2013 OWNER’S MANUAL Town & Country
VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name Chrysler Group LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefore. DRIVING AND ALCOHOL Drunken driving is one of the most frequent causes of accidents. This manual illustrates and describes the operation of features and equipment that are either standard or optional on this vehicle.
SECTION TABLE OF CONTENTS PAGE 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127 3 4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION CONTENTS 䡵 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . .4 䡵 VEHICLE IDENTIFICATION NUMBER . . . . . . . .6 䡵 HOW TO USE THIS MANUAL . . . . . . . . . . . . . .4 䡵 VEHICLE MODIFICATIONS/ALTERATIONS . . . .7 䡵 WARNINGS AND CAUTIONS . . . . . . . . . . . . . .
4 INTRODUCTION When it comes to service, remember that your authorized Congratulations on selecting your new Chrysler Group dealer knows your vehicle best, has factory-trained techLLC vehicle. Be assured that it represents precision work- nicians and genuine parts, and cares about your satisfacmanship, distinctive styling, and high quality - all essen- tion. tials that are traditional to our vehicles.
INTRODUCTION 5 1
6 INTRODUCTION WARNINGS AND CAUTIONS This Owners Manual contains WARNINGS against operating procedures that could result in a collision or bodily injury. It also contains CAUTIONS against procedures that could result in damage to your vehicle. If you do not read this entire Owners Manual, you may miss important information. Observe all Warnings and Cautions.
INTRODUCTION 7 VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death. Stamped VIN Location NOTE: It is illegal to remove or alter the VIN.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS 䡵 A WORD ABOUT YOUR KEYS . . . . . . . . . . . . .12 䡵 REMOTE STARTING SYSTEM — IF EQUIPPED . .30 ▫ Wireless Ignition Node (WIN) . . . . . . . . . . . . .12 ▫ How To Use Remote Start . . . . . . . . . . . . . . . .30 䡵 SENTRY KEY® . . . . . . . . . . . . . . . . . . . . . . . . .15 䡵 DOOR LOCKS . . . . . . . . . . . . . . . . . . . . . . . . .35 ▫ Replacement Keys . . . . . . . . . . . . . . . . . . . . .16 ▫ Manual Door Locks . . . . . . . . . . .
10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 䡵 SLIDING SIDE DOOR . . . . . . . . . . . . . . . . . . . .48 ▫ Supplemental Active Head Restraints (AHR) . . .73 ▫ Power Sliding Side Door — If Equipped . . . . . .49 ▫ Enhanced Seat Belt Use Reminder System (BeltAlert®) . . . . . . . . . . . . . . . . . . . . . . . . . .77 ▫ Sliding Side Door Child Protection Lock . . . . . .53 䡵 LIFTGATE . . . . . . . . . . . . . . . . . . . . . . . . . . . .56 ▫ Power Liftgate — If Equipped . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 䡵 COMMERCIAL CARGO VEHICLES (NO FACTORY INSTALLED REAR SEATS) — IF EQUIPPED. . . . . . . . . . . . . . . . . . . . . . . . . .117 ▫ Restraining Infants And Small Children In Commercial Cargo Vehicles. . . . . . . . . . . . . . .118 䡵 ENGINE BREAK-IN RECOMMENDATIONS . . .120 䡵 SAFETY TIPS . . . . . . . . . . . . . . . . . . . . . . . . .120 ▫ Transporting Passengers . . . . . . . . . . . . . . . . .120 ▫ Exhaust Gas . . . . . . . . . . . . . . . . . . . . . .
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS Your vehicle uses a keyless ignition system. This system consists of a Key Fob with Remote Keyless Entry (RKE) transmitter and a Keyless Ignition Node (KIN). Keyless Enter-N-Go™ Feature This vehicle is equipped with the Keyless Enter-N-Go™ feature, (refer to ⬙Keyless Enter-N-Go™⬙ in ⬙Things To Know Before Starting Your Vehicle⬙ for further information).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 Key Fob The Key Fob operates the ignition switch. Insert the square end of the key fob into the ignition switch located on the instrument panel and rotate to the desired position. It also contains the Remote Keyless Entry (RKE) transmitter and an emergency key, which stores in the rear of the Key Fob. The emergency key allows for entry into the vehicle should the battery in the vehicle or the RKE transmitter go dead.
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Power window switches will also remain active for up to 10 minutes after the ignition switch has been turned to OFF, depending upon the accessory delay setting. Opening the front door will cancel this feature. WARNING! (Continued) • Do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. WARNING! • Never leave children alone in a vehicle, or with access to an unlocked vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 After turning the ignition switch to the ON/RUN position, the Vehicle Security Light will turn on for three seconds for a bulb check. If the light remains on after the bulb check, it indicates that there is a problem with the electronics. In addition, if the light begins to flash after the bulb check, it indicates that someone used an invalid SENTRY KEY® Key Fob to start the engine.
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE At the time of purchase, the original owner is provided with a four-digit Personal Identification Number (PIN). Use of these systems may result in vehicle starting Keep the PIN in a secure location. This number is problems and loss of security protection. required for authorized dealer replacement of Key Fobs.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 and/or turn signals will flash and Vehicle Security Light will flash repeatedly and the horn will sound. For an The Sentry Key® system complies with FCC rules Part 15 additional 15 minutes, only the headlights, park lamps and with RSS-210 of Industry Canada. Operation is and/or turn signals and Vehicle Security Light will flash. subject to the following conditions: Rearming Of The System • This device may not cause harmful interference.
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • For vehicles equipped with Keyless Enter-N-Go™, To Disarm The System make sure the vehicle ignition system is ⬙OFF⬙. The Vehicle Security Alarm can be disarmed using any of • For vehicles not equipped with Keyless Enter-N-Go™, the following methods: make sure the vehicle ignition system is ⬙OFF⬙ and the • Press the UNLOCK button on the Remote Keyless key is physically removed from the ignition. Entry (RKE) transmitter. 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 you are in the vehicle or not. If you remain in the vehicle and open a door, the alarm will sound. If this occurs, • The driver’s door key cylinder and the liftgate button disarm the Vehicle Security Alarm. on the RKE transmitter cannot arm or disarm the Vehicle Security Alarm.
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The illuminated entry system will not operate if the dimmer control is in the “Dome OFF” position (rotate The courtesy lights will turn on when you use the horizontal thumb wheel on the bottom of the switch to Remote Keyless Entry (RKE) transmitter to unlock the the far left detent position). doors or open any door. ILLUMINATED ENTRY — IF EQUIPPED This feature also turns on the approach lighting in the outside mirrors (if equipped).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 at speeds 5 mph (8 km/h) and above disables the system from responding to all RKE transmitter buttons for all RKE transmitters. 2 Two RKE transmitters may be supplied with the vehicle. Vehicles built without the powered options will be equipped from the factory with three-button RKE transmitters, and those built with power options will be equipped with up to seven-button RKE transmitters.
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seven-button RKE transmitters will provide functions that allow the same basic operation as the three-button, but may also be used to operate the power liftgate (optional), power sliding doors, Remote Start feature (optional). Some features can be programmed to the customers preferences. For example, flash headlights or sound horn on LOCK.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 • For vehicles not equipped with the EVIC, the Remote 5. Repeat these steps if you want to return this feature to Unlock feature can be enabled or disabled by performits previous setting. ing the following steps: NOTE: Pressing the LOCK button on the RKE transmit1. Perform this operation while standing outside the ter while you are inside the vehicle will activate the vehicle. Vehicle Security Alarm.
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Sound Horn With Remote Lock 3. Release both buttons at the same time. This feature will cause the horn to chirp when the doors 4. Test the feature while outside of the vehicle by pressare locked with the RKE transmitter. This feature can be ing the LOCK button on the RKE transmitter with the turned on or turned off. To change the current setting, ignition switch in the OFF position and the Key Fob proceed as follows: removed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 Using The Panic Alarm Power Open/Close Power Liftgate — If Equipped To turn the Panic Alarm feature on or off, press and hold the PANIC button on the RKE transmitter for at least one second and release. When the Panic Alarm is on, the headlights and park lights will flash, the horn will pulse on and off, and the interior lights will turn on. Press the LIFTGATE button twice on the RKE transmitter within five seconds to Open/Close the Power Liftgate.
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Power Open/Close Left Power Sliding Door — If Equipped power-closed, the door will reverse to the full open position. Press the LEFT Power Sliding Door button twice on the RKE transmitter within five seconds to Power Open/Close the Left Power Sliding Door. If the button on the RKE transmitter is pushed while the door is being power-closed, the door will reverse to the full open position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 • For vehicles not equipped with the EVIC, perform the NOTE: Pressing the LOCK button on the RKE transmitter following steps: while you are in the vehicle will activate the Vehicle Security Alarm. Opening a door with the Vehicle Security 1. Perform this operation while standing outside the Alarm activated will cause the alarm to sound. Press the vehicle. UNLOCK button to deactivate the Vehicle Security Alarm. 2.
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 1. Remove the emergency key by sliding the mechanical 2. Insert the tip of the emergency key or a #2 flat blade latch at the top of the RKE transmitter sideways with screwdriver into the slot and gently pry the two halves your thumb and then pull the key out with your other of the RKE transmitter apart. Make sure not to damage hand. the seal during removal.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 3. Remove and replace the battery. When replacing the battery, match the + sign on the battery to the + sign on the inside of the battery clip, located on the back cover. Avoid touching the new battery with your fingers. Skin oils may cause battery deterioration. If you touch a battery, clean it with rubbing alcohol. 4. To assemble the RKE transmitter case, snap the two halves together.
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE REMOTE STARTING SYSTEM — IF EQUIPPED How To Use Remote Start This system uses the Remote Keyless Entry (RKE) transmitter to start the engine conveniently from outside the vehicle while still maintaining security. The system has a range of approximately 300 ft (91 m).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 • System not disabled from previous remote start event Remote Start Abort Message On Electronic Vehicle Information Center (EVIC) — If Equipped • Vehicle theft alarm not active The following messages will display in the EVIC if the • Ignition in Off position (Keyless Enter-N-Go™) vehicle fails to remote start or exits remote start prematurely: WARNING! • Do not start or run an engine in a closed garage or confined area.
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Enter Remote Start Mode • The engine can be started times (two 15 minutes cycles) with the RKE transmitter. However, the ignition switch must be cycled by pushing the START/STOP button twice (or the ignition switch must be cycled to the ON/RUN position). Press and release the REMOTE START button on the RKE transmitter twice within five seconds. The vehicle doors will lock, the parking lights will flash and horn will chirp twice (if programmed).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 • For vehicles not equipped with the Keyless Enter-NGo™ feature, the ignition switch must be in the Before the end of the 15-minute cycle, press and release the ON/RUN position in order to drive the vehicle. UNLOCK button on the RKE transmitter to unlock the doors and disarm the Vehicle Security Alarm (if equipped).
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Cancel Remote Start To Turn Off The Engine While In Remote Start Mode Remote Starting will also cancel if any of the following Press and release the REMOTE START button one time or occur: allow the engine to run for the entire 15 minute cycle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 DOOR LOCKS Manual Door Locks Lock the front doors by pushing down on the lock knobs on each door trim panel. 2 If the lock knob is down when you shut either front door, the door will lock. Make sure the keys are not inside the vehicle before closing the door.
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If the lock knob is rearward when you shut either side sliding door, the door will lock. Make sure the keys are not inside the vehicle before closing the door. Sliding Door Lock WARNING! • For personal security and safety in the event of a collision, lock the vehicle doors as you drive as well as when you park and leave the vehicle. • When leaving the vehicle, always remove the Key Fob from the ignition and lock your vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 WARNING! (Continued) • Do not leave the Key Fob in or near the vehicle, or in a location accessible to children, and do not leave a vehicle equipped with Keyless Enter-NGo™ in the ACC or ON/RUN mode. A child could operate power windows, other controls, or move the vehicle. 2 Power Door Locks — If Equipped A power door lock switch is on each front door trim panel. Use this switch to lock or unlock the doors.
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE will sound if the Key Fob is in the ignition switch and a If you press the power door lock switch while the sliding door is open, as a reminder to remove the Key Fob. door is open, the sliding door will lock. Automatic Door Locks — If Equipped When enabled, the door locks will lock automatically when the vehicle’s speed exceeds 15 mph (24 km/h). The auto door lock feature can be enabled or disabled by your authorized dealer per written request of the customer.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 The Unlock Doors Automatically On Exit feature will not NOTE: operate if there is any manual operation of the power • Passive Entry may be programmed ON/OFF; refer to door locks (lock or unlock). “Electronic Vehicle Information Center (EVIC)/Personal Settings (Customer-Programmable Features)” in “UnderOn vehicles equipped with the optional Electronic standing Your Instrument Panel” for further information.
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Unlock From The Driver’s Side: With a valid Passive Entry RKE transmitter within 5 ft (1.5 m) of the driver’s door handle, grab the driver’s front door handle to unlock the driver’s door automatically. The interior door panel lock knob will raise when the door is unlocked. NOTE: If “Unlock All Doors 1st Press” is programmed all doors will unlock when you grab hold of the driver’s front door handle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 Preventing Inadvertent Locking Of Passive Entry RKE To Enter The Liftgate Transmitter In Vehicle With a valid Passive Entry RKE transmitter within 5 ft To minimize the possibility of unintentionally locking a (1.5 m) of the liftgate, cycle the handle to open the liftgate Passive Entry RKE transmitter inside your vehicle, the and pull the liftgate open with one fluid motion.
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Lock The Vehicle’s Doors With one of the vehicle’s Passive Entry RKE transmitters within 5 ft (1.5 m) of the driver or passenger front door handle, press the door handle LOCK button to lock all four doors. Do NOT grab the door handle, when pressing the door handle lock button. This could unlock the door(s).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 NOTE: WINDOWS • After pressing the door handle LOCK button, you must wait two seconds before you can lock or unlock the doors, using either Passive Entry door handle. This is done to allow you to check if the vehicle is locked by pulling the door handle, without the vehicle reacting and unlocking.
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Power Window switches will also remain active You can control either the front or rear windows using for up to 10 minutes after the ignition switch has been switches located on the driver’s door trim panel. The turned to OFF, depending upon the accessory delay setting. Opening a front door will cancel this feature.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 The switches will operate only when the ignition switch is in the ON/RUN or ACC position and during power accessory delay. 2 Power Window Lockout Switch Front Passenger Power Window Switch There is a single switch on the front passenger’s door Front Passenger Power Door Switches trim panel which operates the passenger door window 1 - Window Open/Close and a set of switches that lock and unlock all doors.
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Auto-Down Feature — If Equipped To stop the window from going all the way up during the Auto Up operation, push down on the switch briefly. The front window switches may be equipped with an AutoDown feature. Press the window switch past the detent, To close the window part way, lift the window switch to release, and the window will go down automatically. the first detent and release when you want the window to stop.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 WARNING! There is no anti-pinch protection when the window is almost closed. To avoid personal injury be sure to clear your arms, hands, fingers and all objects from the window path before closing. Sliding Side Door Power Window Switch — If Equipped Second row passengers may open and close the sliding door window by a single switch on the door handle assembly.
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: The switches will not operate if the driver has Wind Buffeting activated the Power Window Lockout. Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occurrence and can be minimized.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 To keep your door operating properly, observe the fol- NOTE: The left side sliding door cannot be opened lowing guidelines: while the fuel door is open. This feature operates only when the sliding door is fully closed prior to opening the • Always open the door smoothly. fuel door. • Avoid high impacts against the door stop when opening the door.
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Press the button on the RKE transmitter twice within 5 seconds to open a power sliding door. When the door is fully open, pressing the button twice within 5 seconds a second time will close the door. There are power sliding side door switches located on the b-pillar trim panel, just in front of the power sliding door for the rear seat passengers and in the overhead console for the driver and passengers.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 To avoid unintentional operation of the power sliding • If the power sliding side door is not in the full open or close position, it will fully open when a power sliding doors from the rear seats, press the power sliding door door switch is pressed. To close the door, wait until it master lock button, located in the overhead console, is fully open and then press the switch again. to disable the switches and handles for the rear seat passengers.
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE You can turn the feature back on by repeating the previous The left and right exterior hazard lights will flash for procedure. 12 seconds when either sliding door is opened. This will Power Sliding Side Door Master Lock Switch alert other drivers in the area that passenger(s) could be To provide a safer environment for small children riding entering or exiting the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 Sliding Side Door Child Protection Lock To provide a safer environment for small children riding in the rear seats, the sliding doors are equipped with a Child Protection Door Lock system. NOTE: When the Child Protection Door Lock system is engaged, the door can be opened only by using the outside door handle even though the inside door lock is in the unlocked position.
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Engage the Child Protection Door Lock 3. Repeat Steps 1 and 2 on the opposite sliding door. 1. Open the sliding side door. NOTE: 2. Slide the Child Protection Door Lock control inward • After engaging the Child Protection Door Lock, always test the door from the inside to make certain it is in the (toward the vehicle) to engage the Child Protection desired position. Door Lock.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 WARNING! Avoid trapping anyone in the vehicle in a collision. Remember that the sliding doors can only be opened from the outside door handle or the switches located on the trim panel just in front of the power sliding door when the Child Protection Door Locks are engaged. NOTE: • After setting the Child Protection Door Lock system, always test the door from the inside to make certain it is in the desired position.
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE LIFTGATE On vehicles equipped with power locks, the liftgate can be unlocked using the Remote Keyless Entry (RKE) transmitter button, or by activating the power door lock switches located on the front doors. To open the liftgate, press the liftgate release handle located on the underside of the license plate bar and pull the liftgate open with one fluid motion.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 Power Liftgate — If Equipped The power liftgate may be opened manually or by using the button on the Remote Keyless Entry (RKE) transmitter. Press the button on the transmitter twice within five seconds, to open the power liftgate. When the liftgate is fully open, pressing the button twice within five seconds, a second time, will close the liftgate. 2 The power liftgate may also be opened and closed by pressing the button located on the overhead console.
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The power liftgate may be closed by pressing the button, located in the upper left trim in the liftgate opening. Pushing once will only close the liftgate. This button cannot be used to open the liftgate. When the RKE transmitter button is pressed and the Flash Lights feature is enabled, the tail lights will flash and several audible beeps will occur to signal that the liftgate is opening or closing.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 • There are also pinch sensors attached to the side of the • The power liftgate buttons will not operate if the shift liftgate opening. Light pressure anywhere along these lever is in gear or the vehicle speed is above 0 mph strips will cause the liftgate to return to the open (0 km/h). position. • The power liftgate will not operate in temperatures below −12°F (−24°C) or temperatures above 143°F • During power operation, whether liftgate is fully open (62°C).
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Driving with the liftgate open can allow poisonous exhaust gases into your vehicle. You and your passengers could be injured by these fumes. Keep the liftgate closed when you are operating the vehicle. • If you are required to drive with the liftgate open, make sure that all windows are closed, and the climate control blower switch is set at high speed. Do not use the recirculation mode.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 • An energy-absorbing steering column and steering wheel If you will be carrying children too small for adult-sized seat belts, the seat belts or the Lower Anchors and Tether • Knee bolster for front passenger seat occupant for CHildren (LATCH) feature also can be used to hold • Front seat belts incorporate pretensioners that may infant and child restraint systems.
62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Infants in rear facing child restraints should never ride in the front seat of a vehicle with a passenger Advanced Front Air Bag. An air bag deployment can cause severe injury or death to infants in that position. If a child from 1 to 12 years old (not in a rear facing child seat) must ride in the front passenger seat, move the seat as far back as possible and use the proper child restraint.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 5. If the air bag system in this vehicle needs to be modified to accommodate a disabled person, contact the Customer Center. Phone numbers are provided under ⴖIf You Need Assistanceⴖ. WARNING! • Relying on the air bags alone could lead to more severe injuries in a collision. The air bags work with your seat belt to restrain you properly. In some collisions, the air bags won’t deploy at all. Always wear your seat belts even though you have air bags.
64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Buckle up even though you are an excellent driver, even Lap/Shoulder Belts on short trips. Someone on the road may be a poor driver All seats in your vehicle are equipped with lap/shoulder and cause a collision that includes you. This can happen belts. far away from home or on your own street. The belt webbing in the retractor is designed to lock Research has shown that seat belts save lives, and they during very sudden stops or collisions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 WARNING! (Continued) WARNING! (Continued) • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • Be sure everyone in your vehicle is in a seat and using a seat belt properly. • Wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and can take the forces of a collision the best.
66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Pulling Out Belt And Latch Plate • A belt that is worn under your arm is dangerous. Your body could strike the inside surfaces of the vehicle in a collision, increasing head and neck injury. A belt worn under the arm can cause internal injuries. Ribs aren’t as strong as shoulder bones. Wear the belt over your shoulder so that your strongest bones will take the force in a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 WARNING! • A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you properly. In a sudden stop you could move too far forward, increasing the possibility of injury. Wear your seat belt snugly. Inserting Latch Plate Into Buckle 4.
68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as possible and keep it snug. • A twisted belt may not protect you properly. In a collision, it could even cut into you. Be sure the belt is straight.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 6. To release the belt, push the red button on the buckle. Third Row Center Shoulder Belt Instructions The belt will automatically retract to its stowed posi- The shoulder belt for the third row center seat is located tion. If necessary, slide the latch plate down the in the headliner slightly behind the third row seat. webbing to allow the belt to retract fully.
70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Adjustable Upper Shoulder Belt Anchorage In the front seats and the second row outboard seats, the shoulder belt anchorage can be adjusted upward or downward to help position the belt away from your neck. The upper anchorage can be adjusted upward by pushing anywhere on the anchorage. To move the anchorage downward, squeeze the actuation buttons while simultaneously pushing down on the anchorage assembly.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 If the passenger seating position is equipped with an The seat belts in the passenger seating positions are ALR and is being used for normal usage: equipped with an Automatic Locking Retractor (ALR) or Only pull the belt webbing out far enough to comfortably a cinching latch plate which are used to secure a child wrap around the occupant’s mid-section so as to not restraint system. For additional information refer to activate the ALR.
72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Automatic Locking Retractor Mode (ALR) — If Equipped How To Disengage The Automatic Locking Mode Unbuckle the combination lap/shoulder belt and allow it In this mode, the shoulder belt is automatically pre-locked. to retract completely to disengage the Automatic Locking The belt will still retract to remove any slack in the Mode and activate the vehicle sensitive (emergency) shoulder belt. The Automatic Locking Mode is available on locking mode.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 Energy Management Feature This vehicle has a safety belt system with an Energy Management feature in the front seating positions to help further reduce the risk of injury in the event of a head-on collision. NOTE: These devices are not a substitute for proper seat belt placement by the occupant. The seat belt still must be worn snugly and positioned properly. The pretensioners are triggered by the Occupant Restraint Controller (ORC).
74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE How The Active Head Restraints (AHR) Work The Occupant Restraint Controller (ORC) determines whether the severity, or type of rear impact will require the Active Head Restraints (AHR) to deploy. If a rear impact requires deployment, both the driver and front passenger seat AHRs will be deployed. When AHRs deploy during a rear impact, the front half of the head restraint extends forward to minimize the gap between the back of the occupant’s head and the AHR.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 CAUTION! 1. Grasp the deployed AHR from the rear seat. All occupants, including the driver, should not operate a vehicle or sit in a vehicle’s seat until the head restraints are placed in their proper positions in order to minimize the risk of neck injury in the event of a collision. NOTE: For more information on properly adjusting and positioning the head restraint, refer to “Adjusting Active Head Restraints” in “Understanding The Features Of Your Vehicle”.
76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Pull down then rearward towards the rear of the vehicle then down to engage the locking mechanism. 3 — Final Downward Movement To Engage Locking Mechanism 1 — Downward Movement 2 — Rearward Movement 4. The AHR front soft foam and trim half should lock into the back decorative plastic half.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77 Enhanced Seat Belt Use Reminder System (BeltAlert®) BeltAlert® is a feature intended to remind the driver and front passenger (if equipped with front passenger BeltAlert®) to fasten their seat belts. The feature is active whenever the ignition is on. If the driver or front seat passenger is unbelted, the Seat Belt Reminder Light will turn on and remain on until both front seat belts are fastened.
78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE unbuckled while traveling at speeds greater than 5 mph Seat Belts And Pregnant Women (8 km/h), BeltAlert® will provide both audio and visual We recommend that pregnant women use the seat belts notification. throughout their pregnancy. Keeping the mother safe is The front passenger seat BeltAlert® is not active when the best way to keep the baby safe. the front passenger seat is unoccupied.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 79 WARNING! Using a seat belt extender when not needed can increase the risk of injury in a collision. Only use when the seat belt is not long enough when it is worn low and snug and in the recommended seating positions. Remove and store the extender when not needed. 2 Supplemental Restraint System (SRS) — Air Bags This vehicle has Advanced Front Air Bags for both the driver and front passenger as a supplement to the seat belt restraint systems.
80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: These air bags are certified to the new Federal This vehicle is equipped with Supplemental Side Air Bag regulations for Advanced Air Bags. Inflatable Curtains (SABIC) to protect the driver, front, and rear passengers sitting next to a window. The SABIC The Advanced Front Air Bags have a multistage inflator air bags are located above the side windows and their design. This allows the air bag to have different rates of covers are also labeled: SRS AIRBAG.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 81 Air Bag System Components • Front and Side Impact Sensors Your vehicle may be equipped with the following air bag • Front Seat Belt Pretensioners, Seat Belt Buckle Switch, system components: and Seat Track Position Sensors • Occupant Restraint Controller (ORC) Advanced Front Air Bag Features • Air Bag Warning Light The Advanced Front Air Bag system has multistage driver and front passenger air bags.
82 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • No objects should be placed over or near the air bag on the instrument panel, because any such objects could cause harm if the vehicle is in a collision severe enough to cause the air bag to inflate. • Do not put anything on or around the air bag covers or attempt to open them manually. You may damage the air bags and you could be injured because the air bags may no longer be functional.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 83 When the air bag deploys, it opens the seam between the NOTE: front and side of the seat’s trim cover. Each air bag • Should a vehicle rollover occur, the pretensioners deploys independently; a left side impact deploys the left and/or SAB and SABIC air bags on both sides of the air bag only and a right-side impact deploys the right air vehicle may deploy. bag only.
84 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! (Continued) • Your vehicle is equipped with left and right Supplemental Side Air Bag Inflatable Curtain (SABIC), do not stack luggage or other cargo up high enough to block the location of the SABIC. The area where the SABIC is located should remain free from any obstructions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 85 Supplemental Driver Side Knee Air Bag Air Bag Deployment Sensors And Controls The Supplemental Driver Side Knee Air Bag provides Occupant Restraint Controller (ORC) enhanced protection and works together with the Driver The ORC is part of a Federally regulated safety system Advanced Front Air Bag during a frontal impact. required for this vehicle.
86 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE severity and type of collision. Advanced Front Air Bags Seat belts are necessary for your protection in all colliare not expected to reduce the risk of injury in rear, side, sions, and also are needed to help keep you in position, or rollover collisions. away from an inflating air bag.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 87 turns on the Air Bag Warning Light, either momentarily Driver And Passenger Advanced Front Air Bag or continuously. A single chime will sound if the light Inflator Units comes on again after initial startup.
88 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The Advanced Front Air Bag gas is vented through the Supplemental Seat-Mounted Side Air Bag (SAB) vent holes in the sides of the air bag. In this way, the air Inflator Units bags do not interfere with your control of the vehicle. The Supplemental Seat-Mounted Side Air Bags (SAB) are designed to activate only in certain side collisions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 89 you if you are not seated properly, or if items are blink your eyes) with enough force to injure you if you positioned in the area where the side air bag inflates. are not belted and seated properly, or if items are positioned in the area where the side curtain air bag This especially applies to children. inflates. This especially applies to children.
90 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Enhanced Accident Response System If A Deployment Occurs In the event of an impact causing air bag deployment, if the communication network remains intact, and the power remains intact, depending on the nature of the event the ORC will determine whether to have the Enhanced Accident Response System perform the following functions: The Advanced Front Air Bags are designed to deflate immediately after deployment. Cut off fuel to the engine.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 91 They are not caused by contact with chemicals. They are Do not drive your vehicle after the air bags have denot permanent and normally heal quickly. However, if ployed. If you are involved in another collision, the air you haven’t healed significantly within a few days, or if bags will not be in place to protect you. you have any blistering, see your doctor immediately. As the air bags deflate, you may see some smoke-like particles.
92 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Maintaining Your Air Bag System WARNING! (Continued) WARNING! • Modifications to any part of the air bag system could cause it to fail when you need it. You could be injured if the air bag system is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the steering wheel hub trim cover or the upper right side of the instrument panel.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 93 Air Bag Warning Light You will want to have the air bags ready to inflate for your protection in a collision. The Air Bag Warning Light monitors the internal circuits and interconnecting wiring associated with air bag system electrical components. While the air bag system is designed to be maintenance free, if any of the following occurs, have an authorized dealer service the air bag system immediately.
94 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Event Data Recorder (EDR) This vehicle is equipped with an event data recorder (EDR). The main purpose of an EDR is to record, in certain crash or near crash-like situations, such as an air bag deployment or hitting a road obstacle, data that will assist in understanding how a vehicle’s systems performed. The EDR is designed to record data related to vehicle dynamics and safety systems for a short period of time, typically 30 seconds or less.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 95 Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Everyone in your vehicle needs to be buckled up at all Standards. You should also make sure that you can install times, including babies and children. Every state in the it in the vehicle where you will use it. United States, and every Canadian province, requires that small children ride in proper restraint systems.
96 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Summary Of Recommendations For Restraining Children In Vehicles Infants and Toddlers Small Children Larger Children Children Too Large for Child Restraints Child Size, Height, Weight or Age Children who are two years old or younger and who have not reached the height or weight limits of their child restraint Children who are at least two years old or who have out-grown the height or weight limit of their rear-facing child restraint Children who have out-g
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 97 their infant carrier but are still less than at least two years old. Children should remain rearward-facing until they Safety experts recommend that children ride rearwardreach the highest weight or height allowed by their facing in the vehicle until they are two years old or until convertible child seat. they reach either the height or weight limit of their rear facing child safety seat.
98 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE the seatback, they should use a belt-positioning booster seat. The child and belt-positioning booster seat are held Children who are two years old or who have outgrown in the vehicle by the seat belt. their rear-facing convertible child seat can ride forwardfacing in the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 99 4. Is the lap part of the belt as low as possible, touching the child’s thighs and not their stomach? Children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend 5. Can the child stay seated like this for the whole trip? over the front of the seat when their back is against the seatback, should use the seat belt in a rear seat.
