User guide

ManualsBrandsCipherLab ManualsBarcode Reader1504

1504 Barcode Scanne

Setup barcodes included.

Version 1.06

Summary of content (217 pages)

PAGE 1
504 Barcode Scanner Setup barcodes included. Version 1.
PAGE 2
Copyright © 2011~2012 CIPHERLAB CO., LTD. All rights reserved The software contains proprietary information of CIPHERLAB CO., LTD.; it is provided under a license agreement containing restrictions on use and disclosure and is also protected by copyright law. Reverse engineering of the software is prohibited. Due to continued product development this information may change without notice.
PAGE 3
IMPORTANT NOTICES FOR USA This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
PAGE 4
FOR PRODUCT WITH LASER CAUTION This laser component emits FDA / IEC Class 2 laser light at the exit port. Do not stare into beam. SAFETY PRECAUTIONS DO NOT expose the scanner to any flammable sources. Under no circumstances, internal components are self-serviceable. For AC power adaptor, a socket outlet shall be installed near the equipment and shall be easily accessible. Make sure there is stable power supply for the scanner or its peripherals to operate properly.
PAGE 5
RELEASE NOTES Version Date Notes 1.06 Apr. 12, 2012 New: Quick Start | Read a Setup Barcode | List Current Settings - “List Page 22” added to deliver settings of Driver Liscense parsing New: Appendix V: Reading Driver Licenses Dec. 22, 2011 Modified: Divide keyboard wedge table into apply and bypass partitions Modified: 3.11 GS1-128 — Change GS1-128 default value to Enable. New: 2.
PAGE 6
PAGE 7
CONTENTS IMPORTANT NOTICES ...................................................................................................................... - 3 For USA .......................................................................................................................................... - 3 For Canada .................................................................................................................................... - 3 For Product with Laser ........................................
PAGE 8
1504 Barcode Scanner User Guide 1.6.7 Presentation Mode...........................................................................................................24 1.7 Scanning Timeout.....................................................................................................................25 1.8 Delay between Re-read ............................................................................................................ 26 1.9 Read Redundancy (1D) ............................................
PAGE 9
1504 Barcode Scanner User Guide 3.2 Code 25 – Industrial 25 ........................................................................................................... 66 3.2.1 Code Length Qualification ...............................................................................................67 3.3 Code 25 – Interleaved 25........................................................................................................68 3.3.1 Verify Check Digit ...................................................
PAGE 10
1504 Barcode Scanner User Guide 3.19.2 Convert to UPC-A............................................................................................................99 3.19.3 Transmit System Number............................................................................................100 3.19.4 Transmit Check Digit ...................................................................................................100 3.20 Code 11 .............................................................................
PAGE 11
1504 Barcode Scanner User Guide 4.6 Multi-Barcode Editor...............................................................................................................144 4.6.1 Edit a Concatenation of Barcodes ................................................................................145 4.6.2 Activate the Concatenation of Barcodes ......................................................................147 4.7 Removal of Special Character ..................................................................
PAGE 12
1504 Barcode Scanner User Guide Data Sequence Setup ...................................................................................................................197 Separators and Fields...................................................................................................................203 Edit Separators.........................................................................................................................204 Edit Fields .................................................
PAGE 13
INTRODUCTION The small-form-factor 1500 Series Barcode Scanners are now capable of reading 2D barcodes. The tethered handheld scanners are designed to help accelerate productivity while lowering the total cost of ownership. Intensive data collection jobs are made easier with fast, accurate barcode scanning in various working environments, especially in small businesses. A new ordering option is provided for adapting a 2D scan engine to read both 1D and 2D barcodes.
PAGE 14
1504 Barcode Scanner User Guide INSIDE THE PACKAGE The items included in the package may be different, depending on order. Rich choices of output interfaces are available to enhance the total performance of the scanner. Refer to product specifications. Save the box and packaging material for future use in case it is need to store or ship the scanner.
PAGE 15
Introduction SYMBOLOGIES SUPPORTED Most of the popular barcode symbologies are supported, as listed below. Each can be individually enabled or disabled. The scanner will automatically discriminate and recognize all the symbologies that are enabled. Refer to Chapter 3 Changing Symbology Settings for details of each symbology.
PAGE 16
1504 Barcode Scanner User Guide GS1 DataBar Limited (RSS Limited) Disabled GS1 DataBar Expanded (RSS Expanded) Disabled GS1 DataBar Expanded Stacked Disabled Code 11 Composite Code Postal Code 2D Symbologies Disabled Composite CC-A/B Disabled Composite CC-C Disabled Composite TLC-39 Disabled US Postnet Enabled US Planet Enabled UK Postal Enabled Japan Postal Enabled Australian Postal Enabled Dutch Postal Enabled USPS 4CB/One Code/Intelligent Mail Disabled UPU FICS Postal Disab
PAGE 17
QUICK START The configuration of the scanner can be done by reading the setup barcodes contained in this manual or via the ScanMaster software. This section describes the procedure of configuring the scanner by reading the setup barcodes and provides some examples for demonstration. Note: If RS-232 or USB Virtual COM is selected for output interface, the host can directly send serial commands to configure the scanner. For example, run HyperTerminal.
PAGE 18
1504 Barcode Scanner User Guide ENTER CONFIGURATION MODE For the scanner to enter the configuration mode, having it read the "Enter Setup" barcode, which can be located at the bottom of almost every even page of this manual. The scanner will respond with six beeps and its LED indicator will become flashing red after reading the barcode. Enter Setup For configuring scanner parameters, see “Read a Setup Barcode” below.
PAGE 19
Quick Start DEFAULT SETTINGS SAVE USER SETTINGS AS DEFAULTS For the scanner to keep the customized settings as user defaults, having it read the “Save as User Defaults” barcode. This is a normal setup barcode, and the scanner will respond with two beeps (low-high tone). After reading the “Update” barcode, the current settings will be saved as user defaults.
PAGE 20
1504 Barcode Scanner User Guide READ A SETUP BARCODE CONFIGURE PARAMETERS For most of the scanner parameters, only one read is required to set them to new values. The scanner will respond with two beeps (low-high tone) when each parameter is set successfully. But for a number of special parameters, multiple reads are required to complete the setting. In this case, the scanner will respond with a short beep to indicate it needs to read more setup barcodes.
PAGE 21
Quick Start The example below shows how to save settings as “User Default” so that to restore user defaults later: Steps Action User Feedback if Successful 1 Power on the scanner… The scanner will respond with a long beep (high tone) and its LED indicator will become solid red and go off quickly. 2 Enter the Configuration Mode… The scanner will respond with six beeps (high-low tone repeats three times), and its LED indicator will be flashing red.
PAGE 22
1504 Barcode Scanner User Guide The example below shows how to set numeric parameters: Steps Action User Feedback if Successful 1 Power on the scanner... The scanner will respond with a long beep (high tone) and its LED indicator will become solid red and go off quickly. 2 Enter the Configuration Mode… The scanner will respond with six beeps (high-low tone repeats three times), and its LED indicator will become flashing red. 3 Read a Setup barcode...
PAGE 23
Quick Start The example below shows how to set string parameters: Steps Action User Feedback if Successful 1 Power on the scanner... The scanner will respond with a long beep (high tone) and its LED indicator will become solid red and go off quickly. 2 Enter the Configuration Mode… The scanner will respond with six beeps (high-low tone repeats three times), and its LED indicator will become flashing red. 3 Read a Setup barcode...
PAGE 24
1504 Barcode Scanner User Guide LIST THE CURRENT SETTINGS The current settings of all scanner parameters can be sent to the host computer for user inspection. The listing includes pages as shown below. Select the page of interest by having the scanner read the “List Page x” barcode. The scanner will respond with two beeps (low-high tone) and send the selected page to the host immediately.
PAGE 25
Quick Start Lists settings regarding Editing Format 1 (1/2) List Page 11 Lists settings regarding Editing Format 1 (2/2) List Page 12 Lists settings regarding Editing Format 2 (1/2) List Page 13 Lists settings regarding Editing Format 2 (2/2) List Page 14 Lists settings regarding Editing Format 3 (1/2) List Page 15 Lists settings regarding Editing Format 3 (2/2) List Page 16 Lists settings regarding Editing Format 4 (1/2) List Page 17 Lists settings regarding Editing Format 4 (2/2) List Page
PAGE 26
1504 Barcode Scanner User Guide CREATE ONE-SCAN SETUP BARCODES The fact is most of the scanner parameters require only one read for setting new values. To facilitate configuring the scanner, create One-Scan setup barcodes for use.
PAGE 27
Chapter 1 UNDERSTANDING THE BARCODE SCANNER This chapter explains the features and usage of the barcode scanner. IN THIS CHAPTER 1.1 Power ...................................................................... 1.2 Transmit Buffer ......................................................... 1.3 LED Indicator ............................................................ 1.4 Beeper ..................................................................... 1.5 Send “NR” to Host .........................................
PAGE 28
1504 Barcode Scanner User Guide 1.1 POWER Connect the interface cable between the scanner and computer. If using the RS-232 cable, it must join the power supply cord to power up the scanner. The scanner will respond with one long beep (high tone) and its LED indicator will become solid red and go off quickly. 1.2 TRANSMIT BUFFER The scanner is designed to send any collected data to a host computer one by one via the transmit buffer (SRAM).
PAGE 29
Chapter 1 Understanding the Barcode Scanner 1.3 LED INDICATOR The dual-color LED on top of the scanner is used to provide user feedback. For example, the LED becomes solid red and goes off quickly upon powering on or running out of transmit buffer. Tell the difference by the beeps – for example, it will hear a long beep of high tone when powering on the scanner, and a long beep of low tone when the transmit buffer becomes full.
PAGE 30
1504 Barcode Scanner User Guide 1.4 BEEPER The scanner has a buzzer to provide user feedback in various operating conditions.
