User manual
Table Of Contents
- About this manual
- What’s included
- Safety information
- Support information
- Hardware I/O
- Basic operation
- User Interface
- General notes about the user interface
- Main user interface (recording)
- Record start [record]
- Record stop [stop]
- Wired remote record start/stop [start][stop]
- Slate display [slate] Not currently enabled.
- Safe Frame Display [safe]
- Grid Display [grid]
- 100% Display [100%]
- Edge detection display [edge]
- Image Analysis [analysis]
- Highlight Clipping [clipping]
- Full Screen display [fullscreen]
- Full screen mode in main user interface [fullscreen]
- Full screen mode in main user interface [fullscreen]
- Full screen mode in playback interface. [fullscreen]
- Setup Menu Tabs [setup]
- Playback user interface [play]
- Playback user interface [play]
- Playback file manager [play]:[open]
- Touch screen lock [lock]
- Time Code Reset [TC reset]
- Settings and Status displays
- Playback user interface
- Setup Menu Tabs [setup]
- Input preferences tab [setup]:[input]
- Input preferences tab [setup]:[input]
- Signal input settings [setup]:[input] or {input status display}
- Valid input selections
- Application restart on settings change
- Application restart on settings change
- Input resolution
- Input frame rate
- Input pixel format
- Input video source
- Input audio source
- Input preview options
- Input codec, quality, and file format (wrapper) options
- Input preferences tab [setup]:[input]
- Folder manager tab [setup]:[files]
- Time code Preferences Tab [setup][TC]
- Time code Preferences Tab [setup][TC]
- Internally generated time code [gen]
- Save time code at end of session. [save TC]
- Generated drop frame time code [drop]
- Embedded SDI time code [SDI]
- Embedded SDI time code auto-record, generic [generic]
- Embedded SDI time code auto-record, VITC [future]
- ExSync hardware timecode module [ExSync]
- Hardware timecode module not found
- Time code offsets [offset +][offset -]
- Time code offsets [offset +][offset -]
- Time code display modes
- Show UTC or Local timecode [show UTC][show local]
- Time code Preferences Tab [setup][TC]
- Convert preferences tab [setup][convert]
- Update preferences tab [setup][update]
- General preferences tab [setup][prefs]
- Input preferences tab [setup]:[input]
- Appendices:
- Field Operating System Restore (“Factory Reset”) Instructions:
- Cinedeck Operating System Field Restore Disk Update instructions
- Cinedeck Bootable BIOS Update Disk Creation Instructions
- Breakout cable connections
- Cinedeck I/O Pin Definitions: Serial numbers 500 and higher.
- Setting up the docking station for use with the Cinedeck Extreme
- Care and feeding of SSD media
- Setting the battery meter COM port
- Codec installation on the MAC and PC
- Average data rates
P not Psf
Peak vu
mouse exit
low
high
Digi View
exit app grid
clip
reset prefs
save prefs
load prefs
restart app
Anton Bauer
mouse
input files TC conv input
GPS
Disable Safe
3Gb/s out
3Gb/s out
drop stop fan ctrl
battery meter
med
mainloss stop
prefs
support@cinedeck.com Version 2.0 release build 2.177
Fan control enable (default on) Control only on during record.
[fan ctrl]
Sets target fan speed during record to low (default off)
[low]
Sets target fan speed during record to medium (default off)
[medium]
Auto sets fan speed to lowest setting available given current system temperature.
[auto]
Battery level monitoring enable. (default off)
[battery mon]
Selects Anton Bauer standard monitoring. (default off)
[Anton Bauer]
Selects IDX standard monitoring. (default off)
[Digi View]
Restarts the application. Useful for troubleshooting.
[restart app]
Exits the Cinedeck application to the Windows desktop.
[exit app]
Resets preferences to defaults. Useful for troubleshooting.
[reset prefs]
Saves preferences file to a USB thumb drive if inserted in USB port
[save prefs]
Loads preferences file from a USB thumb drive if inserted in USB port
[load prefs]
Sets target fan speed during record to high (default off)
[high]
Fan control, Battery monitor preferences, ap-
plication control, and save/load preferences.
Preferences is the default tab when setup is
invoked.
General Preferences [setup]:[prefs]
General preferences tab, continued [setup][prefs]
Prefs
fan ctrl
auto
medium
Anton Bauer
exit app
save prefs
low
battery mon
restart app
high
Digi View
reset prefs
load prefs