100 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Recommendations For Attaching Child Restraints Restraint Type Combined Weight of the Child + Child Restraint Rear-Facing Child Restraint Rear-Facing Child Restraint Forward-Facing Child Restraint Forward-Facing Child Restraint Up to 65 lbs (29.5 kg) More than 65 lbs (29.5 kg) Up to 65 lbs (29.5 kg) More than 65 lbs (29.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 101 Lower Anchors and Tethers for Children (LATCH) Restraint System Your vehicle is equipped with the child restraint anchorage system called LATCH, which stands for Lower Anchors and Tethers for CHildren. The LATCH system has three vehicle anchor points for installing LATCHequipped child seats. There are two lower anchorages located at the back of the seat cushion where it meets the seatback and one top tether anchorage located behind the seating position.
102 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE LATCH Positions For Installing Child Restraints In This Vehicle Second Row Captains Chairs Second Row Bench Lower Anchorage Symbol 2 anchorages per seating Lower Anchorage Symbol 2 anchorages per seating position position Top Tether Anchorage Symbol Top Tether Anchorage Symbol
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 103 Child Restraint LATCH Positions What is the weight limit (child’s weight + weight of the child restraint) for using the LATCH anchorage system to attach the child restraint? 65 lbs (29.
104 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Can two child restraints be attached using a common lower LATCH anchorage? No Can the rear-facing child restraint touch the back of the front passenger seat? Yes Can the head restraints be removed? Yes; second row outboard positions only, third row all positions. Never “share” a LATCH anchorage with two or more child restraints.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 105 Locating The LATCH Anchorages The lower anchorages are round bars that are found at the rear of the seat cushion where it meets the seatback. They are just visible when you lean into the rear seat to install the child restraint. You will easily feel them if you run your finger along the gap between the seatback and seat cushion.
106 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Each will have a hook or connector to attach to the lower Locating The LATCH Anchorages In addition, there are tether strap anchors lo- anchorage and a way to tighten the connection to the cated behind each rear seatback, near to the floor. anchorage. Forward-facing child restraints and some rear-facing infant restraints will also be equipped with a tether strap.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 107 Center Seat LATCH To Install A LATCH-compatible Child Restraint If a child restraint installed in the center position blocks 1. If the selected seating position has a Switchable Autothe seat belt webbing or buckle for the outboard position, matic Locking Retractor (ALR) seat belt, stow the seat do not use that outboard position. If a child seat in the belt, following the instructions below.
108 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Attach the lower hooks or connectors of the child How To Stow An Unused ALR Seatbelt restraint to the lower anchorages in the selected seat- When using the LATCH attaching system to install a ing position. child restraint, stow all ALR seat belts that are not being 5. If the child restraint has a tether strap, connect it to the used by other occupants or being used to secure child top tether anchorage. See the section “Installing Child restraints.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 109 the seat belt tight around the child restraint so that it is not necessary to use a locking clip. The ALR retractor can Improper installation of a child restraint to the be “switched” into a locked mode by pulling all of the LATCH anchorages can lead to failure of the re- webbing out of the retractor and then letting the webbing straint. The child could be badly injured or killed. retract back into the retractor.
110 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belt Systems for Installing Child Restraints in this Vehicle Second Row Bench Second Row Captains Chair
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 111 Lap/Shoulder Belt Systems What is the weight limit (child’s weight + weight of the child restraint) for using the Tether Anchor with the seat belt to attach a forward facing child restraint? Can the rear-facing child restraint touch the back of the front passenger seat? Weight limit of the Child Restraint Can the head restraints be removed? Yes; second row outboard positions only, third row all positions.
112 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 5. To lock the seat belt, pull down on the shoulder part of the belt until you have pulled all the seat belt webbing out of the retractor. Then, allow the webbing to retract Place the child seat in the center of the seating back into the retractor. As the webbing retracts, you position. For some second row seats, you may need to will hear a clicking sound.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 113 8. If the child restraint has a top tether strap and the Installing A Child Restraint With A Cinching seating position has a top tether anchorage, connect Latch Plate (CINCH) — If Equipped the tether strap to the anchorage and tighten the tether 1. Place the child seat in the center of the seating strap. Refer to “Lower Anchors and Tethers for Chilposition.
114 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Finally, pull up on any excess webbing to tighten the lap portion around the child restraint while you push the child restraint rearward and downward into the vehicle seat. If the buckle or the cinching latch plate is too close to the belt path opening of the child restraint, you may have trouble tightening the seat belt. If this happens, disconnect the latch plate from the buckle and twist the short buckle-end belt up to three full turns to shorten it.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 115 Installing Child Restraints Using The Top Tether Anchorage — Second Row Captains Chairs 3. Attach the tether strap hook of the child restraint to the top tether anchorage as shown in the diagram. 1. Look behind the seating position where you plan to install the child restraint to find the tether anchorage. You may need to move the seat forward to provide better access to the tether anchorage.
116 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchorage position directly behind the child seat to secure a child restraint top tether strap. • If your vehicle is equipped with a split rear seat, make sure the tether strap does not slip into the opening between the seatbacks as you remove slack in the strap. Transporting Pets 4.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 117 COMMERCIAL CARGO VEHICLES (NO FACTORY INSTALLED REAR SEATS) — IF EQUIPPED Commercial cargo vehicles are not designed for use as a family vehicle and are not intended for carrying children in the front passenger seat. However, if you must carry a child in a vehicle without a rear seat, the passenger seat should be moved to the full rearward position and the child must be in a proper restraint system based on its age, size and weight.
118 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Rearward-facing infant restraints must never be secured in the passenger seat of a vehicle with a passenger Air Bag. In a collision, a passenger Air Bag may deploy causing severe injury or death to infants riding in rearward-facing infant restraints.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 119 5. Following the child seat manufacturer’s instructions, tighten the child restraint tether strap. To secure the child restraint upper tether strap to the 6. Inspect the tether anchor strap for nicks, abrasions, vehicle, follow the instructions shown: discoloration, and loose threads. If these, or any other 1. Locate the child restraint tether anchor on the lower condition that might affect the performance of the rear of the front passenger seat.
120 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ENGINE BREAK-IN RECOMMENDATIONS A long break-in period is not required for the engine and drivetrain (transmission and axle) in your vehicle. CAUTION! Never use Non-Detergent Oil or Straight Mineral Oil in the engine or damage may result. Drive moderately during the first 300 miles (500 km). After the initial 60 miles (100 km), speeds up to 50 or NOTE: A new engine may consume some oil during its first few thousand miles (kilometers) of operation.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 121 WARNING! • Do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.
122 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • If it is necessary to sit in a parked vehicle with the engine running, adjust your heating or cooling controls to force outside air into the vehicle. Set the blower at high speed. Open seams or loose connections could permit exhaust fumes to seep into the passenger compartment. In addition, inspect the exhaust system each time the vehicle is raised for lubrication or oil change. Replace as required.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 123 Air Bag Warning Light Floor Mat Safety Information The light should come on and remain on for four to eight seconds as a bulb check when the ignition switch is first turned ON. If the light is not lit during starting, see your authorized dealer. If the light stays on, flickers, or comes on while driving, have the system checked by an authorized dealer. Always use floor mats designed to fit the footwell of your vehicle.
124 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) WARNING! (Continued) • Never place or install floor mats or other floor coverings in the vehicle that cannot be properly secured to prevent them from moving and interfering with the pedals or the ability to control the vehicle. • Never put floor mats or other floor coverings on top of already installed floor mats. Additional floor mats and other coverings will reduce the size of the pedal area and interfere with the pedals.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 125 Periodic Safety Checks You Should Make Outside The Vehicle Door Latches Tires Fluid Leaks Examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread or sidewall. Inspect the tread for cuts and cracks. Inspect sidewalls for cuts, cracks and bulges. Check the wheel nuts for tightness. Check the tires (including spare) for proper cold inflation pressure.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 䡵 MIRRORS . . . . . . . . . . . . . . . . . . . . . . . . . . . .134 ▫ Power Folding Mirrors — If Equipped. . . . . . .139 ▫ Inside Day/Night Mirror — If Equipped . . . .134 ▫ Illuminated Vanity Mirrors — If Equipped . . .139 ▫ Automatic Dimming Mirror — If Equipped . . .135 䡵 BLIND SPOT MONITORING — IF EQUIPPED . . .140 ▫ Outside Mirrors . . . . . . . . . . . . . . . . . . . . . .136 ▫ Rear Cross Path . . . . . . . . . . . . . . . . . . . . . .
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Things You Should Know About Your Uconnect® Phone . . . . . . . . . . . . . . . . . . . . .168 ▫ General Information . . . . . . . . . . . . . . . . . . .180 䡵 VOICE COMMAND — IF EQUIPPED . . . . . . .180 ▫ Voice Command System Operation . . . . . . . . .180 ▫ Commands . . . . . . . . . . . . . . . . . . . . . . . . . .182 ▫ Voice Training . . . . . . . . . . . . . . . . . . . . . . . .186 䡵 SEATS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 䡵 LIGHTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . .223 ▫ Flash-To-Pass . . . . . . . . . . . . . . . . . . . . . . . .229 ▫ Headlight Switch . . . . . . . . . . . . . . . . . . . . . .223 ▫ SmartBeam™ — If Equipped . . . . . . . . . . . . .229 ▫ Automatic Headlights — If Equipped . . . . . . .224 ▫ Battery Protection . . . . . . . . . . . . . . . . . . . . .231 ▫ Headlights On With Wipers — If Equipped . . .
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 䡵 ADJUSTABLE PEDALS — IF EQUIPPED . . . . . .238 ▫ Enabling/Disabling ParkSense® . . . . . . . . . . .248 䡵 ELECTRONIC SPEED CONTROL — IF EQUIPPED . . . . . . . . . . . . . . . . . . . . . . . . .240 ▫ Service The ParkSense® Rear Park Assist System . . . . . . . . . . . . . . . . . . . . . . . . . . . . .249 ▫ To Activate . . . . . . . . . . . . . . . . . . . . . . . . . .241 ▫ Cleaning The ParkSense® System . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 ▫ Sunglass Storage (Non-Sunroof Only) . . . . . . .256 䡵 POWER SUNROOF — IF EQUIPPED . . . . . . . .269 ▫ Rear Courtesy/Reading Lights — If Equipped. . . . . . . . . . . . . . . . . . . . . . . . . .258 ▫ Rear Overhead Consoles — If Equipped . . . . .259 䡵 GARAGE DOOR OPENER — IF EQUIPPED . . .260 ▫ Before You Begin Programming HomeLink® . . .261 ▫ Programming A Rolling Code . . . . . . . . . . . . .262 ▫ Programming A Non-Rolling Code . . . . . . . . .
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 䡵 ELECTRICAL POWER OUTLETS — IF EQUIPPED . . . . . . . . . . . . . . . . . . . . . . . . .272 䡵 POWER INVERTER — IF EQUIPPED. . . . . . . . .277 䡵 CUPHOLDERS . . . . . . . . . . . . . . . . . . . . . . . .278 ▫ Umbrella Holder . . . . . . . . . . . . . . . . . . . . .284 ▫ Second Row Floor Storage Bins . . . . . . . . . . . .284 ▫ Storage Bin Safety Warning. . . . . . . . . . . . . . .285 ▫ Instrument Panel Cupholders . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 䡵 REAR WINDOW FEATURES . . . . . . . . . . . . . .297 䡵 ROOF LUGGAGE RACK — IF EQUIPPED . . . .298 ▫ Rear Window Defroster . . . . . . . . . . . . . . . . .297 ▫ Deploying the Crossbars. . . . . . . . . . . . . . . . .300 䡵 LOAD LEVELING SYSTEM — IF EQUIPPED . . . .298 䡵 SUN SCREENS — IF EQUIPPED . . . . . . . . . . . .
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Day/Night Mirror — If Equipped A two-point pivot system allows for horizontal and vertical adjustment of the mirror. Adjust the mirror to center on the view through the rear window. Headlight glare can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle). The mirror should be adjusted while set in the day position (toward the windshield).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 Automatic Dimming Mirror — If Equipped This mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light to the left of the button will illuminate to indicate when the dimming feature is activated. The sensor to the right of the button does not illuminate. 3 NOTE: This feature is disabled when the vehicle is moving in reverse.
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Outside Mirrors Driver’s Outside Automatic Dimming Mirror — To receive maximum benefit, adjust the outside mirror(s) If Equipped to center on the adjacent lane of traffic with a slight The driver’s outside mirror will automatically adjust for glare from vehicles behind you. This feature is overlap of the view obtained on the inside mirror.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 The power mirror controls consist of mirror select butThe power mirror controls are located on the driver-side tons and a four-way mirror control switch. To adjust a mirror, press either the L (left) or R (right) to select the door trim panel. mirror that you want to adjust. Power Mirrors — If Equipped NOTE: A light in the selected button will illuminate indicating the mirror is activated and can be adjusted.
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Heated Mirrors — If Equipped will move slightly downward from the present position when the vehicle is shifted into REVERSE. The driver’s outside mirror will then return to the original position when the vehicle is shifted out of REVERSE position. Each stored memory setting will have an associated Tilt Mirrors in Reverse position. These mirrors are heated to melt frost or ice.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 Power Folding Mirrors — If Equipped Illuminated Vanity Mirrors — If Equipped The switch for the power folding mirrors is located between the power mirror switches L (left) and R (right). Press the switch once and the mirrors will fold in, pressing the switch a second time will return the mirrors to the normal driving position. An illuminated vanity mirror is located on the sun visor.
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE BLIND SPOT MONITORING — IF EQUIPPED The Blind Spot Monitoring (BSM) system uses two radarbased sensors, located inside the rear bumper fascia, to detect highway licensable vehicles (automobiles, trucks, motorcycles, etc.) that enter the blind spot zones from the rear/front/side of the vehicle. When the vehicle is started, the BSM warning light will momentarily illuminate in both outside rear view mirrors to let the driver know that the system is operational.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 NOTE: • The BSM system does NOT alert the driver about rapidly approaching vehicles that are outside the detection zones. • The BSM system detection zone DOES NOT change if your vehicle is towing a trailer. Therefore, visually verify the adjacent lane is clear for both your vehicle and trailer before making a lane change. If the trailer or other object (i.e.
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Entering From The Side Vehicles that move into your adjacent lanes from either side of the vehicle. BSM Warning Light The BSM system monitors the detection zone from three different entry points (side, rear, front) while driving to see if an alert is necessary. The BSM system will issue an alert during these types of zone entries.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 Entering From The Rear Overtaking Traffic Vehicles that come up from behind your vehicle on either If you pass another vehicle slowly (with a relative speed side and enter the rear detection zone with a relative of less than 10 mph (16 km/h) and the vehicle remains in the blind spot for approximately 1.5 seconds, the speed of less than 30 mph (48 km/h). warning light will be illuminated.
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The BSM system is designed not to issue an alert on stationary objects such as guardrails, posts, walls, foliage, berms, etc. However, occasionally the system may alert on such objects. This is normal operation and your vehicle does not require service.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 The BSM system will not alert you of objects that are traveling in the opposite direction of the vehicle in adjacent lanes. Opposing Traffic WARNING! The Blind Spot Monitoring system is only an aid to help detect objects in the blind spot zones. The BSM system is not designed to detect pedestrians, bicyclists, or animals.
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Cross Path The Rear Cross Path (RCP) feature is intended to aid the driver when backing out of parking spaces where their vision of oncoming vehicles may be blocked. Proceed slowly and cautiously out of the parking space until the rear end of the vehicle is exposed. The RCP system will then have a clear view of the cross traffic and if an oncoming vehicle is detected, alert the driver.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 NOTE: In a parking lot situation, oncoming vehicles can be obscured by vehicles parked on either side. If the sensors are blocked by other structures or vehicles, the system will not be able to alert the driver. Modes Of Operation Three selectable modes of operation are available in the Electronic Vehicle Information Center (EVIC).
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE present. Whenever an audible alert is requested, the radio is also muted. Turn/hazard signal status is ignored; the When operating in Blind Spot Alert Lights/Chime mode, the BSM system will provide a visual alert in the appro- RCP state always requests the chime. priate side view mirror based on a detected object.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 Uconnect® Phone allows you to transfer calls between Uconnect® Phone is a voice-activated, hands-free, in- the system and your mobile phone as you enter or exit vehicle communications system. Uconnect® Phone al- your vehicle and enables you to mute the system’s microphone for private conversation. lows you to dial a phone number with your mobile phone using simple voice commands (e.g.
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Any voice commanded system should be used only in safe driving conditions following all applicable laws, including laws regarding phone use. Your attention should be focused on safely operating the vehicle. Failure to do so may result in a collision causing serious injury or death.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 Operation Voice commands can be used to operate the Uconnect® Phone and to navigate through the Uconnect® Phone menu structure. Voice commands are required after most Uconnect® Phone prompts. You will be prompted for a specific command and then guided through the available options. part of the command when you are asked for it.
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To activate the Uconnect® Phone, simply press the The following are general phone to Uconnect® Phone button and follow the audible prompts for directions. pairing instructions: Uconnect® Phone sessions begin with a press of the button to begin. • Press the button on the radio control head. • After the “Ready” prompt and the following beep, say Cancel Command “Device Pairing”.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 • You will then be asked to give your mobile phone a priority level between one and seven, with one being the highest priority. You can pair up to seven mobile phones to your Uconnect® Phone. However, at any given time, only one mobile phone can be in use, connected to your Uconnect® System. The priority allows the Uconnect® Phone to know which mobile phone to use if multiple mobile phones are in the vehicle at the same time.
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE or downloaded phonebook. To learn how to store a • Automatic download and update, if supported, begins as soon as the Bluetooth® wireless phone connection is name in the phonebook, refer to “Add Names to Your made to the Uconnect® Phone, for example, after you Uconnect® Phonebook”. start the vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 • This downloaded phonebook cannot be edited or • When prompted, enter the number designation (e.g., “Home”, “Work”, “Mobile”, or “Other”). This will deleted on the Uconnect® Phone. These can only be allow you to store multiple numbers for each phoneedited on the mobile phone. The changes are transbook entry, if desired. ferred and updated to Uconnect® Phone on the next phone connection.
156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE After you are finished editing an entry in the phonebook, you will be given the opportunity to edit another entry in NOTE: the phonebook, call the number you just edited, or return • Editing phonebook entries is recommended when the to the main menu. vehicle is not in motion. “Phonebook Edit” can be used to add another phone • Automatic downloaded phonebook entries cannot be number to a name entry that already exists in the phonedeleted or edited. book.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 • After you enter the Phonebook Delete menu, you will then be asked for the name of the entry that you wish to delete. You can either say the name of a phonebook entry that you wish to delete or you can say “List Names” to hear a list of the entries in the phonebook from which you choose. To select one of the entries from the list, button while the Uconnect® Phone is press the playing the desired entry and say “Delete”.
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE List All Names In The Uconnect® Phonebook • Press the Phone Call Features The following features can be accessed through the Uconnect® Phone if the feature(s) are available on your • After the “Ready” prompt and the following beep, say mobile service plan. For example, if your mobile service “Phonebook List Names”. plan provides three-way calling, this feature can be • The Uconnect® Phone will play the names of all the accessed through the Uconnect® Phone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 call. The first call will be on hold while the second call is in progress. To go back to the first call, refer to “Toggling Between Calls” in this section. To combine two calls, refer If a call is currently in progress and you have another to “Conference Call” in this section. incoming call, you will hear the same network tones for call waiting that you normally hear when using your Place/Retrieve A Call From Hold button to place the current mobile phone.
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Conference Call Call Termination When two calls are in progress (one active and one on button until you hear a hold), press and hold the double beep indicating that the two calls have been joined into one conference call. To end a call in progress, momentarily press the button. Only the active call(s) will be terminated and if there is a call on hold, it will become the new active call.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 Call Continuation Uconnect® Phone Features Call continuation is the progression of a phone call on the Language Selection Uconnect® Phone after the vehicle ignition has been To change the language that the Uconnect® Phone is using: switched to OFF. Call continuation functionality avail• Press the button to begin.
162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Emergency Assistance NOTE: If you are in an emergency and the mobile phone is • The emergency number dialed is based on the country reachable: where the vehicle is purchased (911 for the U.S. and Canada and 060 for Mexico). The number dialed may • Pick up the phone and manually dial the emergency not be applicable with the available mobile service and number for your area. area.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 WARNING! To use you Uconnect® Phone System in an emergency, your mobile phone must be: • turned on, • paired to the Uconnect® System, • and have network coverage. Roadside Assistance If you need roadside assistance: • Press the button to begin. • After the “Ready” prompt and the following beep, say “Roadside Assistance”. NOTE: • The roadside assistance number dialed is based on the country where the vehicle is purchased (1-800-528-2069 for the U.S.
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Paging To learn how to page, refer to “Working with Automated Systems”. Paging works properly except for pagers of certain companies, which time out a little too soon to work properly with the Uconnect® Phone. Voice Mail Calling To learn how to access your voice mail, refer to “Working with Automated Systems”.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 The Uconnect® Phone will then send the corresponding Turning Confirmation Prompts ON/OFF phone number associated with the phonebook entry, as Turning confirmation prompts off will stop the system tones over the phone. from confirming your choices (e.g., the Uconnect® Phone NOTE: will not repeat a phone number before you dial it). • You may not hear all of the tones due to mobile phone • Press the button to begin. network configurations. This is normal.
166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Dialing Using The Mobile Phone Keypad Mute/Un-Mute (Mute ON/OFF) You can dial a phone number with your mobile phone keypad and still use the Uconnect® Phone (while dialing via the mobile phone keypad, the user must exercise caution and take precautionary safety measures). By dialing a number with your paired Bluetooth® mobile phone, the audio will be played through your vehicle’s audio system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 If you would like to connect or disconnect the Bluetooth® connection between your mobile phone and the Uconnect® Transfer Call To And From Mobile Phone Phone System, follow the instructions described in your The Uconnect® Phone allows ongoing calls to be trans- mobile phone User’s Manual. ferred from your mobile phone to the Uconnect® Phone List Paired Mobile Phone Names without terminating the call.
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Select Another Mobile Phone Delete Uconnect® Phone Paired Mobile Phones This feature allows you to select and start using another • Press the button to begin. phone paired with the Uconnect® Phone. • After the “Ready” prompt and the following beep, say button to begin. • Press the “Setup Phone Pairing”. • After the “Ready” prompt and the following beep, say • At the next prompt, say “Delete” and follow the prompts. “Setup Select Phone” and follow the prompts.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 Voice Training For users experiencing difficulty with the system recognizing their voice commands or numbers, the Uconnect® Phone Voice Training feature may be used. To enter this training mode, follow one of the two following procedures: Voice Training session should be completed when the vehicle is parked with the engine running, all windows closed, and the blower fan switched off. This procedure may be repeated with a new user.
170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Command • fully closed windows, • dry weather condition. • For best performance, adjust the rearview mirror to provide at least ½ in (1 cm) gap between the overhead • Even though the system is designed for users speaking console (if equipped) and the mirror. in North American English, French, and Spanish ac• Always wait for the beep before speaking. cents, the system may not always work for some.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 • Numbers must be spoken in single digits. “800” must be spoken “eight-zero-zero” not “eight hundred”. • You can say “O” (letter “O”) for “0” (zero). • fully closed windows, • dry weather conditions, and • operation from the driver’s seat.
172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Text Reply Send Messages: Uconnect® Phone can read or send new messages on You can send messages using Uconnect® Phone. To send your phone. a new message: Read Messages: • Press the button. If you receive a new text message while your phone is • After the “Ready” prompt and the following beep, say connected to Uconnect® Phone, an announcement will “SMS Send” or “Send Message.” be made to notify you that you have a new text message.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173 List of Preset Messages: 10. Thanks 1. Yes 11. See You in 15 minutes 2. No 12. I am on my way 3. Where are you? 13. I’ll be late 4. I need more direction. 14. Are you there yet? 5. L O L 15. Where are we meeting? 6. Why 16. Can this wait? 7. I love you 17. Bye for now 8. Call me 18. When can we meet? 9. Call me later 19. Send number to call 20.
174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Turn SMS Incoming Announcement ON/OFF Bluetooth® Communication Link Turning the SMS Incoming Announcement OFF will stop Mobile phones have been found to lose connection to the the system from announcing the new incoming messages. Uconnect® Phone. When this happens, the connection can generally be reestablished by switching the phone • Press the button. off/on.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175 3
176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177 3
178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Commands Primary Alternate (s) zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location Voice Commands Primary Alternate (s) all call cancel confirmation prompts continue delete dial download edit emergency English erase all Espanol Francais
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179 Voice Commands Primary Alternate (s) help home language list names list phones mobile mute mute off new entry no other pair a phone phone pairing pairing phonebook phone book Voice Commands Primary Alternate (s) previous record again redial return to main menu return or main menu select phone select send set up phone settings or phone set up towing assistance transfer call Uconnect® Tutorial voice training work yes 3
180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE General Information VOICE COMMAND — IF EQUIPPED This device complies with Part 15 of the FCC rules and Voice Command System Operation RSS 210 of Industry Canada.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181 WARNING! Any voice commanded system should be used only in safe driving conditions following all applicable laws. Your attention should be focused on safely operating the vehicle. Failure to do so may result in a collision causing serious injury or death. Pressing the Voice Command button while the system is speaking is known as “barging in.” The system will be interrupted, and after the beep, you can add or change commands.
182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE At any point, if the system does not recognize one of your Main Menu commands, you will be prompted to repeat it. Start a dialogue by pressing the Voice Command To hear the first available Menu, press the Voice Combutton. You may say “Main Menu” to switch to the button and say “Help” or “Main Menu”. mand main menu.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 183 Radio AM • “Menu Radio” (to switch to the radio menu) To switch to the AM band, say “AM” or “Radio AM”. In • “Main Menu” (to switch to the main menu) this mode, you may say the following commands: Satellite Radio • “Frequency #” (to change the frequency) To switch to satellite radio mode, say “Sat” or “Satellite Radio”.
184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Disc Mode Bluetooth® Streaming (BT) Mode To switch to the disc mode, say “Disc”. In this mode, you To switch to Bluetooth® Streaming (BT) mode, say may say the following commands: “Bluetooth Streaming”.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 185 – “Delete” (to delete the recording) • “Main menu setup” or • “Play Memos” (to play previously recorded memos) — During the playback you may press the Voice Combutton to stop playing memos.
186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Training SEATS For users experiencing difficulty with the system recog- Seats are a part of the Occupant Restraint System of the nizing their voice commands or numbers the Uconnect® vehicle. Voice “Voice Training” feature may be used. button, say “System 1. Press the Voice Command Setup” and once you are in that menu then say “Voice Training.” This will train your own voice to the system and will improve recognition. 2.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 187 Power Seats — If Equipped Some models may be equipped with eight-way power seats for the driver and front passenger. The power seat switches are located on the outboard side of the seat. The switches control the movement of the seat cushion and the seatback.
188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! CAUTION! • Adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • Seats should be adjusted before fastening the seat belts and while the vehicle is parked. Serious injury or death could result from a poorly adjusted seat belt. • Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 189 Tilting The Seat Up Or Down The angle of the seat cushion can be adjusted in four directions. Pull upward or push downward on the front or rear of the seat switch, the front or rear of the seat cushion will move in the direction of the switch. Release the switch when the desired position has been reached. Reclining The Seatback The angle of the seatback can be adjusted forward or rearward.
190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Do not place any article under a power seat or impede its ability to move as it may cause damage to the seat controls. Seat travel may become limited if movement is stopped by an obstruction in the seat’s path. Power Lumbar — If Equipped Vehicles equipped with power driver or passenger seats may be also be equipped with power lumbar. The power lumbar switch is located on the outboard side of the power seat.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 191 Heated Seats — If Equipped Vehicles Equipped With Remote Start On some models, the front and rear seats may be On models that are equipped with remote start, the equipped with heaters located in the seat cushions. driver’s heated seat can be programmed to come on during a remote start.
192 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Press the switch once to select HIGH-level heating. Press the switch a second time to select LOW-level heating. Press the switch a third time to shut the heating elements OFF. Rear Heated Seats On some models, the second row seats are equipped with heaters. There are two heated seat switches that allow the second row passengers to operate the seats indepenNOTE: Once a heat setting is selected, heat will be felt dently.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 193 You can choose from HIGH, LOW or OFF heat settings. Manual Front/Second Row Seat Adjuster Amber indicator lights in each switch indicate the level of Both front seats are adjustable forward or rearward. The heat in use. Two indicator lights will illuminate for manual seat adjustment handle is located under the seat HIGH, one for LOW and none for OFF. cushion at the front edge of each seat. Press the switch once to select HIGH-level heating.
194 UNDERSTANDING THE FEATURES OF YOUR VEHICLE While sitting in the seat, pull up on the handle and slide Manual Reclining Seats — If Equipped the seat forward or rearward. Release the bar once you For models equipped with manual reclining seats, the have reached the desired position. Then, using body recline lever is located on the outboard side of the seat. pressure, move forward and rearward on the seat to be sure that the seat adjusters have latched.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 195 To recline, lean forward slightly, lift the lever, then push back to the desired position and release the lever. Lean forward and lift the lever to return the seatback to its normal position. Using body pressure, lean forward and rearward on the seat to be sure the seatback has latched. Head Restraints Head restraints are designed to reduce the risk of injury by restricting head movement in the event of a rear impact.
196 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To raise the head restraint, pull upward on the head Active Head Restraints are passive, deployable compo- restraint. To lower the head restraint, press the push nents, and vehicles with this equipment cannot be readily button, located at the base of the head restraint, and push identified by any markings, only through visual inspec- downward on the head restraint. tion of the head restraint.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 197 For comfort the Active Head Restraints can be tilted forward and rearward. To tilt the head restraint closer to the back of your head, pull forward on the bottom of the head restraint. Push rearward on the bottom of the head restraint to move the head restraint away from your head.
198 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: • The head restraints should only be removed by qualified technicians, for service purposes only. If either of the head restraints require removal, see your authorized dealer. • In the event of deployment of an Active Head Restraint, refer to “Occupant Restraints/Resetting Active Head Restraints (AHR)” in “Things To Know Before Starting Your Vehicle” for further information.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 199 Head Restraints — Second Row Quad Seats Head Restraints — Second Row Bench To raise the head restraint, pull upward on the head restraint. To lower the head restraint, press the push button, located at the base of the head restraint, and push downward on the head restraint. To raise the head restraint, pull upward on the head restraint.
