User manual
Table Of Contents
- About this manual
- What’s included
- Safety information
- Support information
- Hardware I/O
- Basic operation
- User Interface
- General notes about the user interface
- Main user interface (recording)
- Record start [record]
- Record stop [stop]
- Wired remote record start/stop [start][stop]
- Slate display [slate] Not currently enabled.
- Safe Frame Display [safe]
- Grid Display [grid]
- 100% Display [100%]
- Edge detection display [edge]
- Image Analysis [analysis]
- Highlight Clipping [clipping]
- Full Screen display [fullscreen]
- Full screen mode in main user interface [fullscreen]
- Full screen mode in main user interface [fullscreen]
- Full screen mode in playback interface. [fullscreen]
- Setup Menu Tabs [setup]
- Playback user interface [play]
- Playback user interface [play]
- Playback file manager [play]:[open]
- Touch screen lock [lock]
- Time Code Reset [TC reset]
- Settings and Status displays
- Playback user interface
- Setup Menu Tabs [setup]
- Input preferences tab [setup]:[input]
- Input preferences tab [setup]:[input]
- Signal input settings [setup]:[input] or {input status display}
- Valid input selections
- Application restart on settings change
- Application restart on settings change
- Input resolution
- Input frame rate
- Input pixel format
- Input video source
- Input audio source
- Input preview options
- Input codec, quality, and file format (wrapper) options
- Input preferences tab [setup]:[input]
- Folder manager tab [setup]:[files]
- Time code Preferences Tab [setup][TC]
- Time code Preferences Tab [setup][TC]
- Internally generated time code [gen]
- Save time code at end of session. [save TC]
- Generated drop frame time code [drop]
- Embedded SDI time code [SDI]
- Embedded SDI time code auto-record, generic [generic]
- Embedded SDI time code auto-record, VITC [future]
- ExSync hardware timecode module [ExSync]
- Hardware timecode module not found
- Time code offsets [offset +][offset -]
- Time code offsets [offset +][offset -]
- Time code display modes
- Show UTC or Local timecode [show UTC][show local]
- Time code Preferences Tab [setup][TC]
- Convert preferences tab [setup][convert]
- Update preferences tab [setup][update]
- General preferences tab [setup][prefs]
- Input preferences tab [setup]:[input]
- Appendices:
- Field Operating System Restore (“Factory Reset”) Instructions:
- Cinedeck Operating System Field Restore Disk Update instructions
- Cinedeck Bootable BIOS Update Disk Creation Instructions
- Breakout cable connections
- Cinedeck I/O Pin Definitions: Serial numbers 500 and higher.
- Setting up the docking station for use with the Cinedeck Extreme
- Care and feeding of SSD media
- Setting the battery meter COM port
- Codec installation on the MAC and PC
- Average data rates
play setup
fullscreen
clipping
analysis
edge
100%
grid
safe
slate
stop
record
lock reset
manhattan_aerial
next: reel_2_031
1080p YUV10
23.98
CineForm 1.1MB/frame 27.3MB/s
128GB
73GB
46 min
Frame
Fps
Codec
Media
Free
Remain
00:12:06:21
long
lat
alt
temp
-74.0715
40.416
51.166
72
Battery
last take
44%
3:22
SDI
Phones
play setup
fullscreen
clipping
analysis
edge
100%
grid
safe
slate
stop
record
lock reset
manhattan_aerial
next: reel_2_031
1080p YUV10
23.98
CineForm 1.1MB/frame 27.3MB/s
128GB
73GB
46 min
Frame
Fps
Codec
Media
Free
Remain
00:12:06:21
long
lat
alt
temp
-74.0715
40.416
51.166
72
Battery
last take
44%
3:22
SDI
Phones
play setup
fullscreen
clipping
analysis
edge
100%
grid
safe
slate
stop
record
lock reset
manhattan_aerial
next: reel_2_031
1080p YUV10
23.98
CineForm 1.1MB/frame 27.3MB/s
128GB
73GB
46 min
Frame
Fps
Codec
Media
Free
Remain
00:12:06:21
long
lat
alt
temp
-74.0715
40.416
51.166
72
Battery
last take
44%
3:22
SDI
Phones
Time Code Reset [TC reset]
When in internally generated time code mode,
resets the time code to zero: 00:00:00:00
If an offset is active, it sets timecode to zero
plus the offset. eg 01:00:00:00
The timecode reset is only relevant when in in-
ternally generated timecode, record run mode.
If in hardware or SDI time code mode, or in in-
ternally generated free run or per take modes,
the TC reset button will not be visible.
To reset, touch the [TC reset] button and
slide the popup slider to the right.
It is necessary to keep the stylus within the
borders of the slider or the unlock will not
register.
Main user interface, cont.
Time Code Reset Slider [TC reset]
To unlock, touch the lock button and slide
the popup slider to the right.
It is necessary to stay within the borders of
the slider or the unlock will not register.
TC reset
TC reset
lock