2016 OWNER’S MANUAL 200
VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name FCA US LLC shall be deemed to be deleted and the name FCA Canada Inc. used in substitution therefore. DRIVING AND ALCOHOL Drunken driving is one of the most frequent causes of accidents. Your driving ability can be seriously impaired with blood alcohol levels far below the legal minimum. If you are drinking, don’t drive. Ride with a designated nondrinking driver, call a cab, a friend, or use public transportation.
SECTION TABLE OF CONTENTS PAGE 1 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113 3 4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION CONTENTS 䡵 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . .4 䡵 VEHICLE IDENTIFICATION NUMBER . . . . . . . .6 䡵 HOW TO USE THIS MANUAL . . . . . . . . . . . . . .4 䡵 VEHICLE MODIFICATIONS/ALTERATIONS . . . .7 䡵 WARNINGS AND CAUTIONS . . . . . . . . . . . . . .
4 INTRODUCTION When it comes to service, remember that your authorized dealer knows your vehicle best, has factory-trained techCongratulations on selecting your new FCA US LLC nicians and genuine MOPAR® parts, and cares about vehicle. Be assured that it represents precision workmanyour satisfaction. ship, distinctive styling, and high quality - all essentials that are traditional to our vehicles.
INTRODUCTION 5 1
6 INTRODUCTION WARNINGS AND CAUTIONS This Owner’s Manual contains WARNINGS against operating procedures that could result in a collision or bodily injury. It also contains CAUTIONS against procedures that could result in damage to your vehicle. If you do not read this entire Owner’s Manual, you may miss important information. Observe all Warnings and Cautions.
INTRODUCTION 7 VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death. Stamped VIN Location NOTE: It is illegal to remove or alter the VIN.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS 䡵 A WORD ABOUT YOUR KEYS . . . . . . . . . . . . .12 䡵 VEHICLE SECURITY ALARM — IF EQUIPPED . . .19 ▫ Keyless Push Button Ignition . . . . . . . . . . . . . .12 ▫ Rearming Of The System . . . . . . . . . . . . . . . .19 ▫ Key Fob . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 ▫ To Arm The System . . . . . . . . . . . . . . . . . . . .19 ▫ Ignition Or Accessory On Message . . . . . . . . . .15 ▫ To Disarm The System . . . . . . . . . . .
10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ To Unlatch The Trunk . . . . . . . . . . . . . . . . . . .24 ▫ General Information . . . . . . . . . . . . . . . . . . . .40 ▫ Using The Panic Alarm . . . . . . . . . . . . . . . . . .24 䡵 WINDOWS . . . . . . . . . . . . . . . . . . . . . . . . . . .41 ▫ Programming Additional Transmitters . . . . . . .25 ▫ Power Windows . . . . . . . . . . . . . . . . . . . . . . .41 ▫ Transmitter Battery Replacement . . . . . . . . . . .25 ▫ Wind Buffeting . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 䡵 ENGINE BREAK-IN RECOMMENDATIONS . . .107 䡵 SAFETY TIPS . . . . . . . . . . . . . . . . . . . . . . . . .108 ▫ Transporting Passengers . . . . . . . . . . . . . . . . .108 ▫ Exhaust Gas . . . . . . . . . . . . . . . . . . . . . . . . .109 ▫ Safety Checks You Should Make Inside The Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . .110 ▫ Periodic Safety Checks You Should Make Outside The Vehicle . . . . . . . . . . . . . . . . . . . . . . . . .
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The Keyless Push Button Ignition has four operating positions, three of which are labeled and will illuminate Your vehicle uses a keyless ignition system. This system when in position. The three positions are: OFF, ACC, and consists of a Key Fob with Remote Keyless Entry (RKE) ON/RUN. The fourth position is START. During start, transmitter and a Keyless Push Button Ignition. ON/RUN will illuminate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 Key Fob The Key Fob also contains the Remote Keyless Entry (RKE) transmitter and an emergency key, which stores in the rear of the Key Fob. The emergency key allows for entry into the vehicle should the battery in the vehicle or the Key Fob go dead. The emergency key is also for locking/unlocking the glove compartment. You can keep the emergency key with you when valet parking.
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Mechanical Latch On The Back Of The Key Fob Emergency Key Removal NOTE: You can insert the double-sided emergency key into the lock cylinders with either side up.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 Ignition Or Accessory On Message When opening the driver’s door when the ignition is in ACC or ON (engine not running), a chime will sound to remind you to cycle the ignition to OFF. In addition to the chime, the ignition or accessory on message will display in the cluster.
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) A child could operate power windows, other controls, or move the vehicle. • Do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. CAUTION! An unlocked car is an invitation to thieves. Always remove the Key Fob from vehicle, place the ignition in the OFF position and lock all doors when leaving the vehicle unattended.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 The system uses a Key Fob with a factory-mated Remote Keyless Entry (RKE) transmitter, a Keyless Push Button Ignition, and a RF receiver to prevent unauthorized vehicle operation. Therefore, only Key Fobs that are programmed to the vehicle can be used to start and operate the vehicle. The system will not allow the engine to crank if an invalid Key Fob is used to start and operate the vehicle.
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: When having the Sentry Key Immobilizer System serviced, bring all vehicle keys with you to an NOTE: Only Key Fobs that are programmed to the authorized dealer. vehicle electronics can be used to start and operate the vehicle. Once a Key Fob is programmed to a vehicle, it Customer Key Programming cannot be programmed to any other vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 NOTE: Changes or modifications not expressly approved To Arm The System by the party responsible for compliance could void the Follow these steps to arm the Vehicle Security Alarm: user’s authority to operate the equipment. 1. Make sure the vehicle ignition is cycled to the ⬙OFF⬙ VEHICLE SECURITY ALARM — IF EQUIPPED position (refer to ⬙Starting Procedures⬙ in ⬙Starting And Operating⬙ for further information).
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The Vehicle Security Alarm remains armed during power trunk entry. Pushing the trunk button will not The Vehicle Security Alarm can be disarmed using any of disarm the Vehicle Security Alarm. If someone enters the following methods: the vehicle through the trunk and opens any door the • Push the UNLOCK button on the Remote Keyless alarm will sound. Entry (RKE) transmitter.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 exterior lights will flash, and the horn will sound. If this occurs, disarm the Vehicle Security Alarm. 2 Tamper Alert If something has triggered the Vehicle Security Alarm in your absence, the horn will sound three times, and the exterior lights blink three times when you unlock the doors. Check the vehicle for tampering. Security System Manual Override The Vehicle Security Alarm will not arm if you lock the doors using the manual door lock.
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE This feature also turns on the approach lighting in the outside mirrors (if equipped). Refer to “Mirrors” in “Understanding The Features Of Your Vehicle” for further information. REMOTE KEYLESS ENTRY (RKE) The RKE system allows you to lock or unlock the doors, open the trunk, or activate the Panic Alarm from distances up to approximately 66 ft (20 m) using a hand-held The lights will fade to off after approximately 30 seconds, Key Fob with RKE transmitter.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 If the vehicle is equipped with Passive Entry, refer to “Keyless Enter-N-Go” under “Things To Know Before Starting Your Vehicle” for further information. 1st Press Of Key Fob Unlocks This feature lets you program the system to unlock either the driver’s door or all doors on the first push of the UNLOCK button on the RKE transmitter. To change the current setting, refer to “Uconnect Settings” in “Understanding Your Instrument Panel” for further information.
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE turned on or turned off. To change the current setting, refer to “Uconnect Settings” in “Understanding Your This feature activates the headlights for up to 90 seconds Instrument Panel” for further information. when the doors are unlocked with the RKE transmitter. The time for this feature is programmable on vehicles To Unlatch The Trunk equipped through Uconnect.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 The Panic Alarm will stay on for three minutes unless Transmitter Battery Replacement you turn it off by either pushing the PANIC button a The recommended replacement battery is one CR2032 second time or drive the vehicle at a speed of 15 MPH battery. (24 km/h) or greater. NOTE: NOTE: • Perchlorate Material — special handling may apply. • The interior lights will turn off if you place the ignition See www.dtsc.ca.
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Emergency Key Removal Separating The RKE Transmitter Case 2. Insert the tip of the emergency key or a #2 flat blade 3. Remove the battery by turning the back cover over screwdriver into the slot and gently pry the two halves (battery facing downward) and tapping it lightly on a of the RKE transmitter apart. Make sure not to damage solid surface such as a table or similar, then replace the the seal during removal. battery.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 new battery with your fingers. Skin oils may cause NOTE: Changes or modifications not expressly approved battery deterioration. If you touch a battery, clean it by the party responsible for compliance could void the user’s authority to operate the equipment. with rubbing alcohol. 4. To assemble the RKE transmitter case, snap the two REMOTE STARTING SYSTEM — IF EQUIPPED halves together.
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE How To Use Remote Start All of the following conditions must be met before the engine will remote start: • Vehicle in PARK • Doors closed • Hood closed • Trunk closed • Hazard switch off • Brake switch inactive (brake pedal not pushed) • Battery at an acceptable charge level • RKE panic button not pushed WARNING! • Do not start or run an engine in a closed garage or confined area. Exhaust gas contains Carbon Monoxide (CO) which is odorless and colorless.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 • Remote Start Aborted — Hood Open • Remote Start Aborted — Trunk Open • Remote Start Aborted — Fuel Low • Remote Start Disabled — Start To Reset • Remote Start Aborted — Too Cold • Remote Start Aborted — Time Expired (if programmed). Then, the engine will start and the vehicle will remain in the Remote Start mode for a 15-minute cycle. NOTE: • If an engine fault is present or fuel level is low, the vehicle will start and then shut down in 10 seconds.
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Exit Remote Start Mode Without Driving The General Information Vehicle The following regulatory statement applies to all radio Push and release the REMOTE START button one time or frequency (RF) devices equipped in this vehicle: allow the engine to run for the entire 15-minute cycle. This device complies with Part 15 of the FCC Rules and NOTE: To avoid unintentional shutdowns, the system will with Industry Canada licence-exempt RSS standard(s).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 DOOR LOCKS Manual Door Locks 2 To lock each door, rotate the door lock knob on each door trim panel forward. To unlock the front doors, pull the inside door handle to the first detent or rotate the door lock button until the red indicator is visible. To unlock the rear doors, rotate the door lock button until the red indicator is visible.
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: The manual door locks will not lock or unlock the trunk. WARNING! • For personal security and safety in the event of a collision, lock the vehicle doors before you drive as well as when you park and leave the vehicle. • Never use the PARK position as a substitute for the parking brake. Always apply the parking brake fully when parked to guard against vehicle movement and possible injury or damage.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 Power Door Locks A power door lock switch is located on each of the front door trim panels. Use this switch to lock or unlock the doors and trunk. 2 The doors can also be locked and unlocked with the Keyless Enter-N-Go (Passive Entry) system. Refer to “Keyless Enter-N-Go” in “Things To Know Before Starting Your Vehicle” for further information.
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE the ignition is in the ACC or ON/RUN position, a chime 3. The driver door is opened. will sound as a reminder to remove the Key Fob. 4. The doors were not previously unlocked. Automatic Door Locks — If Equipped Automatic Unlock Doors On Exit Programming The auto door lock feature default condition is enabled.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 2. Insert the tip of the emergency key or similar flatbladed object into the lock and rotate clockwise approximately one-quarter turn to the lock position or counter clockwise to the unlock position (as indicated by the stamped icons). 2 3. Repeat steps 1 and 2 for the opposite rear door. Unlock Child Protection Door Lock WARNING! Lock Child Protection Door Lock Avoid trapping anyone in a vehicle in a collision.
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: For emergency exit with the system engaged, NOTE: pull the toggle lock by the door handle (UNLOCKED • Passive Entry may be programmed ON/OFF. Refer to position), roll down the window, and open the door with “Uconnect Settings” in “Understanding Your Instruthe outside door handle. ment Panel” for further information.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 To Unlock From The Driver’s Side With a valid Passive Entry RKE transmitter within 5 ft (1.5 m) of the driver’s door handle, grab the front driver door handle to unlock the driver’s door automatically. The interior door panel lock knob will toggle when the door is unlocked. NOTE: If “1st Press of Key Fob Unlocks All Doors” is programmed, all doors will unlock when you grab hold of the drivers door handle.
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Preventing Inadvertent Locking Of Passive Entry RKE When any of these situations occur, after all open doors are Transmitter In Vehicle shut, the FOBIK-Safe search will be executed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 To Enter The Trunk With a valid Passive Entry RKE transmitter within 3 ft (1.0 m) of the decklid, push the button located on the light bar between the license plate lamps. 2 NOTE: If you inadvertently leave your vehicle’s Passive Entry RKE transmitter in the trunk and try to close the decklid, the decklid will automatically unlatch, unless another one of the vehicle’s Passive Entry RKE transmitters is outside the vehicle and within 3 ft (1.
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The Passive Entry system will not operate if the RKE transmitter battery is dead. The vehicle doors can also be locked by using the RKE transmitter lock button or the lock button located on the vehicle’s interior door panel.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 NOTE: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. 2 WINDOWS Power Windows The window controls on the driver’s door control all the door windows.
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE There are single window controls on each passenger door trim panel, which operate the passenger door windows. The window controls will operate only when the ignition is in the ACC or ON/RUN position. WARNING! (Continued) location accessible to children. Occupants, particularly unattended children, can become entrapped by the windows while operating the power window switches. Such entrapment may result in serious injury or death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 Front Windows Express Up And Down — If Equipped NOTE: • If the window runs into any obstacle during autoclosure, it will reverse direction and then go back down. Remove the obstacle and use the window Push the switch to the second detent and release. The switch again to close the window. window will go down automatically.
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE the DOWN position). To enable the window controls, push and release the window lockout button again Should the Auto Up feature stop working, the window (setting it in the UP position). may need to be reset. To reset Auto Up: Wind Buffeting 1. Make sure the door is fully closed. Wind buffeting can be described as the perception of 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 TRUNK LOCK AND RELEASE NOTE: The transmission must be in PARK before the button will operate. The trunk lid can be released from outside the vehicle by pushing the TRUNK button on the Remote Keyless Entry (RKE) transmitter twice within five seconds or by using the external release switch located on the underside of the decklid overhang. The release feature will function only when the vehicle is in the unlock condition.
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE TRUNK SAFETY WARNING WARNING! Do not allow children to have access to the trunk, either by climbing into the trunk from outside, or through the inside of the vehicle. Always close the trunk lid when your vehicle is unattended. Once in the trunk, young children may not be able to escape, even if they entered through the rear seat. If trapped in the trunk, children can die from suffocation or heat stroke.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 2. If a child from 2 to 12 years old (not in a rear-facing child restraint) must ride in the front passenger seat, Some of the most important safety features in your move the seat as far back as possible and use the vehicle are the restraint systems: proper child restraint. (Refer to “Child Restraints”) • Seat Belt Systems 3.
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 6. All occupants should always wear their lap and shoulder belts properly. 7. The driver and front passenger seats should be moved back as far as practical to allow the Advanced Front Air Bags room to inflate. WARNING! • Never place a rear-facing child restraint in front of an air bag. A deploying passenger Advanced Front Air Bag can cause death or serious injury to a child 12 years or younger, including a child in a rearfacing child restraint.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 ejection and the risk of injury caused by striking the position the Seat Belt Reminder Light will turn on and inside of the vehicle. Everyone in a motor vehicle should remain on until both outboard front seat belts are buckled. The outboard front passenger seat BeltAlert is not active be belted at all times. when an outboard front passenger seat is unoccupied.
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Change Of Status If the driver or outboard front seat passenger (if equipped with outboard front passenger seat BeltAlert) unbuckles their seat belt while the vehicle is traveling, the BeltAlert warning sequence will begin until the seat belts are buckled again. The outboard front passenger seat BeltAlert is not active when the outboard front passenger seat is unoccupied.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 WARNING! WARNING! (Continued) • Relying on the air bags alone could lead to more severe injuries in a collision. The air bags work with your seat belt to restrain you properly. In some collisions, the air bags won’t deploy at all. Always wear your seat belt even though you have air bags. • In a collision, you and your passengers can suffer much greater injuries if you are not properly buckled up.
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) WARNING! (Continued) • A lap belt worn too high can increase the risk of injury in a collision. The seat belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap part of your seat belt as low as possible and keep it snug. • A twisted seat belt may not protect you properly. In a collision, it could even cut into you. Be sure the seat belt is flat against your body, without twists.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 WARNING! (Continued) • A frayed or torn seat belt could rip apart in a collision and leave you with no protection. Inspect the seat belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the seat belt system. Seat belt assemblies must be replaced after a collision. 2 Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door.
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Inserting Latch Plate Into Buckle Positioning The Lap Belt 4. Position the lap belt so that it is snug and lies low 5. Position the shoulder belt across the shoulder and across your hips, below your abdomen. To remove chest with minimal, if any slack so that it is comfortslack in the lap belt portion, pull up on the shoulder able and not resting on your neck. The retractor will belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 6. To release the belt, push the red button on the buckle. 3. Slide the latch plate upward over the folded webbing. The folded webbing must enter the slot at the top of The seat belt will automatically retract to its stowed the latch plate. position. If necessary, slide the latch plate down the webbing to allow the seat belt to retract fully. 4. Continue to slide the latch plate up until it clears the folded webbing and the seat belt is no longer twisted.
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: The adjustable upper shoulder belt anchorage is equipped with an Easy Up feature. This feature allows the shoulder belt anchorage to be adjusted in the upward position without pushing or squeezing the release button. To verify the shoulder belt anchorage is latched, pull downward on the shoulder belt anchorage until it is locked into position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 WARNING! Seat Belts And Pregnant Women • ONLY use a Seat Belt Extender if it is physically required in order to properly fit the original seat belt system. DO NOT USE the Seat Belt Extender if, when worn, the distance between the front edge of the Seat Belt Extender buckle and the center of the occupant’s body is LESS than 6 inches. • Using a Seat Belt Extender when not needed can increase the risk of serious injury or death in a collision.
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Position the lap belt snug and low below the abdomen and across the strong bones of the hips. Place the shoulder belt across the chest and away from the neck. Never place the shoulder belt behind the back or under the arm . Seat Belt Pretensioner The front seat belt system is equipped with pretensioning devices that are designed to remove slack from the seat belt in the event of a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 Restraints” section of this manual. The table below around the occupant’s mid-section so as to not activate defines the type of feature for each seating position. the ALR. If the ALR is activated, you will hear a clicking sound as the seat belt retracts. Allow the webbing to retract completely in this case and then carefully pull out only the amount of webbing necessary to comfortably wrap around the occupant’s mid-section.
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Never place a rear-facing child restraint in front of an air bag. A deploying Passenger Advanced Front Air Bag can cause death or serious injury to a child 12 years or younger, including a child in a rearfacing child restraint. • Only use a rear-facing child restraint in a vehicle with a rear seat. How To Engage The Automatic Locking Mode 1. Buckle the combination lap and shoulder belt. 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 WARNING! (Continued) • Do not use the Automatic Locking Mode to restrain occupants who are wearing the seat belt or children who are using booster seats. The locked mode is only used to install rear-facing or forward-facing child restraints that have a harness for restraining the child.
62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Advanced Front Air Bags This vehicle has Advanced Front Air Bags for both the driver and front passenger as a supplement to the seat belt restraint systems. The driver’s Advanced Front Air Bag is mounted in the center of the steering wheel. The passenger’s Advanced Front Air Bag is mounted in the instrument panel, above the glove compartment. The words “SRS AIRBAG” or “AIRBAG” are embossed on the air bag covers.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 WARNING! • Being too close to the steering wheel or instrument panel during Advanced Front Air Bag deployment could cause serious injury, including death. Air bags need room to inflate. Sit back, comfortably extending your arms to reach the steering wheel or instrument panel. • Never place a rear-facing child restraint in front of an air bag.
64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Advanced Air Bag Features WARNING! (Continued) This vehicle is equipped with a right front passenger Occupant Classification System (“OCS”) that is designed to provide Passenger Advanced Front Air Bag output appropriate to the occupant’s seated weight input, as determined by the OCS.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 vehicle damage — for example, some pole collisions, The steering wheel hub trim cover and the upper right side of the instrument panel separate and fold out of the truck underrides, and angle offset collisions. way as the air bags inflate to their full size. The Advanced On the other hand, depending on the type and location of Front Air Bags fully inflate in less time than it takes to impact, Advanced Front Air Bags may deploy in crashes blink your eyes.
66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Occupant Classification Module (OCM) and Sensor • The front passenger seat is occupied by a small passenger, including a child; or The Occupant Classification Module (OCM) is located underneath the front passenger seat. The Sensor is lo- • The front passenger seat is occupied by a rear-facing cated beneath the passenger seat cushion foam. Any child restraint; or weight on the seat will be sensed by the Sensor.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 Front Passenger Seat Occupant Status Properly seated adult Unoccupied seat Front Passenger Air Bag Output Full-power deployment OR reduced-power deployment Reduced-power deployment WARNING! • Never place a rear-facing child restraint in front of an air bag. A deploying Passenger Advanced Front Air Bag can cause death or serious injury to a child 12 years or younger, including a child in a rearfacing child restraint.
68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE In order for the OCS to operate as designed, it is important for the front passenger to be seated properly and properly wearing the seat belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 Do not decrease OR increase the front passenger’s Examples of improper front passenger seating include: seated weight on the front passenger seat • The front passenger’s weight is transferred to another part of the vehicle (like the door, arm rest or instruThe front passenger’s seated weight must be properly ment panel). positioned on the front passenger seat. Failure to do so may result in serious injury or death.
70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Anything that may decrease or increase the front passenger’s seated weight. The OCS determines the front passenger’s most probable classification.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 2 Not Seated Properly Not Seated Properly
72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) Not Seated Properly WARNING! • If an occupant in the front passenger seat is seated improperly, the occupant may provide an output (Continued) signal to the OCS that is different from the occupant’s properly seated weight input. This may result in serious injury or death in a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 WARNING! (Continued) properly, which may result in serious injury or death in a collision. Do not place any objects on the floor under the front passenger seat. Do not make any modifications to the front passenger seat components, assembly, or to the seat cover. If the seat, trim cover, or cushion needs service for any reason, take the vehicle to your authorized dealer. Only FCA LLC approved seat accessories may be used.
74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • At no time should any Supplemental Restraint System (SRS) component or SRS related component or fastener be modified or replaced with any part except those which are approved by FCA US LLC. WARNING! Unapproved modifications or service procedures to the passenger seat assembly, its related components, seat cover or cushion may inadvertently change the air bag deployment in case of a frontal collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 Supplemental Driver And Front Passenger Knee Air Bags This vehicle is equipped with a Supplemental Driver Knee Air Bag mounted in the instrument panel below the steering column and a Supplemental Passenger Knee Air Bag mounted in the instrument panel below the glove compartment. The Supplemental Knee Air Bags provide enhanced protection during a frontal impact by working together with the seat belts, pretensioners, and Advanced Front Air Bags.
76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE through the seat seam into the space between the occupant and the door. The SAB moves at a very high speed and with such a high force that it could injure occupants if they are not seated properly, or if items are positioned in the area where the SAB inflates. Children are at an even greater risk of injury from a deploying air bag.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77 injury reduction potential provided by the seat belts and body structure. The SABICs deploy downward, covering the side windows. An inflating SABIC pushes the outside edge of the trim out of the way and covers the window. The SABICs inflate with enough force to injure occupants if they are not belted and seated properly, or if items are positioned in the area where the SABICs inflate. Children are at an even greater risk of injury from a deploying air bag.
78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The SABICs and SABs (“Side Air Bags”) are designed to activate in certain side impacts and certain rollover events. The Occupant Restraint Controller (“ORC”) determines whether the deployment of the Side Air Bags in a particular side impact or rollover event is appropriate, based on the severity and type of collision. Vehicle damage by itself is not a good indicator of whether or not Side Air Bags should have deployed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 79 WARNING! (Continued) properly. In some collisions, Side Air Bags won’t deploy at all. Always wear your seat belt even though you have Side Air Bags. The Side Air Bags will not deploy in all side collisions, including some collisions at certain angles, or some side collisions that do not impact the area of the passenger compartment. The Side Air Bags may deploy during angled or offset frontal collisions where the Advanced Front Air Bags deploy.
80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE faster-developing event may deploy the seat belt pretensioners as well as the Side Air Bags on both sides of the vehicle. The rollover sensing-system may also deploy the seat belt pretensioners, with or without the Side Air Bags, on both sides of the vehicle if the vehicle experiences a near rollover event. If A Deployment Occurs deploy and unfold.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 81 Do not drive your vehicle after the air bags have de- Enhanced Accident Response System ployed. If you are involved in another collision, the air In the event of an impact, if the communication network bags will not be in place to protect you.
82 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Enhanced Accident Response System Reset Procedure the OFF position or in the ACC position, the air bag system is not on and the air bags will not inflate. In order to reset the Enhanced Accident Response System functions after an event, the ignition switch must be changed from ignition START or ON/RUN to ignition OFF.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 83 While the air bag system is designed to be maintenance free, if any of the following occurs, have an authorized dealer service the air bag system immediately. • The Air Bag Warning Light does not come on during the four to eight seconds when the ignition switch is first turned to the ON/RUN position. • The Air Bag Warning Light remains on after the four to eight-second interval.
84 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Warning Light has come on and a fault has been detected. If the Redundant Air Bag Warning Light comes on intermittently or remains on while driving have an authorized dealer service the vehicle immediately. For additional information regarding the Redundant Air Bag Warning Light refer to the “Instrument Panel” section of this manual.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 85 These data can help provide a better understanding of This vehicle is equipped with an event data recorder the circumstances in which crashes and injuries occur. (EDR).
86 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Child Restraints WARNING! (Continued) Everyone in your vehicle needs to be buckled up at all times, including babies and children. great that you could not hold the child, no matter how strong you are. The child and others could be badly injured. Any child riding in your vehicle should be in a proper restraint for the child’s size. Every state in the United States, and every Canadian province, requires that small children ride in proper restraint systems.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 87 • Canadian residents should refer to Transport Canada’s website for additional information: www.tc.gc.ca/eng/ • For additional information, refer to www.seatcheck.org or motorvehiclesafety/safedrivers-childsafety-index-53.htm call 1–866–732–8243.
88 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Larger Children Children Too Large for Child Restraints Child Size, Height, Weight Or Age Children who have out-grown their forward-facing child restraint, but are too small to properly fit the vehicle’s seat belt Children 12 years old or younger, who have out-grown the height or weight limit of their booster seat Infants And Child Restraints Safety experts recommend that children ride rear-facing in the vehicle until they are two years old or until they re
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 89 WARNING! • Never place a rear-facing child restraint in front of an air bag. A deploying passenger Advanced Front Air Bag can cause death or serious injury to a child 12 years or younger, including a child in a rearfacing child restraint. • Only use a rear-facing child restraint in a vehicle with a rear seat.
90 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) directions exactly when installing an infant or child restraint. • After a child restraint is installed in the vehicle, do not move the vehicle seat forward or rearward because it can loosen the child restraint attachments. Remove the child restraint before adjusting the vehicle seat position. When the vehicle seat has been adjusted, reinstall the child restraint.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 91 4. Is the lap part of the belt as low as possible, touching the child’s thighs and not their stomach? 5. Can the child stay seated like this for the whole trip? If the answer to any of these questions was “no,” then the child still needs to use a booster seat in this vehicle. If the child is using the lap/shoulder belt, check seat belt fit periodically and make sure the seat belt buckle is latched.
92 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Recommendations For Attaching Child Restraints Restraint Type Combined Weight of the Child + Child Restraint Rear-Facing Child Restraint Rear-Facing Child Restraint Forward-Facing Child Restraint Forward-Facing Child Restraint Up to 65 lbs (29.5 kg) More than 65 lbs (29.5 kg) Up to 65 lbs (29.5 kg) More than 65 lbs (29.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 93 Lower Anchors And Tethers For CHildren (LATCH) Restraint System Your vehicle is equipped with the child restraint anchorage system called LATCH, which stands for Lower Anchors and Tethers for CHildren. The LATCH system has three vehicle anchor points for installing LATCHequipped child seats. There are two lower anchorages located at the back of the seat cushion where it meets the seatback and one top tether anchorage located behind the seating position.
94 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE LATCH Positions For Installing Child Restraints In This Vehicle • • Lower Anchorage Symbol : 2 anchorages per seating position Top Tether Anchorage Symbol
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 95 Frequently Asked Questions About Installing Child Restraints With LATCH What is the weight limit (child’s 65 lbs (29.5 kg) Use the LATCH anchorage system unweight + weight of the child restraint) til the combined weight of the child for using the LATCH anchorage sysand the child restraint is 65 lbs tem to attach the child restraint? (29.5 kg).
96 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Frequently Asked Questions About Installing Child Restraints With LATCH Can two child restraints be attached No Never “share” a LATCH anchorage using a common lower LATCH anwith two or more child restraints. If chorage? the center position does not have dedicated LATCH lower anchorages, use the seat belt to install a child seat in the center position next to a child seat using the LATCH anchorages in an outboard position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 97 Locating LATCH Anchorages The lower anchorages are round bars that are found at the rear of the seat cushion where it meets the seatback, below the anchorage symbols on the seatback. They are just visible when you lean into the rear seat to install the child restraint. You will easily feel them if you run your finger along the gap between the seatback and seat cushion.
98 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Locating Tether Anchorages There are tether strap anchorages behind each rear seating position located in the panel between the rear seatback and the rear window. They are found under a plastic cover with the tether anchorage symbol on it. Tether Strap Anchorages LATCH-compatible child restraint systems will be equipped with a rigid bar or a flexible strap on each side.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 99 tether strap. The tether strap will have a hook at the end to attach to the top tether anchorage and a way to tighten the strap after it is attached to the anchorage. Center Seat LATCH WARNING! (Continued) seat belt for installing child seats in the outboard positions. Please refer to “Installing The LATCHCompatible Child Restraint System” for typical installation instructions.
100 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 1. Loosen the adjusters on the lower straps and on the 4. If the child restraint has a tether strap, connect it to the tether strap of the child seat so that you can more top tether anchorage. See the section “Installing Child Restraints Using the Top Tether Anchorage” for direceasily attach the hooks or connectors to the vehicle tions to attach a tether anchor. anchorages. 2. Place the child seat between the lower anchorages for 5.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 101 How To Stow An Unused ALR Seat Belt: When using the LATCH attaching system to install a child restraint, stow all ALR seat belts that are not being used by other occupants or being used to secure child restraints. An unused belt could injure a child if they play with it and accidentally lock the seat belt retractor. Before installing a child restraint using the LATCH system, buckle the seat belt behind the child restraint and out of the child’s reach.
