2014 300 SRT 2014 OWNER’S MANUAL Chrysler Group LLC 14C482-126-AD Fourth Edition Printed in U.S.A.
VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name Chrysler Group LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefore. Drunken driving is one of the most frequent causes of accidents. This manual illustrates and describes the operation of features and equipment that are either standard or optional on this vehicle.
SECTION TABLE OF CONTENTS PAGE 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105 3 4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION CONTENTS 䡵 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . .4 䡵 VEHICLE IDENTIFICATION NUMBER . . . . . . . .6 䡵 HOW TO USE THIS MANUAL . . . . . . . . . . . . . .4 䡵 VEHICLE MODIFICATIONS/ALTERATIONS . . . .7 䡵 WARNINGS AND CAUTIONS . . . . . . . . . . . . . .
4 INTRODUCTION When it comes to service, remember that your authorized dealer knows your vehicle best, has factory-trained techCongratulations on selecting your new Chrysler Group nicians and genuine parts, and cares about your satisfacLLC vehicle. Be assured that it represents precision tion. workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles.
INTRODUCTION 5 1
6 INTRODUCTION WARNINGS AND CAUTIONS This Owners Manual contains WARNINGS against operating procedures that could result in a collision or bodily injury. It also contains CAUTIONS against procedures that could result in damage to your vehicle. If you do not read this entire Owners Manual, you may miss important information. Observe all Warnings and Cautions. VEHICLE IDENTIFICATION NUMBER The Vehicle Identification Number (VIN) is on the left front corner of the instrument panel.
INTRODUCTION 7 VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death. VIN Location NOTE: It is illegal to remove or alter the VIN.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS 䡵 A WORD ABOUT YOUR KEYS . . . . . . . . . . . . .12 ▫ To Arm The System . . . . . . . . . . . . . . . . . . . . .19 ▫ Keyless Ignition Node (KIN) . . . . . . . . . . . . . .12 ▫ To Disarm The System . . . . . . . . . . . . . . . . . . .19 ▫ Key Fob . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 ▫ Tamper Alert . . . . . . . . . . . . . . . . . . . . . . . . .21 ▫ Ignition Or Accessory On Message . . . . . . . . . .
10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Transmitter Battery Replacement . . . . . . . . . . .24 䡵 TRUNK LOCK AND RELEASE . . . . . . . . . . . . .43 ▫ General Information . . . . . . . . . . . . . . . . . . . .26 䡵 TRUNK SAFETY WARNING. . . . . . . . . . . . . . . .44 䡵 REMOTE STARTING SYSTEM — IF EQUIPPED . .26 ▫ Trunk Emergency Release . . . . . . . . . . . . . . . .44 ▫ How To Use Remote Start . . . . . . . . . . . . . . . .27 䡵 OCCUPANT RESTRAINTS . . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 ▫ Seat Belt Extender . . . . . . . . . . . . . . . . . . . . .59 䡵 SAFETY TIPS . . . . . . . . . . . . . . . . . . . . . . . . .100 ▫ Supplemental Restraint System (SRS) — Air Bags . . . . . . . . . . . . . . . . . . . . . . . . . . . .59 ▫ Air Bag Deployment Sensors And Controls . . . .66 ▫ Event Data Recorder (EDR) . . . . . . . . . . . . . . .74 ▫ Child Restraints . . . . . . . . . . . . . . . . . . . . . . .75 䡵 ENGINE BREAK-IN RECOMMENDATIONS . . . .
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The Keyless Ignition Node (KIN) has four operating positions, three of which are labeled and will illuminate Your vehicle uses a keyless ignition system. This system when in position. The three positions are OFF, ACC, and consists of a Key Fob with Remote Keyless Entry (RKE) ON/RUN. The fourth position is START, during start transmitter and a Keyless Ignition Node (KIN). RUN will illuminate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 Key Fob The Key Fob also contains the Remote Keyless Entry (RKE) transmitter and an emergency key, which stores in the rear of the Key Fob. The emergency key allows for entry into the vehicle should the battery in the vehicle or the Key Fob go dead. The emergency key is also for locking/unlocking the glove compartment. You can keep the emergency key with you when valet parking.
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Mechanical Latch On The Back Of The Key Fob Emergency Key Removal NOTE: You can insert the double-sided emergency key into the lock cylinders with either side up.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 Ignition Or Accessory On Message Opening the driver’s door when the ignition is in ACC or ON (engine not running), a chime will sound to remind you to cycle the ignition to OFF. In addition to the chime, the ignition or accessory on message will display in the cluster.
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • Do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. CAUTION! An unlocked car is an invitation to thieves. Always remove the Key Fob from vehicle, cycle the ignition OFF and lock all doors when leaving the vehicle unattended.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 If the Vehicle Security Light turns on during normal vehicle operation (vehicle running for longer than 10 seconds), it indicates that there is a fault in the electronics. Should this occur, have the vehicle serviced as soon as possible by an authorized dealer. CAUTION! • Do not make modifications or alterations to the immobilizer system. Modifications or alterations to the immobilization system may result in a loss of security protection.
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Duplication of Key Fobs may be performed at an autho- • This device must accept any interference that may be received, including interference that may cause underized dealer. This procedure consists of programming a sired operation. blank Key Fob to the vehicle electronics. A blank Key Fob is one that has never been programmed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 Rearming Of The System If something triggers the alarm, and no action is taken to disarm it, the Vehicle Security Alarm will turn the horn off after three minutes, turn all of the visual signals off after 15 minutes, and then the Vehicle Security Alarm will rearm itself. To Arm The System Follow these steps to arm the Vehicle Security Alarm: 2.
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Grasp the Passive Entry Unlock Door Handle if • When the Vehicle Security Alarm is armed, the interior equipped, refer to “Keyless Enter-N-Go™” in “Things power door lock switches will not unlock the doors. To Know Before Starting Your Vehicle” for further The Vehicle Security Alarm is designed to protect your information.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 Tamper Alert NOTE: If something has triggered the Vehicle Security Alarm in • The front courtesy overhead console and door couryour absence, the horn will sound three times and the tesy lights will turn on if the dimmer control is in the exterior lights will blink three times when you disarm the “Dome ON” position (extreme top position). Vehicle Security Alarm. Check the vehicle for tampering.
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Driving at speeds 5 mph (8 km/h) and above To Unlock The Doors disables the system from responding to all RKE transmit- Push and release the UNLOCK button on the RKE ter buttons for all RKE transmitters. transmitter once to unlock the driver’s door or twice within five seconds to unlock all doors. The turn signal lights will flash to acknowledge the unlock signal. The illuminated entry system will also turn on.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 If the vehicle is equipped with Passive Entry, refer to “Keyless Enter-N-Go™” under “Things To Know Before This feature will cause the signal lights to flash when the Starting Your Vehicle” for further information. doors are locked with the RKE transmitter. This feature can be turned on or turned off.
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • You may need to be less than 35 ft (11 m) from the vehicle when using the RKE transmitter to turn off the To turn the Panic Alarm feature on or off, push and hold Panic Alarm due to the radio frequency noises emitted the PANIC button on the RKE transmitter for at least one by the system. second and release.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 1. Remove the emergency key by sliding the mechanical latch on the back of the RKE transmitter sideways with your thumb and then pull the key out with your other hand. of the RKE transmitter apart. Make sure not to damage the seal during removal. 2 Separating The RKE Transmitter Case 3. Remove the battery by turning the back cover over (battery facing downward) and tapping it lightly on a 2.
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE on the battery to the + sign on the inside of the battery clip, located on the back cover. Avoid touching the new battery with your fingers. Skin oils may cause battery deterioration. If you touch a battery, clean it with rubbing alcohol. NOTE: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 NOTE: • Battery at an acceptable charge level • The vehicle must be equipped with an automatic • transmission to be equipped with Remote Start. • • Obstructions between the vehicle and RKE transmitter • may reduce this range.
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Remote Start Abort Message On Electronic Vehicle Information Center (EVIC) — If Equipped To Enter Remote Start Mode The following messages will display in the EVIC if the vehicle fails to remote start or exits remote start prematurely: Press and release the REMOTE START button on the RKE transmitter twice within five seconds. The vehicle doors will lock, parking lights will flash and the horn will chirp twice (if programmed).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 • For security, power window and power sunroof op- To Exit Remote Start Mode And Drive The Vehicle eration (if equipped) are disabled when the vehicle is Before the end of 15-minute cycle, push and release the in the Remote Start mode. UNLOCK button on the RKE transmitter to unlock the • The engine can be started two consecutive times (two doors and disarm the Vehicle Security Alarm (if 15-minute cycles) with the RKE transmitter. However, equipped).
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Door Lock Knob If the door lock knob is down when you shut the door, the door will lock. Therefore, make sure the Key Fob is not inside the vehicle before closing the door. • For personal security and safety in the event of a collision, lock the vehicle doors before you drive as well as when you park and leave the vehicle. • When leaving the vehicle, always remove the Key Fob from the ignition and lock your vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 WARNING! (Continued) • Do not leave the Key Fob in or near the vehicle, or in a location accessible to children, and do not leave the ignition of a vehicle equipped with Keyless Enter-N-Go™ in the ACC or ON/RUN mode. A child could operate power windows, other controls, or move the vehicle. 2 Power Door Locks A power door lock switch is on each front door trim panel. Use this switch to lock or unlock the doors.
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If you press the power door lock switch while the ignition is in the ACC or ON/RUN position, and any front door is open, the power locks will not operate. This prevents you from accidentally locking the Key Fob in the vehicle. Cycling the ignition to the OFF position or closing the door will allow the locks to operate. If a door is open, and the ignition is in the ACC or ON/RUN position, a chime will sound as a reminder to remove the Key Fob.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 Child-Protection Door Lock System — Rear Doors To provide a safer environment for small children riding in the rear seats, the rear doors are equipped with Child-Protection Door Lock system. 2 To Engage Or Disengage The Child-Protection Door Lock System 1. Open the rear door. 2. Insert the tip of the emergency key into the lock and rotate to the LOCK or UNLOCK position. 3. Repeat steps 1 and 2 for the opposite rear door.
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: For emergency exit from the rear seats when the • If wearing gloves on your hands, or if it has been raining on the Passive Entry door handle, the unlock Child-Protection Door Lock System is engaged, manually sensitivity can be affected, resulting in a slower reraise the door lock knob to the unlocked position, roll sponse time. down the window, and open the door using the outside door handle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 To Unlock From The Passenger Side With a valid Passive Entry RKE transmitter within 5 ft (1.5 m) of the passenger door handle, grab the front passenger door handle to unlock all four doors automatically. The interior door panel lock knob will raise when the door is unlocked.
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If one of the vehicle doors is open and the door panel switch is used to lock the vehicle, once all open doors have been closed the vehicle checks the inside and outside of the vehicle for any valid Passive Entry RKE transmitters.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 To Lock The Vehicle’s Doors With one of the vehicle’s Passive Entry RKE transmitters within 5 ft (1.5 m) of the driver or passenger front door handles, press the door handle LOCK button to lock all four doors.
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Do NOT grab the door handle, when pressing the door NOTE: handle lock button. This could unlock the door(s). • After pressing the door handle LOCK button, you must wait two seconds before you can lock or unlock the doors, using either Passive Entry door handle. This is done to allow you to check if the vehicle is locked by pulling the door handle, without the vehicle reacting and unlocking.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 There are single window controls on each passenger door trim panel, which operate the passenger door windows. Power Windows The window controls will operate only when the ignition The window controls on the driver’s door control all the is in the ACC or ON/RUN position. door windows. NOTE: For vehicles equipped with the Uconnect®, the power window switches will remain active for up to 10 minutes after the ignition is cycled to the OFF position.
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) ignition of a vehicle equipped with Keyless Enter-NGo™ in the ACC or ON/RUN mode. Occupants, particularly unattended children, can become entrapped by the windows while operating the power window switches. Such entrapment may result in serious injury or death. AUTO-Down Feature To open the window part way, press the window switch to the first detent and release it when you want the window to stop.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 NOTE: Reset Auto-Up • If the window runs into any obstacle during auto- Should the Auto Up feature stop working, the window closure, it will reverse direction and then go back may need to be reset. To reset Auto Up: down. Remove the obstacle and use the window 1. Make sure the door is fully closed. switch again to close the window. 2.
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Window Lockout Switch The window lockout switch on the driver’s door trim panel allows you to disable the window controls on the rear passenger doors and the rear sunscreen (if equipped). To disable the window controls and the rear sunscreen, press and release the window lockout button (setting it in the DOWN position). To enable the window controls and the rear sunscreen, press and release the window lockout button again (setting it in the UP position).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 open or partially open positions. This is a normal occur- NOTE: The transmission must be in PARK before the rence and can be minimized. If the buffeting occurs with button will operate. the rear windows open, then open the front and rear windows together to minimize the buffeting. If the The trunk lid can be released from buffeting occurs with the sunroof open, adjust the sunoutside the vehicle by pressing the roof opening to minimize the buffeting.
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE With the ignition in the OFF position, the Trunk Open Trunk Emergency Release symbol will display until the trunk is closed. As a security measure, a Trunk Internal Emergency Release Refer to “Keyless Enter-N-Go™” in “Things To Know lever is built into the trunk latching mechanism.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 • Front seat belts incorporate pretensioners that may enhance occupant protection by managing occupant Some of the most important safety features in your energy during an impact event vehicle are the restraint systems: • Active Hood System • Three-point lap and shoulder belts for the driver and all passengers • All seat belt systems (except the driver’s) include Automatic Locking Retractors (ALRs), which lock the • Advanced Front Air Bags for driver and front
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE infant and child restraint systems. For more information on LATCH, refer to Lower Anchors and Tether for CHildren (LATCH). NOTE: The Advanced Front Air Bags have a multistage inflator design. This allows the air bag to have different rates of inflation based on several factors, including the severity and type of collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 If a child from 2 to 12 years old (not in a rear facing child 5. If the air bag system in this vehicle needs to be seat) must ride in the front passenger seat, move the seat modified to accommodate a disabled person, contact the Customer Center. Phone numbers are provided as far back as possible and use the proper child restraint. under ⴖIf You Need Assistanceⴖ. (Refer to “Child Restraints”).
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) WARNING! (Continued) • Being too close to the steering wheel or instrument panel during Advanced Front Air Bag deployment could cause serious injury, including death. Air bags need room to inflate. Sit back, comfortably extending your arms to reach the steering wheel or instrument panel. • Supplemental Side Air Bag Inflatable Curtain (SABIC) and Seat-Mounted Side Air Bags (SAB) also need room to inflate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 Research has shown that seat belts save lives, and they can reduce the seriousness of injuries in a collision. Some of the worst injuries happen when people are thrown from the vehicle. Seat belts reduce the possibility of ejection and the risk of injury caused by striking the inside of the vehicle. Everyone in a motor vehicle should be belted at all times. Lap/Shoulder Belts All seating positions in your vehicle are equipped with lap/shoulder belts.
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • Two people should never be belted into a single seat belt. People belted together can crash into one another in a collision, hurting one another badly. Never use a lap/shoulder belt or a lap belt for more than one person, no matter what their size. Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. Pulling Out The Lap/Shoulder Belt Latch Plate 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 WARNING! • A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you properly. In a sudden stop, you could move too far forward, increasing the possibility of injury. Wear your seat belt snugly.
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • A belt that is worn under your arm is dangerous. Your body could strike the inside surfaces of the vehicle in a collision, increasing head and neck injury. A belt worn under the arm can cause internal injuries. Ribs aren’t as strong as shoulder bones. Wear the belt over your shoulder so that your strongest bones will take the force in a collision. • A shoulder belt placed behind you will not protect you from injury during a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as possible and keep it snug. • A twisted belt may not protect you properly. In a collision, it could even cut into you. Be sure the belt is straight.
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Adjustable Upper Shoulder Belt Anchorage As a guide, if you are shorter than average you will prefer a lower position, and if you are taller than average you will prefer a higher position. When you release the anchorage try to move it up and down to make sure that it is locked in position. In the driver and front passenger seats, the shoulder belt can be adjusted upward or downward to position the belt away from your neck.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 3. Slide the latch plate upward over the folded webbing. The folded webbing must enter the slot at the top of the latch plate. 4. Continue to slide the latch plate up until it clears the folded webbing. Seat Belts In Passenger Seating Positions The seat belts in the passenger seating positions are equipped with Automatic Locking Retractors (ALR) which are used to secure a child restraint system.
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Automatic Locking Retractor Mode (ALR) — If Equipped In this mode, the shoulder belt is automatically prelocked. The belt will still retract to remove any slack in the shoulder belt. The Automatic Locking Mode is available on all passenger-seating positions with a combination lap/shoulder belt. Use the Automatic Locking Mode anytime a child safety seat is installed in a seating position that has a belt with this feature.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 NOTE: These devices are not a substitute for proper seat belt placement by the occupant. The seat belt still must be This vehicle has a safety belt system with an Energy worn snugly and positioned properly. Management feature in the front seating positions to help further reduce the risk of injury in the event of a head-on The pretensioners are triggered by the Occupant Restraint Controller (ORC). Like the air bags, the pretencollision.
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Reminder Light and sounding an intermittent chime. Once the sequence starts, it will continue for the entire duration or until the respective seatbelts are fastened. After the sequence completes, the Seat Belt Reminder Light remains illuminated until the respective seat belts are fastened. The driver should instruct all other occupants to fasten their seat belts.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 Seat Belt Extender Supplemental Restraint System (SRS) — Air Bags If a seat belt is too short even when fully extended and when the adjustable upper shoulder belt anchorage (if so equipped) is in its lowest position, your authorized dealer can provide you with a seat belt extender. This extender should be used only if the existing belt is not long enough. When it is not required, remove the extender and store it.
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: The Driver and Front Passenger Advanced Front Air Bags are certified to the new Federal regulations for Advanced Air Bags. The Advanced Front Air Bags have a multistage inflator design. This allows the air bag to have different rates of inflation based on several factors, including the severity and type of collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 This vehicle is equipped with Supplemental Side Air Bag Inflatable Curtains (SABIC) to protect the driver, front, and rear passengers sitting next to a window. The SABIC air bags are located above the side windows and their covers are labeled: SRS AIRBAG.
62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Front and Side Impact Sensors • Front Seat Belt Pretensioners, Seat Belt Buckle Switch, and Seat Track Position Sensors Advanced Front Air Bag Features The Advanced Front Air Bag system has multistage driver and front passenger air bags. This system provides output appropriate to the severity and type of collision as determined by the Occupant Restraint Controller (ORC), which may receive information from the front impact sensors.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 When the air bag deploys, it opens the seam between the Supplemental Seat-Mounted Side Air Bags (SAB) may front and side of the seat’s trim cover. Each air bag provide enhanced protection to help protect an occupant deploys independently; a left side impact deploys the left air bag only and a right-side impact deploys the right air during a side impact. The SAB is marked with an air bag bag only. label sewn into the outboard side of the front seats.
64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The system includes side impact sensors that are calibrated to deploy the side air bags during impacts that require air bag occupant protection. WARNING! Supplemental Side Air Bag Inflatable Curtains (SABIC) Label Location NOTE: • Air Bag covers may not be obvious in the interior trim, but they will open during air bag deployment. • Being too close to the side air bags during deployment could cause you to be severely injured or killed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 WARNING! (Continued) • Your vehicle is equipped with SABIC air bags, do not have any accessory items installed which will alter the roof, including adding a sunroof to your vehicle. Do not add roof racks that require permanent attachments (bolts or screws) for installation on the vehicle roof. Do not drill into the roof of the vehicle for any reason. SAB and SABIC air bags are a supplement to the seat belt restraint system.
66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Air Bag Deployment Sensors And Controls Occupant Restraint Controller (ORC) and Supplemental Driver Side Knee Air Bag are not expected to reduce the risk of injury in rear, side, or rollover collisions. The ORC is part of a Federally regulated safety system The Advanced Front Air Bags and Supplemental Driver required for this vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 Because air bag sensors measure vehicle deceleration The ORC contains a backup power supply system that over time, vehicle speed and damage by themselves are may deploy the air bags even if the battery loses power or not good indicators of whether or not an air bag should it becomes disconnected prior to deployment. have deployed.
68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Ignoring the Air Bag Warning Light in your instrument panel could mean you won’t have the air bags to protect you in a collision. If the light does not come on as a bulb check when the ignition is first turned on, stays on after you start the vehicle, or if it comes on as you drive, have an authorized dealer service the air bag system immediately.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 Supplemental Driver Side Knee Air Bag. The trim cover separates and folds out of the way allowing the air bag to inflate to the full size. The air bag fully inflates in about 15 to 20 milliseconds. at a very high speed and with such a high force that it could injure you if you are not seated properly, or if items are positioned in the area where the side air bag inflates. This especially applies to children.
70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE positioned in the area where the side curtain air bag event the ORC will determine whether to have the inflates. This especially applies to children. The side Enhanced Accident Response System perform the followcurtain air bag is only about 3-1/2 in (9 cm) thick when ing functions: it is inflated. • Cut off fuel to the engine.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 If A Deployment Occurs The Advanced Front Air Bags are designed to deflate immediately after deployment. However, if you haven’t healed significantly within a few days, or if you have any blistering, see your doctor immediately. • As the air bags deflate, you may see some smoke-like particles. The particles are a normal by-product of the process that generates the non-toxic gas used for air bag inflation.
72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Deployed air bags and seat belt pretensioners cannot protect you in another collision. Have the air bags, seat belt pretensioners, and the front seat belt retractor assemblies replaced by an authorized dealer immediately. Also, have the Occupant Restraint Controller (ORC) system serviced as well. Maintaining Your Air Bag System WARNING! • Modifications to any part of the air bag system could cause it to fail when you need it.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 WARNING! (Continued) • Do not attempt to modify any part of your air bag system. The air bag may inflate accidentally or may not function properly if modifications are made. Take your vehicle to an authorized dealer for any air bag system service. If your seat, including your trim cover and cushion, needs to be serviced in any way (including removal or loosening/tightening of seat attachment bolts), take the vehicle to your authorized dealer.
74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: If the speedometer, tachometer, or any engine related gauges are not working, the Occupant Restraint Controller (ORC) may also be disabled. The air bags may not be ready to inflate for your protection. Promptly check the fuse block for blown fuses. Refer to “Fuses” in “Maintaining Your Vehicle” for the proper air bag fuses. See your authorized dealer if the fuse is good.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 NOTE: EDR data are recorded by your vehicle only if a non-trivial crash situation occurs; no data are recorded by the EDR under normal driving conditions and no personal data (e.g., name, gender, age, and crash location) are recorded. However, other parties, such as law enforcement, could combine the EDR data with the type of personally identifying data routinely acquired during a crash investigation.
76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards. You should also make sure that you can install it in the vehicle where you will use it. NOTE: • For additional information, refer to www.seatcheck.org or call 1–866–SEATCHECK. Canadian residents should refer to Transport Canada’s website for additional information: • http://www.tc.gc.ca/eng/roadsafety/safedriverschildsafety-index-53.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77 Summary Of Recommendations For Restraining Children In Vehicles Infants and Toddlers Small Children Larger Children Children Too Large for Child Restraints Child Size, Height, Weight Or Age Children who are two years old or younger and who have not reached the height or weight limits of their child restraint Children who are at least two years old or who have out-grown the height or weight limit of their rear-facing child restraint Children who have out-g
78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE their infant carrier but are still less than at least two years old. Children should remain rearward-facing until they Safety experts recommend that children ride rearwardreach the highest weight or height allowed by their facing in the vehicle until they are two years old or until convertible child seat. they reach either the height or weight limit of their rear facing child safety seat.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 79 the vehicle’s seat cushion while the child’s back is against Children who are two years old or who have outgrown the seatback, they should use a belt-positioning booster their rear-facing convertible child seat can ride forward- seat. The child and belt-positioning booster seat are held in the vehicle by the seat belt. facing in the vehicle.
80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • After a child restraint is installed in the vehicle, do not move the vehicle seat forward or rearward because it can loosen the child restraint attachments. Remove the child restraint before adjusting the vehicle seat position. When the vehicle seat has been adjusted, reinstall the child restraint. • When your child restraint is not in use, secure it in the vehicle with the seat belt or LATCH anchorages, or remove it from the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 81 4. Is the lap part of the belt as low as possible, touching the child’s thighs and not their stomach? 5. Can the child stay seated like this for the whole trip? If the answer to any of these questions was “no,” then the child still needs to use a booster seat in this vehicle. If the child is using the lap/shoulder belt, check belt fit periodically and make sure the seat belt buckle is latched. A child’s squirming or slouching can move the belt out of position.
82 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Recommendations For Attaching Child Restraints Restraint Type Combined Weight of the Child + Child Restraint Rear-Facing Child Restraint Rear-Facing Child Restraint Forward-Facing Child Restraint Forward-Facing Child Restraint Up to 65 lbs (29.5 kg) More than 65 lbs (29.5 kg) Up to 65 lbs (29.5 kg) More than 65 lbs (29.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 83 Lower Anchors And Tethers For Children (LATCH) Restraint System Your vehicle is equipped with the child restraint anchorage system called LATCH, which stands for Lower Anchors and Tethers for CHildren. The LATCH system has three vehicle anchor points for installing LATCHequipped child seats. There are two lower anchorages located at the back of the seat cushion where it meets the seatback and one top tether anchorage located behind the seating position.