200 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Slide the storage bin locking mechanism to the “LOCK” position and then pull up on the storage bin On vehicles equipped with Stow ’n Go® seating, the latch to open the cover. second and third row seats can be folded into the floor for convenient storage. Stow ’n Go® Seating — If Equipped Second Row Stow ’n Go® On vehicles equipped with Stow ’n Go® seats, the seats will fold and tumble in one motion. 1. Move the front seat fully forward. 2.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 201 5. Pull upward on the seatback recliner lever located on The non-adjustable head restraint and seatback will fold the outboard side of the seat. automatically during the seat tumble. No additional actuation is necessary.
202 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Folding Seatback Tumbled Second Row Seat The seat will automatically tumble into position for easy 6. Push the seat into the storage bin. storage.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 203 CAUTION! The storage bin cover must be locked and flat to avoid damage from contact with the front seat tracks, which have minimal clearance to the cover. 3 WARNING! Seat In Storage Bin 7. Close the storage bin cover. In a collision, serious injury could result if the seat storage bin covers are not properly latched. • Do not drive the vehicle with the storage bin covers open. • Keep the storage bin covers closed and latched while the vehicle is in motion.
204 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Unstow Second Row Seats 1. Return the seatback to the upright position. 1. Pull up on the storage bin latch to open the cover. 2. Pull up on the strap to lift the seat out of the storage bin and push the seat rearward to latch the seat anchors. 3. Lift the seatback to the full upright position. 4. Return the head restraint to its upright position, close the storage bin cover and slide the storage bin locking mechanism to the “Unlocked” position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 205 2. Return the head restraint to the upright position. Easy Entry Second Row The second row Stow ’n Go® seats allow easy entry to the third row seat or rear cargo area. Pull up on the seatback recliner lever on the outboard side of the seat. Raising The Head Restraint 3. Pull up on the seatback recliner lever on the outboard side of the seat to fold head rest and seatback and tumble seat forward.
206 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The seat will automatically fold into position for easy entry into the third row. WARNING! In the event of a collision you could be injured if the seat is not fully latched. Quad Seats — If Equipped Both Quad seats are adjustable forward or rearward. The manual seat adjustment handle is located under the seat cushion at the front edge of each seat. Manual Seat Adjuster While sitting in the seat, pull up on the handle and slide the seat forward or rearward.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 207 WARNING! • Adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • Seats should be adjusted before fastening the seat belts and while the vehicle is parked. Serious injury or death could result from a poorly adjusted seat belt.
208 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Fold-Flat Easy Entry To fold the seat, lift the recliner lever to the full upward The Quad seats can be tilted forward for easy entry into position and push the seatback forward until it rests on the third row. With the Quad seat in the fold-flat position, the seat cushion. lift up on the easy entry lever located near the bottom of the seat and lift the seat forward.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 209 For passengers seated in the third row, there is a pull strap located on the outboard side of the seat near the bottom of the seat back. Third row passengers can pull on the strap and push the Quad seat forward for folding the seatback and accessing the easy entry lever. Pull Strap for Third Row Passengers Removal The Quad seats can be removed if additional storage is needed.
210 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Release levers are located on the rear leg assemblies, near While the bench seat does not stow in the floor, it is the floor. To remove the seat, squeeze each release handle and rotate downwards to deploy the wheels. A lock removable for added cargo space. indicator button pops up when the seat is unlocked. The seat assembly can now be removed from the vehicle and moved on its Easy Out® Rollers.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 211 To reinstall the seat, align the seat into the detent positions on the floor. Squeeze the release handle and rotate upward until the lock indicator button returns into the handle. Third Row Power Recline — If Equipped The power recline feature, located on the side of the seat cushion, adjusts the seatback angle forward/rearward for occupant comfort. WARNING! 3 If not properly latched, the bench seats could become loose. Personal injuries could result.
212 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The switch is only functional when the liftgate is open Third Row Power Folding Seat — If Equipped A one-touch power folding seat switch is located in the and the vehicle is in PARK. left rear trim panel as part of a switch bank. NOTE: Lower the head restraint by pulling on the release strap marked “1” located on the outboard side of the head restraint.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 213 Left and right third row seats can be folded individually NOTE: or together. The third row power folding seat adjusts to • Disconnect the center shoulder belt from the small the following positions using the switch bank located on buckle and lower the head restraints before attempting the left rear trim panel: to fold/stow the power third row seats.
214 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Pull release strap marked “2” located on the rear of the Manually Folding Third Row Seats — If Equipped seat to lower the seatback. 1. Lower the center head restraint down to the seatback by pushing the button on the guide and pushing the head restraint down. 2. Lower the outboard head restraints by pulling on the release strap marked “1” located on the outboard side of the head restraint.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 215 4. Pull release strap marked “3” to release the anchors. 5. Pull release strap marked “4” and tumble the seat rearward into the storage bin.
216 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Pull release strap marked “2” to unlock the recliner. 3. Pulling strap “4” releases the seatback to return to its full upright position. 4. Raise the head restraint to its upright position. WARNING! In a collision, you or others in your vehicle could be injured if seats are not properly latched to their floor attachments. Always be sure the seats are fully latched. Stowed Third Row Seat Tailgate Mode 1.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 217 WARNING! To avoid serious injury or death, never operate the vehicle with occupants in the third row seat while in the tailgate mode. Plastic Grocery Bag Retainer Hooks Retainer hooks which will hold plastic grocery bag handles are built into the seatbacks of all rear seats and some front seats. The floor supports the partial weight of the bagged goods.
218 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Setting Memory Positions And Linking RKE Transmitter To Memory 4. Adjust the brake and accelerator pedals to the desired positions. NOTE: Each time the SET (S) button and a numbered 5. Turn on the radio and set the radio station presets button (1 or 2) is pressed, you erase the memory settings (up to 10 AM and 10 FM stations can be set). for that button and store a new one. 6. Turn the ignition switch to the OFF position and 1.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 219 9. Select “Remote Linked to Memory” in the Electronic Vehicle Information Center (EVIC) and enter “Yes”. Refer to “Electronic Vehicle Information Center (EVIC)/ Customer-Programmable Features” in “Understanding Your Instrument Panel” for further information. Memory Position Recall NOTE: The vehicle must be in PARK to recall memory positions. If a recall is attempted when the vehicle is not in PARK, a message will be displayed in the EVIC.
220 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To disable another RKE transmitter linked to either Memory Position, repeat Steps 1 to 5 for each RKE Turn the ignition switch to the OFF position and transmitter. remove the key. NOTE: Once programmed, all RKE transmitters linked Press and release MEMORY button 1. The system will to memory can be easily enabled or disabled at one time. recall any memory settings stored in position 1.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 221 The distance the driver seat moves depends on where • The Easy Entry/Easy Exit feature is disabled when you have the driver seat positioned when you remove the the driver seat position is less than 0.9 in (22.7 mm) forward of the rear stop. At this position, there is no key from the ignition switch. benefit to the driver by moving the seat for Easy Exit • When you remove the key from the ignition switch, or Easy Entry. the driver seat will move about 2.
222 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Move to the front of the vehicle and look inside the center of the hood opening. Locate, then push the To open the hood, two latches must be released. safety catch lever downward while raising the hood 1. Pull the hood release lever located on the instrument at the same time. panel, below the steering column.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 223 Use the hood prop rod to secure the hood in the open position. CAUTION! To prevent possible damage, do not slam the hood to close it. Lower the hood until it is open approximately 12 in (30 cm) and then drop it. This should secure both latches. Never drive your vehicle unless the hood is fully closed, with both latches engaged. LIGHTS Headlight Switch The headlight switch is located on the left side of the instrument panel.
224 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rotate the headlight switch clockwise to the first detent for parking light and instrument panel light operation. Rotate the headlight switch to the second detent for headlight, parking light and instrument panel operation. Headlights On With Wipers — If Equipped When your headlights are in the AUTO mode and the engine is running, the headlights will automatically turn on when the wiper system is also turned on.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 225 When exiting the vehicle the driver can choose to have the headlights remain on for 30, 60 or 90 seconds or not remain on. To change the timer setting, see your authorized dealer. The headlight delay time is programmable on vehicles equipped with an EVIC. Refer to “Electronic Vehicle Information Center (EVIC)/Customer-Programmable Features” in “Understanding Your Instrument Panel” for further information.
226 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Interior Lighting On Dimmer Controls The dimmer switch is located next to the headlight switch. Rotate the left dimmer control completely upward to the second detent (extreme top position) to turn on the interior lights. The interior lights will remain on when the dimmer control is in this position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 227 NOTE: The key must be out of the ignition switch or the The Halo control switch is located to the right of the ignition switch must be in the OFF position for this dimmer switch. feature to operate. Interior Lighting Off Rotate the left dimmer control to the off position (extreme bottom). The interior lights will remain off when the doors or liftgate are open. 3 Parade Mode (Daytime Brightness Feature) Rotate the left dimmer control to the first detent.
228 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Multifunction Lever The multifunction lever controls the: The multifunction lever is located on the left side of the • Turn Signals steering column. • Headlight Beams Low/High • Flash-To-Pass (Optical Horn) • Front and Rear Wipers — Washer Functions Turn Signals Move the multifunction lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 229 Turn Signal Warning Flash-To-Pass If the vehicle electronics sense that the vehicle has traveled at over 18 mph (29 km/h) for about 1 mile (1.6 km) with the turn signals on, a chime will sound to alert the driver. You can signal another vehicle with your headlights by lightly pulling the multifunction lever toward you. This will cause the headlights to turn on at high beam and remain on until the lever is released.
230 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Activate To Deactivate 1. Select “Automatic High Beams — ON” through the Perform either of the following steps to deactivate the EVIC. Refer to “Electronic Vehicle Information Center SmartBeam™ system. (EVIC)/Customer-Programmable Features” in “Under1. Select “Automatic High Beams — OFF” through the standing Your Instrument Panel” for further informaEVIC. Refer to “Electronic Vehicle Information Center tion.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 231 Battery Protection WINDSHIELD WIPER AND WASHERS This feature provides battery protection to avoid wearing The wipers and washers are operated by a switch within down the battery if the headlights, parking lights, or the multifunction lever. Rotate the end of the multifuncfront fog lights are left on for extended periods of time tion lever to select the desired wiper speed. when the ignition switch is in the LOCK position.
232 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Always remove any buildup of snow that prevents the windshield wiper blades from returning to the off position. If the windshield wiper switch is turned off and the blades cannot return to the off position, damage to the wiper motor may occur. WARNING! Sudden loss of visibility through the windshield could lead to a collision. You might not see other vehicles or other obstacles.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 233 Windshield Washers Rear Wiper And Washer To use the Washer, push on the end of the lever to the second detent and hold while spray is desired. If the lever is pushed while on the intermittent setting, the wipers will turn on and operate for several wipe cycles after the lever is released, and then resume the intermittent interval previously selected.
234 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The sensitivity of the system is adjustable from the multifunction lever. Wiper sensitivity position 3 has been calibrated for best overall wiping sensitivity. If the operator desires more wiping sensitivity, they may select sensitivity positions 4 or 5. If the operator desires less wiping sensitivity, they may select sensitivity positions 2 or 1. Place the multifunction lever in the OFF position when not using the system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 235 • Neutral Wipe Inhibit — The Rain Sensing feature will not operate when the ignition is ON, and the transmission shift lever is in the NEUTRAL position, and the vehicle speed is less than 5 mph (8 km/h), unless the wiper control on the multifunction lever is moved or the shift lever is moved out of the NEUTRAL position. TILT/TELESCOPING STEERING COLUMN This feature allows you to tilt the steering column upward or downward.
236 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To unlock the steering column, push the lever downward (toward the floor). To tilt the steering column, move the steering wheel upward or downward as desired. To lengthen or shorten the steering column, pull the steering wheel outward or push it inward as desired. To lock the steering column in position, push the lever upward until fully engaged. WARNING! Do not adjust the steering column while driving.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 237 Press the switch to turn on the heated steering wheel. The light on the switch will illuminate to indicate the steering wheel heater is on. Pressing the switch a second time will turn off the heated steering wheel and light indicator. NOTE: The engine must be running for the heated steering wheel to operate.
238 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ADJUSTABLE PEDALS — IF EQUIPPED The adjustable pedals system is designed to allow a greater range of driver comfort for steering wheel tilt and seat position. This feature allows the brake, accelerator, and clutch pedals (if equipped) to move toward or away from the driver to provide improved position with the steering wheel. The switch is located on the left side of the steering column.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 239 • The pedals can be adjusted with the ignition OFF. • The pedals cannot be adjusted when the vehicle is in REVERSE or when the Electronic Speed Control System is on. The following messages will be displayed on vehicles equipped with the Electronic Vehicle Information System (EVIC) if the pedals are attempted to be adjusted when the system is locked out (“Adjustable Pedal Disabled — Cruise Control Engaged” or “Adjustable Pedal Disabled — Vehicle In Reverse”.
240 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ELECTRONIC SPEED CONTROL — IF EQUIPPED When engaged, the Electronic Speed Control takes over accelerator operations at speeds greater than 25 mph (40 km/h). The Electronic Speed Control buttons are located on the right side of the steering wheel.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 241 NOTE: In order to ensure proper operation, the Electronic Speed Control System has been designed to shut down if multiple Speed Control functions are operated at the same time. If this occurs, the Electronic Speed Control System can be reactivated by pushing the Electronic Speed Control ON/OFF button and resetting the desired vehicle set speed. WARNING! Leaving the Electronic Speed Control system on when not in use is dangerous.
242 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Deactivate A soft tap on the brake pedal, pushing the CANCEL button, or normal brake pressure while slowing the vehicle will deactivate Electronic Speed Control without erasing the set speed memory. Pressing the ON/OFF button or turning the ignition switch OFF erases the set speed memory. increase until the button is released, then the new set speed will be established. Pressing the RES (+) button once will result in a 1 mph (1.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 243 To Accelerate For Passing Press the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. Using Electronic Speed Control On Hills The transmission may downshift on hills to maintain the vehicle set speed. WARNING! Electronic Speed Control can be dangerous where the system cannot maintain a constant speed. Your vehicle could go too fast for the conditions, and you could lose control and have an accident.
244 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ParkSense® will retain the last system state (enabled or ParkSense® Sensors disabled) from the last ignition cycle when the ignition is The four ParkSense® sensors, located in the rear fascia/ changed to the ON/RUN position. bumper, monitor the area behind the vehicle that is ParkSense® can be active only when the shift lever is in within the sensors’ field of view. The sensors can detect REVERSE.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 245 The ParkSense® Warning Display is located in the Instru- ParkSense® Display ment cluster’s EVIC display. It provides both visual and When the vehicle is in REVERSE, the warning display audible warnings to indicate the distance between the will turn ON indicating the system status. rear fascia/bumper and the detected obstacle.
246 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The system will indicate a detected obstacle by showing three solid arcs and will produce a one-half second tone. As the vehicle moves closer to the object the EVIC display will show fewer arcs and the sound tone will change from slow, to fast, to continuous.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 247 3 Fast Tone Continuous Tone
248 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The vehicle is close to the obstacle when the EVIC display shows one flashing arc and sounds a continuous tone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 249 When ParkSense® is disabled, the instrument cluster will display the “PARK ASSIST SYSTEM OFF” message for approximately five seconds. Refer to “Electronic Vehicle Information Center (EVIC)” in “Understanding Your Instrument Panel” for further information. When the shift lever is moved to REVERSE and the system is disabled, the EVIC will display the “PARK ASSIST SYSTEM OFF” message for as long as the vehicle is in REVERSE. information.
250 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • When you move the shift lever to the REVERSE position and ParkSense® is turned OFF, the EVIC will Clean the ParkSense® sensors with water, car wash soap display “PARK ASSIST SYSTEM OFF” message for as and a soft cloth. Do not use rough or hard cloths. Do not long as the vehicle is in REVERSE. scratch or poke the sensors. Otherwise, you could damage the sensors. • ParkSense®, when on, will MUTE the radio when it is sounding a tone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 251 rear fascia/bumper. Failure to do so can result in the system misinterpreting a close object as a sensor problem, causing the “SERVICE PARK ASSIST SYSTEM” message to be displayed in the EVIC . • On vehicles equipped with a tailgate, ParkSense® should be disabled when the tailgate is in the lowered or open position and the vehicle is in REVERSE. A lowered tailgate could provide a false indication that an obstacle is behind the vehicle.
252 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! (Continued) • Before using ParkSense®, it is strongly recommended that the ball mount and hitch ball assembly is disconnected from the vehicle when the vehicle is not used for towing. Failure to do so can result in injury or damage to vehicles or obstacles because the hitch ball will be much closer to the obstacle than the rear fascia when the loudspeaker sounds the continuous tone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 253 When displayed, static grid lines will illustrate the width zones that will help indicate the distance to the rear of of the vehicle while a dashed center-line will indicate the vehicle. The following table shows the approximate the center of the vehicle to assist with aligning to a distances for each zone: hitch/receiver.
254 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! • To avoid vehicle damage, ParkView® should only be used as a parking aid. The ParkView® camera is unable to view every obstacle or object in your drive path. • To avoid vehicle damage, the vehicle must be driven slowly when using ParkView® to be able to stop in time when an obstacle is seen. It is recommended that the driver look frequently over his/her shoulder when using ParkView®. Turning ParkView® On Or Off — With Navigation/Multimedia Radio 1.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 255 OVERHEAD CONSOLES Front Overhead Console Two versions of the overhead console are available. The base front overhead console model featured fixed incandescent courtesy/reading lights, flip-down sunglass storage and conversation mirror.
256 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Courtesy/Interior Lighting Sunglass Storage (Non-Sunroof Only) At the forward end of the console are two courtesy lights (standard dome light has two buttons). The lights turn on when a front door, a sliding door or the liftgate is opened. If your vehicle is equipped with Remote Keyless Entry (RKE) the lights will also turn on when the UNLOCK button on the RKE transmitter is pressed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 257 The door will slowly rotate to the full open position. 3 Conversation Mirror Position NOTE: From the “conversation mirror” position, the From this position, the door can be fully closed or, by door can only be closed. rotating upward about 3/4 of the way and releasing, To return to the full open position, the door must first be positioned for conversation mirror use. closed and then opened by pressing the latch again to Full Open Position release.
258 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Courtesy/Reading Lights — If Equipped The overhead console has two sets of courtesy lights. The lights turn on when a front door, a sliding door or the liftgate is opened. If your vehicle is equipped with Remote Keyless Entry (RKE) the lights will also turn on when the UNLOCK button on the RKE transmitter is pressed. The courtesy lights also function as reading lights. Press in on each lens to turn these lights on while inside the vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 259 Rear Overhead Consoles — If Equipped The rear overhead storage system is available in two versions: with or without sunroof. An additional LED at the front of the rear console shines down on the front foot-well area while in courtesy mode, for added convenience. 3 Overhead Compartment Features 1 — DVD* 2 — Rear HVAC 3 — Interior Lights 4 — Storage * If equipped, otherwise storage.
260 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The HomeLink® buttons, located on either the overhead console, headliner or sunvisor, designate the three differThe rear overhead console has recessed halo lighting ent HomeLink® channels. The HomeLink® indicator is around the perimeter of the console base. This feature located above the center button. provides additional lighting options while traveling and is controlled by the headlight switch.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 261 Before You Begin Programming HomeLink® Be sure that your vehicle is parked outside of the garage before you begin programming. For more efficient programming and accurate transmission of the radio-frequency signal it is recommended that a new battery be placed in the hand-held transmitter of the device that is being programmed to the HomeLink® system. Erase all channels before you begin programming.
262 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: • Erasing all channels should only be performed when programming HomeLink® for the first time. Do not erase channels when programming additional buttons. • If you have any problems, or require assistance, please call toll-free 1–800–355–3515 or, on the Internet at www.HomeLink.com for information or assistance. Programming A Rolling Code For programming garage door openers that were manufactured after 1995.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 263 1. Cycle the ignition to the ON/RUN position. 2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) away from the HomeLink® button you wish to program while keeping the HomeLink® indicator light in view. Firmly press and release the “LEARN” or “TRAINING” button. On some garage door openers/devices there may be a light that blinks when the garage door opener/device is in the LEARN/TRAIN mode. NOTE: You have 30 seconds in which to initiate the next 3.
264 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Reprogramming A Single HomeLink® Button 3. Simultaneously press and hold both the Homelink® button you want to program and the hand-held transTo reprogram a channel that has been previously trained, mitter button. follow these steps: 4. Continue to hold both buttons and observe the indicator light. The Homelink® indicator will flash slowly 2.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 265 which may not be long enough for HomeLink® to pick up the signal during programming. Similar to this Canadian To reprogram a channel that has been previously trained, law, some U.S. gate operators are designed to time-out in follow these steps: the same manner. 1. Turn the ignition switch to the ON/RUN position. It may be helpful to unplug the device during the cycling 2.
266 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Watch for the HomeLink® indicator to change flash Reprogramming A Single HomeLink® Button rates. When it changes, it is programmed. It may take To reprogram a channel that has been previously trained, up to 30 seconds or longer in rare cases. The garage follow these steps: door may open and close while you are programming. 1. Cycle the ignition to the ON/RUN position. 5. Press and hold the programmed HomeLink® button 2.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 267 system, entry door lock, home/office lighting, etc.,). The Troubleshooting Tips hand-held transmitter of the device may also be used at If you are having trouble programming HomeLink®, any time. here are some of the most common solutions: Security • Replace the battery in the original hand-held transmitter. It is advised to erase all channels before you sell or turn in your vehicle.
268 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Your motorized door or gate will open and close while you are programming the universal transceiver. Do not program the transceiver if people, pets or other objects are in the path of the door or gate. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by Federal safety standards. This includes most garage door opener models manufactured after 1982.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 269 POWER SUNROOF — IF EQUIPPED The power sunroof switch is located between the sun visors on the overhead console. Power Sunroof Switch WARNING! • Never leave children unattended in a vehicle, and do not leave the key in the ignition switch (or leave the ignition of a vehicle equipped with Keyless Enter-N-Go™ in the ACC or ON/Run position).
270 UNDERSTANDING THE FEATURES OF YOUR VEHICLE position. The sunroof will close fully and stop automatically. This is called “Express Close”. During Express Press the switch rearward and release it within one-half Close operation, any movement of the switch will stop second. The sunroof and sunshade will open automatithe sunroof. cally from any position. The sunroof and sunshade will open fully and stop automatically. This is called “Express Closing Sunroof — Manual Mode Open”.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 271 NOTE: If three consecutive sunroof close attempts result Wind Buffeting in Pinch Protect reversals, the fourth close attempt will be Wind buffeting can be described as the perception of a Manual Close movement with Pinch Protect disabled. pressure on the ears or a helicopter-type sound in the ears.
272 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Ignition Off Operation Sunroof Fully Closed For Vehicles Not Equipped With The Electronic Vehicle Press the switch forward and release to ensure that the Information Center (EVIC) sunroof is fully closed. The power sunroof switch will remain active for 45 seconds ELECTRICAL POWER OUTLETS — IF EQUIPPED after the ignition switch is turned to the LOCK position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 273 CAUTION! Instrument Panel Outlets NOTE: To ensure proper operation a MOPAR® cigar knob and element must be used. • Do not exceed the maximum power of 160 Watts (13 Amps) at 12 Volts. If the 160 Watt (13 Amp) power rating is exceeded the fuse protecting the system will need to be replaced. • Power outlets are designed for accessory plugs only. Do not insert any other object in the power outlets as this will damage the outlet and blow the fuse.
274 UNDERSTANDING THE FEATURES OF YOUR VEHICLE One outlet in the removable floor console (if equipped) shares a fuse with the lower outlet in the instrument panel and is also connected to the battery. Do not exceed a maximum power of 160 Watts (13 Amps) shared between the lower panel outlet and the removable floor console outlet. On vehicles equipped with the Super Console the power outlets are located under the retractable cover.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 275 The outlet in the rear quarter panel near the liftgate and the upper outlet in the instrument panel are both controlled by the ignition switch. Each of these outlets can support 160 Watts (13 Amps). Do not exceed 160 Watts (13 Amps) for each of these outlets. 3 The power outlets include tethered caps, labeled with a key or battery symbol indicating the power source.
276 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! CAUTION! (Continued) To avoid serious injury or death: • Only devices designed for use in this type of outlet should be inserted into any 12 Volt outlet. • Do not touch with wet hands. • Close the lid when not in use and while driving the vehicle. • If this outlet is mishandled, it may cause an electric shock and failure. • Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.), will degrade the battery even more quickly.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 277 The power inverter switch is located on the instrument A 110 Volt, 150 Watt inverter outlet (if equipped) converts panel below the climate controls. DC current to AC current, and is located on the left To turn on the power outlet, press the switch once. Press rear trim panel immediately behind the second row left the switch a second time to turn the power outlet off. passenger seat.
278 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CUPHOLDERS There are cupholders located throughout the interior. All liners are removable for cleaning. Pull the flexible liner from the cupholder drawer or tray starting at one edge for easy removal. Refer to “Cleaning The Instrument Panel Cupholders” in “Maintaining Your Vehicle” for further information. Instrument Panel Cupholders The instrument panel cupholders are located in a pull-out drawer just above the lower storage bin.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 279 For rear passengers two cupholders are located in the On models equipped with the Super Console, there are pull-out drawer, located in the back of the Super Console. Pull the drawer out to the first position to use the two cupholders located in the center of the console. cupholders.
280 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Premium Console Cupholders — If Equipped Interior Bottle Holders On models equipped with premium center consoles, there There are four bottle holders located in the interior. One are four cupholders located on the top of the console. bottle holder is molded into each front interior door trim panels, and one bottle holder is molded into each side sliding interior door trim panel. Each holder accommodates up to a 20 oz (.6 L) plastic bottle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 281 Smoker’s Package Kit — If Equipped With the optional authorized dealer-installed Smoker’s Package Kit, a removable ash receiver is inserted into one of the two cupholders in the center front instrument panel. To install the ash receiver, align the receiver so the thumb grip on the lid is facing rearward. Press the ash receiver into either of the cup wells to secure. Pull upward on the ash receiver to remove for cleaning and/or storage.
282 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Upper Glove Compartment Lower Glove Compartment To open the upper compartment, press in on the button, To open the lower compartment pull out on the release located on the left side of the upper door. The door will handle. automatically open. Lower Compartment Upper Compartment To close the compartment door, push downward on the door’s surface to latch the door closed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 283 Door Trim Panel Storage Driver Seatback Storage — If Equipped Front Door Storage The driver’s seatback has a primary storage pocket on all models and an optional secondary mesh pocket. Both interior front door panels have multiple pockets for storage. 3 WARNING! If containers of hot liquid are placed in the bottle holder, they can spill when the door is closed, burning the occupants. Be careful when closing the doors to avoid injury.
284 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Umbrella Holder Second Row Floor Storage Bins An umbrella holder has been conveniently molded into The area below the floor covers, located in front of the the left front door entry scuff molding. second row seats, is available for storage.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 285 Pull up on the storage bin latch to open the cover. Slide the storage bin locking mechanism to the ⬙unlocked⬙ position to allow greater access to the storage bin. CAUTION! The storage bin cover must lay flat and be locked to avoid damage from contact with the front seat tracks, which have minimal clearance to the cover. WARNING! (Continued) • Do not operate the storage bin covers while the vehicle is in motion. • Do not use a storage bin latch as a tie down.
286 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! (Continued) • In a collision, serious injury could result if the seat storage bin covers are not properly latched. • Do not drive the vehicle with the storage bin covers open. Keep the storage bin covers closed and latched while the vehicle is in motion. • Do not operate the storage bin covers while the vehicle is in motion. • Do not use a storage bin latch as a tie down.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 287 NOTE: In the event of an individual being locked inside the storage bin, the storage bin cover can be opened from inside of the bin by pushing on the glow-in-the-dark lever attached to the storage bin cover latching mechanism. 3 Center And Rear Overhead Console Storage — If Equipped The overhead storage system comes in several options. Overhead Console Features 1 — DVD* 2 — Rear HVAC 3 — Courtesy Lights 4 — Storage * If equipped, otherwise storage.
288 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Coat Hooks Coat hooks are located along the headliner for the second and third row seating positions. The coat hook load limit is 10 lbs (4.5 kg). Exceeding the recommended load limit can cause the coat hooks to break or disengage from the vehicle. Cargo Area Storage The liftgate sill plate has a raised line with the statement “Load To This Line”. This line indicates how far rearward cargo can be placed without interfering with liftgate closing.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 289 CONSOLE FEATURES Basic Console There are three consoles available: Basic, Premium and Basic Console features consist of the following: Super. • The basic console profile allows vehicle occupants to easily pass through the first row to the second. WARNING! Do not operate this vehicle with a console compartment lid in the open position. Cellular phones, music players, and other handheld electronic devices should be stowed while driving.
290 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Remove The Basic Floor Console 1. Remove the front anchor cup plug and clip. 2. Slide the console base forward while lifting slightly to clear the rear load floor hook. 3. Remove the console. To Reinstall The Basic Floor Console 5. Pull up on the console to be sure it is firmly latched. WARNING! In an accident, serious injury could result if the removable floor console is not properly installed. Always be sure the removable floor console is fully latched.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 291 • Upper storage bin can hold nine regular or 18 thin CDs Position 1 shows the console closed with four cupholders or other items and a convenient storage tray. • Large console center storage will store headphones for the available rear DVD entertainment system or other items 3 • 12 Volt DC power outlet provides continuous power inside the console for cell phones or other electronics.
292 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Position 2 shows the raised storage tray revealing a large Dual Storage Bins storage area below. Position 3 shows the top portion of the console in a rearward position. This is accomplished by lifting the upper most latch at the front of the console. This provides easy access to the storage area below and provides two of the four cupholders for the second row passengers.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 293 Position 4 shows the complete console in its rearmost To Remove The Premium Floor Console position. Again, lifting second latch handle at the front of 1. Pull up on the bottom release handle in the front of the the console, allows complete access to a lower storage bin console. and provides additional cupholders for rear passengers. 2. Lift the rear of the console up several inches/centimeters. 3. Pull rearward to disengage from floor and remove console.
294 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Push down on the rear of the console until it is seated in the rear floor bracket. 5. Pull up on the console to be sure it is firmly latched. WARNING! In an accident, serious injury could result if the removable floor console is not properly installed. Always be sure the removable floor console is fully latched.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 295 NOTE: The front cupholder light ring and pass through lighting is controlled by a dimming switch located on the instrument panel, refer to “Lights” in “Understanding The Features Of Your Vehicle” for further information. Located in the back of the super console is a storage drawer and cupholders for the rear passengers.