102 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Installing Child Restraints Using The Vehicle Seat Belt Lap/Shoulder Belt Systems For Installing Child Restraints In This Vehicle The seat belts in the passenger seating positions are equipped with a Switchable Automatic Locking Retractor (ALR) that is designed to keep the lap portion of the seat belt tight around the child restraint so that it is not necessary to use a locking clip.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 103 Frequently Asked Questions About Installing Child Restraints With Seat Belts What is the weight limit (child’s Weight limit of the Child Restraint Always use the tether anchor when weight + weight of the child reusing the seat belt to install a forstraint) for using the Tether Anchor ward facing child restraint, up to with the seat belt to attach a forthe recommended weight limit of ward facing child restraint? the child restraint.
104 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 5. To lock the seat belt, pull down on the shoulder part of the belt until you have pulled all the seat belt webbing out of the retractor. Then, allow the webbing to retract Place the child seat in the center of the seating back into the retractor. As the webbing retracts, you position. For some second row seats, you may need to will hear a clicking sound.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 105 9. Test that the child restraint is installed tightly by pulling back and forth on the child seat at the belt path. It should not move more than 1 inch (25.4 mm) in any direction. WARNING! (Continued) (LATCH) Restraint System” for the location of approved tether anchorages in your vehicle. Any seat belt system will loosen with time, so check the belt occasionally, and pull it tight if necessary.
106 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Rotate or lift the cover to access the anchor directly behind the seat where you are placing the child restraint. 3. Route the tether strap to provide the most direct path for the strap between the anchor and the child seat. If your vehicle is equipped with adjustable rear head restraints, raise the head restraint, and where possible, route the tether strap under the head restraint and between the two posts.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 107 5. Remove slack in the tether strap according to the child Transporting Pets restraint manufacturer’s instructions. Air Bags deploying in the front seat could harm your pet. An unrestrained pet will be thrown about and possibly WARNING! injured, or injure a passenger during panic braking or in • An incorrectly anchored tether strap could lead to a collision. increased head motion and possible injury to the child.
108 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE While cruising, brief full-throttle acceleration within the SAFETY TIPS limits of local traffic laws contributes to a good break-in. Transporting Passengers Wide-open throttle acceleration in low gear can be detriNEVER TRANSPORT PASSENGERS IN THE CARGO mental and should be avoided. The engine oil installed in the engine at the factory is a AREA. high-quality energy conserving type lubricant.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 109 Exhaust Gas WARNING! (Continued) WARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (CO), follow these safety tips: • Do not run the engine in a closed garage or in confined areas any longer than needed to move your vehicle in or out of the area.
110 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE have the system inspected at an authorized dealer as soon as possible. This light will illuminate with a single chime when a fault with the Air Bag Warning Seat Belts Light has been detected, it will stay on until the fault Inspect the seat belt system periodically, checking for is cleared. If the light comes on intermittently or cuts, frays, and loose parts. Damaged parts must be remains on while driving, have an authorized dealer replaced immediately.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 111 unobstructed and that are firmly secured so that they cannot slip out of position and interfere with the pedals or impair safe operation of your vehicle in other ways. WARNING! Pedals that cannot move freely can cause loss of vehicle control and increase the risk of serious personal injury. • Always make sure that floor mats are properly attached to the floor mat fasteners.
112 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Periodic Safety Checks You Should Make Outside The Vehicle Door Latches Tires Fluid Leaks Examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread or sidewall. Inspect the tread for cuts and cracks. Inspect sidewalls for cuts, cracks, and bulges. Check the wheel nuts for tightness. Check the tires (including spare) for proper cold inflation pressure.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 䡵 MIRRORS . . . . . . . . . . . . . . . . . . . . . . . . . . . .120 ▫ Heated Mirrors — If Equipped . . . . . . . . . . .130 ▫ Inside Day/Night Mirror — If Equipped . . . .120 ▫ Illuminated Vanity Mirrors — If Equipped . . .131 ▫ Automatic Dimming Mirror — If Equipped . . .121 䡵 BLIND SPOT MONITORING (BSM) — IF EQUIPPED . . . . . . . . . . . . . . . . . . . . . . ▫ Outside Mirrors . . . . . . . . . . . . . . . . . . . . . .128 ▫ Rear Cross Path. . . .
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Front Heated Seats — If Equipped . . . . . . . . .146 ▫ Automatic Headlights — If Equipped . . . . . . .160 ▫ Front Ventilated Seats — If Equipped . . . . . . .147 ▫ Headlights On With Wipers (Available With Automatic Headlights Only) . . . . . . . . . . . . .160 ▫ Head Restraints . . . . . . . . . . . . . . . . . . . . . .148 ▫ Folding Rear Seat . . . . . . . . . . . . . . . . . . . . .152 䡵 DRIVER MEMORY SEAT — IF EQUIPPED . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 ▫ Front Map/Reading Lights . . . . . . . . . . . . . .166 ▫ To Activate . . . . . . . . . . . . . . . . . . . . . . . . . .178 ▫ Interior Lights . . . . . . . . . . . . . . . . . . . . . . .167 ▫ To Set A Desired Speed . . . . . . . . . . . . . . . . .179 ▫ Battery Saver Feature . . . . . . . . . . . . . . . . . .169 ▫ To Deactivate . . . . . . . . . . . . . . . . . . . . . . . .179 䡵 WINDSHIELD WIPERS AND WASHERS . . . . . .170 ▫ To Resume Speed . . .
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ To Turn Off . . . . . . . . . . . . . . . . . . . . . . . . . .188 ▫ To Resume . . . . . . . . . . . . . . . . . . . . . . . . . .188 ▫ To Vary The Speed Setting . . . . . . . . . . . . . . .189 ▫ Setting The Following Distance In ACC . . . . . .191 ▫ Overtake Aid . . . . . . . . . . . . . . . . . . . . . . . .195 ▫ ACC Operation At Stop . . . . . . . . . . . . . . . . .195 ▫ Adaptive Cruise Control (ACC) Menu . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 ▫ ParkSense Warning Display . . . . . . . . . . . . . .221 ▫ Cleaning The ParkSense System . . . . . . . . . . .243 ▫ ParkSense Display . . . . . . . . . . . . . . . . . . . . .222 ▫ ParkSense System Usage Precautions . . . . . . . .243 ▫ Enabling And Disabling ParkSense . . . . . . . . .226 䡵 PARKSENSE ACTIVE PARK ASSIST SYSTEM — ▫ Service The ParkSense Rear Park Assist IF EQUIPPED . . . . . . . . . . . . . . . . . . . . . . . . .245 System . . . . . . .
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Sunglass Bin Door . . . . . . . . . . . . . . . . . . . .273 ▫ Closing Sunroof — Express. . . . . . . . . . . . . . .286 䡵 GARAGE DOOR OPENER — IF EQUIPPED . . .274 ▫ Closing Sunroof — Manual Mode . . . . . . . . . .286 ▫ Before You Begin Programming HomeLink . . .276 ▫ Pinch Protect Feature . . . . . . . . . . . . . . . . . . .286 ▫ Programming A Rolling Code . . . . . . . . . . . . .277 ▫ Venting Sunroof — Express . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 ▫ Venting Sunroof — Express . . . . . . . . . . . . . .290 ▫ Rear Seat Cupholders . . . . . . . . . . . . . . . . . .298 ▫ Opening Power Shade — Express . . . . . . . . . .290 䡵 STORAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . .299 ▫ Opening Power Shade — Manual Mode . . . . .291 ▫ Glove Compartment . . . . . . . . . . . . . . . . . . .299 ▫ Closing Power Shade — Express . . . . . . . . . . .291 ▫ Console Features . . . . . . . . . . . . . .
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Day/Night Mirror — If Equipped The mirror head can be adjusted up, down, left, and right for various drivers. The mirror should be adjusted to center on the view through the rear window. Headlight glare from vehicles behind you can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle). The mirror should be adjusted while set in the day position (toward the windshield).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 Automatic Dimming Mirror — If Equipped The mirror head can be adjusted up, down, left, and right for various drivers. The mirror should be adjusted to center on the view through the rear window. 3 This mirror automatically adjusts for headlight glare from vehicles behind you. NOTE: The Automatic Dimming Mirror feature is disabled when the vehicle is in reverse gear to improve rear view viewing.
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! ALWAYS obey traffic laws and pay attention to the road. Some Uconnect Access services, including 9-1-1 and Assist, will NOT work without an operable 1X (voice/data) or 3G (data) network connection.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 3. Once a connection between the vehicle and a 9-1-1 operator is made, the 9-1-1 Call system may transmit 1. Push the 9-1-1 Call button on the Rearview Mirror. the following important vehicle information to a 9-1-1 NOTE: In case the 9-1-1 Call button is pushed in error, operator: there will be a 10 second delay before the 9-1-1 Call • Indication that the occupant placed a 9-1-1 Call. system initiates a call to a 9-1-1 operator.
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: • Your vehicle may be transmitting data as authorized by the subscriber. • Once a connection is made between the vehicle’s 9-1-1 Call system and the 9-1-1 operator, the 9-1-1 operator may be able to open a voice connection with the vehicle to determine if additional help is needed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 WARNING! (Continued) electrical equipment to the vehicle’s electrical system. This may prevent your vehicle from sending a signal to initiate an emergency call. To avoid interference that can cause the 9-1-1 Call system to fail, never add aftermarket equipment (e.g., two-way mobile radio, CB radio, data recorder, etc.) to your vehicle’s electrical system or modify the antennas on your vehicle.
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Ignoring the Rearview Mirror light could mean you will not have 9-1-1 Call services. If the Rearview Mirror light is illuminated, have an authorized dealer service the 9-1-1 Call system immediately. • The Occupant Restraint Control module turns on the air bag Warning Light on the instrument panel if a malfunction in any part of the system is detected.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 WARNING! ALWAYS obey traffic laws and pay attention to the road. Some Uconnect Access services, including 9-1-1 and Assist, will NOT work without an operable 1X (voice/data) or 3G (data) network connection. General Information This device complies with Part 15 of the FCC Rules.
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Outside Mirrors Outside Mirrors Folding Feature To receive maximum benefit, adjust the outside mirror(s) All outside mirrors are hinged and may be moved either to center on the adjacent lane of traffic and a slight forward or rearward to resist damage. The hinges have overlap of the view obtained from the inside mirror.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 The third LED supplies illuminated entry lighting, which turns on in both mirrors when you use the Remote Keyless Entry (RKE) transmitter or open any door. This LED shines downward to illuminate the ground adjacent to the Front and Rear Doors. the vehicle is shifted into REVERSE. Outside mirrors will then return to the original position when the vehicle is shifted out of REVERSE position.
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Using the mirror control switch, push on any of the four arrows for the direction that you want the mirror to move. Heated Mirrors — If Equipped These mirrors are heated to melt frost or ice. This feature can be activated whenever you turn on the rear window defroster (if equipped). Refer to “Rear Window Features” in “Understanding The Features Of Your Vehicle” for further information.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 Illuminated Vanity Mirrors — If Equipped Sun Visor “Slide-On Rod” Feature — If Equipped An illuminated vanity mirror is on each sun visor. To use This feature allows for additional flexibility in positionthe mirror, rotate the sun visor downward and swing the ing the visor to block out the sun. mirror cover upward. The light will turn on automati1. Fold down the sun visor. cally. Closing the mirror cover will turn off the light. 2.
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE BLIND SPOT MONITORING (BSM) — IF EQUIPPED The Blind Spot Monitoring (BSM) system uses two radarbased sensors, located inside the rear bumper fascia, to detect highway licensable vehicles (automobiles, trucks, motorcycles, etc.) that enter the blind spot zones from the rear/front/side of the vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 The BSM detection zone covers approximately one lane width on both sides of the vehicle (12 ft or 3.8 m). The zone length starts at the outside rear view mirror and extends approximately 10 ft (3 m) beyond the rear bumper of the vehicle. The BSM system monitors the detection zones on both sides of the vehicle when the vehicle speed reaches approximately 6 mph (10 km/h) or higher and will alert the driver of vehicles in these areas.
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Entering From The Side Entering From The Rear Vehicles that move into your adjacent lanes from either Vehicles that come up from behind your vehicle on either side of the vehicle. side and enter the rear detection zone with a relative speed of less than 30 mph (48 km/h).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 Overtaking Traffic If you pass another vehicle slowly (with a relative speed of less than 15 mph (24 km/h) and the vehicle remains in the blind spot for approximately 1.5 seconds, the warning light will be illuminated. If the difference in speed between the two vehicles is greater than 15 mph (24 km/h), the warning light will not illuminate.
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Overtaking/Passing The BSM system will not alert you of objects that are traveling in the opposite direction of the vehicle in adjacent lanes.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 WARNING! (Continued) system is not designed to detect pedestrians, bicyclists, or animals. Even if your vehicle is equipped with the BSM system, always check your vehicle’s mirrors, glance over your shoulder, and use your turn signal before changing lanes. Failure to do so can result in serious injury or death. Rear Cross Path Opposing Traffic WARNING! The Blind Spot Monitoring system is only an aid to help detect objects in the blind spot zones.
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: In a parking lot situation, oncoming vehicles can be obscured by vehicles parked on either side. If the sensors are blocked by other structures or vehicles, the system will not be able to alert the driver. When RCP is on and the vehicle is in REVERSE, the driver is alerted using both the visual and audible alarms, including reducing the radio volume.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 turn signal is then activated, and it corresponds to an alert present on that side of the vehicle, an audible chime Three selectable modes of operation are available in the will also be sounded. Whenever a turn signal and deUconnect System. Refer to “Uconnect Settings/Customer tected object are present on the same side at the same Programmable Features” in “Understanding Your Instrutime, both the visual and audible alerts will be issued.
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The BSM system will store the current operating SEATS mode when the vehicle is shut off. Each time the vehicle Seats are a part of the Occupant Restraint System of the is started the previously stored mode will be recalled and vehicle. used. General Information This vehicle has systems that operate on radio frequency that comply with Part 15 of the Federal Communications Commission (FCC) rules and with Industry Canada Standards RSS- GEN/210/220/310.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 Power Seats — If Equipped Adjusting The Seat Forward Or Rearward Some models may be equipped with a power driver’s seat. The power seat switch is located on the outboard side of the seat near the floor. Use the switch to move the seat up, down, forward or rearward. The seat can be adjusted both forward and rearward. Push the seat switch forward or rearward. The seat will move in the direction of the switch.
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Reclining The Seatback Forward Or Rearward The seatback can be reclined both forward and rearward. Push the seat recliner switch forward or rearward. The seatback will move in the direction of the switch. Release the switch when the desired position has been reached. Power Seat Recliner Switch WARNING! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 Power Lumbar — If Equipped Vehicles equipped with power driver’s seat may be equipped with power lumbar. The power lumbar switch is located on the outboard side of the power seat. Push the switch forward or rearward to increase or decrease the lumbar support. Push the switch upward or downward to raise or lower the lumbar support.
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE While sitting in the seat, lift up on the bar and move the seat forward or rearward. Release the bar once you have Manual Front Seat Forward/Rearward Adjustment reached the desired position. Then, using body pressure, On models equipped with manual seats, the adjusting move forward and rearward on the seat to be sure that bar is located at the front of the seats, near the floor. the seat adjusters have latched.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 Manual Front Seat Recline Adjustment To adjust the seatback, lift the lever located on the outboard side of the seat, lean back to the desired position and release the lever. To return the seatback, lift the lever, lean forward and release the lever. Recline Lever WARNING! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest.
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Manual Seat Height Adjustment — If Equipped Front Heated Seats — If Equipped The driver’s seat height can be raised or lowered by The front heated seats control buttons are located within using a lever, located on the outboard side of the seat. the Uconnect system. You can gain access to the control Pull upward on the lever to raise the seat height or push buttons through the climate screen or the controls screen.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 NOTE: The engine must be running for the heated seats to operate. Vehicles Equipped With Remote Start On models that are equipped with remote start, the heated seats can be programed to come on during a remote start. This feature can be programmed through the Uconnect system. Refer to “Uconnect Settings” in “Understanding Your Instrument Panel” for further information. WARNING! (Continued) even at low temperatures, especially if used for long periods of time.
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The front ventilated seats control buttons are located This feature can be programmed through the Uconnect within the Uconnect system. You can gain access to the system. Refer to “Uconnect Settings” in “Understanding control buttons through the climate screen or the controls Your Instrument Panel” for further information. screen. Head Restraints once to choose HI.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 NOTE: Do not reverse the head restraints (making the To raise the head restraint, pull upward on the head rear of the head restraint face forward) in an attempt to restraint. To lower the head restraint, push the adjustment button, located at the base of the head restraint, and gain additional clearance to the back of your head. push downward on the head restraint.
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Front Head Restraint 1 — Release Button 2 — Adjustment Button • A loose head restraint thrown forward in a collision or hard stop could cause serious injury or death to occupants of the vehicle. Always securely stow removed head restraints in a location outside the occupant compartment. • ALL the head restraints MUST be reinstalled in the vehicle to properly protect the occupants.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 Rear Head Restraints The rear outboard head restraints have three positions Up, Mid and Down. The center head restraint has only two positions, Up and Down. When the center seat is being occupied the head restraint should be in the raised position. When there is no occupant in the center seat, the head restraint can be lowered for maximum visibility for the driver. To raise the head restraint, pull upward on the head restraint.
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! ALL the head restraints MUST be reinstalled in the vehicle to properly protect the occupants. Follow the re-installation instructions above prior to operating the vehicle or occupying a seat. Folding Rear Seat To provide additional storage area, the rear seatback can be folded forward. Pull on the loops to fold down either or both seatbacks.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 WARNING! • Be certain that the seatback is securely locked into position. If the seatback is not securely locked into position the seat will not provide the proper stability for child seats and/or passengers. An improperly latched seat could cause serious injury. • The rear cargo area of the vehicle (with the rear seatbacks in the locked-up or folded down position) should not be used as a play area by children. They could be seriously injured in a collision.
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Adjust all memory profile settings to desired preferences (i.e., seat, side mirror and radio station presets). 3. Push and release the SET button on the memory switch, then push the number (1) button within five seconds. The Electronic Vehicle Information Center (EVIC) or Driver Information Display (DID), will display which memory position is being set. If desired, a second memory profile can be stored into memory as follows: 1.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 NOTE: Before programming your RKE transmitters you must select the “Memory To FOB” feature through the • Memory profiles can be set without the vehicle in Uconnect system screen. Refer to “Uconnect Settings” in PARK, but the vehicle must be in PARK to recall a “Understanding Your Instrument Panel” for further inmemory profile. formation.
156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Push and release the LOCK button on the RKE trans- A recall can be cancelled by pushing any of the MEMORY buttons (S, 1, or 2) during a recall. When a recall is mitter within 10 seconds. cancelled, the driver seat will stop moving. A delay of NOTE: Your RKE transmitters can be unlinked to your one second will occur before another recall can be memory settings by pushing the SET (S) button, followed selected.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 The seat will return to its previously set position when TO OPEN AND CLOSE THE HOOD you cycle the vehicle’s ignition to the ACC or RUN To open the hood, two levers must be released. position. 1. Pull the release lever located below the instrument • The Easy Entry/Easy Exit feature is disabled when the panel and in front of the driver’s door. driver seat position is less than 0.9 in (22.7 mm) forward of the rear stop.
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Safety Latch Lever Location Safety Latch Lever 3. Reach under the center front edge of the hood and 4. Lift the hood upward to the open position. push and hold the safety latch lever to the right. CAUTION! To prevent possible damage, do not slam the hood to close it. Use a firm downward push at the front center of the hood to ensure that both latches engage.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 WARNING! Be sure the hood is fully latched before driving your vehicle. If the hood is not fully latched, it could open when the vehicle is in motion and block your vision. Failure to follow this warning could result in serious injury or death. 3 LIGHTS Headlight Switch The headlight switch is located on the left side of the instrument panel.
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE is set to ON. In addition, the headlights will turn off when the wipers are turned off if they were turned on by This system automatically turns the headlights on or off this feature. according to ambient light levels. To turn the system on, rotate the headlight switch clockwise to the last detent for NOTE: The Headlights On with Wipers feature can be automatic headlight operation. When the system is on, turned on or off using the Uconnect System.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 If you turn the headlights or parking lights on, or place Automatic High Beam Headlamp Control — If the ignition in ACC or RUN, the system will cancel the Equipped delay. The Automatic High Beam Headlamp Control system If you turn the headlights off before the ignition, they will provides increased forward lighting at night by automating high beam control through the use of a digital camera turn off in the normal manner. mounted on the inside rearview mirror.
162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE and other obstructions on the windshield or camera NOTE: This system will not activate until the vehicle is at or above 15 mph (24 km/h). lens will cause the system to function improperly. • To opt out of the Advanced Auto High-Beam Sensitiv- To Deactivate ity Control (default) and enter Reduced High-Beam 1.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 NOTE: If allowed by law in the country in which the vehicle was purchased the Daytime Running Lights can be turned on and off using the Uconnect System, refer to “Uconnect Settings” in “Understanding Your Instrument Panel” for further information. 3 Lights-On Reminder If the headlights or parking lights are on after the ignition is placed in the OFF position, a chime will sound to alert the driver when the driver’s door is opened.
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE An indicator light in the instrument cluster illuminates when the fog lights are turned on. NOTE: The fog lights will operate with the low beam headlights or parking lights on. However, selecting the high beam headlights will turn off the fog lights. Multifunction Lever The multifunction lever controls the operation of the turn signals, headlight beam selection and passing lights. The multifunction lever is located on the left side of the steering column.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 Turn Signals signal is flashing. The Daytime Running Lamp will turn back on when the turn signal is turned off. Move the multifunction lever up or down and the arrows on each side of the instrument cluster flash to show Lane Change Assist proper operation of the front and rear turn signal lights. Tap the lever up or down once, without moving beyond the detent, and the turn signal (right or left) will flash NOTE: three times then automatically turn off.
166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Front Map/Reading Lights The front map/reading lights are mounted in the overhead console. Front Map/Reading Lights — With Center Buttons There are two map/reading light buttons located in the center of the overhead console that allow the lights to operate independently. Push the button once to turn the light on. To turn the light off, push the button a second time.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 NOTE: The lights also turn on when a door is opened. The two map/reading lights can be operated indepen- The lights will also turn on when the UNLOCK button on the RKE is pushed. dently by pushing the lenses. Interior Lights Push the lens once to turn the light on. Front Map/Reading Lights — With Push Lenses To turn the light off, push the lens a second time. The interior lights come on when a door is opened.
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE With the parking lights or headlights on, rotating the Ambient Light Control — If Equipped instrument panel dimmer control upward will increase Rotate the ambient dimmer control upward or downthe brightness of the instrument panel lights. ward to increase or decrease the brightness of the ambient light located in the overhead console, door handle lights, under I/P lights, door map pocket lights, and cubby bin lights.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 Dome Light Position Parade Mode (Daytime Brightness Feature) Rotate the instrument panel dimmer control completely upward to the second detent to turn on the interior lights. The interior lights will remain on when the instrument panel dimmer control is in this position. Rotate the instrument panel dimmer control upward to the first detent.
170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WINDSHIELD WIPERS AND WASHERS Windshield Wiper Operation The windshield wiper/washer controls are located on the windshield wiper/washer lever on the right side of the steering column. The front wipers are operated by rotating a switch, located on the end of the lever. Rotate the end of the lever to one of the first four detent positions for intermittent settings, the fifth detent for low wiper operation and the sixth detent for high wiper operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 NOTE: If snow packing occurs that obstructs the normal operation of the windshield wipers the following message will appear in the Electronic Vehicle Information Center (EVIC) or the Driver Information Display (DID): ⬙Front Wipers Blocked Cycle Switch or Clean the Windshield⬙. It is important to remove the snow accumulation to allow the wipers to function normally and to maintain good visibility of the road.
172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Windshield Washer Operation To use the washer, pull the lever rearward toward you and hold while spray is desired. If the lever is pulled while in the intermittent setting, the wipers will turn on and operate for several wipe cycles after the lever is released, and then resume the intermittent interval previously selected. Intermittent Wiper Operation NOTE: If the vehicle is moving less than 10 mph (16 km/h), delay times will be doubled.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173 If the lever is pulled while the wipers are in the off NOTE: The mist feature does not activate the washer position, the wipers will operate for several wipe cycles, pump; therefore, no washer fluid will be sprayed on the windshield. The wash function must be used in order to then turn off. spray the windshield with washer fluid. WARNING! 3 Sudden loss of visibility through the windshield could lead to a collision.
174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The Rain Sensing feature may not function properly when ice, or dried salt water is present on the windThis feature senses moisture on the windshield and shield. automatically activates the wipers for the driver. The feature is especially useful for road splash or overspray • Use of Rain-X or products containing wax or silicone from the windshield washers of the vehicle ahead. Rotate may reduce Rain Sensing performance.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175 • Transmission In NEUTRAL Position — When the ignition is ON, and the automatic transmission is in the NEUTRAL position, the Rain Sensing system will not operate until the wiper switch is moved, vehicle speed is greater than 3 mph (5 km/h), or the shift lever/gear selector is moved out of the NEUTRAL position. TILT/TELESCOPING STEERING COLUMN This feature allows you to tilt the steering column upward or downward.
176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To unlock the steering column, pull the control handle down. To tilt the steering column, move the steering wheel upward or downward as desired. To lengthen or shorten the steering column, pull the steering wheel outward or push it inward as desired. To lock the steering column in position, push the control handle up until fully engaged. WARNING! Do not adjust the steering column while driving.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177 Vehicles Equipped With Remote Start WARNING! (Continued) On models that are equipped with remote start, the heated steering wheel can be programmed to come on during a remote start through the Uconnect system. Refer to “Uconnect Settings” in “Understanding Your Instrument Panel” for further information. • Do not place anything on the steering wheel that insulates against heat, such as a blanket or steering wheel covers of any type and material.
178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: In order to ensure proper operation, the Electronic Speed Control System has been designed to shut down if multiple Speed Control functions are operated at the same time. If this occurs, the Electronic Speed Control System can be reactivated by pushing the Electronic Speed Control ON/OFF button and resetting the desired vehicle set speed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179 WARNING! Leaving the Electronic Speed Control system on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the system OFF when you are not using it. To Set A Desired Speed Turn the Electronic Speed Control ON.
180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The drivers preferred units can be selected through the • If the button is continually pushed, the set speed will instrument panel settings if equipped. Refer to “Undercontinue to increase until the button is released, then the new set speed will be established. standing Your Instrument Panel” for more information. The speed increment shown is dependant on the chosen To Decrease Speed speed unit of U.S.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181 • If the button is continually pushed, the set speed will NOTE: The Electronic Speed Control system maintains continue to decrease until the button is released, then speed up and down hills. A slight speed change on moderate hills is normal. the new set speed will be established. On steep hills, a greater speed loss or gain may occur so it may be preferable to drive without Electronic Speed • Pushing the SET - button once will result in a 1 km/h Control.
182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • If the ACC sensor detects a vehicle ahead, ACC will apply limited braking or acceleration (not to exceed the original set speed) automatically to maintain a Adaptive Cruise Control (ACC) increases the driving preset following distance, while matching the speed of convenience provided by cruise control while traveling the vehicle ahead. on highways and major roadways. However, it is not a safety system and not designed to prevent collisions.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 183 You can change the mode by using the Cruise Control buttons. The two control modes function differently. Always confirm which mode is selected. WARNING! (Continued) • Adaptive Cruise Control (ACC) is a convenience system. It is not a substitute for active driving involvement.
184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! (Continued) You should switch off the ACC system: • When driving in fog, heavy rain, heavy snow, sleet, heavy traffic, and complex driving situations (i.e., in highway construction zones). • When entering a turn lane or highway off ramp; when driving on roads that are winding, icy, snowcovered, slippery, or have steep uphill or downhill slopes. • When towing a trailer up or down steep slopes.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 185 NOTE: Any chassis/suspension or tire size modifications NOTE: You cannot engage ACC under the following to the vehicle will effect the performance of the Adaptive conditions: Cruise Control and Forward Collision Warning System. • When you apply the brakes. Activating Adaptive Cruise Control (ACC) • When the parking brake is set. You can only engage ACC if the vehicle speed is above • When the automatic transmission is in PARK, RE0 mph (0 km/h).
186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To turn the system OFF, push and release the Adaptive Push and release the Adaptive Cruise Control (ACC) Cruise Control (ACC) ON/OFF button again. At this ON/OFF button. The ACC menu in the EVIC/DID time, the system will turn off and the EVIC/DID will display “Adaptive Cruise Control (ACC) Off.” displays “ACC Ready.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 187 WARNING! Leaving the Adaptive Cruise Control (ACC) system on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have a collision. Always leave the system off when you are not using it. NOTE: ACC cannot be set if there is a stationary vehicle in front of your vehicle in close proximity. Remove your foot from the accelerator pedal.
188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The shift lever/gear selector is removed from the To Resume Drive position. If there is a set speed in memory push the RES (resume) • The Electronic Stability Control/Traction Control Sys- button and then remove your foot from the accelerator pedal. The EVIC/DID will display the last set speed. tem (ESC/TCS) activates. • The vehicle parking brake is applied. NOTE: • Driver seatbelt is unbuckled at low speeds.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 189 WARNING! (Continued) that is too high or too low for prevailing traffic and road conditions could cause the vehicle to accelerate or decelerate too sharply for safe operation. Failure to follow these warnings can result in a collision and death or serious personal injury. To Vary The Speed Setting To Increase Speed While ACC is set, you can increase the set speed by pushing the SET + button.
190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • If the button is continually pushed, the set speed will • If the button is continually pushed, the set speed will continue to increase in 10 km/h increments until the continue to decrease in 5 mph decrements until the button is released. The decrease in set speed is rebutton is released. The increase in set speed is reflected flected in the EVIC/DID. in the EVIC/DID.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 191 • When you use the SET - button to decelerate, if the engine’s braking power does not slow the vehicle sufficiently to reach the set speed, the brake system will automatically slow the vehicle. Setting The Following Distance In ACC The specified following distance for ACC can be set by varying the distance setting between four bars (longest), three bars (long), two bars (medium) and one bar (short).
192 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Distance Setting 4 Bars (Longest) Distance Setting 3 Bars (Long)
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 193 3 Distance Setting 2 Bars (Medium) Distance Setting 1 Bar (Short) To increase the distance setting, push the Distance Setting — Increase button and release. Each time the button is pushed, the distance setting increases by one bar (longer).
194 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To decrease the distance setting, push the Distance Set- • The system disengages. (Refer to the information on ting — Decrease button and release. Each time the button ACC Activation). is pushed, the distance setting decreases by one bar The maximum braking applied by ACC is limited; how(shorter). ever, the driver can always apply the brakes manually, if If there is no vehicle ahead, the vehicle will maintain the necessary. set speed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 195 Overtake Aid When driving with ACC engaged and following a vehicle, the system will provide an additional acceleration up to the ACC set speed to assist in passing the vehicle. This additional acceleration is triggered when the driver utilizes the left turn signal and will only be active when passing on the left hand side.