84 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE LATCH Positions For Installing Child Restraints In This Vehicle Lower Anchorage Symbol 2 anchorages per seating position Top Tether Anchorage Symbol
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 85 What is the weight limit (child’s weight + weight of the child restraint) for using the LATCH anchorage system to attach the child restraint? 65 lbs (29.
86 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Can two child restraints be attached using a common lower LATCH anchorage? No Can the rear-facing child restraint touch the back of the front passenger seat? Yes Can the head restraints be removed? Yes, center position only. Never “share” a LATCH anchorage with two or more child restraints.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 87 Locating The LATCH Anchorages The lower anchorages are round bars that are found at the rear of the seat cushion where it meets the seatback, below the anchorage symbols on the seatback. They are just visible when you lean into the rear seat to install the child restraint. You will easily feel them if you run your finger along the gap between the seatback and seat cushion.
88 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Locating The LATCH Anchorages There are tether strap anchorages behind each rear seating position located in the panel between the rear seatback and the rear window. They are found under a plastic cover with the tether anchorage symbol on it. Tether Strap Anchorages LATCH-compatible child restraint systems will be equipped with a rigid bar or a flexible strap on each side.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 89 tether strap. The tether strap will have a hook at the end Always follow the directions of the child restraint to attach to the top tether anchorage and a way to tighten manufacturer when installing your child restraint. Not the strap after it is attached to the anchorage. all child restraint systems will be installed as described here.
90 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Place the child seat between the lower anchorages for 6. Tighten all of the straps as you push the child restraint that seating position. For some second row seats, you rearward and downward into the seat. Remove slack may need to recline the seat and/or raise the head in the straps according to the child restraint manufacrestraint to get a better fit. If the rear seat can be moved turer’s instructions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 91 behind the child restraint, route the seat belt through the child restraint belt path and then buckle it. Do not lock the seatbelt. Remind all children in the vehicle that the seat belts are not toys and that they should not play with them. WARNING! • Improper installation of a child restraint to the LATCH anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed.
92 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belt Systems for Installing Child Restraints in this Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 93 What is the weight limit (child’s weight + weight of the child restraint) for using the Tether Anchor with the seat belt to attach a forward facing child restraint? Can the rear-facing child restraint touch the back of the front passenger seat? Weight limit of the Child Restraint Can the head restraints be removed? Can the buckle stalk be twisted to tighten the seat belt against the belt path of the child restraint? Yes, center position only.
94 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Installing A Child Restraint With A Switchable Automatic Locking Retractor (ALR) 4. Pull on the webbing to make the lap portion tight against the child seat. 1. Place the child seat in the center of the seating 5. To lock the seat belt, pull down on the shoulder part of position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 95 8. If the child restraint has a top tether strap and the seating position has a top tether anchorage, connect the tether strap to the anchorage and tighten the tether strap. See the section “Installing Child Restraints Using the Top Tether Anchorage” for directions to attach a tether anchor. 9. Test that the child restraint is installed tightly by pulling back and forth on the child seat at the seat belt path. It should not move more than 1 inch (25.
96 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 5. If the child restraint has a top tether strap and the seating position has a top tether anchorage, connect the tether strap to the anchorage and tighten the tether strap. Refer to “Installing Child Restraints Using The Top Tether Anchorage” for directions to attach a tether anchor. away from the child restraint. Repeat steps 4 to 6, above, to complete the installation of the child restraint.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 97 2. Rotate or lift the cover to access the anchor directly behind the seat where you are placing the child restraint. 2 3. Route the tether strap to provide the most direct path for the strap between the anchor and the child seat. If your vehicle is equipped with adjustable rear head restraints, raise the head restraint, and where possible, route the tether strap under the head restraint and between the two posts.
98 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Adjustable Headrest Downward Position Tether Strap Mounting 1 — Cover 3 — Attaching Strap A — Tether Strap Hook B — Tether Anchor 4. Attach the tether strap hook of the child restraint to the top tether anchorage as shown in the diagram.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 99 5. Remove slack in the tether strap according to the child Transporting Pets restraint manufacturer’s instructions. Air Bags deploying in the front seat could harm your pet. An unrestrained pet will be thrown about and possibly WARNING! injured, or injure a passenger during panic braking or in • An incorrectly anchored tether strap could lead to a collision. increased head motion and possible injury to the child.
100 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE While cruising, brief full-throttle acceleration within the limits of local traffic laws contributes to a good break-in. However, wide-open throttle acceleration in low gear can be detrimental and should be avoided. NOTE: A new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered a normal part of the break-in and not interpreted as an indication of difficulty.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 101 WARNING! (Continued) WARNING! (Continued) • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • Be sure everyone in your vehicle is in a seat and using a seat belt properly. eventually poison you.
102 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Whenever a change is noticed in the sound of the exhaust system, when exhaust fumes can be detected inside the vehicle, or when the underside or rear of the vehicle is damaged, have a competent mechanic inspect the complete exhaust system and adjacent body areas for broken, damaged, deteriorated, or mispositioned parts. Open seams or loose connections could permit exhaust fumes to seep into the passenger compartment.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 103 feel the air directed against the windshield. See your authorized dealer for service if your defroster is inoperable. Floor Mat Safety Information Always use floor mats designed to fit the footwell of your vehicle. Use only floor mats that leave the pedal area unobstructed and that are firmly secured so that they cannot slip out of position and interfere with the pedals or impair safe operation of your vehicle in other ways.
104 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • Always make sure that objects cannot fall into the driver footwell while the vehicle is moving. Objects can become trapped under the brake pedal and accelerator pedal causing a loss of vehicle control. • If required, mounting posts must be properly installed, if not equipped from the factory.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 䡵 MIRRORS . . . . . . . . . . . . . . . . . . . . . . . . . . . .112 ▫ Automatic Dimming Mirror . . . . . . . . . . . . . .112 ▫ Outside Mirrors . . . . . . . . . . . . . . . . . . . . . .113 ▫ Outside Mirrors Folding Feature — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . .113 ▫ Power Folding Outside Mirrors — If Equipped. . . . . . . . . . . . . . . . . . . . . . . . . .115 ▫ Heated Mirrors — If Equipped . . . . . . . . . . . .
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 䡵 Uconnect® PHONE (8.4/8.4N) . . . . . . . . . . . . .127 ▫ Power Seats — If Equipped . . . . . . . . . . . . . .179 ▫ Uconnect® 8.4/8.4 Nav . . . . . . . . . . . . . . . . .127 ▫ Power Lumbar — If Equipped . . . . . . . . . . . .181 ▫ Operation . . . . . . . . . . . . . . . . . . . . . . . . . .130 ▫ Heated Seats — If Equipped . . . . . . . . . . . . .182 ▫ Phone Call Features . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 䡵 LIGHTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . .195 ▫ Turn Signals . . . . . . . . . . . . . . . . . . . . . . . . .201 ▫ Headlight Switch . . . . . . . . . . . . . . . . . . . . .195 ▫ Lane Change Assist . . . . . . . . . . . . . . . . . . .202 ▫ Automatic Headlights — If Equipped . . . . . . .196 ▫ High/Low Beam Switch . . . . . . . . . . . . . . . .202 ▫ Headlights On With Wipers (Available With Automatic Headlights Only) . . . . . .
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Headlights On With Wipers (Available With Automatic Headlights Only) . . . . . . . . . . . . .209 ▫ Rain Sensing Wipers . . . . . . . . . . . . . . . . . . .209 䡵 TILT/TELESCOPING STEERING COLUMN . . .211 䡵 POWER TILT/TELESCOPING STEERING COLUMN — IF EQUIPPED . . . . . . . . . . . . . . .212 䡵 HEATED STEERING WHEEL — IF EQUIPPED . .213 䡵 ADJUSTABLE PEDALS — IF EQUIPPED . . . . . .215 䡵 ELECTRONIC SPEED CONTROL — IF EQUIPPED . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 ▫ Overtake Aid . . . . . . . . . . . . . . . . . . . . . . . .236 ▫ Enabling And Disabling ParkSense® . . . . . . . .256 ▫ Adaptive Cruise Control (ACC) Menu . . . . . . .236 ▫ Service The ParkSense® Park Assist System . . .257 ▫ Display Warnings And Maintenance . . . . . . . .237 ▫ Cleaning The ParkSense® System . . . . . . . . . .257 ▫ Precautions While Driving With ACC . . . . . . .239 ▫ ParkSense® System Usage Precautions. . . . . . .
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Programming A Non-Rolling Code . . . . . . . . .269 ▫ Sunshade Operation. . . . . . . . . . . . . . . . . . . .277 ▫ Canadian/Gate Operator Programming . . . . . .270 ▫ Wind Buffeting . . . . . . . . . . . . . . . . . . . . . . .277 ▫ Using HomeLink® . . . . . . . . . . . . . . . . . . . .272 ▫ Sunroof Maintenance . . . . . . . . . . . . . . . . . . .277 ▫ Security . . . . . . . . . . . . . . . . . . . . . . . . . . . .272 ▫ Ignition OFF Operation . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 ▫ Closing Power Shade — Manual Mode . . . . . .281 ▫ Console Features . . . . . . . . . . . . . . . . . . . . .291 ▫ Venting Sunroof — Express . . . . . . . . . . . . . .281 ▫ Door Storage . . . . . . . . . . . . . . . . . . . . . . . . .292 ▫ Pinch Protect Feature . . . . . . . . . . . . . . . . . . .281 ▫ Rear Seat Armrest Storage — If Equipped . . . .293 ▫ Wind Buffeting . . . . . . . . . . . . . . . . . . . . . . .
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Automatic Dimming Mirror This mirror automatically adjusts for headlight glare from vehicles behind you. This feature will be defaulted on, and is only disabled when the vehicle is moving in reverse. NOTE: This feature is disabled when the vehicle is moving in reverse. Automatic Dimming Mirror CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 Outside Mirrors Outside Mirrors Folding Feature — If Equipped To receive maximum benefit, adjust the outside mirror(s) Some models have outside mirrors that are hinged. The to center on the adjacent lane of traffic and a slight hinge allows the mirror to pivot forward and rearward to overlap of the view obtained from the inside mirror. resist damage. The hinge has three detent positions: full forward, full rearward and normal.
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Three of the LEDs are turn signal indicators, which flash with the corresponding turn signal lights in the front and rear of the vehicle. Turning on the Hazard Warning flashers will also activate these LEDs. The fourth LED supplies illuminated entry lighting, which turns on in both mirrors when you use the Remote Keyless Entry (RKE) transmitter or open any door. This LED shines outward to illuminate the front and rear door handles.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 The power mirror controls consist of mirror select butThe power mirror controls are located on the driver’s tons and a four-way mirror control switch. To adjust a mirror, press either the L (left) or R (right) button to select door trim panel. the mirror that you want to adjust. Power Mirrors NOTE: A light in the select button will illuminate indicating the mirror is activated and can be adjusted.
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Press the switch once and the mirrors will fold in, Illuminated Vanity Mirrors — If Equipped pressing the switch a second time will return the mirrors An illuminated vanity mirror is located on the sun visor. to the normal driving position. To use the mirror, rotate the sun visor downward and NOTE: If the vehicle speed is greater than 10 mph swing the mirror cover upward. The light turns on automatically. Closing the mirror cover turns off the light.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 “Slide-On-Rod” And Extender Features Of Sun Visor To use the “Slide-On-Rod” feature of the sun visor, rotate the sun visor downward and swing the sun visor so it is parallel to the side window, grab the sun visor and pull rearwards until the sun visor is in the desired position. To use the extender feature of the sun visor, grab the extender which is located at the rear of the visor and pull rearward.
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE BLIND SPOT MONITORING (BSM) — IF EQUIPPED The Blind Spot Monitoring (BSM) system uses two radarbased sensors, located inside the rear bumper fascia, to detect highway licensable vehicles (automobiles, trucks, motorcycles, etc.) that enter the blind spot zones from the rear/front/side of the vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 vehicle when the vehicle speed reaches approximately 6 m.p.h. (10 km/h) or higher and will alert the driver of vehicles in these areas. NOTE: • The BSM system does NOT alert the driver about rapidly approaching vehicles that are outside the detection zones. • The BSM system detection zone DOES NOT change if your vehicle is towing a trailer. Therefore, visually verify the adjacent lane is clear for both your vehicle and trailer before making a lane change.
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The area on the rear fascia where the radar sensors are located must remain free of snow, ice, and dirt/road contamination so that the BSM system can function properly. Do not block the area of the rear fascia where the radar sensors are located with foreign objects (bumper stickers, bicycle racks, etc.).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 Entering From The Side Entering From The Rear Vehicles that move into your adjacent lanes from either Vehicles that come up from behind your vehicle on either side of the vehicle. side and enter the rear detection zone with a relative speed of less than 30 m.p.h. (48 km/h).
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Overtaking Traffic If you pass another vehicle slowly with a relative speed of less than 15 m.p.h. (24 km/h) and the vehicle remains in the blind spot for approximately 1.5 seconds, the warning light will be illuminated. If the difference in speed between the two vehicles is greater than 15 m.p.h. (24 km/h), the warning light will not illuminate.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 3 Overtaking/Passing The BSM system will not alert you of objects that are traveling in the opposite direction of the vehicle in adjacent lanes.
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! (Continued) system is not designed to detect pedestrians, bicyclists, or animals. Even if your vehicle is equipped with the BSM system, always check your vehicle’s mirrors, glance over your shoulder, and use your turn signal before changing lanes. Failure to do so can result in serious injury or death. Rear Cross Path Opposing Traffic WARNING! The Blind Spot Monitoring system is only an aid to help detect objects in the blind spot zones.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 NOTE: In a parking lot situation, oncoming vehicles can be obscured by vehicles parked on either side. If the sensors are blocked by other structures or vehicles, the system will not be able to alert the driver. When RCP is on and the vehicle is in REVERSE, the driver is alerted using both the visual and audible alarms, including reducing the radio volume.
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE turn signal is then activated, and it corresponds to an alert present on that side of the vehicle, an audible chime Three selectable modes of operation are available in the will also be sounded. Whenever a turn signal and deUconnect® System. Refer to “Uconnect® Settings/ tected object are present on the same side at the same Customer Programmable Features” in “Understanding time, both the visual and audio alerts will be issued.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 2. The device must accept any interference received, including interference that may cause undesired opWhen the BSM system is turned off there will be no eration of the device. visual or audible alerts from either the BSM or RCP Changes or modifications to any of these systems by systems. other than an authorized service facility could void NOTE: The BSM system will store the current operating authorization to use this equipment.
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Hands Free text to speech listening of your incoming • Viewing and Calling contacts from Phonebooks disSMS messages. played on the touchscreen. • Hands Free text messaging (“Send a message to John • Setting Favorite Contact Phone numbers so they are Smith’s Mobile”). easily accessible on the Main Phone screen. • Redialing last dialed numbers (“Redial”). • Viewing and Calling contacts from Recent Call logs.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 Your mobile phone’s audio is transmitted through your vehicle’s audio system; the system will automatically mute your radio when using the Uconnect® Phone. For Uconnect® customer support: • U.S. residents - visit www.UconnectPhone.com or call 1-877-855-8400. WARNING! Any voice commanded system should be used only in safe driving conditions following all applicable laws, including laws regarding phone use.
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE phone and one audio device can be used with the system your vehicle is equipped. Please see the Uconnect® at a time. The system is available in English, Spanish, or Voice Command section for direction on how to use the button. French languages. The Uconnect® Phone is fully integrated with the vehicles audio system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 2. Say the individual commands and allow the system to guide you to complete the task. You will be prompted for a specific command and then guided through the available options. • Prior to giving a voice command, one must wait for the beep, which follows the “Listen” prompt or another prompt. • For certain operations, compound commands can be used.
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Smith.” For multiple inputs in the same phrase or sentence, the system identifies the topic or context and provides the associated follow-up prompt such as “Who do you want to call?” in the case where a phone call was requested but the specific name was not recognized. To activate the Uconnect® Phone from idle, simply press the button on your steering wheel and say a command or say “help.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 NOTE: • You must have Bluetooth® enabled on your mobile phone to complete this procedure. • The vehicle must be in PARK. 3 To complete the pairing process, you will need to reference your mobile phone Owner’s Manual. The Uconnect® website may also provide detailed instructions for pairing. 1. Press the “Phone” soft-key on the screen to begin. 2. If there is no phone currently connected with the system, a pop-up will appear. Mobile Phone Pairing 3.
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Touch the “Add Device” soft-key. • Search for available devices on your Bluetooth® enabled mobile phone. When prompted on the phone, enter the name and PIN shown on the Uconnect® screen. • See step 4 to complete the process. 4. Uconnect® Phone will display an in progress screen while the system is connecting. Mobile Phone Pairing Progress 5.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 NOTE: For phones which are not made a favorite, the phone priority is determined by the order in which it was 1. Touch the “Settings” soft-key from the Phone main paired. The latest phone paired will have the higher screen. priority. 2. Touch the “Add Device” soft-key. You can also use the following VR commands to bring up Pair Additional Mobile Phones 3.
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: If there is no device currently connected with the You can also use the following VR command to bring up system, a pop-up will appear. a list of paired audio devices: 5. Search for available devices on your Bluetooth® en- • “Show Paired Phones” abled audio device. When prompted on the device, • “Connect My Phone” enter the PIN shown on the Uconnect® screen. Connecting To A Particular Mobile Phone Or 6.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 Disconnecting A Phone Or Audio Device 4. The options pop-up will be displayed. 1. Touch the “Settings” soft-key. 5. Touch the “Delete Device” soft-key. 2. Touch the “Paired Phone” or “Audio Device” soft-key. 6. Touch the “X” to exit out of the Settings screen. 3. Touch the “+” soft-key located to the right of the Making A Phone Or Audio Device A Favorite device name. 1. Touch the “Settings” soft-key. 4. The options pop-up will be displayed. 2.
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Phonebook Download (Automatic Phonebook Transfer From Mobile Phone) — If Equipped • A maximum of 1000 entries per phone will be downloaded and updated every time a phone is connected to the Uconnect® Phone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 Managing Your Favorite Phonebook There are three ways you can add an entry to your Favorite Phonebook. 1. During an active call of a number to make a favorite, touch and hold a favorite button on the top of the phone main screen. 2. After loading the mobile phonebook, select phonebook from the Phone main screen, then select the appropriate number. Touch the + next to the selected number to display the options pop-up. In the pop-up select “Add to Favorites.
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE the + on that selected entry. When the Options pop-up To Remove A Favorite appears, touch “Add from Mobile.” You will then be 1. To remove a Favorite, select phonebook from the asked which contact and number to choose from your Phone main screen. mobile phonebook. When complete the new favorite 2. Next select Favorites on the left side of the screen and will be shown. then touch the + Options soft-key. 3.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 Emergency And Towing Assistance The Emergency and Towing Assistance Favorite numbers can only be altered. These cannot be deleted and the names cannot be changed. To change the Emergency or Towing Assistance numbers follow these steps. 1. Touch the “Phonebook” soft-key from the Phone main screen. Remove From Favorites 2. Touch the “Favorites” soft-key. Scroll to the bottom of the list to locate the Emergency and Towing Assistance Favorites. 4.
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Phone Call Features The following features can be accessed through the Uconnect® Phone if the feature(s) are available and supported by Bluetooth® on your mobile service plan. For example, if your mobile service plan provides threeway calling, this feature can be accessed through the Uconnect® Phone. Check with your mobile service provider for the features that you have.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 • Mobile Phonebook • Recent Call Log • SMS Message Viewer 3. The Uconnect® Phone will dial the number associated with John Doe, or if there are multiple numbers it will ask which number you want to call for John Doe. Call Controls Dial By Saying A Number 1. Press the The touchscreen allows you to control the following call button on your steering wheel to begin. features: 2. After the “Listening” prompt and the following beep, • say “Dial 151–1234–5555.
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Touch-Tone Number Entry 1. Touch the “Phone” soft-key. 2. Touch the “Dial” soft-key. 3. The Touch-Tone screen will be displayed. 4. Use the numbered soft-keys to enter the number and touch “Call.” To send a touch tone using Voice Recognition (VR), press button on your steering wheel while in a call the and say “Send 1234#” or you can say “Send Voicemail Password” if Voicemail password is stored in your mobile phonebook.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 These can be accessed by touching the “recent calls” Answer Or Ignore An Incoming Call — Call Currently In Progress soft-key on the Phone main screen. button and say “Show my If a call is currently in progress and you have another You can also press the incoming calls” from any screen and the Incoming incoming call, you will hear the same network tones for call waiting that you normally hear when using your calls will be displayed.
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE phonebooks. To go back to the first call, refer to “Toggling Call Termination Between Calls” in this section. To combine two calls, refer To end a call in progress, momentarily press the butto “Join Calls” in this section. ton on the steering wheel or the “end” soft-key. Only the active call(s) will be terminated and if there is a call Place/Retrieve A Call From Hold on hold, it will become the new active call.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 NOTE: The call will remain within the vehicle audio system until the phone becomes out of range for the Bluetooth® connection. It is recommended to touch the “transfer” soft-key when leaving the vehicle. Uconnect® Phone Features Emergency Assistance instruct the paired mobile phone to call the emergency number. This feature is supported in the U.S., Canada, and Mexico. NOTE: • The Emergency call may also be initiated by using the touchscreen.
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Your phone must be turned on and connected to the Uconnect® Phone to allow use of this vehicle feature in emergency situations, when the mobile phone has network coverage and stays connected to the Uconnect® Phone. Roadside Assistance / Towing Assistance If you need roadside/towing assistance: 1. Press the button on the steering wheel to begin.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 You can use your Uconnect® Phone to access a voice mail system or an automated service, such as a paging service or automated customer service line. Some services require immediate response selection. In some instances, that may be too quick for use of the Uconnect® Phone. You can also send stored mobile phonebook entries as tones for fast and easy access to voice mail and pager entries.
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Some paging and voice mail systems have system time Voice Response Length out settings that are too short and may not allow the It is possible for you to choose between Brief and use of this feature. Detailed Voice Response Length. • sPauses, wait or other characters that are supported by 1. Touch the “More” soft-key (where available), then some phones are not supported over Bluetooth®. touch the “Settings” soft-key.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 Phone And Network Status Indicators WARNING! (Continued) Uconnect® Phone will provide notification to inform you of your phone and network status when you are attempting to make a phone call using Uconnect® Phone. The status is given for network signal strength and phone battery strength. Dialing Using The Mobile Phone Keypad WARNING! Driving while distracted can result in loss of vehicle control, accident and injury.
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Certain brands of mobile phones do not send the dial ring to the Uconnect® Phone to play it on the vehicle audio system, so you will not hear it. Under this situation, after successfully dialing a number the user may feel that the call did not go through even though the call is in progress. Once your call is answered, you will hear the audio.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 Things You Should Know About Your Uconnect® Phone Performance is maximized under: • Low-To-Medium Blower Setting Voice Command • Low-To-Medium Vehicle Speed • For best performance, adjust the rearview mirror to • Low Road Noise provide at least ½ inch (1 cm) gap between the overhead console (if equipped) and the mirror. • Smooth Road Surface • Always wait for the beep before speaking.
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: It is recommended that you do not store names in • your favorites phonebook while the vehicle is in motion. • Phonebook (Mobile and Favorites) name recognition rate • is optimized when the entries are not similar. You can say • “O” (letter “O”) for “0” (zero).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 Voice Text Reply Uconnect® Phone can read or send new messages on your phone. Your phone must support SMS over Bluetooth® to use this feature. If the Uconnect® Phone determines your phone is not compatible with SMS messaging over Bluetooth® the “messaging” button will be grayed out and the feature will not be available for use. 3 Voice Text List NOTE: Uconnect® Phone SMS is only available when the vehicle is not moving.
156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Once a message is received and viewed or listened to, you will have the following options: Read Messages: If you receive a new text message while your phone is connected to Uconnect® Phone, an announcement will • Send a Reply be made to notify you that you have a new text message. • Forward • Call Send Messages Using Soft-Keys: You can send messages using Uconnect® Phone. To send a new message: 1. Touch the “Phone” soft-key. 2.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 Send Messages Using Voice Commands: 1. Press the button. 2. After the “Listening” prompt and the following beep, say “Send message to John Smith mobile.” 3. After the system prompts you for what message you want to send, say the message you wish to send or say “List.” There are 18 preset messages. While the list of defined messages are being read, you can button and interrupt the system by pressing the saying the message you want to send.
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE List of Preset Messages: 1. Yes. 2. No. 3. Okay. 4. I can’t talk right now. 5. Call me. 6. I’ll call you later. 7. I’m on my way. Preset Message List 8. Thanks. 9. I’ll be late. 10. I will be minutes late. 11. See you in minutes.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 12. Stuck in traffic. Bluetooth® Communication Link 13. Start without me. Mobile phones have been found to lose connection to the Uconnect® Phone. When this happens, the connection can generally be re-established by switching the mobile phone OFF/ON. Your mobile phone is recommended to remain in Bluetooth® ON mode. 14. Where are you? 15. Are you there yet? 16. I need directions. 17. I’m lost. 18. See you later.
