2011 user guide includes SRT8
The driver’s primary responsibility is the safe operation of the vehicle. Driving while distracted can result in loss of vehicle control, resulting in a collision and personal injury. Chrysler Group LLC strongly recommends that the driver use extreme caution when using any device or feature that may take their attention off the road.
TABLE OF CONTENTS INTRODUCTION/WELCOME UTILITY Welcome From Chrysler Group LLC . . . . 2 Trailer Towing Weights (Maximum Trailer Weight Ratings) . . . . . . . . . . . . . . 46 Recreational Towing (Behind Motorhome, Etc.) . . . . . . . . . . . . . . . . . . . . 47 CONTROLS AT A GLANCE Driver Cockpit . . . . . . . . . . . . . . . 4 Instrument Cluster . . . . . . . . . . . . . 6 WHAT TO DO IN EMERGENCIES GETTING STARTED Key FOB . . . . . . . . . . . . . . . . . Remote Start . . . . . . . . . . . . . . .
INTRODUCTION/WELCOME WELCOME FROM CHRYSLER GROUP LLC Congratulations on selecting your new Chrysler Group LLC vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. Your new Chrysler Group LLC vehicle has characteristics to enhance the driver's control under some driving conditions. These are to assist the driver and are never a substitute for attentive driving. They can never take the driver's place.
INTRODUCTION/WELCOME WARNING! (Continued) • Always make sure that objects cannot fall into the driver foot well while the vehicle is moving. Objects can become trapped under the brake pedal and accelerator pedal causing a loss of vehicle control. • Failure to properly follow floor mat installation or mounting can cause interference with the brake pedal and accelerator pedal operation causing loss of control of the vehicle. • Never use the ‘PARK’ position as a substitute for the parking brake.
CONTROLS AT A GLANCE DRIVER COCKPIT 4
CONTROLS AT A GLANCE 5
CONTROLS AT A GLANCE INSTRUMENT CLUSTER Warning Lights - Low Fuel Warning Light - Charging System Light** - Oil Pressure Warning Light** - Anti-Lock Brake (ABS) Light** - Airbag Warning Light** - Electronic Throttle Control (ETC) Light - Tire Pressure Monitoring System (TPMS) Light - Engine Temperature Warning Light - Seat Belt Reminder Light BRAKE - Brake Warning Light** - Malfunction Indicator Light (MIL)** - Electronic Stability Program (ESP) Indicator Light/Brake Assist System (BAS) Warning Light**
CONTROLS AT A GLANCE Indicators - Turn Signal Indicators - High Beam Indicator - Electronic Stability Program (ESP) Indicator - Front Fog Light Indicator - Windshield Washer Fluid Low Indicator*** - Vehicle Security Indicator* - Door Ajar Indicator*** - Electronic Speed Control / Adaptive Cruise Control (ACC) Indicator Odometer Messages ECO - Fuel Saver Indicator gASCAP - Fuel Cap Fault - Decklid Ajar Indicator*** Lo tirE - Low Tire Pressure noFUSE* - Fuse Fault CHAngE OIL* - Change Engine Oil * I
GETTING STARTED KEY FOB Locking And Unlocking The Doors • Press the LOCK button once to lock all the doors. Press the UNLOCK button once to unlock the driver’s door only and twice within five seconds to unlock all the doors. • All doors can be programmed to unlock on the first press of the UNLOCK button. Refer to Programmable Features in this guide. Opening The Trunk • Press the TRUNK button two times within five seconds to open the trunk.
GETTING STARTED WARNING! (Continued) • Keep Key Fob transmitters away from children. Operation of the Remote Start System, windows, door locks or other controls could cause serious injury or death. REMOTE START • Press the REMOTE START button x2 twice within five seconds. Pressing the REMOTE START button a third time shuts the engine off. • To drive the vehicle, press the UNLOCK button, insert the Key Fob in the ignition and turn to the ON/RUN position.
GETTING STARTED To Lock the Vehicle: • Both front door handles have LOCK buttons located on the outside of the handle. With one of the vehicle's Keyless Enter-N-Go Key Fobs located outside the vehicle and within 5 ft (1.5m) of the driver's or passenger front door handle, press the door handle LOCK button to lock all four doors and trunk. NOTE: • If “Unlock All Doors 1st Press” is programmed all doors will unlock when you grab hold of the front driver's door handle.
