2015 200 2015 OWNER’S MANUAL Chrysler Group LLC 15UF-126-AC Third Edition Rev 1 Printed in U.S.A.
VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name Chrysler Group LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefore. DRIVING AND ALCOHOL Drunken driving is one of the most frequent causes of accidents. This manual illustrates and describes the operation of features and equipment that are either standard or optional on this vehicle.
SECTION TABLE OF CONTENTS PAGE 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115 3 4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION CONTENTS 䡵 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . .4 䡵 VEHICLE IDENTIFICATION NUMBER . . . . . . . .6 䡵 HOW TO USE THIS MANUAL . . . . . . . . . . . . . .4 䡵 VEHICLE MODIFICATIONS/ALTERATIONS . . . .7 䡵 WARNINGS AND CAUTIONS . . . . . . . . . . . . . .
4 INTRODUCTION When it comes to service, remember that your authorized dealer knows your vehicle best, has factory-trained techCongratulations on selecting your new Chrysler Group nicians and genuine parts, and cares about your satisfacLLC vehicle. Be assured that it represents precision tion. workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles.
INTRODUCTION 5 1
6 INTRODUCTION WARNINGS AND CAUTIONS This Owners Manual contains WARNINGS against operating procedures that could result in a collision or bodily injury. It also contains CAUTIONS against procedures that could result in damage to your vehicle. If you do not read this entire Owners Manual, you may miss important information. Observe all Warnings and Cautions.
INTRODUCTION 7 VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death. Stamped VIN Location NOTE: It is illegal to remove or alter the VIN.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS 䡵 A WORD ABOUT YOUR KEYS . . . . . . . . . . . . .12 ▫ To Arm The System . . . . . . . . . . . . . . . . . . . .19 ▫ Keyless Ignition Node (KIN) . . . . . . . . . . . . . .12 ▫ To Disarm The System . . . . . . . . . . . . . . . . . .19 ▫ Key Fob . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 ▫ Tamper Alert . . . . . . . . . . . . . . . . . . . . . . . . .20 ▫ Ignition Or Accessory On Message . . . . . . . . . .
10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Programming Additional Transmitters . . . . . . .25 ▫ Wind Buffeting . . . . . . . . . . . . . . . . . . . . . . .44 ▫ Transmitter Battery Replacement . . . . . . . . . . .25 䡵 TRUNK LOCK AND RELEASE . . . . . . . . . . . . .45 ▫ General Information . . . . . . . . . . . . . . . . . . . .27 䡵 TRUNK SAFETY WARNING. . . . . . . . . . . . . . . .46 䡵 REMOTE STARTING SYSTEM — IF EQUIPPED . .27 ▫ Trunk Emergency Release . . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 ▫ Safety Checks You Should Make Inside The Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111 ▫ Periodic Safety Checks You Should Make Outside The Vehicle . . . . . . . . . . . . . . . . . . . . . . . . .
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The Keyless Ignition Node (KIN System) has four operating positions, three of which are labeled and will Your vehicle uses a keyless ignition system. This system illuminate when in position. The three positions are OFF, consists of a Key Fob with Remote Keyless Entry (RKE) ACC, and ON/RUN. The fourth position is START, transmitter and a Keyless Ignition Node (KIN). during start RUN will illuminate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 Key Fob The Key Fob also contains the Remote Keyless Entry (RKE) transmitter and an emergency key, which stores in the rear of the Key Fob. The emergency key allows for entry into the vehicle should the battery in the vehicle or the Key Fob go dead. The emergency key is also for locking/unlocking the glove compartment. You can keep the emergency key with you when valet parking.
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Mechanical Latch On The Back Of The Key Fob Emergency Key Removal NOTE: You can insert the double-sided emergency key into the lock cylinders with either side up.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 Ignition Or Accessory On Message Opening the driver’s door when the ignition is in ACC or ON (engine not running), a chime will sound to remind you to cycle the ignition to OFF. In addition to the chime, the ignition or accessory on message will display in the cluster.
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • Do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. CAUTION! An unlocked car is an invitation to thieves. Always remove the Key Fob from vehicle, cycle the ignition OFF and lock all doors when leaving the vehicle unattended. SENTRY KEY® The Sentry Key® Immobilizer system prevents unauthorized vehicle operation by disabling the engine.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 If the Vehicle Security Light turns on during normal vehicle operation (vehicle running for longer than 10 seconds), it indicates that there is a fault in the electronics. Should this occur, have the vehicle serviced as soon as possible by an authorized dealer. CAUTION! • Do not make modifications or alterations to the immobilizer system. Modifications or alterations to the immobilization system may result in a loss of security protection.
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: When having the Sentry Key® Immobilizer Sys- NOTE: Changes or modifications not expressly approved tem serviced, bring all vehicle keys with you to an by the party responsible for compliance could void the user’s authority to operate the equipment. authorized dealer.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 To Arm The System To Disarm The System Follow these steps to arm the Vehicle Security Alarm: The Vehicle Security Alarm can be disarmed using any of the following methods: 1. Make sure the vehicle ignition is cycled to the ⬙OFF⬙ position. (refer to ⬙Starting Procedures⬙ in ⬙Starting • Push the UNLOCK button on the Remote Keyless And Operating⬙ for further information). Entry (RKE) transmitter. 2.
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The Vehicle Security Alarm remains armed during power trunk entry. Pressing the trunk button will not disarm the Vehicle Security Alarm. If someone enters the vehicle through the trunk and opens any door the alarm will sound. If the Vehicle Security Alarm is armed and the battery becomes disconnected, the Vehicle Security Alarm will remain armed when the battery is reconnected; the exterior lights will flash, the horn will sound.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 ILLUMINATED ENTRY The courtesy lights will turn on when you use the Remote Keyless Entry (RKE) transmitter to unlock the doors or open any door. This feature also turns on the approach lighting in the outside mirrors (if equipped). Refer to “Mirrors” in “Understanding The Features Of Your Vehicle” for further information.
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The Illuminated Entry system will not operate if the dimmer control is in the “Dome defeat” position (extreme bottom position). REMOTE KEYLESS ENTRY (RKE) The RKE system allows you to lock or unlock the doors, open the trunk, or activate the Panic Alarm from distances up to approximately 66 ft (20 m) using a hand-held Key Fob with RKE transmitter. The RKE transmitter does not need to be pointed at the vehicle to activate the system.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 If the vehicle is equipped with Passive Entry, refer to Keyless Enter-N-Go™ under “Things To Know Before Starting Your Vehicle” for further information. 1st Push Of Key Fob Unlocks This feature lets you program the system to unlock either the driver’s door or all doors on the first push of the UNLOCK button on the RKE transmitter. To change the current setting, refer to “Uconnect® Settings” in “Understanding Your Instrument Panel” for further information.
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE turned on or turned off. To change the current setting, refer to “Uconnect® Settings” in “Understanding Your This feature activates the headlights for up to 90 seconds Instrument Panel” for further information. when the doors are unlocked with the RKE transmitter. The time for this feature is programmable on vehicles To Unlatch The Trunk equipped through Uconnect®.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 The Panic Alarm will stay on for three minutes unless Programming Additional Transmitters you turn it off by either pushing the PANIC button a Programming Key Fobs or RKE transmitters may be second time or drive the vehicle at a speed of 15 mph performed at an authorized dealer. (24 km/h) or greater. Transmitter Battery Replacement NOTE: The recommended replacement battery is one CR2032 • The interior lights will turn off if you cycle the ignition battery.
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Emergency Key Removal Separating The RKE Transmitter Case 2. Insert the tip of the emergency key or a #2 flat blade 3. Remove the battery by turning the back cover over screwdriver into the slot and gently pry the two halves (battery facing downward) and tapping it lightly on a of the RKE transmitter apart. Make sure not to damage solid surface such as a table or similar, then replace the the seal during removal. battery.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 new battery with your fingers. Skin oils may cause If your RKE transmitter fails to operate from a normal battery deterioration. If you touch a battery, clean it distance, check for these two conditions: with rubbing alcohol. 1. A weak battery in the transmitter. The expected life of the battery is a minimum of three years. 4. To assemble the RKE transmitter case, snap the two halves together. 2.
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: • Brake switch inactive (brake pedal not pressed) • The vehicle must be equipped with an automatic • transmission to be equipped with Remote Start. • • Low fuel indicator must not be illuminated. • • Obstructions between the vehicle and the Key Fob may • reduce this range.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 WARNING! (Continued) • Keep Remote Keyless Entry (RKE) transmitters away from children. Operation of the Remote Start System, windows, door locks or other controls could cause serious injury or death. Remote Start Abort Messages on Your Instrument Cluster - 3.
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: To avoid unintentional shutdowns, the system will disable the one time push of the REMOTE START If an engine fault is present or fuel level is low, the button for two seconds after receiving a valid Remote vehicle will start and then shut down in 10 seconds. Start request. The park lamps will turn on and remain on during To Exit Remote Start Mode And Drive The Vehicle Remote Start mode.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 DOOR LOCKS Manual Door Locks To lock each door, rotate the door lock knob on each door trim panel forward. To unlock the front doors, pull the inside door handle to the first detent or rotate the door lock button until the red indicator is visible. To unlock the rear doors, rotate the door lock button until the red indicator is visible.
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! (Continued) • For personal security and safety in the event of a collision, lock the vehicle doors before you drive as well as when you park and leave the vehicle. • When leaving the vehicle, always remove the Key Fob from the ignition and lock your vehicle. • Never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 If you press the power door lock switch while the ignition is in the ACC or ON/RUN position, and any front door is open, the power locks will not operate. This prevents you from accidentally locking the Key Fob in the vehicle. Placing the ignition in the OFF position or closing the door will allow the locks to operate. If a door is open, and the ignition is in the ACC or ON/RUN position, a chime will sound as a reminder to remove the Key Fob.
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Automatic Unlock Doors On Exit Child-Protection Door Lock System — Rear The doors will unlock automatically on vehicles with Doors To provide a safer environment for children riding in the power door locks if: rear seat, the rear doors of your vehicle have a Child1. The Automatic Unlock Doors On Exit feature is enProtection Door Lock system. abled. The Child-Protection Door Locks are located inside the 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 2 Lock Child Protection Door Lock Unlock Child Protection Door Lock WARNING! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the Child-Protection locks are engaged.
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: For emergency exit with the system engaged, • If wearing gloves on your hands, or if it has been raining on the Passive Entry door handle, the unlock pull the toggle lock by the door handle (UNLOCKED sensitivity can be affected, resulting in a slower reposition), roll down the window, and open the door with sponse time. the outside door handle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 To Unlock From The Passenger Side — If Equipped With a valid Passive Entry RKE transmitter within 5 ft (1.5 m) of the passenger door handle, grab the front passenger door handle to unlock all four doors automatically. The interior door panel lock knob will raise when the door is unlocked.
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Preventing Inadvertent Locking Of Passive Entry RKE NOTE: The vehicle will only unlock the doors when the doors are locked using the door panel switch, a valid Transmitter In Vehicle Passive Entry RKE transmitter is detected inside the To minimize the possibility of unintentionally locking a vehicle, and no valid Passive Entry RKE transmitter is Passive Entry RKE transmitter inside your vehicle, the detected outside the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 To Enter The Trunk With a valid Passive Entry RKE transmitter within 3 ft (1.0 m) of the decklid, push the button located on the light bar between the license plate lamps. 2 NOTE: If you inadvertently leave your vehicle’s Passive Entry RKE transmitter in the trunk and try to close the decklid, the decklid will automatically unlatch, unless another one of the vehicle’s Passive Entry RKE transmitters is outside the vehicle and within 3 ft (1.
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: • After pressing the door handle LOCK button, you must wait two seconds before you can lock or unlock the doors, using either Passive Entry door handle. This is done to allow you to check if the vehicle is locked by pulling the door handle, without the vehicle reacting and unlocking. • The Passive Entry system will not operate if the RKE transmitter battery is dead.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 WINDOWS Power Windows The window controls on the driver’s door control all the door windows.
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE There are single window controls on each passenger door trim panel, which operate the passenger door windows. The window controls will operate only when the ignition is in the ACC or ON/RUN position. WARNING! (Continued) location accessible to children. Occupants, particularly unattended children, can become entrapped by the windows while operating the power window switches. Such entrapment may result in serious injury or death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 Front Windows Express Up And Down — If Equipped NOTE: • If the window runs into any obstacle during autoclosure, it will reverse direction and then go back down. Remove the obstacle and use the window Press the switch to the second detent and release. The switch again to close the window. window will go down automatically.
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE the DOWN position). To enable the window controls, press and release the window lockout button again Should the Auto Up feature stop working, the window (setting it in the UP position). may need to be reset. To reset Auto Up: Wind Buffeting 1. Make sure the door is fully closed. Wind buffeting can be described as the perception of 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 TRUNK LOCK AND RELEASE NOTE: The transmission must be in PARK before the button will operate. The trunk lid can be released from outside the vehicle by pressing the TRUNK button on the Remote Keyless Entry (RKE) transmitter twice within five seconds or by using the external release switch located on the underside of the decklid overhang. The release feature will function only when the vehicle is in the unlock condition.
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE TRUNK SAFETY WARNING WARNING! trunk can be simply opened by pulling on the glow-inthe-dark handle attached to the trunk latching mechanism. Do not allow children to have access to the trunk, either by climbing into the trunk from outside, or through the inside of the vehicle. Always close the trunk lid when your vehicle is unattended. Once in the trunk, young children may not be able to escape, even if they entered through the rear seat.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 2. If a child from 2 to 12 years old (not in a rear-facing child restraint) must ride in the front passenger seat, Some of the most important safety features in your move the seat as far back as possible and use the vehicle are the restraint systems: proper child restraint. (Refer to “Child Restraints.”) • Seat Belt Systems 3.
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 6. You should read the instructions provided with your child restraint to make sure that you are using it properly. 7. All occupants should always wear their lap and shoulder belts properly. 8. The driver and front passenger seats should be moved back as far as practical to allow the Advanced Front Air Bags room to inflate. WARNING! • Never place a rear-facing child restraint in front of an air bag.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 ejection and the risk of injury caused by striking the After the sequence completes, the Seat Belt Reminder inside of the vehicle. Everyone in a motor vehicle should Light remains illuminated until the respective seat belts are buckled. The driver should instruct all other occube belted at all times. pants to buckle their seat belts.
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: If BeltAlert® has been deactivated, the Seat Belt Reminder Light will continue to illuminate while the driver’s or outboard front passenger’s (if equipped with BeltAlert®) seat belt remains unbuckled. Lap/Shoulder Belts All seating positions in your vehicle are equipped with lap/shoulder belts. The seat belt webbing retractor will lock only during very sudden stops or collisions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 WARNING! (Continued) WARNING! (Continued) • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • Be sure everyone in your vehicle is in a seat and using a seat belt properly. • Wearing your seat belt incorrectly could make your injuries in a collision much worse. You might suffer internal injuries, or you could even slide out of the seat belt.
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) WARNING! (Continued) • A seat belt that is too loose will not protect you properly. In a sudden stop, you could move too far forward, increasing the possibility of injury. Wear your seat belt snugly. • A seat belt that is worn under your arm is dangerous. Your body could strike the inside surfaces of the vehicle in a collision, increasing head and neck injury. A seat belt worn under the arm can cause internal injuries.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2 2. The seat belt latch plate is above the back of the front seat, and next to your arm in the rear seat (for vehicles equipped with a rear seat). Grasp the latch plate and pull out the seat belt. Slide the latch plate up the webbing as far as necessary to allow the seat belt to go around your lap. Pulling Out The Latch Plate 3.
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Inserting Latch Plate Into Buckle Positioning The Lap Belt 4. Position the lap belt so that it is snug and lies low 5. Position the shoulder belt across the shoulder and across your hips, below your abdomen. To remove chest with minimal, if any slack so that it is comfortslack in the lap belt portion, pull up on the shoulder able and not resting on your neck. The retractor will belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 stowed position. If necessary, slide the latch plate down Adjustable Upper Shoulder Belt Anchorage the webbing to allow the seat belt to retract fully. In the driver and front passenger seats, the top of the shoulder belt can be adjusted upward or downward to Lap/Shoulder Belt Untwisting Procedure position the seat belt away from your neck.
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE As a guide, if you are shorter than average, you will prefer the shoulder belt anchorage in a lower position, and if you are taller than average, you will prefer the shoulder belt anchorage in a higher position. After you release the anchorage button, try to move it up or down to make sure that it is locked in position. Seat Belt Extender. The Seat Belt Extender should be used only if the existing seat belt is not long enough.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 NOTE: These devices are not a substitute for proper seat belt placement by the occupant. The seat belt still must be We recommend that pregnant women use the seat belts worn snugly and positioned properly. throughout their pregnancy. Keeping the mother safe is the best way to keep the baby safe. The pretensioners are triggered by the Occupant Restraint Controller (ORC).
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Automatic Locking Retractor (ALR) — If Equipped The seat belts in the passenger seating positions may be equipped with Switchable Automatic Locking Retractors (ALR) which are used to secure a child restraint system. For additional information, refer to “Installing Child Restraints Using The Vehicle Seat Belt” under the “Child Restraints” section of this manual. The table below defines the type of feature for each seating position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 as to not activate the ALR. If the ALR is activated, you will hear a ratcheting sound as the seat belt retracts. Allow the webbing to retract completely in this case and then carefully pull out only the amount of webbing necessary to comfortably wrap around the occupant’s mid-section. Slide the latch plate into the buckle until you hear a ⬙click.⬙ In Automatic Locking Mode, the shoulder belt is automatically pre-locked.
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE How To Disengage The Automatic Locking Mode Unbuckle the combination lap/shoulder belt and allow it to retract completely to disengage the Automatic Locking Mode and activate the vehicle sensitive (emergency) locking mode. WARNING! • The seat belt assembly must be replaced if the switchable Automatic Locking Retractor (ALR) feature or any other seat belt function is not working properly when checked according to the procedures in the Service Manual.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 • Knee Impact Bolsters Advanced Front Air Bags • Advanced Front Air Bags This vehicle has Advanced Front Air Bags for both the driver and front passenger as a supplement to the seat belt systems. The driver’s Advanced Front Air Bag is mounted in the center of the steering wheel. The passenger’s Advanced Front Air Bag is mounted in the instrument panel, above the glove compartment. The words SRS AIRBAG are embossed on the air bag covers.
62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Advanced Front Air Bag And Knee Impact Bolster Locations 1 — Driver And Passenger Advanced Front Air Bags 2 — Passenger Knee Impact Bolster / Supplemental Passenger Knee Air Bag 3 — Driver Knee Impact Bolster / Supplemental Driver Knee Air Bag • Being too close to the steering wheel or instrument panel during Advanced Front Air Bag deployment could cause serious injury, including death. Air bags need room to inflate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 This vehicle may be equipped with a driver and/or front passenger seat belt buckle switch that detects whether The Advanced Front Air Bag system has multistage the driver or front passenger seat belt is buckled. The seat driver and front passenger air bags. This system provides belt buckle switch may adjust the inflation rate of the output appropriate to the severity and type of collision as Advanced Front Air Bags.
64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • Do not put anything on or around the air bag covers or attempt to open them manually. You may damage the air bags and you could be injured because the air bags may no longer be functional. The protective covers for the air bag cushions are designed to open only when the air bags are inflating. • Relying on the air bags alone could lead to more severe injuries in a collision. The air bags work with your seat belt to restrain you properly.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 Seat belts are necessary for your protection in all colli- Occupant Classification System (OCS) — Front sions, and also are needed to help keep you in position, Passenger Seat away from an inflating air bag. The OCS is part of a Federally regulated safety system for When the ORC detects a collision requiring the Ad- this vehicle. It is designed to provide Passenger Advanced Front Air Bags, it signals the inflator units.
66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Occupant Classification Module (OCM) and Sensor • The front passenger seat is unoccupied or has very light objects on it; or The Occupant Classification Module (OCM) is located underneath the front passenger seat. The Sensor is lo- • The front passenger seat is occupied by a small pascated beneath the passenger seat cushion foam. Any senger, including a child; or weight on the seat will be sensed by the Sensor.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 Front Passenger Seat Occupant Status Properly seated adult Unoccupied seat Front Passenger Air Bag Output Full-power deployment OR reduced-power deployment Reduced-power deployment WARNING! • Never place a rear-facing child restraint in front of an air bag. A deploying Passenger Advanced Front Air Bag can cause death or serious injury to a child 12 years or younger, including a child in a rearfacing child restraint.
68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE In order for the OCS to operate as designed, it is important for the front passenger to be seated properly and properly wearing the seat belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 Decreasing the front passenger’s seated weight on the When a lighter weight passenger, including a small adult, front passenger seat may result in a reduced-power occupies the front passenger seat, the OCS may reduce the deployment of the Passenger Advanced Front Air Bag. inflation rate of the Passenger Advanced Front Air Bag. Increasing the front passenger’s seated weight on the This does not mean that the OCS is working improperly.
70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Objects are lodged under the front passenger seat. • Objects are lodged between the front passenger seat and center console. • Accessories that may change the seated weight on the front passenger seat are attached to the front passenger seat. • Anything that may decrease or increase the front passenger’s seated weight. The OCS determines the front passenger’s most probable classification.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 2 Not Seated Properly Not Seated Properly
72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Not Seated Properly • If an occupant in the front passenger seat is seated improperly, the occupant may provide an output signal to the OCS that is different from the occupant’s properly seated weight input. This may result in serious injury or death in a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 WARNING! (Continued) • Placing an object on the floor under the front passenger seat may prevent the OCS from working properly, which may result in serious injury or death in a collision. Do not place any objects on the floor under the front passenger seat. classify the seated weight of a front seat passenger, the OCS components must function as designed. Do not make any modifications to the front passenger seat components, assembly, or to the seat cover.
74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Do not add a secondary seat cover or mat. Knee Impact Bolsters • At no time should any Supplemental Restraint System (SRS) component or SRS related component or fastener be modified or replaced with any part except those which are approved by Chrysler Group LLC . The Knee Impact Bolsters help protect the knees of the driver and front passenger, and position the front occupants for improved interaction with the Advanced Front Air Bags.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 Supplemental Driver And Front Passenger Knee Air Bags This vehicle is equipped with a Supplemental Driver Knee Air Bag mounted in the instrument panel below the steering column and a Supplemental Passenger Knee Air Bag mounted in the instrument panel below the glove compartment. The Supplemental Knee Air Bags provide enhanced protection during a frontal impact by working together with the seat belts, pretensioners, and Advanced Front Air Bags.
76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE deploys through the seat seam into the space between the occupant and the door. The SAB moves at a very high speed and with such a high force that it could injure you if you are not seated properly, or if items are positioned in the area where the SAB inflates. Children are at an even greater risk of injury from a deploying air bag.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77 rollover events, in addition to the injury reduction potential provided by the seat belts and body structure. The SABICs deploy downward, covering the side windows. An inflating SABIC pushes the outside edge of the trim out of the way and covers the window. The SABICs inflate with enough force to injure you if you are not belted and seated properly, or if items are positioned in the area where the SABICs inflate.
78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The SABICs and SABs (“Side Air Bags”) are designed to activate in certain side impacts and certain rollover events. The Occupant Restraint Controller (“ORC”) determines whether the deployment of the Side Air Bags in a particular side impact or rollover event is appropriate, based on the severity and type of collision. Vehicle damage by itself is not a good indicator of whether or not Side Air Bags should have deployed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 79 WARNING! (Continued) • Relying on the Side Air Bags alone could lead to more severe injuries in a collision. The Side Air Bags work with your seat belt to restrain you properly. In some collisions, Side Air Bags won’t deploy at all. Always wear your seat belt even though you have Side Air Bags. deploys the left Side Air Bags only and a right side impact deploys the right Side Air Bags only.
80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE event may be in progress and whether deployment is If you do have a collision, which deploys the air bags, any appropriate. A slower-developing event may deploy the or all of the following may occur: seat belt pretensioners on both sides of the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 81 continues, see your doctor. If these particles settle on • After any collision, the vehicle should be taken to an your clothing, follow the garment manufacturer’s inauthorized dealer immediately. structions for cleaning. Enhanced Accident Response System Do not drive your vehicle after the air bags have de- In the event of an impact, if the communication network ployed.
82 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The ORC contains a backup power supply system that may deploy the air bags even if the battery loses power or In order to reset the Enhanced Accident Response System it becomes disconnected prior to deployment. functions after an event, the ignition switch must be changed from ignition START or ON/RUN to ignition The ORC turns on the Air Bag Warning Light in the OFF.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 83 free, if any of the following occurs, have an authorized dealer service the air bag system immediately. • The Air Bag Warning Light does not come on during the four to eight seconds when the ignition switch is first turned to the ON/RUN position. • The Air Bag Warning Light remains on after the four to eight-second interval.
84 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The Redundant Warning Light will stay on until the fault Maintaining Your Air Bag System is cleared. In addition, a single chime will sound to alert you that the Redundant Warning Light has come on and WARNING! a fault has been detected. If the Redundant Warning Light comes on intermittently or remains on while driv- • Modifications to any part of the air bag system could cause it to fail when you need it.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 85 WARNING! (Continued) • Do not attempt to modify any part of your air bag system. The air bag may inflate accidentally or may not function properly if modifications are made. Take your vehicle to an authorized dealer for any air bag system service. If your seat, including your trim cover and cushion, needs to be serviced in any way (including removal or loosening/tightening of seat attachment bolts), take the vehicle to your authorized dealer.
86 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE These data can help provide a better understanding of Child Restraints the circumstances in which crashes and injuries occur. Everyone in your vehicle needs to be buckled up at all NOTE: EDR data are recorded by your vehicle only if a times, including babies and children.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 87 WARNING! (Continued) great that you could not hold the child, no matter how strong you are. The child and others could be badly injured. Any child riding in your vehicle should be in a proper restraint for the child’s size. Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards. You should also make sure that you can install it in the vehicle where you will use it.
88 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Summary Of Recommendations For Restraining Children In Vehicles Infants and Toddlers Small Children Larger Children Children Too Large for Child Restraints Child Size, Height, Weight Or Age Children who are two years old or younger and who have not reached the height or weight limits of their child restraint Children who are at least two years old or who have out-grown the height or weight limit of their rear-facing child restraint Children who have out-g
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 89 Infants And Child Restraints Safety experts recommend that children ride rear-facing in the vehicle until they are two years old or until they reach either the height or weight limit of their rear-facing child restraint. Two types of child restraints can be used rear-facing: infant carriers and convertible child seats. The infant carrier is only used rear-facing in the vehicle.
90 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE remain in a forward-facing child seat with a harness for as long as possible, up to the highest weight or height allowed by the child seat. All children whose weight or height is above the forward-facing limit for the child seat should use a belt-positioning booster seat until the vehicle’s seat belts fit properly.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 91 WARNING! (Continued) • When your child restraint is not in use, secure it in the vehicle with the seat belt or LATCH anchorages, or remove it from the vehicle. Do not leave it loose in the vehicle. In a sudden stop or accident, it could strike the occupants or seatbacks and cause serious personal injury. Children Too Large For Booster Seats 1. Can the child sit all the way back against the back of the vehicle seat? 2.
92 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If the answer to any of these questions was “no,” then the child still needs to use a booster seat in this vehicle. If the child is using the lap/shoulder belt, check seat belt fit periodically and make sure the seat belt buckle is latched. A child’s squirming or slouching can move the seat belt out of position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 93 Recommendations For Attaching Child Restraints Restraint Type Rear-Facing Child Restraint Rear-Facing Child Restraint Forward-Facing Child Restraint Forward-Facing Child Restraint Combined Weight of the Child + Child Restraint Up to 65 lbs (29.5 kg) More than 65 lbs (29.5 kg) Up to 65 lbs (29.5 kg) More than 65 lbs (29.
94 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lower Anchors And Tethers For Children (LATCH) Restraint System Your vehicle is equipped with the child restraint anchorage system called LATCH, which stands for Lower Anchors and Tethers for CHildren. The LATCH system has three vehicle anchor points for installing LATCHequipped child seats. There are two lower anchorages located at the back of the seat cushion where it meets the seatback and one top tether anchorage located behind the seating position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 95 LATCH Positions For Installing Child Restraints In This Vehicle 2 • • Lower Anchorage Symbol 2 anchorages per seating position Top Tether Anchorage Symbol
96 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE What is the weight limit (child’s weight + weight of the child restraint) for using the LATCH anchorage system to attach the child restraint? 65 lbs (29.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 97 Can two child restraints be attached using a common lower LATCH anchorage? No Can the rear-facing child restraint touch the back of the front passenger seat? Yes Can the head restraints be removed? Yes Never “share” a LATCH anchorage with two or more child restraints.
98 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Locating The LATCH Anchorages The lower anchorages are round bars that are found at the rear of the seat cushion where it meets the seatback, below the anchorage symbols on the seatback. They are just visible when you lean into the rear seat to install the child restraint. You will easily feel them if you run your finger along the gap between the seatback and seat cushion.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 99 Locating The LATCH Anchorages There are tether strap anchorages behind each rear seating position located in the panel between the rear seatback and the rear window. They are found under a plastic cover with the tether anchorage symbol on it. 2 Tether Strap Anchorages LATCH-compatible child restraint systems will be equipped with a rigid bar or a flexible strap on each side.
100 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE tether strap. The tether strap will have a hook at the end to attach to the top tether anchorage and a way to tighten the strap after it is attached to the anchorage. Center Seat LATCH WARNING! (Continued) seat belt for installing child seats in the outboard positions. Please refer to “Installing The LATCHCompatible Child Restraint System” for typical installation instructions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 101 2. Loosen the adjusters on the lower straps and on the tether 6. Tighten all of the straps as you push the child restraint rearward and downward into the seat. Remove slack strap of the child seat so that you can more easily attach in the straps according to the child restraint manufacthe hooks or connectors to the vehicle anchorages. turer’s instructions. 3. Place the child seat between the lower anchorages for that seating position.