PAGE 31
Chapter 1 Understanding the Barcode Scanner 1.4.
PAGE 32
1504 Barcode Scanner User Guide 1.5 SEND “NR” TO HOST This feature only works when Keyboard Wedge or RS-232 is selected for output interface. Have the scanner send the “NR” string to the host to notify the No Read event.
PAGE 33
Chapter 1 Understanding the Barcode Scanner 1.6 SCAN MODES Different scan modes are supported – select the scan mode that best suits the requirements of a specific application. Refer to the comparison table below. In any scan mode other than Multi-Barcode Mode, a barcode acceptable to 1504 can only contain data of 7 KB at most.
PAGE 34
1504 Barcode Scanner User Guide 1.6.2 LASER MODE The scanner will start scanning once the trigger is held down. The scanning won't stop until (1) a barcode is decoded, (2) the pre-set timeout expires, or (3) release the trigger. Note: Refer to “Scanning Timeout”. *Laser Mode 1.6.3 AUTO OFF MODE The scanner will start scanning once the trigger is pressed. The scanning won't stop until (1) a barcode is decoded, and (2) the pre-set timeout expires. Note: Refer to “Scanning Timeout”.
PAGE 35
Chapter 1 Understanding the Barcode Scanner 1.6.5 AIMING MODE The scanner will aim at a barcode once the trigger is pressed, and start scanning when the trigger is pressed again within one second. The scanning won't stop until (1) a barcode is decoded, and (2) the pre-set timeout expires. Aiming Mode Aiming Timeout Limit the aiming time interval (1~15). By default, the scanner time-out is set to 1 second. Aiming Time-out after 1~15 sec. (*1) 1.
PAGE 36
1504 Barcode Scanner User Guide 1.6.7 PRESENTATION MODE The scanner will be expecting barcodes. Whenever a barcode is brought within range, the scanner will be able to decode it. It is suggested to seat it in the Auto-Sense Stand for hands-free operation. Presentation Mode Low Light Enhancement Enable Low Light Enhancement will cause the illumination to remain on at a low power in low lighting conditions.
PAGE 37
Chapter 1 Understanding the Barcode Scanner 1.7 SCANNING TIMEOUT Specify the scanning time interval (1~254 sec.; 0= Disable) when the scan mode is set to any of the following – Laser mode Auto Off mode Auto Power Off mode Aiming mode Scanner Time-out after 0~254 sec. (*10) 1) Read the barcode above to specify the time interval before the scan engine times out. 2) Read the “Decimal Value” barcode on page 193.
PAGE 38
1504 Barcode Scanner User Guide 1.
PAGE 39
Chapter 1 Understanding the Barcode Scanner 1.9 READ REDUNDANCY (1D) Select the level of reading security. For example, If "No Redundancy" is selected, one successful decoding will make the reading valid and induce the "READER Event". If "Two Times" is selected, it will take a total of three consecutive successful decoding of the same barcode to make the reading valid. The higher the reading security is (that is, the more redundancy the user selects), the slower the reading speed gets.
PAGE 40
1504 Barcode Scanner User Guide 1.10 ADDON SECURITY FOR UPC/EAN BARCODES The scanner is capable of decoding a mix of UPC/EAN barcodes with and without addons. The read redundancy (2~30 times) allows changing the number of times to decode a UPC/EAN barcode before transmission. The more redundancy selected, the higher the reading security is, and thus, the slower the reading speed becomes. It will have to compromise between reading security and decoding speed.
PAGE 41
Chapter 1 Understanding the Barcode Scanner 1.11 AUTO-SENSE MODE This mode is only available when seat the scanner in the Auto-Sense Stand. Enable this mode, it will force the scanner to apply Laser mode as the scan mode. However, it works slightly different from the original Laser mode. Now the scanner will be expecting barcodes as long as it is seated in the Auto-Sense Stand, as shown below. Whenever a barcode is brought within range, the scanner will be able to decode it. Refer to 1.6.
PAGE 42
1504 Barcode Scanner User Guide Normally, barcodes are printed with the color of the bars darker than that of the spaces. But for negative barcodes, they are printed in the opposite sense just like negative films. The spaces of negative barcodes are printed with a color darker than that of the bars.
PAGE 43
Chapter 1 Understanding the Barcode Scanner 1.13 CABLE AUTO-DETECT Find the interface cable provided inside the package. Connect it to the scanner. The scanner will detect the interface automatically. Refer to Chapter 2 — Selecting Output Interface. Cable Auto-Detect Defaults Keyboard Wedge PCAT (US) for keyboard type RS-232 115200 bps, 8 bits, No parity, 1 stop bit USB USB HID and PCAT (US) for keyboard type Note: If “USB Virtual COM” is desired, have the scanner read the setup barcodes.
PAGE 44
1504 Barcode Scanner User Guide 1.14 PICKLIST MODE Picklist mode enables the decoder to decode only the barcodes aligned at the center under the laser aiming pattern.
PAGE 45
Chapter 2 SELECTING OUTPUT INTERFACE In order to establish a proper connection between computer and the scanner, it suggests following these instructions – 1) Connect the scanner and computer with the provided interface cable. The scanner is capable of detecting the interface. If using the RS-232 cable, join the power supply cord. If using the USB cable, it is set to USB HID by default. If “USB Virtual COM” is desired, have the scanner read the setup barcodes.
PAGE 46
1504 Barcode Scanner User Guide 2.1 KEYBOARD WEDGE The Y cable allows connecting the scanner to the keyboard input port of PC and joining the keyboard as well. The scanned data will be transmitted to the host keyboard port as if it is manually entered via the keyboard.
PAGE 47
Chapter 2 Selecting Output Interface 2.1.1 ACTIVATE KEYBOARD WEDGE & SELECT KEYBOARD TYPE When Keyboard Wedge interface is activated, it will have to select a keyboard type to complete this setting. Activate Keyboard Wedge & Select Keyboard Type… 1) Read this barcode above to activate Keyboard Wedge and select a keyboard type. 2) Read the “Decimal Value” barcode on page 193. Refer to the table below for the number of desired keyboard type.
PAGE 48
1504 Barcode Scanner User Guide 2.1.2 KEYBOARD SETTINGS Alphabets Layout Digits Layout Capital Lock Type Capital Lock Setting Alphabets Transmission Digits Transmission Kanji Transmission Alternate Composing Laptop Support Alphabets Layout By default, the alphabets layout is set to normal mode, also known as the standard English layout. Select French or German keyboard layout if necessary.
PAGE 49
Chapter 2 Selecting Output Interface US Keyboard Style – Normal QWERTY layout, which is normally used in western countries. Select “Lower Row” for the “Digits Layout” setting for the upper row is for special characters. French Keyboard Style – AZERTY French layout; see below for French Keyboard Style. Select “Upper Row” for the “Digits Layout” setting for the lower row is for special characters. German Keyboard Layout – QWERTZ German layout; see below for German Keyboard Style.
PAGE 50
1504 Barcode Scanner User Guide Digits Layout Select a proper layout that matches the alphabets layout. The scanner will make adjustments according to this setting.
PAGE 51
Chapter 2 Selecting Output Interface Capital Lock Type & Setting In order to send the alphabets with correct case, the scanner needs to know the status of Caps Lock on the keyboard. Incorrect settings may result in reversed case of the alphabets being transmitted. Cap Lock Type Description Normal Normal type Capital Lock When enabled, the keys of alphabetic characters will be interpreted as capital letters. However, this does not affect the number or punctuation keys.
PAGE 52
1504 Barcode Scanner User Guide *Capital Lock OFF Alphabets Transmission By default, the alphabets transmission is case-sensitive, meaning that the alphabets will be transmitted according to their original case, the status of Caps Lock on the keyboard, as well as the Capital Lock setting. Select [Ignore Case] to have alphabets transmitted according to the status of Caps Lock on the keyboard only. Ignore Case *Case-sensitive Refer to 4.1 Letter Case.
PAGE 53
Chapter 2 Selecting Output Interface Digits Transmission By default, the alphanumeric keypad is used for transmitting digits. Select “Numeric Keypad” if wishing to use the keys on the numeric keypad. Numeric Key *Alphanumeric Key Note: If selecting “Numeric Keypad”, the Num Lock status of the physical keyboard should be “ON”. Kanji Transmission Kanji Transmission is supported by the scanner when either Keyboard Wedge or Direct USB HID is selected for the output interface.
PAGE 54
1504 Barcode Scanner User Guide ALT Composing By default, Alternate key composing is disabled. Select [Yes] to allow emulating Alternate key code of a specific keyboard character. For example, [Alt] + [065] will be sent to host for the character “A” regardless the keyboard type using. Yes *No Laptop Support By default, laptop support value is disabled. It suggests enabling this feature if connecting the wedge cable to a laptop without an external keyboard being inter-connected. Enable *Disable 2.1.
PAGE 55
Chapter 2 Selecting Output Interface 2.1.4 INTER-FUNCTION DELAY By default, the inter-function delay is set to zero. Specify a value, ranging from 0 to 254 in units of millisecond, to match the computer response time of the keyboard interface. Such delay time is inserted between every function code (0x01 ~ 0x1F) being transmitted. The longer the delay time is, the slower the transmission speed will be. Inter-Function Delay… (*0~254) 1) Read the barcode above to specify the inter-function delay.
PAGE 56
1504 Barcode Scanner User Guide 2.2 RS-232 Use the RS-232 cable to connect the scanner to the serial port of PC and join the power adaptor to the RS-232 connector. The associated RS-232 parameters must match those configured on the computer. The scanned data will be transmitted to the serial port.
PAGE 57
Chapter 2 Selecting Output Interface 2400 bps 1200 bps 600 bps 2.2.3 DATA BITS *8 bits 7 bits 2.2.4 PARITY *No parity Even Odd 2.2.
