2014 200 2014 OWNER’S MANUAL Chrysler Group LLC 14C41-126-AC Third Edition Printed in U.S.A.
VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name Chrysler Group LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefore. Drunken driving is one of the most frequent causes of accidents. This manual illustrates and describes the operation of features and equipment that are either standard or optional on this vehicle.
SECTION TABLE OF CONTENTS PAGE 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101 3 4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION CONTENTS 䡵 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . .4 䡵 VEHICLE IDENTIFICATION NUMBER . . . . . . . .6 䡵 HOW TO USE THIS MANUAL . . . . . . . . . . . . . .4 䡵 VEHICLE MODIFICATIONS/ALTERATIONS . . . .7 䡵 WARNINGS AND CAUTIONS . . . . . . . . . . . . . .
4 INTRODUCTION When it comes to service, remember that your authorized dealer knows your vehicle best, has factory-trained techCongratulations on selecting your new Chrysler Group nicians and genuine parts, and cares about your satisfacLLC vehicle. Be assured that it represents precision tion. workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles.
INTRODUCTION 5 1
6 INTRODUCTION WARNINGS AND CAUTIONS This Owners Manual contains WARNINGS against operating procedures that could result in a collision or bodily injury. It also contains CAUTIONS against procedures that could result in damage to your vehicle. If you do not read this entire Owners Manual, you may miss important information. Observe all Warnings and Cautions.
INTRODUCTION 7 VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death. Stamped VIN Location NOTE: It is illegal to remove or alter the VIN.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS 䡵 A WORD ABOUT YOUR KEYS . . . . . . . . . . . . .12 ▫ To Arm The System . . . . . . . . . . . . . . . . . . . .19 ▫ Ignition Key Removal . . . . . . . . . . . . . . . . . . .12 ▫ To Disarm The System . . . . . . . . . . . . . . . . . . .20 ▫ Key-In-Ignition Reminder . . . . . . . . . . . . . . . .15 ▫ Tamper Alert . . . . . . . . . . . . . . . . . . . . . . . . .21 ▫ Locking The Doors With The Key . . . . . . . . . . .
10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Programming Additional Transmitters. . . . . . . .26 ▫ Transmitter Battery Replacement . . . . . . . . . . .26 ▫ General Information . . . . . . . . . . . . . . . . . . . .27 䡵 REMOTE START SYSTEM — IF EQUIPPED . . . .28 ▫ How To Use Remote Start . . . . . . . . . . . . . . . .28 䡵 DOOR LOCKS . . . . . . . . . . . . . . . . . . . . . . . . .31 ▫ Manual Door Locks . . . . . . . . . . . . . . . . . . . . .31 ▫ Power Door Locks . . . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 ▫ Automatic Locking Retractor Mode (ALR) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . .52 ▫ Energy Management Feature . . . . . . . . . . . . . .53 ▫ Seat Belt Pretensioners . . . . . . . . . . . . . . . . . .53 ▫ Supplemental Active Head Restraints (AHR) . . .53 ▫ Air Bag Deployment Sensors And Controls . . . .65 ▫ Event Data Recorder (EDR) . . . . . . . . . . . . . . .72 ▫ Child Restraints . . . . . . . . . . . . . . . . . . . . . . .
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS The authorized dealer that sold you your vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys from your authorized dealer. Ask your authorized dealer for these numbers and keep them in a safe place. You can insert the double-sided keys into the locks with either side up. Vehicle Key Ignition Key Removal Automatic Transaxle Place the shift lever in PARK.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 NOTE: • If you try to remove the key before you place the shift lever in PARK, the key may become trapped temporarily in the ignition switch lock cylinder. If this occurs, rotate the key to the right slightly, then remove the key as described. If a malfunction occurs, the system will trap the key in the ignition switch lock cylinder to warn you that this safety feature is inoperable.
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • For vehicles equipped with the Electronic Vehicle Information Center (EVIC), the power window switches, radio, hands–free system (if equipped), and power outlets will remain active for up to 10 minutes after the ignition switch is turned to the LOCK position. Opening either front door will cancel this feature. The time for this feature is programmable.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 key forward. For door lock lubrication, see “Maintenance Procedures” in “Maintaining Your Vehicle” of this Opening the driver’s door when the key is in the ignition manual. sounds a signal to remind you to remove the key. Key-In-Ignition Reminder NOTE: SENTRY KEY® • The Key-In-Ignition reminder only sounds when the The Sentry Key® Immobilizer System prevents unauignition key is placed in the LOCK or ACC position.
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: A key which has not been programmed is also considered an invalid key even if it is cut to fit the ignition switch lock cylinder for that vehicle. During normal operation, after turning on the ignition switch, the Vehicle Security Light will turn on for three seconds for a bulb check. If the light remains on after the bulb check, it indicates that there is a problem with the electronics.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 CAUTION! Always remove the Sentry Key® from the vehicle and lock all doors when leaving the vehicle unattended. Customer Key Programming You can program new keys to the system if you have two valid Sentry Keys® by performing the following procedure: 1. Cut the additional Sentry Key® Transponder blank(s) At the time of purchase, the original owner is provided to match the ignition switch lock cylinder key code.
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Insert a blank Sentry Key® into the ignition switch. Turn the ignition switch to the ON/RUN position within 60 seconds. After 10 seconds, a single chime will sound. In addition, the Vehicle Security Light will stop flashing. To indicate that programming is complete, the indicator light will turn on again for three seconds and then turn off.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 horn after three minutes, turn off all of the visual signals after 15 minutes, and then the Vehicle Security Alarm will The Vehicle Security Alarm monitors the doors and trunk rearm itself. for unauthorized entry and ignition switch for unauthorized operation. While the Vehicle Security Alarm is To Arm The System armed, interior switches for door locks and decklid 1. Remove the keys from the ignition switch and get out release are disabled. of the vehicle.
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE or the power door locks are unlocked in any manner, NOTE: the Vehicle Security Alarm will automatically disarm. • The driver’s door key cylinder and the trunk button on the RKE transmitter cannot arm or disarm the Vehicle NOTE: Security Alarm. • During the 16-second arming period, if a door is opened or the ignition switch is turned to ON/RUN, • The Vehicle Security Alarm remains armed during trunk entry.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 If the Vehicle Security Alarm is armed and the battery becomes disconnected the Vehicle Security Alarm will remain armed when the battery is reconnected. The exterior lights will flash, and the horn will sound. If this occurs, disarm the Vehicle Security Alarm. This feature also turns on the approach lighting in the outside mirrors (if equipped). Refer to “Mirrors” in “Understanding The Features Of Your Vehicle” for further information.
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE REMOTE KEYLESS ENTRY (RKE) — IF EQUIPPED This system allows you to lock or unlock the doors, open the trunk, or activate the Panic Alarm from distances approximately 66 ft (20 m) using a Remote Keyless Entry (RKE) transmitter. The RKE transmitter does not need to be pointed at the vehicle to activate the system. NOTE: • The line of transmission must not be blocked with metal objects.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 Remote Key Unlock, Driver Door/All Doors First Press This feature lets you program the system to unlock either the driver’s door or all doors on the first press of the UNLOCK button on the RKE transmitter. To change the current setting, proceed as follows: 2. Release both buttons at the same time. 3.
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Flash Lights With Lock 2. Release both buttons at the same time. The feature will cause the turn signal lights to flash when 3. Test the feature while outside of the vehicle by pressthe doors are locked or unlocked with the RKE transmiting the LOCK/UNLOCK buttons on the RKE transter. This feature can be turned on or turned off. To change mitter with the ignition in the LOCK position and the the current setting, proceed as follows: key removed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 equipped with EVIC. For details, refer to “Electronic • For vehicles not equipped with the EVIC, perform the following steps: Vehicle Information Center (EVIC)/Personal Settings (Customer-Programmable Features)” in “Understanding 1. Press the LOCK button on a programmed RKE transYour Instrument Panel” for further information. mitter for at least 4 seconds, but not longer than 10 seconds.
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: If there is no key in the ignition switch, pressing the LOCK button on the RKE transmitter while you are in the vehicle will activate the Vehicle Security Alarm. Opening a door with the alarm activated will cause the alarm to sound. Press the UNLOCK button to deactivate the Vehicle Security Alarm.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 1. With the RKE transmitter buttons facing down, use a 2. Remove and replace the battery. Avoid touching the flat blade screwdriver to pry the two halves of the RKE new battery with your fingers. Skin oils may cause transmitter apart. Make sure not to damage the seal battery deterioration. If you touch a battery, clean it during removal. with rubbing alcohol. 3. To assemble the RKE transmitter case, snap the two halves together.
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Changes or modifications not expressly approved NOTE: The vehicle must be equipped with an automatic by the party responsible for compliance could void the transmission to be equipped with Remote Start. user’s authority to operate the equipment. How To Use Remote Start If your RKE transmitter fails to operate from a normal All of the following conditions must be met before the distance, check for these two conditions: engine will remote start: 1.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 • System not disabled from previous remote start event Remote Start Abort Message On Electronic Vehicle Information Center (EVIC) — If Equipped • Vehicle Security Alarm not active The following messages will display in the EVIC if the vehicle fails to remote start or exits remote start premaWARNING! turely: • Do not start or run an engine in a closed garage or confined area.
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Enter Remote Start Mode Press and release the REMOTE START button on the RKE transmitter twice within five seconds. The vehicle doors will lock, the parking lights will flash and the horn will chirp twice (if programmed). Then, the engine will start and the vehicle will remain in the Remote Start mode for a 15-minute cycle. NOTE: the ignition switch must be cycled to the ON/RUN position before you can repeat the start sequence for a third cycle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 To Exit Remote Start Mode Without Driving The Vehicle DOOR LOCKS Manual Door Locks Press and release the REMOTE START button one time or To lock each door, push the door lock knob on each door allow the engine to run for the entire 15 minute cycle. trim panel downward. To unlock each door, pull the NOTE: To avoid unintentional shut downs, the system inside door handle.
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! (Continued) • For personal security and safety in the event of an collision, lock the vehicle doors as you drive as well as when you park and leave the vehicle. • Before exiting a vehicle, always apply the parking brake, shift the transmission into PARK, and remove the Key Fob from the ignition. When leaving the vehicle, always lock your vehicle. • Never leave children alone in a vehicle, or with access to an unlocked vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 auto door lock feature can be enabled or disabled by your authorized dealer. Please see your authorized dealer for service. Auto Unlock On Exit The doors will unlock automatically on vehicles with power door locks if: 1. The Automatic Unlock Doors On Exit feature is enabled. 2. The transmission was in gear and the vehicle speed returned to 0 mph (0 km/h). Power Door Lock Switch Automatic Door Locks — If Equipped 3. The transmission is in NEUTRAL or PARK. 4.
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. A single chime will indicate the completion of the programming. The Automatic Unlock Doors On Exit feature can be enabled or disabled as follows: 5. Repeat these steps if you want to return this feature to its previous setting.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 2 Child-Protection Door Lock Location The Child-Protection Door Locks are located inside the rear edge of the door. Insert the tip of the ignition key or similar flat-bladed object into the lock and rotate clockwise approximately one-quarter turn to the lock position or counter clockwise to the unlock position (as indicated by the stamped icons). Child Lock Control WARNING! Avoid trapping anyone in a vehicle in a collision.
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: For emergency exit with the system engaged, pull the lock knob up (UNLOCKED position), roll down the window, and open the door with the outside door handle. POWER WINDOWS Power Window Switches The control on the driver’s door has up/down switches that give you fingertip control of all four power windows.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 WARNING! Never leave children unattended in a vehicle, and do not let children play with power windows. Do not leave the Key Fob in or near the vehicle, or in a location accessible to children. Occupants, particularly unattended children, can become entrapped by the windows while operating the power window switches. Such entrapment may result in serious injury or death.
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Auto Window Up With Anti-Pinch Protection — If Equipped NOTE: • If the window runs into any obstacle during autoclosure, anti-pinch protection will reverse the window direction and then go back down. Remove the obstacle and use the window switch again to close the window. To cancel the Auto Up movement, operate the switch either in the up or down direction and release the switch.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 Reset Auto Up Should the Auto Up feature stop working, the window probably needs to be reset. To reactivate the Auto Up feature, pull the window switch up to close the window completely and continue to hold the switch up for an additional two seconds after the window is closed. 2 Window Lockout Switch The window lockout switch on the driver’s door allows you to disable the window control on the other doors.
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE open or partially open positions. This is a normal occurrence and can be minimized. If the buffeting occurs with the rear windows open, then open the front and rear windows together to minimize the buffeting. If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting. TRUNK LOCK AND RELEASE Use the Remote Keyless Entry (RKE) transmitter to open the trunk from outside the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 TRUNK SAFETY WARNING WARNING! 2 Do not allow children to have access to the trunk, either by climbing into the trunk from outside, or through the inside of the vehicle. Always close the trunk lid when your vehicle is unattended. Once in the trunk, young children may not be able to escape, even if they entered through the rear seat. If trapped in the trunk, children can die from suffocation or heat stroke.
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Advanced Front Air Bags for driver and front passenger seat belt webbing into position by extending the belt all the way out and then adjusting the belt to the desired length to restrain a child seat or secure a large item in a seat. • Supplemental Active Head Restraints (AHR) located on top of the front seats (integrated into the head restraint) — if equipped Please pay close attention to the information in this section.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 Here are some simple steps you can take to minimize the ride properly buckled up in the rear seat. Never allow risk of harm from a deploying air bag: children to slide the shoulder belt behind them or under their arm. If a child from 2 to 12 years old (not in a rear 1. Children 12 years old and under should always ride facing child seat) must ride in the front passenger seat, buckled up in a rear seat.
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 5. If the air bag system in this vehicle needs to be modified to accommodate a disabled person, contact the Customer Center. Phone numbers are provided under “If You Need Assistance”. WARNING! • Relying on the air bags alone could lead to more severe injuries in a collision. The air bags work with your seat belt to restrain you properly. In some collisions, the air bags won’t deploy at all. Always wear your seat belts even though you have air bags.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 Buckle up even though you are an excellent driver, even reduce your risk of striking the inside of the vehicle or on short trips. Someone on the road may be a poor driver being thrown out. and cause a collision that includes you. This can happen far away from home or on your own street. WARNING! Research has shown that seat belts save lives, and they can reduce the seriousness of injuries in a collision.
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • Wearing your belt in the wrong place could make your injuries in a collision much worse. You might suffer internal injuries, or you could even slide out of part of the belt. Follow these instructions to wear your seat belt safely and to keep your passengers safe, too. • Two people should never be belted into a single seat belt. People belted together can crash into one another in a collision, hurting one another badly.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” WARNING! • A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you properly.
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A belt that is worn under your arm is dangerous. Your body could strike the inside surfaces of the vehicle in a collision, increasing head and neck injury. A belt worn under the arm can cause internal injuries. Ribs aren’t as strong as shoulder bones. Wear the belt over your shoulder so that your strongest bones will take the force in a collision. • A shoulder belt placed behind you will not protect you from injury during a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 WARNING! • A lap belt worn too high can increase the risk of injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap part of your seat belt as low as possible and keep it snug. • A twisted belt may not protect you properly. In a collision, it could even cut into you. Be sure the belt is straight.
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE your neck. Push anchorage button to release the anchorage, and move it up or down to the position that serves Use the following procedure to untwist a twisted lap/ you best. shoulder belt. Lap/Shoulder Belt Untwisting Procedure 1. Position the latch plate as close as possible to the anchor point. 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 you will prefer a higher position. When you release the anchorage, try to move it up or down to make sure that it is locked in position. Rear Seat Belts First Row Second Row Driver N/A ALR Center N/A ALR Passenger ALR ALR The shoulder belt anchorages of the rear three-point belts • N/A — Not Applicable are nonadjustable for outboard and center rear passengers on sedans.
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Automatic Locking Retractor Mode (ALR) — If Equipped In this mode, the shoulder belt is automatically prelocked. The belt will still retract to remove any slack in the shoulder belt. The Automatic Locking Mode is available on all passenger-seating positions with a combination lap/shoulder belt. Use the Automatic Locking Mode anytime a child safety seat is installed in a seating position that has a belt with this feature.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 NOTE: These devices are not a substitute for proper seat belt placement by the occupant. The seat belt still must be This vehicle has a safety belt system with an Energy worn snugly and positioned properly. Management feature in the front seating positions to help further reduce the risk of injury in the event of a head-on The pretensioners are triggered by the Occupant Restraint Controller (ORC). Like the air bags, the pretencollision.
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE How The Active Head Restraints (AHR) Work The Occupant Restraint Controller (ORC) determines whether the severity, or type of rear impact will require the Active Head Restraints (AHR) to deploy. If a rear impact requires deployment, both the driver and front passenger seat AHRs will be deployed. When AHRs deploy during a rear impact, the front half of the head restraint extends forward to minimize the gap between the back of the occupant’s head and the AHR.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 CAUTION! 1. Grasp the deployed AHR from the rear seat. All occupants, including the driver, should not operate a vehicle or sit in a vehicle’s seat until the head restraints are placed in their proper positions in order to minimize the risk of neck injury in the event of a collision.
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 1 — Downward Movement 2 — Rearward Movement 3 — Final Downward Movement To Engage Locking Mechanism 4. The AHR front soft foam and trim half should lock into the back decorative plastic half.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 • For safety reasons, have the Active Head Restraints checked by a qualified specialist at an authorized dealer. Enhanced Seat Belt Use Reminder System (BeltAlert®) AHR In Reset Position NOTE: BeltAlert® is a feature intended to remind the driver and front passenger (if equipped with front passenger BeltAlert®) to fasten their seat belts. The feature is active whenever the ignition is on.
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Light remains illuminated until the respective seat belts are fastened. The driver should instruct all other occupants to fasten their seat belts. If a front seat belt is unbuckled while traveling at speeds greater than 5 mph (8 km/h), BeltAlert® will provide both audio and visual notification. The front passenger seat BeltAlert® is not active when the front passenger seat is unoccupied.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 dealer can provide you with a seat belt extender. This passenger’s Advanced Front Air Bag is mounted in the extender should be used only if the existing belt is not instrument panel, above the glove compartment. The long enough. When it is not required, remove the ex- words SRS AIRBAG are embossed on the air bag covers. tender and store it. WARNING! Using a seat belt extender when not needed can increase the risk of injury in a collision.
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: The Driver and Passenger Advanced Front Air vehicle is equipped with SABIC, they are located above Bags are certified to new Federal regulations. the side windows. The trim covering the side air bags is labeled SRS AIRBAG. The Advanced Front Air Bags have a multistage inflator design.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 • Air Bag Warning Light • Steering Wheel and Column • Instrument Panel • Knee Impact Bolsters • Driver Advanced Front Air Bag • Passenger Advanced Front Air Bag • Supplemental Seat-Mounted Side Air Bags (SAB) • Supplemental Side Air Bag Inflatable Curtains (SABIC) • Front and Side Impact Sensors • Front Seat Belt Pretensioners, Seat Belt Buckle Switch, and Seat Track Position Sensors output appropriate to the severity and type of collision as determined by th
62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • Do not put anything on or around the air bag covers or attempt to open them manually. You may damage the air bags and you could be injured because the air bags may no longer be functional. The protective covers for the air bag cushions are designed to open only when the air bags are inflating. • Do not drill, cut or tamper with the knee bolster in any way.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 When the air bag deploys, it opens the seam between the front and side of the seat’s trim cover. Each air bag deploys independently; a left side impact deploys the left air bag only and a right-side impact deploys the right air bag only. Supplemental Side Air Bag Inflatable Curtain (SABIC) SABIC air bags may offer side-impact protection to front and rear seat outboard occupants in addition to that provided by the body structure.
64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Being too close to the SAB and SABIC air bags during deployment could cause you to be severely injured or killed. The system includes side impact sensors that are calibrated to deploy the side air bags during impacts that require air bag occupant protection. WARNING! • Your vehicle is equipped with left and right Supplemental Side Air Bag Inflatable Curtain (SABIC), do not stack luggage or other cargo up high enough to block the location of the SABIC.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 seriously injured or killed. Occupants, especially chil- Air Bag Deployment Sensors And Controls dren, should not lean on or sleep against the door, side Occupant Restraint Controller (ORC) windows, or area where the SAB or SABIC air bags The ORC is part of a Federally regulated safety system inflate, even if they are in an infant or child restraint. required for this vehicle.
66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The Advanced Front Air Bags will not deploy in all frontal collisions, including some that may produce substantial vehicle damage — for example, some pole collisions, truck underrides, and angle offset collisions. On the other hand, depending on the type and location of impact, Advanced Front Air Bags may deploy in crashes with little vehicle front-end damage but that produce a severe initial deceleration.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 It also includes diagnostics that will illuminate the instrument cluster Air Bag Warning Light if a malfunction is noted that could affect the air bag system. The diagnostics also record the nature of the malfunction. WARNING! Ignoring the Air Bag Warning Light in your instrument panel could mean you won’t have the air bags to protect you in a collision.
68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Supplemental Seat-Mounted Side Air Bag (SAB) Inflator Units Supplemental Side Air Bag Inflatable Curtain (SABIC) Inflator Units The Supplemental Seat-Mounted Side Air Bags (SAB) are During collisions where the impact is confined to a designed to activate only in certain side collisions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 Because air bag sensors estimate deceleration over time, • Turn on the interior lights, which remain on as long as the battery has power or until the ignition key is vehicle speed and damage are not good indicators of removed. whether or not an air bag should have deployed. Front And Side Impact Sensors • Unlock the doors automatically.
70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If you do have a collision, which deploys the air bags, any or all of the following may occur: throat irritation, move to fresh air. If the irritation continues, see your doctor. If these particles settle on your clothing, follow the garment manufacturer’s instructions for cleaning. • The nylon air bag material may sometimes cause abrasions and/or skin reddening to the driver and front passenger as the air bags deploy and unfold.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 Maintaining Your Air Bag System WARNING! (Continued) WARNING! • Modifications to any part of the air bag system could cause it to fail when you need it. You could be injured if the air bag system is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the steering wheel hub trim cover or the upper right side of the instrument panel.