196 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: After the ACC system holds your vehicle at a standstill for approximately 3 consecutive minutes, the parking brake will be activated, and the ACC system will be cancelled. Adaptive Cruise Control (ACC) Menu The EVIC/DID displays the current ACC system settings. The EVIC/DID is located in the center of the instrument cluster. The information it displays depends While ACC is holding your vehicle at a standstill, if the on ACC system status.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 197 Push the SET + or the SET- button (located on the steering Display Warnings And Maintenance wheel) and the following will display in the EVIC/DID: “Wipe Front Radar Sensor In Front Of Vehicle” ACC SET Warning When ACC is set, the set speed will display in the The “ACC/FCW Unavailable Wipe Front Radar Sensor” warning will display and also a chime will indicate when instrument cluster. conditions temporarily limit system performance.
198 UNDERSTANDING THE FEATURES OF YOUR VEHICLE vehicle has left these areas. Under rare conditions, when • Do not remove any screws from the sensor. Doing so the radar is not tracking any vehicles or objects in its path could cause an ACC system malfunction or failure and require a sensor realignment. this warning may temporarily occur.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 199 • Installing a snow plow, front-end protector, an aftermarket grille or modifying the grille is not recommended. Doing so may block the sensor and inhibit ACC/FCW operation. system will recover after the vehicle has left these areas. Under rare conditions, when the camera is not tracking any vehicles or objects in its path this warning may temporarily occur.
200 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Service ACC/FCW Warning Precautions While Driving With ACC If the system turns off, and the EVIC/DID displays “ACC/FCW Unavailable Service Required” or “Cruise/ FCW Unavailable Service Required”, there may be an internal system fault or a temporary malfunction that limits ACC functionality. Although the vehicle is still drivable under normal conditions, ACC will be temporarily unavailable.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 201 the vehicle is out of the curve the system will resume your original Set Speed. This is a part of normal ACC system functionality. NOTE: On tight turns ACC performance may be limited. Offset Driving Condition Example Turns And Bends When driving on a curve with ACC engaged, the system may decrease the vehicle speed and acceleration for stability reasons, with no target vehicle detected.
202 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Using ACC On Hills Lane Changing When driving on hills, ACC may not detect a vehicle in your lane. Depending on the speed, vehicle load, traffic conditions, and the steepness of the hills, ACC performance may be limited. ACC may not detect a vehicle until it is completely in the lane in which you are traveling.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 203 Narrow Vehicles Some narrow vehicles traveling near the outer edges of the lane or edging into the lane are not detected until they have moved fully into the lane. There may not be sufficient distance to the vehicle ahead.
204 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Stationary Objects And Vehicles General Information ACC does not react to stationary objects and stationary vehicles. For example, ACC will not react in situations where the vehicle you are following exits your lane and the vehicle ahead is stopped in your lane. Always be attentive and ready to apply the brakes if necessary.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 205 Normal (Fixed Speed) Electronic Speed Control Mode In addition to Adaptive Cruise Control mode, a Normal (Fixed Speed) Electronic Speed Control mode is available for cruising at fixed speeds. The Normal (Fixed Speed) Electronic Speed Control mode is designed to maintain a set cruising speed without requiring the driver to operate the accelerator. Electronic Speed Control can only be operated if the vehicle speed is above 20 mph (32 km/h).
206 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Once a speed has been set a message (CRUISE CON- The speed increment shown is dependant on the speed of TROL SET TO MPH/KM) will appear indicating what U.S. (mph) or Metric (km/h) units: speed was set. This light will turn on when the electronic U.S. Speed (mph) speed control is SET. • Pushing the SET + button once will result in a 1 mph To Vary The Speed Setting increase in set speed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 207 • If the button is continually pushed, the set speed will • If the button is continually pushed, the set speed will continue to increase in 10 km/h increments until the continue to decrease in 5 mph decrements until the button is released. The decrease in set speed is rebutton is released. The increase in set speed is reflected flected in the EVIC/DID display. in the EVIC/DID display.
208 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Cancel To Resume Speed The following conditions will cancel the Normal (Fixed To resume a previously set speed, push the RES button Speed) Electronic Speed Control without clearing the and release. Resume can be used at any speed above memory: 20 mph (32 km/h). • The brake pedal is applied. To Turn Off • The CANCEL button is pushed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 209 FORWARD COLLISION WARNING (FCW) WITH MITIGATION — IF EQUIPPED Forward Collision Warning (FCW) With Mitigation Operation If the driver does not take action based upon these progressive warnings, then the system will provide a limited level of active braking to help slow the vehicle and mitigate the potential forward collision.
210 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: • The minimum speed for FCW activation is 1 mph (2 km/h). • The FCW alerts may be triggered on objects other than vehicles such as guard rails or sign posts based on the course prediction. This is expected and is a part of normal FCW activation and functionality. FCW Message • It is unsafe to test the FCW system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 211 WARNING! Forward Collision Warning (FCW) is not intended to avoid a collision on its own, nor can FCW detect every type of potential collision. The driver has the responsibility to avoid a collision by controlling the vehicle via braking and steering. Failure to follow this warning could lead to serious injury or death.
212 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To turn the FCW system back ON, push the forward Changing FCW And Active Braking Status collision button again to turn the system ON (LED turns The FCW Sensitivity And Active Braking Settings are off). programmable through the Uconnect System. Refer to • Changing the FCW status to “Off” prevents the system “Uconnect Settings” in “Understanding Your Instrument from warning you of a possible collision with the Panel” for further information.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 213 drivable under normal conditions, the active braking may not be fully available. Once the condition that • The system will retain the last setting selected by the limited the system performance is no longer present, the driver after ignition shut down. system will return to its full performance state. If the • FCW may not react to irrelevant objects such as problem persists, see your authorized dealer.
214 UNDERSTANDING THE FEATURES OF YOUR VEHICLE LANESENSE — IF EQUIPPED LaneSense Operation The driver may manually override the haptic warning by applying torque into the steering wheel at any time. When only a single lane marking is detected and the driver unintentionally drifts across the lane marking (no turn signal applied), the LaneSense system provides a visual warning through the EVIC/DID to prompt the driver to remain within the lane.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 215 Turning LaneSense ON Or OFF The default status of LaneSense is “OFF”. The LaneSense button is located on the switch panel below the Uconnect display. To turn the LaneSense system ON, push the LaneSense button (LED turns off). A “Lane Sense On” message is shown in the Driver Information Display (DID). 3 Lane Sense On Message LaneSense Warning Button To turn the LaneSense system OFF, push the LaneSense button once to turn the system OFF (LED turns on).
216 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The LaneSense system will retain the last system state ON or OFF from the last ignition cycle when the ignition is changed to the ON/RUN position. LaneSense Warning Message The LaneSense system will indicate the current lane drift condition through the Driver Information Display (DID). 7.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 217 • When the LaneSense system senses the lane has been approached and is in a lane departure situation, the left thick lane line flashes yellow (on/off), the left thin line remains solid yellow and the LaneSense indicator changes from solid white to flashing yellow.
218 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • For example: If approaching the left side of the lane the steering wheel will turn to the right. Lanes Sensed (White Lines/Green Indicator) • When the LaneSense system senses a lane drift situation, the left thick lane line and left thin line turn solid Lane Sensed (Solid Yellow Thick Line, Solid Yellow Thin Line/Solid Yellow Indicator) yellow. The LaneSense indicator changes from solid green to solid yellow.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 219 thin line remains solid yellow. The LaneSense indicator changes from solid yellow to flashing yellow. At this time torque is applied to the steering wheel in the opposite direction of the lane boundary. 3 • For example: If approaching the left side of the lane the steering wheel will turn to the right.
220 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Changing LaneSense Status • Use of the turn signal suppresses the warnings. The LaneSense system settings can be configured • The system will not apply torque to the steering wheel through the Uconnect system screen. whenever a safety system engages. (anti-lock brakes, traction control system, electronic stability control, Follow these steps to change the LaneSense settings: forward collision warning, etc.) 1.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 221 ParkSense can be active only when the shift lever/gear selector is in REVERSE. If ParkSense is enabled at this shift lever/gear selector position, the system will remain active until the vehicle speed is increased to approximately 7 mph (11 km/h) or above.
222 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ParkSense Display When the vehicle is in REVERSE, the EVIC/DID will display the park assist ready system status. The system will indicate a detected obstacle by showing a single arc in one or more regions based on the obstacle’s distance and location relative to the vehicle. If an obstacle is detected in the center rear region, the display will show a single solid arc in the center rear region and will produce a one-half second tone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 223 3 Slow Tone/Solid Arc Slow Tone/Solid Arc
224 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Fast Tone/Flashing Arc Continuous Tone/Flashing Arc The vehicle is close to the obstacle when the warning display shows one flashing arc and sounds a continuous tone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 225 Rear Distance (in/cm) Arcs — Left Arcs — Center Arcs — Right Audible Alert Chime Radio Volume Reduced WARNING ALERTS 59-47 in 47-39 in (150-120 (120-100 cm) cm) Greater than 79 in (200 cm) None 79-59 in (200-150 cm) None None None None None 6th Solid 5th Solid 4th Solid None None None None 3rd Flashing None None Single 1/2Second Tone (for rear center only) Yes Slow (for rear center only) Yes Slow (for rear center only) Yes Fast (for rear c
226 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: ParkSense will reduce the volume of the radio, if When the ParkSense switch is pushed to disable the system, the instrument cluster will display the on, when the system is sounding an audio tone. “PARKSENSE OFF” message for approximately five secEnabling And Disabling ParkSense onds.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 227 sure the outer surface and the underside of the rear fascia/bumper is clean and clear of snow, ice, mud, dirt During vehicle start up, when the ParkSense Rear Park or other obstruction and then cycle the ignition. If the Assist System has detected a faulted condition, the message continues to appear, see an authorized dealer.
228 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Jackhammers, large trucks, and other vibrations could • Clean the ParkSense sensors regularly, taking care not affect the performance of ParkSense. to scratch or damage them. The sensors must not be covered with ice, snow, slush, mud, dirt or debris. • When you turn ParkSense OFF, the instrument cluster Failure to do so can result in the system not working will display “PARKSENSE OFF” Furthermore, once properly.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 229 CAUTION! WARNING! (Continued) • ParkSense is only a parking aid and it is unable to recognize every obstacle, including small obstacles. Parking curbs might be temporarily detected or not detected at all. Obstacles located above or below the sensors will not be detected when they are in close proximity. • The vehicle must be driven slowly when using ParkSense in order to be able to stop in time when an obstacle is detected.
230 UNDERSTANDING THE FEATURES OF YOUR VEHICLE and released when performing a reverse parking maneu- • The automatic braking function may not be applied ver if the system detects a possible collision with an fast enough for obstacles that move toward the rear of obstacle. the vehicle from the left and/or right sides. • The automatic braking function can be enabled/ disabled from the Customer-Programmable Features • The driver can override the automatic braking funcsection of the Uconnect System.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 231 • The system is provided to assist the driver and not to The system will become active again if the vehicle speed substitute the driver. is decreased to speeds less than approximately 6 mph (9 km/h). • The driver must stay in full control of the vehicle’s acceleration and braking and is responsible for the ParkSense Sensors vehicle’s movements.
232 UNDERSTANDING THE FEATURES OF YOUR VEHICLE obstacles from approximately 12 in (30 cm) up to 47 in ParkSense Display (120 cm) from the front fascia/bumper in the horizontal Rear Park Assist direction, depending on the location, type and orientaWhen the vehicle is in REVERSE, the EVIC/DID will tion of the obstacle. display the park assist ready system status.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 233 the display will show the single arc moving closer to the vehicle and the tone will change from fast to continuous.
234 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Slow Tone/Solid Arc Fast Tone/Flashing Arc
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 235 3 Fast Tone/Flashing Arc Continuous Tone/Flashing Arc The vehicle is close to the obstacle when the warning display shows one flashing arc and sounds a continuous tone.
236 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Distance (in/cm) Arcs — Left Arcs — Center Arcs — Right Audible Alert Chime WARNING ALERTS 59-47 in 47-39 in (150-120 (120-100 cm) cm) Greater than 79 in (200 cm) None 79-59 in (200-150 cm) 39-25 in (100-65 cm) 25-12 in (65-30 cm) Less than 12 in (30 cm) None None None None 1st Flashing 5th Solid 4th Solid None None None 3rd Flashing None Single 1/2Second Tone (for rear center only) Slow (for rear center only) Slow (for rear center onl
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 237 Rear Distance (in/cm) Radio Volume Reduced Greater than 79 in (200 cm) No 79-59 in (200-150 cm) Yes WARNING ALERTS 59-47 in 47-39 in (150-120 (120-100 cm) cm) Yes Yes 39-25 in (100-65 cm) Yes 25-12 in (65-30 cm) Yes Less than 12 in (30 cm) Yes NOTE: ParkSense will reduce the volume of the radio, if If an obstacle is detected in the center front region, the display will show a single arc in the center front region.
238 UNDERSTANDING THE FEATURES OF YOUR VEHICLE sound tone. As the vehicle moves closer to the obstacle, the display will show the single arc moving closer to the vehicle and the tone will change from fast to continuous.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 239 3 Fast Tone/Flashing Arc Continuous Tone/Flashing Arc The vehicle is close to the obstacle when the warning display shows one flashing arc and sounds a continuous tone.
240 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Front Distance (in/cm) Arcs — Left Arcs — Center Arcs — Right Audible Alert Chime Radio Volume Reduced Greater than 47 in (120 cm) None None None None No WARNING ALERTS 47-39 in 39-25 in (120-100 cm) (100-65 cm) None None 4th Solid 3rd Flashing None None None None No No 25-12 in (65-30 cm) 2nd Flashing 2nd Flashing 2nd Flashing Fast Less than 12 in (30 cm) 1st Flashing 1st Flashing 1st Flashing Continuous Yes Yes NOTE: ParkSense will reduce the volume
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 241 If the Uconnect System is equipped, chime volume settings will not be accessible from the EVIC/DID. The chime volume settings include LOW, MEDIUM, and HIGH. The factory default volume setting is MEDIUM. 3 ParkSense will retain its last known configuration state through ignition cycles. Enabling And Disabling ParkSense ParkSense can be enabled and disabled with the ParkSense switch, located on the switch panel below the Uconnect display.
242 UNDERSTANDING THE FEATURES OF YOUR VEHICLE REVERSE and the system is disabled, the EVIC/DID will and the system has detected a faulted condition, the display the “PARKSENSE OFF” message for as long as Electronic Vehicle Information Center (EVIC) or Driver Information Display (DID) will display a ⬙PARKSENSE the vehicle is in REVERSE. UNAVAILABLE WIPE REAR SENSORS⬙, ⬙PARKSENSE The ParkSense switch LED will be ON when ParkSense is UNAVAILABLE WIPE FRONT SENSORS⬙ or disabled or requires service.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 243 vehicle is in REVERSE. Refer to “Electronic Vehicle Cleaning The ParkSense System Information Center (EVIC) or ⬙ Driver Information Dis- Clean the ParkSense sensors with water, car wash soap play (DID)” for further information. and a soft cloth. Do not use rough or hard cloths. Do not If ⬙PARKSENSE UNAVAILABLE WIPE REAR SENSORS⬙ scratch or poke the sensors. Otherwise, you could damor ⬙PARKSENSE UNAVAILABLE WIPE FRONT SEN- age the sensors.
244 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • When you move the shift lever to the REVERSE position and ParkSense is turned off, the instrument cluster will display “PARKSENSE OFF” for as long as the vehicle is in REVERSE. misinterpreting a close object as a sensor problem, causing the “PARKSENSE UNAVAILABLE SERVICE REQUIRED” message to be displayed in the instrument cluster.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 245 CAUTION! (Continued) • The vehicle must be driven slowly when using ParkSense in order to be able to stop in time when an obstacle is detected. It is recommended that the driver looks over his/her shoulder when using ParkSense. WARNING! Drivers must be careful when backing up even when using ParkSense.
246 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The system is provided to assist the driver and not to Enabling And Disabling The ParkSense Active substitute the driver. Park Assist System • During a semi-automatic maneuver, if the driver touches the steering wheel after being instructed to remove their hands from the steering wheel, the system will cancel, and the driver will be required to manually complete the parking maneuver.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 247 To enable the ParkSense Active Park Assist system, push the • ParkSense Active Park Assist switch once (LED turns on). • To disable the ParkSense Active Park Assist system, push the ParkSense Active Park Assist switch again (LED turns • off). The ParkSense Active Park Assist system will turn off • automatically for any of the following conditions: • The parking maneuver is completed. The Driver’s door is opened. The trunk is opened.
248 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The Driver’s door is closed. • The trunk is closed. • Vehicle speed is less than 15 mph (25 km/h). Parallel Parking Space Assistance Operation/ Display When the ParkSense Active Park Assist system is enabled the “Active ParkSense Searching - Press OK for Perpendicular Park” message will appear in the Driver Information Display (DID). You may switch to perpendicular parking if you desire.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 249 • The driver needs to make sure that the selected parking space for the maneuver remains free and clear of any obstructions (e.g. pedestrians, bicycles, etc.). • The driver is responsible to ensure that the selected parking space is suitable for the maneuver and free/ clear of anything that may be overhanging or protruding into the parking space (e.g., ladders, tailgates, etc. from surrounding objects/vehicles).
250 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Parking Space Found — Keep Moving Forward Parking Space Found — Stop And Remove Hands From Wheel Once the vehicle is in position, you will be instructed to stop the vehicle’s movement and remove your hands Once the vehicle is at a standstill with your hands removed from the steering wheel, you will be instructed from the steering wheel. to place the shift lever into the REVERSE position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 251 3 Parking Space Found — Shift To Reverse Check Surroundings — Wait For Steering To Complete When the driver places the shift lever into the REVERSE The system will then instruct the driver to check their position, the system may instruct the driver to wait for surroundings and move backward. steering to complete.
252 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • When the system instructs the driver to remove their hands from the steering wheel, the driver should check their surroundings and begin to back up slowly. • The ParkSense Active Park Assist system will allow a maximum of six shifts between DRIVE or REVERSE. If the maneuver cannot be completed within six shifts, the system will cancel and the DID will instruct the driver to complete the maneuver manually.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 253 When the vehicle has reached the end of its backward NOTE: It is the drivers responsibility to use the brake movement, the system will instruct the driver to check and stop the vehicle. The driver should check their their surroundings and stop the vehicle’s movement. surroundings and be prepared to stop the vehicle either when instructed to, or when driver intervention is required.
254 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Check Surroundings — Shift To Drive Check Surroundings — Wait For Steering To Complete When the driver places the shift lever into the DRIVE The system will then instruct the driver to check their position, the system may instruct the driver to wait for surroundings and move forward. steering to complete.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 255 3 Check Surroundings — Move Forward Check Surroundings — STOP When the vehicle has reached the end of its forward NOTE: It is the drivers responsibility to use the brake movement, the system will instruct the driver to check and stop the vehicle. The driver should check their their surroundings and stop the vehicle’s movement. surroundings and be prepared to stop the vehicle either when instructed to, or when driver intervention is required.
256 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Once the vehicle is in a standstill condition, the driver will be instructed to place the shift lever into the REVERSE position. Check Surroundings — Wait For Steering To Complete The system will then instruct the driver to check their surroundings and move backward. Check Surroundings — Shift To Reverse When the driver places the shift lever into the REVERSE position, the system may instruct the driver to wait for steering to complete.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 257 3 Check Surroundings — Move Backward Your vehicle is now in the parallel park position. When the maneuver is complete, the driver will be instructed to check the vehicle’s parking position. If the driver is satisfied with the vehicle position, they should shift to PARK. The ⬙Active ParkSense Complete - Check Parking Position⬙ message will be momentarily displayed.
258 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Perpendicular Parking Space Assistance Operation/Display When the ParkSense Active Park Assist system is enabled, the “Active ParkSense Searching - Press OK for Perpendicular Park” message will show in the DID display. Push the OK button on the left side steering wheel switch to change your parking space setting to a perpendicular maneuver. You may switch back to parallel parking if you desire.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 259 • When seeking for a parking space, the driver should drive as parallel or perpendicular (depending on the • When searching for a parking space, use the turn type of maneuver) to other vehicles as possible. signal indicator to select which side of the vehicle you want to perform the parking maneuver.
260 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Parking Space Found — Keep Moving Forward Parking Space Found — Stop And Remove Hands From Wheel Once the vehicle is in position, you will be instructed to stop the vehicle’s movement and remove your hands Once the vehicle is at a standstill with your hands removed from the steering wheel, you will be instructed from the steering wheel. to place the shift lever into the REVERSE position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 261 3 Parking Space Found — Shift To Reverse Check Surroundings — Wait For Steering To Complete When the driver places the shift lever into the REVERSE The system will then instruct the driver to check their position, the system may instruct the driver to wait for surroundings and move backward. steering to complete.
262 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • When the system instructs the driver to remove their hands from the steering wheel, the driver should check their surroundings and begin to back up slowly. • The ParkSense Active Park Assist system will allow a maximum of six shifts between DRIVE or REVERSE. If the maneuver cannot be completed within six shifts, the system will cancel and the DID will instruct the driver to complete the maneuver manually.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 263 When the vehicle has reached the end of its backward NOTE: It is the drivers responsibility to use the brake movement, the system will instruct the driver to check and stop the vehicle. The driver should check their their surroundings and stop the vehicle’s movement. surroundings and be prepared to stop the vehicle either when instructed to, or when driver intervention is required.
264 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Check Surroundings — Shift To Drive Check Surroundings — Wait For Steering To Complete When the driver places the shift lever into the DRIVE The system will then instruct the driver to check their position, the system may instruct the driver to wait for surroundings and move forward. steering to complete.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 265 3 Check Surroundings — Move Forward Check Surroundings — STOP When the vehicle has reached the end of its forward NOTE: It is the drivers responsibility to use the brake movement, the system will instruct the driver to check and stop the vehicle. The driver should check their their surroundings and stop the vehicle’s movement. surroundings and be prepared to stop the vehicle either when instructed to, or when driver intervention is required.
266 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Once the vehicle is in a standstill condition, the driver will be instructed to place the shift lever into the REVERSE position. Check Surroundings — Wait For Steering To Complete The system will then instruct the driver to check their surroundings and move backward. Check Surroundings — Shift To Reverse When the driver places the shift lever into the REVERSE position, the system may instruct the driver to wait for steering to complete.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 267 3 Check Surroundings — Move Backwards Your vehicle is now in the perpendicular park position. When the maneuver is complete, the driver will be instructed to check the vehicle’s parking position. If the driver is satisfied with the vehicle position, they should shift to PARK. The ⬙Active ParkSense Complete - Check Parking Position⬙ message will be momentarily displayed.
268 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! (Continued) WARNING! (Continued) might be temporarily detected or not detected at all. Obstacles located above or below the sensors will not be detected when they are in close proximity. • The vehicle must be driven slowly when using the ParkSense Active Park Assist system in order to be able to stop in time when an obstacle is detected. It is recommended that the driver looks over his/her shoulder when using the ParkSense Active Park Assist system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 269 NOTE: The ParkView Rear Back Up Camera has programmable modes of operation that may be selected through the Uconnect System. Refer to “Uconnect Settings” in “Understanding Your Instrument Panel” for further information. When the vehicle is shifted out of REVERSE (with camera delay turned OFF), the rear camera mode is exited and the navigation or audio screen appears again.
270 UNDERSTANDING THE FEATURES OF YOUR VEHICLE When enabled, active guide lines are overlaid on the Different colored zones indicate the distance to the rear of image to illustrate the width of the vehicle and its the vehicle. projected backup path based on the steering wheel The following table shows the approximate distances for position. each zone: When enabled, fixed guide lines are overlaid on the image to illustrate the width of the vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 271 CAUTION! (Continued) • To avoid vehicle damage, the vehicle must be driven slowly when using ParkView to be able to stop in time when an obstacle is seen. It is recommended that the driver look frequently over his/her shoulder when using ParkView. OVERHEAD CONSOLE The overhead console contains courtesy/reading lights and storage for sunglasses. Power sunroof and power sunshade switches may also be included, if equipped.
272 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Front Map/Reading Lights — With Center Buttons There are two map/reading light buttons located in the center of the overhead console that allow the lights to operate independently. Push the button once to turn the light on. To turn the light off, push the button a second time. Overhead Console — Power Sunroof Front Map/Reading Lights The front map/reading lights are mounted in the overhead console.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 273 NOTE: The lights also turn on when a door is opened. The two map/reading lights can be operated indepen- The lights will also turn on when the UNLOCK button on the RKE is pushed. dently by pushing the lenses. Sunglass Bin Door Push the lens once to turn the light on. Front Map/Reading Lights — With Push Lenses To turn the light off, push the lens a second time. The overhead console has a compartment which provides storage for a pair of sunglasses.
274 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Sunglass Bin Door — Rear Mounted Sunglass Bin Door — Front Mounted GARAGE DOOR OPENER — IF EQUIPPED HomeLink replaces up to three remote controls (handheld transmitters) that operate devices such as garage door openers, motorized gates, lighting or home security systems. The HomeLink unit operates off your vehicle’s battery.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 275 The HomeLink buttons that are located in the sun visor NOTE: HomeLink is disabled when the Vehicle Security designate the three different HomeLink channels. Alarm is active. The HomeLink indicator is located above the center button. WARNING! • Your motorized door or gate will open and close while you are training the universal transceiver. Do not train the transceiver if people, pets or other objects are in the path of the door or gate.
276 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! (Continued) • Vehicle exhaust contains carbon monoxide, a dangerous gas. Do not run your vehicle in the garage while training the transceiver. Exhaust gas can cause serious injury or death. NOTE: Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by federal safety standards. This includes most garage door opener models manufactured after 1982.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 277 Programming A Rolling Code For programming garage door openers that were manufactured after 1995. These garage door openers can be identified by the “LEARN” or “TRAIN” button located where the hanging antenna is attached to the garage door opener. It is NOT the button that is normally used to open and close the door. The name and color of the button may vary by manufacturer. 3 Training The Garage Door Opener 1 — Door Opener 2 — Training Button 1.
278 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm) away from the HomeLink button you wish to program while keeping the HomeLink indicator light in view. there may be a light that blinks when the garage door opener/device is in the LEARN/TRAIN mode. NOTE: You have 30 seconds in which to initiate the next 3. Push and hold the HomeLink button you want to step after the LEARN button has been pushed. program while you push and hold the hand-held 6.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 279 Reprogramming A Single HomeLink Button (Rolling Code) Programming A Non-Rolling Code For programming Garage Door Openers manufactured To reprogram a channel that has been previously trained, before 1995. follow these steps: 1. Place the ignition in the ON/RUN position. 1. Cycle the ignition to the ON/RUN position. 2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm) away from the HomeLink button you wish to program 2.
280 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 5. Push and hold the programmed HomeLink button and observe the indicator light. • If the indicator light stays on constantly, programming is complete and the garage door/device should activate when the HomeLink button is pushed. • To program the two remaining HomeLink buttons, repeat each step for each remaining button. DO NOT erase the channels. 3.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 281 2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm) NOTE: away from the HomeLink button you wish to program • If the indicator light stays on constantly, programwhile keeping the HomeLink indicator light in view. ming is complete and the garage door/device should activate when the HomeLink button is pushed. 3.
282 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Push and hold the desired HomeLink button until the To do this, push and hold the two outside buttons for 20 indicator light begins to flash after 20 seconds. Do not seconds until the red indicator flashes. Note that all channels will be erased. Individual channels cannot be release the button. erased. 3.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 283 If you have any problems, or require assistance, please call toll-free 1-800-355-3515 or, on the Internet at HomeLink.com for information or assistance. WARNING! • Vehicle exhaust contains carbon monoxide, a dangerous gas. Do not run your vehicle in the garage while programming the transceiver. Exhaust gas can cause serious injury or death. • Your motorized door or gate will open and close while you are programming the universal transceiver.
284 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: • The transmitter has been tested and it complies with FCC and IC rules. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the device. • The term IC before the certification/registration number only signifies that Industry Canada technical specifications were met.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 285 WARNING! WARNING! (Continued) • Never leave children unattended in a vehicle, or with access to an unlocked vehicle. Never leave the Key Fob in or near the vehicle, or in a location accessible to children. Do not leave the ignition of a vehicle equipped with Keyless Enter-N-Go in the ACC or ON/RUN mode. Occupants, particularly unattended children, can become entrapped by the power sunroof while operating the power sunroof switch.
286 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Opening Sunroof — Manual Mode movement and the sunroof will remain in a partially closed condition until the sunroof switch is pushed again. To open the sunroof, push and hold the switch rearward to full open. Any release of the switch will stop the Pinch Protect Feature movement.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 287 Sunshade Operation Sunroof Maintenance The sunshade can be opened manually. However, the Use only a non-abrasive cleaner and a soft cloth to clean sunshade will open automatically as the sunroof opens. the glass panel. NOTE: The sunshade cannot be closed if the sunroof is Ignition Off Operation open. The power sunroof switch will remain active for up to approximately ten minutes after the ignition switch is Wind Buffeting turned to the LOCK position.
288 UNDERSTANDING THE FEATURES OF YOUR VEHICLE POWER SUNROOF WITH POWER SHADE — IF EQUIPPED The power sunroof switches are located to the left between the sun visors on the overhead console. Power Shade Switches WARNING! Power Sunroof Switches The power shade switches are located to the right between the sun visors on the overhead console. • Never leave children unattended in a vehicle, or with access to an unlocked vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 289 WARNING! (Continued) accessible to children. Do not leave the ignition of a vehicle equipped with Keyless Enter-N-Go in the ACC or ON/RUN mode. Occupants, particularly unattended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death. • In a collision, there is a greater risk of being thrown from a vehicle with an open sunroof.
290 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Closing Sunroof — Express Push the switch forward and release it within one-half second and the sunroof will close automatically from any position. The sunroof will close fully and stop automatically. This is called “Express Close.” During Express Close operation, any other actuation of the switch will stop the sunroof. Closing Sunroof — Manual Mode sunroof position. During Express Vent operation, any movement of the switch will stop the sunroof.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 291 NOTE: If the sunroof is open, the shade will close to the half-open position. Pushing the shade close button again To open the shade, push and hold the switch rearward. will automatically close both the sunroof and shade The shade will open and stop automatically at the completely. half-open position. Push and hold the shade switch rearward again and the shade will open automatically to Closing Power Shade — Manual Mode the full-open position.
