chrysler.com This guide has been prepared to help you get quickly acquainted with your new Chrysler and to provide a convenient reference source for common questions. However, it is not a substitute for your Owner’s Manual. For complete operational instructions, maintenance procedures and important safety messages, please consult your Owner’s Manual, Navigation/ Media Center Manuals, Multimedia User Manual and other Warning Labels in your vehicle.
The driver’s primary responsibility is the safe operation of the vehicle. Driving while distracted can result in loss of vehicle control, resulting in a collision and personal injury. Chrysler Group LLC strongly recommends that the driver use extreme caution when using any device or feature that may take their attention off the road.
TABLE OF CONTENTS INTRODUCTION/WELCOME UTILITY Welcome From Chrysler Group LLC . . . . . . 2 Trailer Towing Weights (Maximum Trailer Weight Ratings) . . . . . . . . . . . .42 Recreational Towing (Behind Motorhome, Etc.) . . . . . . . . . . . . . . . 43 CONTROLS AT A GLANCE Driver Cockpit . . . . . . . . . . . . . . . . 4 Instrument Cluster . . . . . . . . . . . . . . 6 WHAT TO DO IN EMERGENCIES GETTING STARTED Key FOB . . . . . . . . . . . . . . Remote Start . . . . . . . . . . . . Theft Alarm . . .
INTRODUCTION/WELCOME WELCOME FROM CHRYSLER GROUP LLC Congratulations on selecting your new Chrysler Group LLC vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. Your new Chrysler Group LLC vehicle has characteristics to enhance the driver's control under some driving conditions. These are to assist the driver and are never a substitute for attentive driving. They can never take the driver's place.
INTRODUCTION/WELCOME Vehicles Sold In Canada With respect to any vehicles sold in Canada, the name Chrysler Group LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefore. WARNING! • Pedals that cannot move freely can cause loss of vehicle control and increase the risk of serious personal injury. • Always make sure that objects cannot fall into the driver foot well while the vehicle is moving.
CONTROLS AT A GLANCE DRIVER COCKPIT 04
CONTROLS AT A GLANCE 05
CONTROLS AT A GLANCE INSTRUMENT CLUSTER Warning Lights - Low Fuel Warning Light - Charging System Light** - Oil Pressure Warning Light** - Anti-Lock Brake (ABS) Light** - Airbag Warning Light** - Electronic Throttle Control (ETC) Light - Tire Pressure Monitoring System (TPMS) Light - Engine Temperature Warning Light - Transmission Temperature Warning Light - Seat Belt Reminder Light BRAKE - Brake Warning Light** - Malfunction Indicator Light (MIL)** - Electronic Stability Control (ESC) Activation/Malfunct
CONTROLS AT A GLANCE Indicators - Turn Signal Indicators - High Beam Indicator - Front Fog Light Indicator - Vehicle Security Indicator* - Cruise Indicator - Electronic Stability Control (ESC) Off Indicator - Park/Headlight ON Indicator Odometer Messages door - Door Ajar deck - Trunk Ajar HOTOIL* - Transaxle Oil Temperature Exceeds Safe Threshold * If equipped ** Bulb Check with Key On CHAngE OIL* - Change Engine Oil gASCAP - Fuel Cap Fault LoW TirE* - Low Tire Pressure TOP nOT SECUrE - Convertible Top
GETTING STARTED KEY FOB Locking And Unlocking The Doors • Press the LOCK button once to lock all the doors. Press the UNLOCK button once to unlock the driver’s door only and twice within five seconds to unlock all the doors. • All doors can be programmed to unlock on the first press of the UNLOCK button. Refer to Programmable Features in this guide. Opening The Trunk • Press the TRUNK button on the transmitter two times within five seconds to open the trunk.
GETTING STARTED WARNING! (Continued) • Keep Key Fob transmitters away from children. Operation of the Remote Start System, windows, door locks or other controls could cause serious injury or death. REMOTE START • Press the REMOTE START button x2 twice within five seconds. Pressing the REMOTE START button a third time shuts the engine off. • To drive the vehicle, press the UNLOCK button, insert the key in the ignition and turn to the ON/RUN position.
GETTING STARTED • A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Seat belt assemblies must be replaced after a collision if they have been damaged (bent retractor, torn webbing, etc.).
