User's Manual

产品型号
PIR-900
林寿
说明书
设 计
印刷尺寸
工 艺
部件名称
材 料
版 本
注:
双色、单面印刷
成品尺寸
52.5X95mm
80克书写纸
折页
315X285mm
Ver: PIR-910-EN-1405-V6.0
Testing (Walk Test)
A. After installation, power on the detector. After one minute
self-testing, press the test button, walk in the scope (from
left to right or from right to left) and watch the LED
indicator to make sure the detector is working.
B. The LED indicator flashes once when body movement is
detected.
C. Adjust the detector angle accordingly to achieve the best
detection effect.
Detection Scope
2m
4m
6m 8m0m
0m
2m
110°
Top view
Side view
Specifications
Power supply
DC 3V (AA 1.5V LR6 Battery x 2 pcs)
Static current
≤ 90uA
Alarm current
≤ 9.5mA
Detection scope
8m/110°
Pet immunity
≤ 25kgs
Transmitting distance
≤ 80m (in open area)
Radio frequency
315MHz/433MHz (± 75KHz)
Housing material
ABS plastic
Operation Condition
Temperature: -10°C~55°C
Relative humidity: ≤80% (non-condensing)
Detector dimensions (L x W x H)
108 x 52 x 36.8 mm
Bracket dimensions (L x W x H)
52 x 30 x 26.5 mm
2m
Installation & Notices
Avoid mounting the detector close to windows, air
conditioner, heater, refrigerator, oven, sunshine and places
where the temperature changes fast or the air stream flows
frequently. If two detectors are installed in the same
detection scope, please adjust the location to avoid
interference and false alarm.
Ground
Top view
Side view
Fix the bracket on the wall with screws and attach the
detector to the bracket. Adjust installation height
or bracket to change the detection distance and angle.
It is recommended to mount it at the height of 2m from
the ground.
The detector is more sensitive to the cross movement
than to the vertical movement, so the performance of
detector is best when the detection direction is vertical
to the walking direction of people.
In working state, if the sensor is triggered Working mode:
twice within 3 minutes, it will enter sleeping mode
immediately to save power. After no movement within
next 3 minutes, the sensor goes back to the working mode.
Press the connect key on the Connect to alarm panel:
alarm panel, and then press the test button of the sensor
twice to send alarm signal. When one beep is heard, they
are connected. To check if they are connected successfully,
arm the system, and trigger the sensor again, if there is an
alarming, the connection is successful.
Ver : PIR-910-EN-1401-V6.0
Chuango. All rights reserved.
PCB Layout
Mode Setting
Usage
Open the case and remove the battery activation strip to
activate batteries. It will start self-testing for one minute.
PIR-910
Operation Manual
Wireless PIR
Motion Detector
Pet Immunity Indoor Use
Appearance
3
1. Detection window
2. LED indicator
3. Bracket
Infrared sensor: It detects the infrared rays released by
human body motion, please do not touch the surface
and always keep it clean.
Once the case is opened in working state, Tamper switch:
the tamper switch will be triggered and then generates
an alarm signal.
Testing mode: After self-testing, press the test button,
the sensor enters testing mode, and detects once every
10 seconds. After 3 minutes, the LED flashes twice, and
the sensor enters the working mode.
AA 1.5V LR6 AA 1.5V LR6
LED ON / OFF
Infrared sensor
Infrared sensor
Zone setting
Tamper switch
Test Button
LED Indication
Flash continuously: Under the self-testing state.
Intruder is detected. Flash once:
Self-testing is finished, enters the working mode.Flash twice:
Under voltage indication, please Flash once per 3 seconds:
change the batteries immediately. (User will get alert SMS about
the low battery if the PIR detector is connected to the GSM
alarm system.)
Features
PIR-900 is a high performance wireless P.I.R. motion detector.
It consists of digital dual-core fuzzy logic infrared control chip
and intelligent analysis which effectively identify interference
signals from body movement signals and reduce false alarm
rate. With automatic temperature compensation and anti-air
turbulence technology, it easily adapts to environmental
changes. The detector also has the advantages of energy
saving, reliability and easy installation. With low power
feedback function, user will get alert SMS about the low
battery if the PIR detector is connected to the GSM alarm
system.