292 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: If three consecutive sunroof close attempts result Sunroof Maintenance in Pinch Protect reversals, the fourth close attempt will be Use only a non-abrasive cleaner and a soft cloth to clean a Manual Close movement with Pinch Protect disabled. the glass panel. Wind Buffeting Ignition Off Operation Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 293 POWER OUTLETS — IF EQUIPPED Your vehicle is equipped with 12 Volt (13 Amp) power outlets that can be used to power cellular phones, small electronics and other low powered electrical accessories. The power outlets are labeled with either a “key” or a “battery” symbol to indicate how the outlet is powered.
294 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Front Center Console Outlet NOTE: To ensure proper operation a MOPAR cigar knob and element must be used. • Do not exceed the maximum power of 160 Watts (13 Amps) at 12 Volts. If the 160 Watt (13 Amp) power rating is exceeded the fuse protecting the system will need to be replaced. • Power outlets are designed for accessory plugs only. Do not insert any other object in the power outlets as this will damage the outlet and blow the fuse.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 295 WARNING! (Continued) CAUTION! (Continued) • Do not touch with wet hands. • Close the lid when not in use and while driving the vehicle. • If this outlet is mishandled, it may cause an electric shock and failure. • Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.), will degrade the battery even more quickly. Only use these intermittently and with greater caution.
296 UNDERSTANDING THE FEATURES OF YOUR VEHICLE POWER INVERTER — IF EQUIPPED A 115 Volt (150 Watts Maximum) outlet is located on the forward wall of the center console storage bin, below the media center. This outlet can power cellular phones, electronics and other low power devices requiring power up to 150 Watts. Certain high-end video game consoles will exceed this power limit, as will most power tools. The power inverter is designed with built-in overload protection.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 297 WARNING! To avoid serious injury or death: • Do not insert any objects into the receptacles. • Do not touch with wet hands. • Close the lid when not in use. • If this outlet is mishandled, it may cause an electric shock and failure. 3 CUPHOLDERS Front Seat Cupholders The cupholders are located in the center console forward of the armrest between the front seats.
298 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Seat Cupholders The rear seat cupholders are located in the center armrest between the rear seats. The cupholders are positioned forward in the armrest and side-by-side to provide convenient access to beverage cans or bottles while maintaining a resting place for the rear occupant’s elbows.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 299 STORAGE Glove Compartment The glove compartment is located on the passenger side of the instrument panel. Pull on the release handle to open the glove compartment. NOTE: The glove compartment handle is equipped with a lock. To lock the glove compartment, remove the emergency key from the key fob, insert emergency key into glove compartment handle lock cylinder and turn the key to the lock position and remove the key.
300 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Console Features There is a storage compartment located under the center console armrest. The armrest can be slid forward/rearward to allow driver/passenger comfort position. WARNING! Do not operate this vehicle with a console compartment lid in the open position. Driving with the console compartment lid open may result in injury in a collision. There is a front center console storage area located under the center console cupholder.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 301 3 Center Console Cupholder Release Front Center Console Storage Located inside the center console storage compartment is a line that indicates how much storage is allowed.
302 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Storage Compartment Fill Line NOTE: Filling the console storage area above this line may impede the sliding of the cupholder. Located inside the front of the console storage area power cords can be routed from the storage area to the center console pass-through.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 303 Door Storage The door panels contain storage areas with a bottle holder.
304 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Seat Armrest Storage — If Equipped CARGO AREA FEATURES For rear passengers there is a storage bin located in the Cargo Area — 60/40 Split-Folding Rear Seat — If armrest. Lift upward on the latch to open the storage Equipped compartment. The 60/40 split-folding rear seat provides cargo-carrying versatility. The seatbacks fold down easily by pulling the seatback loops between the seatbacks and the bolsters.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 305 3 Rear Seatback Loops After releasing the seatback, it can be folded forward. Folded Rear Seatback When the seatback is folded to the upright position, make sure it is latched by strongly pulling on the top of the seatback above the seat strap.
306 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! WARNING! • Be certain that the seatback is securely locked into position. If the seatback is not securely locked into position, the seat will not provide the proper stability for child seats and/or passengers. An improperly latched seat could cause serious injury. • The cargo area in the rear of the vehicle (with the rear seatbacks in the locked-up or folded down position) should not be used as a play area by children when the vehicle is in motion.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 307 Grocery Bag Hooks The rear cargo area is equipped with grocery bag hooks, located on either side of the rear cargo area. Grocery Bag Hooks CAUTION! Do not exceed the maximum weight limit 35 lbs (16 kg) of the grocery bag hook. Damage may occur to hook and mounting surface.
308 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Ski Pass-Through REAR WINDOW FEATURES There is a ski pass-through door located behind the rear Rear Window Defroster seat armrest that allows longer items, such as snow skis, to be stored in the rear cargo area. Lower the armrest and The rear window defroster button is located on pull downward on the latch to open the ski pass-through the climate control. Push this button to turn on the door.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 309 CAUTION! Failure to follow these cautions can cause damage to the heating elements: • Use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements. Labels can be peeled off after soaking with warm water.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 INSTRUMENT PANEL FEATURES . . . . . . . . . .314 䡵 ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .352 䡵 INSTRUMENT CLUSTER — BASE . . . . . . . . . .315 ▫ Oil Change Reset . . . . . . . . . . . . . . . . . . . . .354 䡵 INSTRUMENT CLUSTER — PREMIUM . . . . . .318 ▫ Instrument Cluster Messages For (EVIC) And 䡵 WARNING AND INDICATOR LIGHTS . . . . . . .320 (DID) . . . . . . . . . . . . . . . . . . . . . . .
312 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ DID Selectable Menu Items . . . . . . . . . . . . . .370 䡵 RADIO OPERATION AND MOBILE DEVICES . .396 ▫ Screen Setup Driver Selectable Items . . . . . . . .374 ▫ Regulatory And Safety Information . . . . . . . . .396 䡵 UCONNECT SETTINGS . . . . . . . . . . . . . . . . . .376 䡵 CLIMATE CONTROLS . . . . . . . . . . . . . . . . . . .398 ▫ Buttons On The Faceplate. . . . . . . . . . . . . . . .377 ▫ Manual Climate Controls . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 313 ▫ Introducing Uconnect. . . . . . . . . . . . . . . . . . .421 ▫ Vehicle Health Alert . . . . . . . . . . . . . . . . . . .434 ▫ Get Started . . . . . . . . . . . . . . . . . . . . . . . . . .423 ▫ Register (8.4A/8.4AN) . . . . . . . . . . . . . . . . . .434 ▫ Basic Voice Commands. . . . . . . . . . . . . . . . . .424 ▫ Mobile App (8.4A/8.4AN) . . . . . . . . . . . . . . .435 ▫ Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
314 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT PANEL FEATURES 1 2 3 4 5 — Air Outlet — EVIC/DID Controls — Instrument Cluster — Cruise Controls — Ignition Switch 6 — Radio Screen 7 — Passenger Air Bag 8 — Glove Compartment 9 — Radio Controls 10 — Climate Controls 11 — Steering Wheel 12 — Hood Release 13 — Headlight Switch
UNDERSTANDING YOUR INSTRUMENT PANEL 315 INSTRUMENT CLUSTER — BASE 4 Base Electronic Vehicle Information Center (EVIC) Instrument Cluster
316 UNDERSTANDING YOUR INSTRUMENT PANEL 1. Tachometer 4. Fuel Gauge • Indicates the engine speed in revolutions per minute • The pointer shows the level of fuel in the fuel tank (RPM x 1000). when the ignition switch is in the ON/RUN position. to the side of the 2. Electronic Vehicle Information Center (EVIC) Display The fuel pump symbol points vehicle where the fuel door is located. • When the appropriate conditions exist, this display shows the Electronic Vehicle Information Center 5.
UNDERSTANDING YOUR INSTRUMENT PANEL 317 CAUTION! WARNING! Driving with a hot engine cooling system could damage your vehicle. If the temperature gauge reads “H” pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the “H”, turn the engine off immediately and call an authorized dealer for service. A hot engine cooling system is dangerous.
318 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER — PREMIUM Premium Driver Information Display (DID) Instrument Cluster
UNDERSTANDING YOUR INSTRUMENT PANEL 319 1. Tachometer 5. Temperature Gauge • Indicates the engine speed in revolutions per minute • The temperature gauge shows engine coolant tem(RPM x 1000). perature. Any reading within the normal range indicates that the engine cooling system is operating 2. Driver Information Display (DID) satisfactorily.
320 UNDERSTANDING YOUR INSTRUMENT PANEL WARNING! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call an authorized dealer for service if your vehicle overheats. If you decide to look under the hood yourself, see “Maintaining Your Vehicle”. Follow the warnings under the Cooling System Pressure Cap paragraph.
UNDERSTANDING YOUR INSTRUMENT PANEL 321 Red Telltale Indicator Lights Seat Belt Reminder Warning Light Red Telltale Light What It Means Seat Belt Reminder Warning Light When the ignition switch is first turned to ON/RUN, this light will turn on for four to eight seconds as a bulb check. During the bulb check, if the driver’s seat belt is unbuckled, a chime will sound.
322 UNDERSTANDING YOUR INSTRUMENT PANEL Air Bag Warning Light Red Telltale Light What It Means Air Bag Warning Light This light will turn on for four to eight seconds as a bulb check when the ignition switch is first turned to ON/RUN. If the light is either not on during starting, stays on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible.
UNDERSTANDING YOUR INSTRUMENT PANEL 323 Brake Warning Light Red Telltale Light United States Canada What It Means Brake Warning Light This light monitors various brake functions, including brake fluid level and parking brake application. If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the anti-lock brake system reservoir.
324 UNDERSTANDING YOUR INSTRUMENT PANEL The light will remain on until the cause is corrected. Brake Warning Light will turn on along with the ABS Light. Immediate repair to the ABS system is required. NOTE: The light may flash momentarily during sharp cornering maneuvers, which change fluid level condi- Operation of the Brake Warning Light can be checked by tions. The vehicle should have service performed, and turning the ignition switch from the OFF position to the the brake fluid level checked.
UNDERSTANDING YOUR INSTRUMENT PANEL 325 Vehicle Security Warning Light — If Equipped Red Telltale Light What It Means Vehicle Security Warning Light This light will flash at a fast rate for approximately 15 seconds when the vehicle security alarm is arming, and then will flash slowly until the vehicle is disarmed.
326 UNDERSTANDING YOUR INSTRUMENT PANEL Engine Temperature Warning Light Red Telltale Light What It Means Engine Temperature Warning Light This light warns of an overheated engine condition. If the engine coolant temperature is too high, this indicator will illuminate and a single chime will sound. If the light turns on while driving, safely pull over and stop the vehicle. If the A/C system is on, turn it off. Also, shift the transmission into NEUTRAL and idle the vehicle.
UNDERSTANDING YOUR INSTRUMENT PANEL 327 Charging System Warning Light Red Telltale Light What It Means Charging System Warning Light This light shows the status of the electrical charging system. If the light stays on or comes on while driving, turn off some of the vehicle’s nonessential electrical devices or increase engine speed (if at idle). If the charging system light remains on, it means that the vehicle is experiencing a problem with the charging system. Obtain SERVICE IMMEDIATELY.
328 UNDERSTANDING YOUR INSTRUMENT PANEL Oil Pressure Warning Light Red Telltale Light What It Means Oil Pressure Warning Light This light indicates low engine oil pressure. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. A chime will sound when this light turns on. Do not operate the vehicle until the cause is corrected. This light does not indicate how much oil is in the engine. The engine oil level must be checked under the hood.
UNDERSTANDING YOUR INSTRUMENT PANEL 329 Electronic Throttle Control (ETC) Warning Light Red Telltale Light What It Means Electronic Throttle Control (ETC) Warning Light This light informs you of a problem with the Electronic Throttle Control (ETC) system. If a problem is detected while the engine is running, the light will either stay on or flash depending on the nature of the problem.
330 UNDERSTANDING YOUR INSTRUMENT PANEL Transmission Temperature Warning Light Red Telltale Light What It Means Transmission Temperature Warning Light This light indicates that the transmission fluid temperature is running hot. This may occur with severe usage. If this light turns on, safely pull over and stop them vehicle. Then, shift the transmission into NEUTRAL and run the engine at idle or faster until the light turns off.
UNDERSTANDING YOUR INSTRUMENT PANEL 331 Electric Power Steering Fail Warning — If Equipped Red Telltale Light What It Means Electric Power Steering Fail Warning This light is used to manage the electrical warning of the EPS (Power Steering System). Refer to “Power Steering” in “Starting and Operating” for further information. Oil Temperature Warning Light Red Telltale Light What It Means Oil Temperature Warning Light This telltale indicates engine oil temperature is high.
332 UNDERSTANDING YOUR INSTRUMENT PANEL Door Open Warning Light Red Telltale Light What It Means Door Open Warning Light This indicator will illuminate when a door is ajar/open and not fully closed. If the vehicle is moving there will also be a single chime. Trunk Open Warning Light Red Telltale Light What It Means Trunk Open Warning Light This indicator will illuminate when the trunk is open and not fully closed.
UNDERSTANDING YOUR INSTRUMENT PANEL 333 Yellow Telltale Indicator Lights Engine Check/Malfunction Indicator Light (MIL) Yellow Telltale Light What It Means Engine Check/Malfunction Indicator Light (MIL) The Engine Check/Malfunction Indicator Light (MIL) is a part of an Onboard Diagnostic System called OBD II that monitors engine and automatic transmission control systems. The light will illuminate when the ignition is in the ON position before engine start.
334 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! WARNING! Prolonged driving with the Malfunction Indicator Light (MIL) on could cause damage to the engine control system. It also could affect fuel economy and driveability. If the MIL is flashing, severe catalytic converter damage and power loss will soon occur. Immediate service is required. A malfunctioning catalytic converter, as referenced above, can reach higher temperatures than in normal operating conditions.
UNDERSTANDING YOUR INSTRUMENT PANEL 335 Electronic Stability Control (ESC) Indicator Light — If Equipped Yellow Telltale Light What It Means Electronic Stability Control (ESC) Indicator Light The “ESC Indicator Light” in the instrument cluster will come on when the ignition switch is turned to the ON/RUN position. It should go out with the engine running. If the “ESC Indicator Light” comes on continuously with the engine running, a malfunction has been detected in the ESC system.
336 UNDERSTANDING YOUR INSTRUMENT PANEL Electronic Stability Control (ESC) OFF Indicator Light — If Equipped Yellow Telltale Light What It Means Electronic Stability Control (ESC) OFF Indicator Light This light indicates the Electronic Stability Control (ESC) is off. Low Washer Fluid Indicator Light — If Equipped Yellow Telltale Light What It Means Low Washer Fluid Indicator Light This indicator will illuminate when the windshield washer fluid is low.
UNDERSTANDING YOUR INSTRUMENT PANEL 337 Tire Pressure Monitoring Indicator Light Yellow Telltale Light What It Means Tire Pressure Monitoring Indicator Light The warning light switches on and a message is displayed to indicate that the tire pressure is lower than the recommended value and/or that slow pressure loss is occurring. In these cases, optimal tire duration and fuel consumption may not be guaranteed.
338 UNDERSTANDING YOUR INSTRUMENT PANEL on the vehicle placard or tire inflation pressure label, you Please note that the TPMS is not a substitute for proper should determine the proper tire inflation pressure for tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inflation has those tires. not reached the level to trigger illumination of the TPMS As an added safety feature, your vehicle has been low tire pressure telltale.
UNDERSTANDING YOUR INSTRUMENT PANEL 339 of reasons, including the installation of replacement or alternate tires or wheels on the vehicle that prevent the TPMS from functioning properly. Always check the TPMS malfunction telltale after replacing one or more tires or wheels on your vehicle, to ensure that the replacement or alternate tires and wheels allow the TPMS to continue to function properly. CAUTION! The TPMS has been optimized for the original equipment tires and wheels.
340 UNDERSTANDING YOUR INSTRUMENT PANEL Electronic Park Brake Fail Light Yellow Telltale Light What It Means Electronic Park Brake Fail Warning Light This telltale will turn on to indicate the Electronic Park Brake is not functioning properly and that service is required. Contact your authorized dealership. Low Fuel Indicator Light Yellow Telltale Light What It Means Low Fuel Indicator Light When the fuel level reaches approximately 3.0 gal (11.
UNDERSTANDING YOUR INSTRUMENT PANEL 341 Anti-Lock Brake (ABS) Indicator Light Yellow Telltale Light What It Means Anti-Lock Brake (ABS) Indicator Light This light monitors the Anti-Lock Brake System (ABS). The light will turn on when the ignition switch is placed in the ON/RUN position and may stay on for as long as four seconds. If the ABS light remains on or turns on while driving, then the Anti-Lock portion of the brake system is not functioning and service is required.
342 UNDERSTANDING YOUR INSTRUMENT PANEL Service Forward Collision Warning Indicator Light — If Equipped Yellow Telltale Light What It Means Service Forward Collision Warning Indicator Light This light warns the driver of a potential collision with the vehicle in front and prompts the driver to take action in order to avoid the collision. Refer to “Adaptive Cruise Control (ACC)” in “Understanding The Features Of Your Vehicle” for further information.
UNDERSTANDING YOUR INSTRUMENT PANEL 343 LaneSense Indicator Light — If Equipped Yellow Telltale Light What It Means LaneSense Indicator Light — If Equipped The LaneSense system provides the driver with visual and steering torque warnings when the vehicle starts to drift out of its lane unintentionally without the use of a turn signal. • When the LaneSense system senses a lane drift situation, the LaneSense indicator changes from solid green to solid yellow.
344 UNDERSTANDING YOUR INSTRUMENT PANEL LaneSense Failure Indicator Light — If Equipped Yellow Telltale Light What It Means LaneSense Failure Indicator Light This light will turn on when the LaneSense system is not operating and needs service. Please see your authorized dealer.
UNDERSTANDING YOUR INSTRUMENT PANEL 345 Loose Fuel Filler Cap Indicator Light — If Equipped Yellow Telltale Light What It Means Loose Fuel Filler Cap Indicator Light This light will illuminate when fuel filler cap is loose. Properly close the filler cap to disengage the light. If the light does not turn off, please see your authorized dealer.
346 UNDERSTANDING YOUR INSTRUMENT PANEL Green Telltale Indicator Lights Park/Headlight ON Indicator Light Green Telltale Light What It Means Park/Headlight ON Indicator Light This indicator will illuminate when the park lights or headlights are turned on. Front Fog Indicator Light — If Equipped Green Telltale Light What It Means Front Fog Indicator Light This indicator will illuminate when the front fog lights are on.
UNDERSTANDING YOUR INSTRUMENT PANEL 347 Turn Signal Indicator Lights Green Telltale Light What It Means Turn Signal Indicator Lights The instrument cluster arrow will flash independently for the LEFT or RIGHT turn signal as selected, as well as the exterior turn signal lamp(s) (front and rear) as selected when the multifunction lever is moved down (LEFT) or up (RIGHT). NOTE: • A continuous chime will sound if the vehicle is driven more than 1 mile (1.6 km) with either turn signal on.
348 UNDERSTANDING YOUR INSTRUMENT PANEL Electronic Speed Control SET Indicator Light Green Telltale Light What It Means Electronic Speed Control SET Indicator Light This light will turn on when the electronic speed control is SET. Refer to “Electronic Speed Control” in “Understanding The Features Of Your Vehicle” for further information.
UNDERSTANDING YOUR INSTRUMENT PANEL 349 Cruise Control Cancelled Light White Telltale Light What It Means Cruise Control Cancelled Light This light will turn on when the cruise control has been cancelled by the driver. Refer to “Electronic Speed Control” in “Understanding The Features Of Your Vehicle” for further information.
350 UNDERSTANDING YOUR INSTRUMENT PANEL Adaptive Cruise Control (ACC) Set Light — If Equipped White Telltale Light What It Means Adaptive Cruise Control (ACC) Set Light — If Equipped This light will turn on when the vehicle equipped with Adaptive Cruise Control (ACC) has reached the speed desired and the set button has been selected. For further information, refer to “Electronic Speed Control” in “Understanding The Features Of Your Vehicle.
UNDERSTANDING YOUR INSTRUMENT PANEL 351 Blue Telltale Indicator Light High Beam Indicator Light Blue Telltale Light What It Means High Beam Indicator Light This indicator shows that the high beam headlights are on. Push the multifunction control lever away from you to switch the headlights to high beam. Pull the lever toward you to switch the headlights back to low beam.
352 UNDERSTANDING YOUR INSTRUMENT PANEL ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) The EVIC Main Menu items consists of the following: • Speedometer The 3.5” Electronic Vehicle Information Center (EVIC) • Vehicle Info display is located in the instrument cluster.
UNDERSTANDING YOUR INSTRUMENT PANEL 353 The system allows the driver to select information by • UP Arrow Button pushing the following buttons mounted on the steering Push and release the UP arrow button to scroll wheel: upward through the Main Menu items ( Speedometer, Vehicle Info, Fuel Economy, Trip A, Trip B, Audio, Messages, Screen Set Up, Settings).
354 UNDERSTANDING YOUR INSTRUMENT PANEL • BACK/LEFT Arrow Button cycle based, which means the engine oil change interval may fluctuate, dependent upon your personal driving Push and release the LEFT arrow button to style. access the information screens or submenu Unless reset, this message will continue to display each screens of a main menu item. time the ignition is cycled to the ON/RUN position.
UNDERSTANDING YOUR INSTRUMENT PANEL 355 Secondary Method Of Navigating To The Oil Life Instrument Cluster Messages For (EVIC) And Screen In The DID And Holding OK (DID) 1. Without pushing the brake pedal, push the ENGINE • Front Seatbelts Unbuckled START/STOP button and cycle the ignition to the • Driver Seatbelt Unbuckled ON/RUN position (do not start the engine). • Passenger Seatbelt Unbuckled 2. Push and release the DOWN arrow button to scroll downward through the main menu to “Vehicle Info.
356 UNDERSTANDING YOUR INSTRUMENT PANEL • Service Power Steering • Service Electronic Throttle Control • Cruise Off • Lights On • Cruise Ready • Right Turn Signal Light Out • Cruise Set To XXX MPH • Left Turn Signal Light Out • Cruise Set To XXX KM/H • Turn Signal On • Tire Pressure Screen With Low Tire(s) “Inflate Tire to • XX” • • Service Tire Pressure System • • Parking Brake Engaged • • Brake Fluid Low • • Service Electronic Braking System • • Engine Temperature Hot • • Battery Voltage Low •
UNDERSTANDING YOUR INSTRUMENT PANEL 357 • Remote Start Aborted Hood Open • Service Transmission • Remote Start Aborted Trunk Open • Service Shifter • Remote Start Aborted Time Expired • Engage Park Brake to Prevent Rolling • Remote Start Disabled Start to Reset • Washer Fluid Low • Service Airbag System • Service Airbag Warning Light The Reconfigurable Telltales section is divided into the white telltales area on the right, amber telltales in the middle, and red telltales on the left.
358 UNDERSTANDING YOUR INSTRUMENT PANEL Vehicle Info Push and release the UP or DOWN arrow button until the Vehicle Info icon is highlighted in the EVIC/DID. Push and release the RIGHT arrow button and Coolant Temp will be displayed.
UNDERSTANDING YOUR INSTRUMENT PANEL 359 Fuel Economy Trip Info Push and release the UP or DOWN arrow button until Push and release the UP or DOWN arrow button until the Fuel Economy Menu item is highlighted in the DID. the Trip Menu item is highlighted in the EVIC (Toggle left or right to select Trip A or Trip B).
360 UNDERSTANDING YOUR INSTRUMENT PANEL Stored Messages Screen Setup Push and release the UP or DOWN arrow button until the Messages Menu displays in the EVIC/DID. This feature shows the number of stored warning messages. Pushing the RIGHT arrow button will allow you to see what the stored messages are. Push and release the UP or DOWN arrow button until the Screen Setup Menu displays in the EVIC/DID. Push and release the OK button to enter the sub-menus.
UNDERSTANDING YOUR INSTRUMENT PANEL 361 8 9 10 11 12 13 14 15 16 17 18 19 Settings Auto Unlock Doors Passive Entry Remote Unlock Sequence Key Fob Linked to Memory Remote Start Comfort System Sound Horn with Remote Start Sound Horn with Remote Lock Flash Lights with Lock Daytime Running Lights Automatic Highbeams Headlights On with Wipers Rain Sensing Wipers Translation Message Auto Unlock Doors Passive Entry Remote Unlock Key in Memory Rmt Start Comfort Submenu On, Off On, Off Driver Door, All Doors On,
362 UNDERSTANDING YOUR INSTRUMENT PANEL 20 Settings Headlights Off Delay Translation Message Lights Off Delay 21 Key-Off Power Delay Power Off Delay 22 Illuminated Approach Lights w/ Unlock 23 24 25 26 27 Easy Exit Seat Tilt Mirror in Reverse Compass variance Calibrate Compass Brake Service Easy Exit Seat Tilt Mirror in R Compass Var Compass Cal Brake Service 28 Auto Park Brake Auto Park Brake Submenu 0 seconds, 30 seconds, 60 seconds, 90 seconds Off, 45 seconds, 5 minutes, 10 minutes 0 seco
UNDERSTANDING YOUR INSTRUMENT PANEL 363 Screen Setup Driver Selectable Items • Time 1. Upper Left • Range To Empty (RTE) • None • Average Economy L/100km (or MPG) • Compass (default) • Current Economy L/100km (or MPG) • Outside Temp NOTE: Defaults will change to Average Economy L/100km (or MPG) UR, Range UL if the proxies for Compass and Outside Temp are not available • Time • Range To Empty (RTE) • Average Economy L/100km (or MPG) • Current Economy L/100km (or MPG) 2.
364 UNDERSTANDING YOUR INSTRUMENT PANEL • Current Economy DRIVER INFORMATION DISPLAY (DID) • Trip A The Driver Information Display (DID) features a driverinteractive display that is located in the instrument cluster. • Trip B • Audio Information • Menu Title (default) • Digital Speedo 4. Current Gear • On • Off (default) 5.
UNDERSTANDING YOUR INSTRUMENT PANEL 365 The DID Main Menu items consists of the following: • Speedometer • Vehicle Info • Driver Assist 4 • Fuel Economy Info • Trip (Trip A/Trip B) • Audio Info • Messages • Screen Setup The system allows the driver to select information by pushing the following buttons mounted on the steering wheel: DID Controls • UP Arrow Button Push and release the UP arrow button to scroll upward through the main menu and submenus (Speedometer, Vehicle Info, Driver Assist, Fuel Econo
366 UNDERSTANDING YOUR INSTRUMENT PANEL • DOWN Arrow Button • OK Button Push and release the DOWN arrow button to scroll downward through the main menu and submenus (Speedometer, Vehicle Info, Driver Assist, Fuel Economy, Trip Info, Audio, Messages, Screen Setup). Push the OK button to access/select the information screens or sub-menu screens of a main menu item. Push and hold the OK arrow button for one second to reset displayed/selected features that can be reset.
UNDERSTANDING YOUR INSTRUMENT PANEL 367 OK button. To reset the oil change indicator system (after 2. Push and release the DOWN arrow button to scroll performing the scheduled maintenance), refer to the downward through the main menu to “Vehicle Info.” following procedure. 3. Push and release the RIGHT arrow button to access 1. Without pushing the brake pedal, push the ENGINE the “Oil Life” screen. START/STOP button and cycle the ignition to the 4. Push and hold the OK button to reset of the Oil Life.
368 UNDERSTANDING YOUR INSTRUMENT PANEL • Service Airbag System • Traction Control Off • Washer Fluid Low • Oil Pressure Low • Oil Change Due • Fuel Low • Service Antilock Brake System • Service Electronic Throttle Control • Service Power Steering • Cruise Off • Cruise Ready • Cruise Set To XXX MPH • Cruise Set To XXX KM/H • Tire Pressure Screen With Low Tire(s) “Inflate Tire to XX” • Service Tire Pressure System • Parking Brake Engaged • Brake Fluid Low • Service Electronic Braking System • Engine Temper
UNDERSTANDING YOUR INSTRUMENT PANEL 369 • Vehicle Not in Park • Service Airbag Warning Light • Key in Ignition • Door Open • Key in Ignition Lights On • Doors Open • Remote Start Active Key to Run • Gear Not Available • Remote Start Active Push Start Button • Shift Not Allowed • Remote Start Aborted Fuel Low • Shift to Neutral then Drive or Reverse • Remote Start Aborted Too Cold • Transmission Getting Hot Push Brake • Remote Start Aborted Door Open • Trans.
370 UNDERSTANDING YOUR INSTRUMENT PANEL The Reconfigurable Telltales section is divided into the Temp will be displayed. Push the LEFT or RIGHT arrow white telltales area on the right, amber telltales in the button to scroll through the information sub-menus and push the OK button to select or reset the following middle, and red telltales on the left.
UNDERSTANDING YOUR INSTRUMENT PANEL 371 If the Tire Pressure system requires service, “Service Tire Adaptive Cruise Control (ACC) Menu — If Pressure System” is displayed. Equipped Tire PSI is an information only function and cannot be The DID displays the current ACC system settings. The reset. Push and release the LEFT arrow button to return information displayed depends on ACC system status. to the main menu.
372 UNDERSTANDING YOUR INSTRUMENT PANEL Push the SET + or the SET- button (located on the steering For further information, refer to “Adaptive Cruise Conwheel) and the following will display in the DID: trol (ACC) — If Equipped” in “Understanding The Features Of Your Vehicle.” ACC SET LaneSense Menu — If Equipped When ACC is set, the set speed will display in the The DID displays the current LaneSense system settings. instrument cluster.
UNDERSTANDING YOUR INSTRUMENT PANEL 373 – The Max and Min values will correspond to the Audio particular engine requirements Push and release the UP or DOWN arrow button until • Lower end of gauge will be displayed in an amber the Audio Menu displays in the EVIC/DID. color and turn green as Fuel Economy improves. Stored Messages • Hold OK to reset average fuel economy information. Push and release the UP or DOWN arrow button until the Messages Menu displays in the EVIC/DID.
374 UNDERSTANDING YOUR INSTRUMENT PANEL Screen Setup Driver Selectable Items • Time 1. Upper Left • Range • None • Average Economy L/100km (or MPG) • Compass • Current Economy L/100km (or MPG) • Outside Temp. (Default) NOTE: Defaults will change to Average Economy L/100km (or MPG) UR, Range UL if the proxies for Compass and Outside Temp are not available • Time • Range • Average Economy L/100km (or MPG) • Current Economy L/100km (or MPG) 2.
UNDERSTANDING YOUR INSTRUMENT PANEL 375 • Current L/100km (or MPG) 5. Odometer • Trip A Distance • On (Default) • Trip B Distance • Off • Audio Information 6. Fuel Gauge • Menu Title (Default ) • Standard (Default) • Digital Speedo • Range 4. Current Gear 7.
