2011 Grand Cherokee 2011 OWNER’S MANUAL Chrysler Group LLC 11WK741-126-AB Second Edition Printed in U.S.A.
VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name Chrysler Group LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefore. DRIVING AND ALCOHOL Drunken driving is one of the most frequent causes of accidents. Your driving ability can be seriously impaired with blood alcohol levels far below the legal minimum. If you are drinking, don’t drive. Ride with a designated non-drinking driver, call a cab, a friend, or use public transportation.
SECTION TABLE OF CONTENTS PAGE 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 2 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99 3 4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION 1 CONTENTS 䡵 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 Warnings And Cautions . . . . . . . . . . . . . . . . . . . 8 䡵 Rollover Warning . . . . . . . . . . . . . . . . . . . . . . . 5 䡵 Vehicle Identification Number .............. 8 䡵 How To Use This Manual . . . . . . . . . . . . . . . . . . 6 䡵 Vehicle Modifications/Alterations . . . . . . . . . . . .
4 INTRODUCTION INTRODUCTION Congratulations on selecting your new Chrysler Group LLC vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. This is a specialized utility vehicle, it can go places and perform tasks for which conventional two-wheel drive enclosed vehicles were not intended.
INTRODUCTION NOTE: After you read the manual, it should be stored in the vehicle for convenient referencing and remain with the vehicle when sold, so that the new owner will be aware of all safety warnings. When it comes to service, remember that your authorized dealer knows your vehicle best, has factory-trained technicians and genuine MOPAR威 parts, and cares about your satisfaction. ROLLOVER WARNING Utility vehicles have a significantly higher rollover rate than other types of vehicles.
6 INTRODUCTION Failure to use the driver and passenger seat belts provided is a major cause of severe or fatal injury. In fact, the U.S. government notes that the universal use of existing seat belts could cut the highway death toll by 10,000 or more each year and could reduce disabling injuries by two million annually. In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt. Always buckle up.
INTRODUCTION 7
8 INTRODUCTION WARNINGS AND CAUTIONS This Owner’s Manual contains WARNINGS against operating procedures that could result in a collision or bodily injury. It also contains CAUTIONS against procedures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important information. Observe all Warnings and Cautions.
INTRODUCTION 9 VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS 䡵 A Word About Your Keys . . . . . . . . . . . . . . . . . 14 䡵 Vehicle Security Alarm — If Equipped . . . . . . . . 20 ▫ Wireless Ignition Node (WIN) . . . . . . . . . . . . 14 ▫ Rearming The System . . . . . . . . . . . . . . . . . . 21 ▫ Key FOB . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 ▫ To Arm The System . . . . . . . . . . . . . . . . . . . 21 ▫ Removing Key FOB From Ignition . . . . . . . . . 16 ▫ To Disarm The System . . .
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Remote Open Window Feature — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 25 ▫ Using The Panic Alarm . . . . . . . . . . . . . . . . . 25 ▫ Programming Additional Transmitters . . . . . . 26 ▫ Transmitter Battery Replacement . . . . . . . . . . 26 ▫ General Information . . . . . . . . . . . . . . . . . . . 28 䡵 Remote Starting System — If Equipped . . . . . . . 28 ▫ How To Use Remote Start . . . . . . . . . . . . . . . 29 䡵 Door Locks . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Automatic Locking Retractor Mode (ALR) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 56 ▫ Seat Belt Pretensioners . . . . . . . . . . . . . . . . . 57 ▫ Supplemental Active Head Restraints (AHR) . . 57 ▫ Enhanced Seat Belt Use Reminder System (BeltAlert威) . . . . . . . . . . . . . . . . . . . . . . . . . 61 ▫ Seatbelt Lock Out . . . . . . . . . . . . . . . . . . . . . 63 ▫ Seat Belts And Pregnant Women . . . . . . . . . .
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS Your vehicle uses a keyless ignition system. This system consists of a Key Fob with Remote Keyless Entry (RKE) transmitter and a Wireless Ignition Node (WIN) with integral ignition switch. You can insert the Key Fob into the ignition switch with either side up. Wireless Ignition Node (WIN) The Wireless Ignition Node (WIN) operates similar to an ignition switch.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 Key Fob The Key Fob operates the ignition switch. Insert the square end of the key fob into the ignition switch located on the instrument panel and rotate to the desired position. It also contains the Remote Keyless Entry (RKE) transmitter and an emergency key, which stores in the rear of the Key Fob.
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To remove the emergency key, slide the mechanical latch Removing Key Fob From Ignition at the top of the Key Fob sideways with your thumb and Place the shift lever in PARK. Turn the Key Fob to the OFF position and then remove the Key Fob. then pull the key out with your other hand. With the Keyless Enter-N-Go feature, the EVIC will display the ignition switch position “OFF/ACC/RUN”.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The power window switches, radio, power sunroof (if equipped), and power outlets will remain active for up to 10 minutes after the ignition switch is turned to the LOCK position. Opening either front door will cancel this feature. The time for this feature is programmable. Refer to “Electronic Vehicle Information Center (EVIC)/Personal Settings (Customer-Programmable Features)” in “Understanding Your Instrument Panel” for further information.
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The system uses the factory-mated Key Fob with Remote Keyless Entry (RKE) transmitter and Wireless Ignition Node (WIN) to prevent unauthorized vehicle operation. Therefore, only Key Fobs that are programmed to the vehicle can be used to start and operate the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If the Vehicle Security Light turns on during normal vehicle operation (vehicle running for longer than 10 seconds), it indicates that there is a fault in the electronics. Should this occur, have the vehicle serviced as soon as possible by an authorized dealer. CAUTION! The Sentry Key威 Immobilizer system is not compatible with some after-market remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection.
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Duplication of Key Fobs may be performed at an autho- • This device must accept any interference that may be rized dealer, this procedure consists of programming a received, including interference that may cause undeblank Key Fob to the vehicle electronics. A blank Key Fob sired operation. is one that has never been programmed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: The Panic and Security alarms are quite different. Please take a moment to activate the Panic and the Security modes to hear the differences in the horn. In case one should go off in the future, you will need to know which mode has been activated in order to deactivate it.
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Disarm The System Vehicles Not Equipped With Keyless Enter-N-Go To disarm the Vehicle Security Alarm, you will need to press the UNLOCK button on the RKE transmitter or turn the ignition switch to the ON/RUN position. If something has triggered the Vehicle Security Alarm in your absence, the horn will sound three times when you unlock the doors. Check the vehicle for tampering.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The lights also will fade to off if you turn on the ignition after you close all the doors. Refer to “Electronic Vehicle Information Center (EVIC)/Personal Settings (CustomerProgrammable Features)” in “Understanding Your Instrument Panel” for further information. NOTE: None of the courtesy lights will operate if the dimmer control is in the “defeat” position (extreme downward position), unless the overhead map/reading lights are turned on manually.
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Flash Lamps With Remote Key Lock This feature will cause the turn signal lamps to flash when the doors are locked or unlocked with the RKE transmitter. This feature can be turned on or off. To change the current setting, refer to “Electronic Vehicle Information Center (EVIC)/Personal Settings (CustomerProgrammable Features)” in “Understanding Your InRefer to “Keyless Enter-N-Go” under “Things To Know strument Panel” for further information.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Lock The Doors Press and release the LOCK button on the RKE transmitter to lock all doors. The turn signal lamps will flash and the horn will chirp to acknowledge the signal. 25 Remote Open Window Feature — If Equipped This feature allows you to remotely lower both front door windows at the same time.
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: The interior lights will turn off if you turn the ignition switch to the ACC or ON/RUN position while the Panic Alarm is activated. However, the exterior lamps and horn will remain on. 1. Remove the emergency key by sliding the mechanical latch at the top of the RKE transmitter sideways with your thumb and then pull the key out with your other hand.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 2. Insert the tip of the emergency key or a #2 flat blade screwdriver into the slot and gently pry the two halves of the RKE transmitter apart. Make sure not to damage the seal during removal. 2 Separating RKE Transmitter Inserting Emergency Key Into Slot 3. Remove and replace the battery. When replacing the battery, match the + sign on the battery to the + sign on the inside of the battery clip, located on the back cover.
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. To assemble the RKE transmitter case, snap the two If your RKE transmitter fails to operate from a normal distance, check for these two conditions: halves together. 1. A weak battery in the RKE transmitter. The expected General Information This device complies with part 15 of the FCC rules and life of the battery is a minimum of three years. RSS 210 of Industry Canada. Operation is subject to the 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE How To Use Remote Start All of the following conditions must be met before the engine will remote start: • Shift lever in PARK • Doors closed • Hood closed • Liftgate/Flipper Glass closed • Hazard switch off • Brake switch inactive (brake pedal not pressed) • Ignition key removed from ignition switch • Battery at an acceptable charge level • RKE PANIC button not pressed 29 WARNING! • Do not start or run an engine in a closed garage or confined area.
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Remote Start Aborted — Hood Ajar • Remote Start Aborted — Fuel Low • Remote Start Aborted — System Fault • Remote Start Disabled — Start Vehicle to Reset NOTE: • If an engine fault is present or fuel level is low, the vehicle will start and then shutdown in 10 seconds. • The park lamps will turn on and remain on during Remote Start mode.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 NOTE: To Exit Remote Start Mode Without Driving The • For vehicles not equipped with Keyless Enter-N-Go Vehicle Press and release the REMOTE START button one time or feature, the ignition switch must be in the ON/RUN allow the engine to run for the entire 15 minute cycle. position in order to drive the vehicle.
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Remote Start Comfort Systems — If Equipped When remote start is activated, the heated steering wheel, and driver heated seat features will automatically turn on in cold weather. In warm weather, the driver vented seat feature will automatically turn on when the remote start is activated. These features will stay on through the duration of remote start or until the ignition switch is turned to the ON/RUN position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 WARNING! • For personal security and safety in the event of an accident, lock the vehicle doors when you drive, as well as when you park and leave the vehicle. • When leaving the vehicle, always remove the key from the ignition and lock your vehicle. Do not leave unattended children in the vehicle, or with access to an unlocked vehicle. Unsupervised use of vehicle equipment may cause severe personal injuries and death.
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If a rear door is locked, it cannot be opened from inside Automatic Unlock On Exit Feature — If Equipped the vehicle without first unlocking the door. The door If Auto Unlock is enabled, this feature will unlock all the doors when the driver’s door is opened if the vehicle is may be unlocked manually by raising the lock knob. stopped and in PARK or NEUTRAL.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 3. Repeat steps 1 and 2 for the opposite rear door. 2 Child-Protection Door Lock Function Child-Protection Door Lock Location WARNING! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the Child-Protection locks are engaged (locked).
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: For emergency exit from the rear seats when the • If a passive entry door handle has not been used for Child-Protection Door Lock System is engaged, manually 72 hours, the passive entry feature for the handle may raise the door lock knob to the unlocked position, roll time out. Pulling the deactivated front door handle down the window, and open the door using the outside will reactivate the door handle’s passive entry feature. door handle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 To Unlock From The Passenger Side: With a valid Passive Entry RKE transmitter within 5 ft (1.5 m) of the passenger door handle, grab the front passenger door handle to unlock all four doors automatically. The interior door panel lock knob will raise when the door is unlocked.
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If one of the vehicle doors is open and the door panel switch is used to lock the vehicle, once all open doors have been closed, the vehicle checks the inside and outside of the vehicle for any valid Passive Entry RKE transmitters.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 NOTE: If “Unlock All Doors 1st Press” is programmed in EVIC, all doors will unlock when you push the button on the liftgate. If ⬙Unlock Driver Door 1st press⬙ is programmed in EVIC, the liftgate and Flipper glass will unlock when you press the button on the liftgate For further information, refer to “Electronic Vehicle Information Center (EVIC)/Personal Settings (Customer-Programmable Features)” in “Understanding Your Instrument Panel”.
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: • After pressing the door handle LOCK button, you must wait two seconds before you can lock or unlock the doors, using either passive entry door handle. • The passive entry system will not operate if the RKE transmitter battery is dead. The vehicle doors can also be locked by using the RKE transmitter lock button or the lock button located on the vehicle’s interior door panel.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Never leave children in a vehicle with the key in the ignition switch or leave a vehicle with Keyless EnterN-Go in the ACC or ON/RUN position. Occupants, particularly unattended children, can become entrapped by the windows while operating the power window switches. Such entrapment may result in serious injury or death. Auto-Down Both the driver and front passenger window switches have an “Auto-Down” feature.
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE during Auto Up. If this happens, pull the switch lightly to Window Lockout Button the first detent and hold it to close the window manually. The Window Lockout button on the driver’s door allows you to disable the window controls on the rear doors. To WARNING! disable the window controls on the rear doors, press the Window Lockout button. To enable the window controls, There is no anti-pinch protection when the window press the Window Lockout button again.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occurrence and can be minimized. If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting.
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Liftgate Flipper Glass The liftgate flipper glass is also unlocked when the liftgate is unlocked. To open the flipper glass, push up on the window switch located on the liftgate. Once the liftgate flipper glass has been opened, connection to the rear window wiper is interrupted, preventing activation of the rear wiper blade while the flipper glass is open.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Power Liftgate — If Equipped The power liftgate may be opened by pulling up on the liftgate handle or by pressing the LIFTGATE button on the Remote Keyless Entry (RKE) transmitter. Press the LIFTGATE button on the RKE transmitter twice within five seconds, to open the power liftgate. Once the liftgate is open, pressing the button twice within five seconds a second time will close the liftgate.
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! During power operation, personal injury or cargo damage may occur. Ensure the liftgate travel path is clear. Make sure the liftgate is closed and latched before driving away. button to operate. If the liftgate is not fully open, press the Liftgate button on the Key Fob to fully open the liftgate, and then press it again to close.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • If the power liftgate encounters multiple obstructions within the same cycle, the system will automatically stop and the liftgate must be opened or closed manually. 47 Gas props support the liftgate in the open position. However, because the gas pressure drops with temperature, it may be necessary to assist the props when opening the liftgate in cold weather.
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • An energy-absorbing steering column and steering NOTE: The Advanced Front Airbags have a multistage inflator design. This allows the airbag to have different wheel rates of inflation based on the severity and type of • Knee bolsters for front seat occupants collision. • Front seat belts incorporate pretensioners to enhance Please pay close attention to the information in this occupant protection by managing occupant energy section.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Buckle up even though you are an excellent driver, even on short trips. Someone on the road may be a poor driver and cause an accident that includes you. This can happen far away from home or on your own street. Research has shown that seat belts save lives, and they can reduce the seriousness of injuries in an accident. Some of the worst injuries happen when people are thrown from the vehicle.
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • It is dangerous to ride in a cargo area, inside or outside of a vehicle. In an accident, people riding in these areas are more likely to be seriously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • Be sure everyone in your vehicle is in a seat and using a seat belt properly. Lap/Shoulder Belt Operating Instructions Latch Plate 1.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 WARNING! • A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you properly. In a sudden stop you could move too far forward, increasing the possibility of injury. Wear your seat belt snugly.
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • A belt that is worn under your arm is dangerous. Your body could strike the inside surfaces of the vehicle in an accident, increasing head and neck injury. A belt worn under the arm can cause internal injuries. Ribs aren’t as strong as shoulder bones. Wear the belt over your shoulder so that your strongest bones will take the force in a collision. • A shoulder belt placed behind you will not protect you from injury during an accident.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 WARNING! A frayed or torn belt could rip apart in an accident and leave you with no protection. Inspect the belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Seat belt assemblies must be replaced after an accident if they have been damaged (bent retractor, torn webbing, etc.).
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. At about 6 to 12 in (15 to 30 cm) above the latch plate, grasp and twist the belt webbing 180 degrees to create a fold that begins immediately above the latch plate. 3. Slide the latch plate upward over the folded webbing. The folded webbing must enter the slot at the top of the latch plate. 4. Continue to slide the latch plate up until it clears the folded webbing.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: The adjustable upper shoulder belt anchorage is equipped with an Easy Up feature. This feature allows the shoulder belt anchorage to be adjusted in the upward position without pushing the release button. To verify the shoulder belt anchorage is latched, pull downward on the shoulder belt anchorage until it is locked into position.
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Automatic Locking Retractor Mode (ALR) — If Equipped First Row In this mode, the shoulder belt is automatically preSecond Row locked. The belt will still retract to remove any slack in Third Row the shoulder belt. The Automatic Locking Mode is available on all passenger-seating positions with a combina• N/A — Not Applicable tion lap/shoulder belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 3. Allow the belt to retract. As the belt retracts, you will Seat Belt Pretensioners hear a clicking sound. This indicates the safety belt is The seat belts for both front seating positions are equipped with pretensioning devices that are designed to now in the Automatic Locking Mode. remove slack from the seat belt in the event of an How To Disengage The Automatic Locking Mode accident.
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE identified by any markings, only through visual inspec- However if during a front impact, a secondary rear tion of the head restraint. The head restraint will be split impact occurs, the AHR may deploy based on the severin two halves, with the front half being soft foam and ity and type of the impact. trim, the back half being decorative plastic.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CAUTION! 59 1. Grasp the deployed AHR from the rear seat. All occupants, including the driver, should not operate a vehicle or sit in a vehicle’s seat until the head restraints are placed in their proper positions in order to minimize the risk of neck injury in the event of an accident.
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Pull down then rearward towards the rear of the vehicle then down to engage the locking mechanism. 3 — Final Downward Movement To Engage Locking Mechanism 1 — Downward Movement 2 — Rearward Movement 4. The AHR front soft foam and trim half should lock into the back decorative plastic half.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 Enhanced Seat Belt Use Reminder System (BeltAlert姞) BeltAlert威 is a feature intended to remind the driver and front passenger (if equipped with front passenger BeltAlert威) to fasten their seatbelts. This feature is active whenever the ignition is on. If the driver or front seat passenger is unbelted, the Seat Belt Reminder Light will turn on and remain on until both front seatbelts are fastened.
62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The front passenger seat BeltAlert威 is not active when the front passenger seat is unoccupied. BeltAlert威 may be triggered when an animal or heavy object is on the front passenger seat or when the seat is folded flat (if equipped). It is recommended that pets be restrained in the rear seat in pet harnesses or pet carriers that are secured by seat belts, and cargo is properly stowed. 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 extender should be used only if the existing belt is not Seatbelt Lock Out The center rear seat belt system has a lock out feature that long enough. When it is not required, remove the exwill not allow you to extract the center webbing unless tender and store it. the rear seat upper latch is engaged. Seat Belts and Pregnant Women We recommend that pregnant women use the seat belts throughout their pregnancy.
64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE instrument panel, above the glove compartment. The The Advanced Front Airbags have a multistage inflator words SRS AIRBAG are embossed on the airbag covers. design. This allows the airbag to have different rates of inflation based on the severity and type of collision. This vehicle may be equipped with driver and/or front passenger seat track position sensors that may adjust the inflation rate of the Advanced Front Airbags based upon seat position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 This vehicle is equipped with Supplemental Seat-Mounted • Steering Wheel and Column Side Airbags (SAB) to provide enhanced protection for an • Instrument Panel occupant during a side impact. The Supplemental SeatMounted Side Airbags are located in the outboard side of • Knee Impact Bolster the front seats.
66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Advanced Front Airbag Features The Advanced Front Airbag system has multistage driver and front passenger airbags. This system provides output appropriate to the severity and type of collision as determined by the Occupant Restraint Controller (ORC), which may receive information from the front impact sensors. The first stage inflator is triggered immediately during an impact that requires airbag deployment. This low output is used in less severe collisions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Supplemental Seat-Mounted Side Airbags (SAB) Supplemental Seat-Mounted Side Airbags provide enhanced protection to help protect an occupant during a side impact. The Supplemental Seat-Mounted Side Airbag is marked with an airbag label sewn into the outboard side of the front seats. Supplemental Seat-Mounted Side Airbag Label 67 When the airbag deploys, it opens the seam between the front and side of the seat’s trim cover.
68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Supplemental Side Airbag Inflatable Curtain (SABIC) SABIC airbags may offer side-impact and vehicle rollover protection to front and rear seat outboard occupants in addition to that provided by the body structure. Each airbag features inflated chambers placed adjacent to the head of each outboard occupant that reduce the potential for side-impact head injuries. The curtains deploy downward, covering both windows on the impact side.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Being too close to the SAB and SABIC airbags during deployment could cause you to be severely injured or killed. • Should a vehicle rollover occur, the pretensioners, SAB and/or SABIC airbags on both sides of the vehicle may deploy.
70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Knee Impact Bolsters The Knee Impact Bolsters help protect the knees of the driver and the front passenger, and position front occupants for the best interaction with the Advanced Front Airbags. WARNING! Infants in rear-facing child restraints should never ride in the front seat of a vehicle with a passenger Advanced Front Airbag. An airbag deployment can cause severe injury or death to infants in that position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 If a child from 1 to 12 years old (not in a rear facing child seat) must ride in the front passenger seat, move the seat as far back as possible and use the proper child restraint. (Refer to “Child Restraints”) If the airbag system in this vehicle needs to be modified to accommodate a disabled person, contact the Customer Center. Phone numbers are provided under ⬙If You Need Assistance⬙.
72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • Being too close to the steering wheel or instrument panel during Advanced Front Airbag deployment could cause serious injury, including death. Airbags need room to inflate. Sit back, comfortably extending your arms to reach the steering wheel or instrument panel. • Supplemental Side Airbag Inflatable Curtains (SABIC) and Supplemental Seat-Mounted Side Airbags (SAB) need room to inflate. Do not lean against the door or window.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 Advanced Front Airbags may deploy in crashes with position, in the ACC position, or not in the ignition, the little vehicle front-end damage but that produce a severe airbag system is not on and the airbags will not inflate. initial deceleration. The ORC contains a backup power supply system that The side airbags will not deploy in all side collisions.
74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Ignoring the Airbag Warning Light in your instrument panel could mean you won’t have the airbags to protect you in a collision. If the light does not come on as a bulb check when the ignition is first turned on, stays on after you start the vehicle, or if it comes on as you drive, have an authorized dealer service the airbag system immediately.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 Based on the severity and type of collision, the side airbag inflator on the crash side of the vehicle may be triggered, releasing a quantity of non-toxic gas. The inflating side airbag exits through the seat seam into the space between the occupant and the door. The side airbags fully inflate in about 10 milliseconds.
76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Front And Side Impact Sensors • Turn on the interior lights, which remain on as long as In front and side impacts, front and side impact sensors the battery has power or until the ignition key is can aid the ORC in determining the appropriate response removed. to certain impact events. • Unlock the doors automatically.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If you do have a collision which deploys the airbags, any or all of the following may occur: 77 throat irritation, move to fresh air. If the irritation continues, see your doctor. If these particles settle on your clothing, follow the garment manufacturer’s instructions for cleaning. • The nylon airbag material may sometimes cause abrasions and/or skin reddening to the driver and front passenger as the airbags deploy and unfold.
78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Maintaining Your Airbag System WARNING! (Continued) WARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. You could be injured if the airbag system is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the steering wheel hub trim cover or the upper right side of the instrument panel.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag Warning Light You will want to have the airbags ready to inflate for your protection in a collision. The Airbag Warning Light monitors the internal circuits and interconnecting wiring associated with airbag system electrical components. While the airbag system is designed to be maintenance free, if any of the following occurs, have an authorized dealer service the airbag system immediately.
80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Whether or not the driver and passenger safety belts To read data recorded by an EDR, special equipment is required, and access to the vehicle or the EDR is needed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 81 There are different sizes and types of restraints for Infants And Child Restraints children from newborn size to the child almost large • Safety experts recommend that children ride enough for an adult safety belt. Always check the child rearward-facing in the vehicle until they are at least seat Owner’s Manual to ensure you have the right seat one year old and weigh at least 20 lbs (9 kg). Two types for your child.
82 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Rearward-facing child seats must never be used in the front seat of a vehicle with the front passenger airbag unless the airbag is turned off. An airbag deployment could cause severe injury or death to infants in this position. • Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE restraint and slide the latch plate into the buckle. Then, pull the shoulder belt until it is fully extended from the retractor. Allow the belt to return into the retractor, pulling on the excess webbing to tighten the lap portion around the child restraint. For additional information refer to ⬙Automatic Locking Retractors Mode⬙ earlier in the Occupant Restraints Section of the owners’ manual. 83 NOTE: For additional information, refer to www.seatcheck.
84 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE with knees bent over the vehicle’s seat cushion while the • If the shoulder belt contacts the face or neck, move the child’s back is against the seatback, they should use a child closer to the center of the vehicle. Never allow a belt-positioning booster seat. The child and beltchild to put the shoulder belt under an arm or behind positioning booster seat are held in the vehicle by the the back. lap/shoulder belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 85 anchors can be readily identified by the symbol located on the seatback directly above the anchorages and are just visible when you lean into the rear seat to install the child restraint. You will easily feel them if you run your finger along the intersection of the seatback and seat cushion surfaces. The vehicle’s seat belt must be used for the center position.