72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Air Bag Warning Light NOTE: If the speedometer, tachometer, or any engine related gauges are not working, the Occupant Restraint Controller (ORC) may also be disabled. The air bags may not be ready to inflate for your protection. Promptly check the fuse block for blown fuses. Refer to the label located on the inside of the fuse block cover for the proper air bag fuses. See your authorized dealer if the fuse is good.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 • Whether or not the driver and passenger safety belts In addition to the vehicle manufacturer, other parties, were buckled/fastened; such as law enforcement, that have the special equipment, can read the information if they have access to the • How far (if at all) the driver was depressing the vehicle or the EDR. accelerator and/or brake pedal; and, Child Restraints • How fast the vehicle was traveling.
74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! In a collision, an unrestrained child can become a projectile inside the vehicle. The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are. The child and others could be badly injured. Any child riding in your vehicle should be in a proper restraint for the child’s size.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 Summary Of Recommendations For Restraining Children In Vehicles Infants and Toddlers Small Children Larger Children Children Too Large for Child Restraints Child Size, Height, Weight Or Age Children who are two years old or younger and who have not reached the height or weight limits of their child restraint Children who are at least two years old or who have out-grown the height or weight limit of their rear-facing child restraint Children who have out-g
76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Infants And Child Restraints Safety experts recommend that children ride rearwardfacing in the vehicle until they are two years old or until they reach either the height or weight limit of their rear facing child safety seat. Two types of child restraints can be used rearward-facing: infant carriers and convertible child seats. The infant carrier is only used rearward-facing in the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77 have outgrown the rear-facing weight or height limit of their rear-facing convertible child seat. Children should remain in a forward-facing child seat with a harness for as long as possible, up to the highest weight or height allowed by the child seat. All children whose weight or height is above the forward-facing limit for the child seat should use a belt-positioning booster seat until the vehicle’s seat belts fit properly.
78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE seatback, should use the seat belt in a rear seat. Use this child is using the lap/shoulder belt, check belt fit perisimple 5-step test to decide whether the child can use the odically and make sure the seat belt buckle is latched. A vehicle’s seat belt alone: child’s squirming or slouching can move the belt out of position. If the shoulder belt contacts the face or neck, 1.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 79 Recommendations For Attaching Child Restraints Restraint Type Combined Weight of the Child + Child Restraint Rear-Facing Child Restraint Rear-Facing Child Restraint Forward-Facing Child Restraint Forward-Facing Child Restraint Up to 65 lbs (29.5 kg) More than 65 lbs (29.5 kg) Up to 65 lbs (29.5 kg) More than 65 lbs (29.
80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lower Anchors And Tethers For Children (LATCH) Restraint System Your vehicle is equipped with the child restraint anchorage system called LATCH, which stands for Lower Anchors and Tethers for CHildren. The LATCH system has three vehicle anchor points for installing LATCHequipped child seats. There are two lower anchorages located at the back of the seat cushion where it meets the seatback and one top tether anchorage located behind the seating position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 81 LATCH Positions For Installing Child Restraints In This Vehicle 2 • • Lower Anchorage Symbol 2 anchorages per seating position Top Tether Anchorage Symbol
82 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE What is the weight limit (child’s weight + weight of the child restraint) for using the LATCH anchorage system to attach the child restraint? 65 lbs (29.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 83 Can two child restraints be attached using a common lower LATCH anchorage? No Can the rear-facing child restraint touch the back of the front passenger seat? Yes Can the head restraints be removed? No Never “share” a LATCH anchorage with two or more child restraints.
84 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Locating The LATCH Anchorages The lower anchorages are round bars that are found at the rear of the seat cushion where it meets the seatback, below the anchorage symbols on the seatback. They are just visible when you lean into the rear seat to install the child restraint. You will easily feel them if you run your finger along the gap between the seatback and seat cushion.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 85 Locating The LATCH Anchorages In addition, there are tether strap anchorages behind each rear seating position located in the panel between the rear seatback and the rear window. They are found under a plastic cover with the tether anchorage symbol on it. 2 Tether Strap Anchorages LATCH-compatible child restraint systems will be equipped with a rigid bar or a flexible strap on each side.
86 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE tether strap. The tether strap will have a hook at the end to attach to the top tether anchorage and a way to tighten the strap after it is attached to the anchorage. Center Seat LATCH WARNING! (Continued) seat belt for installing child seats in the outboard positions. Please refer to “Installing The LATCHCompatible Child Restraint System” for typical installation instructions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 87 2. Loosen the adjusters on the lower straps and on the 5. If the child restraint has a tether strap, connect it to the tether strap of the child seat so that you can more top tether anchorage. See the section “Installing Child Restraints Using the Top Tether Anchorage” for direceasily attach the hooks or connectors to the vehicle tions to attach a tether anchor. anchorages. 3. Place the child seat between the lower anchorages for 6.
88 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE with it and accidentally lock the seatbelt retractor. Before WARNING! (Continued) installing a child restraint using the LATCH system, • Child restraint anchorages are designed to withbuckle the seat belt behind the child restraint and out of stand only those loads imposed by correctly-fitted the child’s reach. If the buckled seat belt interferes with child restraints.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 89 make a clicking noise while the webbing is pulled back Lap/Shoulder Belt Systems for Installing Child into the retractor. For additional information on ALR, Restraints in this Vehicle refer to the “Automatic Locking Mode” description under “Occupant Restraints”. The cinching latch plate is designed to hold the lap portion of the seatbelt tight when webbing is pulled tight and straight through a child restraint’s belt path.
90 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE What is the weight limit (child’s weight + weight of the child restraint) for using the Tether Anchor with the seat belt to attach a forward facing child restraint? Can the rear-facing child restraint touch the back of the front passenger seat? Weight limit of the Child Restraint Can the head restraints be removed? Can the buckle stalk be twisted to tighten the seat belt against the belt path of the child restraint? No Yes Yes Always use the tether anchor
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 91 5. To lock the seat belt, pull down on the shoulder part of the belt until you have pulled all the seat belt webbing out of the retractor. Then, allow the webbing to retract 1. Place the child seat in the center of the seating back into the retractor. As the webbing retracts, you position. For some second row seats, you may need to will hear a clicking sound.
92 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 8. If the child restraint has a top tether strap and the Installing Child Restraints Using The Top Tether seating position has a top tether anchorage, connect Anchorage the tether strap to the anchorage and tighten the tether strap. See the section “Installing Child Restraints 1. Look behind the seating position where you Using the Top Tether Anchorage” for directions to plan to install the child restraint to find the attach a tether anchor. tether anchorage.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 93 between the two posts. If not possible, lower the head 4. Attach the tether strap hook of the child restraint to the top tether anchorage as shown in the diagram. restraint and pass the tether strap around the outboard side of the head restraint. 5. Remove slack in the tether strap according to the child restraint manufacturer’s instructions.
94 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE While cruising, brief full-throttle acceleration within the limits of local traffic laws contributes to a good break-in. Air Bags deploying in the front seat could harm your pet. Wide-open throttle acceleration in low gear can be detriAn unrestrained pet will be thrown about and possibly mental and should be avoided. injured, or injure a passenger during panic braking or in a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 95 NOTE: A new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered a normal part of the break-in and not interpreted as an indication of difficulty. SAFETY TIPS Transporting Passengers NEVER TRANSPORT PASSENGERS IN THE CARGO AREA. WARNING! • Do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death.
96 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) eventually poison you. To avoid breathing (CO), follow these safety tips: • Do not run the engine in a closed garage or in confined areas any longer than needed to move your vehicle in or out of the area. • If you are required to drive with the trunk/liftgate/ rear doors open, make sure that all windows are closed and the climate control BLOWER switch is set at high speed. DO NOT use the recirculation mode.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 97 Front seat belt assemblies must be replaced after a collision. Rear seat belt assemblies must be replaced after a collision if they have been damaged (i.e., bent retractor, torn webbing, etc.). If there is any question regarding belt or retractor condition, replace the belt. Air Bag Warning Light The light should come on and remain on for four to eight seconds as a bulb check when the ignition switch is first turned ON.
98 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) WARNING! (Continued) • Never place or install floor mats or other floor coverings in the vehicle that cannot be properly secured to prevent them from moving and interfering with the pedals or the ability to control the vehicle. • Never put floor mats or other floor coverings on top of already installed floor mats. Additional floor mats and other coverings will reduce the size of the pedal area and interfere with the pedals.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 99 Periodic Safety Checks You Should Make Outside The Vehicle Door Latches Tires Fluid Leaks Examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread or sidewall. Inspect the tread for cuts and cracks. Inspect sidewalls for cuts, cracks and bulges. Check the wheel nuts for tightness. Check the tires (including spare) for proper cold inflation pressure.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 䡵 MIRRORS . . . . . . . . . . . . . . . . . . . . . . . . . . . .105 ▫ Phone Call Features . . . . . . . . . . . . . . . . . . .119 ▫ Inside Day/Night Mirror . . . . . . . . . . . . . . . .105 ▫ Uconnect® Phone Features . . . . . . . . . . . . . .122 ▫ Automatic Dimming Mirror — If Equipped . . .106 ▫ Advanced Phone Connectivity . . . . . . . . . . . .127 ▫ Power Mirrors . . . . . . . . . . . . . . . . . . . . . . .
102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 䡵 SEATS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .146 䡵 LIGHTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . .162 ▫ Power Seats — If Equipped . . . . . . . . . . . . . .147 ▫ Multifunction Lever . . . . . . . . . . . . . . . . . . . .162 ▫ Heated Seats — If Equipped . . . . . . . . . . . . .150 ▫ Headlights And Parking Lights . . . . . . . . . . . .163 ▫ Manual Front Seat Adjustment . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 ▫ Daytime Running Lights (DRL) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . .167 ▫ Instrument Panel Dimmer . . . . . . . . . . . . . . .167 ▫ Map/Reading/Interior Lights . . . . . . . . . . . .168 ▫ Battery Saver Feature . . . . . . . . . . . . . . . . . .169 䡵 WINDSHIELD WIPERS AND WASHERS . . . . . .169 ▫ Intermittent Wiper System . . . . . . . . . . . . . . .170 ▫ Windshield Washers . . . . . . . . . . . . . . . . . . .171 ▫ Mist Feature .
104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Troubleshooting Tips . . . . . . . . . . . . . . . . . . .185 䡵 ELECTRICAL POWER OUTLETS . . . . . . . . . . .190 ▫ General Information. . . . . . . . . . . . . . . . . . . .186 䡵 CIGAR LIGHTER AND ASH RECEIVER — IF EQUIPPED . . . . . . . . . . . . . . . . . . . . . . . . . 䡵 POWER SUNROOF — IF EQUIPPED . . . . . . . .187 䡵 CUPHOLDERS . . . . . . . . . . . . . . . . . . . . . . ▫ Opening Sunroof — Express . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 MIRRORS Inside Day/Night Mirror A two-point pivot system allows for horizontal and vertical mirror adjustment. Adjust the mirror to center on the view through the rear window. 3 Headlight glare can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle). The mirror should be adjusted while set in the day position (toward the windshield).
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Dimming Mirror — If Equipped This mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light to the left of the button will illuminate to indicate when the dimming feature is activated. The sensor to the right of the button does not illuminate. NOTE: This feature is disabled when the vehicle is moving in reverse.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean. 3 Power Mirrors The power mirror control is located on the driver’s door trim panel. Power Mirror Control To adjust a mirror, turn the control wand toward the left or right mirror positions indicated. Tilt the control wand in the direction you want the mirror to move.
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Adjusting Side View Mirrors Outside Mirror — Driver Side Adjust the outside mirror to center on the adjacent lane of traffic, with a slight overlap of the view obtained on the inside mirror. Outside Mirror — Passenger Side Adjust the convex outside mirror so you can just see the side of your vehicle in the part of the mirror closest to the vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 WARNING! (Continued) collide with another vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in the passenger side convex mirror. Some vehicles will not have a convex passenger side mirror. Heated Mirrors — If Equipped These mirrors are heated to melt frost or ice. This feature can be activated whenever you turn on the rear window defroster (if equipped).
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE mobile phone’s audio is transmitted through your vehicle’s audio system; the system will automatically mute your radio when using the Uconnect® Phone. NOTE: The Uconnect® Phone requires a mobile phone equipped with the Bluetooth® “Hands-Free Profile”, Version 0.96 or higher. See the Uconnect® website for supported phones. For Uconnect® customer support: • U.S. residents - visit www.UconnectPhone.com or call 1-877-855-8400. • Canadian Residents - visit www.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 The Uconnect® Phone is driven through your WARNING! (Continued) Bluetooth® “Hands-Free Profile” mobile phone. Uconnect® features Bluetooth® technology - the global laws, including laws regarding phone use. Your atstandard that enables different electronic devices to con- tention should be focused on safely operating the nect to each other without wires or a docking station, so vehicle.
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Command Button Operation Actual button location may vary with the ra- Voice commands can be used to operate the Uconnect® dio. The individual buttons are described in the Phone and to navigate through the Uconnect® Phone menu structure. Voice commands are required after most “Operation” section. Uconnect® Phone prompts.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 part of the command when you are asked for it. For example, you can use the compound form voice command “Phonebook New Entry,” or you can break the compound form command into two voice commands: “Phonebook” and “New Entry.” Please remember, the Uconnect® Phone works best when you talk in a normal conversational tone, as if speaking to someone sitting a few feet/meters away from you. Voice Command Tree Refer to “Voice Tree” in this section.
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The following are general phone to Uconnect® Phone You will then be asked to give your mobile phone a priority level between one and seven, with one being the pairing instructions: highest priority. You can pair up to seven mobile phones button to begin. 1. Press the to your Uconnect® Phone. However, at any given time, 2. After the “Ready” prompt and the following beep, say only one mobile phone can be in use, connected to your “Device Pairing.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 • The system will prompt you to say the number you want to call. • For example, you can say “151-1234-5555.” • The Uconnect® Phone will confirm the phone number and then dial. The number will appear in the display of certain radios. Call By Saying A Name • Press the button to begin. or downloaded phonebook. To learn how to store a name in the phonebook, refer to “Add Names to Your Uconnect® Phonebook.
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Automatic download and update, if supported, begins • This downloaded phonebook cannot be edited or as soon as the Bluetooth® wireless phone connection is deleted on the Uconnect® Phone. These can only be edited on the mobile phone. The changes are transmade to the Uconnect® Phone, for example, after you ferred and updated to Uconnect® Phone on the next start the vehicle. phone connection.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 • When prompted, enter the number designation (e.g., Edit Uconnect® Phonebook Entries “Home,” “Work,” “Mobile,” or “Other”). This will NOTE: Editing phonebook entries is recommended allow you to store multiple numbers for each phonewhen the vehicle is not in motion. Automatic downbook entry, if desired. loaded phonebook entries cannot be deleted or edited. • When prompted, recite the phone number for the button to begin.
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE After you are finished editing an entry in the phonebook, • After you enter the Phonebook Delete menu, you will then be asked for the name of the entry that you wish you will be given the opportunity to edit another entry in to delete. You can either say the name of a phonebook the phonebook, call the number you just edited, or return entry that you wish to delete or you can say “List to the main menu.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 Delete/Erase “All” Uconnect® Phonebook Entries • Press the button to begin. • After the “Ready” prompt and the following beep, say “Phonebook Erase All.” • After the “Ready” prompt and the following beep, say “Phonebook List Names.” • The Uconnect® Phone will play the names of all the phonebook entries, including the downloaded phonebook entries, if available.
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE button to place the current mobile service plan. For example, if your mobile service mobile phone. Press the plan provides three-way calling, this feature can be call on hold and answer the incoming call. accessed through the Uconnect® Phone. Check with your NOTE: The Uconnect® Phone compatible phones in the mobile service provider for the features that you have.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 Place/Retrieve A Call From Hold To put a call on hold, press the button until you hear a single beep. This indicates that the call is on hold. To butbring the call back from hold, press and hold the ton until you hear a single beep. Three-Way Calling To initiate three-way calling, press the button while a call is in progress, and make a second phone call, as described under “Making a Second Call While Current Call is in Progress.
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Redial • Press the button to begin. ends, or until the vehicle battery condition dictates cessation of the call on the Uconnect® Phone and transfer of the call to the mobile phone. • After the “Ready” prompt and the following beep, say 2. After the ignition is cycled to OFF, a call can continue “Redial.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 • After the “Ready” prompt and the following beep, say If the phone is not reachable and the Uconnect® Phone is the name of the language you wish to switch to operational, you may reach the emergency number as follows: English, Espanol, or Francais. • Continue to follow the system prompts to complete the • language selection. • After selecting one of the languages, all prompts and voice commands will be in that language. Press the button to begin.
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • If supported, this number may be programmable on • After the “Ready” prompt and the following beep, say “Towing Assistance.” button and say some systems. To do this, press the “Setup,” followed by “Emergency.” NOTE: You should program the desired Towing Assis• The Uconnect® Phone does slightly lower your tance phone number using the Voice Command system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 “Send,” is also to be used for navigating through an automated customer service center menu structure, and This method is used in instances where one generally has to leave a number on a pager. to press numbers on the mobile phone keypad while navigating through an automated telephone system.
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Some paging and voice mail systems have system time • After the “Ready” prompt and the following beep, say one of the following: out settings that are too short and may not allow the use of this feature. – “Setup Confirmation Prompts On” Barge In — Overriding Prompts – “Setup Confirmation Prompts Off” The “Voice Command” button can be used when you wish to skip part of a prompt and issue your voice command immediately.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 dialing a number with your paired Bluetooth® mobile • Following the beep, say “Mute.” phone, the audio will be played through your vehicle’s To un-mute the Uconnect® Phone: audio system. The Uconnect® Phone will work the same • Press the button. as if you dial the number using Voice Command. NOTE: Certain brands of mobile phones do not send the dial ring to the Uconnect® Phone to play it on the vehicle audio system, so you will not hear it.
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Connect Or Disconnect Link Between The Uconnect® Phone And Mobile Phone lowest priority. To “Select” or “Delete” a paired phone being announced, press the button and say “Select” or “Delete.” Also, see the next two sections for an alternate way to “Select” or “Delete” a paired phone. Your mobile phone can be paired with many different electronic devices, but can only be actively “connected” with one electronic device at a time.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 Uconnect® Phone will return to using the highest Things You Should Know About Your Uconnect® priority phone present in or near (approximately Phone within 30 ft. [9 m]) the vehicle. Uconnect® Phone Tutorial Delete Uconnect® Phone Paired Mobile Phones To hear a brief tutorial of the system features, press the • Press the button to begin. button and say “Uconnect® Tutorial.
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE button and say the “Voice Training,” This will delete all phone pairing, phone book entries, • Press the “System Training,” or “Start Voice Training” com- and other settings in all language modes. The System will prompt you before resetting to factory settings. mand.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 • Low-to-medium vehicle speed • Low road noise • Smooth road surface • Phonebook (Downloaded and Uconnect® Phone Local) name recognition rate is optimized when the entries are not similar. • Fully closed windows • Numbers must be spoken in single digits. “800” must be spoken “eight-zero-zero” not “eight hundred.” • Dry weather condition • You can say “O” (letter “O”) for “0” (zero).
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Low Road Noise Recent Calls • Smooth Road Surface • Fully Closed Windows If your phone supports “Automatic Phonebook Download,” Uconnect® Phone can list your Outgoing, Incoming and Missed Calls. • Dry Weather Conditions Voice Text Reply • Operation From The Driver’s Seat Uconnect® Phone can read or send new messages on • Performance, such as audio clarity, echo, and loudness your phone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 3. Uconnect® Phone will play the new text message for List of Preset Messages: you. 1. Yes. After reading a message, you can “Reply” or “Forward” 2. No. the message using Uconnect® Phone. 3. Where are you? Send Messages: 4. I need more direction. You can send messages using Uconnect® Phone. To send 5. L O L. a new message: 1. Press the button. 6. Why? 2. After the “Ready” prompt and the following beep, say 7. I love you. “SMS Send” or “Send Message.” 8.
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 13. I’ll be late. 14. Are you there yet? 15. Where are we meeting? 16. Can this wait? • After the “Ready” prompt and the following beep, say “Setup, Incoming Message Announcement,” you will then be given a choice to change it. Bluetooth® Communication Link 19. Send number to call. Mobile phones have been found to lose connection to the Uconnect® Phone. When this happens, the connection can generally be reestablished by switching the phone off/on.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 3
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 3
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Commands Primary Alternate (s) zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location Voice Commands Primary Alternate (s) all call cancel confirmation prompts continue delete dial download edit emergency English erase all Espanol Francais
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 Voice Commands Primary Alternate (s) help home language list names list phones mobile mute mute off new entry no other pair a phone phone pairing pairing phonebook phone book Voice Commands Primary Alternate (s) previous record again redial return to main menu return or main menu select phone select send set up phone settings or phone set up towing assistance transfer call Uconnect® Tutorial voice training work yes 3
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE General Information VOICE COMMAND — IF EQUIPPED This device complies with Part 15 of the FCC rules and Voice Command System Operation RSS 210 of Industry Canada.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 WARNING! Any voice commanded system should be used only in safe driving conditions following all applicable laws, including laws regarding phone use. Your attention should be focused on safely operating the vehicle. Failure to do so may result in a collision causing serious injury or death. Pressing the Voice Command button while the system is speaking is known as “barging in.
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To hear the first available Menu, press the Voice Com- 3. Use the ON/OFF VOLUME rotary knob to adjust the volume to a comfortable level while the Voice Combutton and say “Help” or “Main Menu.” mand mand system is speaking. Please note the volume Commands setting for Voice Command is different than the audio The Voice Command system understands two types of system. commands, Universal commands and Local commands.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 • “Bluetooth Streaming” (to switch to Bluetooth® Radio FM Streaming mode) To switch to the FM band, say “FM” or “Radio FM.” In this mode, you may say the following commands: • “Memo” (to switch to the memo recorder) • “System Setup” (to switch to system setup) • “Frequency #” (to change the frequency) Radio AM • “Next Station” (to select the next station) To switch to the AM band, say “AM” or “Radio AM.