376 UNDERSTANDING YOUR INSTRUMENT PANEL UCONNECT SETTINGS The Uconnect system uses a combination of buttons on the touchscreen and buttons on the faceplate located on the center of the instrument panel that allows you to access and change the customer programmable features. Uconnect 5.
UNDERSTANDING YOUR INSTRUMENT PANEL 377 Buttons On The Faceplate Buttons are located below the Uconnect system in the center of the instrument panel. In addition, there is a Scroll/Enter control knob located on the right side of the Climate Controls in the center of the instrument panel. Turn the control knob to scroll through menus and change settings (i.e. 30, 60, 90) push the center of the control knob one or more times to select or change a setting (i.e. ON, OFF).
378 UNDERSTANDING YOUR INSTRUMENT PANEL Buttons On The Touchscreen NOTE: Only one category may be selected at a time. Buttons on the touchscreen are accessible on the To adjust the setting of a programmable feature, press the Uconnect display. desired setting option. Once in the desired setting option, press and release the preferred setting until a check-mark Customer Programmable Features/Personal appears next to the setting, showing that the setting has Settings — Uconnect 5.0/8.4A/8.
UNDERSTANDING YOUR INSTRUMENT PANEL 379 Display • Set Language After pressing the “Display” button on the touchscreen This feature allows you to select one of the languages for the following settings will be available: all display nomenclature, including the trip functions and the navigation system (if equipped).
380 UNDERSTANDING YOUR INSTRUMENT PANEL “Touchscreen Beep” button on the touchscreen until a touchscreen until a check-mark appears next to the check-mark appears next to the setting, showing that setting, showing that setting has been selected. setting has been selected.
UNDERSTANDING YOUR INSTRUMENT PANEL 381 • Set Time Minutes Safety & Driving Assistance This feature allows you to adjust the minutes. The “Sync with GPS Time” button on the touchscreen must be unchecked. To make your selection, press the “+” or “–” buttons on the touchscreen to adjust the minutes up or down. After pressing the “Safety & Driving Assistance” button on the touchscreen the following settings will be available: • Time Format This feature allows you to select the time format display setting.
382 UNDERSTANDING YOUR INSTRUMENT PANEL • Forward Collision Warning (FCW) Active Braking — If Equipped The FCW system includes Advanced Brake Assist (ABA). When this feature is selected, it will apply the brakes to slow your vehicle in case of potential forward collision. The ABA applies additional brake pressure when the driver requests insufficient brake pressure to avoid a potential frontal collision. The ABA system becomes active at 5 mph (8 km/h) and is only enabled when FCW is on.
UNDERSTANDING YOUR INSTRUMENT PANEL 383 Display. To change the ParkSense status, press and re- • Rear ParkSense Braking Assist — If Equipped lease the checkbox for “Sound” or “Sound and Display.” When this feature is selected, the ParkSense system will Refer to “ParkSense” in “Understanding The Features Of detect objects located behind the vehicle and utilize Your Vehicle” for system function and operating infor- autonomous braking to help stop the vehicle (only enmation. abled when ParkSense is also on).
384 UNDERSTANDING YOUR INSTRUMENT PANEL • Blind Spot Alert — If Equipped When this feature is selected, the Blind Spot Alert feature can be set to Off, Lights Only or Lights and Chime. The Blind Spot Alert feature can be activated in Lights category. When this category is selected, the Blind Spot Monitor (BSM) system is activated and will only show a visual alert in the outside mirrors.
UNDERSTANDING YOUR INSTRUMENT PANEL 385 • Rain Sensing Auto Wipers • Auto Park Brake When this feature is selected, the system will automatically activate the windshield wipers if it senses moisture on the windshield and the wipers are set to an intermittent position. To make your selection, press the “Rain Sensing” button on the touchscreen, until a check-mark appears next to the setting, showing that setting has been selected.
386 UNDERSTANDING YOUR INSTRUMENT PANEL touchscreen, and choose either 0 sec, 30 sec, 60 sec or 90 your selection, press the “Headlights With Wipers” butseconds. A check-mark appears next to setting indicating ton on the touchscreen, until a check-mark appears next to setting, indicating that the setting has been selected. that the setting has been selected.
UNDERSTANDING YOUR INSTRUMENT PANEL 387 • Flash Lights With Lock • Auto Unlock On Exit When this feature is selected, the hazard lights will flash when the doors are locked or unlocked with the Remote Keyless Entry (RKE) transmitter, or when using the passive entry feature. This feature may be selected with or without the sound horn on lock feature selected.
388 UNDERSTANDING YOUR INSTRUMENT PANEL • Sound Horn With Remote press of the Remote Keyless Entry (RKE) transmitter UNLOCK button. You must press the RKE transmitter UNLOCK button twice to unlock the passenger’s doors. When ⬙All Doors⬙ is selected for 1st Press Of Key Fob Unlocks, all doors will unlock on the first press of the RKE transmitter UNLOCK button. When this feature is selected, the horn will sound when the door locks are activated via the key fob.
UNDERSTANDING YOUR INSTRUMENT PANEL 389 • Passive Entry — If Equipped NOTE: The seat will return to the memorized seat location (if Recall Memory with Remote Key Unlock is set to ON) when the Remote Keyless Entry (RKE) transmitter is used to unlock the door. Refer to “Driver Memory Seat” in “Understanding The Features Of Your Vehicle” for further information.
390 UNDERSTANDING YOUR INSTRUMENT PANEL temperatures are above 80° F (26.7° C) the driver vented seat will turn on. To make your selection, press “Off,” “Remote Start Only,” OR “All Starts” checkbox until a check-mark appears next to the setting option. Select “Off,” “Remote Start Only” OR “All Starts” to determine when the feature is activated.
UNDERSTANDING YOUR INSTRUMENT PANEL 391 Audio • Speed Adjusted Volume After pressing the “Audio” button on the touchscreen the This feature increases or decreases volume relative to following settings will be available. vehicle speed. To change the Speed Adjusted Volume press the “Off,” “1,” “2” or “3” button on the touchscreen. • Balance/Fade This feature allows you to adjust the Balance and Fade • Surround Sound — If Equipped settings.
392 UNDERSTANDING YOUR INSTRUMENT PANEL Phone/Bluetooth • Channel Skip After pressing the “Phone/Bluetooth” button on the SiriusXM can be programmed to designate a group of touchscreen the following settings will be available: channels that are the most desirable to listen to, or to exclude undesirable channels while scanning.
UNDERSTANDING YOUR INSTRUMENT PANEL 393 Write down the SIRIUS ID numbers for your receiver. To are restored, a pop up appears stating ⬙settings reset to reactivate your service, either call the number listed on default.⬙ Press the okay button on the touchscreen to exit. the screen or visit the provider online. Clear Personal Data NOTE: SiriusXM Travel Link is a separate subscription After pressing the “Clear Personal Data Settings” button and is available for U.S. residents only.
394 UNDERSTANDING YOUR INSTRUMENT PANEL UCONNECT RADIOS — IF EQUIPPED For detailed information about your Uconnect radio, refer to your Uconnect Supplement Manual. USB PORT AND AUX JACK — IF EQUIPPED Located in the front storage area of the center console, this feature allows an external device, to be connected to the audio system. USB Port and AUX Jack 1 — USB Port 2 — AUX Jack For further information, refer to the Uconnect User’s Manual.
UNDERSTANDING YOUR INSTRUMENT PANEL 395 The right-hand control is a rocker-type switch with a pushbutton in the center and controls the volume and The remote sound system controls are located on the rear mode of the sound system. Pushing the top of the rocker surface of the steering wheel. Reach behind the wheel to switch will increase the volume, and pushing the bottom of the rocker switch will decrease the volume. access the switches.
396 UNDERSTANDING YOUR INSTRUMENT PANEL Radio Operation RADIO OPERATION AND MOBILE DEVICES Pushing the top of the switch will “Seek” up for the next Under certain conditions, the mobile device being on in listenable station and pushing the bottom of the switch your vehicle can cause erratic or noisy performance from will “Seek” down for the next listenable station. your radio. This condition may be lessened or eliminated by relocating the mobile device antenna.
UNDERSTANDING YOUR INSTRUMENT PANEL 397 Nevertheless, the wireless radio will be used in such a This device complies with Part 15 of the FCC Rules and manner that the radio is 20 cm or further from the human with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: body. The internal wireless radio operates within guidelines 1. This device may not cause harmful interference. found in radio frequency safety standards and recom2.
398 UNDERSTANDING YOUR INSTRUMENT PANEL • If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: CLIMATE CONTROLS The air conditioning and heating system is designed to make you comfortable in all types of weather.
UNDERSTANDING YOUR INSTRUMENT PANEL 399 Front Blower Control There are seven blower speeds. Use this control to regulate the amount of air forced through the system in any mode you select. The blower speed increases as you move the control clockwise from the OFF position.
400 UNDERSTANDING YOUR INSTRUMENT PANEL Air Conditioning Operation Push the A/C button to engage the Air Conditioning (A/C). An LED will illuminate when the A/C system is operating. MAX A/C For maximum cooling, when MAX A/C is selected the A/C is turned on automatically and the air is recirculated. A/C cannot be deselected when in MAX A/C position. The LED will blink three times if the A/C button is pushed.
UNDERSTANDING YOUR INSTRUMENT PANEL 401 Bi-Level Mode Mix Mode Air is directed through the panel and floor outlets. Air is directed through the floor, defrost and side window demist outlets. This setting works best in cold or snowy conditions that require extra heat at the NOTE: There is a difference in temperature (in any windshield. This setting is good for maintaining comfort, conditions other than full cold or full hot), between the while reducing moisture on the windshield.
402 UNDERSTANDING YOUR INSTRUMENT PANEL • In cold or damp weather, the use of the Recirculation mode will cause windows to fog on the inside because Push this button to choose between outside air intake or of moisture buildup inside the vehicle. For maximum recirculation of the air inside the vehicle. A LED will defogging, select the outside air position. illuminate when you are in Recirculation mode.
UNDERSTANDING YOUR INSTRUMENT PANEL 403 Manual Climate Controls With Touchscreen — If Equipped Buttons On Your Faceplate Buttons On Your Uconnect Touchscreen Buttons on the touchscreen are accessible on the Uconnect system screen. The buttons on the faceplate are located below the Uconnect touchscreen. 4 Uconnect 5.
404 UNDERSTANDING YOUR INSTRUMENT PANEL Button Descriptions (Applies To Both The Buttons On Your Faceplate And The Buttons On Your Touchscreen) 1. MAX A/C Button Press to change the current setting, the indicator illuminates when MAX A/C is ON. Performing this function again will cause the MAX A/C operation to switch into manual mode and the MAX A/C indicator will turn off. 2. A/C Button Uconnect 8.4A/8.
UNDERSTANDING YOUR INSTRUMENT PANEL 405 4. Front Defrost Button Press to change the current airflow setting to Defrost mode. The indicator illuminates when this feature is ON. Air comes from the windshield and side window demist outlets. When the defrost button is selected, the blower level will increase. Use Defrost mode with maximum temperature settings for best windshield and side window defrosting and defogging.
406 UNDERSTANDING YOUR INSTRUMENT PANEL 6. Blower Control 7. Modes Blower control is used to regulate the amount of air forced through the climate system. There are seven blower speeds available. Adjusting the blower will cause automatic mode to switch to manual operation.
UNDERSTANDING YOUR INSTRUMENT PANEL 407 • Bi-Level Mode NOTE: The air conditioning compressor operates in MIX and DEFROST modes even if the A/C button is not Air comes from the instrument panel outlets and pressed. This dehumidifies the air to help dry the windfloor outlets. A slight amount of air is directed shield. To improve fuel economy, use these modes only through the defrost and side window demister outlets. when necessary. NOTE: BI-LEVEL mode is designed under comfort con8.
408 UNDERSTANDING YOUR INSTRUMENT PANEL 10. Temperature Control Up Button (Uconnect 8.4) Automatic Climate Controls With Touchscreen — If Equipped Provides temperature control. Press the button on the faceplate for warmer temperature settings or on the Buttons On Your Faceplate touchscreen, press and slide the button on the touchscreen temperature bar towards the red arrow button on the touchscreen for warmer temperature settings. 11. Temperature Control (Uconnect 5.
UNDERSTANDING YOUR INSTRUMENT PANEL 409 Buttons On Your Uconnect Touchscreen The buttons on your faceplate are also accessible on the Uconnect system touchscreen. 4 Uconnect 8.4 Automatic Temperature Controls — Buttons On The Touchscreen Uconnect 5.0 Automatic Temperature Controls — Buttons On The Touchscreen Button Descriptions (Applies To Both The Buttons On Your Faceplate And The Buttons On Your Touchscreen) 1.
410 UNDERSTANDING YOUR INSTRUMENT PANEL again will cause the MAX A/C operation to switch into 5. Front Defrost Button manual mode and the MAX A/C indicator will turn off. Press to change the current airflow setting to Defrost 2. A/C Button mode. The indicator illuminates when this feature is ON. Air comes from the windshield and side window demist Press to change the current setting, the indicator illumioutlets. When the defrost button is selected, the blower nates when A/C is ON.
UNDERSTANDING YOUR INSTRUMENT PANEL 411 CAUTION! Failure to follow these cautions can cause damage to the heating elements: • Use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements. Labels can be peeled off after soaking with warm water. • Do not use scrapers, sharp instruments, or abrasive window cleaners on the interior surface of the window.
412 UNDERSTANDING YOUR INSTRUMENT PANEL 9. SYNC Buttons On Your Touchscreen Press the Sync button on the touchscreen to toggle the Sync feature On/Off. The Sync indicator is illuminated when this feature is enabled. Sync is used to synchronize the passenger temperature setting with the driver temperature setting. Changing the passenger temperature setting while in Sync will automatically exit this feature.
UNDERSTANDING YOUR INSTRUMENT PANEL 413 is a shut off wheel located adjacent to the air vanes to shut off or adjust the amount of airflow from these outlets. • Bi-Level Mode • Mix Mode Air comes from the floor, defrost and side window demist outlets. This mode works best in cold or snowy conditions. Air comes from the instrument panel outlets and 12. Climate Control OFF Button floor outlets. A slight amount of air is directed Press this button to turn the Climate Control ON/OFF.
414 UNDERSTANDING YOUR INSTRUMENT PANEL 14. Driver Temperature Control Up Button (Uconnect 8.4) Climate Control Functions Provides the driver with independent temperature control. Press the button on the faceplate for warmer temperature settings or on the touchscreen, press and slide the button on the touchscreen temperature bar towards the red arrow button on the touchscreen for warmer temperature settings. A/C (Air Conditioning) 15. Temperature Control (Uconnect 5.
UNDERSTANDING YOUR INSTRUMENT PANEL 415 • If your air conditioning performance seems lower than Recirculation Control expected, check the front of the A/C condenser (located in front of the radiator), for an accumulation of When outside air contains smoke, odors, or dirt or insects. Clean with a gentle water spray from high humidity, or if rapid cooling is desired, behind the radiator and through the condenser.
416 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: In cold weather, use of Recirculation mode may lead to excessive window fogging. The recirculation feature may be unavailable (recirculation button on touchscreen greyed out) if conditions exist that could create fogging on the inside of the windshield. On systems with Manual Climate Controls, the Recirculation mode is not allowed in Defrost mode to improve window clearing operation. Recirculation will be disabled automatically if this mode is selected.
UNDERSTANDING YOUR INSTRUMENT PANEL 417 NOTE: Manual Operation Override • It is not necessary to move the temperature settings for cold or hot vehicles. The system automatically adjusts the temperature, mode, and blower speed to provide comfort as quickly as possible. The system allows for manual selection of blower speed, air distribution mode, A/C status and recirculation control. • The temperature can be displayed in U.S. or Metric units by selecting the US/M customer-programmable feature.
418 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Tips Winter Operation NOTE: Refer to the chart at the end of this section for To ensure the best possible heater and defroster perforsuggested control settings for various weather condi- mance, make sure the engine cooling system is functioning properly and the proper amount, type, and concentions. tration of coolant is used.
UNDERSTANDING YOUR INSTRUMENT PANEL 419 Window Fogging Outside Air Intake Vehicle windows tend to fog on the inside of the glass in mild, rainy and/or humid weather. Windows may frost on the inside of the glass in very cold weather. To clear the windows, select Defrost or Mix mode and increase the front blower speed. Do not use the Recirculation mode without A/C for long periods, as fogging may occur.
420 UNDERSTANDING YOUR INSTRUMENT PANEL Control Setting Suggestions For Various Weather Conditions
UNDERSTANDING YOUR INSTRUMENT PANEL 421 2. Press and hold, then drag the selected App to replace an existing shortcut in the main menu bar. The Uconnect features and services in the main menu bar are easily changed for your convenience. Simply follow The replaced shortcut will now be an active App/ shortcut on the main menu bar. these steps: PERSONALIZED MENU BAR UCONNECT VOICE RECOGNITION QUICK TIPS Introducing Uconnect Start using Uconnect Voice Recognition with these helpful quick tips.
422 UNDERSTANDING YOUR INSTRUMENT PANEL Uconnect 5.0 Key Features: • 5” touchscreen • Three buttons on either side of the display Uconnect 8.4AN If you see the icon on your touchscreen, you have the Uconnect 8.4AN system. If not, you have a Uconnect 8.4A system.
UNDERSTANDING YOUR INSTRUMENT PANEL 423 Get Started All you need to control your Uconnect system with your voice are the buttons on your steering wheel. 1. Visit UconnectPhone.com to check mobile device and feature compatibility and to find phone pairing instructions. 4 2. Reduce background noise. Wind and passenger conversations are examples of noise that may impact recognition. 3. Speak clearly at a normal pace and volume while facing straight ahead.
424 UNDERSTANDING YOUR INSTRUMENT PANEL Basic Voice Commands The basic Voice Commands below can be given at any point while using your Uconnect system. Push the VR button . After the beep, sayѧ • Cancel to stop a current voice session • Help to hear a list of suggested Voice Commands • Repeat to listen to the system prompts again Notice the visual cues that inform you of your voice recognition system’s status. Cues appear on the touchscreen. Uconnect 5.
UNDERSTANDING YOUR INSTRUMENT PANEL 425 Radio Use your voice to quickly get to the AM, FM or SiriusXM Satellite Radio stations you would like to hear. (Subscription or included SiriusXM Satellite Radio trial required.) Push the VR button . After the beep, sayѧ • Tune to ninety-five-point-five FM • Tune to Satellite Channel Hits 1 Uconnect 8.4A/8.4AN TIP: At any time, if you are not sure of what to say or want to learn a Voice Command, push the VR button and say “Help.
426 UNDERSTANDING YOUR INSTRUMENT PANEL Uconnect 5.0 Radio Uconnect 8.4A/8.
UNDERSTANDING YOUR INSTRUMENT PANEL 427 TIP: Press the Browse button on the touchscreen to see all of the music on your AUX or USB device. Your Voice Uconnect offers connections via USB, SD, Bluetooth and Command must match exactly how the artist, album, auxiliary ports (If Equipped). Voice operation is only song and genre information is displayed. available for connected USB and AUX devices. (Remote CD player optional and not available on all vehicles.) Media 4 .
428 UNDERSTANDING YOUR INSTRUMENT PANEL Phone Making and answering hands-free phone calls is easy with Uconnect. When the Phonebook button is illuminated on your touchscreen, your system is ready. Check UconnectPhone.com for mobile phone compatibility and pairing instructions. . After the beep, say one of Push the Phone button the following commandsѧ • Call John Smith • Dial 123-456-7890 and follow the system prompts Uconnect 8.4A/8.
UNDERSTANDING YOUR INSTRUMENT PANEL 429 TIP: When providing a Voice Command, push the Phone and say “Call,” then pronounce the name button exactly as it appears in your phone book. When a contact has multiple phone numbers, you can say “Call John Smith work.” 4 Uconnect 8.4A/8.4AN Phone Uconnect 5.
430 UNDERSTANDING YOUR INSTRUMENT PANEL Voice Text Reply Uconnect will announce incoming text messages. Push and say Listen. (Must have comthe Phone button patible mobile phone paired to Uconnect system.) PRE-DEFINED VOICE TEXT REPLY RESPONSES I’ll call you I need See you in later. directions. of minutes. I’m on my way. Can’t talk right now. I’m lost. Thanks. 1. Once an incoming text message is read to you, push . After the beep, say: “Reply.
UNDERSTANDING YOUR INSTRUMENT PANEL 431 TIP: Voice Text Reply is not compatible with iPhone, but if your vehicle is equipped with Siri Eyes Free, you can use your voice to send a text message. Climate (8.4A/8.4AN) Too hot? Too cold? Adjust vehicle temperatures handsfree and keep everyone comfortable while you keep moving ahead. (If vehicle is equipped with climate control.) .
432 UNDERSTANDING YOUR INSTRUMENT PANEL TIP: Voice Command for Climate may only be used to adjust the interior temperature of your vehicle. Voice Command will not work to adjust the heated seats or steering wheel if equipped. Navigation (8.4A/8.4AN) The Uconnect navigation feature helps you save time and become more productive when you know exactly how to get to where you want to go. (Navigation is optional on the Uconnect 8.4A system. See your dealer to activate navigation at any time.) 1.
UNDERSTANDING YOUR INSTRUMENT PANEL 433 TIP: To start a POI search, push the VR button the beep, say: “ Find nearest coffee shop.” . After Uconnect Access (8.4A/8.4AN) WARNING! ALWAYS obey traffic laws and pay attention to the road. Some Uconnect Access services, including 9-1-1 and Assist, will NOT work without an operable 1X (voice/data) or 3G (data) network connection. NOTE: Your vehicle may be transmitting data as authorized by the subscriber. Uconnect 8.4A/8.
434 UNDERSTANDING YOUR INSTRUMENT PANEL WiFi Hotspot*** NOTE: Uconnect Access is available only on equipped vehicles purchased within the continental United States, **If vehicle is equipped. Alaska and Hawaii. Services can only be used where ***Extra charges apply. coverage is available; see coverage map for details. Vehicle Health Alert 9-1-1 Call Stolen Vehicle Assistance Your vehicle will send you an email alert if it senses a problem under the hood with one of your vehicles key systems.
UNDERSTANDING YOUR INSTRUMENT PANEL 435 For further information please visit DriveUconnect.com. Mobile App (8.4A/8.4AN) You’re only a few steps away from using remote commands and playing your favorite music in your vehicle. 4 2. Press the “Uconnect Care” button on the touchscreen. 3. A helpful Uconnect Care Agent will register your vehicle and handle all of the details. Signing up is easy! Simply follow the steps above.
436 UNDERSTANDING YOUR INSTRUMENT PANEL • Once you download the app to your compatible mobile device, you will also be able to start your 1. Download the Uconnect Access App to your mobile vehicle and lock/unlock its doors from virtually anydevice. where. 2. Press the Via Mobile icon on the navigation bar at the Voice Texting (8.4A/8.4AN) bottom of the app. 1. To send a message, push the Phone button . After 3. Press the app you’d like to connect to your vehicle.
UNDERSTANDING YOUR INSTRUMENT PANEL 437 You must be registered with Uconnect Access and have a compatible MAP – enabled smartphone to use your voice to send a personalized text message. For details about MAP, visit UconnectPhone.com. Apple iPhone iOS6 or later supports reading incoming text messages only.
438 UNDERSTANDING YOUR INSTRUMENT PANEL TIP: Yelp (8.4A/8.4AN) • Voice Texting is not compatible with iPhone, but if Once registered with Uconnect Access, you can use your your vehicle is equipped with Siri Eyes Free, you can voice to search for the most popular places or things around you. use your voice to send a text message. • Messages are limited to 140 characters. 1. Press the “Apps ” button on the touchscreen. • The Messaging button on the touchscreen must be 2.
UNDERSTANDING YOUR INSTRUMENT PANEL 439 TIP: Once you perform a search, you can reorganize the SiriusXM Travel Link (8.4A/8.4AN) results by selecting either the Best Match, Rating or Need to find a gas station, view local movie listings, Distance tab on the top of the touchscreen display. check a sports score or the 5 - day weather forecast? SiriusXM Travel Link is a suite of services that brings a wealth of information right to your Uconnect 8.4AN system. (Not available for 8.4A system.) .
440 UNDERSTANDING YOUR INSTRUMENT PANEL TIP: Traffic alerts are not accessible with Voice Com- Siri Eyes Free — If Equipped mand. If your vehicle is equipped with Siri Eyes Free, you can use your voice to send text messages, schedule meetings, set reminders, and more. For further information go to the Mopar Owner Connect website moparownerconnect.com.
UNDERSTANDING YOUR INSTRUMENT PANEL 441 • Create a custom auto reply message up to 160 characters. General Information NOTE: Only the first 25 characters can been seen on the This device complies with FCC rules Part 15 and Industry Canada RSS-210. Operation is subject to the following touchscreen while typing a custom message. two conditions: While in Do Not Disturb, Conference Call can be selected 1. This device may not cause harmful interference. so you can still place a second call without being inter2.
442 UNDERSTANDING YOUR INSTRUMENT PANEL Additional Information Uconnect System Support: © 2015 FCA US LLC. All rights reserved. Mopar and Uconnect are registered trademarks and Mopar Owner Connect is a trademark of FCA US LLC. Android is a trademark of Google Inc. SiriusXM and all related marks and logos are trademarks of SiriusXM Radio Inc. Yelp, Yelp logo, Yelp burst and related marks are registered trademarks of Yelp. • U.S.
STARTING AND OPERATING CONTENTS 䡵 STARTING PROCEDURES . . . . . . . . . . . . . . . .447 ▫ Brake/Transmission Shift Interlock System . . .453 ▫ Normal Starting. . . . . . . . . . . . . . . . . . . . . . .447 ▫ Nine-Speed Automatic Transmission . . . . . . . .453 ▫ Extreme Cold Weather (Below –22°F Or −30°C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .448 ▫ Gear Ranges . . . . . . . . . . . . . . . . . . . . . . . . .455 ▫ Extended Park Starting. . . . . . . . . . . . . . . . . .
444 STARTING AND OPERATING ▫ Flowing/Rising Water . . . . . . . . . . . . . . . . . .465 ▫ Brake Assist System (BAS) . . . . . . . . . . . . . . .478 ▫ Shallow Standing Water . . . . . . . . . . . . . . . . .466 ▫ Hill Start Assist (HSA) . . . . . . . . . . . . . . . . .478 䡵 POWER STEERING . . . . . . . . . . . . . . . . . . . . .467 ▫ Traction Control System (TCS) . . . . . . . . . . . .481 䡵 ELECTRIC PARK BRAKE (EPB) . . . . . . . . . . . .468 ▫ Electronic Stability Control (ESC) . . . . . . . .
STARTING AND OPERATING 445 䡵 TIRES — GENERAL INFORMATION . . . . . . . .500 䡵 TIRE ROTATION RECOMMENDATIONS . . . . .513 ▫ Tire Pressure . . . . . . . . . . . . . . . . . . . . . . . .500 䡵 TIRE PRESSURE MONITOR SYSTEM (TPMS) . .514 ▫ Tire Inflation Pressures . . . . . . . . . . . . . . . . .502 ▫ Base System . . . . . . . . . . . . . . . . . . . . . . . . .517 ▫ Tire Pressures For High Speed Operation . . . .503 ▫ Premium System — If Equipped . . . . . . . . . . .520 ▫ Radial Ply Tires . . . . . . . .
446 STARTING AND OPERATING 䡵 FLEXIBLE FUEL — IF EQUIPPED . . . . . . . . . . .529 ▫ Loose Fuel Filler Cap Message . . . . . . . . . . . .535 ▫ E-85 General Information . . . . . . . . . . . . . . .529 䡵 VEHICLE LOADING . . . . . . . . . . . . . . . . . . . .536 ▫ Ethanol Fuel (E-85) . . . . . . . . . . . . . . . . . . . .529 ▫ Certification Label . . . . . . . . . . . . . . . . . . . .536 ▫ Fuel Requirements . . . . . . . . . . . . . . . . . . . .530 䡵 TRAILER TOWING . . . . . . . . . . . . . . . . . .
STARTING AND OPERATING 447 STARTING PROCEDURES WARNING! (Continued) Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. WARNING! • When leaving the vehicle, always remove the Key Fob from the ignition and lock your vehicle. • Never leave children alone in a vehicle, or with access to an unlocked vehicle. • Allowing children to be in a vehicle unattended is dangerous for a number of reasons.
448 STARTING AND OPERATING Tip Start Feature 2. Cycle the ignition in the START position and release it when the engine starts. Cycle the ignition switch to START position and release it as soon as the starter engages. The starter motor will continue 3. If the engine fails to start within ten seconds, cycle the to run, but will automatically disengage itself when the ignition to the STOP (OFF/LOCK) position, wait five engine is running.
STARTING AND OPERATING 449 If Engine Fails To Start WARNING! • Never pour fuel or other flammable liquid into the throttle body air inlet opening in an attempt to start the vehicle. This could result in flash fire causing serious personal injury. • Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transmission cannot be started this way.
450 STARTING AND OPERATING CAUTION! To prevent damage to the starter, wait 10 to 15 seconds before trying again. After Starting The engine block heater cord is routed under the hood, behind to the driver’s side headlamp. Follow the steps below to properly use the engine block heater: 1. Locate the engine block heater cord (behind the driver’s side headlamp). The idle speed is controlled automatically and it will 2. Undo the Velcro strap that secures the heater cord in place.
STARTING AND OPERATING 451 • The engine block heater will require 110 Volts AC and AUTOMATIC TRANSMISSION 6.5 Amps to activate the heater element. • The engine block heater must be plugged in at least one hour to have an adequate warming effect on the engine. WARNING! Remember to disconnect the engine block heater cord before driving. Damage to the 110-115 Volt electrical cord could cause electrocution.
452 STARTING AND OPERATING WARNING! WARNING! (Continued) • It is dangerous to shift out of PARK or NEUTRAL if the engine speed is higher than idle speed. If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in reverse. You could lose control of the vehicle and hit someone or something. Only shift into gear when the engine is idling normally and your foot is firmly pressing the brake pedal.
STARTING AND OPERATING 453 NOTE: You must press and hold the brake pedal while Nine-Speed Automatic Transmission shifting out of PARK. The transmission is controlled using a rotary electronic gear selector located on the center console.
454 STARTING AND OPERATING self-calibrating; therefore, the first few shifts on a new vehicle may be somewhat abrupt. This is a normal condition, and precision shifts will develop within a few hundred miles (kilometers). Standard Shifter The standard transmission gear selector has PARK, REVERSE, NEUTRAL, DRIVE, and LOW shift positions. Using the LOW position manually downshifts the transThe nine-speed transmission has been developed to meet mission to a lower gear based on vehicle speed.