102 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE behind the child restraint, route the seat belt through the child restraint belt path and then buckle it. Do not lock the seatbelt. Remind all children in the vehicle that the seat belts are not toys and that they should not play with them. WARNING! • Improper installation of a child restraint to the LATCH anchorages can lead to failure of the restraint. The child could be badly injured or killed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 103 Lap/Shoulder Belt Systems For Installing Child Restraints In This Vehicle 2 • ALR = Switchable Automatic Locking Retractor • Top Tether Anchorage Symbol
104 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE What is the weight limit (child’s weight + weight of the child restraint) for using the Tether Anchor with the seat belt to attach a forward facing child restraint? Can the rear-facing child restraint touch the back of the front passenger seat? Weight limit of the Child Restraint Can the head restraints be removed? Can the buckle stalk be twisted to tighten the seat belt against the seat belt path of the child restraint? Yes Yes No Always use the tether
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 105 5. To lock the seat belt, pull down on the shoulder part of the seat belt until you have pulled all the seat belt webbing out of the retractor. Then, allow the webbing 1. Place the child seat in the center of the seating to retract back into the retractor. As the webbing position. For some second row seats, you may need to retracts, you will hear a clicking sound.
106 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 9. Test that the child restraint is installed tightly by 2. Rotate or lift the cover to access the anchor directly behind the seat where you are placing the child pulling back and forth on the child seat at the seat belt restraint. path. It should not move more than 1 inch (25.4 mm) in any direction. 3.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 107 5. Remove slack in the tether strap according to the child restraint manufacturer’s instructions. WARNING! Tether Strap Mounting 1 — Cover 3 — Attaching Strap A — Tether Strap Hook B — Tether Anchor 4. Attach the tether strap hook of the child restraint to the top tether anchorage as shown in the diagram. • An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child.
108 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE While cruising, brief full-throttle acceleration within the limits of local traffic laws contributes to a good break-in. Air Bags deploying in the front seat could harm your pet. Wide-open throttle acceleration in low gear can be detriAn unrestrained pet will be thrown about and possibly mental and should be avoided. injured, or injure a passenger during panic braking or in a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 109 NOTE: A new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered a normal part of the break-in and not interpreted as a problem. SAFETY TIPS Transporting Passengers NEVER TRANSPORT PASSENGERS IN THE CARGO AREA. WARNING! • Do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death.
110 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Exhaust Gas WARNING! (Continued) WARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (CO), follow these safety tips: • Do not run the engine in a closed garage or in confined areas any longer than needed to move your vehicle in or out of the area.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 111 Safety Checks You Should Make Inside The Vehicle Seat Belts not lit during starting, see your authorized dealer. If the light stays on, flickers, or comes on while driving, have the system checked by an authorized dealer. Inspect the seat belt system periodically, checking for cuts, frays, and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system.
112 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! (Continued) Pedals that cannot move freely can cause loss of vehicle control and increase the risk of serious personal injury. • Always make sure that floor mats are properly attached to the floor mat fasteners. • Never place or install floor mats or other floor coverings in the vehicle that cannot be properly secured to prevent them from moving and interfering with the pedals or the ability to control the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 113 Periodic Safety Checks You Should Make Outside The Vehicle Door Latches Tires Fluid Leaks Examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread or sidewall. Inspect the tread for cuts and cracks. Inspect sidewalls for cuts, cracks and bulges. Check the wheel nuts for tightness. Check the tires (including spare) for proper cold inflation pressure.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 䡵 MIRRORS . . . . . . . . . . . . . . . . . . . . . . . . . . . .122 ▫ Heated Mirrors — If Equipped . . . . . . . . . . .132 ▫ Inside Day/Night Mirror — If Equipped . . . .122 ▫ Illuminated Vanity Mirrors — If Equipped . . .132 ▫ Automatic Dimming Mirror — If Equipped . . .123 䡵 BLIND SPOT MONITORING (BSM) — IF EQUIPPED . . . . . . . . . . . . . . . . . . . . . . ▫ Outside Mirrors . . . . . . . . . . . . . . . . . . . . . .129 ▫ Rear Cross Path. . . .
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Front Heated Seats — If Equipped . . . . . . . . .147 ▫ Automatic Headlights — If Equipped . . . . . . .160 ▫ Front Ventilated Seats — If Equipped . . . . . . .149 ▫ Headlights On With Wipers (Available With Automatic Headlights Only) . . . . . . . . . . . . .161 ▫ Head Restraints . . . . . . . . . . . . . . . . . . . . . .149 ▫ Folding Rear Seat . . . . . . . . . . . . . . . . . . . . .152 䡵 DRIVER MEMORY SEAT — IF EQUIPPED . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 ▫ Front Map/Reading Lights . . . . . . . . . . . . . .166 ▫ To Activate . . . . . . . . . . . . . . . . . . . . . . . . . .179 ▫ Interior Lights . . . . . . . . . . . . . . . . . . . . . . .168 ▫ To Set A Desired Speed . . . . . . . . . . . . . . . . .180 ▫ Battery Saver Feature . . . . . . . . . . . . . . . . . .170 ▫ To Deactivate . . . . . . . . . . . . . . . . . . . . . . . .180 䡵 WINDSHIELD WIPERS AND WASHERS . . . . . .170 ▫ To Resume Speed . . .
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ To Turn Off . . . . . . . . . . . . . . . . . . . . . . . . . .189 ▫ To Resume . . . . . . . . . . . . . . . . . . . . . . . . . .189 ▫ To Vary The Speed Setting . . . . . . . . . . . . . . .190 ▫ Setting The Following Distance In ACC . . . . . .192 ▫ Overtake Aid . . . . . . . . . . . . . . . . . . . . . . . .196 ▫ ACC Operation At Stop . . . . . . . . . . . . . . . . .197 ▫ Adaptive Cruise Control (ACC) Menu . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 ▫ ParkSense® Warning Display . . . . . . . . . . . . .222 ▫ Cleaning The ParkSense® System . . . . . . . . . .247 ▫ ParkSense® Display . . . . . . . . . . . . . . . . . . . .222 ▫ ParkSense® System Usage Precautions. . . . . . .247 ▫ Enabling And Disabling ParkSense® . . . . . . . .228 䡵 PARKSENSE® ACTIVE PARK ASSIST SYSTEM — IF EQUIPPED . . . . . . . . . . . . . . . . . . . . . . . . .250 ▫ Service The ParkSense® Rear Park Assist System . . . . . . . . .
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 䡵 GARAGE DOOR OPENER — IF EQUIPPED . . .281 ▫ Closing Sunroof — Manual Mode . . . . . . . . . .292 ▫ Before You Begin Programming HomeLink® . . .282 ▫ Pinch Protect Feature . . . . . . . . . . . . . . . . . . .292 ▫ Programming A Rolling Code . . . . . . . . . . . . .283 ▫ Venting Sunroof — Express . . . . . . . . . . . . . .292 ▫ Programming A Non-Rolling Code . . . . . . . . .285 ▫ Sunshade Operation. . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 ▫ Venting Sunroof — Express . . . . . . . . . . . . . .296 ▫ Rear Seat Cupholders . . . . . . . . . . . . . . . . . .304 ▫ Opening Power Shade — Express . . . . . . . . . .297 䡵 STORAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . .305 ▫ Opening Power Shade — Manual Mode . . . . .297 ▫ Glove Compartment . . . . . . . . . . . . . . . . . . .305 ▫ Closing Power Shade — Express . . . . . . . . . . .297 ▫ Console Features . . . . . . . . . . . . . .
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Day/Night Mirror — If Equipped A single ball joint mirror is provided in the vehicle. It is a twist on mirror that has a fixed position at the windshield. The mirror installs on the windshield button with a counterclockwise rotation and requires no tools for mounting. The mirror head can be adjusted up, down, left, and right for various drivers. The mirror should be adjusted to center on the view through the rear window.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 • Press the Mirror Dimmer button a second time to turn the feature Off. A single ball joint mirror is provided in the vehicle. It is a twist on mirror that has a fixed position at the windshield. The mirror installs on the windshield button with a counterclockwise rotation and requires no tools for mounting. The mirror head can be adjusted up, down, left, and right for various drivers.
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The ASSIST and 9–1–1 features operate through • Vehicle Customer Care – Total support for all other the Uconnect® Access service. These buttons will only vehicle issues. operate as long as your Uconnect® Access service is 9-1-1 Call active. Refer to your “Uconnect® System supplement 1. Press the 9-1-1 Call button on the Rearview Mirror. manual” for further information.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 3. Once a connection between the vehicle and a 9-1-1 operator is made, the 9-1-1 Call system may transmit the following important vehicle information to a 9-1-1 operator: NOTE: Once a connection is made between the vehicle’s 9-1-1 Call system and the 9-1-1 operator, the 9-1-1 operator may be able to open a voice connection with the vehicle to determine if additional help is needed.
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! WARNING! (Continued) • If anyone in the vehicle could be in danger (e.g., fire or smoke is visible, dangerous road conditions or location), do not wait for voice contact from a 9-1-1 operator. All occupants should exit the vehicle immediately and move to a safe location. • The 9-1-1 Call system is embedded into the vehicle’s electrical system. Do not add aftermarket electrical equipment to the vehicle’s electrical system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 WARNING! (Continued) • Modifications to any part of the 9-1-1 Call system could cause the air bag system to fail when you need it. You could be injured if the air bag system is not there to help protect you. 9-1-1 Call System Limitations Vehicles sold in Canada and Mexico DO NOT have 9-1-1 Call system capabilities. 9-1-1 or other emergency line operators in Canada and Mexico may not answer or respond to 9-1-1 system calls.
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! (Continued) • The Occupant Restraint Control module turns on the Air Bag Warning Light on the instrument panel if a malfunction in any part of the system is detected. If the Air Bag Warning Light is illuminated, the air bag system may not be working properly and the 9-1-1 system may not be able to send a signal to a 9-1-1 operator. If the Air Bag Warning Light is illuminated, have an authorized dealer service the ORC system immediately.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 NOTE: Never place anything on or near the vehicle’s wireless and GPS antennas. You could prevent wireless and GPS signal reception, which can prevent your vehicle from placing an emergency call. Wireless and GPS signal reception is required for the 9-1-1 Call system to function properly. General Information This device complies with Part 15 of the FCC Rules.
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The third LED supplies illuminated entry lighting, which turns on in both mirrors when you use the Remote All outside mirrors are hinged and may be moved either Keyless Entry (RKE) transmitter or open any door. This forward or rearward to resist damage. The hinges have LED shines downward to illuminate the ground adjacent three detent positions: to the Front and Rear Doors.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 shifted out of REVERSE position. Each stored memory setting will have an associated Tilt Mirrors in Reverse position. NOTE: The Tilt Mirrors in Reverse feature is not turned on when delivered from the factory. The Tilt Mirrors in Reverse feature can be turned on and off using the Uconnect® System. Refer to “Uconnect® Settings/ Customer Programmable Features” in “Understanding Your Instrument Panel” for further information.
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Using the mirror control switch, press on any of the four Illuminated Vanity Mirrors — If Equipped arrows for the direction that you want the mirror to An illuminated vanity mirror is on each sun visor. To use move. the mirror, rotate the sun visor downward and swing the mirror cover upward. The light will turn on automatiHeated Mirrors — If Equipped cally. Closing the mirror cover will turn off the light. These mirrors are heated to melt frost or ice.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 Sun Visor “Slide-On Rod” Feature — If Equipped This feature allows for additional flexibility in positioning the visor to block out the sun. 1. Fold down the sun visor. 3 2. Unclip the visor from the center clip. 3. Pull the sun visor toward the inside rearview mirror to extend it.
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE vehicle speed reaches approximately 6 mph (10 km/h) or higher and will alert the driver of vehicles in these areas. NOTE: • The BSM system does NOT alert the driver about rapidly approaching vehicles that are outside the detection zones. • The BSM system detection zone DOES NOT change if your vehicle is towing a trailer. Therefore, visually verify the adjacent lane is clear for both your vehicle and trailer before making a lane change.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 properly. Do not block the area of the rear fascia where Entering From The Side the radar sensors are located with foreign objects (bumVehicles that move into your adjacent lanes from either per stickers, bicycle racks, etc.). side of the vehicle.
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Entering From The Rear Overtaking Traffic Vehicles that come up from behind your vehicle on either If you pass another vehicle slowly (with a relative speed side and enter the rear detection zone with a relative of less than 15 mph (24 km/h) and the vehicle remains in speed of less than 30 mph (48 km/h). the blind spot for approximately 1.5 seconds, the warning light will be illuminated.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 3 Overtaking/Approaching Overtaking/Passing The BSM system is designed not to issue an alert on The BSM system will not alert you of objects that are stationary objects such as guardrails, posts, walls, foliage, traveling in the opposite direction of the vehicle in berms, etc. However, occasionally the system may alert adjacent lanes. on such objects. This is normal operation and your vehicle does not require service.
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Stationary Objects Opposing Traffic WARNING! The Blind Spot Monitoring system is only an aid to help detect objects in the blind spot zones.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 WARNING! (Continued) system is not designed to detect pedestrians, bicyclists, or animals. Even if your vehicle is equipped with the BSM system, always check your vehicle’s mirrors, glance over your shoulder, and use your turn signal before changing lanes. Failure to do so can result in serious injury or death.
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: In a parking lot situation, oncoming vehicles can be obscured by vehicles parked on either side. If the sensors are blocked by other structures or vehicles, the system will not be able to alert the driver. Modes Of Operation Three selectable modes of operation are available in the Uconnect® System. Refer to “Uconnect® Settings/ Customer Programmable Features” in “Understanding Your Instrument Panel” for further information.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 turn signal is then activated, and it corresponds to an alert present on that side of the vehicle, an audible chime will also be sounded. Whenever a turn signal and detected object are present on the same side at the same time, both the visual and audible alerts will be issued. In addition to the audible alert the radio (if on) will also be muted.
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. The device must accept any interference received, including interference that may cause undesired operation of the device. Changes or modifications to any of these systems by other than an authorized service facility could void authorization to use this equipment. SEATS WARNING! (Continued) • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 Adjusting The Seat Up Or Down The height of the seats can be adjusted up or down. Pull upward or push downward on the seat switch, the seat will move in the direction of the switch. Release the switch when the desired position is reached. Tilting The Seat Up Or Down Power Seat Switch The angle of the seat cushion can be adjusted up or down.
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt, which could result in serious injury or death. Power Lumbar — If Equipped Power Seat Recliner Switch Vehicles equipped with power drivers seat may be equipped with power lumbar. The power lumbar switch is located on the outboard side of the power seat.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 3 Power Lumbar Switch Front Seat Adjustment While sitting in the seat, lift up on the bar and move the seat forward or rearward. Release the bar once you have Manual Front Seat Forward/Rearward Adjustment reached the desired position. Then, using body pressure, On models equipped with manual seats, the adjusting move forward and rearward on the seat to be sure that bar is located at the front of the seats, near the floor. the seat adjusters have latched.
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • Seats should be adjusted before fastening the seat belts and while the vehicle is parked. Serious injury or death could result from a poorly adjusted seat belt.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 Manual Seat Height Adjustment — If Equipped Front Heated Seats — If Equipped The driver’s seat height can be raised or lowered by The front heated seats control buttons are located within using a lever, located on the outboard side of the seat. the Uconnect® system. You can gain access to the control Pull upward on the lever to raise the seat height or push buttons through the climate screen or the controls screen.
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE time, the display will change from HI to LO, indicating the change. The LO-level setting will turn OFF automatically after approximately 45 minutes. NOTE: The engine must be running for the heated seats to operate. Vehicles Equipped With Remote Start On models that are equipped with remote start, the heated seats can be programed to come on during a remote start. This feature can be programmed through the Uconnect® system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 Front Ventilated Seats — If Equipped Located in the seat cushion are small fans that draw the air from the passenger compartment and blow air through fine perforations in the seat cover to help keep the driver and front passenger cooler in higher ambient temperatures. The fans operate at two speeds, HIGH and LOW. The front ventilated seats control buttons are located within the Uconnect® system.
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! The head restraints for all occupants must be properly adjusted prior to operating the vehicle or occupying a seat. Head restraints should never be adjusted while the vehicle is in motion. Driving a vehicle with the head restraints improperly adjusted or removed could cause serious injury or death in the event of a collision. To raise the head restraint, pull upward on the head restraint.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 NOTE: The head restraints should only be removed by qualified technicians, for service purposes only. If either of the head restraints require removal, see your authorized dealer. WARNING! Do not place items over the top of the Reactive Head Restraint, such as coats, seat covers or portable DVD players. These items may interfere with the operation of the Reactive Head Restraint in the event of a collision and could result in serious injury or death.
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Folding Rear Seat To provide additional storage area, the rear seatback can be folded forward. Pull on the loops to fold down either or both seatbacks.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 When returning the rear seatback to the upright position, DRIVER MEMORY SEAT — IF EQUIPPED be sure the seatback is latched. This feature allows the driver to store up to two different memory profiles, for easy recall through a memory WARNING! switch. Each memory profile contains desired position • Be certain that the seatback is securely locked into settings for the driver seat and side mirrors and a set of position.
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Adjust all memory profile settings to desired preferences (i.e., seat, side mirror and radio station presets). 3. Press and release the SET button on the memory switch, then press the number (1) button within five seconds. The Electronic Vehicle Information Center (EVIC) or Driver Information Display (DID), will display which memory position is being set. If desired, a second memory profile can be stored into memory as follows: 1.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 NOTE: Before programming your RKE transmitters you must select the “Memory To FOB” feature through the • Memory profiles can be set without the vehicle in Uconnect® system screen. Refer to “Uconnect® Settings ” PARK, but the vehicle must be in PARK to recall a in “Understanding Your Instrument Panel” for further memory profile. information.
156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Your RKE transmitters can be unlinked to your recall is cancelled, the driver seat will stop moving. A memory settings by pressing the SET (S) button, and delay of one second will occur before another recall can within 10 seconds, followed by pressing the UNLOCK be selected. button on the RKE transmitter.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 • The Easy Entry/Easy Exit feature is disabled when the TO OPEN AND CLOSE THE HOOD driver seat position is less than 0.9 in (22.7 mm) To open the hood, two levers must be released. forward of the rear stop. At this position, there is no benefit to the driver by moving the seat for Easy Exit 1. Pull the release lever located below the instrument panel and in front of the driver’s door. or Easy Entry.
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Safety Latch Lever Location Safety Latch Lever 3. Reach under the center front edge of the hood and 4. Lift the hood upward to the open position. push and hold the safety latch lever to the right.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 CAUTION! To prevent possible damage, do not slam the hood to close it. Use a firm downward push at the front center of the hood to ensure that both latches engage. WARNING! Be sure the hood is fully latched before driving your vehicle. If the hood is not fully latched, it could open when the vehicle is in motion and block your vision. Failure to follow this warning could result in serious injury or death.
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Headlights — If Equipped This system automatically turns the headlights on or off according to ambient light levels. To turn the system on, rotate the headlight switch clockwise to the last detent for automatic headlight operation. When the system is on, the headlight time delay feature is also on. This means the headlights will stay on for up to 90 seconds after you place the ignition into the OFF position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 To activate the delay feature, place the ignition in the OFF position while the headlights are still on. Then, turn off the headlights within 45 seconds. The delay interval When this feature is active, the headlights will turn on begins when the headlight switch is turned off. after the wipers are turned on if the headlight switch is placed in the AUTO position and programmable feature If you turn the headlights or parking lights on, or place is set to ON.
162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic High Beam Headlamp Control — If Equipped The Automatic High Beam Headlamp Control system provides increased forward lighting at night by automating high beam control through the use of a digital camera mounted on the inside rearview mirror. This camera detects vehicle specific light and automatically switches from high beams to low beams until the approaching vehicle is out of view.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 NOTE: If allowed by law in the country in which the vehicle was purchased the Daytime Running Lights can 1. Pull the multifunction lever toward you (or rearward be turned on and off using the Uconnect® System, refer in car) to manually deactivate the system (normal to “Uconnect® Settings” in “Understanding Your Instruoperation of low beams). ment Panel” for further information. 2.
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE headlight switch. To turn off the front fog lights, either press the headlight switch a second time or turn off the The front fog light switch is built into the headlight headlight switch. switch. An indicator light in the instrument cluster illuminates when the fog lights are turned on. Fog Lights — If Equipped NOTE: The fog lights will operate with the low beam headlights or parking lights on.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 Multifunction Lever Turn Signals The multifunction lever controls the operation of the turn Move the multifunction lever up or down and the arrows signals, headlight beam selection and passing lights. The on each side of the instrument cluster flash to show multifunction lever is located on the left side of the proper operation of the front and rear turn signal lights. steering column.
166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Lane Change Assist Front Map/Reading Lights Tap the lever up or down once, without moving beyond The front map/reading lights are mounted in the overthe detent, and the turn signal (right or left) will flash head console. three times then automatically turn off.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 3 Front Map/Reading Lights Center Buttons Front Map/Reading Lights Press Lenses NOTE: The lights also turn on when a door is opened. The two map/reading lights can be operated indepen- The lights will also turn on when the UNLOCK button on the RKE is pressed. dently by pressing the lenses. Front Map/Reading Lights — With Press Lenses Press the lens once to turn the light on. To turn the light off, press the lens a second time.
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Interior Lights The interior lights come on when a door is opened. To protect the battery, the interior lights will turn off automatically 10 minutes after the ignition is moved to the LOCK position. This will occur if the interior lights were switched on manually or are on because a door is open. This includes the glove box light, but not the trunk light.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 Ambient Light Control — If Equipped Dome Light Position Rotate the ambient dimmer control upward or downward to increase or decrease the brightness of the ambient light located in the overhead console, door handle lights, under I/P lights, door map pocket lights, and cubby bin lights. Rotate the instrument panel dimmer control completely upward to the second detent to turn on the interior lights.
170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Battery Saver Feature To protect the battery, the interior lights will turn off automatically 10 minutes after the ignition switch is moved to the LOCK position. This will occur if the interior lights were switched on manually or are on because a door is open. WINDSHIELD WIPERS AND WASHERS The windshield wiper/washer controls are located on the windshield wiper/washer lever on the right side of the steering column.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 NOTE: If snow packing occurs that obstructs the normal Rotate the end of the lever to one of the first four detent operation of the windshield wipers the following mespositions for intermittent settings, the fifth detent for low sage will appear in the Electronic Vehicle Information Center (EVIC) or the Driver Information Display (DID): wiper operation and the sixth detent for high wiper ⬙Front Wipers Blocked Cycle Switch or Clean the Windoperation. shield⬙.
172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Intermittent Wiper System Use one of the four intermittent wiper settings when weather conditions make a single wiping cycle, with a variable delay between cycles, desirable. At driving speeds above 10 mph (16 km/h), the delay can be regulated from a maximum of approximately 18 seconds between cycles (first detent), to a cycle every one second (fourth detent).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173 Windshield Washer Operation To use the washer, pull the lever rearward toward you and hold while spray is desired. If the lever is pulled while in the intermittent setting, the wipers will turn on and operate for several wipe cycles after the lever is released, and then resume the intermittent interval previously selected.
174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Sudden loss of visibility through the windshield could lead to a collision. You might not see other vehicles or other obstacles. To avoid sudden icing of the windshield during freezing weather, warm the windshield with the defroster before and during windshield washer use. NOTE: The mist feature does not activate the washer pump; therefore, no washer fluid will be sprayed on the windshield.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175 • The Rain Sensing feature may not function properly when ice, or dried salt water is present on the windThis feature senses moisture on the windshield and shield. automatically activates the wipers for the driver. The feature is especially useful for road splash or overspray • Use of Rain-X® or products containing wax or silicone from the windshield washers of the vehicle ahead. Rotate may reduce Rain Sensing performance.
176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Transmission In NEUTRAL Position — When the ignition is ON, and the automatic transmission is in the NEUTRAL position, the Rain Sensing system will not operate until the wiper switch is moved, vehicle speed is greater than 5 mph (8 km/h), or the shift lever/gear selector is moved out of the NEUTRAL position. TILT/TELESCOPING STEERING COLUMN This feature allows you to tilt the steering column upward or downward.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177 To unlock the steering column, pull the control handle down. To tilt the steering column, move the steering wheel upward or downward as desired. To lengthen or shorten the steering column, pull the steering wheel outward or push it inward as desired. To lock the steering column in position, push the control handle up until fully engaged. WARNING! Do not adjust the steering column while driving.
178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Vehicles Equipped With Remote Start WARNING! (Continued) On models that are equipped with remote start, the heated steering wheel can be programmed to come on during a remote start through the Uconnect® system. Refer to “Uconnect® Settings” in “Understanding Your Instrument Panel” for further information. • Do not place anything on the steering wheel that insulates against heat, such as a blanket or steering wheel covers of any type and material.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179 NOTE: In order to ensure proper operation, the Electronic Speed Control System has been designed to shut down if multiple Speed Control functions are operated at the same time. If this occurs, the Electronic Speed Control System can be reactivated by pushing the Electronic Speed Control ON/OFF button and resetting the desired vehicle set speed.
180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Leaving the Electronic Speed Control system on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the system OFF when you are not using it. To Set A Desired Speed Turn the Electronic Speed Control ON.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181 The speed increment shown is dependant on the chosen To Decrease Speed speed unit of U.S. (mph) or Metric (km/h): When the Electronic Speed Control is set, you can decrease speed by pushing the SET - button. U.S. Speed (mph) • Pressing the SET + button once will result in a 1 mph The speed decrement shown is dependant on the chosen increase in set speed. Each subsequent tap of the speed unit of U.S.
182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • If the button is continually pressed, the set speed will continue to decrease until the button is released, then the new set speed will be established. To Accelerate For Passing Press the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. Using Electronic Speed Control On Hills WARNING! Electronic Speed Control can be dangerous where the system cannot maintain a constant speed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 183 ACC will allow you to keep cruise control engaged in light to moderate traffic conditions without the constant need to reset your cruise control. ACC utilizes a radar sensor and a forward facing camera designed to detect a vehicle directly ahead of you. NOTE: • If the sensor does not detect a vehicle ahead of you, ACC will maintain a fixed set speed.
184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! (Continued) WARNING! (Continued) • Cannot take street, traffic, and weather conditions into account, and may be limited upon adverse sight distance conditions. • Does not always fully recognize complex driving conditions, which can result in wrong or missing distance warnings. • Will bring the vehicle to a complete stop while following a target vehicle and hold the vehicle for approximately 3 minutes in the stop position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 185 NOTE: Normal (fixed speed) electronic speed control will not react to preceding vehicles. Always be aware of the mode selected. You can change the mode by using the Cruise Control buttons. The two control modes function differently. Always confirm which mode is selected. 3 Adaptive Cruise Control (ACC) Operation The speed control buttons (located on the right side of the steering wheel) operates the ACC system.
186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Any chassis/suspension or tire size modifications NOTE: You cannot engage ACC under the following to the vehicle will effect the performance of the Adaptive conditions: Cruise Control and Forward Collision Warning System. • When you apply the brakes. Activating Adaptive Cruise Control (ACC) • When the parking brake is set. You can only engage ACC if the vehicle speed is above • When the automatic transmission is in PARK, RE0 mph (0 km/h).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 187 To Activate/Deactivate Push and release the Adaptive Cruise Control (ACC) ON/OFF button. The ACC menu in the EVIC/DID displays “ACC Ready.” time, the system will turn off and the EVIC/DID will display “Adaptive Cruise Control (ACC) Off.” 3 Adaptive Cruise Control Off Adaptive Cruise Control Ready To turn the system OFF, push and release the Adaptive Cruise Control (ACC) ON/OFF button again.
188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Leaving the Adaptive Cruise Control (ACC) system on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have a collision. Always leave the system off when you are not using it. NOTE: ACC cannot be set if there is a stationary vehicle in front of your vehicle in close proximity. Remove your foot from the accelerator pedal.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 189 • The shift lever/gear selector is removed from the To Resume Drive position. If there is a set speed in memory press the RES (resume) • The Electronic Stability Control/Traction Control Sys- button and then remove your foot from the accelerator pedal. The EVIC/DID will display the last set speed. tem (ESC/TCS) activates. • The vehicle parking brake is applied. NOTE: • Driver seatbelt is unbuckled at low speeds.
190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! The Resume function should only be used if traffic and road conditions permit. Resuming a set speed that is too high or too low for prevailing traffic and road conditions could cause the vehicle to accelerate or decelerate too sharply for safe operation. Failure to follow these warnings can result in a collision and death or serious personal injury.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 191 • If the button is continually pressed, the set speed will Metric Speed (km/h) continue to increase in 10 km/h increments until the • Pressing the SET - button once will result in a 1 km/h button is released. The increase in set speed is reflected decrease in set speed. Each subsequent tap of the in the EVIC/DID. button results in a decrease of 1 km/h.
192 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The ACC system decelerates the vehicle to a full stop when following a target vehicle. If an ACC host vehicle follows a target vehicle to a standstill, after two seconds the driver will either have to press the RES (resume) button, or apply the accelerator pedal to reengage the ACC to the existing Set Speed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 193 3 Distance Setting 4 Bars (Longest) Distance Setting 3 Bars (Long)
194 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Distance Setting 2 Bars (Medium) Distance Setting 1 Bar (Short) To increase the distance setting, press the Distance Setting — Increase button and release. Each time the button is pressed, the distance setting increases by one bar (longer).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 195 To decrease the distance setting, press the Distance • The system disengages. (Refer to the information on Setting — Decrease button and release. Each time the ACC Activation). button is pressed, the distance setting decreases by one The maximum braking applied by ACC is limited; howbar (shorter). ever, the driver can always apply the brakes manually, if If there is no vehicle ahead, the vehicle will maintain the necessary. set speed.
196 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Overtake Aid When driving with ACC engaged and following a target vehicle, the system will provide an additional acceleration to assist in passing vehicles in front. This additional acceleration is triggered when the driver utilizes the left turn signal. In locations with left hand drive traffic, Overtake Aid is active only when passing on the left hand side of the Target vehicles.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 197 While ACC is holding your vehicle at a standstill, if the In the event that the ACC system brings your vehicle to driver seatbelt is unbuckled or the driver door is opened, a standstill while following a target vehicle, if the target the parking brake will be activated, and the ACC system will be cancelled.
198 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Press the ADAPTIVE CRUISE CONTROL (ACC) ON/ The ACC screen may display once again if any ACC OFF button (located on the steering wheel) until one of activity occurs, which may include any of the following: the following displays in the EVIC/DID: • Distance Setting Change Adaptive Cruise Control Off • System Cancel When ACC is deactivated, the display will read “Adap• Driver Override tive Cruise Control Off.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 199 Display Warnings And Maintenance “Wipe Front Radar Sensor In Front Of Vehicle” Warning vehicle has left these areas. Under rare conditions, when the radar is not tracking any vehicles or objects in its path this warning may temporarily occur.
