USER MANUAL TVV6204LUS 4 CHANNELS DIGITAL VIDEO RECORDER
INSTRUCTION MANUAL To obtain the best performance and ensure device function correctly, please read this instruction manual carefully and completely. FCC Compliance USER-INSTALLER CAUTION: YOUR AUTHORITY TO OPERATE THIS FCC VERIFIED EQUIPMENT COULD BE VOIDED IF YOU MAKE CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE TO PART 15 OF THE FCC RULES.
TABLE OF CONTENTS 1 2 3 4 5 6 INTRODUCTION .......................................................................................................................4 1.1 FEATURE.......................................................................................................................4 1.2 SPECIFICATION...........................................................................................................4 HARDWARE OVERVIEW ..................................................................
1 INTRODUCTION 1.1 FEATURE z MPEG-4 Video Compression. z Resolution: Live 720×480 ( NTSC )/ 720×576 ( PAL ) Recording 720x240 ( NTSC )/ 720x288 ( PAL ) z Audio Backup / Audio Streaming. z Internal SATA Hard Disk Support. z Graphic User Interface ( GUI ). z Mouse/ IR Remote Controller Support. z USB Back Up/ Firmware Update z Compact Size, Easy Space Arrangement z Support Smart Phone and PDA. 1.
Control Interface Mouse (Optional)/DVR Control Panel /Keypad (Optional) Graphic User Interface (GUI) Yes IR Remote Controller Yes (Optional) On Screen Display & Setup Time / Date / Setup Menu Ethernet Yes DDNS Yes E-mail & FTP Yes Network IP Static/ Dynamic/ PPPoE Password Control Two levels, one for system and the other for HDD format Event List Max. 3000 records/H.D.
2 HARDWARE OVERVIEW 2.1 FRONT PANEL DVR OPERATION N ITEM 1 POWER 2 REC Recording status LED. 3 PLAY Playback status LED. 4 H.D.D H.D.D. LED. 5 O 6 DVR Function Power status LED. IR Sensor for remote control. USB connector. 7 ▲ Move upward or increase the number. 8 ▼ Move downward or decrease the number. 9 MENU Press MENU to enter or exit MENU. 1 0 ◄ Move leftward or decrease the number. 1 1 ► Move rightward or increase the number.
1 5 Pause 1 6 F.Fwd search 1 7 1 8 1 9 2 0 2 1 2 2 2 3 PLAY Pause & Field by Field Forward. Fast Forward ×2, ×8, ×16, x32, ×64. PLAY button & Get into Quick Time Search. Channel One Full Screen & Number: One. 1 Channel Two Full Screen & Number: Two. Channel Three Full Screen & Number: Three. Channel Four Full Screen & Number: Four. Quad screen: All cameras are displayed. Q d Confirmation and Backup. 2.2 BACK PANEL NO. ITEM FUNCTION 1 MOUSE Mouse interface.
10 11 12 VGA OUT D-SUB Reserved. RS-485 Reserved. ALARM IN Reserved. Relay Out Reserved. Power DC 12V /3A. 2.3 EXTERNAL ALARM(reserved) There are three types of alarms that the system can be configured, such as Motion Detection Alarm, External Alarm, and Video Loss Alarm. Motion Detection Alarm and External Alarm： When Motion Detection or External Alarm was triggered, there are 5 possible actions will be taken. a. Recording speed changed from normal to alarm recording. b.
Terminal Connectors： T+ RS-485 sends + T- RS-485 sends - R- RS-485 receives - R+ RS-485 receives + ALARM1-4 Camera alarm input. GND GND. N.C Relay N.C. COM Relay COM N.O Relay N.O. EXAMPLE 1：Connect Alarm In One with PIR (Passive Infrared). EXAMPLE 2：Connect with Alarm Siren at Relay N.O.