GETTING STARTED Engine Starting/Stopping - Automatic Transmission Starting • Place the shift lever in PARK or NEUTRAL. • While pressing the brake pedal, press the ENGINE START/STOP button once. If the engine fails to start, the starter will disengage automatically after 10 seconds. • To stop the cranking of the engine prior to the engine starting, press the button again. Stopping • Place the shift lever in PARK. • Press the ENGINE START/STOP button once. The ignition switch will return to the OFF position.
GETTING STARTED Additional Functions NOTE: The following functions are with the driver’s foot OFF the Brake Pedal/Clutch Pedal (Transmission in PARK or NEUTRAL Position). Starting With The Ignition Switch In The OFF Position: • Press the ENGINE START/STOP button once to change the ignition switch to the ACC position. • Press the ENGINE START/STOP button a second time to change the ignition switch to the RUN position.
GETTING STARTED SEAT BELT • Be sure everyone in your vehicle is in a seat and using a seat belt properly. • Position the lap belt across your thighs, below your abdomen. To remove slack in the lap portion, pull up a bit on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision. • Position the shoulder belt on your chest so that it is comfortable and not resting on your neck.
GETTING STARTED • If the Airbag Warning Light is not on during starting, stays on, or turns on while driving, have the vehicle serviced by an authorized service center immediately. • Refer to the Owner's Manual on the DVD for further details regarding the Supplemental Restraint System (SRS). WARNING! • Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly. In some collisions, the airbags won't deploy at all.
GETTING STARTED • Child seats with flexible or fixed rigid attachments can be installed in all rear seating positions. Child seats can be installed using the LATCH system in either or both outboard seating positions or the center position, but not all three at the same time. If a child seat is installed in an outboard seating position using the lower anchors, then the vehicle seatbelt must be used for the center position.
GETTING STARTED • Route the tether strap to provide the most direct path for the strap between the anchor and the child seat. • Attach the tether strap hook of the child restraint to the anchor and remove slack in the tether strap according to the child restraint manufacturer’s instructions. WARNING! • In a collision, an unrestrained child, even a tiny baby, can become a projectile inside the vehicle.
GETTING STARTED Power Lumbar • Push the switch forward to increase the lumbar support. Push the switch rearward to decrease the lumbar support. • Pushing upward or downward on the switch will raise and lower the position of the support. Manual Seat Adjustment Forward/Rearward • Lift up on the adjusting bar located at the front of the seat near the floor and release at the desired position.
GETTING STARTED Easy Entry Seats • Pull forward on the lever, located on the side of the seatback, to dump the seatback forward and slide the seat forward. You can also temporarily remove the seat belt from the guide loop on the seat and allow the seat belt to retract out of the way. This allows for easier access to the rear seat. CAUTION! DO NOT place any article under a power seat or impede its ability to move as it may cause damage to the seat controls.
GETTING STARTED WARNING! • Be certain that the seatback is securely locked into position. If the seatback is not securely locked into position, the seat will not provide the proper stability for child seats and/or passengers. An improperly latched seat could cause serious injury. • The cargo area in the rear of the vehicle (with the rear seatbacks in the locked-up or folded-down position) should not be used as a play area by children when the vehicle is in motion.
GETTING STARTED WARNING! (Continued) • Do not place anything on the seat that insulates against heat, such as a blanket or cushion. This may cause the seat heater to overheat. Sitting in a seat that has been overheated could cause serious burns due to the increased surface temperature of the seat. TILT / TELESCOPING STEERING COLUMN • The tilt/telescoping control handle is located below the steering wheel at the end of the steering column.
OPERATING YOUR VEHICLE TURN SIGNAL/WIPER/WASHER/HIGH BEAM LEVER Turn Signal/Lane Change Assist • Tap the lever up or down once and the turn signal (right or left) will flash three times and automatically turn off. Front Wipers Intermittent, Low And High Operation • Rotate the end of the lever to the first detent position for one of five intermittent settings, the second detent for low wiper operation and the third detent for high wiper operation.
OPERATING YOUR VEHICLE HEADLIGHT SWITCH Automatic Headlights/Parking Lights/Headlights • Rotate the headlight switch, located on the instrument panel to the left of the steering wheel, to the first detent for and to the parking lights . second detent for headlights • With the parking lights or low beam headlights on, push the headlight switch once for fog lights. • Rotate the headlight switch to “A” for AUTO headlights.
