User manual
Table Of Contents
- About this manual
- What’s included
- Safety information
- Support information
- Hardware I/O
- Basic operation
- User Interface
- General notes about the user interface
- Main user interface (recording)
- Record start [record]
- Record stop [stop]
- Wired remote record start/stop [start][stop]
- Slate display [slate] Not currently enabled.
- Safe Frame Display [safe]
- Grid Display [grid]
- 100% Display [100%]
- Edge detection display [edge]
- Image Analysis [analysis]
- Highlight Clipping [clipping]
- Full Screen display [fullscreen]
- Full screen mode in main user interface [fullscreen]
- Full screen mode in main user interface [fullscreen]
- Full screen mode in playback interface. [fullscreen]
- Setup Menu Tabs [setup]
- Playback user interface [play]
- Playback user interface [play]
- Playback file manager [play]:[open]
- Touch screen lock [lock]
- Time Code Reset [TC reset]
- Settings and Status displays
- Playback user interface
- Setup Menu Tabs [setup]
- Input preferences tab [setup]:[input]
- Input preferences tab [setup]:[input]
- Signal input settings [setup]:[input] or {input status display}
- Valid input selections
- Application restart on settings change
- Application restart on settings change
- Input resolution
- Input frame rate
- Input pixel format
- Input video source
- Input audio source
- Input preview options
- Input codec, quality, and file format (wrapper) options
- Input preferences tab [setup]:[input]
- Folder manager tab [setup]:[files]
- Time code Preferences Tab [setup][TC]
- Time code Preferences Tab [setup][TC]
- Internally generated time code [gen]
- Save time code at end of session. [save TC]
- Generated drop frame time code [drop]
- Embedded SDI time code [SDI]
- Embedded SDI time code auto-record, generic [generic]
- Embedded SDI time code auto-record, VITC [future]
- ExSync hardware timecode module [ExSync]
- Hardware timecode module not found
- Time code offsets [offset +][offset -]
- Time code offsets [offset +][offset -]
- Time code display modes
- Show UTC or Local timecode [show UTC][show local]
- Time code Preferences Tab [setup][TC]
- Convert preferences tab [setup][convert]
- Update preferences tab [setup][update]
- General preferences tab [setup][prefs]
- Input preferences tab [setup]:[input]
- Appendices:
- Field Operating System Restore (“Factory Reset”) Instructions:
- Cinedeck Operating System Field Restore Disk Update instructions
- Cinedeck Bootable BIOS Update Disk Creation Instructions
- Breakout cable connections
- Cinedeck I/O Pin Definitions: Serial numbers 500 and higher.
- Setting up the docking station for use with the Cinedeck Extreme
- Care and feeding of SSD media
- Setting the battery meter COM port
- Codec installation on the MAC and PC
- Average data rates
offset -
offset +
show local
show UTC
gen off
Ambient VITC
input files convert prefsinput
plain
SDI
generic
TC
source mode auto rec offsets
back
off
offset -
offset +
show local
show UTC
gen
Ambient VITC
generic
input files convert prefsinput
plain
SDI
off
TC
source mode auto rec offsets
off
back
Embedded SDI time code auto-record, generic [generic]
Embedded SDI time code [SDI]
Generated drop frame time code [drop]
There are three sources of embedded time
code recognized in the embedded SDI stream:
LTC, RP188, Serial
Toggles internally generated time code. When
on, internally generated time code will be
displayed as SMPTE drop frame time code,
and drop frame time code will be saved into
the file.
Generated time code has three different run
types associated with it:
Record run [rec run] - starts at zero plus any
offsets, and increments only while record is
active.
Per take run [per take] - starts at zero on
each take, plus any offsets.
Free run [free run] - starts at zero and runs
until the session is terminated or the TC
reset slider is used.
Time code Preferences Tab, continued [setup][TC]
TC auto rec
TC
SDI
TC
drop
offset -
offset +
show local
show UTC
Ambient
SDI
input files convert prefsinput
gen
TC
source mode auto rec offsets
off
save tc drop
per take
rec run
free run
back