2.4 IR REMOTE CONTROL(Optional) ITEM REC Press REC to start recording and press twice to stop. 1-4 Select channel 1-4 with full screen. QUAD Fast backward. Picture by picture backward. Picture by picture forward. Fast Forward. Play video forward. COPY Switch channel format. ▲ Move upward or increase the number. ► Move rightward or increase the number. ▼ Move downward or decrease the number. ◄ Move leftward or decrease the number. Enter selected items. MENU Enter or Exit Main Menu.
2.5 RS-485 CONTROLLER (reserved) PIN R+ RT+ T- RS-485 DEFINE RXDA RXDB TXDZ TXDY Data Format： Data: 1 Byte / Parity: None / Start bit: 1 / Baud: 9600 Totally 3 bytes as follows: 1. Byte=0x10 ：Broadcasting DVR Byte=0x80+ID Number ：Joystick Control DVR (ID number:1~32) 2. Byte=Reference to the table as follows. ：Commands of each button. 3. Byte= the 1st Byte+ the 2nd Byte : Command for confirm checksum.
user wants to connect DVR with joystick controllers, please make sure each DVR ID Number is unique.
2.7 VGA OUTPUT(reserved) VGA Output is optional. VGA output can connect with CRT or LCD monitor by D-SUB connector and the user can switch different resolutions and frequencies as follows. Resolution XGA Frequency 1024×768 60Hz 2.8 NETWORK When the DVR is turned on, it will detect the network connection automatically. If without network connection, the network function will be disabled. Thus, please make sure the network connection before turning on the DVR.
3 SYSTEM SETUP 3.1 MENU SETUP INTERFACE(GUI) A. CAMERA SET E. HARD DISK SETUP B. MOTION SETUP F. NETWORK SETUP C. RECORD SETUP G.
D. ALARM SETUP H.
3.2 LIVE VIEWING AND POP-UP MENU NOTE：The pop-up menu can be activated by moving the mouse cursor to the bottom of the live viewing screen. A. GUI MENU BAR With live viewing mode, press this button to get into the GUI menu. B. DISK INFORMATION With live viewing mode, press this button to display disk information. C. Record Backup With live viewing mode, press this button to backup record. D. DIGITAL ZOOM Right-click the mouse to zoom in or zoom out the image.
Press this button to turn the audio on or off。 G. DISPLAY CONTROL Within live-viewing or playback mode, use display control to switch the camera channel. H. RECORD AND PLAYBACK CONTROL Same as front panel controller and remote controller. Please see chapter 2.1 & 4 for more detail.
3.3 CAMERA SETUP Press ▲ or ▼ to select items. Press ◄ or ► to change values. Press SET to see more options. A. CAMERA Press ◄ or ► to switch channels. B. VIDEO ADJUST B.1 CONTRAST Press ◄ or ► to change contrast level. B.2 BRIGHTNESS Press ◄ or ► to change brightness level. B3. HUE Press ◄ or ► to change HUE level. B4. COLOR Press ◄ or ► to change color level. B5. SHAPRNESS Press ◄ or ► to change sharpness level. C. CAMERA TITLE Use mouse to select and change character.
D. DISPLAY Press ◄ or ► to change value for the corresponding camera would be displayed on the screen or not. E. AUTO SWITCH 2~99 seconds Press ◄ or ► to ON/OFF auto switch.
3.4 MOTION SETUP Press ▲ or ▼ to select items. Press ◄ or ► to change values. Press SET to see more options. A. CAMERA Press ◄ or ► to switch channels. B. MOTION DETECT Press ◄ or ► to change value for motion detect function. C. BUZZER Press ◄ or ► to change value for buzzer while motion detected. D. SENSITIVITY Press ◄ or ► to change sensitivity value from 001 (minimum) to 100 (maximum). E. AREA SETUP 1. Press SET to enter motion area setting. 2. Use mouse to select which block is needed. 3.