OPERATING YOUR VEHICLE SPEED CONTROL • The speed control switches are located on the steering wheel. Cruise ON/OFF • Push the ON/OFF button to activate the Speed Control. will appear on the • CRUISE READY instrument cluster to indicate the Speed Control is on. • Push the ON/OFF button a second time to turn the system off. Set • With the Speed Control on, push and release the SET – button to set a desired speed.
OPERATING YOUR VEHICLE WARNING! (Continued) • Electronic Speed Control can be dangerous where the system cannot maintain a constant speed. Your vehicle could go too fast for the conditions, and you could lose control. A collision could be the result. Do not use Electronic Speed Control in heavy traffic or on roads that are winding, icy, snow-covered or slippery.
OPERATING YOUR VEHICLE AUTOMATIC TEMPERATURE CONTROLS (ATC) Automatic Operation • Turn the Mode and Blower Controls to the AUTO position. • Select the desired temperature by rotating the Temperature Control. • The system will maintain the set temperature automatically. Air Conditioning (A/C) • If the air conditioning button is pressed while in the AUTO mode, the indicator light may flash three times to indicate the cabin air is being controlled automatically.
OPERATING YOUR VEHICLE POWER SUNROOF • The power sunroof switch is located on the overhead console. Opening Sunroof Express • Press the switch rearward and release. The sunroof will fully open and stop automatically. Closing Sunroof Express • Press the switch forward and release. The sunroof will close automatically from any position. Manual Open/Close • Press and hold the switch rearward to open or forward to close the sunroof.
OPERATING YOUR VEHICLE WIND BUFFETING • Wind buffeting can be described as a helicopter-type percussion sound. If buffeting occurs with the rear windows open, adjust the front and rear windows together. • If buffeting occurs with the sunroof open, adjust the sunroof opening, or adjust any window. This will minimize buffeting.
ELECTRONICS YOUR VEHICLE'S SOUND SYSTEM 28
ELECTRONICS 29
ELECTRONICS NON-TOUCH-SCREEN RADIOS Media Center 130 (Sales Code RES) Media Center 130 with Satellite Radio (Sales Code RES + RSC) 30
ELECTRONICS NOTE: Your radio may not be equipped with the Uconnect™ Voice Command and Uconnect™ Phone features. To determine if your radio has these features, press the Voice Command button on the radio. You will hear a voice prompt if you have the feature, or see a message on the radio stating “Uconnect Phone not available” if you do not. • Your radio has many features that add to the comfort and convenience of you and your passengers.
ELECTRONICS TOUCH-SCREEN RADIOS Media Center 430/430N CD/DVD/HDD (Sales Code RBZ/RHB) NOTE: Your radio may not be equipped with the Uconnect™ Voice Command and Uconnect™ Phone features. To determine if your radio has these features, press the Voice Command button on the radio. You will hear a voice prompt if you have the feature, or see a message on the radio stating “Uconnect Phone not available” if you do not.
ELECTRONICS • The functions of the portable device are controlled using the device buttons. The volume may be controlled using the radio or portable device. Clock Setting • Turn the radio on, then touch the screen where the time is displayed. • Touch the USER CLOCK soft-key (Navigation radio only). • To adjust the hours, touch either the HOUR FORWARD or HOUR BACKWARD soft-key. • To adjust the minutes, touch either the MINUTE FORWARD or MINUTE BACKWARD soft-key.
ELECTRONICS • Touch one of the ADD PICTURES soft-keys, then select the type of media inserted. • Use the PAGE soft-keys to page through a list of pictures and press the picture you would like to import. • Confirm your selection by touching the YES soft-key. The imported picture is now available in the MANAGE MY PICTURES screen. • In order to display the imported picture in the radio screen, touch the desired picture soft-key. • Select this picture by pressing the PICTURE VIEW soft-key.
ELECTRONICS Entering a Destination/Finding a Point of Interest • Touch the NAV soft-key in the upper-right corner of your radio screen, to access the Navigation system. • Touch the Where To? soft-key to program a destination. • Next touch one of the subcategories to search for your destination. Address, Points of Interest, Recently Found, Favorites and Intersection are a few of the options.
