User manual
Table Of Contents
- About this manual
- What’s included
- Safety information
- Support information
- Hardware I/O
- Basic operation
- User Interface
- General notes about the user interface
- Main user interface (recording)
- Record start [record]
- Record stop [stop]
- Wired remote record start/stop [start][stop]
- Slate display [slate] Not currently enabled.
- Safe Frame Display [safe]
- Grid Display [grid]
- 100% Display [100%]
- Edge detection display [edge]
- Image Analysis [analysis]
- Highlight Clipping [clipping]
- Full Screen display [fullscreen]
- Full screen mode in main user interface [fullscreen]
- Full screen mode in main user interface [fullscreen]
- Full screen mode in playback interface. [fullscreen]
- Setup Menu Tabs [setup]
- Playback user interface [play]
- Playback user interface [play]
- Playback file manager [play]:[open]
- Touch screen lock [lock]
- Time Code Reset [TC reset]
- Settings and Status displays
- Playback user interface
- Setup Menu Tabs [setup]
- Input preferences tab [setup]:[input]
- Input preferences tab [setup]:[input]
- Signal input settings [setup]:[input] or {input status display}
- Valid input selections
- Application restart on settings change
- Application restart on settings change
- Input resolution
- Input frame rate
- Input pixel format
- Input video source
- Input audio source
- Input preview options
- Input codec, quality, and file format (wrapper) options
- Input preferences tab [setup]:[input]
- Folder manager tab [setup]:[files]
- Time code Preferences Tab [setup][TC]
- Time code Preferences Tab [setup][TC]
- Internally generated time code [gen]
- Save time code at end of session. [save TC]
- Generated drop frame time code [drop]
- Embedded SDI time code [SDI]
- Embedded SDI time code auto-record, generic [generic]
- Embedded SDI time code auto-record, VITC [future]
- ExSync hardware timecode module [ExSync]
- Hardware timecode module not found
- Time code offsets [offset +][offset -]
- Time code offsets [offset +][offset -]
- Time code display modes
- Show UTC or Local timecode [show UTC][show local]
- Time code Preferences Tab [setup][TC]
- Convert preferences tab [setup][convert]
- Update preferences tab [setup][update]
- General preferences tab [setup][prefs]
- Input preferences tab [setup]:[input]
- Appendices:
- Field Operating System Restore (“Factory Reset”) Instructions:
- Cinedeck Operating System Field Restore Disk Update instructions
- Cinedeck Bootable BIOS Update Disk Creation Instructions
- Breakout cable connections
- Cinedeck I/O Pin Definitions: Serial numbers 500 and higher.
- Setting up the docking station for use with the Cinedeck Extreme
- Care and feeding of SSD media
- Setting the battery meter COM port
- Codec installation on the MAC and PC
- Average data rates

file
Phones
back
fullscreen
clipping
analysis
edge
100%
grid
safe
slate
manhattan_aerial
reel_2_031
in/out
step
open
00:01:55:07
1080p YUV10
23.98
CineForm high
128GB
73GB
46 min
Frame
Fps
Codec
Media
Free
Remain
long
lat
alt
temp
-74.0715
40.416
51.166
72
Battery
last take
79%
2:54
Playback open menu thumbnails display and navigation.
Each take is labeled with the take number
and file type.
If there are more than 20 takes in the folder,
navigation arrows will appear.
The playback file manager allows selection
of the current folder for playback as well as
take deletion.
If there are no takes in the current project
folder, the project manager is opened by
default when [play] is selected from the main
interface.
If there are other projects or scenes with
takes, they can be opened from here.
If the current project or scene folder con-
tains no takes, the folders may be renamed
here as in the main file manager.
The open button invokes the playback file
manager.
Playback file manager open [open]
Playback user interface, cont.
Playback file manager open [open]
open
open
open
manhattan aerial
reel_5
reel_4
new project new scene
take delete back
reel_3
reel_2akbuk_farm
test
reel_1
To delete or rename Project/Scene folders:
1) Folders cannot have takes inside, they must be empty
2) “Disable safe” must be selected in the Prefs tab
3) “Take delete” button must be unselected
manhattan aerial
reel_5
reel_4
new project new scene
take delete back
reel_3
reel_2akbuk_farm
test
reel_1
To delete or rename Project/Scene folders:
1) Folders cannot have takes inside, they must be empty
2) “Disable safe” must be selected in the Prefs tab
3) “Take delete” button must be unselected