Not Apply Editing Format for Plessey *Apply Do Not Apply 197 Update
PAGE 214
1663 A Barcode Scanner User Guide Editing Format for Telepen *Apply Do Not Apply Editing Format for UPC-A *Apply Do Not Apply Editing Format for UPC-A Addon 2 *Apply Do Not Apply Editing Format for UPC-A Addon 5 *Apply Do Not Apply Editing Format for UPC-E *Apply Do Not Apply 198 End Programming Format
PAGE 215
Chapter 6 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 Editing Format for UPC-E Addon 2 *Apply Do Not Apply Editing Format for UPC-E Addon 5 *Apply Do Not Apply Editing Format for Code 11 *Apply Do Not Apply 199 Update
PAGE 216
1663 A Barcode Scanner User Guide 6.3.2 DATA LENGTH The length must include prefix, suffix (0x0d by default), length code, etc. By default, barcodes of any length (character count) are eligible for data editing.  A value ranging from 0 to 254 can be specified.  When zero is given to Max. & Min. Length, the scanner will not perform the length qualification. 1) Read the barcode below to specify Max. Length or Min. Length separately, and follow steps 2~3. Max. Length Min.
PAGE 217
Chapter 6 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 6.3.3 MATCHING STRING & LOCATION By default, no matching string is specified, and therefore, it is disabled. You may enable this feature by specifying a matching string up to four characters.  When the Matching String Location is zero, the scanner will only check for the existence of the matching string in the barcode data.  Specify a value from 1 to 254 to indicate where the matching string starts in the barcode data.
PAGE 218
1663 A Barcode Scanner User Guide 6.4 CONFIGURE FORMAT — DEFINE DATA FIELD 6.4.1 START POSITION Data can be divided into fields in one of the following direction –  from head (F1) to tail (F5)  from tail (F1) to head (F5) *From Head From Tail 6.4.2 FIELD ADJUSTMENT You may apply equal length to all fields, if necessary. If data is found longer than specified, it will be truncated automatically. When data is found shorter, it will add “Space” (0x20) to field.
PAGE 219
Chapter 6 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 6.4.3 TOTAL NUMBER OF FIELDS Data can be divided into at most 6 fields; each of them is numbered from F1 to F6 accordingly. However, only F1~F5 can be configured.  The total number of fields must be specified correctly. If three fields are configured for the editing format, the data characters after F3 will be assigned to F4 automatically. This feature is quite useful especially when data of variable lengths is processed by editing formats.
PAGE 220
1663 A Barcode Scanner User Guide 6.4.4 FIELD SETTINGS Data eligible for editing formats is divided into fields by user-specified rules – either using the field terminating string or specified field length. By Terminating String Specify the field terminating string. Up to two characters are allowed. The scanner will search for the occurrence of this particular string in the data.  By default, this string will be included in the field. You may discard it.
PAGE 221
Chapter 6 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 Field 2 Setting 1) Read the barcode below to divide field 2 by a specified terminating string. Select Field Separator to Divide Field 2… 2) Read the “Hexadecimal Value” barcode on page 錯誤! 尚未定義書籤。 for the desired character string. 3) Read the “Validate” barcode to complete this setting. 4) Read the “Discard Separator” barcode if the field separator is not desired in the field.
PAGE 222
1663 A Barcode Scanner User Guide Field 3 Setting 1) Read the barcode below to divide field 3 by a specified terminating string. Select Field Separator to Divide Field 3… 2) Read the “Hexadecimal Value” barcode on page 錯誤! 尚未定義書籤。 for the desired character string. 3) Read the “Validate” barcode to complete this setting. 4) Read the “Discard Separator” barcode if the field separator is not desired in the field.
PAGE 223
Chapter 6 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 Field 4 Setting 1) Read the barcode below to divide field 4 by a specified terminating string. Select Field Separator to Divide Field 4… 2) Read the “Hexadecimal Value” barcode on page 錯誤! 尚未定義書籤。 for the desired character string. 3) Read the “Validate” barcode to complete this setting. 4) Read the “Discard Separator” barcode if the field separator is not desired in the field.
PAGE 224
1663 A Barcode Scanner User Guide Field 5 Setting 1) Read the barcode below to divide field 5 by a specified terminating string. Select Field Separator to Divide Field 5… 2) Read the “Hexadecimal Value” barcode on page 錯誤! 尚未定義書籤。 for the desired character string. 3) Read the “Validate” barcode to complete this setting. 4) Read the “Discard Separator” barcode if the field separator is not desired in the field.
PAGE 225
Chapter 6 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 Additional Fields Up to five additional fields can be created for each editing format; each of them is numbered from AF1 to AF5 accordingly.  If “Bluetooth® HID” or “USB HID” is configured for interface, Key Type and Key Status will then become applicable. You may decide whether or not to apply Key Status when “Normal Key” is selected for Key Type. Key Type Key Status Scan Code Up to 2 scan code values are allowed.
PAGE 226
1663 A Barcode Scanner User Guide 6.4.5 PAUSE FIELD SETTING Pause Field Time You can limit the pause time interval (1~16). By default, it is set to 1 second. Pause Field Time 1~16 sec. (*1) 1) Read the barcode above to specify the time interval for the Pause Field. (It is set to 1 by default.) 2) Read the “Decimal Value” barcode on page 錯誤! 尚未定義書籤。. For example, read “1” and “0” for setting the Pause Field Time to 10 seconds. 3) Read the “Validate” barcode on the same page to complete this setting.
PAGE 227
Chapter 6 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 6.5 CONFIGURE FORMAT — DEFINE TRANSMISSION SEQUENCE After configuring the data fields and additional fields, you must now program the transmission sequence of these fields that comprise the final data. This field transmission sequence can be assigned in any desired order and fields can be assigned multiple times as well. Note: Up to twelve fields can be assigned. 1) Read the “Start” barcode to begin with programming the field transmission sequence.
PAGE 228
1663 A Barcode Scanner User Guide Additional Field 2 Additional Field 3 Additional Field 4 Additional Field 5 Pause Field Null Character Field 3) Read the “End” barcode to complete this setting.
PAGE 229
Chapter 6 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 6.6 PROGRAMMING EXAMPLES 6.6.1 EXAMPLE I Extract data from the 10th character to the 19th character... The editing format should be configured as follows: 1) Read the “Enter Setup” barcode to enter the Configuration Mode. 2) Read the “Configure Format 1” barcode. 3) Read the “Clear All” and “Code 128” barcodes for applicable code type. 4) Read the “Three Fields” barcode. 5) Read the “Divide Field 1 by Length” barcode, and set length to 9.
PAGE 230
1663 A Barcode Scanner User Guide 6.6.2 EXAMPLE II Extract the date code, item number, and quantity information from barcodes. Data in a barcode is encoded like this:    From the 1st character to the 6th character is the date code. From the 7th character to the dash ‘-’ character is the item number. After the dash ‘-’ character is the quantity information.
PAGE 231
SPECIFICATIONS Optical Characteristics 1663 A Scan Engine Non-contact type Optical Sensor 2500 pixels CCD image sensor Light Source Visible Red LED Scan Rate 200 scans/second RF Characteristics WPAN Module Bluetooth® Class 2, Version 2.
PAGE 232
1663 A Barcode Scanner User Guide Electrical Characteristics Battery Rechargeable Li-ion battery — 3.
PAGE 233
217 Update