User manual

ManualsBrandsCine versum ManualsProjectorForce One 3D

15.0 MISCELLANEOUS

R599820 - Blackwing mk2013 User Manual 47

[4Ch 53 50h 54h] + 4 ASCII chars as new port address in hexa

LAN communication protocol and timed out

Examples

15.3 Infra Red, long hex-pronto compatible RCU

The infra red command must be sent using NEC 5 protocol in ASCII format.

In the following example, Power ON command is 37h 33h 30h 35h, this command has to be converted as ASCII, it

becomes 73 05.

To send this command using long hex Pronto compatible, convert the ASCII code as two hexadecimal numbers as

follow:

Code A: 73h = 115 (for code B: 63h = 99, replace 115 by 99)

05h = 5

Then program the Pronto RCU using the Device number 115 and Function 5:

Device Code: 115 (0x73) Function: 5 (0x05):

0000 006D 0001 0011 0141 00A0 0014 003C 0014 003C 0014 0014 0014 0014 0014 003C 0014 003C 0014 003C

0014 0014 0014 003C 0014 0014 0014 003C 0014 0014 0014 0014 0014 0014 0014 0014 0014 0014 0014 0336

A complete device/function chart with their corresponding long hex commands is available, ask your dealer if

required.

You want to set TCP port to 10000 Command to send (RS-232C)

Send 10000 as new TCP port value:

10000 is 2710h in hexa, converted in

ASCII characters: 32h 37h 31h 30h

send: 21h 89h 01h 4Ch 53h 50h 54h 32h 37h 31h 30h 0Ah

receive: 06h 89h 01h 4Ch 53h 0Ah (conﬁrm cmd)

Then, reboot Network module

send: 21h 89h 01h 4Ch 53h 52h 53h 0Ah

receive: 06h 89h 01h 4Ch 53h 0Ah (conﬁrm cmd)

You want to... Command to send

Switch the projector ON

1. open TCP connection

2. receive PJ_OK: 50h 4Ah 5Fh 4Fh 4Bh

3. send PJREQ: 50h 4Ah 52h 45h 51h

4. receive PJACK: 50h 4Ah 41h 43h 4Bh

5. send Power On cmd: 21h 89h 01h 52h 43h 37h 33h 30h 35h 0Ah

6. receive conﬁrmation: 06h 89h 01h 52h 43h 0Ah

after 5 sec, TCP connection is closed.

Switch Anamorphic to mode A

1. open TCP connection

2. receive PJ_OK: 50h 4Ah 5Fh 4Fh 4Bh

3. send PJREQ: 50h 4Ah 52h 45h 51h

4. receive PJACK: 50h 4Ah 41h 43h 4Bh

5. send Anamorphic A: 21h 89h 01h 52h 43h 37h 33h 32h 33h 0Ah

6. receive conﬁrmation: 06h 89h 01h 52h 43h 0Ah

after 5 sec, TCP connection is closed.

Control Device

Projector

1. Opening Connection

2. Projector Ready

3. Command Type

(PJREQ)

(PJ_OK)

4.Projector Acknowledge

(PJACK)

5. Command

6. Projector confirms

After 5sec, connection

is closed.

on port 20554