86 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Installing The LATCH-Compatible Child Restraint System We urge you to carefully follow the directions of the manufacturer when installing your child restraint. Not all child restraint systems will be installed as described here. Again, carefully follow the installation instructions that were provided with the child restraint system.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 87 2 Pulling Down The Carpet Floor Panel To Access Top Tether Strap Top Tether Strap Anchorage (Located on Seatback) WARNING! Do not use the cargo tie downs located on the load floor. Improper usage of the tether can lead to a failure of an infant or child restraint. The child could be badly injured or killed.
88 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Many, but not all restraint systems will be equipped with separate straps on each side, with each having a hook or connector for attachment to the lower anchorage and a means of adjusting the tension in the strap. Forwardfacing toddler restraints and some rear-facing infant restraints will also be equipped with a tether strap, a hook for attachment to the tether strap anchorage and a means of adjusting the tension of the strap.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE the child restraint so that it is not necessary to use a locking clip. If the seat belt has a cinching latch plate, pulling up on the shoulder portion of the lap/shoulder belt will tighten the belt. The cinching latch plate will keep the belt tight; however, any seat belt system will loosen with time, so check the belt occasionally and pull it tight if necessary. position has an armrest tether that secures the arm rest in the upward position.
90 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Pull down on the tether to unhook it from the plastic seat and attach the hook to the top tether anchor located on backing, then raise the armrest and attach the tether hook the back of the seat. To access the top tether strap anchorages behind the rear seat, pull the carpeted floor to the strap located on the front of the arm rest. panel away from the seat back, this will expose the top tether strap anchorages.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 91 2 Top Tether Strap Anchorage (Located on Seatback) Top Tether Strap Mounting
92 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor positions directly behind the child seat to secure a child restraint top tether strap. • Do not use the cargo tie downs located on the load floor. Improper usage of the tether can lead to a failure of an infant or child restraint. The child could be badly injured or killed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 93 While cruising, brief full-throttle acceleration within the SAFETY TIPS limits of local traffic laws, contributes to a good break-in. Transporting Passengers Wide-open throttle acceleration in low gear can be detriNEVER TRANSPORT PASSENGERS IN THE CARGO mental and should be avoided. AREA. The engine oil installed in the engine at the factory is a WARNING! high-quality energy conserving type lubricant.
94 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Exhaust Gas WARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (CO) follow these safety tips: Do not run the engine in a closed garage or in confined areas any longer than needed to move your vehicle in or out of the area.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 95 Defroster Check operation by selecting the defrost mode and place the blower control on high speed. You should be able to Seat Belts feel the air directed against the windshield. See your Inspect the belt system periodically, checking for cuts, authorized dealer for service if your defroster is frays, and loose parts. Damaged parts must be replaced inoperable. immediately. Do not disassemble or modify the system.
96 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! (Continued) Pedals that cannot move freely can cause loss of vehicle control and increase the risk of serious personal injury. • Always make sure that floor mats are properly attached to the floor mat fasteners. • Never place or install floor mats or other floor coverings in the vehicle that cannot be properly secured to prevent them from moving and interfering with the pedals or the ability to control the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 97 Periodic Safety Checks You Should Make OutsideThe Vehicle Door Latches Check for positive closing, latching, and locking. Tires Examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread. Inspect the tread and sidewall for cuts and cracks. Check the wheel nuts for tightness. Check the tires (including spare) for proper pressure.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 䡵 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106 ▫ Illuminated Vanity Mirrors . . . . . . . . . . . . . 110 ▫ Inside Day/Night Mirror . . . . . . . . . . . . . . . 106 ▫ Sun Visor Extension — If Equipped . . . . . . . 110 ▫ Automatic Dimming Mirror — If Equipped . . 107 䡵 Blind Spot Monitoring — If Equipped . . . . . . . . 111 ▫ Outside Mirrors . . . . . . . . . . . . . . . . . . . . . 108 ▫ Rear Cross Path . . . . . . . . . .
100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Passenger’s Power Seat . . . . . . . . . . . . . . . . 122 䡵 Driver Memory Seat — If Equipped . . . . . . . . 138 ▫ Power Lumbar — If Equipped . . . . . . . . . . . 124 ▫ Setting Memory Positions And Linking Remote Keyless Entry Transmitter To Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . 139 ▫ Manual Front Seats Forward/Rearward Adjustment . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 ▫ Daytime Running Lights — If Equipped . . . . 147 ▫ Lane Change Assist . . . . . . . . . . . . . . . . . . . 152 ▫ Automatic Headlight Leveling — HID Headlights Only . . . . . . . . . . . . . . . . . . . . . 147 ▫ Flash-To-Pass . . . . . . . . . . . . . . . . . . . . . . . 152 ▫ Headlight Delay . . . . . . . . . . . . . . . . . . . . . 147 ▫ Parking Lights And Panel Lights . . . . . . . . . 148 ▫ Fog Lights — If Equipped . . . . . . . . . . . . . .
102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 䡵 Electronic Speed Control . . . . . . . . . . . . . . . . 161 ▫ To Cancel . . . . . . . . . . . . . . . . . . . . . . . . . . 171 ▫ To Activate . . . . . . . . . . . . . . . . . . . . . . . . . 162 ▫ To Turn Off . . . . . . . . . . . . . . . . . . . . . . . . 172 ▫ To Set A Desired Speed . . . . . . . . . . . . . . . . 163 ▫ To Resume Speed . . . . . . . . . . . . . . . . . . . . 172 ▫ To Deactivate . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 䡵 Parksense威 Rear Park Assist — If Equipped . . . 192 ▫ Parksense威 Sensors . . . . . . . . . . . . . . . . . . . 193 ▫ Parksense威 Warning Display . . . . . . . . . . . . 193 ▫ Parksense威 Display . . . . . . . . . . . . . . . . . . . 194 ▫ Enabling And Disabling Park Sense威 . . . . . . 197 ▫ Service The Parksense威 Rear Park Assist System . . . . . . . . . . . . . . . . . . . . . . . . . . . .
104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 䡵 Power Sunroof — If Equipped . . . . . . . . . . . . 212 ▫ Venting Sunroof – Express . . . . . . . . . . . . . . 216 ▫ Opening Sunroof — Express . . . . . . . . . . . . 213 ▫ Closing Sunroof – Express . . . . . . . . . . . . . . 217 ▫ Closing Sunroof — Express . . . . . . . . . . . . . 213 ▫ Opening Power Shade – Express . . . . . . . . . 217 ▫ Pinch Protect Feature . . . . . . . . . . . . . . . . . 213 ▫ Closing Power Shade – Express . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 䡵 Electrical Power Outlets . . . . . . . . . . . . . . . . . 219 ▫ Cargo Storage Bins . . . . . . . . . . . . . . . . . . . 229 䡵 Power Inverter — If Equipped . . . . . . . . . . . . 222 ▫ Retractable Cargo Area Cover — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . 231 䡵 Cupholders . . . . . . . . . . . . . . . . . . . . . . . . . . 224 䡵 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 225 ▫ Glove Compartment . . . . . . .
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Day/Night Mirror A single ball joint mirror is provided in the vehicle. It is a twist on mirror that has a fixed position. The mirror head can be adjusted up, down, left, and right for various drivers. The mirror should be adjusted to center on the view through the rear window. Headlight glare from vehicles behind you can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 Automatic Dimming Mirror — If Equipped This mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light in the button will illuminate to indicate when the dimming feature is activated. The mirror is twisted on the windshield button counterclockwise and requires no tools for mounting.
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Outside Mirrors To receive maximum benefit, adjust the outside mirrors to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror. WARNING! Vehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they really are. Relying too much on your passenger side convex mirror could cause you to collide with another vehicle or other object.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 Outside Power Mirrors The power mirror switch is located on the driver’s side door trim panel. The power mirror controls consist of mirror select buttons and a four-way mirror control switch. To adjust a mirror, press the mirror select button for the mirror that you want to adjust. Using the mirror control switch, press on any of the four arrows for the direction that you want the mirror to move.
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Heated Mirrors — If Equipped These mirrors are heated to melt frost or ice. This feature is activated whenever you turn on the rear window defroster. Refer to “Rear Window Features” in “Understanding the Features of Your Vehicle” for further information. Illuminated Vanity Mirrors To access an illuminated vanity mirror, flip down one of the visors. Lift the cover to reveal the mirror. The light will turn on automatically.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE BLIND SPOT MONITORING — IF EQUIPPED The Blind Spot Monitoring (BSM) system uses two radarbased sensors, located inside the rear bumper fascia, to detect highway licensable vehicles (automobiles, trucks, motorcycles, etc.) that enter the blind spot zones from the rear/front/side of the vehicle. 111 When the vehicle is started, the BSM warning light will momentarily illuminate in both outside rear view mirrors to let the driver know that the system is operational.
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The BSM system detection zone DOES NOT change if your vehicle is towing a trailer. Therefore, visually verify the adjacent lane is clear for both your vehicle and trailer before making a lane change. If the trailer or other object (i.e., bicycle, sports equipment) extends beyond the side of your vehicle, this may result in the BSM warning light remaining illuminated the entire time the vehicle is in a forward gear.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 The BSM system notifies the driver of objects in the The BSM system can also be configured to sound an detection zones by illuminating the BSM warning light audible (chime) alert and reduces the radio volume to located in the outside mirrors. notify the driver of objects that have entered the detection zones. Refer to “Modes Of Operation” for further information.
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Entering From The Side Entering From The Rear Vehicles that move into your adjacent lanes from either Vehicles that come up from behind your vehicle on either side of the vehicle. side and enter the rear detection zone with a relative speed of less than 30 mph (48 km/h).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Overtaking Traffic If you pass another vehicle slowly (with a relative speed less than 10 mph (16 km/h) and the vehicle remains in the blind spot for approximately 1.5 seconds, the warning light will be illuminated. If the difference in speed between the two vehicles is greater than 10 mph (16 km/h), the warning light will not illuminate.
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The BSM system is designed not to issue an alert on The BSM system will not alert you of objects that are stationary objects such as guardrails, posts, walls, foliage, traveling in the opposite direction of the vehicle in berms, etc. However, occasionally the system may alert adjacent lanes. on such objects. This is normal operation and your vehicle does not require service.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 WARNING! The Blind Spot Monitoring system is only an aid to help detect objects in the blind spot zones. The BSM system is not designed to detect pedestrians, bicyclists, or animals. Even if your vehicle is equipped with the BSM system, always check your vehicles mirrors, glance over your shoulder, and use your turn signal before changing lanes. Failure to do so can result in serious injury or death.
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: In a parking lot situation, oncoming vehicles can be obscured by vehicles parked on either side. If the sensors are blocked by other structures or vehicles, the system will not be able to alert the driver. Modes Of Operation Three selectable modes of operation are available in the Electronic Vehicle Information Center (EVIC).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE signal is then activated, and it corresponds to an alert present on that side of the vehicle, an audible chime will also be sounded. Whenever a turn signal and detected object are present on the same side at the same time, both the visual and audio alerts will be issued. In addition to the audible alert the radio volume (if on) will also be reduced.
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE VOICE COMMAND — IF EQUIPPED Voice Commands can be initiated by pressing the VR located on the radio or steering wheel button controls (if equipped). Refer to “Voice Command” in the Uconnect™ User Manual located on the DVD for further details. SEATS Seats are part of the Occupant Restraint System of the vehicle. WARNING! • It is dangerous to ride in a cargo area, inside or outside of a vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 Adjusting The Seat Forward Or Rearward The seat can be adjusted both forward and rearward. Push the seat switch forward or rearward, the seat will move in the direction of the switch. Release the switch when you have reached the desired position. Adjusting The Seat Up Or Down The height of the seats can be adjusted up or down. Pull upward or push downward on the rear of the seat switch, the seat will move in the direction of the switch.
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Reclining The Seatback The angle of the seatback can be adjusted forward or backward. Push the seatback switch forward or rearward, the seat will move in the direction of the switch. Release the switch when you have reached the desired position. • Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt, which could result in serious injury or death.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Adjusting The Seat Forward Or Rearward The seat can be adjusted both forward and rearward. Push the seat switch forward or rearward, the seat will move in the direction of the switch. Release the switch when you have reached the desired position. Adjusting The Seat Up Or Down The height of the seats can be adjusted up or down. Pull upward or push downward on the seat switch, the seat will move in the direction of the switch.
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Do not place any article under a power seat or impede its ability to move as it may cause damage to the seat controls. Seat travel may become limited if movement is stopped by an obstruction in the seat’s path. Power Lumbar — If Equipped Vehicles equipped with power driver or passenger seats are also equipped with power lumbar. The power lumbar switch is located on the outboard side of the power seat.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Manual Front Seats Forward/Rearward Adjustment Some models may be equipped with manual front driver or passenger seats. The seats can be adjusted forward or rearward by using a bar located by the front of the seat cushion, near the floor. 125 While sitting in the seat, lift up on the bar located under the seat cushion and move the seat forward or rearward. Release the bar once you have reached the desired position.
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Manual Front Passenger Seatback Adjustment — Recline To adjust the seatback, lift the lever located on the outboard side of the seat, lean back to the desired position and release the lever. To return the seatback, lift the lever, lean forward and release the lever. WARNING! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 WARNING! Fold-Flat Passenger Seat Heated Seats — If Equipped On some models, the front and rear seats may be equipped with heaters in both the seat cushions and seatbacks. • Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion or other physical condition must exercise care when using the seat heater.
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Repeated overheating of the seat could damage the heating element and/or degrade the material of the seat. heat in use. Two indicator lights will illuminate for HIGH, one for LOW and none for OFF. Press the switch once to select HIGH-level heating. Press the switch a second time to select LOW-level heating. Press the switch a third time to shut the heating elements OFF.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Heated Seats On some models, the two outboard seats are equipped with heated seats. There are two heated seat switches that allow the rear passengers to operate the seats independently. The heated seat switches for each heater are located on the rear of the center console. 129 You can choose from HIGH, LOW or OFF heat settings. Amber indicator lights in each switch indicate the level of heat in use.
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE to one, indicating the change. The LOW-level setting will turn OFF automatically after a maximum of 45 minutes. Ventilated Seats — If Equipped On some models, both the driver and passenger seats are ventilated. Located in the seat cushion and seatback are small fans that draw the air from the passenger compartment and blow air through fine perforations in the seat cover to help keep the driver and front passenger cooler in higher ambient temperatures.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Head Restraints Head restraints are designed to reduce the risk of injury by restricting head movement in the event of a rearimpact. Head restraints should be adjusted so that the top of the head restraint is located above the top of your ear. WARNING! The head restraints for all occupants must be properly adjusted prior to operating the vehicle or occupying a seat. Head restraints should never be adjusted while the vehicle is in motion.
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To raise the head restraint, pull upward on the head restraint. To lower the head restraint, press the push button, located at the base of the head restraint, and push downward on the head restraint. For comfort the Active Head Restraints can be tilted forward and rearward. To tilt the head restraint closer to the back of your head, pull forward on the bottom of the head restraint.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 • In the event of deployment of an Active Head Restraint, refer to “Occupant Restraints/Resetting Active Head Restraints (AHR)” in “Things to Know Before Starting Your Vehicle” for further information. WARNING! Active Head Restraint (Tilted) NOTE: • The head restraints should only be removed by qualified technicians, for service purposes only. If either of the head restraints require removal, see your authorized dealer.
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! (Continued) • Active Head Restraints may be deployed if they are struck by an object such as a hand, foot or loose cargo. To avoid accidental deployment of the Active Head Restraint ensure that all cargo is secured, as loose cargo could contact the Active Head Restraint during sudden stops. Failure to follow this warning could cause personal injury if the Active Head Restraint is deployed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! 135 1. Pull upward on the release lever to release the seat. Sitting in a seat with the head restraint in its lowered position could result in serious injury or death in a collision. Always make sure the outboard head restraints are in their upright positions when the seat is to be occupied. NOTE: For proper routing of a Child Seat Tether refer to “Occupant Restraints” in “Things to Know Before Starting Your Vehicle” for further information.
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Fold the rear seat completely forward. Rear Seat Folded To Raise Rear Seat Raise the rear seatback and lock it into place. If interference from the cargo area prevents the seatback from fully locking, you will have difficulty returning the seat to its proper position. WARNING! • Be certain that the seatback is securely locked into position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Reclining Rear Seat To recline the seatback, lift the lever located on the outboard side of the seat, lean back and release the lever at the desired position. To return the seatback, lift the lever, lean forward and release the lever. Rear Seat Release 137 WARNING! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest.
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE DRIVER MEMORY SEAT — IF EQUIPPED Once programmed, the memory buttons 1 and 2 on the driver’s door panel can be used to recall the driver’s seat, driver’s outside mirror, adjustable steering wheel position (if equipped), and the radio station preset settings. Your Remote Keyless Entry (RKE) transmitters can also be programmed to recall the same positions when the UNLOCK button is pressed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Setting Memory Positions and Linking Remote Keyless Entry Transmitter to Memory 139 5. Turn on the radio and set the radio station presets (up to 12 AM and 12 FM stations can be set). NOTE: Each time the S (SET) button and a numbered 6. Turn the ignition switch to the LOCK position and button 1 or 2 are pressed, you erase the memory settings remove the key. for that button and store a new one. 7. Press and release the S (SET) button located on the 1.
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE to “Electronic Vehicle Information Center (EVIC)/ To recall the memory setting for driver two, press Customer-Programmable Features” in “Understanding MEMORY button number 2 on the driver’s door, or the UNLOCK button on the RKE transmitter linked to Your Instrument Panel” for further information. memory position 2. 12.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 3. Press and release the memory S (SET) button located Easy Entry/Exit Seat This feature provides automatic driver’s seat positioning on the driver’s door. which will enhance driver mobility out of and into the 4. Within five seconds, press and release MEMORY vehicle. button 1 on the driver’s door. There are two possible Easy Entry/Exit adjustments 5. Within five seconds, press and release the UNLOCK available: button on the RKE transmitter.
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE driving position when the key is placed into the TO OPEN AND CLOSE THE HOOD ignition, and turned out of the LOCK position toward To open the hood, two latches must be released. the ACC/ON position. 1. Pull the release lever located below the instrument The Easy Entry/Exit feature will be automatically dis- panel and in front of the driver’s door. abled if the seat is already positioned closer than 0.9 in (23 mm) forward of the rear stop.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Reach under the hood, move safety latch to the left and lift the hood. 143 CAUTION! To prevent possible damage, do not slam the hood to close it. Use a firm downward push at the center of the hood to ensure that both latches engage. 3 WARNING! Be sure the hood is fully latched before driving your vehicle. If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To turn on the headlights, rotate the headlight LIGHTS switch clockwise. When the headlight switch is Headlight Switch on the parking lights, taillights, license plate The headlight switch is located on the left side of the light and instrument panel lights are also instrument panel, next to the steering wheel. The headturned on.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 Headlights On Automatically With Wipers If your vehicle is equipped with Automatic Headlights, it Do not use abrasive cleaning components, solvents, also has this customer-programmable feature. When steel wool or other abrasive materials to clean the your headlights are in the automatic mode and the engine is running, they will automatically turn on when lenses. the wiper system is on.
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: When your headlights come on during the To Activate daytime, the instrument panel lights will automatically 1. Enable the Automatic High Beams. Refer to “Elecdim to the lower nighttime intensity. Refer to “Lights” in tronic Vehicle Information Center (EVIC)/Customerthis section for further information. Programmable Features” in “Understanding Your InstruSmartBeam™ — If Equipped ment Panel” for further information.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 2. Push back on the multifunction lever once again to Automatic Headlight Leveling — HID Headlights reactivate the system. Only This feature prevents the headlights from interfering NOTE: Broken, muddy, or obstructed headlights and with the vision of oncoming drivers. Headlight leveling taillights of vehicles in the field of view will cause automatically adjusts the height of the headlight beam in headlights to remain on longer (closer to the vehicle).
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The headlight delay time is programmable on vehicles equipped with an Electronic Vehicle Information Center (EVIC). Refer to “Electronic Vehicle Information Center (EVIC)/Customer-Programmable Features” in “Understanding Your Instrument Panel” for further information. Parking Lights and Panel Lights To turn on the parking lights and instrument panel lights, rotate the headlight switch clockwise.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 to its farthest position up until you hear a click. This Interior Lights Courtesy and dome lights are turned on when the front feature is termed the “Parade” mode and is useful when doors are opened, when the dimmer control (rotating headlights are required during the day.
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Battery saver mode is cancelled if the ignition is Lights-on Reminder If the headlights, parking lights, or cargo lights are left on ON. after the ignition is turned OFF, a chime will sound when Front Map/Reading Lights the driver’s door is opened. The front map/reading lights are mounted in the overBattery Saver head console. To protect the life of your vehicle’s battery, load shedding is provided for both the interior and exterior lights.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Each light can be turned on by pressing a switch on either side of the console. These buttons are backlit for night time visibility. To turn the lights off, press the switch a second time. The lights will also turn on when the UNLOCK button on the Remote Keyless Entry (RKE) is pressed. Ambient Light The overhead console is equipped with an ambient light feature. This light casts illumination for improved visibility of the floor center console and PRNDL area.
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Multifunction Lever Turn Signals The multifunction lever is located on the left side of the Move the multifunction lever up or down and the arrows steering column. on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights. NOTE: If either light remains on and does not flash, or there is a very fast flash rate, check for a defective outside light bulb.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 High/Low Beam Switch Push the multifunction lever toward the instrument panel to switch the headlights to high beam. Pulling the multifunction back toward the steering wheel will turn the low beams back on, or shut the high beams off. WINDSHIELD WIPERS AND WASHERS The windshield wiper/washer control lever is located on the left side of the steering column. The front wipers are operated by rotating a switch, located on the end of the lever.
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Windshield Wiper Operation Rotate the end of the lever to one of the first four detent positions for intermittent settings, the fifth detent for low wiper operation and the sixth detent for high wiper operation. CAUTION! Always remove any buildup of snow that prevents the windshield wiper blades from returning to the “park” position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 Windshield Washer Operation To use the washer, push on the end of the lever (toward the steering wheel) and hold while spray is desired. If the lever is pushed while in the intermittent setting, the wipers will turn on and operate for several wipe cycles after the end of the lever is released, and then resume the intermittent interval previously selected.
156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If the end of the lever is pushed while the wipers are in the off position, the wipers will operate for several wipe cycles, then turn off. WARNING! Sudden loss of visibility through the windshield could lead to a collision. You might not see other vehicles or other obstacles. To avoid sudden icing of the windshield during freezing weather, warm the windshield with the defroster before and during windshield washer use.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 Sensing feature to be turned off. Refer to “Electronic The sensitivity of the system can be adjusted with the Vehicle Information Center (EVIC)/Personal Settings multifunction lever. Wiper delay position 1 is the least (Customer-Programmable Features)” in “Understandsensitive, and wiper delay position 4 is the most sensiing Your Instrument Panel” for further information. tive. Setting 3 should be used for normal rain conditions.
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE TILT/TELESCOPING STEERING COLUMN This feature allows you to tilt the steering column upward or downward. It also allows you to lengthen or shorten the steering column. The tilt/telescoping lever is located below the steering wheel at the end of the steering column. To unlock the steering column, push the lever downward (toward the floor). To tilt the steering column, move the steering wheel upward or downward as desired.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE POWER TILT/TELESCOPING STEERING COLUMN — IF EQUIPPED This feature allows you to tilt the steering column upward or downward. It also allows you to lengthen or shorten the steering column. The power tilt/telescoping steering column lever is located below the multifunction lever on the steering column. Power Tilt/Telescoping Steering 159 To tilt the steering column, move the lever up or down as desired.
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Do not adjust the steering column while driving. Adjusting the steering column while driving or driving with the steering column unlocked, could cause the driver to lose control of the vehicle. Be sure the steering column is locked before driving your vehicle. Failure to follow this warning may result in serious injury or death.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! The Electronic Speed Control buttons are located on the right side of the steering wheel. • Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion, or other physical conditions must exercise care when using the steering wheel heater. It may cause burns even at low temperatures, especially if used for long periods.
162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE System can be reactivated by pushing the Electronic Speed Control ON/OFF button and resetting the desired vehicle set speed. To Activate Push the ON/OFF button. The Cruise Indicator Light in the instrument cluster will illuminate. To turn the system off, push the ON/OFF button a second time. The Cruise Indicator Light will turn off. The system should be turned off when not in use.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Set A Desired Speed Turn the Electronic Speed Control ON. When the vehicle has reached the desired speed, press the SET (-) button and release. Release the accelerator and the vehicle will operate at the selected speed. 163 To Vary The Speed Setting When the Electronic Speed Control is set, you can increase speed by pushing the RES (+) button.
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Accelerate For Passing Press the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. Using Electronic Speed Control On Hills The transmission may downshift on hills to maintain the vehicle set speed. WARNING! Electronic Speed Control can be dangerous where the system cannot maintain a constant speed. Your vehicle could go too fast for the conditions, and you could lose control and have a collision.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ACC will allow you to keep cruise control engaged in light to moderate traffic conditions without the constant need to reset your cruise control. ACC utilizes a radar sensor designed to detect a vehicle directly ahead of you. NOTE: • If the sensor does not detect a vehicle ahead of you, ACC will maintain a fixed set speed.