ATTENTION：PLEASE format the hard disk before changing the recording resolution. Different record resolution cannot be stored in the same hard disk. Failing to do so may cause data lost or hard disk damage!! B. NORMAL RECORD PPS Press ◄ or ► to switch PPS in normal recording. C. ALARM RECORD PPS Press ◄ or ► to switch PPS in alarm recording. D. ALARM RECORD DURATION Press ◄ or ► to set dwell time of alarm recording. E. QUALITY Press ◄ or ► to switch quality to LOW/ MEDIUM/ HIGH/ BEST. F.
A. EXT. ALARM MODE Select N.C for “normal close” alarm input, or select N.O for “normal open” alarm input. B. ALARM DISPLAY MODE Press ◄ or ► to change value for ALARM DISPLAY MODE with full screen. C. VIDEO LOSS DETECT Press ◄ or ► to switch VIDEO LOSS ALARM ON or OFF. D. EVENT LOG SETUP Press SET to change value for MOTION EVENT / VIDEO LOSS EVENT to ON / OFF. E. BUZZER TIME SETUP Press SET to set dwell time of BUZZER. F. RELAY TIME SETUP Press SET to set dwell time of RELAY. 3.
D-1. HDD PASSWORD PROTECT Press ◄ or ► to change value for hard disk format password protection. DC-2. HDD PASSWORD Press SET then use mouse to change password. Default password： 1111 D-3. FORMAT Press SET to get into FORMAT setup. Press YES or NO to execute. 3.8 NETWORK SETUP Press ▲ or ▼ to select items. Press ◄ or ► to change values. Press SET to see more options. A. IP MODE Press ▲ or ▼ to select items and ◄ or ► to change to STATIC IP or DHCP. B.
H. PPPoE H-1. PPPoE SETTING Press◄ or ► to ENABLE / DISABLE PPPoE. H-2. USER NAME Use mouse to setup user name for ADSL account. H-3 PASSWORD Use mouse to setup password for ADSL account. H-4 STATE Press SET to display status of PPPoE。 I. DDNS I-1.DDNS SETTING：Press◄ or ► to set DDNS ENABLE / DISABLE. I-2 PROVIDER：Press◄ or ► to select DDNS provider. I-3 USER NAME：Press SET to setup user name. I-4 PASSWORD：Press SET to setup password. I-5 UPDATE SCHEDULE： Use SET to dwell time of updating schedule.
3.9 BACKUP SETUP Due to each USB device with different USB driver ICs, their compatibilities differ, too. This system is compatible with most of USB flash memory. If there is compatible Issue, please refer to APPENDIX B. In addition, please format USB flash memory with FAT32. BEFORE BACKUP A. In live viewing mode, insert USB device into a USB port of the DVR. B. Get into playback mode by PLAY TIME SEARCH or EVENT LIST SEARCH and play back videos that are going to be as backup.
3.10 SYSTEM SETUP Press ▲ or ▼ to select items. Press ◄ or ► to change values. Press SET to see more options. A. DATE / TIME SETUP Press SET to set Date / TIME. B. SYSTEM TYPE Please update firmware to change system type. C. KEYBOARD LOCK Press ◄ or ► to switch TYPE1 / TYPE2 / OFF. OFF：UNLOCK the front panel. TYPE1：ONLY can channel switch. TYPE2: Block all function.
ONLY NETWORK and LANGUAGE will NOT return to default settings. Press YES to load the system default setting, and “LOAD DEFAULT!” will be displayed on the screen until recover finished.
4 DVR PLAYBACK Click the playback button playback video. on the pop-up menu to Move the cursor to the position of down. The control bar of playback will pop-up while playing. Backup STOP R.F. Pause PLAY F.F. Note: the pop-up menu can be activated by moving the mouse cursor to the bottom of the live viewing screen. 4.1 PLAY TIME SEARCH Click mouse to trigger play time search. Please set the start and end time to search.
4.2 EVENT LISTSEARCH Double click mouse to trigger event search. Please select the event to playback。 NOTE: Display the type of the event as follows. If the DVR got power loss, it will record the date and time of POWER rebooting. If REC. button has been pressed, it will record the date and time RECORD in the event list. When a camera signal is lost, it will record the date, time, and V.LOSS corresponding channel. When ALARM is triggered, it will record the date, time, and ALARM corresponding channel.