PAGE 58
1504 Barcode Scanner User Guide 2.2.6 FLOW CONTROL By default, there is no flow control in use. Select the flow control (handshake) method. Options Description No No flow control Scanner Ready The scanner will activate the RTS signal upon powering on. After each good read, the scanner will then wait for the CTS signal to become active. Data will not be sent until the CTS signal becomes active. Data Ready The RTS signal will be activated after each good read.
PAGE 59
Chapter 2 Selecting Output Interface 2.2.7 INTER-CHARACTER DELAY By default, the inter-character delay is zero. Specify a value, ranging from 0 to 254 in units of millisecond, to match the computer response time. Such delay time is inserted between every character being transmitted. The longer the delay time is, the slower the transmission speed will be. Inter-Character Delay… (*0~254) 1) Read the barcode above to specify the inter-character delay.
PAGE 60
1504 Barcode Scanner User Guide 2.2.9 ACK/NAK TIMEOUT By default, the scanner sends data to the host without waiting for an ACK/NAK response before sending more data. Specify a value, ranging from 1 to 99 in units of 0.1 second. If no response within the specified period of time, the scanner will attempt to send the same data two more times. If all three attempts fail without any notification, data loss will occur.
PAGE 61
Chapter 2 Selecting Output Interface 2.3 DIRECT USB HID For USB HID, connect the scanner to the USB port of PC. Run any text editor on the computer, and the scanned data will be transmitted to the computer. HID Settings Defaults Keyboard Type PCAT (US) Digits Layout Normal Capital Lock Type Normal Capital Lock State Off Alphabets Transmission Case-sensitive Digits Transmission Alphanumeric keypad Kanji Transmission Disable Inter-Character Delay 0 (ms) Inter-Function Delay 0 (ms) 2.3.
PAGE 62
1504 Barcode Scanner User Guide 2.3.2 KEYBOARD SETTINGS Alphabets Layout Digits Layout Capital Lock Type Capital Lock Setting Alphabets Transmission Digits Transmission Kanji Transmission Alphabets Layout By default, the alphabets layout is set to normal mode, also known as the standard English layout. Select French or German keyboard layout if necessary. The scanner will make adjustments when sending the "A", "Q", "W", "Z", "Y", and "M" characters according to this setting.
PAGE 63
Chapter 2 Selecting Output Interface US Keyboard Style – Normal QWERTY layout, which is normally used in western countries. Select “Lower Row” for the “Digits Layout” setting for the upper row is for special characters. French Keyboard Style – AZERTY French layout; see below for French Keyboard Style. Select “Upper Row” for the “Digits Layout” setting for the lower row is for special characters. German Keyboard Layout – QWERTZ German layout; see below for German Keyboard Style.
PAGE 64
1504 Barcode Scanner User Guide Digits Layout Select a proper layout that matches the alphabets layout. The scanner will make adjustments according to this setting. Options Description Normal Depends on the [Shift] key or [Shift Lock] setting Lower Row For QWERTY or QWERTZ keyboard Upper Row For AZERTY keyboard *Normal Upper Row Lower Row Note: This setting is to be used with the Character Substitution setting when support to certain keyboard types (languages) is unavailable but required.
PAGE 65
Chapter 2 Selecting Output Interface Capital Lock Type & Setting In order to send the alphabets with correct case, the scanner needs to know the status of Caps Lock on the keyboard. Incorrect settings may result in reversed case of the alphabets being transmitted. Cap Lock Type Description Normal Normal type Capital Lock When enabled, the keys of alphabetic characters will be interpreted as capital letters. However, this does not affect the number or punctuation keys.
PAGE 66
1504 Barcode Scanner User Guide *Capital Lock OFF Alphabets Transmission By default, the alphabets transmission is case-sensitive, meaning that the alphabets will be transmitted according to their original case, the status of Caps Lock on the keyboard, as well as the Capital Lock setting. Select [Ignore Case] to have alphabets transmitted according to the status of Caps Lock on the keyboard only. Ignore Case *Case-sensitive Refer to 4.1 Letter Case.
PAGE 67
Chapter 2 Selecting Output Interface Digits Transmission By default, the alphanumeric keypad is used for transmitting digits. Select “Numeric Keypad” to use the keys on the numeric keypad. Numeric Key *Alphanumeric Key Note: If selecting “Numeric Keypad”, the Num Lock status of the physical keyboard should be "ON". Kanji Transmission Kanji Transmission is supported by the scanner when either Keyboard Wedge or Direct USB HID is selected for the output interface.
PAGE 68
1504 Barcode Scanner User Guide 2.3.3 INTER-CHARACTER DELAY By default, the inter-character delay is set to zero. Specify a value, ranging from 0 to 254 in units of millisecond, to match the computer response time of the keyboard interface. Such delay time is inserted between every character being transmitted. The longer the delay time is, the slower the transmission speed will be. Inter-Character Delay… (*0~254) 1) Read the barcode above to specify the inter-character delay.
PAGE 69
Chapter 2 Selecting Output Interface 2.3.5 HID CHARACTER TRANSMIT MODE By default, USB HID interface sends data to the host in batch. Have the scanner read the “By Character” barcode to process data one character at a time. *Batch Processing By Character 2.3.6 HID TRANSMIT SPEED In order to avoid missed characters during barcode output, you can slow-down the HID transmit speed. *Normal Faster Fastest 2.3.
PAGE 70
1504 Barcode Scanner User Guide 2.4 DIRECT USB VCOM For USB Virtual COM, connect the scanner to the USB port of PC. Run HyperTerminal.exe on the computer, and the scanned data will be transmitted to the computer. Note: If using USB Virtual COM for the first time, it must install its driver from the CD-ROM. Driver version 5.3 or later is required. Please remove older versions! For 1504 to connect to Windows PC, it must select Direct USB VCOM_CDC. Refer to 2.5 Direct USB VCOM_CDC. 2.4.
PAGE 71
Chapter 2 Selecting Output Interface 2.4.3 ACK/NAK TIMEOUT By default, the scanner sends data to the host without waiting for an ACK/NAK response before sending more data. Specify a value, ranging from 1 to 99 in units of 0.1 second. If no response within the specified period of time, the scanner will attempt to send the same data two more times. If all three attempts fail without any notification, data loss will occur.
PAGE 72
1504 Barcode Scanner User Guide 2.5 DIRECT USB VCOM_CDC For USB Virtual COM, connect the scanner to the USB port of PC. Run HyperTerminal.exe on the computer, and the scanned data will be transmitted to the computer. Note: If using USB Virtual COM for the first time, it must install its driver from the CD-ROM. USB CDC driver installer is available in the “Windows” folder for 1504, which will copy a vendor-supplied INF file to Windows. 2.5.1 ACTIVATE USB VCOM_CDC Activate Direct USB VCOM_CDC 2.5.
PAGE 73
Chapter 2 Selecting Output Interface 2.5.3 ACK/NAK TIMEOUT By default, the scanner sends data to the host without waiting for an ACK/NAK response before sending more data. Specify a value, ranging from 1 to 99 in units of 0.1 second. If no response within the specified period of time, the scanner will attempt to send the same data two more times. If all three attempts fail without any notification, data loss will occur.
PAGE 74
1504 Barcode Scanner User Guide 62 Enter Setup
PAGE 75
Chapter 3 CHANGING SYMBOLOGY SETTINGS In this chapter, a brief on the symbology settings is provided for reference. IN THIS CHAPTER 3.1 Codabar ................................................................... 64 3.2 Code 25 – Industrial 25 .............................................. 66 3.3 Code 25 – Interleaved 25............................................ 68 3.4 Code 25 – Matrix 25................................................... 71 3.5 Code 25 – Chinese 25 .......................................
PAGE 76
1504 Barcode Scanner User Guide 3.1 CODABAR *Enable Disable 3.1.1 START/STOP TRANSMISSION Decide whether to include the start/stop characters in the data being transmitted. Transmit Start/Stop Characters *Do Not Transmit 3.1.2 CLSI CONVERSION When enabled, the CLSI editing strips the start/stop characters and inserts a space after the first, fifth, and tenth characters of a 14-character Codabar barcode.
PAGE 77
Chapter 3 Changing Symbology Settings 3.1.3 CODE LENGTH QUALIFICATION To prevent the "short scan" error, define the "Length Qualification" settings to ensure that the correct barcode is read by qualifying the allowable code length. If "Max/Min Length" is selected, the maximum length and the minimum length must be specified. It only accepts those barcodes with lengths that fall between max/min lengths specified. If “Fixed Length” is selected, up to 2 fixed lengths can be specified.
PAGE 78
1504 Barcode Scanner User Guide 3.
PAGE 79
Chapter 3 Changing Symbology Settings 3.2.1 CODE LENGTH QUALIFICATION To prevent the "short scan" error, define the "Length Qualification" settings to ensure that the correct barcode is read by qualifying the allowable code length. If "Max/Min Length" is selected, the maximum length and the minimum length must be specified. It only accepts those barcodes with lengths that fall between max/min lengths specified. If “Fixed Length” is selected, up to 2 fixed lengths can be specified.
PAGE 80
1504 Barcode Scanner User Guide 3.3 CODE 25 – INTERLEAVED 25 *Enable Disable 3.3.1 VERIFY CHECK DIGIT Decide whether to verify the check digit. When desired, select one of the algorithms, USS or OPCC. If incorrect, the barcode will not be accepted. *Do Not Verify USS Check Digit OPCC Check Digit 3.3.2 TRANSMIT CHECK DIGIT Decide whether to include the check digit in the data being transmitted.
PAGE 81
Chapter 3 Changing Symbology Settings 3.3.3 CONVERT TO EAN-13 Decide whether to convert a 14-character barcode into EAN-13 if the following requirements are met: The barcode must have a leading 0 and a valid EAN-13 check digit. “Verify Check Digit” must be disabled.
