Installation Manual

ClareOne Door Window Sensor with Shock Installation Manual
CLR-C1-DWSHK
CLR-C1-DWSHK IM V3 05012020
marks with each other. Trip the sensor by pulling the
magnet away from the sensor. Monitor the system after
tripping the sensor. Refer to the specific panel
documentation for interpretation of the results to ensure
desired signal strength is achieved.
Battery Replacement
Note: If a low battery alarm occurs, replace the battery
within 7 days.
• Low battery detect. LED flashes until battery is
replaced. Device sends low battery signal to control
panel.
• The CLR-C1-DWSHK requires (2) 3-VDC, lithium coin-
cell batteries (Varta or Panasonic, Model CR2032).
Both batteries should be replaced at the same time.
1. Remove sensor cover by pressing on the latch
and pulling the cover off
2. Do not remove the circuit board, slide the old
batteries out as shown
3. Insert new batteries observing polarity
4. Replace sensor cover
CAUTION: Battery may explode if mistreated. Do not
recharge, disassemble or dispose of in fire.
Specifications
Model no.
CLR-C1-DWSHK
RF frequency
433.95 MHz
Compatibility
Clare Control Panels
Battery type
(2) 3-VDC, lithium coin-cell
battery (Varta or Panasonic,
Model CR2032)
Operating
temperature range
32 to 120°F (0 to 49°C)
Storage
temperature range
-30 to 140°F (-34 to 60°C)
Relative humidity
95% non-condensing
Dimensions
(L x W x D)
2.25 x 1.0 x 0.50 in.
FCC / IC Statement
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
Per FCC 15.19 (a) (3) and (a) (4), This device complies with part 15 of
the FCC Rules. Operation is subject to the following conditions: (1) this
device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesirable operation.
Per FCC 15.21, The user manual or instruction manual for an intentional
or unintentional radiator shall caution the user that changes or
modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Industry Canada license-exempt RSS
standard(s). Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation
of the device.
Cet appareil est conforme avec Industrie Canada exempts de licence
standard RSS (s). Son fonctionnement est soumis aux deux conditions
suivantes: (1) cet appareil ne doit pas provoquer d'interférences et (2)
cet appareil doit accepter toute interférence, y compris celles pouvant
causer un mauvais fonctionnement de l'appareil.
In accordance with FCC requirements of human exposure to radio
frequency fields, the radiating element shall be installed such that a
minimum separation distance of 20 cm is maintained from the general
population.
FCC: 2ABBZ-RF-SHK-433
IC: 11817A-RFSHK433
This Class B digital apparatus complies with Canadian ICES-3B.
Cet appareil numérique de la classe B est conforme à la norme NMB-
003 du Canada.
MANUFACTURER HEREBY DISCLAIMS ALL WARRANTIES AND
REPRESENTATIONS, WHETHER EXPRESS, IMPLIED, STATUTORY
OR OTHERWISE INCLUDING (BUT NOT LIMITED TO) ANY
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE WITH RESPECT TO THESE PRODUCTS
AND ANY RELATED SOFTWARE. MANUFACTURER FURTHER
DISCLAIMS ANY OTHER IMPLIED WARRANTY UNDER THE
UNIFORM COMPUTER INFORMATION TRANSACTIONS ACT OR
SIMILAR LAW AS ENACTED BY ANY STATE.
(USA only) SOME STATES DO NOT ALLOW THE EXCLUSION OF
IMPLIED WARRANTIES, SO THE ABOVE EXCLUSION MAY NOT
APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL
RIGHTS AND YOU MAY ALSO HAVE OTHER LEGAL RIGHTS THAT
VARY FROM STATE TO STATE.
MANUFACTURER MAKES NO REPRESENTATION, WARRANTY,
COVENANT OR PROMISE THAT ITS ALARM PRODUCTS AND/OR
RELATED SOFTWARE (I) WILL NOT BE HACKED, COMPROMISED
AND/OR CIRCUMVENTED; (II) WILL PREVENT, OR PROVIDE
ADEQUATE WARNING OR PROTECTION FROM, BREAK-INS,
BURGLARY, ROBBERY, FIRE; OR (III) WILL WORK PROPERLY IN
ALL ENVIRONMENTS AND APPLICATIONS.
Slide the batteries out from under
the circuit board and insert new
batteries observing polarity