5 DVR & USB BACKUP PLAYBACK SYSTEM REQUIREMENT： CPU: Intel Pentium III 1G or above. MEMORY: 512 MB or above. VGA: 32MB/64MB or above. OS: Microsoft Windows XP SP2 or above. VGA RESOLUTION: 1024*768 or above. 5.1 MAIN SCREEN SETTING A. MAIN SCREEN B. Open a disk drive that is with USB Backup files (e.g. F:) or other folder that is with Backup files. Each backup file will be named as START TIME. EXAMPLE: 11201817.IN is 20th Nov., 18:17 C.
5.2 PLAYER USER INTERFACE Playback mode: File/HDD/Image Play Load backup files from backup media. Playback: Play, Pause and Forward. Convert video to AVI or BMP format. HDD Time search(ONLY HDD PLAY MODE) HDD Event List(ONLY HDD PLAY MODE) Full screen: full screen or window size.
6 NETWORK VIEWING & PLAYBACK CPU: Intel Pentium III 1G or above. Memory: 512 MB or above. VGA: 32MB/64MB or above. OS: Microsoft Windows XP SP2 or above. VGA RESOLUTION: 1024*768 or above. 6.1 IP ADDRESS SETUP ON PC SITE Install cameras inside in LAN or use network cable to connect with PC. This is for IPInstallerEng.exe to set up IP address of cameras. If OS is Windows XP SP2 or above, the following Windows Security Alert will popup. Then, please click on Unblock. Then, IPInstallerEng.
6.2 OPTIONAL MICROSOFT INTERNET EXPLORER SETUP: OPTION 1: DISABLE ACTIVEX WARNING A. IE Æ Tools Æ Internet Options Æ Security Æ Custom Level Æ Security Settings Æ Download unsigned ActiveX controls Æ Enable or Prompt (recommend). B. IE Æ Tools Æ Internet Options Æ Security Æ Custom Level Æ Security Settings Æ Initialize and script ActiveX controls not marked as safe Æ Enable or Prompt (recommend).
Above three options are all based on select as the prompt. As indicated in the dialogue box. Please select "YES." OPTION 2: ADD TO TRUSTED SITES IE Æ Tools Æ Internet Options Æ Security Æ Trusted sites Æ Sites 6.3 LOGIN A. INSTALL ACTIVEX B. START INSTALL ACTIVEX C.
After IP setup and connect to network or LAN, type IP address on IE Browser directly. The following User name & Password Login window will popup. Default user name: admin password: admin Default 6.4 LIVE VIEWING A. DVR CONFIGURATION Get into DVR network menu. B. SYSTEM TIME Live viewing mode: The current live viewing time. C.
screen. D. Snapshot. Full Screen. Click again to return. E. REC. Videos are saved as AVI file. F. G. Playback Time Search. Click button and playback window will popup. Time Search Event ` List `` ¾ EVENT LIST Select a HDD to list EVENT LIST on Master or Slave HDD. Click the left button of the mouse twice to play back the selected event. ¾ TIME SEARCH Input Date and Time and click Search to play back. 6.
A. System - System Information A-1 SYSTEM INFORMATION SERVER NAME: This name will show on the IP Installer. LANUGAGE：There are English, Traditional Chinese, and Simplified Chinese. After selecting one language, the following dialogue box will popup and ask the user to confirm. B. SYSTEM – USER MANAGEMENT User Management provides 3 levels of limits of authority: Administrator (the highest), User, and Anonymous.
Remove: Click User name on the user list if want to remove it. C. NETWORK – IP SETTING Click browse to select firmware to upgrade Click start to reboot the DVR.