ELECTRONICS STEERING WHEEL AUDIO CONTROLS • The steering wheel audio controls are located on the rear surface of the steering wheel. Right Switch • Press the switch up or down to increase or decrease the volume. • Press the button in the center to change modes AM/FM/CD/SAT. Left Switch • Press the switch up or down to search for the next listenable station or select the next or previous CD track.
ELECTRONICS • (After the BEEP), say “Uconnect setup”. • (After the BEEP), say “phone pairing”. • (After the BEEP), say “pair a phone”. • Follow the audible prompts. • You will be asked to enter a four-digit Personal Identification Number (PIN), which you will later need to enter into your mobile phone. You can enter any four-digit PIN. You will not need to remember this PIN after the initial pairing process.
ELECTRONICS NOTE: To access the tutorial, press the Uconnect™ hard-key. After the BEEP, say “tutorial”. Press any hard-key/button or touch the display (Touch-Screen radio) to cancel the tutorial. WARNING! • Any voice commanded system should be used only in safe driving conditions following local laws and phone use. All attention should be kept on the roadway ahead. Failure to do so may result in a collision causing you and others to be severely injured or killed.
ELECTRONICS • Use the radio ON/OFF VOLUME rotary knob to adjust the volume to a comfortable level while the Voice Command system is speaking. The volume setting for Voice Command is different than the audio system. • Refer to the Understand The Features Of Your Vehicle section of your vehicle's Owner's Manual on the DVD for further details. WARNING! Any voice commanded system should be used only in safe driving conditions following local laws and phone use.
ELECTRONICS NOTE: • The USB port supports certain Mini, Classic, Nano, Touch, and iPhone® devices. The USB port also supports playing music from compatible external USB Mass Storage Class memory devices. For supported audio file formats, refer to the USB Port section on the Owner's Manual on the DVD. Refer to www.dodge.com/uconnect website for a list of tested iPod®s. Some iPod® software versions may not fully support the USB port features. Please visit Apple’s website for iPod® software updates.
ELECTRONICS Compass Calibration • This compass is self-calibrating, which eliminates the need to set the compass manually. When the vehicle is new, the compass may appear erratic and the EVIC will display “CAL” until the compass is calibrated. • You may also calibrate the compass by completing one or more 360 degree turns (in an area free from large metal or metallic objects) until the “CAL” message displayed in the EVIC turns off. The compass will now function normally.
ELECTRONICS Unlock On First Press • To unlock either the driver's side, or all doors, on the first press of the UNLOCK button: • Press and hold the LOCK button for at least 4 seconds, but no longer than 10 seconds. Then, press and hold the UNLOCK button while still holding the LOCK button. • Release both buttons at the same time. Auto Unlock Doors On Exit • To have all of the vehicle doors unlock when any door is opened: • Enter your vehicle and close all the doors.
ELECTRONICS UNIVERSAL GARAGE DOOR OPENER (HomeLink ) ® Programming HomeLink® Begin Programming • The HomeLink® buttons are located in the overhead console. • Erase all channels before you begin programming by holding the two outside buttons for up to 20 seconds until the red indicator flashes. • Park your vehicle outside of the garage and turn the ignition switch to the ON/RUN position.
ELECTRONICS Programming A Rolling Code System • At the garage door opener motor (in the garage), locate the “learn” or “programming” button. This can usually be found where the hanging antenna wire is attached to the garage door opener motor (it is NOT the button normally used to open and close the door). • Firmly press and release the “learn” or “programming” button. The name and color of the button may vary by manufacturer.
ELECTRONICS POWER OUTLET • There are two 12 Volt electrical outlets on this vehicle. • The outlet on the front console has power available only when the ignition is in the ON/RUN position. If desired, this outlet can be converted by your authorized dealer to provide power with the ignition switch in the LOCK position. • The second outlet in the center console is powered directly from the battery (power available at all times).
46 Engine/Transmission Frontal Area 12 sq ft (1.11 sq m) 3.6L Automatic 12 sq ft (1.11 sq m) 5.7L Automatic Refer to local laws for maximum trailer towing speeds Max. GTW (Gross Trailer Wt.) 1,000 lbs (454 kg) 1,000 lbs (454 kg) Max. Tongue Wt.
UTILITY RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) Towing This Vehicle Behind Another Vehicle — Automatic Transmission • Recreational towing (with all four wheels on the ground, or using a tow dolly) is NOT ALLOWED. The only acceptable method for towing this vehicle (behind another vehicle) is on a vehicle trailer with all four wheels OFF the ground CAUTION! • Exceeding these towing limits may cause severe transmission damage. Such damage is not covered by the New Vehicle Limited Warranty.