166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! (Continued) WARNING! − Cannot take street, traffic, and weather conditions into account, and may be limited upon adverse sight distance conditions. − Does not predict the lane curvature or the movement of preceding vehicles and will not compensate for such changes. − Does not always fully recognize complex driving conditions, which can result in wrong or missing distance warnings.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 The Cruise Control system has two control modes: • Adaptive Cruise Control mode for maintaining an appropriate distance between vehicles. • Normal (fixed speed) cruise control mode for cruising at a constant preset speed. For additional information, refer to “Normal (Fixed Speed) Cruise Control Mode” in this section. Note: The system will not react to preceding vehicles. Always be aware of the mode selected.
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Any chassis/suspension modifications to the NOTE: You cannot enable ACC under the following vehicle will effect the performance of the Adaptive Cruise conditions: Control. • When in Four-Wheel Drive Low. Activating Adaptive Cruise Control (ACC) • When you apply the brakes. You can only activate ACC if the vehicle speed is above 25 mph (40 km/h). • When the parking brake is set.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 To turn the system OFF, push and release the ON/OFF To Activate Push and release the ON/OFF button. The ACC menu in button again. At this time, the system will turn off and the EVIC displays “Adaptive Cruise Ready.” the EVIC will display “Adaptive Cruise Control Off.” WARNING! Leaving the Adaptive Cruise Control (ACC) system on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want.
170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Remove your foot from the accelerator pedal. If you do To Set A Desired ACC Speed When the vehicle reaches the speed desired, push the not, the vehicle may continue to accelerate beyond the set SET - button and release. The EVIC will display the set speed. If this occurs: speed. • The message “DRIVER OVERRIDE” will display in the EVIC. • The system will not be controlling the distance between your vehicle and the vehicle ahead.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 To Cancel The system will disable ACC without erasing the memory if: • You softly tap the brake pedal. • You depress the brake pedal. • You press the CANCEL switch. • An Anti-Lock Brake System (ABS) event occurs. • A Trailer Sway Control (TSC) event occurs. • If the transmission is shifted into Neutral. Driver Override • The Electronic Stability Control/Traction Control System (ESC/TCS) activates.
172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: If ACC is resumed or set with the ESC/TCS is To Turn Off The system will turn off and erase the set speed in off, ESC will automatically be re-engaged. memory if: • You push and release the ON/OFF button. • You turn OFF the ignition. • You switch off ESC. • You switch to Four-Wheel Drive Low. To Resume Speed Press the RES + button and release. Then remove your foot from the accelerator pedal. The EVIC will display the last set speed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! The Resume function should only be used if traffic and road conditions permit. Resuming a set speed that is too high or too low for prevailing traffic and road conditions could cause the vehicle to accelerate or decelerate too sharply for safe operation. This could cause a collision and/or serious injury. 173 While ACC is set, the set speed can be decreased by pressing and holding the SET - button.
174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The ACC system maintains set speed when driving up hill and down hill. However, a slight speed change on moderate hills is normal. In addition, downshifting may occur while climbing uphill or descending downhill. This is normal operation and necessary to maintain set speed. Setting The Following Distance In ACC The specified following distance for ACC can be set by varying the distance setting between 3 (long), 2 (medium), and 1 (short).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175 3 Distance Setting 2 Distance Setting 1
176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To change the distance setting, press the Distance button • The distance setting is changed. and release. Each time the button is pressed, the distance • The system disengages. (Refer to the information on setting adjusts between long, medium, and short. ACC Activation). If there is no vehicle ahead, the vehicle will maintain the The maximum braking applied by ACC is limited; howset speed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177 Press the MENU button (located on the steering wheel) repeatedly until one of the following displays in the EVIC: Menu Button Adaptive Cruise Control Off − When ACC is deactivated, the display will read “Adaptive Cruise Control Off.” Adaptive Cruise Control Ready Brake Alert − When ACC is activated but the vehicle speed setting has not been selected, the display will read “Adaptive Cruise Control Ready.
178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The set speed will continue to display in place of the odometer reading when changing the EVIC display while ACC is set. • Distance Setting Change • System Cancel • Acquisition/Loss of Target • Driver Override • System Off • ACC Proximity Warning • ACC Unavailable Warning The EVIC will return to the last display selected after five seconds of no ACC display activity.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179 system may also become temporarily blinded due to Control is still available. For additional information refer obstructions, such as mud, dirt or ice. In these cases, the to “Normal (Fixed Speed) Cruise Control Mode” in this EVIC will display “Clean Radar Sensor In Front Of section. Vehicle” and the system will deactivate. If weather conditions are not a factor, the driver should examine the sensor. It may require cleaning or removal of an obstruction.
180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Do not attach or install any accessories near the sensor, To remove the sensor follow these instructions: including transparent material or aftermarket grilles. 1. Unplug the connector by depressing the two tabs on Doing so could cause an ACC system failure or the connector and pulling it out. Do not pull by the malfunction. wiring or using any tools to remove the connector. When the condition that deactivated the system is no 2.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: When the sensor is removed, Adaptive Cruise Control, Normal Cruise Control, and Forward Collision Warning will not be available. The cluster will display the warning “ACC/FCW Unavailable - Service Radar Sensor.” To reinstall the sensor and bracket assembly reverse the process above. The fastener torque required to assembly the bracket back to the beam is 6.6 ft lbs (9 Nm).
182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Precautions While Driving With ACC In certain driving situations, ACC may have detection issues. In these cases, ACC may brake late or unexpectedly. The driver needs to stay alert and may need to intervene. Adding A Trailer Hitch The weight of a trailer hitch may affect the performance of ACC. If there is a noticeable change in performance following the installation of a hitch, such as reduced detection range, please see your authorized dealer for service.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 183 Using ACC On Hills When driving on hills, ACC may not detect a vehicle in your lane. Depending on the speed, vehicle load, traffic conditions, and the steepness of the hills, ACC performance may be limited. 3 ACC may occasionally provide braking and/or a driver alert that you consider unnecessary. This may be the system’s response to signs, guardrails, and other stationary objects in a curve. This may also occur at the base of steep hills.
184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Lane Changing ACC will not detect a vehicle until it is completely in the lane in which you are traveling. In the illustration shown, ACC has not yet detected the vehicle changing lanes and it may not detect the vehicle until it’s too late for the ACC system to take action. ACC will not detect a vehicle until it is completely in the lane. There will not be sufficient distance to the lane-changing vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 185 3 Stationary Objects And Vehicles General Information ACC does not react to stationary objects and stationary FCC Requirements For Vehicular Radar Systems vehicles. For example, ACC will not react in situations Classification Specifications: where the vehicle you are following exits your lane and 47 C.F.R. Part 15 the vehicle ahead is stopped in your lane. Always be 47 C.F.R Part 15.515 attentive and ready to apply the brakes if necessary.
186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Normal (Fixed Speed) Cruise Control Mode In addition to Adaptive Cruise Control mode, a normal (fixed speed) Cruise Control mode is available for cruising at fixed speeds. The normal Cruise Control mode is designed to maintain a set cruising speed without requiring the driver to operate the accelerator. Cruise Control can only be operated if the vehicle speed is above 25 mph (40 km/h).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 187 To Vary The Speed Setting There are two ways to change the set speed: To Resume Press the RES + button and then remove your foot from the accelerator pedal. The EVIC will display the last set • Use the accelerator pedal to adjust the vehicle to the speed. desired speed and press the SET - button.
188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Forward Collision Warning — If Equipped Forward Collision Warning (FCW) warns the driver of a potential collision with the vehicle in front of you and prompts the driver to take action in order to avoid the collision. FCW monitors the information from the forward looking sensor as well as the Electronic Brake Controller (EBC), wheel speed sensors, i.e., to calculate a probable rear-end collision.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Forward Collision Warning (FCW) is not intended to avoid a collision on its own. The driver has the responsibility to avoid a collision by controlling the vehicle via braking and steering. Failure to follow this warning could lead to serious injury or death. 189 The default status of FCW is the “Far” setting, this allows the system to warn you of a possible collision with the vehicle in front of you when you are farther away.
190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Changing the FCW status to the “Near” setting, allows Changing the FCW status to “Off” prevents the system the system to warn you of a possible collision with the from warning you of a possible collision with the vehicle vehicle in front of you when you are much closer. This in front of you. setting provides less reaction time than the “Far” setting, which allows for a more dynamic driving experience.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 191 • FCW will not react to irrelevant objects such as overhead objects, ground reflections, objects not in the path of the car, stationary objects that are far away, oncoming traffic, or leading vehicles with the same or higher rate of speed. • FCW will be disabled like ACC below with the unavailable screens.
192 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Service FCW Warning If the system turns off, and the EVIC displays “ACC/ FCW Unavailable Service Radar Sensor”, it indicates there is an internal system fault. Although the vehicle is still drivable under normal conditions, have the system checked by an authorized dealer.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ParkSense姞 Sensors The four ParkSense威 sensors, located in the rear fascia/ bumper, monitor the area behind the vehicle that is within the sensors’ field of view. The sensors can detect obstacles from approximately 12 in (30 cm) up to 79 in (200 cm) from the rear fascia/bumper in the horizontal direction, depending on the location, type and orientation of the obstacle.
194 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ParkSense姞 Display When the vehicle is in REVERSE, the warning display will turn ON indicating the system status.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 195 The system will indicate a detected obstacle by showing three solid arcs and will produce a one-half second tone. As the vehicle moves closer to the object the EVIC display will show fewer arcs and the sound tone will change from slow, to fast, to continuous.
196 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The vehicle is close to the obstacle when the EVIC display shows one flashing arc and sounds a continuous tone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Distance (in/cm) Audible Alert Chime Display Message Greater than 79 in (200 cm) None Park Assist ON Arcs None Radio Mute No WARNING ALERTS 79-39 in 39-25 in (200-100 cm) (100-65 cm) Single 1/2 Slow Second Tone Warning Object Warning Object Detected Detected 3 Solid 3 Slow (Continuous) Flashing Yes Yes NOTE: ParkSense威 will MUTE the radio, if on, when the system is sounding an audio tone.
198 UNDERSTANDING THE FEATURES OF YOUR VEHICLE approximately five seconds. Refer to “Electronic Vehicle Information Center (EVIC)” in “Understanding Your Instrument Panel” for further information. When the shift lever is moved to REVERSE and the system is disabled, the EVIC will display the “PARK ASSIST OFF” message for as long as the vehicle is in REVERSE. The ParkSense威 switch LED will be ON when ParkSense威 is disabled or defective. The ParkSense威 switch LED will be OFF when the system is enabled.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 199 If “SERVICE PARK ASSIST SYSTEM” appears in the • When you turn ParkSense威 off, the instrument cluster EVIC, see your authorized dealer. will display “PARK ASSIST OFF.” Furthermore, once you turn ParkSense威 off, it remains off until you turn Cleaning the ParkSense姞 System it on again, even if you cycle the ignition key. Clean the ParkSense威 sensors with water, car wash soap and a soft cloth. Do not use rough or hard cloths.
200 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Objects such as bicycle carriers, trailer hitches, etc., must not be placed within 12 in (30 cm) from the rear fascia/bumper while driving the vehicle. Failure to do so can result in the system misinterpreting a close object as a sensor problem, causing the “SERVICE PARK ASSIST SYSTEM” message to be displayed in the instrument cluster.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 201 WARNING! WARNING! (Continued) • Drivers must be careful when backing up even when using the ParkSense威 Rear Park Assist System. Always check carefully behind your vehicle, look behind you, and be sure to check for pedestrians, animals, other vehicles, obstructions, and blind spots before backing up. You are responsible for safety and must continue to pay attention to your surroundings. Failure to do so can result in serious injury or death.
202 UNDERSTANDING THE FEATURES OF YOUR VEHICLE PARKVIEW姞 REAR BACK UP CAMERA — IF EQUIPPED Your vehicle may be equipped with the ParkView威 Rear Back Up Camera that allows you to see an on-screen image of the rear surroundings of your vehicle whenever the shift lever is put into REVERSE. The image will be displayed on the Navigation/Multimedia radio display screen along with a caution note to “check entire surroundings” across the top of the screen. After five seconds this note will disappear.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! 203 CAUTION! (Continued) Drivers must be careful when backing up even when using the ParkView威 Rear Back Up Camera. Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, obstructions, or blind spots before backing up. You are responsible for the safety of your surroundings and must continue to pay attention while backing up. Failure to do so can result in serious injury or death.
204 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Enable or disable the rear camera feature by selecting “enable rear camera in reverse” soft key. 5. Press the “save” soft key. Turning ParkView姞 On or Off — Without Navigation/Multimedia Radio 1. Press the “menu” hard key. 2. Select “system setup” soft key. 3. Enable or disable the rear camera feature by selecting “enable rear camera in reverse” soft key. OVERHEAD CONSOLE The overhead console contains courtesy/reading lights and storage for sunglasses.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 205 Sunglasses Storage At the rear of the console a compartment is provided for the storage of a pair of sunglasses. The storage compartment access is a “push/push” design. Push the chrome pad on the door to open. Push the chrome pad on the door to close.
206 UNDERSTANDING THE FEATURES OF YOUR VEHICLE GARAGE DOOR OPENER — IF EQUIPPED HomeLink威 replaces up to three remote controls (handheld transmitters) that operate devices such as garage door openers, motorized gates, lighting or home security systems. The HomeLink威 unit operates off your vehicle’s battery. The HomeLink威 buttons that are located in the overhead console designate the three different HomeLink威 channels.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Your motorized door or gate will open and close while you are training the universal transceiver. Do not train the transceiver if people, pets or other objects are in the path of the door or gate. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by Federal safety standards. This includes most garage door opener models manufactured after 1982.
208 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Place the handheld transmitter 1 to 3 in (3 to 8 cm) away • After training a HomeLink威 channel, if the garage from the HomeLink威 button you wish to program while door does not operate with HomeLink威 and the gakeeping the indicator light in view. rage door opener was manufactured after 1995, the garage door opener may have a rolling code. If so, 3.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 209 This can usually be found where the hanging antenna 1. Firmly press and release the LEARN or TRAINING wire is attached to the garage door opener motor. It is button. The name and color of the button may vary by NOT the button normally used to open and close the manufacturer. door. NOTE: You have 30 seconds in which to initiate the next step after the LEARN button has been pressed. 2.
210 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Gate Operator/Canadian Programming Canadian radio frequency laws require transmitter signals to time-out (or quit) after several seconds of transmission – which may not be long enough for HomeLink威 to pick up the signal during programming. Similar to this Canadian law, some U.S. gate operators are designed to time-out in the same manner. If you unplugged the device for training, plug it back in at this time.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 211 3. Without releasing the button, proceed with Program- • Press the LEARN button on the Garage Door Opener ming HomeLink威 Step 2 and follow all remaining steps. to complete the training for a Rolling Code. Security • Did you unplug the device for training, and remember to plug it back in? It is advised to erase all channels before you sell or turn in your vehicle.
212 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: POWER SUNROOF — IF EQUIPPED • The transmitter has been tested and it complies with The power sunroof switch is located between the sun FCC and IC rules. Changes or modifications not visors on the overhead console. expressly approved by the party responsible for compliance could void the user’s authority to operate the device. • The term IC before the certification/registration number only signifies that Industry Canada technical specifications were met.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Never leave children in a vehicle with the key in the ignition switch. Occupants, particularly unattended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death. • In a collision, there is a greater risk of being thrown from a vehicle with an open sunroof. You could also be seriously injured or killed.
214 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: If three consecutive sunroof close attempts re- Sunshade Operation sult in Pinch Protect reversals, the fourth close attempt The sunshade can be opened manually. However, the will be a Manual Close movement with Pinch Protect sunshade will open automatically as the sunroof opens. disabled. NOTE: The sunshade cannot be closed if the sunroof is Pinch Protect Override open. If a known obstruction (ice, debris, etc.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 215 Sunroof Maintenance Use only a nonabrasive cleaner and a soft cloth to clean the glass panel. Ignition OFF Operation The power sunroof switches remain active for up approximately ten minutes after the ignition switch has been turned OFF. Opening either front door will cancel this feature. COMMAND VIEW SUNROOF WITH POWER SHADE — IF EQUIPPED The command view sunroof switch is located to the left between the sun visors on the overhead console.
216 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Never leave children in a vehicle with the key in the ignition switch. Occupants, particularly unattended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death. • In a collision, there is a greater risk of being thrown from a vehicle with an open sunroof. You could also be seriously injured or killed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Closing Sunroof – Express Press the sunroof switch forward for less than one second and release, and the sunroof glass will automatically close from any position, then stop. This is called “Express Close”. During Express Close operation, any sunroof switch press or shade switch press will stop the sunroof. 217 Closing Power Shade – Express Press the shade switch forward for less than one second and release, and the shade will automatically close, then stop.
218 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Pinch Protect Feature This feature will detect an obstruction in the opening of the sunroof or the shade during any close operation. If an obstruction is detected, the sunroof or shade will automatically reverse direction to release the obstruction. If this occurs, remove the obstruction and then press the sunroof or shade switch forward to complete the desired close motion.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 219 together to minimize the buffeting. If the buffeting occurs Sunroof Fully Closed with the sunroof open, adjust the sunroof opening to Press the switch forward and release to ensure that the sunroof is fully closed. minimize the buffeting or open any window. Sunroof Maintenance ELECTRICAL POWER OUTLETS Use only a non-abrasive cleaner and a soft cloth to clean Your vehicle is equipped with 12 Volt (13 Amp) power the glass panel.
220 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • To ensure proper operation a MOPAR威 knob and element must be used. • Do not exceed the maximum power of 160 Watts (13 Amps) at 12 Volts. If the 160 Watt (13 Amp) power rating is exceeded the fuse protecting the system will need to be replaced. The front power outlet is located inside the storage area on the center stack of the instrument panel. Push inward on the storage lid to open the compartment and gain access to this power outlet.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 221 3 Center Console Outlet Rear Power Outlet The rear power outlet is located in the right rear cargo area. WARNING! To avoid serious injury or death: • Only devices designed for use in this type of outlet should be inserted into any 12 Volt outlet.
222 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! (Continued) CAUTION! (Continued) • Do not touch with wet hands. • Close the lid when not in use and while driving the vehicle. • If this outlet is mishandled, it may cause an electric shock and failure. • Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.) will degrade the battery even more quickly. Only use these intermittently and with greater caution.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 223 150 Watts. Certain high-end video games, such as Play- the electrical device has been removed from the outlet the station3 and XBox360 will exceed this power limit, as will inverter should automatically reset. If the power rating exceeds approximately 170 Watts, the power inverter most power tools. may have to be reset manually. To reset the inverter manually press the power inverter button OFF and ON.
224 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! To avoid serious injury or death: • Do not use a three-prong adaptor. • Do not insert any objects into the receptacles. • Do not touch with wet hands. • Close the lid when not in use. • If this outlet is mishandled it may cause an electric shock and failure. CUPHOLDERS There are two cupholders for the front seat passengers located in the center console.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 225 There are two cupholders for the rear seat passengers STORAGE located in the fold-down center armrest. Glove Compartment The glove compartment is located on the right side of the instrument panel.
226 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To open the glove compartment, pull outward on the Door Storage Large storage areas are built into the door panels for easy latch and lower the glove box door. access.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 227 To open the upper storage compartment, pull upward on Center Console The center console contains both an upper and a lower the small latch located on the lid. storage area.
228 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Lift upward on the larger of the latches to access the needed. The flashlight features two bright LED light bulbs and is powered by rechargeable lithium batteries lower storage compartment. that recharge when snapped back into place. Press in on the flashlight to release it. Lower Storage Compartment CARGO AREA FEATURES Rechargeable Flashlight The rechargeable flashlight is mounted on the left side of the cargo area.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 229 To operate the flashlight, press the switch once for high, Cargo Storage Bins There are four removable storage bins located in the rear twice for low, and a third time to return to off. cargo area. There are two storage bins located on either side of the cargo area.
230 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Two additional storage bins are located under the load floor. To access the lower storage bins, raise the load floor and attach the tether hook (attached to the bottom of the load floor) to the liftgate opening.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 231 Retractable Cargo Area Cover — If Equipped NOTE: The purpose of this cover is for privacy, not to secure loads. It will not prevent cargo from shifting or protect passengers from loose cargo. To cover the cargo area: 3 1. Grasp the cover at the center handle. Pull it over the cargo area. 2. Insert the pins on the ends of the cover into the slots in the pillar trim cover. 3. The liftgate may be opened with the cargo cover in place.
232 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! In a collision, a loose cargo cover in the vehicle could cause injury. It could fly around in a sudden stop and strike someone in the vehicle. Do not store the cargo cover on the cargo floor or in the passenger compartment. Remove the cover from the vehicle when taken from its mounting. Do not store it in the vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 233 WARNING! WARNING! (Continued) • To help protect against personal injury, passengers should not be seated in the rear cargo area. The rear cargo space is intended for load carrying purposes only, not for passengers, who should sit in seats and use seat belts. • Cargo tie-down hooks are not safe anchors for a child seat tether strap. In a sudden stop or accident, a hook could pull loose and allow the child seat to come loose. A child could be badly injured.
234 UNDERSTANDING THE FEATURES OF YOUR VEHICLE REAR WINDOW FEATURES Rear Window Wiper/Washer The rear wiper/washer is controlled by a rotary switch located on the control lever. The control lever is located on the left side of the steering column. Rotate the center portion of the lever upward to the first detent for intermittent operation and to the second detent for continuous rear wiper operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 235 If the rear wiper is operating when the ignition is turned NOTE: To prevent excessive battery drain, use the rear OFF, the wiper will automatically return to the “park” window defroster only when the engine is operating. position. If the liftgate flipper glass is open, the rear window wiper/washer functionality is interrupted and the wiper stops at that “park” position.
236 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ROOF LUGGAGE RACK — IF EQUIPPED The crossbars and siderails are designed to carry the weight on vehicles equipped with a luggage rack. The load must not exceed 150 lbs (68 kg), and should be uniformly distributed over the luggage rack crossbars. rack frame. Once the crossbar is in the desired position, retighten the with the wrench to lock the crossbar into position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 237 CAUTION! CAUTION! (Continued) • To prevent damage to the roof of your vehicle, do not carry any loads on the roof rack without the crossbars installed. The load should be secured and placed on top of the crossbars, not directly on the roof. If it is necessary to place the load on the roof, place a blanket or some other protection between the load and the roof surface.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 Instrument Panel Features . . . . . . . . . . . . . . . 242 ▫ Engine Oil Change Indicator System . . . . . . . 268 䡵 Instrument Cluster . . . . . . . . . . . . . . . . . . . . 243 ▫ Fuel Economy . . . . . . . . . . . . . . . . . . . . . . 268 䡵 Instrument Cluster Descriptions . . . . . . . . . . . 244 ▫ Vehicle Speed . . . . . . . . . . . . . . . . . . . . . . . 270 䡵 Electronic Vehicle Information Center (EVIC) . . 254 ▫ Trip Info . . . . . . . . . . .
240 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Compass / Temperature Display . . . . . . . . . 273 ▫ Operation Instructions - Auxiliary Mode . . . . 293 ▫ Customer-Programmable Features (System Setup) . . . . . . . . . . . . . . . . . . . . . . 276 䡵 Media Center 130 With Satellite Radio (Sales Code RES+RSC). . . . . . . . . . . . . . . . . . . 293 䡵 Media Center 730N/430/430N (RHR/RER/ RBZ/RHB) CD/DVD/HDD/NAV — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 241 䡵 iPod威/MP3 Control — If Equipped . . . . . . . . . 309 䡵 Steering Wheel Audio Controls . . . . . . . . . . . . 318 ▫ Connecting The iPod威 Or External USB Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . 310 ▫ Using This Feature . . . . . . . . . . . . . . . . . . . 311 ▫ Controlling The iPod威 Or External USB Device Using Radio Buttons . . . . . . . . . . . . . 311 ▫ Play Mode . . . . . . . . . . . . . . . . . . . . . . . . .
242 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT PANEL FEATURES 1 2 3 4 — Air Outlet — Instrument Cluster — Radio — Glove Compartment 5 6 7 8 — — — — Climate Controls Lower Switch Bank Storage Bin Ignition Switch 9 — Fuel Door Release 10 — Headlight Switch 11 — Hood Release
UNDERSTANDING YOUR INSTRUMENT PANEL 243 INSTRUMENT CLUSTER 4
244 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTIONS the ON/RUN position before engine start. If the bulb does not come on when turning the key from OFF to ON/RUN, have the condition checked promptly. 1. Tachometer Indicates the engine speed in revolutions per minute Certain conditions such as a loose or missing gas cap, (RPM x 1000). poor fuel quality, etc., may illuminate the light after 2. Airbag Warning Light engine start.
