OWNER’S MANUAL Chrysler LLC 81-326-0926 First Edition Printed in U.S.A.
VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name Chrysler LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefor. DRIVING AND ALCOHOL Drunken driving is one of the most frequent causes of accidents. Your driving ability can be seriously impaired with blood alcohol levels far below the legal minimum. If you are drinking, don’t drive. Ride with a designated non-drinking driver, call a cab, a friend, or use public transportation.
SECTION TABLE OF CONTENTS PAGE 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77 3 4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION 1 CONTENTS 䡵 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 Van Conversions/Campers . . . . . . . . . . . . . . . . . 6 䡵 How To Use This Manual . . . . . . . . . . . . . . . . . . 4 䡵 Vehicle Identification Number 䡵 Warnings And Cautions . . . . . . . . . . . . . . . . . . . 6 䡵 Vehicle Modifications/Alterations . . . . . . . . . . . . 7 ..............
4 INTRODUCTION INTRODUCTION This Owner’s Manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your vehicle. It is supplemented by a Warranty Information Booklet and various customer-oriented documents. You are urged to read these publications carefully. Following the instructions and recommendations in this manual will help assure safe and enjoyable operation of your vehicle.
INTRODUCTION 5 1
6 INTRODUCTION WARNINGS AND CAUTIONS This Owner’s Manual contains WARNINGS against operating procedures that could result in an accident or bodily injury. It also contains CAUTIONS against procedures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important information. Observe all Warnings and Cautions.
INTRODUCTION 7 VEHICLE IDENTIFICATION NUMBER The Vehicle Identification Number (VIN) is found on the left front corner of the instrument panel, visible through the windshield. This number also appears on the Automobile Information Disclosure Label affixed to a window on your vehicle, the vehicle registration and title. NOTE: It is illegal to remove the VIN.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS 䡵 A Word About Your Keys . . . . . . . . . . . . . . . . . 12 ▫ Customer Key Programming . . . . . . . . . . . . . 17 ▫ Ignition Key Removal . . . . . . . . . . . . . . . . . . 12 ▫ General Information . . . . . . . . . . . . . . . . . . . 18 ▫ Locking Doors With The Key . . . . . . . . . . . . . 14 䡵 Vehicle Security Alarm System — If Equipped . . 19 䡵 Steering Wheel Lock — If Equipped . . . . . . . . . 14 ▫ Rearming Of The System . . . . . . .
10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ To Lock The Doors . . . . . . . . . . . . . . . . . . . . 22 ▫ Sliding Rear Window – If Equipped . . . . . . . . 34 ▫ Using The Panic Alarm . . . . . . . . . . . . . . . . . 23 ▫ Wind Buffeting . . . . . . . . . . . . . . . . . . . . . . . 34 ▫ Programming Additional RKE Transmitters . . . 24 䡵 Occupant Restraints . . . . . . . . . . . . . . . . . . . . . 35 ▫ General Information . . . . . . . . . . . . . . . . . . . 24 ▫ Lap/Shoulder Belts . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 ▫ Driver And Right Front Passenger Supplemental Restraint System (SRS) – Airbag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 ▫ Event Data Recorder (EDR) . . . . . . . . . . . . . . 57 ▫ Child Restraint . . . . . . . . . . . . . . . . . . . . . . . 60 䡵 New Engine Break-In . . . . . . . . . . . . . . . . . . . . 72 ▫ 5.7L Gas Engine – 3500 Models Only . . . . . . . 72 䡵 Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . .
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS The authorized dealer that sold you your vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys from your authorized dealer. Ask your authorized dealer for these numbers and keep them in a safe place. Ignition Key Ignition Key Removal Automatic Transmission Place the shift lever in PARK. Turn the ignition switch to the LOCK position, and remove the key.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 NOTE: • If you try to remove the key before you place the shift lever in PARK, the key may become trapped temporarily in the ignition cylinder. If this occurs, rotate the key to the right slightly, then remove the key as described. If a malfunction occurs, the system will trap the key in the ignition cylinder to warn you that this safety feature is inoperable. The engine can be started and stopped but the key cannot be removed until you obtain service.
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Don’t leave the key in the ignition. A child could operate power windows, other controls, or move the vehicle. CAUTION! An unlocked car is an invitation to thieves. Always remove key from the ignition and lock all doors when leaving the vehicle unattended.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 To Release the Steering Wheel Lock Insert the key in the ignition switch and start the engine. If the key is difficult to turn, move the wheel slightly to the right or left to disengage the lock. NOTE: If you turned the wheel to the right to engage the lock, you must turn the wheel slightly to the right to disengage it. If you turned the wheel to the left to engage the lock, turn the wheel slightly to the left to disengage it.
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE During normal operation, after turning on the ignition switch, the Vehicle Security Light will turn on for three seconds for a bulb check. If the light remains on after the bulb check, it indicates that there is a problem with the electronics. In addition, if the Vehicle Security Light begins to flash after the bulb check, it indicates that someone used an invalid key to try to start the engine.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 CAUTION! Always remove the Sentry Keys威 from the vehicle and lock all doors when leaving the vehicle unattended. At the time of purchase, the original owner is provided with a four-digit Personal Identification Number (PIN). Keep the PIN in a secure location. This number is required for authorized dealer replacement of keys. Duplication of keys may be performed at an authorized dealer or by following the customer key programming procedure.
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Insert a blank Sentry Key威 into the ignition switch. Turn the ignition switch to the ON position within 60 seconds. After 10 seconds, a single chime will sound. In addition, the Vehicle Security Light will stop flashing. To indicate that programming is complete, the Vehicle Security Light will turn on again for three seconds and then turn off.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 VEHICLE SECURITY ALARM SYSTEM — IF EQUIPPED This Vehicle Security Alarm system monitors the vehicle doors and ignition for unauthorized operation. When the alarm is activated, the system provides both audible and visible signals. For the first three minutes the horn will sound and the headlights and security light will flash repeatedly. For an additional 15 minutes only, the headlights and security light will flash.
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Disarm the System Use the RKE transmitter to unlock the door. If something has triggered the system in your absence, the horn will sound three times when you unlock the doors and the Vehicle Security Light will flash for 30 seconds. Check the vehicle for tampering. The Vehicle Security Alarm system will also disarm if the vehicle is started with a programmed Sentry Key威.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 REMOTE KEYLESS ENTRY (RKE) — IF EQUIPPED The system allows you to lock or unlock the doors from distances up to about 23 ft (7 m) using a Remote Keyless Entry (RKE) transmitter. The RKE transmitter does not need to be pointed at the vehicle to activate the system.
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Unlock the Doors Press and release the UNLOCK button on the RKE transmitter once to unlock only the driver’s door or twice to unlock all the doors. When the UNLOCK button is pressed, the illuminated entry will initiate, the parking lights will flash on twice and, if installed, the cargo lamp will turn on for 30 seconds.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 The Horn Chirp feature is activated when shipped from the assembly plant. If desired, this feature can be disabled by using the following procedure: 1. Perform this operation while standing outside the vehicle. 2. Press and hold the LOCK button on a programmed (i.e., functional) RKE transmitter. 3. Continue to hold the LOCK button, wait at least four seconds, but no longer than 10 seconds, then press and hold the PANIC button.
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To cancel the Panic Mode, press and release the PANIC button on the transmitter a second time, after five seconds. Panic Mode will automatically cancel after three minutes, or if the vehicle is started and exceeds 15 mph (24 km/h). During the Panic Mode, the door locks and RKE systems will function normally. Panic Mode will not disarm the Vehicle Security Alarm System on vehicles so equipped. 1. This device may not cause harmful interference.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 RKE Transmitter Battery Service 1. With RKE transmitter buttons facing down, use a flat blade or dime to pry the two halves of the RKE transmitter apart. Make sure not to damage the rubber gasket during removal. 2. Remove and replace the battery. When replacing the battery, match the + sign on battery to the + sign on the inside of the battery clip, located on back cover. Avoid touching the new battery with your fingers.
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE REMOTE STARTING SYSTEM — IF EQUIPPED Your vehicle may be equipped with a remote starting system, which will allow the vehicle to be started from distances up to approximately 300 ft (91 m) away from the vehicle using the Remote Keyless Entry (RKE) transmitter, which is part of your ignition key. In order to remote start your vehicle, the hood and all the doors must be closed. running.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 The vehicle can be started remotely up to a maximum of two times. The vehicle is also allowed a maximum of one failed start, where the remote start sequence was initiated but the engine stopped cranking without starting. After either of these conditions, or if the Vehicle Security Alarm is alarming, or if the PANIC button was pressed, the vehicle must be reset by inserting a valid key into the ignition and moving it to the RUN position, then back to LOCK.
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Power Door Locks — If Equipped A power door lock switch is on each front door trim panel. Use this switch to lock or unlock the doors. locks will not operate. This prevents you from accidentally locking your keys in the vehicle. Removing the key or closing the door will allow the locks to operate. A chime will sound if the key is in the ignition switch and a door is open, as a reminder to remove the key.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 3. Place the key into the ignition. 4. Within 15 seconds, cycle the key from the LOCK position to the ON/RUN position a minimum of four times, ending in the LOCK position. (Do not start the engine.) 5. Within 30 seconds, press the driver’s door LOCK switch in the LOCK direction. 6. A single chime will be heard to indicate the feature has been disabled. 7. To reactivate this feature, repeat the above steps. 8.
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 5. Within 30 seconds, press the driver’s door LOCK switch in the UNLOCK direction. 6. A single chime will sound to indicate the feature has been changed. 7. Repeat the above steps to alternate the availability of this feature. 8. If a chime is not heard, the program mode was canceled before the feature could be changed. If necessary, repeat the above procedure.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 To use the system, open each rear door, slide the lever UP to engage the locks and DOWN to disengage the child protection door locks. When the system on a door is engaged, that door can only be opened by using the outside door handle even, if the inside door LOCK is in the UNLOCKED position. WARNING! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged.
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WINDOWS Power Windows – If Equipped and on the rear doors of Quad Cab威 models. The windows will operate when the ignition switch is turned to the ON or ACC (Accessory) position and for ten minutes after the ignition is turned OFF or a front door is opened. NOTE: The Power Accessory Delay feature will allow the power windows to operate for 10 minutes after the ignition is turned OFF.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 Auto Down (Driver’s Side Only) The driver’s window switch has an Auto Down feature. Press the window switch past the detent, release, and the window will go down automatically. 2 Window Lockout Switch (4-Door Models Only) The window lockout switch on the driver’s door allows you to disable the window control on the other doors. To disable the window controls on the other doors, press the window lockout switch.
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Power Sliding Rear Window – If Equipped Sliding Rear Window – If Equipped A locking device in the center of the window helps to prevent entry from the rear of the vehicle. Squeeze the lock to release the window. Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down or in partially open positions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 OCCUPANT RESTRAINTS Some of the most important safety features in your vehicle are the restraint systems. These include the front and rear seat belts for the driver and all passengers, and front airbags for both the driver and front passenger. If you will be carrying children too small for adult-size belts, your seat belts also can be used to hold infant and child restraint systems. Please pay close attention to the information in this section.
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE of ejection and the risk of injury caused by striking the inside of the vehicle. Everyone in a motor vehicle should be belted at all times. Lap/Shoulder Belts All seating positions except the Quad Cab威 front center seating position have combination lap/shoulder belts. The belt webbing retractor is designed to lock during very sudden stops or collisions. This feature allows the shoulder part of the belt to move freely with you under normal conditions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 WARNING! WARNING! (Continued) • Wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and can take the forces of a collision best. Wearing your belt in the wrong place could make your injuries in a collision much worse. You might suffer internal injuries, or you could even slide out of part of the belt.
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. The seat belt latch plate is above the back of the front seat, next to your arm in the rear seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to allow the belt to go around your lap. 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 WARNING! WARNING! (Continued) • A belt buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you as well. In a sudden stop you could move too far forward, increasing the possibility of injury. Wear your seat belt snugly.
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision. WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 WARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Seat belt assemblies must be replaced after a collision if they have been damaged (bent retractor, torn webbing, etc.) or if the airbag deployed. key is pressed into the buckle.
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. To reattach the seat belt to the front center seat, pull the black buckle latch plate forward from the cab back panel and insert it into the black keyed buckle until there is an audible “click”. For proper seatbelt usage, refer “Lap/ Shoulder Belt Operating Instructions” in this section.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 WARNING! In Use Position • If the black latch and black buckle are not properly connected when the seat belt is used by an occupant, the seat belt will not be able to provide proper restraint and will increase the risk of injury in a collision. • When reattaching the black latch and black buckle, ensure the seat belt webbing is not twisted.
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Adjustable Upper Shoulder Belt Anchorage In the front row outboard seats, the shoulder belt can be adjusted upward or downward to help position the belt away from your neck. Press the button located on the upper belt guide, and then move it up or down to the position that fits you best. As a guide, if you are shorter than average you will prefer a lower position, and if you are taller than average you’ll prefer a higher position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 How To Use The Automatic Locking Mode 1. Buckle the combination lap/shoulder belt. 2. Grasp the shoulder portion and pull downward until the entire belt is extracted. 3. Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode.
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Enhanced Driver Seat Belt Reminder System (BeltAlert姞) If the driver’s seat belt has not been buckled within 60 seconds of starting the vehicle and if the vehicle speed is greater than 5 mph (8 km/h), the Enhanced Warning System (BeltAlert威) will alert the driver to buckle their seat belt. The driver should also instruct all other occupants to buckle their seat belts.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 4. Turn off the engine. A single chime will sound to signify that you have successfully completed the programming. Keep the belt low so that it does not come across the abdomen. That way the strong bones of the hips will take the force if there is a collision. The Enhanced Warning System (BeltAlert威) can be reactivated by repeating this procedure.
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Driver And Right Front Passenger Supplemental Restraint System (SRS) – Airbag This vehicle may have front airbags for both the driver and front passenger (if equipped) as a supplement to the seat belt restraint systems. The driver’s front airbag is mounted in the center of the steering wheel. The passenger’s front airbag (if equipped) is mounted in the instrument panel, above the glove compartment. The words SRS AIRBAG are embossed on the airbag covers.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 WARNING! • Do not put anything on or around the airbag covers or attempt to manually open them. You may damage the airbags and you could be injured because the airbags are not there to protect you. These protective covers for the airbag cushions are designed to open only when the airbags are inflating. • Do not mount any aftermarket equipment such as trailer brake controllers, snowplow controllers, auxiliary light switches, radios, etc.
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Infants in rear-facing child restraints must NEVER ride in the front seat of a vehicle with a passenger front airbag unless the airbag is turned off (Regular Cab Vehicles Only). An airbag deployment can cause severe injury or death to infants in that position. Refer to the “Passenger Airbag On/Off Switch (if equipped)” in this section.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 Airbag System Components How The Airbag System Works The airbag system consists of the following: • The Occupant Restraint Controller (ORC) determines if a frontal collision is severe enough to require the airbags to inflate.
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • If it detects a malfunction in any part of the system, it turns on the light either momentarily or continuously. The instrument cluster will flash the seat belt indicator if it detects a fault with the airbag indicator. WARNING! Ignoring the Airbag Warning Light in your instrument panel could mean you won’t have the airbags to protect you in a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 Passenger Airbag On/Off Switch (Regular Cab Vehicles Only) – If Equipped The passenger front airbag is to be turned off only if the passenger: • is an infant (less than one year old) who must ride in the front seat because there is no rear seat, because the rear seat is too small for a rear-facing infant restraint or because the infant has a medical condition which makes it necessary for the driver to be able to see the infant, • is a child, age one to 12 who
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Whenever an airbag is turned off, even a lap/ shoulder belted passenger may hit their head, neck, or chest on the dashboard (instrument panel) or windshield in a crash. This may result in serious injury or death. To Shut Off the Passenger Airbag (Regular Cab Vehicles Only) – If Equipped Place the ignition key in the Passenger Airbag On/Off Switch (if equipped), push the key in and turn clockwise, and remove the key from the switch.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 If you do have a collision which deploys the airbags, any or all of the following may occur: • The nylon airbag material may sometimes cause abrasions and/or skin reddening to the driver and front passenger as the airbags deploy and unfold. The abrasions are similar to friction rope burns or those you might get sliding along a carpet or gymnasium floor. They are not caused by contact with chemicals. They are not permanent and normally heal quickly.
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Enhanced Accident Response System If the airbags deploy after an impact and the electrical system remains functional, vehicles equipped with power door locks will unlock automatically. In addition, approximately 10 seconds after the vehicle has stopped moving, the interior lights will light until the ignition switch is turned off.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 NOTE: Perchlorate Material – special handling may apply: Refer to www.dtsc.ca.gov/hazardouswaste/perchlorate. Airbag Warning Light You will want to have the airbags ready to inflate for your protection in an impact.
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: • A near-deployment event occurs when the airbag sensor detects severe vehicle deceleration usually indicative of a crash, but not severe enough to warrant airbag deployment. • Under certain circumstances, EDR data may not be recorded (e.g., loss of battery power).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 1. Used for research purposes, such as to match data with a particular crash record in an aggregate database, provided confidentiality of personal data is thereafter preserved • Airbag deployment level (if applicable) 2. Used in defense of litigation involving a Chrysler LLC product • Brake status (service and parking brakes) 3. Requested by police under a legal warrant • Engine control status (including engine speed) 4.
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Child Restraint Everyone in your vehicle needs to be buckled up all the time — babies and children, too. Every state in the United States and all Canadian provinces require that small children ride in proper restraint systems. This is the law, and you can be prosecuted for ignoring it. Children 12 years and under should ride properly buckled up in a rear seat, if available.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 of child restraints can be used rearward-facing: infant carriers and ⬙convertible⬙ child seats. Both types of child restraints are held in the vehicle by the lap/ shoulder belt. • The infant carrier is only used rearward-facing in the vehicle. It is recommended for children who weigh up to about 20 lbs (9 kg). ⬙Convertible⬙ child seats can be used either rearward-facing or forward-facing in the vehicle.
62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint. • A rearward-facing child restraint should only be used in a rear seat, or in the front seat if the passenger’s front airbag is Off (if equipped).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 Allow the belt to return to the retractor, pulling on the excess webbing to tighten the lap portion about the child restraint. Refer to ⬙Automatic Locking Retractors (ALR) Mode⬙ in this section. • In the rear seat, you may have trouble tightening the lap/shoulder belt on the child restraint because the buckle or latch plate is too close to the belt path opening on the restraint.