PAGE 82
1504 Barcode Scanner User Guide 3.3.4 CODE LENGTH QUALIFICATION To prevent the "short scan" error, define the "Length Qualification" settings to ensure that the correct barcode is read by qualifying the allowable code length. If "Max/Min Length" is selected, the maximum length and the minimum length must be specified. It only accepts those barcodes with lengths that fall between max/min lengths specified. If “Fixed Length” is selected, up to 2 fixed lengths can be specified.
PAGE 83
Chapter 3 Changing Symbology Settings 3.4 CODE 25 – MATRIX 25 Enable *Disable 3.4.1 VERIFY CHECK DIGIT Decide whether to verify the check digit. If incorrect, the barcode will not be accepted. Verify Matrix 25 Check Digit *Do Not Verify 3.4.2 TRANSMIT CHECK DIGIT Decide whether to include the check digit in the data being transmitted.
PAGE 84
1504 Barcode Scanner User Guide 3.4.3 CODE LENGTH QUALIFICATION To prevent the "short scan" error, define the "Length Qualification" settings to ensure that the correct barcode is read by qualifying the allowable code length. If "Max/Min Length" is selected, the maximum length and the minimum length must be specified. It only accepts those barcodes with lengths that fall between max/min lengths specified. If “Fixed Length” is selected, up to 2 fixed lengths can be specified.
PAGE 85
Chapter 3 Changing Symbology Settings 3.
PAGE 86
1504 Barcode Scanner User Guide 3.6 ITALIAN PHARMACODE (CODE 32) Enable *Disable Note: Code 39 must be enabled first.
PAGE 87
Chapter 3 Changing Symbology Settings 3.7 CODE 39 *Enable Disable 3.7.1 VERIFY CHECK DIGIT Decide whether to verify the check digit. If incorrect, the barcode will not be accepted. Verify Code 39 Check Digit *Do Not Verify 3.7.2 TRANSMIT CHECK DIGIT Decide whether to include the check digit in the data being transmitted.
PAGE 88
1504 Barcode Scanner User Guide 3.7.3 STANDARD/FULL ASCII CODE 39 Decide whether to support Code 39 Full ASCII that includes all the alphanumeric and special characters. Code 39 Full ASCII *Standard Code 39 Note: Trioptic Code 39 and Code 39 Full ASCII cannot be enabled at the same time.
PAGE 89
Chapter 3 Changing Symbology Settings 3.7.4 CODE LENGTH QUALIFICATION To prevent the "short scan" error, define the "Length Qualification" settings to ensure that the correct barcode is read by qualifying the allowable code length. If "Max/Min Length" is selected, the maximum length and the minimum length must be specified. It only accepts those barcodes with lengths that fall between max/min lengths specified. If “Fixed Length” is selected, up to 2 fixed lengths can be specified.
PAGE 90
1504 Barcode Scanner User Guide 3.8 TRIOPTIC CODE 39 Decide whether to decode Trioptic Code 39. Trioptic Code 39 is a variant of Code 39 used in the marking of computer tap cartridges. It always contains six characters. Enable *Disable Note: Trioptic Code 39 and Code 39 Full ASCII cannot be enabled at the same time.
PAGE 91
Chapter 3 Changing Symbology Settings 3.
PAGE 92
1504 Barcode Scanner User Guide 3.9.1 CODE LENGTH QUALIFICATION To prevent the "short scan" error, define the "Length Qualification" settings to ensure that the correct barcode is read by qualifying the allowable code length. If "Max/Min Length" is selected, the maximum length and the minimum length must be specified. It only accepts those barcodes with lengths that fall between max/min lengths specified. If “Fixed Length” is selected, up to 2 fixed lengths can be specified.
PAGE 93
Chapter 3 Changing Symbology Settings 3.
PAGE 94
1504 Barcode Scanner User Guide 3.11 GS1-128 (EAN-128) *Enable Disable Note: GS1-128 barcodes can be decoded only when this setting is enabled. 3.11.1 TRANSMIT CODE ID Decide whether to include the Code ID (“]C1”) in the data being transmitted. Transmit GS1-128 Code ID *Do Not Transmit 3.11.2 FIELD SEPARATOR (GS CHARACTER) Decide whether to apply a field separator (to convert the FNC1 control character to human readable character).
PAGE 95
Chapter 3 Changing Symbology Settings 3.12 ISBT 128 *Enable Disable 3.12.1 ISBT CONCATENATION Decide whether to decode and concatenate pairs of ISBT barcodes. Disable ISBT Concatenation It will not concatenate pairs of ISBT barcodes it encounters. Enable ISBT Concatenation There must be two ISBT barcodes in order for the scanner to decode and perform concatenation. It does not decode single ISBT barcodes.
PAGE 96
1504 Barcode Scanner User Guide 3.12.2 ISBT CONCATENATION REDUNDANCY Specify the concatenation redundancy (2~20 times) when ISBT concatenation is enabled. ISBT Concatenation Redundancy 2~20 (*10) 1) Read the barcode above to specify the concatenation redundancy. 2) Read the “Decimal Value” barcode on page 193 for the desired redundancy. 3) Read the “Validate” barcode on the same page to complete this setting.
PAGE 97
Chapter 3 Changing Symbology Settings 3.
PAGE 98
1504 Barcode Scanner User Guide 3.13.2 GS1 DATABAR OMNIDIRECTIONAL (RSS-14) Enable RSS-14 & RSS Expanded (Groups I, II) *Disable The settings below apply to Group I symbologies only: GS1 DataBar Omnidirectional GS1 DataBar Truncated GS1 DataBar Stacked GS1 DataBar Stacked Omnidirectional Transmit Code ID Decide whether to include the Code ID in the data being transmitted.
PAGE 99
Chapter 3 Changing Symbology Settings 3.13.3 GS1 DATABAR EXPANDED (RSS EXPANDED) Enable RSS-14 & RSS Expanded (Groups I, II) *Disable The settings below apply to Group II symbologies only: GS1 DataBar Expanded GS1 DataBar Expanded Stacked Transmit Code ID Decide whether to include the Code ID in the data being transmitted.
PAGE 100
1504 Barcode Scanner User Guide 3.13.4 GS1 DATABAR LIMITED (RSS LIMITED) Enable RSS Limited (Group III) *Disable Transmit Code ID Decide whether to include the Code ID in the data being transmitted. *Transmit RSS Limited Code ID Do Not Transmit Transmit Application ID Decide whether to include the Application ID ("01") in the data being transmitted.
PAGE 101
Chapter 3 Changing Symbology Settings 3.13.5 CONVERT TO UPC/EAN This only applies to GS1 DataBar Omnidirectional and GS1 DataBar Limited barcodes not decoded as part of a Composite barcode. Convert to EAN-13: It will strip the leading “010” from barcodes. “01” is the Application ID and must be followed by a single zero (the first digit encoded). Convert to UPC-A: It will strip the leading “0100” from barcodes. “01” is the Application ID and must be followed by two or more zeros (but not six zeros).
PAGE 102
1504 Barcode Scanner User Guide 3.14 MSI Enable *Disable 3.14.1 VERIFY CHECK DIGIT Select one of the three calculations to verify check digit(s) when decoding barcodes. If incorrect, the barcode will not be accepted. *Single Modulo 10 Double Modulo 10 Modulo 10 & 11 3.14.2 TRANSMIT CHECK DIGIT Decide whether to include the check digit(s) in the data being transmitted.
PAGE 103
Chapter 3 Changing Symbology Settings 3.14.3 CODE LENGTH QUALIFICATION To prevent the "short scan" error, define the "Length Qualification" settings to ensure that the correct barcode is read by qualifying the allowable code length. If "Max/Min Length" is selected, the maximum length and the minimum length must be specified. It only accepts those barcodes with lengths that fall between max/min lengths specified. If “Fixed Length” is selected, up to 2 fixed lengths can be specified.
PAGE 104
1504 Barcode Scanner User Guide 3.
PAGE 105
Chapter 3 Changing Symbology Settings 3.
PAGE 106
1504 Barcode Scanner User Guide 3.16.1 CONVERT TO ISBN Decide whether to convert the EAN-13 barcode, starting with 978 and 979, to ISBN. Convert EAN-13 to ISBN *Do Not Convert 3.16.2 CONVERT TO ISSN Decide whether to convert the EAN-13 barcode, starting with 977 to ISSN.
PAGE 107
Chapter 3 Changing Symbology Settings 3.17 UCC COUPON EXTENDED CODE Decide whether to decode the following barcodes as Coupon Code.
PAGE 108
1504 Barcode Scanner User Guide 3.
PAGE 109
Chapter 3 Changing Symbology Settings 3.18.1 TRANSMIT SYSTEM NUMBER Decide whether to include the system number in the data being transmitted. *Transmit UPC-A System Number Do Not Transmit 3.18.2 TRANSMIT CHECK DIGIT Decide whether to include the check digit in the data being transmitted.
PAGE 110
1504 Barcode Scanner User Guide 3.
PAGE 111
Chapter 3 Changing Symbology Settings 3.19.1 SELECT SYSTEM NUMBER Decide whether to decode the ordinary UPC-E barcodes only or both UPC-E0 and UPC-E1 barcodes. System number 0 enabled for decoding UPC-E0 barcodes. System number 1 enabled for decoding UPC-E1 barcodes. System Number 0 & 1 *System Number 0 Only Warning: Because of the way system number 1 is encoded, if both system numbers are enabled, the user might suffer from short scanning UPC-A or EAN-13 barcodes into UPC-E1 barcodes. 3.19.
PAGE 112
1504 Barcode Scanner User Guide 3.19.3 TRANSMIT SYSTEM NUMBER Decide whether to include the system number in the data being transmitted. Transmit UPC-E System Number *Do Not Transmit 3.19.4 TRANSMIT CHECK DIGIT Decide whether to include the check digit in the data being transmitted.