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Tree
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 6. Send dial tones for automated systems is available while a call is active. This is an example that uses a You can replace “John Smith” with any name in your Phonebook Record named “Voicemail Password.” mobile or favorite phone book. You can also say “Send a message to John Smith” and the system will ask you 7.
162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 NOTE: 5. You can replace “248 555 1212” with any phone number supported by your Mobile phone. 1. You can replace “John Smith” with any name in your mobile or favorite phone book. You can also say “Send 6. You can replace “4” with any message number shown a message to John Smith” and the system will ask you on the screen. which phone number you want to send a message to 7. If your phone does not support phonebook download for John Smith.
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 NOTE: Available Voice Commands are shown in bold VOICE COMMAND face and underlined in the gray shaded boxes. Uconnect® 8.4/8.4 Nav General Information The Uconnect® Voice Command system allows This device complies with Part 15 of the FCC rules and you to control your AM, FM radio, satellite RSS 210 of Industry Canada. Operation is subject to the radio, disc player, SD Card, USB/iPod® and following conditions: SiriusXM Travel Link.
166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Any voice commanded system should be used only in safe driving conditions following all applicable laws, including laws regarding phone use. Your attention should be focused on safely operating the vehicle. Failure to do so may result in a collision causing serious injury or death. If no command is spoken the system will say one of two responses: • I didn’t understand • I didn’t get that, etc.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 The system will be interrupted, and after the beep, you At any point, if the system does not recognize one of your can say a command. This will become helpful once you commands, you will be prompted to repeat it. start to learn the options. To hear available commands, press the Uconnect® Voice button and say “Help.” You will hear NOTE: At any time, you can say the words “Cancel” or Command available commands for the screen displayed. “Help.
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The system handles multiple inputs in the same phrase or sentence such as “make a phone call” and “to Kelly Smith.” For multiple inputs in the same phrase or sentence, the system identifies the topic or context and provides the associated follow-up prompt such as “Who do you want to call?” in the case where a phone call was requested but the specific name was not recognized.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 Changing The Volume Starting Voice Recognition (VR) Session In Radio/Player Modes 1. Start a dialogue by pressing the Voice Command In this mode, you can say the following commands: button. NOTE: The commands can be said on any screen when a call is not active after pushing the Uconnect® Voice 3. Use the ON/OFF VOLUME rotary knob to adjust the button. Command volume to a comfortable level while the Voice Command system is speaking.
170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Tree
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 NOTE: • You can replace “950 AM” with any other AM or FM frequency, such as “98.7 FM.” • You can replace “80’s on 8” with any other satellite station name received by the radio. • You can replace “8” with any other satellite channel number received by the radio. • You can replace “rock” with any of the satellite music types. NOTE: Available Voice Commands are shown in bold face and shaded grey.
172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173 NOTE: • You can replace the album, artist, song, genre, playlist, podcast and audio book names with any corresponding names on the current device that is playing. • You can replace “8” with any track on the CD that is currently playing. Command is only available when CD is playing. • Playlist, Podcast and audio book commands are only available when the iPod® is connected and playing.
174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175 NOTE: • You can replace “NFL” with any league shown on the sports league screen. For example you can say “Show MLB headlines” or “Show PGA headlines.” • You can replace “Headlines” with any menu items shown on a league screen. For example you can say “Show NFL Schedule and results” or “Show NCAA Basketball AP top 25” or “Show Major League Baseball Teams.
176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177 NOTE: • Only available with Navigation equipped vehicles. • You can replace “Player” with “Radio,” “Navigation,” “Phone,” “Climate,” “More” or “Settings.” • Navigation commands only work if equipped with Navigation. NOTE: Available Voice Commands are shown in bold face and shaded grey.
178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179 NOTE: • You can also say “Find City,” “Find Favorite,” “Find Play by Category,” “Find Play by Name,” “Find Recently Found,” “Where to?” or “Go Home.” • You can say “Find Nearest” then “Restaurant,” “Fuel,” “Transit,” “Lodging,” “Shopping,” “Bank,” “Entertainment,” “Recreation,” “Attractions,” “Community,” “Auto Services,” “Hospitals,” “Parking,” “Airport,” “Police Stations,” “Fire Stations,” or “Auto Dealers.
180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The passenger’s seat will move up or down, Adjusting The Seat Forward Or Rearward forward or rearward. The seat can be adjusted both forward and rearward. Push the seat switch forward or rearward, the seat will move in the direction of the switch. Release the switch when the desired position has been reached. Adjusting The Seat Up Or Down The height of the seats can be adjusted up or down.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181 Reclining The Seatback WARNING! (Continued) The angle of the seatback can be adjusted forward or rearward. Push the seatback switch forward or rearward, the seat will move in the direction of the switch. Release the switch when the desired position is reached. WARNING! • Adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death.
182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE power seat. Push the switch forward or rearward to increase or decrease the lumbar support. Push the switch upward or downward to raise or lower the lumbar support. Heated Seats — If Equipped On some models, the front and rear seats may be equipped with heaters in both the seat cushions and seatbacks. The front driver and passenger heated seats are operated using the Uconnect® System.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 183 WARNING! (Continued) • Do not place anything on the seat or seatback that insulates against heat, such as a blanket or cushion. This may cause the seat heater to overheat. Sitting in a seat that has been overheated could cause serious burns due to the increased surface temperature of the seat. Front Heated Seats When the HI-level setting is selected, the heater will provide a boosted heat level during the first four minutes of operation.
184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE This feature can be programmed through the Uconnect® If the HI-level heating is selected, the system will autosystem. Refer to “Uconnect® Settings” in “Understand- matically switch to LO-level heating after approximately 60 minutes of continuous operation. At that time, the ing Your Instrument Panel” for further information. number of indicators illuminated changes from two to Rear Heated Seats one, indicating the change.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 185 The front ventilated seats control buttons are located This feature can be programmed through the Uconnect® within the climate or controls screen of the touchscreen. system. Refer to “Uconnect® Settings” in “Understanding Your Instrument Panel” for further information. once to choose • Press the ventilated seat button HIGH. Head Restraints • Press the ventilated seat button choose LOW. • Press the ventilated seat button turn the ventilated seat OFF.
186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Active Head Restraints — Front Seats The front driver and passenger seats are equipped with Active Head Restraints (AHR). In the event of a rear impact the AHRs will automatically extend forward minimizing the gap between the back of the occupants head and the AHR. The AHRs will automatically return to their normal position following a rear impact. If the AHRs do not return to their normal position see your authorized dealer immediately.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 187 WARNING! Do not place items over the top of the Active Head Restraint, such as coats, seat covers or portable DVD players. These items may interfere with the operation of the Active Head Restraint in the event of a collision and could result in serious injury or death. Rear Head Restraints The center head restraint has two adjustable positions, up or down. When the center seat is being occupied the head restraint should be in the raised position.
188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: These loops can be tucked away when not in use. Folded Rear Seatback Rear Seatback Loop After releasing the seatback, it can be folded forward. When the seatback is folded to the upright position, make sure it is latched by strongly pulling on the top of the seatback above the seat strap.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 189 WARNING! • Be certain that the seatback is securely locked into position. If the seatback is not securely locked into position, the seat will not provide the proper stability for child seats and/or passengers. An improperly latched seat could cause serious injury. • The cargo area in the rear of the vehicle (with the rear seatbacks in the locked-up or folded down position) should not be used as a play area by children when the vehicle is in motion.
190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Adjust all memory profile settings to desired preferences (i.e., seat, side mirror, adjustable pedals [if equipped], power tilt and telescopic steering column [if equipped], and radio station presets). 3. Press and release the S (Set) button on the memory switch. 4. Within five seconds, memory buttons (1) Information Center memory position has Memory Seat Switch Programming The Memory Feature To create a new memory profile, perform the following: 1.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 191 3. Once the profile has been recalled, press and release the SET (S) button on the memory switch, then press and release button (1) or (2) accordingly. “Memory Your RKE transmitters can be programmed to recall one Profile Set” (1 or 2) will display in the instrument of two pre-programmed memory profiles by pressing the cluster. UNLOCK button on the RKE transmitter. 4.
192 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To recall the memory settings for driver one, press MEMORY button number (1) on the driver’s door or the UNLOCK button on the RKE transmitter linked to memory position 1. Easy Entry/Exit Seat This feature provides automatic driver seat positioning to enhance driver mobility when entering and exiting the vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 193 • The Easy Entry/Easy Exit feature is disabled when the driver seat position is less than 0.9 in (22.7 mm) forward of the rear stop. At this position, there is no benefit to the driver by moving the seat for Easy Exit or Easy Entry. Each stored memory setting will have an associated Easy Entry and Easy Exit position. NOTE: The Easy Entry/Exit feature is not enabled when the vehicle is delivered from the factory.
194 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! To prevent possible damage, do not slam the hood to close it. Lower the hood until it is open approximately 6 in (15 cm), and then drop it. This should secure both latches. Never drive your vehicle unless the hood is fully closed, with both latches engaged. WARNING! Hood Safety Latch Use the hood prop rod (if equipped) to secure the hood in the open position. Be sure the hood is fully latched before driving your vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 195 LIGHTS Headlight Switch The headlight switch is located on the left side of the instrument panel. This switch controls the operation of the headlights, parking lights, instrument panel lights, instrument panel light dimming, interior lights and fog lights. 3 Headlight Switch Rotate the headlight switch clockwise to the first detent for parking light and instrument panel light operation.
196 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Headlights — If Equipped This system automatically turns the headlights on or off according to ambient light levels. To turn the system on, rotate the headlight switch counterclockwise to the AUTO position. When the system is on, the headlight time delay feature is also on. This means the headlights will stay on for up to 90 seconds after you place the ignition into the OFF position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 197 If you turn the headlights or parking lights on, or place Automatic High Beam Headlamp Control — If the ignition in ACC or RUN, the system will cancel the Equipped delay. The Automatic High Beam Headlamp Control system If you turn the headlights off before the ignition, they will provides increased forward lighting at night by automating high beam control through the use of a digital camera turn off in the normal manner. mounted on the inside rearview mirror.
198 UNDERSTANDING THE FEATURES OF YOUR VEHICLE and other obstructions on the windshield or camera To Deactivate lens will cause the system to function improperly. 1. Pull the multifunction lever toward you (or rearward If the windshield or Automatic High Beam Headlamp in car) to manually deactivate the system (normal Control mirror is replaced, the mirror must be re-aimed operation of low beams). to ensure proper performance. See your local authorized 2.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 199 • The Adaptive Headlight System is active only when NOTE: If allowed by law in the country in which the vehicle was purchased the Daytime Running Lights can the vehicle is moving forward. be turned on and off using the Uconnect® System, refer The Adaptive Headlight System can be turned On or Off to “Uconnect® Settings” in “Understanding Your Instruusing the Uconnect® System, refer to “Uconnect® Setment Panel” for further information.
200 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Fog Lights — If Equipped The rear fog light switch is built into the headlight switch. To activate the rear fog lights, turn the headlamp switch to the park lamp or headlamp position. Press the headlight switch once for front fog lights, press the switch a second time for front and rear fog lights. Pressing the switch a third time will deactivate the rear fog lights, and a fourth time will deactivate the front fog lights.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 201 Multifunction Lever Turn Signals The multifunction lever controls the operation of the turn Move the multifunction lever up or down and the arrows signals, headlight beam selection and passing lights. The on each side of the instrument cluster flash to show multifunction lever is located on the left side of the proper operation of the front and rear turn signal lights. steering column.
202 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Lane Change Assist Front Map/Reading Lights — If Equipped Tap the lever up or down once, without moving beyond The front map/reading lights are mounted in the overthe detent, and the turn signal (right or left) will flash head console. three times then automatically turn off. High/Low Beam Switch Push the multifunction lever away from you to switch the headlights to high beam. Pull the multifunction lever toward you to switch the headlights back to low beam.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 203 second time. The lights will also turn on when the Courtesy Lights UNLOCK button on the Remote Keyless Entry (RKE) is The courtesy lights can be turned on by pressing the top pressed. corner of the lens. To turn the lights off, press the lens a second time.
204 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Ambient Light — If Equipped Interior Lights The overhead console is equipped with an ambient light The interior lights come on when a door is opened. feature. This light casts illumination for improved visibilTo protect the battery, the interior lights will turn off ity of the floor and center console area. automatically 10 minutes after the ignition is moved to the LOCK position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 205 3 Dimmer Controls With the parking lights or headlights on, rotating the left dimmer control upward will increase the brightness of the instrument panel lights and lighted cupholders (if equipped).
206 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Ambient Light Control Dome Light Position Rotate the right dimmer control upward or downward to Rotate the left dimmer control completely upward to the increase or decrease the brightness of the door handle second detent to turn on the interior lights. The interior lights and ambient light located in the overhead console. lights will remain on when the dimmer control is in this position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 207 WINDSHIELD WIPERS AND WASHERS Intermittent Wiper System The multifunction lever operates the windshield wipers and washer when the ignition is placed in the ON/RUN or ACC position. The multifunction lever is located on the left side of the steering column. Use the intermittent wiper when weather conditions make a single wiping cycle with a variable pause between cycles desirable.
208 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! • Turn the windshield wipers off when driving through an automatic car wash. Damage to the windshield wipers may result if the wiper control is left in any position other than off. • In cold weather, always turn off the wiper switch and allow the wipers to return to the “Park” position before turning off the engine.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 209 If you activate the washer while the windshield wiper control is in the delay range, the wipers will operate for two wipe cycles after releasing the lever and then resume the intermittent interval previously selected.
210 UNDERSTANDING THE FEATURES OF YOUR VEHICLE from the windshield washers of the vehicle ahead. Rotate NOTE: the end of the multifunction lever to one of four settings • The Rain Sensing feature will not operate when the to activate this feature. wiper speed is in the low or high position. The sensitivity of the system can be adjusted with the • The Rain Sensing feature may not function properly multifunction lever.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 211 vehicle speed becomes greater than 0 mph (0 km/h) or the outside temperature rises above freezing. • Neutral Wipe Inhibit — The Rain Sensing feature will not operate when the ignition is placed in the RUN position, the transmission shift lever is in the NEUTRAL position and the vehicle speed is less than 5 mph (8 km/h), unless the wiper control on the multifunction lever is moved or the shift lever is moved out of the NEUTRAL position.
212 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Do not adjust the steering column while driving. Adjusting the steering column while driving or driving with the steering column unlocked, could cause the driver to lose control of the vehicle. Failure to follow this warning may result in serious injury or death. POWER TILT/TELESCOPING STEERING COLUMN — IF EQUIPPED This feature allows you to tilt the steering column Power Tilt/Telescoping Steering Switch upward or downward.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 213 NOTE: For vehicles equipped with Driver Memory Seat, you can use your Remote Keyless Entry (RKE) transmitter or the memory switch on the driver’s door trim panel to return the tilt/telescopic steering column to preprogrammed positions. Refer to “Driver Memory Seat” in this section. WARNING! Do not adjust the steering column while driving.
214 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Controls Soft-Key Heated Steering Wheel Soft-Key NOTE: The engine must be running for the heated steering wheel to operate.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 215 Vehicles Equipped With Remote Start WARNING! (Continued) On models that are equipped with remote start, the heated steering wheel can be programmed to come on during a remote start through the Uconnect® system. Refer to “Uconnect® Settings” in “Understanding Your Instrument Panel” for further information. • Do not place anything on the steering wheel that insulates against heat, such as a blanket or steering wheel covers of any type and material.
216 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Press the switch rearward to move the pedals rearward (toward the driver). • The pedals can be adjusted with the ignition OFF. • The pedals cannot be adjusted when the vehicle is in REVERSE or when the Electronic Speed Control System is on.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 217 • For vehicles equipped with Driver Memory Seat, you WARNING! can use your Remote Keyless Entry (RKE) transmitter or the memory switch on the driver’s door trim panel Do not adjust the pedals while the vehicle is moving. to return the adjustable pedals to pre-programmed You could lose control and have an accident. Always positions. Refer to “Driver Memory Seat” in “Under- adjust the pedals while the vehicle is parked.
218 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: In order to ensure proper operation, the Electronic Speed Control System has been designed to shut down if multiple Speed Control functions are operated at the same time. If this occurs, the Electronic Speed Control System can be reactivated by pushing the Electronic Speed Control ON/OFF button and resetting the desired vehicle set speed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 219 WARNING! Leaving the Electronic Speed Control system on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the system OFF when you are not using it.
220 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The speed increment shown is dependant on the speed of To Decrease Speed U.S. (mph) or Metric (km/h) units: When the Electronic Speed Control is set, you can decrease speed by pushing the SET (-) button. U.S. Speed (mph) • Pressing the RES (+) button once will result in a 1 mph The speed decrement shown is dependant on the speed increase in set speed. Each subsequent tap of the of U.S. (mph) or Metric (km/h) units: button results in an increase of 1 mph. U.S.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 221 • If the button is continually pressed, the set speed will continue to decrease until the button is released, then the new set speed will be established. To Accelerate For Passing Press the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. Using Electronic Speed Control On Hills WARNING! Electronic Speed Control can be dangerous where the system cannot maintain a constant speed.
222 UNDERSTANDING THE FEATURES OF YOUR VEHICLE need to reset your cruise control. ACC utilizes a radar sensor designed to detect a vehicle directly ahead of you. NOTE: • If the sensor does not detect a vehicle ahead of you, ACC will maintain a fixed set speed. • If the ACC sensor detects a vehicle ahead, ACC will apply limited braking or acceleration (not to exceed the original set speed) automatically to maintain a preset following distance, while matching the speed of the vehicle ahead.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 223 WARNING! (Continued) WARNING! (Continued) • Cannot take street, traffic, and weather conditions into account, and may be limited upon adverse sight distance conditions. • Does not always fully recognize complex driving conditions, which can result in wrong or missing distance warnings. • Can only apply a maximum of 40% of the vehicle’s braking capability, and will not bring the vehicle to a complete stop.
224 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The system will not react to preceding vehicles. Always be aware of the mode selected. You can change the mode by using the Cruise Control buttons. The two control modes function differently. Always confirm which mode is selected. Adaptive Cruise Control (ACC) Operation The speed control buttons (located on the right side of the steering wheel) operates the ACC system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 225 NOTE: Any chassis/suspension modifications to the NOTE: You cannot enable ACC under the following vehicle will effect the performance of the Adaptive Cruise conditions: Control. • When you apply the brakes. Activating Adaptive Cruise Control (ACC) • When the parking brake is set. You can only activate ACC if the vehicle speed is above • When the automatic transmission is in PARK, RE20 mph (32 km/h). VERSE or NEUTRAL.
226 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Adaptive Cruise Control (ACC) Ready To turn the system OFF, push and release the ON/OFF button again. At this time, the system will turn off and the EVIC will display “Adaptive Cruise Control Off.” Adaptive Cruise Control (ACC) OFF WARNING! Leaving the Adaptive Cruise Control (ACC) system on when not in use is dangerous.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 227 WARNING! (Continued) want. You could lose control and have a collision. Always leave the system off when you are not using it. 3 To Set A Desired ACC Speed When the vehicle reaches the speed desired, push the SET - button and release. The EVIC will display the set speed. ACC Set Remove your foot from the accelerator pedal. If you do not, the vehicle may continue to accelerate beyond the set speed.
228 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The system will not be controlling the distance be- To Cancel tween your vehicle and the vehicle ahead. The vehicle The system will disable ACC without erasing the speed will only be determined by the position of the memory if: accelerator pedal. • You softly tap the brake pedal. • You depress the brake pedal. • You press the CANCEL switch. • The vehicle speed goes below 15 mph (25 km/h). • An Anti-Lock Brake System (ABS) event occurs.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 229 To Resume Speed Press the RES + button and release. Then remove your foot from the accelerator pedal. The EVIC will display the last set speed. NOTE: You can resume ACC from a minimum of 20 mph (32 km/h). WARNING! Adaptive Cruise Control (ACC) Cancelled To Turn Off The system will turn off and erase the set speed in memory if: • You push and release the ON/OFF button. • You turn OFF the ignition.
230 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Vary The Speed Setting Metric Speed (km/h) To Increase Speed • RES + button once will result in a 2 km/h increase in set speed. Each subsequent tap of the button results in an increase of 2 km/h. While ACC is set, you can increase the set speed by pressing the RES + button. The speed increment shown is dependant on the speed of • If the button is continually pressed, the set speed will continue to increase in 10 km/h increments until the U.S.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 231 The speed decrement shown is dependant on the speed • If the button is continually pressed, the set speed will of U.S. (mph) or Metric (km/h) units: continue to decrease in 10 km/h increments until the button is released. The decrease in set speed is reU.S. Speed (mph) flected in the EVIC display. • Pressing the SET - button once will result in a 1 mph NOTE: decrease in set speed.
232 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Setting The Following Distance In ACC The specified following distance for ACC can be set by varying the distance setting between 3 (long), 2 (medium), and 1 (short). Using this distance setting and the vehicle speed, ACC calculates and sets the distance to the vehicle ahead. This distance setting displays in the EVIC.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 233 same lane, the EVIC displays the “Sensed Vehicle Indicator” icon, and the system adjusts vehicle speed automatically to maintain the distance setting, regardless of the set speed. The vehicle will then maintain the set distance until: • The vehicle ahead accelerates to a speed above the set speed. • The vehicle ahead moves out of your lane or view of the sensor.
234 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The maximum braking applied by ACC is limited; however, the driver can always apply the brakes manually, if necessary. NOTE: The brake lights will illuminate whenever the ACC system applies the brakes. A Proximity Warning will alert the driver if ACC predicts that its maximum braking level is not sufficient to maintain the set distance.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 235 3 Brake Alert 2 Brake Alert 1
236 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Overtake Aid Adaptive Cruise Control (ACC) Menu When driving with ACC engaged and following a target vehicle, the system will provide an additional acceleration to assist in passing vehicles in front. This additional acceleration is triggered when the driver utilizes the left turn signal. In locations with left hand drive traffic, Overtake Aid is active only when passing on the left hand side of the Target vehicles.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 237 Adaptive Cruise Control Ready • System Off • When ACC is activated but the vehicle speed setting • ACC Proximity Warning has not been selected, the display will read “Adaptive • ACC Unavailable Warning Cruise Control Ready.” • The EVIC will return to the last display selected after ACC SET five seconds of no ACC display activity. • When ACC is set, the set speed will display.
238 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The “Clean Radar Sensor In Front Of Vehicle” message can sometimes be displayed while driving in highly reflective areas (i.e. tunnels with reflective tiles, or ice and snow). The ACC system will recover after the vehicle has left these areas. Under rare conditions, when the radar is not tracking any vehicles or objects in its path this warning may temporarily occur.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 239 When the condition that deactivated the system is no longer present, the system will return to the “Adaptive Cruise Control Off” state and will resume function by simply reactivating it. NOTE: Installing a vehicle front-end protector or an aftermarket grille or modifying the grille is not recommended. Doing so may block the sensor and inhibit ACC operation.
240 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Adding A Trailer Hitch The weight of a trailer/hitch may affect the performance of ACC. If there is a noticeable change in performance following the installation of a trailer/hitch, or if the ACC performance does not return to normal after removing the trailer/hitch see your authorized dealer. Offset Driving ACC may not detect a vehicle in the same lane that is offset from your direct line of travel, or a vehicle merging in from a side lane.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 241 Using ACC On Hills When driving on hills, ACC may not detect a vehicle in your lane. Depending on the speed, vehicle load, traffic conditions, and the steepness of the hills, ACC performance may be limited. Turn Or Bend Example ACC may occasionally provide braking and/or a driver alert that you consider unnecessary. This may be the system’s response to signs, guardrails, and other stationary objects in a curve. This may also occur at the base of steep hills.
242 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Lane Changing ACC may not detect a vehicle until it is completely in the lane in which you are traveling. In the illustration shown, ACC has not yet detected the vehicle changing lanes and it may not detect the vehicle until it’s too late for the ACC system to take action. ACC may not detect a vehicle until it is completely in the lane. There may not be sufficient distance to the lane-changing vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 243 Narrow Vehicles Stationary Objects And Vehicles Some narrow vehicles traveling near the outer edges of the lane or edging into the lane are not detected until they have moved fully into the lane. There may not be sufficient distance to the vehicle ahead. ACC does not react to stationary objects and stationary vehicles.
244 UNDERSTANDING THE FEATURES OF YOUR VEHICLE General Information FCC Requirements For Vehicular Radar Systems Classification Specifications: 47 C.F.R. Part 15 47 C.F.R Part 15.515 Normal (Fixed Speed) Cruise Control Mode In addition to Adaptive Cruise Control mode, a normal (fixed speed) Cruise Control mode is available for cruising at fixed speeds. The normal Cruise Control mode is designed to maintain a set cruising speed without requiring the driver to operate the accelerator.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 245 • If the button is continually pressed, the set speed will continue to increase until the button is released, then When the vehicle reaches the speed desired, press the the new set speed will be established. SET - button and release. The EVIC will display the set speed. Metric Speed (km/h) To Set A Desired Speed NOTE: You must observe the display when setting or • Pressing the RES + button once will result in a 2 km/h changing speed, not the speedometer.