64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lower Anchors and Tether for CHildren (LATCH) Each vehicle is equipped with the child restraint anchorage system called LATCH, which stands for Lower Anchors and Tether for CHildren. LATCH child restraint anchorage systems are installed in the Regular Cab passenger seat position and the Quad Cab威 rear seat outboard positions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 Child restraint systems having attachments designed to connect to the lower anchorages are now available. Child restraints having tether straps and hooks for connection to the seat back tether anchorage have been available for some time. In fact, many child restraint manufacturers will provide add-on tether strap kits for some of their older products.
66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: When using the LATCH attaching system to install a child restraint, please ensure that all seat belts not being used for occupant restraints are stowed and out of reach of children. It is recommended that before installing the child restraint, buckle the seat belt so the seat belt is tucked behind the child restraint and out of reach.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 rearward-facing infant restraints will also be equipped with a tether strap, a hook and means for adjusting the tension in the strap. In general, you will first loosen the adjusters on the lower straps and tether straps so that you can more easily attach the hook or connector to the lower anchorages and tether anchorages. Then tighten all three straps as you push the child restraint rearward and downward into the seat.
68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! An incorrectly anchored tether strap could lead to seat failure and injury to the child. In a collision, the seat could come loose and allow the child to crash into the inside of the vehicle or other passengers, or even be thrown from the vehicle. Use only the anchor positions directly behind the child seat to secure a child restraint top tether strap. Follow the instructions below. See your authorized dealer for help if necessary.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 Multiple Child Restraint Installation Sequence (Quad Cab威 - Rear Seats) 1. Obtain tether straps by raising the head restraints and reaching between the rear glass and rear seat. The tether strap may be retained with an elastic band. Accessibility to the tether strap is greatly improved by raising the seat cushion to the “up” position. Remove the elastic before use.
70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 5. Place a child restraint on the center rear seat and adjust the tether strap so that it will reach under the head restraint to the tether anchor directly behind the seat and to the anchor directly behind the right seat. 6. Install each child restraint and remove the slack in the tether strap according to the child restraint manufacturer’s instructions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 Tether Anchorage Points at All Three Seating Positions 1. Place the child restraint on the seat and adjust the tether strap so that it will reach over the seat back under the head restraint to the tether anchor directly behind the seat. 2 2. Lift the cover, and attach the hook to the square opening in the sheet metal. 3. Install the child restraint and remove the slack in the tether strap according to the manufacturer’s instructions.
72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Children Too Large for Booster Seats Children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the seat back should use the lap/shoulder belt in a rear seat. • Make sure that the child is upright in the seat. • The lap portion should be low on the hips and as snug as possible. • Check belt fit periodically.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 occur. For recommended viscosity and quality grades, refer to “Engine Oil” under “Maintenance Procedures” in Section 7. SAFETY TIPS Exhaust System 2 NON-DETERGENT OR STRAIGHT MINERAL OILS MUST NEVER BE USED. WARNING! A new engine may consume some oil during its first few thousand miles (kilometers) of operation. This is a normal part of the break-in and is not an indication of difficulty.
74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. Be aware of changes in the sound of the exhaust system, exhaust fumes detected inside the vehicle, or damage to the underside or rear of the vehicle. Have a competent mechanic inspect the complete exhaust system and adjacent body areas for broken, damaged, deteriorated or mispositioned parts.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 Airbag Warning Light The airbag warning light should come on, and remain on, for six to eight seconds as a bulb check when the ignition switch is first turned ON. If the light is not lit during starting, see your authorized dealer. If the light stays on, flickers or comes on while driving, have the system checked by an authorized dealer. If there is a problem with the airbag warning light, the seat belt light will flash.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 䡵 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 ▫ Inside Day/Night Mirror . . . . . . . . . . . . . . . . 81 ▫ Automatic Dimming Mirror — If Equipped . . . 82 ▫ Outside Mirrors . . . . . . . . . . . . . . . . . . . . . . 82 ▫ Outside Mirrors Folding Feature . . . . . . . . . . 83 ▫ Power Mirrors — If Equipped . . . . . . . . . . . . 83 ▫ Heated Power Mirrors — If Equipped . . . . . . 84 ▫ Trailer Towing Mirrors — If Equipped . . .
78 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 䡵 Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114 ▫ 40-20-40 Front Seat . . . . . . . . . . . . . . . . . . . 115 ▫ Reclining Seats . . . . . . . . . . . . . . . . . . . . . . 116 ▫ Adjustable Head Restraints . . . . . . . . . . . . . 117 ▫ Manual Rotary Lumbar Support Adjustment — If Equipped . . . . . . . . . . . . . 118 ▫ Headlights, Parking Lights And Panel Lights . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 79 䡵 Electronic Speed Control — If Equipped . . . . . 133 ▫ Distance To Empty (DTE) . . . . . . . . . . . . . . 139 ▫ To Activate . . . . . . . . . . . . . . . . . . . . . . . . . 134 ▫ Trip Odometer (ODO) . . . . . . . . . . . . . . . . . 139 ▫ To Set At A Desired Speed . . . . . . . . . . . . . . 134 ▫ Elapsed Time (ET) . . . . . . . . . . . . . . . . . . . 140 ▫ To Deactivate . . . . . . . . . . . . . . . . . . . . . . . 134 ▫ C/T Button . . . . . . . .
80 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 䡵 Cupholders . . . . . . . . . . . . . . . . . . . . . . . . . . 146 ▫ Storage And Seats (Quad Cab威 Models) . . . . 152 ▫ Front Instrument Panel Cupholders (40–20–40 Seats) . . . . . . . . . . . . . . . . . . . . . 146 ▫ Plastic Grocery Bag Retainers . . . . . . . . . . . . 153 ▫ Front Instrument Panel Cupholders (Bucket Seats) . . . . . . . . . . . . . . . . . . . . . . . 147 ▫ Rear Cupholder (Quad Cab威) — If Equipped . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 81 MIRRORS Inside Day/Night Mirror Headlight glare can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle). The mirror should be adjusted while set in the day position (toward the windshield). The mirror should be adjusted to center on the view through the rear window.
82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Dimming Mirror — If Equipped This mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light in the button will illuminate to indicate when the dimming feature is activated. CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83 WARNING! Vehicles and other objects seen in a right side convex mirror will look smaller and farther away than they really are. Relying too much on your right side convex mirror could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in the right side convex mirror. Some vehicles will not have a convex right side mirror.
84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Set the top switch to the left or right for the left or right mirror, and set it to the center off position to prevent accidentally moving a mirror when you are finished adjusting the mirror. To adjust a mirror, select left or right with the top switch, and press one of the four arrows for the direction you want the mirror to move.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85 A small blindspot mirror is integrated onto the main mirror surface. 3 Trailer Towing Position NOTE: Fold the trailer towing mirrors rearward prior to entering an automated car wash.
86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE HANDS-FREE COMMUNICATION (UConnect姞) — IF EQUIPPED NOTE: The sales code RER and REU radios contain an integrated Hands-Free Communication (UConnect威) system. Refer to your “Navigation User’s Manual” for UConnect威 system operating instructions for these radios. Radio sales code can be located on the lower right corner of the Radio faceplate. UConnect威 is a voice-activated, hands-free, in-vehicle communications system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 The UConnect威 system is driven through your Bluetooth威 “Hands-Free Profile” cellular phone. UConnect威 features Bluetooth威 technology - the global standard that enables different electronic devices to connect to each other without wires or a docking station, so UConnect威 works no matter where you stow your cellular phone (be it your purse, pocket, or briefcase), as long as your phone is turned on and has been paired to the vehicle’s UConnect威 system.
88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The UConnect威 system is fully integrated with the vehicle’s audio system. The volume of the UConnect威 system can be adjusted either from the radio volume control knob or from the steering wheel radio control (right switch), if so equipped. The radio display will be used for visual prompts from the UConnect威 system such as ⬙CELL⬙ or caller ID on certain radios.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 Help Command If you need assistance at any prompt, or if you want to know your options at any prompt, say ⬙Help⬙ following the beep. The UConnect威 system will play all the options at any prompt if you ask for help. To activate the UConnect威 system from idle, simply press the PHONE button and follow the audible prompts for directions. All UConnect威 system sessions begin with a press of the PHONE button on the radio control head.
90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • For identification purposes, you will be prompted to give the UConnect威 system a name for your cellular phone. Each cellular phone that is paired should be given a unique phone name. • You will then be asked to give your cellular phone a priority level between one and seven, with one being the highest priority. You can pair up to seven cellular phones to your UConnect威 system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91 • The system will prompt you to say the name of the person you want to call. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Phonebook New Entry.⬙ • After the ⬙Ready⬙ prompt and the following beep, say the name of the person you want to call. For example, you can say ⬙John Doe,⬙ where John Doe is a previously stored name entry in the UConnect威 phonebook or downloaded phonebook.
92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The UConnect威 system will allow you to enter up to 32 names in the phonebook with each name having up to four associated phone numbers and designations. Each language has a separate 32-name phonebook accessible only in that language. In addition, if equipped and supported by your phone, UConnect威 automatically downloads your mobile phone’s phonebook.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 • This downloaded phonebook cannot be edited or deleted on the UConnect威. These can only be edited on the mobile phone. The changes are transferred and updated to UConnect威 on the next phone connection. Phonebook Download — Single Entry If equipped and supported by your phone, UConnect威 allows the user to download entries from their phone via Bluetooth威. To use this feature, press the PHONE button and say “Phonebook Download.
94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Press the PHONE button to begin. and a home number, but you can add ”John Doe’s” work number later using the ⬙Phonebook Edit⬙ feature. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Phonebook Edit.⬙ Delete UConnect威 Phonebook Entry • You will then be asked for the name of the phonebook entry that you wish to edit. NOTE: Editing phonebook entries is recommended when the vehicle is not in motion.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 • After you enter the name, the UConnect威 system will ask you which designation you wish to delete: home, work, mobile, pager, or all. Say the designation you wish to delete. • Note that only the phonebook entry in the current language is deleted. • Automatic downloaded phonebook entries cannot be deleted or edited. Delete/Erase “All” UConnect威 Phonebook Entries • Press the PHONE button to begin.
96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The user can also exercise ⬙Edit⬙ or ⬙Delete⬙ operations at this point. • The UConnect威 system will then prompt you as to the number designation you wish to call. • The selected number will be dialed. Phone Call Features The following features can be accessed through the UConnect威 system if the feature(s) are available on your cellular service plan.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 NOTE: The UConnect威 system compatible phones in the market today do not support rejecting an incoming call when another call is in progress. Therefore, the user can only answer an incoming call or ignore it. Making a Second Call While Current Call is in Progress To make a second call while you are currently on a call, press the VOICE RECOGNITION button and say ⬙Dial⬙ or ⬙Call⬙ followed by the phone number or phonebook entry you wish to call.
98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Three-Way Calling To initiate three-way calling, press the VOICE RECOGNITION button while a call is in progress, and make a second phone call, as described under ⬙Making a Second Call While Current Call is in Progress.⬙ After the second call has established, press and hold the PHONE button until you hear a double beep, indicating that the two calls have been joined into one conference call.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99 • After the ignition key is switched to OFF, a call can continue on the UConnect威 system for a certain duration, after which the call is automatically transferred from the UConnect威 system to the mobile phone. • An active call is automatically transferred to the mobile phone after the ignition key is switched to OFF. UConnect姞 System Features Language Selection To change the language that the UConnect威 system is using: • Press the PHONE button to begin.
100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After the ⬙Ready⬙ prompt and the following beep, say ⬙Emergency⬙ and the UConnect威 system will instruct the paired cellular phone to call the emergency number. This feature is supported in the U.S., Canada, and Mexico. NOTE: • The emergency number dialed is based on the country where the vehicle is purchased (911 for the U.S. and Canada and 060 for Mexico). The number dialed may not be applicable with the available cellular service and area.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 NOTE: • The towing assistance number dialed is based on the country where the vehicle is purchased (1-800-5282069 for the U.S., 1-877-213-4525 for Canada, 55-143454 for Mexico City and 1-800-712-3040 for outside Mexico City in Mexico). • If supported, this number may be programmable on some systems. To do this, press the PHONE button and say “Setup”’, followed by “Towing Assistance”. Paging To learn how to page, refer to ⬙Working with Automated Systems.
102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE or sequence of numbers, followed by ⬙Send,⬙ is also to be used for navigating through an automated customer service center menu structure, and to leave a number on a pager. You can also send stored UConnect威 phonebook entries as tones for fast and easy access to voice mail and pager entries. To use this feature, dial the number you wish to call and then press the VOICE RECOGNITION button and say, “Send.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 • After the ⬙Ready⬙ prompt and the following beep, say ⬙Setup Confirmations.⬙ The UConnect威 system will play the current confirmation prompt status and you will be given the choice to change it.
104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Following the beep, say ⬙Mute off.⬙ If you would like to connect or disconnect the Bluetooth威 connection between a UConnect威 paired cellular phone and the UConnect威 system, follow the instructions described in your cellular phone User’s Manual.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 Select Another Cellular Phone This feature allows you to select and start using another phone paired with the UConnect威 system. • Press the PHONE button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Setup Select Phone⬙ and follow the prompts. • You can also press the VOICE RECOGNITION button at any time while the list is being played, and then choose the phone that you wish to select.
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Training For users experiencing difficulty with the system recognizing their voice commands or numbers, the UConnect威 system Voice Training feature may be used. To enter this training mode, follow one of the two following procedures: From outside the UConnect威 mode (e.g.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 • low-to-medium blower setting, • low-to-medium vehicle speed, • low road noise, • smooth road surface, • fully closed windows, • dry weather condition. • Even though the system is designed for users speaking in North American English, French, and Spanish accents, the system may not always work for some. • When navigating through an automated system such as voice mail, or when sending a page, at the end of speaking the digit string, make sure to say ⬙Send.
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • low-to-medium vehicle speed, • low road noise, • smooth road surface, • fully closed windows, • dry weather conditions, and • operation from the driver’s seat. • Performance, such as audio clarity, echo, and loudness to a large degree rely on the phone and network, and not the UConnect威 system. • Echo at the far end can sometimes be reduced by lowering the in-vehicle audio volume.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 3
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 3
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Primary zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location all Voice Commands Alternate(s) Voice Commands Primary Alternate(s) call cancel confirmation prompts continue delete dial download edit emergency English erase all Espanol Francais help home
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 Primary language list names list phones mobile mute mute off new entry no pager pair a phone phone pairing phonebook previous record again redial Voice Commands Alternate(s) pairing phone book Voice Commands Primary Alternate(s) return to main menu return or main menu select phone select send set up phone settings or phone set up towing assistance transfer call UConnect威 Tutorial try again voice training work yes 3
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE General Information This device complies with Part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 40-20-40 Front Seat The outboard seat portions are each 40% of the total width of the seat. The back of the center portion (20%) easily folds down to provide an armrest/center storage compartment (if equipped). 3 Each outboard seat is independently adjustable forward or rearward and is equipped with a back recliner. The manual forward or rearward seat adjustment handle is found at the front edge of each seat cushion.
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust any seat only while the vehicle is parked. Reclining Seats The recliner handle is on the outside of the seat cushion. Pull up on the handle, as shown, to release the seatback and adjust for comfort.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 WARNING! You can be seriously, even fatally, injured riding in a seat with the seatback reclined. Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. If you ride in this position, the shoulder harness will no longer be restraining you. In a collision you could slide under the seat belt and receive serious or fatal injuries. Recline in a seat only when the vehicle is parked.
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Manual Rotary Lumbar Support Adjustment — If Equipped Rotating the lumbar control knob on the left side of the driver’s seatback and on the right side of the passenger’s seatback increases or decreases the lumbar (lower back) support. Power Seats — If Equipped The power seat controls are on the outboard side of the front seat cushions. Three switches control the seat movement.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 CAUTION! Do not put anything under a power seat. It may cause damage to the seat or seat controls. 3 The four-way switch in the center can be moved forward or backward to get the most comfortable position. The same switch can be moved up and down to control seat height.
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Change the seat angle by using the two toggle switches, tilting it up or down. Heated Seat Switches Tilt Adjustment Heated Seats — If Equipped The heated seat switches are located in the instrument panel under the climate controls. Press the switch once for High heat. Press the switch a second time for Low heat. Pressing the switch a third time will turn the heated seats Off.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 Low is selected just the lower light will illuminate. Flashing indicator lights on the switch indicate that the heated seat system needs servicing. See your authorized dealer. WARNING! TO OPEN AND CLOSE THE HOOD To open the hood, two latches must be released. 1. Pull the hood release lever located below the steering wheel at the base of the instrument panel.
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Reach into the opening beneath the center of the grille and push upward on the safety latch to release it before raising the hood. CAUTION! To prevent possible damage, do not slam the hood to close it. Use a firm downward push at the front center of the hood to ensure that both latches engage. WARNING! If the hood is not fully latched, it could fly up when the vehicle is moving and block your forward vision.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 LIGHTS The headlight switch is located on the left side of the instrument panel next to the steering wheel. Headlight Switch Location Interior Lights Courtesy and dome lights are turned on when the front doors are opened, when the dimmer control (rotating wheel on the right side of the switch) is rotated to the upward detent position, or if equipped, when the UNLOCK button is pressed on the Remote Keyless Entry (RKE) transmitter.
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If the ignition is OFF and any door is left ajar for 10 minutes or the dimmer control is rotated upwards for 10 minutes, the interior lights will automatically turn off. If the headlights remain on while the ignition is cycled OFF, the exterior lights will automatically turn off after eight minutes. NOTE: Battery saver mode is cancelled if the ignition is ON.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 The headlight delay time is programmable on vehicles equipped with the Electronic Vehicle Information Center (EVIC). For details, refer to “Personal Settings (Customer-Programmable Features)” under “Overhead Console with Electronic Vehicle Information Center (EVIC) – If Equipped” in Section 3.
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. To remove road dirt, wash with a mild soap solution followed by rinsing. Lights-on Reminder If the headlights, parking lights, or cargo lights are left on after the ignition is turned OFF, a chime will sound when the driver’s door is opened.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 Turn Signals Move the lever up or down to signal a right-hand or left-hand turn. The arrow on either side of the instrument cluster flashes to indicate the direction of the turn, and proper operation of the front and rear turn signal lights. If a defective bulb or wiring circuit is detected for the turn signal system, the arrow indicators will flash at a faster rate.