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • “Next Channel” (to select the next channel) USB Mode • “Previous Channel” (to select the previous channel) To switch to USB mode, say “USB.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 Memo Mode – “Previous” (to play the previous memo) To switch to the voice recorder mode, say “Memo.” In this mode, you may say the following commands: – “Delete” (to delete a memo) – “Delete All” (to delete all memos) • “New Memo” (to record a new memo) — During the Setup recording, you may press the Voice Command button to stop recording.
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • “Tutorial” • “Voice Training” parked, engine running, all windows closed, and the blower fan switched off. This procedure may be repeated with a new user. The system will adapt to the last trained voice only. NOTE: Keep in mind that you have to press the Voice button first and wait for the beep Command SEATS before speaking the “Barge In” commands. Seats are a part of the Occupant Restraint System of the Voice Training vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 WARNING! (Continued) • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Be sure everyone in your vehicle is in a seat and using a seat belt properly. 3 Power Seats — If Equipped The power seat switches are located on the outboard side of the seat near the floor.
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! CAUTION! • Adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • Seats should be adjusted before fastening the seat belts and while the vehicle is parked. Serious injury or death could result from a poorly adjusted seat belt. • Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 Tilting The Seat Up Or Down The angle of the seat cushion can be adjusted in four directions. Pull upward or push downward on the front or rear of the seat switch, the front or rear of the seat cushion will move in the direction of the switch. Release the switch when the desired position has been reached. Reclining The Seatback The angle of the seatback can be adjusted forward or rearward.
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Do not place any article under a power seat or impede its ability to move as it may cause damage to the seat controls. Seat travel may become limited if movement is stopped by an obstruction in the seat’s path. Heated Seats — If Equipped There are two heated seat switches that allow the driver and passenger to operate the seats independently. The controls for each heater are located on the center of the instrument panel (above the climate controls).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 indicating the change. The LOW-level setting will turn OFF Manual Front Seat Adjustment automatically after approximately 30 minutes. The manual seat adjustment bar is at the front of the seat, near the floor. WARNING! • Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion or other physical condition must exercise care when using the seat heater.
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Pull the bar upward to move the seat forward or rearward. Release the bar once the seat is in the position desired. Then, using body pressure, move forward and rearward on the seat to be sure that the seat adjusters have latched. WARNING! Driver Seat Manual Height Adjuster — If Equipped A lever style height adjustment feature enhances comfort for petite as well as tall drivers.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 Reclining Seats The recline lever is located on the side of the seat. To recline, lean forward slightly before lifting the lever, then lean back to the desired position and release the lever. Lean forward and lift the lever to return the seatback to its normal position. WARNING! • Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control.
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! The head restraints for all occupants must be properly adjusted prior to operating the vehicle or occupying a seat. Head restraints should never be adjusted while the vehicle is in motion. Driving a vehicle with the head restraints improperly adjusted or removed could cause serious injury or death in the event of a collision.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 between the back of the occupant’s head and the AHR. This system is designed to help prevent or reduce the extent of injuries to the driver and front passenger in certain types of rear impacts. Refer to “Occupant Restraints” in “Things To Know Before Starting Your Vehicle” for further information. 3 To raise the head restraint, pull upward on the head restraint.
156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE For comfort the Active Head Restraints can be tilted forward and rearward. To tilt the head restraint closer to the back of your head, pull forward on the bottom of the head restraint. Push rearward on the bottom of the head restraint to move the head restraint away from your head. Active Head Restraint (Tilted) NOTE: Active Head Restraint (Normal Position) • The head restraints should only be removed by qualified technicians, for service purposes only.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 • In the event of deployment of an Active Head Restraint, refer to “Occupant Restraints/Resetting Active Head Restraints (AHR)” in “Things to Know Before Starting Your Vehicle” for further information. WARNING! • Do not place items over the top of the Active Head Restraint, such as coats, seat covers or portable DVD players.
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The hard seatback features a work surface and a molded The recline handle on the front passenger seat also rim for retaining items stored on the seatback panel. releases the seatback to fold forward.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 When returning the rear seatback to the upright position, To provide additional storage area, the rear seatback can be sure the seatback is latched. be folded forward. Pull on the loops to fold down either WARNING! or both seatbacks. Folding Rear Seat • Be certain that the seatback is securely locked into position. If the seatback is not securely locked into position the seat will not provide the proper stability for child seats and/or passengers.
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Folding Rear Seat Center Armrest TO OPEN AND CLOSE THE HOOD The rear seat is equipped with a folding armrest with To open the hood, two latches must be released. cupholders. 1. Pull the hood release lever located under the left side of the instrument panel.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 2. Then lift the secondary latch located under the front edge of the hood, near the center and raise the hood. 3 Prop Rod Location Hood Safety Latch Location Use the hood prop rod to secure the hood in the open position. Place the upper end of the prop rod in the hole on the left underside of the hood. NOTE: Before closing the hood, make sure to stow the prop rod in its proper location.
162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! To prevent possible damage, do not slam the hood to close it. Use a firm downward push at the center of the hood to ensure that both latches engage. passing light, fog lights, instrument panel light dimming and turn signals. The multifunction lever is located on the left side of the steering column. WARNING! Be sure the hood is fully latched before driving your vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 Headlights And Parking Lights Automatic Headlights — If Equipped Turn the end of the multifunction lever to the first detent Turning the end of the multifunction lever to the third for parking light operation. Turn to the second detent for detent (AUTO), will activate the automatic headlight headlight operation. system.
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE With the engine running and the multifunction lever in Headlight Time Delay the AUTO position, the headlights will turn on and turn There is also a feature that delays turning off the vehicle off based on the surrounding light levels. lights for 30, 60 or 90 seconds after the ignition switch is Headlights With Wipers (Available With Automatic turned OFF.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 NOTE: If either light remains on and does not flash, or Move the multifunction lever up or down and the arrows there is a very fast flash rate, check for a defective outside on each side of the instrument cluster flash to show light bulb. If an indicator fails to light when the lever is moved, it would suggest that the indicator bulb is proper operation of the front and rear turn signal lights. defective.
166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Flash-To-Pass You can signal another vehicle with your headlights by lightly pulling the multifunction lever toward you. This will turn on the high beam headlights until the lever is released. NOTE: If the multifunction lever is held in the flash-topass position for more than 15 seconds, the high beams will shut off. If this occurs, wait 30 seconds for the next flash-to-pass operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 Rotate the center portion of the lever upward to the next detent position to brighten the odometer and radio when The front turn signal lamps will turn on as Daytime the parking lights or headlights are on.
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Map/Reading/Interior Lights These lights are mounted between the sun visors above the rearview mirror. Each light can be turned on by pressing the barrel. Press the barrel a second time to turn the light off. Both of these lights can swivel so that the light can be aimed at a specific spot, if desired. The lights will remain on until the switch is pressed a second time, so be sure they have been turned off before leaving the vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 because a door is open. To restore interior light operation, either turn the ignition switch ON or cycle the light switch. Battery Saver Feature To protect the battery, the interior lights will turn off automatically 10 minutes after the ignition switch is moved to the LOCK position. This will occur if the interior lights were switched on manually or are on because a door is open.
170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! • Turn the windshield wipers off when driving through an automatic car wash. Damage to the windshield wipers may result if the wiper control is left in any position other than off. • Always remove any buildup of snow that prevents the windshield wiper blades from returning to the off position. If the windshield wiper control is turned off and the blades cannot return to the off position, damage to the wiper motor may occur.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 regulate the wipe interval from a minimum of one cycle Windshield Washers every second to a maximum of approximately 18 seconds To use the washer, pull the windshield wiper/washer between cycles. control lever toward you and hold it for as long as washer spray is desired.
172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! (Continued) the windshield during freezing weather, warm the windshield with defroster before and during windshield washer use. Mist Feature Push down on the wiper control lever to activate a single wipe to clear the windshield of road mist or spray from a passing vehicle. As long as the lever is held down, the wipers will continue to operate.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173 column) is placed in the AUTO position. In addition, the headlights will turn off when the wipers are turned off if they were turned on by this feature. The headlights with wipers feature can be turned on or off through the Electronic Vehicle Information Center (EVIC) — if equipped. Refer to “Electronic Vehicle Information Center (EVIC)/Personal Settings (CustomerProgrammable Features)” in “Understanding Your Instrument Panel” for further information.
174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Do not adjust the steering column while driving. Adjusting the steering column while driving or driving with the steering column unlocked, could cause the driver to lose control of the vehicle. Failure to follow this warning may result in serious injury or death. ELECTRONIC SPEED CONTROL — IF EQUIPPED When engaged, the Electronic Speed Control takes over accelerator operations at speeds greater than 25 mph (40 km/h).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175 NOTE: In order to ensure proper operation, the Electronic Speed Control System has been designed to shut down if multiple Speed Control functions are operated at the same time. If this occurs, the Electronic Speed Control System can be reactivated by pushing the Electronic Speed Control ON/OFF button and resetting the desired vehicle set speed. WARNING! Leaving the Electronic Speed Control system on when not in use is dangerous.
176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Deactivate The speed increment shown is dependant on the speed of U.S. (mph) or Metric (km/h) units: A soft tap on the brake pedal, pushing the CANCEL button, or normal brake pressure while slowing the U.S. Speed (mph) vehicle will deactivate the Electronic Speed Control with• Pressing the RES (+) button once will result in a 1 mph out erasing the set speed memory. increase in set speed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177 • If the button is continually pressed, the set speed will continue to decrease until the button is released, then When the Electronic Speed Control is set, you can dethe new set speed will be established. crease speed by pushing the SET (-) button. The speed decrement shown is dependant on the speed To Accelerate For Passing To Decrease Speed of U.S. (mph) or Metric (km/h) units: U.S. Speed (mph) Press the accelerator as you would normally.
178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Electronic Speed Control can be dangerous where the system cannot maintain a constant speed. Your vehicle could go too fast for the conditions, and you could lose control and have an accident. Do not use Electronic Speed Control in heavy traffic or on roads that are winding, icy, snow-covered or slippery. The HomeLink® buttons, located on either the overhead console, headliner or sunvisor, designate the three different HomeLink® channels.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179 For more efficient programming and accurate transmission of the radio-frequency signal it is recommended that a new battery be placed in the hand-held transmitter of the device that is being programmed to the HomeLink® system. Erase all channels before you begin programming. To erase the channels place the ignition in the ON/RUN position and press and hold the two outside HomeLink® buttons (I and III) for up 20 seconds or until the red indicator flashes.
180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Programming A Rolling Code For programming garage door openers that were manufactured after 1995. These garage door openers can be identified by the “LEARN” or “TRAIN” button located where the hanging antenna is attached to the garage door opener. It is NOT the button that is normally used to open and close the door. The name and color of the button may vary by manufacturer. Training The Garage Door Opener 1 — Door Opener 2 — Training Button 1.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181 2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) away from the HomeLink® button you wish to program while keeping the HomeLink® indicator light in view. there may be a light that blinks when the garage door opener/device is in the LEARN/TRAIN mode. NOTE: You have 30 seconds in which to initiate the next 3. Simultaneously press and hold both the Homelink® step after the LEARN button has been pressed.
182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) away from the HomeLink® button you wish to proTo reprogram a channel that has been previously trained, gram while keeping the HomeLink® indicator light in follow these steps: view. 1. Cycle the ignition to the ON/RUN position. 3. Simultaneously press and hold both the Homelink® 2.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 183 • To program the two remaining HomeLink® buttons, Canadian/Gate Operator Programming repeat each step for each remaining button. DO NOT For programming transmitters in Canada/United States erase the channels. that require the transmitter signals to “time-out” after several seconds of transmission.
184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) 5. Press and hold the programmed HomeLink® button away from the HomeLink® button you wish to proand observe the indicator light. gram while keeping the HomeLink® indicator light in • If the indicator light stays on constantly, programview. ming is complete and the garage door/device should activate when the HomeLink® button is pressed. 3.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 185 3. Without releasing the button proceed with The HomeLink® Universal Transceiver is disabled when “Canadian/Gate Operator Programming” step 2 and the Vehicle Security Alarm is active. follow all remaining steps. Troubleshooting Tips Using HomeLink® If you are having trouble programming HomeLink®, To operate, press and release the programmed here are some of the most common solutions: HomeLink® button.
186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! WARNING! (Continued) Vehicle exhaust contains carbon monoxide, a dangerous gas. Do not run your vehicle in the garage while programming the transceiver. Exhaust gas can cause serious injury or death. use a garage door opener without these safety features. Call toll-free 1–800–355–3515 or, on the Internet at www.HomeLink.com for safety information or assistance.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 187 NOTE: • The transmitter has been tested and it complies with FCC and IC rules. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the device. 3 • The term IC before the certification/registration number only signifies that Industry Canada technical specifications were met. POWER SUNROOF — IF EQUIPPED The sunroof controls are mounted between the dome/ reading lights.
188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Never leave children alone in a vehicle, or with access to an unlocked vehicle. Never leave the Key Fob in or near the vehicle, or in a location accessible to children. Occupants, particularly unattended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death. • In a collision, there is a greater risk of being thrown from a vehicle with an open sunroof.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 189 position. The sunroof will close fully and stop automati- NOTE: If three consecutive sunroof close attempts result cally. This is called “Express Close”. During Express in Pinch Protect reversals, the fourth close attempt will be Close operation, any movement of the switch will stop a Manual Close movement with Pinch Protect disabled. the sunroof.
190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Wind Buffeting Ignition Off Operation Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occurrence and can be minimized. If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 191 The instrument panel power outlet, located below the A second power outlet is located inside the center conclimate control knobs, has power available only when the sole. ignition is ON. This power outlet will also operate a conventional cigar lighter unit. 3 Center Console Power Outlet The center console power outlet is powered directly from the battery (power available at all times).
192 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: To ensure proper operation a MOPAR® knob and element must be used. CAUTION! • Do not exceed the maximum power of 160 Watts (13 Amps) at 12 Volts. If the 160 Watt (13 Amp) power rating is exceeded the fuse protecting the system will need to be replaced. • Power outlets are designed for accessory plugs only. Do not insert any other object in the power outlets as this will damage the outlet and blow the fuse.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 193 WARNING! CAUTION! To avoid serious injury or death: • Only devices designed for use in this type of outlet should be inserted into any 12 Volt outlet. • Do not touch with wet hands. • Close the lid when not in use and while driving the vehicle. • If this outlet is mishandled, it may cause an electric shock and failure. • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.).
194 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CIGAR LIGHTER AND ASH RECEIVER — IF EQUIPPED An optional ash receiver is available from your authorized dealer and will fit in the center console front cupholder. The optional ash receiver also comes with a cigar lighter that can be used with the power outlets. Refer to “Power Outlets” in “Understanding The Features Of Your Vehicle” for further information.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 195 3 Rear Cupholders Rear Seat Bottle Holder There are built-in bottle holders located in both rear door trim panels. Rear Bottle Holder WARNING! If containers of hot liquid are placed in the bottle holder, they can spill when the door is closed, burning the occupants. Be careful when closing the doors to avoid injury.
196 UNDERSTANDING THE FEATURES OF YOUR VEHICLE STORAGE CONSOLE FEATURES Glove Compartment The glove compartment is located on the right side of the instrument panel. To open the glove compartment, pull outward on the latch handle located on the front of the glove compartment. Storage Glove Compartment The center console is located between the front driver and passenger seats. The center console armrest slides forward from design position to provide added user comfort.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 197 3 Center Console Armrest Center Console Storage Two separate storage compartments are also located The top compartment holds small items, such as a pen underneath the armrest. and note pad, while the larger bottom compartment will hold CDs and alike. The bottom compartment also contains a 12 Volt power outlet. The console’s front opening lid allows for easy access to these compartments.
198 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: CARGO AREA FEATURES • A notch in the front of the console base allows for use The 60/40 split-folding rear seat provides cargo-carrying of a cellular phone while it is plugged into the power versatility. The seatbacks fold down easily by pulling nylon tabs between the seatbacks and the bolsters. When outlet with the armrest latched down.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 199 WARNING! (Continued) • The cargo area in the rear of the vehicle (with the rear seatbacks in the locked-up or folded down position) should not be used as a play area by children when the vehicle is in motion. They could be seriously injured in a collision. Children should be seated and using the proper restraint system. • To help protect against personal injury, passengers should not be seated in the rear cargo area.
200 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Ski Pass-Through REAR WINDOW FEATURES There is a ski pass-through door located behind the rear Rear Window Defroster seat armrest that allows longer items, such as snow skis, to be stored in the rear cargo area. Lower the armrest and The rear window defroster button is located on pull downward on the latch to open the ski pass-through the climate control (Mode) knob. Press this button door.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 201 CAUTION! Failure to follow these cautions can cause damage to the heating elements: • Use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements. Labels can be peeled off after soaking with warm water.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 INSTRUMENT PANEL FEATURES . . . . . . . . . .206 ▫ EVIC Main Menu . . . . . . . . . . . . . . . . . . . . .228 䡵 INSTRUMENT CLUSTER . . . . . . . . . . . . . . . . .207 ▫ Compass Display . . . . . . . . . . . . . . . . . . . . .229 䡵 INSTRUMENT CLUSTER DESCRIPTIONS . . . . .208 ▫ Average Fuel Economy. . . . . . . . . . . . . . . . . .231 䡵 MINI-TRIP COMPUTER — IF EQUIPPED . . . . .222 ▫ Distance To Empty (DTE) . . . . . . . . . . . . . . . .
204 UNDERSTANDING YOUR INSTRUMENT PANEL 䡵 SETTING THE ANALOG CLOCK . . . . . . . . . . .236 ▫ Operating Instructions — Radio Mode . . . . . .247 䡵 Uconnect® 730N/430/430N CD/DVD/HDD/ NAV — IF EQUIPPED . . . . . . . . . . . . . . . . . . .237 ▫ Operation Instructions — CD MODE For CD And MP3 Audio Play . . . . . . . . . . . . . . .253 ▫ Operating Instructions (Voice Command System) — If Equipped . . . . . . . . . . . . . . . . .237 ▫ Notes On Playing MP3 Files . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 205 ▫ List Or Browse Mode . . . . . . . . . . . . . . . . . . .267 䡵 RADIO OPERATION AND MOBILE PHONES . .272 ▫ Bluetooth® Streaming Audio (BTSA) . . . . . . .269 䡵 CLIMATE CONTROLS . . . . . . . . . . . . . . . . . . .273 䡵 STEERING WHEEL AUDIO CONTROLS — IF EQUIPPED . . . . . . . . . . . . . . . . . . . . . . . . .270 ▫ Manual Heating And Air Conditioning . . . . . .273 ▫ Radio Operation . . . . . . . . . . . . . . . . . . . . . .
206 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT PANEL FEATURES 1 2 3 4 5 — Air Outlet — Side Window Demister Outlet — Instrument Cluster — Ignition Switch — Analog Clock 6 — Radio 7 — Passenger Airbag 8 — Glove Compartment 9 — Heated Seat Switch – If Equipped 10 — Hazard Switch 11 — Storage Compartment 12 — Climate Control 13 — Trunk Release Button 14 — Power Outlet
UNDERSTANDING YOUR INSTRUMENT PANEL 207 INSTRUMENT CLUSTER 4
208 UNDERSTANDING YOUR INSTRUMENT PANEL removes this heat. You can also turn the Temperature control to maximum heat, the Mode control to Floor and 1. Temperature Gauge the Fan control to High. This allows the heater core to act The temperature gauge shows engine coolant tempera- as a supplement to the radiator and aids in removing heat ture. Any reading below the red mark of the gauge shows from the engine cooling system. that the engine cooling system is operating properly. The 2.
UNDERSTANDING YOUR INSTRUMENT PANEL 209 5. Low Fuel Light If jump starting is required, refer to “Jump Starting Procedures” in “What To Do In Emergencies”. When the fuel level drops to approximately 2.0 gallons (7.6 Liters), the fuel symbol will light and 7. Air Bag Warning Light a single chime will sound. This light will turn on for four to eight seconds as a bulb check when the ignition switch is first NOTE: This light will remain on until a minimum of turned to ON/RUN.
210 UNDERSTANDING YOUR INSTRUMENT PANEL flash or remain on continuously. Refer to “Occupant 10. Engine Temperature Warning Light Restraints” in “Things To Know Before Starting Your This light warns of an overheated engine condiVehicle” for further information. tion. As engine coolant temperatures rise and the 9. Oil Pressure Warning Light gauge approaches H, this indicator will illuminate and a single chime will sound after reaching a set threshold. This light indicates low engine oil pressure.
UNDERSTANDING YOUR INSTRUMENT PANEL 211 11. Brake Warning Light This light monitors various brake functions, including brake fluid level and parking brake application. If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the anti-lock brake system. The dual brake system provides a reserve braking capacity in the event of a failure to a portion of the hydraulic system.
212 UNDERSTANDING YOUR INSTRUMENT PANEL off unless the parking brake is applied or a brake fault is NOTE: You must apply the brakes before shifting from detected. If the light does not illuminate, have the light PARK. inspected by an authorized dealer. 14. Odometer Display/Trip Odometer Display The light also will turn on when the parking brake is The odometer display shows the total distance the veapplied with the ignition switch in the ON/RUN posihicle has been driven. tion. U.S.
UNDERSTANDING YOUR INSTRUMENT PANEL 213 The two trip odometers show individual trip mileage. To switch from odometer to trip odometers, press and release the Trip Odometer button. To reset a trip odometer, display the desired trip odometer to be reset then push and hold the button until the display resets (approximately 2 seconds). Refer to “Trip Odometer Button” for additional information. CHANgE OIL . . . . . . . . . . . . . . Oil Change Required gASCAP . . . . . . . . . . . . . . . . . . . . . .
214 UNDERSTANDING YOUR INSTRUMENT PANEL HOTOIL the problem continues, the message will appear the next time the vehicle is started. See your authorized dealer service center as soon as possible. When this message is displayed there is a engine oil over-temperature condition. When this condition occurs, the “HOTOIL” message will be displayed in the odom- CHANgE OIL eter along with a chime.
UNDERSTANDING YOUR INSTRUMENT PANEL 215 the oil change indicator system (after performing the 15. Cruise Indicator — If Equipped scheduled maintenance) perform the following proceThis indicator shows that the Electronic Speed dure: Control System is ON. 1. Turn the ignition switch to the ON/RUN position (do 16. Odometer/Trip Odometer Reset Button not start the engine). Trip Odometer 2.