246 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The speed decrement shown is dependant on the speed • If the button is continually pressed, the set speed will of U.S. (mph) or Metric (km/h) units: continue to decrease until the button is released, then the new set speed will be established. U.S. Speed (mph) To Cancel • Pressing the SET - button once will result in a 1 mph decrease in set speed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 247 FCW monitors the information from the forward looking sensor as well as the Electronic Brake Controller (EBC), The system will turn off and erase the set speed in wheel speed sensors, i.e., to calculate a probable rear-end memory if: collision. When the system determines that a rear-end • You push and release the ON/OFF button. collision is probable a warning message (both audible and visual) will be displayed on the EVIC. When the • You turn off the ignition.
248 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! (Continued) vehicle via braking and steering. Failure to follow this warning could lead to serious injury or death. Changing FCW Status setting provides less reaction time than the “Far” setting, which allows for a more dynamic driving experience. Changing the FCW status to “Off” prevents the system from warning you of a possible collision with the vehicle in front of you.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 249 FCW Unavailable Warning If the system turns off, and the EVIC displays “ACC/ FCW Unavailable, Service Required”, there may be a temporary malfunction that limits FCW functionality. Although the vehicle is still drivable under normal conditions, FCW will be temporarily unavailable. If this occurs, try activating FCW again later, following a key cycle. If the problem persists, see your authorized dealer.
250 UNDERSTANDING THE FEATURES OF YOUR VEHICLE PARKSENSE® FRONT AND REAR PARK ASSIST — IF EQUIPPED The ParkSense® Park Assist system provides visual and audible indications of the distance between the rear and/or front fascia and a detected obstacle when backing up or moving forward, e.g. during a parking maneuver. Refer to ParkSense® System Usage Precautions for limitations of this system and recommendations.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 251 ParkSense® Warning Display The ParkSense® Warning screen will only be displayed if Sound and Display is selected from the Uconnect® System. Refer to “Uconnect® Settings” in “Understanding Your Instrument Panel” for further information. 3 The ParkSense® Warning screen is located within the Electronic Vehicle Information Center (EVIC).
252 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ParkSense® Display The warning display will turn ON indicating the system status when the vehicle is in REVERSE or when the vehicle is in DRIVE and an obstacle has been detected. Park Assist System OFF Park Assist System ON The system will indicate a detected obstacle by showing three solid arcs and will produce a one-half second tone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 253 3 Slow Tone Fast Tone
254 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The vehicle is close to the obstacle when the EVIC display shows one flashing arc and sounds a continuous tone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 255 Rear Distance (in/cm) Front Distance (in/cm) Audible Alert (Chime) Greater than 59 in (150 cm) Greater than 47 in (120 cm) None Arc None WARNING ALERTS 59-39 in 39-25 in (150-100 cm) (100-65 cm) 47-39 in 39-25 in (120-100 cm) (100-65 cm) Single 1/2 secSlow (for rear ond tone (for only) rear only) 3 Solid 3 Slow Flashing (Continuous) 25-12 in (65-30 cm) 25-12 in (65-30 cm) Fast Less than 12 in (30 cm) Less than 12 in (30 cm) Continuous 2 Slow Flashing 1
256 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Front Park Assist Audible Alerts Enabling And Disabling ParkSense® ParkSense® will turn off the Front Park Assist audible alert (chime) after approximately three seconds when an obstacle has been detected, the vehicle is stationary, and brake pedal is applied. ParkSense® can be enabled and disabled using the Uconnect® System. The available choices are: Off, Sound Only, or Sound and Display.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 257 and/or front fascia/ bumper is clean and clear of snow, ice, mud, dirt or other obstruction and then cycle the During vehicle start up, when the ParkSense® Park ignition. If the message continues to appear see an Assist system has detected a fault condition, the Elecauthorized dealer.
258 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Jackhammers, large trucks, and other vibrations could • Ensure the ParkSense® system is OFF if objects such as affect the performance of ParkSense®. bicycle carriers, trailer hitches, etc. are placed within 30 cm from the rear fascia/ bumper. Failure to do so can • When you turn ParkSense® off, the EVIC will display result in the system misinterpreting a close object as a “PARK ASSIST SYSTEM OFF.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 259 CAUTION! (Continued) WARNING! • The vehicle must be driven slowly when using ParkSense® in order to be able to stop in time when an obstacle is detected. When backing up, it is recommended that the driver looks over his/her shoulder when using ParkSense®. • Drivers must be careful when backing up even when using the ParkSense® Park Assist system.
260 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! (Continued) • Before using the ParkSense® Park Assist system, it is strongly recommended that the ball mount and hitch ball assembly is disconnected from the vehicle when the vehicle is not used for towing. Failure to do so can result in injury or damage to vehicles or obstacles because the hitch ball will be much closer to the obstacle than the rear fascia when the warning display turns on the single flashing arc and sounds the continuous tone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 261 NOTE: The ParkView® Rear Back Up Camera has programmable modes of operation that may be selected through the Uconnect® System. Refer to “Uconnect® Settings” in “Understanding Your Instrument Panel” for further information. When the static grid lines have been programmed to turn on, they will illustrate the width of the vehicle and will show separate zones that will help indicate the distance to the rear of the vehicle.
262 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! • To avoid vehicle damage, ParkView® should only be used as a parking aid. The ParkView® camera is unable to view every obstacle or object in your drive path. • To avoid vehicle damage, the vehicle must be driven slowly when using ParkView® to be able to stop in time when an obstacle is seen. It is recommended that the driver look frequently over his/her shoulder when using ParkView®.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 263 To turn the lights off, press the switch a second time. The Lights are mounted in the overhead console. Each light lights also turn on when a door is opened. The lights will can be turned on by pressing the switch on either side of also turn on when the UNLOCK button on the RKE is pressed. the console. These buttons are backlit for night time visibility.
264 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Courtesy Lights Sunglasses Bin Door The courtesy lights can be turned on by pressing the top At the front of the console a compartment is provided for corner of the lens. To turn the lights off, press the lens a the storage of a pair of sunglasses. The storage compartsecond time. ment access is a “push/push” design. Push the chrome pad on the door to open. Push the chrome pad on the door to close.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 265 GARAGE DOOR OPENER — IF EQUIPPED HomeLink® replaces up to three hand-held transmitters that operate devices such as garage door openers, motorized gates, lighting or home security systems. The HomeLink® unit is powered by your vehicles 12 Volt battery. 3 The HomeLink® buttons, located on either the overhead console, headliner or sunvisor, designate the three different HomeLink® channels. The HomeLink® indicator is located above the center button.
266 UNDERSTANDING THE FEATURES OF YOUR VEHICLE For more efficient programming and accurate transmission of the radio-frequency signal it is recommended that a new battery be placed in the hand-held transmitter of the device that is being programmed to the HomeLink® system. Erase all channels before you begin programming. To erase the channels place the ignition in the ON/RUN position and press and hold the two outside HomeLink® buttons (I and III) for up 20 seconds or until the red indicator flashes.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 267 Programming A Rolling Code For programming garage door openers that were manufactured after 1995. These garage door openers can be identified by the “LEARN” or “TRAIN” button located where the hanging antenna is attached to the garage door opener. It is NOT the button that is normally used to open and close the door. The name and color of the button may vary by manufacturer. 3 Training The Garage Door Opener 1 — Door Opener 2 — Training Button 1.
268 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) away from the HomeLink® button you wish to program while keeping the HomeLink® indicator light in view. Firmly press and release the “LEARN” or “TRAINING” button. On some garage door openers/devices there may be a light that blinks when the garage door opener/device is in the LEARN/TRAIN mode. 3.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 269 2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) away from the HomeLink® button you wish to proTo reprogram a channel that has been previously trained, gram while keeping the HomeLink® indicator light in follow these steps: view. 1. Cycle the ignition to the ON/RUN position. 3. Simultaneously press and hold both the Homelink® 2.
270 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • To program the two remaining HomeLink® buttons, Canadian/Gate Operator Programming repeat each step for each remaining button. DO NOT For programming transmitters in Canada/United States erase the channels. that require the transmitter signals to “time-out” after several seconds of transmission.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 271 2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) away from the HomeLink® button you wish to program while keeping the HomeLink® indicator light in view. • To program the two remaining HomeLink® buttons, repeat each step for each remaining button. DO NOT erase the channels. 3.
272 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Using HomeLink® Troubleshooting Tips To operate, press and release the programmed HomeLink® button. Activation will now occur for the programmed device (i.e., garage door opener, gate operator, security system, entry door lock, home/office lighting, etc.,). The hand-held transmitter of the device may also be used at any time.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 273 WARNING! WARNING! (Continued) Vehicle exhaust contains carbon monoxide, a dangerous gas. Do not run your vehicle in the garage while programming the transceiver. Exhaust gas can cause serious injury or death. use a garage door opener without these safety features. Call toll-free 1–800–355–3515 or, on the Internet at www.HomeLink.com for safety information or assistance.
274 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: POWER SUNROOF — IF EQUIPPED • The transmitter has been tested and it complies with The power sunroof switch is located between the sun FCC and IC rules. Changes or modifications not ex- visors on the overhead console. pressly approved by the party responsible for compliance could void the user’s authority to operate the device.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 275 WARNING! WARNING! (Continued) • Never leave children unattended in a vehicle, or with access to an unlocked vehicle. Never leave the Key Fob in or near the vehicle, or in a location accessible to children. Do not leave the ignition of a vehicle equipped with Keyless Enter-N-Go™ in the ACC or ON/RUN mode. Occupants, particularly unattended children, can become entrapped by the power sunroof while operating the power sunroof switch.
276 UNDERSTANDING THE FEATURES OF YOUR VEHICLE movement. The sunroof and sunshade will remain in a Pinch Protect Feature partially opened condition until the switch is pushed and This feature will detect an obstruction in the opening of held rearward again. the sunroof during Express Close operation. If an obstruction in the path of the sunroof is detected, the Closing Sunroof — Express sunroof will automatically retract.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 277 Sunshade Operation Sunroof Maintenance The sunshade can be opened manually. However, the Use only a nonabrasive cleaner and a soft cloth to clean sunshade will open automatically as the sunroof opens. the glass panel. NOTE: The sunshade cannot be closed if the sunroof is Ignition OFF Operation open. The power sunroof switch will remain active for up to approximately ten minutes after the ignition switch is Wind Buffeting turned to the LOCK position.
278 UNDERSTANDING THE FEATURES OF YOUR VEHICLE COMMANDVIEW® SUNROOF WITH POWER SHADE — IF EQUIPPED The CommandView® sunroof switch is located to the left between the sun visors on the overhead console. The power shade switch is located to the right between the sun visors on the overhead console.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 279 WARNING! WARNING! (Continued) • Never leave children unattended in a vehicle, or with access to an unlocked vehicle. Never leave the Key Fob in or near the vehicle, or in a location accessible to children. Do not leave the ignition of a vehicle equipped with Keyless Enter-N-Go™ in the ACC or ON/RUN mode. Occupants, particularly unattended children, can become entrapped by the power sunroof while operating the power sunroof switch.
280 UNDERSTANDING THE FEATURES OF YOUR VEHICLE movement. The sunroof and sunshade will remain in a Opening Power Shade — Express partially opened condition until the switch is pushed and Press the shade switch rearward and release it within held rearward again. one-half second and the shade will automatically open to the halfway position and stop automatically.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 281 Closing Power Shade — Express Venting Sunroof — Express Press the switch forward and release it within one-half second and the shade will close automatically from any position. If the sunroof is completely closed the shade will close fully and stop automatically. This is called “Express Close”. During Express Close operation, any movement of the switch will stop the shade.
282 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: If three consecutive sunroof close attempts result Ignition OFF Operation in Pinch Protect reversals, the fourth close attempt will be The power sunroof switch will remain active for up to a Manual Close movement with Pinch Protect disabled. approximately ten minutes after the ignition switch is turned to the LOCK position. Opening either front door Wind Buffeting will cancel this feature.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 283 NOTE: To ensure proper operation, a MOPAR® knob and element must be used. CAUTION! • Do not exceed the maximum power of 160 Watts (13 Amps) at 12 Volts. If the 160 Watts (13 Amps) power rating is exceeded, the fuse protecting the system will need to be replaced. • Power outlets are designed for accessory plugs only. Do not insert any other object in the power outlets as this will damage the outlet and blow the fuse.
284 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The center console outlet is powered directly from the battery (power available at all times). Items plugged into this outlet may discharge the battery and/or prevent the engine from starting. There is also a 12 Volt power outlet located on the back of the center console for rear passengers. This power outlet has power available only when the ignition is placed in the ACC or RUN position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 285 WARNING! To avoid serious injury or death: • Only devices designed for use in this type of outlet should be inserted into any 12 Volt outlet. • Do not touch with wet hands. • Close the lid when not in use and while driving the vehicle. • If this outlet is mishandled, it may cause an electric shock and failure.
286 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! CAUTION! (Continued) • Many accessories that can be plugged in draw power from the vehicle’s battery even when not in use (i.e., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting. • Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.) will degrade the battery even more quickly.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 287 3 Retractable Cover Front Cupholders Heated And Cooled Cupholders — If Equipped Your vehicle may be equipped with heated and cooled cupholders. The cupholders are designed to help keep warm beverages warm and cold beverages cool.
288 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! When using the cupholder in the “Hot” position, avoid contact with the heated portion of the cupholder in order to reduce the possibility of burns. Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injuries, medication, alcohol use, exhaustion or other physical condition must exercise particular care in order to prevent serious burn injury.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 289 convenient access to beverage cans or bottles while Lighted Cupholders — If Equipped maintaining a resting place for the rear occupant’s el- On some vehicles the rear cupholders are equipped with bows. a light ring that illuminates the cupholders for the rear passengers. The light ring is controlled by the Dimmer Control. Refer to “Lights” in “Understanding The Features Of Your Vehicle” for further information.
290 UNDERSTANDING THE FEATURES OF YOUR VEHICLE STORAGE Glove Compartment The glove compartment is located on the passenger side of the instrument panel.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 291 Console Features There is a cubby bin located forward of the shift lever. The cubby bin is covered with a push-push actuated door. Push inward on the door to open it, push the door a second time to close it. 3 Two separate storage compartments are also located underneath the center console armrest.
292 UNDERSTANDING THE FEATURES OF YOUR VEHICLE like CDs and tissue boxes. In addition, the 12 volt power outlet, USB and Aux jack are located here. WARNING! Do not operate this vehicle with a console compartment lid in the open position. Driving with the console compartment lid open may result in injury in a collision. Door Storage The door panels contain storage areas.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 293 Rear Seat Armrest Storage — If Equipped For rear passengers there is a storage bin located in the armrest. Lift upward on the latch to open the storage compartment.
294 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Cargo Area — Vehicles Equipped With 60/40 Split-Folding Rear Seat The 60/40 split-folding rear seat provides cargo-carrying versatility. The seatbacks fold down easily by pulling nylon tabs between the seatbacks and the bolsters. When the seats are folded down, they provide a continuous, nearly-flat extension of the load floor.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 295 WARNING! The weight and position of cargo and passengers can change the vehicle center of gravity and vehicle handling. To avoid loss of control resulting in personal injury, follow these guidelines for loading your vehicle: • Always place cargo evenly on the cargo floor. Put heavier objects as low and as far forward as possible. • Place as much cargo as possible in front of the rear axle.
296 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Cargo Net The rear cargo area is equipped with a cargo net. Grocery Bag Hooks CAUTION! Do not exceed the maximum weight limit 50 lbs (22 kg) of the grocery bag hook. Damage may occur to hook and mounting surface.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 297 REAR WINDOW FEATURES Rear Window Defroster The rear window defroster button is located on the climate control. Press this button to turn on the rear window defroster and the heated outside mirrors (if equipped). An indicator in the button will illuminate when the rear window defroster is on. The rear window defroster automatically turns off after approximately 10 minutes. For an additional five minutes of operation, press the button a second time.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 INSTRUMENT PANEL FEATURES . . . . . . . . . .301 ▫ Gear Shift Indicator (GSI) — If Equipped . . . . .321 䡵 INSTRUMENT CLUSTER . . . . . . . . . . . . . . . . .302 ▫ Oil Change Required . . . . . . . . . . . . . . . . . .323 䡵 INSTRUMENT CLUSTER DESCRIPTIONS . . . . .303 ▫ Fuel Economy . . . . . . . . . . . . . . . . . . . . . . . .324 䡵 ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) . . . . . . . . . . . . . . . . . . . . . . .
300 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Turn Menu OFF. . . . . . . . . . . . . . . . . . . . . . .332 䡵 STEERING WHEEL AUDIO CONTROLS . . . . . .352 䡵 Uconnect® SETTINGS . . . . . . . . . . . . . . . . . . .332 ▫ Radio Operation . . . . . . . . . . . . . . . . . . . . . .353 ▫ Hard-Keys . . . . . . . . . . . . . . . . . . . . . . . . . .332 ▫ CD Player . . . . . . . . . . . . . . . . . . . . . . . . . . .354 ▫ Soft-Keys . . . . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 301 INSTRUMENT PANEL FEATURES 4 1 2 3 4 5 6 7 — Air Outlet — Instrument Cluster — Hazard Switch — Uconnect® System — Climate Control Hard Controls — Glove Compartment — ESC Off Switch 8 — Uconnect® System Hard Controls 9 — SD Memory Card Slot 10 — Power Outlet 11 — CD/DVD Slot 12 — Storage Compartment 13 — Engine Start/Stop Button 14 — Trunk Release Button 15 16 17 18 19 — Dimmer Controls — Hood Release — Headlight Switch — Analog Clock — Paddle Shifters
302 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER
UNDERSTANDING YOUR INSTRUMENT PANEL 303 INSTRUMENT CLUSTER DESCRIPTIONS 1. Tachometer 4. Front Fog Light Indicator — If Equipped This indicator will illuminate when the front fog lights are on. The red segments indicate the maximum permissible engine revolutions per minute (RPM x 1000) for each gear range. 5. High Beam Indicator Before reaching the red area, ease up on the accelerator. This indicator shows that the high beam headlights are on.
304 UNDERSTANDING YOUR INSTRUMENT PANEL The Shift Lever Indicator is self-contained within the your odometer needs to be repaired or serviced, the repair technician should leave the odometer reading EVIC displauy. It displays the gear position of the automatic transmission. the same as it was before the repair or service.
UNDERSTANDING YOUR INSTRUMENT PANEL 305 by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.
306 UNDERSTANDING YOUR INSTRUMENT PANEL replacement or alternate tires and wheels allow the TPMS monitors engine and automatic transmission control systo continue to function properly. tems. The light will illuminate when the key is in the ON/RUN position, before engine start. If the bulb does not come on when turning the key from OFF to ON/ CAUTION! RUN, have the condition checked promptly. The TPMS has been optimized for the original equipment tires and wheels.
UNDERSTANDING YOUR INSTRUMENT PANEL 307 WARNING! A malfunctioning catalytic converter, as referenced above, can reach higher temperatures than in normal operating conditions. This can cause a fire if you drive slowly or park over flammable substances such as dry plants, wood, cardboard, etc. This could result in death or serious injury to the driver, occupants or others. 9. Speedometer Indicates vehicle speed. 10.
308 UNDERSTANDING YOUR INSTRUMENT PANEL 13. Sport Shifting electronic controlled damping system. This system reduces body roll and pitch in many driving situations including cornering, acceleration and braking. When Track Mode is Selected, the EVIC will display “Track Mode Activated (Suspension and Transmission)”. In addition to SPORT suspension, Track mode also affects transmission shifting. Refer to “AutoStick” in “Starting And Operating” for further information.
UNDERSTANDING YOUR INSTRUMENT PANEL 309 If the ABS light is on, the brake system should be serviced 18. Brake Warning Light as soon as possible to restore the benefits of Anti-Lock This light monitors various brake functions, brakes. If the ABS light does not turn on when the including brake fluid level and parking brake ignition switch is turned to the ON/RUN position, have application. If the brake light turns on it may the light inspected by an authorized dealer.
310 UNDERSTANDING YOUR INSTRUMENT PANEL The dual brake system provides a reserve braking capacity in the event of a failure to a portion of the hydraulic system. A leak in either half of the dual brake system is indicated by the Brake Warning Light, which will turn on when the brake fluid level in the master cylinder has dropped below a specified level. The light will remain on until the cause is corrected.
UNDERSTANDING YOUR INSTRUMENT PANEL 311 The light also will turn on when the parking brake is (kilometers) at speeds greater than 30 mph (48 km/h), see applied with the ignition switch in the ON/RUN posi- your authorized dealer as soon as possible to have the problem diagnosed and corrected. tion. NOTE: This light shows only that the parking brake is NOTE: applied. It does not show the degree of brake application.
312 UNDERSTANDING YOUR INSTRUMENT PANEL The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, When the ignition switch is first turned to ON/ or when towing a trailer. It should not be allowed to RUN, this light will turn on for four to eight seconds as a bulb check. During the bulb check, if exceed the upper limits of the normal operating range. the driver’s seat belt is unbuckled, a chime will sound.
UNDERSTANDING YOUR INSTRUMENT PANEL 313 WARNING! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call an authorized dealer for service if your vehicle overheats. If you decide to look under the hood yourself, see “Maintaining Your Vehicle”. Follow the warnings under the Cooling System Pressure Cap paragraph.
314 UNDERSTANDING YOUR INSTRUMENT PANEL • Digital Vehicle Speed • Trip Info • Tire Pressure The system allows the driver to select information by pressing the following buttons mounted on the steering wheel: • Vehicle Info Messages • Stored Warning Messages • Turn Menu OFF EVIC Steering Wheel Buttons
UNDERSTANDING YOUR INSTRUMENT PANEL 315 UP Button BACK Button Press and release the UP button to scroll upPress the BACK button to return to the main menu from an info screen or sub-menu item. ward through the main menu and Vehicle Info and Trip Info sub-menus (Fuel Economy, Vehicle Info, Tire PSI, Cruise, Messages) and Electronic Vehicle Information Center (EVIC) sub-menus. Displays DOWN Button The EVIC display consists of three sections: Press and release the DOWN button to scroll 1.
316 UNDERSTANDING YOUR INSTRUMENT PANEL messages that consist of approximately 60 possible warn- of this message type are ⬙Turn Signal On⬙ (if a turn signal ing or information messages. These pop up messages fall is left on) and ⬙Lights On⬙ (if driver leaves the vehicle). into several categories: • Unstored Messages Until RUN • Five Second Stored Message These messages deal primarily with the Remote Start When the appropriate conditions occur, this type of feature.
UNDERSTANDING YOUR INSTRUMENT PANEL 317 EVIC White Telltales This area will show reconfigurable white caution telltales. These telltales include: • Shift Lever Status • Electronic Speed Control SET This telltale will illuminate when the electronic speed control is SET. For further information, refer to “Electronic Speed Control” in “Understanding The Features Of Your Vehicle.
318 UNDERSTANDING YOUR INSTRUMENT PANEL EVIC Amber Telltales • Low Fuel Telltale This area will show reconfigurable amber caution telltales. These telltales include: When the fuel level reaches approximately 3.0 gal (11.0 L) this light will turn on, and remain on until fuel is added. • Forward Collision Warning (FCW) OFF This telltale informs the driver that the For- • Windshield Washer Fluid Low Indicator ward Collision Warning feature is Off.
UNDERSTANDING YOUR INSTRUMENT PANEL 319 Do not operate the vehicle until the cause is corrected. This area will show reconfigurable red telltales. These This light does not show how much oil is in the engine. The engine oil level must be checked under the hood. telltales include: • Charging System Telltale • Door Ajar EVIC Red Telltales This telltale shows the status of the electrical This telltale turns on when one or more doors charging system. If the telltale stays on or comes are ajar.
320 UNDERSTANDING YOUR INSTRUMENT PANEL • Electronic Throttle Control (ETC) Telltale • Engine Temperature Warning Telltale This telltale informs you of a problem with the This telltale warns of an overheated engine condition. As temperatures rise and the gauge apElectronic Throttle Control (ETC) system. If the telltale comes on while driving, have the sys- proaches H, or 260°F, this telltale will illuminate and a tem checked by an authorized dealer. single chime will sound after reaching a set threshold.
UNDERSTANDING YOUR INSTRUMENT PANEL 321 • Transmission Temperature Warning Telltale WARNING! This telltale indicates that the transmission fluid temperature is running hot. This may If the Transmission Temperature Warning Telltale is occur with severe usage, such as trailer towing. illuminated and you continue operating the vehicle, If this telltale turns on, safely pull over and in some circumstances you could cause the fluid to stop the vehicle.
322 UNDERSTANDING YOUR INSTRUMENT PANEL has been reached. This indication notifies the driver that When the shift down indicator (-) is shown on the changing gear will allow a reduction in fuel consump- display, the GSI is advising the driver to engage a lower tion. gear. When the shift up indicator (+) is shown on the display, the GSI is advising the driver to engage a higher gear.
UNDERSTANDING YOUR INSTRUMENT PANEL 323 The GSI indicator in the EVIC remains illuminated until MENU button. To reset the oil change indicator system the driver changes gear, or the driving conditions return (after performing the scheduled maintenance), perform to a situation where changing gear is not required to the following procedure: improve fuel consumption. 1.