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Flash-to-Pass You can signal another vehicle with your headlights by partially pulling the multifunction lever toward the steering wheel. This will cause the High beam headlights to turn on until the lever is released. High Beam/Low Beam Select Switch Pull the multifunction lever fully toward the steering wheel to switch the headlights from High or Low beam.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 WINDSHIELD WIPERS AND WASHERS The wipers and washers are operated by a switch in the multifunction lever. Turn the end of the handle to select the desired wiper speed. Intermittent Wiper System The intermittent feature of this system was designed for use when weather conditions make a single wiping cycle, with a variable pause between cycles, desirable. For maximum delay between cycles, rotate the control knob into the upper end of the delay range.
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Sudden loss of visibility through the windshield could lead to an accident. You might not see other vehicles or other obstacles. To avoid sudden icing of the windshield during freezing weather, warm the windshield with the defroster before and during windshield washer use. Windshield Washers To use the washer, push in on the washer knob on the end of the multifunction lever and hold while spray is desired.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 WARNING! Tilting the steering column while the vehicle is moving is dangerous. Without a stable steering column, you could lose control of the vehicle and have an accident. Adjust the column only while the vehicle is stopped. Be sure it is locked before driving. DRIVER ADJUSTABLE PEDALS — IF EQUIPPED The power adjustable accelerator and brake pedals allow the driver to establish a comfortable position relative to the steering wheel and pedals.
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Adjustment 1. Position the driver seat so that you are at least 10 in (254 mm) away from the airbag located in the center of the steering wheel. 2. Fasten and adjust the seatbelts. 3. Move the adjustable pedal switch, located to the left of the steering column near the parking brake release, in the direction you desire to move the pedals. 4. The pedals cannot be adjusted when the vehicle is in REVERSE or when the Electronic Speed Control is set.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 ELECTRONIC SPEED CONTROL — IF EQUIPPED When engaged, Electronic Speed Control takes over accelerator operation at speeds greater than 25 mph (40 km/h). The controls are mounted on the steering wheel.
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The Electronic Speed Control system has been designed to shut down if multiple speed control switch buttons (i.e., SET and CANCEL) are operated simultaneously, in order to ensure proper operation. The system can be reactivated by pushing the Electronic Speed Control switch ON/OFF button and reestablishing the desired vehicle SET speed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 To Resume Speed To resume a previously set speed, push and release the RESUME button. Resume can be used at any speed above 30 mph (50 km/h). To Vary The Speed Setting When the Electronic Speed Control is on, speed can be increased by pressing and holding the RESUME/ACCEL button. When the button is released, a new set speed will be established. Tapping the ACCEL button once will result in a speed increase of 1 mph (2 km/h).
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Electronic Speed Control can be dangerous where the system cannot maintain a constant speed. Your vehicle could go too fast for the conditions, and you could lose control. An accident could be the result. Do not use Electronic Speed Control in heavy traffic or on roads that are winding, icy, snow-covered, or slippery.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 US/M Button Use this button to change the display from U.S. to metric measurement units.
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Step Button Use this button to choose or cycle through the four trip conditions. Average Fuel Economy (AVG ECO) Shows the average fuel economy since the last reset. Average fuel economy is a running average of the amount of fuel used and the distance the vehicle has traveled. When the fuel economy is reset, the display will momentarily blank. Then the history will be erased and the AVERAGING WILL CONTINUE FROM WHERE IT WAS BEFORE THE RESET.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 Distance To Empty (DTE) Shows the estimated distance that can be traveled with the fuel remaining in the tank. This estimated distance is determined by weighted average of the instantaneous and average fuel economy, according to the current fuel tank level. This is not resettable. NOTE: It is possible for DTE to display “LO FUEL” before the low fuel warning light turns on in the instrument cluster.
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE This display shows the distance traveled since the last reset. Resetting of this screen will cause the trip odometer to change to zero. Elapsed Time (ET) This display shows the accumulated ignition ON time since the last reset. Resetting the elapsed time will cause the display to change to zero. C/T Button Use this button to select a readout of the outside temperature and one of eight compass headings that indicate the direction in which the vehicle is facing.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 WARNING! Even if the display still reads a few degrees above 32°F (0°C), the road surface may be icy, particularly in woods or on bridges. Drive carefully under such conditions to prevent an accident and possible personal injury or property damage. 3 Global Reset If the RESET button is pressed twice within two seconds while in any of the three resettable displays (AVG, ECO, ODO, ET), the Global Reset will reset all three displays.
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE After completing up to three 360 degree turns, with the vehicle traveling less than 5 mph (8 km/h), in an area free from large metal or metallic objects, the CAL symbol will turn off and the compass will function normally. Manual Compass Calibration CAL (compass calibration) modes. When the CAL symbol is displayed, slowly drive the vehicle 5 mph (8 km/h) in a complete 360° circle in an area free from large metal objects or power lines.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 Compass Variance is the difference between magnetic North and geographic North. In some areas of the country, the difference between magnetic and geographic North is great enough to cause the compass to give false readings. If this occurs, the compass variance must be set according to the Compass Variance Map. NOTE: The default for the compass variance is Zone 8. To set the variance: Turn the ignition ON and set the display to “Compass/Temperature.
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ELECTRICAL POWER OUTLETS The auxiliary electrical outlet can provide power for in-cab accessories designed for use with the standard “cigar lighter” plug. The outlet is located in the instrument panel below and to the right of the climate control panel. A cap is attached to the outlet base indicating “Power Outlet” 12-Volt/20 A. There is an additional power outlet inside the center console of vehicles equipped with 40-20-40, or bucket front seats.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting. • Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.), will discharge the battery even more quickly.
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE cupholder door handle, on the front surface. Each opening in the cupholder is adjustable and will hold cups and mugs of various sizes. To secure the cup, place the cup to be held into one of the cup wells and then push the cupholder arm toward the cup until it is held stable. Ash Receiver CUPHOLDERS Front Instrument Panel Cupholders (40–20–40 Seats) Your new vehicle is equipped with two adjustable cupholders.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 3 Cupholders Cupholders Bucket Seat Front Instrument Panel Cupholders (Bucket Seats) If your new vehicle is equipped with bucket seats there are three cupholders located on the front of the center console. Rear Cupholder (Quad Cab姞) — If Equipped Quad Cab威 vehicles may be equipped with a rear cupholder that consists of two cupwells for rear passenger convenience.
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE STORAGE Center Storage Compartment (40–20–40 Seat) — If Equipped The center portion of the seat folds down to provide an armrest with unique storage compartments under the lid. Push the button on the front of the armrest to raise the cover. Inside there is a power outlet (if equipped), removable coin holder (if equipped), and two dividers to configure the storage area into compartments.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 WARNING! CAUTION! • This armrest is not a seat. Anyone seated on the armrest could be seriously injured during vehicle operation, or an accident. Only use the center seating position when the armrest is fully upright. • In an accident, the latch may open if the total weight of the items stored exceeds about 10 lbs (4.5 kg). These items could be thrown about endangering occupants of the vehicle. Items stored should not exceed a total of 10 lbs (4.5 kg).
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Center Storage Compartment (Bucket Seats) — If Equipped Push the upper button on the front of the armrest to raise the upper cover. Inside is a power outlet (if equipped), a cut out for a cell phone charger cord, removable coin holder (if equipped), and a divider to configure the storage area into separate compartments. Lift the lower handle on the front of the armrest, and raise the armrest for access to the lower storage bin.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 WARNING! CAUTION! • This armrest is not a seat. Anyone seated on the armrest could be seriously injured during vehicle operation, or an accident. Only use the center seating position when the armrest is fully upright. • In an accident, the latch may open if the total weight of the items stored exceeds about 10 lbs (4.5 kg). These items could be thrown about endangering occupants of the vehicle. Items stored should not exceed a total of 10 lbs (4.5 kg).
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Storage and Seats (Quad Cab姞 Models) Located in the center of the front 40–20–40 seat cushion there is a storage compartment. Regular Cab models also have storage behind the seat. The Quad Cab威 models provide additional storage under the rear seat. Lift the seat to access the storage compartment.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 Plastic Grocery Bag Retainers Retainer hooks which will hold plastic grocery bag handles are built into the back panel of the cab, behind the rear seat. Grocery Bag Hooks REAR WINDOW FEATURES Rear Window Defroster and Heated Sideview Mirrors — If Equipped The electric rear window defroster and heated sideview mirrors are activated by pressing the heated grid button, located on the climate control panel, with the ignition ON.
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Sliding Rear Window — If Equipped The power sliding rear window switch is located on the instrument panel below the climate controls. Press the right side of the switch to open the glass and the left side of the switch to close the glass. Sliding Rear Window — If Equipped A locking device in the center of the window helps to prevent entry from the rear of the vehicle. Squeeze the lock to release the window.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 Unfolding the Load Floor 1. Lift the 60/40 seat cushion(s) to the upward position. 2. Grasp the knob on the load floor and lift the knob until the load floor unfolds into position. 3 Unfolding The Load Floor Load Floor In Open Position 3. Reverse the procedure to store the load floor.
156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Positioning the Load Floor for Storage Access Under the Seat 1. Lift the 60/40 seat cushion(s) to the upward position. 2. Unsnap the securing snap located at either side of the load floor. 3. Lift the load floor up to access storage under the load floor. WARNING! Do not drive with the load floor in the up position. When stopping fast or in an accident, the load floor could move to the down position causing serious injury. Load Floor Securing Straps 4.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 Instrument Panel Features . . . . . . . . . . . . . . . 160 䡵 Instrument Cluster . . . . . . . . . . . . . . . . . . . . 161 䡵 Instrument Cluster Description . . . . . . . . . . . . 162 䡵 Electronic Digital Clock . . . . . . . . . . . . . . . . . 172 ▫ Clock Setting Procedure . . . . . . . . . . . . . . . 172 䡵 Sales Code RAQ – AM/FM/CD (6-Disc) Radio With Optional Satellite Radio, Hands Free Phone, And Video Entertainment Systems (VES)™ Capabilities . . . .
158 UNDERSTANDING YOUR INSTRUMENT PANEL 䡵 Sales Code REF — AM/FM/CD (Single-Disc) Radio With Optional Satellite Radio And Hands-Free Phone Capability . . . . . . . . . . . . . . 187 ▫ Operating Instructions - Radio Mode . . . . . . 187 ▫ Operating Instructions - CD Mode . . . . . . . . 191 ▫ Operating Instructions - Auxiliary Mode . . . . 192 ▫ Operating Instructions - Hands-Free Phone — If Equipped . . . . . . . . . . . . . . . . . . . . . . 194 ▫ Operating Instructions - Satellite Radio — If Equipped . .
UNDERSTANDING YOUR INSTRUMENT PANEL 159 䡵 Video Entertainment System™ (Sales Code XRV) — If Equipped . . . . . . . . . . . . . . . . . . . . 201 䡵 Remote Sound System Controls — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 201 ▫ Radio Operation . . . . . . . . . . . . . . . . . . . . . 202 䡵 Climate Controls . . . . . . . . . . . . . . . . . . . . . . 204 ▫ Heater Only — If Equipped . . . . . . . . . . . . . 204 ▫ Air Conditioning And Heating — If Equipped . . . . . . . . . . . . . . .
160 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT PANEL FEATURES 1 - Headlight Switch 2 - Air Outlets 6 - Passenger Airbag 7 - Glove Compartment 3 - Instrument Cluster 8 - Passenger Airbag On/Off Switch* 9 - Power Outlet 10 - Heated Seat Switch 4 - Climate Controls 5 - Radio 11 - Exhaust Brake Switch* 12 - Power Sliding Back Glass Switch* 13 - Cupholders 14 - Cigar Lighter 15 - Transfer Case Control Switch* 16 - Parking Brake Release Lever 17 - Adjustable Pedal Control Switch* * If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 161 INSTRUMENT CLUSTER 4
162 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTION 1. Check Gauges This light illuminates when the Voltmeter, Engine Oil Pressure or Engine Coolant Temperature gauges indicate a reading either too high or too low. Examine the gauges carefully, and follow the instructions contained below for each indicated problem. NOTE: When the ignition switch is turned to OFF, the Fuel Gauge, Voltmeter, Oil Pressure and Engine Coolant Temperature gauges may not show accurate readings.
UNDERSTANDING YOUR INSTRUMENT PANEL 163 4. Tachometer The tachometer indicates engine speed in revolutions per minute. CAUTION! Do not operate the engine with the tachometer pointer at high rpm for extended periods. Engine damage may occur. 5. Airbag Warning Light The indicator lights and remains lit for six to eight seconds when the ignition is first turned on. If the light stays on, flickers or comes on while driving, have the airbag system checked by an authorized dealer. 6.
164 UNDERSTANDING YOUR INSTRUMENT PANEL 9. Oil Pressure Gauge The pointer should always indicate some oil pressure when the engine is running. A continuous high or low reading, under normal driving conditions, may indicate a lubrication system malfunction. Immediate service should be obtained. NOTE: If the gauge pointer moves to either extreme of the gauge, the “Check Gauges” indicator will illuminate and a single chime will sound. 10.
UNDERSTANDING YOUR INSTRUMENT PANEL 165 The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer. It should not be allowed to exceed the upper limits of the normal operating range. CAUTION! Driving with a hot engine cooling system could damage your vehicle. If temperature gauge reads “H” pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.
166 UNDERSTANDING YOUR INSTRUMENT PANEL 15. Shift Lever Indicator (Automatic Transmission Only) This display indicator shows the automatic transmission shift lever selection. NOTE: You must apply the brake before shifting from PARK. 16. Odometer/Trip Odometer The odometer shows the total distance the vehicle has been driven. U.S. federal regulations require that upon transfer of vehicle ownership, the seller certify to the purchaser the correct mileage that the vehicle has been driven.
UNDERSTANDING YOUR INSTRUMENT PANEL 167 button down for a period of six seconds. The odometer will change to trip value first, then it will display the engine hour value. The engine hours will be displayed for a period of 30 seconds until the ignition is turned off or the engine is started. Change Oil Message Your vehicle is equipped with an engine oil change indicator system.
168 UNDERSTANDING YOUR INSTRUMENT PANEL 18. Malfunction Indicator Light (MIL) The Malfunction Indicator Light (MIL) is part of an onboard diagnostic system which monitors the emissions and engine control system. If the vehicle is ready for emissions testing the light will come on when the ignition is first turned on and remain on, as a bulb check, until the engine is started.
UNDERSTANDING YOUR INSTRUMENT PANEL 169 If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder reservoir, it indicates a possible brake hydraulic system malfunction or a problem with the Brake Booster has been detected by the Anti-Lock Brake System (ABS) / Electronic Stability Program (ESP) system. In this case, the light will remain on until the condition has been corrected.
170 UNDERSTANDING YOUR INSTRUMENT PANEL Operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON position. The light should illuminate for approximately two seconds. The light should then turn off unless the parking brake is applied or a brake fault is detected. If the light does not illuminate, have the light inspected by an authorized dealer. The light also will turn on when the parking brake is applied with the ignition switch in the ON position.
UNDERSTANDING YOUR INSTRUMENT PANEL 171 engine is running, immediate service is required and you may experience reduced performance, an elevated/ rough idle or engine stall and your vehicle may require towing. The light will come on when the ignition is first turned on and remain on for 15 seconds as a bulb check. If the light does not come on during starting, have the system checked by an authorized dealer. 22.
172 UNDERSTANDING YOUR INSTRUMENT PANEL 26. Low Fuel Light This light illuminates when the pointer is between “E” and 1/8 indication mark (approximately 15% of tank volume) on the fuel gauge. When the fuel gauge pointer is on “E” (equivalent to Distance To Empty [DTE] = 0 on the overhead console, if so equipped) there is reserve fuel capacity, which corresponds to approximately 8% of tank volume.
UNDERSTANDING YOUR INSTRUMENT PANEL 173 3. After the hours are adjusted, press the right side Tune/Audio control to set the minutes. 4. Adjust the minutes using the right side Tune/Audio control. 5. To exit, press any button/knob or wait approximately five seconds. SALES CODE RAQ – AM/FM/CD (6-DISC) RADIO WITH OPTIONAL SATELLITE RADIO, HANDS FREE PHONE, AND VIDEO ENTERTAINMENT SYSTEMS (VES)™ CAPABILITIES NOTE: The radio sales code is located on the lower right side of your radio faceplate.
174 UNDERSTANDING YOUR INSTRUMENT PANEL Power Switch/Volume Control (Rotary) Press the ON/VOL control to turn the radio ON. Press the ON/VOL a second time to turn OFF the radio. Electronic Volume Control The electronic volume control turns continuously (360 degrees) in either direction without stopping. Turning the volume control to the right increases the volume and to the left decreases it. When the audio system is turned on, the sound will be set at the same volume level as last played.
UNDERSTANDING YOUR INSTRUMENT PANEL 175 SCAN Button (Radio Mode) Pressing the SCAN button causes the tuner to search for the next listenable station, in either AM, FM or Satellite (if equipped) frequencies, pausing for 5 seconds at each listenable station before continuing to the next. To stop the search, press SCAN a second time. MSG or INFO Button (Radio Mode) Press the MSG or INFO button for an RBDS station (one with call letters displayed).
176 UNDERSTANDING YOUR INSTRUMENT PANEL AM/FM Button (Radio Mode) Press the button to select AM or FM Modes. Setting the Tone, Balance, and Fade Press the rotary TUNE control and BASS will display. Turn the TUNE control to the right or left to increase or decrease the Bass tones. Press the rotary TUNE control a second time and MID will display. Turn the TUNE control to the right or left to increase or decrease the Mid Range tones. Press the rotary TUNE control a third time and TREBLE will display.
UNDERSTANDING YOUR INSTRUMENT PANEL 177 Toggle the PTY button to select the following format types: Program Type No program type or undefined Adult Hits Alert Alert Classical Classic Rock College Country Emergency Test Foreign Language Information Jazz News 16 Digit-Character Display None Adult_Hits Alert Alert Classical Classic_Rock College Country Emergency Test Foreign_Language Information Jazz News Program Type Nostalgia Oldies Personality Public Rhythm and Blues Religious Music Religious Talk Rock S
178 UNDERSTANDING YOUR INSTRUMENT PANEL By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to the next frequency station with the same selected PTY name. The PTY function only operates when in the FM mode. If a preset button is activated while in the PTY (Program Type) mode, the PTY mode will be exited and the radio will tune to the preset station.