216 UNDERSTANDING YOUR INSTRUMENT PANEL 17. Electronic Throttle Control (ETC) Indicator Light 18. Park/Headlight ON Indicator — If Equipped This light informs you of a problem with the This indicator will illuminate when the park lights or headlights are turned on. Electronic Throttle Control (ETC) system. If a problem is detected, the light will come on while the engine is running. If the light remains 19.
UNDERSTANDING YOUR INSTRUMENT PANEL 217 21. Front Fog Light Indicator — If Equipped conventional brake system will continue to operate normally provided that the BRAKE warning light is not on. This indicator will illuminate when the front fog If the ABS light is on, the brake system should be serviced lights are on. as soon as possible to restore the benefit of Anti-Lock 22. Vehicle Security Light — If Equipped Brakes.
218 UNDERSTANDING YOUR INSTRUMENT PANEL • The ESC system will make buzzing or clicking running, a malfunction has been detected in the ESC system. If this light remains on after several ignition sounds when it is active. This is normal; the sounds will stop when ESC becomes inactive following the cycles, and the vehicle has been driven several miles maneuver that caused the ESC activation. (kilometers) at speeds greater than 30 mph (48 km/h), see your authorized dealer as soon as possible to have the 25.
UNDERSTANDING YOUR INSTRUMENT PANEL 219 Accordingly, when the low tire pressure telltale illuminates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure. Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability.
220 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! (Continued) equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equipment that is not of the same size, type, and/or style. Aftermarket wheels can cause sensor damage. Do not use tire sealant from a can or balance beads if your vehicle is equipped with a TPMS, as damage to the sensors may result. 26.
UNDERSTANDING YOUR INSTRUMENT PANEL 221 WARNING! CAUTION! A malfunctioning catalytic converter, as referenced above, can reach higher temperatures than in normal operating conditions. This can cause a fire if you drive slowly or park over flammable substances such as dry plants, wood, cardboard, etc. This could result in death or serious injury to the driver, occupants or others.
222 UNDERSTANDING YOUR INSTRUMENT PANEL 28. High Beam Indicator MINI-TRIP COMPUTER — IF EQUIPPED This light indicates that the headlights are on high The Mini-Trip Computer is located in the instrument beam. Pull the turn signal lever toward the steer- cluster and features a driver-interactive trip information and temperature display. ing wheel to switch the headlights to low beam. 29.
UNDERSTANDING YOUR INSTRUMENT PANEL 223 Control Buttons RESET Button To reset the display shown, turn the ignition switch to the ON position, then press and hold the RESET button located on the steering wheel. The following displays can be reset or changed: • Trip A • Trip B Trip Odometer (ODO) This display shows the distance traveled since the last reset. Press and release the STEP button on the instrument cluster to switch from odometer, to Trip A or Trip B.
224 UNDERSTANDING YOUR INSTRUMENT PANEL ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) — IF EQUIPPED The EVIC consists of the following: • Compass Heading Display (N, S, E, W, NE, NW, SE, SW) The Electronic Vehicle Information Center (EVIC) fea• Mileage (Avg/MPG) tures a driver-interactive display that is located in the instrument cluster.
UNDERSTANDING YOUR INSTRUMENT PANEL 225 The system allows the driver to select information by MENU Button pressing the following buttons on the instrument panel Press and release the MENU button to advance switch bank located below the climate controls: the display to each of the EVIC Main Menu features. Upon reaching the last item in the Main Menu the EVIC will advance to the first item in the Main Menu with the next MENU button press and release.
226 UNDERSTANDING YOUR INSTRUMENT PANEL SELECT Button • RKE (Remote Keyless Entry) Battery Low (with a single chime) Press and release the SELECT Button to accept a selection. The SELECT Button also resets • various Trip Functions.
UNDERSTANDING YOUR INSTRUMENT PANEL 227 • Remote start aborted — Hood ajar • Remote start aborted — Trunk ajar • Remote start aborted — Fuel low • Remote start disabled — System fault • Oil Change Required (with a single chime) • Low Tire (with a graphic of the car showing which tire(s) is/are low - with a single chime and ⬙Inflate to XX⬙). Refer to ⬙Tire Pressure Monitoring System⬙ in ⬙Starting and Operating⬙.
228 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: If the indicator message illuminates when you • Elapsed Time start the vehicle, the oil change indicator system did not • EVIC Units Selection reset. If necessary repeat this procedure. • System Status EVIC Main Menu To step to each main menu feature press and release the • Personal Settings MENU button once for each step. A step from the last item in the list will cause the first item in the feature list to be displayed.
UNDERSTANDING YOUR INSTRUMENT PANEL 229 Compass Display Automatic Compass Calibration COMPASS Button The compass heading indicates the direction the vehicle is facing. Press and release the compass button to display one of eight compass headings, the outside temperature, and audio information (if the radio is on) if the EVIC display is not already displaying this screen. This compass is self-calibrating, which eliminates the need to calibrate the compass manually.
230 UNDERSTANDING YOUR INSTRUMENT PANEL Manual Compass Calibration If the compass appears erratic or inaccurate, and the variance has been properly set, you may wish to manually recalibrate the compass. To manually calibrate the compass: 1. 2. 3. 4. Compass Variance Compass Variance is the difference between Magnetic North and Geographic North. To compensate for the differences, the variance should be set for the zone where the vehicle is driven, per the zone map.
UNDERSTANDING YOUR INSTRUMENT PANEL 231 3. Press and release the DOWN button until “Compass Variance” and the current Variance Value displays in the EVIC. 4. Press and release the SELECT button to increment the Variance Value by one, (one button press per update), until the proper variance zone is selected according to the map. NOTE: The Variance Values will wrap around from 15 back to 1. The Default Variance is Zone 8. Average Fuel Economy Shows the average fuel economy since the last reset.
232 UNDERSTANDING YOUR INSTRUMENT PANEL Distance To Empty (DTE) Tire PSI Shows the estimated distance that can be traveled with the fuel remaining in the tank. This estimated distance is determined by a weighted average of the instantaneous and average fuel economy, according to the current fuel tank level. DTE cannot be reset. Press and release the MENU button until ⬙Tire PSI⬙ is displayed.
UNDERSTANDING YOUR INSTRUMENT PANEL 233 Elapsed Time Pressure features. Press and Release the SELECT button to toggle units between ⬙U.S.⬙ and ⬙METRIC⬙. Shows the total elapsed time of travel since the last reset. Elapsed time will increment when the ignition switch is System Status in the RUN or START position. Displays SYSTEM OK if there are no active Warning Elapsed time is displayed as follows: Messages stored. Pressing and releasing the DOWN button when SYSTEM OK is displayed will do nothing.
234 UNDERSTANDING YOUR INSTRUMENT PANEL Press and release the MENU button until “Personal RKE Unlock Settings” displays in the EVIC. When “Driver Door 1st Press” is selected, only the Press and release the DOWN button to display the driver’s door will unlock on the first press of the Remote Keyless Entry (RKE) transmitter UNLOCK button.
UNDERSTANDING YOUR INSTRUMENT PANEL 235 headlights will also turn off when the wipers are turned off if they were turned on by this feature. To make your When ON is selected, the front and rear turn signals will selection, press the SELECT button until ON or OFF flash when the doors are locked or unlocked with the appears. RKE transmitter. This feature may be selected with or without the Sound Horn on lock feature selected.
236 UNDERSTANDING YOUR INSTRUMENT PANEL Illumin. Approach SETTING THE ANALOG CLOCK When this feature is selected, the headlights will activate and remain on for up to 90 seconds when the doors are unlocked with the remote keyless entry transmitter. To make your selection, press the SELECT button until “OFF,” “30 sec,” “60 sec,” or “90 sec” appears. To set the analog clock, located at the top center of the instrument panel, press and hold the button in until the setting is correct.
UNDERSTANDING YOUR INSTRUMENT PANEL 237 Uconnect® 730N/430/430N CD/DVD/HDD/NAV — IF EQUIPPED Uconnect® 130 Refer to your Uconnect® Supplement Manual for detailed operating instructions. Operating Instructions (Voice Command System) — If Equipped 4 Refer to “Voice Command” for further details. Operating Instructions (Uconnect® Phone) — If Equipped Refer to “Uconnect® Phone” for further details.
238 UNDERSTANDING YOUR INSTRUMENT PANEL Power Switch/Volume Control (Rotary) another selection. Holding either button will bypass stations without stopping, until you release it. Push the ON/VOLUME control knob to turn on the radio. Push the ON/VOLUME control knob a second TIME Button time to turn off the radio. Press the TIME button to alternate display of the time and radio frequency.
UNDERSTANDING YOUR INSTRUMENT PANEL 239 Push the rotary TUNE/SCROLL control knob a second time and MID will display. Turn the TUNE/SCROLL RW/FF control knob to the right or left to increase or decrease the Pressing the RW (Rewind) or FF (Fast Forward) buttons mid-range tones. causes the tuner to search for the next frequency in the Push the rotary TUNE/SCROLL control knob a third direction of the arrows. This feature operates in either time and TREBLE will display.
240 UNDERSTANDING YOUR INSTRUMENT PANEL Push the rotary TUNE/SCROLL control knob again to display window. Each button can be set for SET 1 and SET 2 in both AM and FM. This allows a total of 12 AM exit setting tone, balance, and fade. and 12 FM stations to be stored into pushbutton memory. AM/FM Button The stations stored in SET 2 memory can be selected by Press the buttons to select either AM or FM mode. pressing the pushbutton twice.
UNDERSTANDING YOUR INSTRUMENT PANEL 241 If you insert a disc with the ignition ON and the radio ON, the unit will switch from radio to CD mode and begin to play when you insert the disc. The display will NOTE: show the track number, and index time in minutes and • The ignition switch must be in the ON or ACC position seconds. Play will begin at the start of track 1. to operate the radio.
242 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! (Continued) • Dual-media disc types (one side is a DVD, the other side is a CD) should not be used, and they can cause damage to the player. EJECT Button — Ejecting A CD Press the EJECT button to eject the CD. SEEK Button Press the right SEEK button for the next selection on the CD.
UNDERSTANDING YOUR INSTRUMENT PANEL 243 AM/FM Button Supported Media (Disc Types) Press the button to select either AM or FM mode. The MP3 file recording media supported by the radio are CDDA, CD-R, CD-RW, MP3, and CDDA+MP3. SET/RND Button (Random Play Button) Supported Medium Formats (File Systems) Press this button while the CD is playing to activate Random Play.
244 UNDERSTANDING YOUR INSTRUMENT PANEL display the file name and folder name, and will assign a number instead. With a maximum number of files, exceeding 20 folders will result in this display. With 200 files, exceeding 50 folders will result in this display.) • Maximum number of characters in file/folder names: • Level 1: 12 (including a separator ⬙.⬙ and a threecharacter extension) • Level 2: 31 (including a separator ⬙.
UNDERSTANDING YOUR INSTRUMENT PANEL 245 MPEG Specification MPEG-1 Audio Layer 3 Sampling Frequency (kHz) 48, 44.1, 32 MPEG-2 Audio Layer 3 24, 22.05, 16 Bit Rate (kbps) 320, 256, 224, 192, 160, 128, 112, 96, 80, 64, 56, 48, 40, 32 160, 128, 144, 112, 96, 80, 64, 56, 48, 40, 32, 24, 16, 8 Playback Of MP3 Files When a medium containing MP3 data is loaded, the radio checks all files on the medium.
246 UNDERSTANDING YOUR INSTRUMENT PANEL To increase the speed of disc loading, it is recommended Pressing the DISC/AUX button will change the mode to to use CD-R media and single-session discs. To create a auxiliary device if the AUX jack is connected. single-session disc, enable the “Disc at Once” option NOTE: The AUX device must be turned on and the before writing to the disc. device’s volume set to proper level. If the AUX audio is not loud enough, turn the device’s volume up.
UNDERSTANDING YOUR INSTRUMENT PANEL 247 Uconnect® 130 WITH SATELLITE RADIO Power Switch/Volume Control (Rotary) Push the ON/VOLUME control knob to turn on the radio. Push the ON/VOLUME control knob a second time to turn off the radio. Electronic Volume Control The electronic volume control turns continuously (360 degrees) in either direction, without stopping. Turning the ON/VOLUME control knob to the right increases the volume, and to the left decreases it.
248 UNDERSTANDING YOUR INSTRUMENT PANEL another selection. Holding either button will bypass Phone Button Uconnect® Phone — If Equipped stations without stopping, until you release it. Press this button to operate the Uconnect® Phone feature (if equipped). Refer to “Uconnect® Phone” in “UnderVoice Command System (Radio) — If Equipped standing The Features Of Your Vehicle”. Refer to “Voice Command” in “Understanding The Features Of Your Vehicle”.
UNDERSTANDING YOUR INSTRUMENT PANEL 249 3. After adjusting the hours, press the right side TUNE/ INFO Button SCROLL control knob to set the minutes. The minutes Press the INFO button for an RDS station (one with call will begin to blink. letters displayed). The radio will return a Radio Text 4. Adjust the minutes using the right side TUNE/ message broadcast from an FM station (FM mode only). SCROLL control knob. Press the TUNE/SCROLL con- RW/FF trol knob to save time change.
250 UNDERSTANDING YOUR INSTRUMENT PANEL Push the rotary TUNE/SCROLL control knob a second Push the rotary TUNE/SCROLL control knob again to time and MID will display. Turn the TUNE/SCROLL exit setting tone, balance, and fade. control knob to the right or left to increase or decrease the MUSIC TYPE Button mid-range tones. Pressing this button once will turn on the Music Type Push the rotary TUNE/SCROLL control knob a third mode for five seconds. Pressing the MUSIC TYPE button time and TREBLE will display.
UNDERSTANDING YOUR INSTRUMENT PANEL 251 Program Type Classical Classic Rock College Country Foreign Language Information Jazz News Nostalgia Oldies Personality Public Rhythm and Blues Religious Music 16-Digit Character Display Classicl Cls Rock College Country Language Inform Jazz News Nostalga Oldies Persnlty Public R&B Rel Musc Program Type Religious Talk Rock Soft Soft Rock Soft Rhythm and Blues Sports Talk Top 40 Weather 16-Digit Character Display Rel Talk Rock Soft Soft Rck Soft R&B Sports Talk Top
252 UNDERSTANDING YOUR INSTRUMENT PANEL If a preset button is activated while in the Music Type SET/RND Button — To Set The Pushbutton (Program Type) mode, the Music Type mode will be Memory exited and the radio will tune to the preset station. When you are receiving a station that you wish to commit to pushbutton memory, press the SET/RND SETUP Button button. The symbol SET 1 will now show in the display Pressing the SETUP button allows you to select between window.
UNDERSTANDING YOUR INSTRUMENT PANEL 253 Every time a preset button is used, a corresponding • This radio is capable of playing compact discs (CD), recordable compact discs (CD-R), rewritable compact button number will display. discs (CD-RW), compact discs with MP3 tracks and Buttons 1 - 6 multisession compact discs with CD and MP3 tracks.
254 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! • This CD player will accept 4–3/4 in (12 cm) discs only. The use of other sized discs may damage the CD player mechanism. • Do not use adhesive labels. These labels can peel away and jam the player mechanism. • The Uconnect® 130 is a single CD player. Do not attempt to insert a second CD if one is already loaded. • Dual-media disc types (one side is a DVD, the other side is a CD) should not be used, and they can cause damage to the player.
UNDERSTANDING YOUR INSTRUMENT PANEL 255 RW/FF Notes On Playing MP3 Files Press and hold FF (Fast Forward) and the CD player will begin to fast forward until FF is released or RW or another CD button is pressed. The RW (Reverse) button works in a similar manner. The radio can play MP3 files; however, acceptable MP3 file recording media and formats are limited. When writing MP3 files, pay attention to the following restrictions. AM/FM Button Press the button to select either AM or FM mode.
256 UNDERSTANDING YOUR INSTRUMENT PANEL Multisession disc formats are supported by the radio. Multisession discs may contain combinations of normal • Maximum number of folder levels: 8 CD audio tracks and computer files (including MP3 files). Discs created with an option such as ⬙keep disc open after • Maximum number of files: 255 writing⬙ are most likely multisession discs. The use of • Maximum number of folders.
UNDERSTANDING YOUR INSTRUMENT PANEL 257 use a 44.1 kHz sampling rate and a 192, 160, 128, 96 or VBR bit rates. MPEG Specification MPEG-1 Audio Layer 3 MPEG-2 Audio Layer 3 Sampling Frequency (kHz) 48, 44.1, 32 24, 22.05, 16 Bit Rate (kbps) 320, 256, 224, 192, 160, 128, 112, 96, 80, 64, 56, 48, 40, 32 160, 128, 144, 112, 96, 80, 64, 56, 48, 40, 32, 24, 16, 8 ID3 Tag information for artist, song title, and album title are supported for version 1 ID3 tags. ID3 version 2 is not supported by the radios.
258 UNDERSTANDING YOUR INSTRUMENT PANEL To increase the speed of disc loading, it is recommended to use CD-R media and single-session discs. To create a single-session disc, enable the “Disc at Once” option before writing to the disc. Press the INFO button once more to return to ⬙elapsed time⬙ priority mode. LIST Button — CD Mode For MP3 Play Press and hold the INFO button again for three seconds to return to ⬙elapsed time⬙ display.
UNDERSTANDING YOUR INSTRUMENT PANEL 259 NOTE: The AUX device must be turned on and the device’s volume set to the proper level. If the AUX audio is not loud enough, turn the device’s volume up. If the AUX audio sounds distorted, turn the device’s volume down. NOTE: Sirius service is not available in Hawaii and has limited coverage in Alaska.
260 UNDERSTANDING YOUR INSTRUMENT PANEL Electronic Serial Number/Sirius Identification Number (ESN/SID) Selecting Uconnect® (Satellite) Mode Press the SAT button until ⬙SAT⬙ appears in the display. A Please have the following information available when CD may remain in the radio while in the Satellite radio calling: mode. 1. The Electronic Serial Number/Sirius Identification Satellite Antenna Number (ESN/SID).
UNDERSTANDING YOUR INSTRUMENT PANEL 261 • Dense tree coverage may interrupt reception in the SCAN Button form of short audio mutes. Pressing the SCAN button causes the tuner to search for • Driving under wide bridges or along tall buildings can the next channel, pausing for eight seconds before continuing to the next. To stop the search, press the SCAN cause intermittent reception. button a second time. • Placing objects over or too close to the antenna can INFO Button cause signal blockage.
262 UNDERSTANDING YOUR INSTRUMENT PANEL TUNE Control (Rotary) SETUP Button Turn the rotary TUNE/SCROLL control knob clockwise Pressing the SETUP button allows you to select the to increase or counterclockwise to decrease the channel. following items: • Display Sirius ID number — Press the AUDIO/ SELECT button to display the Sirius ID number. This Pressing this button once will turn on the Music Type number is used to activate, deactivate, or change the mode for five seconds.
UNDERSTANDING YOUR INSTRUMENT PANEL 263 You may add a second channel to each pushbutton by repeating the above procedure with this exception: Press the SET button twice and SET 2 will show in the display window. Each button can be set for SET 1 and SET 2. This allows a total of 12 Satellite channels to be stored into pushbutton memory. The channels stored in SET 2 memory can be selected by pressing the pushbutton twice.
264 UNDERSTANDING YOUR INSTRUMENT PANEL Once the audio device is connected and synchronized to Use the connection cable to connect an iPod® or external the vehicle’s iPod®/USB/MP3 control system (iPod® or USB device to the vehicle’s USB connector port which is external USB device may take a few minutes to connect), the audio device starts charging and is ready for use by located in the center of the instrument panel below the pressing radio switches, as described below. climate controls.
UNDERSTANDING YOUR INSTRUMENT PANEL 265 • The audio device can be controlled using the radio mode. In Play mode, the following buttons on the radio buttons to Play, Browse, and List the iPod® contents. faceplate may be used to control the iPod® or external USB device and display data: • The audio device battery charges when plugged into the USB/AUX connector (if supported by the specific • Use the TUNE control knob to select the next or previous track. audio device).
266 UNDERSTANDING YOUR INSTRUMENT PANEL • A single press backward << RW or forward FF>> will • Press the SCAN button to use iPod®/USB/MP3 dejump backward or forward respectively, for five secvice scan mode, which will play the first ten seconds of each track in the current list and then forward to the onds. next song. To stop SCAN mode and start playing the • Use the << SEEK and SEEK >> buttons to jump to the desired track, when it is playing the track, press the previous or next track.
UNDERSTANDING YOUR INSTRUMENT PANEL 267 • During all List modes, the iPod® displays all lists in “wrap-around” mode. So if the track is at the bottom of During Play mode, pressing any of the buttons described the list, just turn the wheel backward (counterclockbelow, will bring up List mode. List mode enables wise) to get to the track faster. scrolling through the list of menus and tracks on the audio device.
268 UNDERSTANDING YOUR INSTRUMENT PANEL • Pressing a PRESET button will display the current list on the top line and the first item in that list on the second line. • To exit List mode without selecting a track, press the same PRESET button again to go back to Play mode. • LIST button: The LIST button will display the top level menu of the iPod® or external USB device. • Turn the TUNE control knob to list the top-menu item to be selected and press the TUNE control knob.
UNDERSTANDING YOUR INSTRUMENT PANEL 269 Bluetooth® Streaming Audio (BTSA) Selecting A Different Audio Device Music can be streamed from your cellular phone to the 1. Press the PHONE button to begin. Uconnect® phone system. 2. After the ⬙Ready⬙ prompt and following the beep, say Controlling BTSA Using Radio Buttons ⬙Setup⬙, then say ⬙Select Audio Devices.⬙ To enter BTSA mode, press either “AUX” button on the 3.
270 UNDERSTANDING YOUR INSTRUMENT PANEL Previous Track STEERING WHEEL AUDIO CONTROLS — IF Use the SEEK DOWN button, or press the VR button on EQUIPPED the radio and say “Previous Track,” to jump to the previous music track on your cellular phone. Browse Browsing is not available on a Bluetooth® Streaming Audio (BTSA) device. Only the current song that is playing will display info.