324 UNDERSTANDING YOUR INSTRUMENT PANEL Fuel Economy Press and release the UP or DOWN button until ⬙Fuel Economy⬙ is highlighted. Press the SELECT button and the next screen will display the following: • Average Fuel Economy • Distance To Empty (DTE) • Miles Per Gallon (MPG) Average Fuel Economy / ECO Fuel Saver Mode — If Equipped Shows the average fuel economy since the last reset. When Average Fuel Economy is selected, The word ⬙RESET>⬙ (with right arrow) appears next to it.
UNDERSTANDING YOUR INSTRUMENT PANEL 325 When the DTE value is less than 30 miles (48 km) estimated driving distance, the DTE display will change to a “LOW FUEL” message. This display will continue until the vehicle runs out of fuel. Adding a significant amount of fuel to the vehicle will turn off the “LOW Distance To Empty (DTE) FUEL” message and a new DTE value will display. Press Shows the estimated distance that can be traveled with the BACK button to return to the main menu.
326 UNDERSTANDING YOUR INSTRUMENT PANEL ACC/Cruise Control — If Equipped Press and release the UP or DOWN button until ⬙ACC⬙ (if equipped with Adaptive Cruise Control) or ⬙Cruise⬙ is highlighted in the EVIC. Status of the ACC or Cruise is displayed in the menu line also. Press and release the SELECT (right arrow) button to display the following information: feature is in the EVIC main display, the Cruise status will be displayed in place of the EVIC odometer line.
UNDERSTANDING YOUR INSTRUMENT PANEL 327 Trip Info Trip B Press and release the UP or DOWN button until ⬙Trip Shows the total distance traveled for Trip B since the last Info⬙ is highlighted in the EVIC. Press and release the reset. SELECT button to display the following three trip feaElapsed Time tures in the next screen: Shows the total elapsed time of travel since the last reset. • Trip A Elapsed time will increment when the ignition is in the ON/RUN position.
328 UNDERSTANDING YOUR INSTRUMENT PANEL Tire PSI Press and release the UP or DOWN button until ⬙Tire PSI⬙ is highlighted in the EVIC. Press and release the SELECT button and one of the following will be displayed: • If tire pressure is OK for all tires a vehicle ICON is displayed with tire pressure values in each corner of the ICON. • If one or more tires have low pressure, ⬙Tire Pressure LOW⬙ is displayed with the vehicle ICON and the tire pressure values in each corner of the ICON.
UNDERSTANDING YOUR INSTRUMENT PANEL 329 The Performance Features include the following: The following describes each feature and its operation: • 0-60 mph (0-100 km/h) Timers • Braking Distance 0-60 mph (0-100 km/h) • 1/8 Mile When selected, this screen displays the time it takes for the vehicle to go from 0 to 60 mph (0 to 100 km/h) within 10 seconds. • 1/4 Mile • Instantaneous G-Force • Peak G-Force • The feature will “ready” when the vehicle speed is at 0 mph (0 km/h).
330 UNDERSTANDING YOUR INSTRUMENT PANEL • The distance and speed measurements will continue to display until the conditions are met for another event When selected, this screen displays the vehicle’s braking to be recorded. distance and the speed at which the brake pedal was depressed. • Pressing the SELECT button will clear the current run and prepare the cluster to record a new run. • This feature will only function when applying the brakes at speeds above 30 mph (48 km/h).
UNDERSTANDING YOUR INSTRUMENT PANEL 331 SELECT button and Coolant Temp will be displayed. Press the UP or DOWN button to scroll through the When selected, this screen displays the current G-Force following information displays. (lateral and longitudinal). • Coolant Temp Peak G-Force Displays the actual coolant temperature. When selected, this screen displays all four G-Force • Oil Temperature values (two lateral and two longitudinal).
332 UNDERSTANDING YOUR INSTRUMENT PANEL Messages # Hard-Keys Select from Main Menu using the UP or DOWN buttons. This feature shows the number of stored warning messages (in the # place holder). Pressing the RIGHT arrow button will allow you to see what the stored messages are. Pressing the BACK button takes you back to the Main Menu. Hard-Keys are located below the Uconnect® system in the center of the instrument panel.
UNDERSTANDING YOUR INSTRUMENT PANEL 333 release the preferred setting until a check-mark appears • Display Brightness With Headlights ON next to the setting, showing that setting has been seWhen in this display, you may select the brightness with lected. the headlights on.
334 UNDERSTANDING YOUR INSTRUMENT PANEL language soft-key until a check-mark appears next to the • Touchscreen Beep language, showing that setting has been selected. Touch When in this display, you may turn on or shut off the the back arrow soft-key to return to the previous menu. sound heard when a touchscreen button (soft-key) is • Units pressed.
UNDERSTANDING YOUR INSTRUMENT PANEL 335 • Fuel Saver Display In Cluster — If Equipped Clock The “ECO” message is located in the instrument cluster display, this message can be turned on or off. To make your selection, touch the “Fuel Saver Display” soft-key, until a check-mark appears next to the setting, showing that setting has been selected. Touch the back arrow soft-key to return to the previous menu. After pressing the Clock soft-key the following settings will be available.
336 UNDERSTANDING YOUR INSTRUMENT PANEL • Set Time Minutes soft-key until a check-mark appears next to setting, indicating that the setting has been selected. Touch the When in this display, you may adjust the minutes. The back arrow soft-key to return to the previous menu. “Sync with GPS Time” soft-key must be unchecked. To make your selection touch the “+” or “–” soft-keys to Safety & Driving Assistance adjust the minutes up or down.
UNDERSTANDING YOUR INSTRUMENT PANEL 337 For further information, refer to “Adaptive Cruise Con- chime volume settings include “LOW,” “MEDIUM,” and trol (ACC)” in “Understanding The Features Of Your “HIGH.” The factory default volume setting is MEDIUM. Vehicle”. • Rear Park Assist Volume — If Equipped • Park Assist — If Equipped Rear Park Assist chime volume settings can be selected The ParkSense® system will scan for objects behind the from the EVIC or Uconnect® System (if equipped).
338 UNDERSTANDING YOUR INSTRUMENT PANEL • Blind Spot Alert — If Equipped When this feature is selected, the Blind Spot Alert feature can be set to Off, Lights or Lights and Chime. The Blind Spot Alert feature can be activated in “Lights” mode. When this mode is selected, the Blind Spot Monitor (BSM) system is activated and will only show a visual alert in the outside mirrors.
UNDERSTANDING YOUR INSTRUMENT PANEL 339 until a check-mark appears next to setting, showing that next to setting, showing that setting has been selected. setting has been selected. Touch the back arrow soft-key Touch the back arrow soft-key to return to the previous menu. to return to the previous menu. • Rain Sensing Auto Wipers — If Equipped Lights When this feature is selected, the system will automatically activate the windshield wipers if it senses moisture on the windshield.
340 UNDERSTANDING YOUR INSTRUMENT PANEL • Headlight Illumination On Approach to setting, showing that setting has been selected. Press the back arrow button on the touchscreen to return to the When this feature is selected, the headlights will activate previous menu. and remain on for 0, 30, 60, or 90 seconds when the doors are unlocked with the Remote Keyless Entry (RKE) • Auto Dim High Beams — If Equipped transmitter.
UNDERSTANDING YOUR INSTRUMENT PANEL 341 press the “Daytime Running Lights” button on the touchscreen, until a check-mark appears next to setting, showing that setting has been selected. Press the back arrow button on the touchscreen to return to the previous menu. To make your selection, press the “Flash Lamps with Lock” button on the touchscreen, until a check-mark appears next to setting, showing that setting has been selected.
342 UNDERSTANDING YOUR INSTRUMENT PANEL • Flash Lamps With Lock • Sound Horn With Remote Start When this feature is selected, the front and headlights will flash when the doors are locked or unlocked with the Remote Keyless Entry (RKE) transmitter. To make your selection, touch the Flash Lights With Lock soft-key, until a check-mark appears next to setting, showing that setting has been selected. Touch the back arrow soft-key to return to the previous menu.
UNDERSTANDING YOUR INSTRUMENT PANEL 343 NOTE: If the vehicle is programmed 1st Press Of Key Fob Unlocks, all doors will unlock no matter which Passive Entry equipped door handle is grasped. If 1st Press Of Key Fob Unlocks is programmed, only the driver’s door will unlock when the driver’s door is grasped. With Passive Entry, if 1st Press Of Key Fob Unlocks is programmed touching the handle more than once will only result in the driver’s door opening.
344 UNDERSTANDING YOUR INSTRUMENT PANEL Seats soft-key, until a check-mark appears next to setting, showing that setting has been selected. Touch the back After pressing the Auto-On Comfort & Remote Start arrow soft-key to return to the previous menu. soft-key the following settings will be available. Engine Off Options • Sound Horn With Remote Start Auto-On Comfort & Remote Start When this feature is selected, the horn will sound when the remote start is activated.
UNDERSTANDING YOUR INSTRUMENT PANEL 345 equipped), and power outlets will remain active for up to 10 minutes after the ignition is cycled to OFF. Opening either front door will cancel this feature. To change the Engine Off Power Delay status touch the 0 seconds, 45 seconds, 5 minutes or 10 minutes soft-key. Then touch the arrow back soft-key. • Headlight Off Delay When this feature is selected, the driver can choose to have the headlights remain on for 0, 30, 60, or 90 seconds when exiting the vehicle.
346 UNDERSTANDING YOUR INSTRUMENT PANEL • Speed Adjusted Volume Phone/Bluetooth® This feature increases or decreases volume relative to After pressing the “Phone/Bluetooth®” soft-key the folvehicle speed. To change the Speed Adjusted Volume lowing settings will be available. touch the Off, 1, 2 or 3 soft-key. Then touch the back • Paired Devices arrow soft-key. This feature shows which phones are paired to the • Music Info Cleanup Phone/Bluetooth® system.
UNDERSTANDING YOUR INSTRUMENT PANEL 347 your selection, touch the “Channel Skip” soft-key, select SRT Performance Features the channels you would like to skip followed by pressing To access the SRT Performance Features, touch the “SRT & the back arrow soft-key. More” soft-key then touch the “SRT Performance” soft-key. Press the UP or DOWN soft-key to cycle through the • Subscription Information features. Press the feature soft-key to select that feature.
348 UNDERSTANDING YOUR INSTRUMENT PANEL The Performance Features include the following: The following describes each feature and its operation: • Home Home • Timers When selected, this screen allows you to choose Sport Track mode. • Engine Values • Digital Gauge Displays • 0-60 mph (0-100 km/h) • This mode provides performance based suspension tuning with improved handling and acceleration through an electronic controlled dampening system.
UNDERSTANDING YOUR INSTRUMENT PANEL 349 • The feature will be “ready” when the vehicle speed is When a force greater than zero is measured, the display at 0 mph (0 km/h). will update the value as it climbs. As the G-Force falls, the peak forces will continue to display. • Soft-keys allow access to the current, best and last Gauges 1 times recorded.
350 UNDERSTANDING YOUR INSTRUMENT PANEL Gauges 2 • Oil Pressure When selected, this screen displays the following values: Shows the actual oil pressure. • Coolant Temperature • Battery Voltage Shows the actual coolant temperature within the range of Shows the actual battery voltage. the gauge. Engine • Oil Temperature When selected, this screen displays miles per hour (mph), Shows the actual oil temperature within the range of the horsepower (hp), torque (ft/lb), oil pressure (psi) and gauge.
UNDERSTANDING YOUR INSTRUMENT PANEL 351 SETTING THE ANALOG CLOCK iPod®/USB/MP3 CONTROL To set the analog clock at the top center of the instrument This feature allows an iPod® or external USB device to be panel, press and hold the button until the setting is plugged into the USB port. correct. iPod® control supports Mini, 4G, Photo, Nano, 5G iPod® and iPhone® devices. Some iPod® software versions may not fully support the iPod® control features. Please visit Apple’s website for software updates.
352 UNDERSTANDING YOUR INSTRUMENT PANEL HARMAN KARDON® Logic7® HIGH PERFORMANCE MULTICHANNEL SURROUND SOUND SYSTEM WITH DRIVER-SELECTABLE SURROUND (DSS) — IF EQUIPPED dynamic sound quality. The speakers are tuned for maximum efficiency and perfectly matched to the amplifier output stage ensuring state of the art multi-seat surround sound processing.
UNDERSTANDING YOUR INSTRUMENT PANEL 353 Pressing the center button will make the radio switch between the various modes available (AM/FM/SAT/ CD/HDD/AUX/VES, etc.). The left-hand control is a rocker-type switch with a pushbutton in the center. The function of the left-hand control is different depending on which mode you are in. The following describes the left-hand control operation in each mode.
354 UNDERSTANDING YOUR INSTRUMENT PANEL CD Player CD/DVD DISC MAINTENANCE Pressing the top of the switch once will go to the next To keep a CD/DVD in good condition, take the following track on the CD. Pressing the bottom of the switch once precautions: will go to the beginning of the current track, or to the 1. Handle the disc by its edge; avoid touching the beginning of the previous track if it is within eight surface. seconds after the current track begins to play. 2.
UNDERSTANDING YOUR INSTRUMENT PANEL 355 NOTE: If you experience difficulty in playing a particular disc, it may be damaged (e.g., scratched, reflective coating removed, a hair, moisture or dew on the disc) oversized, or have protection encoding. Try a known good disc before considering disc player service. RADIO OPERATION AND MOBILE PHONES Under certain conditions, the mobile phone being on in your vehicle can cause erratic or noisy performance from your radio.
356 UNDERSTANDING YOUR INSTRUMENT PANEL Soft-Keys Soft-keys are accessible on the Uconnect® system screen. Automatic Climate Controls — Hard-Keys Uconnect® 8.
UNDERSTANDING YOUR INSTRUMENT PANEL 357 Button Descriptions (Applies To Both Hard-Keys And 4. AUTO Operation Button Soft-Keys) Automatically controls the interior cabin temperature by 1. MAX A/C Button adjusting airflow distribution and amount. Performing Press and release to change the current setting, the this function will cause the ATC to switch between indicator illuminates when MAX A/C is ON. Performing manual mode and automatic modes.
358 UNDERSTANDING YOUR INSTRUMENT PANEL 6. Rear Defrost Button CAUTION! (Continued) Press and release this button to turn on the rear window defroster and the heated outside mirrors (if equipped). An indicator will illuminate when the rear window defroster is on. The rear window defroster automatically turns off after 10 minutes. • Do not use scrapers, sharp instruments, or abrasive window cleaners on the interior surface of the window. • Keep all objects a safe distance from the window. 7.
UNDERSTANDING YOUR INSTRUMENT PANEL 359 9. SYNC Soft-Key Press the Sync soft-key to toggle the Sync feature On/Off. The Sync indicator is illuminated when this feature is enabled. Sync is used to synchronize the passenger temperature setting with the driver temperature setting. Changing the passenger temperature setting while in Sync will automatically exit this feature. Use the small blower icon to reduce the blower setting and the large blower icon to increase the blower setting.
360 UNDERSTANDING YOUR INSTRUMENT PANEL is a shut off wheel located below the air vanes to shut off or adjust the amount of airflow from these outlets. • Mix Mode Air comes from the floor, defrost and side window demist outlets. This mode works best in cold or snowy conditions. Air comes from the instrument panel outlets and floor outlets. A slight amount of air is directed 12. Climate Control OFF Button through the defrost and side window demister outlets.
UNDERSTANDING YOUR INSTRUMENT PANEL 361 14. Driver Temperature Control Up Button NOTE: Provides the driver with independent temperature con- • If fog or mist appears on the windshield or side glass, select Defrost mode and increase blower speed. trol. Push the button for warmer temperature settings.
362 UNDERSTANDING YOUR INSTRUMENT PANEL In MAX A/C, the blower level and mode position can be adjusted to desired user settings. Pressing other settings will cause the MAX A/C operation to switch to the prior settings and the MAX A/C indicator will turn off. NOTE: In cold weather, use of Recirculation mode may lead to excessive window fogging. The recirculation feature may be unavailable (soft-key button greyed out).
UNDERSTANDING YOUR INSTRUMENT PANEL 363 3. When the system is set up for your comfort level, it is not necessary to change the settings. You will experience the greatest efficiency by simply allowing the system to function automatically. Manual Operation Override NOTE: • It is not necessary to move the temperature settings for cold or hot vehicles. The system automatically adjusts the temperature, mode, and blower speed to provide comfort as quickly as possible.
364 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Tips Vacation Storage Summer Operation Any time you store your vehicle or keep it out of service (i.e., vacation) for two weeks or more, run the air conditioning system at idle for about five minutes in the fresh air and high blower setting. This will ensure adequate system lubrication to minimize the possibility of compressor damage when the system is started again.
UNDERSTANDING YOUR INSTRUMENT PANEL 365 NOTE: A/C Air Filter • Recirculate without A/C should not be used for long The climate control system filters outside air containing dust, pollen and some odors. Strong odors cannot be periods, as fogging may occur. totally filtered out. Refer to “Maintenance Procedures” in • Automatic Temperature Controls (ATC) will automati- “Maintaining Your Vehicle” for filter replacement cally adjust the climate control settings to reduce or instructions.
STARTING AND OPERATING CONTENTS 䡵 STARTING PROCEDURES . . . . . . . . . . . . . . . .371 ▫ Key Ignition Park Interlock. . . . . . . . . . . . . . .378 ▫ Automatic Transmission . . . . . . . . . . . . . . . .371 ▫ Brake/Transmission Shift Interlock System . . .379 ▫ Keyless Enter-N-Go™ . . . . . . . . . . . . . . . . . .372 ▫ Five-Speed Automatic Transmission . . . . . . . .379 ▫ Normal Starting. . . . . . . . . . . . . . . . . . . . . . .372 䡵 AUTOSTICK® . . . . . . . . . . . . . . . . . . . . . . . .
368 STARTING AND OPERATING ▫ Traction . . . . . . . . . . . . . . . . . . . . . . . . . . . .393 ▫ Electronic Stability Control (ESC) . . . . . . . . . .404 䡵 DRIVING THROUGH WATER . . . . . . . . . . . . .394 ▫ Hill Start Assist (HSA) . . . . . . . . . . . . . . . . .407 ▫ Flowing/Rising Water . . . . . . . . . . . . . . . . . .394 ▫ Ready Alert Braking . . . . . . . . . . . . . . . . . . .409 ▫ Shallow Standing Water . . . . . . . . . . . . . . . . .394 ▫ Rain Brake Support . . . . . . . . . . . .
STARTING AND OPERATING 369 ▫ Tire Pressure . . . . . . . . . . . . . . . . . . . . . . . .423 ▫ Tire Rotation . . . . . . . . . . . . . . . . . . . . . . . . .436 ▫ Tire Inflation Pressures . . . . . . . . . . . . . . . . .424 䡵 TIRE PRESSURE MONITOR SYSTEM (TPMS) . .437 ▫ Tire Pressures For High Speed Operation . . . .426 ▫ Premium System . . . . . . . . . . . . . . . . . . . . . .440 ▫ Radial Ply Tires . . . . . . . . . . . . . . . . . . . . . .426 ▫ General Information . . . . . . . . . . . . . . .
370 STARTING AND OPERATING 䡵 ADDING FUEL . . . . . . . . . . . . . . . . . . . . . . . .449 ▫ Overloading . . . . . . . . . . . . . . . . . . . . . . . . .454 ▫ Emergency Fuel Filler Door Release. . . . . . . . .452 ▫ Loading . . . . . . . . . . . . . . . . . . . . . . . . . . . .455 䡵 VEHICLE LOADING . . . . . . . . . . . . . . . . . . . .453 䡵 TRAILER TOWING . . . . . . . . . . . . . . . . . . . . .455 ▫ Vehicle Certification Label . . . . . . . . . . . . . . .
STARTING AND OPERATING 371 STARTING PROCEDURES WARNING! (Continued) Before starting your vehicle, adjust your seat, adjust the inside and outside mirrors, fasten your seat belt, and if present, instruct all other occupants to buckle their seat belts. WARNING! • When leaving the vehicle, always remove the Key Fob from the ignition and lock your vehicle. • Never leave children alone in a vehicle, or with access to an unlocked vehicle.
372 STARTING AND OPERATING CAUTION! Damage to the transmission may occur if the following precautions are not observed: • Do not shift from REVERSE, PARK, or NEUTRAL into any forward gear when the engine is above idle speed. • Shift into PARK only after the vehicle has come to a complete stop. • Shift into or out of REVERSE only after the vehicle has come to a complete stop and the engine is at idle speed. • Before shifting into any gear, make sure your foot is firmly on the brake pedal.
STARTING AND OPERATING 373 3. The system takes over and attempts to start the vehicle. If the vehicle fails to start, the starter will disengage automatically after 10 seconds. 4. If you wish to stop the cranking of the engine prior to the engine starting, press the button again. NOTE: Normal starting of either a cold or a warm engine is obtained without pumping or pressing the accelerator pedal.
374 STARTING AND OPERATING ENGINE START/STOP Button Functions — With Driver’s Foot OFF The Brake Pedal (In PARK Or NEUTRAL Position) Extreme Cold Weather (Below –20°F Or −29°C) To ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (availThe ENGINE START/STOP button operates similar to an able from your authorized dealer) is recommended. ignition switch. It has three positions, OFF, ACC, RUN.
STARTING AND OPERATING 375 WARNING! (Continued) • Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transmission cannot be started this way. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle. • If the vehicle has a discharged battery, booster cables may be used to obtain a start from a booster battery or the battery in another vehicle.
376 STARTING AND OPERATING The engine block heater cord is routed under the hood on the driver side of the vehicle. It has a removable cap that The idle speed is controlled automatically and it will is located on the driver side of the Integrated Power decrease as the engine warms up. Module. ENGINE BLOCK HEATER — IF EQUIPPED After Starting The engine block heater warms the engine, and permits quicker starts in cold weather.
STARTING AND OPERATING 377 AUTOMATIC TRANSMISSION WARNING! (Continued) WARNING! • Unintended movement of a vehicle could injure those in or near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, always apply the parking brake, shift the transmission into PARK, turn the engine OFF, and remove the Key Fob. When the ignition is in the OFF position, the transmission is locked in PARK, securing the vehicle against unwanted movement.
378 STARTING AND OPERATING WARNING! (Continued) CAUTION! (Continued) • Children should be warned not to touch the parking brake, brake pedal or the shift lever. • Do not leave the Key Fob in or near the vehicle (or in a location accessible to children), and do not leave the ignition of a vehicle equipped with Keyless Enter-N-Go™ in the ACC or ON/RUN mode. A child could operate power windows, other controls, or move the vehicle.
STARTING AND OPERATING 379 the transmission in PARK. This system also locks the The electronically-controlled transmission provides a transmission in PARK whenever the ignition switch is in precise shift schedule. The transmission electronics are self-calibrating; therefore, the first few shifts on a new the OFF position. vehicle may be somewhat abrupt.
380 STARTING AND OPERATING Gear Ranges PARK (P) DO NOT race the engine when shifting from PARK or This range supplements the parking brake by locking the NEUTRAL into another gear range. transmission. The engine can be started in this range. Never attempt to use PARK while the vehicle is in NOTE: motion. Apply the parking brake when leaving the • After selecting any gear range, wait a moment to allow vehicle in this range. the selected gear to engage before accelerating.
STARTING AND OPERATING 381 WARNING! WARNING! (Continued) • Never use the PARK position as a substitute for the parking brake. Always apply the parking brake fully when parked to guard against vehicle movement and possible injury or damage. • Your vehicle could move and injure you and others if it is not completely in PARK. Check by trying to move the shift lever out of PARK with the brake pedal released. Make sure the transmission is in PARK before leaving the vehicle.
382 STARTING AND OPERATING WARNING! (Continued) WARNING! (Continued) • Unintended movement of a vehicle could injure those in or near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, always apply the parking brake, shift the transmission into PARK, turn the engine off, and remove the Key Fob. When the ignition is in the OFF position, the transmission is locked in PARK, securing the vehicle against unwanted movement.
STARTING AND OPERATING 383 CAUTION! • Before moving the shift lever out of PARK, you must turn the ignition switch from the LOCK/OFF position to the ON/RUN position, and also press the brake pedal. Otherwise, damage to the shift lever could result. • DO NOT race the engine when shifting from PARK or NEUTRAL into another gear range, as this can damage the drivetrain. • Look at the transmission gear position display and verify that it indicates the PARK position.
384 STARTING AND OPERATING WARNING! Do not coast in NEUTRAL and never turn off the ignition to coast down a hill. These are unsafe practices that limit your response to changing traffic or road conditions. You might lose control of the vehicle and have a collision. CAUTION! Towing the vehicle, coasting, or driving for any other reason with the transmission in NEUTRAL can cause severe transmission damage.
STARTING AND OPERATING 385 may be illuminated. Limp Home Mode allows the vehicle to be driven to an authorized dealer for service without This mode alters the transmission’s automatic shift damaging the transmission. schedule for sportier driving. Upshift speeds are increased to make full use of available engine power.
386 STARTING AND OPERATING NOTE: Even if the transmission can be reset, we recommend that you visit your authorized dealer at your earliest possible convenience. Your authorized dealer has diagnostic equipment to determine if the problem could recur. If the transmission cannot be reset, authorized dealer service is required.