UNDERSTANDING YOUR INSTRUMENT PANEL WARNING! A malfunctioning catalytic converter, as referenced above, can reach higher temperatures than in normal operating conditions. This can cause a fire if you drive slowly or park over flammable substances such as dry plants or wood or cardboard, etc. This could result in death or serious injury to the driver, occupants or others. 245 system.
246 UNDERSTANDING YOUR INSTRUMENT PANEL 9. Hill Descent Control Indicator Light — If Equipped 5. TOW/HAUL Indicator Light — If Equipped The symbol indicates the status of the Hill This light will illuminate when the TOW/ Decent Control (HDC) feature. The lamp will HAUL button has been selected. The TOW/ be on solid when HDC is armed. HDC can only HAUL button is located in the center of the be armed when the transfer case is in the “4WD instrument panel (below the climate controls).
UNDERSTANDING YOUR INSTRUMENT PANEL as it was before the repair or service. If s/he cannot do so, then the odometer must be set at zero, and a sticker must be placed in the door jamb stating what the mileage was before the repair or service. It is a good idea for you to make a record of the odometer reading before the repair/ service, so that you can be sure that it is properly reset, or that the door jamb sticker is accurate if the odometer must be reset at zero.
248 UNDERSTANDING YOUR INSTRUMENT PANEL Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale. Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is combined with the low tire pressure telltale.
UNDERSTANDING YOUR INSTRUMENT PANEL 249 14. Brake Warning Light 12. Position Light Indicator — If Equipped This light monitors various brake functions, This indicator will illuminate when the park including brake fluid level and parking brake lights or headlights are turned on. application. If the brake light turns on, it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with 13.
250 UNDERSTANDING YOUR INSTRUMENT PANEL The dual brake system provides a reserve braking capacity in the event of a failure to a portion of the hydraulic system. A leak in either half of the dual brake system is indicated by the Brake Warning Light, which will turn on when the brake fluid level in the master cylinder has dropped below a specified level. The light will remain on until the cause is corrected.
UNDERSTANDING YOUR INSTRUMENT PANEL 251 The light also will turn on when the parking brake is brakes. If the ABS light does not turn on when the applied with the ignition switch in the ON/RUN posi- ignition switch is turned to the ON/RUN position, have the light inspected by an authorized dealer. tion. NOTE: This light shows only that the parking brake is 16. 4 LOW applied. It does not show the degree of brake application. This light alerts the driver that the vehicle is in the four-wheel drive LOW mode.
252 UNDERSTANDING YOUR INSTRUMENT PANEL 22. Electronic Vehicle Information Center (EVIC) Red 18. Fuel Door Reminder The fuel pump symbol points to the side of the Telltale Area This area will display the EVIC reconfigurable red tellvehicle where the fuel door is located. tales. For further information refer to “Electronic vehicle Information Center (EVIC)”. 19. Fuel Gauge 23.
UNDERSTANDING YOUR INSTRUMENT PANEL 25. Temperature Gauge The temperature gauge shows engine coolant temperature. Any reading within the normal range indicates that the engine cooling system is operating satisfactorily. The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer. It should not be allowed to exceed the upper limits of the normal operating range.
254 UNDERSTANDING YOUR INSTRUMENT PANEL The EVIC consists of the following: ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) • System Status The Electronic Vehicle Information Center (EVIC) features a driver-interactive display that is located in the • Vehicle Information Warning Message Displays instrument cluster.
UNDERSTANDING YOUR INSTRUMENT PANEL 255 The system allows the driver to select information by UP Button pressing the following buttons mounted on the steering Press and release the UP button to scroll upwheel: ward through the main menus (Fuel Economy, Vehicle Info, Tire PSI, Cruise, Messages, Units, System Setup) and sub menus. DOWN Button Press and release the DOWN button to scroll downward through the main menus and sub menus.
256 UNDERSTANDING YOUR INSTRUMENT PANEL BACK Button • Right front turn signal lamp out Press the BACK button to scroll back to a • Left rear turn signal lamp out previous menu or sub menu.
UNDERSTANDING YOUR INSTRUMENT PANEL 257 • Adaptive Cruise Off — When the Adaptive Cruise • Driver Override — If you apply the accelerator after Control (ACC) system is turned off. Refer to “Adapsetting the desired speed in the ACC system. Refer to tive Cruise Control (ACC)” in “Understanding The “Adaptive Cruise Control (ACC)” in “Understanding Features Of Your Vehicle” (if equipped). The Features Of Your Vehicle” (if equipped). • ACC Ready — When the ACC system is activated.
258 UNDERSTANDING YOUR INSTRUMENT PANEL • Clean Radar Sensor in the Front of Vehicle — If the • Oil change due ACC system deactivates due to performance limiting • Key in ignition conditions. Refer to “Adaptive Cruise Control (ACC)” in “Understanding The Features Of Your Vehicle” (if • Lights on equipped). • Key in Ignition Lights On • ACC/FCW Unavailable Vehicle System Error — If the • Ignition or Accessory On ACC system turns off due to a temporary malfunction that limits functionality.
UNDERSTANDING YOUR INSTRUMENT PANEL • Remote start disabled — System fault • Function currently unavailable — Power Liftgate • Remote start disabled — Turn key • Unlock to operate — Power Liftgate • Remote start active — Key to Run • Put in Park to operate — Power Liftgate • Memory 1 profile set • Automatic high beams on • Memory 2 profile set • Automatic high beams off • Memory system unavailable — Not in Park • Service Four Wheel Drive System • Memory system unavailable — Seatbelt buckled •
260 UNDERSTANDING YOUR INSTRUMENT PANEL • Sport Not Available in 4 Low 4 High is Required • Rock Not Available in 4 Low 4 High is Required • Off Road Ride Height Level 1 — This message is displayed (for 5 seconds) when the vehicle has achieved the Off Road Height Level 1.
UNDERSTANDING YOUR INSTRUMENT PANEL 261 • Service Air Suspension System — This is displayed • Air Suspension System Cooling Down – Please Wait — when a fault has occurred in the system. The system This message is displayed if the compressor temperawill have limited operation at that point. ture level is too high. Level control is suspended until the compressor has cooled down.
262 UNDERSTANDING YOUR INSTRUMENT PANEL EVIC White Telltale Lights • Electronic Speed Control SET This area will show reconfigurable white caution tellThis light will turn on when the electronic tales. These telltales include: speed control is SET. For further information, refer to “Electronic Speed Control” in “Under• Shift Lever Status standing The Features Of Your Vehicle”. The shift lever status “P,R,N,D,L,5,4,3,2,1” are displayed indicating the shift lever position.
UNDERSTANDING YOUR INSTRUMENT PANEL • Power Steering System Over Temperature — If Equipped If the “POWER STEERING SYSTEM OVER TEMP” message and a icon are displayed on the EVIC screen, it indicates that extreme steering maneuvers may have occurred, which caused an over temperature condition in the power steering system. You will lose power steering assistance momentarily until the over temperature condition no longer exists. Once driving conditions are safe, then pull over and let vehicle idle.
264 UNDERSTANDING YOUR INSTRUMENT PANEL • Air Suspension Down The air suspension down telltale will illuminate when the air suspension is in use. For further information, refer to “Starting And Operating”. to turn off the message. If the problem continues, the message will appear the next time the vehicle is started. A loose, improperly installed, or damaged fuel filler cap may also turn on the Malfunction Indicator Light (MIL).
UNDERSTANDING YOUR INSTRUMENT PANEL 265 EVIC Red Telltale Lights • Oil Pressure Warning Light This area will show reconfigurable red telltales. These This light indicates low engine oil pressure. The telltales include: light should turn on momentarily when the engine is started. If the light turns on while driving, stop the • Door Ajar vehicle and shut off the engine as soon as possible.
266 UNDERSTANDING YOUR INSTRUMENT PANEL vehicle is experiencing a problem with the charging If the light remains lit with the engine running your system. Obtain SERVICE IMMEDIATELY. See an autho- vehicle, will usually be drivable, however, see an authorized dealer for service as soon as possible. If the light is rized dealer.
UNDERSTANDING YOUR INSTRUMENT PANEL shift the transmission into NEUTRAL and idle the vehicle. If the temperature reading does not return to normal, turn the engine off immediately and call for service. Refer to “If Your Engine Overheats” in “What To Do In Emergencies” for more information. • Transmission Temperature Warning Light This light indicates that there is excessive transmission fluid temperature that might occur with severe usage such as trailer towing.
268 UNDERSTANDING YOUR INSTRUMENT PANEL Engine Oil Change Indicator System Oil Change Due Your vehicle is equipped with an engine oil change indicator system. The “Oil Change Due” message will flash in the EVIC display for approximately 10 seconds after a single chime has sounded, to indicate the next scheduled oil change interval. The engine oil change indicator system is duty cycle based, which means the engine oil change interval may fluctuate, dependent upon your personal driving style. 2.
UNDERSTANDING YOUR INSTRUMENT PANEL 269 Press the UP/DOWN buttons to cycle through all the Trip Computer functions. The Trip Functions mode displays the following information: Average Fuel Economy / Fuel Saver Mode — If Equipped Shows the average fuel economy since the last reset. When the fuel economy is reset, the display will read “RESET” or show dashes for two seconds. Then, the history information will be erased, and the averaging will continue from the last fuel average reading before the reset.
270 UNDERSTANDING YOUR INSTRUMENT PANEL Distance To Empty (DTE) Shows the estimated distance that can be traveled with the fuel remaining in the tank. This estimated distance is determined by a weighted average of the instantaneous and average fuel economy, according to the current fuel tank level. DTE cannot be reset through the SELECT button. Vehicle Speed Press and release the UP or DOWN button until “Vehicle Speed” displays highlighted in the EVIC and press the SELECT button.
UNDERSTANDING YOUR INSTRUMENT PANEL 271 • Elapsed Time To Reset The Display Reset will only occur while a resettable function is being Press the UP/DOWN buttons to cycle through all the displayed. Press and release the SELECT button once to Trip Computer functions. clear the resettable function being displayed. To reset all The Trip Functions mode displays the following informa- resettable functions, press and hold the SELECT button for two seconds.
272 UNDERSTANDING YOUR INSTRUMENT PANEL Vehicle Info (Customer Information Features) Press and release the UP or DOWN button until “SYSTEM” displays in the EVIC and press the SELECT button. Press the UP and DOWN button to scroll through the available information displays, then press SELECT to display anyone of the following choices. • Coolant Temp Displays the actual coolant temperature. • Oil Temperature Displays the actual oil temperature. • Oil Pressure Displays the actual oil pressure.
UNDERSTANDING YOUR INSTRUMENT PANEL 273 • Your system can be set to display pressure units in PSI, kPa, or BAR. Keyless Enter-N-Go Display — If Equipped When the ENGINE START/STOP button is pressed to change ignition switch positions, the Keyless Enter-N-Go icon momentarily appears in the lower right corner of the EVIC display showing the new ignition switch position. Refer to “Keyless Enter-N-Go” in “Starting And Operating” for more information.
274 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: The system will display the last known outside temperature when starting the vehicle and may need to be driven several minutes before the updated temperature is displayed. Engine temperature can also affect the displayed temperature, therefore temperature readings are not updated when the vehicle is not moving.
UNDERSTANDING YOUR INSTRUMENT PANEL 275 5. Complete one or more 360–degree turns (in an area free from large metal or metallic objects) until the “CAL” indicator turns off. The compass will now function normally. Compass Variance Compass Variance is the difference between Magnetic North and Geographic North. To compensate for the differences the variance should be set for the zone where the vehicle is driven, per the zone map.
276 UNDERSTANDING YOUR INSTRUMENT PANEL 3. Press the DOWN button until the “Compass Variance” message is displayed in the EVIC, then press the SELECT button. The last variance zone number displays in the EVIC. Select Language When in this display you may select one of five languages for all display nomenclature, including the trip functions and the navigation system (if equipped). Press the UP or DOWN button while in this display and scroll 4.
UNDERSTANDING YOUR INSTRUMENT PANEL Auto Lock Doors When this feature is selected, all doors will lock automatically when the vehicle reaches a speed of 15 mph (24 km/h). To make your selection, press and release the SELECT button until a check-mark appears next to the feature showing the system has been activated, or the check-mark is removed showing the system has been deactivated.
278 UNDERSTANDING YOUR INSTRUMENT PANEL grasped. With Passive Entry, if Driver Door 1st Press is programmed touching the handle more than once will only result in the driver’s door opening. If driver door first is selected, once the driver door is opened, the interior door lock/unlock switch can be used to unlock all doors (or use RKE transmitter). RKE Linked To Memory When this feature is selected, you can use your RKE transmitter to recall one of two pre-programmed memory profiles.
UNDERSTANDING YOUR INSTRUMENT PANEL 279 Horn with Remote Lock When this feature is selected, a short horn sound will occur when the RKE transmitter LOCK button is pressed. This feature may be selected with or without the “Flash Lamps with Lock” feature. To make your selection, press and release the SELECT button until a check-mark appears next to the feature showing the system has been activated or the check-mark is removed, showing the system has been deactivated.
280 UNDERSTANDING YOUR INSTRUMENT PANEL Headlamps with Wipers (Available with Automatic Headlamps Only) When this feature is selected, and the headlight switch is in the AUTO position, the headlights will turn on approximately 10 seconds after the wipers are turned on. The headlights will also turn off when the wipers are turned off if they were turned on by this feature.
UNDERSTANDING YOUR INSTRUMENT PANEL REVERSE position. The mirrors will move back to their previous position when the transmission is shifted out of REVERSE. To make your selection, press and release the SELECT button until a check-mark appears next to the feature showing the system has been activated or the check-mark is removed, showing the system has been deactivated.
282 UNDERSTANDING YOUR INSTRUMENT PANEL next to the feature showing the system has been activated or the check-mark is removed, showing the system has been deactivated. Refer to “Keyless Enter-N-Go” in “Things To Know Before Starting Your Vehicle”. Wiper Mode — If Equipped When this feature is selected, the system will automatically activate the windshield wipers if it senses moisture on the windshield.
UNDERSTANDING YOUR INSTRUMENT PANEL Blind Spot Alert There are three selections when operating Blind Spot Alert. By pressing and releasing the SELECT button once, the Blind Spot Alert feature can be activated in “Blind Spot: Lights Only” mode. When this mode is selected the Blind Spot Monitor (BSM) system is activated and will only show a visual alert in the outside mirrors. By pressing and releasing the SELECT button a second time “Blind Spot: Lights/CHM” mode is activated.
284 UNDERSTANDING YOUR INSTRUMENT PANEL Display Units of Measure In: The EVIC, odometer, and Uconnect™ gps (if equipped) can be changed between English and Metric units of measure. To make your selection, press and release the SELECT button until “ENGLISH” or “METRIC” appears. Calibrate Compass Refer to “Compass Display” for more information. Compass Variance Refer to “Compass Display” for more information.
UNDERSTANDING YOUR INSTRUMENT PANEL 285 Power Switch/Volume Control (Rotary) Push the ON/VOLUME control knob to turn on the radio. Push the ON/VOLUME control knob a second time to turn off the radio. Electronic Volume Control The electronic volume control turns continuously (360 degrees) in either direction, without stopping. Turning the ON/VOLUME control knob to the right increases the volume, and to the left decreases it.
286 UNDERSTANDING YOUR INSTRUMENT PANEL TIME Button RW/FF Press the TIME button to alternate display of the time Pressing the RW (Rewind) or FF (Fast Forward) buttons and radio frequency. causes the tuner to search for the next frequency in the direction of the arrows. This feature operates in either Clock Setting Procedure AM or FM frequencies. 1. Press and hold the TIME button until the hours blink. TUNE Control 2.
UNDERSTANDING YOUR INSTRUMENT PANEL 287 Push the rotary TUNE/SCROLL control knob a third time and TREBLE will display. Turn the TUNE/SCROLL control knob to the right or left to increase or decrease the treble tones. SET/RND Button — To Set the Pushbutton Memory When you are receiving a station that you wish to commit to pushbutton memory, press the SET/RND button. The symbol SET 1 will now show in the display Push the rotary TUNE/SCROLL control knob a fourth window.
288 UNDERSTANDING YOUR INSTRUMENT PANEL Every time a preset button is used, a corresponding • This radio is capable of playing compact discs (CD), button number will display. recordable compact discs (CD-R), rewritable compact discs (CD-RW), compact discs with MP3 tracks and Buttons 1 - 6 multisession compact discs with CD and MP3 tracks.
UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! • This CD player will accept 4-3/4 in (12 cm) discs only. The use of other sized discs may damage the CD player mechanism. • Do not use adhesive labels. These labels can peel away and jam the player mechanism. • RES is a single CD player. Do not attempt to insert a second CD if one is already loaded. • Dual-media disc types (one side is a DVD, the other side is a CD) should not be used, and they can cause damage to the player.
290 UNDERSTANDING YOUR INSTRUMENT PANEL RW/FF Press and hold the FF (Fast Forward) button and the CD player will begin to fast forward until FF is released, or RW or another CD button is pressed. The RW (Reverse) button works in a similar manner. Notes on Playing MP3 Files The radio can play MP3 files; however, acceptable MP3 file recording media and formats are limited. When writing MP3 files, pay attention to the following restrictions. AM/FM Button Press the button to select either AM or FM mode.
UNDERSTANDING YOUR INSTRUMENT PANEL 291 Discs created with an option such as ⬙keep disc open after writing⬙ are most likely multisession discs. The use of • Maximum number of folders. (The radio display of file multisession for CD audio or MP3 playback may result in names and folder names is limited. For large numbers longer disc loading times. of files and/or folders, the radio may be unable to display the file name and folder name, and will assign Supported MP3 File Formats a number instead.
292 UNDERSTANDING YOUR INSTRUMENT PANEL MPEG Specification MPEG-1 Audio Layer 3 MPEG-2 Audio Layer 3 Sampling Frequency (kHz) 48, 44.1, 32 24, 22.05, 16 Bit Rate (kbps) 320, 256, 224, 192, 160, 128, 112, 96, 80, 64, 56, 48, 40, 32 160, 128, 144, 112, 96, 80, 64, 56, 48, 40, 32, 24, 16, 8 Playback of MP3 Files When a medium containing MP3 data is loaded, the radio checks all files on the medium.
UNDERSTANDING YOUR INSTRUMENT PANEL Operation Instructions - Auxiliary Mode The auxiliary (AUX) jack is an audio input jack, which allows the user to plug in a portable device, such as an MP3 player, or cassette player, and utilize the vehicle’s audio system to amplify the source and play through the vehicle speakers. MEDIA CENTER 130 WITH SATELLITE RADIO (SALES CODE RES+RSC) NOTE: The radio sales code is located on the lower right side of the radio faceplate.
294 UNDERSTANDING YOUR INSTRUMENT PANEL to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make NOTE: The ignition switch must be in the ON/RUN or another selection. Holding either button will bypass ACC position to operate the radio. stations without stopping until you release it.
UNDERSTANDING YOUR INSTRUMENT PANEL Phone Button Uconnect™ Phone — If Equipped Press this button to operate the Uconnect™ Phone feature (if equipped). Refer to “Uconnect™ Phone” in the Uconnect™ User Manual located on the DVD for further details. 295 3. After adjusting the hours, press the right side TUNE/ SCROLL control knob to set the minutes. The minutes will begin to blink. 4. Adjust the minutes using the right side TUNE/ SCROLL control knob.
296 UNDERSTANDING YOUR INSTRUMENT PANEL INFO Button Press the INFO button for an RDS station (one with call letters displayed). The radio will return a Radio Text message broadcast from an FM station (FM mode only). Push the rotary TUNE/SCROLL control knob a second time and MID will display. Turn the TUNE/SCROLL control knob to the right or left to increase or decrease the mid-range tones.
UNDERSTANDING YOUR INSTRUMENT PANEL MUSIC TYPE Button Pressing this button once will turn on the Music Type mode for five seconds. Pressing the MUSIC TYPE button or turning the TUNE/SCROLL control knob within five seconds will allow the program format type to be selected. Many radio stations do not currently broadcast Music Type information.
298 UNDERSTANDING YOUR INSTRUMENT PANEL Program Type Top 40 Weather 16-Digit Character Display Top 40 Weather hours, press the TUNE/SCROLL control knob to set the minutes. The minutes will begin to blink. Adjust the minutes using the right side TUNE/SCROLL control knob. Press the TUNE/SCROLL control knob to save time change. By pressing the SEEK button when the Music Type icon is displayed, the radio will be tuned to the next frequency AM/FM Button station with the same selected Music Type name.
UNDERSTANDING YOUR INSTRUMENT PANEL You may add a second station to each pushbutton by repeating the above procedure with this exception: Press the SET/RND button twice and SET 2 will show in the display window. Each button can be set for SET 1 and SET 2 in both AM and FM. This allows a total of 12 AM and 12 FM stations to be stored into pushbutton memory. The stations stored in SET 2 memory can be selected by pressing the pushbutton twice.
300 UNDERSTANDING YOUR INSTRUMENT PANEL If you insert a disc with the ignition ON/RUN and the EJECT Button - Ejecting a CD Press the EJECT button to eject the CD. radio ON, the unit will switch from radio to CD mode and begin to play when you insert the disc. The display will show the track number, and index time in minutes and seconds. Play will begin at the start of track 1. If you have ejected a disc and have not removed it within CAUTION! 10 seconds, it will be reloaded.
UNDERSTANDING YOUR INSTRUMENT PANEL SEEK Button Press the right SEEK button for the next selection on the CD. Press the left SEEK button to return to the beginning of the current selection, or return to the beginning of the previous selection if the CD is within the first second of the current selection. Pressing and holding the SEEK button will allow faster scrolling through the tracks in CD and MP3 modes.
302 UNDERSTANDING YOUR INSTRUMENT PANEL Supported Medium Formats (File Systems) • Maximum number of characters in file/folder names: The medium formats supported by the radio are ISO 9660 • Level 1: 12 (including a separator ⬙.⬙ and a threeLevel 1 and Level 2 and includes the Joliet extension. character extension) When reading discs recorded using formats other than • Level 2: 31 (including a separator ⬙.
UNDERSTANDING YOUR INSTRUMENT PANEL When using the MP3 encoder to compress audio data to an MP3 file, the bit rate and sampling frequencies in the following table are supported. In addition, variable bit rates (VBR) are also supported. The majority of MP3 files use a 44.1 kHz sampling rate and a 192, 160, 128, 96 or VBR bit rates. MPEG Specification Sampling Frequency (kHz) MPEG-1 Audio Layer 3 48, 44.1, 32 MPEG-2 Audio Layer 3 24, 22.
304 UNDERSTANDING YOUR INSTRUMENT PANEL To increase the speed of disc loading, it is recommended Press the INFO button once more to return to ⬙elapsed to use CD-R media and single-session discs. To create a time⬙ priority mode. single-session disc, enable the “Disc at Once” option Press and hold the INFO button for three seconds or before writing to the disc. more and the radio will display song titles for each file.
UNDERSTANDING YOUR INSTRUMENT PANEL 305 is not loud enough, turn the device’s volume up. If the System Activation AUX audio sounds distorted, turn the device’s volume Sirius Satellite Radio service is pre-activated, and you may begin listening immediately to the one year of audio down. service that is included with the factory-installed satellite TIME Button (Auxiliary Mode) radio system in your vehicle. Sirius will supply a welPress this button to change the display to time of day.
306 UNDERSTANDING YOUR INSTRUMENT PANEL To access the ESN/SID, refer to the following steps: ESN/SID Access With the ignition switch in the ON/RUN or ACC position and the radio on, press the SETUP button and scroll using the TUNE/SCROLL control knob until Sirius ID is selected. Press the TUNE/SCROLL control knob and the Sirius ID number will display. The Sirius ID number display will time out in two minutes. Press any button on the radio to exit this screen.
UNDERSTANDING YOUR INSTRUMENT PANEL 307 Operating Instructions - Uconnect™ Multimedia (Satellite) Mode INFO Button Pressing the INFO button will cycle the display information between Artist, Song Title, and Composer (if availNOTE: The ignition switch must be in the ON/RUN or able). Also, pressing and holding the INFO button for an ACC position to operate the radio.
308 UNDERSTANDING YOUR INSTRUMENT PANEL MUSIC TYPE Button Pressing this button once will turn on the Music Type mode for five seconds. Pressing the MUSIC TYPE button or turning the TUNE/SCROLL control knob within five seconds will allow the program format type to be selected. SETUP Button Pressing the SETUP button allows you to select the following items: • Display Sirius ID number — Press the AUDIO/ SELECT button to display the Sirius ID number.
UNDERSTANDING YOUR INSTRUMENT PANEL You may add a second channel to each pushbutton by repeating the above procedure with this exception: Press the SET button twice and SET 2 will show in the display window. Each button can be set for SET 1 and SET 2. This allows a total of 12 Satellite channels to be stored into pushbutton memory. The channels stored in SET 2 memory can be selected by pressing the pushbutton twice.