UNDERSTANDING YOUR INSTRUMENT PANEL 271 The remote sound system controls are located on the rear Radio Operation surface of the steering wheel, at the three and nine Pressing the top of the switch will SEEK up for the next o’clock positions. listenable station, and pressing the bottom of the switch The right-hand rocker switch has a pushbutton in the will SEEK down for the next listenable station.
272 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: If you experience difficulty in playing a particular To keep a CD/DVD in good condition, take the following disc, it may be damaged (e.g., scratched, reflective coating removed, a hair, moisture or dew on the disc) precautions: oversized, or have protection encoding. Try a known 1. Handle the disc by its edge; avoid touching the good disc before considering disc player service. surface. RADIO OPERATION AND MOBILE PHONES 2.
UNDERSTANDING YOUR INSTRUMENT PANEL 273 The Manual Temperature Controls consist of a series of The air conditioning and heating system is designed to outer rotary dials and inner push knobs. make you comfortable in all types of weather. Blower Control CLIMATE CONTROLS Manual Heating And Air Conditioning Rotate this control to regulate the amount of air forced through the ventilation system in any mode. The blower speed increases as you move the control to the right from the “O” (OFF) position.
274 UNDERSTANDING YOUR INSTRUMENT PANEL Temperature Control Rotate this control to regulate the temperature of the air inside the passenger compartment. Rotating the dial left into the blue area of the scale indicates cooler temperatures, while rotating right into the red area indicates warmer temperatures. NOTE: If your air conditioning performance seems lower than expected, check the front of the A/C condenser located in front of the radiator for an accumulation of dirt or insects.
UNDERSTANDING YOUR INSTRUMENT PANEL 275 • ECONOMY MODE • Panel Air is directed through the outlets in the instruIf economy mode is desired, press the A/C button to turn ment panel. These outlets can be adjusted to direct OFF the indicator light and the A/C compressor. Then, select Panel, Bi-Level or Floor mode and move the airflow. temperature control to the desired temperature.
276 UNDERSTANDING YOUR INSTRUMENT PANEL • Floor NOTE: The air conditioning compressor operates in Mix, Defrost, or a blend of these modes, even if the Air Air is directed through the floor outlets with a Conditioning (A/C) button is not pressed. This dehusmall amount flowing through the defrost and midifies the air to help dry the windshield. To improve side window demist outlets. fuel economy, use these modes only when necessary.
UNDERSTANDING YOUR INSTRUMENT PANEL 277 • The use of the Recirculation mode in cold or damp Automatic Temperature Control (ATC) — If weather will cause windows to fog on the inside, Equipped because of moisture buildup inside the vehicle. Select the outside air position for maximum defogging. • The A/C will engage automatically to prevent fogging when the recirculation button is pressed and the mode control is set to panel or Bi-Level. 4 • Recirculated air is not allowed in Defrost modes.
278 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: The AUTO position performs best for front seat The Automatic Temperature Control system automati- occupants only. cally maintains the climate in the cabin of the vehicle at 2. Dial in the temperature you would the comfort levels desired by the driver and passenger. like the system to maintain by rotating the Temperature Control knob. Once the Operation of the system is quite simple.
UNDERSTANDING YOUR INSTRUMENT PANEL 279 NOTE: Manual Operation • The temperature setting can be adjusted at anytime This system offers a full complement of manual override features, which consist of Blower Preferred Automatic, without affecting automatic operation. Mode Preferred Automatic, or Blower and Mode Pre• Pressing the Air Conditioning Control button while in ferred Automatic. This means the operator can override AUTO mode will cause the LED in the control button the blower, the mode, or both.
280 UNDERSTANDING YOUR INSTRUMENT PANEL
UNDERSTANDING YOUR INSTRUMENT PANEL 281 The operator can override the AUTO mode setting to • Floor change airflow distribution by rotating the Mode Control Air is directed through the floor outlets with a knob (on the right) to one of the following positions. small amount flowing through the defrost and • Panel side window demist outlets. Air is directed through the outlets in the instrument • Mix panel. These outlets can be adjusted to direct airflow.
282 UNDERSTANDING YOUR INSTRUMENT PANEL • Air Conditioner Control NOTE: Press this button to turn on the air • When the ignition switch is turned to the LOCK position, the recirculation feature will be cancelled. conditioning during manual operation only. When the air conditioning is • In cold weather, use of the Recirculation mode may turned on, cool dehumidified air will lead to excessive window fogging.
UNDERSTANDING YOUR INSTRUMENT PANEL 283 • Most of the time, when in Automatic Operation, you can temporarily put the system into Recirculation Mode by pressing the Recirculation button. However, under certain conditions, while in Automatic Mode, the system is blowing air out the defrost vents. When these conditions are present, and the Recirculation button is pressed, the indicator will flash and then turn off. This tells you that you are unable to go into Recirculation Mode at this time.
284 UNDERSTANDING YOUR INSTRUMENT PANEL coolant that meets the requirements of Chrysler Material Standard MS-12106 and 50% water is recommended. Refer to “Maintenance Procedures” in “Maintaining Your Vehicle” for proper coolant selection. Window Fogging Interior fogging on the windshield can be quickly removed by turning the mode selector to Defrost. The Mix mode can be used to maintain a clear windshield and provide sufficient heating.
UNDERSTANDING YOUR INSTRUMENT PANEL 285 Outside Air Intake A/C Air Filter — If Equipped Make sure the air intake, located directly in front of the windshield, is free of obstructions such as leaves. Leaves collected in the air intake may reduce airflow, and if they enter the plenum, they could plug the water drains. In winter months, make sure the air intake is clear of ice, slush, and snow. The A/C Filter prevents most dust and pollen from entering the cabin.
286 UNDERSTANDING YOUR INSTRUMENT PANEL Control Setting Suggestions For Various Weather Conditions
STARTING AND OPERATING CONTENTS 䡵 STARTING PROCEDURES . . . . . . . . . . . . . . . .291 ▫ Brake/Transmission Shift Interlock System . . .298 ▫ Automatic Transmission . . . . . . . . . . . . . . . .291 ▫ Four-Speed Automatic Transmission — If Equipped. . . . . . . . . . . . . . . . . . . . . . . . . .298 ▫ Normal Starting. . . . . . . . . . . . . . . . . . . . . . .292 ▫ Extreme Cold Weather (Below –20°F Or −29°C) . . . . . . . . . . . . . . . .293 ▫ If Engine Fails To Start . . . . . . . . . . . . . .
288 STARTING AND OPERATING 䡵 DRIVING THROUGH WATER . . . . . . . . . . . . .317 ▫ Flowing/Rising Water . . . . . . . . . . . . . . . . . .317 ▫ Shallow Standing Water . . . . . . . . . . . . . . . . .317 䡵 POWER STEERING . . . . . . . . . . . . . . . . . . . . .319 ▫ Power Steering Fluid Check . . . . . . . . . . . . . .319 䡵 PARKING BRAKE . . . . . . . . . . . . . . . . . . . . . .320 䡵 ANTI-LOCK BRAKE SYSTEM (ABS) . . . . . . . . .322 䡵 ELECTRONIC BRAKE CONTROL SYSTEM . . . .
STARTING AND OPERATING 289 ▫ Run Flat Tires — If Equipped . . . . . . . . . . . . .347 ▫ Reformulated Gasoline . . . . . . . . . . . . . . . . .364 ▫ Spare Tires — If Equipped . . . . . . . . . . . . . . .348 ▫ Gasoline/Oxygenate Blends . . . . . . . . . . . . . .365 ▫ Tire Spinning . . . . . . . . . . . . . . . . . . . . . . . .350 ▫ E-85 Usage In Non-Flex Fuel Vehicles . . . . . . .365 ▫ Tread Wear Indicators . . . . . . . . . . . . . . . . . .350 ▫ MMT In Gasoline . . . . . . . . . . . . . . . .
290 STARTING AND OPERATING ▫ Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . .371 䡵 TRAILER TOWING . . . . . . . . . . . . . . . . . . . . .376 ▫ Cruising Range . . . . . . . . . . . . . . . . . . . . . . .371 ▫ Common Towing Definitions . . . . . . . . . . . . .377 ▫ Replacement Parts . . . . . . . . . . . . . . . . . . . .371 ▫ Trailer Hitch Classification . . . . . . . . . . . . . . .379 ▫ Maintenance . . . . . . . . . . . . . . . . . . . . . . . .
STARTING AND OPERATING 291 STARTING PROCEDURES WARNING! (Continued) Before starting your vehicle, adjust your seat, adjust the inside and outside mirrors, fasten your seat belt, and if present, instruct all other occupants to buckle their seat belts. WARNING! • Do not leave the key fob in or near the vehicle, or in a location accessible to children. A child could operate power windows, other controls, or move the vehicle.
292 STARTING AND OPERATING CAUTION! Damage to the transmission may occur if the following precautions are not observed: • Do not shift from REVERSE, PARK, or NEUTRAL into any forward gear when the engine is above idle speed. • Shift into PARK only after the vehicle has come to a complete stop. • Shift into or out of REVERSE only after the vehicle has come to a complete stop and the engine is at idle speed. • Before shifting into any gear, make sure your foot is firmly on the brake pedal.
STARTING AND OPERATING 293 Extreme Cold Weather (Below –20°F Or −29°C) To ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (available from your authorized dealer) is recommended. If Engine Fails To Start WARNING! • Never pour fuel or other flammable liquid into the throttle body air inlet opening in an attempt to start the vehicle. This could result in flash fire causing serious personal injury.
294 STARTING AND OPERATING the way to the floor and hold it there while cranking the With Tip Start engine. This should clear any excess fuel in case the If the engine fails to start after you have followed the engine is flooded. “Normal Starting” or “Extreme Cold Weather” procedures, it may be flooded. To clear any excess fuel, push CAUTION! the accelerator pedal all the way to the floor and hold it.
STARTING AND OPERATING 295 After Starting The idle speed is controlled automatically and it will decrease as the engine warms up. ENGINE BLOCK HEATER — IF EQUIPPED WARNING! Remember to disconnect the engine block heater cord before driving. Damage to the 110-115 Volt electrical cord could cause electrocution. The engine block heater warms the engine, and permits AUTOMATIC TRANSMISSION quicker starts in cold weather.
296 STARTING AND OPERATING CAUTION! (Continued) WARNING! • Do not shift between PARK, REVERSE, NEUTRAL, or DRIVE when the engine is above idle speed. • Before shifting into any gear, make sure your foot is firmly pressing the brake pedal. • It is dangerous to shift out of PARK or NEUTRAL if the engine speed is higher than idle speed. If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in reverse.
STARTING AND OPERATING 297 WARNING! (Continued) WARNING! (Continued) • Unintended movement of a vehicle could injure those in and near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, always apply the parking brake, shift the transmission into PARK, turn the engine OFF, and remove the ignition key. Once the key is removed, the transmission is locked in PARK, securing the vehicle against unwanted movement.
298 STARTING AND OPERATING when the ignition is in the LOCK position, and once Four-Speed Automatic Transmission — If removed, the transmission is locked in PARK. Equipped NOTE: If a malfunction occurs, the system will trap the key in the ignition switch to warn you that this safety feature is inoperable. The engine can be started and stopped but the key cannot be removed until you obtain service.
STARTING AND OPERATING 299 the transmission locking mechanism may make it difficult to move the shift lever out of PARK. As an added DO NOT race the engine when shifting from PARK or precaution, turn the front wheels toward the curb on a NEUTRAL into another gear range. downhill grade and away from the curb on an uphill NOTE: After selecting any gear range, wait a moment to grade. allow the selected gear to engage before accelerating. This is especially important when the engine is cold.
300 STARTING AND OPERATING WARNING! (Continued) WARNING! (Continued) • It is dangerous to shift out of PARK or NEUTRAL if the engine speed is higher than idle speed. If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in reverse. You could lose control of the vehicle and hit someone or something. Only shift into gear when the engine is idling normally and your foot is firmly pressing the brake pedal.
STARTING AND OPERATING 301 WARNING! (Continued) CAUTION! • When leaving the vehicle, always remove the ignition key and lock your vehicle. Never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking brake, brake pedal or the shift lever.
302 STARTING AND OPERATING • Look at the transmission gear position display and verify that it indicates the PARK position. • With brake pedal released, verify that the shift lever will not move out of PARK. REVERSE (R) This range is for moving the vehicle backward. Shift into REVERSE only after the vehicle has come to a complete stop. NEUTRAL (N) Use this range when the vehicle is standing for prolonged periods with the engine running. The engine may be started in this range.
STARTING AND OPERATING 303 DRIVE (D) This range should be used for most city and highway driving. It provides the smoothest upshifts and downshifts, and the best fuel economy. The transmission automatically upshifts through all forward gears. The DRIVE position provides optimum driving characteristics under all normal operating conditions. During cold temperatures, transmission operation may be modified depending on engine and transmission temperature as well as vehicle speed.
304 STARTING AND OPERATING will improve performance and extend transmission life by reducing excessive shifting and heat build-up. The ⬙3⬙ range should also be used when descending steep grades to avoid brake system distress. LOW (L) PARK, REVERSE, and NEUTRAL will continue to operate. The Malfunction Indicator Light (MIL) may be illuminated. Limp Home Mode allows the vehicle to be driven to an authorized dealer for service without damaging the transmission.
STARTING AND OPERATING 305 NOTE: Even if the transmission can be reset, we recom- • The engine coolant has reached an adequate temperamend that you visit your authorized dealer at your ture. earliest possible convenience. Your authorized dealer has • Vehicle speed is sufficiently high. diagnostic equipment to determine if the problem could recur. • The driver is not heavily pressing the accelerator. If the transmission cannot be reset, authorized dealer Torque Converter Clutch service is required.
306 STARTING AND OPERATING NOTE: The torque converter clutch will not engage until the transmission fluid and engine coolant are warm [usually after 1 to 3 miles (2 to 5 km) of driving]. Because the engine speed is higher when the torque converter clutch is not engaged, it may seem as if the transmission is not shifting into Overdrive when cold. This is normal.
STARTING AND OPERATING 307 NOTE: After selecting any gear range, wait a moment to allow the selected gear to engage before accelerating. This is especially important when the engine is cold. PARK (P) This range supplements the parking brake by locking the transmission. The engine can be started in this range. Never attempt to use PARK while the vehicle is in motion. Apply the parking brake when leaving the vehicle in this range.
308 STARTING AND OPERATING downhill grade and away from the curb on an uphill grade. WARNING! • Never use the PARK position as a substitute for the parking brake. Always apply the parking brake fully when parked to guard against vehicle movement and possible injury or damage. • Your vehicle could move and injure you and others if it is not completely in PARK. Check by trying to move the shift lever out of PARK with the brake pedal released. Make sure the transmission is in PARK before leaving the vehicle.
STARTING AND OPERATING 309 WARNING! (Continued) WARNING! (Continued) • Unintended movement of a vehicle could injure those in or near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, always apply the parking brake, shift the transmission into PARK, turn the engine OFF, and remove the ignition key. Once the key is removed, the transmission is locked in PARK, securing the vehicle against unwanted movement.
310 STARTING AND OPERATING CAUTION! • Before moving the shift lever out of PARK, you must turn the ignition switch from the LOCK/OFF position to the ON/RUN position, and also press the brake pedal. Otherwise, damage to the shift lever could result. • DO NOT race the engine when shifting from PARK or NEUTRAL into another gear range, as this can damage the drivetrain. • Look at the transmission gear position display and verify that it indicates the PARK position.
STARTING AND OPERATING 311 WARNING! Do not coast in NEUTRAL and never turn off the ignition to coast down a hill. These are unsafe practices that limit your response to changing traffic or road conditions. You might lose control of the vehicle and have a collision. CAUTION! Towing the vehicle, coasting, or driving for any other reason with the transmission in NEUTRAL can cause severe transmission damage.
312 STARTING AND OPERATING temperature as well as vehicle speed. This feature improves warm up time of the engine and transmission to achieve maximum efficiency. Engagement of the torque converter clutch is inhibited until the transmission fluid is warm (refer to the “Note” under “Torque Converter Clutch” in this section). During extremely cold temperatures (-16°F [-27°C] or below), operation may briefly be limited to third gear only.
STARTING AND OPERATING 313 NOTE: Even if the transmission can be reset, we recom- • The engine coolant has reached an adequate temperamend that you visit your authorized dealer at your ture. earliest possible convenience. Your authorized dealer has • The vehicle speed is sufficiently high. diagnostic equipment to determine if the problem could recur. • The driver is not heavily pressing the accelerator. If the transmission cannot be reset, authorized dealer Torque Converter Clutch service is required.
314 STARTING AND OPERATING NOTE: The torque converter clutch will not engage until the transmission fluid and engine coolant are warm (usually after 1 to 3 miles [2 to 5 km] of driving). Because the engine speed is higher when the torque converter clutch is not engaged, it may seem as if the transmission is not shifting into Overdrive when cold. This is normal.
STARTING AND OPERATING 315 • You can start out, from a stop, in any gear except top • If the system detects a problem, it will disable gear. Tapping (+) (at a stop) will allow starting in AutoStick® mode and the transmission will return to automatic mode until the problem is corrected. second gear. Starting out in second gear is helpful in snowy or icy conditions. To disengage AutoStick® mode, return the shift lever to • The transmission will automatically upshift when nec- the DRIVE position.
316 STARTING AND OPERATING DRIVING ON SLIPPERY SURFACES Traction Acceleration When driving on wet or slushy roads, it is possible for a wedge of water to build up between the tire and road surface. This is hydroplaning and may cause partial or complete loss of vehicle control and stopping ability.
STARTING AND OPERATING 317 DRIVING THROUGH WATER Shallow Standing Water Driving through water more than a few inches/ Although your vehicle is capable of driving through centimeters deep will require extra caution to ensure shallow standing water, consider the following Cautions safety and prevent damage to your vehicle. and Warnings before doing so. Flowing/Rising Water WARNING! Do not drive on or across a road or path where water is flowing and/or rising (as in storm run-off).
318 STARTING AND OPERATING CAUTION! CAUTION! (Continued) • Always check the depth of the standing water before driving through it. Never drive through standing water that is deeper than the bottom of the tire rims mounted on the vehicle. • Determine the condition of the road or the path that is under water and if there are any obstacles in the way before driving through the standing water. • Do not exceed 5 mph (8 km/h) when driving through standing water. This will minimize wave effects.
STARTING AND OPERATING 319 POWER STEERING The standard power steering system will give you good vehicle response and increased ease of maneuverability in tight spaces. The system will provide mechanical steering capability if power assist is lost. If for some reason the power assist is interrupted, it will still be possible to steer your vehicle. Under these conditions, you will observe a substantial increase in steering effort, especially at very low vehicle speeds and during parking maneuvers.
320 STARTING AND OPERATING CAUTION! Do not use chemical flushes in your power steering system as the chemicals can damage your power steering components. Such damage is not covered by the New Vehicle Limited Warranty. PARKING BRAKE Before leaving the vehicle, make sure that the parking brake is fully applied. Also, be certain to leave the transmission in PARK.
STARTING AND OPERATING 321 possible. To release the parking brake, pull the lever up brake before placing the shift lever in PARK, otherwise slightly, press the center button, then lower the lever the load on the transmission locking mechanism may completely. make it difficult to move the shift lever out of PARK. The parking brake should always be applied whenever the When the parking brake is applied with the ignition driver is not in the vehicle.
322 STARTING AND OPERATING WARNING! (Continued) WARNING! (Continued) • Never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking brake, brake pedal or the shift lever. • Do not leave the Key Fob in or near the vehicle, or in a location accessible to children.
STARTING AND OPERATING 323 computer to modulate the hydraulic pressure to prevent wheel lock-up and avoid skidding on slippery surfaces. WARNING! • Pumping of the anti-lock brakes will diminish their effectiveness and may lead to a collision. Pumping makes the stopping distance longer. Just press firmly on your brake pedal when you need to slow down or stop.
324 STARTING AND OPERATING If the “Anti-Lock Brake Warning Light” is on, the brake system should be serviced as soon as possible to restore the benefits of anti-lock brakes. If the “Anti-Lock Brake Warning Light” does not come on when the ignition switch is turned to the ON position, have the bulb repaired as soon as possible. ABS is activated during braking under certain road or stopping conditions.
STARTING AND OPERATING 325 WARNING! The Anti-Lock Brake System contains sophisticated electronic equipment that may be susceptible to interference caused by improperly installed or high output radio transmitting equipment. This interference can cause possible loss of anti-lock braking capability. Installation of such equipment should be performed by qualified professionals.
326 STARTING AND OPERATING WARNING! (Continued) very slippery surfaces, or hydroplaning. The capabilities of an ABS-equipped vehicle must never be exploited in a reckless or dangerous manner which could jeopardize the user’s safety or the safety of others. Traction Control System (TCS) This system monitors the amount of wheel spin of each of the driven wheels.
STARTING AND OPERATING 327 WARNING! • The BAS cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded. • The BAS cannot prevent collisions, including those resulting from excessive speed in turns, following another vehicle too closely, or hydroplaning.
328 STARTING AND OPERATING WARNING! Electronic Stability Control (ESC) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. ESC cannot prevent accidents, including those resulting from excessive speed in turns, driving on very slippery surfaces, or hydroplaning. ESC also cannot prevent accidents resulting from loss of vehicle control due to inappropriate driver input for the conditions.
STARTING AND OPERATING 329 intended to be used if the vehicle is in deep snow, sand, To turn ESC on again, momentarily press the “ESC Off” or gravel conditions and more wheel spin than ESC switch. This will restore the normal “ESC On” mode of would normally allow is required to gain traction. operation. WARNING! When in “Partial Off” mode, the TCS functionality of ESC (except for the limited slip feature described in the TCS section) has been disabled and the “ESC Off Indicator Light” will be illuminated.