STARTING AND OPERATING 387 1 — (–) Shift Paddle 2 — (+) Shift Paddle Operation When the shift lever is in the DRIVE position, the transmission will operate automatically, shifting between the five available gears. To engage AutoStick®, simply tap the shift lever to the right or left (+/-) while in the DRIVE position, or tap one of the steering wheelmounted shift paddles (+/-).
388 STARTING AND OPERATING • If AutoStick® is engaged while in SPORT mode, the • The system will ignore attempts to upshift at too low transmission will remain in the selected gear even of a vehicle speed. when maximum engine speed is reached. The trans• Avoid using speed control when AutoStick® is enmission will upshift only when commanded by the gaged. driver. Engine overspeed protection will be provided by fuel cut off at or near redline.
STARTING AND OPERATING 389 • Automatic (Auto) Mode — This is the default position when vehicle ignition is first turned on. This mode will This vehicle is equipped with an electronic controlled give a sporty, but comfortable ride. Within this mode, damping system. This system reduces body roll and pitch the suspension will adapt to the vehicle inputs, includin many driving situations including cornering, acceleraing vehicle speed, steering inputs, braking and acceltion and braking.
390 STARTING AND OPERATING When TRACK mode is enabled, a flag symbol When SPORT mode is enabled, a shock symbol will light up in the instrument cluster. Refer to will light up in the instrument cluster. Refer to “Instrument Cluster Description” in “Under“Instrument Cluster Description” in “Understanding Your Instrument Panel” for further standing Your Instrument Panel” for further information. information.
STARTING AND OPERATING 391 2. Press the “ESC OFF” button a second time to put the vehicle into Launch Control. The “ESC OFF” lamp will • Launch control should not be used on public roads. remain lit, and the cluster display will read “Launch Always check track conditions and the surrounding Control Enabled”. area. 3. Make sure the vehicle is not moving. • Launch Control is not available for the first 500 miles 4. Make sure the steering wheel is pointing straight. of vehicle life.
392 STARTING AND OPERATING 7. When conditions 3 through 6 have been met, the • The ESC system detects that the vehicle is no longer cluster EVIC display will read “Launch Ready Release moving in a straight line. ESC system continues in ESC full ON. Brake”. Release the brake and continue to hold wide open • The “ESC OFF” button is pressed to change the system throttle to launch. to another mode. One press puts the ESC system into ESC Full-On. 8. Keep the vehicle pointed straight.
STARTING AND OPERATING 393 when there is a difference in the surface traction under partial or complete loss of vehicle control and stopping ability. To reduce this possibility, the following precauthe rear (driving) wheels. tions should be observed: WARNING! Rapid acceleration on slippery surfaces is dangerous. Unequal traction can cause sudden pulling of the rear wheels. You could lose control of the vehicle and possibly have a collision.
394 STARTING AND OPERATING DRIVING THROUGH WATER Shallow Standing Water Driving through water more than a few inches/ Although your vehicle is capable of driving through centimeters deep will require extra caution to ensure shallow standing water, consider the following Cautions safety and prevent damage to your vehicle. and Warnings before doing so. Flowing/Rising Water WARNING! Do not drive on or across a road or path where water is flowing and/or rising (as in storm run-off).
STARTING AND OPERATING 395 CAUTION! CAUTION! (Continued) • Always check the depth of the standing water before driving through it. Never drive through standing water that is deeper than the bottom of the tire rims mounted on the vehicle. • Determine the condition of the road or the path that is under water and if there are any obstacles in the way before driving through the standing water. • Do not exceed 5 mph (8 km/h) when driving through standing water. This will minimize wave effects.
396 STARTING AND OPERATING POWER STEERING The standard power steering system will give you good vehicle response and increased ease of maneuverability in tight spaces. The system will provide mechanical steering capability if power assist is lost. If for some reason the power assist is interrupted, it will still be possible to steer your vehicle. Under these conditions, you will observe a substantial increase in steering effort, especially at very low vehicle speeds and during parking maneuvers.
STARTING AND OPERATING 397 CAUTION! Do not use chemical flushes in your power steering system as the chemicals can damage your power steering components. Such damage is not covered by the New Vehicle Limited Warranty. WARNING! Fluid level should be checked on a level surface and with the engine off to prevent injury from moving parts and to ensure accurate fluid level reading. Do not overfill. Use only manufacturer’s recommended power steering fluid.
398 STARTING AND OPERATING NOTE: • When the parking brake is applied and the transmission is placed in gear, the “Brake Warning Light” will flash. If vehicle speed is detected, a chime will sound to alert the driver. Fully release the parking brake before attempting to move the vehicle. • This light only shows that the parking brake is applied. It does not show the degree of brake application.
STARTING AND OPERATING 399 WARNING! WARNING! (Continued) • Never use the PARK position as a substitute for the parking brake. Always apply the parking brake fully when parked to guard against vehicle movement and possible injury or damage. • When leaving the vehicle, always remove the Key Fob from the ignition and lock your vehicle. • Never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons.
400 STARTING AND OPERATING CAUTION! If the “Brake Warning Light” remains on with the parking brake released, a brake system malfunction is indicated. Have the brake system serviced by an authorized dealer immediately. ANTI-LOCK BRAKE SYSTEM related motor noises. These noises are the system performing its self check cycle to ensure that the ABS is working properly. This self check occurs each time the vehicle is started and accelerated past 7 mph (11 km/h).
STARTING AND OPERATING 401 WARNING! WARNING! (Continued) • The ABS contains sophisticated electronic equipment that may be susceptible to interference caused by improperly installed or high output radio transmitting equipment. This interference can cause possible loss of anti-lock braking capability. Installation of such equipment should be performed by qualified professionals. • Pumping of the Anti-Lock Brakes will diminish their effectiveness and may lead to a collision.
402 STARTING AND OPERATING ELECTRONIC BRAKE CONTROL SYSTEM Your vehicle is equipped with an advanced electronic brake control system that include Anti-Lock Brake System (ABS), Traction Control System (TCS), Brake Assist System (BAS), and the Electronic Stability Control (ESC). All four of these systems work together to enhance vehicle stability and control in various driving conditions. Also, your vehicle may be equipped with Hill Start Assist (HSA), Ready Alert Braking, and Rain Brake Support.
STARTING AND OPERATING 403 A feature of the TCS system, Brake Lock Differential (BLD), controls the wheel spin across a driven axle. If one wheel on a driven axle is spinning faster than the other, the system will apply the brake of the spinning wheel. This will allow more engine torque to be applied to the wheel that is not spinning. This feature remains active even if TCS and ESC are in the “Partial Off” mode. Refer to “Electronic Stability Control (ESC)” in this section for more information.
404 STARTING AND OPERATING • Understeer - when the vehicle is turning less than appropriate for the steering wheel position. This system enhances directional control and stability of the vehicle under various driving conditions. The ESC WARNING! corrects for oversteering and understeering the vehicle by applying the brake of the appropriate wheel.
STARTING AND OPERATING 405 The “ESC Off” switch is located in the switch bank near the bottom center of the instrument panel. To enter the The ESC system has three available operating modes: “Partial Off” mode, momentarily press the “ESC Off” ESC On switch and the “ESC Activation/Malfunction Indicator This is the normal operating mode for the ESC. When- Light” will illuminate.
406 STARTING AND OPERATING WARNING! • When in “Partial Off” mode, the TCS functionality of ESC, (except for the limited slip feature described in the TCS section), has been disabled and the “ESC Off Indicator Light” will be illuminated. When in “Partial Off” mode, the engine power reduction feature of TCS is disabled, and the enhanced vehicle stability offered by the ESC system is reduced.
STARTING AND OPERATING 407 WARNING! Hill Start Assist (HSA) The HSA system is designed to assist the driver when starting a vehicle from a stop on a hill. HSA will maintain the level of brake pressure the driver applied for a short period of time after the driver takes their foot off of the brake pedal. If the driver does not apply the throttle during this short period of time, the system will release brake pressure and the vehicle will roll down the hill.
408 STARTING AND OPERATING • Gear selection matches vehicle uphill direction (i.e., Towing With HSA vehicle facing uphill is in forward gear; vehicle back- HSA will provide assistance when starting on a grade ing uphill is in REVERSE gear). when pulling a trailer. HSA will work in REVERSE and all forward gears when WARNING! the activation criteria have been met. The system will not activate if the vehicle is placed in NEUTRAL or PARK. • HSA is not a parking brake.
STARTING AND OPERATING 409 pressure. This brake pressure will not be noticed by the driver. The brake system uses this brake pressure to allow If you wish to turn off the HSA system, it can be done a fast brake response if the driver applies the brakes. using the Customer Programmable Features in the Electronic Vehicle Information Center (EVIC).
410 STARTING AND OPERATING ESC Activation/Malfunction Indicator Light And ESC OFF Indicator Light The “ESC Activation/Malfunction Indicator Light” (located in the instrument cluster) starts to flash as soon as the tires lose traction and the ESC system becomes active. The “ESC Activation/Malfunction Indicator Light” also flashes when TCS is active. If the “ESC Activation/ Malfunction Indicator Light” begins to flash during acceleration, ease up on the accelerator and apply as little throttle as possible.
STARTING AND OPERATING 411 • Each time the ignition is cycled to the ON/RUN Synchronizing ESC position, the ESC system will be ON even if it was cycled off previously. If the power supply is interrupted (battery disconnected or discharged), the “ESC • The ESC system will make buzzing or clicking sounds Activation/Malfunction Indicator Light” may when it is active. This is normal; the sounds will stop illuminate with the engine running.
412 STARTING AND OPERATING TIRE SAFETY INFORMATION NOTE: Tire Markings • P (Passenger) - Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designation. Example: P215/65R15 95H. • European-Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter ⬙P⬙ is absent from this tire size designation.
STARTING AND OPERATING 413 • Temporary spare tires are designed for temporary • High flotation tire sizing is based on U.S. design emergency use only. Temporary high pressure comstandards and it begins with the tire diameter molded pact spare tires have the letter “T” or “S” molded into into the sidewall. Example: 31x10.5 R15 LT. the sidewall preceding the size designation. Example: T145/80D18 103M. Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ⴖ...
414 STARTING AND OPERATING EXAMPLE: R = Construction code — ⬙R⬙ means radial construction — ⬙D⬙ means diagonal or bias construction 15 = Rim diameter in inches (in) Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions — The maximum speed corresponding to the speed symbol should only be achieved und
STARTING AND OPERATING 415 EXAMPLE: Load Identification: ⴖ....blank....
416 STARTING AND OPERATING EXAMPLE: DOT MA L9 ABCD 0301 DOT = Department of Transportation — This symbol certifies that the tire is in compliance with the U.S.
STARTING AND OPERATING 417 Tire Terminology And Definitions Term B-Pillar Cold Tire Inflation Pressure Maximum Inflation Pressure Recommended Cold Tire Inflation Pressure Tire Placard Definition The vehicle B-Pillar is the structural member of the body located behind the front door. Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or driven less than 1 mile (1.6 km) after sitting for a three hour period.
418 STARTING AND OPERATING Tire Loading And Tire Pressure Tire And Loading Information Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar or the rear edge of the driver’s side door.
STARTING AND OPERATING 419 Tire And Loading Information Placard This placard tells you important information about the: 1. Number of people that can be carried in the vehicle. 2. Total weight your vehicle can carry. 3. Tire size designed for your vehicle. 4. Cold tire inflation pressures for the front, rear, and spare tires.
420 STARTING AND OPERATING Loading To determine the maximum loading conditions of your vehicle, locate the statement “The combined weight of occupants and cargo should never exceed XXX lbs or XXX kg” on the Tire and Loading Information placard. The combined weight of occupants, cargo/luggage and trailer tongue weight (if applicable) should never exceed the weight referenced here. The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle.
STARTING AND OPERATING 421 4. The resulting figure equals the available amount of NOTE: cargo and luggage load capacity. For example, if • If your vehicle will be towing a trailer, load from your “XXX” amount equals 1,400 lbs (635 kg) and there will trailer will be transferred to your vehicle.
422 STARTING AND OPERATING
STARTING AND OPERATING 423 WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.
424 STARTING AND OPERATING WARNING! (Continued) • Unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • Always drive with each tire inflated to the recommended cold tire inflation pressure. Economy Ride Comfort And Vehicle Stability Proper tire inflation contributes to a comfortable ride. Over-inflation produces a jarring and uncomfortable ride.
STARTING AND OPERATING 425 (1.6 km) after a three hour period. The cold tire inflation pressure must not exceed the maximum inflation pressure • Check and adjust tire pressure with a good quality molded into the tire sidewall. pocket-type pressure gauge. Do not make a visual judgement when determining proper inflation.
426 STARTING AND OPERATING Tire Pressures For High Speed Operation Radial Ply Tires The manufacturer advocates driving at safe speeds and WARNING! within posted speed limits. Where speed limits or conditions are such that the vehicle can be driven at high Combining radial ply tires with other types of tires speeds, maintaining correct tire inflation pressure is very on your vehicle will cause your vehicle to handle important. Increased tire pressure and reduced vehicle poorly.
STARTING AND OPERATING 427 Consult an authorized tire dealer for tire repairs and Summer Or Three Season Tires — If Equipped additional information. Summer tires provide traction in both wet and dry Damaged Run Flat tires, or Run Flat tires that have conditions, and are not intended to be driven in snow or experienced a loss of pressure should be replaced imme- on ice.
428 STARTING AND OPERATING If you need snow tires, select tires equivalent in size and type to the original equipment tires. Use snow tires only in sets of four; failure to do so may adversely affect the safety and handling of your vehicle. Run Flat Tires — If Equipped Run Flat tires allow you the capability to drive 50 miles (80 km) at 50 mph (80 km/h) after a rapid loss of inflation pressure. This rapid loss of inflation is referred to as the Run Flat mode.
STARTING AND OPERATING 429 rotation for your vehicle. If your vehicle has this option, refer to an authorized tire dealer for the recommended NOTE: For vehicles equipped with TIREFIT instead of a tire rotation pattern. spare tire, please refer to “TIREFIT KIT” in “What To Do Compact Spare Tire — If Equipped In Emergencies” for further information.
430 STARTING AND OPERATING Do not install a wheel cover or attempt to mount a conventional tire on the compact spare wheel, since the wheel is designed specifically for the compact spare tire. Do not install more than one compact spare tire and wheel on the vehicle at any given time. WARNING! Compact spares are for temporary emergency use only. With these spares, do not drive more than 50 mph (80 km/h). Temporary use spares have limited tread life.
STARTING AND OPERATING 431 WARNING! Limited-use spares are for emergency use only. Installation of this limited-use spare tire affects vehicle handling. With this tire, do not drive more than the speed listed on the limit-use spare wheel. Keep inflated to the cold tire inflation pressures listed on your Tire and Loading Information Placard located on the driver’s side B-Pillar or the rear edge of the driver’s side door.
432 STARTING AND OPERATING tread wear indicators, the tire should be replaced. Refer to “Replacement Tires” in this section for further information. Life Of Tire The service life of a tire is dependent upon varying factors including, but not limited to: • Driving style • Tire pressure • Distance driven • Performance tires, tires with a speed rating of V or higher, and summer tires typically have a reduced tread life. Rotation of these tires per the vehicle maintenance schedule is highly recommended.
STARTING AND OPERATING 433 WARNING! Tires and the spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure. You could lose control and have a collision resulting in serious injury or death. Information placard or the Vehicle Certification Label for the size designation of your tire. The Load Index and Speed Symbol for your tire will be found on the original equipment tire sidewall.
434 STARTING AND OPERATING WARNING! WARNING! (Continued) • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle. This can cause unpredictable handling and stress to steering and suspension components. You could lose control and have a collision resulting in serious injury or death.
STARTING AND OPERATING 435 CAUTION! CAUTION! (Continued) To avoid damage to your vehicle or tires, observe the following precautions: • Because of restricted chain clearance between tires and other suspension components, it is important that only chains in good condition are used. Broken chains can cause serious damage. Stop the vehicle immediately if noise occurs that could indicate chain breakage. Remove the damaged parts of the chain before further use.
436 STARTING AND OPERATING Always use the lower suggested operating speed if both the chain manufacturer and vehicle manufacturer suggest a maximum speed. This notice applies to all chain traction devices, including link and cable (radial) chains. Refer to the “Maintenance Schedule” for the proper maintenance intervals. The reasons for any rapid or unusual wear should be corrected prior to rotation being performed.
STARTING AND OPERATING 437 TIRE PRESSURE MONITOR SYSTEM (TPMS) The Tire Pressure Monitor System (TPMS) will warn the driver of a low tire pressure based on the vehicle recommended cold placard pressure. Tire Rotation The tire pressure will vary with temperature by about 1 psi (7 kPa) for every 12°F (6.5°C). This means that when the outside temperature decreases, the tire pressure will decrease. Tire pressure should always be set based on cold inflation tire pressure.
438 STARTING AND OPERATING also increase as the vehicle is driven - this is normal and may need to be driven for up to 20 minutes above 15 mph there should be no adjustment for this increased pres- (24 km/h) in order for the TPMS to receive this information. sure. The TPMS will warn the driver of a low tire pressure if the tire pressure falls below the low-pressure warning limit for any reason, including low temperature effects and natural pressure loss through the tire.
STARTING AND OPERATING 439 CAUTION! • The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equipment that is not of the same size, type, and/or style. Aftermarket wheels can cause sensor damage. Using aftermarket tire sealants may cause the Tire Pressure Monitoring System (TPMS) sensor to become inoperable.
440 STARTING AND OPERATING • Seasonal temperature changes will affect tire pressure, • Various TPMS messages, which display in the Electronic Vehicle Information Center (EVIC) and the TPMS will monitor the actual tire pressure in the tire. • TPM Telltale Light Premium System The matching full size spare wheel and tire assembly (if The Tire Pressure Monitor System (TPMS) uses wireless equipped) has a TPM sensor.
STARTING AND OPERATING 441 each tire with the low tire pressure values flashing or Should this occur, you should stop as soon as possible changing color. An ⬙Inflate to XX⬙ message will also be and inflate the tires with a low pressure condition (those displayed. flashing or in a different color in the EVIC graphic) to the vehicle’s recommended cold placard pressure inflation value as shown in the ⬙Inflate to XX⬙ message.
442 STARTING AND OPERATING a minimum of five seconds and then display dashes (- -) in place of the pressure value to indicate which sensor is not being received. If the ignition switch is cycled, this sequence will repeat, providing the system fault still exists. If the system fault no longer exists, the TPM Telltale Light will no longer flash, and the ⬙SERVICE TPM SYSTEM⬙ message will no longer display, and a pressure value will display in place of the dashes.
STARTING AND OPERATING 443 4. Using tire chains on the vehicle. 5. Using wheels/tires not equipped with TPM sensors. limit, upon the next ignition switch cycle, a chime will sound and the TPM Telltale Light will turn ON. In addition, the EVIC will display a low pressure message and a graphic showing the low tire pressure value flashing or in a different color. An ⬙Inflate to XX⬙ message will also be displayed.
444 STARTING AND OPERATING 2. If you install the compact spare tire in place of a road will display a ⬙SERVICE TPM SYSTEM⬙ message for a tire that has a pressure below the low-pressure warnminimum of five seconds and then display dashes (- -) ing limit, upon the next ignition switch cycle, the TPM in place of the pressure value. Telltale Light will remain ON and a chime will sound. 5.
STARTING AND OPERATING 445 • This device must accept any interference received, Light spark knock at low engine speeds is not harmful to including interference that may cause undesired op- your engine. However, continued heavy spark knock at eration. high speeds can cause damage and immediate service is The TPM sensors are regulated under one of the follow- required. Poor quality gasoline can cause problems such as hard starting, stalling, and hesitations.
446 STARTING AND OPERATING Reformulated gasoline contain oxygenates and are specifically blended to reduce vehicle emissions and improve air quality. The manufacturer supports the use of reformulated gasoline. Properly blended reformulated gasoline will provide excellent performance and durability of engine and fuel system components.
STARTING AND OPERATING 447 If a Non-FFV vehicle is inadvertently fueled with E-85 MMT In Gasoline fuel, the engine will have some or all of these symptoms: Methylcyclopentadienyl Manganese Tricarbonyl (MMT) is a manganese-containing metallic additive that is • Operate in a lean mode. blended into some gasoline to increase octane. Gasoline • OBD II “Malfunction Indicator Light” on. blended with MMT provides no performance advantage beyond gasoline of the same octane number without • Poor engine performance.
448 STARTING AND OPERATING conditions and they would result in additional cost. Therefore, you should not have to add anything to the fuel. Fuel System Cautions CAUTION! Follow these guidelines to maintain your vehicle’s performance: • The use of leaded gas is prohibited by Federal law. Using leaded gasoline can impair engine performance and damage the emissions control system.
STARTING AND OPERATING 449 Carbon Monoxide Warnings WARNING! (Continued) WARNING! Carbon monoxide (CO) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • Do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas, which can kill. Never run the engine in a closed area, such as a garage, and never sit in a parked vehicle with the engine running for an extended period.
450 STARTING AND OPERATING Fuel Filler Door Release Switch 2. Open the fuel filler door. Fuel Filler Door NOTE: In certain cold conditions, ice may prevent the fuel door from opening. If this occurs, lightly push on the fuel door to break the ice buildup and re-release the fuel door using the inside release button. Do not pry on the door.
STARTING AND OPERATING 451 3. There is no fuel filler cap. A flapper door inside the pipe seals the system. 4. Insert the fuel nozzle fully into the filler pipe – the nozzle opens and holds the flapper door while refueling. NOTE: Only the correct size nozzle opens the latches allowing the flapper door to open. 5. Fill the vehicle with fuel – when the fuel nozzle “clicks” or shuts off the fuel tank is full. 5 6. Remove the fuel nozzle and close the fuel door.
452 STARTING AND OPERATING WARNING! 2. Remove the access cover (located on the left side inner trim panel). • Never have any smoking materials lit in or near the vehicle when the fuel door is open or the tank is being filled. • Never add fuel when the engine is running. This is in violation of most state and federal fire regulations and may cause the “Malfunction Indicator Light” to turn on. • A fire may result if fuel is pumped into a portable container that is inside of a vehicle. You could be burned.
STARTING AND OPERATING 453 Vehicle Certification Label Your vehicle has a Vehicle Certification Label affixed to the drivers side B-Pillar or the rear of the driver’s door.
454 STARTING AND OPERATING Gross Vehicle Weight Rating (GVWR) Overloading The GVWR is the total allowable weight of your vehicle. This includes driver, passengers, and cargo. The total load must be limited so that you do not exceed the GVWR. The load carrying components (axle, springs, tires, wheels, etc.) of your vehicle will provide satisfactory service as long as you do not exceed the GVWR and the front and rear GAWR.
STARTING AND OPERATING 455 Loading TRAILER TOWING To load your vehicle properly, first figure out its empty weight, axle-by-axle and side-by-side. Store heavier items down low and be sure you distribute their weight as evenly as possible. Stow all loose items securely before driving. If weighing the loaded vehicle shows that you have exceeded either GAWR, but the total load is within the specified GVWR, you must redistribute the weight.
WHAT TO DO IN EMERGENCIES CONTENTS 䡵 HAZARD WARNING FLASHERS . . . . . . . . . . .458 ▫ TIREFIT Usage Precautions. . . . . . . . . . . . . . .463 䡵 IF YOUR ENGINE OVERHEATS . . . . . . . . . . . .458 ▫ Sealing A Tire With TIREFIT . . . . . . . . . . . . . .466 䡵 WHEEL AND TIRE TORQUE 䡵 JUMP-STARTING PROCEDURES SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . .459 ▫ Preparations For Jump-Start . . . ▫ Torque Specifications . . . . . . . . . . . . . . . . . . .460 ▫ Jump-Starting Procedure . . . .
458 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHERS NOTE: With extended use the Hazard Warning flashers may wear down your battery. The Hazard Warning flasher switch is located in the center of the instrument panel between the center air IF YOUR ENGINE OVERHEATS outlets. In any of the following situations, you can reduce the Press the switch to turn on the Hazard Warning potential for overheating by taking the appropriate acflashers. When the switch is activated, all direc- tion.
WHAT TO DO IN EMERGENCIES 459 • You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high. This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system. CAUTION! Driving with a hot cooling system could damage your vehicle. If the temperature gauge reads 240°F (116°C) or greater pull over and stop the vehicle.
460 WHAT TO DO IN EMERGENCIES Torque Specifications Lug Nut/Bolt Torque **Lug Nut/ Bolt Size 130 Ft-Lbs (176 N·m) M14 x 1.50 Lug Nut/ Bolt Socket Size 22 mm **Use only Chrysler recommended lug nuts/bolts and clean or remove any dirt or oil before tightening. Inspect the wheel mounting surface prior to mounting the tire and remove any corrosion or loose particles. Wheel Mounting Surface Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been tightened twice.
WHAT TO DO IN EMERGENCIES 461 TIREFIT KIT — IF EQUIPPED Small punctures up to ¼” (6 mm) in the tire tread can be sealed with TIREFIT. Foreign objects (e.g., screws or nails) should not be removed from the tire. TIREFIT can be used in outside temperatures down to approximately -4°F (-20°C). This kit will provide a temporary tire seal, allowing you to drive your vehicle up to 100 miles (160 km) with a maximum speed of 55 mph (90 km/h).