PAGE 113
Chapter 3 Changing Symbology Settings 3.20 CODE 11 Enable *Disable 3.20.1 VERIFY CHECK DIGIT Decide whether to verify the check digit(s). If incorrect, the barcode will not be accepted. Verify One Check Digit Verify Two Check Digit *Do Not Verify 3.20.2 TRANSMIT CHECK DIGIT Decide whether to include the check digit(s) in the data being transmitted. Transmit Code 11 Check Digit *Do Not Transmit Note: "Verify Check Digit" must be enabled first.
PAGE 114
1504 Barcode Scanner User Guide 3.20.3 CODE LENGTH QUALIFICATION To prevent the "short scan" error, define the "Length Qualification" settings to ensure that the correct barcode is read by qualifying the allowable code length. If "Max/Min Length" is selected, the maximum length and the minimum length must be specified. It only accepts those barcodes with lengths that fall between max/min lengths specified. If “Fixed Length” is selected, up to 2 fixed lengths can be specified.
PAGE 115
Chapter 3 Changing Symbology Settings 3.21 COMPOSITE CODE 3.21.1 COMPOSITE CC-A/B Enable Composite CC-A/B *Disable 3.21.2 COMPOSITE CC-C Enable Composite CC-C *Disable 3.21.
PAGE 116
1504 Barcode Scanner User Guide 3.21.4 UPC COMPOSITE MODE UPC barcodes can be “linked” with a 2D barcode during transmission as if they were one barcode. UPC Never Linked Transmit UPC barcodes regardless of whether a 2D barcode is detected. UPC Always Linked Transmit UPC barcodes and the 2D portion. If the 2D portion is not detected, the UPC barcode will not be transmitted.
PAGE 117
Chapter 3 Changing Symbology Settings 3.22 US POSTAL CODE 3.22.1 US POSTNET *Enable US Postnet Disable 3.22.2 US PLANET *Enable US Planet Disable 3.22.3 TRANSMIT CHECK DIGIT Decide whether to include the check digit in the data being transmitted.
PAGE 118
1504 Barcode Scanner User Guide 3.23 UK POSTAL CODE 3.23.1 UK POSTAL *Enable UK Postal Disable 3.23.2 TRANSMIT CHECK DIGIT Decide whether to include the check digit in the data being transmitted.
PAGE 119
Chapter 3 Changing Symbology Settings 3.24 MORE POSTAL CODE 3.24.1 JAPAN POSTAL *Enable Japan Postal Disable 3.24.2 AUSTRALIAN POSTAL *Enable Australian Postal Disable 3.24.3 DUTCH POSTAL *Enable Dutch Postal Disable 3.24.
PAGE 120
1504 Barcode Scanner User Guide 3.24.
PAGE 121
Chapter 3 Changing Symbology Settings 3.25 2D SYMBOLOGIES 3.25.1 PDF417 *Enable PDF417 Disable 3.25.
PAGE 122
1504 Barcode Scanner User Guide 3.25.3 DATA MATRIX *Enable Data Matrix Disable Data Matrix Mirror Decide whether to decode mirror image Data Matrix barcodes. Never — do not decode Data Matrix barcodes that are mirror images. Always — decode only Data matrix barcodes that are mirror images. Auto — decode both mirrored and unmirrored Data Matrix barcoes.
PAGE 123
Chapter 3 Changing Symbology Settings 3.25.4 MAXICODE *Enable Maxicode Disable 3.25.5 QR CODE *Enable QR Code Disable 3.25.6 MicroQR *Enable MicroQR Disable 3.25.
PAGE 124
1504 Barcode Scanner User Guide 3.26 MACRO PDF Macro PDF is a special feature for concatenating multiple PDF barcodes into one file, known as Macro PDF417 or Macro MicroPDF417. Note: When printing barcodes, keep each Macro PDF sequence separate, as each has a unique identifier. Do not mix barcodes from several Macro PDF sequences, even if they encode the same data. When scan Macro PDF sequences, scan the entire Macro PDF sequence without interruption! 3.26.
PAGE 125
Chapter 3 Changing Symbology Settings 3.26.2 ESCAPE CHARACTERS When enabled, it uses process transmissions according to the Global of a Macro PDF symbol GLI formatting. the backslash "\" as an Escape character for systems that can containing special data sequences. It will format special data Label Identifier (GLI) protocol, which only affects the data portion transmission. The Control Header, if enabled, is always sent with GLI Protocol *None 3.26.
PAGE 126
1504 Barcode Scanner User Guide 114 Enter Setup
PAGE 127
Chapter 4 DEFINING OUTPUT FORMAT The scanner allows configuring in which format the collected data will be output to the host computer. Barcode read by the scanner will be processed in the following sequence – 1) Perform character substitution on the data scanned. 2) Add Code ID and Length Code to the front of the data:[Code ID][Length Code][Data] 3) Process the whole data in step 2 with user formats. Data is now divided into fields by user specified rules.
PAGE 128
1504 Barcode Scanner User Guide 4.2 CHARACTER SUBSTITUTION Character substitution is performed on every occurrence of the first character specified. If only one character is specified, every occurrence of that character in the barcode will be taken away. The first character will be replaced by the second character(s). Up to three sets of character substitution can be configured. If “Keyboard Wedge” or “USB HID” is configured for interface, Key Type and Key Status will then become applicable.
PAGE 129
Chapter 4 Defining Output Format 4.2.1 SELECT A SET FOR CHARACTER SUBSTITUION Configure Set 1 Configure Set 2 Configure Set 3 1) Read the barcode above to enable character substitution by set. For example, have the scanner read the “Set 1” barcode to configure the first set of character substitution. The scanner will respond with one short beep, high tone, to indicate more setup barcodes are required. 2) Read the “Hexadecimal Value” barcode on page 194 for the desired character substitution.
PAGE 130
1504 Barcode Scanner User Guide 4.2.2 SYMBOLOGIES FOR CHARACTER SUBSTITUTION (ALL 3 SETS) By default character substitution will be performed on all symbologies. If the character substitution is not desired with one or more symbologies, read the “Do Not Apply” barcode for each undesired symbologies and all the three sets will be ignored for them.
PAGE 131
Chapter 4 Defining Output Format Character Substitution for Code 128 *Apply Do Not Apply Character Substitution for GS1-128 *Apply Do Not Apply Character Substitution for ISBT 128 *Apply Do Not Apply Character Substitution for EAN-8 (No Addon) *Apply Do Not Apply Character Substitution for EAN-8 Addon 2 *Apply Do Not Apply 119 Update
PAGE 132
1504 Barcode Scanner User Guide Character Substitution for EAN-8 Addon 5 *Apply Do Not Apply Character Substitution for EAN-13 (No Addon) *Apply Do Not Apply Character Substitution for EAN-13 Addon 2 *Apply Do Not Apply Character Substitution for EAN-13 Addon 5 *Apply Do Not Apply Character Substitution for Italian Pharmacode *Apply Do Not Apply 120 Enter Setup
PAGE 133
Chapter 4 Defining Output Format Character Substitution for Industrial 25 *Apply Do Not Apply Character Substitution for Interleaved 25 *Apply Do Not Apply Character Substitution for Matrix 25 *Apply Do Not Apply Character Substitution for Chinese 25 *Apply Do Not Apply Character Substitution for MSI *Apply Do Not Apply 121 Update
PAGE 134
1504 Barcode Scanner User Guide Character Substitution for GS1 DataBar *Apply Do Not Apply Character Substitution for UPC-A (No Addon) *Apply Do Not Apply Character Substitution for UPC-A Addon 2 *Apply Do Not Apply Character Substitution for UPC-A Addon 5 *Apply Do Not Apply Character Substitution for UPC-E (No Addon) *Apply Do Not Apply 122 Enter Setup
PAGE 135
Chapter 4 Defining Output Format Character Substitution for UPC-E Addon 2 *Apply Do Not Apply Character Substitution for UPC-E Addon 5 *Apply Do Not Apply Character Substitution for UCC Coupon Extended Code *Apply Do Not Apply Character Substitution for Code 11 *Apply Do Not Apply Character Substitution for Composite CC-A/B *Apply Do Not Apply 123 Update
PAGE 136
1504 Barcode Scanner User Guide Character Substitution for Composite CC-C *Apply Do Not Apply Character Substitution for Composite TLC-39 *Apply Do Not Apply Character Substitution for US Postnet *Apply Do Not Apply Character Substitution for US Planet *Apply Do Not Apply Character Substitution for UK Postal *Apply Do Not Apply 124 Enter Setup
PAGE 137
Chapter 4 Defining Output Format Character Substitution for Japan Postal *Apply Do Not Apply Character Substitution for Australian Postal *Apply Do Not Apply Character Substitution for Dutch Postal *Apply Do Not Apply Character Substitution for USPS 4CB/One Code/Intelligent Mail *Apply Do Not Apply Character Substitution for UPU FICS Postal *Apply Do Not Apply 125 Update
PAGE 138
1504 Barcode Scanner User Guide Character Substitution for PDF417 *Apply Do Not Apply Character Substitution for MicroPDF417 *Apply Do Not Apply Character Substitution for Data Matrix *Apply Do Not Apply Character Substitution for Maxicode *Apply Do Not Apply Character Substitution for QR Code *Apply Do Not Apply 126 Enter Setup
PAGE 139
Chapter 4 Defining Output Format Character Substitution for MicroQR *Apply Do Not Apply Character Substitution for Aztec *Apply Do Not Apply 127 Update
PAGE 140
1504 Barcode Scanner User Guide 4.3 PREFIX/SUFFIX CODE By default, there is no prefix code, and [ENTER] or [CR] (Carriage Return) is configured to be suffix code. Up to 8 characters can be configured, for example, “Barcode_”, and have the string appear in front of the barcode read, like this – “Barcode_1234567890”. If “Keyboard Wedge” or “USB HID” is configured for interface, Key Type and Key Status will then become applicable. Decide whether to apply Key Status when select “Normal Key” for Key Type.