UNDERSTANDING YOUR INSTRUMENT PANEL 179 Operation Instructions - (CD MODE for CD Audio Play) NOTE: • The ignition switch must be in the ON or ACC position to operate the radio. • Note: This Radio is capable of playing compact discs (CD), recordable compact discs (CD-R), rewritable compact discs (CD-RW) compact discs with MP3 tracks and multisession compact discs with CD and MP3 tracks. Inserting Compact Disc(s) Gently insert one CD into the CD player with the CD label facing up.
180 UNDERSTANDING YOUR INSTRUMENT PANEL SEEK Button (CD MODE for CD Audio Play) Press the right side of the SEEK button for the next selection on the CD. Press the left side of the button to return to the beginning of the current selection, or return to the beginning of the previous selection if the CD is within the first 10 seconds of the current selection. MUTE Button (CD MODE for CD Audio Play) Press the MUTE button to cancel the sound from the speakers. ⬙MUTE⬙ will be displayed.
UNDERSTANDING YOUR INSTRUMENT PANEL 181 Radio display will show ⬙EJECTING DISC⬙ when the disc is being ejected and prompt the user to remove the disc. Press and hold the LOAD/ EJECT button for 5 seconds and all CDs will be ejected from the radio. If you have ejected a disc and have not removed it within 15 seconds, it will be reloaded. If the CD is not removed, the radio will continue to play the non-removed CD.
182 UNDERSTANDING YOUR INSTRUMENT PANEL RND/PTY Button (Random Play Button) (CD MODE for CD Audio Play) Press this button while the CD is playing to activate Random Play. This feature plays the selections on the compact disc in random order to provide an interesting change of pace. Press the SEEK button to move to the next randomly selected track. Press and hold the FF button to fast forward through the tracks. Release the FF button to stop the fast forward feature.
UNDERSTANDING YOUR INSTRUMENT PANEL 183 • Maximum number of folders: 100 • Maximum number of characters in file/folder names: • Level 1: 12 (including a separator ⬙.⬙ and a 3-character extension) • Level 2: 31 (including a separator ⬙.⬙ and a 3-character extension) Multisession disc formats are supported by the radio. Multisession discs may contain combinations of normal CD audio tracks and computer files (including MP3 files).
184 UNDERSTANDING YOUR INSTRUMENT PANEL ID3 Tag information for artist, song title and album title are supported for version 1 ID3 tags. ID3 version 2 is not supported by the radios. Playlist files are not supported. MP3 Pro files are not supported. Playback of MP3 Files When a medium containing MP3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3 files.
UNDERSTANDING YOUR INSTRUMENT PANEL 185 LOAD/EJECT Button (CD Mode for MP3 Play) LOAD/ EJECT - Load Press the LOAD/ EJECT button and the pushbutton with the corresponding number where the CD is being loaded. The radio will display PLEASE WAIT and prompt when to INSERT DISC. After the radio displays ⬙LOAD DISC⬙ insert the CD into the player. Radio display will show ⬙LOADING DISC⬙ when the disc is loading.
186 UNDERSTANDING YOUR INSTRUMENT PANEL Press and hold the MSG or INFO button while in the message display priority mode or elapsed time display priority mode will display the song title for each file. Turn the TUNE control to display available folders or move through available folders. Press the TUNE control to select a folder. RW/FF (CD Mode for MP3 Play) Press the FF side of the button to move forward through the MP3 selection.
UNDERSTANDING YOUR INSTRUMENT PANEL 187 SALES CODE REF — AM/FM/CD (SINGLE-DISC) RADIO WITH OPTIONAL SATELLITE RADIO AND HANDS-FREE PHONE CAPABILITY NOTE: The radio sales code is located on the lower right side of your radio faceplate. Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Control (Rotary) Press the ON/VOL control to turn the radio ON. Press the ON/VOL a second time to turn OFF the radio.
188 UNDERSTANDING YOUR INSTRUMENT PANEL Mode Button (Radio Mode) Press the MODE button repeatedly to select between the CD player and Satellite Radio (if equipped). SEEK Button (Radio Mode) Press and release the SEEK button to search for the next listenable station in either AM/FM or Satellite (if equipped) mode. Press the right side of the button to seek up and the left side to seek down. The radio will remain tuned to the new station until you make another selection.
UNDERSTANDING YOUR INSTRUMENT PANEL 189 Clock Setting Procedure 1. Press and hold the TIME button until the hours blink. 2. Adjust the hours by turning the TUNE/AUDIO control. 3. After the hours are adjusted, press the TUNE/AUDIO control to set the minutes. The minutes will begin to blink. 4. Adjust the minutes using the TUNE/AUDIO control. 5. To exit, press any button/knob or wait five seconds.
190 UNDERSTANDING YOUR INSTRUMENT PANEL Press the rotary TUNE control a fourth time and BAL will display. Turn the TUNE control to the right or left to adjust the sound level from the right or left side speakers. selected within five seconds after pressing the SET button, the station will continue to play but will not be stored into pushbutton memory. Press the rotary TUNE control a fifth time and FADE will display.
UNDERSTANDING YOUR INSTRUMENT PANEL 191 Operating Instructions - CD Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Inserting The Compact Disc (Single CD Player) Gently insert one CD into the CD player with the CD label facing up. The CD will automatically be pulled into the CD Player and the CD icon will illuminate on the radio display. If the volume control is ON, the unit will switch to CD mode and begin to play.
192 UNDERSTANDING YOUR INSTRUMENT PANEL SCAN Button (CD Mode) Press this button to play the first 10 seconds of each track. To stop the scan function, press the button a second time. EJECT Button (CD Mode) Press this button and the disc will unload and move to the entrance for easy removal. The unit will switch to the last selected mode. If you do not remove the disc within 15 seconds, it will be reloaded. The radio mode will continue to appear.
UNDERSTANDING YOUR INSTRUMENT PANEL 193 MP3 player, cassette player, or microphone and utilize the vehicle’s audio system to amplify the source and play through the vehicle speakers. second time and the sound from the speakers will return. Rotating the volume control or turning the ignition OFF/ON will also return the sound from the speakers. The auxiliary mode becomes active when an electrical device is plugged into the AUX jack using a standard 3.
194 UNDERSTANDING YOUR INSTRUMENT PANEL RW/FF (Auxiliary Mode) No function. RND/SET Button (Auxiliary Mode) No function. SALES CODE REC — AM/FM/CD (6–DISC) RADIO WITH NAVIGATION SYSTEM Mode Button (Auxiliary Mode) Press the MODE button repeatedly to select between the CD player and Satellite Radio (if equipped). Operating Instructions - Hands-Free Phone — If Equipped Refer to the “Hands-Free Phone (UConnect威)” section of this Owner’s Manual.
UNDERSTANDING YOUR INSTRUMENT PANEL 195 menus and instructions for selecting a variety of destinations and routes, AM/FM stereo radio and six-disc CD changer with MP3 capability. the worldwide standard for time. This makes the system’s clock very accurate once the appropriate time zone and daylight savings information is set. Mapping information for navigation is supplied on a DVD that is loaded into the unit. One map DVD covers all of North America.
196 UNDERSTANDING YOUR INSTRUMENT PANEL 2. To show the GPS clock, select “Displayed Clock: GPS Clock” and press ENTER. 3. To adjust the time zone, Select “Time Zone” and press ENTER. Select the appropriate time zone and press ENTER. 4. To turn daylight savings on or off, select “Daylight Savings” and press ENTER. Select “On” or “Off” and press ENTER. 5. Select DONE to exit from the clock setting mode. Press ENTER to save your changes. If you press CANCEL or NAV then your changes will not be saved.
UNDERSTANDING YOUR INSTRUMENT PANEL 197 3. To decrease the clock by one hour, use the Select Encoder to highlight the “-” sign. Press ENTER. Press ENTER again to decrease the clock by another hour. Radio. This service offers over 130 channels of music, sports, news, entertainment, and programming for children, directly from its satellites and broadcasting studios. 4. To increase the clock by minutes, make sure “MIN +” is highlighted and press ENTER.
198 UNDERSTANDING YOUR INSTRUMENT PANEL number 888-539-7474, or visit the Sirius web site at www.sirius.com, or at www.siriuscanada.ca for Canadian residents. Electronic Serial Number/Sirius Identification Number (ESN/SID) Please have the following information available when calling: 1. The Electronic Serial Number/Sirius Identification Number (ESN/SID). 2. Your Vehicle Identification Number. To access the ESN/SID, refer to the following procedure.
UNDERSTANDING YOUR INSTRUMENT PANEL 199 With the ignition in the ACC position and the radio off, press the CD Eject and SET buttons simultaneously until the 12 digits of the ESN/SID appear on the screen. Selecting Satellite Mode in REF, RAQ, And RAK Radios Selecting Satellite Mode — REF Radio Press the MODE button repeatedly until the word ⬙SAT⬙ appears in the display. A CD may remain in the radio while in the Satellite radio mode.
200 UNDERSTANDING YOUR INSTRUMENT PANEL Storing And Selecting Preset Channels In addition to the 12 AM and 12 FM preset stations, you may also commit 12 satellite stations to pushbutton memory. These satellite channel preset stations will not erase any AM or FM preset memory stations. Follow the memory preset procedures that apply to your radio. Using The PTY (Program Type) Button — If Equipped Follow the PTY button instructions that apply to your radio.
UNDERSTANDING YOUR INSTRUMENT PANEL 201 Reception Quality Satellite reception may be interrupted due to one of the following reasons: • The vehicle is parked in an underground parking structure or under a physical obstacle. • Dense tree coverage may interrupt reception. • Driving under wide bridges or along tall buildings can cause intermittent reception. front row seat. Refer to your VES™ User’s Manual for detailed operating instructions.
202 UNDERSTANDING YOUR INSTRUMENT PANEL The right-hand control is a rocker type switch with a button in the center. Pressing the top of the switch will increase the volume and pressing the bottom of the switch will decrease the volume. The center button of the right-hand control will allow you to change the mode. The left-hand control is a rocker type switch with a push button in the center. The function of the left-hand control is different, depending on which mode you are in.
UNDERSTANDING YOUR INSTRUMENT PANEL 203 If you press the switch up or down twice it plays the second track, three times, it will play the third, etc. The button in the center of the left-hand switch has no function in this mode. CD/DVD MAINTENANCE To keep a CD/DVD in good condition, take the following precautions: 1. Handle the disc by its edge; avoid touching the surface. 2. If the disc is stained, clean the surface with a soft cloth, wiping from center to edge. 3.
204 UNDERSTANDING YOUR INSTRUMENT PANEL CLIMATE CONTROLS The controls for the heating and ventilation system in this vehicle consist of a series of rotary knobs. These comfort controls can be set to obtain desired interior conditions.
UNDERSTANDING YOUR INSTRUMENT PANEL 205 NOTE: To improve your selection choices, the system allows you to operate at intermediate positions between the major modes. These intermediate positions are identified by the small dots. Bi-Level Outside air flows through the outlets located in the instrument panel and at the floor. Panel Outside air flows through the outlets located in the instrument panel. Outside air flows in equal proportions through the floor and defroster outlets.
206 UNDERSTANDING YOUR INSTRUMENT PANEL Blower Control The rotary knob on the left of the control panel is the blower control. Turn the knob clockwise to one of the four positions to obtain the blower speed you desire. To turn the blower off, turn the knob to the far left position. NOTE: For vehicles equipped with Remote Start, the climate controls will not function during Remote Start operation if the blower control is left in the “O” (Off) position.
UNDERSTANDING YOUR INSTRUMENT PANEL 207 Air Conditioning and Heating — If Equipped outlets selected by the mode control. A light in the snowflake button shows that the air conditioning is on. Press the button a second time to turn the air conditioning off. Slight changes in engine speed or power may be noticed when the air conditioning compressor is on. This is a normal occurrence, as the compressor will cycle on and off to maintain comfort and increase fuel economy.
208 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: To improve your selection choices, the system allows you to operate at intermediate positions between the major modes. These intermediate positions are identified by the small dots. Bi-Level Outside air flows through the outlets located in the instrument panel and at the floor. Recirculation Modes (Panel or Bi-Level) Select the recirculation modes when the outside air contains smoke, odors, high humidity, or if rapid cooling is desired.
UNDERSTANDING YOUR INSTRUMENT PANEL 209 Blower Control The rotary knob on the left of the control panel is the blower control. Turn the knob clockwise to one of the four positions to obtain the blower speed you desire. To turn the blower off, turn the knob to the far left position. Temperature Control The rotary knob at the center of the control panel controls the temperature of the interior air. You can choose your degree of comfort by rotating the knob.
210 UNDERSTANDING YOUR INSTRUMENT PANEL Air Conditioning With Dual Zone Temperature Control — If Equipped With the Dual Zone Temperature Control System, each front seat occupant can independently control the temperature of air coming from the outlets on their side of the vehicle. Air Conditioning and Heating Operation To turn on the air conditioning, set the fan control at any speed and press the snowflake button located on the control panel.
UNDERSTANDING YOUR INSTRUMENT PANEL 211 Recirculation Pushbutton Pushing the Recirculation button allows interior air to recirculate continuously in any position except defrost and defrost/floor mode for rapid cool down of the interior. Refer to “Fast Cooldown” in this section. Mode Control The mode control allows you to choose from several patterns of air distribution. NOTE: To improve your selection choices, the system allows you to operate at intermediate positions between the major modes.
212 UNDERSTANDING YOUR INSTRUMENT PANEL Mix Blower Control Outside air flows in equal proportions through the floor and defroster outlets. Defrost Outside air is primarily directed to the windshield through the defroster outlets located at the base of the windshield and side window demist outlets. NOTE: The air conditioning compressor operates in both Mix and Defrost or a blend of these modes, even if the A/C button has not been pressed. This dehumidifies the air to help dry the windshield.
UNDERSTANDING YOUR INSTRUMENT PANEL 213 Dual Zone Temperature Control Circulation The cab is designed with features to promote outside air circulation. There are grilles in the cab back panel. These are air exhausters that provide the means for regular exchange of cab air. Side window demisters direct air flow specifically to the window glass to help prevent interior fogging of the glass. They are located in the extreme outside upper edges of the instrument panel.
214 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Tips Fast Cooldown For a fast cooldown, turn the blower fan rotary knob to the extreme right position, turn the mode control to the panel fresh position, press the snowflake button to turn on the air conditioning, and drive with the windows open for the first few minutes.
UNDERSTANDING YOUR INSTRUMENT PANEL 215 smoke, perfumes, etc.) from sticking to the windows. Contaminates increase the rate of window fogging. Summer Operation Air conditioned vehicles must be protected with a high quality antifreeze coolant during summer to provide proper corrosion protection and to raise the boiling point of the coolant for protection against overheating. A 50 % concentration is recommended. Refer to ”Engine Coolant” under “ Fluids, Lubricants and Genuine Parts” in section 7.
216 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Tips Chart
STARTING AND OPERATING CONTENTS 䡵 Starting Procedures . . . . . . . . . . . . . . . . . . . . 221 䡵 Four-Wheel Drive Operation — If Equipped . . 230 ▫ Normal Starting . . . . . . . . . . . . . . . . . . . . . 221 ▫ Manually Shifted Transfer Case Operating Information/Precautions . . . . . . . . . . . . . . . 230 ▫ Automatic Transmission . . . . . . . . . . . . . . . 221 ▫ If Engine Fails To Start . . . . . . . . . . . . . . . . 222 ▫ After Starting . . . . . . . . . . . . . . . . . . . . . . .
218 STARTING AND OPERATING ▫ Electronically Shifted Transfer Case Operating Information/Precautions (4 Position Switch) — If Equipped . . . . . . . . . . 242 ▫ Shifting Procedure — Electronically Shifted Transfer Case . . . . . . . . . . . . . . . . . . . . . . . 246 䡵 Limited-Slip Differential – If Equipped . . . . . . 249 䡵 Driving On Slippery Surfaces . . . . . . . . . . . . . 250 ▫ Four-Wheel Anti-Lock Brake System . . . . . . . 256 䡵 Tire Safety Information . . . . . . . . . . . . . . . . .
STARTING AND OPERATING 219 䡵 Supplemental Tire Pressure Information — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 276 䡵 Tire Chains . . . . . . . . . . . . . . . . . . . . . . . . . . 276 ▫ Common Towing Definitions . . . . . . . . . . . . 289 ▫ Trailer Hitch Classification . . . . . . . . . . . . . . 292 䡵 Snow Tires . . . . . . . . . . . . . . . . . . . . . . . . . . 278 ▫ Trailer Towing Weights (Maximum Trailer Weight Ratings) . . . . . . . . . . . . . . . . . . . . .
220 STARTING AND OPERATING 䡵 Recreational Towing (Behind Motorhome, Etc.) . 304 ▫ Recreational Towing – 2-Wheel Drive Models . . . . . . . . . . . . . . . . . 304 ▫ Recreational Towing – 4-Wheel Drive Models . . . . . . . . . . . . . . . . .
STARTING AND OPERATING 221 STARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. The starter should not be operated for more than 15second intervals. Waiting a few seconds between such intervals will protect the starter from overheating. WARNING! • Be sure to turn off the engine and remove the key from the ignition switch if you want to rest or sleep in your vehicle.
222 STARTING AND OPERATING NOTE: This vehicle is equipped with a transmission shift interlocking system. The brake pedal must be depressed to shift out of PARK. Tip Start Feature Do not press the accelerator. Turn the ignition key briefly to START position, and release it. The starter motor will continue to run, but will automatically disengage when the engine is running. If Engine Fails To Start If the engine fails to start after you have followed the “Normal Starting” procedure, it may be flooded.
STARTING AND OPERATING 223 WARNING! (Continued) • If the vehicle has a discharged battery, booster cables may be used to obtain a start from a booster battery or the battery in another vehicle. This type of start can be dangerous if done improperly. Refer to “Jump Starting” in Section 6. If the engine has been flooded, it may start to run, but not have enough power to continue running when the key is released. If this occurs, continue cranking with the accelerator pedal pushed all the way to the floor.
224 STARTING AND OPERATING AUTOMATIC TRANSMISSION CAUTION! Damage to the transmission may occur if the following precautions are not observed: • Shift into PARK only after the vehicle has come to a complete stop. • Shift into or out of REVERSE only after the vehicle has come to a complete stop and the engine is at idle speed. • Do not shift from REVERSE, PARK, or NEUTRAL into any forward gear when the engine is above idle speed.