200 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Do not remove any screws from the sensor. Doing so NOTE: could cause an ACC system malfunction or failure and • If the “ACC/FCW Unavailable Wipe Front Radar require a sensor realignment. Sensor” message occurs frequently (e.g. more than • If the sensor or front end of the vehicle is damaged due once on every trip) without any snow, rain, mud, or to a collision, see your authorized dealer for service.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 201 obstructions, such as mud, dirt, or ice on windshield and fog on the inside of glass. In these cases, the EVIC/DID will display “ACC/FCW Limited Functionality Clean Front Windshield” and the system will have degraded performance. When the condition that created limited functionality is no longer present, the system will return to full functionality. NOTE: If the “ACC/FCW Limited Functionality Clean Front Windshield” message occurs frequently (e.g.
202 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Precautions While Driving With ACC In certain driving situations, ACC may have detection issues. In these cases, ACC may brake late or unexpectedly. The driver needs to stay alert and may need to intervene. Towing A Trailer NOTE: Towing a trailer is not advised when using ACC. Offset Driving ACC may not detect a vehicle in the same lane that is offset from your direct line of travel, or a vehicle merging Offset Driving Condition Example in from a side lane.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 203 the vehicle is out of the curve the system will resume Using ACC On Hills your original Set Speed. This is a part of normal ACC When driving on hills, ACC may not detect a vehicle in system functionality. your lane. Depending on the speed, vehicle load, traffic NOTE: On tight turns ACC performance may be limited. conditions, and the steepness of the hills, ACC performance may be limited.
204 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Lane Changing ACC may not detect a vehicle until it is completely in the lane in which you are traveling. In the illustration shown, ACC has not yet detected the vehicle changing lanes and it may not detect the vehicle until it’s too late for the ACC system to take action. ACC may not detect a vehicle until it is completely in the lane. There may not be sufficient distance to the lane-changing vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 205 Narrow Vehicles Stationary Objects And Vehicles Some narrow vehicles traveling near the outer edges of the lane or edging into the lane are not detected until they have moved fully into the lane. There may not be sufficient distance to the vehicle ahead. ACC does not react to stationary objects and stationary vehicles.
206 UNDERSTANDING THE FEATURES OF YOUR VEHICLE General Information Normal (Fixed Speed) Electronic Speed Control This vehicle has systems that operate on radio frequency Mode that comply with Part 15 of the Federal Communications In addition to Adaptive Cruise Control mode, a Normal Commission (FCC) rules and with Industry Canada (Fixed Speed) Electronic Speed Control mode is available for cruising at fixed speeds. The Normal (Fixed Speed) Standards RSS- GEN/210/220/310.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 207 WARNING! In the normal Cruise Control mode, the system will not react to vehicles ahead. In addition, the proximity warning does not activate and no alarm will sound even if you are too close to the vehicle ahead since neither the presence of the vehicle ahead nor the vehicle-to vehicle distance is detected. Be sure to maintain a safe distance between your vehicle and the vehicle ahead. Always be aware which mode is selected.
208 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • If the button is continually pressed, the set speed will Metric Speed (km/h) continue to increase in 5 mph increments until the • Pressing the SET - button once will result in a 1 km/h button is released. The increase in set speed is reflected decrease in set speed. Each subsequent tap of the in the EVIC/DID display. button results in a decrease of 1 km/h.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 209 • The vehicle parking brake is applied. • The ignition is turned off. • The braking temperature exceeds normal range (over- • The Adaptive Cruise Control (ACC) On/Off button is pressed. heated). • The shift lever/gear selector is removed from the FORWARD COLLISION WARNING (FCW) WITH Drive position.
210 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: FCW monitors the information from the forward looking sensors as well as the Electronic Brake Controller (EBC), to calculate the probability of a forward collision. When the system determines that a forward collision is probable, the driver will be provided with audible and visual warnings and may provide a brake jerk warning. the potential forward collision.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 211 When the system determines a collision with the vehicle in front of you is no longer probable, the warning message will be deactivated. NOTE: • The minimum speed for FCW activation is 1 mph (2 km/h). • The FCW alerts may be triggered on objects other than vehicles such as guard rails or sign posts based on the course prediction. This is expected and is a part of normal FCW activation and functionality.
212 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To turn the FCW system back ON, press the forward collision button again to turn the system ON (LED turns off). • Changing the FCW status to “Off” prevents the system from warning you of a possible collision with the vehicle in front of you. • Changing the FCW sensitivity - Near vs. Far. Far warns the driver of a possible collision earlier and Near warns the driver later.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 213 Changing FCW And Active Braking Status NOTE: The FCW Sensitivity And Active Braking Settings are • The system will retain the last setting selected by the programmable through the Uconnect® System. Refer to driver after ignition shut down. “Uconnect® Settings” in “Understanding Your Instru• FCW may not react to irrelevant objects such as ment Panel” for further information.
214 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Once the condition that limited the system performance is no longer present, the system will return to its full performance state. If the problem persists, see your authorized dealer. LaneSense system uses a forward looking camera to detect lane markings and measure vehicle position within the lane boundaries.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 215 driver to remain within the lane. When only a single lane marking is detected, a haptic (torque) warning will not be provided. NOTE: When operating conditions have been met, the LaneSense system will monitor if the driver’s hands are on the steering wheel and provides an audible warning to the driver when the driver’s hands are not detected on the steering wheel. The system will cancel if the driver does not return their hands to the wheel.
216 UNDERSTANDING THE FEATURES OF YOUR VEHICLE LaneSense Warning Message The LaneSense system will indicate the current lane drift condition through the Driver Information Display (DID). 7.0 Driver Information Display (DID) Screen — If Equipped When the LaneSense system is ON; the lane lines are gray when both of the lane boundaries have not been detected and the LaneSense indicator is solid white.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 217 • When the LaneSense system senses the lane has been approached and is in a lane departure situation, the left thick lane line flashes yellow (on/off), the left thin line remains solid yellow and the LaneSense indicator changes from solid white to flashing yellow.
218 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The LaneSense system operates with the similar behavior for a right lane departure when only the right lane marking has been detected. Left Lane Departure — Both Lanes Detected • When the LaneSense system is ON, the lane lines turn from gray to white to indicate that both of the lane markings have been detected.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 219 • For example: If approaching the left side of the lane the steering wheel will turn to the right. thin line remains solid yellow. The LaneSense indicator changes from solid yellow to flashing yellow. At this time torque is applied to the steering wheel in the opposite direction of the lane boundary. • For example: If approaching the left side of the lane the steering wheel will turn to the right.
220 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Changing LaneSense Status The LaneSense system settings can be configured through the Uconnect® system screen. Follow these steps to change the LaneSense settings: 1. Press the “Controls” button on touchscreen located on the bottom of the Uconnect® display. 2. Press the “Settings” button. 3. Press the “Safety & Driving Assistance” button.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 221 ParkSense® will retain the last system state (enabled or • When enabled the system operates above 37 mph disabled) from the last ignition cycle when the ignition is changed to the ON/RUN position. (60 km/h) and below 112 mph (180 km/h). ParkSense® can be active only when the shift lever/gear • Use of the turn signal suppresses the warnings. selector is in REVERSE.
222 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ParkSense® Sensors The ParkSense® Warning screen is located within the EVIC/DID. It provides visual warnings to indicate the distance between the rear fascia/bumper and the detected obstacle. Refer to “Electronic Vehicle Information Center (EVIC) or Driver Information Display (DID)” for further information. The four ParkSense® sensors, located in the rear fascia/ bumper, monitor the area behind the vehicle that is within the sensors’ field of view.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 223 If an obstacle is detected in the center rear region, the display will show a single solid arc in the center rear region and will produce a one-half second tone. As the vehicle moves closer to the obstacle, the display will show the single arc moving closer to the vehicle and the sound tone will change from slow, to fast, to continuous.
224 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Slow Tone/Solid Arc Slow Tone/Solid Arc
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 225 3 Fast Tone/Flashing Arc Continuous Tone/Flashing Arc
226 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The vehicle is close to the obstacle when the warning display shows one flashing arc and sounds a continuous tone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 227 Audible Alert Chime Radio Volume Reduced None No Single 1/2Second Tone (for rear center only) Yes WARNING ALERTS Slow Slow (for rear (for rear center center only) only) Yes NOTE: ParkSense® will reduce the volume of the radio, if on, when the system is sounding an audio tone.
228 UNDERSTANDING THE FEATURES OF YOUR VEHICLE When the ParkSense® switch is pressed to disable the ParkSense® can be enabled and disabled with the system, the instrument cluster will display the ParkSense® switch, located on the switch panel below “PARKSENSE OFF” message for approximately five seconds. Refer to “Electronic Vehicle Information Center the Uconnect® display. (EVIC) or 7⬙ Driver Information Display (DID)” for further information.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 229 Service The ParkSense® Rear Park Assist System During vehicle start up, when the ParkSense® Rear Park Assist System has detected a faulted condition, the instrument cluster will actuate a single chime, once per ignition cycle, and it will display the “PARKSENSE UNAVAILABLE WIPE REAR SENSORS” or the “PARKSENSE UNAVAILABLE SERVICE REQUIRED” message.
230 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ParkSense® System Usage Precautions NOTE: • ParkSense®, when on, will reduce the volume of the radio when it is sounding a tone. • Clean the ParkSense® sensors regularly, taking care not to scratch or damage them. The sensors must not be covered with ice, snow, slush, mud, dirt or debris. Failure to do so can result in the system not working • Jackhammers, large trucks, and other vibrations could properly.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 231 CAUTION! WARNING! • ParkSense® is only a parking aid and it is unable to recognize every obstacle, including small obstacles. Parking curbs might be temporarily detected or not detected at all. Obstacles located above or below the sensors will not be detected when they are in close proximity. • The vehicle must be driven slowly when using ParkSense® in order to be able to stop in time when an obstacle is detected.
232 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! (Continued) • Before using ParkSense®, it is strongly recommended that the ball mount and hitch ball assembly is disconnected from the vehicle when the vehicle is not used for towing. Failure to do so can result in injury or damage to vehicles or obstacles because the hitch ball will be much closer to the obstacle than the rear fascia when the loudspeaker sounds the continuous tone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 233 • The automatic braking function may only be applied if NOTE: the vehicle deceleration is not enough to avoid collid• The driver is always responsible for controlling the ing with a detected obstacle. vehicle. • The automatic braking function may not be applied • The system is provided to assist the driver and not to fast enough for obstacles that move toward the rear of substitute the driver. the vehicle from the left and/or right sides.
234 UNDERSTANDING THE FEATURES OF YOUR VEHICLE until the vehicle speed is increased to approximately 7 mph (11 km/h) or above. When in REVERSE and above the system’s operating speed, a warning will appear in the EVIC/DID indicating the vehicle speed is too fast. The system will become active again if the vehicle speed is decreased to speeds less than approximately 6 mph (9 km/h).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 235 The ParkSense® Warning screen is located within the Electronic Vehicle Information Center (EVIC) or Driver Information Display (DID). It provides visual warnings to indicate the distance between the rear fascia/bumper and/or front fascia/bumper and the detected obstacle. Refer to “Electronic Vehicle Information Center (EVIC) or 7⬙ Driver Information Display (DID)” for further information.
236 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Single 1/2 Second Tone/Solid Arc Slow Tone/Solid Arc
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 237 3 Slow Tone/Solid Arc Fast Tone/Flashing Arc
238 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Fast Tone/Flashing Arc Continuous Tone/Flashing Arc
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 239 The vehicle is close to the obstacle when the warning display shows one flashing arc and sounds a continuous tone.
240 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Audible Alert Chime None Radio Volume Reduced No Single 1/2Second Tone (for rear center only) Yes WARNING ALERTS Slow Slow (for rear (for rear center center only) only) Yes NOTE: ParkSense® will reduce the volume of the radio, if on, when the system is sounding an audio tone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 241 fast sound tone will be produced when reaching the 2nd flashing arc and will change to a continuous sound tone When the vehicle is in DRIVE the ParkSense® Warning when the 1st flashing arc appears. screen will be displayed when an obstacle is detected.
242 UNDERSTANDING THE FEATURES OF YOUR VEHICLE No Tone/Solid Arc No Tone/Flashing Arc
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 243 3 Fast Tone/Flashing Arc Continuous Tone/Flashing Arc
244 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The vehicle is close to the obstacle when the warning display shows one flashing arc and sounds a continuous tone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 245 Front Park Assist Audible Alerts Enabling And Disabling ParkSense® ParkSense® will turn off the Front Park Assist audible ParkSense® can be enabled and disabled with the alert (chime) after approximately three seconds when an ParkSense® switch, located on the switch panel below obstacle has been detected, the vehicle is stationary, and the Uconnect® display. brake pedal is applied.
246 UNDERSTANDING THE FEATURES OF YOUR VEHICLE “PARKSENSE OFF” message for approximately five seconds. Refer to “Electronic Vehicle Information Center (EVIC) or 7⬙ Driver Information Display (DID)” for further information. When the shift lever is moved to REVERSE and the system is disabled, the EVIC/DID will display the “PARKSENSE OFF” message for as long as the vehicle is in REVERSE. The ParkSense® switch LED will be ON when ParkSense® is disabled or requires service.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 247 second pop-up duration. The car graphic will remain displayed for as long as the vehicle is in REVERSE. Refer to “Electronic Vehicle Information Center (EVIC) or ⬙ Driver Information Display (DID)” for further information.
248 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • When you move the shift lever to the REVERSE position and ParkSense® is turned off, the instrument cluster will display “PARKSENSE OFF” for as long as the vehicle is in REVERSE. system misinterpreting a close object as a sensor problem, causing the “PARKSENSE UNAVAILABLE SERVICE REQUIRED” message to be displayed in the instrument cluster.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 249 CAUTION! (Continued) WARNING! (Continued) • The vehicle must be driven slowly when using ParkSense® in order to be able to stop in time when an obstacle is detected. It is recommended that the driver looks over his/her shoulder when using ParkSense®. • Before using ParkSense®, it is strongly recommended that the ball mount and hitch ball assembly is disconnected from the vehicle when the vehicle is not used for towing.
250 UNDERSTANDING THE FEATURES OF YOUR VEHICLE PARKSENSE® ACTIVE PARK ASSIST SYSTEM — IF EQUIPPED • The system is provided to assist the driver and not to substitute the driver.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 251 The system will also continuously perform the dynamic vehicle calibration to account for differences such as over or under inflated tires and new tires. Enabling And Disabling The ParkSense® Active Park Assist System 3 The ParkSense® Active Park Assist system can be enabled and disabled with the ParkSense® Active Park Assist switch, located on the switch panel below the Uconnect® display.
252 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The ParkSense® Active Park Assist system will turn off • The ParkSense® Active Park Assist system will allow a automatically for any of the following conditions: maximum of six shifts between DRIVE and REVERSE. If the maneuver cannot be completed within six shifts, • The parking maneuver is completed. the system will cancel and the EVIC/DID will instruct • Vehicle speed greater than 18 mph (30 km/h) when the driver to complete the maneuver manually.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 253 NOTE: If the vehicle is driven above approximately 15 mph (25 km/h), the EVIC/DID will instruct the driver to slow down. If the vehicle is driven above approximately 18 mph (30 km/h), the system will cancel. The driver must then reactivate the system by pressing the ParkSense® Active Park Assist switch.
254 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The driver needs to make sure that the selected parking space for the maneuver remains free and clear of any obstructions (e.g. pedestrians, bicycles, etc.). • The driver is responsible to ensure that the selected parking space is suitable for the maneuver and free/ clear of anything that may be overhanging or protruding into the parking space (e.g., ladders, tailgates, etc. from surrounding objects/vehicles).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 255 3 Parking Space Found — Keep Moving Forward Parking Space Found — Stop And Remove Hands From Wheel Once the vehicle is in position, you will be instructed to stop the vehicle’s movement and remove your hands Once the vehicle is at a standstill with your hands removed from the steering wheel, you will be instructed from the steering wheel. to place the shift lever into the REVERSE position.
256 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Parking Space Found — Shift To Reverse Check Surroundings — Wait For Steering To Complete When the driver places the shift lever into the REVERSE The system will then instruct the driver to check their position, the system may instruct the driver to wait for surroundings and move backward. steering to complete.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 257 • When the system instructs the driver to remove their hands from the steering wheel, the driver should check their surroundings and begin to back up slowly. • The ParkSense® Active Park Assist system will allow a maximum of six shifts between DRIVE or REVERSE. If the maneuver cannot be completed within six shifts, the system will cancel and the DID will instruct the driver to complete the maneuver manually.
258 UNDERSTANDING THE FEATURES OF YOUR VEHICLE When the vehicle has reached the end of its backward NOTE: It is the drivers responsibility to use the brake movement, the system will instruct the driver to check and stop the vehicle. The driver should check their their surroundings and stop the vehicle’s movement. surroundings and be prepared to stop the vehicle either when instructed to, or when driver intervention is required.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 259 3 Check Surroundings — Shift To Drive Check Surroundings — Wait For Steering To Complete When the driver places the shift lever into the DRIVE The system will then instruct the driver to check their position, the system may instruct the driver to wait for surroundings and move forward. steering to complete.
260 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Check Surroundings — Move Forward Check Surroundings — STOP When the vehicle has reached the end of its forward NOTE: It is the drivers responsibility to use the brake movement, the system will instruct the driver to check and stop the vehicle. The driver should check their their surroundings and stop the vehicle’s movement. surroundings and be prepared to stop the vehicle either when instructed to, or when driver intervention is required.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 261 Once the vehicle is in a standstill condition, the driver will be instructed to place the shift lever into the REVERSE position. 3 Check Surroundings — Wait For Steering To Complete The system will then instruct the driver to check their surroundings and move backward. Check Surroundings — Shift To Reverse When the driver places the shift lever into the REVERSE position, the system may instruct the driver to wait for steering to complete.
262 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Check Surroundings — Move Backward Your vehicle is now in the parallel park position. When the maneuver is complete, the driver will be instructed to check the vehicle’s parking position. If the driver is satisfied with the vehicle position, they should shift to PARK. The ⬙Active ParkSense Complete - Check Parking Position⬙ message will be momentarily displayed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 263 wheel switch to change your parking space setting to a NOTE: perpendicular maneuver. You may switch back to paral• When searching for a parking space, use the turn lel parking if you desire. signal indicator to select which side of the vehicle you Once the driver presses OK for a perpendicular parking want to perform the parking maneuver.
264 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • When seeking for a parking space, the driver should drive as parallel or perpendicular (depending on the type of maneuver) to other vehicles as possible. • The feature will only indicate the last detected parking space (example: if passing multiple available parking spaces, the system will only indicate the last detected parking space for the maneuver).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 265 3 Parking Space Found — Stop And Remove Hands From Wheel Parking Space Found — Shift To Reverse When the driver places the shift lever into the REVERSE Once the vehicle is at a standstill with your hands position, the system may instruct the driver to wait for removed from the steering wheel, you will be instructed steering to complete. to place the shift lever into the REVERSE position.
266 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Check Surroundings — Wait For Steering To Complete Check Surroundings — Move Backwards The system will then instruct the driver to check their NOTE: surroundings and move backward. • It is the drivers responsibility to use the brake and accelerator during the semi-automatic parking maneuver.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 267 • When the system instructs the driver to remove their When the vehicle has reached the end of its backward hands from the steering wheel, the driver should check movement, the system will instruct the driver to check their surroundings and stop the vehicle’s movement. their surroundings and begin to back up slowly. • The ParkSense® Active Park Assist system will allow a maximum of six shifts between DRIVE or REVERSE.
268 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: It is the drivers responsibility to use the brake and stop the vehicle. The driver should check their surroundings and be prepared to stop the vehicle either when instructed to, or when driver intervention is required. Once the vehicle is in a standstill condition, the driver will be instructed to place the shift lever into the DRIVE position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 269 3 Check Surroundings — Wait For Steering To Complete Check Surroundings — Move Forward The system will then instruct the driver to check their When the vehicle has reached the end of its forward surroundings and move forward. movement, the system will instruct the driver to check their surroundings and stop the vehicle’s movement.
270 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Once the vehicle is in a standstill condition, the driver will be instructed to place the shift lever into the REVERSE position. Check Surroundings — STOP NOTE: It is the drivers responsibility to use the brake and stop the vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 271 3 Check Surroundings — Wait For Steering To Complete Check Surroundings — Move Backwards The system will then instruct the driver to check their Your vehicle is now in the perpendicular park position. When the maneuver is complete, the driver will be insurroundings and move backward. structed to check the vehicle’s parking position. If the driver is satisfied with the vehicle position, they should shift to PARK.
272 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Active ParkSense Complete — Check Parking Position • The ParkSense® Active Park Assist system is only a parking aid and it is unable to recognize every obstacle, including small obstacles. Parking curbs might be temporarily detected or not detected at all. Obstacles located above or below the sensors will not be detected when they are in close proximity.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 273 WARNING! WARNING! (Continued) • Drivers must be careful when performing parallel or perpendicular parking maneuvers even when using the ParkSense® Active Park Assist system. Always check carefully behind and in front of your vehicle, look behind and in front of you, and be sure to check for pedestrians, animals, other vehicles, obstructions, and blind spots before backing up and moving forward.
274 UNDERSTANDING THE FEATURES OF YOUR VEHICLE PARKVIEW® REAR BACK UP CAMERA — IF EQUIPPED Your vehicle may be equipped with the ParkView® Rear Back Up Camera that allows you to see an on-screen image of the rear surroundings of your vehicle whenever the shift lever is put into REVERSE. The image will be displayed on the touchscreen display along with a caution note to “check entire surroundings” across the top of the screen. After five seconds this note will disappear.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 275 When the vehicle is shifted out of REVERSE (with camera delay turned ON), the camera image will continue to be displayed for up to 10 seconds after shifting out of REVERSE unless the vehicle speed exceeds 8 mph (13 km/h), the vehicle is shifted into PARK or the ignition is switched to the OFF position.
276 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: If snow, ice, mud, or any foreign substance builds up on the camera lens, clean the lens, rinse with water, and dry with a soft cloth. Do not cover the lens. WARNING! Drivers must be careful when backing up even when using the ParkView® Rear Back Up Camera. Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, obstructions, or blind spots before backing up.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 277 OVERHEAD CONSOLE The overhead console contains courtesy/reading lights and storage for sunglasses. Power sunroof and power sunshade switches may also be included, if equipped.
278 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Front Map/Reading Lights The front map/reading lights are mounted in the overhead console. Front Map/Reading Lights — With Center Buttons There are two map/reading light buttons located in the center of the overhead console that allow the lights to operate independently. Press the button once to turn the light on. To turn the light off, press the button a second time.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 279 NOTE: The lights also turn on when a door is opened. The two map/reading lights can be operated indepen- The lights will also turn on when the UNLOCK button on the RKE is pressed. dently by pressing the lenses. Sunglass Bin Door Press the lens once to turn the light on. Front Map/Reading Lights — With Press Lenses To turn the light off, press the lens a second time. The overhead console has a compartment which provides storage for a pair of sunglasses.
280 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Sunglass Bin Door — Rear Mounted Sunglass Bin Door — Front Mounted
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 281 GARAGE DOOR OPENER — IF EQUIPPED HomeLink® replaces up to three remote controls (handheld transmitters) that operate devices such as garage door openers, motorized gates, lighting or home security systems. The HomeLink® unit operates off your vehicle’s battery. 3 The HomeLink® buttons that are located in the sun visor designate the three different HomeLink® channels. HomeLink® Buttons NOTE: HomeLink® is disabled when the Vehicle Security Alarm is active.
282 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Your motorized door or gate will open and close while you are training the universal transceiver. Do not train the transceiver if people, pets or other objects are in the path of the door or gate. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by Federal safety standards. This includes most garage door opener models manufactured after 1982.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 283 To erase the channels place the ignition in the ON/RUN opener. It is NOT the button that is normally used to position and push and hold the two outside HomeLink® open and close the door. The name and color of the buttons (I and III) for up 20 seconds or until the red button may vary by manufacturer. indicator flashes. NOTE: • Erasing all channels should only be performed when programming HomeLink® for the first time.
284 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 1. Cycle the ignition to the ON/RUN position. 2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) away from the HomeLink® button you wish to program while keeping the HomeLink® indicator light in view. attached to the garage door opener/device motor. Firmly push and release the “LEARN” or “TRAINING” button. On some garage door openers/devices there may be a light that blinks when the garage door opener/device is in the LEARN/TRAIN mode.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 285 Reprogramming A Single HomeLink® Button (Rolling Code) Programming A Non-Rolling Code For programming Garage Door Openers manufactured To reprogram a channel that has been previously trained, before 1995. follow these steps: 1. Turn the ignition switch to the ON/RUN position. 1. Cycle the ignition to the ON/RUN position. 2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm) away from the HomeLink® button you wish to program 2.
286 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 5. Push and hold the programmed HomeLink® button 3. Without releasing the button proceed with “Programming A Non-Rolling Code” step 2 and follow all and observe the indicator light. remaining steps. • If the indicator light stays on constantly, programming is complete and the garage door/device should Canadian/Gate Operator Programming activate when the HomeLink® button is pushed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 287 2. Place the hand-held transmitter 1 to 3 inches (3 to 8 5. Push and hold the programmed HomeLink® button cm) away from the HomeLink® button you wish to and observe the indicator light. program while keeping the HomeLink® indicator • If the indicator light stays on constantly, programlight in view. ming is complete and the garage door/device should activate when the HomeLink® button is pushed. 3.
288 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Push and hold the desired HomeLink® button until To do this, push and hold the two outside buttons for 20 the indicator light begins to flash after 20 seconds. Do seconds until the red indicator flashes. Note that all channels will be erased. Individual channels cannot be not release the button. erased. 3.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 289 If you have any problems, or require assistance, please call toll-free 1-800-355-3515 or, on the Internet at HomeLink.com for information or assistance. WARNING! Vehicle exhaust contains carbon monoxide, a dangerous gas. Do not run your vehicle in the garage while programming the transceiver. Exhaust gas can cause serious injury or death. WARNING! (Continued) that has a “stop and reverse” feature as required by Federal safety standards.
290 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: • The transmitter has been tested and it complies with FCC and IC rules. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the device. • The term IC before the certification/registration number only signifies that Industry Canada technical specifications were met.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 291 WARNING! WARNING! (Continued) • Never leave children unattended in a vehicle, or with access to an unlocked vehicle. Never leave the Key Fob in or near the vehicle, or in a location accessible to children. Do not leave the ignition of a vehicle equipped with Keyless Enter-N-Go™ in the ACC or ON/RUN mode. Occupants, particularly unattended children, can become entrapped by the power sunroof while operating the power sunroof switch.
292 UNDERSTANDING THE FEATURES OF YOUR VEHICLE movement. The sunroof and sunshade will remain in a Pinch Protect Feature partially opened condition until the switch is pushed and This feature will detect an obstruction in the opening of held rearward again. the sunroof during Express Close operation. If an obstruction in the path of the sunroof is detected, the Closing Sunroof — Express sunroof will automatically retract.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 293 Sunshade Operation Sunroof Maintenance The sunshade can be opened manually. However, the Use only a non-abrasive cleaner and a soft cloth to clean sunshade will open automatically as the sunroof opens. the glass panel. NOTE: The sunshade cannot be closed if the sunroof is Ignition Off Operation open. The power sunroof switch will remain active for up to approximately ten minutes after the ignition switch is Wind Buffeting turned to the LOCK position.
294 UNDERSTANDING THE FEATURES OF YOUR VEHICLE POWER SUNROOF WITH POWER SHADE — IF EQUIPPED The power sunroof switches are located to the left between the sun visors on the overhead console. Power Shade Switches Power Sunroof Switches The power shade switches are located to the right between the sun visors on the overhead console.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 295 WARNING! WARNING! (Continued) • Never leave children unattended in a vehicle, or with access to an unlocked vehicle. Never leave the Key Fob in or near the vehicle, or in a location accessible to children. Do not leave the ignition of a vehicle equipped with Keyless Enter-N-Go™ in the ACC or ON/RUN mode. Occupants, particularly unattended children, can become entrapped by the power sunroof while operating the power sunroof switch.
296 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Opening Sunroof — Manual Mode Closing Sunroof — Manual Mode To open the sunroof, press and hold the switch rearward. The sunroof will (if the sunshade is in the closed position when the operation is initiated the sunshade will automatically open to the half open position prior to the sunroof opening) open to the full open position and automatically stop. Any release of the switch will stop the movement.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 297 Opening Power Shade — Express Closing Power Shade — Express Press the shade switch rearward and release it within one-half second and the shade will automatically open to the halfway position and stop automatically. Press the switch a second time from the halfway position and the shade will automatically open to the full open position and stop automatically. This is called “Express Open”.
298 UNDERSTANDING THE FEATURES OF YOUR VEHICLE windows together to minimize the buffeting. If the buffeting occurs with the sunroof open, adjust the sunThis feature will detect an obstruction in the opening of roof opening to minimize the buffeting or open any the sunroof during Express Close operation. If an obwindow. struction in the path of the sunroof is detected, the sunroof will automatically retract. Remove the obstruc- Sunroof Maintenance tion if this occurs.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 299 ELECTRICAL POWER OUTLETS — IF EQUIPPED Your vehicle is equipped with 12 Volt (13 Amp) power outlets that can be used to power cellular phones, small electronics and other low powered electrical accessories. The power outlets are labeled with either a “key” or a “battery” symbol to indicate how the outlet is powered.
300 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Front Center Console Outlet NOTE: To ensure proper operation a MOPAR® cigar knob and element must be used. • Do not exceed the maximum power of 160 Watts (13 Amps) at 12 Volts. If the 160 Watt (13 Amp) power rating is exceeded the fuse protecting the system will need to be replaced. • Power outlets are designed for accessory plugs only. Do not insert any other object in the power outlets as this will damage the outlet and blow the fuse.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 301 WARNING! (Continued) CAUTION! (Continued) • Do not touch with wet hands. • Close the lid when not in use and while driving the vehicle. • If this outlet is mishandled, it may cause an electric shock and failure. • Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.), will degrade the battery even more quickly. Only use these intermittently and with greater caution.