462 WHAT TO DO IN EMERGENCIES TIREFIT Kit Components And Operation TIREFIT Location TIREFIT Components 1 2 3 4 — — — — Sealant Bottle Deflation Button Pressure Gauge Power Button 5 — Mode Select Knob 6 — Sealant Hose (Clear) 7 — Air Pump Hose (Black) 8 — Power Plug (located on bottom side of TIREFIT Kit)
WHAT TO DO IN EMERGENCIES 463 Using The Mode Select Knob And Hoses Your TIREFIT kit is equipped with the following symbols to indicate the air or sealant mode. Selecting Air Mode Using The Power Button Push and release the Power Button (4) once to turn On the TIREFIT kit. Push and release the Power Button (4) again to turn Off the TIREFIT kit. Push in the Mode Select Knob (5) and turn to this position for air pump operation only.
464 WHAT TO DO IN EMERGENCIES the vehicle or tire and wheel components. Once the sealant dries, it can easily be peeled off and properly discarded. • For optimum performance, make sure the valve stem on the wheel is free of debris before connecting the TIREFIT kit. • You can use the TIREFIT air pump to inflate bicycle tires. The kit also comes with two needles, located in the Accessory Storage Compartment (on the bottom of the air pump) for inflating sport balls, rafts, or similar inflatable items.
WHAT TO DO IN EMERGENCIES 465 WARNING! WARNING! (Continued) • Do not attempt to seal a tire on the side of the vehicle closest to traffic. Pull far enough off the road to avoid the danger of being hit when using the TIREFIT kit. • Do not use TIREFIT or drive the vehicle under the following circumstances: – If the puncture in the tire tread is approximately 1/4” (6 mm) or larger. – If the tire has any sidewall damage. – If the tire has any damage from driving with extremely low tire pressure.
466 WHAT TO DO IN EMERGENCIES WARNING! (Continued) • TIREFIT Sealant solution contains latex. In case of an allergic reaction or rash, consult a physician immediately. Keep TIREFIT out of reach of children. If swallowed, rinse mouth immediately with plenty of water and drink plenty of water. Do not induce vomiting! Consult a physician immediately. Sealing A Tire With TIREFIT (A) Whenever You Stop To Use TIREFIT: 1. Pull over to a safe location and turn on the vehicle’s Hazard Warning flashers.
WHAT TO DO IN EMERGENCIES 467 4. Remove the cap from the valve stem and then screw NOTE: Sealant may leak out through the puncture in the the fitting at the end of the Sealant Hose (6) onto the tire. valve stem. If the sealant (white fluid) does not flow within 0 – 10 5. Uncoil the Power Plug (8) and insert the plug into the seconds through the Sealant Hose (6): vehicle’s 12 Volt power outlet. 1. Press the Power Button (4) to turn Off the TIREFIT kit. NOTE: Do not remove foreign objects (e.g.
468 WHAT TO DO IN EMERGENCIES NOTE: If the Mode Select Knob (5) is on Air Mode and If the tire does not inflate to at least 26 psi (1.8 Bar) the pump is operating, air will dispense from the Air pressure within 15 minutes: Pump Hose (7) only, not the Sealant Hose (6). • The tire is too badly damaged. Do not attempt to drive the vehicle further. Call for assistance. If the sealant (white fluid) does flow through the Sealant Hose (6): NOTE: If the tire becomes over-inflated, press the Defla1.
WHAT TO DO IN EMERGENCIES 469 CAUTION! WARNING! • The metal end fitting from Power Plug (8) may get hot after use, so it should be handled carefully. • Failure to reinstall the cap on the fitting at the end of the Sealant Hose (6) can result in sealant contacting your skin, clothing, and the vehicle’s interior. It can also result in sealant contacting internal TIREFIT kit components which may cause permanent damage to the kit. TIREFIT is not a permanent flat tire repair.
470 WHAT TO DO IN EMERGENCIES 3. Uncoil the Air Pump Hose (7) (black in color) and 2. Disconnect the TIREFIT kit from the valve stem, screw the fitting at the end of hose (7) onto the valve reinstall the cap on the valve stem and unplug from 12 Volt outlet. stem. 4. Check the pressure in the tire by reading the Pressure 3. Place the TIREFIT kit in its proper storage area in the Gauge (3). vehicle. 4.
WHAT TO DO IN EMERGENCIES 471 (F) Sealant Bottle And Hose Replacement: 1. Uncoil the Sealant Hose (6) (clear in color). 6. Verify that the cap is installed on the fitting at the end of the Sealant Hose (6) and return the hose to its storage area (located on the bottom of the air pump). 2. Locate the round Sealant Bottle release button in the 7. Return the TIREFIT kit to its storage location in the recessed area under the sealant bottle. vehicle. 3. Press the Sealant Bottle release button.
472 WHAT TO DO IN EMERGENCIES CAUTION! Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or electrical system may occur. WARNING! Do not attempt jump-starting if the battery is frozen. It could rupture or explode and cause personal injury. Preparations For Jump-Start Remote Battery Post Locations The battery is stored under an access cover in the trunk.
WHAT TO DO IN EMERGENCIES 473 WARNING! • Take care to avoid the radiator cooling fan whenever the hood is raised. It can start anytime the ignition switch is ON. You can be injured by moving fan blades. • Remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact. You could be seriously injured. • Batteries contain sulfuric acid that can burn your skin or eyes and generate hydrogen gas which is flammable and explosive.
474 WHAT TO DO IN EMERGENCIES CAUTION! Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle. Connecting The Jumper Cables 1. Connect the positive (+) end of the jumper cable to the remote positive (+) post of the discharged vehicle. 2. Connect the opposite end of the positive (+) jumper cable to the positive (+) post of the booster battery. 4.
WHAT TO DO IN EMERGENCIES 475 6. Once the engine is started, remove the jumper cables in the reverse sequence: Disconnecting The Jumper Cables 1. Disconnect the negative (-) jumper cable from the remote negative (-) post of the vehicle with the discharged battery. 2. Disconnect the negative end (-) of the jumper cable from the negative (-) post of the booster battery. CAUTION! Accessories plugged into the vehicle power outlets draw power from the vehicle’s battery, even when not in use (i.e.
476 WHAT TO DO IN EMERGENCIES CAUTION! CAUTION! Racing the engine or spinning the wheels may lead to transmission overheating and failure. Allow the engine to idle with the transmission in NEUTRAL for at least one minute after every five rocking-motion cycles. This will minimize overheating and reduce the risk of clutch or transmission failure during prolonged efforts to free a stuck vehicle.
WHAT TO DO IN EMERGENCIES 477 WARNING! (Continued) explode and injure someone. Do not spin your vehicle’s wheels faster than 30 mph (48 km/h) or for longer than 30 seconds continuously without stopping when you are stuck and do not let anyone near a spinning wheel, no matter what the speed. 5. Insert a screwdriver or similar tool into the access port (in the left side of the storage bin), and push and hold the override release lever in.
478 WHAT TO DO IN EMERGENCIES TOWING A DISABLED VEHICLE This section describes procedures for towing a disabled vehicle using a commercial wrecker service. Towing Condition Flat Tow Wheel Lift Wheels OFF the Ground NONE Front Flatbed Rear ALL Proper towing or lifting equipment is required to prevent damage to your vehicle. Use only tow bars and other equipment designed for this purpose, following equipment manufacturer’s instructions. Use of safety chains is mandatory.
WHAT TO DO IN EMERGENCIES 479 CAUTION! • Do not use sling type equipment when towing. Damage to the fascia will occur. • When securing the vehicle to a flatbed truck, do not attach to the front or rear suspension components. Damage to your vehicle may result from improper towing. • Do not push or tow this vehicle with another vehicle as damage to the bumper fascia and transmission may result. • The ignition switch must be in the ON/RUN position, not in the OFF or ACC position.
480 WHAT TO DO IN EMERGENCIES If the transmission is not operable, or the vehicle must be towed faster than 30 mph (48 km/h) or farther than 15 miles (24 km), tow with the rear wheels OFF the ground (on a flatbed, or with the rear wheels raised using a wheel lift and the transmission in NEUTRAL). CAUTION! Towing this vehicle in violation of the above requirements can cause severe transmission damage. Damage from improper towing is not covered under the New Vehicle Limited Warranty.
MAINTAINING YOUR VEHICLE CONTENTS 䡵 ENGINE COMPARTMENT — 6.4L . . . . . . . . . .483 ▫ Maintenance-Free Battery . . . . . . . . . . . . . . .490 䡵 ONBOARD DIAGNOSTIC SYSTEM — OBD II . .484 ▫ Air Conditioner Maintenance . . . . . . . . . . . . .492 䡵 EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . .484 ▫ A/C Air Filter . . . . . . . . . . . . . . . . . . . . . . .493 䡵 REPLACEMENT PARTS . . . . . . . . . . . . . . . . . .486 䡵 DEALER SERVICE . . . . . . .
482 MAINTAINING YOUR VEHICLE ▫ Rear Axle . . . . . . . . . . . . . . . . . . . . . . . . . . .510 ▫ Low Beam And High Beam Headlamp . . . . . .529 ▫ Appearance Care And Protection From Corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . .511 ▫ Front Turn Signal Lamps . . . . . . . . . . . . . . . .531 䡵 FUSES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .517 ▫ Front Power Distribution Center (Fuses) . . . . .517 ▫ Rear Power Distribution Center (Fuses) . . . . .
MAINTAINING YOUR VEHICLE 483 ENGINE COMPARTMENT — 6.
484 MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
MAINTAINING YOUR VEHICLE 485 Indicator Light (MIL)” is functioning and is not on when 2. As soon as you cycle the ignition switch to the ON the engine is running, and that the OBD II system is position, you will see the MIL symbol come on as part ready for testing. of a normal bulb check. Normally, the OBD II system will be ready. The OBD II 3.
486 MAINTAINING YOUR VEHICLE you may need to do nothing more than drive your vehicle as you normally would in order for your OBD II system to update. A recheck with the above test routine may then indicate that the system is now ready. DEALER SERVICE Your authorized dealer has the qualified service personnel, special tools, and equipment to perform all service operations in an expert manner.
MAINTAINING YOUR VEHICLE 487 MAINTENANCE PROCEDURES CAUTION! (Continued) The pages that follow contain the required maintenance services determined by the engineers who designed your vehicle. Besides those maintenance items specified in the fixed “Maintenance Schedule”, there are other components which may require servicing or replacement in the future.
488 MAINTAINING YOUR VEHICLE regular intervals, such as every fuel stop. The best time to NOTE: Under no circumstances should oil change incheck the engine oil level is about five minutes after a tervals exceed 6,000 miles (10 000 km) or six months, whichever occurs first. fully warmed engine is shut off. Checking the oil while the vehicle is on level ground will improve the accuracy of the oil level readings. Maintain the oil level in the “SAFE” range. Adding 1.0 qt (1.
MAINTAINING YOUR VEHICLE 489 Engine Oil Viscosity engine oil. Engine oil is an engineered product and its performance may be impaired by supplemental additives. Use Pennzoil Ultra™ 0W-40 engine or equivalent MOPAR® oil meeting the Chrysler Material Standard Disposing Of Used Engine Oil And Oil Filters MS-12633 for use in all operating temperatures. Care should be taken in disposing of used engine oil and The engine oil filler cap also shows the recommended oil filters from your vehicle.
490 MAINTAINING YOUR VEHICLE quality filters should be used to assure most efficient Engine Air Cleaner Filter Selection service. MOPAR® engine oil filters are a high quality oil The quality of replacement engine air cleaner filters filter and are recommended. varies considerably. Only high quality filters should be used to assure most efficient service.
MAINTAINING YOUR VEHICLE 491 WARNING! Battery Location • Battery fluid is a corrosive acid solution and can burn or even blind you. Do not allow battery fluid to contact your eyes, skin, or clothing. Do not lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area immediately with large amounts of water. • Battery gas is flammable and explosive. Keep flame or sparks away from the battery.
492 MAINTAINING YOUR VEHICLE CAUTION! • It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked positive (+) and negative (-) and are identified on the battery case. Cable clamps should be tight on the terminal posts and free of corrosion.
MAINTAINING YOUR VEHICLE 493 CAUTION! Do not use chemical flushes in your air conditioning system as the chemicals can damage your air conditioning components. Such damage is not covered by the New Vehicle Limited Warranty. Refrigerant Recovery And Recycling R134a — If Equipped R-134a Air Conditioning Refrigerant is a hydrofluorocarbon (HFC) that is endorsed by the Environmental Protection Agency and is an ozone-saving product.
494 MAINTAINING YOUR VEHICLE 1. Remove the access door in the cowl screen by pressing the retaining clips. Filter Access Cover 3. Remove the used filter. Access Door 2. Unsnap both ends and lift the filter access cover. 4. Install the new filter with arrows pointing in the direction of airflow, which is toward the rear of the vehicle (text and arrows on the filter will indicate this).
MAINTAINING YOUR VEHICLE 495 Body Lubrication A/C Air Filter 5. Close the filter access cover. Locks and all body pivot points, including such items as seat tracks, door hinge pivot points and rollers, liftgate, tailgate, decklid, sliding doors and hood hinges, should be lubricated periodically with a lithium based grease, such as MOPAR® Spray White Lube to assure quiet, easy operation and to protect against rust and wear.
496 MAINTAINING YOUR VEHICLE Windshield Wiper Blades Clean the rubber edges of the wiper blades and the windshield periodically with a sponge or soft cloth and a mild nonabrasive cleaner. This will remove accumulations of salt or road film. Adding Washer Fluid The windshield washer fluid reservoir is located in the front of the engine compartment. Be sure to check the fluid level at regular intervals.
MAINTAINING YOUR VEHICLE 497 WARNING! Commercially available windshield washer solvents are flammable. They could ignite and burn you. Care must be exercised when filling or working around the washer solution. Exhaust System The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system.
498 MAINTAINING YOUR VEHICLE CAUTION! • The catalytic converter requires the use of unleaded fuel only. Leaded gasoline will destroy the effectiveness of the catalyst as an emissions control device and may seriously reduce engine performance and cause serious damage to the engine. • Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition.
MAINTAINING YOUR VEHICLE 499 To minimize the possibility of catalytic converter dam- Cooling System age: • Do not shut off the engine or interrupt the ignition, when the transmission is in gear and the vehicle is in motion. • Do not try to start the engine by pushing or towing the vehicle. • Do not idle the engine with any spark plug wires disconnected or removed, such as when diagnostic testing, or for prolonged periods during very rough idle or malfunctioning operating conditions.
500 MAINTAINING YOUR VEHICLE Coolant Checks With the engine at normal operating temperature (but not running), check the cooling system pressure cap for proper vacuum sealing by draining a small amount of engine coolant (antifreeze) from the radiator drain cock. If the cap is sealing properly, the engine coolant (antifreeze) will begin to drain from the coolant recovery bottle. DO NOT REMOVE THE COOLANT PRESSURE CAP WHEN THE COOLING SYSTEM IS HOT.
MAINTAINING YOUR VEHICLE 501 NOTE: Some vehicles require special tools to add coolant properly. Failure to fill these systems properly could lead to severe internal engine damage. If any coolant is needed to be added to the system please contact your local authorized dealer. Selection Of Coolant Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for further information.
502 MAINTAINING YOUR VEHICLE CAUTION! (Continued) • Do not use water alone or alcohol-based engine coolant (antifreeze) products. Do not use additional rust inhibitors or antirust products, as they may not be compatible with the radiator engine coolant and may plug the radiator. • This vehicle has not been designed for use with propylene glycol-based engine coolant (antifreeze). Use of propylene glycol-based engine coolant (antifreeze) is not recommended.
MAINTAINING YOUR VEHICLE 503 • Use only high purity water such as distilled or deion- • Mixing engine coolant (antifreeze) types is not recomized water when mixing the water/engine coolant mended and can result in cooling system damage. If HOAT and OAT coolant are mixed in an emergency, (antifreeze) solution.
504 MAINTAINING YOUR VEHICLE WARNING! • Do not open hot engine cooling system. Never add engine coolant (antifreeze) when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system. To prevent scalding or injury, do not remove the pressure cap while the system is hot or under pressure. • Do not use a pressure cap other than the one specified for your vehicle. Personal injury or engine damage may result.
MAINTAINING YOUR VEHICLE 505 When additional engine coolant (antifreeze) is needed to • Check the coolant freeze point in the radiator and in the coolant expansion bottle. If engine coolant (antimaintain the proper level, only OAT coolant that meets freeze) needs to be added, the contents of the coolant the requirements of Chrysler Material Standard MSexpansion bottle must also be protected against freez12106 should be added to the coolant bottle. Do not ing. overfill.
506 MAINTAINING YOUR VEHICLE • Do not change the thermostat for Summer or Winter operation. If replacement is ever necessary, install ONLY the correct type thermostat. Other designs may result in unsatisfactory engine coolant (antifreeze) performance, poor gas mileage, and increased emissions. WARNING! (Continued) high brake temperatures, excessive lining wear, and possible brake damage. You would not have your full braking capacity in an emergency.
MAINTAINING YOUR VEHICLE 507 Add enough fluid to bring the level up to the requirements described on the brake fluid reservoir. With disc brakes, fluid level can be expected to fall as the brake pads wear. However, low fluid level may be caused by a leak and a checkup may be needed. Use only manufacturer’s recommended brake fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for further information. WARNING! • Use only manufacturer’s recommended brake fluid.
508 MAINTAINING YOUR VEHICLE WARNING! (Continued) WARNING! (Continued) • To avoid contamination from foreign matter or moisture, use only new brake fluid or fluid that has been in a tightly closed container. Keep the master cylinder reservoir cap secured at all times. Brake fluid in a open container absorbs moisture from the air resulting in a lower boiling point. This may cause it to boil unexpectedly during hard or prolonged braking, resulting in sudden brake failure. This could result in a collision.
MAINTAINING YOUR VEHICLE 509 recommended fluid. No chemical flushes should be used Automatic Transmission Fluid (ATF) is an engineered in any transmission; only the approved lubricant should product and its performance may be impaired by supplemental additives. Therefore, do not add any fluid addibe used. tives to the transmission. The only exception to this policy is the use of special dyes for diagnosing fluid CAUTION! leaks.
510 MAINTAINING YOUR VEHICLE transmission filler tube is capped and no dipstick is In addition, change the fluid and filter if the fluid provided. Your authorized dealer can check your trans- becomes contaminated (with water, etc.), or if the transmission fluid level using a special service dipstick. mission is disassembled for any reason. If you notice fluid leakage or transmission malfunction, visit your authorized dealer immediately to have the transmission fluid level checked.
MAINTAINING YOUR VEHICLE 511 The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion Refer to the “Maintenance Schedule” for the proper resistance built into your vehicle. maintenance intervals. Appearance Care And Protection From Corrosion What Causes Corrosion? Change Axle Fluid Protection Of Body And Paint From Corrosion Vehicle body care requirements vary according to geographic locations and usage.
512 MAINTAINING YOUR VEHICLE Washing • Wash your vehicle regularly. Always wash your vehicle in the shade using MOPAR® Car Wash, or a mild car wash soap, and rinse the panels completely with clear water. CAUTION! • Do not use abrasive or strong cleaning materials such as steel wool or scouring powder that will scratch metal and painted surfaces. • Use of power washers exceeding 1,200 psi (8 274 kPa) can result in damage or removal of paint and decals.
MAINTAINING YOUR VEHICLE 513 • If your vehicle is damaged due to a collision or similar • To remove heavy soil and/or excessive brake dust, use MOPAR® Wheel Cleaner or equivalent or select a cause that destroys the paint and protective coating, non-abrasive, non-acidic cleaner. have your vehicle repaired as soon as possible. The cost of such repairs is considered the responsibility of CAUTION! the owner. • If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc.
514 MAINTAINING YOUR VEHICLE Stain Repel Fabric Cleaning Procedure — If Equipped Interior Care Use MOPAR® Total Clean to clean fabric upholstery and Stain Repel seats may be cleaned in the following man- carpeting. ner: Use MOPAR® Total Clean to clean vinyl upholstery. • Remove as much of the stain as possible by blotting MOPAR® Total Clean is specifically recommended for with a clean, dry towel. leather upholstery. • Blot any remaining stain with a clean, damp towel.
MAINTAINING YOUR VEHICLE 515 WARNING! Do not use volatile solvents for cleaning purposes. Many are potentially flammable, and if used in closed areas they may cause respiratory harm. CAUTION! To minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. To remove road dirt, wash with a mild soap solution followed by rinsing. Do not use abrasive cleaning components, solvents, steel wool or other aggressive material to clean the lenses.
516 MAINTAINING YOUR VEHICLE Replace the belts if they appear frayed or worn or if the The lenses in front of the instruments in this vehicle are buckles do not work properly. molded in clear plastic. When cleaning the lenses, care WARNING! must be taken to avoid scratching the plastic. 1. Clean with a wet soft rag. A mild soap solution may be A frayed or torn belt could rip apart in a collision and used, but do not use high alcohol content or abrasive leave you with no protection.
MAINTAINING YOUR VEHICLE 517 FUSES WARNING! (Continued) WARNING! • When replacing a blown fuse, always use an appropriate replacement fuse with the same amp rating as the original fuse. Never replace a fuse with another fuse of higher amp rating. Never replace a blown fuse with metal wires or any other material. Failure to use proper fuses may result in serious personal injury, fire and/or property damage.
518 MAINTAINING YOUR VEHICLE CAUTION! Front Power Distribution Center Cavity 1 2 Cartridge Fuse – 40 Amp Green • When installing the power distribution center cover, it is important to ensure the cover is properly positioned and fully latched. Failure to do so may allow water to get into the power distribution center and possibly result in an electrical system failure. • When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating.
MAINTAINING YOUR VEHICLE 519 Cavity 3 4 5 6 7 8 9 10 11 12 13 14 15 16 18 Cartridge Fuse 50 Amp Red 30 Amp Pink 40 Amp Green 25 Amp Natural – – – – – – – – – – 50 Amp Red Mini-Fuse – – – – – – 20 Amp Yellow 5 Amp Tan 20 Amp Yellow 10 Amp Red – – – – – Description Power Steering #1 Starter Anti-Lock Brakes Anti-Lock Brakes Fuse – Spare Fuse – Spare All-Wheel Drive Module – If Equipped Security Horns Air Conditioning Clutch Fuse – Spare Fuse – Spare Fuse – Spare Fuse – Spare Radiator Fan #2 7
520 MAINTAINING YOUR VEHICLE Cavity 19 20 21 22 23 24 28 29 30 31 32 33 34 35 36 Cartridge Fuse 50 Amp Red 30 Amp Pink 30 Amp Pink – – – – – – – – – – – – Mini-Fuse – – – – – – 25 Amp Natural 15 Amp Blue – 25 Amp Natural – – 25 Amp Natural 20 Amp Yellow 10 Amp Red Description Power Steering #2 Wiper Motor Headlamp Washers Fuse – Spare Fuse – Spare Fuse – Spare Fuel Pump Transmission Shifter Fuse – Spare Engine Module Fuse – Spare Fuse – Spare Powertrain #1 Powertrain #2 Anti-Lock Brake Module
MAINTAINING YOUR VEHICLE 521 Cavity 37 38 39 48 49 50 51 52 53 Cartridge Fuse – – – – – – – – – Mini-Fuse 10 Amp Red 10 Amp Red 10 Amp Red 10 Amp Red – – 20 Amp Yellow – – Description Engine Controller/Rad Fan Relays Airbag Module Power Steering Module/AC Clutch Relay AWD Module/Front Axle Disconnect Fuse – Spare Fuse – Spare Vacuum Pump Fuse – Spare Fuse – Spare 7
522 MAINTAINING YOUR VEHICLE Rear Power Distribution Center (Fuses) There is also a power distribution center located in the trunk under the spare tire access panel. This center contains fuses and relays. Rear Power Distribution Center CAUTION! • When installing the power distribution center cover, it is important to ensure the cover is properly positioned and fully latched. Failure to do so may allow water to get into the power distribution center and possibly result in an electrical system failure.
