User manual
Table Of Contents
- About this manual
- What’s included
- Safety information
- Support information
- Hardware I/O
- Basic operation
- User Interface
- General notes about the user interface
- Main user interface (recording)
- Record start [record]
- Record stop [stop]
- Wired remote record start/stop [start][stop]
- Slate display [slate] Not currently enabled.
- Safe Frame Display [safe]
- Grid Display [grid]
- 100% Display [100%]
- Edge detection display [edge]
- Image Analysis [analysis]
- Highlight Clipping [clipping]
- Full Screen display [fullscreen]
- Full screen mode in main user interface [fullscreen]
- Full screen mode in main user interface [fullscreen]
- Full screen mode in playback interface. [fullscreen]
- Setup Menu Tabs [setup]
- Playback user interface [play]
- Playback user interface [play]
- Playback file manager [play]:[open]
- Touch screen lock [lock]
- Time Code Reset [TC reset]
- Settings and Status displays
- Playback user interface
- Setup Menu Tabs [setup]
- Input preferences tab [setup]:[input]
- Input preferences tab [setup]:[input]
- Signal input settings [setup]:[input] or {input status display}
- Valid input selections
- Application restart on settings change
- Application restart on settings change
- Input resolution
- Input frame rate
- Input pixel format
- Input video source
- Input audio source
- Input preview options
- Input codec, quality, and file format (wrapper) options
- Input preferences tab [setup]:[input]
- Folder manager tab [setup]:[files]
- Time code Preferences Tab [setup][TC]
- Time code Preferences Tab [setup][TC]
- Internally generated time code [gen]
- Save time code at end of session. [save TC]
- Generated drop frame time code [drop]
- Embedded SDI time code [SDI]
- Embedded SDI time code auto-record, generic [generic]
- Embedded SDI time code auto-record, VITC [future]
- ExSync hardware timecode module [ExSync]
- Hardware timecode module not found
- Time code offsets [offset +][offset -]
- Time code offsets [offset +][offset -]
- Time code display modes
- Show UTC or Local timecode [show UTC][show local]
- Time code Preferences Tab [setup][TC]
- Convert preferences tab [setup][convert]
- Update preferences tab [setup][update]
- General preferences tab [setup][prefs]
- Input preferences tab [setup]:[input]
- Appendices:
- Field Operating System Restore (“Factory Reset”) Instructions:
- Cinedeck Operating System Field Restore Disk Update instructions
- Cinedeck Bootable BIOS Update Disk Creation Instructions
- Breakout cable connections
- Cinedeck I/O Pin Definitions: Serial numbers 500 and higher.
- Setting up the docking station for use with the Cinedeck Extreme
- Care and feeding of SSD media
- Setting the battery meter COM port
- Codec installation on the MAC and PC
- Average data rates
SDI
Phones
play setup
fullscreen
clipping
analysis
edge
100%
grid
safe
slate
stop
record
lock reset
manhattan_aerial
next: reel_2_031
1080p YUV10
23.98
CineForm 1.1MB/frame 27.3MB/s
128GB
73GB
46 min
Frame
Fps
Codec
Media
Free
Remain
00:12:06:21
long
lat
alt
temp
-74.0715
40.416
51.166
72
Battery
last take
44%
3:22
SDI
Phones
play setup
fullscreen
clipping
analysis
edge
100%
grid
safe
slate
stop
record
lock reset
manhattan_aerial
next: reel_2_031
1080p YUV10
23.98
CineForm 1.1MB/frame 27.3MB/s
128GB
73GB
46 min
Frame
Fps
Codec
Media
Free
Remain
00:12:06:21
long
lat
alt
temp
-74.0715
40.416
51.166
72
Battery
last take
44%
3:22
SDI
Phones
play setup
fullscreen
clipping
analysis
edge
100%
grid
safe
slate
record
lock reset
manhattan_aerial
next: reel_2_031
1080p YUV10
23.98
CineForm 1.1MB/frame 27.3MB/s
128GB
73GB
46 min
Frame
Fps
Codec
Media
Free
Remain
00:12:06:21
long
lat
alt
temp
-74.0715
40.416
51.166
72
Battery
last take
44%
3:22
Record start [record]
Record stop [stop]
Wired remote record start/stop [start][stop]
When in ‘wired remote’ mode,
[setup]:[prefs]:{rec/stop}the record button
also acts as the stop button.
Once record is engaged, the text in the re-
cord button will change to [stop]
To prevent accidental recordings, the button
must be held down for about 1/2 second be-
fore record will engage.
To prevent accidentally stopping the record-
ing, the button must be held down for about
1/2 second before stop will engage.
Main user interface, cont.
record
stop
stop
record