PAGE 141
Chapter 4 Defining Output Format 4.4 CODE ID Up to two characters for Code ID can be configured for each symbology. To make the Code ID configuration easier, the scanner provides five pre-defined Code ID sets that can select one and make necessary changes on it. If “Keyboard Wedge” or “USB HID” is configured for interface, Key Type and Key Status will then become applicable. Decide whether to apply Key Status when select “Normal Key” for Key Type.
PAGE 142
1504 Barcode Scanner User Guide Code ID options Set 1 Set 2 Set 3 Set 4 Set 5 Code 39 A C Y M A Trioptic Code 39 A C Y M X Italian Pharmacode A C Y M A Industrial 25 C H H H S Interleaved 25 D I Z I S Matrix 25 E G G G S Chinese 25 Q M P S X Codabar F N X N F Code 93 I L L L G Code 128 H K K K C ISBT 128 H K K K C UPC-E S E C E E EAN-8 P B B FF E EAN-13 M A A F E UPC-A J A A A E MSI V V D P M UCC Coupon Co
PAGE 143
Chapter 4 Defining Output Format MicroQR f T R Y Q Aztec g U Q Z z IATA z z r h S Macro PDF417 p i a q L Macro MicroPDF417 q j b r L 131 Update
PAGE 144
1504 Barcode Scanner User Guide 4.4.2 CHANGE CODE ID 1) Read the barcode below to change code ID of a specific symbology. 2) Read the “Hexadecimal Value” barcode on page 194 for the desired character string. For example, read “4” and “4” for applying the character [D] for Code ID. 3) Read the “Validate” barcode to complete this setting.
PAGE 145
Chapter 4 Defining Output Format Configure Code ID for Interleaved 25 Configure Code ID for Matrix 25 Configure Code ID for Chinese 25 Configure Code ID for MSI Configure Code ID for UPC-A Configure Code ID for UPC-E Configure Code ID for UCC Coupon Code Configure Code ID for Code 11 Configure Code ID for Composite CC-A/B Configure Code ID for Composite CC-C Configure Code ID for Composite TLC-39 Configure Code ID for US Postnet 133 Update
PAGE 146
1504 Barcode Scanner User Guide Configure Code ID for US Planet Configure Code ID for UK Postal Configure Code ID for Japan Postal Configure Code ID for Australian Postal Configure Code ID for Dutch Postal Configure Code ID for USPS 4CB / One Code / Intelligent Mail Configure Code ID for UPU FICS Postal Configure Code ID for PDF417 Configure Code ID for MicroPDF417 Configure Code ID for Data Matrix Configure Code ID for Maxicode Configure Code ID for QR Code 134 Enter Setup
PAGE 147
Chapter 4 Defining Output Format Configure Code ID for MicroQR Configure Code ID for Aztec Configure Code ID for IATA Configure Code ID for Macro PDF417 Configure Code ID for Macro MicroPDF417 4.4.
PAGE 148
1504 Barcode Scanner User Guide 4.5 LENGTH CODE A 4-digit code representing the length of barcode data (character count) can be inserted in front of data being transmitted. Such "Length" code can be individually enabled or disabled for each symbology.
PAGE 149
Chapter 4 Defining Output Format Length Code for Code 128 Apply *Do Not Apply Length Code for GS1-128 & GS1 DataBar Apply *Do Not Apply Length Code for ISBT 128 Apply *Do Not Apply Length Code for EAN-8 Apply *Do Not Apply Length Code for EAN-13 Apply *Do Not Apply 137 Update
PAGE 150
4 Barcode Scanner User Guide Length Code for Italian Pharmacode Apply *Do Not Apply Length Code for Industrial 25 Apply *Do Not Apply Length Code for Interleaved 25 Apply *Do Not Apply Length Code for Matrix 25 Apply *Do Not Apply Length Code for Chinese 25 Apply *Do Not Apply 138 Enter Setup
PAGE 151
Chapter 4 Defining Output Format Length Code for MSI Apply *Do Not Apply Length Code for UPC-A Apply *Do Not Apply Length Code for UPC-E Apply *Do Not Apply Length Code for UCC Coupon Extended Code Apply *Do Not Apply Length Code for Code 11 Apply *Do Not Apply 139 Update
PAGE 152
1504 Barcode Scanner User Guide Length Code for Composite CC-A/B Apply *Do Not Apply Length Code for Composite CC-C Apply *Do Not Apply Length Code for Composite TLC-39 Apply *Do Not Apply Length Code for US Postnet Apply *Do Not Apply Length Code for US Planet Apply *Do Not Apply 140 Enter Setup
PAGE 153
Chapter 4 Defining Output Format Length Code for UK Postal Apply *Do Not Apply Length Code for Japan Postal Apply *Do Not Apply Length Code for Australian Postal Apply *Do Not Apply Length Code for Dutch Postal Apply *Do Not Apply Length Code for USPS 4CB/One Code/Intelligent Mail Apply *Do Not Apply 141 Update
PAGE 154
1504 Barcode Scanner User Guide Length Code for UPU FICS Postal Apply *Do Not Apply Length Code for PDF417 Apply *Do Not Apply Length Code for MicroPDF417 Apply *Do Not Apply Length Code for Data Matrix Apply *Do Not Apply Length Code for Maxicode Apply *Do Not Apply 142 Enter Setup
PAGE 155
Chapter 4 Defining Output Format Length Code for QR Code Apply *Do Not Apply Length Code for MicroQR Apply *Do Not Apply Length Code for Aztec Apply *Do Not Apply 143 Update
PAGE 156
1504 Barcode Scanner User Guide 4.6 MULTI-BARCODE EDITOR The Multi-Barcode Editor allows deciding the output sequence of a concatenation of barcodes. Up to five barcodes can be specified. When enable this mode, it will force the scanner to apply Laser mode as the scan mode. For 1504 to concatenate barcodes, the maximum output data length of all the barcodes is 10 KB after configuration. When the data length exceeds 10 KB, the concatenation will not take effect.
PAGE 157
Chapter 4 Defining Output Format 4.6.1 EDIT A CONCATENATION OF BARCODES Edit Output Sequence 1) Read the barcode above to start editing a concatenation of barcodes. 2) Code Type setting – read the “Hexadecimal Value” barcode on page 194 for Code Type of the (first) barcode. For example, read “4” and “1” for Code 39.
PAGE 158
1504 Barcode Scanner User Guide 79 (y) Chinese 25 5A (Z) N/A 7A (z) Aztec 5B ( [ ) GS1 DataBar (RSS) 7B ({) Micro QR 7C (|) USPS 4CB / One Code / Intelligent Mail 7D (}) UPU FICS Postal 7E (~) UCC Coupon Extended Code 3) Barcode Length setting – read the “Decimal Value” barcode on page 193 for the 4-digit length of the (first) barcode. For example, read “0065” for barcode length of 65 characters or read “0000” for any length.
PAGE 159
Chapter 4 Defining Output Format 4.6.2 ACTIVATE THE CONCATENATION OF BARCODES By default, the output sequence editing of the concatenation of barcodes is not applied. When “Enforce Output Sequence” is enabled, all barcodes read by the scanner must meet with the criteria for the concatenation. If data is found excluded from all output sequence sets (= not meeting with the criteria), the scanner will not accept the reading, and therefore, data will not be transmitted.
PAGE 160
1504 Barcode Scanner User Guide 4.7 REMOVAL OF SPECIAL CHARACTER Specify only 1 character, but it will remove every matching character encountered from the starting position of barcode data until a different character is met. For example, if it is configured to remove the character “0” (hex value is “30”), one or more zeros will be stripped off the barcode data “012345” and “00012345”. However, for barcode data “010333”, only the first zero will be stripped off.
PAGE 161
Chapter 5 APPLYING FORMATS FOR DATA EDITING The scanner allows advanced data editing by applying user-configured editing formats. The whole processed data can be divided into fields by user-specified rules. These fields together with the user-configurable additional fields consist of the data actually sent to the host computer. For 1504 to apply any editing format, the maximum output data length of a barcode is 7 KB after configuration. When the data length exceeds 7 KB, editing format will not take effect.
PAGE 162
1504 Barcode Scanner User Guide 5.1 ACTIVATING EDITING FORMATS 5.1.1 ACTIVATE EDITING FORMATS If having already configured any editing format before, it may directly apply the editing format. If not, it must start with configuring an editing format first, and then, activate the editing format when it is desired in use.
PAGE 163
Chapter 5 Applying Formats for Data Editing Editing Format 5 Enable *Disable 5.1.2 EXCLUSIVE DATA EDITING By default, only barcodes found meeting with the criteria are processed by the editing formats. Those found not meeting with the criteria are processed normally. When “Exclusive Data Editing” is enabled, all barcodes read by the scanner must be processed by the editing formats.
PAGE 164
1504 Barcode Scanner User Guide 5.
PAGE 165
Chapter 5 Applying Formats for Data Editing 5.2.1 SELECT FORMAT TO CONFIGURE Start Programming Format Select one editing format (Format 1~5) and the parameters pertaining to the editing format can then be configured – applicable code type, data length, matching string & location, start position, field adjustment, total number of fields, field settings (field-dividing rule), additional fields, and field transmission sequence. Up to five different formats can be specified.
PAGE 166
1504 Barcode Scanner User Guide 5.2.2 RESTORE DEFAULT FORMAT Select an existing editing format and have the defaults restored. The default settings of an editing format are listed below.
PAGE 167
Chapter 5 Applying Formats for Data Editing 5.3 CONFIGURING FORMAT — DEFINE DATA CRITERIA Three applicable conditions can be configured to check whether the data read by the scanner can be processed by the particular editing format. Note: Data editing cannot be performed unless the three conditions are all met. 5.3.1 APPLICABLE CODE TYPE By default, barcodes of all the supported symbologies will be processed by any editing format, if having been configured and enabled.