302 UNDERSTANDING THE FEATURES OF YOUR VEHICLE POWER INVERTER — IF EQUIPPED A 115 Volt (150 Watts Maximum) outlet is located on the forward wall of storage bin (below media center) of center console. This outlet can power cellular phones, electronics and other low power devices requiring power up to 150 Watts. Certain high-end video games, such as Playstation3 and XBox360 will exceed this power limit, as will most power tools. The power inverter is designed with built-in overload protection.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 303 WARNING! To avoid serious injury or death: • Do not insert any objects into the receptacles. • Do not touch with wet hands. • Close the lid when not in use. • If this outlet is mishandled, it may cause an electric shock and failure. CUPHOLDERS Front Seat Cupholders The cupholders are located in the center console forward of the armrest between the front seats.
304 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Seat Cupholders The rear seat cupholders are located in the center armrest between the rear seats. The cupholders are positioned forward in the armrest and side-by-side to provide convenient access to beverage cans or bottles while maintaining a resting place for the rear occupant’s elbows.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 305 STORAGE Glove Compartment The glove compartment is located on the passenger side of the instrument panel. Pull on the release handle to open the glove compartment. NOTE: The glove compartment handle is equipped with a lock. To lock the glove compartment, remove the emergency key from the key fob, insert emergency key into glove compartment handle lock cylinder and turn the key to the lock position and remove the key.
306 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Console Features There is a storage compartment located under the center console armrest. The armrest can be slid forward/rearward to allow driver/passenger comfort position. WARNING! Do not operate this vehicle with a console compartment lid in the open position. Driving with the console compartment lid open may result in injury in a collision. There is a front center console storage area located under the center console cupholder.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 307 3 Center Console Cupholder Release Front Center Console Storage Located inside the center console storage compartment is a line that indicates how much storage is allowed.
308 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Storage Compartment Fill Line NOTE: Filling the console storage area above this line may impede the sliding of the cupholder. Located inside the front of the console storage area power cords can be routed from the storage area to the center console pass-through.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 309 Door Storage The door panels contain storage areas with a bottle holder.
310 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Seat Armrest Storage — If Equipped CARGO AREA FEATURES For rear passengers there is a storage bin located in the Cargo Area — 60/40 Split-Folding Rear Seat — If armrest. Lift upward on the latch to open the storage Equipped compartment. The 60/40 split-folding rear seat provides cargo-carrying versatility. The seatbacks fold down easily by pulling the seatback loops between the seatbacks and the bolsters.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 311 3 Rear Seatback Loops After releasing the seatback, it can be folded forward. Folded Rear Seatback When the seatback is folded to the upright position, make sure it is latched by strongly pulling on the top of the seatback above the seat strap.
312 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! WARNING! • Be certain that the seatback is securely locked into position. If the seatback is not securely locked into position, the seat will not provide the proper stability for child seats and/or passengers. An improperly latched seat could cause serious injury. • The cargo area in the rear of the vehicle (with the rear seatbacks in the locked-up or folded down position) should not be used as a play area by children when the vehicle is in motion.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 313 Grocery Bag Hooks The rear cargo area is equipped with grocery bag hooks, located on either side of the rear cargo area. CAUTION! Do not exceed the maximum weight limit 35 lbs (16 kg) of the grocery bag hook. Damage may occur to hook and mounting surface. Ski Pass-Through There is a ski pass-through door located behind the rear seat armrest that allows longer items, such as snow skis, to be stored in the rear cargo area.
314 UNDERSTANDING THE FEATURES OF YOUR VEHICLE REAR WINDOW FEATURES Rear Window Defroster The rear window defroster button is located on the climate control. Press this button to turn on the rear window defroster and the heated outside mirrors (if equipped). An indicator in the button will illuminate when the rear window defroster is on. The rear window defroster automatically turns off after approximately 15 minutes. For an additional 5 minutes of operation, press the button a second time.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 315 CAUTION! Failure to follow these cautions can cause damage to the heating elements: • Use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements. Labels can be peeled off after soaking with warm water.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 INSTRUMENT PANEL FEATURES . . . . . . . . . .320 ▫ EVIC Selectable Menu Items . . . . . . . . . . . . .349 䡵 INSTRUMENT CLUSTER — BASE . . . . . . . . . .321 ▫ Screen Setup Driver Selectable Items . . . . . . . .354 䡵 INSTRUMENT CLUSTER — PREMIUM . . . . . .322 䡵 DRIVER INFORMATION DISPLAY (DID) . . . . .356 䡵 INSTRUMENT CLUSTER DESCRIPTIONS . . . . .323 䡵 ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) . . . . . . . . . . . . . . . . . . . . . . .
318 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Buttons On The Faceplate. . . . . . . . . . . . . . . .379 ▫ Manual Climate Controls . . . . . . . . . . . . . . . .400 ▫ Buttons On The Touchscreen. . . . . . . . . . . . . .379 ▫ Manual Climate Controls With Touchscreen — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . .405 ▫ Customer Programmable Features/Personal Settings — Uconnect® 5.0/8.4A/8.4AN Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 319 ▫ Media. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .429 ▫ Register (8.4A/8.4AN) . . . . . . . . . . . . . . . . . .436 ▫ Phone. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .430 ▫ Mobile App (8.4A/8.4AN) . . . . . . . . . . . . . . .437 ▫ Voice Text Reply . . . . . . . . . . . . . . . . . . . . . .432 ▫ Voice Texting (8.4A/8.4AN) . . . . . . . . . . . . . .438 ▫ Climate (8.4A/8.4AN) . . . . . . . . . . . . . . . . . .432 ▫ Yelp® (8.
320 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT PANEL FEATURES 1 2 3 4 5 — Air Outlet — EVIC/DID Controls — Instrument Cluster — Cruise/Adaptive Cruise Control — Ignition Switch 6 — Radio Screen 7 — Passenger Air Bag 8 — Glove Compartment 9 — Radio Controls 10 — Manual Climate Controls 11 — Steering Wheel 12 — Hood Release 13 — Headlight Switch
UNDERSTANDING YOUR INSTRUMENT PANEL 321 INSTRUMENT CLUSTER — BASE 4
322 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER — PREMIUM
UNDERSTANDING YOUR INSTRUMENT PANEL 323 INSTRUMENT CLUSTER DESCRIPTIONS 1. Red EVIC/DID Telltales 2. Amber EVIC/DID Telltales 3. Brake Warning Light has been corrected. If the problem is related to the brake booster, the ABS pump will run when applying the brake and a brake pedal pulsation may be felt during each stop. The dual brake system provides a reserve braking capacity in the event of a failure to a portion of the hydraulic system.
324 UNDERSTANDING YOUR INSTRUMENT PANEL WARNING! Driving a vehicle with the red brake light on is dangerous. Part of the brake system may have failed. It will take longer to stop the vehicle. You could have a collision. Have the vehicle checked immediately. The light also will turn on when the parking brake is applied with the ignition switch in the ON/RUN position. NOTE: This light shows only that the parking brake is applied it does not show the degree of brake application. 4.
UNDERSTANDING YOUR INSTRUMENT PANEL 325 6. Adaptive Cruise Control (ACC) Distance Setting Dis- 8. Turn Signal Indicators play The arrows will flash with the exterior turn signals when the turn signal lever is operated. This will display the distance setting for the A tone will chime, and an EVIC/DID message ACC system. For further information, refer to “Adaptive Cruise Control (ACC)” in “Underwill appear if either turn signal is left on for more than 1 mile (1.6 km). standing The Features Of Your Vehicle”.
326 UNDERSTANDING YOUR INSTRUMENT PANEL cycles, and the vehicle has been driven several miles 10. Air Bag Warning Light (kilometers) at speeds greater than 30 mph (48 km/h), see This light will turn on for four to eight seconds your authorized dealer as soon as possible to have the as a bulb check when the ignition switch is first problem diagnosed and corrected. turned to the ON/RUN position.
UNDERSTANDING YOUR INSTRUMENT PANEL 327 by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.
328 UNDERSTANDING YOUR INSTRUMENT PANEL replacement or alternate tires and wheels allow the TPMS 13. Antilock Brake System (ABS) to continue to function properly. This light monitors the Anti-Lock Brake System (ABS). The light will turn on when the ignition CAUTION! switch is turned to the ON/RUN position and may stay on for as long as four seconds. The TPMS has been optimized for the original equipment tires and wheels.
UNDERSTANDING YOUR INSTRUMENT PANEL 329 14. Fuel Filler Door Location 17. Engine Temperature The fuel pump symbol points to the side of the vehicle where the fuel door is located. When the engine temperature gets too high, the temperature icon will change color from light blue to red. 15. Fuel Gauge The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON/RUN position. 16.
330 UNDERSTANDING YOUR INSTRUMENT PANEL engine start. The vehicle should be serviced if the light stays on through several of your typical driving cycles. In most situations, the vehicle will drive normally and will not require towing. CAUTION! Prolonged driving with the Malfunction Indicator Light (MIL) on could cause damage to the engine control system. It also could affect fuel economy and driveability. If the MIL is flashing, severe catalytic converter damage and power loss will soon occur.
UNDERSTANDING YOUR INSTRUMENT PANEL 331 22. Vehicle Security Alarm 26. Temperature Gauge This light will flash rapidly for approximately 15 seconds when the vehicle theft alarm is arming. The light will flash at a slower speed continuously after the alarm is set. The security light will also come on for about three seconds when the ignition is first turned on. The temperature gauge shows engine coolant temperature.
332 UNDERSTANDING YOUR INSTRUMENT PANEL WARNING! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call an authorized dealer for service if your vehicle overheats. If you decide to look under the hood yourself, see “Maintaining Your Vehicle”. Follow the warnings under the Cooling System Pressure Cap paragraph.
UNDERSTANDING YOUR INSTRUMENT PANEL 333 ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) The EVIC Main Menu items consists of the following: • Speedometer The 3.5” Electronic Vehicle Information Center (EVIC) • Vehicle Info display is located in the instrument cluster.
334 UNDERSTANDING YOUR INSTRUMENT PANEL The system allows the driver to select information by • UP Arrow Button pressing the following buttons mounted on the steering Press and release the UP arrow button to scroll wheel: upward through the Main Menu items ( Speedometer, Vehicle Info, Fuel Economy, Trip A, Trip B, Stop/Start, Audio, Messages, Screen Set Up, Settings).
UNDERSTANDING YOUR INSTRUMENT PANEL 335 • BACK/LEFT Arrow Button Press and release the LEFT arrow button to access the information screens or submenu screens of a main menu item. • OK Button Push the OK button to access/select the information screens or submenu screens of a Main Menu item. Push and hold the OK arrow button for one second to reset displayed/selected features that can be reset. Electronic Vehicle Information Center (EVIC) — 3.5” Display The 3.
336 UNDERSTANDING YOUR INSTRUMENT PANEL 2. Brake Warning Light The dual brake system provides a reserve braking capacity in the event of a failure to a portion of the hydraulic system. A leak in either half of the dual brake system is indicated by the Brake Warning Light, which will turn on when the brake fluid level in the master cylinder has dropped below a specified level. This light monitors various brake functions, including brake fluid level and parking brake application.
UNDERSTANDING YOUR INSTRUMENT PANEL 337 WARNING! Driving a vehicle with the red brake light on is dangerous. Part of the brake system may have failed. It will take longer to stop the vehicle. You could have a collision. Have the vehicle checked immediately. The light also will turn on when the parking brake is applied with the ignition switch in the ON/RUN position. NOTE: This light shows only that the parking brake is applied. It does not show the degree of brake application. 3.
338 UNDERSTANDING YOUR INSTRUMENT PANEL 4. Main Display Area The main display area will normally display the main menu or the screens of a selected feature of the main menu. The main display area also displays “pop up” messages that consist of approximately 60 possible warning or information messages.
UNDERSTANDING YOUR INSTRUMENT PANEL 339 5. LaneSense Warning — If Equipped The LaneSense Warning system provides the driver with visual and steering torque warnings when the vehicle starts to drift out of its lane unintentionally without the use of a turn signal. • When the LaneSense Warning system is ON and ready the lane lines and LaneSense Warning indicator are the color gray.
340 UNDERSTANDING YOUR INSTRUMENT PANEL • Adaptive Cruise Control (ACC) Malfunction This light will turn on when a ACC is not operating and needs service. For further information, refer to “Adaptive Cruise Control (ACC)” in “Understanding The Features Of Your Vehicle”. • LaneSense Service — If Equipped This telltale will turn on to indicate that the LaneSense Departure has detected a failure. • Loose Fuel Filler Cap Message Indicator This telltale will turn on to indicate the fuel filler cap is loose.
UNDERSTANDING YOUR INSTRUMENT PANEL 341 10. Reconfigurable Red Telltale Display • Electronic Speed Control SET This light will turn on when the electronic • Oil Temperature Warning Light speed control is SET. For further information, This telltale indicates engine oil temperarefer to “Electronic Speed Control” in “Unture is high. If the light turns on while derstanding The Features Of Your Vehicle”. driving, stop the vehicle and shut off the engine as soon as possible.
342 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: • Even if power steering assistance is no longer operational, it is still possible to steer the vehicle. Under these conditions there will be a substantial increase in steering effort, especially at very low vehicle speeds and during parking maneuvers. • If the condition persists, see your authorized dealer for service. • Charging System Light This light shows the status of the electrical charging system.
UNDERSTANDING YOUR INSTRUMENT PANEL 343 briefly as a bulb check. If the light does not come on during starting, have the system checked by an authorized dealer. If a problem is detected, the light will come on while the engine is running. Cycle the ignition key when the vehicle has completely stopped and the shift lever is placed in the PARK position. The light should turn off. If the light remains lit with the engine running, your vehicle will usually be drivable.
344 UNDERSTANDING YOUR INSTRUMENT PANEL • Transmission Temperature Warning Light This light indicates that there is excessive transmission fluid temperature that might occur with severe usage such as trailer towing. It may also occur when operating the vehicle in a high torque converter slip condition. If this light comes on, stop the vehicle and run the engine at idle or faster, with the transmission in NEUTRAL until the light goes off.
UNDERSTANDING YOUR INSTRUMENT PANEL 345 CAUTION! WARNING! (Continued) Driving with a hot engine cooling system could damage your vehicle. If the temperature gauge reads “H” pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the “H” and you hear continuous chimes, turn the engine off immediately and call an authorized dealer for service. Vehicle”.
346 UNDERSTANDING YOUR INSTRUMENT PANEL release the OK button. To reset the oil change indicator Instrument Cluster Messages For (EVIC) And system (after performing the scheduled maintenance) (DID) refer to the following procedure. • Front Seatbelts Unbuckled 1. Without pushing the brake pedal, push the ENGINE • Driver Seatbelt Unbuckled START/STOP button and cycle the ignition to the • Passenger Seatbelt Unbuckled ON/RUN position (do not start the engine.) 2.
UNDERSTANDING YOUR INSTRUMENT PANEL 347 • Service Power Steering • Service Electronic Throttle Control • Cruise Off • Lights On • Cruise Ready • Right Turn Signal Light Out • Cruise Set To XXX MPH • Left Turn Signal Light Out • Cruise Set To XXX KM/H • Turn Signal On • Tire Pressure Screen With Low Tire(s) “Inflate Tire to • XX” • • Service Tire Pressure System • • Parking Brake Engaged • • Brake Fluid Low • • Service Electronic Braking System • • Engine Temperature Hot • • Battery Voltage Low •
348 UNDERSTANDING YOUR INSTRUMENT PANEL • Remote Start Aborted Hood Open • Autostick Unavailable Service Required • Remote Start Aborted Tailgate Open • Automatic Unavailable Use Autostick Service Req. • Remote Start Aborted Time Expired • Transmission Getting Hot Press Brake • Remote Start Disabled Start to Reset • Trans.
UNDERSTANDING YOUR INSTRUMENT PANEL 349 button to scroll through the information sub-menus and Push the OK button to select or reset the following Push and release the UP or DOWN arrow buttons until resettable sub-menus: the desired Selectable Menu icon is highlighted in the EVIC. Tire Pressure EVIC Selectable Menu Items Speedometer Push and release the UP or DOWN arrow button until Push and release the UP or DOWN arrow button until “Tire Pressure” is highlighted in the EVIC/DID.
350 UNDERSTANDING YOUR INSTRUMENT PANEL If the Tire Pressure system requires service, “Service Tire Fuel Economy Pressure System” is displayed. Push and release the UP or DOWN arrow button until Tire PSI is an information only function and cannot be the Fuel Economy icon is highlighted. reset. Push and release the LEFT arrow button to return • Average Fuel Economy/Miles Per Gallon (MPG or to the main menu.
UNDERSTANDING YOUR INSTRUMENT PANEL 351 Hold the OK button to reset feature information. Stored Messages Push and release the UP or DOWN arrow button until the Messages Menu displays in the EVIC/DID. This Push and release the UP or DOWN arrow button until feature shows the number of stored warning messages. the Stop/Start message is displayed in the EVIC/DID. Pushing the RIGHT arrow button will allow you to see Push and release the OK button to display the Stop/Start what the stored messages are. status.
352 UNDERSTANDING YOUR INSTRUMENT PANEL Vehicle Settings (EVIC) 1 2 3 4 5 6 7 8 9 10 11 12 Settings Language Select Units Select FCW Sensitivity ParkSense Blind Spot Alert Hill Start Assist Auto Lock Doors Auto Unlock Doors Passive Entry Remote Unlock Sequence Key Fob Linked to Memory Remote Start Comfort System Translation Message Language Units FCW Sensitivity ParkSense Blind Spot Alert Hill Start Asst Auto Lock Doors Auto Unlock Doors Passive Entry Remote Unlock Key in Memory Rmt Start Comfort Subme
UNDERSTANDING YOUR INSTRUMENT PANEL 353 Translation Message Horn w/ Rmt Start Submenu On, Off Horn w/ Rmt Lock On, Off 15 16 17 18 19 20 Settings Sound Horn with Remote Start Sound Horn with Remote Lock Flash Lights with Lock Daytime Running Lights Automatic Highbeams Headlights On with Wipers Rain Sensing Wipers Headlights Off Delay Lights w/ Lock Daytime Lights Auto Highbeams Lights w/ Wipers Auto Wipers Lights Off Delay 21 Key-Off Power Delay Power Off Delay 22 Illuminated Approach Lights w/
354 UNDERSTANDING YOUR INSTRUMENT PANEL 23 24 25 26 27 Settings Easy Exit Seat Tilt Mirror in Reverse Compass variance Calibrate Compass Brake Service Translation Message Easy Exit Seat Tilt Mirror in R Compass Var Compass Cal Brake Service 28 Auto Park Brake Auto Park Brake Submenu On, Off On, Off See Owner’s Manual, X Increment Press > to calibrate the compass Follow the VF specifically for this one On, Off Screen Setup Driver Selectable Items • Range To Empty (RTE) 1.
UNDERSTANDING YOUR INSTRUMENT PANEL 355 • Outside Temp (default) • Average MPG • Time • Current MPG • Range To Empty (RTE) • Trip A • Average MPG • Trip B • Current MPG • Audio Information NOTE: defaults will change to Average MPG UR, Range • Menu Title (Default Setting) UL if the proxies for Compass and Outside Temp are not • Digital Speedo available 4. Current Gear 3. Center • On • None • Off (Default) • Compass 5.
356 UNDERSTANDING YOUR INSTRUMENT PANEL DRIVER INFORMATION DISPLAY (DID) The DID Main Menu items consists of the following: The Driver Information Display (DID) features a driver- • Speedometer interactive display that is located in the instrument • Vehicle Info cluster.
UNDERSTANDING YOUR INSTRUMENT PANEL 357 The system allows the driver to select information by • UP Arrow Button pushing the following buttons mounted on the steering Push and release the UP arrow button to scroll wheel: upward through the main menu and submenus (Speedometer, Vehicle Info, Driver Assist, Fuel Economy, Trip Info, Stop/Start Info, Audio, Messages, Screen Setup).
358 UNDERSTANDING YOUR INSTRUMENT PANEL • BACK/LEFT Arrow Button Driver Information Display (DID) - 7ⴖ Display Push and release the LEFT arrow button to The 7” DID displays are located in the center portion of access the information screens or sub-menu the cluster. screens of a main menu item. • OK Button Push the OK button to access/select the information screens or sub-menu screens of a main menu item.
UNDERSTANDING YOUR INSTRUMENT PANEL 359 1. Red Reconfigurable Telltale Display • Power Steering System Over Temperature — If Equipped If the “SERVICE POWER STEERING” message and a steering wheel icon are displayed on the EVIC/DID screen, it indicates that the vehicle needs to be taken to the dealer for service. It is likely the vehicle has lost power steering assistance. Refer to “Power Steering” in “Starting And Operating” for further information.
360 UNDERSTANDING YOUR INSTRUMENT PANEL Do not operate the vehicle until the cause is corrected. This light does not show how much oil is in the engine. The engine oil level must be checked under the hood. • Charging System Light This light shows the status of the electrical charging system. If the light stays on or comes on while driving, turn off some of the vehicle’s non-essential electrical devices or increase engine speed (if at idle).
UNDERSTANDING YOUR INSTRUMENT PANEL 361 reduced performance, an elevated/rough idle or engine stall and your vehicle may require towing. • Oil Temperature Warning Light This telltale indicates engine oil temperature is high. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. • Air Bag Warning Light This light will turn on for four to eight seconds as a bulb check when the ignition switch is first turned to the ON/RUN position.
362 UNDERSTANDING YOUR INSTRUMENT PANEL WARNING! If you continue operating the vehicle when the Transmission Temperature Warning Light is illuminated you could cause the fluid to boil over, come in contact with hot engine or exhaust components and cause a fire. 2. Reconfigurable Info Area • Compass • Outside Temp • Time • Range • Average MPG • Current MPG 3.
UNDERSTANDING YOUR INSTRUMENT PANEL 363 • Loose Fuel Filler Cap Message Indicator 4. Brake Warning Light This telltale will turn on to indicate the fuel This light monitors various brake functions, filler cap is loose. including brake fluid level and parking brake application.
364 UNDERSTANDING YOUR INSTRUMENT PANEL The dual brake system provides a reserve braking capacity in the event of a failure to a portion of the hydraulic system. A leak in either half of the dual brake system is indicated by the Brake Warning Light, which will turn on when the brake fluid level in the master cylinder has dropped below a specified level. The light will remain on until the cause is corrected.
UNDERSTANDING YOUR INSTRUMENT PANEL 365 The light also will turn on when the parking brake is applied with the ignition switch in the ON/RUN position. NOTE: This light shows only that the parking brake is applied. It does not show the degree of brake application. 5. Driver Information Display (DID) The main display area will normally display the main menu or the screens of a selected feature of the main menu.
366 UNDERSTANDING YOUR INSTRUMENT PANEL • Five Second Unstored Messages When the appropriate conditions occur, this type of message takes control of the main display area for five seconds and then returns to the previous screen. An example of this message type is “Automatic High Beams On”. 6. Electronic Park Brake Failure This telltale indicates that there is an Electronic Park Brake Fault. Please see your authorized dealer for assistance. 7.
UNDERSTANDING YOUR INSTRUMENT PANEL 367 8. Reconfigurable Info Area • Compass • Outside Temp • Time • Range • Average MPG • Current MPG 9. Speed For Electronic Cruise Control Setting This displays the set speed of the Electronic Speed Control. • Electronic Speed Control SET This light will turn on when the electronic speed control is SET. For further information, refer to “Electronic Speed Control” in “Understanding The Features Of Your Vehicle”.
368 UNDERSTANDING YOUR INSTRUMENT PANEL 12. Low Fuel Display This area will display text to the visual warnings (i.e., “Push Brake To Start”). Odometer Display/Fuel Gauge/Temperature Gauge/ Submenu Area • The odometer display shows the total distance the vehicle has been driven. U.S. Federal regulations require that upon transfer of vehicle ownership, the seller certify to the purchaser the correct mileage that the vehicle has been driven.
UNDERSTANDING YOUR INSTRUMENT PANEL 369 CAUTION! WARNING! (Continued) Driving with a hot engine cooling system could damage your vehicle. If the temperature gauge reads “H” pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the “H” and you hear continuous chimes, turn the engine off immediately and call an authorized dealer for service. Vehicle”.
370 UNDERSTANDING YOUR INSTRUMENT PANEL release the OK button. To reset the oil change indicator system (after performing the scheduled maintenance) When the engine temperature gets too high, the refer to the following procedure. temperature icon will change color from light blue 1. Without pushing the brake pedal, push the ENGINE to red. START/STOP button and cycle the ignition to the Oil Change Reset ON/RUN position (do not start the engine.) Oil Change Due 2.
UNDERSTANDING YOUR INSTRUMENT PANEL 371 Instrument Cluster Messages For (EVIC) And (DID) • Front Seatbelts Unbuckled • Driver Seatbelt Unbuckled • Passenger Seatbelt Unbuckled • Service Airbag System • Service Power Steering • Cruise Off • Cruise Ready • Cruise Set To XXX MPH • Cruise Set To XXX KM/H • Traction Control Off • Tire Pressure Screen With Low Tire(s) “Inflate Tire to XX” • Washer Fluid Low • Service Tire Pressure System • Oil Pressure Low • Parking Brake Engaged • Oil Change Due • Brak
372 UNDERSTANDING YOUR INSTRUMENT PANEL • Service Electronic Throttle Control • Remote Start Aborted Hood Open • Lights On • Remote Start Aborted Tailgate Open • Right Turn Signal Light Out • Remote Start Aborted Time Expired • Left Turn Signal Light Out • Remote Start Disabled Start to Reset • Turn Signal On • Service Airbag System • Vehicle Not in Park • Service Airbag Warning Light • Key in Ignition • Door Open • Key in Ignition Lights On • Doors Open • Remote Start Active Key to Run •
UNDERSTANDING YOUR INSTRUMENT PANEL 373 • Transmission Getting Hot Press Brake EVIC Selectable Menu Items • Trans. Hot Stop Safely Shift to Park Wait to Cool • Transmission Cool Ready to Drive Push and release the UP or DOWN arrow buttons until the desired Selectable Menu icon is highlighted in the EVIC.
374 UNDERSTANDING YOUR INSTRUMENT PANEL button to scroll through the information sub-menus and If the Tire Pressure system requires service, “Service Tire Push the OK button to select or reset the following Pressure System” is displayed. resettable sub-menus: Tire PSI is an information only function and cannot be Tire Pressure reset. Push and release the LEFT arrow button to return to the main menu. Push and release the UP or DOWN arrow button until “Tire Pressure” is highlighted in the EVIC/DID.
UNDERSTANDING YOUR INSTRUMENT PANEL 375 Press the SET + or the SET- button (located on the The DID displays the current ACC system settings. The steering wheel) and the following will display in the DID: information displayed depends on ACC system status. ACC SET Adaptive Cruise Control (ACC) Menu Press the ADAPTIVE CRUISE CONTROL (ACC) ON/ When ACC is set, the set speed will display in the OFF button (located on the steering wheel) until one of instrument cluster.
376 UNDERSTANDING YOUR INSTRUMENT PANEL • The DID will return to the last display selected after • Range To Empty (RTE) five seconds of no ACC display activity. • Current Fuel Economy (MPG or L/100 km) For further information, refer to “Adaptive Cruise ConTrip Info trol (ACC) — If Equipped” in “Understanding The Push and release the UP or DOWN arrow button until Features Of Your Vehicle”. the Trip Menu item is highlighted in the EVIC (Toggle left LaneSense Menu or right to select Trip A or Trip B).
UNDERSTANDING YOUR INSTRUMENT PANEL 377 Stop/Start – If Equipped Screen Setup Push and release the UP or DOWN arrow button until the Stop/Start message is displayed in the EVIC/DID. Push and release the OK button to display the Stop/Start status. Push and release the UP or DOWN arrow button until the Screen Setup Menu displays in the EVIC/DID. Push and release the OK button to enter the sub-menus.
378 UNDERSTANDING YOUR INSTRUMENT PANEL Uconnect® 5.0 Buttons On Touchscreen And Buttons On Faceplate 1 — Uconnect® Buttons On The Faceplate 2 — Uconnect® Buttons On The Touchscreen Uconnect® 8.
UNDERSTANDING YOUR INSTRUMENT PANEL 379 Buttons On The Faceplate Buttons On The Touchscreen Buttons are located below the Uconnect® system in the center of the instrument panel. In addition, there is a Scroll/Enter control knob located on the right side of the Climate Controls in the center of the instrument panel. Turn the control knob to scroll through menus and change settings (i.e., 30, 60, 90), push the center of the control knob one or more times to select or change a setting (i.e., ON, OFF).
380 UNDERSTANDING YOUR INSTRUMENT PANEL equipped), Engine Off Options, Audio, Phone/ Display Bluetooth®, SiriusXM Setup, Restore Settings, Clear Per- After pressing the “Display” button on the touchscreen sonal Data (if equipped). the following settings will be available: NOTE: Only one category may be selected at a time. • Display Mode To adjust the setting of a programmable feature, press the desired setting option.
UNDERSTANDING YOUR INSTRUMENT PANEL 381 • Display Brightness With the Headlights Off • Units This feature allows you to select the display brightness when the headlights are off. Adjust the brightness with the + and – setting buttons on the touchscreen. Then press the back arrow button on the touchscreen, or push the back button on the faceplate. This feature allows you to select US or Metric units of measure in the EVIC/DID, odometer, and navigation system (if equipped).
382 UNDERSTANDING YOUR INSTRUMENT PANEL • Navigation Turn-By-Turn In Cluster — If Equipped When this feature is selected, the turn-by-turn directions will appear in the driver screen/EVIC/DID/Cluster display as the vehicle approaches a designated turn within a programmed route. To turn on or enable, press the “Navigation Turn-By-Turn In Cluster” button on the touchscreen, until a check-mark appears next to the setting, showing that setting has been selected.
UNDERSTANDING YOUR INSTRUMENT PANEL 383 buttons on the touchscreen to adjust the hours up or Press the back arrow button on the touchscreen to return to down. Press the back arrow button on the touchscreen to the previous menu, or push the back button on the faceplate. return to the previous menu or press the ”X” button on • Show Time In Status Bar — If Equipped the touchscreen to close out of the settings screen. This feature allows you to choose to show the time in the • Set Time Minutes Status bar.