MAINTAINING YOUR VEHICLE 523 Cavity 2 3 4 5 6 7 8 9 10 11 12 Cartridge Fuse 60 Amp Yellow – 60 Amp Yellow 30 Amp Pink 40 Amp Green 40 Amp Green 30 Amp Pink 30 Amp Pink 30 Amp Pink 30 Amp Pink – Mini-Fuse – – – – – – – – – – 20 Amp Yellow 15 16 17 40 Amp Green – – – – – Description Front PDC Feed #1 Fuse – Spare Front PDC Feed #2 Sunroof Exterior Lighting #1 Exterior Lighting #2 Interior Lighting/Washer Pump Power Locks Driver Door Passenger Door Cigar Lighters, Instrument Panel & Power Outlet Console
524 MAINTAINING YOUR VEHICLE Cavity 18 19 20 21 22 23 24 25 26 Cartridge Fuse – – – – – – – – – 27 – 31 – 32 – Mini-Fuse 20 Amp Yellow – – – – 10 Amp Red 15 Amp Blue 10 Amp Red 25 Amp Natural 25 Amp Natural 25 Amp Natural 15 Amp Blue Description Active Dampening Module Fuse – Spare Fuse – Spare Fuse – Spare Fuse – Spare Fuel Door/Diagnostic Port Radio Screen Tire Pressure Monitor Transmission Amplifier Power Seats HVAC Module/Cluster
MAINTAINING YOUR VEHICLE 525 Cavity 33 34 35 36 37 38 40 41 42 43 44 45 46 47 48 Cartridge Fuse – – – – – – – – 30 Amp Pink – – – – – – Mini-Fuse 15 Amp Blue 10 Amp Red 10 Amp Red – 15 Amp Blue 20 Amp Yellow – – – 25 Amp Natural 10 Amp Red 15 Amp Blue 10 Amp Red 10 Amp Red 20 Amp Yellow Description Ignition Switch/Wireless Module Steering Column Module/Clock Battery Sensor Fuse – Spare Radio Power Outlet Inside Arm Rest Fuse – Spare Fuse – Spare Rear Defrost Rear Heated Seats/Steering Wheel Park Assist/
526 MAINTAINING YOUR VEHICLE Cavity 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 Cartridge Fuse – – – – – – – – – – – – – – – Mini-Fuse – – 20 Amp Yellow 10 Amp Red 10 Amp Red – – – – 10 Amp Red – – – – – Description Fuse – Spare Fuse – Spare Front Heated Seats Heated Cupholders/Rear Heated Seat Switches HVAC Module/In Car Temperature Sensor Fuse – Spare Fuse – Spare Fuse – Spare Fuse – Spare Airbag Module Fuse – Spare Fuse – Spare Fuse – Spare Fuse – Spare Fuse – Spare
MAINTAINING YOUR VEHICLE 527 Cavity 64 Cartridge Fuse – 65 66 67 68 69 70 – – – – – – Mini-Fuse 25 Amp Natural 10 Amp Red – 15 Amp Blue 15 Amp Blue – – VEHICLE STORAGE If you are leaving your vehicle dormant for more than 21 days, you may want to take these steps to protect your battery. • Disconnect the negative cable from the battery. • Anytime you store your vehicle, or keep it out of service (e.g.
528 MAINTAINING YOUR VEHICLE REPLACEMENT BULBS All of the interior bulbs are glass wedge base or glass cartridge types. Aluminum base bulbs are not approved and should not be used for replacement.
MAINTAINING YOUR VEHICLE 529 Daytime Running Lamp Front Fog Lamp – If Equipped Front Sidemarker Lamp Rear Tail/Stop/Turn Lamp Rear Sidemarker Lamp Backup Lamp Center High Mount Stop Lamp (CHMSL) License Rear Fog Lamp – If Equipped Bulb Number LED (Serviced at Authorized Dealer) H11 LED (Serviced at Authorized Dealer) LED (Serviced at Authorized Dealer) LED (Serviced at Authorized Dealer) W21W LED (Serviced at Authorized Dealer) W5W LED (Serviced at Authorized Dealer) BULB REPLACEMENT NOTE: Lens fogging c
530 MAINTAINING YOUR VEHICLE WARNING! A transient high voltage occurs at the bulb sockets of HID headlamps when the headlamp switch is turned ON. It may cause serious electrical shock or electrocution if not serviced properly. See your authorized dealer for service. 2. Reach behind the headlamp housing to access the headlamp (outboard) bulb cap. 3. Firmly grasp the cap and rotate it counterclockwise to unlock it. 4.
MAINTAINING YOUR VEHICLE 531 CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with an oily surface, clean the bulb with rubbing alcohol. Front Turn Signal Lamps 1. Open the hood. 4. Squeeze the two tabs on the side of the bulb socket and pull straight out from the lamp assembly. 5. Disconnect the bulb from the wiring connector and install the replacement bulb. 6.
532 MAINTAINING YOUR VEHICLE 4. Remove the three wing nuts from the back of the tail 11. Reinstall the bulb and socket assembly into the tail lamp assembly. lamp assembly, and then turn it clockwise. 5. Pull the tail lamp assembly away from the vehicle 12. Reinstall the tail lamp assembly, fasteners, electrical enough to access the electrical connector. connector, and trunk trim. 6. Push the electrical connector locking tab to the side. 13. Close the trunk. 7. Disconnect the electrical connector.
MAINTAINING YOUR VEHICLE 533 4. Reinstall the bulb and socket assembly. 5. Reattach the lamp to the rear fascia, and then install the screws.
534 MAINTAINING YOUR VEHICLE FLUID CAPACITIES Fuel (Approximate) Engine Oil With Filter 6.4 Liter Engine (SAE 0W-40, Synthetic API Certified) Cooling System * 6.4 Liter Engine (MOPAR Antifreeze/Engine Coolant (OAT coolant conforming to MS-12106) 10 Year/150,000 Mile Formula or equivalent) * Includes heater and coolant recovery bottle filled to MAX level. U.S. 19 Gallons Metric 72 Liters 7 Quarts 6.6 Liters 15.2 Quarts 14.
MAINTAINING YOUR VEHICLE 535 FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant Engine Oil Engine Oil Filter Spark Plugs Fuel Selection Fluid, Lubricant, or Genuine Part We recommend you use MOPAR® Antifreeze/Coolant 10 Year/150,000 Mile Formula OAT coolant conforming to MS-12106).
536 MAINTAINING YOUR VEHICLE Chassis Component Automatic Transmission Brake Master Cylinder Power Steering Reservoir Rear Axle Fluid, Lubricant, or Genuine Part Use only ATF+4® Automatic Transmission Fluid. Failure to use ATF+4® fluid may affect the function or performance of your transmission. We recommend MOPAR® ATF+4® fluid. We recommend you use MOPAR® DOT 3 brake fluid. If DOT 3 brake fluid is not available, then DOT 4 is acceptable.
M A I N T E N A ▫ Required Maintenance Intervals . . . . . . . . . . .539 N C E MAINTENANCE SCHEDULES CONTENTS 䡵 MAINTENANCE SCHEDULE . . . . . . . . . . . . .
M A I N T E N A N C E 538 MAINTENANCE SCHEDULES MAINTENANCE SCHEDULE Based on engine operation conditions, the oil change indicator message will illuminate. This means that service is required for your vehicle. Have your vehicle serviced as soon as possible, within the next 500 miles (805 km). The Scheduled Maintenance services listed in this manual must be done at the times or mileages specified to protect your vehicle warranty and ensure the best vehicle performance and reliability.
MAINTENANCE SCHEDULES 539 M Your authorized dealer will reset the oil change indicator • Check the fluid levels of the coolant reservoir, brake master cylinder, and power steering, and add as message after completing the scheduled oil change. If a needed. scheduled oil change is performed by someone other than your authorized dealer, the message can be reset by • Check all lights and other electrical items for correct referring to the steps described under “Electronic Vehicle operation.
M 540 MAINTENANCE SCHEDULES A I 6,000 Miles (10,000 km) or N T 6 Months Maintenance E Service Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate tires. C E S C H E D U L E S 8 Odometer Reading Repair Order # Signature, Authorized Service Center Date Dealer Code 12,000 Miles (20,000 km) or 12 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires.
MAINTENANCE SCHEDULES 541 M 18,000 Miles (30,000 km) or 18 Months Maintenance Service Schedule 24,000 Miles (40,000 km) or 24 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ Inspect the rear axle fluid. Odometer Reading Repair Order # Signature, Authorized Service Center Date Dealer Code ❏ Change the engine oil and engine oil filter. ❏ Rotate tires.
M 542 MAINTENANCE SCHEDULES A I 30,000 Miles (50,000 km) or N T 30 Months Maintenance E Service Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate tires. C ❏ Replace the engine air cleaner filter. E S C H E D U L E S 8 ❏ Adjust parking brake on vehicles equipped with four-wheel disc brakes.
MAINTENANCE SCHEDULES 543 M 42,000 Miles (70,000 km) or 42 Months Maintenance Service Schedule 48,000 Miles (80,000 km) or 48 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. Odometer Reading Repair Order # Signature, Authorized Service Center Date Dealer Code ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If you are using your vehicle in dusty or off-road conditions, inspect the engine air cleaner filter, and replace if necessary.
M 544 MAINTENANCE SCHEDULES A I 54,000 Miles (90,000 km) or N T 54 Months Maintenance E Service Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate tires. C ❏ Inspect the rear axle fluid. E S C H E D U L E S 8 Odometer Reading Repair Order # Signature, Authorized Service Center Date Dealer Code 60,000 Miles (100,000 km) or 60 Months Maintenance Service Schedule ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ Change the engine oil and engine oil filter. Rotate tires. Replace the engine air cleaner filter.
MAINTENANCE SCHEDULES 545 M 66,000 Miles (110,000 km) or 66 Months Maintenance Service Schedule 72,000 Miles (120,000 km) or 72 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. Odometer Reading Repair Order # Signature, Authorized Service Center Date Dealer Code ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If you are using your vehicle in dusty or off-road conditions, inspect the engine air cleaner filter, and replace if necessary.
M 546 MAINTENANCE SCHEDULES A I 78,000 Miles (130,000 km) or N T 78 Months Maintenance E Service Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate tires. C E S C H E D U L E S 8 Odometer Reading Repair Order # Signature, Authorized Service Center Date Dealer Code 84,000 Miles (140,000 km) or 84 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires.
MAINTENANCE SCHEDULES 547 M 90,000 Miles (150,000 km) or 90 Months Maintenance Service Schedule 96,000 Miles (160,000 km) or 96 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ Replace the engine air cleaner filter. ❏ Inspect and replace the PCV Valve if necessary. ❏ Inspect the rear axle fluid. ❏ Adjust parking brake on vehicles equipped with four-wheel disc brakes.
M 548 MAINTENANCE SCHEDULES A I 102,000 Miles (170,000 km) or N T 102 Months Maintenance E Service Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate tires. C E S C H E D U L E S 8 Odometer Reading Repair Order # Signature, Authorized Service Center Date Dealer Code 108,000 Miles (180,000 km) or 108 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires.
MAINTENANCE SCHEDULES 549 M 114,000 Miles (190,000 km) or 114 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. Odometer Reading Repair Order # Signature, Authorized Service Center Date Dealer Code 120,000 Miles (200,000 km) or 120 Months Maintenance Service Schedule ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ Change the engine oil and engine oil filter. Rotate tires. Replace the engine air cleaner filter. Replace the air conditioning filter.
M 550 MAINTENANCE SCHEDULES A I 126,000 Miles (210,000 km) or N T 126 Months Maintenance E Service Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate tires. C ❏ Inspect the rear axle fluid. E S C H E D U L E S 8 Odometer Reading Repair Order # Signature, Authorized Service Center Date Dealer Code 132,000 Miles (220,000 km) or 132 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires.
MAINTENANCE SCHEDULES 551 M 138,000 Miles (230,000 km) or 138 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. Odometer Reading Repair Order # Signature, Authorized Service Center Date Dealer Code 144,000 Miles (240,000 km) or 144 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires.
M 552 MAINTENANCE SCHEDULES A I 150,000 Miles (250,000 km) or N T 150 Months Maintenance E Service Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate tires. C ❏ Replace the engine air cleaner filter. E S C H E D U L E S 8 ❏ Adjust parking brake on vehicles equipped with four-wheel disc brakes. ❏ Flush and replace the engine coolant at 150,000 miles (240 000 km) or 120 months whichever comes first.
MAINTENANCE SCHEDULES 553 M WARNING! • You can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic. • Failure to properly inspect and maintain your vehicle could result in a component malfunction and effect vehicle handling and performance. This could cause an accident.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS 䡵 SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . .557 ▫ Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY). . . . . . . . . . . . . . . . . . .559 ▫ Prepare For The Appointment. . . . . . . . . . . . .557 ▫ Service Contract . . . . . . . . . . . . . . . . . . . . . .559 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . . .557 䡵 WARRANTY INFORMATION . . . . . . . . . . . . .
556 IF YOU NEED CONSUMER ASSISTANCE 䡵 DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES . . . . . . . . . . . . . . . . .563 ▫ Treadwear. . . . . . . . . . . . . . . . . . . . . . . . . . .563 ▫ Traction Grades . . . . . . . . . . . . . . . . . . . . . . .563 ▫ Temperature Grades. . . . . . . . . . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE 557 SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment Be Reasonable With Requests If you list a number of items and you must have your vehicle by the end of the day, discuss the situation with the service advisor and list the items in order of priority. At many authorized dealers, you may obtain a rental vehicle at a minimal daily charge. If you need a rental, it is advisable to make these arrangements when you call for an appointment.
558 IF YOU NEED CONSUMER ASSISTANCE facilities, factory-trained technicians, special tools, and • Authorized dealer name the latest information to ensure the vehicle is fixed • Vehicle Identification Number (VIN) correctly and in a timely manner. • Vehicle delivery date and mileage This is why you should always talk to an authorized dealer service manager first. Most matters can be re- Chrysler Group LLC Customer Center solved with this process. P.O.
IF YOU NEED CONSUMER ASSISTANCE 559 Mexico, D. F. Canadian residents with hearing difficulties that require assistance can use the special needs relay service offered by Bell Canada. For TTY teletypewriter users, dial 711 and for Voice callers, dial 1-800-855-0511 to connect with a Bell Relay Service operator.
560 IF YOU NEED CONSUMER ASSISTANCE The manufacturer will not stand behind any service contract that is not the manufacturer’s service contract. It is not responsible for any service contract other than the manufacturer’s service contract. If you purchased a service contract that is not a manufacturer’s service contract, and you require service after the manufacturer’s New Vehicle Limited Warranty expires, please refer to the contract documents, and contact the person listed in those documents.
IF YOU NEED CONSUMER ASSISTANCE 561 campaign. However, NHTSA cannot become involved in individual problems between you, your authorized MOPAR® fluids, lubricants, parts, and accessories are dealer, and the manufacturer. available from an authorized dealer. They are recommended for your vehicle in order to help keep the vehicle To contact NHTSA, you may either call the Auto Safety Hotline toll free at 1–888–327–4236 (TTY: 1–800–424– 9153), operating at its best. or go to http://www.safercar.
562 IF YOU NEED CONSUMER ASSISTANCE PUBLICATION ORDER FORMS To order the following manuals, you may use either the website or the phone numbers listed below. Visa, Mastercard, American Express, and Discover orders are accepted. If you prefer mailing your payment, please call for an order form. Diagnostic Procedure Manuals Diagnostic Procedure Manuals are filled with diagrams, charts and detailed illustrations.
IF YOU NEED CONSUMER ASSISTANCE 563 Call toll free at: Treadwear • 1–800–890–4038 (U.S.) The Treadwear grade is a comparative rating, based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half times as well on the government course as a tire graded 100.
564 IF YOU NEED CONSUMER ASSISTANCE WARNING! The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics. Temperature Grades The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel.
INDEX 10
566 INDEX About Your Brakes . . . . . . . . . . . . . . . . . . . . . . . .397 ABS (Anti-Lock Brake System) . . . . . . . . . . . . . . . .400 Adaptive Cruise Control (ACC) (Cruise Control) . . .221 Adding Engine Coolant (Antifreeze) . . . . . . . . . . . .502 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .449 Adding Washer Fluid . . . . . . . . . . . . . . . . . . . . . .496 Additives, Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . .447 Adjustable Pedals . . . . . . . . . .
INDEX 567 Automatic Oil Change Indicator . . . . . . . . . . . . . . .323 Automatic Temperature Control (ATC) . . . . . . . . . .362 Automatic Transmission . . . . . . . . . . . . . . . . . . . .379 Adding Fluid . . . . . . . . . . . . . . . . . . . . . . . . . .510 Fluid and Filter Changes . . . . . . . . . . . . . . . . . .510 Fluid Change . . . . . . . . . . . . . . . . . . . . . . . . . .510 Fluid Level Check . . . . . . . . . . . . . . . . . . . . . . .508 Fluid Type . . . . . . . . . . . . . . . . .
568 INDEX Break-In Recommendations, New Vehicle . . . . . . . . .99 Brightness, Interior Lights . . . . . . . . . . . . . . . . . . .204 Bulb Replacement . . . . . . . . . . . . . . . . . . . . . . . . .528 Bulbs, Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . .104 Camera, Rear . . . . . . . . . . . . Capacities, Fluid . . . . . . . . . . Caps, Filler Oil (Engine) . . . . . . . . . . . Power Steering . . . . . . . . . Radiator (Coolant Pressure) Carbon Monoxide Warning . .
INDEX 569 Compact Disc (CD) Maintenance . . . . Compact Spare Tire . . . . . . . . . . . . . . Computer, Trip/Travel. . . . . . . . . . . . Connector UCI . . . . . . . . . . . . . . . . . . . . . . . Universal Consumer Interface (UCI) Conserving Fuel . . . . . . . . . . . . . . . . Console, Floor . . . . . . . . . . . . . . . . . Contract, Service . . . . . . . . . . . . . . . . Coolant Pressure Cap (Radiator Cap) . Cooling System. . . . . . . . . . . . . . . . . Adding Coolant (Antifreeze) . . . . .
570 INDEX Electric Rear Window Defrost. . . . . . . . . . . . . . . . .297 Electric Remote Mirrors . . . . . . . . . . . . . . . . . . . . .115 Electronic Brake Control System . . . . . . . . . . . . . . .402 Anti-Lock Brake System . . . . . . . . . . . . . . . . . .402 Brake Assist System . . . . . . . . . . . . . . . . . . . . .403 Traction Control System . . . . . . . . . . . . . . . . . . .402 Electronic Power Distribution Center (Fuses) . . . . . .517 Electronic Speed Control (Cruise Control) . . . .
INDEX 571 Emergency, In Case of Freeing Vehicle When Stuck . . . . . . . . . . . . . . . .475 Hazard Warning Flasher . . . . . . . . . . . . . . . . . .458 Jump Starting . . . . . . . . . . . . . . . . . . . . . . . . . .471 Overheating . . . . . . . . . . . . . . . . . . . . . . . . . . .458 Emergency Trunk Release . . . . . . . . . . . . . . . . . . . .44 Emission Control System Maintenance . . . . . . . . . .484 Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .483 Air Cleaner . .
572 INDEX Exterior Lights . . . . . . . . . . . . . . . . . . . . . . . . . . .104 Filler Location Fuel . . . . . . Filters Air Cleaner . . . . . . . . . Air Conditioning . . . . . Engine Oil . . . . . . . . . . Engine Oil Disposal . . . Flashers Hazard Warning . . . . . . Turn Signal . . . . . . . . . Flash-To-Pass . . . . . . . . . . Flooded Engine Starting . . Floor Console . . . . . . . . . . Fluid, Brake . . . . . . . . . . . Fluid Capacities . . . . . . . . Fluid Leaks . . . . . . . . . . .
INDEX 573 Methanol . . . . Octane Rating . Requirements . Saver Mode . . Specifications . Tank Capacity . Fuel Optimizer . . Fuel Saver . . . . . Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
574 INDEX On With Wipers . . . . . . . . . . . . . . . . . . . . . Passing . . . . . . . . . . . . . . . . . . . . . . . . . . . Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . Time Delay . . . . . . . . . . . . . . . . . . . . . . . . . Washers . . . . . . . . . . . . . . . . . . . . . . . . . . . Headlight Washers . . . . . . . . . . . . . . . . . . . . . Head Restraints . . . . . . . . . . . . . . . . . . . . . . . Head Rests . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 575 Programming Additional Transmitters Remote Battery Replacement . . . . . . . Unlatch The Trunk . . . . . . . . . . . . . . Unlock The Doors . . . . . . . . . . . . . . Key-In Reminder . . . . . . . . . . . . . . . . . Keyless Enter-N-Go . . . . . . . . . . . . . . . Keyless Enter-N-Go™ Enter The Trunk . . . . . . . . . . . . . . . . Lock The Vehicle’s Doors . . . . . . . . . Passive Entry Programming . . . . . . . . Unlock From The Passenger Side . . . .
576 INDEX Lights On Reminder . . . . . . . . . . . . . . . . . Brake Warning . . . . . . . . . . . . . . . . . . . . . . . . .309 Low Fuel . . . . . . . . . . . . . . . . . . . . . . . . . Bulb Replacement . . . . . . . . . . . . . . . . . . . . . . .529 Malfunction Indicator (Check Engine) . . . . . Daytime Running . . . . . . . . . . . . . . . . . . . . . . .199 Map Reading . . . . . . . . . . . . . . . . . . . . . . Dimmer Switch, Headlight . . . . . . . . . . . . . . . . .
INDEX 577 Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 Methanol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .446 Automatic Door . . . . . . . . . . . . . . . . . . . . . . . . .32 Mini-Trip Computer . . . . . . . . . . . . . . . . . . . . . . .327 Auto Unlock . . . . . . . . . . . . . . . . . . . . . . . . . . .32 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112 Electric Powered . . . . . . . . . . . . . . . . . . . . . . . .
578 INDEX Occupant Restraints . . . . . . . . . . . . . . . . . . . . . . . .45 Occupant Restraints (Sedan) . . . . . . . . . . . . . . . . . .63 Octane Rating, Gasoline (Fuel) . . . . . . . . . . . . . . . .445 Odometer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .303 Oil Change Indicator . . . . . . . . . . . . . . . . . . . . . . .303 Oil Change Indicator, Reset . . . . . . . . . . . . . . . . . .303 Oil, Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .487 Capacity . . .
INDEX 579 Phone (Uconnect®) . . . . . . . . . . . . . . . . . . . . . . . .127 Placard, Tire and Loading Information . . . . . . . . . .419 Power Deck Lid Release . . . . . . . . . . . . . . . . . . . . . . . .43 Distribution Center (Fuses) . . . . . . . . . . . . . . . .522 Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .115 Outlet (Auxiliary Electrical Outlet) . . . . . . . . . . .282 Seats . . . . . . . . . . . . . .
580 INDEX Remote Control Starting System . . . . . . . . . . . . . . . . . . . . . . . . .26 Remote Keyless Entry (RKE) . . . . . . . . . . . . . . . . . .21 FCC General Information . . . . . . . . . . . . . . . . . .26 Lock The Doors . . . . . . . . . . . . . . . . . . . . . . . . .23 Panic Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 Programming Additional Key Fobs . . . . . . . . . . .18 Programming Additional Transmitters . . . . . . . . .18 Remote Battery Replacement . . . . . . . .
INDEX 581 Safety, Exhaust Gas . . . . . . . . . . . . . . . . . . . . . . . .101 Safety Information, Tire . . . . . . . . . . . . . . . . . . . . .412 Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100 Schedule, Maintenance . . . . . . . . . . . . . . . . . . . . .538 Seat Belt Maintenance . . . . . . . . . . . . . . . . . . . . . .516 Seat Belt Reminder . . . . . . . . . . . . . . . . . . . . . . . . .57 Seat Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
582 INDEX Service Contract . . . . . . . . . . . . . . . . . . . . . . . . . .559 Service Engine Soon Light (Malfunction Indicator) . . .306 Service Manuals . . . . . . . . . . . . . . . . . . . . . . . . . .562 Setting the Clock. . . . . . . . . . . . . . . . . . . . . . . . . .351 Shifting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .377 Automatic Transmission . . . . . . . . . . . . . . . . . .377 Shoulder Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 583 Storing Your Vehicle . . . . . . . . . . . . . . . . . . . . . . .527 Stuck, Freeing . . . . . . . . . . . . . . . . . . . . . . . . . . . .475 Sunglasses Storage . . . . . . . . . . . . . . . . . . . . . . . .264 Sun Roof . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .274 Supplemental Restraint System - Airbag . . . . . . . . . .59 Synthetic Engine Oil . . . . . . . . . . . . . . . . . . . . . . .489 System, Remote Starting . . . . . . . . . . . . . . . . . . . . .26 Tachometer. .
584 INDEX Tire Safety Information . . . . . . . . . . . . . . . . . . . . .412 To Open Hood . . . . . . . . . . . . . . . . . . . . . . . . . . .193 Towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .455 Behind a Motorhome . . . . . . . . . . . . . . . . . . . . .455 Recreational . . . . . . . . . . . . . . . . . . . . . . . . . . .455 Towing Vehicle Behind a Motorhome . . . . . . . . . . .455 Traction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .392 Traction Control .
INDEX 585 Passive Entry Programming . . . . . . . . . . . . . . . . .34 Uconnect® Settings . . . . . . . . . . . . . . . . . . . . . .341 Uconnect® Voice Command. . . . . . . . . . . . . . . . . .165 Uniform Tire Quality Grades . . . . . . . . . . . . . . . . .563 Universal Consumer Interface (UCI) Connector . . . .351 Unleaded Gasoline . . . . . . . . . . . . . . . . . . . . . . . .445 Untwisting Procedure, Seat Belt . . . . . . . . . . . . . . . .54 Vanity Mirrors . . . . . . . . . . . . . . . . . . . .
586 INDEX Windshield Defroster. . . . Windshield Washers . . . . Fluid . . . . . . . . . . . . . Windshield Wiper Blades . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102 .207 .496 .496 Windshield Wipers . . . . . Wiper Blade Replacement Wipers, Intermittent . . . . Wipers, Rain Sensitive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained personnel. The following must be observed during installation. The positive power connection should be made directly to the battery and fused as close to the battery as possible.
2014 300 SRT 2014 OWNER’S MANUAL Chrysler Group LLC 14C482-126-AD Fourth Edition Printed in U.S.A.