STARTING AND OPERATING 225 DRIVE position. Pull the shift lever toward you when shifting into REVERSE, SECOND, FIRST or PARK, or when shifting out of PARK. Gear Ranges DO NOT race the engine when shifting from PARK or NEUTRAL position into another gear range. PARK This gear position supplements the parking brake by locking the transmission. The engine can be started in this range. Never use PARK while the vehicle is in motion. Apply the parking brake when leaving the vehicle in this range.
226 STARTING AND OPERATING WARNING! (Continued) • It is dangerous to move the shift lever out of PARK or NEUTRAL if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in reverse. You could lose control of the vehicle and hit someone or something. Only shift into gear when the engine is idling normally and when your right foot is firmly on the brake pedal.
STARTING AND OPERATING 227 NOTE: Use caution when operating a heavily loaded vehicle in SECOND or FIRST gear selections in high ambients as torque converter slip can impose significant additional heat load on the cooling system. Overdrive Operation The overdrive automatic transmission contains an electronically controlled fourth and fifth (if equipped) speed (Overdrive).
228 STARTING AND OPERATING The transmission will downshift from Overdrive to DRIVE if the accelerator pedal is fully depressed at vehicle speeds above approximately 35 mph (56 km/h). When To Use “TOW HAUL” and “O/D OFF” Modes When driving in hilly areas, towing a trailer, carrying a heavy load, etc., and frequent transmission shifting occurs, press the “TOW HAUL O/D OFF” button once to select TOW HAUL.
STARTING AND OPERATING 229 economy) and automatic closed-throttle downshifts to 3rd gear are performed (for improved braking) when driving conditions warrant. Pressing the “TOW HAUL O/D OFF” button a second time to select O/D OFF will disable 4th and 5th gear completely, which should eliminate any excessive transmission shifting. The “TOW HAUL” or “O/D OFF” light will illuminate in the instrument cluster to indicate when the switch has been activated.
230 STARTING AND OPERATING the transmission. This condition is normal and will not cause damage to the transmission. The torque converter will refill within five seconds of shifting from PARK into any other gear position. FOUR-WHEEL DRIVE OPERATION — IF EQUIPPED Four-wheel drive trucks are equipped with either a manually shifted transfer case or an electronically shifted transfer case. Refer to the operating instructions for your transfer case, located in this section.
STARTING AND OPERATING 231 at a given road speed. Take care not to overspeed the engine and do not exceed 25 mph (40 km/h). Proper operation of 4-wheel drive vehicles depends on tires of equal size, type and circumference on each wheel. Any difference will adversely affect shifting and can cause damage to the transfer case. NOTE: Do not attempt to make a shift while only the front or rear wheels are spinning.
232 STARTING AND OPERATING For additional information on the appropriate use of each transfer case mode position see the information below: 2H Rear Wheel Drive High Range - Normal street and highway driving. Dry hard surfaced roads. 4H 4-Wheel Drive High Range - Locks the front and rear driveshafts together. Forces the front and rear wheels to rotate at the same speed. Additional traction for loose, slippery road surfaces only.
STARTING AND OPERATING 233 Shifting Procedure - Manually Shifted Transfer Case vehicle in motion, the transfer case will engage/ disengage faster if you momentarily release the accelerator pedal after completing the shift. Apply a constant force when shifting the transfer case lever. 2H or 4H ⇔ 4L With the vehicle rolling at 2 to 3 mph (3 to 5 km/h), shift the transmission into NEUTRAL. While the vehicle is coasting at 2 to 3 mph (3 to 5 km/h), shift the transfer case lever firmly to the desired position.
234 STARTING AND OPERATING • Shifting into or out of 4L is possible with the vehicle completely stopped, however difficulty may occur due to the mating clutch teeth not being properly aligned. Several attempts may be required for clutch teeth alignment and shift completion to occur. The preferred method is with the vehicle rolling 2 to 3 mph (3 to 5 km/h). Avoid attempting to engage or disengage 4L with the vehicle moving faster than 2 to 3 mph (3 to 5 km/h).
STARTING AND OPERATING 235 This Electronically Shifted transfer case provides 5 mode positions: 2-wheel drive (2WD), 4WD AUTO, 4WD LOCK, NEUTRAL and 4WD LOW. The Electronically Shifted transfer case is designed to be driven in the 2 wheel drive position (2WD) or 4-wheel drive position (4WD AUTO) for normal street and highway conditions (dry hard surfaced roads). Driving the vehicle in 2WD will have greater fuel economy benefits, as the front axle is not engaged in 2WD.
236 STARTING AND OPERATING towing only. Refer to “Recreational Towing” in this section for specific procedures on shifting into and out of NEUTRAL. Transfer Case Position Indicator Lights — Electronically Shifted Transfer Case Only Transfer case position indicator lights are located on the instrument cluster and indicate the current and desired transfer case selection.
STARTING AND OPERATING 237 If One or More Shift Conditions are not Met 1. The indicator light for the current position will remain ON. 2. The newly selected position indicator light will continue to flash. 3. The transfer case will not shift. NOTE: Before retrying a selection, make certain that all the necessary requirements for selecting a new transfer case position have been met. To retry the selection, turn the control knob back to the current position, wait five seconds, and retry selection.
238 STARTING AND OPERATING Proper operation of 4-wheel drive vehicles depends on tires of equal size, type and circumference on each wheel. Any difference in tire size can cause damage to the transfer case. Because 4-wheel drive provides improved traction, there is a tendency to exceed safe turning and stopping speeds. Do not go faster than road conditions permit.
STARTING AND OPERATING 239 4WD LOW 4-Wheel Drive Low Range - Low speed 4-wheel drive. Locks the front and rear driveshafts together. Forces the front and rear wheels to rotate at the same speed. Additional traction and maximum pulling power for loose, slippery road surfaces only. Do not exceed 25 mph (40 km/h). Shifting Procedure — Electronically Shifted Transfer Case N NEUTRAL - Disengages both the front and rear driveshafts from the powertrain. To be used for flat towing behind another vehicle.
240 STARTING AND OPERATING remain ON and the newly selected position indicator light will continue to flash until all the requirements for the selected position have been met. To retry a shift: return the control knob back to the original position, make certain all shift requirements have been met, wait five seconds and try the shift again.
STARTING AND OPERATING 241 3. While still rolling, rotate the transfer case control switch to the desired position. 4. After the desired position indicator light is ON (not flashing), shift transmission back into gear. Alternate Procedure 1. Bring the vehicle to complete stop. 2. With the key ON and the engine either OFF or RUNNING, shift the transmission into NEUTRAL.
242 STARTING AND OPERATING Electronically Shifted Transfer Case Operating Information/Precautions (4 Position Switch) — If Equipped This is an electric shift transfer case and is operated by the 4WD Control Switch (Transfer Case Switch), which is located on the instrument panel. This Electronically Shifted transfer case provides four mode positions: 2 (rear)-wheel drive high range, 4-wheel drive lock range, 4-wheel drive low range, and NEUTRAL.
STARTING AND OPERATING 243 positions on dry hard surfaced roads may cause increased tire wear and damage to the driveline components. case NEUTRAL position is to be used for recreational towing only. Refer to “Recreational Towing” in this section. Transfer Case Position Indicator Lights — Electronically Shifted Transfer Case Only Transfer case position indicator lights are located in the instrument cluster and indicate the current and desired transfer case selection.
244 STARTING AND OPERATING If One or More Shift Conditions Are Not Met: 1. The indicator light for the current position will remain ON. 2. The newly selected position indicator light will continue to flash. 3. The transfer case will not shift. NOTE: Before retrying a selection, make certain that all the necessary requirements for selecting a new transfer case position have been met. To retry the selection, turn the control knob back to the current position, wait five seconds, and retry selection.
STARTING AND OPERATING 245 4WD LOCK positions at a given road speed. Take care not to overspeed the engine and do not exceed 25 mph (40 km/h). Proper operation of 4-wheel drive vehicles depends on tires of equal size, type and circumference on each wheel. Any difference in tire size can cause damage to the transfer case. Because 4-wheel drive provides improved traction, there is a tendency to exceed safe turning and stopping speeds. Do not go faster than road conditions permit.
246 STARTING AND OPERATING 4WD LOCK 4-Wheel Drive Lock Range - Locks the front and rear driveshafts together. Forces the front and rear wheels to rotate at the same speed. Additional traction for loose, slippery road surfaces only. Shifting Procedure — Electronically Shifted Transfer Case 4WD LOW 4-Wheel Drive Low Range - Low speed 4-wheel drive. Locks the front and rear driveshafts together. Forces the front and rear wheels to rotate at the same speed.
STARTING AND OPERATING 247 remain ON and the newly selected position indicator light will continue to flash until all the requirements for the selected position have been met. To retry a shift: return the control knob back to the original position, make certain all shift requirements have been met, wait five seconds and try the shift again.
248 STARTING AND OPERATING Shifting can be performed with the vehicle rolling 2 to 3 mph (3 to 5 km/h) or completely stopped. USE EITHER OF THE FOLLOWING PROCEDURES: Preferred Procedure 1. With engine running, slow vehicle to 2 to 3 mph (3 to 5 km/h). 2. Shift the transmission into NEUTRAL. 3. While still rolling, rotate the transfer case control switch to the desired position. 4. After the desired position indicator light is ON (not flashing), shift transmission back into gear. Alternate Procedure 1.
STARTING AND OPERATING 249 LIMITED-SLIP DIFFERENTIAL – IF EQUIPPED The limited-slip differential provides additional traction on snow, ice, mud, sand and gravel, particularly when there is a difference between the traction characteristics of the surface under the right and left rear wheels. During normal driving and cornering, the limited-slip unit performs similarly to a conventional differential.
250 STARTING AND OPERATING DRIVING ON SLIPPERY SURFACES When driving on wet or slushy roads, it is possible for a wedge of water to build up between the tire and road surface. This is known as hydroplaning and may cause partial or complete loss of vehicle control and stopping ability. To reduce this possibility, the following precautions should be observed: 1. Slow down during rainstorms or when roads are slushy. 2. Slow down if the road has standing water or puddles. 3.
STARTING AND OPERATING 251 Shallow Standing Water Although your vehicle is capable of driving through shallow standing water, consider the following Caution and Warning before doing so. CAUTION! • Always check the depth of the standing water before driving through it. Never drive through standing water that is deeper than the bottom of the tire rims mounted on the vehicle.
252 STARTING AND OPERATING WARNING! • Driving through standing water limits your vehicle’s traction capabilities. Do not exceed 5 mph (8 km/h) when driving through standing water. • Driving through standing water limits your vehicle’s braking capabilities, which increases stopping distances. Therefore, after driving through standing water, drive slowly and lightly press on the brake pedal several times to dry the brakes.
STARTING AND OPERATING 253 WARNING! Continued operation with reduced power steering assist could pose a safety risk to yourself and others. Service should be obtained as soon as possible. apparent, and/or the system is not functioning as anticipated. Coordinate inspection efforts through an authorized dealer. No chemical flushes should be used in any power steering system; only the approved lubricant may be used.
254 STARTING AND OPERATING PARKING BRAKE The foot-operated parking brake is positioned below the lower left corner of the instrument panel. To release the parking brake, pull the parking brake release handle. NOTE: The instrument cluster red brake warning light will come on and flash to indicate that the parking brake is applied. You must be sure that the parking brake is fully applied before leaving the vehicle.
STARTING AND OPERATING 255 WARNING! • Always fully apply the parking brake when leaving your vehicle, or it may roll and cause damage or injury. Also be certain to leave the transmission in PARK. Failure to do so may allow the vehicle to roll and cause damage or injury. • Never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Do not leave the key in the ignition.
256 STARTING AND OPERATING Four-Wheel Anti-Lock Brake System WARNING! (Continued) WARNING! • Anti-Lock Brake Systems (ABS) contain sophisticated electronic equipment. It may be susceptible to interference caused by improperly installed or high output radio transmitting equipment. This interference can cause possible loss of anti-lock braking capability. Installation of such equipment should be performed by qualified professionals.
STARTING AND OPERATING 257 The system’s pump motor runs during an ABS stop to provide regulated hydraulic pressure. The pump motor makes a low humming noise during operation. This is normal. When you are in a severe braking condition involving use of the ABS, you will experience some pedal drop as the vehicle comes to a complete stop. This is the result of the system reverting to the base brake system and is normal. Engagement of the ABS may be accompanied by a pulsing sensation in the brake pedal.
258 STARTING AND OPERATING TIRE SAFETY INFORMATION Tire Markings NOTE: • P (Passenger) - Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designation. Example: P215/65R15 95H. • European-Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter ⬙P⬙ is absent from this tire size designation.
STARTING AND OPERATING 259 molded into the sidewall preceding the size designation. Example: T145/80D18 103M. • High flotation tire sizing is based on U.S. design standards and it begins with the tire diameter molded into the sidewall. Example: 31x10.5 R15 LT. Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ⴖ....blank....ⴖ = Passenger car tire based on European design standards LT = Light truck tire based on U.S.
260 STARTING AND OPERATING EXAMPLE: Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions — The maximum speed corresponding to the speed symbol should only be achieved under specified operating conditions (i.e.
STARTING AND OPERATING 261 Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full TIN, including the date code, located on the white sidewall side of the tire. Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the outboard side, then you will find it on the inboard side of the tire.
262 STARTING AND OPERATING Tire Loading and Tire Pressure Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar. Tire and Loading Information Placard This placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) total weight your vehicle can carry 3) tire size designed for your vehicle 4) cold tire inflation pressures for the front, rear, and spare tires.
STARTING AND OPERATING 263 To determine the maximum loading conditions of your vehicle, locate the statement “The combined weight of occupants and cargo should never exceed XXX lbs or XXX kg” on the Tire and Loading Information placard. The combined weight of occupants, cargo/luggage and trailer tongue weight (if applicable) should never exceed the weight referenced here. Steps for Determining Correct Load Limit 1.
264 STARTING AND OPERATING 6. If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle. NOTE: • The following table shows examples on how to calculate total load, cargo/luggage, and towing capacities of your vehicle with varying seating configurations and number and size of occupants.
STARTING AND OPERATING 265 5
266 STARTING AND OPERATING WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.
STARTING AND OPERATING 267 WARNING! (Continued) • Unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • Always drive with each tire inflated to the recommended cold tire inflation pressure. Economy Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement.
268 STARTING AND OPERATING CAUTION! After inspecting or adjusting the tire pressure, always reinstall the valve stem cap (if equipped). This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressures specified on the placard are always “cold tire inflation pressure.” Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least three hours, or driven less than 1 mile (1 km) after a three hour period.
STARTING AND OPERATING 269 Tire Inflation Pressure — 4500/5500 with Steel Carcass Ply Tires This type of tire utilizes steel cords in the sidewall. As such, they cannot be treated like normal light truck tires. Adjusting tire pressure must be performed by personnel trained, supervised and equipped accordingly.
270 STARTING AND OPERATING 4500/5500 Tire Inflation
STARTING AND OPERATING 271 When adjusting inflation pressure to a tire and wheel assembly mounted on a vehicle, use Remote Mount Automatic Inflation Kit (similar to model number #27cc1021234, available from TEAM PSE (PENTASTAR Service Equipment-Phone number 1-800-734-4334). NOTE: Never attempt to re-inflate a tire and wheel assembly which has been run flat or is extremely underinflated without first removing the tire from the wheel assembly for inspection.
272 STARTING AND OPERATING WARNING! High speed driving with your vehicle under maximum load is dangerous. The added strain on your tires could cause them to fail. You could have a serious accident resulting in serious injury or death. Don’t drive a vehicle loaded to the maximum capacity at continuous speeds above 75 mph (120 km/h). Radial Ply Tires WARNING! Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly.
STARTING AND OPERATING 273 Tire Spinning When stuck in mud, sand, snow, or ice conditions, do not spin your vehicle’s wheels faster than 30 mph (48 km/h) or for longer than 30 seconds continuously without stopping when you are stuck. Tread Wear Indicators Tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced. Refer to “Freeing A Stuck Vehicle” in Section 6 of this manual. WARNING! Fast spinning tires can be dangerous.
274 STARTING AND OPERATING These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes 1/16 in (2 mm). When the tread is worn to the tread wear indicators, the tire should be replaced. Many states have laws requiring tire replacement at this point.
STARTING AND OPERATING 275 Information placard for the size designation of your tire. The service description and load identification will be found on the original equipment tire. Failure to use equivalent replacement tires may adversely affect the safety, handling, and ride of your vehicle. We recommend that you contact your original equipment or an authorized tire dealer with any questions you may have on tire specifications or capability.
276 STARTING AND OPERATING WARNING! (Continued) • Never use a tire with a smaller load index or capacity, other than what was originally equipped on your vehicle. Using a tire with a smaller load index could result in tire overloading and failure. You could lose control and have an accident resulting in serious injury or death. • Failure to equip your vehicle with tires having adequate speed capability can result in sudden tire failure and loss of vehicle control resulting in serious injury or death.
STARTING AND OPERATING 277 CAUTION! (Continued) CAUTION! (Continued) • Because of limited chain clearance between tires and other suspension components, it is important that only chains in good condition are used. Broken chains can cause serious vehicle damage. Stop the vehicle immediately if noise occurs that could suggest chain breakage. Remove the damaged parts of the chain before further use. • Install chains as tightly as possible and then retighten after driving about 1/2 mi (0.8 km).
278 STARTING AND OPERATING • On 4X2 vehicles, class “U” snow chains are permitted on the rear wheels only of vehicles equipped with LT245/70R17, LT265/70R17, and LT235/80R17 size tires. • On 4X4 Single Rear Wheel (SRW) vehicles, class “U” snow chains are permitted on the rear wheels only on vehicles equipped with LT265/70R17.
STARTING AND OPERATING 279 TIRE ROTATION RECOMMENDATIONS Tires on the front and rear axles of vehicles operate at different loads and perform different steering, driving, and braking functions. For these reasons, they wear at unequal rates, and develop irregular wear patterns. These effects can be reduced by timely rotation of tires. The benefits of rotation are especially worthwhile with aggressive tread designs such as those on On/Off Road type tires.