384 UNDERSTANDING YOUR INSTRUMENT PANEL the Far setting. This means the system will warn you of a possible collision with the vehicle in front of you when you are farther away. This gives you the most reaction time. To change the setting for a more dynamic driving experience, select the Near setting. This warns you of a possible collision when you are much closer to the vehicle in front of you. To change the FCW status, press and release the “Near” or “Far” button.
UNDERSTANDING YOUR INSTRUMENT PANEL 385 • LaneSense Strength — If Equipped Refer to “ParkSense®” in “Understanding The Features Of Your Vehicle” for system function and operating When this feature is selected, it sets the strength of the information. steering wheel feedback for potential lane departures.
386 UNDERSTANDING YOUR INSTRUMENT PANEL • Rear ParkSense® Braking Assist — If Equipped appears next to setting, showing that setting has been selected. Press the back arrow button on the touchscreen When this feature is selected, the ParkSense® system will to return to the previous menu. detect objects located behind the vehicle and utilize autonomous braking to help stop the vehicle (only en- • Blind Spot Alert — If Equipped abled when ParkSense® is also on).
UNDERSTANDING YOUR INSTRUMENT PANEL 387 NOTE: If your vehicle has experienced any damage in the area where the sensor is located, even if the fascia is not damaged, the sensor may have become misaligned. Take your vehicle to an authorized dealer to verify sensor alignment. Having a sensor that is misaligned will result in the BSM not operating to specification.
388 UNDERSTANDING YOUR INSTRUMENT PANEL For further information, refer to “Electric Parking Brake touchscreen, and choose either 0 sec, 30 sec, 60 sec or 90 seconds. A check-mark appears next to setting indicating (EPD)” in “Starting and Operating.” that the setting has been selected. Press the back arrow • Auto Park Brake button on the touchscreen to return to the previous Auto Park Brake will set the park brake once the vehicle menu, or push the back button on the faceplate.
UNDERSTANDING YOUR INSTRUMENT PANEL 389 The headlights will also turn off when the wipers are turned off if they were turned on by this feature. To make your selection, press the “Headlights With Wipers” button on the touchscreen, until a check-mark appears next to setting, indicating that the setting has been selected. Press the back arrow button on the touchscreen to return to the previous menu, or push the back button on the faceplate.
390 UNDERSTANDING YOUR INSTRUMENT PANEL arrow button on the touchscreen to return to the previous selected. Press the back arrow button on the touchscreen menu, or push the back button on the faceplate. to return to the previous menu, or push the back button on the faceplate.
UNDERSTANDING YOUR INSTRUMENT PANEL 391 selection, press either the “Off,” “1st Press,” or “2nd Press” button on the touchscreen, until a check-mark appears next to setting, showing that setting has been selected. Press the back arrow button on the touchscreen to return to the previous menu, or push the back button on the faceplate. press of the Remote Keyless Entry (RKE) transmitter UNLOCK button. You must press the RKE transmitter UNLOCK button twice to unlock the passenger’s doors.
392 UNDERSTANDING YOUR INSTRUMENT PANEL • Passive Entry NOTE: The seat will return to the memorized seat location (if Recall Memory with Remote Key Unlock is set to ON) when the Remote Keyless Entry (RKE) transmitter is used to unlock the door. Refer to “Driver Memory Seat” in “Understanding The Features Of Your Vehicle” for further information. This feature allows you to lock and unlock the vehicles door(s) without having to press the Remote Keyless Entry (RKE) transmitter lock or unlock buttons.
UNDERSTANDING YOUR INSTRUMENT PANEL 393 when temperatures are below 40° F (4.4° C). When temperatures are above 80° F (26.7° C) the driver vented seat will turn on. To make your selection, press “Off,” “Remote Start Only,” OR “All Starts” checkbox until a check-mark appears next to the setting option. Select “Off,” “Remote Start Only” OR “All Starts” to determine when the feature is activated. Press the back arrow button on the touchscreen to return to the previous menu.
394 UNDERSTANDING YOUR INSTRUMENT PANEL setting, press the “Headlights Off Delay” button on the touchscreen, and choose either 0 sec, 30 sec, 60 sec or 90 seconds. A check-mark appears next to setting indicating that the setting has been selected. Press the back arrow button on the touchscreen to return to the previous menu, or push the back button on the faceplate. the scale between the “+” and “–” buttons on the touchscreen. Then press the back arrow button on the touchscreen.
UNDERSTANDING YOUR INSTRUMENT PANEL 395 • AUX Volume Match SiriusXM Setup This feature provides the ability to tune the audio level for portable devices connected through the AUX input. To make your selection, press the AUX Volume Match button on the touchscreen, choose a level from –3 to +3 followed by pressing the back arrow button on the touchscreen. After pressing the SIRIUS Setup button on the touchscreen the following settings will be available.
396 UNDERSTANDING YOUR INSTRUMENT PANEL Press the Subscription Info button on the touchscreen to select Yes to restore, or Cancel to exit. Once the settings are restored, a pop up appears stating ⬙settings reset to access the Subscription Information screen. default.⬙ Press the okay button on the touchscreen to exit. Write down the SIRIUS ID numbers for your receiver. To reactivate your service, either call the number listed on Clear Personal Data the screen or visit the provider online.
UNDERSTANDING YOUR INSTRUMENT PANEL 397 Uconnect® RADIOS — IF EQUIPPED For detailed information about your Uconnect® radio, refer to your Uconnect® Supplement Manual. iPod®/USB/MP3 CONTROL — IF EQUIPPED Located in the front storage area of the center console, this feature allows an iPod®/MP3 player, or an external USB device, to be connected to the audio system. 4 USB/AUX Ports 1 — USB Port 2 — AUX Port iPod® control supports Mini, 4G, Photo, Nano, 5G iPod® and iPhone® devices.
398 UNDERSTANDING YOUR INSTRUMENT PANEL may not fully support the iPod® control features. Please visit Apple’s website for software updates. For further information, refer to the Uconnect® User’s Manual. STEERING WHEEL AUDIO CONTROLS — IF EQUIPPED The remote sound system controls are located on the rear surface of the steering wheel. Reach behind the wheel to access the switches.
UNDERSTANDING YOUR INSTRUMENT PANEL 399 Pushing the center button will make the radio switch Media Mode between the various audio modes available (AM/FM/ Pushing the top of the switch once will go to the next SXM/AUX, etc.). track on the selected media (Disc, AUX, Bluetooth®). The left-hand control is a rocker-type switch with a Pushing the bottom of the switch once will go to the pushbutton in the center.
400 UNDERSTANDING YOUR INSTRUMENT PANEL antenna, it is recommended that the radio volume be CLIMATE CONTROLS turned down or off during mobile phone operation when The air conditioning and heating system is designed to not using Uconnect® (if equipped). make you comfortable in all types of weather. This system can be operated through either the controls on the General Information instrument panel or through the Uconnect® system disThis device complies with Part 15 of the FCC rules and play.
UNDERSTANDING YOUR INSTRUMENT PANEL 401 Front Blower Control There are seven blower speeds. Use this control to regulate the amount of air forced through the system in any mode you select. The blower speed increases as you move the control clockwise from the OFF position.
402 UNDERSTANDING YOUR INSTRUMENT PANEL Air Conditioning Operation Push the A/C button to engage the Air Conditioning (A/C). A LED will illuminate when the A/C system is engaged. Mode Control (Air Direction) Mode control allows you to choose from several patterns of air distribution. You can select either a primary MAX A/C mode, as identified by the symbols, or For maximum cooling, when MAX A/C is selected the a blend of two of these modes.
UNDERSTANDING YOUR INSTRUMENT PANEL 403 Bi-Level Mode Mix Mode Air is directed through the panel and floor outlets. Air is directed through the floor, defrost and side window demist outlets. This setting works best in cold or snowy conditions that require extra heat at the NOTE: There is a difference in temperature (in any windshield. This setting is good for maintaining comfort, conditions other than full cold or full hot), between the while reducing moisture on the windshield.
404 UNDERSTANDING YOUR INSTRUMENT PANEL Recirculation Control of moisture buildup inside the vehicle. For maximum defogging, select the outside air position. Push this button to choose between outside air intake or recirculation of the air inside the vehicle. A LED will • The A/C can be deselected manually without disturbilluminate when you are in Recirculation mode. Only use ing the mode control selection by pushing the A/C the Recirculation mode to temporarily block out any outbutton.
UNDERSTANDING YOUR INSTRUMENT PANEL 405 Rotate the temperature control knob to the desired tem- Manual Climate Controls With Touchscreen — If perature. Also, make sure to select only Panel, Bi-Level or Equipped Floor modes. Buttons On Your Uconnect® Faceplate Stop/Start System — If Equipped The buttons on the faceplate are located below the While in an Autostop, the Climate Controls system may Uconnect® screen. automatically adjust airflow to maintain cabin comfort.
406 UNDERSTANDING YOUR INSTRUMENT PANEL Buttons On Your Uconnect® Touchscreen Buttons on the touchscreen are accessible on the Uconnect® system screen. Uconnect® 8.4A/8.4AN Manual Temperature Controls — Buttons On The Touchscreen Uconnect® 5.0 Manual Temperature Controls — Buttons On The Touchscreen Button Descriptions (Applies To Both The Buttons On Your Faceplate And The Buttons On Your Touchscreen) 1. MAX A/C Button Press to change the current setting, the indicator illuminates when MAX A/C is ON.
UNDERSTANDING YOUR INSTRUMENT PANEL 407 again will cause the MAX A/C operation to switch into outlets. When the defrost button is selected, the blower manual mode and the MAX A/C indicator will turn off. level will increase. Use Defrost mode with maximum temperature settings for best windshield and side win2. A/C Button dow defrosting and defogging.
408 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! Failure to follow these cautions can cause damage to the heating elements: • Use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements. Labels can be peeled off after soaking with warm water. • Do not use scrapers, sharp instruments, or abrasive window cleaners on the interior surface of the window.
UNDERSTANDING YOUR INSTRUMENT PANEL 409 NOTE: BI-LEVEL mode is designed under comfort conditions to provide cooler air out of the panel outlets and The airflow distribution mode can be adjusted so air warmer air from the floor outlets. comes from the instrument panel outlets, floor outlets, • Floor Mode demist outlets and defrost outlets. The Mode settings are as follows: Air comes from the floor outlets. A slight amount 7.
410 UNDERSTANDING YOUR INSTRUMENT PANEL 8. Climate Control OFF Button Press this button to turn the Climate Control ON/OFF. 11. Temperature Control (Uconnect® 5.0) Press the temperature button on the touchscreen to regulate the temperature of the air inside the passenger 9. Temperature Control Down Button (Uconnect® 8.4) compartment. Moving the temperature bar into the red Provides temperature control. Press the button on the area, indicates warmer temperatures.
UNDERSTANDING YOUR INSTRUMENT PANEL 411 Automatic Climate Controls With Touchscreen — If Equipped Buttons On Your Uconnect® Faceplate Buttons On Your Uconnect® Touchscreen Buttons on your touchscreen are accessible on the Uconnect® system screen. 4 Uconnect® Automatic Climate Controls — Buttons On Your Faceplate Uconnect® 5.
412 UNDERSTANDING YOUR INSTRUMENT PANEL again will cause the MAX A/C operation to switch into manual mode and the MAX A/C indicator will turn off. 2. A/C Button Press to change the current setting, the indicator illuminates when A/C is ON. Performing this function again will cause the A/C operation to switch into manual mode and the A/C indicator will turn off. 3. Recirculation Button Press to change the current setting, the indicator illuminates when ON. Uconnect® 8.
UNDERSTANDING YOUR INSTRUMENT PANEL 413 5. Front Defrost Button Press to change the current airflow setting to Defrost mode. The indicator illuminates when this feature is ON. Air comes from the windshield and side window demist outlets. When the defrost button is selected, the blower level will increase. Use Defrost mode with maximum temperature settings for best windshield and side window defrosting and defogging. Performing this function will cause the ATC to switch into manual mode.
414 UNDERSTANDING YOUR INSTRUMENT PANEL Button slide the button on the touchscreen temperature bar towards the blue arrow button on the touchscreen for cooler temperature settings. Provides the passenger with independent temperature control. Press the button on the faceplate for warmer NOTE: Pressing this button while in Sync mode will temperature settings or on the touchscreen, press and automatically exit Sync. slide the button on the touchscreen temperature bar 9.
UNDERSTANDING YOUR INSTRUMENT PANEL 415 10. Blower Control 11. Modes Blower control is used to regulate the amount of air forced through the climate system. There are seven blower speeds available. Adjusting the blower will cause automatic mode to switch to manual operation.
416 UNDERSTANDING YOUR INSTRUMENT PANEL • Bi-Level Mode 12. Climate Control OFF Button Air comes from the instrument panel outlets and Press this button to turn the Climate Control ON/OFF. floor outlets. A slight amount of air is directed 13. Driver Temperature Control Down Button through the defrost and side window demister outlets. (Uconnect® 8.
UNDERSTANDING YOUR INSTRUMENT PANEL 417 the button on the touchscreen temperature bar towards system. When the air conditioning system is turned on, the red arrow button on the touchscreen for warmer cool dehumidified air will flow through the outlets into the cabin. For improved fuel economy, push the A/C temperature settings. button to turn off the air conditioning and manually NOTE: In Sync mode, this button will also automatically adjust the blower and airflow mode settings.
418 UNDERSTANDING YOUR INSTRUMENT PANEL recirculation LED will illuminate the button on your touchscreen and the button on your faceplate when either MAX A/C sets the control for maximum cooling perforbutton is selected. Push either button on your touchmance. screen or button on your faceplate a second time to turn Press to toggle between MAX A/C and the prior settings. off the Recirculation mode LED and allow outside air The button on the touchscreen illuminates when MAX into the vehicle. A/C is ON.
UNDERSTANDING YOUR INSTRUMENT PANEL 419 Automatic Temperature Control (ATC) NOTE: • It is not necessary to move the temperature settings for cold or hot vehicles. The system automatically adjusts 1. Push the AUTO button on your faceplate or the button the temperature, mode, and blower speed to provide on your touchscreen on the Automatic Temperature comfort as quickly as possible. Control (ATC) Panel. • The temperature can be displayed in U.S. or Metric 2.
420 UNDERSTANDING YOUR INSTRUMENT PANEL The blower fan speed can be set to any fixed speed by adjusting the blower control. The fan will now operate at a fixed speed until additional speeds are selected. This allows the front occupants to control the volume of air circulated in the vehicle and cancel the Auto mode. Summer Operation The engine cooling system must be protected with a high-quality antifreeze coolant to provide proper corrosion protection and to protect against engine overheating.
UNDERSTANDING YOUR INSTRUMENT PANEL 421 NOTE: Automatic Temperature Controls (ATC) will automatically adjust the climate control settings to reduce Any time you store your vehicle or keep it out of service or eliminate window fogging on the front windshield. (i.e., vacation) for two weeks or more, run the air When this occurs, recirculation will be unavailable. conditioning system at idle for about five minutes in fresh air with the blower setting in high.
422 UNDERSTANDING YOUR INSTRUMENT PANEL Control Setting Suggestions For Various Weather Conditions
UNDERSTANDING YOUR INSTRUMENT PANEL 423 Uconnect® VOICE RECOGNITION QUICK TIPS Introducing Uconnect® Start using Uconnect® Voice Recognition with these helpful quick tips. It provides the key Voice Commands and tips you need to know to control your Uconnect® 5.0 or 8.4A/8.4AN system. 4 Uconnect® 5.
424 UNDERSTANDING YOUR INSTRUMENT PANEL Get Started All you need to control your Uconnect® system with your voice are the buttons on your steering wheel. 1. Visit UconnectPhone.com to check mobile device and feature compatibility and to find phone pairing instructions. 2. Reduce background noise. Wind and passenger conversations are examples of noise that may impact recognition. 3. Speak clearly at a normal pace and volume while facing straight ahead.
UNDERSTANDING YOUR INSTRUMENT PANEL 425 4. Each time you give a Voice Command, you must first push either the VR or Phone button, wait until after the beep, then say your Voice Command. 5. You can interrupt the help message or system prompts by pushing the VR or Phone button and saying a Voice Command from current category. 4 Uconnect® Voice Command 1 — Push To Initiate Or To Answer A Phone Call, Send Or Receive A Text 2 — For all radios: Push To Begin Radio or Media functions. For 8.4A/8.
426 UNDERSTANDING YOUR INSTRUMENT PANEL Basic Voice Commands The basic Voice Commands below can be given at any point while using your Uconnect® system. Push the VR button . After the beep, sayѧ • Cancel to stop a current voice session • Help to hear a list of suggested Voice Commands • Repeat to listen to the system prompts again Notice the visual cues that inform you of your voice recognition system’s status. Cues appear on the touchscreen. Uconnect® 5.
UNDERSTANDING YOUR INSTRUMENT PANEL 427 Radio Use your voice to quickly get to the AM, FM or SiriusXM Satellite Radio® stations you would like to hear. (Subscription or included SiriusXM Satellite Radio® trial required.) Push the VR button . After the beep, sayѧ • Tune to ninety-five-point-five FM • Tune to Satellite Channel Hits 1 Uconnect® 8.4A/8.4AN TIP: At any time, if you are not sure of what to say or want to learn a Voice Command, press the VR button and say “Help.
428 UNDERSTANDING YOUR INSTRUMENT PANEL Uconnect® 5.0 Radio Uconnect® 8.4A/8.
UNDERSTANDING YOUR INSTRUMENT PANEL 429 TIP: Press the Browse button on the touchscreen to see all of the music on your iPod® or USB device. Your Voice Uconnect® offers connections via USB, SD, Bluetooth® Command must match exactly how the artist, album, and auxiliary ports (If Equipped). Voice operation is only song and genre information is displayed. available for connected USB and iPod® devices. (Remote CD player optional and not available on all vehicles.) Media .
430 UNDERSTANDING YOUR INSTRUMENT PANEL Phone Making and answering hands-free phone calls is easy with Uconnect®. When the Phonebook button is illuminated on your touchscreen, your system is ready. Check UconnectPhone.com for mobile phone compatibility and pairing instructions. . After the beep, say one of Push the Phone button the following commandsѧ • Call John Smith • Dial 123-456-7890 and follow the system prompts Uconnect® 8.4A/8.
UNDERSTANDING YOUR INSTRUMENT PANEL 431 TIP: When providing a Voice Command, push the and say “Call,” then pronounce the Phone button name exactly as it appears in your phone book. When a contact has multiple phone numbers, you can say “Call John Smith work.” 4 Uconnect® 8.4A/8.4AN Phone Uconnect® 5.
432 UNDERSTANDING YOUR INSTRUMENT PANEL Voice Text Reply Uconnect® will announce incoming text messages. Push and say Listen. (Must have comthe Phone button patible mobile phone paired to Uconnect® system.) 1. Once an incoming text message is read to you, push . After the beep, say: “Reply” the Phone button PRE-DEFINED VOICE TEXT REPLY RESPONSES I’ll call you I need See you in later. directions. of minutes. I’m on my way. Can’t talk right now. I’m lost. Thanks.
UNDERSTANDING YOUR INSTRUMENT PANEL 433 Push the VR button . After the beep, say one of the following commands: • Set temperature to 70 degrees • Set driver temperature to 70 degrees • Set passenger temperature to 70 degrees 4 TIP: Voice Command for Climate may only be used to adjust the interior temperature of your vehicle. Voice Command will not work to adjust the heated seats or steering wheel if equipped. Uconnect 8.4A/8.
434 UNDERSTANDING YOUR INSTRUMENT PANEL Navigation (8.4A/8.4AN) The Uconnect® navigation feature helps you save time and become more productive when you know exactly how to get to where you want to go. (Navigation is optional on the Uconnect® 8.4A system. See your dealer to activate navigation at any time.) 1. To enter a destination, push the VR button the beep, say: . After • For the 8.4A Uconnect® System, say: “Enter state.” • For the 8.
UNDERSTANDING YOUR INSTRUMENT PANEL 435 Uconnect® Access* (8.4A/8.4AN) Stolen Vehicle Assistance An included trial and/or subscription is required to take advantage of the Uconnect® Access services in the next section of this guide. To register with Uconnect® Access, press the Apps button on the 8.4-inch touchscreen to get started. Detailed registration instructions can be found on the next page.
436 UNDERSTANDING YOUR INSTRUMENT PANEL Register (8.4A/8.4AN) 1. Press the Apps button on the bottom of the 8.4-inch touchscreen. 2. If a pop-up message appears, press Register or go to the Favorite Apps menu and press Uconnect® Registration. 3. Read through the registration instructions. Enter and confirm your personal email address. Then press Send. 4. Check your personal inbox for an email from Uconnect® Access. 5.
UNDERSTANDING YOUR INSTRUMENT PANEL 437 Download the Uconnect® Access App to a compatible Securely link your mobile device to your vehicle with the Apple® or Android® mobile devices. All you need to do is: Uconnect® Access App. Once you have downloaded the 1. After registering with Uconnect® Access, log on to App, you may start your vehicle or lock it from virtually your Mopar® Owner Connect account at any distance. (Vehicle must be properly equipped with MoparOwnerConnect.
438 UNDERSTANDING YOUR INSTRUMENT PANEL Voice Texting (8.4A/8.4AN) TIP: 1. To send a message, push the Phone button . After • Not compatible with iPhone®. the beep, say the following command: “Send mes• Messages are limited to 140 characters. sage to John Smith” • The Messaging button on the touchscreen must be 2. Listen to the prompt. After the beep, dictate the illuminated to use the feature. message you would like to send. Wait for Uconnect® Yelp® (8.4A/8.4AN) to process your message. 3.
UNDERSTANDING YOUR INSTRUMENT PANEL 439 3. Press the “Yelp” button on the touchscreen. 4. Once the YELP® home screen appears on the touch, then say: “YELP screen, push the VR button search.” 5. Listen to the system prompts and after the beep, tell Uconnect® the place or business that you’d like Uconnect® to find. 4 TIP: Once you perform a search, you can reorganize the results by selecting either the Best Match, Rating or Distance tab on the top of the touchscreen display.
440 UNDERSTANDING YOUR INSTRUMENT PANEL SiriusXM Travel Link™ (8.4A/8.4AN) Need to find a gas station, view local movie listings, check a sports score or the 5 - day weather forecast? SiriusXM Travel Link™ is a suite of services that brings a wealth of information right to your Uconnect® 8.4AN system. (Not available for 8.4A system.) .
UNDERSTANDING YOUR INSTRUMENT PANEL 441 Additional Information Uconnect® System Support: © 2014 Chrysler Group LLC. All rights reserved. Mopar and Uconnect are registered trademarks and Mopar Owner Connect is a trademark of Chrysler Group LLC. Android is a trademark of Google Inc. SiriusXM and all related marks and logos are trademarks of SiriusXM Radio Inc. Yelp, Yelp logo, Yelp burst and related marks are registered trademarks of Yelp. • U.S. residents call 1-877-855-8400 DriveUconnect.
STARTING AND OPERATING CONTENTS 䡵 STARTING PROCEDURES . . . . . . . . . . . . . . . .448 ▫ Normal Starting. . . . . . . . . . . . . . . . . . . . . . .448 ▫ Extreme Cold Weather (Below –20°F Or −29°C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .449 ▫ Possible Reasons The Engine Does Not AUTOSTOP . . . . . . . . . . . . . . . . . . . . . . . . .452 ▫ To Start The Engine While In Autostop Mode . .453 ▫ To Manually Turn Off The Stop/Start System . .455 ▫ Extended Park Starting. . . . . . . . . .
444 STARTING AND OPERATING ▫ Brake/Transmission Shift Interlock System . . .459 䡵 ELECTRIC PARKING BRAKE (EPB) . . . . . . . . .475 ▫ Nine-Speed Automatic Transmission . . . . . . . .460 ▫ Auto Park Brake . . . . . . . . . . . . . . . . . . . . . .479 ▫ Gear Ranges . . . . . . . . . . . . . . . . . . . . . . . . .461 ▫ Safehold . . . . . . . . . . . . . . . . . . . . . . . . . . . .480 䡵 PADDLE SHIFT MODE — IF EQUIPPED . . . . .468 ▫ Brake Service Mode . . . . . . . . . . . . . . . . . . .
STARTING AND OPERATING 445 ▫ Rain Brake Support . . . . . . . . . . . . . . . . . . . .491 ▫ Tire Types . . . . . . . . . . . . . . . . . . . . . . . . . . .508 ▫ ESC Activation/Malfunction Indicator Light And ESC OFF Indicator Light . . . . . . . . . . . . . . . .491 ▫ Run Flat Tires — If Equipped . . . . . . . . . . . . .510 䡵 TIRE SAFETY INFORMATION . . . . . . . . . . . . .493 ▫ Tire Markings . . . . . . . . . . . . . . . . . . . . . . . .493 ▫ Tire Identification Number (TIN). . . . . . . . . . .
446 STARTING AND OPERATING 䡵 FUEL REQUIREMENTS . . . . . . . . . . . . . . . . . .531 ▫ Reformulated Gasoline . . . . . . . . . . . . . . . . .531 ▫ Gasoline/Oxygenate Blends . . . . . . . . . . . . . .532 ▫ E-85 Usage In Non-Flex Fuel Vehicles . . . . . . .532 ▫ MMT In Gasoline . . . . . . . . . . . . . . . . . . . . .533 ▫ Materials Added To Fuel . . . . . . . . . . . . . . . .533 ▫ Fuel System Cautions. . . . . . . . . . . . . . . . . . .534 ▫ Carbon Monoxide Warnings . . . . . . . . . . . . .
STARTING AND OPERATING 447 ▫ Towing This Vehicle Behind Another Vehicle . .545 ▫ Recreational Towing — Front-Wheel Drive (FWD) Models . . . . . . . . . . . . . . . . . . . . . . . . . . . .545 ▫ Recreational Towing — All-Wheel Drive (AWD) Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
448 STARTING AND OPERATING STARTING PROCEDURES WARNING! (Continued) Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. WARNING! • When leaving the vehicle, always remove the key fob from the ignition and lock your vehicle. • Never leave children alone in a vehicle, or with access to an unlocked vehicle. • Allowing children to be in a vehicle unattended is dangerous for a number of reasons.
STARTING AND OPERATING 449 within 10 seconds, cycle the ignition switch to the Extended Park Starting LOCK/OFF position, wait 10 to 15 seconds, then repeat NOTE: Extended Park condition occurs when the vehicle the “Normal Starting” procedure. has not been started or driven for at least 35 days. Tip Start Feature 1. Install a battery charger or jumper cables to the battery Cycle the ignition switch to START position and release it to ensure a full battery charge during the crank cycle.
450 STARTING AND OPERATING CAUTION! WARNING! (Continued) To prevent damage to the starter, do not continuously crank the engine for more than 10 seconds at a time. Wait 10 to 15 seconds before trying again. If Engine Fails To Start WARNING! • Never pour fuel or other flammable liquid into the throttle body air inlet opening in an attempt to start the vehicle. This could result in flash fire causing serious personal injury. (Continued) • Do not attempt to push or tow your vehicle to get it started.
STARTING AND OPERATING 451 With Tip Start After Starting If the engine fails to start after you have followed the ⬙Normal Starting⬙, “Extreme Cold Weather⬙ and ⬙Extended Park Starting⬙ procedures, it may be flooded. To clear any excess fuel, press the accelerator pedal all the way to the floor and hold it. Then, cycle the ignition switch to the START position and release it as soon as the starter engages. The starter motor will disengage automatically in 10 seconds.
452 STARTING AND OPERATING system will go into STOP/START READY and if all other The engine will shut down, the tachometer will move to conditions are met, can go into a STOP/START AU- the zero position and the Stop/Start telltale will illuminate indicating you are in Autostop. While in Autostop, the TOSTOP ACTIVE “Autostop” mode. Climate Controls system may automatically adjust airflow To Activate The Autostop Mode, The Following Must to maintain cabin comfort.
STARTING AND OPERATING 453 • Battery temperature is too warm or cold. Other Factors Which Can Inhibit Autostop Include: • The vehicle is on a steep grade. • Fuel level. • Cabin heating or cooling is in process and an accept- • Accelerator pedal input. able cabin temperature has not been achieved. • Engine temp too high. • HVAC is set to full defrost mode at a high blower It may be possible for the vehicle to be driven several speed.
454 STARTING AND OPERATING Conditions That Will Cause The Engine To Start Auto- Conditions That Force An Application Of The Electric matically While In Autostop Mode: Park Brake While In Autostop Mode: • The transmission selector is moved from DRIVE to • The driver door is open and brake pedal released. REVERSE. • The driver door is open and the driver seat belt is • To maintain cabin temperature comfort. unbuckled. • HVAC is set to full defrost mode. • The engine hood has been opened.
STARTING AND OPERATING 455 To Manually Turn Off The Stop/Start System 1. Press the STOP/START Off switch (located on the switch bank). The light on the switch will illuminate. Vehicle Information Center (EVIC)” or “Driver Information Display (DID)” in “Understanding Your Instrument Panel” for further information. 3. At the next vehicle stop (after turning off the STOP/ START system) the engine will not be stopped. 4.
456 STARTING AND OPERATING Information Center (EVIC)” or “Driver Information Dis- The engine block heater cord is routed under the hood, play (DID)” in “Understanding Your Instrument Panel” behind to the driver’s side headlamp. Follow the steps below to properly use the engine block heater: for further information. If the “SERVICE STOP/START SYSTEM” message ap- 1. Locate the engine block heater cord (behind the drivpears in the EVIC/DID, have the system checked by your er’s side headlamp).
STARTING AND OPERATING 457 NOTE: AUTOMATIC TRANSMISSION • The engine block heater cord is a factory installed option. If your vehicle is not equipped, heater cords are available from your authorized MOPAR® dealer. • The engine block heater will require 110 Volts AC and 6.5 Amps to activate the heater element. • The engine block heater must be plugged in at least one hour to have an adequate warming effect on the engine. WARNING! Remember to disconnect the engine block heater cord before driving.