330 STARTING AND OPERATING NOTE: To improve the vehicle’s traction when driving with snow chains, or starting off in deep snow, sand or gravel, it may be desirable to switch to the “Partial Off” mode by pressing the “ESC Off” switch. Once the situation requiring ESC to be switched to the “Partial Off” mode is overcome, turn ESC on again by momentarily pressing the “ESC Off” switch. This may be done while the vehicle is in motion.
STARTING AND OPERATING 331 • Each time the ignition is cycled ON, the ESC system TIRE SAFETY INFORMATION Tire Markings will be ON even if it was cycled off previously. • The ESC system will make buzzing or clicking sounds when it is active. This is normal; the sounds will stop when ESC becomes inactive following the maneuver that caused the ESC activation. The “ESC OFF Indicator Light” indicates the Electronic Stability Control (ESC) is partially off. 5 1 — U.S.
332 STARTING AND OPERATING • LT (Light Truck) - Metric tire sizing is based on U.S. design standards. The size designation for LT-Metric • P (Passenger) - Metric tire sizing is based on U.S. tires is the same as for P-Metric tires except for the design standards. P-Metric tires have the letter “P” letters “LT” that are molded into the sidewall precedmolded into the sidewall preceding the size designaing the size designation. Example: LT235/85R16. tion. Example: P215/65R15 95H.
STARTING AND OPERATING 333 Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ⴖ....blank....ⴖ = Passenger car tire based on European design standards LT = Light truck tire based on U.S. design standards T or S = Temporary spare tire 31 = Overall diameter in inches (in) 215 = Section width in millimeters (mm) 65 = Aspect ratio in percent (%) — Ratio of section height to section width of tire 10.
334 STARTING AND OPERATING EXAMPLE: Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions — The maximum speed corresponding to the speed symbol should only be achieved under specified operating conditions (i.e.
STARTING AND OPERATING 335 Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full TIN, including the date code, located on the white sidewall side of the tire. Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the outboard side, then you will find it on the inboard side of the tire.
336 STARTING AND OPERATING Tire Terminology And Definitions Term B-Pillar Cold Tire Inflation Pressure Maximum Inflation Pressure Recommended Cold Tire Inflation Pressure Tire Placard Definition The vehicle B-Pillar is the structural member of the body located behind the front door. Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least three hours, or driven less than 1 mile (1.6 km) after sitting for a three hour period.
STARTING AND OPERATING 337 Tire Loading And Tire Pressure Tire And Loading Information Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar or the rear edge of the driver’s side door.
338 STARTING AND OPERATING Tire And Loading Information Placard 3. Tire size designed for your vehicle. 4. Cold tire inflation pressures for the front, rear, and spare tires. Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle.
STARTING AND OPERATING 339 To determine the maximum loading conditions of your 4. The resulting figure equals the available amount of vehicle, locate the statement “The combined weight of cargo and luggage load capacity. For example, if occupants and cargo should never exceed XXX lbs or “XXX” amount equals 1,400 lbs (635 kg) and there will XXX kg” on the Tire and Loading Information placard.
340 STARTING AND OPERATING • For the following example, the combined weight of occupants and cargo should never exceed 865 lbs • If your vehicle will be towing a trailer, load from your (392 kg). trailer will be transferred to your vehicle. The following table shows examples on how to calculate total load, cargo/luggage, and towing capacities of your vehicle with varying seating configurations and number and size of occupants.
STARTING AND OPERATING 341 5
342 STARTING AND OPERATING WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.
STARTING AND OPERATING 343 WARNING! (Continued) • Unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • Always drive with each tire inflated to the recommended cold tire inflation pressure. Economy Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement.
344 STARTING AND OPERATING CAUTION! After inspecting or adjusting the tire pressure, always reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Tire pressures change by approximately 1 psi (7 kPa) per 12°F (7°C) of air temperature change. Keep this in mind when checking tire pressure inside a garage, especially in the winter.
STARTING AND OPERATING 345 loading may be required for high-speed vehicle opera- Radial Ply Tires tion. Refer to your authorized tire dealer or original equipment vehicle dealer for recommended safe operatWARNING! ing speeds, loading and cold tire inflation pressures. Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle WARNING! poorly. The instability could cause a collision.
346 STARTING AND OPERATING Consult an authorized tire dealer for tire repairs and Summer Or Three Season Tires — If Equipped additional information. Summer tires provide traction in both wet and dry Damaged Run Flat tires, or Run Flat tires that have conditions, and are not intended to be driven in snow or experienced a loss of pressure should be replaced imme- on ice.
STARTING AND OPERATING 347 If you need snow tires, select tires equivalent in size and type to the original equipment tires. Use snow tires only in sets of four; failure to do so may adversely affect the safety and handling of your vehicle. Run Flat Tires — If Equipped Run Flat tires allow you the capability to drive 50 miles (80 km) at 50 mph (80 km/h) after a rapid loss of inflation pressure. This rapid loss of inflation is referred to as the Run Flat mode.
348 STARTING AND OPERATING rotation for your vehicle. If your vehicle has this option, refer to an authorized tire dealer for the recommended NOTE: For vehicles equipped with TIREFIT instead of a tire rotation pattern. spare tire, please refer to “TIREFIT KIT” in “What To Do Compact Spare Tire — If Equipped In Emergencies” for further information.
STARTING AND OPERATING 349 Do not install a wheel cover or attempt to mount a conventional tire on the compact spare wheel, since the wheel is designed specifically for the compact spare tire. Do not install more than one compact spare tire and wheel on the vehicle at any given time. WARNING! Compact spares are for temporary emergency use only. With these spares, do not drive more than 50 mph (80 km/h). Temporary use spares have limited tread life.
350 STARTING AND OPERATING WARNING! Limited-use spares are for emergency use only. Installation of this limited-use spare tire affects vehicle handling. With this tire, do not drive more than the speed listed on the limit-use spare wheel. Keep inflated to the cold tire inflation pressures listed on your Tire and Loading Information Placard located on the driver’s side B-Pillar or the rear edge of the driver’s side door.
STARTING AND OPERATING 351 tread wear indicators, the tire should be replaced. Refer to “Replacement Tires” in this section for further information. Life Of Tire The service life of a tire is dependent upon varying factors including, but not limited to: • Driving style • Tire pressure • Distance driven • Performance tires, tires with a speed rating of V or higher, and summer tires typically have a reduced tread life. Rotation of these tires per the vehicle maintenance schedule is highly recommended.
352 STARTING AND OPERATING WARNING! Tires and the spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure. You could lose control and have a collision resulting in serious injury or death. Information placard or the Vehicle Certification Label for the size designation of your tire. The Load Index and Speed Symbol for your tire will be found on the original equipment tire sidewall.
STARTING AND OPERATING 353 WARNING! WARNING! (Continued) • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle. This can cause unpredictable handling and stress to steering and suspension components. You could lose control and have a collision resulting in serious injury or death.
354 STARTING AND OPERATING The suggested rotation method is the “rearward cross” shown in the following diagram. This rotation pattern The tires on the front and rear of your vehicle operate at does not apply to some directional tires that must not be different loads and perform different steering, driving, reversed. and braking functions. For these reasons, they wear at unequal rates. TIRE ROTATION RECOMMENDATIONS These effects can be reduced by timely rotation of tires.
STARTING AND OPERATING 355 also increase as the vehicle is driven - this is normal and there should be no adjustment for this increased presThe Tire Pressure Monitor System (TPMS) will warn the sure. driver of a low tire pressure based on the vehicle recommended cold placard pressure.
356 STARTING AND OPERATING to be driven for up to 20 minutes above 15 mph (24 km/h) in order for the TPMS to receive this information. For example, your vehicle may have a recommended cold (parked for more than three hours) placard pressure of 30 psi (207 kPa). If the ambient temperature is 68°F (20°C) and the measured tire pressure is 27 psi (186 kPa), a temperature drop to 20°F (-7°C) will decrease the tire pressure to approximately 23 psi (158 kPa).
STARTING AND OPERATING 357 CAUTION! (Continued) • After inspecting or adjusting the tire pressure, always reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the Tire Pressure Monitoring Sensor. NOTE: Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability.
358 STARTING AND OPERATING monitor tire pressure levels. Sensors, mounted to each in one or more of the four active road tires. An ⬙Inflate to wheel as part of the valve stem, transmit tire pressure XX⬙ message will also be displayed. Should this occur, you should stop as soon as possible, check the inflation readings to the Receiver Module.
STARTING AND OPERATING 359 “Tire Pressure Monitoring Telltale Light” will turn off NOTE: when the fault condition no longer exists. A system fault 1. The compact spare tire (if equipped) does not have a can occur due to any of the following: tire pressure monitoring sensor. Therefore, the TPMS 1. Jamming due to electronic devices or driving next to will not monitor the pressure in the compact spare tire. facilities emitting the same Radio Frequencies as the 2.
360 STARTING AND OPERATING 4. For each subsequent ignition key cycle, a chime will monitor tire pressure levels. Sensors, mounted to each sound and the “Tire Pressure Monitoring Telltale wheel as part of the valve stem, transmit tire pressure Light” will flash on and off for 75 seconds and then readings to the Receiver Module. remain on solid. NOTE: It is particularly important for you to check the 5.
STARTING AND OPERATING 361 Tire Pressure Monitoring Low Pressure Warnings The “Tire Pressure Monitoring Telltale Light” will illuminate in the instrument cluster and a chime will sound when tire pressure is low in one or more of the four active road tires. In addition, the Electronic Vehicle Information Center (EVIC) will display a graphic showing the pressure values of each tire with the low tire pressure values flashing. An ⬙Inflate to XX⬙ message will also be displayed.
362 STARTING AND OPERATING 2. Installing some form of aftermarket window tinting NOTE: that affects radio wave signals. 1. The compact spare tire (if so equipped) does not have a tire pressure monitoring sensor. Therefore, the TPMS 3. Lots of snow or ice around the wheels or wheel will not monitor the pressure in the compact spare tire. housings. 4. Using tire chains on the vehicle. 5. Using wheels/tires not equipped with TPM sensors. 2.
STARTING AND OPERATING 363 4. For each subsequent ignition key cycle, a chime will sound, the “Tire Pressure Monitoring Telltale Light” will flash on and off for 75 seconds and then remain on solid, and the EVIC will display a ⬙CHECK TPM SYSTEM⬙ message for a minimum of five seconds and then display dashes (- -) in place of the pressure value. General Information This device complies with part 15 of the FCC rules and RSS 210 of Industry Canada.
364 STARTING AND OPERATING FUEL REQUIREMENTS Over 40 auto manufacturers worldwide have issued and endorsed consistent gasoline specifications (the Worldwide Fuel Charter, WWFC) which define fuel properties necessary to deliver enhanced emissions, performance, and durability for your vehicle. The manufacturer recommends the use of gasolines that meet the WWFC specifications if they are available.
STARTING AND OPERATING 365 Gasoline/Oxygenate Blends E-85 Usage In Non-Flex Fuel Vehicles Some fuel suppliers blend unleaded gasoline with oxy- Non-Flex Fuel Vehicles (FFV) are compatible with gasoline genates such as Ethanol. Fuels blended with oxygenates containing 10% ethanol (E10). Gasoline with higher ethanol content may void the New Vehicle Limited Warranty. may be used in your vehicle. CAUTION! DO NOT use gasoline containing Methanol or gasoline containing more than 10% Ethanol.
366 STARTING AND OPERATING • Disconnect and reconnect the battery to reset the Materials Added To Fuel engine controller memory. All gasoline sold in the United States is required to More extensive repairs will be required for prolonged contain effective detergent additives. Use of additional detergents or other additives is not needed under normal exposure to E-85 fuel. conditions and they would result in additional cost.
STARTING AND OPERATING 367 CAUTION! (Continued) • An out-of-tune engine or certain fuel or ignition malfunctions can cause the catalytic converter to overheat. If you notice a pungent burning odor or some light smoke, your engine may be out of tune or malfunctioning and may require immediate service. Contact your authorized dealer for service assistance. • The use of fuel additives, which are now being sold as octane enhancers, is not recommended.
368 STARTING AND OPERATING WARNING! (Continued) • Guard against carbon monoxide with proper maintenance. Have the exhaust system inspected every time the vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side windows fully open. FLEXIBLE FUEL (3.6L ENGINE ONLY) — IF EQUIPPED E-85 General Information The information in this section is for Flexible Fuel vehicles only.
STARTING AND OPERATING 369 WARNING! Ethanol vapors are extremely flammable and could cause serious personal injury. Never have any smoking materials lit in or near the vehicle when removing the fuel filler tube cap (gas cap) or filling the tank. Do not use E-85 as a cleaning agent and never use it near an open flame. Fuel Requirements E-85 Badge Ethanol Fuel (E-85) E-85 is a mixture of approximately 85% fuel ethanol and 15% unleaded gasoline.
370 STARTING AND OPERATING For best results, a refueling pattern that avoids alternat- • Some additives used in regular gasoline are not fully ing between E-85 and unleaded gasoline is recomcompatible with E-85 and may form deposits in your engine. To eliminate driveability issues that may be mended.
STARTING AND OPERATING 371 Starting Replacement Parts The characteristics of E-85 fuel make it unsuitable for use when ambient temperatures fall below 0°F (-18°C). In the range of 0°F (-18°C) to 32°F (0°C), you may experience an increase in the time it takes for your engine to start, and a deterioration in driveability (sags and/or hesitations) until the engine is fully warmed up. Many components in your Flexible Fuel Vehicle (FFV) are designed to be compatible with ethanol.
372 STARTING AND OPERATING ADDING FUEL Fuel Filler Cap (Gas Cap) The gas cap is behind the fuel filler door, on the left rear quarter panel of the vehicle. If the gas cap is lost or damaged, be sure the replacement cap is for use with this vehicle.
STARTING AND OPERATING 373 After removing the gas cap, place the gas cap tether cable over a hook on the inside of the fuel door. This keeps the gas cap suspended away from and protects the vehicle’s surface. Tether Cable NOTE: If the gas cap is lost or damaged, be sure the replacement cap is for use with this vehicle. CAUTION! • Damage to the fuel system or emission control system could result from using an improper fuel tank filler tube cap (gas cap).
374 STARTING AND OPERATING WARNING! • Never have any smoking materials lit in or near the vehicle when the gas cap is removed or the tank is being filled. • Never add fuel when the engine is running. This is in violation of most state and federal fire regulations and doing so may cause the MIL to turn on. • A fire may result if gasoline is pumped into a portable container that is inside of a vehicle. You could be burned. Always place gas containers on the ground while filling.
STARTING AND OPERATING 375 VEHICLE LOADING Gross Vehicle Weight Rating (GVWR) The GVWR is the total allowable weight of your vehicle. This includes driver, passengers, and cargo. The total Your vehicle has a Vehicle Certification Label affixed to load must be limited so that you do not exceed the the drivers side B-Pillar or the rear of the driver’s door. GVWR.
376 STARTING AND OPERATING Overloading Loading The load carrying components (axle, springs, tires, wheels, etc.) of your vehicle will provide satisfactory service as long as you do not exceed the GVWR and the front and rear GAWR. To load your vehicle properly, first figure out its empty weight, axle-by-axle and side-by-side. Store heavier items down low and be sure you distribute their weight as evenly as possible. Stow all loose items securely before driving.
STARTING AND OPERATING 377 To maintain the New Vehicle Limited Warranty coverage, ready for operation⬙ condition. The recommended way to follow the requirements and recommendations in this measure GTW is to put your fully loaded trailer on a vehicle scale. The entire weight of the trailer must be manual concerning vehicles used for trailer towing. supported by the scale.
378 STARTING AND OPERATING WARNING! It is important that you do not exceed the maximum front or rear GAWR. A dangerous driving condition can result if either rating is exceeded. You could lose control of the vehicle and have a collision. Frontal Area The frontal area is the maximum height multiplied by the maximum width of the front of a trailer.
STARTING AND OPERATING 379 Trailer Hitch Classification The following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition. Trailer Hitch Classification Definitions Class Max.
380 STARTING AND OPERATING Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/Transmission 2.4L/Auto 3.6L/Auto Max. Frontal Area Max. Gross Trailer Wt. (GTW) 1,000 lbs (450 kg) 11 sq.ft. (1.0 sq.m) (See Note 2) 22 sq.ft. (2.0 sq.m) 1,000 lbs (450 kg) Refer to local laws for maximum trailer towing speeds.
STARTING AND OPERATING 381 Trailer And Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% to 15% of the Gross Trailer Weight (GTW) on the tow hitch of your vehicle. Loads balanced over the wheels or heavier in the rear can cause the trailer to sway severely side to side which will cause loss of control of the vehicle and trailer. Failure to load trailers heavier in front is the cause of many trailer collisions.
382 STARTING AND OPERATING NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options or dealer-installed options must be considered as part of the total load on your vehicle. Refer to the “Tire and Loading Information” placard for the maximum combined weight of occupants and cargo for your vehicle.
STARTING AND OPERATING 383 WARNING! WARNING! (Continued) Improper towing can lead to a collision. Follow these guidelines to make your trailer towing as safe as possible: • Make certain that the load is secured in the trailer and it will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control. You could lose control of your vehicle and have a collision.
384 STARTING AND OPERATING WARNING! (Continued) • Total weight must be distributed between the tow vehicle and the trailer such that the following four ratings are not exceeded: 1. Max loading as defined on the “Tire and Loading Information” placard. 2. GTW 3. GAWR 4. Tongue weight rating for the trailer hitch utilized. • Proper tire inflation pressures are essential to the safe and satisfactory operation of your vehicle.
STARTING AND OPERATING 385 Towing Requirements — Trailer Brakes • Do not interconnect the hydraulic brake system or vacuum system of your vehicle with that of the trailer. This could cause inadequate braking and possible personal injury. • An electronically actuated trailer brake controller is required when towing a trailer with electronically actuated brakes. When towing a trailer equipped with a hydraulic surge actuated brake system, an electronic brake controller is not required.
386 STARTING AND OPERATING CAUTION! If the trailer weighs more than 1,000 lbs (454 kg) loaded, it should have its own brakes and they should be of adequate capacity. Failure to do this could lead to accelerated brake lining wear, higher brake pedal effort, and longer stopping distances. The electrical connections are all complete to the vehicle, but you must mate the harness to a trailer connector. Refer to the following illustrations.
STARTING AND OPERATING 387 Towing Tips Before setting out on a trip, practice turning, stopping, and backing up the trailer in an area located away from heavy traffic. Automatic Transmission The DRIVE range can be selected when towing. However, if frequent shifting occurs while in DRIVE, select the ⬙3⬙ range (with four-speed transmission) or select a lower gear using the AutoStick® shift control (with six-speed transmission).
388 STARTING AND OPERATING If you REGULARLY TOW a trailer for more than 45 • To prevent excess heat generation, avoid continuous driving at high RPM. Reduce vehicle speed as necessary minutes of continuous operation, then change the autoto avoid extended driving at high RPM. Return to a matic transmission fluid and filter as specified for “pohigher gear or vehicle speed when grade and road lice, taxi, fleet, or frequent trailer towing.” Refer to the conditions allow.
STARTING AND OPERATING 389 Cooling System Highway Driving To reduce potential for engine and transmission over- Reduce speed. heating, take the following actions: Air Conditioning City Driving Turn off temporarily. When stopped for short periods of time, shift the transmission into NEUTRAL and increase engine idle speed. RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.
390 STARTING AND OPERATING Recreational Towing — All Models Recreational towing is allowed ONLY if the front wheels are OFF the ground. This may be accomplished using a tow dolly or vehicle trailer. If using a tow dolly, follow this procedure: 1. Properly secure the dolly to the tow vehicle, following the dolly manufacturer’s instructions. 2. Drive the front wheels onto the tow dolly. 3. Firmly apply the parking brake. Place the transmission in PARK. 4.
WHAT TO DO IN EMERGENCIES CONTENTS 䡵 HAZARD WARNING FLASHERS . . . . . . . . . . .392 ▫ Preparations For Jacking . . . . . . . . . . . . . . . .397 䡵 IF YOUR ENGINE OVERHEATS . . . . . . . . . . . .392 ▫ Jacking Instructions . . . . . . . . . . . . . . . . . . .398 ▫ Engine Oil Overheating (2.4L Engine Only) — If Equipped. . . . . . . . . . . . . . . . . . . . . . . . . .393 ▫ Road Tire Installation . . . . . . . . . . . . . . . . . . .405 䡵 WHEEL AND TIRE TORQUE SPECIFICATIONS . . . . . . . . . . . .
392 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHERS IF YOUR ENGINE OVERHEATS The Hazard Warning flasher switch is located on the In any of the following situations, you can reduce the potential for overheating by taking the appropriate action. instrument panel, below the radio. Press the switch to turn on the Hazard Warning • On the highways — Slow down. flasher.
WHAT TO DO IN EMERGENCIES 393 NOTE: There are steps that you can take to slow down Engine Oil Overheating (2.4L Engine Only) — If an impending overheat condition: Equipped • If your air conditioner (A/C) is on, turn it off. The A/C During sustained high-speed driving or trailer tow up system adds heat to the engine cooling system and long grades on a hot day, the engine oil temperature may turning the A/C off can help remove this heat. become too hot.
394 WHAT TO DO IN EMERGENCIES Inspect the wheel mounting surface prior to mounting Proper lug nut/bolt torque is very important to ensure the tire and remove any corrosion or loose particles. that the wheel is properly mounted to the vehicle. Any time a wheel has been removed and reinstalled on the vehicle the lug nuts/bolts should be torqued using a properly calibrated torque wrench.
WHAT TO DO IN EMERGENCIES 395 Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been tightened twice. WARNING! To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle has been lowered. Failure to follow this warning may result in personal injury. JACKING AND TIRE CHANGING WARNING! Torque Patterns After 25 miles (40 km) check the lug nut/bolt torque to be sure that all the lug nuts/bolts are properly seated against the wheel.
396 WHAT TO DO IN EMERGENCIES WARNING! (Continued) • Being under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never put any part of your body under a vehicle that is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift. • Never start or run the engine while the vehicle is on a jack. • The jack is designed to be used as a tool for changing tires only.