280 STARTING AND OPERATING Dual Rear Wheels The tires used on dual wheel assemblies should be matched for wear to prevent overloading one tire in a set. To check if tires are even, lay a straight edge across all four tires. The straight edge should touch all the tires. CAUTION! 4500/5500 Dual Rear Tires have only one approved direction of rotation. This is to accommodate the asymmetrical design (tread pattern) of the On/Off road tire.
STARTING AND OPERATING 281 FUEL REQUIREMENTS 5.7L Gas Engine The 5.7L engine is designed to meet all emissions regulations and provide satisfactory fuel economy and performance when using high quality unleaded gasoline having an octane range of 87 to 89. The manufacturer recommends the use of 89 octane for optimum performance. The use of premium gasoline is not recommended.
282 STARTING AND OPERATING We strongly support the use of reformulated gasolines. Properly blended reformulated gasolines will provide excellent performance and durability for the engine and fuel system components. Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with oxygenates such as 10% ethanol, MTBE, and ETBE. Oxygenates are required in some areas of the country during the winter months to reduce carbon monoxide emissions.
STARTING AND OPERATING 283 allowed in the United States. MMT is prohibited in Federal and California reformulated gasoline. Materials Added To Fuel All gasolines sold in the United States are required to contain effective detergent additives. Use of additional detergents or other additives is not needed under normal conditions and would result in unnecessary cost. Therefore, you should not have to add anything to the fuel.
284 STARTING AND OPERATING CAUTION! (Continued) • The use of fuel additives which are now being sold as octane enhancers is not recommended. Many of these products contain high concentrations of methanol. Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsibility of the manufacturer. NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you.
STARTING AND OPERATING 285 WARNING! (Continued) CAUTION! • Guard against carbon monoxide with proper maintenance. Have the exhaust system inspected every time the vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side windows fully open. • Damage to the fuel system or emissions control system could result from using an improper fuel tank filler tube cap (gas cap). A poorly fitting cap could let impurities into the fuel system.
286 STARTING AND OPERATING WARNING! WARNING! • Never have any smoking materials lit in or near the vehicle when the gas cap is removed or the tank filled. • Never add fuel to the vehicle when the engine is running. This is in violation of most state and federal fire regulations and will cause the MIL to turn on. A fire may result if gasoline is pumped into a portable container that is inside of a vehicle. You could be burned. Always place gas containers on the ground while filling.
STARTING AND OPERATING 287 VEHICLE LOADING Certification Label As required by National Highway Traffic Safety Administration regulations, your vehicle has a certification label affixed to the driver’s side door or pillar. This label contains the month and year of manufacture, Gross Vehicle Weight Rating (GVWR), Gross Axle Weight Rating (GAWR) front and rear, and Vehicle Identification Number (VIN). A Month-Day-Hour (MDH) number is included on this label and indicates the Month, Day and Hour of manufacture.
288 STARTING AND OPERATING Tire Size The tire size on the Label represents the actual tire size on your vehicle. Replacement tires must be equal to the load capacity of this tire size. Loading The actual total weight and the weight of the front and rear of your vehicle at the ground can best be determined by weighing it when it is loaded and ready for operation. Rim Size This is the rim size that is appropriate for the tire size listed.
STARTING AND OPERATING 289 Improper weight distributions can have an adverse effect on the way your vehicle steers and handles and the way the brakes operate. To maintain warranty coverage, follow the requirements and recommendations in this manual concerning vehicles used for trailer towing.
290 STARTING AND OPERATING measure GTW is to put your fully loaded trailer on a vehicle scale. The entire weight of the trailer must be supported by the scale. Gross Combination Weight Rating (GCWR) The GCWR is the total permissible weight of your vehicle and trailer when weighed in combination. (Note that GCWR ratings include a 150 lbs (68 kg) allowance for the presence of a driver). Gross Axle Weight Rating (GAWR) The GAWR is the maximum capacity of the front and rear axles.
STARTING AND OPERATING 291 Trailer Sway Control The trailer sway control is a telescoping link that can be installed between the hitch receiver and the trailer tongue that typically provides adjustable friction associated with the telescoping motion to dampen any unwanted trailer swaying motions while traveling. Weight-Carrying Hitch A weight-carrying hitch supports the trailer tongue weight, just as if it were luggage located at a hitch ball or some other connecting point of the truck.
292 STARTING AND OPERATING Weight-distributing systems may not be compatible with surge brake couplers. Consult with your hitch and trailer manufacturer or an authorized recreational vehicle dealer for additional information. Fifth-Wheel Hitch The fifth-wheel hitch is a special high platform with a coupling that mounts over the rear axle of the tow vehicle in the truck bed. It connects a vehicle and fifth-wheel trailer with a coupling king pin.
STARTING AND OPERATING 293 Trailer Hitch Classification Class Max. GTW (Gross Trailer Wt.) Class I - Light Duty 2,000 lbs (907 kg) Class II - Medium 3,500 lbs (1587 kg) Duty Class III - Heavy Duty 5,000 lbs (2268 kg) Class IV - Extra 10,000 lbs (4540 kg) Heavy Duty Fifth Wheel/ Greater than 10,000 lbs Gooseneck (4540 kg) Refer to the “Trailer Towing Weights (Maximum Trailer Weight Ratings)” chart for the Maximum Gross Trailer Weight (GTW) towable for your given drivetrain.
294 STARTING AND OPERATING Trailer and Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% to 15% of the Gross Trailer Weight (GTW) on the tow hitch of your vehicle. Loads balanced over the wheels or heavier in the rear can cause the trailer to sway severely side to side which will cause loss of control of vehicle and trailer. Failure to load trailers heavier in front is the cause of many trailer accidents.
STARTING AND OPERATING 295 NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options, or authorized dealer-installed options must be considered as part of the total load on your vehicle. Refer to “Tire and Loading Information placard” under “Tire Safety Information” in Section 5.
296 STARTING AND OPERATING • When hauling cargo or towing a trailer, do not overload your vehicle or trailer. Overloading can cause a loss of control, poor performance or damage to brakes, axle, engine, transmission, steering, suspension, chassis structure or tires. • Safety chains must always be used between your vehicle and trailer. Always connect the chains to the frame or hook retainers of the vehicle hitch. Cross the chains under the trailer tongue and allow enough slack for turning corners.
STARTING AND OPERATING 297 − Also, check the trailer tires for proper tire inflation pressures before trailer usage. − Check for signs of tire wear or visible tire damage before towing a trailer. Refer to “Tires–General Information” in this section. − When replacing tires, refer to “Tires–General Information” in this section. Replacing tires with a higher load carrying capacity will not increase the vehicle’s GVWR and GAWR limits.
298 STARTING AND OPERATING WARNING! • Do not connect trailer brakes to your vehicle’s hydraulic brake lines. It can overload your brake system and cause it to fail. You might not have brakes when you need them and could have an accident. • Towing any trailer will increase your stopping distance. When towing you should allow for additional space between your vehicle and the vehicle in front of you. Failure to do so could result in an accident.
STARTING AND OPERATING 299 The following chart identifies the maximum electrical loads that the trailer tow output circuits are capable of supporting. Trailer Tow Additional Lamp Loads Output Maximum Additional Bulbs AlFunctions Current lowed. Example Only. Other bulb combinations can be used as long as maximum current is not exceeded.
300 STARTING AND OPERATING NOTE: Check the automatic transmission fluid level before towing. Towing Tips — Tow/Haul (If Equipped) To reduce potential for automatic transmission overheating, turn the “TOW HAUL OD/OFF” feature ON when driving in hilly areas or shift the transmission to Drive position 2 on more severe grades. Towing Tips — Electronic Speed Control (If Equipped) − Do not use in hilly terrain or with heavy loads.
STARTING AND OPERATING 301 Dodge Body Builders Guide. See your authorized dealer, installer or snowplow manufacturer for this information. There are unique electrical systems that must be connected to properly assure operator safety and prevent overloading vehicle systems. WARNING! Attaching a snowplow to this vehicle could adversely affect performance of the airbag system in an accident.
302 STARTING AND OPERATING Snowplow Prep Package Model Availability For Information about snowplow applications visit www.dodge.com or refer to the current Dodge Body Builders Guide. 1. The maximum number of occupants in the truck should not exceed two. 2. The total GVWR or the Front GAWR or the Rear GAWR should never be exceeded. 3. The snowplow prep packages are not available with the Sport Package. 4. Cargo capacity will be reduced by the addition of options or passengers, etc.
STARTING AND OPERATING 303 Over the Road Operation With Snowplow Attached The blade restricts air flow to the radiator and causes the engine to operate at higher than normal temperatures. Therefore, when transporting the plow, angle the blade completely and position it as low as road or surface conditions permit. Do not exceed 40 mph (64 km/h). The operator should always maintain a safe stopping distance and allow adequate passing clearance.
304 STARTING AND OPERATING • Operate with transfer case in 4L when plowing small or congested areas where speeds are not likely to exceed 15 mph (24 km/h). At higher speeds operate in 4H. • Vehicles with automatic transmissions should use 4L range when plowing deep or heavy snow for extended periods of time to avoid transmission overheating. • Do not shift the transmission unless the engine has returned to idle and wheels have stopped.
STARTING AND OPERATING 305 Recreational Towing – 4-Wheel Drive Models CAUTION! Failure to follow these requirements can cause severe damage to the transmission and/or transfer case. NOTE: Both the manual shift and electronic shift transfer cases must be shifted into NEUTRAL for recreational towing. Automatic transmissions must be shifted into the PARK position for recreational towing. Refer to the following for the proper transfer case NEUTRAL shifting procedure for your vehicle.
306 STARTING AND OPERATING 9. Repeat steps 7 and 8 with the transmission in DRIVE. 10. Shut OFF the engine and place the ignition key in the unlocked OFF position. 11. Shift transmission into PARK. 12. Apply the parking brake. 13. Attach vehicle to tow vehicle with tow bar. 14. Release the parking brake. CAUTION! Damage to the transmission may occur if the transmission is shifted into PARK with the transfer case in NEUTRAL and the engine running.
STARTING AND OPERATING 307 WARNING! CAUTION! (Continued) You or others could be injured if you leave the vehicle unattended with the transfer case in the NEUTRAL position without first fully engaging the parking brake. The transfer case NEUTRAL position disengages both the front and rear driveshafts from the powertrain and will allow the vehicle to move, regardless of the transmission position. The parking brake should always be applied when the driver is not in the vehicle.
308 STARTING AND OPERATING 3. Turn the ignition key to the ON position, but do not start the engine. 12. Shut engine OFF and place ignition key in the unlocked OFF position. 4. Depress the brake pedal. 13. Shift transmission into PARK. 5. Shift transmission into NEUTRAL. 14. Apply parking brake. 6. Using the point of a ballpoint pen or similar object, depress the recessed transfer case NEUTRAL button for four seconds. 15. Attach vehicle to tow vehicle with tow bar. 7.
STARTING AND OPERATING 309 • The ignition key must be ON for a shift to take place and for the position indicator lights to be operable. If the key in not ON, the shift will not take place and no position indicator lights will be on or flashing. • Flashing NEUTRAL position indicator light indicates that shift requirements have not been met. CAUTION! Damage to the transmission may occur if the transmission is shifted into PARK with the transfer case in NEUTRAL and the engine running.
310 STARTING AND OPERATING NOTE: • The transfer case cannot be shifted into NEUTRAL from the 4AUTO (if equipped) position. • Flashing Neutral position indicator light indicates that shift requirements have not been met. • Steps 1 through 5 are requirements that must be met prior to depressing the transfer case Neutral (N) button, and must continue to be met until one second elapses and the shift has been completed.
STARTING AND OPERATING 311 CAUTION! • Do not use a bumper-mounted clamp-on tow bar on your vehicle. The bumper face bar will be damaged. • Do not disconnect the rear driveshaft because fluid will leak from the transfer case and fluid loss will damage internal parts.
WHAT TO DO IN EMERGENCIES CONTENTS 䡵 Hazard Warning Flasher . . . . . . . . . . . . . . . . 314 䡵 Jump Starting . . . . . . . . . . . . . . . . . . . . . . . . 326 䡵 Jacking And Tire Changing . . . . . . . . . . . . . . . 315 ▫ With Portable Starting Unit . . . . . . . . . . . . . 330 ▫ 3500 Models — If Equipped . . . . . . . . . . . . . 315 䡵 Freeing A Stuck Vehicle . . . . . . . . . . . . . . . . . 330 ▫ Preparations For Jacking . . . . . . . . . . . . . . .
314 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER The Hazard Warning flasher switch is mounted on the top of the steering column. Press the button on the top of the steering column to turn on the Hazard Warning flasher. When the Hazard Warning flasher is activated, all directional turn signals will flash off and on to warn oncoming traffic of an emergency. Press the button a second time to turn off the flashers. This is an emergency warning system and should not be used when the vehicle is in motion.
WHAT TO DO IN EMERGENCIES 315 JACKING AND TIRE CHANGING WARNING! • Being under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never put any part of your body under a vehicle that is on a jack. Never start or run the engine while the vehicle is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift. • The jack is designed to use as a tool for changing tires only.
316 WHAT TO DO IN EMERGENCIES WARNING! After using the jack and tools, always reinstall them in the original carrier and location. While driving you may experience abrupt stopping, rapid acceleration, or sharp turns. A loose jack, tools, bracket or other objects in the vehicle may move around with force, resulting in serious injury. 4500/5500 Models These vehicles do not come equipped with a jack.
WHAT TO DO IN EMERGENCIES 317 6. Block both the front and rear of the wheel diagonally opposite the jacking position. For example, if the right front wheel is being changed, block the left rear wheel. NOTE: Passengers should not remain in the vehicle when the vehicle is being jacked.
318 WHAT TO DO IN EMERGENCIES WARNING! (Continued) • If working on or near a roadway, be extremely careful of motor traffic. • To assure that spare tires, flat or inflated are securely stowed, spares must be stowed with the valve stem facing the ground. • Turn on the Hazard Warning Flasher. Jack Warning Label 1. If equipped, remove the spare wheel, jack, and tools from storage. 2.
WHAT TO DO IN EMERGENCIES 319 6 Front Jacking Locations Rear Jacking Location When changing a rear wheel, assemble the jack drive tube to the jack and connect the drive tube to the extension tube. Securely place the jack under the sway bar bracket (unless both tires are flat on one side, then place jack under shock bracket) facing forward in vehicle. Connect the jack tube extension and lug wrench.
320 WHAT TO DO IN EMERGENCIES 4. By rotating the wheel wrench clockwise, raise the vehicle until the wheel just clears the surface. WARNING! Raising the vehicle higher than necessary can make the vehicle unstable and cause an accident. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 5. Remove the wheel nuts and pull the wheel off.
WHAT TO DO IN EMERGENCIES 321 7. Install wheel center cap (if equipped) and remove wheel blocks. Do not install chrome or aluminum wheel center caps on the spare wheel. This may result in cap damage. For single rear wheel (SRW) models, use the blade on the end of the lug wrench to pry the hub cap off. Insert the blade end into the pry off notch and carefully pop off the hub cap with a back and forth motion. 8. Lower the jack to its fully closed position.
322 WHAT TO DO IN EMERGENCIES CAUTION! • Use a back and forth motion to remove the hub cap. Do not use a twisting motion when removing the hub cap, damage to the hub cap; finish may occur. • The rear hub caps on the dual rear wheel has two pry off notches. Make sure that the hook of the jack handle driver is located squarely in the cap notch before attempting to pull off. You must use the flat end of the lug wrench to pry off the wheel skins.
WHAT TO DO IN EMERGENCIES 323 Dual wheel models require a special heavy-duty lug nut tightening adapter (included with the vehicle) to correctly tighten the lug nuts. Also, when it is necessary to remove and install dual rear wheels, use a proper vehicle lifting device. NOTE: When installing a spare tire (if equipped) as part of a dual rear wheel end combination, the tire diameter of the two individual tires must be compared.
324 WHAT TO DO IN EMERGENCIES These dual rear wheels should be tightened as follows: Tightening Pattern (10 Studs) Tightening Pattern (8 Studs) 1. Tighten the wheel nuts in the numbered sequence to a snug fit. 2. Retighten the wheel nuts in the same sequence to the torques listed in the table.
WHAT TO DO IN EMERGENCIES 325 second time to verify that specific torque has been achieved. Retighten to specifications at 100 miles (160 km) and after 500 miles (800 km). It is recommended that wheel stud nuts be kept torqued to specifications at all times. Torque wheel stud nuts to specifications at each lubrication interval.
326 WHAT TO DO IN EMERGENCIES To Stow The Flat Or Spare — If Equipped Refer to Upfitters Body Builders Guide for information on stowing your spare tire (if equipped). JUMP STARTING WARNING! HOISTING A conventional floor jack may be used at the jacking locations. Refer to the graphics that show jacking locations. However, a floor jack or frame hoist must never be used on any other parts or the underbody.
WHAT TO DO IN EMERGENCIES 327 Your vehicle is equipped with two 12-Volt batteries. If it becomes necessary to use a booster battery with jumper cables to start a vehicle’s engine because its batteries are discharged, the following procedure should be used: Set the parking brake and place the transmission in PARK. Turn off lights, heater and other electrical loads. Observe charge indicator (if equipped) in both batteries.
328 WHAT TO DO IN EMERGENCIES WARNING! Do not permit vehicles to touch each other as this could establish a ground connection and personal injury could result. Attaching Booster Cables 1 — Discharged Battery 2 — Booster Battery 2. Connect one end of the other jumper cable to negative (-) post of booster battery.
WHAT TO DO IN EMERGENCIES 329 vehicle with the discharged battery. Make sure a good connection is made, free of dirt and grease. WARNING! • Do not connect the cable to the negative post of the discharge battery. The resulting electrical spark could cause the battery to explode. • During cold weather when temperatures are below freezing point, electrolyte in a discharged battery may freeze. Do not attempt jump-starting because the battery could rupture or explode.
330 WHAT TO DO IN EMERGENCIES With Portable Starting Unit There are many types of these units available. Follow the manufacturer’s instructions for necessary precautions and operation. CAUTION! It is very important that the starting unit operating voltage does not exceed 12-Volts DC or damage to battery, starter motor, alternator, or electrical system may occur. FREEING A STUCK VEHICLE If the vehicle becomes stuck in snow, sand, or mud, it can often be moved by a rocking motion.