310 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: • If the radio has a USB port, refer to the appropriate Uconnect™ Multimedia radio User’s Manual for iPod威 or external USB device support capability. • Connecting an iPod威 or consumer electronic audio device to the AUX port located in the radio faceplate, plays media, but does not use the iPod威 /MP3 control feature to control the connected device.
UNDERSTANDING YOUR INSTRUMENT PANEL 311 Once the audio device is connected and synchronized to • The audio device can be controlled using the radio the vehicle’s iPod威 /MP3 control system (iPod威 or exterbuttons to Play, Browse, and List the iPod威 contents.
312 UNDERSTANDING YOUR INSTRUMENT PANEL Play Mode • Jump backward in the current track by pressing and When switched to iPod威 /MP3 control mode, the iPod威 holding the << RW button. Holding the << RW or external USB device automatically starts Play mode. In button long enough will jump to the beginning of Play mode, the following buttons on the radio faceplate the current track.
UNDERSTANDING YOUR INSTRUMENT PANEL 313 to the next screen of data for that track. Once all screens have been viewed, the last INFO button press will go back to the play mode screen on the radio. device, or press VR button and say ⬙Shuffle ON⬙ or ⬙Shuffle Off⬙. If the RND icon is showing on the radio display, then the shuffle mode is ON. • Pressing the REPEAT button will change the audio device mode to repeat the current playing track or press the VR button and say ⬙Repeat ON⬙ or ⬙Repeat Off⬙.
314 UNDERSTANDING YOUR INSTRUMENT PANEL fast will scroll through the list faster. During fast scroll, a slight delay in updating the information on the radio display may be noticeable. • Pressing a PRESET button will display the current list on the top line and the first item in that list on the second line. • During all List modes, the iPod威 displays all lists in “wrap-around” mode.
UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! • Leaving the iPod威 or external USB device (or any supported device) anywhere in the vehicle in extreme heat or cold can alter the operation or damage the device. Follow the device manufacturer’s guidelines. • Placing items on the iPod威 or external USB device, or connections to the iPod威 or external USB device in the vehicle, can cause damage to the device and/or to the connectors.
316 UNDERSTANDING YOUR INSTRUMENT PANEL 2. After the ⬙Ready⬙ prompt and the following beep, say Uconnect™ Multimedia ⬙Setup⬙, then ⬙Select Audio Devices⬙. (SIRIUS BACKSEAT TV™) — IF EQUIPPED Satellite video uses direct satellite receiver broadcasting 3. Say name of the audio device or ask Uconnect™ technology to provide streaming video. The subscription phone system to list audio devices. service provider is SIRIUS Satellite Radio.
UNDERSTANDING YOUR INSTRUMENT PANEL 317 screen, a battery-powered remote control, and two headsets. Refer to the “Uconnect™ Multimedia” section of Uconnect™ User Manual located on the DVD for further details. The LCD screen is located on the headliner behind the front seats.
318 UNDERSTANDING YOUR INSTRUMENT PANEL STEERING WHEEL AUDIO CONTROLS The remote sound system controls are located on the rear surface of the steering wheel. Reach behind the wheel to access the switches. The right-hand control is a rocker-type switch with a pushbutton in the center and controls the volume and mode of the sound system. Pressing the top of the rocker switch will increase the volume, and pressing the bottom of the rocker switch will decrease the volume.
UNDERSTANDING YOUR INSTRUMENT PANEL 319 The button located in the center of the left-hand control CD/DVD DISC MAINTENANCE will tune to the next preset station that you have pro- To keep a CD/DVD in good condition, take the following precautions: grammed in the radio preset pushbutton. CD Player Pressing the top of the switch once will go to the next track on the CD.
320 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: If you experience difficulty in playing a particu- Dual-Zone Manual Heating and Air Conditioning lar disc, it may be damaged (i.e., scratched, reflective coating removed, a hair, moisture or dew on the disc) oversized, or have protection encoding. Try a known good disc before considering disc player service.
UNDERSTANDING YOUR INSTRUMENT PANEL Blower Control Rotate this control to regulate the amount of air forced through the ventilation system in any mode. The blower speed increases as you move the control to the right from the “O” (OFF) position. There are seven blower speeds. Temperature Controls • Driver Temperature Control Rotate this control to regulate the temperature of the air inside the passenger compartment for the left front seat occupant.
322 UNDERSTANDING YOUR INSTRUMENT PANEL Floor Mode Control (Air Direction) Push the mode control buttons to choose from several Air is directed through the floor outlets with a patterns of air distribution. small amount flowing through the defrost and side window demist outlets. Panel Air is directed through the outlets in the instrument Mix panel. These outlets can be adjusted to direct airflow. Air is directed through the floor, defrost, and side window demist outlets.
UNDERSTANDING YOUR INSTRUMENT PANEL 323 NOTE: NOTE: • In Floor, Mix and Defrost modes a small amount of air • Continuous use of the recirculation mode may make will flow through the outboard panel outlets for the inside air stuffy and window fogging may occur. occupant comfort. Extended use of this mode is not recommended.
324 UNDERSTANDING YOUR INSTRUMENT PANEL Air Conditioning Control Press this button to engage the Air Conditioning. A light will illuminate when the Air Conditioning System is engaged. Rotating the dial left into the blue area of the scale indicates cooler temperatures while rotating right into the red area indicates warmer temperatures.
UNDERSTANDING YOUR INSTRUMENT PANEL 325 2. Recirculation Control Button Press and release to change the current setting, the indicator illuminates when ON. 3. Left Front Seat Occupant Temperature Display This display shows the temperature setting for the left front seat occupant. 4. Mode Display This display shows the current Mode selection (Panel, Bi-Level, Floor, Mix). Automatic Temperature Control (ATC) Panel 1.
326 UNDERSTANDING YOUR INSTRUMENT PANEL will cause the ATC to switch into manual mode. The 11. Blower Control blower will engage immediately if the Defrost mode is There are seven blower speeds, the blower speed increases as you move the control to the right from the selected. lowest blower setting. Performing this function will 8. Passenger Temperature Control Up Button cause the ATC to switch into manual mode. Provides the passenger with independent temperature control.
UNDERSTANDING YOUR INSTRUMENT PANEL 327 3. When the system is set up for your comfort level, it is 15. Driver Temperature Control Down Button Provides the driver with independent temperature con- not necessary to change the settings. You will experience the greatest efficiency by simply allowing the system to trol. Push the button for cooler temperature settings. function automatically. 16.
328 UNDERSTANDING YOUR INSTRUMENT PANEL selected. This allows the front occupants to control the Manual Operation This system offers a full complement of manual override volume of air circulated in the vehicle and cancel the features. Auto mode. NOTE: Each of these features operate independently The operator can also select the direction of the airflow from each other. If any one feature is controlled manually, by selecting one of the following positions.
UNDERSTANDING YOUR INSTRUMENT PANEL 329 NOTE: In many temperature positions, the BI-LEVEL temperature settings for best windshield and side winmode is designed to provide cooler air out of the panel dow defrosting. When the defrost mode is selected, the blower will automatically default to medium-high unless outlets and warmer air from the floor outlets. the blower is controlled manually. Floor Mode Air comes from the floor outlets.
330 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: • If the system is in Mix, Floor or Defrost Mode, the A/C can be turned off, but the A/C system shall remain active to prevent fogging of the windows. mode is not allowed in the Floor/Defrost Mix and Defrost modes to improve window clearing operation. Recirculation will be disabled automatically if these modes are selected. • If fog or mist appears on the windshield or side glass, Operating Tips select Defrost mode and increase blower speed.
UNDERSTANDING YOUR INSTRUMENT PANEL 331 Regular cleaning of the inside of the windows with a non-filming cleaning solution (vinegar and water works very well) will help prevent contaminates (cigarette smoke, perfumes, etc.) from sticking to the windows. Contaminates increase the rate of window fogging. Winter Operation When operating the system during the winter months, make sure the air intake, located directly in front of the windshield, is free of ice, slush, snow, or other obstructions.
332 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Tips Chart
STARTING AND OPERATING CONTENTS 䡵 Starting Procedures . . . . . . . . . . . . . . . . . . . . 339 䡵 Automatic Transmission . . . . . . . . . . . . . . . . . 345 ▫ Automatic Transmission . . . . . . . . . . . . . . . 339 ▫ Key Ignition Park Interlock . . . . . . . . . . . . . 345 ▫ Keyless Enter-N-Go . . . . . . . . . . . . . . . . . . . 340 ▫ Brake/Transmission Shift Interlock System . . 346 ▫ Normal Starting . . . . . . . . . . . . . . . . . . . . . 341 ▫ Five-Speed Automatic Transmission . . . . .
334 STARTING AND OPERATING ▫ Quadra-Trac II威 Operating Instructions/ 䡵 On-Road Driving Tips . . . . . . . . . Precautions – If Equipped . . . . . . . . . . . . . . 355 䡵 Off-Road Driving Tips . . . . . . . . . ▫ Shift Positions . . . . . . . . . . . . . . . . . . . . . . 356 ▫ Quadra-Lift™ – If Equipped . . . ▫ Shifting Procedures . . . . . . . . . . . . . . . . . . . 357 ▫ When To Use 4WD Low Range – ▫ Quadra-Drive威 II System – If Equipped . . . . 359 If Equipped . . . . . . . . . . . . . . . . . . . .
STARTING AND OPERATING 335 ▫ Power Steering Fluid Check . . . . . . . . . . . . . 375 ▫ Rain Brake Support – If Equipped . . . . . . . . 387 䡵 Multi-Displacement System (MDS) (If Equipped) — 5.7L Engine Only . . . . . . . . . . 376 ▫ Hill Descent Control (HDC) — Four-Wheel Drive Models With MP3023 Two-Speed Transfer Case Only . . . . . . . . . . . . . . . . . . . 387 䡵 Parking Brake . . . . . . . . . . . . . . . . . . . . . . . . 376 䡵 Electronic Brake Control System . . . . . . . . . . .
336 STARTING AND OPERATING ▫ Tire Pressures For High Speed Operation . . . 403 䡵 Tire Rotation Recommendations . . . . . . . . . . . 411 ▫ Radial-Ply Tires . . . . . . . . . . . . . . . . . . . . . 403 䡵 Tire Pressure Monitor System (TPMS) . . . . . . . 412 ▫ Spare Tire Matching Original Equipped Tire And Wheel – If Equipped . . . . . . . . . . . . . . 404 ▫ Base System . . . . . . . . . . . . . . . . . . . . . . . . 415 ▫ Compact Spare Tire – If Equipped . . . . . . . .
STARTING AND OPERATING 337 ▫ Fuel System Cautions . . . . . . . . . . . . . . . . . 425 䡵 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . 430 ▫ Carbon Monoxide Warnings . . . . . . . . . . . . 426 ▫ Fuel Filler Cap (Gas Cap) . . . . . . . . . . . . . . 430 䡵 Flexible Fuel (3.6L Engine Only) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 426 ▫ Loose Fuel Filler Cap Message . . . . . . . . . . . 433 ▫ E85 General Information . . . . . . . . . . . . . . .
338 STARTING AND OPERATING 䡵 Snow Plow . . . . . . . . . . . . . . . . . . . . . . . . . . 450 䡵 Recreational Towing (Behind Motorhome, Etc.) . . . . . . . . . . . . . . . . 451 ▫ Towing This Vehicle Behind Another Vehicle . . . . . . . . . . . . . . . . 451 ▫ Recreational Towing — Two-Wheel Drive Models . . . . . . . . . . . . . . . . . . . . . . . . . . . 452 ▫ Recreational Towing — Quadra-Trac I威 (Single-Speed Transfer Case) Four-Wheel Drive Models . . . . . . . . . . . . . . . . . . . . . . .
STARTING AND OPERATING STARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust the inside and outside mirrors, fasten your seat belt, and if present, instruct all other occupants to buckle their seat belts. WARNING! Never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Do not leave the key fob in the ignition switch.
340 STARTING AND OPERATING Do not press the accelerator. Use the Fob with Integrated Key to briefly turn the ignition switch to the START position and release it as soon as the starter engages. The starter motor will continue to run, and it will disengage automatically when the engine is running. If the engine fails to start, the starter will disengage automatically in 10 seconds.
STARTING AND OPERATING 341 NOTE: The ENGINE START/STOP button should only To Turn Off the Engine Using ENGINE be removed or inserted with the ignition in the LOCK START/STOP Button position (OFF position for Keyless Enter-N-Go). 1. Place the shift lever in PARK, then press and release the ENGINE START/STOP button. Normal Starting Using the ENGINE START/STOP Button 2. The ignition switch will return to the OFF position. NOTE: Normal starting of either a cold or a warm 3.
342 STARTING AND OPERATING NOTE: If the ignition switch is left in the ACC or RUN • Press the ENGINE START/STOP button once to (engine not running) position and the transmission is in change the ignition switch to the ACC position (EVIC PARK, the system will automatically time out after displays “IGNITION MODE ACCESSORY”), 30 minutes of inactivity and the ignition will switch to the • Press the ENGINE START/STOP button a second time OFF position.
STARTING AND OPERATING If Engine Fails To Start WARNING! • Never pour fuel or other flammable liquids into the throttle body air inlet opening in an attempt to start the vehicle. This could result in a flash fire causing serious personal injury. • Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transmission cannot be started this way.
344 STARTING AND OPERATING release it as soon as the starter engages. The starter motor The engine block heater cord is located: will disengage automatically in 10 seconds. Once this • 3.6L Engine – coiled and strapped to the engine oil occurs, release the accelerator pedal, turn the ignition dipstick tube. switch to the LOCK position, wait 10 to 15 seconds, then • 5.7L Engine – bundled and fastened to the injector repeat the “Normal Starting” procedure. harness.
STARTING AND OPERATING AUTOMATIC TRANSMISSION CAUTION! Damage to the transmission may occur if the following precautions are not observed: • Shift into PARK only after the vehicle has come to a complete stop. • Shift into or out of REVERSE only after the vehicle has come to a complete stop and the engine is at idle speed. • Do not shift from REVERSE, PARK, or NEUTRAL into any forward gear when the engine is above idle speed.
346 STARTING AND OPERATING Brake/Transmission Shift Interlock System This vehicle is equipped with a Brake Transmission Shift Interlock System (BTSI) that holds the shift lever in the PARK position when the ignition switch is in the LOCK position. To move the shift lever out of the PARK position, the ignition switch must be turned to the ON or START position (engine running or not) and the brake pedal must be pressed.
STARTING AND OPERATING WARNING! • Never use the PARK position as a substitute for the parking brake. Always apply the parking brake fully when parked to guard against vehicle movement and possible injury or damage. • It is dangerous to move the shift lever out of PARK or NEUTRAL if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in reverse. You could lose control of the vehicle and hit someone or something.
348 STARTING AND OPERATING Electronic Range Select (ERS) Operation The Electronic Range Select (ERS) shift control allows you to move the shift lever left (-) or right (+) when the shift lever is in the DRIVE position, allowing you to limit the highest available gear. For example, if the driver shifts the transmission into ERS 3 (third gear), the transmission will never shift above third gear, but can shift down to 2 (second) or 1 (first), when needed. 3.
STARTING AND OPERATING the ERS designation for the current gear (the transmission will not downshift). For example, if you are in DRIVE and are in third (direct) gear, when you tap the shift lever one time to the left (-), the display will show 4 (ERS 4 is direct gear). Another tap to the left (-) will shift the transmission down to ERS 3 (the added underdrive gear).
350 STARTING AND OPERATING • vehicle speed is above approximately 30 mph If the transmission temperature gets extremely hot, the transmission will automatically select the most desirable (48 km/h); gear for operation at this temperature. If the transmission • the TOW/HAUL switch has not been activated; temperature becomes hot enough, the “TRANSMISSION • transmission has reached normal operating OVER TEMP” message may display, and the transmistemperature.
STARTING AND OPERATING 351 operating in TOW/HAUL mode, the transmission will normal operation. If the TOW/HAUL mode is desired, shift into direct gear and Overdrive will be enabled the switch must be pressed each time the engine is started. under steady cruise conditions. In high ambient temperatures with sustained high engine speed and load, an upshift, followed shortly thereafter by a downshift, may occur. The “TOW/HAUL Indicator Light” will turn off.
352 STARTING AND OPERATING To reset the transmission, use the following procedure: Torque Converter Clutch A feature, designed to improve fuel economy, has been 1. Stop the vehicle. included in the automatic transmission on your vehicle. A clutch within the torque converter engages automati2. Move the shift lever into the PARK position. cally, at a calibrated speed, at light throttle. It engages at 3. Turn the engine off, and be sure to turn the ignition higher speeds under heavier acceleration.
STARTING AND OPERATING gear) positions will demonstrate that the transmission is able to shift into and out of Overdrive. For vehicles with 5.7L engines (which have two Overdrive gears), the transmission may not shift into the top Overdrive gear (normal fifth gear) until the transmission fluid and engine coolant are warm. • If the vehicle has not been driven in several days, the first few seconds of operation after shifting the transmission into gear may seem sluggish.
354 STARTING AND OPERATING The least amount of accelerator pedal pressure to maintain the rocking motion, without spinning the wheels or racing the engine, is most effective. Racing the engine or spinning the wheels may lead to transmission overheating and failure. Allow the engine to idle with the shift lever in NEUTRAL for at least one minute after every five rocking-motion cycles.
STARTING AND OPERATING 355 Quadra-Trac II姞 Operating Instructions/ • NEUTRAL Precautions – If Equipped • 4WD LOW The Quadra-Trac II威 transfer case is fully automatic in the normal driving 4WD AUTO mode. The Quadra-Trac II威 This transfer case is fully automatic in the 4WD HI mode. transfer case provides three mode positions: When additional traction is required, the 4WD LOW position can be used to lock the front and rear driveshafts together and force the front and rear wheels to rotate at the same speed.
356 STARTING AND OPERATING Proper operation of four-wheel drive vehicles depends Shift Positions on tires of equal size, type, and circumference on each For additional information on the appropriate use of each wheel. Any difference will adversely affect shifting and transfer case mode position, see the information below: cause damage to the transfer case.
STARTING AND OPERATING 357 and rear wheels to rotate at the same speed. It provides additional traction and maximum pulling power for loose, slippery road surfaces only. Do not exceed 25 mph (40 km/h). NOTE: Refer to “Selec-Terrain威 – If Equipped” for further information on the various positions and their intended usages.
358 STARTING AND OPERATING 4WD LOW to 4WD HI With the vehicle at speeds of 0 to 3 mph (0 to 5 km/h), the ignition switch in the ON position or the engine running, shift the transmission into NEUTRAL, and press the “4WD LOW” button once on the transfer case switch. The “4WD LOW” indicator light in the instrument cluster will flash and go out when the shift is complete.
STARTING AND OPERATING the Electronic Vehicle Information Center (EVIC). Refer to “Electronic Vehicle Information Center (EVIC)” in “Understanding Your Instrument Panel” for further information. Neutral Switch 5. Repeat Steps 1 to 4 to shift out of NEUTRAL. 359 NOTE: If shift conditions/interlocks are not met, a “To Tow Vehicle Safely, Read Neutral Shift Procedure in Owners Manual” message will flash from the Electronic Vehicle Information Center (EVIC).
360 STARTING AND OPERATING case and axle coupling differ in design, their operation is similar. Follow the Quadra-Trac II威 transfer case shifting information, preceding this section, for shifting this system. SELEC-TERRAIN™ — IF EQUIPPED Description Selec-Terrain™ combines the capabilities of the vehicle control systems, along with driver input, to provide the best performance for all terrains.
STARTING AND OPERATING to allow more driver control of vehicle while maintaining safe handling controls. The vehicle will lower (if equipped with Air Suspension) to Aero Mode in High Range. 4WD Low is not available in SPORT mode, if 4WD Low is selected the Selec-Terrain™ will auto• matically switch back to AUTO. 361 traction with seamless steering feel to provide improved handling and acceleration over two-wheel drive vehicles. If equipped with air suspension, the level will change to NRH.
362 STARTING AND OPERATING equipped with air suspension, the vehicle level will change to Off-Road 2. If the Selec-Terrain™ switch is in ROCK mode, and the transfer case is switched from 4WD Low to 4WD High, the Selec-Terrain™ system will return to AUTO. Electronic Vehicle Information Center (EVIC) Display Messages When the appropriate conditions exist, a message will appear in the EVIC display.
STARTING AND OPERATING 363 the vehicle height will be automatically lowered to • Off-Road 1 (OR1) (Raises the vehicle approximately OR1. Refer to “Off-Road Driving Tips” in “Starting 1.3 in (33 mm) – This position should be the default and Operating” for further information. position for all off-road driving until OR2 is needed. A smoother and more comfortable ride will result. Press • Aero Mode (Lowers the vehicle approximately 0.
364 STARTING AND OPERATING • Park Mode (Lowers the vehicle approximately 1.5 in (38 mm) – This position lowers the vehicle for easier passenger entry and exit as well as lowering the rear of the vehicle for easier loading and unloading of cargo. To enter Park Mode, press the “Down” button once while the vehicle speed is below 25 mph (40 km/h). Once the vehicle speed goes below 15 mph (24 km/h) the vehicle height will begin to lower.
STARTING AND OPERATING To assist with changing a spare tire, the Quadra-Lift™ air suspension system has a feature which allows the automatic leveling to be disabled. Press and hold both the “Up” and “Down” buttons simultaneously between 5 and 10 seconds, a message will appear in the EVIC stating leveling has been disabled immediately after both buttons have been released. Refer to “Electronic Vehicle Information Center (EVIC)” in “Understanding Your Instrument Panel” for further information.
366 STARTING AND OPERATING Pressing the “UP” button once will move the suspension one position higher from the current position, assuming all conditions are met (i.e. engine running, speed below threshold, etc). The “UP” button can be pressed multiple times, each press will raise the requested level by one position up to a maximum position of OR2 or the highest position allowed based on current conditions (i.e. vehicle speed, etc).
STARTING AND OPERATING • Park Mode – Indicator lamp 3 will be illuminated when the vehicle is in Park Mode. If Park Mode is requested while vehicle speed is between 15 mph (24 km/h) and 25 mph (40 km/h), indicator lamp 4 will remain on solid and indicator lamp 3 will flash as the system waits for the vehicle to reduce speed.
368 STARTING AND OPERATING OFF-ROAD DRIVING TIPS NOTE: Prior to off-road driving, remove the front air dam to prevent damage. The front air dam is attached to the lower front fascia with seven quarter turn fasteners and can be removed by hand. Quadra-Lift™ – If Equipped When off-roading, it is recommended that the lowest useable vehicle height that will clear the current obstacle or terrain be selected. The vehicle height should then be raised as required by the changes in terrain.
STARTING AND OPERATING 369 Driving through water more than a few inches/ Driving Through Water Although your vehicle is capable of driving through centimeters deep will require extra caution to ensure water, there are a number of precautions that must be safety and prevent damage to your vehicle. If you must drive through water, try to determine the depth and the considered before entering the water.
370 STARTING AND OPERATING Standing Water Avoid driving in standing water deeper than 20 inches (51 cm), and reduce speed appropriately to minimize wave effects. Maximum speed in 20 inches (51 cm) of water is less than 5 mph (8 km/h). Maintenance After driving through deep water, inspect your vehicle fluids and lubricants (engine oil, transmission oil, axle, transfer case) to assure the fluids have not been contaminated.
STARTING AND OPERATING 371 regulate your speed. If the brakes are required to control Traction Downhill vehicle speed, apply them lightly and avoid locking or Shift the transmission into a low gear, and the transfer case into 4WD LOW range. Let the vehicle go slowly skidding the tires. down the hill with all four wheels turning against engine WARNING! compression drag. This will permit you to control the If the engine stalls, you lose forward motion, or vehicle speed and direction.
372 STARTING AND OPERATING • Completely inspect the underbody of your vehicle. Check tires, body structure, steering, suspension, and exhaust system for damage. • Inspect the radiator for mud and debris and clean as required. WARNING! Abrasive material in any part of the brakes may cause excessive wear or unpredictable braking. You might not have full braking power when you need it to prevent a collision.
STARTING AND OPERATING and increased ease of maneuverability in tight spaces. The system will vary its assist to provide light efforts while parking and good feel while driving. If the electrohydraulic power steering system experiences a fault that prevents it from providing power steering assist, then the system will provide mechanical steering capability.
374 STARTING AND OPERATING • If the condition persists, see your authorized dealer for • Upon initial start-up in cold weather, the power steerservice. ing pump may make noise for a short amount of time. This is due to the cold, thick fluid in the steering 5.7L Engine system. This noise should be considered normal, and it The standard power steering system will give you good does not in any way damage the steering system. vehicle response and increased ease of maneuverability in tight spaces.
STARTING AND OPERATING Power Steering Fluid Check Checking the power steering fluid level at a defined service interval is not required. The fluid should only be checked if a leak is suspected, abnormal noises are apparent, and/or the system is not functioning as anticipated. Coordinate inspection efforts through an authorized dealer. CAUTION! Do not use chemical flushes in your power steering system as the chemicals can damage your power steering components.