STARTING AND OPERATING 455 NOTE: In the event of a mismatch between the gear selector position and the actual transmission gear (for example, driver selects PARK while driving), the position indicator will blink continuously until the selector is returned to the proper position, or the requested shift can be completed. Gear Ranges DO NOT race the engine when shifting from PARK or NEUTRAL into another gear range.
456 STARTING AND OPERATING When parking on a hill, apply the parking brake before shifting the transmission to PARK. As an added precaution, turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade. WARNING! • Never use the PARK position as a substitute for the parking brake. Always apply the parking brake fully when parked to guard against vehicle movement and possible injury or damage. • Your vehicle could move and injure you and others if it is not in PARK.
STARTING AND OPERATING 457 WARNING! (Continued) CAUTION! • When leaving the vehicle, always make sure the ignition is in the OFF position, remove the Key Fob from the vehicle, and lock the vehicle. • Never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured.
458 STARTING AND OPERATING REVERSE (R) This range is for moving the vehicle backward. Shift into REVERSE only after the vehicle has come to a complete stop. NEUTRAL (N) CAUTION! Towing the vehicle, coasting, or driving for any other reason with the transmission in NEUTRAL can cause severe transmission damage. Refer to “Recreational Towing” in “Starting And Operating” and “Towing A Disabled Vehicle” in “What To Do In Emergencies” for further information.
STARTING AND OPERATING 459 During cold temperatures, transmission operation may be modified depending on engine and transmission temperature as well as vehicle speed. This feature improves warm up time of the engine and transmission to achieve maximum efficiency.
460 STARTING AND OPERATING In the event of a momentary problem, the transmission can be reset to regain all forward gears by performing the Use this range for engine braking when descending very following steps: steep grades. In this range, the transmission will downshift for increased engine braking. To access the LOW 1. Stop the vehicle. position, push down on the gear selector and rotate it 2. Shift the transmission into PARK, if possible. If not, fully clockwise. shift the transmission to NEUTRAL.
STARTING AND OPERATING 461 NOTE: Even if the transmission can be reset, we recommend that you visit your authorized dealer at your earliest possible convenience. Your authorized dealer has diagnostic equipment to determine if the problem could recur. If the transmission cannot be reset, authorized dealer service is required. Torque Converter Clutch A feature designed to improve fuel economy has been included in the automatic transmission on your vehicle.
462 STARTING AND OPERATING Operation In Paddle Shift mode, the transmission will shift up or down when (+/-) is manually selected by the driver, unless an engine lugging or overspeed condition would result. It will remain in the selected gear until another upshift or downshift is chosen, except as described below. When the transmission is in DRIVE or SPORT mode, it will operate automatically, shifting between the nine available gears.
STARTING AND OPERATING 463 • In either DRIVE or SPORT mode, the transmission will automatically downshift as the vehicle slows to a stop (to prevent engine lugging) and will display the current gear. Tapping the (+) paddle (at a stop) will allow starting in second gear. After a stop, the driver should manually upshift (+) the transmission as the vehicle accelerates. • If a requested downshift would cause the engine to over-speed, that shift will not occur.
464 STARTING AND OPERATING ALL WHEEL DRIVE (AWD) — IF EQUIPPED DRIVING ON SLIPPERY SURFACES This feature provides on-demand All-Wheel Drive (AWD). The system is automatic with no driver inputs or additional driving skills required. Under normal driving conditions, the front wheels provide most of the traction. If the front wheels begin to lose traction, power is shifted automatically to the rear wheels. The greater the front wheel traction loss, the greater the power transfer to the rear wheels.
STARTING AND OPERATING 465 Traction DRIVING THROUGH WATER When driving on wet or slushy roads, it is possible for a wedge of water to build up between the tire and road surface. This is hydroplaning and may cause partial or complete loss of vehicle control and stopping ability. To reduce this possibility, the following precautions should be observed: Driving through water more than a few inches/ centimeters deep will require extra caution to ensure safety and prevent damage to your vehicle. 1.
466 STARTING AND OPERATING Shallow Standing Water Although your vehicle is capable of driving through shallow standing water, consider the following Cautions and Warnings before doing so. WARNING! • Driving through standing water limits your vehicle’s traction capabilities. Do not exceed 5 mph (8 km/h) when driving through standing water. • Driving through standing water limits your vehicle’s braking capabilities, which increases stopping distances.
STARTING AND OPERATING 467 CAUTION! (Continued) WARNING! operate the vehicle if any fluid appears contaminated, as this may result in further damage. Such damage is not covered by the New Vehicle Limited Warranty. • Getting water inside your vehicle’s engine can cause it to lock up and stall out, and cause serious internal damage to the engine. Such damage is not covered by the New Vehicle Limited Warranty. Continued operation with reduced assist could pose a safety risk to yourself and others.
468 STARTING AND OPERATING The park brake is primarily intended to prevent the vehicle from rolling while parked. Before leaving the • Even if the power steering assistance is no longer vehicle, make sure that the park brake is applied. Also, be operational, it is still possible to steer the vehicle. certain to leave the transmission in PARK.
STARTING AND OPERATING 469 pedal while you apply the park brake, you may notice a small amount of brake pedal movement. The park brake can be applied even when the ignition switch if OFF, however, it can only be released when the ignition switch in the RUN position. NOTE: The EPB fault lamp will illuminate if the EPB switch is held for longer than 20 seconds in the applied position or 90 seconds in the released position. The light will extinguish upon releasing the switch.
470 STARTING AND OPERATING NOTE: When parking on a hill, it is important to turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade. Apply the park brake before placing the shift lever in PARK, otherwise the load on the transmission locking mechanism may make it difficult to move the shift lever out of PARK. The To release the parking brake manually, the ignition park brake should always be applied whenever the switch must be in the RUN position.
STARTING AND OPERATING 471 WARNING! (Continued) WARNING! (Continued) • Never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking brake, brake pedal or the transmission gear selector.
472 STARTING AND OPERATING If exceptional circumstances should make it necessary to engage the park brake while the vehicle is in motion, maintain upward pressure on the electric park brake switch for as long as engagement is desired. The BRAKE warning lamp will illuminate, and a continuous chime will sound. The rear stop lamps will also be illuminated automatically while the vehicle remains in motion. To disengage the park brake while the vehicle is in motion, release the switch.
STARTING AND OPERATING 473 the vehicle is left unsecured. If the automatic transmission is not in PARK, the seat belt is unbuckled, the driver door is open, the vehicle is at a standstill, and there is no attempt to depress the brake pedal or accelerator pedal, the park brake will automatically engage to prevent the vehicle from rolling. When servicing your rear brakes, it may be necessary for you or your technician push the rear piston into the rear caliper bore.
474 STARTING AND OPERATING While in service mode, the Electric Park Brake fault lamp BRAKE SYSTEM will flash continuously while the ignition switch is ON. Your vehicle is equipped with dual hydraulic brake When brake service work is complete, the following steps systems. If either of the two hydraulic systems loses must be followed to reset the parking brake system to normal capability, the remaining system will still function.
STARTING AND OPERATING 475 ELECTRONIC BRAKE CONTROL SYSTEM Brake System Warning Light Your vehicle is equipped with an advanced Electronic Brake Control system (EBC). This system includes Electronic Brake Force Distribution (EBD), Anti-Lock Brake System (ABS), Brake Assist System (BAS), Hill Start Assist (HSA), Traction Control System (TCS), Electronic Stability Control (ESC), and Electronic Roll Mitigation (ERM).
476 STARTING AND OPERATING and driven. During this self-check you may hear a slight clicking sound as well as some related motor noises. ABS is activated during braking when the system detects one or more wheels begins to lock. Road conditions such as ice, snow, gravel, bumps, railroad tracks, loose debris, or panic stops may increase the likelihood of ABS activation(s). You also may experience the following when ABS activates: • The ABS motor noise (it may continue to run for a short time after the stop).
STARTING AND OPERATING 477 WARNING! (Continued) • The ABS cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded. • The ABS cannot prevent collisions, including those resulting from excessive speed in turns, following another vehicle too closely, or hydroplaning.
478 STARTING AND OPERATING Brake Assist System (BAS) WARNING! The BAS is designed to optimize the vehicle’s braking capability during emergency braking maneuvers. The The Brake Assist System (BAS) cannot prevent the system detects an emergency braking situation by sens- natural laws of physics from acting on the vehicle, ing the rate and amount of brake application and then nor can it increase the traction afforded by prevailing applies optimum pressure to the brakes. This can help road conditions.
STARTING AND OPERATING 479 does not apply the throttle before this time expires, the system will release brake pressure and the vehicle will roll down the hill as normal. The following conditions must be met in order for HSA to activate: • The feature must be enabled. • The vehicle must be stopped. • Park brake must be off. • Driver door must be closed. • The vehicle must be on a sufficient grade. • The gear selection must match vehicle uphill direction (i.e.
480 STARTING AND OPERATING Towing With HSA WARNING! (Continued) HSA will also provide assistance to mitigate roll back while towing a trailer. WARNING! • Failure to follow these warnings can result in a collision or serious personal injury. Disabling And Enabling HSA • If you use a trailer brake controller with your trailer, the trailer brakes may be activated and deactivated with the brake switch.
STARTING AND OPERATING 481 For vehicles not equipped with the EVIC/DID, perform 8. Turn the ignition switch to the OFF position and then the following steps: back to the ON position. If the sequence was completed properly, the “ESC Off Indicator Light” will 1. Center the steering wheel (front wheels pointing blink several times to confirm HSA is disabled. straight forward). 9. Repeat these steps if you want to return this feature to 2. Shift the transmission into PARK. its previous setting. 3.
482 STARTING AND OPERATING to the wheel that is not spinning. BLD may remain • Understeer - when the vehicle is turning less than appropriate for the steering wheel position. enabled even if TCS and ESC are in a reduced mode. Electronic Stability Control (ESC) This system enhances directional control and stability of the vehicle under various driving conditions.
STARTING AND OPERATING 483 WARNING! (Continued) WARNING! (Continued) accidents, including those resulting from excessive speed in turns, driving on very slippery surfaces, or hydroplaning. ESC also cannot prevent accidents resulting from loss of vehicle control due to inappropriate driver input for the conditions. Only a safe, attentive, and skillful driver can prevent accidents.
484 STARTING AND OPERATING Partial Off The “Partial Off” mode is intended for times when a more spirited driving experience is desired. This mode may modify TCS and ESC thresholds for activation, which allows for more wheel spin than normally allowed. This mode may be useful if the vehicle becomes stuck.
STARTING AND OPERATING 485 ESC Activation/Malfunction Indicator Light and ESC OFF Indicator Light The “ESC Activation/Malfunction Indicator Light” (located in the instrument cluster) starts to flash as soon as the tires lose traction and the ESC system becomes active. The “ESC Activation/Malfunction Indicator Light” also flashes when TCS is active. If the “ESC Activation/ Malfunction Indicator Light” begins to flash during acceleration, ease up on the accelerator and apply as little throttle as possible.
486 STARTING AND OPERATING • The ESC system will make buzzing or clicking sounds cannot prevent wheel lift due to other factors, such as when it is active. This is normal; the sounds will stop road conditions, leaving the roadway, or striking objects when ESC becomes inactive following the maneuver or other vehicles. that caused the ESC activation. WARNING! The “ESC OFF Indicator Light” indicates the customer has elected to have the Electronic Stability Control (ESC) in a reduced mode.
STARTING AND OPERATING 487 Ready Alert Braking (RAB) Dynamic Steering Torque (DST) Ready Alert Braking may reduce the time required to reach full braking during emergency braking situations. It anticipates when an emergency braking situation may occur by monitoring how fast the throttle is released by the driver. The EBC will prepare the brake system for a panic stop.
488 STARTING AND OPERATING TIRE SAFETY INFORMATION NOTE: Tire Markings • P (Passenger) — Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designation. Example: P215/65R15 95H. • European — Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter ⬙P⬙ is absent from this tire size designation.
STARTING AND OPERATING 489 • Temporary spare tires are designed for temporary • High flotation tire sizing is based on U.S. design emergency use only. Temporary high pressure comstandards and it begins with the tire diameter molded pact spare tires have the letter “T” or “S” molded into into the sidewall. Example: 31x10.5 R15 LT. the sidewall preceding the size designation. Example: T145/80D18 103M.
490 STARTING AND OPERATING EXAMPLE: 65, 85, 80 = Aspect ratio in percent (%) – Ratio of section height to section width of tire, or 10.
STARTING AND OPERATING 491 EXAMPLE: H = Speed Symbol – A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions – The maximum speed corresponding to the speed symbol should only be achieved under specified operating conditions (i.e.
492 STARTING AND OPERATING Look for the TIN on the outboard side of black sidewall The TIN may be found on one or both sides of the tire, tires as mounted on the vehicle. If the TIN is not found on however, the date code may only be on one side. Tires the outboard side, then you will find it on the inboard side of the tire. with white sidewalls will have the full TIN, including the date code, located on the white sidewall side of the tire.
STARTING AND OPERATING 493 EXAMPLE: DOT MA L9 ABCD 0301 01 = Number representing the year in which the tire was manufactured (two digits) – 01 means the year 2001 – Prior to July 2000, tire manufacturers were only required to have one number to represent the year in which the tire was manufactured.
494 STARTING AND OPERATING Term Maximum Inflation Pressure Recommended Cold Tire Inflation Pressure Tire Placard Definition The maximum inflation pressure is the maximum permissible cold tire inflation pressure for this tire. The maximum inflation pressure is molded into the sidewall. Vehicle manufacturer’s recommended cold tire inflation pressure as shown on the tire placard.
STARTING AND OPERATING 495 Tire Loading And Tire Pressure Tire And Loading Information Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar or the rear edge of the driver’s side door.
496 STARTING AND OPERATING Tire And Loading Information Placard This placard tells you important information about the: 1. Number of people that can be carried in the vehicle. 2. Total weight your vehicle can carry. 3. Tire size designed for your vehicle. 4. Cold tire inflation pressures for the front, rear, and spare tires.
STARTING AND OPERATING 497 Loading To determine the maximum loading conditions of your vehicle, locate the statement “The combined weight of occupants and cargo should never exceed XXX lbs or XXX kg” on the Tire and Loading Information placard. The combined weight of occupants, cargo/luggage and trailer tongue weight (if applicable) should never exceed the weight referenced here. The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle.
498 STARTING AND OPERATING 4. The resulting figure equals the available amount of NOTE: cargo and luggage load capacity. For example, if • If your vehicle will be towing a trailer, load from your “XXX” amount equals 1,400 lbs (635 kg) and there will trailer will be transferred to your vehicle.
STARTING AND OPERATING 499 5
500 STARTING AND OPERATING WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.
STARTING AND OPERATING 501 WARNING! (Continued) • Unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • Always drive with each tire inflated to the recommended cold tire inflation pressure. Fuel Economy Underinflated tires will increase tire rolling resistance resulting in higher fuel consumption.
502 STARTING AND OPERATING Tire Inflation Pressures The proper cold tire inflation pressure is listed on the driver’s side B-Pillar or rear edge of the driver’s side door. At least once a month: Inflation pressures specified on the placard are always “cold tire inflation pressure”. Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least three hours, or driven less than 1 mile (1.6 km) after sitting for a minimum of three hours.
STARTING AND OPERATING 503 inflation pressure should be increased by 3 psi (21 kPa), which equals 1 psi (7 kPa) for every 12°F (7°C) for this outside temperature condition. Tire pressure may increase from 2 to 6 psi (13 to 40 kPa) during operation. DO NOT reduce this normal pressure build up or your tire pressure will be too low. Tire Pressures For High Speed Operation WARNING! High speed driving with your vehicle under maximum load is dangerous. The added strain on your tires could cause them to fail.
504 STARTING AND OPERATING Tire Repair Tire Types If your tire becomes damaged, it may be repaired if it All Season Tires — If Equipped meets the following criteria: All Season tires provide traction for all seasons (Spring, Summer, Fall and Winter). Traction levels may vary • The tire has not been driven on when flat. between different all season tires.
STARTING AND OPERATING 505 Summer tires do not contain the all season designation or mountain/snowflake symbol on the tire sidewall. Use Summer tires only in sets of four; failure to do so may adversely affect the safety and handling of your vehicle. WARNING! Do not use Summer tires in snow/ice conditions. You could lose vehicle control, resulting in severe injury or death. Driving too fast for conditions also creates the possibility of loss of vehicle control.
506 STARTING AND OPERATING While studded tires improve performance on ice, skid and traction capability on wet or dry surfaces may be poorer than that of non-studded tires. Some states prohibit studded tires; therefore, local laws should be checked before using these tire types. Run Flat Tires — If Equipped Spare Tires — If Equipped NOTE: For vehicles equipped with Tire Service Kit instead of a spare tire, please refer to “Tire Service Kit” in “What To Do In Emergencies” for further information.
STARTING AND OPERATING 507 rotation for your vehicle. If your vehicle has this option, Do not install a wheel cover or attempt to mount a refer to an authorized tire dealer for the recommended conventional tire on the compact spare wheel, since the wheel is designed specifically for the compact spare tire. tire rotation pattern. Do not install more than one compact spare tire and Compact Spare Tire — If Equipped wheel on the vehicle at any given time. The compact spare is for temporary emergency use only.
508 STARTING AND OPERATING front or rear axle of your vehicle, but it is not. This spare tire may have limited tread life. When the tread is worn to the tread wear indicators, the temporary use full size spare tire needs to be replaced. Since it is not the same as your original equipment tire, replace (or repair) the original equipment tire and reinstall on the vehicle at the first opportunity. Limited-Use Spare — If Equipped The limited-use spare tire is for temporary emergency use only.
STARTING AND OPERATING 509 Refer to “Freeing A Stuck Vehicle” in “What To Do In Emergencies” for further information. WARNING! Fast spinning tires can be dangerous. Forces generated by excessive wheel speeds may cause tire damage or failure. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 30 mph (48 km/h) for more than 30 seconds continuously when you are stuck, and do not let anyone near a spinning wheel, no matter what the speed.
510 STARTING AND OPERATING worn to the tread wear indicators, the tire should be replaced. Refer to “Replacement Tires” in this section for further information. Life Of Tire The service life of a tire is dependent upon varying factors including, but not limited to: • Driving style. WARNING! Tires and the spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure.
STARTING AND OPERATING 511 Information placard or the Vehicle Certification Label for the size designation of your tire. The Load Index and Speed Symbol for your tire will be found on the original equipment tire sidewall. See the Tire Sizing Chart example found in the “Tire Safety Information” section of this manual for more information relating to the Load Index and Speed Symbol of a tire. It is recommended to replace the two front tires or two rear tires as a pair.
512 STARTING AND OPERATING WARNING! (Continued) • Failure to equip your vehicle with tires having adequate speed capability can result in sudden tire failure and loss of vehicle control. CAUTION! Replacing original tires with tires of a different size may result in false speedometer and odometer readings. TIRE CHAINS (TRACTION DEVICES) Use of traction devices require sufficient tire-to-body clearance.
STARTING AND OPERATING 513 CAUTION! (Continued) important that only traction devices in good condition are used. Broken devices can cause serious damage. Stop the vehicle immediately if noise occurs that could indicate device breakage. Remove the damaged parts of the device before further use. • Install device as tightly as possible and then retighten after driving about ½ mile (0.8 km). • Do not exceed 30 mph (48 km/h).
514 STARTING AND OPERATING The suggested rotation method is the “forward cross” shown in the following diagram. This rotation pattern does not apply to some directional tires that must not be reversed. Tire Rotation TIRE PRESSURE MONITOR SYSTEM (TPMS) The Tire Pressure Monitor System (TPMS) will warn the driver of a low tire pressure based on the vehicle recommended cold placard pressure. The tire pressure will vary with temperature by approximately 1 psi (7 kPa) for every 12°F (6.5°C).
STARTING AND OPERATING 515 The TPMS will warn the driver of a low tire pressure if the tire pressure falls below the low-pressure warning limit for any reason, including low temperature effects and natural pressure loss through the tire. The TPMS will continue to warn the driver of low tire pressure as long as the condition exists, and will not turn off until the tire pressure is at or above the recommended cold placard pressure.
516 STARTING AND OPERATING NOTE: When filling warm tires, the tire pressure may need to be increased up to an additional 4 psi (30 kPa) above the recommended cold placard pressure in order to turn the Tire Pressure Monitoring Telltale Light off. CAUTION! • The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and warning have been established for the tire size equipped on your vehicle.
STARTING AND OPERATING 517 • Driving on a significantly underinflated tire causes the tire to overheat and can lead to tire failure. Underinflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability. Base System The Tire Pressure Monitor System (TPMS) uses wireless technology with wheel rim mounted electronic sensors to monitor tire pressure levels.
518 STARTING AND OPERATING Tire Pressure Monitoring Low Pressure Warnings The “Tire Pressure Monitoring Telltale Light” will illuminate in the instrument cluster, a “LOW TIRE PRESSURE” message will display in the instrument cluster, an ⬙Inflate to XX⬙ message will be displayed and a chime will sound when tire pressure is low in one or more of the four active road tires.
STARTING AND OPERATING 519 “Tire Pressure Monitoring Telltale Light” will turn off Vehicles With Compact Spare or non-Matching Full when the fault condition no longer exists. A system fault Size Spare can occur due to any of the following: 1. The compact spare tire or non-matching full size spare 1. Jamming due to electronic devices or driving next to tire does not have a tire pressure monitoring sensor.
520 STARTING AND OPERATING 4. For each subsequent ignition cycle, a chime will sound NOTE: It is particularly important for you to check the and the “TPMS Telltale Light” will flash on and off for tire pressure in all of the tires on your vehicle monthly and to maintain the proper pressure. 75 seconds and then remain on solid. 5.
STARTING AND OPERATING 521 Display (DID) will display an ⬙Inflate to XX⬙ message and recommended cold placard pressure value as shown in a graphic showing the pressure values of each tire with the ⬙Inflate to XX⬙ message. Once the system receives the updated tire pressures, the system will automatically the low tire pressure values in a different color.
522 STARTING AND OPERATING message will no longer display, and a pressure value will display in place of the dashes. A system fault can occur due to any of the following: 1. Jamming due to electronic devices or driving next to facilities emitting the same radio frequencies as the TPMS sensors. 2. Installing some form of aftermarket window tinting that affects radio wave signals. 3. Lots of snow or ice around the wheels or wheel housings. Tire Pressure Monitoring Service Warning 4.
STARTING AND OPERATING 523 4. For each subsequent ignition cycle, a chime will sound, the “TPMS Telltale Light” will flash on and off 1. The compact spare tire does not have a tire pressure for 75 seconds and then remain on solid, and the DID monitoring sensor. Therefore, the TPMS will not moniwill display a “SERVICE SYSTEM” message for five tor the pressure in the compact spare tire. seconds and then display dashes (- -) in place of the 2.
524 STARTING AND OPERATING General Information This device complies with Part 15 of the FCC rules and RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation.
STARTING AND OPERATING 525 Poor quality gasoline can cause problems such as hard Gasoline/Oxygenate Blends starting, stalling, and hesitations. If you experience these Some fuel suppliers blend unleaded gasoline with oxysymptoms, try another brand of gasoline before consid- genates such as ethanol. ering service for the vehicle. Reformulated Gasoline Many areas of the country require the use of cleaner burning gasoline referred to as “Reformulated Gasoline”.
526 STARTING AND OPERATING E-85 Usage In Non-Flex Fuel Vehicles Non-Flex Fuel Vehicles (FFV) are compatible with gasoline containing up to 15% ethanol (E-15). Gasoline with higher ethanol content may void the New Vehicle Limited Warranty. MMT In Gasoline Methylcyclopentadienyl Manganese Tricarbonyl (MMT) is a manganese-containing metallic additive that is blended into some gasoline to increase octane.
STARTING AND OPERATING 527 Materials Added To Fuel Besides using unleaded gasoline with the proper octane rating, gasolines that contain detergents, corrosion and stability additives are recommended. Using gasolines that have these additives will help improve fuel economy, reduce emissions, and maintain vehicle performance. Designated TOP TIER Detergent Gasoline contains a higher level of detergents to further aide in minimizing engine and fuel system deposits.
528 STARTING AND OPERATING CAUTION! (Continued) • The use of fuel additives, which are now being sold as octane enhancers, is not recommended. Most of these products contain high concentrations of methanol. Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsibility of the manufacturer and may void or not be covered under the New Vehicle Limited Warranty.
STARTING AND OPERATING 529 WARNING! (Continued) • Guard against carbon monoxide with proper maintenance. Have the exhaust system inspected every time the vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side windows fully open. FLEXIBLE FUEL — IF EQUIPPED E-85 General Information The information in this section is unique for Flexible Fuel vehicles only.
530 STARTING AND OPERATING Fuel Requirements NOTE: If your vehicle is E-85 compatible, it will operate on • Use seasonally adjusted E-85 fuel (ASTM D5798). With unleaded gasoline with any octane rating, or solely E-85 non-seasonally adjusted E-85 fuel, hard starting and fuel, or any mixture of these fuels.
STARTING AND OPERATING 531 Selection Of Engine Oil For Flexible Fuel Vehicles (E-85) And Gasoline Vehicles until the engine is fully warmed up. These issues may be improved with the use of seasonally adjusted E-85 fuel. FFV vehicles operated on E-85 require specially formulated engine oils. These special requirements are included in MOPAR engine oils, and in equivalent oils meeting FCA US Material Standard MS-6395.
532 STARTING AND OPERATING CAUTION! Replacing fuel system components with non-ethanol compatible components can damage your vehicle. Maintenance ADDING FUEL The fuel filler cap is located behind the fuel filler door, on the passenger side of the vehicle. If the fuel filler cap is lost or damaged, be sure the replacement fuel filler cap has been designed for use with this vehicle. CAUTION! Do not use ethanol mixture greater than 85% in your vehicle.
STARTING AND OPERATING 533 WARNING! CAUTION! • Never have any smoking materials lit in or near the vehicle when the gas cap is removed or the tank is being filled. • Never add fuel when the engine is running. This is in violation of most state and federal fire regulations and may cause the MIL to turn on. • A fire may result if gasoline is pumped into a portable container that is inside of a vehicle. You could be burned. Always place gas containers on the ground while filling.
534 STARTING AND OPERATING Fuel Filler Cap Release Fuel Filler Door and Fuel Filler Cap Tether Hook 3. Remove the fuel filler cap and hang fuel filler cap by 1 — Fuel Filler Door Actuator tether on fuel fill door to prevent damage to body side. 2 — Fuel Filler Cap Tether Hook 4. When the fuel nozzle “clicks” or shuts off, the fuel tank is full.
STARTING AND OPERATING 535 5. After you have stopped pumping fuel, remove the fuel Loose Fuel Filler Cap Message filler nozzle and replace the fuel filler cap. If the vehicle diagnostic system determines that the fuel 6. Tighten the fuel filler cap about one quarter turn until filler cap is loose, improperly installed, or damaged, a you hear one click.
536 STARTING AND OPERATING VEHICLE LOADING Certification Label rear axle systems (GAWR). Total load must be limited so GVWR and front and rear GAWR are not exceeded. Payload As required by National Highway Traffic Safety Administration regulations, your vehicle has a certification label The payload of a vehicle is defined as the allowable load weight a truck can carry, including the weight of the affixed to the driver’s side door or pillar. driver, all passengers, options and cargo.
STARTING AND OPERATING 537 Tire Size Curb Weight The tire size on the Vehicle Certification Label represents The curb weight of a vehicle is defined as the total weight the actual tire size on your vehicle. Replacement tires of the vehicle with all fluids, including vehicle fuel, at full must be equal to the load capacity of this tire size. capacity conditions, and with no occupants or cargo loaded into the vehicle.
538 STARTING AND OPERATING The entire vehicle should first be weighed on a commerCAUTION! cial scale to insure that the GVWR has not been exceeded. The weight on the front and rear of the vehicle should Do not load your vehicle any heavier than the GVWR then be determined separately to be sure that the load is or the maximum front and rear GAWR. If you do, properly distributed over the front and rear axle.
STARTING AND OPERATING 539 RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) Towing This Vehicle Behind Another Vehicle Towing Condition Wheel OFF the Ground Flat Tow Dolly Tow NONE Front Rear ALL On Trailer Front-Wheel Drive (FWD) Models NOT ALLOWED OK NOT ALLOWED OK All-Wheel Drive (AWD) Models NOT ALLOWED NOT ALLOWED NOT ALLOWED OK • When recreational towing your vehicle, always follow applicable state and provincial laws.
540 STARTING AND OPERATING Recreational Towing — Front-Wheel Drive (FWD) Models 7. Turn the ignition to the ON/RUN position, but do not start the engine. DO NOT flat tow this vehicle. Damage to the drivetrain 8. Press and hold the brake pedal. will result. 9. Release the parking brake. Recreational towing for front-wheel drive models is allowed ONLY if the front wheels are OFF the ground. 10. Turn the ignition OFF. This may be accomplished using a tow dolly or vehicle 11. Remove the Key Fob. trailer.
STARTING AND OPERATING 541 CAUTION! (Continued) • Towing this vehicle in violation of the above requirements can cause severe transmission damage. Damage from improper towing is not covered under the New Vehicle Limited Warranty. Recreational Towing — All-Wheel Drive (AWD) Models Recreational towing is not allowed. These models do not have a NEUTRAL (N) position in the power transfer unit. NOTE: This vehicle may be towed on a flatbed or vehicle trailer provided all four wheels are OFF the ground.
WHAT TO DO IN EMERGENCIES CONTENTS 䡵 HAZARD WARNING FLASHERS . . . . . . . . . . .545 䡵 JACKING AND TIRE CHANGING . . . . . . . . . .558 䡵 IF YOUR ENGINE OVERHEATS . . . . . . . . . . . .545 ▫ Jack Location/Spare Tire Stowage . . . . . . . . .559 䡵 WHEEL AND TIRE TORQUE SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . .546 ▫ Preparations For Jacking . . . . . . . . . . . . . . . .560 ▫ Torque Specifications . . . . . . . . . . . . . . . . . . .546 䡵 TIRE SERVICE KIT — IF EQUIPPED . . . . . . . .
544 WHAT TO DO IN EMERGENCIES 䡵 TOWING A DISABLED VEHICLE . . . . . . . . . . .581 ▫ Front-Wheel Drive (FWD) Models . . . . . . . . .584 ▫ All-Wheel Drive (AWD) Models . . . . . . . . . . .
WHAT TO DO IN EMERGENCIES 545 HAZARD WARNING FLASHERS IF YOUR ENGINE OVERHEATS The Hazard Warning flasher switch is located in the In any of the following situations, you can reduce the switch bank below the radio screen. potential for overheating by taking the appropriate action. Push the switch to turn on the Hazard Warning • On the highways — slow down. flasher.