WHAT TO DO IN EMERGENCIES 331 WARNING! • Chains are not recommended for freeing a stuck vehicle. Chains may break, causing serious injury or death. • Stand clear of vehicles when pulling with tow hooks. Tow straps and chains may break, causing serious injury. CAUTION! Tow hooks are for emergency use only to rescue a vehicle stranded off-road. Do not use tow hooks for tow truck hookup or highway towing. You could damage your vehicle.
332 WHAT TO DO IN EMERGENCIES NOTE: The transfer case must be in the neutral position, and the transmission must be in PARK (automatic transmission), or in gear (manual transmission) to tow a 4-Wheel Drive vehicle with one end of the vehicle raised. The manufacturer recommends towing with all wheels OFF the ground. Acceptable methods are to tow the vehicle on a flatbed or with one end of vehicle raised and the opposite end on a towing dolly.
MAINTAINING YOUR VEHICLE CONTENTS 䡵 Engine Compartment— 5.7L . . . . . . . . . . . . . . 335 ▫ Air Conditioner Maintenance . . . . . . . . . . . . 342 䡵 Onboard Diagnostic System (OBD II) . . . . . . . 336 ▫ Body Lubrication . . . . . . . . . . . . . . . . . . . . 343 ▫ Loose Fuel Filler Cap Message . . . . . . . . . . . 336 ▫ Windshield Wiper Blades . . . . . . . . . . . . . . . 344 䡵 Replacement Parts . . . . . . . . . . . . . . . . . . . . . 337 ▫ Adding Washer Fluid . . . . . . . . . . . . . . .
334 MAINTAINING YOUR VEHICLE ▫ Transfer Case — If Equipped . . . . . . . . . . . . 356 䡵 Bulb Replacement . . . . . . . . . . . . . . . . . . . . . 370 ▫ Automatic Transmission . . . . . . . . . . . . . . . 356 ▫ Headlight (Halogen)/Front Park And Turn Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . 370 ▫ Appearance Care And Protection From Corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . 359 ▫ Fog Lights . . . . . . . . . . . . . . . . . . . . . . . . . 374 䡵 Fuses . . .
MAINTAINING YOUR VEHICLE 335 ENGINE COMPARTMENT— 5.
336 MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM (OBD II) Vehicles with 5.7L engines are equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
MAINTAINING YOUR VEHICLE 337 appear the next time the vehicle is started. This might indicate a damaged cap. If the problem is detected twice in a row, the system will turn on the Malfunction Indicator Light (MIL). Resolving the problem will turn the MIL light off. REPLACEMENT PARTS Use of genuine MOPAR威 parts for normal/scheduled maintenance and repairs is highly recommended to ensure the designed performance.
338 MAINTAINING YOUR VEHICLE MAINTENANCE PROCEDURES The pages that follow contain the required maintenance services determined by the engineers who designed your vehicle. Besides the maintenance items for which there are fixed maintenance intervals, there are other items that should operate satisfactorily without periodic maintenance. However, if a malfunction of these items does occur, it could adversely affect the engine or vehicle performance.
MAINTAINING YOUR VEHICLE 339 Change Engine Oil Refer to the “Maintenance Schedule” in Section 8 for the proper maintenance intervals. Engine Oil Selection For best performance and maximum protection under all types of operating conditions, the manufacturer only recommends engine oils that are API certified and meet the requirements of Chrysler Material Standard MS-6395.
340 MAINTAINING YOUR VEHICLE Synthetic Engine Oils You may use synthetic engine oils provided the recommended oil quality requirements are met, and the recommended maintenance intervals for oil and filter changes are followed. Materials Added to Engine Oil Do not add supplemental materials, other than leak detection dyes, to your engine oil. Engine oil is an engineered product and its performance may be impaired by supplemental additives.
MAINTAINING YOUR VEHICLE 341 WARNING! The air induction system (air cleaner, hoses, etc) can provide a measure of protection in the case of engine backfire. Do not remove the air induction system (air cleaner, hoses, etc) unless such removal is necessary for repair or maintenance. Make sure that no one is near the engine compartment before starting the vehicle with the air induction system (air cleaner, hoses, etc) removed. Failure to do so can result in serious personal injury.
342 MAINTAINING YOUR VEHICLE WARNING! (Continued) • Battery posts, terminals and related accessories contain lead and lead compounds. Wash hands after handling. CAUTION! • It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked (+) positive and negative (-) and identified on the battery case.
MAINTAINING YOUR VEHICLE 343 WARNING! (Continued) • The air conditioning system contains refrigerant under high pressure. To avoid risk of personal injury or damage to the system, adding refrigerant or any repair requiring lines to be disconnected should be done by an experienced repair person. NOTE: Use only manufacturer approved A/C System Sealers, Stop Leak Products, Seal Conditioners, Compressor Oil, or Refrigerants.
344 MAINTAINING YOUR VEHICLE Windshield Wiper Blades Clean the rubber edges of the wiper blades and the windshield periodically with a sponge or soft cloth and a mild nonabrasive cleaner. This will remove accumulations of salt or road film. Operation of the wipers on dry glass for long periods may cause deterioration of the wiper blades. Always use washer fluid when using the wipers to remove salt or dirt from a dry windshield. Avoid using the wiper blades to remove frost or ice from the windshield.
MAINTAINING YOUR VEHICLE 345 WARNING! Commercially available windshield washer solvents are flammable. They could ignite and burn you. Care must be exercised when filling or working around the washer solution. After the engine has warmed, operate the defroster for a few minutes to reduce the possibility of smearing or freezing the fluid on the cold windshield.
346 MAINTAINING YOUR VEHICLE The catalytic converter requires the use of unleaded fuel only. Leaded gasoline will destroy the effectiveness of the catalyst as an emission control device. Under normal operating conditions, the catalytic converter will not require maintenance. However, it is important to keep the engine properly tuned to assure proper catalyst operation and prevent possible catalyst damage.
MAINTAINING YOUR VEHICLE 347 WARNING! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your exhaust system. Do not park or operate your vehicle in areas where your exhaust system can contact anything that can burn. In unusual situations involving grossly malfunctioning engine operation, a scorching odor may indicate severe and abnormal catalyst overheating.
348 MAINTAINING YOUR VEHICLE Cooling System WARNING! You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator. If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool. Never try to open a cooling system pressure cap when the radiator is hot. Engine Coolant Checks Check the engine coolant (antifreeze) protection every 12 months (before the onset of freezing weather, where applicable).
MAINTAINING YOUR VEHICLE 349 Cooling System — Drain, Flush and Refill If the engine coolant (antifreeze) is dirty or contains a considerable amount of sediment, clean and flush with a reliable cooling system cleaner. Follow with a thorough rinsing to remove all deposits and chemicals. Properly dispose of the old engine coolant (antifreeze) solution. Refer to the “Maintenance Schedule” in Section 8 of this manual for the proper maintenance intervals.
350 MAINTAINING YOUR VEHICLE CAUTION! (Continued) • This vehicle has not been designed for use with Propylene Glycol based engine coolant (antifreeze). Use of Propylene Glycol based engine coolant (antifreeze) is not recommended. Adding Coolant Your vehicle has been built with an improved engine coolant (antifreeze) that allows extended maintenance intervals. This engine coolant (antifreeze) can be used up to 5 Years or 102,000 miles (170 000 km) before replacement.
MAINTAINING YOUR VEHICLE 351 NOTE: Mixing engine coolant (antifreeze) types will decrease the life of the engine coolant (antifreeze) and will require more frequent engine coolant (antifreeze) changes. Cooling System Pressure Cap The cap must be fully tightened to prevent loss of engine coolant (antifreeze), and to ensure that engine coolant (antifreeze) will return to the radiator from the coolant recovery bottle.
352 MAINTAINING YOUR VEHICLE Disposal of Used Engine Coolant Used ethylene glycol based engine coolant (antifreeze) is a regulated substance requiring proper disposal. Check with your local authorities to determine the disposal rules for your community. To prevent ingestion by animals or children, do not store ethylene glycol based engine coolant (antifreeze) in open containers or allow it to remain in puddles on the ground. If ingested by a child, contact a physician immediately.
MAINTAINING YOUR VEHICLE 353 If an examination of your engine compartment shows no evidence of radiator or hose leaks, the vehicle may be safely driven. The vapor will soon dissipate. • Do not overfill the coolant recovery bottle. • Check engine coolant (antifreeze) freeze point in the radiator and in the coolant recovery bottle. If engine coolant (antifreeze) needs to be added, contents of coolant recovery bottle must also be protected against freezing.
354 MAINTAINING YOUR VEHICLE The brake master cylinder has a translucent plastic reservoir. On the outboard side of the reservoir, there is a “MAX” mark and an “MIN” mark (4500/5500 vehicles only). The fluid level must be kept within these two marks. Do not add fluid above the full mark because leakage may occur at the cap. With disc brakes, the fluid level can be expected to fall as the brake linings wear.
MAINTAINING YOUR VEHICLE 355 Rear Axle And 4x4 Front Driving Axle Fluid Level For models with 9.25 in Front Axles and 11.5 in Rear Axles, refer to “Fluids, Lubricants, and Genuine Parts” in this section for the correct fluid type. For normal service, periodic fluid level checks are not required. When the vehicle is serviced for other reasons, the exterior surfaces of the axle assembly should be inspected. When checking the fluid level (4500/5500 only), the vehicle should be in a level position.
356 MAINTAINING YOUR VEHICLE Lubricant Selection Refer to “Fluids, Lubricants, and Genuine Parts” in this section for the correct fluid type. NOTE: The presence of water in the gear lubricant will result in corrosion and possible failure of differential components. Operation of the vehicle in water, as may be encountered in some off-highway types of service, will require draining and refilling the axle to avoid damage.
MAINTAINING YOUR VEHICLE 357 Parts” in this section for the correct fluid type. It is important that the transmission fluid be maintained at the prescribed level using the recommended fluid. CAUTION! Using a transmission fluid other than the manufacturer’s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder. Using a transmission fluid other than the manufacturer’s recommended fluid will result in more frequent fluid and filter changes.
358 MAINTAINING YOUR VEHICLE 6. Remove the dipstick again and note the fluid level on both sides. The fluid level should be between the HOT (upper) reference holes on the dipstick at normal operating temperature. Verify that a solid coating of oil is seen on both sides of the dipstick. If the fluid is low, add as required into the dipstick tube. Do not overfill.
MAINTAINING YOUR VEHICLE 359 NOTE: If the transmission is disassembled for any reason, the fluid and filter should be changed. It is important that proper lubricant is used in the transmission. Refer to “Fluids, Lubricants, and Genuine Parts” in this section for the correct fluid type. Special Additives Automatic Transmission Fluid (ATF) is an engineered product and its performance may be impaired by supplemental additives. Therefore, do not add any fluid additives to the transmission.
360 MAINTAINING YOUR VEHICLE • Insects, tree sap and tar. • Salt in the air near seacoast localities. • Atmospheric fallout/industrial pollutants. • Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish. CAUTION! Washing • Wash your vehicle regularly. Always wash your vehicle in the shade using MOPAR威 Car Wash or a mild car wash soap, and rinse the panels completely with clear water.
MAINTAINING YOUR VEHICLE 361 • If you detect any stone chips or scratches in the paint, touch them up immediately. The cost of such repairs is considered the responsibility of the owner. • If your vehicle is damaged due to an accident or similar cause which destroys the paint and protective coating, have your vehicle repaired as soon as possible. The cost of such repairs is considered the responsibility of the owner. • If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc.
362 MAINTAINING YOUR VEHICLE • Blot any remaining stain with a clean, damp towel. • For tough stains, apply MOPAR威 Total Clean or a mild soap solution to a clean, damp cloth and remove stain. Use a fresh, damp towel to remove soap residue. • For grease stains, apply MOPAR威 Multi-Purpose Cleaner to a clean, damp cloth and remove stain. Use a fresh, damp towel to remove soap residue. • Do not use any solvents or protectants on YES Essentials威 products.
MAINTAINING YOUR VEHICLE 363 Cleaning Headlights Your vehicle has plastic headlights that are lighter and less susceptible to stone breakage than glass headlights. Plastic is not as scratch resistant as glass and therefore different lens cleaning procedures must be followed. To minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. To remove road dirt, wash with a mild soap solution followed by rinsing.
364 MAINTAINING YOUR VEHICLE Seat Belt Maintenance Do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage can also weaken the fabric. and component may be stamped on the inside cover, otherwise the cavity number of each fuse is stamped on the inside cover that corresponds to the following chart. If the belts need cleaning, use a mild soap solution or lukewarm water. Do not remove the belts from the vehicle to wash them.
MAINTAINING YOUR VEHICLE 365 Cavity Cartridge Mini Fuse Fuse 1 20 Amp Yellow 2 20 Amp Yellow 3 4 5 6 7 8 — 15 Amp Blue 20 Amp Yellow 10 Amp Red — 10 Amp Red Description Power Outlet Console Cabin Compartment Node (CCN) Door Locks — Aisin Transmission Controls (Diesel Only) Power Sunroof Vistronic Fan/ Wastegate Solenoid — Heated Mirrors Cavity Cartridge Mini Fuse Fuse 9 30 Amp Pink 10 5 Amp Orange 11 20 Amp Yellow Description Off Road Module Power Trx-Off Rd Pkg Sen (Gas Engine Only) NOTE: Insert 5 a
366 MAINTAINING YOUR VEHICLE Cavity Cartridge Mini Fuse Fuse 12 30 Amp Pink 13 25 Amp Natural 14 15 Amp Blue 20 Amp Yellow 15 Amp Blue — 15 16 17 18 19 40 Amp Green 30 Amp Pink Description Electric Brake Power-Battery RWAL/ABS Module Feed Park Lights Left Trailer Park Lights Park Lights Right — ABS Pump Trailer Tow Battery Feed Cavity Cartridge Mini Fuse Fuse 20 10 Amp Red 21 10 Amp Red 22 2 Amp Gray 23 10 Amp Red 24 20 Amp Blue 25 10 Amp Red 26 20 Amp Yellow Description Occupant Restraints Controlle
MAINTAINING YOUR VEHICLE 367 Cavity Cartridge Mini Fuse Fuse 27 40 Amp Green 28 10 Amp Red 29 30 31 10 Amp Red 15 Amp Blue 10 Amp Red Description Power Seats Power Run/StartPCM/Steering Angle Sensor 4X4 Switch/Pass Dr Switch/EC Mirror Power Run/StartABS/RWAL/Smart Bar/YAW Sensor/ Universal Exhaust Gas Oxygen (Uego) Sensor Controller PCM (Gas)/TCM (Diesel 58RFE) Cavity Cartridge Mini Fuse Fuse 32 10 Amp Red 33 34 35 36 37 38 10 Amp Red — 15 Amp Blue 25 Amp Natural 15 Amp Blue 20 Amp Yellow Descript
368 MAINTAINING YOUR VEHICLE Cavity Cartridge Mini Fuse Fuse 39 10 Amp Red 40 20 Amp Yellow 41 42 — 30 Amp Pink Description Seatbelt Tension Reducer/Power IGN Run/Acc Power IGN Run/Acc — Cigar Lighter/Rear Power Point — Diesel PCM (Diesel Only) CAUTION! • When installing the Integrated Power Module cover, it is important to ensure the cover is properly positioned and fully latched.
MAINTAINING YOUR VEHICLE 369 VEHICLE STORAGE If you are storing your vehicle for more than 21 days, we recommend that you take the following steps to minimize the drain on your vehicle’s battery: in the fresh air and high blower setting. This will ensure adequate system lubrication to minimize the possibility of compressor damage when the system is started again. • Disconnect the Ignition-Off Draw (IOD) fuse located in the Integrated Power Module, located in the engine compartment.
370 MAINTAINING YOUR VEHICLE REPLACEMENT LIGHT BULBS BULB REPLACEMENT LIGHT BULBS — Inside Bulb No. Overhead Console Lights . . . . . . . . . . . . . . . TS 212-2 Dome Light. . . . . . . . . . . . . . . . . . . . . . . . . . . . 7679 NOTE: For lighted switches, see your authorized dealer for replacement instructions. All of the inside bulbs are brass or glass-wedge base. Aluminum base bulbs are not approved. LIGHT BULBS — Exterior Bulb No. Backup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 371 1. Open the hood. 3. Remove the plug from the inner fender well. 2. Remove the two bolts from the front of the headlight housing.
372 MAINTAINING YOUR VEHICLE 4. Remove the nut through the access hole. 5. Pull the housing out from the fender to allow room to disconnect the electrical connectors. NOTE: For easier removal, pull the headlight assembly straight forward, applying the greatest amount of force to the outer edge of the headlight assembly.
MAINTAINING YOUR VEHICLE 373 6. Unlock and pull connector straight from the base of the headlight halogen bulb. 7. Twist connector on the side marker/turn signal/park light bulb 1⁄4 turn and remove connector and bulb from housing. 8. Remove housing from vehicle with headlight halogen bulb in housing. 9. Twist the headlight halogen bulb 1⁄4 turn and remove headlight bulb from the housing. 10. Replace headlight or side marker/turn signal/park light bulb. Do not touch the headlight halogen bulb. 11.
374 MAINTAINING YOUR VEHICLE Fog Lights 1. Reach under the vehicle, unlock and twist connector counterclockwise 1⁄4 turn and remove connector and bulb from housing. 3. Reverse procedure for installation of bulbs and housing. 2. Pull bulb straight from the connector.
MAINTAINING YOUR VEHICLE 375 Cab Top Clearance Lights — If Equipped 1. Remove the two screws from the top of the light. 2. Rotate the socket 1⁄4 turn and pull it from the light assembly.
376 MAINTAINING YOUR VEHICLE 3. Pull the bulb straight from its socket and replace.
MAINTAINING YOUR VEHICLE 377 FLUID AND CAPACITIES Fuel (Approximate) Standard Rear Tank Optional Midship Tank Engine Oil with Filter 5.7L Engine (SAE 5W-20, API Certified) (For vehicles operating under a gross combined weight rating less than 14,000 lbs.) 5.7L Engine (SAE 5W-30, API Certified) (For vehicles operating under a gross combined weight rating greater than 14,000 lbs.) Cooling System 5.7L Engine (MOPAR威 Antifreeze/Coolant 5 Year/100,000 Mile Formula) or equivalent. U.S.
378 MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant Engine Oil (5.7L Engine) (For vehicles operating under a gross combined weight rating less than 14,000 lbs.) Engine Oil (5.7L Engine) (For vehicles operating under a gross combined weight rating greater than 14,000 lbs.) Engine Oil Filter (5.7L Engine) Spark Plugs (5.7L Engine) Fuel Selection (5.