376 STARTING AND OPERATING MULTI-DISPLACEMENT SYSTEM (MDS) (IF EQUIPPED) — 5.7L ENGINE ONLY This feature offers improved fuel economy by shutting off four of the engine’s eight cylinders during light load and cruise conditions. The system is automatic with no driver inputs or additional driving skills required. NOTE: The MDS system may take some time to return to full functionality after a battery disconnect.
STARTING AND OPERATING NOTE: • When the parking brake is applied and the transmission is placed in gear, the “Brake Warning Light” will flash. If vehicle speed is detected, a chime will sound to alert the driver. Fully release the parking brake before attempting to move the vehicle. • This light only shows that the parking brake is applied. It does not show the degree of brake application.
378 STARTING AND OPERATING WARNING! (Continued) • Always fully apply the parking brake when leaving your vehicle, or it may roll and cause damage or injury. Also be certain to leave the transmission in PARK. Failure to do so may allow the vehicle to roll and cause damage or injury. CAUTION! If the “Brake Warning Light” remains on with the parking brake released, a brake system malfunction is indicated. Have the brake system serviced by an authorized dealer immediately.
STARTING AND OPERATING WARNING! The ABS cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. The ABS cannot prevent collisions, including those resulting from excessive speed in turns, driving on very slippery surfaces, or hydroplaning. The capabilities of an ABS-equipped vehicle must never be exploited in a reckless or dangerous manner which could jeopardize the user’s safety or the safety of others.
380 STARTING AND OPERATING benefit of the system, you must apply continuous braking pressure during the stopping sequence (do not “pump” the brakes). Do not reduce brake pedal pressure unless braking is no longer desired. Once the brake pedal is released, the BAS is deactivated. WARNING! The BAS cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions.
STARTING AND OPERATING WARNING! Many factors, such as vehicle loading, road conditions and driving conditions, influence the chance that wheel lift or rollover may occur. ERM cannot prevent all wheel lift or rollovers, especially those that involve leaving the roadway or striking objects or other vehicles. The capabilities of an ERMequipped vehicle must never be exploited in a reckless or dangerous manner which could jeopardize the user’s safety or the safety of others.
382 STARTING AND OPERATING as little throttle as possible. Be sure to adapt your speed High Range (Four-Wheel Drive Models) or and driving to the prevailing road conditions. Two-Wheel Drive Models WARNING! The Electronic Stability Control (ESC) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions.
STARTING AND OPERATING to be used if the vehicle is in deep snow, sand, or gravel conditions and more wheel spin than ESC would normally allow is required to gain traction. To turn ESC on again, momentarily press the “ESC OFF” switch. This will restore the normal “ESC On” mode of operation. 383 NOTE: To improve the vehicle’s traction when driving with snow chains, or starting off in deep snow, sand, or gravel, it may be desirable to switch to the “Partial Off” mode by pressing the “ESC OFF” switch.
384 STARTING AND OPERATING Trailer Sway Control (TSC) TSC uses sensors in the vehicle to recognize an excessively swaying trailer and will take the appropriate actions to attempt to stop the sway. The system may reduce engine power and apply the brake of the appropriate wheel(s) to counteract the sway of the trailer. TSC will become active automatically once an excessively swaying trailer is recognized. No driver action is required. Note that TSC cannot stop all trailers from swaying.
STARTING AND OPERATING HSA Activation Criteria The following criteria must be met in order for HSA to activate: • Vehicle must be stopped. • Vehicle must be on a 6% (approximate) grade or greater hill. • Gear selection matches vehicle uphill direction (i.e., vehicle facing uphill is in forward gear; vehicle backing uphill is in REVERSE gear). HSA will work in REVERSE and all forward gears when the activation criteria have been met. The system will not activate if the vehicle is placed in NEUTRAL or PARK.
386 STARTING AND OPERATING Towing With HSA HSA will provide assistance when starting on a grade when pulling a trailer. WARNING! • If you use a trailer brake controller with your trailer, your trailer brakes may be activated and deactivated with the brake switch. If so, when the brake pedal is released, there may not be enough brake pressure to hold the vehicle and trailer on a hill and this could cause a collision with another vehicle or object behind you.
STARTING AND OPERATING Ready Alert Braking – If Equipped Ready Alert Braking may reduce the time required to reach full braking during emergency braking situations. It anticipates when an emergency braking situation may occur by monitoring how fast the throttle is released by the driver. When the throttle is released very quickly, Ready Alert Braking applies a small amount of brake pressure. This brake pressure will not be noticed by the driver.
388 STARTING AND OPERATING When HDC is enabled, the HDC icon will be illuminated in the instrument cluster. HDC will automatically apply the brakes to control downhill speed to the selected level when necessary on grades greater than approximately 8%. It will usually not activate on level ground. HDC Operation in 4WD Low Range To enable HDC, press the HDC switch or put the Selec-Terrain™ system in the “ROCK” mode. The HDC icon will be illuminated in the instrument cluster and HDC will function.
STARTING AND OPERATING • PARK = HDC will not function HDC is intended for low speed off-road driving only. At vehicle speeds above 20 mph (32 km/h), HDC will no longer function. When the vehicle speed drops below 20 mph (32 km/h), HDC function will automatically resume and the vehicle speed will return to the chosen set speed. WARNING! HDC is only intended to assist the driver in controlling vehicle speed when descending hills.
390 STARTING AND OPERATING Malfunction Indicator Light” begins to flash during ac- TIRE SAFETY INFORMATION celeration, ease up on the accelerator and apply as little Tire Markings throttle as possible. Be sure to adapt your speed and driving to the prevailing road conditions. NOTE: • The “ESC Activation/Malfunction Indicator Light” and the “ESC OFF Indicator Light” come on momentarily each time the ignition switch is turned ON.
STARTING AND OPERATING 391 NOTE: • LT (Light Truck) - Metric tire sizing is based on U.S. • P (Passenger) - Metric tire sizing is based on U.S. design standards. The size designation for LT-Metric design standards. P-Metric tires have the letter “P” tires is the same as for P-Metric tires except for the molded into the sidewall preceding the size designaletters “LT” that are molded into the sidewall precedtion. Example: P215/65R15 95H. ing the size designation. Example: LT235/85R16.
392 STARTING AND OPERATING Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ⴖ....blank....ⴖ = Passenger car tire based on European design standards LT = Light truck tire based on U.S. design standards T = Temporary spare tire 31 = Overall diameter in inches (in) 215 = Section width in millimeters (mm) 65 = Aspect ratio in percent (%) — Ratio of section height to section width of tire 10.
STARTING AND OPERATING 393 EXAMPLE: Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions — The maximum speed corresponding to the speed symbol should only be achieved under specified operating conditions (i.e.
394 STARTING AND OPERATING Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full TIN, including the date code, located on the white sidewall side of the tire. Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the outboard side, then you will find it on the inboard side of the tire.
STARTING AND OPERATING 395 Tire Terminology and Definitions Term B-Pillar Cold Tire Pressure Maximum Inflation Pressure Recommended Inflation Pressure Tire Placard Definition The vehicle B-Pillar is a structural member of the body located between the front and rear door (of a four-door vehicle) running from the sill to the roof. Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or driven less than 1 mile (1.
396 STARTING AND OPERATING Tire Loading And Tire Pressure Tire and Loading Information Placard Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar.
STARTING AND OPERATING This placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) total weight your vehicle can carry 3) tire size designed for your vehicle 4) cold tire inflation pressures for the front, rear, and spare tires. 397 axles must not be exceeded. For further information on GAWRs, vehicle loading, and trailer towing, refer to “Vehicle Loading” in this section.
398 STARTING AND OPERATING 3. Subtract the combined weight of the driver and pas- NOTE: • The following table shows examples on how to calcusengers from XXX lbs or XXX kg. late total load, cargo/luggage, and towing capacities 4. The resulting figure equals the available amount of of your vehicle with varying seating configurations cargo and luggage load capacity. For example, if “XXX” and number and size of occupants.
STARTING AND OPERATING 399
400 STARTING AND OPERATING WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.
STARTING AND OPERATING WARNING! (Continued) • Unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • Always drive with each tire inflated to the recommended cold tire inflation pressure. Economy Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement.
402 STARTING AND OPERATING CAUTION! After inspecting or adjusting the tire pressure, always reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage it. Tire pressures change by approximately 1 psi (7 kPa) per 12°F (7°C) of air temperature change. Keep this in mind when checking tire pressure inside a garage, especially in the winter.
STARTING AND OPERATING 403 Tire Pressures For High Speed Operation Radial-Ply Tires The manufacturer advocates driving at safe speeds WARNING! within posted speed limits. Where speed limits or conditions are such that the vehicle can be driven at high Combining radial ply tires with other types of tires speeds, maintaining correct tire inflation pressure is very on your vehicle will cause your vehicle to handle important. Increased tire pressure and reduced vehicle poorly.
404 STARTING AND OPERATING Spare Tire Matching Original Equipped Tire and CAUTION! Wheel – If Equipped The spare tire of your vehicle is equivalent in look and Because of the reduced ground clearance, do not take function as the original equipment tire and wheel found your vehicle through an automatic car wash with a on the front or rear axle of your vehicle. This spare tire compact, full size or limited-use temporary spare may be used in the tire rotation for your vehicle. If your installed.
STARTING AND OPERATING 405 Since this tire has limited tread life the original equip- Full Size Spare – If Equipped ment tire should be repaired (or replaced) and reinstalled The full size spare is for temporary emergency use only. This tire may look like the original equipped tire on the on your vehicle at the first opportunity. front or rear axle of your vehicle, but it is not. This spare Do not install a wheel cover or attempt to mount a tire may have limited tread life.
406 STARTING AND OPERATING your original equipment tire, replace (or repair) the Tire Spinning original equipment tire and reinstall on the vehicle at the When stuck in mud, sand, snow, or ice conditions, do not spin your vehicle’s wheels above 30 mph (48 km/h). first opportunity. WARNING! WARNING! Limited-use spares are for emergency use only. Installation of this limited-use spare tire affects vehicle handling. With this tire, do not drive more than the speed listed on the limit-use spare wheel.
STARTING AND OPERATING Tread Wear Indicators Tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced. 407 These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes 1/16 in (2 mm). When the tread is worn to the tread wear indicators, the tire should be replaced.
408 STARTING AND OPERATING Replacement Tires The tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for Tires and the spare tire should be replaced after six years, regardless of the remaining tread. Failure to wear and correct cold tire inflation pressure. The manufollow this warning can result in sudden tire failure.
STARTING AND OPERATING 409 WARNING! WARNING! (Continued) • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle. This can cause unpredictable handling and stress to steering and suspension components. You could lose control and have a collision resulting in serious injury or death.
410 STARTING AND OPERATING • Due to limited clearance, use SAE class “S” low profile cables or traction devices only. Security Chain Company (SCC) Super Z6 #SZ 441 cables or equivalent are recommended. WARNING! Using tires of different size and type (M+S, Snow) between front and rear axles can cause unpredictable handling. You could lose control and have a collision.
STARTING AND OPERATING CAUTION! (Continued) • Observe the traction device manufacturer’s instructions on the method of installation, operating speed, and conditions for use. Always use the suggested operating speed of the device manufacturer’s if it is less than 30 mph (48 km/h). • Do not use traction devices on a compact spare tire. 411 Snow tires generally have lower speed ratings than what was originally equipped with your vehicle and should not be operated at sustained speeds over 75 mph (120 km/h).
412 STARTING AND OPERATING These effects can be reduced by timely rotation of tires. The benefits of rotation are especially worthwhile with aggressive tread designs such as those on On/Off-Road type tires. Rotation will increase tread life, help to maintain mud, snow, and wet traction levels, and contribute to a smooth, quiet ride. Refer to the “Maintenance Schedule” for the proper maintenance intervals. More frequent rotation is permissible if desired.
STARTING AND OPERATING the outside temperature decreases, the tire pressure will decrease. Tire pressure should always be set based on cold inflation tire pressure. This is defined as the tire pressure after the vehicle has not been driven for at least three hours, or driven less than 1 mile (1.6 km) after a three-hour period. Refer to “Tires – General Information” in “Starting and Operating” for information on how to properly inflate the vehicle’s tires.
414 STARTING AND OPERATING be ON. In this situation, the Tire Pressure Monitoring Telltale Light will turn OFF only after the tires have been inflated to the vehicle’s recommended cold tire pressure value. CAUTION! • The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures have been established for the tire size equipped on your vehicle.
STARTING AND OPERATING • The TPMS is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure using an accurate tire gauge, even if under-inflation has not reached the level to trigger illumination of the Tire Pressure Monitoring Telltale Light.
416 STARTING AND OPERATING will automatically update and the Tire Pressure Monitoring Telltale Light will extinguish, once the updated tire pressures have been received. The vehicle may need to be driven for up to 20 minutes above 15 mph (24 km/h) to receive this information. The Tire Pressure Monitoring Telltale Light will flash on and off for 75 seconds, and remain on solid when a system fault is detected.
STARTING AND OPERATING on solid. In addition, a “SERVICE TPM SYSTEM” message will be displayed for 75 seconds. For each subsequent ignition switch cycle, a chime will sound, a “SERVICE TPM SYSTEM” message will be displayed for 75 seconds, and the Tire Pressure Monitoring Telltale Light will flash on and off for 75 seconds and then remain on solid.
418 STARTING AND OPERATING • Tire Pressure Monitoring Telltale Light Tire Pressure Monitoring Low Pressure Warnings The Tire Pressure Monitoring Telltale Light will illuminate in the instrument cluster, and an audible chime will be activated, when one or more of the four active road tire pressures are low.
STARTING AND OPERATING 419 Should a low tire condition occur on any of the four NOTE: Your system can be set to display pressure units active road tire(s), you should stop as soon as possible, in PSI, kPa, or BAR. and inflate the low tire(s) that is “flashing” on the graphic display to the vehicle’s recommended cold tire pressure.
420 STARTING AND OPERATING message will not be present, and a pressure value will be ⬙SERVICE TPM SYSTEM⬙ message is then followed by a displayed instead of dashes. A system fault can occur by graphic display, with pressure values still shown. This indicates the pressure values are still being received from any of the following: the TPM Sensors but they may not be located in the 1. Jamming due to electronic devices or driving next to correct vehicle position.
STARTING AND OPERATING the EVIC will display a “SERVICE TPM SYSTEM⬙ message for three seconds and then display dashes (- -) in place of the pressure value. For each subsequent ignition switch cycle, a chime will sound, the Tire Pressure Monitoring Telltale Light will flash on and off for 75 seconds and then remain on solid, and the EVIC will display a ⬙SERVICE TPM SYSTEM⬙ message for three seconds and then display dashes (- -) in place of the pressure value.
422 STARTING AND OPERATING FUEL REQUIREMENTS 3.6L Engine This engine is designed to meet all emissions regulations and provide excellent fuel economy and performance when using high-quality unleaded “regular” gasoline having an octane rating of 87. The use of premium gasoline is not recommended, as it will not provide any benefit over regular gasoline in these engines. 5.
STARTING AND OPERATING Reformulated Gasoline Many areas of the country require the use of cleaner burning gasoline referred to as “Reformulated Gasoline.” Reformulated gasoline contains oxygenates and are specifically blended to reduce vehicle emissions and improve air quality. The manufacturer supports the use of reformulated gasoline. Properly blended reformulated gasoline will provide excellent performance and durability of engine and fuel system components.
424 STARTING AND OPERATING If a Non-FFV vehicle is inadvertently fueled with E85 MMT In Gasoline fuel, the engine will have some or all of these symptoms: MMT is a manganese-containing metallic additive that is blended into some gasoline to increase octane. Gasoline • operate in a lean mode blended with MMT provides no performance advantage • OBD II “Malfunction Indicator Light” on beyond gasoline of the same octane number without MMT.
STARTING AND OPERATING Materials Added to Fuel All gasoline sold in the United States is required to contain effective detergent additives. Use of additional detergents or other additives is not needed under normal conditions and they would result in additional cost. Therefore, you should not have to add anything to the fuel. Fuel System Cautions CAUTION! Follow these guidelines to maintain your vehicle’s performance: • The use of leaded gas is prohibited by Federal law.
426 STARTING AND OPERATING Carbon Monoxide Warnings WARNING! (Continued) WARNING! Carbon monoxide (CO) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • Do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas, which can kill. Never run the engine in a closed area, such as a garage, and never sit in a parked vehicle with the engine running for an extended period.
STARTING AND OPERATING the other sections of this manual for information on features that are common between Flexible Fuel and gasoline-only powered vehicles. 427 CAUTION! Only vehicles with the E85 fuel filler door label can operate on E85.
428 STARTING AND OPERATING Ethanol Fuel (E85) When you do switch fuel types it is recommended that: E85 is a mixture of approximately 85% fuel ethanol and • you do not switch when the fuel gauge indicates less 15% unleaded gasoline. than 1/4 full WARNING! Ethanol vapors are extremely flammable and could cause serious personal injury. Never have any smoking materials lit in or near the vehicle when removing the fuel filler tube cap (gas cap) or filling the tank.
STARTING AND OPERATING • Some additives used in regular gasoline are not fully compatible with E85 and may form deposits in your engine. To eliminate driveability issues that may be caused by these deposits, a supplemental gasoline additive, such as MOPAR威 Injector Cleanup or Techron may be used. Selection Of Engine Oil For Flexible Fuel Vehicles (E85) and Gasoline Vehicles FFV vehicles operated on E85 require specially formulated engine oils.
430 STARTING AND OPERATING Replacement Parts Many components in your Flexible Fuel Vehicle (FFV) are designed to be compatible with ethanol. Always be sure that your vehicle is serviced with correct ethanol compatible parts. CAUTION! Replacing fuel system components with non-ethanol compatible components can damage your vehicle. Maintenance CAUTION! Do not use ethanol mixture greater than 85% in your vehicle. It will cause difficulty in cold starting and may affect driveability.
STARTING AND OPERATING 431 5 Fuel Filler Door Release Switch 2. Open the fuel filler door, and remove the fuel filler cap.
432 STARTING AND OPERATING CAUTION! WARNING! • Damage to the fuel system or emission control system could result from using an improper fuel cap (gas cap). A poorly fitting cap could let impurities into the fuel system. Also, a poorly fitting aftermarket cap can cause the “Malfunction Indicator Light (MIL)” to illuminate, due to fuel vapors escaping from the system. • A poorly fitting gas cap may cause the MIL to turn on.
STARTING AND OPERATING NOTE: • When the fuel nozzle “clicks” or shuts off, the fuel tank is full. • Tighten the gas cap about one-quarter turn until you hear one click. This is an indication that the cap is properly tightened. • If the gas cap is not tighten properly, the MIL will come on. Be sure the gas cap is tightened every time the vehicle is refueled.
434 STARTING AND OPERATING Rating (GAWR) front and rear, and Vehicle Identification Number (VIN). A Month-Day-Hour (MDH) number is included on this label and indicates the month, day, and hour of manufacture. The bar code that appears on the bottom of the label is your VIN. Gross Vehicle Weight Rating (GVWR) The GVWR is the total permissible weight of your vehicle including driver, passengers, vehicle, options, trailer tongue weight, and cargo.
STARTING AND OPERATING 435 The entire vehicle should first be weighed on a commerInflation Pressure This is the cold tire inflation pressure for your vehicle for cial scale to ensure that the GVWR has not been exceeded. The weight on the front and rear of the vehicle all loading conditions up to full GAWR. should then be determined separately to be sure that the Curb Weight load is properly distributed over front and rear axle.
436 STARTING AND OPERATING CAUTION! Do not load your vehicle any heavier than the GVWR or the maximum front and rear GAWR. If you do, parts on your vehicle can break, or it can change the way your vehicle handles. This could cause you to lose control. Also, overloading can shorten the life of your vehicle. TRAILER TOWING In this section you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle.
STARTING AND OPERATING WARNING! If the gross trailer weight is 3,500 lbs (1 587 kg) or more, it is mandatory to use a weight-distributing hitch to ensure stable handling of your vehicle. If you use a standard weight-carrying hitch, you could lose control of your vehicle and cause a collision. Gross Combination Weight Rating (GCWR) The GCWR is the total permissible weight of your vehicle and trailer when weighed in combination.
438 STARTING AND OPERATING Trailer Tongue Weight (TW) The TW is the downward force exerted on the hitch ball by the trailer. In most cases it should not be less than 10% or more than 15% of the trailer load. You must consider this as part of the load on your vehicle. Frontal Area The frontal area is the maximum height multiplied by the maximum width of the front of a trailer.
STARTING AND OPERATING 439 WARNING! • An improperly adjusted weight-distributing hitch system may reduce handling, stability, and braking performance, and could result in a collision. • Weight-distributing hitch systems may not be compatible with Surge Brake Couplers. Consult with your hitch and trailer manufacturer or a reputable Recreational Vehicle dealer for additional information.
440 STARTING AND OPERATING With Weight-Distributing Hitch (Correct) Improper Adjustment of Weight-Distributing Hitch (Incorrect)
STARTING AND OPERATING Trailer Hitch Classification Your vehicle may be factory equipped for safe towing of trailers weighing over 3,500 lbs (1 587 kg) with the optional Trailer Tow Prep Package. See your authorized dealer for package content. The following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition.
442 STARTING AND OPERATING Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/ Model GCWR (Gross ComFrontal Area Max. GTW Max. Trailer Tongue Model bined Wt. Rating) (Gross Trailer Wt.) Wt. (See Note) 3.6L 4x2 8,900 lbs (4 037 kg) 40 sq ft (3.72 sq m) 5,000 lbs (2 268 kg) 500 lbs (227 kg) 3.6L 4x4 8,900 lbs (4 037 kg) 40 sq ft (3.72 sq m) 5,000 lbs (2 268 kg) 500 lbs (227 kg) 5.
STARTING AND OPERATING 443 Trailer And Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% to 15% of the Gross Trailer Weight (GTW) on the tow hitch of your vehicle. Loads balanced over the wheels, or heavier in the rear, can cause the trailer to sway severely side-to-side which will cause loss of control of vehicle and trailer. Failure to load trailers heavier in front is the cause of many trailer collisions.
444 STARTING AND OPERATING NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options, or authorized dealer-installed options, must be considered as part of the total load on your vehicle. Refer to “Tire Safety Information/Tire and Loading Information Placard” in “Starting and Operating” for further information.
STARTING AND OPERATING 445 WARNING! (Continued) WARNING! (Continued) • Make certain that the load is secured in the trailer and will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control. You could lose control of your vehicle and have a collision. • When hauling cargo or towing a trailer, do not overload your vehicle or trailer.
446 STARTING AND OPERATING Towing Requirements – Tires − Do not attempt to tow a trailer while using a compact spare tire. replacement procedures. Replacing tires with a higher load carrying capacity will not increase the vehicle’s GVWR and GAWR limits. Towing Requirements – Trailer Brakes − Proper tire inflation pressures are essential to the safe and satisfactory operation of your vehicle.
STARTING AND OPERATING 447 CAUTION! WARNING! (Continued) If the trailer weighs more than 1,000 lbs (454 kg) loaded, it should have its own brakes and they should be of adequate capacity. Failure to do this could lead to accelerated brake lining wear, higher brake pedal effort, and longer stopping distances. • Towing any trailer will increase your stopping distance. When towing, you should allow for additional space between your vehicle and the vehicle in front of you.
448 STARTING AND OPERATING The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. Refer to the following illustrations.
STARTING AND OPERATING 449 Towing Tips Before setting out on a trip, practice turning, stopping and backing the trailer in an area away from heavy traffic. The transmission fluid and filter should be changed if you REGULARLY tow a trailer for more than 45 minutes of continuous operation. Refer to “Maintenance Schedule” for the proper maintenance intervals. Automatic Transmission The DRIVE range can be selected when towing.
450 STARTING AND OPERATING Cooling System SNOW PLOW To reduce potential for engine and transmission over- Snow plows, winches, and other aftermarket equipment heating, take the following actions: should not be added to the front end of your vehicle. The airbag crash sensors may be affected by the change in the − City Driving front end structure. The airbags could deploy unexpectWhen stopped for short periods of time, shift the transedly or could fail to deploy during a collision.
STARTING AND OPERATING 451 RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.
452 STARTING AND OPERATING 6. Install a suitable clamping device, designed for towRecreational Towing — Two-Wheel Drive Models DO NOT flat tow this vehicle. Damage to the drivetrain ing, to secure the front wheels in the straight position. will result. 7. Disconnect the negative battery cable and secure it Recreational towing (for two-wheel drive models) is away from the battery post. allowed ONLY if the rear wheels are OFF the ground.
STARTING AND OPERATING NOTE: This vehicle may be towed on a flatbed or vehicle trailer provided all four wheels are OFF the ground. CAUTION! Towing this vehicle in violation of the above requirements can cause severe transmission and/or transfer case damage. Damage from improper towing is not covered under the New Vehicle Limited Warranty.