458 STARTING AND OPERATING WARNING! WARNING! (Continued) • It is dangerous to shift out of PARK or NEUTRAL if the engine speed is higher than idle speed. If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in reverse. You could lose control of the vehicle and hit someone or something. Only shift into gear when the engine is idling normally and your foot is firmly pressing the brake pedal.
STARTING AND OPERATING 459 WARNING! (Continued) • Never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking brake, brake pedal or the transmission gear selector.
460 STARTING AND OPERATING Nine-Speed Automatic Transmission The transmission is controlled using a rotary electronic gear selector located on the center console. The transmission gear range (PRNDL/S) is displayed both above the gear selector and in the Electronic Vehicle Information Center (EVIC) or the Driver Information Display (DID). To select a gear range, simply rotate the gear selector. Push down on the gear selector and then rotate it, to access the L or S position.
STARTING AND OPERATING 461 Premium Shifter with Shift Paddles The premium transmission gear selector (with manual shift paddles mounted on the steering wheel) provides PARK, REVERSE, NEUTRAL, DRIVE, and SPORT shift positions. Manual shifts can be made using the shift paddles (refer to ⬙Paddle Shift Mode⬙ in this section).
462 STARTING AND OPERATING PARK (P) This range supplements the parking brake by locking the transmission. The engine can be started in this range. Never attempt to use PARK while the vehicle is in motion. Apply the parking brake when leaving the vehicle in this range. When parking on a level surface, you may shift the transmission into PARK first, and then apply the parking brake. When parking on a hill, apply the parking brake before shifting the transmission to PARK.
STARTING AND OPERATING 463 WARNING! (Continued) WARNING! (Continued) • Unintended movement of a vehicle could injure those in or near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, always apply the parking brake, shift the transmission into PARK, turn the engine OFF, and remove the key fob. When the ignition is in the OFF position, the transmission is locked in PARK, securing the vehicle against unwanted movement.
464 STARTING AND OPERATING CAUTION! • Before moving the transmission gear selector out of PARK, you must start the engine and also press the brake pedal. Otherwise, damage to the gear selector could result. • DO NOT race the engine when shifting from PARK or NEUTRAL into another gear range, as this can damage the drivetrain.
STARTING AND OPERATING 465 CAUTION! Towing the vehicle, coasting, or driving for any other reason with the transmission in NEUTRAL can cause severe transmission damage. Refer to “Recreational Towing” in “Starting And Operating” and “Towing A Disabled Vehicle” in “What To Do In Emergencies” for further information. winds), use the shift paddles (if equipped, refer to ⬙Paddle Shift Mode⬙ in this section for further information) or the LOW range (if equipped) to select a lower gear.
466 STARTING AND OPERATING During cold temperatures, transmission operation may be modified depending on engine and transmission temperature as well as vehicle speed. This feature improves warm up time of the engine and transmission to achieve maximum efficiency. Engagement of the torque converter clutch, and shifts into 8th or 9th gear, are inhibited until the transmission fluid is warm (refer to the “Note” under “Torque Converter Clutch” in this section).
STARTING AND OPERATING 467 In the event of a momentary problem, the transmission NOTE: Even if the transmission can be reset, we recomcan be reset to regain all forward gears by performing the mend that you visit your authorized dealer at your following steps: earliest possible convenience. Your authorized dealer has diagnostic equipment to determine if the problem could 1. Stop the vehicle. recur. If the transmission cannot be reset, authorized 2. Shift the transmission into PARK, if possible.
468 STARTING AND OPERATING NOTE: The torque converter clutch will not engage until the transmission fluid is warm (usually after 1 to 3 miles [2 to 5 km] of driving). Because the engine speed is higher when the torque converter clutch is not engaged, it may seem as if the transmission is not shifting properly when cold. This is normal. The torque converter clutch will function normally once the transmission is sufficiently warm.
STARTING AND OPERATING 469 result. It will remain in the selected gear until another upshift or downshift is chosen, except as described below. (to prevent engine lugging) and will display the current gear. Tapping the (+) paddle (at a stop) will allow starting in second gear. After a stop, the driver should manually upshift (+) the transmission as the vehicle accelerates. • If Paddle Shift is engaged while in DRIVE mode, the transmission will automatically shift up when maximum engine speed is reached.
470 STARTING AND OPERATING To disengage Paddle Shift mode, press and hold the (+) shift paddle until “D” or “S” is once again indicated in the instrument cluster. You can shift in or out of Paddle Shift mode at any time without taking your foot off the accelerator pedal. WARNING! Do not downshift for additional engine braking on a slippery surface. The drive wheels could lose their grip and the vehicle could skid, causing a collision or personal injury.
STARTING AND OPERATING 471 DRIVING ON SLIPPERY SURFACES Traction Acceleration When driving on wet or slushy roads, it is possible for a wedge of water to build up between the tire and road surface. This is hydroplaning and may cause partial or complete loss of vehicle control and stopping ability.
472 STARTING AND OPERATING DRIVING THROUGH WATER Shallow Standing Water Driving through water more than a few inches/ Although your vehicle is capable of driving through centimeters deep will require extra caution to ensure shallow standing water, consider the following Cautions safety and prevent damage to your vehicle. and Warnings before doing so. Flowing/Rising Water WARNING! Do not drive on or across a road or path where water is flowing and/or rising (as in storm run-off).
STARTING AND OPERATING 473 CAUTION! CAUTION! (Continued) • Always check the depth of the standing water before driving through it. Never drive through standing water that is deeper than the bottom of the tire rims mounted on the vehicle. • Determine the condition of the road or the path that is under water and if there are any obstacles in the way before driving through the standing water. • Do not exceed 5 mph (8 km/h) when driving through standing water. This will minimize wave effects.
474 STARTING AND OPERATING POWER STEERING The electric power steering system will give you good vehicle response and increased ease of maneuverability in tight spaces. The system will vary its assist to provide light efforts while parking and good feel while driving. If the electric steering system experiences a fault that reduces assist or prevents the vehicle from providing assist, you will still have the ability to steer the vehicle manually.
STARTING AND OPERATING 475 (EVIC)/Driver Information Display (DID)” in “Under- The parking brake is primarily intended to prevent the standing Your Instrument Panel” for further information. vehicle from rolling while parked. Before leaving the vehicle, make sure that the parking brake is applied. NOTE: Also, be certain to leave the transmission in PARK. • Even if the power steering assistance is no longer You can engage the parking brake in two ways; operational, it is still possible to steer the vehicle.
476 STARTING AND OPERATING on the brake pedal while you apply the parking brake, you may notice a small amount of brake pedal movement. The parking brake can be applied even when the ignition switch if OFF, however, it can only be released when the ignition switch in the RUN position. NOTE: The EPB fault lamp will illuminate if the EPB switch is held for longer than 20 seconds in either the released or applied position. The light will extinguish upon releasing the switch.
STARTING AND OPERATING 477 NOTE: When parking on a hill, it is important to turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade. Apply the parking brake before placing the shift lever in PARK, otherwise the load on the transmission locking mechanism may make it difficult to move the shift lever out of To release the parking brake manually, the ignition PARK. The parking brake should always be applied switch must be in the RUN position.
478 STARTING AND OPERATING WARNING! (Continued) WARNING! (Continued) • Never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking brake, brake pedal or the transmission gear selector.
STARTING AND OPERATING 479 If exceptional circumstances should make it necessary to engage the parking brake while the vehicle is in motion, maintain upward pressure on the electric parking brake switch for as long as engagement is desired. The BRAKE warning lamp will illuminate, and a continuous chime will sound. The rear stop lamps will also be illuminated automatically while the vehicle remains in motion. To disengage the parking brake while the vehicle is in motion, release the switch.
480 STARTING AND OPERATING Safehold Brake Service Mode Safehold is a safety feature of the Electric Park Brake System that will engage the park brake automatically if the vehicle is left unsecured. If the automatic transmission is not in PARK, the seat belt is unbuckled, the driver door is open, the vehicle is at a standstill, and there is no attempt to depress the brake pedal or accelerator pedal, the park brake will automatically engage to prevent the vehicle from rolling.
STARTING AND OPERATING 481 Service Mode has requirements that must be met in order to be activated: • The vehicle must be at a standstill. • The parking brake must be unapplied. • The transmission must be in Park or Neutral. WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.
482 STARTING AND OPERATING In the event power assist is lost for any reason (i.e., repeated brake applications with the engine off) the brakes will still function. However, the effort required to brake the vehicle will be much greater than that required with the power system operating. ELECTRONIC BRAKE CONTROL SYSTEM Your vehicle is equipped with an advanced electronic brake control system.
STARTING AND OPERATING 483 WARNING! (Continued) • The ABS cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded. • The ABS cannot prevent collisions, including those resulting from excessive speed in turns, following another vehicle too closely, or hydroplaning.
484 STARTING AND OPERATING When the vehicle is driven over 7 mph (11 km/h), you • A slight drop or fall away of the brake pedal at the end may hear a slight clicking sound as well as some related of the stop. motor noises. These noises are the system performing its These are all normal characteristics of ABS. self-check cycle to ensure that the ABS system is working properly. This self check occurs each time the vehicle is WARNING! started and accelerated past 7 mph (11 km/h).
STARTING AND OPERATING 485 Traction Control System (TCS) Electronic Roll Mitigation (ERM) This system monitors the amount of wheel spin of each of the driven wheels. If wheel spin is detected, brake pressure is applied to the slipping wheel(s) and engine power is reduced to provide enhanced acceleration and stability. A feature of the TCS system, Brake Limited Differential (BLD), functions similar to a limited slip differential and controls the wheel spin across a driven axle.
486 STARTING AND OPERATING WARNING! Many factors, such as vehicle loading, road conditions, and driving conditions, influence the chance that wheel lift or rollover may occur. ERM cannot prevent all wheel lift or rollovers, especially those that involve leaving the roadway or striking objects or other vehicles. The capabilities of an ERMequipped vehicle must never be exploited in a reckless or dangerous manner, which could jeopardize the user’s safety or the safety of others.
STARTING AND OPERATING 487 WARNING! (Continued) • The capabilities of a BAS-equipped vehicle must never be exploited in a reckless or dangerous manner, which could jeopardize the user’s safety or the safety of others. Electronic Stability Control (ESC) This system enhances directional control and stability of the vehicle under various driving conditions.
488 STARTING AND OPERATING WARNING! (Continued) from loss of vehicle control due to inappropriate driver input for the conditions. Only a safe, attentive, and skillful driver can prevent accidents. The capabilities of an ESC equipped vehicle must never be exploited in a reckless or dangerous manner which could jeopardize the user’s safety or the safety of others.
STARTING AND OPERATING 489 WARNING! When in “Partial Off” mode, the TCS functionality of ESC (except for the limited slip feature described in the TCS section) has been disabled and the “ESC Off Indicator Light” will be illuminated. When in “Partial Off” mode, the engine power reduction of TCS is disabled, and the enhanced vehicle stability offered by the ESC system is reduced.
490 STARTING AND OPERATING • Gear selection matches vehicle uphill direction (i.e., vehicle facing uphill is in forward gear; vehicle backThe HSA system is designed to assist the driver when ing uphill is in REVERSE gear). starting a vehicle from a stop on a hill. HSA will maintain the level of brake pressure the driver applied for a short HSA will work in REVERSE and all forward gears when period of time after the driver takes their foot off of the the activation criteria have been met.
STARTING AND OPERATING 491 HSA Off Rain Brake Support If you wish to turn off the HSA system, it can be done in the Uconnect® settings. Refer to ⬙Uconnect® Settings⬙ in ⬙Understanding Your Instrument Panel⬙ for further information. Rain Brake Support may improve braking performance in wet conditions. It will periodically apply a small amount of brake pressure to remove any water buildup on the front brake rotors.
492 STARTING AND OPERATING malfunction has been detected in the ESC system. If this NOTE: light remains on after several ignition cycles, and the • The “ESC Off Indicator Light” and the “ESC vehicle has been driven several miles (kilometers) at Activation/Malfunction Indicator Light” come on mospeeds greater than 30 mph (48 km/h), see your authomentarily each time the ignition switch is cycled ON. rized dealer as soon as possible to have the problem diagnosed and corrected.
STARTING AND OPERATING 493 TIRE SAFETY INFORMATION NOTE: Tire Markings • P (Passenger) — Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designation. Example: P215/65R15 95H. • European — Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter ⬙P⬙ is absent from this tire size designation.
494 STARTING AND OPERATING • Temporary spare tires are designed for temporary • High flotation tire sizing is based on U.S. design emergency use only. Temporary high pressure comstandards and it begins with the tire diameter molded pact spare tires have the letter “T” or “S” molded into into the sidewall. Example: 31x10.5 R15 LT. the sidewall preceding the size designation. Example: T145/80D18 103M.
STARTING AND OPERATING 495 EXAMPLE: R = Construction code – ⬙R⬙ means radial construction, or – ⬙D⬙ means diagonal or bias construction 15, 16, 18 = Rim diameter in inches (in) Service Description: 95 = Load Index – A numerical code associated with the maximum load a tire can carry H = Speed Symbol – A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions – The maximum speed corresponding to the speed symbol should only be
496 STARTING AND OPERATING EXAMPLE: Load Identification: Absence of the following load identification symbols on the sidewall of the tire indicates a Standard Load (SL) tire: • XL = Extra load (or reinforced) tire, or • LL = Light load tire or • C, D, E, F, G = Load range associated with the maximum load a tire can carry at a specified pressure Maximum Load – Maximum load indicates the maximum load this tire is designed to carry Maximum Pressure – Maximum pressure indicates the maximum permissible cold tir
STARTING AND OPERATING 497 EXAMPLE: DOT MA L9 ABCD 0301 DOT = Department of Transportation – This symbol certifies that the tire is in compliance with the U.S.
498 STARTING AND OPERATING Tire Terminology And Definitions Term B-Pillar Cold Tire Inflation Pressure Maximum Inflation Pressure Recommended Cold Tire Inflation Pressure Tire Placard Definition The vehicle B-Pillar is the structural member of the body located behind the front door. Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least three hours, or driven less than 1 mile (1.6 km) after sitting for a minimum of three hours.
STARTING AND OPERATING 499 Tire Loading And Tire Pressure Tire And Loading Information Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar or the rear edge of the driver’s side door.
500 STARTING AND OPERATING Tire And Loading Information Placard Example Tire Placard Location (B-Pillar) Tire And Loading Information Placard This placard tells you important information about the: 1. Number of people that can be carried in the vehicle. 2. Total weight your vehicle can carry.
STARTING AND OPERATING 501 To determine the maximum loading conditions of your vehicle, locate the statement “The combined weight of 4. Cold tire inflation pressures for the front, rear, and occupants and cargo should never exceed XXX lbs or spare tires. XXX kg” on the Tire and Loading Information placard. The combined weight of occupants, cargo/luggage and Loading trailer tongue weight (if applicable) should never exceed The vehicle maximum load on the tire must not exceed the weight referenced here.
502 STARTING AND OPERATING 4. The resulting figure equals the available amount of NOTE: cargo and luggage load capacity. For example, if • If your vehicle will be towing a trailer, load from your “XXX” amount equals 1,400 lbs (635 kg) and there will trailer will be transferred to your vehicle.
STARTING AND OPERATING 503 5
504 STARTING AND OPERATING WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.
STARTING AND OPERATING 505 WARNING! (Continued) • Unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • Always drive with each tire inflated to the recommended cold tire inflation pressure. Economy Under-inflated tires will increase tire rolling resistance resulting in higher fuel consumption.
506 STARTING AND OPERATING Tire Inflation Pressures The proper cold tire inflation pressure is listed on the driver’s side B-Pillar or rear edge of the driver’s side door. At least once a month: Inflation pressures specified on the placard are always “cold tire inflation pressure.” Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least three hours, or driven less than 1 mile (1.6 km) after sitting for a minimum of three hours.
STARTING AND OPERATING 507 inflation pressure should be increased by 3 psi (21 kPa), which equals 1 psi (7 kPa) for every 12°F (7°C) for this outside temperature condition. Tire pressure may increase from 2 to 6 psi (13 to 40 kPa) during operation. DO NOT reduce this normal pressure build up or your tire pressure will be too low. Tire Pressures For High Speed Operation WARNING! High speed driving with your vehicle under maximum load is dangerous. The added strain on your tires could cause them to fail.
508 STARTING AND OPERATING Tire Repair Tire Types If your tire becomes damaged, it may be repaired if it All Season Tires — If Equipped meets the following criteria: All Season tires provide traction for all seasons (spring, summer, fall and winter). Traction levels may vary be• The tire has not been driven on when flat. tween different all season tires.
STARTING AND OPERATING 509 Use summer tires only in sets of four; failure to do so may Snow Tires adversely affect the safety and handling of your vehicle. Some areas of the country require the use of snow tires during the winter. Snow tires can be identified by a WARNING! “mountain/snowflake” symbol on the tire sidewall. Do not use summer tires in snow/ice conditions. You could lose vehicle control, resulting in severe injury or death.
510 STARTING AND OPERATING While studded tires improve performance on ice, skid and traction capability on wet or dry surfaces may be poorer than that of non-studded tires. Some states prohibit studded tires; therefore, local laws should be checked before using these tire types. Run Flat Tires — If Equipped Run Flat tires allow you the capability to drive 50 miles (80 km) at 50 mph (80 km/h) after a rapid loss of inflation pressure. This rapid loss of inflation is referred to as the Run Flat mode.
STARTING AND OPERATING 511 Spare Tire Matching Original Equipped Tire And Wheel — If Equipped Your vehicle may be equipped with a spare tire and wheel equivalent in look and function to the original equipment tire and wheel found on the front or rear axle of your vehicle. This spare tire may be used in the tire rotation for your vehicle. If your vehicle has this option, refer to an authorized tire dealer for the recommended tire rotation pattern.
512 STARTING AND OPERATING your original equipment tire, replace (or repair) the original equipment tire and reinstall on the vehicle at the The full size spare is for temporary emergency use only. first opportunity. This tire may look like the originally equipped tire on the front or rear axle of your vehicle, but it is not. This spare WARNING! tire may have limited tread life. When the tread is worn to the tread wear indicators, the temporary use full size Limited-use spares are for emergency use only.
STARTING AND OPERATING 513 Tire Spinning Tread Wear Indicators When stuck in mud, sand, snow, or ice conditions, do not Tread wear indicators are in the original equipment tires spin your vehicle’s wheels above 30 mph (48 km/h) or to help you in determining when your tires should be for longer than 30 seconds continuously without stop- replaced. ping. Refer to “Freeing A Stuck Vehicle” in “What To Do In Emergencies” for further information. WARNING! Fast spinning tires can be dangerous.
514 STARTING AND OPERATING These indicators are molded into the bottom of the tread • Distance driven grooves. They will appear as bands when the tread depth • Performance tires, tires with a speed rating of V or becomes 1/16” (2 mm). When the tread is worn to the higher, and summer tires typically have a reduced tread wear indicators, the tire should be replaced. Refer tread life.
STARTING AND OPERATING 515 It is recommended to replace the two front tires or two rear tires as a pair. Replacing just one tire can seriously The tires on your new vehicle provide a balance of many affect your vehicle’s handling. If you ever replace a characteristics. They should be inspected regularly for wheel, make sure that the wheel’s specifications match wear and correct cold tire inflation pressures. The manuthose of the original wheels.
516 STARTING AND OPERATING WARNING! WARNING! (Continued) • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle. This can cause unpredictable handling and stress to steering and suspension components. You could lose control and have a collision resulting in serious injury or death.
STARTING AND OPERATING 517 • Install on front tires only. • For a 215/55R17 tire on a 17 x 7.0J x 41mm wheel, use of a snow traction device with a maximum projection of 9 mm beyond the tire profile is recommended. WARNING! Using tires of different size and type (M+S, Snow) between front and rear axles can cause unpredictable handling. You could lose control and have a collision.
518 STARTING AND OPERATING CAUTION! (Continued) • Observe the traction device manufacturer’s instructions on the method of installation, operating speed, and conditions for use. Always use the suggested operating speed of the device manufacturer’s if it is less than 30 mph (48 km/h). • Do not use traction devices on a compact spare tire. TIRE ROTATION RECOMMENDATIONS These effects can be reduced by timely rotation of tires.
STARTING AND OPERATING 519 TIRE PRESSURE MONITOR SYSTEM (TPMS) The Tire Pressure Monitor System (TPMS) will warn the driver of a low tire pressure based on the vehicle recommended cold placard pressure. Tire Rotation The tire pressure will vary with temperature by about 1 psi (7 kPa) for every 12°F (6.5°C). This means that when the outside temperature decreases, the tire pressure will decrease. Tire pressure should always be set based on cold inflation tire pressure.
520 STARTING AND OPERATING also increase as the vehicle is driven. This is normal and NOTE: When filling warm tires, the tire pressure may there should be no adjustment for this increased pres- need to be increased up to an additional 4 psi (30 kPa) above the recommended cold placard pressure in order sure. to turn the Tire Pressure Monitoring Telltale Light off.
STARTING AND OPERATING 521 but the “Tire Pressure Monitoring Telltale Light” will still be on. In this situation, the “Tire Pressure Monitoring Telltale Light” will turn off only after the tires are inflated to the vehicle’s recommended cold placard pressure value. NOTE: When filling warm tires, the tire pressure may need to be increased up to an additional 4 psi (30 kPa) above the recommended cold placard pressure in order to turn the Tire Pressure Monitoring Telltale Light off.
522 STARTING AND OPERATING CAUTION! (Continued) • After inspecting or adjusting the tire pressure, always reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the Tire Pressure Monitoring Sensor. • Driving on a significantly underinflated tire causes the tire to overheat and can lead to tire failure. Underinflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability.
STARTING AND OPERATING 523 Base System Tire Pressure Monitoring Low Pressure Warnings The Tire Pressure Monitor System (TPMS) uses wireless The “Tire Pressure Monitoring Telltale Light” will technology with wheel rim mounted electronic sensors to illuminate in the instrument cluster, a “LOW TIRE monitor tire pressure levels.
524 STARTING AND OPERATING NOTE: When filling warm tires, the tire pressure may 1. Jamming due to electronic devices or driving next to facilities emitting the same radio frequencies as the need to be increased up to an additional 4 psi (30 kPa) TPMS sensors. above the recommended cold placard pressure in order to turn the Tire Pressure Monitoring Telltale Light off. 2. Installing some form of aftermarket window tinting The vehicle may need to be driven for up to 20 minutes that affects radio wave signals.
STARTING AND OPERATING 525 Telltale Light” and “LOW TIRE PRESSURE” and ⬙Inflate to XX⬙ messages will turn on upon the next ignition cycle. sound and the “TPMS Telltale Light” and “LOW TIRE PRESSURE” and ⬙Inflate to XX⬙ messages will turn on upon the next ignition cycle. 3. Driving the vehicle for up to 20 minutes above 15 mph 3.
526 STARTING AND OPERATING Premium System — If Equipped The Tire Pressure Monitor System (TPMS) uses wireless technology with wheel rim mounted electronic sensors to monitor tire pressure levels. Sensors, mounted to each wheel as part of the valve stem, transmit tire pressure readings to the receiver module. The matching full size spare wheel and tire assembly (if equipped) has a tire pressure monitoring sensor. The full size spare can be used in place of any of the four road tires.
STARTING AND OPERATING 527 update, the pressure values in the graphic display in the DID will return to their original color, and the “Tire Pressure Monitoring Telltale Light” will turn off. The vehicle may need to be driven for up to 20 minutes above 15 mph (24 km/h) in order for the TPMS to receive this information. SERVICE TPMS Warning When a system fault is detected, the “Tire Pressure Monitoring Telltale Light” will flash on and off for 75 seconds and then remain on solid.
528 STARTING AND OPERATING message will no longer display, and a pressure value will display in place of the dashes. A system fault can occur due to any of the following: 1. Jamming due to electronic devices or driving next to facilities emitting the same radio frequencies as the TPMS sensors. 2. Installing some form of aftermarket window tinting that affects radio wave signals. 3. Lots of snow or ice around the wheels or wheel housings. Tire Pressure Monitoring Service Warning 4.
STARTING AND OPERATING 529 4. The DID will display a graphic showing the tire pressure value in the same color as the other pressure 1. The matching full size spare wheel and tire assembly values in place of the different color low tire pressure has a tire pressure monitoring sensor that can be value. The DID will also display a “SPARE LOW monitored by the TPMS. PRESSURE” message to remind you to service the flat 2. If you install the full size spare in place of a road tire tire.
530 STARTING AND OPERATING low-pressure warning limit in any of the four active 3. After driving the vehicle for up to 20 minutes above road tires. The vehicle may need to be driven for up to 15 mph (24 km/h), the “TPMS Telltale Light” will 20 minutes above 15 mph (24 km/h) in order for the flash on and off for 75 seconds and then remain on TPMS to receive this information. solid.
STARTING AND OPERATING 531 FUEL REQUIREMENTS Over 40 auto manufacturers worldwide have issued and endorsed consistent gasoline specifications (the Worldwide Fuel Charter, WWFC) which define fuel properties necessary to deliver enhanced emissions, performance, and durability for your vehicle. The manufacturer recommends the use of gasoline that meet the WWFC specifications if they are available.
532 STARTING AND OPERATING Gasoline/Oxygenate Blends E-85 Usage In Non-Flex Fuel Vehicles Some fuel suppliers blend unleaded gasoline with oxy- Non-Flex Fuel Vehicles (FFV) are compatible with gasogenates such as Ethanol. Fuels blended with oxygenates line containing 10% ethanol (E10). Gasoline with higher may be used in your vehicle. ethanol content may void the New Vehicle Limited Warranty. CAUTION! DO NOT use gasoline containing Methanol or gasoline containing more than 10% Ethanol.
STARTING AND OPERATING 533 To fix a Non-FFV vehicle inadvertently fueled once with life and reduces emissions system performance in some vehicles. The manufacturer recommends that gasoline E-85 perform the following: without MMT be used in your vehicle. The MMT content • Drain the fuel tank (see your authorized dealer). of gasoline may not be indicated on the gasoline pump, therefore, you should ask your gasoline retailer whether • Change the engine oil and oil filter. the gasoline contains MMT.
534 STARTING AND OPERATING Fuel System Cautions CAUTION! (Continued) CAUTION! Follow these guidelines to maintain your vehicle’s performance: • The use of leaded gas is prohibited by Federal law. Using leaded gasoline can impair engine performance and damage the emissions control system. • An out-of-tune engine or certain fuel or ignition malfunctions can cause the catalytic converter to overheat.
STARTING AND OPERATING 535 Carbon Monoxide Warnings WARNING! (Continued) WARNING! Carbon monoxide (CO) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • Do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas, which can kill. Never run the engine in a closed area, such as a garage, and never sit in a parked vehicle with the engine running for an extended period.
536 STARTING AND OPERATING E-85 Fuel Cap E-85 Badge
STARTING AND OPERATING 537 For best results, a refueling pattern that avoids alternating between E-85 and unleaded gasoline is recomE-85 is a mixture of approximately 85% fuel ethanol and mended. 15% unleaded gasoline. When you do switch fuel types it is recommended that: Ethanol Fuel (E-85) WARNING! Ethanol vapors are extremely flammable and could cause serious personal injury.
538 STARTING AND OPERATING • Some additives used in regular gasoline are not fully compatible with E-85 and may form deposits in your engine. To eliminate driveability issues that may be caused by these deposits, a supplemental gasoline additive, such as MOPAR® Injector Cleanup or Techron may be used. Selection Of Engine Oil For Flexible Fuel Vehicles (E-85) And Gasoline Vehicles FFV vehicles operated on E-85 require specially formulated engine oils.
STARTING AND OPERATING 539 Replacement Parts ADDING FUEL Many components in your Flexible Fuel Vehicle (FFV) are designed to be compatible with ethanol. Always be sure that your vehicle is serviced with correct ethanol compatible parts. The fuel filler cap is located behind the fuel filler door, on the passenger side of the vehicle. If the fuel filler cap is lost or damaged, be sure the replacement fuel filler cap has been designed for use with this vehicle.
540 STARTING AND OPERATING WARNING! CAUTION! • Never have any smoking materials lit in or near the vehicle when the gas cap is removed or the tank is being filled. • Never add fuel when the engine is running. This is in violation of most state and federal fire regulations and may cause the MIL to turn on. • A fire may result if gasoline is pumped into a portable container that is inside of a vehicle. You could be burned. Always place gas containers on the ground while filling.
STARTING AND OPERATING 541 4. After you have stopped pumping fuel, remove the fuel filler nozzle and replace the fuel filler cap. 5. To close the fuel filler door, press the center-rear edge (9 o’clock position) of the fuel filler door and then release. The fuel filler door will latch closed. NOTE: • In certain cold conditions, ice may prevent the fuel filler door from opening. If this occurs, lightly push on the fuel filler door around the perimeter to break the ice build up.
542 STARTING AND OPERATING • If the fuel filler cap is not tightened properly, the MIL VEHICLE LOADING will come on. Be sure the fuel filler cap is tightened Certification Label every time the vehicle is refueled. As required by National Highway Traffic Safety AdminLoose Fuel Filler Cap Message istration regulations, your vehicle has a certification label If the vehicle diagnostic system determines that the fuel affixed to the driver’s side door or pillar.
STARTING AND OPERATING 543 Payload Rim Size The payload of a vehicle is defined as the allowable load This is the rim size that is appropriate for the tire size weight a truck can carry, including the weight of the listed. driver, all passengers, options and cargo. Inflation Pressure Gross Axle Weight Rating (GAWR) This is the cold tire inflation pressure for your vehicle for The GAWR is the maximum permissible load on the front all loading conditions up to full GAWR. and rear axles.
544 STARTING AND OPERATING Improper weight distributions can have an adverse effect on the way your vehicle steers and handles and the way The actual total weight and the weight of the front and the brakes operate. rear of your vehicle at the ground can best be determined by weighing it when it is loaded and ready for operation. Loading CAUTION! The entire vehicle should first be weighed on a commercial scale to insure that the GVWR has not been exceeded.
STARTING AND OPERATING 545 RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) 4. Properly secure the front wheels to the dolly, following the dolly manufacturer’s instructions. Towing This Vehicle Behind Another Vehicle 5. Release the parking brake. Recreational Towing — Front-Wheel Drive (FWD) Models DO NOT flat tow this vehicle. Damage to the drivetrain will result. Recreational towing for front-wheel drive models is allowed ONLY if the front wheels are OFF the ground.