WHAT TO DO IN EMERGENCIES 397 Preparations For Jacking 1. Park the vehicle on a firm, level surface. Avoid ice or slippery areas. WARNING! Do not attempt to change a tire on the side of the vehicle close to moving traffic, pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. 2. Turn on the Hazard Warning flashers. 3. Set the parking brake. 4. Place the shift lever into PARK (automatic transmission) or REVERSE (manual transmission). 5.
398 WHAT TO DO IN EMERGENCIES Jacking Instructions WARNING! (Continued) WARNING! Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: • Always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle. • Turn on the Hazard Warning flashers. • Block the wheel diagonally opposite the wheel to be raised. • Set the parking brake firmly and set an automatic transmission in PARK; a manual transmission in REVERSE.
WHAT TO DO IN EMERGENCIES 399 NOTE: The jack handle attaches to the side of the jack with two attachment points. When the jack is partially expanded, the tension between the two attachment points holds the jack handle in place. Jack Warning Label CAUTION! Do not attempt to raise the vehicle by jacking on locations other than those indicated in the Jacking Instructions for this vehicle.
400 WHAT TO DO IN EMERGENCIES 2. Loosen, but do not remove, the wheel nuts by turning them to the left one turn while the wheel is still on the ground. CAUTION! Do not attempt to raise the vehicle by jacking on locations other than those indicated in step 3. Jacking Locations 3. There is a front and rear jacking location on each side of the vehicle. The plastic trim has been cut away to expose the jacking locations on the body.
WHAT TO DO IN EMERGENCIES 401 6 Front Jacking Location Rear Jacking Location 4. Turn the jack screw to the left until the jack can be placed under the jacking location. Once the jack is positioned, turn the jack screw to the right until the jack head is properly engaged to the jacking location on the wheel to be changed. Do not raise the vehicle until you are sure the jack is securely engaged.
402 WHAT TO DO IN EMERGENCIES Jack Engaged (Front Jacking Location) Jack Engaged (Rear Jacking Location) WARNING! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire.
WHAT TO DO IN EMERGENCIES 403 5. Raise the vehicle by turning the jack screw to the right, using the jack handle. Raise the vehicle only until the tire just clears the surface and enough clearance is obtained to install the spare tire. Minimum tire lift provides maximum stability. 6. Remove the wheel nuts, and pull the wheel and wheel covers (where applicable) off the hub. Install the spare wheel and wheel nuts with the cone shaped end of the nuts toward the wheel. Lightly tighten the nuts.
404 WHAT TO DO IN EMERGENCIES WARNING! • To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle has been lowered. Failure to follow this warning may result in personal injury. • To avoid possible personal injury, handle the wheel covers with care to avoid contact with any sharp edges. 7. Lower the vehicle by turning the jack screw to the left. 9. Lower the jack until it is free. Remove the wheel blocks.
WHAT TO DO IN EMERGENCIES 405 Road Tire Installation Vehicles Equipped With Wheel Covers 1. Mount the road tire on the axle. 2. To ease the installation process for steel wheels with wheel covers, install two lug nuts on the mounting studs which are on each side of the valve stem. Install the lug nuts with the cone shaped end of the nut toward the wheel. Lightly tighten the lug nuts.
406 WHAT TO DO IN EMERGENCIES 3. Align the valve notch in the wheel cover with the 6. Finish tightening the lug nuts. Push down on the valve stem on the wheel. Install the cover by hand, wrench while at the end of the handle for increased snapping the cover over the two lug nuts. Do not use leverage. Tighten the lug nuts in a star pattern until a hammer or excessive force to install the cover. each nut has been tightened twice. For the correct lug nut torque refer to Torque Specifications in this sec4.
WHAT TO DO IN EMERGENCIES 407 WARNING! To avoid the risk of forcing the vehicle off the jack, do not tighten the wheel nuts fully until the vehicle has been lowered. Failure to follow this warning may result in personal injury. 5. After 25 miles (40 km) check the lug nut torque with a torque wrench to ensure that all lug nuts are properly seated against the wheel. JUMP-STARTING If your vehicle has a discharged battery it can be jumpstarted using a set of jumper cables and a battery in 3.
408 WHAT TO DO IN EMERGENCIES CAUTION! Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or electrical system may occur. NOTE: When using a portable battery booster pack follow the manufacturer’s operating instructions and precautions.
WHAT TO DO IN EMERGENCIES 409 WARNING! • Take care to avoid the radiator cooling fan whenever the hood is raised. It can start anytime the ignition switch is ON. You can be injured by moving fan blades. • Remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact. You could be seriously injured. • Batteries contain sulfuric acid that can burn your skin or eyes and generate hydrogen gas which is flammable and explosive.
410 WHAT TO DO IN EMERGENCIES 4. If using another vehicle to jump-start the battery, park the vehicle within the jumper cables reach, set the parking brake and make sure the ignition is OFF. WARNING! Do not allow vehicles to touch each other as this could establish a ground connection and personal injury could result. Jump-Starting Procedure WARNING! Failure to follow this jump-starting procedure could result in personal injury or property damage due to battery explosion.
WHAT TO DO IN EMERGENCIES 411 WARNING! Do not connect the jumper cable to the negative (-) post of the discharged battery. The resulting electrical spark could cause the battery to explode and could result in personal injury. Only use the specific ground point, do not use any other exposed metal parts. Disconnecting The Jumper Cables 1. Disconnect the negative (-) jumper cable from the remote negative (-) post of the vehicle with the discharged battery. 2.
412 WHAT TO DO IN EMERGENCIES CAUTION! CAUTION! Accessories plugged into the vehicle power outlets draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.). Eventually, if plugged in long enough without engine operation, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting. Racing the engine or spinning the wheels may lead to transmission overheating and failure.
WHAT TO DO IN EMERGENCIES 413 CAUTION! WARNING! (Continued) • When “rocking” a stuck vehicle by shifting between DRIVE and REVERSE, do not spin the wheels faster than 15 mph (24 km/h), or drivetrain damage may result. • Revving the engine or spinning the wheels too fast may lead to transmission overheating and failure. It can also damage the tires. Do not spin the wheels above 30 mph (48 km/h) while in gear (no transmission shifting occurring). explode and injure someone.
414 WHAT TO DO IN EMERGENCIES 4. Turn the ignition to the ACC or ON/RUN position, 7. Move the shift lever to the NEUTRAL position. but do not start the engine. 8. The vehicle may then be started in NEUTRAL. 5. Press and maintain firm pressure on the brake pedal. 9. Reinstall the cupholder liner. 6. Insert a screwdriver or similar tool into the access hole (at the front of the cupholder) and push and hold the override release lever forward.
WHAT TO DO IN EMERGENCIES 415 Proper towing or lifting equipment is required to prevent damage to your vehicle. Use only tow bars and other equipment designed for this purpose, following equipment manufacturer’s instructions. Use of safety chains is mandatory. Attach a tow bar or other towing device to main structural members of the vehicle, not to bumpers or associated brackets. State and local laws regarding vehicles under tow must be observed. If you must use the accessories (wipers, defrosters, etc.
416 WHAT TO DO IN EMERGENCIES • The towing distance must not exceed 15 mi (24 km). • The towing speed must not exceed 25 mph (40 km/h). If the transmission is not operable, or the vehicle must be towed faster than 25 mph (40 km/h) or farther than 15 mi (24 km), it must be towed with the front wheels OFF the ground (using a flatbed truck, towing dolly, or wheel lift equipment with the front wheels raised). flatbed towing vehicle is not available, wheel lift towing equipment may be used.
MAINTAINING YOUR VEHICLE CONTENTS 䡵 ENGINE COMPARTMENT — 2.4L . . . . . . . . . .419 ▫ Engine Oil Filter . . . . . . . . . . . . . . . . . . . . . .428 䡵 ENGINE COMPARTMENT — 3.6L . . . . . . . . . .420 ▫ Engine Air Cleaner Filter . . . . . . . . . . . . . . . .428 䡵 ONBOARD DIAGNOSTIC SYSTEM — OBD II . .421 ▫ Maintenance-Free Battery . . . . . . . . . . . . . . .429 ▫ Loose Fuel Filler Cap Message . . . . . . . . . . . .421 ▫ Air Conditioner Maintenance . . . . . . . . . . . . .
418 MAINTAINING YOUR VEHICLE ▫ Brake System . . . . . . . . . . . . . . . . . . . . . . . .444 ▫ Headlamp . . . . . . . . . . . . . . . . . . . . . . . . . .464 ▫ Automatic Transmission . . . . . . . . . . . . . . . .446 ▫ Front Turn Signal . . . . . . . . . . . . . . . . . . . . .467 ▫ Appearance Care And Protection From Corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . .450 ▫ Front Fog Lamp . . . . . . . . . . . . . . . . . . . . . .468 ▫ Cleaning Center Console Cupholders. . . . . . .
MAINTAINING YOUR VEHICLE 419 ENGINE COMPARTMENT — 2.
420 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT — 3.
MAINTAINING YOUR VEHICLE 421 ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
422 MAINTAINING YOUR VEHICLE persists, the message will appear the next time the vehicle is started. This might indicate a damaged cap. If the problem is detected twice in a row, the system will turn on the “Malfunction Indicator Light (MIL).” Resolving the problem will turn the MIL light off. Normally, the OBD II system will be ready. The OBD II system may not be ready if your vehicle was recently serviced, recently had a dead battery or a battery replacement.
MAINTAINING YOUR VEHICLE 423 3. Approximately 15 seconds later, one of two things will Regardless of whether your vehicle’s OBD II system is happen: ready or not, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced • The MIL will flash for about 10 seconds and then before going to the I/M station. The I/M station can fail return to being fully illuminated until you turn OFF your vehicle because the MIL is on with the engine the ignition or start the engine.
424 MAINTAINING YOUR VEHICLE available which include detailed service information for Besides those maintenance items specified in the fixed your vehicle. Refer to these Service Manuals before “Maintenance Schedule”, there are other components which may require servicing or replacement in the future. attempting any procedure yourself. NOTE: Intentional tampering with emissions control systems may void your warranty and could result in civil penalties being assessed against you.
MAINTAINING YOUR VEHICLE 425 CAUTION! (Continued) • Your vehicle has been built with improved fluids that protect the performance and durability of your vehicle and also allow extended maintenance intervals. Do not use chemical flushes in these components as the chemicals can damage your engine, transmission, power steering or air conditioning. Such damage is not covered by the New Vehicle Limited Warranty.
426 MAINTAINING YOUR VEHICLE CAUTION! Do not overfill the engine. Overfilling the engine will cause oil aeration, which can lead to loss of oil pressure and an increase in oil temperature. This could damage your engine. Also, be sure the oil fill cap is replaced and tightened after adding oil.
MAINTAINING YOUR VEHICLE 427 CAUTION! Do not use chemical flushes in your engine oil as the chemicals can damage your engine. Such damage is not covered by the New Vehicle Limited Warranty. Engine Oil Viscosity — 2.4L Engine Engine Oil Viscosity — 3.6L Engine MOPAR® SAE 5W-20 engine oil approved to Chrysler Material Standard MS-6395 such as Pennzoil®, Shell Helix® or equivalent is recommended for all operating temperatures. This engine oil improves low temperature starting and vehicle fuel economy.
428 MAINTAINING YOUR VEHICLE station or governmental agency for advice on how and where used oil and oil filters can be safely discarded in You may use synthetic engine oils provided the recomyour area. mended oil quality requirements are met, and the recommended maintenance intervals for oil and filter changes Engine Oil Filter are followed. The engine oil filter should be replaced with a new filter Materials Added To Engine Oil at every engine oil change.
MAINTAINING YOUR VEHICLE 429 WARNING! The air induction system (air cleaner, hoses, etc.) can provide a measure of protection in the case of engine backfire. Do not remove the air induction system (air cleaner, hoses, etc.) unless such removal is necessary for repair or maintenance. Make sure that no one is near the engine compartment before starting the vehicle with the air induction system (air cleaner, hoses, etc.) removed. Failure to do so can result in serious personal injury.
430 MAINTAINING YOUR VEHICLE WARNING! CAUTION! • Battery fluid is a corrosive acid solution and can burn or even blind you. Do not allow battery fluid to contact your eyes, skin, or clothing. Do not lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area immediately with large amounts of water. • Battery gas is flammable and explosive. Keep flame or sparks away from the battery.
MAINTAINING YOUR VEHICLE 431 of the condenser fins and a performance test. Drive belt tension should also be checked at this time. WARNING! • Use only refrigerants and compressor lubricants approved by the manufacturer for your air conditioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs.
432 MAINTAINING YOUR VEHICLE 3. Disconnect the glove box door dampener from the slot on the side of the box. This is done by grasping the Refer to the “Maintenance Schedule” for the proper dampener connector (on the outside of the box) and the maintenance intervals. end of the connector pin (on the inside of the box) with your thumb and forefinger and pulling outward while WARNING! lightly lifting upward on the door with your other hand.
MAINTAINING YOUR VEHICLE 433 7. Install the A/C Air Filter with the arrow on the filter pointing toward the floor. When installing the filter cover, make sure the retaining tabs fully engage the cover. CAUTION! The A/C air filter is identified with an arrow to indicate airflow direction through the filter. Failure to install the filter properly will result in the need to replace it more often. A/C Air Filter Replacement 8. Reinstall the glove box door dampener and glove box. 6.
434 MAINTAINING YOUR VEHICLE operation and to protect against rust and wear. Prior to the application of any lubricant, the parts concerned should be wiped clean to remove dust and grit; after lubricating excess oil and grease should be removed. Particular attention should also be given to hood latching components to ensure proper function. When performing other underhood services, the hood latch, release mechanism and safety catch should be cleaned and lubricated.
MAINTAINING YOUR VEHICLE 435 reservoir with windshield washer solvent (not radiator Exhaust System antifreeze) and operate the system for a few seconds to The best protection against carbon monoxide entry into flush out the residual water. the vehicle body is a properly maintained engine exhaust When refilling the washer fluid reservoir, apply some system. washer fluid to a cloth or towel and wipe the wiper If you notice a change in the sound of the exhaust system; blades clean.
436 MAINTAINING YOUR VEHICLE WARNING! CAUTION! • Exhaust gases can injure or kill. They contain carbon monoxide (CO), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing CO, refer to “Safety Tips/Exhaust Gas” in “Things To Know Before Starting Your Vehicle” for further information. • A hot exhaust system can start a fire if you park over materials that can burn.
MAINTAINING YOUR VEHICLE 437 Under normal operating conditions, the catalytic con- To minimize the possibility of catalytic converter damage: verter will not require maintenance. However, it is im- • Do not shut off the engine or interrupt the ignition, portant to keep the engine properly tuned to assure when the transmission is in gear and the vehicle is in proper catalyst operation and prevent possible catalyst motion. damage.
438 MAINTAINING YOUR VEHICLE Cooling System WARNING! • When working near the radiator cooling fan, disconnect the fan motor lead or turn the ignition switch to the LOCK position. The fan is temperature controlled and can start at anytime the ignition switch is in the ON position. • You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator. If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.
MAINTAINING YOUR VEHICLE 439 Refer to the “Maintenance Schedule” for the proper maintenance intervals. NOTE: Some vehicles require special tools to add coolant properly. Failure to fill these systems properly could lead to severe internal engine damage. If any coolant is needed to be added to the system please contact your local authorized dealer. Selection Of Coolant Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for further information.
440 MAINTAINING YOUR VEHICLE CAUTION! (Continued) • Do not use water alone or alcohol-based engine coolant (antifreeze) products. Do not use additional rust inhibitors or antirust products, as they may not be compatible with the radiator engine coolant and may plug the radiator. • This vehicle has not been designed for use with propylene glycol-based engine coolant (antifreeze). Use of propylene glycol-based engine coolant (antifreeze) is not recommended.
MAINTAINING YOUR VEHICLE 441 • Use only high purity water such as distilled or deion- • Mixing engine coolant (antifreeze) types is not recomized water when mixing the water/engine coolant mended and can result in cooling system damage. If HOAT and OAT coolant are mixed in an emergency, (antifreeze) solution.
442 MAINTAINING YOUR VEHICLE WARNING! • Do not open hot engine cooling system. Never add engine coolant (antifreeze) when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system. To prevent scalding or injury, do not remove the pressure cap while the system is hot or under pressure. • Do not use a pressure cap other than the one specified for your vehicle. Personal injury or engine damage may result.
MAINTAINING YOUR VEHICLE 443 The radiator normally remains completely full, so there is no need to remove the radiator cap unless checking for engine coolant (antifreeze) freeze point or replacing coolant. Advise your service attendant of this. As long as the engine operating temperature is satisfactory, the coolant bottle need only be checked once a month. When additional engine coolant (antifreeze) is needed to maintain the proper level, it should be added to the coolant bottle. Do not overfill.
444 MAINTAINING YOUR VEHICLE • Keep the front of the radiator clean. If your vehicle is equipped with air conditioning, keep the front of the condenser clean. • Do not change the thermostat for Summer or Winter operation. If replacement is ever necessary, install ONLY the correct type thermostat. Other designs may result in unsatisfactory engine coolant (antifreeze) performance, poor gas mileage, and increased emissions.
MAINTAINING YOUR VEHICLE 445 Overfilling of fluid is not recommended because it may cause leaking in the system. Fluid level can be expected to fall as the brake pads wear. Brake fluid level should be checked when pads are replaced. However, low fluid level may be caused by a leak and a checkup may be needed. Use only manufacturer’s recommended brake fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for further information.
446 MAINTAINING YOUR VEHICLE WARNING! (Continued) WARNING! (Continued) • To avoid contamination from foreign matter or moisture, use only new brake fluid or fluid that has been in a tightly closed container. Keep the master cylinder reservoir cap secured at all times. Brake fluid in a open container absorbs moisture from the air resulting in a lower boiling point. This may cause it to boil unexpectedly during hard or prolonged braking, resulting in sudden brake failure. This could result in a collision.
MAINTAINING YOUR VEHICLE 447 NOTE: No chemical flushes should be used in any Automatic Transmission Fluid (ATF) is an engineered transmission; only the approved lubricant should be product and its performance may be impaired by supplemental additives. Therefore, do not add any fluid addiused. tives to the transmission. The only exception to this policy is the use of special dyes for diagnosing fluid CAUTION! leaks.
448 MAINTAINING YOUR VEHICLE 2. Run the engine at normal idle speed for at least 60 7. Wipe the dipstick clean and reinsert it until seated. seconds, and leave the engine running for the rest of Then, remove the dipstick and note the fluid level on this procedure. both sides. The fluid level reading is only valid if there is a solid coating of oil on both sides of the dipstick. 3. Fully apply the parking brake, and press the brake Note that the holes in the dipstick will be full of fluid pedal.
MAINTAINING YOUR VEHICLE 449 To prevent dirt and water from entering the transmission Fluid Level Check — Six-Speed Transmission after checking or replenishing fluid, make sure that the The fluid level is preset at the factory and does not dipstick cap is properly reseated. require adjustment under normal operating conditions.
450 MAINTAINING YOUR VEHICLE The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion Refer to the ⬙Maintenance Schedule⬙ for the proper resistance built into your vehicle. maintenance intervals. In addition, change the fluid and filter if the fluid becomes contaminated (with water, etc.), What Causes Corrosion? or if the transmission is disassembled for any reason.
MAINTAINING YOUR VEHICLE 451 Washing • Wash your vehicle regularly. Always wash your vehicle in the shade using MOPAR® Car Wash, or a mild car wash soap, and rinse the panels completely with clear water. CAUTION! • Do not use abrasive or strong cleaning materials such as steel wool or scouring powder that will scratch metal and painted surfaces. • Use of power washers exceeding 1,200 psi (8 274 kPa) can result in damage or removal of paint and decals.
452 MAINTAINING YOUR VEHICLE • If your vehicle is damaged due to a collision or similar • To remove heavy soil and/or excessive brake dust, use MOPAR® Wheel Cleaner. cause that destroys the paint and protective coating, have your vehicle repaired as soon as possible. The NOTE: If your vehicle is equipped with Dark Vapor cost of such repairs is considered the responsibility of Chrome wheels DO NOT USE wheel cleaners, abrasives the owner. or polishing compounds.
MAINTAINING YOUR VEHICLE 453 Cleaning Headlights Stain Repel Fabric Cleaning Procedure — If Your vehicle is equipped with plastic headlights and fog Equipped lights that are lighter and less susceptible to stone breakage Stain Repel seats may be cleaned in the following manner: than glass headlights. • Remove as much of the stain as possible by blotting Plastic is not as scratch resistant as glass and therefore with a clean, dry towel. different lens cleaning procedures must be followed.
454 MAINTAINING YOUR VEHICLE Interior Care Instrument Panel Cover The instrument panel cover has a low glare surface, which minimizes reflections in the windshield. Do not use protectants or other products, which may cause undesirable reflections. Use soap and warm water to restore the low glare surface.
MAINTAINING YOUR VEHICLE 455 1. Clean with a wet soft rag. A mild soap solution may be used, but do not use high alcohol content or abrasive All glass surfaces should be cleaned on a regular basis cleaners. If soap is used, wipe clean with a clean damp with MOPAR® Glass Cleaner, or any commercial rag. household-type glass cleaner. Never use an abrasive type cleaner. Use caution when cleaning the inside rear win- 2. Dry with a soft cloth.
456 MAINTAINING YOUR VEHICLE Cleaning Center Console Cupholders Removal Grab the rubber portion of the cupholder and lift upward. Cleaning Soak the rubber cupholder liner in a mixture of medium hot tap water and one teaspoon of mild liquid dish soap. Let soak for approximately one hour. After one hour pull the liner from the water and dip it back into the water about six times. This will loosen any remaining debris. Rinse the liner thoroughly under warm running water.
MAINTAINING YOUR VEHICLE 457 WARNING! (Continued) • If a general protection fuse for safety systems (air bag system, braking system), power unit systems (engine system, gearbox system) or steering system blows, contact an authorized dealer. Integrated Power Module The Integrated Power Module is located in the engine compartment near the air cleaner assembly. This center contains cartridge fuses and mini fuses. A label that identifies each component may be printed on the inside of the cover.