454 STARTING AND OPERATING CAUTION! (Continued) • Do not use a bumper-mounted clamp-on tow bar on your vehicle. The bumper face bar will be damaged. Shifting Into NEUTRAL (N) WARNING! You or others could be injured if you leave the vehicle unattended with the transfer case in the NEUTRAL (N) position without first fully engaging the parking brake.
STARTING AND OPERATING 455 4. Turn the ignition switch to the ON/RUN position, but do not start the engine. 5. Press and hold the brake pedal. 6. Shift the transmission into NEUTRAL. 7. Using the point of a ballpoint pen or similar object, press and hold the recessed transfer case N (Neutral) button (located by the selector switch) for four seconds, until the light behind the N symbol starts to blink, indicating shift in progress.
456 STARTING AND OPERATING 12. Firmly apply the parking brake. 13. Shift the transmission into PARK. CAUTION! Damage to the transmission may occur if the transmission is shifted into PARK with the transfer case in NEUTRAL (N) and the engine running. With the transfer case in NEUTRAL (N) ensure that the engine is off prior to shifting the transmission into PARK. continue to be met until the four seconds elapse and the shift has been completed.
STARTING AND OPERATING 457 1. Bring the vehicle to a complete stop, leaving it con- DRIVE SYSTEM IN NEUTRAL” message will no longer nected to the tow vehicle. be displayed on the EVIC (Electronic Vehicle Information Center). Refer to “Electronic Vehicle Information Center 2. Firmly apply the parking brake. (EVIC)” in “Understanding Your Instrument Panel” for further information. 3. Reconnect the negative battery cable. 4.
458 STARTING AND OPERATING NOTE: When shifting out of transfer case NEUTRAL NOTE: (N), turning the engine OFF may be required to avoid • Steps 1 through 7 are requirements that must be met prior to pressing the NEUTRAL (N) button, and must gear clash. continue to be met until the shift has been completed. 9. Shift the transmission into PARK. If any of these requirements are not met prior to pressing the NEUTRAL (N) button or are no longer 10. Release the brake pedal.
WHAT TO DO IN EMERGENCIES CONTENTS 䡵 Hazard Warning Flashers . . . . . . . . . . . . . . . . 460 䡵 Jump-Starting . . . . . . . . . . . . . . . . . . . . . . . . 468 䡵 If Your Engine Overheats . . . . . . . . . . . . . . . . 460 ▫ Preparations For Jump-Start . . . . . . . . . . . . . 469 䡵 Jacking And Tire Changing . . . . . . . . . . . . . . . 461 ▫ Jump-Starting Procedure . . . . . . . . . . . . . . . 470 ▫ Jack Location . . . . . . . . . . . . . . . . . . . . . . .
460 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHERS IF YOUR ENGINE OVERHEATS The Hazard Warning flasher switch is located on the In any of the following situations, you can reduce the switch bank just above the climate controls. potential for overheating by taking the appropriate action. Press the switch to turn on the Hazard Warning flasher. When the switch is activated, all directional • On the highways — slow down.
WHAT TO DO IN EMERGENCIES • You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high. This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system. CAUTION! Driving with a hot cooling system could damage your vehicle. If the temperature gauge reads HOT (H), pull over and stop the vehicle.
462 WHAT TO DO IN EMERGENCIES WARNING! (Continued) • Being under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never put any part of your body under a vehicle that is on a jack. • Never start or run the engine while the vehicle is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift. • The jack is designed to be used as a tool for changing tires only.
WHAT TO DO IN EMERGENCIES Preparations for Jacking 1. Park the vehicle on a firm, level surface. Avoid ice or slippery surfaces. WARNING! Do not attempt to change a tire on the side of the vehicle closest to moving traffic, pull far enough off the road to avoid being hit when operating the jack or changing the wheel. 2. Turn on the Hazard Warning flasher. 3. Set the parking brake. 4. Place the shift lever into PARK. 5. Turn the ignition OFF. 463 6.
464 WHAT TO DO IN EMERGENCIES Jacking Instructions WARNING! (Continued) WARNING! Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: • Always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle. • Turn on the Hazard Warning flasher. • Block the wheel diagonally opposite the wheel to be raised. • Set the parking brake firmly and set an automatic transmission in PARK; a manual transmission in REVERSE.
WHAT TO DO IN EMERGENCIES 465 CAUTION! Do not attempt to raise the vehicle by jacking on locations other than those indicated in the Jacking Instructions for this vehicle. 1. Remove the spare tire, jack, and tools from storage. 2. Loosen (but do not remove) the wheel lug nuts by turning them to the left, one turn, while the wheel is still on the ground. 6 3. Assemble the jack and jacking tools.
466 WHAT TO DO IN EMERGENCIES 4. For the front axle, place the jack and protective cap on 5. For the rear axle, place the jack and protective cap in the body flange just behind the front tire Do not raise the the slot on the rear tie-down bracket, just forward of the vehicle until you are sure the jack is fully engaged. rear tire. Do not raise the vehicle until you are sure the jack is fully engaged.
WHAT TO DO IN EMERGENCIES 6. Raise the vehicle by turning the jack screw clockwise. Raise the vehicle only until the tire just clears the surface and enough clearance is obtained to install the spare tire. Minimum tire lift provides maximum stability. 467 WARNING! To avoid the risk of forcing the vehicle off the jack, do not fully tighten the wheel nuts until the vehicle has been lowered. WARNING! Raising the vehicle higher than necessary can make the vehicle less stable.
468 WHAT TO DO IN EMERGENCIES 12. Securely store the road wheel and jack in the cargo area. 13. Have the aluminum road wheel and tire repaired as soon as possible and properly secure the spare tire, jack and tool kit. WARNING! A loose tire or jack, thrown forward in a collision or hard stop could endanger the occupants of the vehicle. Always stow the jack parts and the spare tire in the places provided.
WHAT TO DO IN EMERGENCIES 469 NOTE: When using a portable battery booster pack Preparations For Jump-Start follow the manufacturer’s operating instructions and The battery in your vehicle is located under the passenger’s front seat. There are remote locations located under precautions. the hood to assist in jump-starting.
470 WHAT TO DO IN EMERGENCIES WARNING! • Take care to avoid the radiator cooling fan whenever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan blades. • Remove any metal jewelry such as watch bands or bracelets that might make an inadvertent electrical contact. You could be seriously injured. • Batteries contain sulfuric acid that can burn your skin or eyes and generate hydrogen gas which is flammable and explosive.
WHAT TO DO IN EMERGENCIES 471 CAUTION! WARNING! Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle. Do not connect the cable to the negative post (-) of the discharged battery. The resulting electrical spark could cause the battery to explode and could result in personal injury. 1. Connect the positive (+) end of the jumper cable to the 5.
472 WHAT TO DO IN EMERGENCIES 9. Disconnect the positive (+) end of the jumper cable EMERGENCY TOW HOOKS — IF EQUIPPED from the remote positive (+) post of the discharged If your vehicle is equipped with tow hooks, there will be one in the rear and two mounted on the front of the vehicle. vehicle. The rear hook will be located on the driver’s side 10. Reinstall the protective cover over the remote posiof the vehicle. tive (+) battery post of the discharged vehicle.
WHAT TO DO IN EMERGENCIES CAUTION! Tow hooks are for emergency use only, to rescue a vehicle stranded off road. Do not use tow hooks for tow truck hookup or highway towing. You could damage your vehicle. 473 4. Using a screwdriver or similar tool, carefully remove the shift lever override access cover, located on the bottom of the cupholder. 5. Press and maintain firm pressure on the brake pedal. 6. Using the screwdriver or similar tool, press and hold the shift lock lever down. SHIFT LEVER OVERRIDE 7.
474 WHAT TO DO IN EMERGENCIES NOTE: Vehicles equipped with Quadra-Lift™ must be lowered to the Park (lowest) level, and have automatic leveling disabled, before tying them down (from the body) on a trailer or flatbed truck. Refer to the section on Quadra-Lift™ for more information.
WHAT TO DO IN EMERGENCIES Proper towing or lifting equipment is required to prevent damage to your vehicle. Use only tow bars and other equipment designed for the purpose, following equipment manufacturer’s instructions. Use of safety chains is mandatory. Attach a tow bar or other towing device to main structural members of the vehicle, not to bumpers or associated brackets. State and local laws applying to vehicles under tow must be observed. If you must use the accessories (wipers, defrosters, etc.
476 WHAT TO DO IN EMERGENCIES Two-Wheel Drive Models If the transmission is not operable, or the vehicle must be The manufacturer recommends towing your vehicle with towed faster than 30 mph (48 km/h) or farther than all four wheels OFF the ground using a flatbed. 15 miles (24 km), tow with the rear wheels OFF the ground.
WHAT TO DO IN EMERGENCIES Four-Wheel Drive Vehicles The manufacturer recommends towing with all wheels OFF the ground. Acceptable methods are to tow the vehicle on a flatbed or with one end of vehicle raised and the opposite end on a towing dolly. If flatbed equipment is not available, and the transfer case is operable, the vehicle may be towed (in the forward direction, with ALL wheels on the ground), IF the transfer case is in NEUTRAL and the transmission is in PARK.
MAINTAINING YOUR VEHICLE CONTENTS 䡵 Engine Compartment – 3.6L . . . . . . . . . . . . . . 481 ▫ Engine Oil Filter . . . . . . . . . . . . . . . . . . . . . 490 䡵 Engine Compartment – 5.7L . . . . . . . . . . . . . . 482 ▫ Engine Air Cleaner Filter . . . . . . . . . . . . . . . 490 䡵 Onboard Diagnostic System – OBD II . . . . . . . 483 ▫ Maintenance-Free Battery . . . . . . . . . . . . . . 491 ▫ Loose Fuel Filler Cap Message . . . . . . . . . . . 483 ▫ Air Conditioner Maintenance . . . . . . . . . . .
480 MAINTAINING YOUR VEHICLE ▫ Brake System . . . . . . . . . . . . . . . . . . . . . . . 505 ▫ Halogen Headlamps – If Equipped . . . . . . . . 525 ▫ Front/Rear Axle Fluid . . . . . . . . . . . . . . . . . 507 ▫ Front Turn Signal . . . . . . . . . . . . . . . . . . . . 525 ▫ Transfer Case . . . . . . . . . . . . . . . . . . . . . . . 508 ▫ Front Fog Lamps . . . . . . . . . . . . . . . . . . . . 525 ▫ Automatic Transmission . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 481 ENGINE COMPARTMENT – 3.
482 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT – 5.
MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM – OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
484 MAINTAINING YOUR VEHICLE the SELECT button to turn off the message. If the Normally, the OBD II system will be ready. The OBD II problem continues, the message will appear the next time system may not be ready if your vehicle was recently serviced, recently had a dead battery or a battery replacethe vehicle is started. ment. If the OBD II system should be determined not A loose, improperly installed, or damaged fuel filler cap ready for the I/M test, your vehicle may fail the test.
MAINTAINING YOUR VEHICLE 485 4. Approximately 15 seconds later, one of two things will system to update. A recheck with the above test routine happen: may then indicate that the system is now ready. a. The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine. This means that your vehicle’s OBD II system is not ready and you should not proceed to the I/M station.
486 MAINTAINING YOUR VEHICLE DEALER SERVICE Your authorized dealer has the qualified service personnel, special tools, and equipment to perform all service operations in an expert manner. Service Manuals are available which include detailed service information for your vehicle. Refer to these Service Manuals before attempting any procedure yourself. NOTE: Intentional tampering with emissions control systems may void your warranty and could result in civil penalties being assessed against you.
MAINTAINING YOUR VEHICLE CAUTION! (Continued) • Your vehicle has been built with improved fluids that protect the performance and durability of your vehicle and also allow extended maintenance intervals. Do not use chemical flushes in these components as the chemicals can damage your engine, transmission, power steering or air conditioning. Such damage is not covered by the New Vehicle Limited Warranty.
488 MAINTAINING YOUR VEHICLE Change Engine Oil American Petroleum Institute (API) Engine Oil The oil change indicator system will remind you that it is Identification Symbol This symbol means that the oil has time to take your vehicle in for scheduled maintenance. been certified by the American Refer to “Maintenance Schedule” for further information. Petroleum Institute (API).
MAINTAINING YOUR VEHICLE Engine Oil Viscosity – 3.6L Engine SAE 5W-30 engine oil is recommended for all operating temperatures. This engine oil improves low temperature starting and vehicle fuel economy. The engine oil filler cap also shows the recommended engine oil viscosity for your vehicle. For information on engine oil filler cap location, refer to “Engine Compartment” in “Maintaining Your Vehicle” for further information.
490 MAINTAINING YOUR VEHICLE Materials Added to Engine Oils Do not add any supplemental materials, other than leak detection dyes, to your engine oil. Engine oil is an engineered product and its performance may be impaired by supplemental additives. Engine Oil Filter The engine oil filter should be replaced with a new filter at every oil change. Engine Oil Filter Selection The manufacturer’s engines have a full-flow type disposDisposing of Used Engine Oil and Oil Filters able oil filter.
MAINTAINING YOUR VEHICLE WARNING! The air induction system (air cleaner, hoses, etc) can provide a measure of protection in the case of engine backfire. Do not remove the air induction system (air cleaner, hoses, etc.) unless such removal is necessary for repair or maintenance. Make sure that no one is near the engine compartment before starting the vehicle with the air induction system (air cleaner, hoses, etc.) removed. Failure to do so can result in serious personal injury.
492 MAINTAINING YOUR VEHICLE WARNING! (Continued) CAUTION! • Battery gas is flammable and explosive. Keep flame or sparks away from the battery. Do not use a booster battery or any other booster source with an output greater than 12 Volts. Do not allow cable clamps to touch each other. • Battery posts, terminals, and related accessories contain lead and lead compounds. Wash hands after handling.
MAINTAINING YOUR VEHICLE Air Conditioner Maintenance For best possible performance, your air conditioner should be checked and serviced by an authorized dealer at the start of each warm season. This service should include cleaning of the condenser fins and a performance test. Drive belt condition should also be checked at this time. CAUTION! Do not use chemical flushes in your air conditioning system as the chemicals can damage your air conditioning components.
494 MAINTAINING YOUR VEHICLE Refrigerant Recovery and Recycling R-134a Air Conditioning Refrigerant is a hydrofluorocarbon (HFC) that is endorsed by the Environmental Protection Agency (EPA) and is an ozone-saving product. However, the manufacturer recommends that air conditioning service be performed by authorized dealers or other service facilities using recovery and recycling equipment.
MAINTAINING YOUR VEHICLE 495 Avoid using the wiper blades to wipe frost or ice from the windshield. Keep the blade rubber out of contact with petroleum products such as engine oil, gasoline, etc. NOTE: Life expectancy of wiper blades varies depending on geographical area and frequency of use. Poor performance of blades may be present with chattering, marks, water lines or wet spots. If any of these conditions are present, clean the wiper blades or replace as necessary.
496 MAINTAINING YOUR VEHICLE 3. Grab the bottom of the wiper blade and rotate it 4. Install the wiper blade pivot pin into the wiper blade forward to unsnap the blade pivot pin from the wiper holder at the end of the wiper arm, and firmly press the blade holder. wiper blade until it snaps into place. 5. Lower the wiper blade and snap the pivot cap into place. Adding Washer Fluid On vehicles equipped with a Electronic Vehicle Information Center (EVIC), the low washer fluid level will be indicated.
MAINTAINING YOUR VEHICLE clean the wiper blades, this will help blade performance. To prevent freeze-up of your windshield washer system in cold weather, select a solution or mixture that meets or exceeds the temperature range of your climate. This rating information can be found on most washer fluid containers. WARNING! Commercially available windshield washer solvents are flammable. They could ignite and burn you. Care must be exercised when filling or working around the washer solution.
498 MAINTAINING YOUR VEHICLE WARNING! CAUTION! • Exhaust gases can injure or kill. They contain carbon monoxide (CO), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing CO, refer to “Safety Tips/Exhaust Gas” in “Things To Know Before Starting Your Vehicle” for further information. • A hot exhaust system can start a fire if you park over materials that can burn.
MAINTAINING YOUR VEHICLE 499 Under normal operating conditions, the catalytic con- • Do not try to start the engine by pushing or towing the verter will not require maintenance. However, it is imporvehicle. tant to keep the engine properly tuned to assure proper • Do not idle the engine with any spark plug wires catalyst operation and prevent possible catalyst damage.
500 MAINTAINING YOUR VEHICLE Engine Coolant Checks Check the engine coolant (antifreeze) protection every 12 months (before the onset of freezing weather, where applicable). If the engine coolant (antifreeze) is dirty or rusty in appearance, the system should be drained, flushed and refilled with fresh engine coolant (antifreeze). Check the front of the A/C condenser for any accumulation of bugs, leaves, etc.
MAINTAINING YOUR VEHICLE CAUTION! • Mixing of engine coolant (antifreeze), other than the specified HOAT engine coolant (antifreeze), may result in engine damage and may decrease corrosion protection. If a non-HOAT engine coolant (antifreeze) is introduced into the cooling system in an emergency, it should be replaced with the specified engine coolant (antifreeze) as soon as possible. • Do not use water alone or alcohol based engine coolant (antifreeze) products.
502 MAINTAINING YOUR VEHICLE • Mix a minimum solution of 50% HOAT engine coolant (antifreeze) and distilled water. Use higher concentrations (not to exceed 70%) if temperatures below -34°F (-37°C) are anticipated. Cooling System Pressure Cap The cap must be fully tightened to prevent loss of engine coolant (antifreeze), and to ensure that engine coolant (antifreeze) will return to the radiator from the coolant recovery tank.
MAINTAINING YOUR VEHICLE WARNING! (Continued) • Do not use a pressure cap other than the one specified for your vehicle. Personal injury or engine damage may result. Disposal of Used Engine Coolant Used ethylene glycol-based engine coolant (antifreeze) is a regulated substance requiring proper disposal. Check with your local authorities to determine the disposal rules for your community.
504 MAINTAINING YOUR VEHICLE • If frequent engine coolant (antifreeze) additions are required, or if the level in the coolant recovery bottle NOTE: When the vehicle is stopped after a few miles does not drop when the engine cools, the cooling (kilometers) of operation, you may observe vapor coming system should be pressure tested for leaks. from the front of the engine compartment.
MAINTAINING YOUR VEHICLE Brake System In order to assure brake system performance, all brake system components should be periodically inspected. Refer to the “Maintenance Schedule” for the proper maintenance intervals. WARNING! Riding the brakes can lead to brake failure and possibly a collision. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage.
506 MAINTAINING YOUR VEHICLE WARNING! WARNING! (Continued) • Use only manufacturer’s recommended brake fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for further information. Using the wrong type of brake fluid can severely damage your brake system and/or impair its performance. The proper type of brake fluid for your vehicle is also labeled on the original factory installed hydraulic master cylinder reservoir.
MAINTAINING YOUR VEHICLE WARNING! (Continued) • Do not allow petroleum based fluid to contaminate the brake fluid. Brake seal components could be damaged, causing partial or complete brake failure. This could result in a collision. Front/Rear Axle Fluid For normal service, periodic fluid level checks are not required. When the vehicle is serviced for other reasons the exterior surfaces of the axle assembly should be inspected. If gear oil leakage is suspected inspect the fluid level.
508 MAINTAINING YOUR VEHICLE CAUTION! Do not over tighten the plugs as it could damage then and cause them to leak. Adding Fluid Add fluid at the filler hole, until it runs out of the hole, when the vehicle is in a level position. Drain First remove fill plug, then remove drain plug. RecomSelection of Lubricant mended tightening torque for drain and fill plugs is 15 to Use only the manufacturer’s recommended fluid. Refer 25 ft lbs (20 to 34 N·m).
MAINTAINING YOUR VEHICLE Automatic Transmission Selection of Lubricant It is important that the proper lubricant is used in the transmission to assure optimum transmission performance. Use only the manufacturer’s recommended transmission fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for further information. It is important that the transmission fluid be maintained at the prescribed level using the recommended fluid.
510 MAINTAINING YOUR VEHICLE CAUTION! CAUTION! Do not use chemical flushes in your transmission as the chemicals can damage your transmission components. Such damage is not covered by the New Vehicle Limited Warranty. • Using a transmission fluid other than the manufacturer’s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder.
MAINTAINING YOUR VEHICLE 511 6. Remove the dipstick again, and note the fluid level on both sides. The fluid level should be between the “HOT” (upper) reference holes on the dipstick at normal operating temperature. The fluid level is only valid if there is a solid coating of oil on both sides of the dipstick. If the fluid is low, add as required into the dipstick tube. Do To check the fluid level properly, the following procedure not overfill.
512 MAINTAINING YOUR VEHICLE CAUTION! Be aware that if the fluid temperature is below 50°F (10°C) it may not register on the dipstick. Do not add fluid until the temperature is elevated enough to produce an accurate reading. passable in snow and ice, and those that are sprayed on trees and road surfaces during other seasons, are highly corrosive to the metal in your vehicle.
MAINTAINING YOUR VEHICLE Washing • Wash your vehicle regularly. Always wash your vehicle in the shade using MOPAR威 Car Wash or a mild car wash soap, and rinse the panels completely with clear water. • If insects, tar, or other similar deposits have accumulated on your vehicle, use MOPAR威 Super Kleen Bug and Tar Remover or equivalent to remove. 513 CAUTION! • Do not use abrasive or strong cleaning materials such as steel wool or scouring powder, which will scratch metal and painted surfaces.
514 MAINTAINING YOUR VEHICLE • If you detect any stone chips or scratches in the paint, Wheel and Wheel Trim Care touch them up immediately. The cost of such repairs is All wheels and wheel trim, especially aluminum and chrome-plated wheels should be cleaned regularly with a considered the responsibility of the owner. mild soap and water to prevent corrosion.
MAINTAINING YOUR VEHICLE 515 • For tough stains, apply MOPAR威 Total Clean or a mild Leather Seat Care And Cleaning soap solution to a clean, damp cloth and remove the MOPAR威 Total Clean or equivalent is specifically recomstain. Use a fresh, damp towel to remove soap residue. mended for leather upholstery. • For grease stains, apply MOPAR威 Multi-Purpose Cleaner or equivalent to a clean, damp cloth and remove the stain. Use a fresh, damp towel to remove soap residue.
516 MAINTAINING YOUR VEHICLE WARNING! Do not use volatile solvents for cleaning purposes. Many are potentially flammable, and if used in closed areas, they may cause respiratory harm. Glass Surfaces All glass surfaces should be cleaned on a regular basis with MOPAR威 Glass Cleaner or any commercial household-type glass cleaner. Never use an abrasive type cleaner. Use caution when cleaning inside rear windows equipped with electric defrosters.
MAINTAINING YOUR VEHICLE 2. Dry with a soft cloth. Seat Belt Maintenance Do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage will also weaken the fabric. 517 component may be stamped on the inside cover, otherwise the cavity number of each fuse is stamped on the inside cover that corresponds to the following chart. If the belts need cleaning, use MOPAR威 Total Clean, a mild soap solution, or lukewarm water.
518 MAINTAINING YOUR VEHICLE Cavity J01 J02 J03 J04 J05 J06 J07 J08 Cartridge Fuse 40 Amp Green 30 Amp Pink 30 Amp Pink 25 Amp Natural 25 Amp Natural 40 Amp Green 30 Amp Pink 40 Amp Green Mini Fuse Description Cavity Air Suspension J09 Power Liftgate Module J10 Trailer Tow J11 Driver Door Node J12 Passenger Door Node J13 Antilock Brakes Pump/ Stability Control System Antilock Brakes Valve/ Stability Control System Power Seat J14 J15 J17 Cartridge Fuse 30 Amp Pink 30 Amp Pink 30 Amp Pink
MAINTAINING YOUR VEHICLE Cavity J18 J19 J20 J21 J22 M1 Cartridge Fuse 20 Amp Blue Mini Fuse Description Powertrain Control Module/Powertrain Control Module Transmission Range Radiator Fan Motor HI/ Radiator Fan Motor Low Front Wiper 60 Amp Yellow 30 Amp Pink 20 Amp Blue 25 Amp Natural 15 Amp Blue Cavity Mini Fuse Description M2 20 Amp Yellow M3 20 Amp Yellow 25 Amp Natural 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow Electronic Limit Slip Differential/Air Suspension Liftgate/Head
520 MAINTAINING YOUR VEHICLE Cavity M10 M11 M12 M13 M14 Cartridge Fuse Mini Fuse Description 15 Amp Blue 10 Amp Red Video/Universal Garage Door Opener Heating, Ventilation & Air Conditioning (Climate Control System) Radio/Amplifier 30 Amp Green 20 Amp Yellow 20 Amp Yellow Instrument Cluster Back Up Camera Cavity Mini Fuse Description M15 20 Amp Yellow M16 10 Amp Red 25 Amp Natural 15 Amp Blue 20 Amp Yellow Power Seat Module(s)/ Adaptive Cruise Control/Audio Telematics/Daytime Running Ligh
MAINTAINING YOUR VEHICLE Cavity M22 M23 M24 M25 M26 M27 M28 Cartridge Fuse Mini Fuse 10 Amp Red 10 Amp Red 25 Amp Natural 20 Amp Yellow 10 Amp Red 10 Amp Red 15 Amp Blue Description Horns (Low/High) – Right Horns (Low/High) – Left Rear Wiper Fuel Pump Motor Output/Diesel Lift Pump (Export Only) Driver Door Switch Bank Ignition Switch/Wireless Control Module/Keyless Entry Module Powertrain Controller/ Transmission Controller Cavity M29 M30 M31 M32 M33 M34 Cartridge Fuse Mini Fuse 10 Amp Red 15 Am
522 MAINTAINING YOUR VEHICLE Cavity M35 M36 M37 M38 Cartridge Fuse Mini Fuse 15 Amp Blue 20 Amp Yellow 10 Amp Red 25 Amp Natural Description Left Rear Parklamps Power Outlet Antilock Brakes/ Stability Control System Module All Door Lock &Unlock CAUTION! • When installing the totally integrated power module cover, it is important to ensure the cover is properly positioned and fully latched.