296 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CARGO AREA FEATURES Press in on the flashlight to release it. Rechargeable Flashlight The rechargeable flashlight is mounted on the right side of the cargo area. The flashlight snaps out of the bezel when needed. The flashlight features two bright LED light bulbs and is powered by a lithium battery that recharges when snapped back into place and the vehicle is either running or the key is in the accessory position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 297 To operate the flashlight, press the switch once for high, REAR WINDOW FEATURES twice for low, and a third time to return to off. Rear Window Defroster The rear window defroster button is located on the climate control (Mode) knob. Press this button to turn on the rear window defroster and the heated outside mirrors (if equipped). An indicator in the button will illuminate when the rear window defroster is on.
298 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Failure to follow these cautions can cause damage to the heating elements: • Use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements. Labels can be peeled off after soaking with warm water.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 299 crossbars, to maximum of 150 lbs (68 kg). The roof rack does not increase the total load carrying capacity of the vehicle. Be sure the total load of cargo inside the vehicle plus that on the external rack does not exceed the maximum vehicle load capacity. The crossbars and side rails are designed to carry weight on vehicles equipped with a luggage rack.
300 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Deploying the Crossbars CAUTION! To deploy the crossbars, completely loosen the thumb Use care when removing and handling the crossbars screws at both ends of the crossbar and lift the crossbar to prevent damage to the vehicle. from its stowed position in the side rail. Repeat with crossbar on the opposite side. Bend the crossbar supports at each end, taking care to keep hand clear of pivoting joint. Slide the thumb screw down.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 301 Then, position the crossbars across the roof. NOTE: The crossbars are identical and can be placed in any two of the three deploy positions.
302 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Make sure the directional arrows on the crossbars align Once the crossbars are set into position, tighten the thumb with the directional arrows on the side rails. Set the screws completely. crossbars into the deployed positions.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 303 Stowing the Crossbars Reverse the procedure to stow the crossbars, again, taking care to keep hand clear of pivoting joint. Crossbars are identical and can be stowed in either rail nest. Once the crossbars are stowed, tighten the thumb screws completely. 3 NOTE: Load should always be secured to crossbars first, with rail tie down loops used as additional securing points if needed. Tie loops are intended as supplementary tie down points only.
304 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! CAUTION! (Continued) • Check deployed crossbars frequently and retighten thumb screws as necessary. • To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity of 150 lb (68 kg). Always distribute heavy loads as evenly as possible and secure the load appropriately. • To prevent damage to the roof of your vehicle, DO NOT carry any loads on the roof rack without the crossbars deployed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 305 WARNING! Cargo must be securely tied before driving your vehicle. Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage. Follow the roof rack cautions when carrying cargo on your roof rack. SUN SCREENS — IF EQUIPPED Sun screens are available for second and third row seating windows.
306 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Gently pull up on the tab to raise the sun screen. Continue pulling the sun screen until the tab is near the top of the window. Once the screen is completely to the top of the window, extend the top bar of the sun screen over the two hooks attached to the top of the window. Sun Screen Extended To lower the sun screen, gently lift the tab upward to disengage the hooks, and feed the screen back into the base sill.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 INSTRUMENT PANEL FEATURES . . . . . . . . . .312 ▫ Oil Change Required . . . . . . . . . . . . . . . . . . .339 䡵 INSTRUMENT CLUSTER — BASE . . . . . . . . . .313 ▫ Fuel Economy . . . . . . . . . . . . . . . . . . . . . . . .340 䡵 INSTRUMENT CLUSTER — PREMIUM . . . . . . .314 ▫ Vehicle Speed . . . . . . . . . . . . . . . . . . . . . . . .341 䡵 INSTRUMENT CLUSTER DESCRIPTIONS . . . . .315 ▫ Trip Info . . . . . . . . . . . . . . . . . . . . . . . . . . .
308 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Vehicle Info (Customer Information Features) . . .343 䡵 Uconnect® 130 . . . . . . . . . . . . . . . . . . . . . . . .355 ▫ Messages # . . . . . . . . . . . . . . . . . . . . . . . . . .344 ▫ Operating Instructions — Radio Mode. . . . . . .355 ▫ Keyless Enter-N-Go™ Display — If Equipped. . . . . . . . . . . . . . . . . . . . . . . . . .344 ▫ Operation Instructions — CD MODE For CD And MP3 Audio Play. . . . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 309 ▫ Uconnect® (Satellite Radio) — If Equipped . . .376 䡵 UCONNECT® MULTIMEDIA — VIDEO ENTERTAINMENT SYSTEM (VES™) — ▫ Operating Instructions (Uconnect® Phone) — If Equipped . . . . . . . . . . . . . . . . . . . . . If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . .380 ▫ Getting Started . . . . . . . . . . . . . . . . . 䡵 SETTING THE ANALOG CLOCK . . . . . . . . . . .381 ▫ Blu-ray Player . . . . . . . . . . . . . . . . . .
310 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Listen To An Audio Source While A Video Is Playing . . . . . . . . . . . . . . . . . . . . . . . . . . .403 ▫ Unwired® Stereo Headphone Lifetime Limited Warranty . . . . . . . . . . . . . . . . . . . . .416 ▫ Important Notes For Dual Video Screen System . . . . . . . . . . . . . . . . . . . . . . . . . . . . .405 ▫ System Information . . . . . . . . . . . . . . . . . . . .417 ▫ VES™ Remote Control – If Equipped . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 311 䡵 STEERING WHEEL AUDIO CONTROLS — IF EQUIPPED . . . . . . . . . . . . . . . . . . . . . . . . .434 ▫ Automatic Temperature Control (ATC) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . .446 ▫ Radio Operation . . . . . . . . . . . . . . . . . . . . . .435 ▫ Summer Operation . . . . . . . . . . . . . . . . . . . .458 ▫ CD Player . . . . . . . . . . . . . . . . . . . . . . . . . . .435 ▫ Winter Operation. . . . . . . . . . . . . . . . . . . . . .
312 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT PANEL FEATURES 1 2 3 4 — Air Vents — Instrument Cluster — Shift Lever — Radio 5 6 7 8 — Analog Clock — Upper Glove Compartment — Lower Glove Compartment — Climate Controls 9 — DVD – If Equipped 10 — Storage Bin 11 — Cup Holders 12 — Switch Bank 13 14 15 16 — — — — Ignition Switch Hood Release Dimmer Switch Headlight Switch
UNDERSTANDING YOUR INSTRUMENT PANEL 313 INSTRUMENT CLUSTER — BASE 4
314 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER — PREMIUM
UNDERSTANDING YOUR INSTRUMENT PANEL 315 If the vehicle is driven more than 1 mile (1.6 km) with either turn signal on, a continuous chime will sound to 1. Tachometer alert you to turn the signal off. If either indicator flashes This gauge measures engine revolutions per minute at a rapid rate, check for a defective outside light bulb. (RPM x 1000). Before the pointer reaches the red area, 5. High Beam Indicator ease up on the accelerator to prevent engine damage.
316 UNDERSTANDING YOUR INSTRUMENT PANEL odometer needs to be repaired or serviced, the repair technician should leave the odometer reading the same as it was before the repair or service. If s/he cannot do so, then the odometer must be set at zero, and a sticker must be placed in the door jamb stating what the mileage was before the repair or service.
UNDERSTANDING YOUR INSTRUMENT PANEL 317 Refer to ”Electronic Vehicle Information Center (EVIC) noFUSE Display — If Equipped” for further information. If the vehicle diagnostic system determines that the Ignition Off Draw (IOD) fuse is improperly installed, or LoW tirE When the appropriate condition exists, the odometer dis- damaged, a “noFUSE” message will display in the odometer display area. For further information on fuses and fuse play will toggle between LoW and tirE for three cycles.
318 UNDERSTANDING YOUR INSTRUMENT PANEL Unless reset, this message will continue to display each time you turn the ignition switch to the ON/RUN position. To turn off the message temporarily, press and release the STEP button on the steering wheel. To reset the oil change indicator system (after performing the scheduled maintenance), perform the following steps.
UNDERSTANDING YOUR INSTRUMENT PANEL 319 If the ABS light is on, the brake system should be serviced as soon as possible to restore the benefits of Anti-Lock brakes. If the ABS light does not turn on when the ignition switch is turned to the ON/RUN position, have the light inspected by an authorized dealer. 8.
320 UNDERSTANDING YOUR INSTRUMENT PANEL Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is combined with the low tire pressure telltale. When the system detects a malfunction, the telltale will flash for approximately one minute and then remain continuously illuminated. This sequence will continue upon subsequent vehicle start-ups as long as the malfunction exists.
UNDERSTANDING YOUR INSTRUMENT PANEL 321 9. Malfunction Indicator Light (MIL) The Malfunction Indicator Light (MIL) is part of an onboard diagnostic system, called OBD, that monitors engine and automatic transmission control systems. The light will illuminate when the key is in the ON/RUN position, before engine start. If the bulb does not come on when turning the key from OFF to ON/RUN, have the condition checked promptly. Certain conditions, such as a loose or missing gas cap, poor fuel quality, etc.
322 UNDERSTANDING YOUR INSTRUMENT PANEL 10. Electronic Stability Control (ESC) Activation/ Malfunction Indicator Light — If Equipped Each time the ignition is turned to ON/RUN, the ESC system will be ON, even if it was turned off previously. The “ESC Activation/Malfunction Indicator Light” in the instrument cluster will come on when the ignition switch is turned to the ON/RUN position. It should go out with the engine running.
UNDERSTANDING YOUR INSTRUMENT PANEL 323 13. Fuel Door Reminder 16. Shift Lever Indicator The arrow in this symbol is a reminder that the The Shift Lever Indicator is self-contained within the Fuel Filler Door is located on the left side of the instrument cluster. It displays the gear position of the automatic transmission. vehicle. NOTE: 14. Fuel Gauge You must apply the brakes before shifting from PARK.
324 UNDERSTANDING YOUR INSTRUMENT PANEL 18. Brake Warning Light This light monitors various brake functions, including brake fluid level and parking brake application. If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the anti-lock brake system reservoir.
UNDERSTANDING YOUR INSTRUMENT PANEL 325 Vehicles equipped with the Anti-Lock Brake System 19. Seat Belt Reminder Light (ABS), are also equipped with Electronic Brake Force When the ignition switch is first turned to ON/ Distribution (EBD). In the event of an EBD failure, the RUN, this light will turn on for four to eight secBrake Warning Light will turn on along with the ABS onds as a bulb check. During the bulb check, if the Light. Immediate repair to the ABS system is required.
326 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! WARNING! (Continued) Driving with a hot engine cooling system could damage your vehicle. If the temperature gauge reads “H” pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the “H” and you hear continuous chimes, turn the engine off immediately and call an authorized dealer for service.
UNDERSTANDING YOUR INSTRUMENT PANEL 327 If the charging system light remains on, it means that the 24. Engine Temperature Warning Light vehicle is experiencing a problem with the charging This light warns of an overheated engine condisystem. Obtain SERVICE IMMEDIATELY. See an authotion. As engine coolant temperatures rise and the rized dealer.
328 UNDERSTANDING YOUR INSTRUMENT PANEL 25. Electronic Throttle Control (ETC) Light 26. Transmission Temperature Warning Light During sustained high speed driving or trailer This light informs you of a problem with the towing up long grades on hot days, the autoElectronic Throttle Control (ETC) system. The matic transmission oil may become too hot. light will come on when the ignition is first When the transmission overheat warning light turned to ON/RUN and remain on briefly as a bulb check.
UNDERSTANDING YOUR INSTRUMENT PANEL 329 CAUTION! Continuous driving with the Transmission Temperature Warning Light illuminated will eventually cause severe transmission damage or transmission failure. ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) — IF EQUIPPED The Electronic Vehicle Information Center (EVIC) features a driver-interactive display that is located in the instrument cluster.
330 UNDERSTANDING YOUR INSTRUMENT PANEL This system conveniently allows the driver to select a The system allows the driver to select information by variety of useful information by pressing the switches pressing the following buttons mounted on the steering mounted on the steering wheel.
UNDERSTANDING YOUR INSTRUMENT PANEL 331 UP Button Press and release the UP button to scroll upward through the main menus (Fuel Economy, Vehicle Info, Tire PSI, Cruise, Messages, Units, System Setup) and sub-menus. DOWN Button BACK Button Press the BACK button to scroll back to a previous menu or sub-menu. Electronic Vehicle Information Center (EVIC) Displays Press and release the DOWN button to scroll The EVIC display consists of three sections: downward through the main menus and 1.
332 UNDERSTANDING YOUR INSTRUMENT PANEL The main display area will normally display the main menu or the screens of a selected feature of the main menu. The main display area also displays ⬙pop up⬙ messages that consist of approximately 60 possible warning or information messages.
UNDERSTANDING YOUR INSTRUMENT PANEL 333 The Reconfigurable Telltales section is divided into the • Wrong Key white telltales area on the right, amber telltales in the • Damaged Key middle, and red telltales on the left.
334 UNDERSTANDING YOUR INSTRUMENT PANEL • RKE Battery Low • Service Keyless System • LOW WASHER FLUID • Oil Change Required • Check Gascap • Left Front Turn Signal Light Out • Left Rear Turn Signal Light Out • Right Front Turn Signal Light Out • Right Rear Turn Signal Light Out • Blind Spot System Off — This message is displayed when the ignition is turned to ON to indicate the Blind Spot System has been turned off.
UNDERSTANDING YOUR INSTRUMENT PANEL 335 EVIC White Telltale Lights This area will show reconfigurable white caution telltales. These telltales include: • Electronic Range Select (ERS) Status The shift lever status “5,4,3,2,1” are displayed indicating the shift lever position. Telltales “5,4,3,2,1” indicate the Electronic Range Select (ERS) feature has been engaged and the gear selected is displayed.
336 UNDERSTANDING YOUR INSTRUMENT PANEL will display in the telltale display area. Tighten the fuel • Oil Pressure Warning Light filler cap properly and press the SELECT button to turn This light indicates low engine oil pressure. The off the message. If the problem continues, the message light should turn on momentarily when the engine is will appear the next time the vehicle is started. started.
UNDERSTANDING YOUR INSTRUMENT PANEL 337 If the light remains lit with the engine running, your vehicle will usually be drivable. However, see an authorized dealer for service as soon as possible. If the light is flashing when the engine is running, immediate service is required. You may experience reduced performance, an If jump starting is required, refer to “Jump Starting elevated/rough idle or engine stall and your vehicle may Procedures” in “What To Do In Emergencies”. require towing.
338 UNDERSTANDING YOUR INSTRUMENT PANEL If the light turns on while driving, safely pull over and stop the vehicle. If the A/C system is on, turn it off. Also, shift the transmission into NEUTRAL and idle the vehicle. If the temperature reading does not return to normal, turn the engine off immediately and call for service. Refer to “If Your Engine Overheats” in “What To Do In Emergencies” for more information.
UNDERSTANDING YOUR INSTRUMENT PANEL 339 Oil Change Required Vehicles Equipped With Keyless Enter-N-Go™ Your vehicle is equipped with an engine oil change 1. Without pressing the brake pedal, push the ENGINE START/STOP button and cycle the ignition to the indicator system. The Oil Change Required message will ON/ RUN position (Do not start the engine.) flash in the EVIC display for approximately 10 seconds, after a single chime has sounded, to indicate the next 2.
340 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: If the indicator message illuminates when you fuel economy is reset, the display will read “zero” for start the engine, the oil change indicator system did not two seconds. Then, the history information will be erased, and the averaging will continue from the last fuel reset. If necessary, repeat these steps. average reading before the reset.
UNDERSTANDING YOUR INSTRUMENT PANEL 341 Distance To Empty (DTE) Miles Per Gallon (MPG) Shows the estimated distance that can be traveled with the fuel remaining in the tank. This estimated distance is determined by a weighted average of the instantaneous and average fuel economy, according to the current fuel tank level. DTE cannot be reset through the SELECT button. This display shows the instantaneous MPG in bar graph form while driving.
342 UNDERSTANDING YOUR INSTRUMENT PANEL Trip Info Elapsed Time Press and release the UP or DOWN button until “Trip Info” is highlighted in the EVIC and press the SELECT button. Press and release the UP/DOWN buttons to highlight one of the following functions if you want to reset it: Shows the total elapsed time of travel since the last reset when the ignition switch is in the ACC position. Elapsed time will increment when the ignition switch is in the ON or START position.
UNDERSTANDING YOUR INSTRUMENT PANEL 343 Units • Coolant Temp Press and release the UP or DOWN button until “Units” displays highlighted in the EVIC and press the SELECT button. The EVIC, odometer, and navigation system (if equipped) can be changed between English and Metric units of measure.
344 UNDERSTANDING YOUR INSTRUMENT PANEL Messages # Compass / Temperature Display Select from Main Menu using the UP or DOWN buttons. This feature shows the number of stored warning messages (in the # place holder). Pressing the SELECT button will allow you to see what the stored messages are. Press and release the UP and DOWN buttons if there is more than one message to step through the remaining stored messages. Pressing the BACK button takes you back to the Main Menu.
UNDERSTANDING YOUR INSTRUMENT PANEL 345 also calibrate the compass by completing one or more 3. Press the DOWN button until “Calibrate Compass” is displayed in the EVIC then press and release the 360–degree turns (in an area free from large metal or SELECT button. metallic objects) until the CAL indicator displayed in the EVIC turns off. The compass will now function normally. 4. Press and release the SELECT button to start the calibration.
346 UNDERSTANDING YOUR INSTRUMENT PANEL Compass Variance Compass Variance is the difference between Magnetic North and Geographic North. To compensate for the differences the variance should be set for the zone where the vehicle is driven, per the zone map. Once properly set, the compass will automatically compensate for the differences, and provide the most accurate compass heading. For the most accurate compass performance, the compass must be set using the following steps.
UNDERSTANDING YOUR INSTRUMENT PANEL 347 Press and release the UP or DOWN button until ⬙System Setup⬙ is highlighted in the main menu of the EVIC. Then press the SELECT button to enter the System Setup sub-menu. Press and release the UP or DOWN button to 4. Press and release the SELECT button until the proper select a feature form the following choices: variance zone is selected, according to the map. Language 3.
348 UNDERSTANDING YOUR INSTRUMENT PANEL is removed showing the system has been deactivated. Refer to “Rear Park Assist System” in “Understanding When this feature is selected the navigation system The Features Of Your Vehicle” for system function and utilizes voice commands, guiding you through the drive operating information. route mile by mile, turn-by-turn until the final destination is reached.
UNDERSTANDING YOUR INSTRUMENT PANEL 349 Door 1st Press is selected, you must press the RKE transmitter UNLOCK button twice, to unlock the passenger’s doors. When All Doors 1st Press is selected, all of the doors will unlock on the first press of the RKE transmitter UNLOCK button. To make your selection, press and release the SELECT button until a check-mark appears next to the feature showing the system has been activated or the check-mark is removed showing the system has been deactivated.
350 UNDERSTANDING YOUR INSTRUMENT PANEL press and release the SELECT button until a check-mark a check-mark appears next to the feature showing the appears next to the feature showing the system has been system has been activated or the check-mark is removed activated or the check-mark is removed showing the showing the system has been deactivated. system has been deactivated.
UNDERSTANDING YOUR INSTRUMENT PANEL 351 then press and release the SELECT button until a check- Intermittent Wiper Options — If Equipped mark appears next to the setting, showing that the setting When ON is selected, the system will automatically has been selected. activate the windshield wipers if it senses moisture on the windshield.
352 UNDERSTANDING YOUR INSTRUMENT PANEL highlighted, then press and release the SELECT button Flashers with Sliding Door until a check-mark appears next to the setting, showing When this feature is selected the signal lamps activate that the setting has been selected. when power or manual sliding doors are in operation, signaling other drivers that someone may be exiting or Illuminated Approach entering the vehicle.
UNDERSTANDING YOUR INSTRUMENT PANEL 353 To make your selection, press and release the SELECT button until a check-mark appears next to the feature This feature provides automatic driver seat positioning to showing the system has been activated or the check-mark enhance driver mobility when entering and exiting the is removed showing the system has been deactivated. vehicle.
354 UNDERSTANDING YOUR INSTRUMENT PANEL To make your selection, press and release the SELECT button until a check-mark appears next to the feature showing the system has been activated or the check-mark is removed showing the system has been deactivated. NOTE: If your vehicle has experienced any damage in the area where the sensor is located, even if the fascia is not damaged, the sensor may have become misaligned. Take your vehicle to an authorized dealer to verify sensor alignment.
UNDERSTANDING YOUR INSTRUMENT PANEL 355 Uconnect® 130 Operating Instructions — Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Control (Rotary) Push the ON/VOLUME control knob to turn on the radio. Push the ON/VOLUME control knob a second time to turn off the radio. Electronic Volume Control Uconnect® 130 The electronic volume control turns continuously (360 degrees) in either direction, without stopping.
356 UNDERSTANDING YOUR INSTRUMENT PANEL 3. After adjusting the hours, press the right side TUNE/ SCROLL control knob to set the minutes. The minutes Press and release the SEEK buttons to search for the next will begin to blink. listenable station in AM/FM mode. Press the right switch to seek up and the left switch to seek down. The radio 4. Adjust the minutes using the right side TUNE/ will remain tuned to the new station until you make SCROLL control knob. Press the TUNE/SCROLL conanother selection.
UNDERSTANDING YOUR INSTRUMENT PANEL 357 Push the rotary TUNE/SCROLL control knob a fifth time and FADE will display. Turn the TUNE/SCROLL control Push the rotary TUNE/SCROLL control knob and BASS knob to the left or right to adjust the sound level between will display. Turn the TUNE/SCROLL control knob to the front and rear speakers. the right or left to increase or decrease the bass tones.
358 UNDERSTANDING YOUR INSTRUMENT PANEL You may add a second station to each pushbutton by repeating the above procedure with this exception: Press the SET/RND button twice and SET 2 will show in the display window. Each button can be set for SET 1 and SET 2 in both AM and FM. This allows a total of 12 AM and 12 FM stations to be stored into pushbutton memory. The stations stored in SET 2 memory can be selected by pressing the pushbutton twice.
UNDERSTANDING YOUR INSTRUMENT PANEL 359 If you insert a disc with the ignition ON and the radio ON, the unit will switch from radio to CD mode and begin to play when you insert the disc. The display will show the track number, and index time in minutes and seconds. Play will begin at the start of track 1. CAUTION! (Continued) • Dual-media disc types (one side is a DVD, the other side is a CD) should not be used, and they can cause damage to the player.
360 UNDERSTANDING YOUR INSTRUMENT PANEL SEEK Button AM/FM Button Press the right SEEK button for the next selection on the CD. Press the left SEEK button to return to the beginning of the current selection, or return to the beginning of the previous selection if the CD is within the first second of the current selection. Pressing and holding the SEEK button will allow faster scrolling through the tracks in CD and MP3 modes. Press the button to select either AM or FM mode.
UNDERSTANDING YOUR INSTRUMENT PANEL 361 Notes on Playing MP3 Files The radio uses the following limits for file systems: The radio can play MP3 files; however, acceptable MP3 file • Maximum number of folder levels: 8 recording media and formats are limited. When writing • Maximum number of files: 255 MP3 files, pay attention to the following restrictions. • Maximum number of folders. (The radio display of file Supported Media (Disc Types) names and folder names is limited.
362 UNDERSTANDING YOUR INSTRUMENT PANEL Multisession disc formats are supported by the radio. Multisession discs may contain combinations of normal CD audio tracks and computer files (including MP3 files). Discs created with an option such as ⬙keep disc open after writing⬙ are most likely multisession discs. The use of multisession for CD audio or MP3 playback may result in longer disc loading times. MPEG Specification MPEG-1 Audio Layer 3 Sampling Frequency (kHz) 48, 44.
UNDERSTANDING YOUR INSTRUMENT PANEL 363 Playback of MP3 Files Operation Instructions - Auxiliary Mode When a medium containing MP3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3 files.
364 UNDERSTANDING YOUR INSTRUMENT PANEL Uconnect® 130 WITH SATELLITE RADIO Operating Instructions — Radio Mode NOTE: The ignition switch must be in the ON/RUN or ACC position to operate the radio. Power Switch/Volume Control (Rotary) Push the ON/VOLUME control knob to turn on the radio. Push the ON/VOLUME control knob a second time to turn off the radio. Electronic Volume Control Uconnect® 130 The electronic volume control turns continuously (360 degrees) in either direction, without stopping.
UNDERSTANDING YOUR INSTRUMENT PANEL 365 If your vehicle is not equipped with or this feature is not Press and release the SEEK buttons to search for the next available on your vehicle, a “Not Equipped With Uconnect listenable station in AM/FM mode. Press the right switch Phone” message will display on the radio screen. to seek up and the left switch to seek down.
366 UNDERSTANDING YOUR INSTRUMENT PANEL starting at Step 2. For vehicles not equipped with satellite radio, press the SETUP button and then follow the above 1. Press and hold the TIME button until the hours blink. procedure, starting at Step 2. 2. Adjust the hours by turning the right side TUNE/ INFO Button SCROLL control knob. Press the INFO button for an RDS station (one with call 3. After adjusting the hours, press the right side TUNE/ letters displayed).
UNDERSTANDING YOUR INSTRUMENT PANEL 367 Push the rotary TUNE/SCROLL control knob a fifth time and FADE will display. Turn the TUNE/SCROLL control Push the rotary TUNE/SCROLL control knob and BASS knob to the left or right to adjust the sound level between will display. Turn the TUNE/SCROLL control knob to the front and rear speakers. the right or left to increase or decrease the bass tones.
368 UNDERSTANDING YOUR INSTRUMENT PANEL Toggle the MUSIC TYPE button to select the following format types: Program Type No program type or undefined Adult Hits Classical Classic Rock College Country Foreign Language Information Jazz News Nostalgia 16-Digit Character Display None Adlt Hit Classicl Cls Rock College Country Language Inform Jazz News Nostalga Program Type Oldies Personality Public Rhythm and Blues Religious Music Religious Talk Rock Soft Soft Rock Soft Rhythm and Blues Sports Talk Top 40 Wea
UNDERSTANDING YOUR INSTRUMENT PANEL 369 By pressing the SEEK button when the Music Type icon is AM/FM Button displayed, the radio will be tuned to the next frequency Press the button to select either AM or FM mode. station with the same selected Music Type name. The Music Type function only operates when in the FM mode.
370 UNDERSTANDING YOUR INSTRUMENT PANEL SET 2 in both AM and FM. This allows a total of 12 AM Operation Instructions — CD MODE for CD and and 12 FM stations to be stored into pushbutton memory. MP3 Audio Play The stations stored in SET 2 memory can be selected by NOTE: pressing the pushbutton twice. • The ignition switch must be in the ON/RUN or ACC Every time a preset button is used, a corresponding position to operate the radio. button number will display.
UNDERSTANDING YOUR INSTRUMENT PANEL 371 If you insert a disc with the ignition ON/RUN and the radio ON, the unit will switch from radio to CD mode and begin to play when you insert the disc. The display will show the track number, and index time in minutes and seconds. Play will begin at the start of track 1. CAUTION! (Continued) • Dual-media disc types (one side is a DVD, the other side is a CD) should not be used, and they can cause damage to the player.
372 UNDERSTANDING YOUR INSTRUMENT PANEL SEEK Button AM/FM Button Press the right SEEK button for the next selection on the CD. Press the left SEEK button to return to the beginning of the current selection, or return to the beginning of the previous selection if the CD is within the first second of the current selection. Pressing and holding the SEEK button will allow faster scrolling through the tracks in CD and MP3 modes. Press the button to select either AM or FM mode.
UNDERSTANDING YOUR INSTRUMENT PANEL 373 Notes On Playing MP3 Files The radio uses the following limits for file systems: The radio can play MP3 files; however, acceptable MP3 file • Maximum number of folder levels: 8 recording media and formats are limited. When writing • Maximum number of files: 255 MP3 files, pay attention to the following restrictions. • Maximum number of folders. (The radio display of file Supported Media (Disc Types) names and folder names is limited.
374 UNDERSTANDING YOUR INSTRUMENT PANEL Multisession disc formats are supported by the radio. Multisession discs may contain combinations of normal CD audio tracks and computer files (including MP3 files). Discs created with an option such as ⬙keep disc open after writing⬙ are most likely multisession discs. The use of multisession for CD audio or MP3 playback may result in longer disc loading times. MPEG Specification MPEG-1 Audio Layer 3 Sampling Frequency (kHz) 48, 44.
UNDERSTANDING YOUR INSTRUMENT PANEL 375 Playback of MP3 Files When a medium containing MP3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3 files. LIST Button (CD Mode for MP3 Play) Pressing the LIST button will bring up a list of all folders on the disc. Scrolling up or down the list is done by turning the TUNE/SCROLL control knob.
376 UNDERSTANDING YOUR INSTRUMENT PANEL Press and hold the INFO button again for three seconds to return to ⬙elapsed time⬙ display. Operation Instructions - Auxiliary Mode The auxiliary (AUX) jack is an audio input jack which allows the user to plug in a portable device such as an MP3 player or iPod® and utilize the vehicle’s audio system to amplify the source and play through the vehicle speakers.
UNDERSTANDING YOUR INSTRUMENT PANEL 377 Electronic Serial Number/Sirius Identification Number (ESN/SID) Selecting Uconnect® (Satellite) Mode Press the SAT button until ⬙SAT⬙ appears in the display. Please have the following information available when A CD may remain in the radio while in the Satellite radio calling: mode. 1. The Electronic Serial Number/Sirius Identification Satellite Antenna Number (ESN/SID). To ensure optimum reception, do not place items on the 2. Your Vehicle Identification Number.
378 UNDERSTANDING YOUR INSTRUMENT PANEL Reception Quality SEEK Buttons Satellite reception may be interrupted due to one of the Press and release the SEEK buttons to search for the next following reasons: channel in Satellite mode. Press the right switch to seek • The vehicle is parked in an underground parking up and the left switch to seek down. The radio will remain tuned to the new channel until you make another structure or under a physical obstacle. selection.
UNDERSTANDING YOUR INSTRUMENT PANEL 379 additional three seconds will make the radio display the Toggle the MUSIC TYPE button again to select the music Song Title all of the time (press and hold again to return type. to normal display). By pressing the SEEK button when the Music Type function is active, the radio will be tuned to the next RW/FF channel with the same selected Music Type name.
380 UNDERSTANDING YOUR INSTRUMENT PANEL This allows a total of 12 Satellite channels to be stored into pushbutton memory. The channels stored in SET 2 When you are receiving a channel that you wish to commit to pushbutton memory, press the SET button. memory can be selected by pressing the pushbutton twice. The symbol SET 1 will now show in the display window. Select the button (1-6) you wish to lock onto this channel Every time a preset button is used, a corresponding and press and release that button.