WHAT TO DO IN EMERGENCIES 24-HOUR TOWING ASSISTANCE - U.S. ONLY • Dial toll-free 1-800-521-2779 or 1-800-363-4869 for Canadian residents. • Provide your name, vehicle identification number and license plate number. • Provide your location, including telephone number, from which you are calling. • Briefly describe the nature of the problem and answer a few simple questions. • You will be given the name of the service provider and an estimated time of arrival.
WHAT TO DO IN EMERGENCIES • When the malfunction indicator is illuminated, the system may not be able to detect or signal low tire pressure as intended. TPMS malfunctions may occur for a variety of reasons, including the installation of replacement or alternate tires or wheels on the vehicle that prevent the TPMS from functioning properly.
WHAT TO DO IN EMERGENCIES WARNING! Driving a vehicle with the red brake light on is dangerous. Part of the brake system may have failed. It will take longer to stop the vehicle. You could have a collision. Have the vehicle checked immediately. - Malfunction Indicator Light (MIL) • Certain conditions, such as a loose or missing gas cap, poor fuel quality, etc., may illuminate the MIL after engine start. The vehicle should be serviced if the light stays on through several typical driving cycles.
WHAT TO DO IN EMERGENCIES - Electronic Throttle Control (ETC) Light • This light informs you of a problem with the Electronic Throttle Control (ETC) system. • If a problem is detected, the light will come on while the engine is running. Cycle the ignition when the vehicle has completely stopped and the shift lever is placed in the PARK position; the light should turn off.
WHAT TO DO IN EMERGENCIES • You can also turn the Temperature Control to maximum heat, the Mode Control to floor and the Fan Control to high. This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system. • If the temperature reading does not return to normal, turn the engine off immediately. • We recommend that you do not operate the vehicle or engine damage will occur. Have the vehicle serviced immediately.
WHAT TO DO IN EMERGENCIES JACKING, TIRE CHANGING Jack/Spare Tire Location Preparations For Jacking • Park on a firm, level surface. Avoid ice or slippery areas. • Set the parking brake and shift the transmission into PARK. • Turn the ignition to LOCK and turn on the Hazard Warning flasher. • Block both the front and rear of the wheel diagonally opposite of the jacking position. For example, if changing the right front tire, block the left rear wheel.
WHAT TO DO IN EMERGENCIES Jacking And Tire Changing Instructions • Remove the spare tire, jack and lug wrench. • If equipped with steel wheels, do not remove the wheel cover at this time. If equipped with aluminum wheels where the center cap covers the lug nuts, use the lug wrench to pry the center cap off carefully before raising the vehicle. • Loosen (but do not remove) the wheel lug nuts by turning them counterclockwise one turn while the wheel is still on the ground.
WHAT TO DO IN EMERGENCIES WARNING! • Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. • Getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never get any part of your body under a vehicle that is on a jack.
WHAT TO DO IN EMERGENCIES JUMP-STARTING • If your vehicle has a discharged battery it can be jumpstarted using a set of jumper cables and a battery in another vehicle or by using a portable battery booster pack. • Jump-starting can be dangerous if done improperly so please follow the procedures in this section carefully. NOTE: When using a portable battery booster pack follow the manufacturer’s operating instructions and precautions.
WHAT TO DO IN EMERGENCIES • Disconnect the opposite end of the positive (+) jumper cable from the positive (+) post of the booster battery. • Disconnect the positive (+) end of the jumper cable from the remote positive (+) post of the discharged vehicle. • If frequent jump-starting is required to start your vehicle you should have the battery and charging system inspected at your authorized dealer.
WHAT TO DO IN EMERGENCIES SHIFT LEVER OVERRIDE • If a malfunction occurs and the shift lever cannot be moved out of the PARK position, you can use the following procedure to temporarily move the shift lever: • To access the shift lever override, remove the shift lever manual override cover which is located on the PRNDL bezel next to the shift lever. The override access port is at the front of the cubby bin. • Firmly set the parking brake.
NOT Permitted Shift lever must be in NEUTRAL. The distance to be traveled must not exceed 15 mi (24 km), and the towing speed must not exceed 30 mph (48 km/h). Shift lever must be in NEUTRAL. There is no limitation on the distance to be traveled.