546 STARTING AND OPERATING Recreational Towing — All-Wheel Drive (AWD) Models Recreational towing is not allowed. These models do not have a NEUTRAL (N) position in the power transfer unit. NOTE: This vehicle may be towed on a flatbed or vehicle trailer provided all four wheels are OFF the ground. CAUTION! Towing this vehicle with ANY of its wheels on the ground can cause severe transmission and/or power transfer unit damage.
WHAT TO DO IN EMERGENCIES CONTENTS 䡵 HAZARD WARNING FLASHERS . . . . . . . . . . .549 䡵 JACKING AND TIRE CHANGING . . . . . . . . . .562 䡵 IF YOUR ENGINE OVERHEATS . . . . . . . . . . . .549 ▫ Jack Location/Spare Tire Stowage . . . . . . . . .563 䡵 WHEEL AND TIRE TORQUE SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . .550 ▫ Preparations For Jacking . . . . . . . . . . . . . . . .565 ▫ Torque Specifications . . . . . . . . . . . . . . . . . . .550 䡵 TIRE SERVICE KIT — IF EQUIPPED . . . . . . . .
548 WHAT TO DO IN EMERGENCIES 䡵 TOWING A DISABLED VEHICLE . . . . . . . . . . .584 ▫ Front-Wheel Drive (FWD) Models . . . . . . . . .585 ▫ All-Wheel Drive (AWD) Models . . . . . . . . . . .
WHAT TO DO IN EMERGENCIES 549 HAZARD WARNING FLASHERS IF YOUR ENGINE OVERHEATS The Hazard Warning flasher switch is located in the In any of the following situations, you can reduce the switch bank below the radio screen. potential for overheating by taking the appropriate action. Press the switch to turn on the Hazard Warning • On the highways — slow down. flasher.
550 WHAT TO DO IN EMERGENCIES CAUTION! Driving with a hot cooling system could damage your vehicle. If the temperature gauge reads “H,” pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the “H,” turn the engine off immediately and call for service. WHEEL AND TIRE TORQUE SPECIFICATIONS Proper lug nut/bolt torque is very important to ensure that the wheel is properly mounted to the vehicle.
WHAT TO DO IN EMERGENCIES 551 6 Wheel Mounting Surface Torque Patterns Tighten the lug nuts/bolts in a star pattern until each After 25 miles (40 km) check the lug nut/bolt torque to be nut/bolt has been tightened twice. sure that all the lug nuts/bolts are properly seated against the wheel.
552 WHAT TO DO IN EMERGENCIES WARNING! To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle has been lowered. Failure to follow this warning may result in personal injury. Tire Service Kit Storage The Tire Service Kit is stowed under an access cover in the trunk. 1. Open the trunk. 2. Lift the access cover using the pull strap. TIRE SERVICE KIT — IF EQUIPPED Small punctures up to ¼” (6 mm) in the tire tread can be sealed with Tire Service Kit.
WHAT TO DO IN EMERGENCIES 553 3. Remove the fastener securing the Tire Service Kit. 4. Remove Tire Service Kit.
554 WHAT TO DO IN EMERGENCIES Tire Service Kit Components And Operation Tire Service Kit Usage Precautions • Replace the Tire Service Kit Sealant Bottle (1) and Sealant Hose (6) prior to the expiration date (printed at the lower right hand corner on the bottle label) to assure optimum operation of the system. Refer to “Sealing a Tire with Tire Service Kit” section (F) “Sealant Bottle and Hose Replacement”.
WHAT TO DO IN EMERGENCIES 555 from the vehicle or tire and wheel components. Once the sealant dries, it can easily be peeled off and properly discarded. • For optimum performance, make sure the valve stem on the wheel is free of debris before connecting the Tire Service Kit. • You can use the Tire Service Kit air pump to inflate bicycle tires.
556 WHAT TO DO IN EMERGENCIES WARNING! WARNING! (Continued) • Do not attempt to seal a tire on the side of the vehicle closest to traffic. Pull far enough off the road to avoid the danger of being hit when using the Tire Service Kit. • Do not use Tire Service Kit or drive the vehicle under the following circumstances: – If the puncture in the tire tread is approximately 1/4” (6 mm) or larger. – If the tire has any sidewall damage.
WHAT TO DO IN EMERGENCIES 557 WARNING! (Continued) • Tire Service Kit Sealant solution contains latex. In case of an allergic reaction or rash, consult a physician immediately. Keep Tire Service Kit out of reach of children. If swallowed, rinse mouth immediately with plenty of water and drink plenty of water. Do not induce vomiting! Consult a physician immediately. Sealing A Tire With Tire Service Kit (A) Whenever You Stop To Use Tire Service Kit: on the ground.
558 WHAT TO DO IN EMERGENCIES 4. Remove the cap from the valve stem and then screw NOTE: Sealant may leak out through the puncture in the the fitting at the end of the Sealant Hose (6) onto the tire. valve stem. If the sealant (white fluid) does not flow within 0 – 10 5. Uncoil the Power Plug (8) and insert the plug into the seconds through the Sealant Hose (6): vehicle’s 12 Volt power outlet. 1. Press the Power Button (4) to turn Off the Tire Service NOTE: Do not remove foreign objects (e.g.
WHAT TO DO IN EMERGENCIES 559 NOTE: If the Mode Select Knob (5) is on Air Mode and If the tire does not inflate to at least 26 psi (1.8 Bar) the pump is operating, air will dispense from the Air pressure within 15 minutes: Pump Hose (7) only, not the Sealant Hose (6). • The tire is too badly damaged. Do not attempt to drive the vehicle further. Call for assistance. If the sealant (white fluid) does flow through the Sealant Hose (6): NOTE: If the tire becomes over-inflated, press the Defla1.
560 WHAT TO DO IN EMERGENCIES hose, and place the Tire Service Kit in the vehicle storage location. Quickly proceed to (D) “Drive Vehicle.” CAUTION! • The metal end fitting from Power Plug (8) may get hot after use, so it should be handled carefully. • Failure to reinstall the cap on the fitting at the end of the Sealant Hose (6) can result in sealant contacting your skin, clothing, and the vehicle’s interior.
WHAT TO DO IN EMERGENCIES 561 3. Uncoil the Air Pump Hose (7) (black in color) and 2. Disconnect the Tire Service Kit from the valve stem, screw the fitting at the end of hose (7) onto the valve reinstall the cap on the valve stem and unplug from 12 Volt outlet. stem. 4. Check the pressure in the tire by reading the Pressure 3. Place the Tire Service Kit in its proper storage area in Gauge (3). the vehicle. 4.
562 WHAT TO DO IN EMERGENCIES (F) Sealant Bottle And Hose Replacement: 1. Uncoil the Sealant Hose (6) (clear in color). 6. Verify that the cap is installed on the fitting at the end of the Sealant Hose (6) and return the hose to its storage area (located on the bottom of the air pump). 2. Locate the round Sealant Bottle release button in the 7. Return the Tire Service Kit to its storage location in the recessed area under the sealant bottle. vehicle. 3. Press the Sealant Bottle release button.
WHAT TO DO IN EMERGENCIES 563 WARNING! (Continued) • Being under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never put any part of your body under a vehicle that is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift. • Never start or run the engine while the vehicle is on a jack. • The jack is designed to be used as a tool for changing tires only.
564 WHAT TO DO IN EMERGENCIES Pull Strap Jack And Spare Tire Fastener 3. Remove the fastener securing the jack and spare tire. 4. Remove the scissors jack, wheel bolt wrench and wheel chocks from the spare wheel as an assembly. Remove the chocks from the jack assembly. Turn the jack screw to the left to loosen the wheel bolt wrench, and remove the wrench from the jack assembly.
WHAT TO DO IN EMERGENCIES 565 5. Remove the spare tire. WARNING! A loose tire or jack thrown forward in a collision or hard stop could endanger the occupants of the vehicle. Always stow the jack parts and the spare tire in the places provided. Have the deflated (flat) tire repaired or replaced immediately.
566 WHAT TO DO IN EMERGENCIES Jacking Instructions WARNING! (Continued) WARNING! Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: • Always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle. • Turn on the Hazard Warning flasher. • Chock the wheel diagonally opposite the wheel to be raised. • Set the parking brake firmly and set an automatic transmission in PARK.
WHAT TO DO IN EMERGENCIES 567 Jack Warning Label CAUTION! Do not attempt to raise the vehicle by jacking on locations other than those indicated in the Jacking Instructions for this vehicle. 6 Jacking Locations 1. Remove the spare tire, jack, and wheel bolt wrench. NOTE: The jack handle attaches to the side of the jack with two attachment points. When the jack is partially expanded, the tension between the two attachment points holds the jack handle in place.
568 WHAT TO DO IN EMERGENCIES wheel with the flat tire. Turn the wheel bolts counterclockwise one turn while the wheel is still on the ground. 4. Place the jack underneath the notched lift area that is closest to the flat tire. Removing Jack Handle From Jack 2. If equipped with aluminum wheels where the center cap covers the wheel bolts, use the wheel bolt wrench to pry the center cap off carefully before raising the vehicle. 3.
WHAT TO DO IN EMERGENCIES 569 6 Rear Body Flange Front Body Flange Engaged
570 WHAT TO DO IN EMERGENCIES Rear Body Flange Engaged 5. Turn the jack screw clockwise to firmly engage the jack saddle with the lift area of the sill flange, centering the jack saddle between the locating notches on the sill flange. 6. Raise the vehicle just enough to remove the flat tire and install the spare tire.
WHAT TO DO IN EMERGENCIES 571 WARNING! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 7. Remove the wheel bolts and tire. 8. Mount the spare tire. CAUTION! Rear Jacking Location Be sure to mount the spare tire with the valve stem facing outward. The vehicle could be damaged if the spare tire is mounted incorrectly.
572 WHAT TO DO IN EMERGENCIES NOTE: • For vehicles so equipped, do not attempt to install a center cap or wheel cover on the compact spare. • Refer to “Compact Spare Tire” and to “Limited-Use Spare” under “Tires—General Information” in “Starting and Operating” for additional warnings, cautions, and information about the spare tire, its use, and operation. Mounting Spare Tire 9. Install the wheel bolts with the threaded end of the wheel bolt toward the wheel. Lightly tighten the wheel bolts.
WHAT TO DO IN EMERGENCIES 573 10. Lower the vehicle to the ground by turning the jack handle counterclockwise. WARNING! 11. Finish tightening the wheel bolts. Push down on the A loose tire or jack thrown forward in a collision or wrench while at the end of the handle for increased hard stop could endanger the occupants of the veleverage. Tighten the wheel bolts in a star pattern hicle. Always stow the jack parts and the spare tire in until each wheel bolt has been tightened twice.
574 WHAT TO DO IN EMERGENCIES snapping the cover over the two wheel bolts. Do not use a hammer or excessive force to install the cover. 4. Install the remaining wheel bolts with the threaded end of the wheel bolt toward the wheel. Lightly tighten the wheel bolts.
WHAT TO DO IN EMERGENCIES 575 “Torque Specifications” in this section for proper lug bolt torque. If in doubt about the correct tightness, have them checked with a torque wrench by your authorized dealer or service station. WARNING! To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle has been lowered. Failure to follow this warning may result in personal injury. 7. Lower the jack until it is free. Remove the wheel chocks.
576 WHAT TO DO IN EMERGENCIES 5. Lower the jack until it is free. Remove the wheel chocks. Reassemble the lug wrench to the jack assembly and stow it in the spare tire area. Secure the assembly using the means provided. Release the parking brake before driving the vehicle. 6. After 25 miles (40 km) check the wheel bolt torque with a torque wrench to ensure that all wheel bolts are properly seated against the wheel.
WHAT TO DO IN EMERGENCIES 577 WARNING! 1 — Positive Battery Post 2 — Negative Battery Post • Take care to avoid the radiator cooling fan whenever the hood is raised. It can start anytime the ignition switch is ON. You can be injured by moving fan blades. • Remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact. You could be seriously injured.
578 WHAT TO DO IN EMERGENCIES 3. If using another vehicle to jump-start the battery, park the vehicle within the jumper cables reach, set the parking brake and make sure the ignition is OFF. WARNING! Do not allow vehicles to touch each other as this could establish a ground connection and personal injury could result. Jump-Starting Procedure WARNING! Failure to follow this jump-starting procedure could result in personal injury or property damage due to battery explosion.
WHAT TO DO IN EMERGENCIES 579 WARNING! Do not connect the jumper cable to the negative (-) post of the discharged battery. The resulting electrical spark could cause the battery to explode and could result in personal injury. Only use the specific ground point, do not use any other exposed metal parts. 2. Disconnect the opposite end of the negative (-) jumper cable from the negative (-) post of the booster battery. 3.
580 WHAT TO DO IN EMERGENCIES CAUTION! (Continued) the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting. Use the least amount of accelerator pedal pressure that will maintain the rocking motion without spinning the wheels or racing the engine. NOTE: Press the ⬙ESC Off⬙ switch to place the Electronic Stability Control (ESC) system in ⬙Partial Off⬙ mode, before rocking the vehicle.
WHAT TO DO IN EMERGENCIES 581 CAUTION! WARNING! (Continued) • When “rocking” a stuck vehicle by shifting between DRIVE and REVERSE, do not spin the wheels faster than 15 mph (24 km/h), or drivetrain damage may result. • Revving the engine or spinning the wheels too fast may lead to transmission overheating and failure. It can also damage the tires. Do not spin the wheels above 30 mph (48 km/h) while in gear (no transmission shifting occurring). explode and injure someone.
582 WHAT TO DO IN EMERGENCIES In order to move the vehicle in cases where the transmis- 2. Using a small screwdriver or similar tool, remove the sion will not shift out of PARK (such as a dead battery), Manual Park Release access cover, which is undera Manual Park Release is available. neath the rubber storage bin liner in the center console pass-through. Follow these steps to activate the Manual Park Release: 1. Firmly apply the parking brake. Manual Park Release Cover Manual Park Release location 3.
WHAT TO DO IN EMERGENCIES 583 6 Manual Park Release Tether Locked Position 4. Pull the tether to rotate the lever up and rearward, 5. The vehicle is now out of PARK and can be towed. until it locks vertically in place. Verify that the Manual Release the parking brake only when the vehicle is Park Release lever is locked in the released position. securely connected to a tow vehicle.
584 WHAT TO DO IN EMERGENCIES To reset the Manual Park Release: TOWING A DISABLED VEHICLE 1. Pull the tether upwards to unlock the lever. This section describes procedures for towing a disabled vehicle using a commercial wrecker service. 2. Rotate the Manual Park Release lever forward and down to its original position. 3. Re-install the access cover and the rubber storage bin liner.
WHAT TO DO IN EMERGENCIES 585 If you must use the accessories (wipers, defrosters, etc.) If flatbed equipment is not available, this vehicle must be while being towed, the ignition must be in the ON/RUN towed with the front wheels OFF the ground (using a position, not the ACC position. towing dolly, or wheel lift equipment with the front wheels raised).
586 WHAT TO DO IN EMERGENCIES CAUTION! CAUTION! (Continued) Towing this vehicle in violation of the above requirements can cause severe transmission damage. Damage from improper towing is not covered under the New Vehicle Limited Warranty. All-Wheel Drive (AWD) Models The manufacturer requires towing with all four wheels OFF the ground. Acceptable methods are to tow the vehicle on a flatbed, or with one end of vehicle raised and the opposite end on a towing dolly.
MAINTAINING YOUR VEHICLE CONTENTS 䡵 ENGINE COMPARTMENT — 2.4L . . . . . . . . . .589 ▫ Engine Oil Filter . . . . . . . . . . . . . . . . . . . . . .598 䡵 ENGINE COMPARTMENT — 3.6L . . . . . . . . . .590 ▫ Engine Air Cleaner Filter . . . . . . . . . . . . . . . .598 䡵 ONBOARD DIAGNOSTIC SYSTEM — OBD II . . .591 ▫ Maintenance-Free Battery . . . . . . . . . . . . . . .599 ▫ Loose Fuel Filler Cap Message . . . . . . . . . . . .591 ▫ Air Conditioner Maintenance . . . . . . . . . . . . .
588 MAINTAINING YOUR VEHICLE ▫ Automatic Transmission . . . . . . . . . . . . . . . .617 ▫ Front Side Marker Lamps . . . . . . . . . . . . . . .644 ▫ Appearance Care And Protection From Corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . .619 ▫ Front Fog Lamp . . . . . . . . . . . . . . . . . . . . . .645 䡵 FUSES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .625 ▫ Power Distribution Center (Fuses) . . . . . . . . . .626 ▫ Interior Fuses . . . . . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 589 ENGINE COMPARTMENT — 2.
590 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT — 3.
MAINTAINING YOUR VEHICLE 591 ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
592 MAINTAINING YOUR VEHICLE further information. Tighten the fuel filler cap until a “clicking” sound is heard. This is an indication that the fuel filler cap is properly tightened. Refer to “Onboard Diagnostic System” in “Maintaining Your Vehicle” for further information. Normally, the OBD II system will be ready. The OBD II system may not be ready if your vehicle was recently serviced, recently had a dead battery or a battery replacement.
MAINTAINING YOUR VEHICLE 593 3. Approximately 15 seconds later, one of two things will Regardless of whether your vehicle’s OBD II system is happen: ready or not, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced • The MIL will flash for about 10 seconds and then before going to the I/M station. The I/M station can fail return to being fully illuminated until you turn OFF your vehicle because the MIL is on with the engine the ignition or start the engine.
594 MAINTAINING YOUR VEHICLE available which include detailed service information for MAINTENANCE PROCEDURES your vehicle. Refer to these Service Manuals before The pages that follow contain the required maintenance attempting any procedure yourself. services determined by the engineers who designed your NOTE: Intentional tampering with emissions control vehicle.
MAINTAINING YOUR VEHICLE 595 CAUTION! (Continued) • Your vehicle has been built with improved fluids that protect the performance and durability of your vehicle and also allow extended maintenance intervals. Do not use chemical flushes in these components as the chemicals can damage your engine, transmission or air conditioning. Such damage is not covered by the New Vehicle Limited Warranty. If a flush is needed because of component malfunction, use only the specified fluid for the flushing procedure.
596 MAINTAINING YOUR VEHICLE Change Engine Oil American Petroleum Institute (API) Engine Oil The oil change indicator system will remind you that it is Identification Symbol time to take your vehicle in for scheduled maintenance. This symbol means that the oil has Refer to the “Maintenance Schedule” for further informabeen certified by the American tion. Petroleum Institute (API).
MAINTAINING YOUR VEHICLE 597 The engine oil filler cap also shows the recommended engine oil viscosity for your engine. For information on MOPAR® SAE 0W-20 engine oil or equivalent Pennzoil® engine oil filler cap location, refer to the “Engine Comor Shell Helix® is recommended for all operating tempartment” illustration in this section. peratures. This engine oil improves low temperature starting and vehicle fuel economy.
598 MAINTAINING YOUR VEHICLE engine oil. Engine oil is an engineered product and its Engine Oil Filter Selection performance may be impaired by supplemental additives. This manufacturer’s engines have a full-flow type disposable oil filter. Use a filter of this type for replacement. The Disposing Of Used Engine Oil And Oil Filters quality of replacement filters varies considerably.
MAINTAINING YOUR VEHICLE 599 WARNING! The air induction system (air cleaner, hoses, etc.) can provide a measure of protection in the case of engine backfire. Do not remove the air induction system (air cleaner, hoses, etc.) unless such removal is necessary for repair or maintenance. Make sure that no one is near the engine compartment before starting the vehicle with the air induction system (air cleaner, hoses, etc.) removed. Failure to do so can result in serious personal injury.
600 MAINTAINING YOUR VEHICLE WARNING! (Continued) CAUTION! • Battery gas is flammable and explosive. Keep flame or sparks away from the battery. Do not use a booster battery or any other booster source with an output greater than 12 Volts. Do not allow cable clamps to touch each other. • Battery posts, terminals, and related accessories contain lead and lead compounds. Wash hands after handling.
MAINTAINING YOUR VEHICLE 601 Air Conditioner Maintenance WARNING! (Continued) For best possible performance, your air conditioner should be checked and serviced by an authorized dealer at the start of each warm season. This service should include cleaning of the condenser fins and a performance test. Drive belt tension should also be checked at this time. • The air conditioning system contains refrigerant under high pressure.
602 MAINTAINING YOUR VEHICLE Refrigerant Recovery And Recycling R134a — If Equipped the manufacturer recommends that air conditioning service be performed by authorized dealer or other service facilities using recovery and recycling equipment. R-134a Air Conditioning Refrigerant is a hydrofluorocarbon (HFC) that is endorsed by the Environmental NOTE: Use only manufacturer approved A/C system Protection Agency and is an ozone-saving product. How- PAG compressor oil, and refrigerants.
MAINTAINING YOUR VEHICLE 603 Console Closeout Panel Hush Panel 3. Pull down the passenger hush panel under the dash 4. Remove the filter door by pushing down the tab on the panel top of the door to release the cover then rotate the door out and lift up.
604 MAINTAINING YOUR VEHICLE Air Filter Cover Location A/C Air Filter 5. Remove the A/C air filter by pulling it straight out of 6. Install the A/C air filter with the air filter position the housing. Take note of the air filter position indicaindicators pointing in the same direction as removal. tors.
MAINTAINING YOUR VEHICLE 605 CAUTION! The A/C air filter is identified with an arrow to indicate airflow direction through the filter. Failure to properly install the filter will result in the need to replace it more often. the application of any lubricant, the parts concerned should be wiped clean to remove dust and grit; after lubricating excess oil and grease should be removed. Particular attention should also be given to hood latching components to ensure proper function.
606 MAINTAINING YOUR VEHICLE Operation of the wipers on dry glass for long periods may cause deterioration of the wiper blades. Always use washer fluid when using the wipers to remove salt or dirt from a dry windshield. windshield washer solvent (not radiator antifreeze) and operate the system for a few seconds to flush out the residual water.
MAINTAINING YOUR VEHICLE 607 Exhaust System The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. If you notice a change in the sound of the exhaust system; or if the exhaust fumes can be detected inside the vehicle; or when the underside or rear of the vehicle is damaged; have an authorized technician inspect the complete exhaust system and adjacent body areas for broken, damaged, deteriorated, or mispositioned parts.
608 MAINTAINING YOUR VEHICLE CAUTION! • The catalytic converter requires the use of unleaded fuel only. Leaded gasoline will destroy the effectiveness of the catalyst as an emissions control device and may seriously reduce engine performance and cause serious damage to the engine. • Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition.
MAINTAINING YOUR VEHICLE 609 To minimize the possibility of catalytic converter damage: • Do not shut off the engine or interrupt the ignition, when the transmission is in gear and the vehicle is in motion. • Do not try to start the engine by pushing or towing the vehicle. WARNING! (Continued) you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool. Never try to open a cooling system pressure cap when the radiator or coolant bottle is hot.
610 MAINTAINING YOUR VEHICLE Check the engine cooling system hoses for brittle rubber, Cooling System — Drain, Flush And Refill cracking, tears, cuts, and tightness of the connection at NOTE: Some vehicles require special tools to add coolant the coolant recovery bottle and radiator. Inspect the properly. Failure to fill these systems properly could lead entire system for leaks. to severe internal engine damage.
MAINTAINING YOUR VEHICLE 611 CAUTION! CAUTION! (Continued) • Mixing of engine coolant (antifreeze) other than specified Organic Additive Technology (OAT) engine coolant (antifreeze), may result in engine damage and may decrease corrosion protection. Organic Additive Technology (OAT) engine coolant is different and should not be mixed with Hybrid Organic Additive Technology (HOAT) engine coolant (antifreeze) or any “globally compatible” coolant (antifreeze).
612 MAINTAINING YOUR VEHICLE you use the same engine coolant (OAT coolant conforming to MS-12106) throughout the life of your vehicle. (antifreeze) solution. The use of lower quality water will reduce the amount of corrosion protection in the engine cooling system.
MAINTAINING YOUR VEHICLE 613 Cooling System Pressure Cap WARNING! (Continued) The cap must be fully tightened to prevent loss of engine coolant (antifreeze), and to ensure that engine coolant (antifreeze) will return to the radiator from the coolant recovery tank. • Do not use a pressure cap other than the one specified for your vehicle. Personal injury or engine damage may result.
614 MAINTAINING YOUR VEHICLE Coolant Level The coolant bottle provides a quick visual method for determining that the coolant level is adequate. With the engine OFF and cold, the level of the engine coolant (antifreeze) in the bottle should be between the ranges indicated on the bottle. Points To Remember NOTE: When the vehicle is stopped after a few miles/ kilometers of operation, you may observe vapor coming from the front of the engine compartment.
MAINTAINING YOUR VEHICLE 615 • If frequent engine coolant (antifreeze) additions are Brake System required, the cooling system should be pressure tested In order to assure brake system performance, all brake for leaks. system components should be inspected periodically. • Maintain engine coolant (antifreeze) concentration at a Refer to the “Maintenance Schedule” for the proper minimum of 50% OAT coolant (conforming to MS-12106) maintenance intervals.
616 MAINTAINING YOUR VEHICLE Be sure to clean the top of the master cylinder area before removing the cap. If necessary, add fluid to bring the fluid level up to the requirements described on the brake fluid reservoir. With disc brakes, fluid level can be expected to fall as the brake pads wear. Brake fluid level should be checked when pads are replaced. However, low fluid level may be caused by a leak and a checkup may be needed. Use only manufacturer’s recommended brake fluid.
MAINTAINING YOUR VEHICLE 617 WARNING! (Continued) WARNING! (Continued) • To avoid contamination from foreign matter or moisture, use only new brake fluid or fluid that has been in a tightly closed container. Keep the master cylinder reservoir cap secured at all times. Brake fluid in a open container absorbs moisture from the air resulting in a lower boiling point. This may cause it to boil unexpectedly during hard or prolonged braking, resulting in sudden brake failure. This could result in a collision.
618 MAINTAINING YOUR VEHICLE NOTE: No chemical flushes should be used in any transmission; only the approved lubricant should be used. CAUTION! Using a transmission fluid other than the manufacturer’s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder. Refer to “Fluids, Lubricants, and Genuine Parts” in this section for fluid specifications. Special Additives The manufacturer strongly recommends against using any special additives in the transmission.
MAINTAINING YOUR VEHICLE 619 CAUTION! If a transmission fluid leak occurs, visit your authorized dealer immediately. Severe transmission damage may occur. Your authorized dealer has the proper tools to adjust the fluid level accurately. Appearance Care And Protection From Corrosion Protection Of Body And Paint From Corrosion Vehicle body care requirements vary according to geographic locations and usage.
620 MAINTAINING YOUR VEHICLE • If insects, tar, or other similar deposits have accumulated on your vehicle, use MOPAR® Super Kleen Bug Corrosion is the result of deterioration or removal of and Tar Remover to remove. paint and protective coatings from your vehicle. • Use a high quality cleaner wax, such as MOPAR® The most common causes are: Cleaner Wax to remove road film, stains and to protect • Road salt, dirt and moisture accumulation. your paint finish. Take care never to scratch the paint.
MAINTAINING YOUR VEHICLE 621 • If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials are well • If you drive on salted or dusty roads or if you drive packaged and sealed. near the ocean, hose off the undercarriage at least once a month. • If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel.
622 MAINTAINING YOUR VEHICLE NOTE: If your vehicle is equipped with Dark Vapor Chrome wheels DO NOT USE wheel cleaners, abrasives or polishing compounds. They will permanently damage this finish and such damage is not covered by the New Vehicle Limited Warranty. USE ONLY MILD SOAP AND WATER WITH A SOFT CLOTH. Used on a regular basis this is all that is required to maintain this finish. CAUTION! Do not use scouring pads, steel wool, a bristle brush, or metal polishes. Do not use oven cleaner.
MAINTAINING YOUR VEHICLE 623 Interior Care Instrument Panel Cover The instrument panel cover has a low glare surface, which minimizes reflections in the windshield. Do not use protectants or other products, which may cause undesirable reflections. Use soap and warm water to restore the low glare surface. Cleaning Interior Trim Clean interior trim with a damp cloth and MOPAR® Total Clean or equivalent, and if necessary, follow with MOPAR® Spot & Stain Remover or equivalent.
624 MAINTAINING YOUR VEHICLE cleaner. Use caution when cleaning the inside rear window equipped with electric defrosters or the right rear Your vehicle is equipped with plastic headlights and fog quarter window equipped with the radio antenna. Do lights that are lighter and less susceptible to stone breaknot use scrapers or other sharp instrument that may age than glass headlights. scratch the elements.
MAINTAINING YOUR VEHICLE 625 Seat Belt Maintenance WARNING! (Continued) Do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage can also weaken the fabric. assemblies must be replaced after a collision if they have been damaged (i.e., bent retractor, torn webbing, etc.). If the belts need cleaning, use a mild soap solution or lukewarm water. Do not remove the belts from the car to FUSES wash them. Dry with a soft cloth.
626 MAINTAINING YOUR VEHICLE WARNING! (Continued) • Before replacing a fuse, make sure that the ignition is off and that all the other services are switched off and/or disengaged. • If the replaced fuse blows again, contact an authorized dealer. • If a general protection fuse for safety systems (air bag system, braking system), power unit systems (engine system, gearbox system) or steering system blows, contact an authorized dealer.
MAINTAINING YOUR VEHICLE 627 Cavity F06 F07 F08 F09 F10 F11 F12 F13 Blade Fuse – – 25 Amp Clear – 20 Amp Yellow – 20 Amp Yellow 10 Amp Red Cartridge Fuse – – – – – – – – F14 10 Amp Red – F15 F16 F17 – 20 Amp Yellow – – – – Description Not Used Not Used Engine Control Module (ECM) / Fuel Inj.