546 WHAT TO DO IN EMERGENCIES CAUTION! Driving with a hot cooling system could damage your vehicle. If the temperature gauge reads “H,” pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the “H,” turn the engine off immediately and call for service. WHEEL AND TIRE TORQUE SPECIFICATIONS Proper lug nut/bolt torque is very important to ensure that the wheel is properly mounted to the vehicle.
WHAT TO DO IN EMERGENCIES 547 Inspect the wheel mounting surface prior to mounting Tighten the lug nuts/bolts in a star pattern until each the tire and remove any corrosion or loose particles. nut/bolt has been tightened twice. 6 Wheel Mounting Surface Torque Patterns After 25 miles (40 km) check the lug nut/bolt torque to be sure that all the lug nuts/bolts are properly seated against the wheel.
548 WHAT TO DO IN EMERGENCIES WARNING! To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle has been lowered. Failure to follow this warning may result in personal injury. Tire Service Kit Storage The Tire Service Kit is stowed under an access cover in the trunk. 1. Open the trunk. 2. Lift the access cover using the pull strap. TIRE SERVICE KIT — IF EQUIPPED Small punctures up to ¼” (6 mm) in the tire tread can be sealed with Tire Service Kit.
WHAT TO DO IN EMERGENCIES 549 3. Remove the fastener securing the Tire Service Kit. 4. Remove Tire Service Kit.
550 WHAT TO DO IN EMERGENCIES Tire Service Kit Components And Operation Tire Service Kit Usage Precautions • Replace the Tire Service Kit Sealant Bottle (1) and Sealant Hose (6) prior to the expiration date (printed at the lower right hand corner on the bottle label) to assure optimum operation of the system. Refer to “Sealing a Tire with Tire Service Kit” section (F) “Sealant Bottle and Hose Replacement”.
WHAT TO DO IN EMERGENCIES 551 from the vehicle or tire and wheel components. Once the sealant dries, it can easily be peeled off and properly discarded. • For optimum performance, make sure the valve stem on the wheel is free of debris before connecting the Tire Service Kit. • You can use the Tire Service Kit air pump to inflate bicycle tires.
552 WHAT TO DO IN EMERGENCIES WARNING! WARNING! (Continued) • Do not attempt to seal a tire on the side of the vehicle closest to traffic. Pull far enough off the road to avoid the danger of being hit when using the Tire Service Kit. • Do not use Tire Service Kit or drive the vehicle under the following circumstances: – If the puncture in the tire tread is approximately 1/4 inch (6 mm) or larger. – If the tire has any sidewall damage.
WHAT TO DO IN EMERGENCIES 553 WARNING! (Continued) • Tire Service Kit Sealant solution contains latex. In case of an allergic reaction or rash, consult a physician immediately. Keep Tire Service Kit out of reach of children. If swallowed, rinse mouth immediately with plenty of water and drink plenty of water. Do not induce vomiting! Consult a physician immediately. on the ground. This will provide the best positioning of the kit when injecting the sealant into the deflated tire and running the air pump.
554 WHAT TO DO IN EMERGENCIES 4. Remove the cap from the valve stem and then screw If the sealant (white fluid) does not flow within 0 – 10 the fitting at the end of the Sealant Hose (6) onto the seconds through the Sealant Hose (6): valve stem. 1. Push the Power Button (4) to turn Off the Tire Service Kit. Disconnect the Sealant Hose (6) from the valve 5. Uncoil the Power Plug (8) and insert the plug into the stem. Make sure the valve stem is free of debris. vehicle’s 12 Volt power outlet.
WHAT TO DO IN EMERGENCIES 555 If the sealant (white fluid) does flow through the If the tire does not inflate to at least 26 psi (1.8 Bar) Sealant Hose (6): pressure within 15 minutes: 1. Continue to operate the pump until sealant is no longer flowing through hose (typically takes 30 - 70 seconds). As the sealant flows through the Sealant Hose (6), the Pressure Gauge (3) can read as high as 70 psi (4.8 Bar). The Pressure Gauge (3) will decrease quickly from approximately 70 psi (4.
556 WHAT TO DO IN EMERGENCIES hose, and place the Tire Service Kit in the vehicle storage location. Quickly proceed to (D) “Drive Vehicle.” CAUTION! • The metal end fitting from Power Plug (8) may get hot after use, so it should be handled carefully. • Failure to reinstall the cap on the fitting at the end of the Sealant Hose (6) can result in sealant contacting your skin, clothing, and the vehicle’s interior.
WHAT TO DO IN EMERGENCIES 557 3. Uncoil the Air Pump Hose (7) (black in color) and 2. Disconnect the Tire Service Kit from the valve stem, screw the fitting at the end of hose (7) onto the valve reinstall the cap on the valve stem and unplug from 12 Volt outlet. stem. 4. Check the pressure in the tire by reading the Pressure 3. Place the Tire Service Kit in its proper storage area in Gauge (3). the vehicle. 4.
558 WHAT TO DO IN EMERGENCIES (F) Sealant Bottle And Hose Replacement: 1. Uncoil the Sealant Hose (6) (clear in color). 6. Verify that the cap is installed on the fitting at the end of the Sealant Hose (6) and return the hose to its storage area (located on the bottom of the air pump). 2. Locate the round Sealant Bottle release button in the 7. Return the Tire Service Kit to its storage location in the recessed area under the sealant bottle. vehicle. 3. Push the Sealant Bottle release button.
WHAT TO DO IN EMERGENCIES 559 WARNING! (Continued) 2. Lift the access cover using the pull strap. under a raised vehicle, take it to a service center where it can be raised on a lift. • Never start or run the engine while the vehicle is on a jack. • The jack is designed to be used as a tool for changing tires only. The jack should not be used to lift the vehicle for service purposes. The vehicle should be jacked on a firm level surface only. Avoid ice or slippery areas.
560 WHAT TO DO IN EMERGENCIES 3. Remove the fastener securing the jack and spare tire. 5. Remove the spare tire. WARNING! A loose tire or jack thrown forward in a collision or hard stop could endanger the occupants of the vehicle. Always stow the jack parts and the spare tire in the places provided. Have the deflated (flat) tire repaired or replaced immediately. Preparations For Jacking Jack And Spare Tire Fastener 4.
WHAT TO DO IN EMERGENCIES 561 WARNING! Do not attempt to change a tire on the side of the vehicle close to moving traffic, pull far enough off the road to avoid being hit when operating the jack or changing the wheel. 2. Turn on the Hazard Warning flasher. 3. Set the parking brake. 4. Place the shifter into the park position. 5. Turn the ignition off to the LOCK position. 6. Chock both the front and rear of the wheel diagonally opposite of the jacking position.
562 WHAT TO DO IN EMERGENCIES WARNING! (Continued) • Never start or run the engine with the vehicle on a jack. • Do not let anyone sit in the vehicle when it is on a jack. • Do not get under the vehicle when it is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift. • Only use the jack in the positions indicated and for lifting this vehicle during a tire change. • If working on or near a roadway, be extremely careful of motor traffic.
WHAT TO DO IN EMERGENCIES 563 NOTE: The jack handle attaches to the side of the jack with two attachment points. When the jack is partially expanded, the tension between the two attachment points holds the jack handle in place. 6 Jacking Locations 1. Remove the jack, wheel bolt wrench and wheel chocks from the spare wheel as an assembly. Remove the chocks from the jack assembly.
564 WHAT TO DO IN EMERGENCIES 2. Chock both the front and rear of the wheel diagonally opposite of the jacking position. For example, if changing the right front tire, chock the left rear wheel. Place both chocks under the tire. 3. If equipped with aluminum wheels where the center cap covers the wheel bolts, use the wheel bolt wrench to pry the center cap off carefully before raising the vehicle. 4.
WHAT TO DO IN EMERGENCIES 565 6 Rear Body Flange Front Body Flange Engaged
566 WHAT TO DO IN EMERGENCIES Rear Body Flange Engaged 6. Turn the jack screw clockwise to firmly engage the jack saddle with the lift area of the sill flange, centering the jack saddle between the locating notches on the sill flange. 7. Raise the vehicle just enough to remove the flat tire and install the spare tire.
WHAT TO DO IN EMERGENCIES 567 8. Remove the wheel bolts and tire. 9. Mount the spare tire. CAUTION! Be sure to mount the spare tire with the valve stem facing outward. The vehicle could be damaged if the spare tire is mounted incorrectly. 6 Rear Jacking Location WARNING! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire.
568 WHAT TO DO IN EMERGENCIES NOTE: • For vehicles so equipped, do not attempt to install a center cap or wheel cover on the compact spare. • Refer to “Compact Spare Tire” and to “Limited-Use Spare” under “Tires—General Information” in “Starting and Operating” for additional warnings, cautions, and information about the spare tire, its use, and operation. Mounting Spare Tire 10. Install the wheel bolts with the threaded end of the wheel bolt toward the wheel. Lightly tighten the wheel bolts.
WHAT TO DO IN EMERGENCIES 569 11. Lower the vehicle to the ground by turning the jack handle counterclockwise. WARNING! 12. Finish tightening the wheel bolts. Push down on the A loose tire or jack thrown forward in a collision or wrench while at the end of the handle for increased hard stop could endanger the occupants of the veleverage. Tighten the wheel bolts in a star pattern hicle. Always stow the jack parts and the spare tire in until each wheel bolt has been tightened twice.
570 WHAT TO DO IN EMERGENCIES snapping the cover over the two wheel bolts. Do not use a hammer or excessive force to install the cover. 4. Install the remaining wheel bolts and lightly tighten. WARNING! To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle has been lowered. Failure to follow this warning may result in serious injury. Tire And Wheel Cover Or Center Cap 1 — Valve Stem 2 — Valve Notch 3 — Wheel Bolt 4 — Wheel Cover 5 — Road Wheel 5.
WHAT TO DO IN EMERGENCIES 571 bolt torque. If in doubt about the correct tightness, have them checked with a torque wrench by your authorized dealer or service station. WARNING! To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle has been lowered. Failure to follow this warning may result in serious injury. 7. Lower the jack until it is free. Remove the wheel chocks. Reassemble the lug wrench to the jack assembly and stow it in the spare tire area.
572 WHAT TO DO IN EMERGENCIES 5. Lower the jack until it is free. Remove the wheel NOTE: When using a portable battery booster pack chocks. Reassemble the lug wrench to the jack assem- follow the manufacturer’s operating instructions and bly and stow it in the spare tire area. Secure the precautions. assembly using the means provided. Release the parking brake before driving the vehicle. CAUTION! 6.
WHAT TO DO IN EMERGENCIES 573 Preparations For Jump-Start The battery in your vehicle is located in the front of the engine compartment, behind the left headlight assembly. WARNING! • Take care to avoid the radiator cooling fan whenever the hood is raised. It can start anytime the ignition switch is ON. You can be injured by moving fan blades. • Remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact. You could be seriously injured.
574 WHAT TO DO IN EMERGENCIES 3. If using another vehicle to jump-start the battery, park the vehicle within the jumper cables reach, set the parking brake and make sure the ignition is OFF. WARNING! Do not allow vehicles to touch each other as this could establish a ground connection and personal injury could result. Jump-Starting Procedure WARNING! Failure to follow this jump-starting procedure could result in personal injury or property damage due to battery explosion.
WHAT TO DO IN EMERGENCIES 575 WARNING! Do not connect the jumper cable to the negative (-) post of the discharged battery. The resulting electrical spark could cause the battery to explode and could result in personal injury. Only use the specific ground point, do not use any other exposed metal parts. 6. Once the engine is started, remove the jumper cables in the reverse sequence: Disconnecting The Jumper Cables 1.
576 WHAT TO DO IN EMERGENCIES CAUTION! Accessories plugged into the vehicle power outlets draw power from the vehicle’s battery, even when not in use (i.e., cellular devices, etc.). Eventually, if plugged in long enough without engine operation, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting. NOTE: Shifts between DRIVE and REVERSE can only be achieved at wheel speeds of 5 mph (8 km/h) or less.
WHAT TO DO IN EMERGENCIES 577 CAUTION! CAUTION! (Continued) Racing the engine or spinning the wheels may lead to transmission overheating and failure. Allow the engine to idle with the transmission in NEUTRAL for at least one minute after every five rocking-motion cycles. This will minimize overheating and reduce the risk of transmission failure during prolonged efforts to free a stuck vehicle.
578 WHAT TO DO IN EMERGENCIES MANUAL PARK RELEASE WARNING! Always secure your vehicle by fully applying the parking brake, before activating the Manual Park Release. Activating the Manual Park Release will allow your vehicle to roll away if it is not secured by the parking brake or by proper connection to a tow vehicle. Activating the Manual Park Release on an unsecured vehicle could lead to serious injury or death for those in or around the vehicle.
WHAT TO DO IN EMERGENCIES 579 6 Manual Park Release Cover Manual Park Release Tether 3. Unsnap the tether from the Manual Park Release lever, 4. Pull the tether to rotate the lever up and rearward, and use it to pull the lever upwards. until it locks vertically in place. Verify that the Manual Park Release lever is locked in the released position.
580 WHAT TO DO IN EMERGENCIES To reset the Manual Park Release: 1. Pull the tether upwards to unlock the lever. 2. Rotate the Manual Park Release lever forward and down to its original position. 3. Re-install the access cover and the rubber storage bin liner. Locked Position 5. The vehicle is now out of PARK and can be moved. Release the parking brake only when the vehicle is securely connected to a tow vehicle.
WHAT TO DO IN EMERGENCIES 581 TOWING A DISABLED VEHICLE This section describes procedures for towing a disabled vehicle using a commercial towing service. Towing Condition Flat Tow Wheel Lift Or Dolly Tow Flatbed Wheel OFF the Ground NONE Front Rear ALL FWD MODELS NOT ALLOWED OK NOT ALLOWED BEST METHOD AWD MODELS NOT ALLOWED NOT ALLOWED NOT ALLOWED ONLY METHOD Proper towing or lifting equipment is required to prevent NOTE: damage to your vehicle.
582 WHAT TO DO IN EMERGENCIES • Vehicles with a discharged battery or total electrical • Use approved receptacle location to free the disabled failure when the electric parking brake (EPB) is envehicle from its environment. gaged, will need a wheel dolly or jack to raise the rear wheels off the ground when moving the vehicle onto a flatbed.
WHAT TO DO IN EMERGENCIES 583 CAUTION! Recovery feature: • Is to be used by a professional ONLY. • Is used only to provide recovery of the vehicle. • Is NOT to be used to recover secondary vehicle. • Is NOT to be used for transporting the vehicle over the road, i.e. “Flat Towing”. Recovery load should: • Be applied at constant speed. • Be applied parallel to the center line of the length of the vehicle. • Not be an abrupt acceleration. If you must use the accessories (wipers, defrosters, etc.
584 WHAT TO DO IN EMERGENCIES CAUTION! • Do not use sling-type equipment when towing. Vehicle damage may occur. • When securing the vehicle to a flatbed truck, do not attach to front or rear suspension components. Damage to your vehicle may result from improper towing. • Ensure that the Electric Park Brake is released, and remains released, while being towed. NOTE: Ensure that the Electric Park Brake is released, and remains released, while being towed.
WHAT TO DO IN EMERGENCIES 585 CAUTION! • DO NOT tow this vehicle with ANY of its wheels on the ground. Damage to the drivetrain will result. • Front or rear wheel lifts must not be used. Internal damage to the transmission or power transfer unit will occur if a front or rear wheel lift is used when towing. • Towing this vehicle in violation of the above requirements can cause severe transmission and/or power transfer unit damage.
MAINTAINING YOUR VEHICLE CONTENTS 䡵 ENGINE COMPARTMENT — 2.4L . . . . . . . . . .589 ▫ Engine Oil Filter . . . . . . . . . . . . . . . . . . . . . .598 䡵 ENGINE COMPARTMENT — 3.6L . . . . . . . . . .590 ▫ Engine Air Cleaner Filter . . . . . . . . . . . . . . . .599 䡵 ONBOARD DIAGNOSTIC SYSTEM — OBD II . .591 ▫ Maintenance-Free Battery . . . . . . . . . . . . . . .599 ▫ Loose Fuel Filler Cap Message . . . . . . . . . . . .591 ▫ Air Conditioner Maintenance . . . . . . . . . . . . .
588 MAINTAINING YOUR VEHICLE ▫ Automatic Transmission . . . . . . . . . . . . . . . .616 ▫ Front Side Marker Lamps . . . . . . . . . . . . . . .646 ▫ Appearance Care And Protection From Corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . .618 ▫ Front Fog Lamp . . . . . . . . . . . . . . . . . . . . . .647 䡵 FUSES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .625 ▫ Power Distribution Center (Fuses) . . . . . . . . . .626 ▫ Interior Fuses . . . . . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 589 ENGINE COMPARTMENT — 2.
590 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT — 3.
MAINTAINING YOUR VEHICLE 591 ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated Onboard Diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
592 MAINTAINING YOUR VEHICLE further information. Tighten the fuel filler cap until a “clicking” sound is heard. This is an indication that the fuel filler cap is properly tightened. Refer to “Onboard Diagnostic System” in “Maintaining Your Vehicle” for further information. Normally, the OBD II system will be ready. The OBD II system may not be ready if your vehicle was recently serviced, recently had a dead battery or a battery replacement.
MAINTAINING YOUR VEHICLE 593 3. Approximately 15 seconds later, one of two things will system to update. A recheck with the above test routine happen: may then indicate that the system is now ready. • The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine. This means that your vehicle’s OBD II system is not ready and you should not proceed to the I/M station.
594 MAINTAINING YOUR VEHICLE DEALER SERVICE MAINTENANCE PROCEDURES Your authorized dealer has the qualified service personnel, special tools, and equipment to perform all service operations in an expert manner. Service Manuals are available which include detailed service information for your vehicle. Refer to these Service Manuals before attempting any procedure yourself. The pages that follow contain the required maintenance services determined by the engineers who designed your vehicle.
MAINTAINING YOUR VEHICLE 595 CAUTION! (Continued) • Your vehicle has been built with improved fluids that protect the performance and durability of your vehicle and also allow extended maintenance intervals. Do not use chemical flushes in these components as the chemicals can damage your engine, transmission or air conditioning. Such damage is not covered by the New Vehicle Limited Warranty. If a flush is needed because of component malfunction, use only the specified fluid for the flushing procedure.
596 MAINTAINING YOUR VEHICLE CAUTION! Overfilling or underfilling the crankcase will cause aeration or loss of oil pressure. This could damage your engine. Change Engine Oil Engine Oil Selection For best performance and maximum protection under all types of operating conditions, the manufacturer only recommends engine oils that are API Certified and meet the requirements of FCA US Material Standard MS-6395.
MAINTAINING YOUR VEHICLE 597 CAUTION! Do not use chemical flushes in your engine oil as the chemicals can damage your engine. Such damage is not covered by the New Vehicle Limited Warranty. Lubricants which do not have both the engine oil certification mark and the correct SAE viscosity grade number should not be used. Engine Oil Viscosity — 3.
598 MAINTAINING YOUR VEHICLE Lubricants which do not have both the engine oil certi- Disposing Of Used Engine Oil And Oil Filters fication mark and the correct SAE viscosity grade num- Care should be taken in disposing of used engine oil and ber should not be used. oil filters from your vehicle. Used oil and oil filters, indiscriminately discarded, can present a problem to the Synthetic Engine Oils environment.
MAINTAINING YOUR VEHICLE 599 Engine Air Cleaner Filter Engine Air Cleaner Filter Selection Refer to the “Maintenance Schedule” for the proper The quality of replacement engine air cleaner filters maintenance intervals. varies considerably. Only high quality filters should be used to assure most efficient service. MOPAR engine air NOTE: Be sure to follow the “Sever Duty Conditions” cleaner filters are a high quality filter and are recommaintenance interval if applicable. mended.
600 MAINTAINING YOUR VEHICLE WARNING! (Continued) CAUTION! splashes in eyes or on skin, flush the area immediately with large amounts of water. Refer to “Jump-Starting Procedures” in “What To Do In Emergencies” for further information. • Battery gas is flammable and explosive. Keep flame or sparks away from the battery. Do not use a booster battery or any other booster source with an output greater than 12 Volts. Do not allow cable clamps to touch each other.
MAINTAINING YOUR VEHICLE 601 Air Conditioner Maintenance WARNING! (Continued) For best possible performance, your air conditioner should be checked and serviced by an authorized dealer at the start of each warm season. This service should include cleaning of the condenser fins and a performance test. Drive belt tension should also be checked at this time. • The air conditioning system contains refrigerant under high pressure.
602 MAINTAINING YOUR VEHICLE manufacturer recommends that air conditioning service 2. Pull the console closeout cover rearward to disengage be performed by authorized dealer using recovery and the front retaining tab and remove the cover. recycling equipment. NOTE: Use only manufacturer approved A/C system PAG compressor oil, and refrigerants. A/C Air Filter WARNING! Do not remove the A/C air filter while the blower is operating or personal injury may result.
MAINTAINING YOUR VEHICLE 603 7 Hush Panel Air Filter Cover Location 4. Remove the filter door by pushing down the tab on the 5. Remove the A/C air filter by pulling it straight out of top bottom of the door and lift the tab at the top of the the housing. Take note of the air filter position flow door to release the cover then rotate remove the door direction indicators. out and lift up.
604 MAINTAINING YOUR VEHICLE CAUTION! The A/C air filter is identified with an arrow to indicate airflow direction through the filter. Failure to properly install the filter will result in the need to replace it more often. 7. Install the passenger side hush panel under the dash panel and console closeout. Refer to the “Maintenance Schedule” for the proper maintenance intervals. A/C Air Filter 6. Install the A/C air filter with the air filter position indicators pointing in the same direction as removal.
MAINTAINING YOUR VEHICLE 605 Body Lubrication Windshield Wiper Blades Locks and all body pivot points, including such items as seat tracks, door hinge pivot points and rollers, liftgate, tailgate, decklid, sliding doors and hood hinges, should be lubricated periodically with a lithium based grease, such as MOPAR Spray White Lube to assure quiet, easy operation and to protect against rust and wear.
606 MAINTAINING YOUR VEHICLE Adding Washer Fluid The fluid reservoir is located in the front of the engine compartment. Be sure to check the fluid level in the reservoir at regular intervals. Fill the reservoir with windshield washer solvent (not radiator antifreeze) and operate the system for a few seconds to flush out the residual water. WARNING! Commercially available windshield washer solvents are flammable. They could ignite and burn you.
MAINTAINING YOUR VEHICLE 607 exhaust system inspected each time the vehicle is raised for lubrication or oil change. Replace as required. WARNING! • Exhaust gases can injure or kill. They contain carbon monoxide (CO), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing CO, refer to “Safety Tips/Exhaust Gas” in “Things To Know Before Starting Your Vehicle” for further information.
608 MAINTAINING YOUR VEHICLE Under normal operating conditions, the catalytic con- To minimize the possibility of catalytic converter damverter will not require maintenance. However, it is im- age: portant to keep the engine properly tuned to assure • Do not shut off the engine or interrupt the ignition, proper catalyst operation and prevent possible catalyst when the transmission is in gear and the vehicle is in damage. motion.
MAINTAINING YOUR VEHICLE 609 Cooling System WARNING! You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator. If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool. Never try to open a cooling system pressure cap when the radiator or coolant bottle is hot. Engine Coolant Checks Check the engine coolant (antifreeze) protection every 12 months (before the onset of freezing weather, where applicable).
610 MAINTAINING YOUR VEHICLE Cooling System — Drain, Flush And Refill NOTE: Some vehicles require special tools to add coolant properly. Failure to fill these systems properly could lead to severe internal engine damage. If any coolant is needed to be added to the system please contact your local authorized dealer. If the engine coolant (antifreeze) is dirty or contains visible sediment, have an authorized dealer clean and flush with OAT coolant (antifreeze) (conforming to MS.90032).
MAINTAINING YOUR VEHICLE 611 CAUTION! (Continued) rust inhibitors or antirust products, as they may not be compatible with the radiator engine coolant and may plug the radiator. • This vehicle has not been designed for use with propylene glycol-based engine coolant (antifreeze). Use of propylene glycol-based engine coolant (antifreeze) is not recommended.
612 MAINTAINING YOUR VEHICLE Please note that it is the owner’s responsibility to maintain the proper level of protection against freezing according to the temperatures occurring in the area where the vehicle is operated. NOTE: Cooling System Pressure Cap The cap must be fully tightened to prevent loss of engine coolant (antifreeze), and to ensure that engine coolant (antifreeze) will return to the radiator from the coolant recovery tank.
MAINTAINING YOUR VEHICLE 613 WARNING! (Continued) • Do not use a pressure cap other than the one specified for your vehicle. Personal injury or engine damage may result. Disposal Of Used Engine Coolant Used ethylene glycol-based engine coolant (antifreeze) is a regulated substance requiring proper disposal. Check with your local authorities to determine the disposal rules for your community.
614 MAINTAINING YOUR VEHICLE • If frequent engine coolant (antifreeze) additions are required, the cooling system should be pressure tested NOTE: When the vehicle is stopped after a few miles/ for leaks. kilometers of operation, you may observe vapor coming from the front of the engine compartment. This is nor- • Maintain engine coolant (antifreeze) concentration at a minimum of 50% OAT coolant (conforming to mally a result of moisture from rain, snow, or high MS.
MAINTAINING YOUR VEHICLE 615 Be sure to clean the top of the master cylinder area before removing the cap. If necessary, add fluid to bring the In order to assure brake system performance, all brake fluid level up to the requirements described on the brake system components should be inspected periodically. fluid reservoir. With disc brakes, fluid level can be Refer to the “Maintenance Schedule” for the proper expected to fall as the brake pads wear. Brake fluid level maintenance intervals.
616 MAINTAINING YOUR VEHICLE WARNING! (Continued) WARNING! (Continued) can severely damage your brake system and/or impair its performance. The proper type of brake fluid for your vehicle is also identified on the original factory installed hydraulic master cylinder reservoir. • To avoid contamination from foreign matter or moisture, use only new brake fluid or fluid that has been in a tightly closed container. Keep the master cylinder reservoir cap secured at all times.
MAINTAINING YOUR VEHICLE 617 NOTE: No chemical flushes should be used in any transmission. Avoid using transmission sealers as they transmission; only the approved lubricant should be may adversely affect seals. used. CAUTION! CAUTION! Using a transmission fluid other than the manufacturer’s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder. Refer to “Fluids, Lubricants, And Genuine Parts” in this section for fluid specifications.
618 MAINTAINING YOUR VEHICLE the transmission fluid level checked. Operating the ve- Appearance Care And Protection From Corrosion hicle with an improper fluid level can cause severe Protection Of Body And Paint From Corrosion transmission damage. Vehicle body care requirements vary according to geographic locations and usage.
MAINTAINING YOUR VEHICLE 619 • If insects, tar, or other similar deposits have accumulated on your vehicle, use MOPAR Super Kleen Bug Corrosion is the result of deterioration or removal of and Tar Remover to remove. paint and protective coatings from your vehicle. • Use a high quality cleaner wax, such as MOPAR The most common causes are: Cleaner Wax to remove road film, stains and to protect • Road salt, dirt and moisture accumulation. your paint finish. Take care never to scratch the paint.
620 MAINTAINING YOUR VEHICLE • If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials are well • If you drive on salted or dusty roads or if you drive packaged and sealed. near the ocean, hose off the undercarriage at least once a month. • If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel.
MAINTAINING YOUR VEHICLE 621 NOTE: If your vehicle is equipped with Dark Vapor or Black Satin Chrome wheels DO NOT USE wheel cleaners, abrasives or polishing compounds. They will permanently damage this finish and such damage is not covered by the New Vehicle Limited Warranty. USE ONLY MILD SOAP AND WATER WITH A SOFT CLOTH. Used on a regular basis this is all that is required to maintain this finish. CAUTION! Do not use scouring pads, steel wool, a bristle brush, or metal polishes.
622 MAINTAINING YOUR VEHICLE Interior Care Use MOPAR Total Clean to clean fabric upholstery and carpeting. Use MOPAR Total Clean to clean vinyl upholstery. MOPAR Total Clean is specifically recommended for leather upholstery. Your leather upholstery can be best preserved by regular cleaning with a damp soft cloth. Small particles of dirt can act as an abrasive and damage the leather upholstery and should be removed promptly with a damp cloth.
MAINTAINING YOUR VEHICLE 623 CAUTION! Do not use Alcohol and Alcohol-based and/or Keton based cleaning products to clean leather seats, as damage to the seat may result. Do not use abrasive cleaning components, solvents, steel wool or other aggressive material to clean the lenses. Glass Surfaces All glass surfaces should be cleaned on a regular basis with MOPAR Glass Cleaner, or any commercial Cleaning Headlights household-type glass cleaner.
624 MAINTAINING YOUR VEHICLE If the belts need cleaning, use a mild soap solution or lukewarm water. Do not remove the belts from the The lenses in front of the instruments in this vehicle are vehicle to wash them. Dry with a soft cloth. molded in clear plastic. When cleaning the lenses, care must be taken to avoid scratching the plastic. Replace the belts if they appear frayed or worn or if the buckles do not work properly. 1. Clean with a wet soft cloth.
MAINTAINING YOUR VEHICLE 625 FUSES WARNING! (Continued) WARNING! • When replacing a blown fuse, always use an appropriate replacement fuse with the same amp rating as the original fuse. Never replace a fuse with another fuse of higher amp rating. Never replace a blown fuse with metal wires or any other material. Failure to use proper fuses may result in serious personal injury, fire and/or property damage.
626 MAINTAINING YOUR VEHICLE Power Distribution Center (Fuses) The Power Distribution Center is located in the engine compartment near the battery. This center contains cartridge fuses, mini-fuses, micro-fuses, circuit breakers and relays. A label that identifies each component is printed on the inside of the cover. Power Distribution Center Cavity F06 F07 F08 F09 Cartridge Fuse – – – – Blade Fuse – – 25 Amp Clear – Description Not Used Not Used Engine Control Module (ECM)/Fuel Inj.