WHAT TO DO IN EMERGENCIES FREEING A STUCK VEHICLE • If your vehicle becomes stuck in mud, sand or snow, it can often be moved by a rocking motion. Turn your steering wheel right and left to clear the area around the front wheels. Then, move the shift lever back and forth between REVERSE and 1st gear. Using minimal accelerator pedal pressure to maintain the rocking motion, without spinning the wheels, is most effective.
WHAT TO DO IN EMERGENCIES EVENT DATA RECORDER (EDR) • This vehicle is equipped with an event data recorder (EDR). The main purpose of an EDR is to record, in certain crash or near crash-like situations, such as an air bag deployment or hitting a road obstacle, data that will assist in understanding how a vehicle’s systems performed. The EDR is designed to record data related to vehicle dynamics and safety systems for a short period of time, typically 30 seconds or less.
MAINTAINING YOUR VEHICLE OPENING THE HOOD • Pull the hood release lever located on the instrument panel, below the steering column. • Raise the hood and locate the safety catch lever, in the middle of the hood opening. • Move the safety latch while lifting the hood at the same time. • Insert the support rod into the slot on the hood. • To close the hood, remove the support rod and place it in the retaining clip, then lower the hood slowly.
3.
5.
6.
MAINTAINING YOUR VEHICLE FLUIDS AND CAPACITIES Component Fluid, Lubricant, or Genuine Part Capacities Engine Coolant 3.6L MOPAR® Antifreeze/ Coolant Five Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) or equivalent. 11.1 Quarts (10.5 Liters) Includes heater and coolant recovery bottle filled to MAX level. Engine Coolant 5.7L MOPAR® Antifreeze/ Coolant Five Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) or equivalent. 14.7 Quarts (13.
MAINTAINING YOUR VEHICLE Component Fluid, Lubricant, or Genuine Part Engine Oil Filter 3.6L, 5.7L, 6.4L MOPAR® Engine Oil Filter or equivalent. — Spark Plug 3.6L RER8ZWYCB4 (Gap 0.031 in [0.79 mm]) — Spark Plug 5.7L LZFR5C–11 (Gap 0.043 in [1.1 mm]) — Spark Plug 6.4L PLZTR5A-13 (Gap.040 in [1.01 mm]) — Automatic Transmission MOPAR® ATF+4® Automatic Transmission Fluid or equivalent licensed ATF+4® product. — MOPAR® ATF+4® Automatic Transmission Fluid or equivalent licensed ATF+4® product.
68 X X X X X X X X X X X X X X X X X X X X X X X X X X X • • * This maintenance is recommended by the manufacturer to the owner, but is not required to maintain emissions warranty. Refer to the Owner's Manual on the DVD for complete maintenance schedule. X X X X X X X X X X X X X 64,000 72,000 80,000 88,000 96,000 104,000 48 54 60 66 72 78 104,000 117,000 130,000 143,000 156,000 169,000 X X X X X X X X 56,000 42 91,000 X Inspect and replace PCV valve.
MAINTAINING YOUR VEHICLE Maintenance Record Odometer Date Signature, Authorized Service Center 8,000 Miles (13,000 km) or 6 Months 16,000 Miles (26,000 km) or 12 Months 24,000 Miles (39,000 km) or 18 Months 32,000 Miles (52,000 km) or 24 Months 40,000 Miles (65,000 km) or 30 Months 48,000 Miles (78,000 km) or 36 Months 56,000 Miles (91,000 km) or 42 Months 64,000 Miles (104,000 km) or 48 Months 72,000 Miles (117,000 km) or 54 Months 80,000 Miles (130,000 km) or 60 Months 88,000 Miles (143,000 km) or 66 M
MAINTAINING YOUR VEHICLE FUSES Integrated Power Module • The Integrated Power Module (fuses) is located in the engine compartment on the right hand side near the Washer Fluid Reservoir. This module contains fuses and relays.
MAINTAINING YOUR VEHICLE Fuses – Rear Power Distribution Center • There is also a power distribution center located in the trunk under the spare tire access panel. This center contains fuses and relays.