PAGE 168
1504 Barcode Scanner User Guide Editing Format for Codabar *Apply Do Not Apply Editing Format for Code 39 *Apply Do Not Apply Editing Format for Trioptic Code 39 *Apply Do Not Apply Editing Format for Code 93 *Apply Do Not Apply Editing Format for Code 128 *Apply Do Not Apply 156 End Programming Format
PAGE 169
Chapter 5 Applying Formats for Data Editing Editing Format for GS1-128 & GS1 DataBar *Apply Do Not Apply Editing Format for ISBT 128 *Apply Do Not Apply Editing Format for EAN-8 *Apply Do Not Apply Editing Format for EAN-8 Addon 2 *Apply Do Not Apply Editing Format for EAN-8 Addon 5 *Apply Do Not Apply 157 Update
PAGE 170
1504 Barcode Scanner User Guide Editing Format for EAN-13 *Apply Do Not Apply Editing Format for EAN-13 Addon 2 *Apply Do Not Apply Editing Format for EAN-13 Addon 5 *Apply Do Not Apply Editing Format for Italian Pharmacode *Apply Do Not Apply Editing Format for Industrial 25 *Apply Do Not Apply 158 End Programming Format
PAGE 171
Chapter 5 Applying Formats for Data Editing Editing Format for Interleaved 25 *Apply Do Not Apply Editing Format for Matrix 25 *Apply Do Not Apply Editing Format for Chinese 25 *Apply Do Not Apply Editing Format for MSI *Apply Do Not Apply Editing Format for UPC-A *Apply Do Not Apply 159 Update
PAGE 172
1504 Barcode Scanner User Guide Editing Format for UPC-A Addon 2 *Apply Do Not Apply Editing Format for UPC-A Addon 5 *Apply Do Not Apply Editing Format for UPC-E *Apply Do Not Apply Editing Format for UPC-E Addon 2 *Apply Do Not Apply Editing Format for UPC-E Addon 5 *Apply Do Not Apply 160 End Programming Format
PAGE 173
Chapter 5 Applying Formats for Data Editing Editing Format for UCC Coupon Extended Code *Apply Do Not Apply Editing Format for Code 11 *Apply Do Not Apply Editing Format for Composite CC-A/B *Apply Do Not Apply Editing Format for Composite CC-C *Apply Do Not Apply Editing Format for Composite TLC-39 *Apply Do Not Apply 161 Update
PAGE 174
1504 Barcode Scanner User Guide Editing Format for US Postnet *Apply Do Not Apply Editing Format for US Planet *Apply Do Not Apply Editing Format for UK Postal *Apply Do Not Apply Editing Format for Japan Postal *Apply Do Not Apply Editing Format for Australian Postal *Apply Do Not Apply 162 End Programming Format
PAGE 175
Chapter 5 Applying Formats for Data Editing Editing Format for Dutch Postal *Apply Do Not Apply Editing Format for USPS 4CB/One Code/Intelligent Mail *Apply Do Not Apply Editing Format for UPU FICS Postal *Apply Do Not Apply Editing Format for PDF417 *Apply Do Not Apply Editing Format for MicroPDF417 *Apply Do Not Apply 163 Update
PAGE 176
1504 Barcode Scanner User Guide Editing Format for Data Matrix *Apply Do Not Apply Editing Format for Maxicode *Apply Do Not Apply Editing Format for QR Code *Apply Do Not Apply Editing Format for MicroQR *Apply Do Not Apply Editing Format for Aztec *Apply Do Not Apply 164 End Programming Format
PAGE 177
Chapter 5 Applying Formats for Data Editing 5.3.2 DATA LENGTH The length must include prefix, suffix (0x0d by default), length code, etc. By default, barcodes of any length (character count) are eligible for data editing. Specify a value. When zero is given to both, the scanner will not perform the length qualification. 1) Read the barcode below to specify Max. Length or Min. Length separately, and follow steps 2~3. Max. Length Min.
PAGE 178
1504 Barcode Scanner User Guide 5.3.3 MATCHING STRING & LOCATION By default, no matching string is specified, and therefore, it is disabled. Enable this feature by specifying a matching string; up to four characters are allowed. When the Matching String Location is zero, the scanner will only check for the existence of the matching string in the barcode data. Specify a value to indicate where the matching string starts in the barcode data. 1) Read the barcode to specify a matching string.
PAGE 179
Chapter 5 Applying Formats for Data Editing 5.4 CONFIGURING FORMAT — DEFINE DATA FIELD 5.4.1 START POSITION Data can be divided into fields in one of the following direction – from head (F1) to tail (F5) from tail (F1) to head (F5) *From Head From Tail 5.4.2 FIELD ADJUSTMENT Apply equal length to all fields, if necessary. If data is found longer than specified, it will be truncated automatically. When data is found shorter, it will add “Space” (0x20) to field.
PAGE 180
1504 Barcode Scanner User Guide 5.4.3 TOTAL NUMBER OF FIELDS Data can be divided into at most 6 fields; each of them is numbered from F1 to F6 accordingly. However, only F1~F5 can be configured. The total number of fields must be specified correctly. If three fields are configured for the editing format, the data characters after F3 will be assigned to F4 automatically. This feature is quite useful especially when data of variable lengths is processed by editing formats.
PAGE 181
Chapter 5 Applying Formats for Data Editing 5.4.4 FIELD SETTINGS Data eligible for editing formats is divided into fields by user-specified rules – either using the field terminating string or specified field length. By Terminating String Specify the field terminating string. Up to two characters are allowed. The scanner will search for the occurrence of this particular string in the data. By default, this string will be included in the field. By Length Alternatively, Simply specify the field length.
PAGE 182
1504 Barcode Scanner User Guide Field 2 Setting 1. Read the barcode below to divide field 2 by a specified terminating string. Select Field Separator to Divide Field 2… 2. Read the “Hexadecimal Value” barcode on page 194 for the desired character string. 3. Read the “Validate” barcode to complete this setting. 4. Read the “Discard Separator” barcode if the field separator is not desired in the field.
PAGE 183
Chapter 5 Applying Formats for Data Editing Field 3 Setting 1. Read the barcode below to divide field 3 by a specified terminating string. Select Field Separator to Divide Field 3… 2. Read the “Hexadecimal Value” barcode on page 194 for the desired character string. 3. Read the “Validate” barcode to complete this setting. 4. Read the “Discard Separator” barcode if the field separator is not desired in the field.
PAGE 184
1504 Barcode Scanner User Guide Field 4 Setting 1. Read the barcode below to divide field 4 by a specified terminating string. Select Field Separator to Divide Field 4… 2. Read the “Hexadecimal Value” barcode on page 194 for the desired character string. 3. Read the “Validate” barcode to complete this setting. 4. Read the “Discard Separator” barcode if the field separator is not desired in the field.
PAGE 185
Chapter 5 Applying Formats for Data Editing Field 5 Setting 1. Read the barcode below to divide field 5 by a specified terminating string. Select Field Separator to Divide Field 5… 2. Read the “Hexadecimal Value” barcode on page 194 for the desired character string. 3. Read the “Validate” barcode to complete this setting. 4. Read the “Discard Separator” barcode if the field separator is not desired in the field.
PAGE 186
1504 Barcode Scanner User Guide Additional Fields Up to five additional fields can be created for each editing format; each of them is numbered from AF1 to AF5 accordingly. If “Keyboard Wedge” or “USB HID” is configured for interface, Key Type and Key Status will then become applicable. Decide whether to apply Key Status when “Normal Key” is selected for Key Type. Key Type Key Status Scan Code Up to 2 scan code values are allowed. N/A Normal Key Up to 4 character strings are allowed.
PAGE 187
Chapter 5 Applying Formats for Data Editing 5.4.5 PAUSE FIELD SETTING Pause Field Time Limit the pause time interval (1~16). By default, it is set to 1 second. Pause Field Time 1~16 sec. (*1) 1. Read the barcode above to specify the time interval for the Pause Field. (It is set to 1 by default.) 2. Read the “Decimal Value” barcode on page 193. For example, read “1” and “0” for setting the Pause Field Time to 10 seconds. 3. Read the “Validate” barcode on the same page to complete this setting.
PAGE 188
1504 Barcode Scanner User Guide 5.5 CONFIGURING FORMAT — DEFINE TRANSMISSION SEQUENCE After configuring the data fields and additional fields, it must now program the transmission sequence of these fields that comprise the final data. This field transmission sequence can be assigned in any desired order and fields can be assigned multiple times as well. Note: Up to twelve fields can be assigned. 4) Read the “Start” barcode to begin with programming the field transmission sequence.
PAGE 189
Chapter 5 Applying Formats for Data Editing Additional Field 2 Additional Field 3 Additional Field 4 Additional Field 5 Pause Field Null Character Field 6) Read the “End” barcode to complete this setting.
PAGE 190
1504 Barcode Scanner User Guide 5.6 PROGRAMMING EXAMPLES 5.6.1 EXAMPLE I Extract data from the 10th character to the 19th character... The editing format should be configured as follows: 1. Read the “Enter Setup” barcode to enter the Configuration Mode. 2. Read the “Configure Format 1” barcode. 3. Read the “Clear All” and “Code 128” barcodes for applicable code type. 4. Read the “Three Fields” barcode. 5. Read the “Divide Field 1 by Length” barcode, and set length to 9.
PAGE 191
Chapter 5 Applying Formats for Data Editing 5.6.2 EXAMPLE II Extract the date code, item number, and quantity information from barcodes. Data in a barcode is encoded like this: From the 1st character to the 6th character is the date code. From the 7th character to the dash ‘-’ character is the item number. After the dash ‘-’ character is the quantity information.
PAGE 192
1504 Barcode Scanner User Guide 180 End Programming Format
PAGE 193
SPECIFICATIONS Optical Characteristics 1504 Scan Engine 2D Imager Light Source Visible red LED Physical Characteristics Switch Tactile switch Indication Dual-color LED (Red/Green) and beeper Interface Options Keyboard Wedge, RS-232, USB HID, USB Virtual COM Weight Approx.