UNDERSTANDING YOUR INSTRUMENT PANEL 381 SETTING THE ANALOG CLOCK iPod®/USB/MP3 CONTROL — IF EQUIPPED To set the analog clock at the top center of the instrument NOTE: This section is for sales code RES and REQ/ panel, press and hold the button until the setting is REL/RET radios only with Uconnect®. For sales code correct. RBZ/RHB, RHR, RHP, RHW or RB2 touch-screen radio iPod®/USB/MP3 control feature, refer to the separate RBZ/RHB, RHR, RHP, RHW or RB2 User’s Manual.
382 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: • If the radio has a USB port, refer to the appropriate Uconnect® Multimedia radio User’s Manual for iPod® or external USB device support capability. • Connecting an iPod® or consumer electronic audio device to the AUX port located in the radio faceplate, plays media, but does not use the iPod® /MP3 control feature to control the connected device.
UNDERSTANDING YOUR INSTRUMENT PANEL 383 not available in the glove compartment, route the cable Using This Feature away from the lid latch and in a place that will allow the By using an iPod® cable, or an external USB device to lid to close without damaging the cable.
384 UNDERSTANDING YOUR INSTRUMENT PANEL Controlling The iPod® Or External USB Device Using Radio Buttons • Turning it clockwise (forward) by one click, while playing a track, skips to the next track or press the VR button and say ⬙Next Track⬙.
UNDERSTANDING YOUR INSTRUMENT PANEL 385 • Use the << SEEK and SEEK>> buttons to jump to the • Press the SCAN button to use iPod®/USB/MP3 deprevious or next track. Pressing the SEEK>> button vice scan mode, which will play the first 10 seconds of each track in the current list and then forward to the during play mode will jump to the next track in the next song.
386 UNDERSTANDING YOUR INSTRUMENT PANEL List Or Browse Mode During Play mode, pressing any of the buttons described below, will bring up List mode. List mode enables scrolling through the list of menus and tracks on the audio device. • TUNE control knob: The TUNE control knob functions in a similar manner as the scroll wheel on the audio device or external USB device.
UNDERSTANDING YOUR INSTRUMENT PANEL 387 • To exit List mode without selecting a track, press the same PRESET button again to go back to Play mode. • LIST button: The LIST button will display the top level menu of the iPod® or external USB device. Turn the TUNE control knob to list the top-menu item to be selected and press the TUNE control knob. This will display the next sub-menu list item on the audio device, then follow the same steps to go to the desired track in that list.
388 UNDERSTANDING YOUR INSTRUMENT PANEL Bluetooth Streaming Audio (BTSA) Selecting A Different Audio Device Music can be streamed from your cellular phone to the 1. Press the PHONE button to begin. Uconnect® phone system. 2. After the ⬙Ready⬙ prompt and following the beep, say Controlling BTSA Using Radio Buttons ⬙Setup⬙, then say ⬙Select Audio Devices⬙. To enter BTSA mode, press either “AUX” button on the 3.
UNDERSTANDING YOUR INSTRUMENT PANEL 389 Browse Browsing is not available on a Bluetooth Streaming Audio (BTSA) device. Only the current song that is playing will display info. UCONNECT® MULTIMEDIA — VIDEO ENTERTAINMENT SYSTEM (VES™) — If Equipped 4 Getting Started • Screen(s) located in the overhead console: Unfold the overhead LCD screen(s) by pushing the button on the overhead console behind the screen(s). Video Entertainment System (VES™) • Cycle the ignition to the ON or ACC position.
390 UNDERSTANDING YOUR INSTRUMENT PANEL • Turn on the Player (if equipped on Dual Screen Sys- Blu-ray Player tem) by pushing the Power button, located on the far Play A Blu-ray Disc left, or by pressing the button on the Remote Control. To view a Blu-ray insert the disc into the Blu-ray VES™ • When the Video Screen(s) are open and a DVD/Blu- disc Player. Playback will begin automatically after the ray Disc is inserted into the VES™ player, the screen(s) Blu-ray is recognized by the disc drive.
UNDERSTANDING YOUR INSTRUMENT PANEL 391 Using the Remote Control • Select an audio channel (Channel 1 for 2nd row screen and Channel 2 for 3rd row screen), then press the source key and select VES™ Disc from the menu. • Press popup/menu key to navigate disc menu and options. 4 NOTE: Due to the size of the content on a Blu-ray disc, the disc may not start playing immediately. Play Video Games Connect the video game console to the Auxiliary RCA input jacks or HDMI port, located on the left side behind 1.
392 UNDERSTANDING YOUR INSTRUMENT PANEL When connecting an external source to the AUX input, be sure to follow the standard color coding for the VES™ jacks: NOTE: Certain high-end video games, such as Playstation3 and XBox360 will exceed the power limit of the vehicle’s Power Inverter. Refer to the Power Inverter section in your vehicle’s Owner’s Manual for more information. Ensure the Remote Control and Headphone switch is on Channel 1. Using The Remote Control 1.
UNDERSTANDING YOUR INSTRUMENT PANEL 393 3. Touch the 1 soft-key and then touch either AUX 1 or AUX 2 in the VES column (depending which AUX input 1. Press the MENU hard-key on the radio faceplate. is used). To exit press the back arrow soft-key at the top 2. Touch the Rear VES soft-key to display the Rear VES of the screen. Controls. If a channel list is displayed, press the HIDE LIST soft-key to display the Rear VES Controls screen.
394 UNDERSTANDING YOUR INSTRUMENT PANEL Listen To An Audio Source On Channel 2 While A Video Is Playing On Channel 1 Ensure the Remote Control and Headphone switch is on Channel 2. Using The Remote Control 1. Press the SOURCE button on the Remote Control and the Mode Select Screen will display, unless a video is playing then only a small banner will appear on the bottom of the screen. 2.
UNDERSTANDING YOUR INSTRUMENT PANEL 395 3. To listen to an audio source on Channel 2 while a video is playing on Channel 1, touch the 2 soft-key and choose 1. Press the MENU hard-key on the radio faceplate. an audio source. To exit touch the back arrow soft-key at 2. Touch the Rear VES soft-key to display the Rear VES the top left of the left screen. Controls. If a channel list is displayed, press the HIDE LIST soft-key to display the Rear VES Controls screen.
396 UNDERSTANDING YOUR INSTRUMENT PANEL 3. To watch a DVD on Screen 1 for second row passengers, ensure the Remote Control and Headphone NOTE: Typically there are two different ways to operate switch is on Channel 1. the features of the Video Entertainment System (VES™). 4. To watch a DVD on Screen 2 for third row passengers, • The Remote Control ensure the Remote Control and Headphone switch is • The Touch-Screen Radio (If Equipped) on Channel 2.
UNDERSTANDING YOUR INSTRUMENT PANEL 397 Using The Touch-Screen Radio Controls 1. Press the MENU hard-key on the radio faceplate. 2. Touch the Rear VES soft-key to display the Rear VES Controls. If a channel list is displayed, press the HIDE LIST soft-key to display the Rear VES Controls screen. 4 Select DISC Mode On The VES™ Screen NOTE: • Channel/Screen 1 select mode information is shown on the left side of the screen. • Channel/Screen 2 select mode information is shown on the right side of the screen.
398 UNDERSTANDING YOUR INSTRUMENT PANEL 3. Touch the 1 or 2 soft-key and then the DISC soft-key in Play A DVD Using The VES™ Player (If Equipped) the MEDIA column. To exit touch the back arrow at 1. Insert the DVD with the label facing up. The VES™ the top left of the screen. player automatically selects the appropriate mode after the disc is recognized and starts playing the DVD.
UNDERSTANDING YOUR INSTRUMENT PANEL 399 Using The Remote Control NOTE: • Channel/Screen 1 select mode information is shown on the left side of the screen. 2. While looking at Screen 1 or 2, highlight VES DISC by either pressing Up/Down/Left/Right buttons or by • Channel/Screen 2 select mode information is shown repeatedly pressing the SOURCE button, then press on the right side of the screen. ENTER/OK on the Remote Control. • The VES™ will retain the last setting when turned off. 1.
400 UNDERSTANDING YOUR INSTRUMENT PANEL Using The Touch-Screen Radio Controls 1. Press the MENU hard-key on the radio faceplate. 3. Touch the 1 or 2 soft-key and then the DISC soft-key in the VES column. To exit touch the back arrow soft-key at the top left of the screen. 2. Touch the Rear VES soft-key to display the Rear VES Controls. If a channel list is displayed, touch the HIDE LIST soft-key to display the Rear VES Controls screen.
UNDERSTANDING YOUR INSTRUMENT PANEL 401 NOTE: Play A Blu-ray Disc Using The Blu-ray Player (If Equipped) • To view a DVD on the radio press the RADIO/MEDIA hard-key, on the radio faceplate, then touch the DISC 1. Insert the Blu-ray disc with the label facing up. The Blu-ray player automatically selects the appropriate tab soft-key and then the VIEW VIDEO soft-key. mode after the disc is recognized and starts playing • Viewing a DVD on the Touch-Screen radio screen is the Blu-ray disc.
402 UNDERSTANDING YOUR INSTRUMENT PANEL Using The Remote Control Using The Touch-Screen Radio Controls 1. Press the SOURCE button on the Blu-ray player Re- 1. mote Control. 2. 2. While looking at Screen 1 or 2, highlight Blu-ray by either pressing Up/Down/Left/Right buttons or by repeatedly pressing the SOURCE button, then press OK on the Remote Control. 3. NOTE: Press the MENU hard-key on the radio faceplate. Touch the Rear VES™ soft-key to display the Rear VES™ Controls.
UNDERSTANDING YOUR INSTRUMENT PANEL 403 • Viewing a Blu-ray Disc on the Touch-Screen radio 2. While looking at the video screen, either press Up/ Down/Left/Right on the Remote Control to highlight screen is not available in all states/provinces, and the the desired audio source or repeatedly press the vehicle must be stopped, and the shift lever must be in SOURCE button on the remote until the desired audio the PARK position for vehicles with automatic transsource appears on the screen. mission.
404 UNDERSTANDING YOUR INSTRUMENT PANEL 3. To listen to an audio source on Channel 2 while a video is playing on Channel 1, touch the 2 soft-key and choose 1. Press the MENU hard-key on the radio faceplate. an audio source. To exit touch the back arrow soft-key at 2. Touch the Rear VES soft-key to display the Rear VES the top left of the left screen. Controls. If a channel list is displayed, press the HIDE LIST soft-key to display the Rear VES Controls screen.
UNDERSTANDING YOUR INSTRUMENT PANEL 405 • Selecting a video source on Channel 2, the video source will display on the third row screen or Screen 2 • VES is able to transmit two channels of stereo audio and can be heard on Channel 2. and video simultaneously. • The 2nd row screen and 3rd row screen of the Video • The Blu-ray Disc Player can play CDs, DVDs and Entertainment System can play two separate discs Blu-ray Discs.
406 UNDERSTANDING YOUR INSTRUMENT PANEL VES™ Remote Control – If Equipped Controls And Indicators 1. Power – Turns the screen and wireless headphone transmitter for the selected Channel on or off. To hear audio while the screen is closed, press the Power button to turn the headphone transmitter on. 2. Channel Selector Indicators – When a button is pressed, the currently affected channel or channel button is illuminated momentarily. 3. Light – Turns the remote control backlighting on or off.
UNDERSTANDING YOUR INSTRUMENT PANEL 407 4. Channel/Screen Selector Switch - Indicates which 7. POP UP/MENU – Press to return to the main menu of channel is being controlled by the remote control. a DVD disc, to select a satellite audio channel from the When the selector switch is in the Channel 1 position, Station list, or select playback modes (SCAN/ the remote controls the functionality of headphone RANDOM for a CD). Channel 1 (right side of the screen). When the selector 8.
408 UNDERSTANDING YOUR INSTRUMENT PANEL 11. MUTE – Press to mute the headphone audio output 16. BACK – When navigating in menu mode, press to return to the previous screen. When navigating a for the selected channel. DVDs disc menu, the operation depends on the disc’s 12. SLOW – If Equipped – Press to slow playback of a contents. DVD disc. Press play (䉴) to resume normal play. 17. 䉳䉳 – In radio modes, press to seek to the previous 13. STATUS – If Equipped – Press to display the current tunable station.
UNDERSTANDING YOUR INSTRUMENT PANEL 409 Blu-ray Player Remote Control – If Equipped Controls And Indicators 1. Power – Turns the screen and wireless headphone transmitter for the selected Channel on or off. To hear audio while the screen is closed, press the Power button to turn the headphone transmitter on. 2. Channel Selector Indicators – When a button is pressed, the currently affected channel or channel button is illuminated momentarily. 3. SOURCE – Press to enter Source Selection screen.
410 UNDERSTANDING YOUR INSTRUMENT PANEL 5. 䉴 – Press to navigate menus. 11. KEYPAD – Press to navigate chapters or titles. 6. SETUP – Press to access the Blu-ray Setup menu 12. ▪ (Stop) – Stops disc play. screen. When a disc is loaded in the Blu-ray player (if equipped) and the VES™ mode is selected and the 13. 䉳䉳 – Press and release to jump to the previous audio track or video chapter.
UNDERSTANDING YOUR INSTRUMENT PANEL 411 Remote Control Storage The video screen(s) come with a built in storage compartment for the remote control which is accessible when the screen is opened. To remove the remote, use your index finger to pull and rotate the remote towards you. Do not try to pull the remote straight down as it will be very difficult to remove.
412 UNDERSTANDING YOUR INSTRUMENT PANEL Locking The Remote Control Replacing The Remote Control Batteries All remote control functionality can be disabled as a parental control feature. The remote control requires two AAA batteries for operation. To replace the batteries: • To disable the Remote Control from making any • Locate the battery compartment on the back of the changes, press the Video Lock button on the DVD remote, then slide the battery cover downward. player (if equipped).
UNDERSTANDING YOUR INSTRUMENT PANEL 413 Headphones Operation The headphones receive two separate channels of audio using an infrared transmitter from the video screen. Front seat occupants receive some headphone audio coverage to allow them to adjust the headphone volume for the young rear seat occupants that may not be able to do so for themselves.
414 UNDERSTANDING YOUR INSTRUMENT PANEL Blu-ray Headphones Operation The headphones receive two separate channels of audio using an infrared transmitter from the video screen. Front seat occupants receive some headphone audio coverage to allow them to adjust the headphone volume for the young rear seat occupants that may not be able to do so for themselves.
UNDERSTANDING YOUR INSTRUMENT PANEL 415 • When both switches are on Channel 2, the Remote is controlling Channel 2 and the headphones are tuned to The headphone power indicator and controls are located the audio of the VES™ Channel 2. on the right ear cup. 2. Press the SOURCE button on the remote control. NOTE: The rear video system must be turned on before sound can be heard from the headphones. To conserve 3.
416 UNDERSTANDING YOUR INSTRUMENT PANEL How Long Does the Coverage Last? This warranty lasts Each set of headphones requires two AAA batteries for as long as you own the Product. operation. To replace the batteries: What Does This Warranty Cover? Except as specified • Locate the battery compartment on the left ear cup of the below, this warranty covers any Product that in normal headphones, and then slide the battery cover down- use is defective in workmanship or materials.
UNDERSTANDING YOUR INSTRUMENT PANEL 417 INDIRECT, INCIDENTAL, CONSEQUENTIAL, EXEMPLARY, PUNITIVE OR OTHER DAMAGES OF ANY KIND OR NATURE WHATSOEVER. Some states and jurisdictions may not allow the exclusion or limitation of incidental or consequential damages, so the above limitation may not apply to you. This warranty gives you specific legal rights. You may also have other rights, which vary from jurisdiction to jurisdiction.
418 UNDERSTANDING YOUR INSTRUMENT PANEL If the radio functions (FM, AM, or SAT) are in the shared mode with the VES™, only the radio is able to control the radio functions. In this case, VES™ can share the radio mode, but not change stations until the radio mode is changed to a mode that is different from the VES™ selected radio mode. When shared, the radio has priority over the VES™ or all radio modes (FM, AM, and SAT).
UNDERSTANDING YOUR INSTRUMENT PANEL 419 Information Mode Display 4. Channel 2 Mode 5. Channel 2 Shared Status 6. Channel 2 Audio Only/Mute 7. Channel 1 ENTER/OK Button Action 8. Channel 2 ENTER/OK Button Action 9. Clock 10. Video Lock 11. Not Available / Error 12. Disc Changer Status Information Mode Video Screen Display 1. Channel 1 Mode 2. Channel 1 Shared Status 3.
420 UNDERSTANDING YOUR INSTRUMENT PANEL Numeric Keypad Menu When the display for either Channel 1 or Channel 2 shows DIRECT TUNE, pressing the remote control’s OK button activates a numeric keypad menu. This screen makes it easy to enter a specific tuner frequency, satellite channel, or track number. To enter the desired digit: 1. Press the remote control’s navigation buttons (䉱, 䉲, 䉴, 䉳) to navigate to the desired digit. 2.
UNDERSTANDING YOUR INSTRUMENT PANEL 421 Station List Menu Disc Menu When listening to Satellite audio, pressing the remote control’s POP UP/MENU button displays a list of all available channels. Navigate this list using the remote control’s navigation buttons (䉱, 䉲) to find the desired station, press the remote control’s ENTER/OK button to tune to that station. To jump through the list more quickly, navigate to the Page Up and Page Down icons on the screen.
422 UNDERSTANDING YOUR INSTRUMENT PANEL Display Settings Listening To Audio With The Screen Closed When watching a video source (DVD Video with the disc in Play mode, Aux Video, etc.), pressing the remote control’s SETUP button activates the Display Settings menu. These settings control the appearance of the video on the screen. The factory default settings are already set for optimum viewing, so there is no need to change these settings under normal circumstances.
UNDERSTANDING YOUR INSTRUMENT PANEL 423 Disc Formats • CD: CD-DA, VCD, CD-TEXT The VES™ DVD player is capable of playing the follow- • DVD/CD: MP3, WMA, AAC, DivX (versions 3 – 6) ing types of discs (12 cm or 8 cm diameter): profile 3.
424 UNDERSTANDING YOUR INSTRUMENT PANEL If you increase the volume level to account for this To help avoid playback problems, use the following change in level, remember to lower the volume before guidelines when recording discs. changing the disc or to another mode. • Open sessions are ignored. Only sessions that are closed are playable.
UNDERSTANDING YOUR INSTRUMENT PANEL 425 ⬙.WMA⬙. To prevent incorrect playback, do not use If you are still having trouble writing a disc that is playable in the VES™ DVD player, check with the disc these extensions for any other types of files. recording software publisher for more information about • For MP3 files, only version 1 ID3 tag data (such as burning playable discs. artist name, track title, album, etc.) are supported.
426 UNDERSTANDING YOUR INSTRUMENT PANEL • To change the current file, use the remote control’s or skipping forward 1.0 to 3.0 seconds at a time. If the end DVD player’s 䉱 button to advance to the next file, or of the disc is reached, the DVD player will return to the the 䉲 button to return to the start of the current or beginning of the disc and attempt to play the start of the first track. previous file.
UNDERSTANDING YOUR INSTRUMENT PANEL 427 Display Other Language Setup All of the Language settings have a special ⬙Other⬙ setting to accommodate languages other than Japanese or English. These languages are selected using a special four-digit code. To enter a new language code, activate the DVD Setup Menu.
428 UNDERSTANDING YOUR INSTRUMENT PANEL digit, press the remote control’s Right cursor button to Rating and Password Setup select the next digit. Repeat this digit selection sequence The Rating and Password settings work together to for all four digits. control the types of DVDs that your family watches. Most • When the entire four-digit code is entered, press the DVD-Video discs have a rating (from 1 to 8) assigned to remote control’s ENTER/OK button.
UNDERSTANDING YOUR INSTRUMENT PANEL 429 The default rating is Level 8 (play all discs without a To set the password, activate the DVD Setup Menu and password) and the default password is 0000. follow these additional instructions: • Using the remote control Left and Right cursor buttons, select the Rating tab. • Highlight ⬙Change Password⬙, and then press the remote control’s ENTER/OK button. • Enter the current password.
430 UNDERSTANDING YOUR INSTRUMENT PANEL • After the four-digit password is entered, press the remote To set the rating, activate the DVD Setup Menu and control’s ENTER/OK button to accept the change. follow these additional instructions: • Using the remote control’s Left and Right cursor buttons, select the Rating tab. • Highlight ⬙Change Rating⬙, and then press the remote control’s ENTER/OK button. • Enter the current password.
UNDERSTANDING YOUR INSTRUMENT PANEL 431 Product Agreement Software This product contains software licensed under GNU General Public License (GPL) or GNU Lesser General Public License (LGPL), etc. You have the right of acquisition, modification, and distribution of the source code of the GPL/LGPL software. You may download Source Code from the following website at no charge. URL: http://www.embedded-carmultimedia.
432 UNDERSTANDING YOUR INSTRUMENT PANEL • THIS PRODUCT IS LICENSED UNDER THE VC-1 PATENT PORTFOLIO LICENSE FOR THE PERSONAL AND NON-COMMERCIAL USE OF A CONSUMER TO (i) ENCODE VIDEO IN COMPLIANCE WITH THE VC-1 STANDARD (⬙VC-1 VIDEO⬙) AND/OR (ii) DECODE VC-1 VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED IN A PERSONAL AND NON-COMMERCIAL ACTIVITY AND/OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSED TO PROVIDE VC-1 VIDEO. NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY OTHER USE.
UNDERSTANDING YOUR INSTRUMENT PANEL 433 DTS is a registered trademark and the DTS logos, patents issued and pending as well as copyright and Symbol and DTS 2.0 Channel are trademarks of DTS, trade secret protection for certain aspects of such techInc. © 1996-2007 DTS, Inc. All Rights Reserved. nology. Cinavia is a trademark of Verance Corporation. Copyright 2004-2010 Verance Corporation. All rights • Manufactured under license from Dolby Laboratories. reserved by Verance.
434 UNDERSTANDING YOUR INSTRUMENT PANEL DivX®, DivX Certified® and associated logos are trade- STEERING WHEEL AUDIO CONTROLS — marks of Rovi Corporation or its subsidiaries and are IF EQUIPPED used under license. Trademark • Blu-ray Disc™, Blu-ray™ and the logos are trademarks of the Blu-ray Disc Association. • Java is a registered trademark of Oracle and/or its affiliates.
UNDERSTANDING YOUR INSTRUMENT PANEL 435 The right-hand rocker switch has a pushbutton in the center, and controls the volume and mode of the sound system. Pressing the top of the rocker switch will increase the volume. Pressing the bottom of the rocker switch will decrease the volume. Pressing the center button changes the operation of the radio from AM to FM, or to CD mode, depending on which radio is in the vehicle.
436 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: If you experience difficulty in playing a particular disc, it may be damaged (i.e., scratched, reflective coating To keep a CD/DVD in good condition, take the following removed, a hair, moisture or dew on the disc) oversized, precautions: or have protection encoding. Try a known good disc 1. Handle the disc by its edge; avoid touching the surface. before considering disc player service. CD/DVD DISC MAINTENANCE 2.
UNDERSTANDING YOUR INSTRUMENT PANEL 437 The primary control for the rear blower is on the front climate control unit located on the instrument panel. The Climate Control system allows you to regulate the When the front control is in any position other than rear, temperature, amount, and direction of air circulating the front control operates all the rear functions. throughout the vehicle.
438 UNDERSTANDING YOUR INSTRUMENT PANEL 2. Rear Blower Control — If Equipped • Use this control to regulate the amount of air forced through the rear system in any mode you select. The rear blower speed increases as you move the control to the right from the “O” (Off) position. There are seven blower speeds. To allow the rear overhead control, turn blower knob fully to the left, past The ⬙O⬙ off position into the “REAR” control position. 3.
UNDERSTANDING YOUR INSTRUMENT PANEL 439 position. Blower control should be left in the ⬙ON⬙ 7. Front Defrost Mode position to allow the climate control to either warm or Air is directed through the windshield and side cool the vehicle. window demist outlets. Use Defrost mode with 4. Rear Temperature Control — If Equipped maximum blower and temperature settings for best • Provides temperature control for the rear cabin. Turn windshield and side window defrosting.
440 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: • You can turn off the heated mirror feature at anytime by pressing the rear window defroster switch a second time. • To prevent excessive battery drain, use the rear window defroster only when the engine is operating. CAUTION! (Continued) • Do not use scrapers, sharp instruments, or abrasive window cleaners on the interior surface of the window. • Keep all objects a safe distance from the window. 9.
UNDERSTANDING YOUR INSTRUMENT PANEL 441 • In order to prevent fogging, when the Recirculation button is pressed and the mode control is set to Panel, • If the Recirculation button is pressed when the system the A/C will engage automatically. is in Defrost mode the Recirculation LED indicator will flash 3 times to indicate Recirculation mode is not • The A/C can be deselected manually without disturballowed. ing the mode control selection. NOTE: • In Floor and Mix mode the system will turn off 10.
442 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: For maximum airflow to the rear, the center instrument panel outlets can be directed toward the rear Air is directed through the floor outlets with a small seat passengers. amount through the defrost and side window deEconomy Mode mist outlets. 11. Floor Mode Button If ECONOMY mode is desired, press the A/C button to turn off the indicator light and the A/C compressor. Air is directed through the panel and floor outlets.
UNDERSTANDING YOUR INSTRUMENT PANEL 443 Rear Manual Climate Control — If Equipped The Rear Manual Climate Control system has floor air outlets at the rear of the right side sliding door, and overhead outlets at each outboard rear seating position. The unit provides warm or cool air through the floor and upper outlets. The rear blower and temperature controls for the rear seat passengers are located in the headliner, near the center of the vehicle.
444 UNDERSTANDING YOUR INSTRUMENT PANEL Rear Blower Control Rear Temperature Control The rear blower control knob can be manually set to off, or any fixed blower speed, by rotating the knob from low to high. This allows the rear seat occupants to control the volume of air circulated in the rear of the vehicle. To change the temperature in the rear of the vehicle, rotate the temperature knob counterclockwise to lower the temperature, and clockwise to increase the temperature.
UNDERSTANDING YOUR INSTRUMENT PANEL 445 Rear Mode Control Auto Mode NOTE: In many temperature positions, the Bi-Level mode is designed to provide cooler air out of the headliner outlets and warmer air from the floor outlets. • The rear system automatically maintains the correct mode and comfort level desired by the rear seat Floor Mode occupants. Air comes from the floor outlets. Headliner Mode Recirculation Control Air comes from the outlets in the headliner.
446 UNDERSTANDING YOUR INSTRUMENT PANEL The Three-Zone ATC system automatically maintains the interior comfort level desired by the driver and all passengers. The system automatically adjusts the air temperature, • Front Three-Zone ATC allows both driver and front the airflow volume, amount of outside air recirculation and passenger seat occupant, and rear seat occupants to the airflow direction. This maintains a comfortable temselect individual comfort settings. perature, even under changing conditions.
UNDERSTANDING YOUR INSTRUMENT PANEL 447 1. Air Conditioning (A/C) Button 5. Front Auto Indicator Press and release to change the current Air Conditioning This indicates when the system is in Front Auto mode. (A/C) setting, the indicator illuminates when A/C is ON. 6. Auto Indicator Performing this function will cause the ATC to switch This indicates when the system is in Auto mode. into manual mode. 2. Left Front Seat Occupant Temperature Display 7.
448 UNDERSTANDING YOUR INSTRUMENT PANEL 9. Passenger Temperature Control Up/Down Button 12. Auto Temperature Control Button Provides the passenger with independent temperature Controls airflow temperature, distribution, volume, and control. Push the top button for warmer temperatures or the amount of air recirculation automatically. Press and the lower button for cooler temperature settings. release to select. Refer to “Automatic Operation” for more information. Performing this function will cause 10.
UNDERSTANDING YOUR INSTRUMENT PANEL 449 15. Mode Control Button Controlling The Rear Climate Controls From The Front ATC Panel Press and release to select between Modes (Panel, BiLevel, Floor, Mix). Performing this function will cause the The Three-Zone ATC system allows for adjustment of the rear climate controls from the front ATC panel. ATC to switch into manual mode. 16.
450 UNDERSTANDING YOUR INSTRUMENT PANEL 3. Blower Control Display This display shows the current Blower speed selection. 4. Rear Auto Indicator This indicates when the system is in Rear Auto mode. Automatic Operation Front ATC Panel Rear Control Display 1. Press the AUTO button on the front ATC Panel and the words Front Auto will illuminate in the front ATC display, along with two temperatures for the driver and front passenger. The system will then automatically regulate the amount of airflow. 2.
UNDERSTANDING YOUR INSTRUMENT PANEL 451 3. When the system is set up for your comfort level, it is Rear Mode Control not necessary to change the settings. You will experi- Headliner Mode ence the greatest efficiency by simply allowing the Air comes from the outlets in the headliner. Each system to function automatically. of these outlets can be individually adjusted to NOTE: direct the flow of air.
452 UNDERSTANDING YOUR INSTRUMENT PANEL The blower fan speed can be set to any fixed speed by This system offers a full complement of manual override adjusting the blower control outer dial. The fan will now features. The AUTO symbol in the front ATC display will operate at a fixed speed until additional speeds are be turned off when the system is being used in the selected. This allows the front occupants to control the volume of air circulated in the vehicle and cancel the manual mode. Auto mode.
UNDERSTANDING YOUR INSTRUMENT PANEL 453 Bi-Level Mode Mix Mode Air comes from the instrument panel outlets, floor Air comes from the floor, defrost and side window outlets and defrost outlets. A slight amount of demist outlets. This mode works best in cold or air is also directed through the side window demister snowy conditions. It allows you to stay comfortable, outlets. while keeping the windshield clear.
454 UNDERSTANDING YOUR INSTRUMENT PANEL Air Conditioning (A/C) Recirculation Control When outside air contains smoke, odors, or • The Air Conditioning (A/C) button allows the operahigh humidity, or if rapid cooling is desired, tor to manually activate or deactivate the air condiyou may wish to recirculate interior air by tioning system. When in A/C mode and the ATC is set pressing the Recirculation control button. Reto a cool temperature, dehumidified air flows through the air outlets.