MAINTAINING YOUR VEHICLE 37 Cartridge Fuse — 38 — 39 40 — — 42 30 Amp Pink 30 Amp Pink 20 Amp Blue Cavity 43 44 Mini-Fuse Description 15 Amp Transmission Blue 10 Amp Red Cargo Light/Vehicle Information Module – If Equipped 10 Amp Red Heated Mirrors – If Equipped 5 Amp Auto Inside Rearview Mirror/Heated Orange Seats – If Equipped/Switch Bank — Front Blower Motor — Rear Window Defroster — Amplifier/Sunroof – If Equipped TIRE PRESSURES • Check the inflation pressure of each tire, including the
MAINTAINING YOUR VEHICLE WHEEL AND WHEEL TRIM CARE • All wheels and wheel trim, especially aluminum and chrome plated wheels, should be cleaned regularly with a mild soap and water to prevent corrosion. • To remove heavy soil and/or excessive brake dust, use MOPAR® Wheel Cleaner or equivalent or select a non-abrasive, non-acidic cleaner. CAUTION! Do not use scouring pads, steel wool, a bristle brush, or metal polishes. Do not use oven cleaner. These products may damage the wheel's protective finish.
CONSUMER ASSISTANCE CHRYSLER GROUP LLC CUSTOMER CENTER P.O. Box 21–8004 Auburn Hills, MI 48321–8004 Phone: 1–800–423–6343 CHRYSLER CANADA INC. CUSTOMER CENTER WARNING! Engine exhaust, some of its constituents, and certain vehicle components contain, or emit, chemicals known to the State of California to cause cancer and birth defects, or other reproductive harm.
CONSUMER ASSISTANCE NOTE: • The Owner's Manual and User Guide electronic files are also available on the Chrysler, Jeep and Dodge websites. • Click on the "For Owners" tab, select "Owner/Service Manuals", then select your desired model year and vehicle from the drop down lists. REPORTING SAFETY DEFECTS IN THE 50 UNITED STATES AND WASHINGTON, D.C.
MOPAR ACCESSORIES ® AUTHENTIC ACCESSORIES BY MOPAR • The following highlights just some of the many Authentic Dodge Accessories by Mopar featuring a fit, finish, and functionality specifically for your Dodge Challenger. • In choosing Authentic Accessories you gain far more than expressive style, premium protection, or extreme entertainment, you also benefit from enhancing your vehicle with accessories that have been thoroughly tested and factoryapproved.
INDEX Air Conditioning . . . . . . . . Airbag . . . . . . . . . . . . . . Alarm, Panic . . . . . . . . . . Arming Theft System (Security Alarm) . . . . . . . . Automatic Headlights . . . . . Automatic Temperature Control (ATC) . . . . . . . . . . . . . . Automatic Transmission Fluid Type . . . . . . . . . . Axle Fluid . . . . . . . . . . . . . . . . 12 . . . . 22 Fluid Capacities . . . . Fluids . . . . . . . . . . Fog Lights . . . . . . . . Folding Rear Seat . . .
INDEX Maintenance Record . . . . . . . . . . 69 Maintenance Schedule . . . . . . . . 68 MOPAR® Accessories . . . . . . . . . 76 Navigation . . . . . . . . . . . . . . . 34 Oil Change Indicator . . . . . . . . . . 51 Oil, Engine Capacity . . . . . . . . . . . . . . . 66 Overheating, Engine . . . . . . . . . . 51 Panic Alarm . . . . . . . . . . . . Phone (Pairing) . . . . . . . . . . . Phone (Uconnect) . . . . . . . . . Power Glass Sunroof . . . . . . . . . . Outlet (Auxiliary Electrical Outlet) . . . . . .
NOTES 79
NOTES 80
Driving and Alcohol: Drunken driving is one of the most frequent causes of collisions. Your driving ability can be seriously impaired with blood alcohol levels far below the legal minimum. If you are drinking, don’t drive. Ride with a designated non-drinking driver, call a cab, a friend, or use public transportation. WARNING! Driving after drinking can lead to a collision. Your perceptions are less sharp, your reflexes are slower, and your judgment is impaired when you have been drinking.
This guide has been prepared to help you get quickly acquainted with your new Dodge and to provide a convenient reference source for common questions. However, it is not a substitute for your Owner’s Manual. For complete operational instructions, maintenance procedures and important safety messages, please consult your Owner’s Manual, Navigation/Media Center Manuals, Multimedia User Manual and other Warning Labels in your vehicle. Not all features shown in this guide may apply to your vehicle.