MAINTAINING YOUR VEHICLE 627 Cavity F10 Cartridge Fuse – Blade Fuse 20 Amp Yellow F11 F12 F13 – – – – 20 Amp Yellow 10 Amp Red F14 – 10 Amp Red F15 F16 F17 F18 F19 – – – – 40 Amp Green – 20 Amp Yellow – – – Description Power Transfer Unit (PTU) – If Equipped Not Used Brake Vacuum Pump – If Equipped Engine Control Module (ECM)/VSM (Engine Stop/Start Only) Drivetrain Control Module (DTCM)/ Power Transfer Unit (PTU) – If Equipped/RDM/Brake System Module (BSM)/Brake Pedal Switch/EPB (Electric Park
628 MAINTAINING YOUR VEHICLE Cavity F20 F21 F22 F23 Cartridge Fuse – – – – Blade Fuse 10 Amp Red – 5 Amp Tan 70 Amp Tan F23 – 50 Amp Red F24 F25B – – – 20 Amp Yellow F26 F27 F28 F29 – – – – – – 15 Amp Blue – Description A/C Compressor Clutch Not Used Radiator Fan Enable Body Controller Module (BCM) – Feed 2 Voltage Stability Module (VSM) #2 – If Equipped With Engine Stop/Start Option Not Used Front Washer Pump – If Equipped with Engine Stop/Start Option Not Used Not Used Transmission Control Mo
MAINTAINING YOUR VEHICLE 629 Cavity F30 Cartridge Fuse – Blade Fuse 10 Amp Red F31 F32 F33 F34 F35 F36 F37 F38 F39 F40 F41 – – – – – – 50 Amp Red – 40 Amp Green – 50 Amp Red – – – – – – – – – – – Description Engine Control Module (ECM)/EPS/ Fuel Pump Relay Feed Not Used Not Used Not Used Not Used Not Used Not Used Radiator Fan PWM Controller Not Used HVAC Blower Motor Not Used Voltage Stability Module (VSM) #1 – If Equipped With Engine Stop/Start Option 7
630 MAINTAINING YOUR VEHICLE Cavity F41 Cartridge Fuse 60 Amp Yellow Blade Fuse — F42 F43 F44 F45 – – – 30 Amp Pink – 20 Amp Yellow – – F46 F47 F48 F49 25 Amp Clear – 30 Amp Pink 30 Amp Pink – – – – F50 30 Amp Pink – F51 – – Description Body Controller Module (BCM) – Feed 1 Not Used Fuel Pump Motor Not Used Passenger Door Module (PDM) – If Equipped Sunroof – If Equipped Not Used Driver Door Module (DDM) Power Inverter (115V A/C) – If Equipped Windshield Wiper Smart Motor (WWSM) Not Used
MAINTAINING YOUR VEHICLE 631 Cavity F52 F53 F54 Cartridge Fuse – 30 Amp Pink 30 Amp Pink Blade Fuse – – – F55 – 10 Amp Red F56 F57 F58 – – – 15 Amp Blue – 10 Amp Red F59 F60 F61 30 Amp Pink – – – 20 Amp Yellow – Description Not Used Brake System Module BSM & Valves Body Controller Module (BCM) – Feed 3 Blind Spot Sensors/Compass/Rearview Camera – If Equipped Ignition Node Module (IGNM)/RF Hub Not Used Occupant Classification Module/Voltage Stability Module (VSM) #2 – If Equipped With Engine Sto
632 MAINTAINING YOUR VEHICLE Cavity F62 F63 F64 F65 Cartridge Fuse – – – – Blade Fuse – 20 Amp Yellow 20 Amp Yellow 10 Amp Red F66 – 15 Amp Blue F67 – 10 Amp Red F68 – – Description Not Used Front Heated Seats – If Equipped Heated Steering Wheel – If Equipped In Vehicle Temperature Sensor/ Humidity Sensor/Driver Assist System Module (DASM)/Park Assist (PAM) – If Equipped With Engine Stop/Start Option Instrument Panel Cluster (IPC)/ Electronic Climate Control (ECC) In Vehicle Temperature Sensor/
MAINTAINING YOUR VEHICLE 633 Cavity F69 Cartridge Fuse – Blade Fuse 10 Amp Red F70 – 5 Amp Tan F71 – 20 Amp Yellow F72 F73 F74 F75 F76 F77 F78 – – 30 Amp Pink – – – – 10 Amp Red – – 20 Amp Yellow 10 Amp Red 10 Amp Red 10 Amp Red Description Gear Shift Module (GSM)/Active Grill Shutter (AGS).
634 MAINTAINING YOUR VEHICLE Cavity F79 Cartridge Fuse – Blade Fuse 10 Amp Red F80 F81 F82 F83 F84 F85 F86 – – – 20 Amp Blue 30 Amp Pink – – 20 Amp Yellow – – – – – 20 Amp Yellow F87A – 20 Amp Yellow Description Integrated Center Stack (ICS)/Switch Bank/Instrument Panel Cluster (IPC)/ EPB SW Radio Not Used Not Used Engine Control Module (ECM) Electric Park Brake (EPB) – Left Not Used Horns – If Equipped With Engine Stop/ Start Option HID Headlamp Left – If Equipped Engine Stop/Start Option
MAINTAINING YOUR VEHICLE 635 Cavity F88 Cartridge Fuse – Blade Fuse 10 Amp Red F89 F90 F91 F92 F93 – – – – 40 Amp Green – – – – – F94 F95 30 Amp Pink – – 10 Amp Red Description Collision Mitigation Module (CMM)/ Electrochromatic Mirror/Haptic Lane Feedback Module (Half)/Humidity Sensor– If Equipped Not Used Not Used Not Used Not Used Brake System Module (BSM) – Pump Motor – If Equipped Electric Park Brake (EPB) – Right Electrochromatic Mirror/Rain/Pass.
636 MAINTAINING YOUR VEHICLE Cavity F96 Cartridge Fuse – Blade Fuse 10 Amp Red F97 – 10 Amp Red F98 F99 F100 – – – 25 Amp Clear – – Description Occupant Restraint Controller (ORC) (Airbag) Occupant Restraint Controller (ORC) (Airbag) Audio Amplifier – If Equipped Not Used Not Used
MAINTAINING YOUR VEHICLE 637 Interior Fuses The interior fuse panel is located in the passenger compartment on the left side dash panel under the instrument panel. Cavity F13 F32 F36 F37 F38 F43 F48 F49 F51 Blade Fuse 15 Amp Blue 10 Amp Red 10 Amp Red 7.5 Amp Brown 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow 7.5 Amp Brown 10 Amp Red Description Low Beam Left Interior Lighting Intrusion Module / Siren Aux.
638 MAINTAINING YOUR VEHICLE Cavity F53 F89 F91 F92 F93 Blade Fuse 7.5 Amp Brown 5 Amp Tan 5 Amp Tan 5 Amp Tan 10 Amp Red Description UCI Port (USB & AUX) Trunk Lamp Fog Lamp Front Left Fog Lamp Front Right Low Beam Right • Anytime you store your vehicle, or keep it out of service (i.e. vacation) for two weeks or more, run the If you are leaving your vehicle dormant for more than 21 air conditioning system at idle for about five minutes days you may want to take steps to protect your battery.
MAINTAINING YOUR VEHICLE 639 REPLACEMENT BULBS Interior Bulbs Front Courtesy/Reading Lamp Center Courtesy/Reading Lamp Visor Vanity Lamp Glove Compartment Lamp Shift Indicator Lamp Rear Compartment (Trunk) Lamp NOTE: For lighted switches, see your authorized dealer for replacement.
640 MAINTAINING YOUR VEHICLE Exterior Bulbs High Intensity Discharge Headlamp Bi-Halogen Headlamp Daytime Running Lamp Front Turn Signal Lamp Side Marker Lamp Front Park Lamp Front Fog Lamp LED Front Fog Lamp Center High Mounted Stop (CHMSL) Lamp Stop/Turn Signal Lamp Rear Tail/Side Marker Lamp Backup Lamp License Lamp Bulb Number HID (Serviced at Authorized Dealer) 9005HL+ LED (Serviced at Authorized Dealer) PWY24W SV W3W LED (Serviced at Authorized Dealer) H11 LED (Serviced at Authorized Dealer) LED (Se
MAINTAINING YOUR VEHICLE 641 NOTE: On vehicles equipped with HID headlamps, when the headlamps are turned on, there is a blue hue to NOTE: Lens fogging can occur under certain atmothe lights. This diminishes and becomes more white after spheric conditions. This will usually clear as atmospheric approximately 10 seconds, as the system charges. conditions change to allow the condensation to change back into a vapor. Turning the lamps on will usually WARNING! accelerate the clearing process.
642 MAINTAINING YOUR VEHICLE Access Door Headlamp Bulb Cap 2. Reach behind the headlamp housing to access the 4. Firmly grasp the headlamp bulb socket assembly and headlamp bulb cap. rotate counterclockwise to remove from the housing. 3. Firmly grasp the headlamp bulb cap and rotate it counterclockwise to unlock it.
MAINTAINING YOUR VEHICLE 643 7 Headlamp Bulb Socket Headlamp Bulb 5. Disconnect the bulb from the electrical connector and then connect the replacement bulb. CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol.
644 MAINTAINING YOUR VEHICLE 6. Install the bulb and connector assembly into the headlamp housing and rotate clockwise to lock it in place. 7. Install the headlamp bulb cap in the headlamp housing and rotate clockwise to lock it in place. 8. Lock headlamp access door in wheel liner. Front Turn Signal Lamp 1. Open the hood. NOTE: Removal of the air cleaner filter housing may be necessary prior to replacing bulbs in the lamp assembly on the passenger side of the vehicle. Beauty Cover 3.
MAINTAINING YOUR VEHICLE 645 7. Install air cleaner filter housing, if removed. 8. Install brace, brace bolts and tighten as shown. 7 Front Turn Signal Lamp Socket 5. Pull the bulb out of the socket and insert the replacement bulb. Brace Bolt Tightening Sequence 6. Install the front turn signal lamp socket assembly into 9. Install beauty cover. the housing, and rotate the front turn signal lamp socket clockwise to lock it in place.
646 MAINTAINING YOUR VEHICLE Front Side Marker Lamps 1. Remove the three fasteners from the inner wheel liner and carefully peel back liner for access. Front Side Marker Lamp Bulb Removal 3. Remove bulb from the front side marker lamp socket and replace with a new bulb. 4. Install front side marker lamp socket in lamp assembly and rotate 1/4 turn clockwise to lock into place. 2. Firmly grasp the front side marker lamp socket and rotate 1/4 turn counterclockwise to remove it from the 5.
MAINTAINING YOUR VEHICLE 647 3. Rotate the front fog lamp socket counterclockwise, and remove the bulb and socket assembly from the 1. Remove the three fasteners from the lower closeout, front fog lamp housing. and peel down the lower closeout. Front Fog Lamp 7 Lower Closeout 2. Reach behind the fog lamp housing to access the bulb. Front Fog Lamp Socket 4. Pull the bulb out of the socket and insert the replacement bulb.
648 MAINTAINING YOUR VEHICLE CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol. Backup Lamps (Passenger Side) 1. Open trunk lid. 2. Remove the passenger side access cover. 3. Remove the inner trunk lid handle cover. 4. Remove the two screws and remove the inner trunk 5. Install the front fog lamp socket assembly into the into lid handle.
MAINTAINING YOUR VEHICLE 649 7 Inner Deck Panel Backup Lamp Socket 6. Rotate the backup lamp socket counter clockwise 1/4 7. Remove the bulb from the socket and install the turn to remove the backup lamp socket from the trunk replacement bulb. lid lamp housing. 8. Install the backup lamp socket into the trunk lid lamp housing.
650 MAINTAINING YOUR VEHICLE 9. Rotate backup lamp socket clockwise 1/4 turn to lock it into place. 10. Reposition the inner deck panel and secure with a push pin if removed. 11. Install access cover. Backup Lamps (Driver Side) 1. Open trunk lid. 2. Remove the drivers side access cover. 3. Remove inner deck lid support push pin. Backup Lamp Socket NOTE: If necessary remove any additional inner deck lid 5. Rotate the backup lamp socket counter clockwise 1/4 trim push pins to gain access.
MAINTAINING YOUR VEHICLE 651 7. Install the backup lamp socket into the trunk lid lamp housing. 8. Rotate backup lamp socket clockwise 1/4 turn to lock it into place. 9. Reposition the inner deck panel and secure with a push pin if removed. 10. Install the access cover. Stop/Rear Turn Signal Lamp 1. Open the trunk lid. Tail Lamp Beauty Cover 2. Remove the tail lamp housing beauty cover by grasping the top edge and pulling rearward to expose the 3. Remove the tail lamp housing bolts tail lamp housing bolts.
652 MAINTAINING YOUR VEHICLE 5. Rotate the stop/rear turn signal lamp socket 1/4 turn counterclockwise and remove it from the tail lamp housing. 6. Remove the bulb from the socket and install the replacement bulb. 7. Install the bulb socket into the tail lamp housing and rotate the bulb socket ¼ turn clockwise to lock it in place. 8. Install the tail lamp housing. 9. Install the tail lamp housing beauty cover. Tail Lamp Bolts License Plate Lamp 4. Pull the tail lamp housing directly rearward to dis- 1.
MAINTAINING YOUR VEHICLE 653 FLUID CAPACITIES Fuel (Approximate) 2.4L and 3.6L Engines Engine Oil With Filter 2.4 Liter Engine (SAE 0W-20, API Certified) 3.6 Liter Engine (SAE 5W-20, API Certified) Cooling System* 2.4 Liter Engine (MOPAR Antifreeze/Engine Coolant 10 Year/150,000 Mile Formula) 3.6 Liter Engine (MOPAR Antifreeze/Engine Coolant 10 Year/150,000 Mile Formula) * Includes heater and coolant reservoir filled to MAX level. U.S. Metric 15.8 Gallons 60 Liters 5.5 Quarts 6 Quarts 5.2 Liters 5.
654 MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS, AND GENUINE PARTS Engine Component Engine Coolant Engine Oil – 2.4L Engine Engine Oil – 3.6L Engine Fluid, Lubricant, or Genuine Part We recommend you use MOPAR Antifreeze/Coolant 10 Year/150,000 Mile Formula OAT (Organic Additive Technology) or equivalent meeting the requirements of FCA Material Standard MS.90032.
MAINTAINING YOUR VEHICLE 655 Component Engine Oil Filter Spark Plugs Fuel Selection – 2.4L Engine Fuel Selection – 2.4L Flex Fuel (E85) Engine – If Equipped Fuel Selection – 3.6L Engine Fuel Selection – 3.6L Flex Fuel (E85) Engine – If Equipped Fluid, Lubricant, or Genuine Part We recommend you use a MOPAR Engine Oil Filter. We recommend you use MOPAR Spark Plugs. 87 Octane, 0-15% Ethanol. 87 Octane, Up To 85% Ethanol. 87 Octane, 0-15% Ethanol. 87 Octane, Up To 85% Ethanol.
656 MAINTAINING YOUR VEHICLE CAUTION! CAUTION! (Continued) • Mixing of engine coolant (antifreeze) other than specified Organic Additive Technology (OAT) engine coolant (antifreeze), may result in engine damage and may decrease corrosion protection. Organic Additive Technology (OAT) engine coolant is different and should not be mixed with Hybrid Organic Additive Technology (HOAT) engine coolant (antifreeze) or any “globally compatible” coolant (antifreeze).
MAINTAINING YOUR VEHICLE 657 Chassis Component Automatic Transmission Brake Master Cylinder Fluid, Lubricant, or Genuine Part Use only MOPAR ZF 8&9 Speed ATF Automatic Transmission Fluid, or equivalent. Failure to use the correct fluid may affect the function or performance of your transmission. We recommend you use MOPAR DOT 3 Brake Fluid, SAE J1703 should be used. If DOT 3, SAE J1703 brake fluid is not available, then DOT 4 is acceptable. Use only recommended brake fluids.
MAINTENANCE SCHEDULES CONTENTS 䡵 MAINTENANCE SCHEDULE . . . . . . . . . . . . .660 ▫ Maintenance Chart . . . . . . . . . . . . . . . . . . . .
660 MAINTENANCE SCHEDULES than your authorized dealer, the message can be reset by referring to the steps described under “Oil Change Reset” Your vehicle is equipped with an automatic oil change in “Electronic Vehicle Information Center (EVIC)” or indicator system. The oil change indicator system will ⬙Driver Information Display (DID)” in “Understanding remind you that it is time to take your vehicle in for Your Instrument Panel” for further information. scheduled maintenance.
MAINTENANCE SCHEDULES 661 Once A Month Or Before A Long Trip: • Check engine oil level. • Check windshield washer fluid level. • Check tire pressure and look for unusual wear or damage. Rotate tires at the first sign of irregular wear, even if it occurs before the oil indicator system turns on. • Check the fluid levels of the coolant reservoir and brake master cylinder, fill as needed. • Check function of all interior and exterior lights.
662 MAINTENANCE SCHEDULES Mileage: 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 110,000 120,000 130,000 140,000 150,000 Or Years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Or Kilometers: 32,000 48,000 64,000 80,000 96,000 112,000 128,000 144,000 160,000 176,000 192,000 208,000 224,000 240,000 Maintenance Chart Additional Inspections Inspect the CV joints. Inspect front suspension, boot seals, tie rod ends, and replace if necessary.
Mileage: 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 110,000 120,000 130,000 140,000 150,000 Or Years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Or Kilometers: 32,000 48,000 64,000 80,000 96,000 112,000 128,000 144,000 160,000 176,000 192,000 208,000 224,000 240,000 MAINTENANCE SCHEDULES 663 Replace spark plugs ** Flush and replace the engine coolant at 10 years or 150,000 miles (240,000 km) whichever comes first.
664 MAINTENANCE SCHEDULES WARNING! (Continued) you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic. • Failure to properly inspect and maintain your vehicle could result in a component malfunction and effect vehicle handling and performance. This could cause an accident.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS 䡵 SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . .667 ▫ Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY). . . . . . . . . . . . . . . . . . .669 ▫ Prepare For The Appointment. . . . . . . . . . . . .667 ▫ Service Contract . . . . . . . . . . . . . . . . . . . . . .669 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . . .667 䡵 WARRANTY INFORMATION . . . . . . . . . . . . .
666 IF YOU NEED CONSUMER ASSISTANCE 䡵 DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES . . . . . . . . . . . . . . . . .673 ▫ Treadwear. . . . . . . . . . . . . . . . . . . . . . . . . . .673 ▫ Traction Grades . . . . . . . . . . . . . . . . . . . . . . .674 ▫ Temperature Grades. . . . . . . . . . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE 667 SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment Be Reasonable With Requests If you list a number of items and you must have your vehicle by the end of the day, discuss the situation with the service advisor and list the items in order of priority. At many authorized dealers, you may obtain a rental vehicle at a minimal daily charge. If you need a rental, it is advisable to make these arrangements when you call for an appointment.
668 IF YOU NEED CONSUMER ASSISTANCE facilities, factory-trained technicians, special tools, and • Authorized dealer name the latest information to ensure the vehicle is fixed • Vehicle Identification Number (VIN) correctly and in a timely manner. • Vehicle delivery date and mileage This is why you should always talk to an authorized dealer service manager first. Most matters can be re- FCA US LLC Customer Center solved with this process. P.O.
IF YOU NEED CONSUMER ASSISTANCE 669 In Mexico Contact Av. Prolongacion Paseo de la Reforma, 1240 Sante Fe C.P. 05109 Mexico, D. F. In Mexico City: 5081-7568 Outside Mexico City: 1-800-505-1300 Puerto Rico And U.S. Virgin Islands Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommunication Devices for the Deaf) equipment at its customer center.
670 IF YOU NEED CONSUMER ASSISTANCE Warranty expires. The manufacturer stands behind only the manufacturer’s service contracts. If you purchased a manufacturer’s service contract, you will receive Plan Provisions and an Owner Identification Card in the mail within three weeks of the vehicle delivery date.
IF YOU NEED CONSUMER ASSISTANCE 671 If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in See the Warranty Information Booklet, located on the a group of vehicles, it may order a recall and remedy DVD, for the terms and provisions of FCA US LLC campaign. However, NHTSA cannot become involved in warranties applicable to this vehicle and market. individual problems between you, your authorized dealer, and the manufacturer.
672 IF YOU NEED CONSUMER ASSISTANCE In Canada Service Manuals If you believe that your vehicle has a safety defect, you should contact the Customer Service Department immediately. Canadian customers who wish to report a safety defect to the Canadian government should contact Transport Canada, Motor Vehicle Defect Investigations and Recalls at 1-800-333-0510 or go to http://www.tc.gc.
IF YOU NEED CONSUMER ASSISTANCE 673 Owner’s Manuals These Owner’s Manuals have been prepared with the assistance of service and engineering specialists to acquaint you with specific FCA US LLC vehicles. Included are starting, operating, emergency and maintenance procedures as well as specifications, capabilities and safety tips. Call toll free at: • 1-800-890-4038 (U.S.) • 1-800-387-1143 (Canada) Or Visit us on the Worldwide Web at: • www.techauthority.
674 IF YOU NEED CONSUMER ASSISTANCE significantly from the norm due to variations in driving Temperature Grades habits, service practices, and differences in road charac- The temperature grades are A (the highest), B, and C, teristics and climate. representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under Traction Grades controlled conditions on a specified indoor laboratory The Traction grades, from highest to lowest, are AA, A, B, test wheel.
IF YOU NEED CONSUMER ASSISTANCE 675 WARNING! The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, under-inflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure.
INDEX 10
678 INDEX About Your Brakes . . . . . . . . . . . . . . . . . . . . . . . .474 Adaptive Cruise Control (ACC) (Cruise Control) . . .182 Adding Engine Coolant (Antifreeze) . . . . . . . . . . . .611 Additives, Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . .527 Adjust Down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .141 Forward . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .141 Rearward . . . . . . . . . . . . . . . . . . . . . . . . . . . . .141 Up . . . . . . . . . .
INDEX 679 Alarm Arm The System . . . . . . . . . . . . . . . . . . . . . . . .19 Disarm The System . . . . . . . . . . . . . . . . . . . . . . .20 Rearming The System . . . . . . . . . . . . . . . . . . . . .19 Tamper Alert . . . . . . . . . . . . . . . . . . . . . . . . . . .21 Vehicle Security Alarm . . . . . . . . . . . . . . . . . . . .19 Alarm, Panic . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 Alarm (Security Alarm) . . . . . . . . . . . . . . . . . . . . .325 All Wheel Drive (AWD). .
680 INDEX Caps, Filler Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .532 Oil (Engine) . . . . . . . . . . . . . . . . . . . .589, 590, 597 Radiator (Coolant Pressure) . . . . . . . . . . . . . . . .612 Carbon Monoxide Warning . . . . . . . . . . . . . . .109, 528 Cargo Area Features . . . . . . . . . . . . . . . . . . . . . . .304 Cargo Compartment . . . . . . . . . . . . . . . . . . . . . . .304 Car Washes . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 681 Child Restraints . . . . . . . . . . . . . . . . . . . . . . . . .86 Child Seat Installation . . . . . . . . . . . . . . . . .102, 104 How To Stow An Unused ALR Seat Belt . . . . . . .101 Infants And Child Restraints . . . . . . . . . . . . . . . .88 Install A LATCH-Compatible Child Restraint . . . .99 Installing Child Restraints Using The Vehicle Seat Belt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102 LATCH Positions . . . . . . . . . . . . . . . . . . . . . . . .
682 INDEX Cruise Light . . . . . . . . . . . . . . . . . . . . . .348, 349, 350 Door Ajar. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .332 Cupholders . . . . . . . . . . . . . . . . . . . . . . . . . . . . .297 Door Ajar Light . . . . . . . . . . . . . . . . . . . . . . . . . .332 Customer Assistance . . . . . . . . . . . . . . . . . . . . . . .667 Door Locks Child-Protection Door Lock — Rear Doors . . . . . .34 Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 683 Driver’s Seat Back Tilt . . . . . . . . . . . . . . . . . . . . . .145 Driving Through Flowing, Rising, Or Shallow Standing Water . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .465 E-85 Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .529 Electrical Power Outlets. . . . . . . . . . . . . . . . . . . . .293 Electric Parking Brake . . . . . . . . . . . . . . . . . . . . . .468 Electric Rear Window Defrost. . . . . . . . . . . . . . . . .308 Electric Remote Mirrors .
684 INDEX Coolant (Antifreeze) . . . . . . . . . . . . . . . . . . . . .654 Cooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .609 Exhaust Gas Caution . . . . . . . . . . . . . . . . .109, 528 Fails To Start . . . . . . . . . . . . . . . . . . . . . . . . . .449 Flooded, Starting . . . . . . . . . . . . . . . . . . . . . . .449 Fuel Requirements . . . . . . . . . . . . . . . . . . . . . .524 Jump Starting . . . . . . . . . . . . . . . . . . . . . . . . . .572 Oil . . . . . . . . . . . . . .
INDEX 685 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . .532 Replacement Parts . . . . . . . . . . . . . . . . . . . . . . .531 Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .531 Flooded Engine Starting . . . . . . . . . . . . . . . . . . . .449 Floor Console . . . . . . . . . . . . . . . . . . . . . . . . . . . .300 Fluid, Brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . .657 Fluid Capacities . . . . . . . . . . . . . . . . . . . . . . . . . .
686 INDEX Time Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . .160 Gear Ranges . . . . . . . . . . . . . . . . . . . . . . . . . . . . .455 Glass Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . .623 Head Restraints . . . . . . . . . . . . . . . . . . . . . . . . . .148 GVWR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .536 Head Rests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .148 Heated Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 687 Panic Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 Instrument Cluster . . . . . . . .315, 318, 326, 331, 343, 347 Programming Additional Key Fobs . . . . . . . . .18, 25 Instrument Cluster . . . . . . . . . . . . . . . . . . .354, 366 Programming Additional Transmitters . . . . . . .18, 25 Instrument Panel And Controls . . . . . . . . . . . . . . .314 Remote Battery Replacement . . . . . . . . . . . . . . . .25 Instrument Panel Lens Cleaning . . . . . . . . . . . . . . .
688 INDEX Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 Lane Change And Turn Signals . . . . . . . . . . . . . . .165 Lane Change Assist . . . . . . . . . . . . . . . . . . . . . . . .165 LaneSense . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .214 Lap/Shoulder Belts. . . . . . . . . . . . . . . . . . . . . . . . .50 Latches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112 Lead Free Gasoline . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 689 Lights On Reminder . . . . . . . . . . . . . . . . . . . . .163 Low Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .340 Malfunction Indicator (Check Engine) . . . . . . . . .333 Parade Mode (Daytime Brightness) . . . . . . . . . . .169 Park . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .346 Passing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .165 Reading . . . . . . . . . . . . . . . . . . . . . . . . . . .166, 272 Seat Belt Reminder . . . . . . . . . .
690 INDEX Memory Seats And Radio . . . . . . . . . . . . . . . . . . .153 Octane Rating, Gasoline (Fuel). . . . . . . . . . . . .524, 654 Methanol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .525 Oil, Engine . . . . . . . . . . . . . . . . . . . . . . . . . .595, 654 Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . .653 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .120 Change Interval . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 691 Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . .33 Opener, Garage Door (HomeLink) . . . . . . . . . . . . .274 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .129 Operating Precautions . . . . . . . . . . . . . . . . . . . . . .591 Outlet (Auxiliary Electrical Outlet) . . . . . . . .293, 296 Operator Manual (Owner’s Manual) . . . . . . . . . . . . .4 Sunroof . . . . . . . . . . . . . . . . . . . . . . . . . . .284, 288 Outside Rearview Mirrors . . . . . . . .
692 INDEX Radio Operation . . . . . . . . . . . . . . . . . . . . . . . . . .396 Remote Keyless Entry (RKE) Radio Remote Controls . . . . . . . . . . . . . . . . . . . . .395 Lock The Doors . . . . . . . . . . . . . . . . . . . . . . . . .24 Panic Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 Radio (Sound Systems) . . . . . . . . . . . . . . . . . . . . .394 Programming Additional Key Fobs . . . . . . . . .18, 25 Rain Sensitive Wiper System . . . . . . . . . . . . . . . . .
INDEX 693 Remote Starting System. . . . . . . . . . . . . . . . . . . . . .27 Seat Belt Remote Trunk Release. . . . . . . . . . . . . . . . . . . . . . .45 Adjustable Upper Shoulder Belt Anchorage . . . . . .55 Automatic Locking Retractor (ALR) . . . . . . . . . . .58 Replacement Bulbs . . . . . . . . . . . . . . . . . . . . . . . .639 Energy Management Feature . . . . . . . . . . . . . . . .58 Replacement Parts. . . . . . . . . . . . . . . . . . . . . . . . .593 Lap/Shoulder Belt Operation . . . . . . . .
694 INDEX Front Seat . . . . . . . . . . . . . . . . . . . . . . . .48, 50, 53 Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . .110 Operating Instructions . . . . . . . . . . . . . . . . . . . .53 Pregnant Women . . . . . . . . . . . . . . . . . . . . . . . .57 Pretensioners . . . . . . . . . . . . . . . . . . . . . . . . . . .58 Rear Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50 Reminder . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 695 Snow Chains (Tire Chains) . . . . . . . . . . . . . . . . . . .512 Snow Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .505 Spare Tire . . . . . . . . . . . . . . . . . . . . .506, 507, 508, 559 Spark Plugs . . . . . . . . . . . . . . . . . . . . . . . . . . . . .654 Specifications Fuel (Gasoline) . . . . . . . . . . . . . . . . . . . . . . . . .654 Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .654 Speed Control Accel/Decel . . . . . . . . . . . . . . . .
696 INDEX Telescoping Steering Column . . . . . . . . . . . . . . . . .175 Temperature Control, Automatic (ATC) . . . . . . . . . .416 Tilt Steering Column . . . . . . . . . . . . . . . . . . . . . . .175 Time Delay, Headlight . . . . . . . . . . . . . . . . . . . . . .160 Tip Start. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .448 Tire And Loading Information Placard . . . . . . .495, 496 Tire Markings . . . . . . . . . . . . . . . . . . . . . . . . . . . .488 Tires. . . . . . . . . . . .
INDEX 697 Traction Control . . . . . . . . . . . . . . . . . . . . . . . . . .481 Trailer Towing . . . . . . . . . . . . . . . . . . . . . . . . . . .538 Transaxle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .451 Automatic . . . . . . . . . . . . . . . . . . . . . . . . . . . .451 Autostick . . . . . . . . . . . . . . . . . . . . . . . . . . . . .461 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .451 Transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . .
698 INDEX Vehicle Loading . . . . . . . . . . . . . . . . . . . . . . .497, 536 Vehicle Modifications/Alterations . . . . . . . . . . . . . . .7 Vehicle Storage. . . . . . . . . . . . . . . . . . . . . . . .418, 638 Viscosity, Engine Oil . . . . . . . . . . . . . . . . . . . . . . .597 Voice Recognition System (VR) . . . . . . . . . . . . . . . .421 Warning Flasher, Hazard . . . . . . . . . . . . . . . . . . . .545 Warnings And Cautions . . . . . . . . . . . . . . . . . . . . . .6 Warranty Information . .
INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained personnel. The following must be observed during installation. The positive power connection should be made directly to the battery and fused as close to the battery as possible.
STICK WITH THE SPECIALISTS® 16UF-126-AB 16UF-126-AA ©2015 FCA US LLC. All Rights Reserved. Chrysler is a registered trademark of FCA US LLC. Second First Edition Printed in U.S.A.