UNDERSTANDING YOUR INSTRUMENT PANEL 455 Rear Automatic Temperature Control (ATC) — If Equipped The rear ATC system is located in the headliner, near the center of the vehicle. The rear ATC system has floor air outlets at the rear of the right side sliding door, and overhead outlets at each outboard rear seating position. The system provides heated air through the floor outlets or cool, dehumidified air through the headliner outlets.
456 UNDERSTANDING YOUR INSTRUMENT PANEL 1. Press the Rear Temperature Lock button on the front NOTE: ATC panel. This turns off the Rear Temperature Lock • It is not necessary to move the temperature settings for icon in the rear temperature knob. cold or hot vehicles. The system automatically adjusts the temperature, mode and fan speed to provide 2. Rotate the Rear Blower, Rear Temperature and the comfort as quickly as possible. Rear Mode Control knobs to suit your comfort needs. 3.
UNDERSTANDING YOUR INSTRUMENT PANEL 457 Rear Blower Control Rear Temperature Control The rear blower control knob can be manually set to off, or any fixed blower speed, by rotating the knob from low to high. This allows the rear seat occupants to control the volume of air circulated in the rear of the vehicle. To change the temperature in the rear of the vehicle, rotate the temperature knob counterclockwise to lower the temperature, and clockwise to increase the temperature.
458 UNDERSTANDING YOUR INSTRUMENT PANEL Headliner Mode Summer Operation The engine cooling system in air conditioned vehicles must be protected with a high-quality antifreeze coolant to provide proper corrosion protection and to protect against engine overheating. A solution of 50% ethylene glycol antifreeze coolant and 50% water is recommended. Bi-Level Mode Refer to “Maintenance Procedures” in “Maintaining Your Air comes from both the headliner outlets and the Vehicle” for proper coolant selection.
UNDERSTANDING YOUR INSTRUMENT PANEL 459 Vacation/Storage Outside Air Intake Before you store your vehicle, or keep it out of service (i.e., vacation) for two weeks or more, run the air conditioning system at idle for about five minutes, in fresh air with the blower setting on high. This will ensure adequate system lubrication to minimize the possibility of compressor damage when the system is started again.
STARTING AND OPERATING CONTENTS 䡵 STARTING PROCEDURES . . . . . . . . . . . . . . . .465 䡵 AUTOMATIC TRANSMISSION . . . . . . . . . . . .472 ▫ Automatic Transmission . . . . . . . . . . . . . . . .465 ▫ Key Ignition Park Interlock. . . . . . . . . . . . . . .474 ▫ Keyless Enter-N-Go™ – If Equipped . . . . . . . .467 ▫ Brake/Transmission Shift Interlock System . . .474 ▫ Normal Starting. . . . . . . . . . . . . . . . . . . . . . .468 ▫ Fuel Economy (ECON) Mode . . . . . . . . . . . . .
462 STARTING AND OPERATING 䡵 DRIVING THROUGH WATER . . . . . . . . . . . . .486 ▫ Hill Start Assist (HSA) . . . . . . . . . . . . . . . . .501 ▫ Flowing/Rising Water . . . . . . . . . . . . . . . . . .486 䡵 TIRE SAFETY INFORMATION . . . . . . . . . . . . .504 ▫ Shallow Standing Water . . . . . . . . . . . . . . . . .486 ▫ Tire Markings . . . . . . . . . . . . . . . . . . . . . . . .504 䡵 POWER STEERING . . . . . . . . . . . . . . . . . . . . .488 ▫ Tire Identification Number (TIN). . . . . . . . . . .
STARTING AND OPERATING 463 ▫ Snow Tires . . . . . . . . . . . . . . . . . . . . . . . . . .520 䡵 TIRE PRESSURE MONITOR SYSTEM (TPMS) . . .529 ▫ Spare Tire Matching Original Equipped Tire And Wheel – If Equipped. . . . . . . . . . . . . . . .520 ▫ Compact Spare Tire – If Equipped . . . . . . . . .521 ▫ Full Size Spare – If Equipped . . . . . . . . . . . . .522 ▫ Limited-Use Spare – If Equipped . . . . . . . . . .522 ▫ Tire Spinning . . . . . . . . . . . . . . . . . . . . . . . .523 ▫ Tread Wear Indicators .
464 STARTING AND OPERATING 䡵 FLEXIBLE FUEL — IF EQUIPPED . . . . . . . . . . .542 ▫ Fuel Filler Cap (Gas Cap) . . . . . . . . . . . . . . .546 ▫ E-85 General Information . . . . . . . . . . . . . . .542 ▫ Loose Fuel Filler Cap Message . . . . . . . . . . . .548 ▫ Ethanol Fuel (E-85) . . . . . . . . . . . . . . . . . . . .544 䡵 VEHICLE LOADING . . . . . . . . . . . . . . . . . . . .549 ▫ Fuel Requirements . . . . . . . . . . . . . . . . . . . .544 ▫ Vehicle Certification Label . . . . . . . . . . . . .
STARTING AND OPERATING 465 STARTING PROCEDURES WARNING! (Continued) Before starting your vehicle, adjust your seat, adjust the inside and outside mirrors, fasten your seat belt, and if present, instruct all other occupants to buckle their seat belts. WARNING! • When leaving the vehicle, always remove the key fob from the ignition and lock your vehicle. • Never leave children alone in a vehicle, or with access to an unlocked vehicle.
466 STARTING AND OPERATING CAUTION! Damage to the transmission may occur if the following precautions are not observed: • Do not shift from REVERSE, PARK, or NEUTRAL into any forward gear when the engine is above idle speed. • Shift into PARK only after the vehicle has come to a complete stop. • Shift into or out of REVERSE only after the vehicle has come to a complete stop and the engine is at idle speed. • Before shifting into any gear, make sure your foot is firmly on the brake pedal.
STARTING AND OPERATING 467 Keyless Enter-N-Go™ – If Equipped 3. Press firmly on the center of the button to secure it into position. This feature allows the driver to operate the ignition switch with the push Removing The Button of a button, as long as the ENGINE 1. The ENGINE START/STOP button can be removed START/STOP button is installed and from the ignition switch for key fob use. the Remote Start/Keyless Enter-NGo™ FOBIK is in the passenger com- 2.
468 STARTING AND OPERATING Normal Starting Using The ENGINE START/STOP Button To Turn Off The Engine Using ENGINE START/STOP Button 1. The transmission must be in PARK or NEUTRAL. 1. Place the shift lever in PARK, then press and release the ENGINE START/STOP button. 2. Press and hold the brake pedal while pressing the ENGINE START/STOP button once. 2. The ignition switch will return to the OFF position. 3.
STARTING AND OPERATING 469 NOTE: If the ignition switch is left in the ACC or RUN • Starting with the ignition switch in the OFF position: (engine not running) position and the transmission is in • Press the ENGINE START/STOP button once to PARK, the system will automatically time out after change the ignition switch to the ACC position (EVIC 30 minutes of inactivity and the ignition will switch to the displays “IGNITION MODE ACCESSORY”), OFF position.
470 STARTING AND OPERATING If Engine Fails To Start WARNING! (Continued) WARNING! • Never pour fuel or other flammable liquid into the throttle body air inlet opening in an attempt to start the vehicle. This could result in flash fire causing serious personal injury. • Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transmission cannot be started this way.
STARTING AND OPERATING 471 3. Press and release the ENGINE START/STOP button The starter motor will disengage automatically in 10 seconds. Once this occurs, release the accelerator pedal, turn once. the ignition switch to the LOCK position, wait 10 to The starter motor will engage automatically, run for 15 seconds, then repeat the “Normal Starting” procedure. 10 seconds, and then disengage.
472 STARTING AND OPERATING ENGINE BLOCK HEATER — IF EQUIPPED The engine block heater warms the engine, and permits quicker starts in cold weather. Connect the cord to a standard 110-115 Volt AC electrical outlet with a grounded, three-wire extension cord. The engine block heater must be plugged in at least one hour to have an adequate warming effect on the engine. The engine block heater cord is routed under the hood on the driver’s side of the vehicle.
STARTING AND OPERATING 473 WARNING! WARNING! (Continued) • It is dangerous to shift out of PARK or NEUTRAL if the engine speed is higher than idle speed. If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in reverse. You could lose control of the vehicle and hit someone or something. Only shift into gear when the engine is idling normally and your foot is firmly pressing the brake pedal.
474 STARTING AND OPERATING Key Ignition Park Interlock Brake/Transmission Shift Interlock System This vehicle is equipped with a Key Ignition Park Interlock which requires the shift lever to be placed in PARK before the ignition switch can be turned to the LOCK/ OFF position. The key fob can only be removed from the ignition when the ignition is in the LOCK/OFF position, and the shift lever is locked in PARK whenever the ignition switch is in the LOCK/OFF position.
STARTING AND OPERATING 475 When the Fuel Economy (ECON) Mode is engaged, the vehicle control systems will change the following: • The transmission will upshift sooner and downshift later. • The transmission will skip select gears during shifts to allow the engine to operate at lower speeds. • The torque converter clutch will engage at lower engine speeds and remain on longer. • The engine idle speed will be lower. Fuel Economy Mode Switch • The overall driving performance will be more conservative.
476 STARTING AND OPERATING Six-Speed Automatic Transmission The shift lever position display (located in the instrument cluster) indicates the transmission gear range. You must press the brake pedal to move the shift lever out of PARK (Refer to “Brake/Transmission Shift Interlock System” in this section). To drive, move the shift lever from PARK or NEUTRAL to the DRIVE position. The electronically-controlled transmission provides a precise shift schedule.
STARTING AND OPERATING 477 The transmission shift lever has only PARK, REVERSE, NEUTRAL, and DRIVE shift positions. Manual downshifts can be made using the Electronic Range Select (ERS) shift control (described later in this section). Moving the shift lever to the left or right (–/+) while in the DRIVE position will select the highest available transmission gear, and will display that gear in the instrument cluster as 6, 5, 4, 3, 2, 1.
478 STARTING AND OPERATING WARNING! WARNING! (Continued) • Never use the PARK position as a substitute for the parking brake. Always apply the parking brake fully when parked to guard against vehicle movement and possible injury or damage. • Your vehicle could move and injure you and others if it is not completely in PARK. Check by trying to move the shift lever out of PARK with the brake pedal released. Make sure the transmission is in PARK before leaving the vehicle.
STARTING AND OPERATING 479 WARNING! (Continued) CAUTION! • Never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking brake, brake pedal or the shift lever.
480 STARTING AND OPERATING The following indicators should be used to ensure that NEUTRAL you have engaged the shift lever into the PARK position: Use this range when the vehicle is standing for prolonged • When shifting into PARK, firmly move the transmis- periods with the engine running. The engine may be sion all the way forward and to the left until it stops started in this range. Apply the parking brake and shift the transmission into PARK if you must leave the vehicle. and is fully seated.
STARTING AND OPERATING 481 CAUTION! Towing the vehicle, coasting, or driving for any other reason with the transmission in NEUTRAL can cause severe transmission damage. Refer to “Recreational Towing” in “Starting And Operating” and “Towing A Disabled Vehicle” in “What To Do In Emergencies” for further information. DRIVE This range should be used for most city and highway driving. It provides the smoothest upshifts and downshifts, and the best fuel economy.
482 STARTING AND OPERATING Transmission Limp Home Mode 3. Turn the ignition switch to the LOCK/OFF position. Transmission function is monitored electronically for abnormal conditions. If a condition is detected that could result in transmission damage, Transmission Limp Home Mode is activated. In this mode, the transmission remains in third gear regardless of which forward gear is selected. PARK, REVERSE, and NEUTRAL will continue to operate. The Malfunction Indicator Light (MIL) may be illuminated.
STARTING AND OPERATING 483 current gear in the instrument cluster, and maintain that gear as the top available gear. Once in ERS mode, tapping The Electronic Range Select (ERS) shift control allows the the shift lever to the left (-) or right (+) will change the top driver to limit the highest available gear when the shift available gear. lever is in the DRIVE position.
484 STARTING AND OPERATING NOTE: To select the proper gear position for maximum deceleration (engine braking), tap the shift lever to the left (-) repeatedly as the vehicle slows. The transmission will shift to the range from which the vehicle can best be slowed down. Torque Converter Clutch A feature designed to improve fuel economy has been included in the automatic transmission on your vehicle. A clutch within the torque converter engages automatically at calibrated speeds.
STARTING AND OPERATING 485 DRIVING ON SLIPPERY SURFACES Traction Acceleration When driving on wet or slushy roads, it is possible for a wedge of water to build up between the tire and road surface. This is hydroplaning and may cause partial or complete loss of vehicle control and stopping ability.
486 STARTING AND OPERATING DRIVING THROUGH WATER Shallow Standing Water Driving through water more than a few inches/centi- Although your vehicle is capable of driving through meters deep will require extra caution to ensure safety shallow standing water, consider the following Caution and prevent damage to your vehicle. and Warning before doing so. Flowing/Rising Water WARNING! Do not drive on or across a road or path where water is flowing and/or rising (as in storm run-off).
STARTING AND OPERATING 487 CAUTION! (Continued) WARNING! • Driving through standing water may cause damage to your vehicle’s drivetrain components. Always inspect your vehicle’s fluids (i.e., engine oil, transmission, axle, etc.) for signs of contamination (i.e., fluid that is milky or foamy in appearance) after driving through standing water. Do not continue to operate the vehicle if any fluid appears contaminated, as this may result in further damage.
488 STARTING AND OPERATING POWER STEERING The standard power steering system will give you good vehicle response and increased ease of maneuverability in tight spaces. The system will provide mechanical steering capability if power assist is lost. This is due to the cold, thick fluid in the steering system. This noise should be considered normal, and it does not in any way damage the steering system.
STARTING AND OPERATING 489 Power Steering Fluid Check Checking the power steering fluid level at a defined service interval is not required. The fluid should only be checked if a leak is suspected, abnormal noises are apparent, and/or the system is not functioning as anticipated. Coordinate inspection efforts through an authorized dealer. CAUTION! Do not use chemical flushes in your power steering system as the chemicals can damage your power steering components.
490 STARTING AND OPERATING PARKING BRAKE Before leaving the vehicle, make sure that the parking brake is fully applied and place the shift lever in the PARK position. The foot operated parking brake is positioned below the lower left corner of the instrument panel. To apply the park brake, firmly push the park brake pedal fully. To release the parking brake, press the park brake pedal a second time and let your foot up as you feel the brake disengage.
STARTING AND OPERATING 491 NOTE: • When the parking brake is applied and the automatic transmission is placed in gear, the “Brake Warning Light” will flash. If vehicle speed is detected, a chime will sound to alert the driver. Fully release the parking brake before attempting to move the vehicle. • This light only shows that the parking brake is applied. It does not show the degree of brake application.
492 STARTING AND OPERATING WARNING! (Continued) • Be sure the parking brake is fully disengaged before driving; failure to do so can lead to brake failure and a collision. • Always fully apply the parking brake when leaving your vehicle, or it may roll and cause damage or injury. Also be certain to leave the transmission in PARK. Failure to do so may allow the vehicle to roll and cause damage or injury.
STARTING AND OPERATING 493 • Brake pedal pulsations • A slight drop or fall away of the brake pedal at the end of the stop WARNING! • The Anti-Lock Brake System contains sophisticated electronic equipment that may be susceptible to interference caused by improperly installed, or high output radio transmitting equipment. This interference can cause possible loss of anti-lock braking capability. Installation of such equipment should be performed by qualified professionals.
494 STARTING AND OPERATING Anti-Lock Brake Warning Light The “Anti-Lock Brake Warning Light” monitors the anti-lock brake system. The light will come on when the ignition switch is turned to the ON position and may stay on for as long as four seconds. If the “Anti-Lock Brake Warning Light” remains on or comes on while driving, it indicates that the anti-lock portion of the brake system is not functioning and that service is required.
STARTING AND OPERATING 495 and apply as little throttle as possible. Be sure to adapt your speed and driving to the prevailing road conditions, The Traction Control System (TCS) monitors the amount and do not switch off the ESC or TCS. of wheel spin of each of the driven wheels. If wheel spin is detected, brake pressure is applied to the slipping WARNING! wheel(s) and engine power is reduced, to provide enhanced acceleration and stability.
496 STARTING AND OPERATING Brake Assist System (BAS) The Brake Assist System (BAS) is designed to optimize the vehicle’s braking capability during emergency braking maneuvers. The system detects an emergency braking situation by sensing the rate and amount of brake application, and then applies optimum pressure to the brakes. This can help reduce braking distances. The BAS complements the ABS. Applying the brakes very quickly results in the best BAS assistance.
STARTING AND OPERATING 497 Electronic Stability Control (ESC) The Electronic Stability Control (ESC) enhances directional control and stability of the vehicle under various driving conditions. ESC corrects for over/under steering of the vehicle by applying the brake of the appropriate wheel to assist in counteracting the over/under steer condition. Engine power may also be reduced to help the vehicle maintain the desired path.
498 STARTING AND OPERATING Light” will be illuminated. When in the “Partial Off” mode, ESC will operate without engine torque manageThe “ESC Off” switch is located in the center ment. This mode is intended to be used if the vehicle is in switch bank, next to the hazard flasher switch. deep snow, sand or gravel conditions and more wheel spin than ESC would normally allow is required to gain traction. To turn ESC on again, momentarily press the ESC On “ESC Off” switch.
STARTING AND OPERATING 499 running. If the “ESC Activation/Malfunction Indicator Light” comes on continuously with the engine running, a • Trailer Sway control (TSC) is disabled when the malfunction has been detected in the ESC system. If this ESC system is in the ⴖPartial Offⴖ mode.
500 STARTING AND OPERATING NOTE: Trailer Sway Control (TSC) • The “ESC Activation/Malfunction Indicator Light” TSC uses sensors in the vehicle to recognize an excesand the “ESC OFF Indicator Light” come on momen- sively swaying trailer and will take the appropriate actions to attempt to stop the sway. The system may tarily each time the ignition switch is turned ON.
STARTING AND OPERATING 501 WARNING! If TSC activates while driving, slow the vehicle down, stop at the nearest safe location, and adjust the trailer load to eliminate trailer sway. Hill Start Assist (HSA) The HSA system is designed to assist the driver when starting a vehicle from a stop on a hill. HSA will maintain the level of brake pressure the driver applied for a short period of time after the driver takes their foot off of the brake pedal.
502 STARTING AND OPERATING WARNING! There may be situations on minor hills (i.e., less than 8%), with a loaded vehicle, or while pulling a trailer, when the system will not activate and slight rolling may occur. This could cause a collision with another vehicle or object. Always remember the driver is responsible for braking the vehicle. Disabling/Enabling HSA For vehicles not equipped with the EVIC, perform the following steps: NOTE: You must complete Steps 1 through 8 within 90 seconds. 1.
STARTING AND OPERATING 503 7. Press the “ESC Off” switch (located in the lower switch Towing With HSA bank below the climate controls) four times within HSA will provide assistance when starting on a grade 20 seconds. The “ESC Activation/Malfunction Indicator when pulling a trailer. Light” should turn on and turn off two times. 8. Rotate the steering wheel back to center and then an additional half-turn to the right. 9. Turn the ignition switch to the OFF position and then back to the ON position.
504 STARTING AND OPERATING WARNING! (Continued) • HSA is not a parking brake. If you stop the vehicle on a hill without putting the transmission in PARK and using the parking brake, it will roll down the hill and could cause a collision with another vehicle or object. Always remember to use the parking brake while parking on a hill, and that the driver is responsible for braking the vehicle.
STARTING AND OPERATING 505 • Temporary spare tires are spares designed for temporary emergency use only. Temporary high pressure • P (Passenger) - Metric tire sizing is based on U.S. compact spare tires have the letter “T” or “S” molded design standards. P-Metric tires have the letter “P” into the sidewall preceding the size designation. molded into the sidewall preceding the size designaExample: T145/80D18 103M. tion. Example: P215/65R15 95H. • High flotation tire sizing is based on U.S.
506 STARTING AND OPERATING Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ⴖ....blank....ⴖ = Passenger car tire based on European design standards LT = Light truck tire based on U.S. design standards T or S = Temporary spare tire 31 = Overall diameter in inches (in) 215 = Section width in millimeters (mm) 65 = Aspect ratio in percent (%) — Ratio of section height to section width of tire 10.
STARTING AND OPERATING 507 EXAMPLE: R = Construction code — ⬙R⬙ means radial construction — ⬙D⬙ means diagonal or bias construction 15 = Rim diameter in inches (in) Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions — The maximum speed corresponding to the speed symbol should only be achieved und
508 STARTING AND OPERATING EXAMPLE: Load Identification: ⴖ....blank....
STARTING AND OPERATING 509 EXAMPLE: DOT MA L9 ABCD 0301 DOT = Department of Transportation — This symbol certifies that the tire is in compliance with the U.S.
510 STARTING AND OPERATING Tire Terminology And Definitions Term B-Pillar Cold Tire Inflation Pressure Maximum Inflation Pressure Recommended Cold Tire Inflation Pressure Tire Placard Definition The vehicle B-Pillar is the structural member of the body located behind the front door. Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or driven less than 1 mile (1.6 km) after sitting for a three hour period.
STARTING AND OPERATING 511 Tire Loading And Tire Pressure Tire And Loading Information Placard Tire And Loading Information Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar or the rear edge of the driver’s side door.
512 STARTING AND OPERATING To determine the maximum loading conditions of your vehicle, locate the statement “The combined weight of occupants and cargo should never exceed XXX lbs or XXX kg” on the Tire and Loading Information placard. Loading The combined weight of occupants, cargo/luggage and The vehicle maximum load on the tire must not exceed trailer tongue weight (if applicable) should never exceed the load carrying capacity of the tire on your vehicle. You the weight referenced here.
STARTING AND OPERATING 513 4. The resulting figure equals the available amount of NOTE: cargo and luggage load capacity. For example, if • The following table shows examples on how to calcu“XXX” amount equals 1,400 lbs (635 kg) and there will late total load, cargo/luggage, and towing capacities be five 150 lb (68 kg) passengers in your vehicle, the of your vehicle with varying seating configurations amount of available cargo and luggage load capacity and number and size of occupants.
514 STARTING AND OPERATING
STARTING AND OPERATING 515 WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.
516 STARTING AND OPERATING WARNING! (Continued) • Unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • Always drive with each tire inflated to the recommended cold tire inflation pressure. Economy Ride Comfort And Vehicle Stability Proper tire inflation contributes to a comfortable ride. Over-inflation produces a jarring and uncomfortable ride.
STARTING AND OPERATING 517 Tire Inflation Pressures The proper cold tire inflation pressure is listed on the driver’s side “B” Pillar or rear edge of the driver’s side door. At least once a month: • Check and adjust tire pressure with a good quality pocket-type pressure gauge. Do not make a visual judgement when determining proper inflation. Tires may look properly inflated even when they are underinflated. • Inspect tires for signs of tire wear or visible damage.
518 STARTING AND OPERATING Check tire pressures more often if subject to a wide range Tire Pressures For High Speed Operation of outdoor temperatures, as tire pressures vary with The manufacturer advocates driving at safe speeds and temperature changes. within posted speed limits. Where speed limits or condiTire pressures change by approximately 1 psi (7 kPa) per tions are such that the vehicle can be driven at high 12°F (7°C) of air temperature change.
STARTING AND OPERATING 519 Consult an authorized tire dealer for tire repairs and additional information. Radial Ply Tires WARNING! Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly. The instability could cause a collision. Always use radial ply tires in sets of four. Never combine them with other types of tires.
520 STARTING AND OPERATING Summer Or Three Season Tires – If Equipped Snow tires generally have lower speed ratings than what was originally equipped with your vehicle and should not be operated at sustained speeds over 75 mph (120 km/h). For speeds above 75 mph (120 km/h) refer to original equipment or an authorized tire dealer for recommended safe operating speeds, loading and cold tire inflation pressures.
STARTING AND OPERATING 521 of your vehicle. This spare tire may be used in the tire rotation for your vehicle. If your vehicle has this option refer to an authorized tire dealer for the recommended tire rotation pattern. Compact Spare Tire – If Equipped The compact spare is for temporary emergency use only.
522 STARTING AND OPERATING tire affects vehicle handling. Since it is not the same as your original equipment tire, replace (or repair) the The full size spare is for temporary emergency use only. original equipment tire and reinstall on the vehicle at the This tire may look like the originally equipped tire on the first opportunity. front or rear axle of your vehicle, but it is not. This spare tire may have limited tread life.
STARTING AND OPERATING 523 Tire Spinning Tread Wear Indicators When stuck in mud, sand, snow, or ice conditions, do not Tread wear indicators are in the original equipment tires spin your vehicle’s wheels above 30 mph (48 km/h) or to help you in determining when your tires should be for longer than 30 seconds continuously without stop- replaced. ping when you are stuck. Refer to “Freeing A Stuck Vehicle” in “What To Do In Emergencies” for further information.
524 STARTING AND OPERATING These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes 1/16 in (2 mm). When the tread is worn to the tread wear indicators, the tire should be replaced. Refer to replacement tires in this section for further information. Life Of Tire WARNING! Tires and the spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure.
STARTING AND OPERATING 525 when replacement is needed. Refer to the paragraph on equivalent replacement tires may adversely affect the “Tread Wear Indicators”. Refer to the Tire and Loading safety, handling, and ride of your vehicle. Information placard or the Vehicle Certification Label for the size designation of your tire. The Load Index and WARNING! Speed Symbol for your tire will be found on the original equipment tire sidewall.
526 STARTING AND OPERATING WARNING! (Continued) • Never use a tire with a smaller load index or capacity, other than what was originally equipped on your vehicle. Using a tire with a smaller load index could result in tire overloading and failure. You could lose control and have a collision. • Failure to equip your vehicle with tires having adequate speed capability can result in sudden tire failure and loss of vehicle control.
STARTING AND OPERATING 527 WARNING! CAUTION! (Continued) Using tires of different size and type (M+S, Snow) between front and rear axles can cause unpredictable handling. You could lose control and have a collision. CAUTION! To avoid damage to your vehicle or tires, observe the following precautions: • Because of restricted traction device clearance between tires and other suspension components, it is important that only traction devices in good condition are used.
528 STARTING AND OPERATING The suggested rotation method is the “rearward cross” shown in the following diagram. This rotation pattern The tires on the front and rear of your vehicle operate at does not apply to some directional tires that must not be different loads and perform different steering, driving, reversed. and braking functions. For these reasons, they wear at unequal rates. TIRE ROTATION RECOMMENDATIONS These effects can be reduced by timely rotation of tires.
STARTING AND OPERATING 529 The TPMS will warn the driver of a low tire pressure if the tire pressure falls below the low pressure warning The TPMS will warn the driver of a low tire pressure threshold for any reason, including low temperature based on the cold inflation tire placard pressure requireeffects, or natural air pressure loss through the tire. ments found on the tire placard label located on the driver’s-side B-pillar.
530 STARTING AND OPERATING NOTE: The vehicle may need to be driven for up to 20 minutes above 15 mph (24 km/h) to receive this information. For example, your vehicle may have a recommended cold (parked for more than three hours) tire placard pressure of 35 psi (241 kPa). If the ambient temperature is 68°F (20°C) and the measured tire pressure is 30 psi (207 kPa), a temperature drop to 20°F (-7°C) will decrease the tire pressure to approximately 26 psi (179 kPa).
STARTING AND OPERATING 531 • Seasonal temperature changes will affect tire pressure, and the TPMS will monitor the actual tire pressure in • The TPMS is not intended to replace normal tire care and the tire. maintenance, or to provide warning of a tire failure or Base System condition. NOTE: • The TPMS should not be used as a tire pressure gauge The TPMS uses wireless technology with wheel rim mounted electronic sensors to monitor tire pressure levels. while adjusting your tire pressure.
532 STARTING AND OPERATING Tire Pressure Monitoring Low Tire Pressure Warnings The “Tire Pressure Monitoring Telltale Light” will flash on and off for 75 seconds, and remain on solid when a system fault is detected. The system fault will also sound a chime. If the ignition switch is cycled, this sequence will repeat, providing the system fault still exists. The “Tire Pressure Monitoring Telltale Light” will turn off when the fault condition no longer exists.
STARTING AND OPERATING 533 4. For each subsequent ignition switch cycle, a chime will sound, the “Tire Pressure Monitoring Telltale Light” 1. The compact spare tire (if equipped) does not have a will flash on and off for 75 seconds and then remain on TPMS sensor. Therefore the TPMS will not monitor the solid. pressure in the compact spare tire. 5. Once you repair or replace the original road tire and 2.
534 STARTING AND OPERATING Premium System – If Equipped The TPMS uses wireless technology with wheel rimmounted electronic sensors to monitor tire pressure levels. Sensors mounted to each wheel as part of the valve stem transmit tire pressure readings to the Receiver Module. TPMS Low Pressure Warnings The “Tire Pressure Monitoring Telltale Light” will illuminate in the instrument cluster, and an audible chime will be activated when one or more of the four active road tire pressures are low.
STARTING AND OPERATING 535 NOTE: The vehicle may need to be driven for up to displayed instead of dashes. A system fault can occur by 20 minutes above 15 mph (24 km/h) to receive this any of the following scenarios: information. 1. Jamming due to electronic devices or driving next to facilities emitting the same radio frequencies as the SERVICE TPM SYSTEM Message TPMS sensors. The “Tire Pressure Monitoring Telltale Light” will flash on and off for 75 seconds, and remain on solid when a 2.
536 STARTING AND OPERATING pressure values still shown. This indicates that the pres- 3. After driving the vehicle for up to 20 minutes above sure values are still being received from the TPM sensors 15 mph (24 km/h), the “Tire Pressure Monitoring Telltale Light” will flash on and off for 75 seconds and but they may not be in the correct vehicle position. The then remain on solid.
STARTING AND OPERATING 537 5. Once you repair or replace the original road tire, and reinstall it on the vehicle in place of the compact spare, the TPMS will update automatically. In addition, the “Tire Pressure Monitoring Telltale Light” will turn off and the graphic in the EVIC will display a new pressure value instead of dashes (- -), as long no tire pressure is below the low pressure warning limit in any of the four active road tires.
538 STARTING AND OPERATING FUEL REQUIREMENTS 3.6L Engine Over 40 auto manufacturers worldwide have issued and endorsed consistent gasoline specifications (the Worldwide Fuel Charter, WWFC) which define fuel properties necessary to deliver enhanced emissions, performance, and durability for your vehicle. The manufacturer recommends the use of gasolines that meet the WWFC specifications if they are available.