D. NETWORK – IP SETTING D-1 IP ASSIGNMENT DHCP: In Dynamic Host Configuration Protocol (DHCP) mode, DHCP server will get setting done automatically. STATIC IP: Please input IP address, Subnet Mask, and Gateway based on network environment. D-2 PORT ASSIGNEMENT With IP Share (Router), the following Ports needed to be adjusted in case of conflict. E. NETWORK – PPPoE E-1 PPPoE SETTING Click on Enabled to enable ADSL dial function. Username: Username for ADSL account. Password: Password for ADSL account.
E-2 SEND MAIL AFTER DIALED Click on Enabled to enable SEND MAIL AFTER DIALED function. E-3 SUBJECT Mail subject. F. NETWORK / DDNS SETTING Click on Enabled to enable DDNS function. F-1 DYNDNS.ORG DDNS SETTING - DYNDNS.ORG / NO-IP.ORG PROVIDER: Select dyndns.org HOSTNAME: The registered hostname. USERNAME: The registered username. PASSWORD: The registered password. SCHEDULE UPDATE: A period of time to update IP address. STATE 1. Updating: Information update. 2. Idle: Stop service. 3.
4. Updating Failed, the name is already registered. 5. Updating Failed, please check your internet connection. F-2 DDNS.CAMNNDS.COM / DDNS2.YDSDVR.COM / NO-IP.ORG DDNS SETTING – DDNS.CAMDDNS.COM PROVIDER: Select ddns.camddns.com USERNAME: The registered username in DDNS.CAMDDNS.COM. SCHEDULE UPDATE: A period of time to update IP address. STATE 1. Updating: Information update. 2. Idle: Stop service. 3. DDNS registered successfully, now log by http://.ddns.camddns.com: Registered successfully. 4.
H. EVENT SETTING H-1 ROUTE Motion detection action can be set up on each channel individually in DVR. After the motion is detected, it will trigger emails or upload files to FTP. H-2 SUBJECT Mail Subject. I. EVENT SETTING/ ALARM SETTING I-1 ROUTE External alarm action can be set up on each channel individually in DVR. After the external alarm action is detected, it will trigger emails or upload files to FTP. I-2 SUBJECT Mail Subject.
J. EVENT SETTING/ MAIL & FTP J-1 MAIL & FTP SETTING Mail and FTP settings are for motion detection action and external alarm action. When both actions are detected, it will trigger emails or upload files to FTP.
APPENDIX A: RECORDING TIME LAPSE NTSC 80GB HDD PPS (Picture Per Sec.
PAL 80GB HDD PPS (Picture Per Sec.
APPENDIX B: HDD COMPATIBLE TABLE Brand Model Capacity Speed(RPM) SEAGATE ST380815AS 80G 7200 10 SEAGATE ST3160815AS 160G 7200 10 SEAGATE ST3250620AS 250G 7200 10 SEAGATE ST3400620AS 400G 7200 10 SEAGATE ST3500630AS 500G 7200 10 SEAGATE ST3750640AS 750G 7200 10 MAXTOR STM3250820AS 250G 7200 MAXTOR STM3250824AS 250G 7200 WD WD800AAJS-00PSA0 80G 7200 WD WD2500AAKS-00SBA0 250G 7200 WD WD4000YS-01MPB1 400G 7200 HITACHI HDS728080PLA380 82.
APPENDIX C: HARD DISK INSTALLATION 1. Hard drive jumpers need to be set properly in order to make DVR function correctly. 2. Remove DVR top cover by taking out screws from location shown below: ① ② ③ ④ 3. Below picture indicates a DVR without a H.D.D installed. 4. Please refer to the instruction from hard drive manufactory for correct jumper setting on (master) mode of the hard drive, mounting the hard drive over DVR base by facing SATA interface to DVR main board.
attached accessory pack as picture below: 5. Hooking up SATA cable and power cable to the hard drive as picture below. 6. Restores top cover then hook up with power and monitor a hard drive status message appearing if it’s been installed successful. Attentions： 1. Hard drive master mode must be set correctly. 2. Make sure power cable is unplugged before hard drive installation starts. 3. SATA cable and power cable must be hooking up correctly. 48 a11633RD4E04_V1.