628 MAINTAINING YOUR VEHICLE Cavity F18 F19 F20 F21 F22 F23 F23 Blade Fuse – – 10 Amp Red – 5 Amp Tan 70 Amp Tan 50 Amp Red Cartridge Fuse – 40 Amp Green – – – – – F24 F25B – 20 Amp Yellow – – F26 F27 F28 F29 – – 15 Amp Blue – – – – – Description Not Used Starter Solenoid A/C Compressor Clutch Not Used Radiator Fan Enable Body Controller Module (BCM) – Feed 2 Voltage Stability Module (VSM) #2 – If Equipped With Stop/Start Engine Option Not Used Front Washer Pump – If Equipped with Stop/ Start Opti
MAINTAINING YOUR VEHICLE 629 Cavity F30 F31 F32 F33 F34 F35 F36 F37 F38 F39 F40 F41 Blade Fuse 10 Amp Red – – – – – – – – – – – Cartridge Fuse – – – – – – – 50 Amp Red – 40 Amp Green – 50 Amp Red F41 F42 — – 60 Amp Yellow – Description Engine Control Module (ECM) / EPS Not Used Not Used Not Used Not Used Not Used Not Used Radiator Fan PWM Controller Not Used HVAC Blower Motor Not Used Voltage Stability Module (VSM) #1 – If Equipped With Stop/Start Engine Option Body Controller Module (BCM) – Feed 1 N
630 MAINTAINING YOUR VEHICLE Cavity F43 F44 F45 F46 F47 F48 F49 F50 F51 F52 F53 F54 F55 Blade Fuse 20 Amp Yellow – – – – – – – – – – – 10 Amp Red Cartridge Fuse – – 30 Amp Pink 25 Amp Clear – 30 Amp Pink 30 Amp Pink 30 Amp Pink – – 30 Amp Pink 30 Amp Pink – F56 15 Amp Blue – Description Fuel Pump Motor Not Used Passenger Door Module (PDM) – If Equipped Sunroof – If Equipped Not Used Driver Door Module (DDM) Power Inverter (115V A/C) – If Equipped Windshield Wiper Smart Motor (WWSM) Not Used Not Used
MAINTAINING YOUR VEHICLE 631 Cavity F57 F58 Blade Fuse – 10 Amp Red Cartridge Fuse – – F59 F60 F61 F62 F63 F64 F65 – 20 Amp Yellow – – 20 Amp Yellow 20 Amp Yellow 10 Amp Red 30 Amp Pink – – – – – – F66 15 Amp Blue – Description Not Used Occupant Classification Module/Voltage Stability Module (VSM) #2 – If Equipped With Stop/Start Engine Option Drivetrain Control Module (DTCM) Power Outlet – Center Console Not Used Not Used Front Heated Seats – If Equipped Heated Steering Wheel – If Equipped In Car
632 MAINTAINING YOUR VEHICLE Cavity F67 Blade Fuse 10 Amp Red Cartridge Fuse – F68 F69 – 10 Amp Red – – F70 5 Amp Tan – F71 20 Amp Yellow – F72 F73 F74 F75 F76 10 Amp Red – – 20 Amp Yellow 10 Amp Red – – 30 Amp Pink – – Description In Car Temperature Sensor/Humidity Sensor/ Drivers Assist System Module (DASM)/Park Assist (PAM) – If Equipped Not Used Gear Shift Module (GSM)/Active Grill Shutter (AGS).
MAINTAINING YOUR VEHICLE 633 Cavity F77 F78 Blade Fuse 10 Amp Red 10 Amp Red Cartridge Fuse – – F79 10 Amp Red – F80 F81 F82 F83 F84 F85 F86 20 Amp Yellow – – – – – 20 Amp Yellow – – – 20 Amp Blue 30 Amp Pink – – F87A 20 Amp Yellow – Description UCI Port/Brake Pedal Switch Diagnostic Port/Steering Column Control Module (SCCM) Integrated Center Stack (ICS)/Switch Bank/ Instrument Panel Cluster (IPC)/EPB SW Radio Not Used Not Used Engine Control Module (ECM) Electric Park Brake (EPB) – Left Not U
634 MAINTAINING YOUR VEHICLE Cavity F88 Blade Fuse 10 Amp Red Cartridge Fuse – F89 F90 F91 F92 F93 – – – – – – – – – 40 Amp Green F94 F95 – 10 Amp Red 30 Amp Pink – F96 F97 10 Amp Red 10 Amp Red – – Description Collision Mitigation Module (CMM)/ Electrochromatic Mirror/Haptic Lane Feedback Module (Half)/Humidity Sensor– If Equipped Not Used Not Used Not Used Not Used Brake System Module (BSM) – Pump Motor – If Equipped Electric Park Brake (EPB) – Right Electrochromatic Mirror/Rain/Pass.
MAINTAINING YOUR VEHICLE 635 Cavity F98 F99 F100 Blade Fuse 25 Amp Clear – – Cartridge Fuse – – – Description Audio Amplifier – If Equipped Not Used Not Used Interior Fuses The interior fuse panel is located in the passenger compartment on the left side dash panel under the instrument panel. Cavity F13 F32 F36 F37 F38 F43 Blade Fuse 15 Amp Blue 10 Amp Red 10 Amp Red 7.5 Amp Brown 20 Amp Yellow 20 Amp Yellow Description Low Beam Left Interior Lighting Intrusion Module / Siren Aux.
636 MAINTAINING YOUR VEHICLE Cavity F48 F49 F51 Blade Fuse 20 Amp Yellow 7.5 Amp Brown 10 Amp Red F53 F89 F91 F92 F93 7.5 Amp Brown 5 Amp Tan 5 Amp Tan 5 Amp Tan 10 Amp Red Description Horns Lumbar Support Driver Window Switch / Power Mirrors – If Equipped UCI Port (USB & AUX) Trunk Lamp Fog Lamp Front Left Fog Lamp Front Right Low Beam Right • Anytime you store your vehicle, or keep it out of service (i.e.
MAINTAINING YOUR VEHICLE 637 REPLACEMENT BULBS Interior Bulbs Front Courtesy/Reading Lamp Center Courtesy/Reading Lamp Visor Vanity Lamp Glove Box Lamp Shift Indicator Lamp Rear Compartment (Trunk) Lamp NOTE: For lighted switches, see your authorized dealer for replacement.
638 MAINTAINING YOUR VEHICLE Exterior Bulbs High Intensity Discharge Headlamp Bi-Halogen Headlamp Daytime Running Lamp Front Turn Signal Lamp Side Marker Lamp Front Park Lamp Front Fog Lamp LED Front Fog Lamp Center High Mounted Stop (CHMSL) Lamp Stop/Turn Signal Lamp Rear Tail/Side Marker Lamp Backup Lamp License Lamp Bulb Number HID (Serviced at Authorized Dealer) HIR2 LED (Serviced at Authorized Dealer) PWY24W SV W3W LED (Serviced at Authorized Dealer) H11 LED (Serviced at Authorized Dealer) LED (Servi
MAINTAINING YOUR VEHICLE 639 NOTE: On vehicles equipped with HID headlamps, when the headlamps are turned on, there is a blue hue to NOTE: Lens fogging can occur under certain atmothe lights. This diminishes and becomes more white after spheric conditions. This will usually clear as atmospheric approximately 10 seconds, as the system charges. conditions change to allow the condensation to change back into a vapor. Turning the lamps on will usually WARNING! accelerate the clearing process.
640 MAINTAINING YOUR VEHICLE Access Door Headlamp Bulb Cap 2. Reach behind the headlamp housing to access the 4. Firmly grasp the headlamp bulb socket assembly and headlamp bulb cap. rotate counterclockwise to remove from the housing. 3. Firmly grasp the headlamp bulb cap and rotate it counterclockwise to unlock it.
MAINTAINING YOUR VEHICLE 641 Headlamp Bulb Socket Headlamp Bulb 5. Disconnect the bulb from the electrical connector and then connect the replacement bulb. CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol.
642 MAINTAINING YOUR VEHICLE 6. Install the bulb and connector assembly into the headlamp housing and rotate clockwise to lock it in place. 7. Install the headlamp bulb cap in the headlamp housing and rotate clockwise to lock it in place. 8. Lock headlamp access door in wheel liner. Front Turn Signal Lamp 1. Open the hood. NOTE: Removal of the air cleaner filter housing may be necessary prior to replacing bulbs in the lamp assembly on the passenger side of the vehicle. Beauty Cover 3.
MAINTAINING YOUR VEHICLE 643 7. Install air cleaner filter housing, if removed. 8. Install brace, brace bolts and tighten as shown. Front Turn Signal Lamp Socket 5. Pull the bulb out of the socket and insert the replacement bulb. 7 Brace Bolt Tightening Sequence 6. Install the front turn signal lamp socket assembly into 9. Install beauty cover. the housing, and rotate the front turn signal lamp socket clockwise to lock it in place.
644 MAINTAINING YOUR VEHICLE Front Side Marker Lamps 1. Remove the three fasteners from the inner wheel liner and carefully peel back liner for access. Front Side Marker Lamp Bulb Removal 3. Remove bulb from the front side marker lamp socket and replace with a new bulb. 4. Install front side marker lamp socket in lamp assembly and rotate 1/4 turn clockwise to lock into place. 2. Firmly grasp the front side marker lamp socket and rotate 1/4 turn counterclockwise to remove it from the 5.
MAINTAINING YOUR VEHICLE 645 3. Rotate the front fog lamp socket counterclockwise, and remove the bulb and socket assembly from the 1. Remove the three fasteners from the lower closeout, front fog lamp housing. and peel down the lower closeout. Front Fog Lamp 7 Lower Closeout 2. Reach behind the fog lamp housing to access the bulb. Front Fog Lamp Socket 4. Pull the bulb out of the socket and insert the replacement bulb.
646 MAINTAINING YOUR VEHICLE CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol. Backup Lamps (Passenger Side) 1. Open trunk lid. 2. Remove the passenger side access cover. 3. Remove the inner trunk lid handle cover. 4. Remove the two screws and remove the inner trunk 5. Install the front fog lamp socket assembly into the into lid handle.
MAINTAINING YOUR VEHICLE 647 Inner Deck Panel Backup Lamp Socket 6. Rotate the backup lamp socket counter clockwise 1/4 7. Remove the bulb from the socket and install the turn to remove the backup lamp socket from the trunk replacement bulb. lid lamp housing. 8. Install the backup lamp socket into the trunk lid lamp housing.
648 MAINTAINING YOUR VEHICLE 9. Rotate backup lamp socket clockwise 1/4 turn to lock it into place. 10. Reposition the inner deck panel and secure with a push pin if removed. 11. Install access cover. Backup Lamps (Driver Side) 1. Open trunk lid. 2. Remove the drivers side access cover. 3. Remove inner deck lid support push pin. Backup Lamp Socket NOTE: If necessary remove any additional inner deck lid 5. Rotate the backup lamp socket counter clockwise 1/4 trim push pins to gain access.
MAINTAINING YOUR VEHICLE 649 7. Install the backup lamp socket into the trunk lid lamp housing. 8. Rotate backup lamp socket clockwise 1/4 turn to lock it into place. 9. Reposition the inner deck panel and secure with a push pin if removed. 10. Install the access cover. Stop/Rear Turn Signal Lamp 1. Open the trunk lid. Tail Lamp Beauty Cover 2. Remove the tail lamp housing beauty cover by grasping the top edge and pulling rearward to expose the 3. Remove the tail lamp housing bolts tail lamp housing bolts.
650 MAINTAINING YOUR VEHICLE 5. Rotate the stop/rear turn signal lamp socket 1/4 turn counterclockwise and remove it from the tail lamp housing. 6. Remove the bulb from the socket and install the replacement bulb. 7. Install the bulb socket into the tail lamp housing and rotate the bulb socket ¼ turn clockwise to lock it in place. 8. Install the tail lamp housing. 9. Install the tail lamp housing beauty cover. Tail Lamp Bolts License Plate Lamp 4. Pull the tail lamp housing directly rearward to dis- 1.
MAINTAINING YOUR VEHICLE 651 FLUID CAPACITIES U.S. Fuel (Approximate) 2.4L and 3.6L Engines 15.8 Gallons Engine Oil With Filter 2.4 Liter Engine (SAE 0W-20, API Certified) 5.5 Quarts 3.6 Liter Engine (SAE 5W-20, API Certified) 6 Quarts Cooling System* 2.4 Liter Engine (MOPAR® Antifreeze/ 7.2 Quarts Engine Coolant 10 Year/150,000 Mile Formula) 3.6 Liter Engine (MOPAR® Antifreeze/ 8.7 Quarts Engine Coolant 10 Year/150,000 Mile Formula) * Includes heater and coolant reservoir filled to MAX level.
652 MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant Engine Oil – 2.4L Engine Fluid, Lubricant, or Genuine Part We recommend you use MOPAR® Antifreeze/Coolant 10 Year/150,000 Mile Formula OAT (Organic Additive Technology) or equivalent meeting the requirements of Chrysler Material Standard MS-12106.
MAINTAINING YOUR VEHICLE 653 Component Engine Oil – 3.6L Engine Engine Oil Filter Spark Plugs – 2.4L Engine Spark Plugs – 3.6L Engine Fuel Selection – 2.4L Engine Fuel Selection – 3.6L Engine Fluid, Lubricant, or Genuine Part We recommend you use API Certified SAE 5W-20 Engine Oil, meeting the requirements of Chrysler Material Standard MS-6395 such as MOPAR®, Pennzoil®, and Shell Helix®. Refer to your engine oil filler cap for correct SAE grade. We recommend you use a MOPAR® Engine Oil Filter.
654 MAINTAINING YOUR VEHICLE CAUTION! CAUTION! (Continued) • Mixing of engine coolant (antifreeze) other than specified Organic Additive Technology (OAT) engine coolant (antifreeze), may result in engine damage and may decrease corrosion protection. Organic Additive Technology (OAT) engine coolant is different and should not be mixed with Hybrid Organic Additive Technology (HOAT) engine coolant (antifreeze) or any “globally compatible” coolant (antifreeze).
MAINTAINING YOUR VEHICLE 655 Chassis Component Automatic Transmission Brake Master Cylinder Fluid, Lubricant, or Genuine Part Use only MOPAR® ZF 8&9 Speed ATF™ Automatic Transmission Fluid, or equivalent. Failure to use the correct fluid may affect the function or performance of your transmission. We recommend you use MOPAR® DOT 3 Brake Fluid, SAE J1703 should be used. If DOT 3, SAE J1703 brake fluid is not available, then DOT 4 is acceptable. Use only recommended brake fluids.
M A I N T E N A ▫ Maintenance Chart . . . . . . . . . . . . . . . . . . . .660 N C E MAINTENANCE SCHEDULES CONTENTS 䡵 MAINTENANCE SCHEDULE . . . . . . . . . . . . .
M A I N T E N A N C E S C H E D U L E S 8 658 MAINTENANCE SCHEDULES MAINTENANCE SCHEDULE Your vehicle is equipped with an automatic oil change indicator system. The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Based on engine operation conditions, the oil change indicator message will illuminate. This means that service is required for your vehicle.
MAINTENANCE SCHEDULES 659 M Once A Month Or Before A Long Trip: • Check engine oil level. • Check windshield washer fluid level. • Check tire pressure and look for unusual wear or damage. Rotate tires at the first sign of irregular wear, even if it occurs before the oil indicator system turns on. • Check the fluid levels of the coolant reservoir and brake master cylinder, fill as needed. • Check function of all interior and exterior lights. Required Maintenance Intervals.
20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 110,000 120,000 130,000 140,000 150,000 2 3 4 5 6 7 8 9 10 11 12 13 14 15 32,000 48,000 64,000 80,000 96,000 112,000 128,000 144,000 160,000 176,000 192,000 208,000 224,000 240,000 M 660 MAINTENANCE SCHEDULES A I Maintenance Chart N T E N Mileage: A N C Or Years: E Or Kilometers: S C H Additional Inspections E D Inspect the CV joints.
Mileage: 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 110,000 120,000 130,000 140,000 150,000 Or Years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Or Kilometers: 32,000 48,000 64,000 80,000 96,000 112,000 128,000 144,000 160,000 176,000 192,000 208,000 224,000 240,000 MAINTENANCE SCHEDULES 661 M Replace spark plugs – 3.6L Engine ** Flush and replace the engine coolant at 10 years or 150,000 miles (240,000 km) whichever comes first.
M 662 MAINTENANCE SCHEDULES A I WARNING! N T E • You can be badly injured working on or around a motor vehicle. Do only service work for which you N A have the knowledge and the right equipment. If N you have any doubt about your ability to perform a C service job, take your vehicle to a competent meE S C H E D U L E S 8 chanic. • Failure to properly inspect and maintain your vehicle could result in a component malfunction and effect vehicle handling and performance. This could cause an accident.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS 䡵 SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . .665 ▫ Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY). . . . . . . . . . . . . . . . . . .667 ▫ Prepare For The Appointment. . . . . . . . . . . . .665 ▫ Service Contract . . . . . . . . . . . . . . . . . . . . . .667 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . . .665 䡵 WARRANTY INFORMATION . . . . . . . . . . . . .
664 IF YOU NEED CONSUMER ASSISTANCE 䡵 DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES . . . . . . . . . . . . . . . . .671 ▫ Treadwear. . . . . . . . . . . . . . . . . . . . . . . . . . .671 ▫ Traction Grades . . . . . . . . . . . . . . . . . . . . . . .671 ▫ Temperature Grades. . . . . . . . . . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE 665 SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment Be Reasonable With Requests If you list a number of items and you must have your vehicle by the end of the day, discuss the situation with the service advisor and list the items in order of priority. At many authorized dealers, you may obtain a rental vehicle at a minimal daily charge. If you need a rental, it is advisable to make these arrangements when you call for an appointment.
666 IF YOU NEED CONSUMER ASSISTANCE facilities, factory-trained technicians, special tools, and • Authorized dealer name the latest information to ensure the vehicle is fixed • Vehicle Identification Number (VIN) correctly and in a timely manner. • Vehicle delivery date and mileage This is why you should always talk to an authorized dealer service manager first. Most matters can be re- Chrysler Group LLC Customer Center solved with this process. P.O.
IF YOU NEED CONSUMER ASSISTANCE 667 Mexico, D. F. Canadian residents with hearing difficulties that require assistance can use the special needs relay service offered by Bell Canada. For TTY teletypewriter users, dial 711 and for Voice callers, dial 1-800-855-0511 to connect with a Bell Relay Service operator.
668 IF YOU NEED CONSUMER ASSISTANCE The manufacturer will not stand behind any service contract that is not the manufacturer’s service contract. It is not responsible for any service contract other than the manufacturer’s service contract. If you purchased a service contract that is not a manufacturer’s service contract, and you require service after the manufacturer’s New Vehicle Limited Warranty expires, please refer to the contract documents, and contact the person listed in those documents.
IF YOU NEED CONSUMER ASSISTANCE 669 To contact NHTSA, you may either call the Auto Safety Hotline toll free at 1–888–327–4236 (TTY: 1–800– MOPAR® fluids, lubricants, parts, and accessories are 424–9153), or go to http://www.safercar.gov; or write available from an authorized dealer. They are recomto: Administrator, NHTSA, 1200 New Jersey Avenue, mended for your vehicle in order to help keep the vehicle SE., West Building, Washington, D.C. 20590. You can operating at its best.
670 IF YOU NEED CONSUMER ASSISTANCE PUBLICATION ORDER FORMS To order the following manuals, you may use either the website or the phone numbers listed below. Visa, Mastercard, American Express, and Discover orders are accepted. If you prefer mailing your payment, please call for an order form. Diagnostic Procedure Manuals Diagnostic Procedure Manuals are filled with diagrams, charts and detailed illustrations.
IF YOU NEED CONSUMER ASSISTANCE 671 Call toll free at: Treadwear • 1–800–890–4038 (U.S.) The Treadwear grade is a comparative rating, based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half times as well on the government course as a tire graded 100.
672 IF YOU NEED CONSUMER ASSISTANCE WARNING! The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics. Temperature Grades The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel.
INDEX 10
674 INDEX About Your Brakes . . . . . . . . . . . . . . . . . . . . . . . .481 ABS (Anti-Lock Brake System) . . . . . . . . . . . . . . . .482 Adaptive Cruise Control (ACC) (Cruise Control) . . .182 Adding Engine Coolant (Antifreeze) . . . . . . . . . . . .611 Additives, Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . .533 Air bag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60 Air Bag Advance Front Air Bag . . . . . . . . . . . . . . . . . . . .61 Air Bag Components . . . . .
INDEX 675 Alarm Arm The System . . . . . . . . . . . . . . . . . . . . . . . .19 Disarm The System . . . . . . . . . . . . . . . . . . . . . . .19 Rearming The System . . . . . . . . . . . . . . . . . . . . .18 Tamper Alert . . . . . . . . . . . . . . . . . . . . . . . . . . .20 Vehicle Security Alarm . . . . . . . . . . . . . . . . . . . .18 Alarm, Panic . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 Alarm (Security Alarm) . . . . . . . . . . . . . . . . . . . . .331 All Wheel Drive (AWD). .
676 INDEX Caps, Filler Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .539 Oil (Engine) . . . . . . . . . . . . . . . . . . . . . . . . . . .589 Radiator (Coolant Pressure) . . . . . . . . . . . . . . . .613 Carbon Monoxide Warning . . . . . . . . . . . . . . . . . .110 Cargo Area Features . . . . . . . . . . . . . . . . . . . . . . .310 Cargo Compartment . . . . . . . . . . . . . . . . . . . . . . .310 Car Washes . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 677 Center Seat LATCH . . . . . . . . . . . . . . . . . . . . . .100 Child Restraints . . . . . . . . . . . . . . . . . . . . . . . . .86 Child Seat Installation . . . . . . . . . . . . . . . . . . . .103 How To Stow An Unused ALR Seat Belt . . . . . . .101 Infants And Child Restraints . . . . . . . . . . . . . . . .89 Install A LATCH-compatible Child Restraint . . . .100 Installing Child Restraints Using The Vehicle Seat Belt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
678 INDEX Cruise Control (Speed Control). . . . . . . . . . . . . . . .182 Door Locks Child-Protection Door Lock — Rear Doors . . . . . .34 Cupholders . . . . . . . . . . . . . . . . . . . . . . . . . . . . .303 Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 Customer Assistance . . . . . . . . . . . . . . . . . . . . . . .665 Key Fob . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 Key Fob Emergency Key . . . . . . . . . . . . . . . . . . .25 Data Recorder, Event . . .
INDEX 679 Driving Through Flowing, Rising, or Shallow Standing Water . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .472 E-85 Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . Electrical Power Outlets. . . . . . . . . . . . . . . . . Electric Parking Brake . . . . . . . . . . . . . . . . . . Electric Rear Window Defrost. . . . . . . . . . . . . Electric Remote Mirrors . . . . . . . . . . . . . . . . . Electronic Brake Control System . . . . . . . . . . .
680 INDEX Fails to Start . . . . . . . . . . . . . . . . . . . . . . . . . . .450 Flooded, Starting . . . . . . . . . . . . . . . . . . . . . . .450 Fuel Requirements . . . . . . . . . . . . . . . . . . . . . .531 Jump Starting . . . . . . . . . . . . . . . . . . . . . . . . . .576 Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .595 Oil Filler Cap . . . . . . . . . . . . . . . . . . . . . . . . . .589 Oil Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 681 Replacement Parts . . . . . . . . . . . . Starting . . . . . . . . . . . . . . . . . . . Flooded Engine Starting . . . . . . . . . Floor Console . . . . . . . . . . . . . . . . . Fluid, Brake . . . . . . . . . . . . . . . . . . Fluid Capacities . . . . . . . . . . . . . . . Fluid Leaks . . . . . . . . . . . . . . . . . . Fluid Level Checks Brake . . . . . . . . . . . . . . . . . . . . . Engine Oil . . . . . . . . . . . . . . . . . Fluids, Lubricants and Genuine Parts Fog Lights . . . . . . . . .
682 INDEX Gauges Coolant Temperature Fuel . . . . . . . . . . . . Speedometer . . . . . Tachometer . . . . . . . Gear Ranges . . . . . . . . General Information . . Glass Cleaning . . . . . . GVWR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 683 Illuminated Entry . . . . . . . . . . . . . . . . . . . . . . . . . .21 Courtesy Lights . . . . . . . . . . . . . . . . . . . . . . . . .21 Front Courtesy Overhead Console . . . . . . . . . . . .21 Illuminated Entry . . . . . . . . . . . . . . . . . . . . . . . .21 Remote Keyless Entry (RKE) Transmitter . . . . . . .21 Inside Rearview Mirror . . . . . . . . . . . . . . . . . . . . .122 Instrument Cluster . . . . . . . . . . . . . . . . . . . . . . . .321 Instrument Cluster . . . . . . . . . . . .
684 INDEX .24 Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .113 Airbag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82 .36 Anti-Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . .328 .36 Automatic Headlights . . . . . . . . . . . . . . . . . . . .160 .36 Battery Saver . . . . . . . . . . . . . . . . . . . . . . . . . .170 .23 Brake Assist Warning . . . . . . . . . . . . . . . . . . . .491 .23 Brake Warning . . . . . . . . . . . . . . . . . . . . . . .
INDEX 685 High Beam . . . . . . . . . . . . . . . . . . . . . . . . . . . .166 High Beam Indicator . . . . . . . . . . . . . . . . . . . . .329 High Beam/Low Beam Select . . . . . . . . . . . . . . .166 Illuminated Entry . . . . . . . . . . . . . . . . . . . . . . . .21 Instrument Cluster . . . . . . . . . . . . . . . . . . . . . .159 Intensity Control . . . . . . . . . . . . . . . . . . . . . . . .168 Interior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .168 License . . . . . . . . . . . . .
686 INDEX Manual, Service . . . . . . . . . . . . . . . . . . . . . . . . . .670 Marker Lights, Side . . . . . . . . . . . . . . . . . . . . . . . .642 Master Cylinder (Brakes) . . . . . . . . . . . . . . . . . . . .615 Memory Feature (Memory Seat) . . . . . . . . . . . . . . .153 Memory Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . .153 Memory Seats and Radio . . . . . . . . . . . . . . . . . . . .153 Methanol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .532 Mirrors . . . . .
INDEX 687 Synthetic . . . . . . . . . . . . . . . . . . . . . . . . . . . . .597 Viscosity . . . . . . . . . . . . . . . . . . . . . . . . . . . . .597 Oil Filter, Change . . . . . . . . . . . . . . . . . . . . . . . . .598 Oil Filter, Selection . . . . . . . . . . . . . . . . . . . . . . . .598 Onboard Diagnostic System . . . . . . . . . . . . . . . . . .591 Opener, Garage Door (HomeLink®) . . . . . . . . . . . .281 Operating Precautions . . . . . . . . . . . . . . . . . . . . . .
688 INDEX Rain Sensitive Wiper System . . . . . . . . . . . . . . . . .175 Rear Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . .274 Rear Cupholder . . . . . . . . . . . . . . . . . . . . . . . . . .304 Rear ParkSense System . . . . . . . . . . . . . . . . . . . . .221 Rear Seat, Folding . . . . . . . . . . . . . . . . . . . . . . . . .152 Rear Window Defroster . . . . . . . . . . . . . . . . . . . . .314 Rear Window Features . . . . . . . . . . . . . . . . . . . . .314 Recorder, Event Data .
INDEX 689 Replacement Parts. . . . . . . . . . . . . . . . . . . . . . . . .593 Replacement Tires . . . . . . . . . . . . . . . . . . . . . . . . .515 Reporting Safety Defects . . . . . . . . . . . . . . . . . . . .669 Restraint, Head. . . . . . . . . . . . . . . . . . . . . . . . . . .149 Restraints, Child . . . . . . . . . . . . . . . . . . . . . . . . . . .86 Restraints, Occupant . . . . . . . . . . . . . . . . . . . . . . . .47 Rotation, Tires . . . . . . . . . . . . . . . . . . . . . . . . . . .
690 INDEX Front Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48 Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111 Operating Instructions . . . . . . . . . . . . . . . . . . . .53 Pretensioners . . . . . . . . . . . . . . . . . . . . . . . . . . .57 Rear Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50 Reminder . . . . . . . . . . . . . . . . . . . . . . . . . . . . .325 Untwisting Procedure . . . . . . . . . . . . . . . . . . . . .55 Seats . . . . .
INDEX 691 Specifications Fuel (Gasoline) . . . . . . . . . . . . . . . . . . . . . . . . .652 Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .652 Speed Control (Cruise Control). . . . . . . . . . . . . . . .178 Speedometer. . . . . . . . . . . . . . . . . . . . . . . . . . . . .324 Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27 Cold Weather . . . . . . . . . . . . . . . . . . . . . . . . . .449 Engine Fails to Start . . . . . . . . . . . . . . . . . . .
692 INDEX Tire Markings . . . . . . . . . . . . . . . . Tires . . . . . . . . . . . . . . . . . . . . . . Aging (Life of Tires) . . . . . . . . . Air Pressure . . . . . . . . . . . . . . . Chains . . . . . . . . . . . . . . . . . . . Changing . . . . . . . . . . . . . . . . . Compact Spare . . . . . . . . . . . . . General Information . . . . . . . . . High Speed . . . . . . . . . . . . . . . Inflation Pressures . . . . . . . . . . . Jacking . . . . . . . . . . . . . . . . . . . Life of Tires . . . . . . .
INDEX 693 Transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . .460 Automatic . . . . . . . . . . . . . . . . . . . . . . . . . . . .460 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . .617 Transmitter Battery Service (Remote Keyless Entry) . .25 Transmitter, Garage Door Opener (HomeLink®). . . .281 Transmitter Programming (Remote Keyless Entry) . . .25 Transmitter, Remote Keyless Entry (RKE) . . . . . . . . .22 Transporting Pets . . . . . . . . . . . . . . . . . . . . . . . .
694 INDEX Water Driving Through . . . . . . . . . . . . . . . . . . . . . . . .472 Wheel and Wheel Trim . . . . . . . . . . . . . . . . . . . . .621 Wheel and Wheel Trim Care . . . . . . . . . . . . . . . . .621 Wind Buffeting. . . . . . . . . . . . . . . . . . . . . . . . . . . .44 Window Fogging . . . . . . . . . . . . . . . . . . . . . . . . .421 Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 Auto Down . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained personnel. The following must be observed during installation. The positive power connection should be made directly to the battery and fused as close to the battery as possible.
2015 200 2015 OWNER’S MANUAL Chrysler Group LLC 15UF-126-AC Third Edition Rev 1 Printed in U.S.A.