458 MAINTAINING YOUR VEHICLE 2 Cartridge Fuse — 3 — Cavity 4 — 5 — 6 — Mini Fuse 20 Amp Yellow 10 Amp Red 10 Amp Red 20 Amp Yellow 10 Amp Red Description Brake Vacuum Pump Center High Mounted Stop Light (CHMSL)/ Brake Switch Ignition Switch Trailer Tow – If Equipped Power Mirror Switch/Climate Controls 7 Cartridge Fuse — 8 — 9 40 Amp Green 10 — 20 Amp Yellow 11 — 15 Amp Lt Blue Cavity Mini Fuse 30 Amp Green 30 Amp Green Description Ignition Off Draw (IOD) Sense 1 Ignition Off Dr
MAINTAINING YOUR VEHICLE 459 12 Cartridge Fuse — 13 — 14 — 15 40 Amp Green — Cavity 16 Mini Fuse Description 20 Amp Yellow 20 Amp Yellow 10 Amp Red — Spare Radiator Fan Relay 15 Amp Lt. Blue Sunroof – If Equipped Ignition/Cigar Lighter Instrument Panel Cavity 17 18 Cartridge Fuse — 19 40 Amp Green — 20 — 21 — Mini Fuse 10 Amp Red — 20 Amp Yellow 15 Amp Lt.
460 MAINTAINING YOUR VEHICLE 22 Cartridge Fuse — 23 — 24 — 25 — 26 — Cavity Mini Fuse 10 Amp Red 15 Amp Lt. Blue 25 Amp Natural 10 Amp Red 15 Amp Lt.
MAINTAINING YOUR VEHICLE 461 Cavity 30 31 32 33 Cartridge Fuse — — 30 Amp Pink — Mini Fuse 20 Amp Yellow — — 10 Amp Red Description Cavity Ignition Run – Heated Seats – If Equipped Spare Auto Shutdown (ASD) Relay 1 Switch Bank/ Diagnostic Link Connector/ Powertrain Control Module (PCM) 34 35 Cartridge Fuse 30 Amp Pink 40 Amp Green Mini Fuse — — Description Anti-Lock Brakes (ABS) Module – If Equipped/ Electronic Stability Control (ESC) Module – If Equipped Anti-Lock Brakes (ABS) Module – If Eq
462 MAINTAINING YOUR VEHICLE Cavity 36 37 Cartridge Fuse 30 Amp Pink — Mini Fuse — 25 Amp Natural Description Passenger Door Module (PDM)/ Driver Door Module (DDM) Power Top Module – If Equipped CAUTION! • When installing the Integrated Power Module cover, it is important to ensure the cover is properly positioned and fully latched. Failure to do so may allow water to get into the Integrated Power Module, and possibly result in an electrical system failure.
MAINTAINING YOUR VEHICLE 463 VEHICLE STORAGE REPLACEMENT BULBS If you will not be using your vehicle for more than 21 days, you may want to take steps to preserve your Interior Bulbs Bulb Number battery. 578/W5W • Disengage the mini-fuse in the Power Distribution Front Courtesy/Reading Lamp Center labeled IOD (Ignition Off-Draw). Center Courtesy/Reading 578/W5W • Or disconnect the negative cable from the battery. Lamp • Anytime you store your vehicle, or keep it out of Visor Vanity Lamp A6220 service (i.
464 MAINTAINING YOUR VEHICLE Exterior Bulbs Bi-Halogen Headlamp Front Turn Signal Lamp Front Park Lamp Front Fog Lamp Center High Mounted Stop (CHMSL) Lamp Rear Tail/Stop/Turn Signal Lamp Backup Lamp License Lamp Front Side Marker Lamp BULB REPLACEMENT Bulb Number HIR2 3157NAK LED (Serviced at Authorized Dealer) H11 LED (Serviced at Authorized Dealer) LED (Serviced at Authorized Dealer) 921 W5W WY5W NOTE: Lens fogging can occur under certain atmospheric conditions.
MAINTAINING YOUR VEHICLE 465 2. To begin removal of the driver side headlamp, reach in To begin removal of the passenger side headlamp, reach in through the inner fender or from the engine compart- through the engine compartment and grasp the bulb cover. ment and grasp the bulb cover.
466 MAINTAINING YOUR VEHICLE 3. Rotate bulb cover and one-quarter turn and pull outward from assembly. Headlamp Bulb Removal Headlamp Bulb Cover Removal 4. Rotate bulb and connector one-quarter turn and pull outward from assembly. CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. 5. Pull the bulb out of the socket and replace the bulb.
MAINTAINING YOUR VEHICLE 467 8. Place bulb cover back and rotate one-quarter turn clockwise to secure. Front Turn Signal 1. Raise and prop open the hood. 2. Rotate the bulb’s electrical connector one-quarter turn counterclockwise and remove it from the headlamp housing. 3. Remove the bulb from the connector socket and install the replacement bulb. Headlamp Bulb 6. If the bulb comes in contact with any oily surface, wipe the bulb with a clean cloth and rubbing alcohol. 7.
468 MAINTAINING YOUR VEHICLE 3. Install the bulb and connector assembly into the fog lamp housing and rotate the connector one-quarter NOTE: Access to the lamps through the lower fascia turn clockwise to lock it in place. cutout is limited. We recommend you access the lamps by turning the steering wheel to allow access and remove Backup Lamps the inner fender shield. 1. Open the trunk and gently pull back the trunk liner behind the tail lamp (requires removal of a push pin 1.
MAINTAINING YOUR VEHICLE 469 3. Grasp the tail lamp by both the outboard and inboard sides, and pull firmly to disengage the tail lamp from the vehicle. NOTE: It is normal to hear a loud sound when the lower tail lamp area unsnaps from the vehicle mounting bracket during tail lamp removal. Tail Lamp Wing Nut NOTE: Placing a small flat head screwdriver or similar tool between the lamp outboard ball stud and plastic grommet from inside the trunk can help to disengage the outboard edge of the tail lamp.
470 MAINTAINING YOUR VEHICLE License Plate Lamp 1. Using a small screwdriver, press inward the locking tab on the side of the lamp assembly and pull down on the lamp assembly for removal. 2. Pull bulb from socket, replace, and reinstall the lamp assembly into place ensuring the locking tab is secure. Tail Lamp Housing 4. Twist and remove socket from lamp. 5. Remove bulb from socket and replace. 6. Reinstall the tail lamp, fasteners, and trunk liner.
MAINTAINING YOUR VEHICLE 471 FLUID CAPACITIES U.S. Fuel (Approximate) All Engines — (Except 2.4L PZEV) 16.9 Gallons 2.4L PZEV (Partial Zero Emissions Vehicle) 18.5 Gallons Engine Oil With Filter 2.4L Engine (SAE 5W-20, API Certified) 4.5 Quarts 3.6L Engine (SAE 5W-20, API Certified) 6 Quarts Cooling System* 2.4L Engine (MOPAR® Antifreeze/Engine Coolant 10 7.7 Quarts Year/150,000 Mile Formula or equivalent) 3.6L Engine (MOPAR® Antifreeze/Engine Coolant 10 11.
472 MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant Engine Oil – 2.4L Engine Engine Oil – 3.6L Engine Engine Oil Filter Spark Plugs – 2.4L Engine except PZEV* Fluid, Lubricant, or Genuine Part We recommend you use MOPAR® Antifreeze/Coolant 10 Year/150,000 Mile Formula OAT (Organic Additive Technology).
MAINTAINING YOUR VEHICLE 473 Component Fluid, Lubricant, or Genuine Part Spark Plugs – 2.4L with We recommend you use MOPAR® Spark Plugs (Gap 0.031 in [0.8 mm]). PZEV* Spark Plugs – 3.6L Engine We recommend you use MOPAR® Spark Plugs (Gap 0.043 in [1.1 mm]). Fuel Selection 87 Octane * PZEV = Partial Zero Emission Vehicle Chassis Component Automatic Transmission Brake Master Cylinder Power Steering Reservoir Fluid, Lubricant, or Genuine Part Use only ATF+4® Automatic Transmission Fluid.
M A I N T E N A ▫ Maintenance Chart. . . . . . . . . . . . . . . . . . . . .478 N C E MAINTENANCE SCHEDULES CONTENTS 䡵 MAINTENANCE SCHEDULE . . . . . . . . . . . . .
M A I N T E N A N C E S C H E D U L E S 8 476 MAINTENANCE SCHEDULES than your authorized dealer, the message can be reset by referring to the steps described under “Electronic Vehicle Your vehicle is equipped with an automatic oil change Information Center (EVIC)/Oil Change Required” in indicator system. The oil change indicator system will “Understanding Your Instrument Panel” for further inremind you that it is time to take your vehicle in for formation. scheduled maintenance.
MAINTENANCE SCHEDULES 477 M • Check tire pressure and look for unusual wear or damage. Rotate tires at the first sign of irregular wear, even if it occurs before the oil indicator system turns on. • Check the fluid levels of the coolant reservoir, brake master cylinder, power steering and transmission (four-speed only) and fill as needed. • Check function of all interior and exterior lights.
8 Additional Inspections Inspect the CV joints. Inspect front suspension, tie rod ends, boot seals and replace if necessary. Inspect the brake linings, replace as necessary. Adjust parking brake as necessary.
Additional Maintenance Replace engine air filter. Replace cabin/air conditioning filter. Replace spark plugs (2.4L Engine). ** Replace spark plugs (2.4L PZEV Engine Only). ** Replace spark plugs (3.6L Engine).
S C H E D U L E S 8 Flush and replace the engine coolant at 10 years or 150,000 miles (240,000 km) whichever comes first. Change automatic transmission fluid and filter if using your vehicle for any of the following: police, taxi, fleet, or frequent trailer towing. Change automatic transmission fluid and filter. Inspect and replace PCV valve if necessary.
MAINTENANCE SCHEDULES 481 M ** The spark plug change interval is mileage based only, yearly intervals do not apply. WARNING! • You can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS 䡵 SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . .485 ▫ Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY). . . . . . . . . . . . . . . . . . .487 ▫ Prepare For The Appointment. . . . . . . . . . . . .485 ▫ Service Contract . . . . . . . . . . . . . . . . . . . . . .487 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . . .485 䡵 WARRANTY INFORMATION . . . . . . . . . . . . .
484 IF YOU NEED CONSUMER ASSISTANCE 䡵 DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES . . . . . . . . . . . . . . . . .491 ▫ Treadwear. . . . . . . . . . . . . . . . . . . . . . . . . . .491 ▫ Traction Grades . . . . . . . . . . . . . . . . . . . . . . .491 ▫ Temperature Grades. . . . . . . . . . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE 485 SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment Be Reasonable With Requests If you list a number of items and you must have your vehicle by the end of the day, discuss the situation with the service advisor and list the items in order of priority. At many authorized dealers, you may obtain a rental vehicle at a minimal daily charge. If you need a rental, it is advisable to make these arrangements when you call for an appointment.
486 IF YOU NEED CONSUMER ASSISTANCE facilities, factory-trained technicians, special tools, and • Authorized dealer name the latest information to ensure the vehicle is fixed • Vehicle Identification Number (VIN) correctly and in a timely manner. • Vehicle delivery date and mileage This is why you should always talk to an authorized dealer service manager first. Most matters can be re- Chrysler Group LLC Customer Center solved with this process. P.O.
IF YOU NEED CONSUMER ASSISTANCE 487 Mexico, D. F. Canadian residents with hearing difficulties that require assistance can use the special needs relay service offered by Bell Canada. For TTY teletypewriter users, dial 711 and for Voice callers, dial 1-800-855-0511 to connect with a Bell Relay Service operator.
488 IF YOU NEED CONSUMER ASSISTANCE The manufacturer will not stand behind any service contract that is not the manufacturer’s service contract. It is not responsible for any service contract other than the manufacturer’s service contract. If you purchased a service contract that is not a manufacturer’s service contract, and you require service after the manufacturer’s New Vehicle Limited Warranty expires, please refer to the contract documents, and contact the person listed in those documents.
IF YOU NEED CONSUMER ASSISTANCE 489 campaign. However, NHTSA cannot become involved in individual problems between you, your authorized MOPAR® fluids, lubricants, parts, and accessories are dealer, and the manufacturer. available from an authorized dealer. They are recommended for your vehicle in order to help keep the vehicle To contact NHTSA, you may either call the Auto Safety Hotline toll free at 1–888–327–4236 (TTY: 1–800–424– 9153), operating at its best. or go to http://www.safercar.
490 IF YOU NEED CONSUMER ASSISTANCE PUBLICATION ORDER FORMS To order the following manuals, you may use either the website or the phone numbers listed below. Visa, Mastercard, American Express, and Discover orders are accepted. If you prefer mailing your payment, please call for an order form. Diagnostic Procedure Manuals Diagnostic Procedure Manuals are filled with diagrams, charts and detailed illustrations.
IF YOU NEED CONSUMER ASSISTANCE 491 Call toll free at: Treadwear • 1–800–890–4038 (U.S.) The Treadwear grade is a comparative rating, based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half times as well on the government course as a tire graded 100.
492 IF YOU NEED CONSUMER ASSISTANCE WARNING! The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics. Temperature Grades The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel.
INDEX 10
494 INDEX About Your Brakes . . . . . . . . . . . . . . . . . . . . . . . .320 ABS (Anti-Lock Brake System) . . . . . . . . . . . . . . . .322 Adding Engine Coolant (Antifreeze) . . . . . . . . . . . .440 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .372 Adding Washer Fluid . . . . . . . . . . . . . . . . . . . . . .434 Additives, Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . .366 Airbag. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 495 Adding Fluid . . . . . . . . . . . . . . . . . . . . . . . . . .447 Fluid and Filter Changes . . . . . . . . . . . . . . . . . .450 Fluid Level Check . . . . . . . . . . . . . . . . . . . . . . .447 Fluid Type . . . . . . . . . . . . . . . . . . . . . . . . . . . .446 Gear Ranges . . . . . . . . . . . . . . . . . . . . . . . . . . .299 Special Additives . . . . . . . . . . . . . . . . . . . . . . .447 Autostick . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .314 Auto Unlock, Doors .
496 INDEX Cellular Phone . . . . . . . . . . . . . . . . . . . . . . . . . . .110 Certification Label. . . . . . . . . . . . . . . . . . . . . . . . .375 Chains, Tire . . . . . . . . . . . . . . . . . . . . . . . . . . . . .353 Changing A Flat Tire . . . . . . . . . . . . . . . . . . . . . . .395 Chart, Tire Sizing . . . . . . . . . . . . . . . . . . . . . . . . .333 Check Engine Light (Malfunction Indicator Light) . .422 Checking Your Vehicle For Safety . . . . . . . . . . . . . . .95 Checks, Safety . . .
INDEX 497 Dipsticks Automatic Transmission . . . . . . . . . . . . . . . . . .447 Oil (Engine) . . . . . . . . . . . . . . . . . . . . . . . . . . .425 Power Steering . . . . . . . . . . . . . . . . . . . . . . . . .319 Disabled Vehicle Towing . . . . . . . . . . . . . . . . . . . .414 Disposal Antifreeze (Engine Coolant) . . . . . . . . . . . . . . . .442 Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 Door Locks, Automatic . . . . . . . . . . . . . . . . . . . . . .
498 INDEX Electronic Vehicle Information Center (EVIC) . . . . . .224 Emergency, In Case of Jacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .395 Jump Starting . . . . . . . . . . . . . . . . . . . . . . . . . .407 Towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .414 Emergency Trunk Release . . . . . . . . . . . . . . . . . . . .41 Emission Control System Maintenance . . . . . . . . . .422 Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 499 Exterior Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . .99 Fabric Care. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .454 FCC General Information (Remote Keyless Entry) . . .27 FCC General Information (Sentry Key) . . . . . . . . . . .18 Filler Location Fuel . . . . . . . . . . . . . . . . . . . . . . . .208 Filters Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . .428 Air Conditioning . . . . . . . . . . . . . . . . . . . . . . .285 Engine Oil . . . . . .
500 INDEX Additives . . . . . . . . . Clean Air . . . . . . . . . Ethanol . . . . . . . . . . Filler Cap (Gas Cap) . Filler Door (Gas Cap) Gasoline . . . . . . . . . . Gauge . . . . . . . . . . . Light . . . . . . . . . . . . Materials Added . . . . Methanol . . . . . . . . . Octane Rating . . . . . . Requirements . . . . . . Tank Capacity . . . . . . Fuel, Flexible . . . . . . . . Fueling . . . . . . . . . . . . Fuel System Caution . . . Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 501 Hands-Free Phone (Uconnect®) . . . . . . . . . . . . Hazard Driving Through Flowing, Rising, or Shallow Standing Water . . . . . . . . . . . . . . . . . . . . . . Hazard Warning Flasher . . . . . . . . . . . . . . . . . Headlights . . . . . . . . . . . . . . . . . . . . . . . . . . . Bulb Replacement . . . . . . . . . . . . . . . . . . . . Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . High Beam . . . . . . . . . . . . . . . . . . . . . . . . . High Beam/Low Beam Select Switch . . .
502 INDEX Interior Lights . . . . . . . . . . . . . . . . . . . . . . . . . . .168 Intermittent Wipers (Delay Wipers). . . . . . . . . . . . .170 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 iPod®/USB/MP3 Control Bluetooth® Streaming Audio . . . . . . . . . . . . . . .144 Jacking Instructions . Jack Location . . . . . Jack Operation . . . . Jump Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 503 Electronic Stability Program (ESP) Indicator . . . . .330 Engine Temperature Warning . . . . . . . . . . . . . . .210 Exterior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99 Fog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .166 Headlights . . . . . . . . . . . . . . . . . . . . . . . . . . . .163 Headlights On With Wipers . . . . . . . . . . . . . . . .164 Headlight Switch . . . . . . . . . . . . . . . . . . . . . . .163 High Beam Indicator . . . . . . . . . .
504 INDEX Lumbar Support . . . . . . . . . . . . . . . . . . . . . . . . . .153 Monitor, Tire Pressure System . . . . . . . . . . . . . . . .355 Mopar Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . .423 Maintenance Free Battery. . . . . . . . . . . . . . . . . . . .429 MTBE/ETBE . . . . . . . . . . . . . . . . . . . . . . . . . . . .365 Maintenance Procedures . . . . . . . . . . . . . . . . . . . .424 Maintenance Schedule . . . . . . . . . . . . . . . . . . . . . .
INDEX 505 Personal Settings. . . . . . . . . . . . . . . . . . . . . . . . . .233 Pets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94 Phone, Cellular . . . . . . . . . . . . . . . . . . . . . . . . . . .110 Phone, Hands-Free (Uconnect®) . . . . . . . . . . . . . . .110 Placard, Tire and Loading Information . . . . . . . . . .338 Power Deck Lid Release . . . . . . . . . . . . . . . . . . . . . . . .40 Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . .32 Mirrors . .
506 INDEX Programmable Electronic Features . . . . . . . . . . . . .233 Remote Keyless Entry (Sedan) . . . . . . . . . . . . . . . . .22 Remote Sound System (Radio) Controls . . . . . . . . .270 Radial Ply Tires . . . . . . . . . . . . . . . . . . . . . . . . . .345 Remote Starting System. . . . . . . . . . . . . . . . . . . . . .28 Radiator Cap (Coolant Pressure Cap) . . . . . . . . . . .441 Remote Trunk Release. . . . . . . . . . . . . . . . . . . . . . .40 Radio Operation . . . . . . . . . . . . . . . .
INDEX 507 Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95 Satellite Radio Antenna . . . . . . . . . . . . . . . . . . . . .260 Schedule, Maintenance . . . . . . . . . . . . . . . . . . . . .476 Seat Belt Maintenance . . . . . . . . . . . . . . . . . . . . . .455 Seat Belt Reminder . . . . . . . . . . . . . . . . . . . . . . . . .57 Seat Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96 Adjustable Shoulder Belt . . . . . . . . . . . . . . . . . . .
508 INDEX Side Window Demisters (Defrosters) . . . . . . . . . . . .284 Signals, Turn . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99 Snow Chains (Tire Chains) . . . . . . . . . . . . . . . . . . .353 Snow Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .346 Spare Tire. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .348 Speed Control (Cruise Control). . . . . . . . . . . . . . . .174 Speedometer. . . . . . . . . . . . . . . . . . . . . . . . . . . . .208 Starting . .
INDEX 509 Chains . . . . . . . . . . . . . . . . . . . Changing . . . . . . . . . . . . . . . . . Compact Spare . . . . . . . . . . . . . General Information . . . . . . . . . High Speed . . . . . . . . . . . . . . . Inflation Pressures . . . . . . . . . . . Jacking . . . . . . . . . . . . . . . . . . . Life of Tires . . . . . . . . . . . . . . . Load Capacity . . . . . . . . . . . . . Pressure Monitor System (TPMS) Pressure Warning Light . . . . . . . Quality Grading . . . . . . . . . . . . Radial . . . .
510 INDEX Trailer and Tongue Weight . . . . . . . . . . . . . . . . .381 Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .386 Trailer Towing Guide. . . . . . . . . . . . . . . . . . . . . . .380 Trailer Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . .380 Transaxle Automatic . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 Autostick . . . . . . . . . . . . . . . . . . . . . . . . . . . . .314 Transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 511 Uconnect® (Hands-Free Phone) . . . . . . . . . . . . . . .110 Understanding Your Instrument Panel. . . . . . . . . . .206 Uniform Tire Quality Grades . . . . . . . . . . . . . . . . .491 Universal Consumer Interface (UCI) Connector . . . .263 Unleaded Gasoline . . . . . . . . . . . . . . . . . . . . . . . .364 Untwisting Procedure, Seat Belt . . . . . . . . . . . . . . . .50 Upholstery Care . . . . . . . . . . . . . . . . . . . . . . . . . .454 Vanity Mirrors . . . . . . . . . . . . . . . . . . .
512 INDEX Windshield Washers . . . . Fluid . . . . . . . . . . . . . Windshield Wiper Blades . Windshield Wipers . . . . . Wiper Blade Replacement Wipers, Intermittent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .169 .434 .434 .169 .434 .
INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained personnel. The following must be observed during installation. The positive power connection should be made directly to the battery and fused as close to the battery as possible.
2014 200 2014 OWNER’S MANUAL Chrysler Group LLC 14C41-126-AC Third Edition Printed in U.S.A.