STARTING AND OPERATING 539 Gasoline/Oxygenate Blends E-85 Usage In Non-Flex Fuel Vehicles Some fuel suppliers blend unleaded gasoline with oxy- Non-FFV vehicles are compatible with gasoline containgenates such as Ethanol. Fuels blended with oxygenates ing 10% ethanol (E10). Gasoline with higher ethanol may be used in your vehicle. content may void the vehicle’s warranty. CAUTION! DO NOT use gasoline containing Methanol or gasoline containing more than 10% Ethanol.
540 STARTING AND OPERATING To fix a Non-FFV vehicle inadvertently fueled once with MMT. Gasoline blended with MMT reduces spark plug life and reduces emissions system performance in some E-85 perform the following: vehicles. The manufacturer recommends that gasoline • drain the fuel tank (see your authorized dealer) without MMT be used in your vehicle.
STARTING AND OPERATING 541 Fuel System Cautions CAUTION! (Continued) CAUTION! Follow these guidelines to maintain your vehicle’s performance: • The use of leaded gas is prohibited by Federal law. Using leaded gasoline can impair engine performance and damage the emissions control system. • An out-of-tune engine or certain fuel or ignition malfunctions can cause the catalytic converter to overheat.
542 STARTING AND OPERATING Carbon Monoxide Warnings WARNING! (Continued) WARNING! Carbon monoxide (CO) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • Do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas, which can kill. Never run the engine in a closed area, such as a garage, and never sit in a parked vehicle with the engine running for an extended period.
STARTING AND OPERATING 543 subjects that are unique to these vehicles. Please refer to the other sections of this manual for information on features that are common between Flexible Fuel and gasoline-only powered vehicles. CAUTION! Only vehicles with the E-85 fuel filler door label can operate on E-85.
544 STARTING AND OPERATING For best results, a refueling pattern that avoids alternating E-85 is a mixture of approximately 85% fuel ethanol and between E-85 and unleaded gasoline is recommended. When you do switch fuel types it is recommended that: 15% unleaded gasoline. Ethanol Fuel (E-85) WARNING! Ethanol vapors are extremely flammable and could cause serious personal injury.
STARTING AND OPERATING 545 • Some additives used in regular gasoline are not fully compatible with E-85 and may form deposits in your engine. To eliminate driveability issues that may be caused by these deposits, a supplemental gasoline additive, such as MOPAR® Injector Cleanup or Techron may be used. Selection Of Engine Oil For Flexible Fuel Vehicles (E-85) And Gasoline Vehicles FFV vehicles operated on E-85 require specially formulated engine oils.
546 STARTING AND OPERATING Replacement Parts ADDING FUEL Many components in your Flexible Fuel Vehicle (FFV) are Fuel Filler Cap (Gas Cap) designed to be compatible with ethanol. Always be sure The gas cap is located behind the fuel filler door on the that your vehicle is serviced with correct ethanol comleft side of the vehicle. If the gas cap is lost or damaged, patible parts. be sure the replacement cap is for use with this vehicle.
STARTING AND OPERATING 547 NOTE: The driver’s side sliding door cannot be opened while the fuel door is open. This feature operates only when the sliding door is fully closed prior to opening the fuel door. CAUTION! • Damage to the fuel system or emissions control system could result from using an improper fuel tank filler tube cap (gas cap).
548 STARTING AND OPERATING NOTE: Loose Fuel Filler Cap Message • When the fuel nozzle “clicks” or shuts off, the fuel tank If the vehicle diagnostic system determines that the fuel filler cap is loose, improperly installed, or damaged, a is full. “gASCAP” message will display in the odometer or a • Tighten the fuel filler cap until you hear a “clicking” “CHECK GASCAP” message will be displayed in the sound. This is an indication that the fuel filler cap is Electronic Vehicle Information Center (EVIC).
STARTING AND OPERATING 549 VEHICLE LOADING • Gross Vehicle Weight Rating (GVWR) As required by National Highway Traffic Safety Admin- • Gross Axle Weight Rating (GAWR) front istration regulations, your vehicle has a certification label • Gross Axle Weight Rating (GAWR) rear affixed to the driver’s side door or B-Pillar. • Vehicle Identification Number (VIN) If seats are removed for carrying cargo, do not exceed the • Type of Vehicle specified GVWR and GAWR.
550 STARTING AND OPERATING Gross Axle Weight Rating (GAWR) Rim Size The GAWR is the maximum capacity of the front and rear This is the rim size that is appropriate for the tire size axles. Distribute the load over the front and rear axles listed. evenly. Make sure that you do not exceed either front or Inflation Pressure rear GAWR. This is the cold tire inflation pressure for your vehicle for all loading conditions up to full GAWR.
STARTING AND OPERATING 551 Overloading Loading The load carrying components (axle, springs, tires, wheels, etc.) of your vehicle will provide satisfactory service as long as you do not exceed the GVWR and the front and rear GAWR. To load your vehicle properly, first figure out its empty weight, axle-by-axle and side-by-side. Store heavier items down low and be sure you distribute their weight as evenly as possible. Stow all loose items securely before driving.
552 STARTING AND OPERATING exceed the GVWR. Refer to “Vehicle Loading/Vehicle In this section you will find safety tips and information Certification Label” in “Starting and Operating” for on limits to the type of towing you can reasonably do further information. with your vehicle. Before towing a trailer, carefully Gross Trailer Weight (GTW) review this information to tow your load as efficiently The GTW is the weight of the trailer plus the weight of all and safely as possible.
STARTING AND OPERATING 553 rear GAWR. Refer to “Vehicle Loading/Vehicle Certifica- Frontal Area tion Label” in “Starting and Operating” for further The frontal area is the maximum height multiplied by the information. maximum width of the front of a trailer. WARNING! It is important that you do not exceed the maximum front or rear GAWR. A dangerous driving condition can result if either rating is exceeded. You could lose control of the vehicle and have a collision.
554 STARTING AND OPERATING Weight-Carrying Hitch A weight-carrying hitch supports the trailer tongue weight, just as if it were luggage located at a hitch ball or some other connecting point of the vehicle. These kinds of hitches are the most popular on the market today and they are commonly used to tow small and medium sized trailers.
STARTING AND OPERATING 555 5 Without Weight-Distributing Hitch (Incorrect) With Weight-Distributing Hitch (Correct)
556 STARTING AND OPERATING Trailer Hitch Classification The following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition. Improper Adjustment Of Weight-Distributing Hitch (Incorrect) Class Class Class Class Trailer Hitch Classification Definitions Class Max.
STARTING AND OPERATING 557 Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/ Transmission GCWR (Gross Combined Weight Rating) 8,750 lbs (3 969 kg) Frontal Area Up to 2 persons & Luggage 3,600 lbs (1 633 kg)* 8,750 lbs (3 969 kg) 40 sq ft (3.72 sq m) 3 to 5 persons & Luggage 3,350 lbs (1 519 kg)* 8,750 lbs (3 969 kg) 40 sq ft (3.
558 STARTING AND OPERATING NOTE: The trailer tongue weight must be considered as Never exceed the maximum tongue weight stamped on part of the combined weight of occupants and cargo, and your bumper or trailer hitch. should never exceed the weight referenced on the Tire and Loading Information placard. Refer to “Tire Safety Information” in “Starting and Operating” for further information. Trailer And Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer.
STARTING AND OPERATING 559 Consider the following items when computing the Towing Requirements weight on the rear axle of the vehicle: To promote proper break-in of your new vehicle drive• The tongue weight of the trailer. train components, the following guidelines are recom• The weight of any other type of cargo or equipment mended. put in or on your vehicle. • The weight of the driver and all passengers. NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle.
560 STARTING AND OPERATING Perform the maintenance listed in the “Maintenance Schedule.” Refer to “Maintenance Schedule” for the proper maintenance intervals. When towing a trailer, never exceed the GAWR or GCWR ratings. WARNING! Improper towing can lead to a collision. Follow these guidelines to make your trailer towing as safe as possible: • Make certain that the load is secured in the trailer and will not shift during travel.
STARTING AND OPERATING 561 WARNING! (Continued) • GCWR must not be exceeded. • Total weight must be distributed between the tow vehicle and the trailer such that the following four ratings are not exceeded: 1. GVWR 2. GTW 3. GAWR 4. Trailer tongue weight rating for the trailer hitch utilized . Towing Requirements – Tires • Do not attempt to tow a trailer while using a compact spare tire. • Proper tire inflation pressures are essential to the safe and satisfactory operation of your vehicle.
562 STARTING AND OPERATING Towing Requirements – Trailer Brakes • Do not interconnect the hydraulic brake system or vacuum system of your vehicle with that of the trailer. This could cause inadequate braking and possible personal injury. • An electronically actuated trailer brake controller is required when towing a trailer with electronically actuated brakes. When towing a trailer equipped with a hydraulic surge actuated brake system, an electronic brake controller is not required.
STARTING AND OPERATING 563 WARNING! (Continued) • Towing any trailer will increase your stopping distance. When towing you should allow for additional space between your vehicle and the vehicle in front of you. Failure to do so could result in a collision. The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. Refer to the following illustrations.
564 STARTING AND OPERATING Towing Tips Before setting out on a trip, practice turning, stopping, and backing up the trailer in an area located away from heavy traffic. Automatic Transmission The DRIVE gear can be selected when towing. However, if frequent shifting occurs while in DRIVE, use the Electronic Range Select (ERS) shift control to select a lower gear range.
STARTING AND OPERATING 565 If you REGULARLY tow a trailer for more than 45 minutes of continuous operation, then change the transmission fluid and filter as specified for “police, taxi, fleet, or frequent trailer towing.” Refer to the “Maintenance Schedule” for the proper maintenance intervals. Cooling System Electronic Speed Control – If Equipped When stopped for short periods, shift the transmission into NEUTRAL and increase engine idle speed. • Do not use in hilly terrain or with heavy loads.
566 STARTING AND OPERATING RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) Towing This Vehicle Behind Another Vehicle Towing Condition Flat Tow Dolly Tow On Trailer Wheels OFF the Ground NONE Front Rear ALL All Models NOT ALLOWED OK NOT ALLOWED OK 3. Firmly apply the parking brake. Place the transmission in PARK. Recreational towing is allowed ONLY if the front wheels are OFF the ground. This may be accomplished using a 4. Properly secure the front wheels to the dolly, followtow dolly or vehicle trailer.
STARTING AND OPERATING 567 CAUTION! DO NOT flat tow this vehicle. Damage to the drivetrain will result. CAUTION! Towing this vehicle in violation of the above requirements can cause severe transmission damage. Damage from improper towing is not covered under the New Vehicle Limited Warranty.
WHAT TO DO IN EMERGENCIES CONTENTS 䡵 HAZARD WARNING FLASHERS . . . . . . . . . . .570 ▫ Jacking Instructions . . . . . . . . . . . . . . . . . . .580 䡵 IF YOUR ENGINE OVERHEATS . . . . . . . . . . . .570 ▫ Securing The Spare Tire . . . . . . . . . . . . . . . . .587 䡵 JACKING AND TIRE CHANGING . . . . . . . . . .571 ▫ Road Tire Installation . . . . . . . . . . . . . . . . . . .589 ▫ Jack Location . . . . . . . . . . . . . . . . . . . . . . . .572 䡵 JUMP-STARTING . . . . . . . . . . . . . . . . . . . .
570 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHERS IF YOUR ENGINE OVERHEATS The Hazard Warning flasher switch is located in the In any of the following situations, you can reduce the lower center area of the instrument panel. potential for overheating by taking the appropriate action. Press the switch to turn on the Hazard Warning • On the highways — slow down. flasher.
WHAT TO DO IN EMERGENCIES 571 CAUTION! Driving with a hot cooling system could damage your vehicle. If temperature gauge reads “H”, pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the “H”, turn the engine off immediately, and call for service. WARNING! You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.
572 WHAT TO DO IN EMERGENCIES WARNING! (Continued) • The jack is designed to be used as a tool for changing tires only. The jack should not be used to lift the vehicle for service purposes. The vehicle should be jacked on a firm level surface only. Avoid ice or slippery areas. Jack Location The jack, jack handle and winch handle tools are stowed behind the rear left side trim panel in the rear cargo area. Turn the two cover latches to release the cover.
WHAT TO DO IN EMERGENCIES 573 Spare Tire Removal The spare tire is stowed inside a protective cover located under the center of the vehicle between the front doors by means of a cable winch mechanism. The “spare tire drive” nut is located on the floor, under a plastic cap at the front of the floor console or under front super console forward bin liner.
574 WHAT TO DO IN EMERGENCIES To Access Spare Tire Winch Drive Nut To access the spare tire winch drive nut and lower the spare tire, you will need to refer to one of the following center console configurations. Super Console For vehicles equipped with the Super Console, the spare tire winch assembly drive nut is located beneath the console.
WHAT TO DO IN EMERGENCIES 575 1. Pull the lower drawer out from the rear of the floor console to gain clear access of the tire winch drive nut. 2. Open the front drawer to expose the storage compartment. 3. Remove the liner from the console’s storage compartment to access the spare tire winch drive nut.
576 WHAT TO DO IN EMERGENCIES Premium/Base/Cargo Center Console Spare Tire Tools Pull the Winch Cover assembly plug (if equipped) to The tool pouch contains three pieces and can be asaccess the winch drive nut. sembled into a spare tire hook; to remove the compact spare tire/cover assembly from under the vehicle, or a Winch T-handle; to raise/lower the compact spare tire/ cover assembly.
WHAT TO DO IN EMERGENCIES 577 6 Assembled T-handle A — Spare Tire Hook/T-handle B — Extension 1 C — Extension 2 Assembling The Spare Tire Hook A — Spare Tire Hook/T-handle B — Extension 1 C — Extension 2
578 WHAT TO DO IN EMERGENCIES 2. Rotate the nut to the left until the winch mechanism stops turning freely. This will allow enough slack in The spare tire is located under the vehicle beneath the the cable to allow you to pull the spare tire out from center console area. underneath the vehicle. Spare Tire Removal Instructions CAUTION! The winch mechanism is designed for use with the winch T-handle only. Use of an air wrench or other power tools is not recommended and can damage the winch. 3.
WHAT TO DO IN EMERGENCIES 579 4. Stand the tire/cover assembly upright and remove the wheel spacer by squeezing the winch retaining tabs together. Push the retainer through the spare tire to release it from the wheel. 6 Pulling Spare Tire NOTE: If either front tire is flat it may be necessary to jack up the vehicle to remove the compact spare tire/ cover assembly from under the vehicle.
580 WHAT TO DO IN EMERGENCIES Preparations For Jacking 1. Park the vehicle on a firm, level surface. Avoid ice or slippery areas. WARNING! Do not attempt to change a tire on the side of the vehicle close to moving traffic, pull far enough off the road to avoid being hit when operating the jack or changing the wheel. 2. Turn on the Hazard Warning flasher. 3. Set the parking brake. 4. Place the shift lever into PARK. 5. Turn OFF the ignition. 6.
WHAT TO DO IN EMERGENCIES 581 WARNING! (Continued) WARNING! (Continued) • Turn on the Hazard Warning flasher. • Block the wheel diagonally opposite the wheel to be raised. • Set the parking brake firmly and set an automatic transmission in PARK; a manual transmission in REVERSE. • Never start or run the engine with the vehicle on a jack. • Do not let anyone sit in the vehicle when it is on a jack. • Do not get under the vehicle when it is on a jack.
582 WHAT TO DO IN EMERGENCIES CAUTION! Do not attempt to raise the vehicle by jacking on locations other than those indicated in the Jacking Instructions for this vehicle. NOTE: Refer to the “Compact Spare Tire” section of “Tires – General Information” for information about the spare tire, its use, and operation. 1. Loosen (but do not remove) the wheel lug nuts by turning them to the left one turn while the wheel is still on the ground. Jack Locations 2.
WHAT TO DO IN EMERGENCIES 583 Rear jack locations are between a pair of down-facing Front jack location is on the sill flange of the vehicle body tabs on the sill flange of the vehicle side body. and is located 6 in (150 mm) from door edge.
584 WHAT TO DO IN EMERGENCIES NOTE: In some situations the jack may need to be 4. Raise the vehicle by turning the jack screw to the right, placed on its side in order to be pushed under the vehicle. using the swivel wrench. Raise the vehicle only until Return the jack to its correct orientation once it is under the tire just clears the surface and enough clearance is the vehicle. obtained to install the spare tire. Minimum tire lift provides maximum stability.
WHAT TO DO IN EMERGENCIES 585 CAUTION! WARNING! Be sure to mount the spare tire with the valve stem facing outward. The vehicle could be damaged if the spare tire is mounted incorrectly. To avoid the risk of forcing the vehicle off the jack, do not tighten the wheel nuts fully until the vehicle has been lowered. Failure to follow this warning may result in personal injury. NOTE: Do not install the wheel cover on the compact spare. 7. Lower the vehicle by turning the jack screw to the left.
586 WHAT TO DO IN EMERGENCIES 9. Lower the jack to its fully-closed position. WARNING! A loose tire or jack thrown forward in a collision or hard stop could endanger the occupants of the vehicle. Always stow the jack parts and the spare tire in the places provided. Have the deflated (flat) tire repaired or replaced immediately. 11. Stow the cable and wheel spacer before driving the vehicle. Reassemble the winch handle extensions to form a “T” and fit the winch T-handle over the drive nut.
WHAT TO DO IN EMERGENCIES 587 Securing The Spare Tire CAUTION! 1. Assemble the winch handle extensions to form a T-handle and fit the winch T-handle over the drive The winch mechanism is designed for use with the nut. Rotate the nut to the left until the winch mecha- winch T-handle only. Use of an air wrench or other nism stops turning freely. This will allow enough slack power tools is not recommended and can damage the in the cable to allow you to pull the wheel spacer out winch.
588 WHAT TO DO IN EMERGENCIES CAUTION! The compact spare tire/cover assembly must be used when the compact spare tire is stored. Failure to use this cover could drastically reduce the life of the compact spare tire. WARNING! Verify that both retainer tabs of the wheel spacer have been properly extended through the center of the wheel and spare tire/cover assembly.
WHAT TO DO IN EMERGENCIES 589 Road Tire Installation Vehicles Equipped With Wheel Covers 1. Mount the road tire on the axle. 2. To ease the installation process for steel wheels with wheel covers, install two lug nuts on the mounting studs which are on each side of the valve stem. Install the lug nuts with the cone shaped end of the nut toward the wheel. Lightly tighten the lug nuts.
590 WHAT TO DO IN EMERGENCIES 3. Align the valve notch in the wheel cover with the 5. Lower the vehicle to the ground by turning the jack valve stem on the wheel. Install the cover by hand, handle counterclockwise. snapping the cover over the two lug nuts. Do not use 6. Finish tightening the lug nuts. Push down on the a hammer or excessive force to install the cover. wrench while at the end of the handle for increased 4. Install the remaining lug nuts with the cone shaped leverage.
WHAT TO DO IN EMERGENCIES 591 4. Finish tightening the lug nuts. Push down on the wrench while at the end of the handle for increased 1. Mount the road tire on the axle. leverage. Tighten the lug nuts in a star pattern until 2. Install the remaining lug nuts with the cone shaped each nut has been tightened twice. The correct tightend of the nut toward the wheel. Lightly tighten the ness of each lug nut is 100 ft/lbs (135 N·m). If in doubt lug nuts.
592 WHAT TO DO IN EMERGENCIES JUMP-STARTING Preparations For Jump-Start If your vehicle has a discharged battery it can be jump- The battery in your vehicle is located on the left side of started using a set of jumper cables and a battery in the engine compartment. another vehicle or by using a portable battery booster pack. Jump-starting can be dangerous if done improperly so please follow the procedures in this section carefully.
WHAT TO DO IN EMERGENCIES 593 WARNING! • Take care to avoid the radiator cooling fan whenever the hood is raised. It can start anytime the ignition switch is ON. You can be injured by moving fan blades. • Remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact. You could be seriously injured. • Batteries contain sulfuric acid that can burn your skin or eyes and generate hydrogen gas which is flammable and explosive.
594 WHAT TO DO IN EMERGENCIES CAUTION! WARNING! Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle. Do not connect the cable to the negative post (-) of the discharged battery. The resulting electrical spark could cause the battery to explode and could result in personal injury. 1. Connect the positive (+) end of the jumper cable to the positive (+) post of the discharged vehicle. 5.
WHAT TO DO IN EMERGENCIES 595 8. Disconnect the opposite end of the positive (+) jumper FREEING A STUCK VEHICLE cable from the positive (+) post of the booster battery. If your vehicle becomes stuck in mud, sand or snow, it 9. Disconnect the positive (+) end of the jumper cable can often be moved using a rocking motion. Turn the steering wheel right and left to clear the area around the from the positive (+) post of the discharged vehicle. front wheels.
596 WHAT TO DO IN EMERGENCIES NOTE: Press the ⬙ESC Off⬙ switch, to place the Electronic Stability Control (ESC) system in ⬙Partial Off⬙ mode before rocking the vehicle. Refer to “Electronic Brake Control System” in “Starting and Operating” for further information.Once the vehicle has been freed, press the ⬙ESC Off⬙ switch again to restore ⬙ESC On⬙ mode.
WHAT TO DO IN EMERGENCIES 597 3. Using a small screwdriver or similar tool, remove the 4. Press and maintain firm pressure on the brake pedal. shift lever override access cover (located near the top 5. Insert the screwdriver or similar tool into the access right of the shift lever in the instrument panel). hole, and push and hold the override release lever forward. 6. Move the shift lever to the NEUTRAL position. 7. The vehicle may then be started in NEUTRAL. 8.
598 WHAT TO DO IN EMERGENCIES TOWING A DISABLED VEHICLE Towing Condition Flat Tow Wheel lift Wheels OFF the Ground NONE Rear Flatbed Front ALL Proper towing or lifting equipment is required to prevent damage to your vehicle. Use only tow bars and other equipment designed for this purpose, following equipment manufacturer’s instructions. Use of safety chains is mandatory. Attach a tow bar or other towing device to main structural members of the vehicle, not to bumpers or associated brackets.
WHAT TO DO IN EMERGENCIES 599 CAUTION! • Do not use sling type equipment when towing. Damage to the fascia will occur. • When securing the vehicle to a flatbed truck, do not attach to front or rear suspension components. Damage to your vehicle may result from improper towing. • Do not push or tow this vehicle with another vehicle as damage to the bumper fascia and transmission may result. With Ignition Key The manufacturer recommends towing your vehicle with all four wheels OFF the ground using a flatbed.
600 WHAT TO DO IN EMERGENCIES CAUTION! Towing faster than 25 mph (40 km/h) or farther than 15 mi (24 km) with front wheels on the ground can cause severe transmission damage. Such damage is not covered by the New Vehicle Limited Warranty. CAUTION! Towing this vehicle in violation of the above requirements can cause severe transmission damage. Damage from improper towing is not covered under the New Vehicle Limited Warranty.
MAINTAINING YOUR VEHICLE CONTENTS 䡵 ENGINE COMPARTMENT — 3.6L . . . . . . . . . .603 ▫ Engine Air Cleaner Filter . . . . . . . . . . . . . . . .612 䡵 ONBOARD DIAGNOSTIC SYSTEM — OBD II . . .604 ▫ Exhaust System . . . . . . . . . . . . . . . . . . . . . .612 ▫ Loose Fuel Filler Cap Message . . . . . . . . . . . .605 ▫ Maintenance-Free Battery . . . . . . . . . . . . . . .615 䡵 EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS . . . . . . . . . . . . .605 ▫ Air Conditioner Maintenance . . . . . . . . . . .
602 MAINTAINING YOUR VEHICLE ▫ Appearance Care And Protection From Corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . .631 ▫ Cleaning The Instrument Panel Cupholders . . . .637 䡵 FUSES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .638 ▫ Totally Integrated Power Module . . . . . . . . . .638 䡵 VEHICLE STORAGE . . . . . . . . . . . . . . . . . . . .646 䡵 REPLACEMENT BULBS . . . . . . . . . . . . . . . . .647 䡵 BULB REPLACEMENT . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 603 ENGINE COMPARTMENT — 3.
604 MAINTAINING YOUR VEHICLE Although your vehicle will usually be drivable and not need towing, see your authorized dealer for service as Your vehicle is equipped with a sophisticated onboard soon as possible. diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic CAUTION! transmission control systems.
MAINTAINING YOUR VEHICLE 605 Loose Fuel Filler Cap Message EMISSIONS INSPECTION AND MAINTENANCE If the vehicle diagnostic system determines that the fuel PROGRAMS filler cap is loose, improperly installed, or damaged, a In some localities, it may be a legal requirement to pass “gASCAP” message will display in the odometer or a an inspection of your vehicle’s emissions control system. “CHECK GASCAP” message will be displayed in the Failure to pass could prevent vehicle registration.
606 MAINTAINING YOUR VEHICLE Your vehicle has a simple ignition key-actuated test, • The MIL will not flash at all and will remain fully which you can use prior to going to the test station. To illuminated until you turn OFF the ignition or start the engine. This means that your vehicle’s OBD II system check if your vehicle’s OBD II system is ready, you must is ready and you can proceed to the I/M station. do the following: 1.
MAINTAINING YOUR VEHICLE 607 NOTE: Intentional tampering with emissions control systems may void your warranty and could result in civil Use of genuine MOPAR® parts for normal/scheduled penalties being assessed against you. maintenance and repairs is highly recommended to ensure the designed performance. Damage or failures WARNING! caused by the use of non-MOPAR® parts for maintenance and repairs will not be covered by the manufac- You can be badly injured working on or around a turer’s warranty.
608 MAINTAINING YOUR VEHICLE MAINTENANCE PROCEDURES CAUTION! (Continued) The pages that follow contain the required maintenance services determined by the engineers who designed your vehicle. Besides those maintenance items specified in the fixed maintenance schedule, there are other components which may require servicing or replacement in the future.
MAINTAINING YOUR VEHICLE 609 Engine Oil Checking Oil Level To assure proper engine lubrication, the engine oil must be maintained at the correct level. Check the oil level at regular intervals, such as every fuel stop. The best time to check the engine oil level is about five minutes after a fully warmed engine is shut OFF or before starting the engine after it has sat overnight. CAUTION! Overfilling or underfilling will cause oil aeration, or loss of oil pressure. This could damage your engine.
610 MAINTAINING YOUR VEHICLE Engine Oil Selection For best performance and maximum protection under all types of operating conditions, the manufacturer only recommends engine oils that are API Certified and meet the requirements of Chrysler Material Standard MS-6395. American Petroleum Institute (API) Engine Oil Identification Symbol CAUTION! Do not use chemical flushes in your engine oil as the chemicals can damage your engine. Such damage is not covered by the New Vehicle Limited Warranty.
MAINTAINING YOUR VEHICLE 611 environment. Contact your authorized dealer, service station or governmental agency for advice on how and You may use synthetic engine oils provided the recomwhere used oil and oil filters can be safely discarded in mended oil quality requirements are met, and the recomyour area. mended maintenance intervals for oil and filter changes are followed.
612 MAINTAINING YOUR VEHICLE Engine Air Cleaner Filter Engine Air Cleaner Filter Selection Refer to the “Maintenance Schedule” for the proper The quality of replacement engine air cleaner filters varies maintenance intervals. considerably. Only high quality filters should be used to assure most efficient service. MOPAR® engine air cleaner filters are a high quality filter and are recommended. WARNING! The air induction system (air cleaner, hoses, etc.
MAINTAINING YOUR VEHICLE 613 into the passenger compartment. In addition, have the exhaust system inspected each time the vehicle is raised for lubrication or oil change. Replace as required. WARNING! • Exhaust gases can injure or kill. They contain carbon monoxide (CO), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing CO, refer to “Safety Tips/Exhaust Gas” in “Things To Know Before Starting Your Vehicle” for further information.
614 MAINTAINING YOUR VEHICLE Under normal operating conditions, the catalytic con- To minimize the possibility of catalytic converter damverter will not require maintenance. However, it is im- age: portant to keep the engine properly tuned to assure • Do not shut off the engine or interrupt the ignition, proper catalyst operation and prevent possible catalyst when the transmission is in gear and the vehicle is in damage. motion.
MAINTAINING YOUR VEHICLE 615 Maintenance-Free Battery WARNING! (Continued) Your vehicle is equipped with a maintenance-free battery. You will never have to add water, nor is periodic maintenance required. WARNING! • Battery fluid is a corrosive acid solution and can burn or even blind you. Do not allow battery fluid to contact your eyes, skin, or clothing. Do not lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area immediately with large amounts of water.
616 MAINTAINING YOUR VEHICLE CAUTION! (Continued) CAUTION! • If a “fast charger” is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery. Do not use a “fast charger” to provide starting voltage. Do not use chemical flushes in your air conditioning system as the chemicals can damage your air conditioning components. Such damage is not covered by the New Vehicle Limited Warranty.
MAINTAINING YOUR VEHICLE 617 WARNING! (Continued) • The air conditioning system contains refrigerant under high pressure. To avoid risk of personal injury or damage to the system, adding refrigerant or any repair requiring lines to be disconnected should be done by an experienced technician. Refrigerant Recovery And Recycling R-134a Air Conditioning Refrigerant is a hydrofluorocarbon (HFC) that is endorsed by the Environmental Protection Agency and is an ozone-saving product.
618 MAINTAINING YOUR VEHICLE 4. Disengage the two retaining tabs that secure the filter 6. Install the A/C air filter with the arrow on the filter cover to the HVAC housing, and remove the cover. pointing toward the floor. When installing the filter cover, make sure the retaining tabs fully engage the cover. CAUTION! The A/C air filter is identified with an arrow to indicate airflow direction through the filter. Failure to properly install the filter will result in the need to replace it more often. 7.
MAINTAINING YOUR VEHICLE 619 Body Lubrication Windshield Wiper Blades Locks and all body pivot points, including such items as seat tracks, door hinge pivot points and rollers, liftgate, tailgate, sliding doors and hood hinges, should be lubricated periodically with a lithium based grease, such as MOPAR® Spray White Lube to assure quiet, easy operation and to protect against rust and wear.
620 MAINTAINING YOUR VEHICLE Adding Washer Fluid The fluid reservoir for the windshield washers and the rear window washer is shared. It is located in the engine compartment and should be checked at regular intervals. Fill the reservoir with windshield washer solvent (not radiator antifreeze) and operate the system for a few seconds to flush out any residual water. The washer fluid reservoir will hold a full gallon of fluid when the Low Washer Fluid Light illuminates.
MAINTAINING YOUR VEHICLE 621 WARNING! (Continued) • You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator. If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool. Never try to open a cooling system pressure cap when the radiator is hot. Coolant Checks Check the engine coolant (antifreeze) protection every 12 months (before the onset of freezing weather, where applicable).