MAINTAINING YOUR VEHICLE 523 VEHICLE STORAGE REPLACEMENT BULBS If you are leaving your vehicle dormant for more than 21 days you may want to take steps to protect your Interior Lights Bulb Type battery. You may: Glove Box Lamp . . . . . . . . . . . . . . . . . . . . . . . . . 194 • Remove fuse #27 in the Totally Integrated Power Grab Handle Lamp . . . . . . . . . . . . . . . . L002825W5W Overhead Console Reading Lamps . . . . . . . . . VT4976 Module (TIPM) labeled Ignition-Off Draw (IOD#1).
524 MAINTAINING YOUR VEHICLE Exterior Lights Bulb Type Aux Aperature Backup Lamps . . . . . . . . 7440 (W21W) Auxiliary Liftgate Tail Lamps . . . . . . . . . . . . . . W3W Front Park/Turn Lamp . . . . . . . . . . . . . . . . . . . . T20 Front Fog Lamps . . . . . . . . . . . . . . . . . . . . . PSX24W Front Side Marker . . . . . . . . . . . . . . . . . . . . . . W5W Headlamps (Low Beam) – High Intensity Discharge (HID) . . . . . . . . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 525 NOTE: On vehicles equipped with High Intensity Discharge (HID) headlamps, when the headlamps are turned on, there is a blue hue to the lamps. This diminishes and becomes more white after approximately 10 seconds, as the system charges. Front Turn Signal Halogen Headlamps – If Equipped 3. Disconnect the electrical connector and replace the bulb. 1. Open the hood. 2. Turn the low or high beam bulb one–quarter turn counterclockwise to remove from housing. 3.
526 MAINTAINING YOUR VEHICLE 2. Firmly grasp the bulb by the two latches and squeeze 4. Align the index tabs of the front fog lamp bulb with them together to unlock the bulb from the back of the the slots in the collar of the bulb opening on the back of front fog lamp housing. the front fog lamp housing. 3. Pull the bulb straight out from the keyed opening in 5. Insert the bulb into the housing until the index tabs are the housing. engaged in the slots of the collar.
MAINTAINING YOUR VEHICLE Rear Tail, Stop, Turn Signal, And Backup Lamps 1. Raise the liftgate. 2. Remove the two push-pins from the tail lamp housing. 527 3. Grasp the tail lamp and pull firmly rearward to disengage the lamp from the aperture panel. 4. Twist socket counter clockwise and remove from lamp. 5. Pull the bulb to remove it from the socket. 6. Replace the bulb, reinstall the socket, and reattach the lamp assembly.
528 MAINTAINING YOUR VEHICLE Rear Liftgate Mounted Tail Lamp 1. Raise the liftgate. 2. Use a fiber stick or flat blade screw driver to pry the lower trim from the liftgate. 3. Once lower trim is loose, close the liftgate. 4. Open the flipper glass. 5. Pull up glass seal at bottom of window opening. 6. Remove small trim panel around liftgate glass striker. 7. Close flipper glass and raise the liftgate. 8. Continue removing the trim. 9. Disconnect the two trim panel lights. Rear Liftgate Tail Lamps 10.
MAINTAINING YOUR VEHICLE 529 Center High-Mounted Stop Lamp (CHMSL) Rear License Lamp The center high-mounted stop lamp is an LED assembly. 1. Use a screw driver to gently pry against the side of the See your authorized dealer for replacement. snap tab to remove the license lamp lens. 2. Pull bulb from socket. 3. Replace bulb. 4. Reinstall lens.
530 MAINTAINING YOUR VEHICLE FLUID CAPACITIES Fuel (Approximate) 3.6L and 5.7L Engines Engine Oil with Filter 3.6L Engine (SAE 5W-30, API Certified) 5.7L Engine (SAE 5W-20, API Certified) Cooling System * 3.6L Engine (MOPAR威 Engine Coolant/Antifreeze 5-Year/100,000 Mile Formula or equivalent) 5.7 Liter Engine (MOPAR威 Engine Coolant/Antifreeze 5-Year/100,000 Mile Formula or equivalent) – Without Trailer Tow Package 5.
MAINTAINING YOUR VEHICLE 531 FLUIDS, LUBRICANTS, AND GENUINE PARTS Engine Component Engine Coolant Engine Oil – 3.6L Engine Engine Oil – 5.7L Engine Engine Oil Filter Spark Plugs – 3.6L Engine Spark Plugs – 5.7L Engine Fuel Selection – 3.6L Engine Fuel Selection – 5.7L Engine Fluid, Lubricant, or Genuine Part MOPAR威 Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) or equivalent.
532 MAINTAINING YOUR VEHICLE Chassis Component Automatic Transmission Fluid, Lubricant, or Genuine Part MOPAR威 ATF+4威 Automatic Transmission Fluid or equivalent licensed ATF+4威 product. Transfer Case – 3.6L Engine Shell Automatic Transmission Fluid 3353 or equivalent. Transfer Case – 5.7L Engine MOPAR威 ATF+4威 Automatic Transmission Fluid or equivalent licensed ATF+4威 product.
MAINTENANCE SCHEDULES CONTENTS 䡵 Maintenance Schedule . . . . . . . . . . . . . . . . . . 534 ▫ Required Maintenance Intervals . . . . . . . . . .
M A I N T E N A N C E 534 MAINTENANCE SCHEDULES MAINTENANCE SCHEDULE The Scheduled Maintenance services listed in this manual must be done at the times or mileages specified to protect your vehicle warranty and ensure the best vehicle performance and reliability. More frequent maintenance may be needed for vehicles in severe operating conditions, such as dusty areas and very short trip driving. Inspection and service should also be done S anytime a malfunction is suspected.
MAINTENANCE SCHEDULES 535 M referring to the steps described under “Electronic Vehicle • Check the fluid levels of the coolant reservoir, brake Information Center (EVIC)/Oil Change Required” in master cylinder, power steering and transmission “Understanding Your Instrument Panel” for further in(5.7L only) and add as needed. formation. • Check all lights and other electrical items for correct operation.
M 536 MAINTENANCE SCHEDULES A I 8,000 Miles (13,000 km) or N T 6 Months Maintenance Service E Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate the tires, rotate at the first sign of C irregular wear, even if it occurs before E 8,000 miles (13 000 km). S C H E D U L E S 8 Odometer Reading Repair Order # Signature Authorized Chrysler Dealer Date Dealer Code 16,000 Miles (26,000 km) or 12 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter.
MAINTENANCE SCHEDULES 24,000 Miles (39,000 km) or 18 Months Maintenance Service Schedule 32,000 Miles (52,000 km) or 24 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 24,000 miles (39 000 km). ❏ Inspect the CV joints. ❏ Inspect exhaust system. ❏ Inspect the front and rear axle fluid, change if using your vehicle for police, taxi, fleet, off-road or frequent trailer towing.
M 538 MAINTENANCE SCHEDULES A I 40,000 Miles (65,000 km) or N T 30 Months Maintenance E Service Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate the tires, rotate at the first sign of C irregular wear, even if it occurs before E 40,000 miles (65 000 km). S C H E D U L E S 8 Odometer Reading Repair Order # Signature Authorized Chrysler Dealer Date Dealer Code 48,000 Miles (78,000 km) or 36 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter.
MAINTENANCE SCHEDULES 56,000 Miles (91,000 km) or 42 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 56,000 miles (91 000 km).
M 540 MAINTENANCE SCHEDULES A I 64,000 Miles (104,000 km) or 48 Months Maintenance Service Schedule N ❏ Change the engine oil and engine oil filter. T E ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 64,000 miles (104 000 km). N ❏ Replace the engine air cleaner filter. A ❏ Replace the air conditioning filter. N ❏ Inspect the brake linings; replace if necessary. C ❏ Replace the spark plugs (5.7L Engine).
MAINTENANCE SCHEDULES 72,000 Miles (117,000 km) or 54 Months Maintenance Service Schedule 80,000 Miles (130,000 km) or 60 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 72,000 miles (117 000 km). ❏ Inspect the CV joints. ❏ Inspect exhaust system. ❏ Inspect the front and rear axle fluid, change if using your vehicle for police, taxi, fleet, off-road or frequent trailer towing.
M 542 MAINTENANCE SCHEDULES A I 88,000 Miles (143,000 km) or N T 66 Months Maintenance E Service Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate the tires, rotate at the first sign of C irregular wear, even if it occurs before E 88,000 miles (143 000 km).
MAINTENANCE SCHEDULES 96,000 Miles (156,000 km) or 72 Months Maintenance Service Schedule ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ Change the engine oil and engine oil filter. Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 96,000 miles (156 000 km). Replace the engine air cleaner filter. Replace the air conditioning filter. Replace the spark plugs (3.6L Engine). Replace the spark plugs (5.7L Engine). Inspect and replace PCV valve if necessary.
M 544 MAINTENANCE SCHEDULES A I 104,000 Miles (169,000 km) or N T 78 Months Maintenance E Service Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate the tires, rotate at the first sign of C irregular wear, even if it occurs before E S C H E D U L E S 8 104,000 miles (169 000 km). ❏ Flush and replace the engine coolant if not done at 60 months.
MAINTENANCE SCHEDULES 120,000 Miles (195,000 km) or 90 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 120,000 miles (195 000 km). ❏ Inspect the CV joints. ❏ Inspect exhaust system. ❏ Inspect the front and rear axle fluid, change if using your vehicle for police, taxi, fleet, off-road or frequent trailer towing. ❏ Change the automatic transmission fluid and filter(s).
M 546 MAINTENANCE SCHEDULES A I 128,000 Miles (208,000 km) or 96 Months Maintenance Service N T Schedule E ❏ Change the engine oil and engine oil filter. N ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 128,000 miles (208 000 km). A N ❏ Replace the engine air cleaner filter. C ❏ Replace the air conditioning filter. E ❏ Replace the spark plugs (5.7L Engine).
MAINTENANCE SCHEDULES 144,000 Miles (234,000 km) or 108 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 144,000 miles (234 000 km). ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. ❏ Replace the air conditioning filter. ❏ Inspect the brake linings, replace if necessary. ❏ Inspect the CV joints.
M A I N T E N A N C E S C H E D U L E S 8 548 MAINTENANCE SCHEDULES † This maintenance is recommended by the manufacturer to the owner, but is not required to maintain emissions warranty. WARNING! • You can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS 䡵 Suggestions For Obtaining Service For Your Vehicle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 551 ▫ Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) . . . . . . . . . . . . 553 ▫ Prepare For The Appointment . . . . . . . . . . . 551 ▫ Service Contract . . . . . . . . . . . . . . . . . . . . . 553 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . 551 䡵 Warranty Information . . . . . . . . . . . . . . . . . .
550 IF YOU NEED CONSUMER ASSISTANCE 䡵 Department Of Transportation Uniform Tire Quality Grades . . . . . . . . . . . . . . . . . . . . . . . . 557 ▫ Treadwear . . . . . . . . . . . . . . . . . . . . . . . . . 557 ▫ Traction Grades . . . . . . . . . . . . . . . . . . . . . 557 ▫ Temperature Grades . . . . . . . . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE 551 the service advisor and list the items in order of priority. At many authorized dealers, you may obtain a rental vehicle at a minimal daily charge. If you need a rental, it Prepare For The Appointment is advisable to make these arrangements when you call If you’re having warranty work done, be sure to have the for an appointment. right papers with you. Take your warranty folder. All work to be performed may not be covered by the IF YOU NEED ASSISTANCE warranty.
552 IF YOU NEED CONSUMER ASSISTANCE This is why you should always talk to an authorized Chrysler Group LLC Customer Center dealer’s service manager first. Most matters can be re- P.O. Box 21–8004 Auburn Hills, MI 48321–8004 solved with this process. Phone: (877) 426–5337 • If for some reason you are still not satisfied, talk to the general manager or owner of the authorized dealer- Chrysler Canada Inc. Customer Center P.O. Box 1621 ship. They want to know if you need assistance.
IF YOU NEED CONSUMER ASSISTANCE Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommunication Devices for the Deaf) equipment at its customer center. Any hearing or speech impaired customer, who has access to a TDD or a conventional teletypewriter (TTY) in the United States, can communicate with the manufacturer by dialing 1–800–380–CHRY.
554 IF YOU NEED CONSUMER ASSISTANCE We appreciate that you have made a major investment when you purchased the vehicle. An authorized dealer has also made a major investment in facilities, tools, and training to assure that you are absolutely delighted with the ownership experience. You’ll be pleased with their sincere efforts to resolve any warranty issues or related concerns.
IF YOU NEED CONSUMER ASSISTANCE 555 If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your authorized dealer, and the manufacturer. In Canada If you believe that your vehicle has a safety defect, you should contact the Customer Service Department immediately.
556 IF YOU NEED CONSUMER ASSISTANCE • Service Manuals • Owner’s Manuals These comprehensive Service Manuals provide the These Owner’s Manuals have been prepared with the information that students and professional technicians assistance of service and engineering specialists to need in diagnosing/troubleshooting, problem solving, acquaint you with specific Chrysler Group LLC vemaintaining, servicing, and repairing Chrysler Group hicles. Included are starting, operating, emergency LLC vehicles.
IF YOU NEED CONSUMER ASSISTANCE DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES The following tire grading categories were established by the National Highway Traffic Safety Administration. The specific grade rating assigned by the tire’s manufacturer in each category is shown on the sidewall of the tires on your vehicle. 557 significantly from the norm due to variations in driving habits, service practices, and differences in road characteristics and climate.
558 IF YOU NEED CONSUMER ASSISTANCE Temperature Grades The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
INDEX 10
560 INDEX Adaptive Cruise Control (ACC) (Cruise Control) . . 164 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 430 Additives, Fuel . . . . . . . . . . . . . . . . . . . . . . . . . 425 Air Cleaner, Engine (Engine Air Cleaner Filter) . . . 490 Air Conditioner Maintenance . . . . . . . . . . . . . . . 493 Air Conditioning . . . . . . . . . . . . . . . . . . . . . . . . 320 Air Conditioning Controls . . . . . . . . . . . . . . . . . 320 Air Conditioning, Operating Tips . . . . . . . . . .
INDEX 561 Fluid Check . . . . . . . . . . . . . . . . . . . . . . . . . . 505 Fluid Level Check . . . . . . . . . . . . . . . . . . . 510,511 Master Cylinder . . . . . . . . . . . . . . . . . . . . . . . 505 Fluid Type . . . . . . . . . . . . . . . . . . . . . . . . . . . 509 Parking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 376 Special Additives . . . . . . . . . . . . . . . . . . . . . . 509 Warning Light . . . . . . . . . . . . . . . . . . . . . . . . 249 Torque Converter . . . . . . .
562 INDEX Cargo Area Features . . . . . . . . . . . . . . . . . . . . . . 228 Cargo Compartment . . . . . . . . . . . . . . . . . . . . . . 228 Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 229 Cargo Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . 229 Cargo Tie-Downs . . . . . . . . . . . . . . . . . . . . . . . . 232 Cargo (Vehicle Loading) . . . . . . . . . . . . . . . . . . . 433 Cellular Phone . . . . . . . . . . . . . . . . . . . . . . .
INDEX Coolant Level . . . . . . . . . . . . . Disposal of Used Coolant . . . . Drain, Flush, and Refill . . . . . . Inspection . . . . . . . . . . . . . . . Points to Remember . . . . . . . . Pressure Cap . . . . . . . . . . . . . Radiator Cap . . . . . . . . . . . . . Selection of Coolant (Antifreeze) Cruise Control (Speed Control) . . Cupholders . . . . . . . . . . . . . . . . Customer Assistance . . . . . . . . . . . . . . . . . . . . . 503 . . . . . . . . . . . . 503 . . . . . . . . . . . . 500 . . .
564 INDEX E-85 Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 426 Emission Control System Maintenance . . . . . . . . . 484 Electric Remote Mirrors . . . . . . . . . . . . . . . . . . . 109 Engine Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . 490 Electrical Outlet, Auxiliary (Power Outlet) . . . . . . 219 Block Heater . . . . . . . . . . . . . . . . . . . . . . . . . 344 Electronic Brake Control System . . . . . . . . . . . . . 378 Break-In Recommendations . . . . . . . .
INDEX 565 Engine Oil Disposal . . . . . . . . . . . . . . . . . . . . 490 Finish Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . 513 Flashers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 460 Hazard Warning . . . . . . . . . . . . . . . . . . . . . . . 460 Turn Signal . . . . . . . . . . . . . . . . . . . 97,246,525,527 Flexible Fuel Vehicles Cruising Range . . . . . . . . . . . . . . . . . . . . . . . 429 Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . .
566 INDEX Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . 487 Power Steering . . . . . . . . . . . . . . . . . . . . . . . . 375 Fluids, Lubricants and Genuine Parts . . . . . . . . . . 531 Fog Light Service . . . . . . . . . . . . . . . . . . . . . . . . 525 Fog Lights . . . . . . . . . . . . . . . . . . . . . . . . . . 246,525 Folding Rear Seat . . . . . . . . . . . . . . . . . . . . . . . . 135 Four Wheel Drive . . . . . . . . . . . . . . . . . . . . . 354,360 Operation . . . . . . . .
INDEX Gasoline, Reformulated . . . . . . . . . . . . . . . . . . . 423 Gauges Coolant Temperature . . . . . . . . . . . . . . . . . . . 253 Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 252 Speedometer . . . . . . . . . . . . . . . . . . . . . . . . . 251 Tachometer . . . . . . . . . . . . . . . . . . . . . . . . . . 244 Gear Ranges . . . . . . . . . . . . . . . . . . . . . . . . . . . 346 Gear Select Lever Override . . . . . . . . . . . . . . . . . 473 General Information . . . . . .
568 INDEX Immobilizer (Sentry Key) . . . . . . . . . . . . . . . . . . . 18 Infant Restraint . . . . . . . . . . . . . . . . . . . . . . . . 80,81 Inflation Pressure Tires . . . . . . . . . . . . . . . . . . . . 401 Information Center, Vehicle . . . . . . . . . . . . . . . . . 254 Inside Rearview Mirror . . . . . . . . . . . . . . . . . . . 106 Instrument Cluster . . . . . . . . . . . . . . . . . . . . 243,244 Instrument Panel and Controls . . . . . . . . . . . . . . 242 Instrument Panel Lens Cleaning . .
INDEX Light Bulbs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97 Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97,144 Airbag . . . . . . . . . . . . . . . . . . . . . . 73,74,79,95,244 Anti-Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . 251 Automatic Headlights . . . . . . . . . . . . . . . . . . . 145 Back-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . 527 Brake Assist Warning . . . . . . . . . . . . . . . . . . . 389 Brake Warning . . . . . . . .
570 INDEX Turn Signal . . . . . . . . . . . . . . . . . . . 97,144,525,527 Vanity Mirror . . . . . . . . . . . . . . . . . . . . . . . . . 110 Loading Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . 433 Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 396 Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Child Protection . . . . . . . . . . . . . . . . . . . . . . . . 34 Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Multi-Function Control Lever . . . . . . . . . . . . . . . 144 New Vehicle Break-In Period . . . . . . . . . . . . . . . . 92 Occupant Restraints . . . . . . . . . . . . . . . . . . . 47,72,76 Occupant Restraints (Sedan) . . . . . . . . . . . 67,68,72,75 Odometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 246 Trip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 246 Off-Pavement Driving (Off-Road) . . . . . . . . . . . . 368 Off-Road Driving (Off-Pavement) . . . . . . .
572 INDEX Parking Brake . . . . . . . . . . . . . . . . . . . . . . . . . . 376 Personal Settings . . . . . . . . . . . . . . . . . . . . . . . . 276 Pets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 Pets, Transporting . . . . . . . . . . . . . . . . . . . . . . . . 92 Phone, Cellular . . . . . . . . . . . . . . . . . . . . . . . . . 119 Phone, Hands-Free (Uconnect™) . . . . . . . . . . . . . 119 Placard, Tire and Loading Information . . . . . . . . . 396 Polishing and Waxing . .
INDEX Rear Park Sense System . . . . . . . . . . . . . . . . . . . 192 Rear Seat, Folding . . . . . . . . . . . . . . . . . . . . . . . 135 Rear Window Defroster . . . . . . . . . . . . . . . . . . . 235 Rear Window Features . . . . . . . . . . . . . . . . . . . . 234 Rear Wiper/Washer . . . . . . . . . . . . . . . . . . . . . . 234 Rearview Mirrors . . . . . . . . . . . . . . . . . . . . . . . . 106 Reclining Front Seats . . . . . . . . . . . . . . . . . . . . . 126 Recorder, Event Data . . . . . . . . .
574 INDEX Satellite Radio (Uconnect™ studios) . . . . . . . . . . . 316 Schedule, Maintenance . . . . . . . . . . . . . . . . . . . . 534 Seat Belt Reminder . . . . . . . . . . . . . . . . . . . . . . . 61 Seat Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49,95 Adjustable Upper Shoulder Anchorage . . . . . . . . 54 And Pregnant Women . . . . . . . . . . . . . . . . . . . 63 Child Restraint . . . . . . . . . . . . . . . . . . . . . . . 80,88 Extender . . . . . . . . . . . . . . . . . . . .
INDEX Shifting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 345 Automatic Transmission . . . . . . . . . . . . . . . . . 345 Shoulder Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Side Airbag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 Signals, Turn . . . . . . . . . . . . . . . . . . . 97,246,525,527 Sirius Backseat TV™ (Uconnect™ studios) . . . . . . 316 SmartBeams . . . . . . . . . . . . . . . . . . . . . . . . . . . 146 Snow Chains (Tire Chains) . . .
576 INDEX Supplemental Restraint System - Airbag . . . . . . . . 63 Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97,400,557 Air Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . 401 Suspension, Air . . . . . . . . . . . . . . . . . . . . . . . . . 362 Chains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 409 Sway Control, Trailer . . . . . . . . . . . . . . . . . . . . . 384 Changing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 461 Synthetic Engine Oil .
INDEX Snow Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . 411 Spare Tire . . . . . . . . . . . . . . . . . . . . . . . . . . . 462 Spinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . 406 Tread Wear Indicators . . . . . . . . . . . . . . . . . . . 407 Wheel Mounting . . . . . . . . . . . . . . . . . . . . . . 467 Tongue Weight/Trailer Weight . . . . . . . . . . . . . . 443 Torque Converter Clutch . . . . . . . . . . . . . . . . . . 352 Tow Hooks, Emergency . . . . . . . . . . . . .
578 INDEX UCI Connector . . . . . . . . . . . . . . . . . . . . . . . . . 309 Uconnect™ (Hands-Free Phone) . . . . . . . . . . . . . 119 Uniform Tire Quality Grades . . . . . . . . . . . . . . . . 557 Universal Consumer Interface (UCI) Connector . . . 309 Universal Transmitter . . . . . . . . . . . . . . . . . . . . . 206 Untwisting Procedure, Seat Belt . . . . . . . . . . . . . . 53 Upholstery Care . . . . . . . . . . . . . . . . . . . . . . . . 515 Vanity Mirrors . . . . . . . . . . . . . . . . . . . .
Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Windshield Defroster . . . . . . . . . . . . . . . . . . . 95,322 Windshield Washers . . . . . . . . . . . . . . . . . . . . . . 153 Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 496 Windshield Wiper Blades Windshield Wipers . . . . . Wipers, Intermittent . . . . Wipers, Rain Sensitive . . . . . . . . . . . . . . . . . . . . . . . . . . .
VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name Chrysler Group LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefore. DRIVING AND ALCOHOL Drunken driving is one of the most frequent causes of accidents. Your driving ability can be seriously impaired with blood alcohol levels far below the legal minimum. If you are drinking, don’t drive. Ride with a designated non-drinking driver, call a cab, a friend, or use public transportation.
Chrysler Group LLC 10WK741-126-AD Fourth Edition Printed in U.S.A.