MAINTAINING YOUR VEHICLE 379 Chassis Component Automatic Transmission (5-Speed 545RFE) Transfer Case Front and Rear Axle Fluid (4500/ 5500) Brake Master Cylinder Power Steering Reservoir Fluid, Lubricant, or Genuine Part MOPAR威 ATF+4 Automatic Transmission Fluid MOPAR威 ATF+4 Automatic Transmission Fluid GL-5 SAE 75W-90 Synthetic (MS-9763) or equivalent. MOPAR威 DOT 3 and SAE J1703 should be used or equivalent. If DOT 3 brake fluid is not available, then DOT 4 is acceptable.
MAINTENANCE SCHEDULES CONTENTS 䡵 Emissions Control System Maintenance . . . . . . 382 䡵 Maintenance Schedule . . . . . . . . . . . . . . . . . . 382 ▫ 5.7L Gas Engine . . . . . . . . . . . . . . . . . . . . .
M A I N T E N A N C E 382 MAINTENANCE SCHEDULES EMISSIONS CONTROL SYSTEM MAINTENANCE The Scheduled Maintenance services listed in bold type must be done at the times or mileages specified to ensure the continued proper functioning of the emissions control system. These and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
MAINTENANCE SCHEDULES 383 M A • Change your engine oil more often if you drive your vehicle off-road for an extended period of time. • Check the windshield washer solvent and add if I N required. T • Under no circumstances should oil change intervals exceed 6,000 miles (10,000 km) or 6 months, whichever comes first. Once a Month Your dealer will reset the oil change indicator message after completing the scheduled oil change.
M A I N T E N A N C E S C H E D U L E S 8 384 MAINTENANCE SCHEDULES At Each Oil Change • Change the engine oil filter. • Inspect the brake hoses and lines. • Lubricate outer tie rod ends. CAUTION! Failure to perform the required maintenance items may result in damage to the vehicle. Required Maintenance Intervals Refer to the Maintenance Schedules on the following pages for the required maintenance intervals.
MAINTENANCE SCHEDULES 385 M 6,000 Miles (10,000 km) or 6 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ Lube front drive shaft fitting (4x4 only). ❏ Lubricate outer tie rod ends. 12,000 Miles (20,000 km) or 12 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter, replace if necessary.
M 386 MAINTENANCE SCHEDULES A I N 18,000 Miles (30,000 km) or T 18 Months Maintenance E N Service Schedule A ❏ Change the engine oil and engine oil filter. N C ❏ Rotate tires. E ❏ Lube front drive shaft fitting (4x4 only). S C H E D U L E S ❏ Lubricate outer tie rod ends. ❏ Inspect the front & rear axle fluid. Change if using your vehicle for police, taxi, fleet, off-road or frequent trailer towing.
MAINTENANCE SCHEDULES 387 M 30,000 Miles (50,000 km) or 30 Months Maintenance Service Schedule 36,000 Miles (60,000 km) or 36 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ Replace the engine air cleaner filter. ❏ Replace the spark plugs (5.7L engine). ❏ Lube front drive shaft fitting (4x4 only). ❏ Lubricate outer tie rod ends. ❏ Inspect the transfer case fluid. ❏ Change the engine oil and engine oil filter. ❏ Rotate tires.
M 388 MAINTENANCE SCHEDULES A I N 42,000 Miles (70,000 km) or T 42 Months Maintenance E N Service Schedule A ❏ Change the engine oil and engine oil filter. N C ❏ Rotate tires. E ❏ Lube front drive shaft fitting (4x4 only). S C H E D U L E S ❏ Lubricate outer tie rod ends. 48,000 Miles (80,000 km) or 48 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions.
MAINTENANCE SCHEDULES 389 M 54,000 Miles (90,000 km) or 54 Months Maintenance Service Schedule 60,000 Miles (100,000 km) or 60 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ Lube front drive shaft fitting (4x4 only). ❏ Lubricate outer tie rod ends. ❏ Inspect the front & rear axle fluid. Change if using your vehicle for police, taxi, fleet, off-road or frequent trailer towing. ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ Change the engine oil and engine oil filter. Rotate tires.
M 390 MAINTENANCE SCHEDULES A I N 66,000 Miles (110,000 km) or T 66 Months Maintenance E N Service Schedule A ❏ Change the engine oil and engine oil filter. N C ❏ Rotate tires. E ❏ Lube front drive shaft fitting (4x4 only). S C H E D U L E S ❏ Lubricate outer tie rod ends. 72,000 Miles (120,000 km) or 72 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions.
MAINTENANCE SCHEDULES 391 M 78,000 Miles (130,000 km) or 78 Months Maintenance Service Schedule 84,000 Miles (140,000 km) or 84 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ Lube front drive shaft fitting (4x4 only). ❏ Lubricate outer tie rod ends. ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter, replace if necessary.
M 392 MAINTENANCE SCHEDULES A I N 90,000 Miles (150,000 km) or 90 Months Maintenance Service T Schedule E ❏ Change the engine oil and engine oil filter. N A ❏ Rotate tires. N ❏ Replace the engine air cleaner filter. C ❏ Replace the spark plugs (5.7L engine). E ❏ Inspect and replace PCV valve if necessary. † S C H E D U L E S ❏ Lube front drive shaft fitting (4x4 only). ❏ Lubricate outer tie rod ends. ❏ Inspect the front & rear axle fluid.
MAINTENANCE SCHEDULES 393 M 96,000 Miles (160,000 km) or 96 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter, replace if necessary. ❏ Inspect the brake linings, replace if necessary. ❏ Lubricate outer tie rod ends. ❏ Inspect the front suspension, tie rod ends, and boot seals, replace if necessary. ❏ Lube front drive shaft fitting (4x4 only).
M 394 MAINTENANCE SCHEDULES A I N 108,000 Miles (180,000 km) or 108 Months Maintenance Service T Schedule E ❏ Change the engine oil and engine oil filter. N A ❏ Rotate tires. N ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter, replace if necessary. C E ❏ Inspect the brake linings, replace if necessary. S C H E D U L E S ❏ Lube front drive shaft fitting (4x4 only). ❏ Lubricate outer tie rod ends. ❏ Inspect the front & rear axle fluid.
MAINTENANCE SCHEDULES 395 M 120,000 Miles (200,000 km) or 120 Months Maintenance Service Schedule ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ Change the engine oil and engine oil filter. Rotate tires. Replace the engine air cleaner filter. Replace the spark plugs (5.7L engine). Inspect the brake linings, replace if necessary. Lubricate outer tie rod ends. Inspect the front suspension, tie rod ends, and boot seals, replace if necessary. Lube front drive shaft fitting (4x4 only). Inspect the CV Joints. Inspect exhaust system.
M 396 MAINTENANCE SCHEDULES A I N 132,000 Miles (220,000 km) or T 132 Months Maintenance E N Service Schedule A ❏ Change the engine oil and engine oil filter. N C ❏ Rotate tires. E ❏ If using your vehicle for any of the S C H E D U L E S following: Dusty or off-road conditions. Inspect the engine air cleaner filter, replace if necessary. ❏ Inspect the brake linings, replace if necessary. ❏ Lube front drive shaft fitting (4x4 only). ❏ Lubricate outer tie rod ends.
MAINTENANCE SCHEDULES 397 M 144,000 Miles (240,000 km) or 144 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter, replace if necessary. ❏ Inspect the brake linings, replace if necessary. ❏ Lubricate outer tie rod ends. ❏ Inspect the front suspension, tie rod ends, and boot seals, replace if necessary.
M A I N T E N A N C E S C H E D U L E S 8 398 MAINTENANCE SCHEDULES † This maintenance is recommended by the manufacturer to the owner, but is not required to maintain emissions warranty. WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS 䡵 Suggestions For Obtaining Service For Your Vehicle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 401 ▫ Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) . . . . . . . . . . . . 403 ▫ Prepare For The Appointment . . . . . . . . . . . 401 ▫ Service Contract . . . . . . . . . . . . . . . . . . . . . 403 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . 401 䡵 Warranty Information (U.S. Vehicles Only) . . . .
400 IF YOU NEED CONSUMER ASSISTANCE 䡵 Publication Order Forms . . . . . . . . . . . . . . . . 405 ▫ Traction Grades . . . . . . . . . . . . . . . . . . . . . 407 䡵 Department Of Transportation Uniform Tire Quality Grades . . . . . . . . . . . . . . . . . . . . . . . . 406 ▫ Temperature Grades . . . . . . . . . . . . . . . . . . 408 ▫ Treadwear . . . . . . . . . . . . . . . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE 401 SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager. Keep a maintenance log of your vehicle’s service history. This can often provide a clue to the current problem.
402 IF YOU NEED CONSUMER ASSISTANCE This is why you should always talk to an authorized dealer’s service manager first. Most matters can be resolved with this process. • If for some reason you are still not satisfied, talk to the general manager or owner of the authorized dealership. They want to know if you need assistance. • If an authorized dealership is unable to resolve the concern, you may contact the manufacturer’s customer center.
IF YOU NEED CONSUMER ASSISTANCE 403 Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommunication Devices for the Deaf) equipment at its customer center. Any hearing or speech impaired customer, who has access to a TDD or a conventional teletypewriter (TTY) in the United States, can communicate with the manufacturer by dialing 1–800–380–CHRY.
404 IF YOU NEED CONSUMER ASSISTANCE WARNING! Engine exhaust, some of its constituents, and certain vehicle components contain, or emit, chemicals known to the State of California to cause cancer and birth defects, or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain, or emit, chemicals known to the State of California to cause cancer and birth defects, or other reproductive harm. WARRANTY INFORMATION (U.S.
IF YOU NEED CONSUMER ASSISTANCE 405 To contact NHTSA, you may either call the Auto Safety Hotline toll free at 1–888–327–4236 (TTY: 1–800–424– 9153), or go to http://www.safercar.gov; or write to: Administrator, NHTSA, 400 Seventh Street, SW., Washington, D.C. 20590. You can also obtain other information about motor vehicle safety from http://www.safercar.gov. In Canada If you believe that your vehicle has a safety defect, you should contact the Customer Service Department immediately.
406 IF YOU NEED CONSUMER ASSISTANCE • Diagnostic Procedure Manuals Diagnostic Procedure Manuals are filled with diagrams, charts and detailed illustrations. These practical manuals make it easy for students and technicians to find and fix problems on computer-controlled vehicle systems and features. They show exactly how to find and correct problems the first time, using step-bystep troubleshooting and drivability procedures, proven diagnostic tests and a complete list of all tools and equipment.
IF YOU NEED CONSUMER ASSISTANCE 407 Treadwear The Treadwear grade is a comparative rating, based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half times as well on the government course as a tire graded 100.
408 IF YOU NEED CONSUMER ASSISTANCE Temperature Grades The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
INDEX 10
410 INDEX Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 285 Adjustable Pedals . . . . . . . . . . . . . . . . . . . . . . . 131 Air Cleaner, Engine (Engine Air Cleaner Filter) . . . 340 Air Conditioner Maintenance . . . . . . . . . . . . . . . 342 Air Conditioning Refrigerant . . . . . . . . . . . . . 342,343 Air Conditioning System . . . . . . . . . . . . . . . . 207,342 Air Conditioning System, Zone Control . . . . . . . . 210 Air Pressure, Tires . . . . . . . . . . . . . . . . . . .
INDEX 411 Emergency Starting . . . . . . . . . . . . . . . . . . . . . 326 Saving Feature (Protection) . . . . . . . . . . . . . . . 124 Belts, Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Body Builders Guide . . . . . . . . . . . . . . . . . . . . . . . 6 Body Mechanism Lubrication . . . . . . . . . . . . . . . 343 B-Pillar Location . . . . . . . . . . . . . . . . . . . . . . . . 262 Brake Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . 379 Brake System . . . . . . . .
412 INDEX Cleaning Wheels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 361 Climate Control . . . . . . . . . . . . . . . . . . . . . . . . . 204 Clock . . . . . . . . . . . . . . . . . . . . . . . . 172,175,189,195 Compact Disc (CD) Maintenance . . . . . . . . . . . . . 203 Compass . . . . . . . . . . . . . . . . . . . . . . . . . . . 140,141 Compass Calibration . . . . . . . . . . . . . . . . . . . . . 141 Compass Variance . . . . . . . . . . . . . . . . . . . . . . .
INDEX 413 Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Driving Through Flowing, Rising, or Shallow Standing Water . . . . . . . . . . . . . . . . . . . . . . . . 250 Dual Rear Wheels . . . . . . . . . . . . . . . . . . . . . 280,322 DVD Player (Video Entertainment System™) . . . . 201 Electric Rear Window Defrost . . . . . . . . . . . . . . . 153 Electrical Power Outlets . . . . . . . . . . . . . . . . . . . 144 Electronic Speed Control (Cruise Control) . . . . . .
414 INDEX Fabric Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . 361 Filters Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . 340 Engine Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . 378 Engine Oil . . . . . . . . . . . . . . . . . . . . . 338,340,378 Flashers Turn Signal . . . . . . . . . . . . . . . . . . . . . . . . . . 127 Flat Tire Stowage . . . . . . . . . . . . . . . . . . . . . . . . 326 Flooded Engine Starting . . . . . . . . . . . . . . . . . . .
INDEX 415 Gauges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162 Coolant Temperature . . . . . . . . . . . . . . . . . . . 164 Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171 Oil Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . 164 Speedometer . . . . . . . . . . . . . . . . . . . . . . . . . 163 Tachometer . . . . . . . . . . . . . . . . . . . . . . . . . . 163 Voltmeter . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162 Gear Ranges . . . . . .
416 INDEX Hitches Trailer Towing Hoisting . . . . . . Hood Release . . Hub Caps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 292 326 121 321 Ignition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Ignition Key Removal . . . . . . . . . . .
INDEX 417 Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75,123 Airbag . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57,163 Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165 Anti-Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . 170 Anti-Lock Warning . . . . . . . . . . . . . . . . . . . . . 257 Brake Warning . . . . . . . . . . . . . . . . . . . . . . . . 168 Bulb Replacement . . . . . . . . . . . . . . . . . . . . . . 370 Cap Top Clearance . . .
418 INDEX Power Door . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Steering Wheel . . . . . . . . . . . . . . . . . . . . . . . . . 14 Lower Anchors and Tether for CHildren (LATCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 Lubrication, Body . . . . . . . . . . . . . . . . . . . . . . . 343 Lug Nuts . . . . . . . . . . . . . . . . . . . . . . . . . . . 320,322 Lumbar Support . . . . . . . . . . . . . . . . . . . . . . . . 118 Electric Powered . . . . . . . . . . . . . . . .
INDEX 419 Change Interval . . . . . . . . . . . . . . . . . . . . . . . 339 Dipstick . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 338 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . 340 Filter . . . . . . . . . . . . . . . . . . . . . . . . . 338,340,378 Identification Logo . . . . . . . . . . . . . . . . . . . . . 339 Materials Added to . . . . . . . . . . . . . . . . . . . . . 340 Pressure Gauge . . . . . . . . . . . . . . . . . . . . . . . 164 Recommendation . . . . . . . .
420 INDEX Power Steering Fluid . . . . . . . . . . . . . . . . . . . . . 379 Pregnant Women and Seat Belts . . . . . . . . . . . . . . 47 Programming Transmitters (Remote Keyless Entry) . . . . . . . . . . . . . . . . . . . . 24 Radial Ply Tires . . . . . . . . . . . . . . . . . . . . . . . . . 272 Radiator Cap (Coolant Pressure Cap) . . . . . . . 348,351 Radio, Navigation . . . . . . . . . . . . . . . . . . . . . . . 194 Radio Operation . . . . . . . . . . . . . . . . . . . . . .
INDEX 421 Safety Checks Outside Vehicle . . . . . . . . . . . . . . . 75 Safety Defects, Reporting . . . . . . . . . . . . . . . . . . 404 Safety Information, Tire . . . . . . . . . . . . . . . . . . . 258 Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 Satellite Radio . . . . . . . . . . . . . . . . . . . . . . . 195,197 Satellite Radio Antenna . . . . . . . . . . . . . . . . . . . 200 Schedule, Maintenance . . . . . . . . . . . . . . . . . . . . 382 Seat Belt Maintenance . . . .
422 INDEX Transfer Case, Shifting into Transfer Case Neutral (N) . . . . . . . . . . . . . . . . . . . . 305,307 Transfer Case, Shifting out of Transfer Case Neutral (N) . . . . . . . . . . . . . . . . . . . . 306,309 Shoulder Belt Upper Anchorage . . . . . . . . . . . . . . 44 Shoulder Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Signals, Turn . . . . . . . . . . . . . . . . . . . . . . . . . . . 127 Sliding Rear Window Power . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 423 Tether Anchor, Child Restraint . . . . . . . . . . . . . 64,67 Tilt Steering Column . . . . . . . . . . . . . . . . . . . . . 130 Tip Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 222 Tire and Loading Information Placard . . . . . . 262,276 Tire Identification Number (TIN) . . . . . . . . . . . . . 261 Tire Markings . . . . . . . . . . . . . . . . . . . . . . . . . . 258 Tire Safety Information . . . . . . . . . . . . . . . . . . . . 258 Tires . . . . . . . . . . . . . . . . .
424 INDEX Traction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 250 Traction Control . . . . . . . . . . . . . . . . . . . . . . . . . 356 Trailer Towing . . . . . . . . . . . . . . . . . . . . . . . . . . 289 Cooling System Tips . . . . . . . . . . . . . . . . . . . . 300 Hitches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 292 Minimum Requirements . . . . . . . . . . . . . . . . . 295 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 425 Warning Lights (Instrument Cluster Description) . . . . . . . . . . . . . 162 Warnings and Cautions . . . . . . . . . . . . . . . . . . . . . 6 Warranty Information . . . . . . . . . . . . . . . . . . . . . 404 Washers, Windshield . . . . . . . . . . . . . . . . . . 130,344 Washing Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . 360 Water Driving Through . . . . . . . . . . . . . . . . . . . . . . 250 Wheel and Wheel Trim . . . . . . . . . . . . . . . . . . . .
INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained personnel. The following must be observed during installation. The positive power connection should be made directly to the battery and fused as close to the battery as possible.
OWNER’S MANUAL Chrysler LLC 81-326-0926 First Edition Printed in U.S.A.