622 MAINTAINING YOUR VEHICLE Cooling System – Drain, Flush, And Refill If the engine coolant (antifreeze) is dirty or contains visible sediment, clean and flush with OAT coolant (antifreeze) that meets the requirements of Chrysler Material Standard MS-12106. Refer to the “Maintenance Schedule” for the proper maintenance intervals. Selection Of Coolant Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for further information.
MAINTAINING YOUR VEHICLE 623 CAUTION! (Continued) • This vehicle has not been designed for use with propylene glycol-based engine coolant (antifreeze). Use of propylene glycol-based engine coolant (antifreeze) is not recommended. that meets the requirements of Chrysler Material Standard MS-12106.
624 MAINTAINING YOUR VEHICLE Please note that it is the owner’s responsibility to main- The cap should be inspected and cleaned if there is any tain the proper level of protection against freezing ac- accumulation of foreign material on the sealing surfaces. cording to the temperatures occurring in the area where the vehicle is operated. WARNING! NOTE: Mixing engine coolant (antifreeze) types is not recommended and can result in cooling system damage.
MAINTAINING YOUR VEHICLE 625 Disposal Of Used Engine Coolant The radiator normally remains completely full, so there is no need to remove the radiator cap unless checking for engine coolant (antifreeze) freeze point or replacing coolant. Advise your service attendant of this. As long as the engine operating temperature is satisfactory, the coolant bottle need only be checked once a month. Used ethylene glycol-based engine coolant (antifreeze) is a regulated substance requiring proper disposal.
626 MAINTAINING YOUR VEHICLE humidity accumulating on the radiator and being vapor- • Maintain engine coolant (antifreeze) concentration at a ized when the thermostat opens, allowing hot engine minimum of 50% OAT coolant (conforming to MS-12106) coolant (antifreeze) to enter the radiator. and distilled water for proper corrosion protection of your engine which contains aluminum components.
MAINTAINING YOUR VEHICLE 627 Brake System Master Cylinder – Brake Fluid Level Check In order to assure brake system performance, all brake system components should be inspected periodically. Refer to the “Maintenance Schedule” for the proper maintenance intervals. The fluid level in the master cylinder should be checked when performing underhood services, or immediately if the “Brake System Warning Light” indicates system failure.
628 MAINTAINING YOUR VEHICLE Use only manufacturer’s recommended brake fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for further information. WARNING! • Use only manufacturer’s recommended brake fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for further information. Using the wrong type of brake fluid can severely damage your brake system and/or impair its performance.
MAINTAINING YOUR VEHICLE 629 WARNING! (Continued) • Do not allow petroleum based fluid to contaminate the brake fluid. Brake seal components could be damaged, causing partial or complete brake failure. This could result in a collision. Automatic Transmission Selection Of Lubricant It is important to use the proper transmission fluid to ensure optimum transmission performance and life. Use only the manufacturer’s recommended transmission fluid.
630 MAINTAINING YOUR VEHICLE Special Additives Fluid Level Check The manufacturer strongly recommends against using The fluid level is preset at the factory and does not any special additives in the transmission. require adjustment under normal operating conditions. Routine fluid level checks are not required, therefore the Automatic Transmission Fluid (ATF) is an engineered transmission filler tube is capped and no dipstick is product and its performance may be impaired by suppleprovided.
MAINTAINING YOUR VEHICLE 631 The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion Refer to the “Maintenance Schedule” for the proper resistance built into your vehicle. maintenance intervals. What Causes Corrosion? In addition, change the fluid and filter if the transmission Corrosion is the result of deterioration or removal of is disassembled for any reason. paint and protective coatings from your vehicle.
632 MAINTAINING YOUR VEHICLE Washing • Wash your vehicle regularly. Always wash your vehicle in the shade using MOPAR® Car Wash, or a mild car wash soap, and rinse the panels completely with clear water. CAUTION! • Do not use abrasive or strong cleaning materials such as steel wool or scouring powder that will scratch metal and painted surfaces. • Use of power washers exceeding 1,200 psi (8 274 kPa) can result in damage or removal of paint and decals.
MAINTAINING YOUR VEHICLE 633 • If you detect any stone chips or scratches in the paint, Wheel And Wheel Trim Care touch them up immediately. The cost of such repairs is All wheels and wheel trim, especially aluminum and considered the responsibility of the owner. chrome plated wheels, should be cleaned regularly with • If your vehicle is damaged due to a collision or similar a mild soap and water to prevent corrosion.
634 MAINTAINING YOUR VEHICLE CAUTION! (Continued) Avoid automatic car washes that use acidic solutions or harsh brushes that may damage the wheel’s protective finish. Only MOPAR® Wheel Cleaner or equivalent is recommended. Stain Repel Fabric Cleaning Procedure – If Equipped • For grease stains, apply MOPAR® Multi-Purpose Cleaner to a clean, damp cloth and remove stain. Use a fresh, damp towel to remove soap residue. • Do not use any harsh solvents or any other form of protectants on Stain Repel products.
MAINTAINING YOUR VEHICLE 635 taken to avoid soaking your leather upholstery with any liquid. Please do not use polishes, oils, cleaning fluids, Interior trim should be cleaned starting with a damp solvents, detergents, or ammonia-based cleaners to clean cloth, a damp cloth with MOPAR® Total Clean or equivayour leather upholstery. Application of a leather condilent, then MOPAR® Spot & Stain Remover or equivalent tioner is not required to maintain the original condition. if absolutely necessary.
636 MAINTAINING YOUR VEHICLE To minimize the possibility of scratching the lenses and When cleaning the rear view mirror, spray cleaner on the reducing light output, avoid wiping with a dry cloth. To towel or rag that you are using. Do not spray cleaner remove road dirt, wash with a mild soap solution fol- directly on the mirror. lowed by rinsing.
MAINTAINING YOUR VEHICLE 637 Seat Belt Maintenance Cleaning Do not bleach, dye, or clean the belts with chemical The liner is top shelf dishwasher safe, or you may follow solvents or abrasive cleaners. This will weaken the fabric. the cleaning procedure below. Sun damage can also weaken the fabric. Soak the liner in a mixture of medium hot tap water and If the belts need cleaning, use MOPAR® Total Clean, a one teaspoon of mild liquid dish soap. Let soak for mild soap solution, or lukewarm water.
638 MAINTAINING YOUR VEHICLE FUSES Totally Integrated Power Module The Totally Integrated Power Module is located in the engine compartment near the battery. Refer to the applicable “Engine Compartment” illustration in this section. This center contains cartridge fuses and mini-fuses. A label that identifies each component may be printed or embossed on the inside of the cover.
MAINTAINING YOUR VEHICLE 639 CAUTION! • When installing the Totally Integrated Power Module cover, it is important to ensure the cover is properly positioned and fully latched. Failure to do so may allow water to get into the Integrated Power Module, and possibly result in a electrical system failure. • When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating. The use of a fuse with a rating other than indicated may result in a dangerous electrical system overload.
640 MAINTAINING YOUR VEHICLE Cavity J7 J8 J9 J10 Cartridge Fuse 30 Amp Pink MiniFuse — 40 Amp Green 40 Amp Green — 30 Amp Pink — — Description Cavity Antilock Brakes Valve/Stability Control System Power Memory Seat – If Equipped Partial Zero Emissions Vehicle Motor/Flex Fuel – If Equipped Headlamp Wash/ Manifold Tuning Valve – If Equipped J11 J12 J13 J14 J15 Cartridge Fuse 30 Amp Pink 30 Amp Pink 60 Amp Yellow 40 Amp Green 40 Amp Green MiniFuse — — — — Description Power Sliding Door Modu
MAINTAINING YOUR VEHICLE 641 Cavity J17 J18 J19 J20 J21 J22 Cartridge Fuse 40 Amp Green 20 Amp Blue 60 Amp Yellow 30 Amp Pink 20 Amp Blue 25 Amp Natural MiniFuse Description Cavity — Starter Solenoid M1 Cartridge Fuse — — M2 — — Powertrain Control Module Trans Range Radiator Fan M3 — — Front Wiper LO/HI M4 — — Front/Rear Washer M5 — — Sunroof Module MiniFuse 15 Amp Blue 20 Amp Yellow 20 Amp Yellow 10 Amp Red 25 Amp Natural Description Rear Center Brake Lamp/Brake Switch Front Fog
642 MAINTAINING YOUR VEHICLE Cavity M6 Cartridge Fuse — MiniFuse 20 Amp Yellow M7 — 20 Amp Yellow M8 — 20 Amp Yellow Description Cavity Power Outlet #1 (ACC), Rain Sensor, Cigar Lighter (Instrument Panel or with Console Rear) Power Outlet #2 (BATT/ACC SELECT) – Center Seat or with Console Rear Front Heated Seat – If Equipped M9 Cartridge Fuse — M10 — MiniFuse 20 Amp Yellow 15 Amp Blue Description Rear Heated Seat – If Equipped Ignition Off Draw — Video System, Satellite Radio, DVD, Hands-F
MAINTAINING YOUR VEHICLE 643 M11 Cartridge Fuse — M12 — M13 — Cavity M14 — MiniFuse 10 Amp Red 30 Amp Green 20 Amp Yellow 20 Amp Yellow Description Cavity Climate Control System Amplifier/Radio M15 Cartridge Fuse — M16 — 10 Amp Red M17 — 15 Amp Blue Instrument Cluster, SIREN, Clock Module, MultiFunction Control Switch – If Equipped Trailer Tow – If Equipped MiniFuse 20 Amp Yellow Description Rear View Mirror, Instrument Cluster, Multi-Function Control Switch, Tire Pressure Monitor,
644 MAINTAINING YOUR VEHICLE M18 Cartridge Fuse — M19 — M20 — Cavity M21 — M22 — MiniFuse 15 Amp Blue 25 Amp Natural 15 Amp Blue 20 Amp Yellow 10 Amp Red Description Cavity Right Tail/Park/ Run Lamp Powertrain M23 Cartridge Fuse — M24 — Instrument Cluster Interior Light, Switch Bank, Steering Column Module, Switch Steering Wheel Powertrain M25 — M26 — 10 Amp Red M27 — 10 Amp Red Horn MiniFuse 10 Amp Red 25 Amp Natural 20 Amp Yellow Description Horn Rear Wiper Fuel Pump, Diese
MAINTAINING YOUR VEHICLE 645 M28 Cartridge Fuse — M29 — M30 — M31 — M32 — Cavity MiniFuse 10 Amp Red 10 Amp Red 15 Amp Blue 20 Amp Yellow 10 Amp Red Description Cavity Powertrain, Transmission Control Module Occupant Classification Module Rear Wiper Module, Power Folding Mirror Back-Up Lamps M33 Cartridge Fuse — M34 — Airbag Module, THATCHUM – If Equipped M35 — MiniFuse 10 Amp Red 10 Amp Red 10 Amp Red Description Powertrain Park Assist, Heater Climate Control Module, Headlamp Wash,
646 MAINTAINING YOUR VEHICLE Cavity M36 M37 M38 Cartridge Fuse — — — VEHICLE STORAGE MiniFuse 20 Amp Yellow 10 Amp Red 25 Amp Natural Description Power Outlet #3 (Instrument Panel or with Console Center) Antilock Brakes, Stability Control, Stop Lamp, Fuel Pump Door Lock/Unlock Motors, Liftgate Lock/Unlock Motors The power windows are fused by a 25 Amp circuit breaker located in the Totally Integrated Power Module.
MAINTAINING YOUR VEHICLE 647 REPLACEMENT BULBS Interior Bulbs Center & Rear Dome Lamp Center & Rear Reading Lamps Front Door Courtesy Lamp Front Header Reading Lamps – If Equipped Bulb Number 578 578 578 578 Instrument Cluster Lamps Liftgate Lamp(s) Overhead Console Reading Lamps Removable Console Lamp – If Equipped Visor Vanity Lamps Bulb Number PC74 578 PC579 194 6501966 NOTE: For lighted switches, see your authorized dealer for replacement instructions.
648 MAINTAINING YOUR VEHICLE Exterior Bulbs Headlamp – (Low and High Beam Halogen) Headlamp (HID – If Equipped) Low Beam Fog Lamp – If Equipped Front Side Marker Front Park/Turn Signal Rear Turn Signal Lamp Rear Tail, Stop, and Side Marker Lamp Center High-Mounted Stop Lamp Backup Lamp License BULB REPLACEMENT Bulb Number H11 D1S H11 W5W PY27/7W or 3757A 3757A LED (Serviced at Authorized Dealer) LED (Serviced at Authorized Dealer) 3157 168 High Intensity Discharge Headlamps (HID) — If Equipped The headla
MAINTAINING YOUR VEHICLE 649 NOTE: On vehicles equipped with High Intensity Discharge (HID) headlamps, when the headlamps are turned on, there is a blue hue to the lamps. This diminishes and becomes more white after approximately 10 seconds, as the system charges. Quad Headlamps 1. Raise the hood to access the high or low beam bulbs at the rear of the headlamp housing. CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life.
650 MAINTAINING YOUR VEHICLE 1. From behind the bumper fascia, or the access panel on the air dam, twist the bulb counterclockwise, and 1. Raise the hood to access the rear of the headlamp remove bulb. housing. Front Position Lamp NOTE: Access is somewhat limited. You may have to remove the inner fender well or remove the headlamp housing for bulb replacement. 2. Twist the socket and remove from the headlamp housing, then pull the bulb out. CAUTION! Do not touch the new bulb with your fingers.
MAINTAINING YOUR VEHICLE 651 Rear Turn Signal And Backup Lamp NOTE: • If a screwdriver is used, make sure a soft material is placed between the vehicle body and tool so not to 2. Remove the tail lamp assembly by removing the two scratch the paint. screws from the inboard side. Use a fiber stick or similar tool to gently pry the light on the outboard side • The PRY location is best closest to the studs while to disengage the two ball studs. dislodging them separately. 1. Raise the liftgate. 3.
652 MAINTAINING YOUR VEHICLE Center High-Mounted Stop Lamp (CHMSL) 2. Twist and remove the socket from the lamp assembly and pull the bulb out to remove. The CHMSL uses LED lamps that are not serviceable separately. The CHMSL must be replaced as an assembly, 3. Push the bulb into the socket, twist the socket into the see your authorized dealer. lamp assembly and reinstall the lamp assembly into place ensuring the locking tab is secure.
MAINTAINING YOUR VEHICLE 653 FLUID CAPACITIES U.S. Metric Fuel (Approximate) 20 Gallons 76 Liters Engine Oil with Filter 3.6L Engine (SAE 5W-20, API Certified) 6 Quarts 5.6 Liters Cooling System * 3.6L Engine (MOPAR® Antifreeze/ 13.4 Quarts 12.6 Liters Engine Coolant 10 Year/150,000 Mile Formula or equivalent) * Includes heater and coolant recovery bottle filled to MAX level. Add 2.9 Qts (2.8 L) if equipped with a rear heater.
654 MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant Engine Oil Engine Oil Filter Spark Plugs Fuel Selection Fluid, Lubricant, or Genuine Part We recommend you use MOPAR® Antifreeze/Coolant 10 Year/150,000 Mile Formula OAT (Organic Additive Technology) meeting the requirements of Chrysler Material Standard MS-12106. We recommend you use API Certified SAE 5W-20 Engine Oil, meeting the requirements of Chrysler Material Standard MS-6395.
MAINTAINING YOUR VEHICLE 655 Chassis Component Automatic Transmission Brake Master Cylinder Power Steering Reservoir Fluid, Lubricant, or Genuine Part We recommend you ONLY use MOPAR® ATF+4® Automatic Transmission Fluid. Failure to use ATF+4® fluid may affect the function or performance of your transmission. We recommend you use MOPAR® DOT 3 and SAE J1703 should be used. If DOT 3 brake fluid is not available, then DOT 4 is acceptable.
M A I N T E N A ▫ Maintenance Chart . . . . . . . . . . . . . . . . . . . .660 N C E MAINTENANCE SCHEDULES CONTENTS 䡵 MAINTENANCE SCHEDULE . . . . . . . . . . . . .
M A I N T E N A N C E S C H E D U L E S 8 658 MAINTENANCE SCHEDULES MAINTENANCE SCHEDULE Your vehicle is equipped with an automatic oil change indicator system. The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Based on engine operation conditions, the oil change indicator message will illuminate. This means that service is required for your vehicle.
MAINTENANCE SCHEDULES 659 M • Check the tire inflation pressures and look for unusual wear or damage • Check the fluid levels of the coolant reservoir, brake master cylinder, power steering and transmission as needed • Check function of all interior and exterior lights Required Maintenance Intervals. Refer to the maintenance schedules on the following page for the required maintenance intervals. At Every Oil Change Interval As Indicated By Oil Change Indicator System: • Change oil and filter.
40,000 50,000 60,000 70,000 80,000 90,000 100,000 110,000 120,000 130,000 140,000 150,000 4 5 6 7 8 9 10 11 12 13 14 15 80,000 96,000 112,000 128,000 144,000 160,000 176,000 192,000 208,000 224,000 240,000 following pages for the required maintenance intervals.
Additional Maintenance Replace engine air filter. Replace cabin/air conditioning filter. Replace spark plugs (3.6L engine). ** Flush and replace the engine coolant at 10 years or 150,000 miles (240,000 km) whichever comes first.
S C H E D U L E S 8 Change automatic transmission fluid and filter(s) if using your vehicle for any of the following: police, taxi, fleet, or frequent trailer towing. Change automatic transmission fluid and filter(s). Inspect and replace PCV valve if necessary.
MAINTENANCE SCHEDULES 663 M WARNING! • You can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic. • Failure to properly inspect and maintain your vehicle could result in a component malfunction and effect vehicle handling and performance. This could cause an accident.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS 䡵 SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE . . . . . . . . . . . . . . . . . . .667 ▫ Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) . . . . . . . . . . . . .669 ▫ Prepare For The Appointment. . . . . . . . . . . . .667 ▫ Service Contract . . . . . . . . . . . . . . . . . . . . . .670 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . . .667 䡵 WARRANTY INFORMATION . . . . . . . . . . . . .671 ▫ Be Reasonable With Requests . .
666 IF YOU NEED CONSUMER ASSISTANCE 䡵 DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES . . . . . . . . .673 ▫ Treadwear. . . . . . . . . . . . . . . . . . . . . . . . . . .674 ▫ Traction Grades . . . . . . . . . . . . . . . . . . . . . . .674 ▫ Temperature Grades. . . . . . . . . . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE 667 SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment Be Reasonable With Requests If you list a number of items and you must have your vehicle by the end of the day, discuss the situation with the service advisor and list the items in order of priority. At many authorized dealer, you may obtain a rental vehicle at a minimal daily charge. If you need a rental, it is advisable to make these arrangements when you call for an appointment.
668 IF YOU NEED CONSUMER ASSISTANCE are most concerned that you get prompt and high quality service. The manufacturer’s authorized dealer have the facilities, factory-trained technicians, special tools, and the latest information to ensure the vehicle is fixed correctly and in a timely manner.
IF YOU NEED CONSUMER ASSISTANCE 669 Chrysler Canada Inc. Customer Center P.O. Box 1621 Windsor, Ontario N9A 4H6 Phone: (800) 465–2001 English / (800) 387–9983 French In Mexico contact: Av. Prolongacion Paseo de la Reforma, 1240 Sante Fe C.P. 05109 Mexico, D. F.
670 IF YOU NEED CONSUMER ASSISTANCE Service Contract You may have purchased a service contract for a vehicle to help protect you from the high cost of unexpected repairs after the manufacturer’s New Vehicle Limited Warranty expires. The manufacturer stands behind only the manufacturer’s service contracts. If you purchased a manufacturer’s service contract, you will receive Plan Provisions and an Owner Identification Card in the mail within three weeks of the vehicle delivery date.
IF YOU NEED CONSUMER ASSISTANCE 671 WARNING! Engine exhaust, some of its constituents, and certain vehicle components contain, or emit, chemicals known to the State of California to cause cancer and birth defects, or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain, or emit, chemicals known to the State of California to cause cancer and birth defects, or other reproductive harm.
672 IF YOU NEED CONSUMER ASSISTANCE campaign. However, NHTSA cannot become involved PUBLICATION ORDER FORMS in individual problems between you, your authorized To order the following manuals, you may use either dealer, and the manufacturer. the website or the phone numbers listed below. Visa, To contact NHTSA, you may either call the Auto Safety Mastercard, American Express, and Discover orders are Hotline toll free at 1–888–327–4236 (TTY: 1–800–424– accepted.
IF YOU NEED CONSUMER ASSISTANCE 673 Diagnostic Procedure Manuals Call toll free at: Diagnostic Procedure Manuals are filled with diagrams, charts and detailed illustrations. These practical manuals make it easy for students and technicians to find and fix problems on computer-controlled vehicle systems and features.
674 IF YOU NEED CONSUMER ASSISTANCE Treadwear Traction Grades The Treadwear grade is a comparative rating, based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half times as well on the government course as a tire graded 100.
IF YOU NEED CONSUMER ASSISTANCE 675 Temperature Grades The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
INDEX 10
678 INDEX Adding Engine Coolant (Antifreeze) . . . . . . . . . . . .623 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .546 Adding Washer Fluid . . . . . . . . . . . . . . . . . . . . . .620 Additives, Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . .540 Adjustable Pedals . . . . . . . . . . . . . . . . . . . . . . . . .238 Airbag. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79 Airbag Deployment . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 679 Automatic Transmission . . . . . . . . . . . . . . . . . . . .472 Adding Fluid . . . . . . . . . . . . . . . . . . . . . . . . . .630 Fluid and Filter Changes . . . . . . . . . . . . . . . . . .631 Fluid Change . . . . . . . . . . . . . . . . . . . . . . . . . .631 Fluid Level Check . . . . . . . . . . . . . . . . . . . . . . .630 Fluid Type . . . . . . . . . . . . . . . . . . . . . . . . . . . .629 Gear Ranges . . . . . . . . . . . . . . . . . . . . . . . . . . .477 Special Additives . . . . . .
680 INDEX Cargo Area Features . . . . . . . . . . . . . . . . . . . . . . .296 Cargo Compartment . . . . . . . . . . . . . . . . . . . . . . .296 Luggage Carrier . . . . . . . . . . . . . . . . . . . . . . . .298 Cargo (Vehicle Loading) . . . . . . . . . . . . . . . . . . . .288 Car Washes . . . . . . . . . . . . . . . . . . . . . . . . . . . . .632 Cellular Phone . . . . . . . . . . . . . . . . . . . . . . . . . . .149 Center High Mounted Stop Light . . . . . . . . . . . . . .652 Certification Label. . .
INDEX 681 Delay (Intermittent) Wipers . . . . . . . . . . . . . . . . . .232 Diagnostic System, Onboard . . . . . . . . . . . . . . . . .604 Dimmer Control . . . . . . . . . . . . . . . . . . . . . . . . . .226 Dipsticks Automatic Transmission . . . . . . . . . . . . . . . . . .630 Oil (Engine) . . . . . . . . . . . . . . . . . . . . . . . . . . .609 Power Steering . . . . . . . . . . . . . . . . . . . . . . . . .489 Disabled Vehicle Towing . . . . . . . . . . . . . . . . . . . .
682 INDEX Electrical Power Outlets. . . . . . . . . . . . . . . . Electric Remote Mirrors . . . . . . . . . . . . . . . . Electronic Brake Control System . . . . . . . . . . Brake Assist System . . . . . . . . . . . . . . . . Electronic Speed Control (Cruise Control) . . . Electronic Stability Control (ESC) . . . . . . . . . Electronic Vehicle Information Center (EVIC) . Emergency, In Case of Hazard Warning Flasher . . . . . . . . . . . . . Jacking . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 683 Exhaust Gas Caution. . . . . . . . . . . . . . . . . . . . . . . .60 Exhaust System. . . . . . . . . . . . . . . . . . . . . . . . . . .121 Exterior Lights . . . . . . . . . . . . . . . . . . . . . . . . . . .125 Fabric Care. . . . . . . . . Filler Location Fuel . . . Filters Air Cleaner . . . . . . Air Conditioning . . Engine Oil . . . . . . . Engine Oil Disposal . Flashers Hazard Warning . . . Turn Signal . . . . . . Flash-To-Pass . . . . . . . Flexible Fuel Vehicles Cruising Range . . . .
684 INDEX Additives . . . . . . . . . Clean Air . . . . . . . . . Conserving . . . . . . . . Economy Mode . . . . Ethanol . . . . . . . . . . Filler Cap (Gas Cap) . Filler Door (Gas Cap) Gasoline . . . . . . . . . . Gauge . . . . . . . . . . . Light . . . . . . . . . . . . Materials Added . . . . Methanol . . . . . . . . . Octane Rating . . . . . . Requirements . . . . . . Saver Mode . . . . . . . Tank Capacity . . . . . . Fuel, Flexible . . . . . . . . Fueling . . . . . . . . . . . . Fuel Optimizer . . .
INDEX 685 Gross Vehicle Weight Rating. . . . . . . . . . . . . . . . . .549 Hill Start Assist. . . . . . . . . . . . . . . . . . . . . . . . . . .501 GVWR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .549 Hitches Trailer Towing . . . . . . . . . . . . . . . . . . . . . . . . .556 Hands-Free Phone (Uconnect®) . . . . . . . . . . . . . . .149 HomeLink® (Garage Door Opener) . . . . . . . . . . . .260 Hood Release . . . . . . . . . . . . . . . . . . . . . . . . . . . .222 Hazard Hook, Coat.
686 INDEX Integrated Power Module (Fuses) . . . . . . . . . . . . . .638 Interior Appearance Care . . . . . . . . . . . . . . . . . . . .634 Interior Lights . . . . . . . . . . . . . . . . . . . . . . . . . . .226 Intermittent Wipers (Delay Wipers). . . . . . . . . . . . .232 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Jack Location . . . . . . . . . . . . . . . . . . . . . . . . . . . .572 Jack Operation . . . . . . . . . . . . . . . . . . . . . . . . . . .571 Jump Starting .
INDEX 687 Passing . . . . . . . . . . . . . . . . . . . . . . . . . . Center Mounted Stop . . . . . . . . . . . . . . . . . . . .652 Reading . . . . . . . . . . . . . . . . . . . . . . . . . . Daytime Running . . . . . . . . . . . . . . . . . . . . . . .225 Rear Servicing . . . . . . . . . . . . . . . . . . . . . Dimmer Switch, Headlight . . . . . . . . . . . . . . . . .226 Rear Tail . . . . . . . . . . . . . . . . . . . . . . . . . Electronic Stability Program (ESP) Indicator . . . . .
688 INDEX Load Leveling System . . . . . . . . . . . . . . . . . . . . . .298 Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35 Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35 Lubrication, Body . . . . . . . . . . . . . . . . . . . . . . . . .619 Luggage Rack (Roof Rack) . . . . . . . . . . . . . . . . . . .298 Maintenance Free Battery. . . . . . . . . . . . . . Maintenance Procedures . . . . . . . . . . . . . . Maintenance Schedule . . . . . . . . . . . .
INDEX 689 Odometer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .315 Oil Change Indicator . . . . . . . . . . . . . . . . . . . . . . .317 Oil Change Indicator, Reset . . . . . . . . . . . . . . . . . .317 Oil, Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .609 Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . .653 Change Interval . . . . . . . . . . . . . . . . . . . . . . . .609 Checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
690 INDEX Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .137 Outlet (Auxiliary Electrical Outlet) . . . . . . . . . . .272 Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .187 Sliding Door . . . . . . . . . . . . . . . . . . . . . . . . . . .49 Steering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .488 Sunroof . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .269 Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 691 Reporting Safety Defects . . . . . . . . . . . . . . . . . . . .671 Resetting Oil Change Indicator . . . . . . . . . . . . . . . .317 Restraint, Head. . . . . . . . . . . . . . . . . . . . . . . . . . .195 Restraints, Child . . . . . . . . . . . . . . . . . . . . . . . . . . .95 Rocking Vehicle When Stuck . . . . . . . . . . . . . . . . .595 Roof Rack (Luggage Rack) . . . . . . . . . . . . . . . . . . .298 Rotation, Tires . . . . . . . . . . . . . . . . . . . . . . . . . . .
692 INDEX Sentry Key Programming . . . . . . . . . . . . . . . . . . . .16 Sentry Key Replacement . . . . . . . . . . . . . . . . . . . . .16 Service Assistance . . . . . . . . . . . . . . . . . . . . . . . . .667 Service Contract . . . . . . . . . . . . . . . . . . . . . . . . . .670 Service Engine Soon Light (Malfunction Indicator) . . .321 Service Manuals . . . . . . . . . . . . . . . . . . . . . . . . . .672 Settings, Personal . . . . . . . . . . . . . . . . . . . . . . . . .347 Setting the Clock. . .
INDEX 693 Sunglasses Storage . . . . . . . . . . . . . . . . . . . . . . . .256 Sun Roof . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .269 Supplemental Restraint System - Airbag . . . . . . . . . .79 Sway Control, Trailer. . . . . . . . . . . . . . . . . . . . . . .500 Synthetic Engine Oil . . . . . . . . . . . . . . . . . . . . . . .611 System, Remote Starting . . . . . . . . . . . . . . . . . . . . .30 Tachometer. . . . . . . . . . . . . . . . . . . . . Telescoping Steering Column . . . .
694 INDEX Tread Wear Indicators . . . . Tire Safety Information . . . . . Tongue Weight/Trailer Weight Torque Converter Clutch . . . . Towing . . . . . . . . . . . . . . . . 24-Hour Towing Assistance Disabled Vehicle . . . . . . . . Guide . . . . . . . . . . . . . . . Recreational . . . . . . . . . . . Weight . . . . . . . . . . . . . . . Towing Assistance. . . . . . . . . Traction . . . . . . . . . . . . . . . . Traction Control . . . . . . . . . . Traction Control Switch . . . . .
INDEX 695 .673 Washer Adding Fluid . . . . . . . . . . . . . . . . . . . . . . . . . .620 .381 .260 Washing Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . .632 .538 Water Driving Through . . . . . . . . . . . . . . . . . . . . . . . .486 .634 Wind Buffeting. . . . . . . . . . . . . . . . . . . . . . . . . . . .48 Vanity Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . .139 Window Fogging . . . . . . . . . . . . . . . . . . . . . . . . .459 Variance, Compass . . . . . . . . . . . . . .
INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained personnel. The following must be observed during installation. The positive power connection should be made directly to the battery and fused as close to the battery as possible.
Chrysler Group LLC 13C481-126-AE 300 5th Edition Printed in U.S.A.