PAGE 194
1504 Barcode Scanner User Guide Resistance Impact Resistance 1.2 m, 5 drops per 6 sides Splash / Dust Resistance IP 30 Electrostatic Discharge ± 15 kV air discharge, ± 8 kV contact discharge Programming Support Configuration via Setup Barcodes Use setup barcodes or host serial commands. Software Windows®-based ScanMaster Firmware upgradeable Download firmware updates via the download utility.
PAGE 195
Appendix I FIRMWARE UPGRADE USING RS-232 1) Connect the RS-232 cable between the scanner and the computer, and join the power supply cord. 2) Read the following barcodes in sequence to configure the scanner to use RS-232 as download interface. Enter Setup Activate RS-232 115200 bps Update 3) Read the following barcodes in sequence for the scanner to enter the download mode. The scanner will respond with beeps to indicate it is ready for downloading.
PAGE 196
1504 Barcode Scanner User Guide 4) Run the download utility “ProgLoad.exe” on the computer. Kernel Program User Program K150x_V*.shx STD150x_V*.shx For the communication settings, select “RS-232” and the correct COM port for RS-232 or USB Virtual COM interface. For RS-232, select 115200 bps for baud rate; for USB Virtual COM, ignore the baud rate setting. For the file option, click [Browse] to select the target file for firmware update. Click [OK].
PAGE 197
Appendix I Firmware Upgrade USING USB VIRTUAL COM 1) Connect the USB cable between the scanner and the computer. If using USB Virtual COM for the first time, it must install its driver from the CD-ROM. 2) For Windows platform, read the following barcodes in sequence to configure the scanner to use USB VCOM_CDC as download interface.
PAGE 198
1504 Barcode Scanner User Guide 4) Run the download utility “ProgLoad.exe” on the computer. Kernel Program User Program K150x_V*.shx STD150x_V*.shx For the communication settings, select “RS-232” and the correct COM port for RS-232 or USB Virtual COM interface. For RS-232, select 115200 bps for baud rate; for USB Virtual COM, ignore the baud rate setting. For the file option, click [Browse] to select the target file for firmware update. Click [OK].
PAGE 199
Appendix II HOST SERIAL COMMANDS SERIAL COMMANDS D Purpose To disable the scanner. Remarks “D” E Purpose To enable the scanner. Remarks “E” #@ nnnnnn Purpose To configure the scanner. Remarks nnnnnn – the six digits of command parameters. For example, “109952” is to list the current Code ID settings.
PAGE 200
1504 Barcode Scanner User Guide #@TRIGOFF Purpose Disable software trigger Remarks “0x23” + “0x40” + “0x54” + “0x52” + “0x49” + “0x47” + “0x4f” + “0x46” + “0x46” + “0x0d” #@TRIGON Purpose Enable software trigger Remarks “0x23” + “0x40” + “0x54” + “0x52” + “0x49” + “0x47” + “0x4f” + “0x4e” + “0x0d” EXAMPLE Run HyperTerminal.exe on the host computer to send serial commands to the scanner via RS-232 or USB Virtual COM.
PAGE 201
Appendix III KEYBOARD WEDGE TABLE “Apply” Special Keyboard 0 0 1 2 3 4 5 6 7 F2 SP 0 @ P ` p 1 INS F3 ! 1 A Q a q 2 DLT F4 " 2 B R b r 3 Home F5 # 3 C S c s 4 End F6 $ 4 D T d t 5 Up F7 % 5 E U e u 6 Down F8 & 6 F V f v 7 Left F9 ' 7 G W g w 8 BS F10 ( 8 H X h x 9 HT F11 ) 9 I Y i y A LF F12 * : J Z j z B Right ESC + ; K [ k { C PgUp Exec , < L \ l | D CR CR* - = M ] m } E PgD
PAGE 202
1504 Barcode Scanner User Guide “Bypass” Special Keyboard 0 1 2 3 4 5 6 7 0 SP 0 @ P ` p 1 ! 1 A Q a q 2 " 2 B R b r 3 # 3 C S c s 4 $ 4 D T d t 5 % 5 E U e u 6 & 6 F V f v 7 ' 7 G W g w 8 BS ( 8 H X h x 9 HT ) 9 I Y i y A LF * : J Z j z + ; K [ k { , < L \ l | - = M ] m } E . > N ^ n ~ F / ? O _ o Dly B ESC C D CR Note: (1) ~ : Digits of numeric keypad.
PAGE 203
Appendix III Keyboard Wedge Table KEY TYPE & STATUS KEY TYPE If “Keyboard Wedge” or “USB HID” is configured for interface, Key Type and Key Status will then become applicable. *Normal Scan Code KEY STATUS Decide whether or not to change key status when “Normal Key” is selected for Key Type.
PAGE 204
1504 Barcode Scanner User Guide EXAMPLE KEY TYPE = NORMAL For example, if want to program the character “!” as the prefix code: 1. Read the “Configure Prefix” barcode. 2. Read the “Hexadecimal Value” barcode on page 194 for “2” and “1”. 3. Read the “Validate” barcode to complete this setting. KEY TYPE = SCAN CODE For example, if want to program the character “a” (= “1C” on the scan code table) as the prefix code: 1. Read the “Configure Prefix” barcode. 2. Read the “Scan Code” barcode. 3.
PAGE 205
Appendix IV NUMERAL SYSTEMS DECIMAL SYSTEM Decimal 0 1 2 3 4 5 6 7 8 9 Validate the Values Validate Update Abort 193
PAGE 206
1504 Barcode Scanner User Guide HEXADECIMAL SYSTEM Hexadecimal 0 1 2 3 4 5 6 7 8 9 A B C D E F 194 Enter Setup
PAGE 207
Appendix IV Numeral Systems Validate the Values Validate ASCII TABLE 0 0 1 2 3 4 5 6 7 DLE SP 0 @ P ` p 1 SOH DC1 ! 1 A Q a q 2 STX DC2 " 2 B R b r 3 ETX DC3 # 3 C S c s 4 EOT DC4 $ 4 D T d t 5 ENQ NAK % 5 E U e u 6 ACK SYN & 6 F V f v 7 BEL ETB ' 7 G W g w 8 BS CAN ( 8 H X h x 9 HT EM ) 9 I Y i y A LF SUB * : J Z j z B VT ESC + ; K [ k { C FF FS , < L \ l | D CR GS - = M ] m
PAGE 208
Appendix V READING DRIVER LICENSES 1504 is capable of reading 2D driver’s licenses and other American Association of Motor Vehicle Administrators (AAMVA) compliant ID cards. For compliant 2D licensed card scanning, it decodes the information embedded in the ID cards to a formatted data. This appendix provides the setup barcodes required while ScanMaster utility provides GUI setup that is oganized and easy-to-use.
PAGE 209
Appendix V Reading Driver Licenses OUTPUT SEQUENCE SETUP 1504 supports arranging the sequences of license embedded data via separators and fields. In order to present data in a consistent format, some barcodes (ex. First Name, Middle Name/Initial, Last Name, Name suffix, Name Prefix, Birth Date and so on) will return data based on the calculated actual data contained in the ID barcode.
PAGE 210
1504 Barcode Scanner User Guide Mailing Address Postal Code Home Address Line1 Home Address Line2 Home Address City Home Address State Home Address Postal Code License ID Number License Class License Restrictions License Endorsements Height (Feet and/or Inches) Height (Centimeters) 198 Enter Setup
PAGE 211
Appendix V Reading Driver Licenses Weight (Pounds) Weight (Kilograms) Eye Color Hair Color License Expiration Date Birth Date Gender License Issue Date Issue Timestamp Number of Duplicates Medical Codes Organ Donor Update Abort 199
PAGE 212
1504 Barcode Scanner User Guide Nonresident Customer ID Social Security Number AKA Birth Date AKA Social Security Name AKA Full Name AKA Last Name AKA First Name AKA Middle Name/Initial AKA Name Suffix AKA Name Prefix Weight Range 200 Enter Setup
PAGE 213
Appendix V Reading Driver Licenses Document Discriminator Country Federal Commission Codes Place of Birth Audit Information Inventory Control Race/Ethnicity Std Vehicle Class Std Restrictions Std Endorsements Class Description Endorsement Description Update Abort 201
PAGE 214
1504 Barcode Scanner User Guide Restrictions Description Permit Class Permit Expiration Date Permit ID Number Permit Issue Date Permit Restrictions Permit endorsements Issuer ID Number 202 Enter Setup
PAGE 215
Appendix V Reading Driver Licenses SEPARATORS AND FIELDS Define the separators that separate fields during the transmission sequence of data scanning. In addition to the built-in data elements, you can also specify up to 5 Additional Fields with 4 bytes characters. Program the transmission sequence by reading the desired fields as additional fields. Note: Up to 5 separators can be assigned. Separator 1 (1 byte) *“Space” Separator 2 (1 byte) *“Enter” Separator 3 (1 byte) *“,” Separator 4 (1 byte) *“.
PAGE 216
1504 Barcode Scanner User Guide EDIT SEPARATORS All the driver license fields can be split with a pre-selected separator, for example, “-” as First Name-Last Name or “:” as First Name:Last Name. Edit Separator 1 Edit Separator 2 Edit Separator 3 Edit Separator 4 Edit Separator 5 1) Read the barcode above to apply separator to driver license information separately, and follow steps 2~3. 2) Read the “Hexadecimal Value” barcode for the desired character string.
PAGE 217
Appendix V Reading Driver Licenses EDIT FIELDS Up to five additional fields can be created for each editing format; each of them is numbered from Additional 1 to Additional 5 accordingly. If “Bluetooth® HID” or “USB HID” is configured for interface, Key Type and Key Status will then become applicable. You may decide whether or not to apply Key Status when “Normal Key” is selected for Key Type. Key Type Key Status Scan Code Up to 2 scan code values are allowed.