GETTING STARTED CHILD RESTRAINTS • Children 12 years and under should ride properly buckled up in a rear seat, if available. According to crash statistics, children are safer when properly restrained in the rear seats rather than in the front. • Every state in the United States and all Canadian provinces require that small children ride in proper restraint systems. This is the law, and you can be prosecuted for ignoring it.
GETTING STARTED • Tighten all three straps as you push the child restraint rearward and downward into the seat. Installing The Child Restraint Using The Vehicle Seat Belts • To install a child restraint, first, pull enough of the seat belt webbing from the retractor to route it through the belt path of the child restraint and slide the latch plate into the buckle. • Next, extract all the seat belt webbing out of the retractor and then allow the belt to retract into the retractor.
GETTING STARTED WARNING! (Continued) • Improper installation of a child restraint to the LATCH anchorages can lead to failure of an infant or child restraint. The child could be severely injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint. • An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child.
GETTING STARTED Recliner • Lift the recliner lever located on the outboard side of the seat, lean back and release at the desired position. Lumbar Support • The lumbar adjust lever is on the inboard side of the seatback. Rotate the lumbar adjust lever downward to increase the lumbar support or upward to decrease the lumbar support as desired. Easy Entry Lever • The Easy Entry lever is located on the upper seat belt anchor cover.
GETTING STARTED WARNING! • Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted, and you could be severely injured or killed. Only adjust a seat while the vehicle is parked. • Do not ride with the seatback reclined so that the seat belt is no longer resting against your chest. In a collision, you could slide under the seat belt and be severely injured or killed.
GETTING STARTED TILT / TELESCOPING STEERING COLUMN • The tilt/telescoping control lever is located below the steering wheel at the end of the steering column. • Push down on the lever to unlock the steering column. • To tilt the steering column, move the steering wheel upward or downward as desired. To lengthen or shorten the steering column, pull the steering wheel outward or push it inward as desired. • Pull upward on the lever to lock the column firmly in place.
OPERATING YOUR VEHICLE TURN SIGNAL/LIGHTS LEVER Headlights/Parking Lights/Automatic Headlights • Rotate the end of the lever to the first detent for parking lights headlights and the third detent for AUTO. , the second detent for • When set to AUTO, the system automatically turns the headlights on or off based on ambient light levels.
OPERATING YOUR VEHICLE WIPER/WASHER LEVER Front Wipers Intermittent, Low And High Operation • Rotate the end of the lever to the first detent position for one of five intermittent settings, the second for low wiper operation and the third detent for high wiper operation. Mist • Pull down on the lever and release when a single wipe is desired. Washer Operation • Pull the lever toward you and hold for as long as spray is desired. SPEED CONTROL • The speed control switches are located on the steering wheel.
OPERATING YOUR VEHICLE Accel/Decel • Once a speed is set, pushing the RES + button once or the SET – button once will increase or decrease the set speed approximately 1 mph (2 km/h). • Push and hold the RES + button to accelerate in 5mph (8 km/h) increments or push and hold the SET – button to decelerate in 5mph (8 km/h) increments; release the button to save the new set speed. Resume • To resume a previously selected set speed in memory, push the RES + button and release.
OPERATING YOUR VEHICLE MANUAL CLIMATE CONTROLS Air Recirculation • Use recirculation for maximum A/C operation. • For window defogging, turn the recirculation button off. • Recirculation is not allowed in defrost, floor, defrost/floor (mix) modes. AUTOMATIC TEMPERATURE CONTROLS (ATC) Automatic Operation • Turn the Mode and Blower Controls to the AUTO position. • Select the desired temperature by rotating the Temperature Control. • The system will maintain the set temperature automatically.
OPERATING YOUR VEHICLE Air Recirculation • Use recirculation for maximum A/C operation. • For window defogging, turn the air recirculation button off. • If the recirculation button is pressed while in the AUTO mode, the indicator light may flash three times to indicate the cabin air is being controlled automatically. POWER CONVERTIBLE TOP OPERATION • Before lowering the top, verify the cargo shield is perfectly positioned in the trunk. CAUTION! Do not place objects on the cargo shield.
OPERATING YOUR VEHICLE Emergency Bypass Mode (To Raise The Top Only) • This procedure is only to be used to raise the top when the top cannot be returned to the UP (raised) position by pressing the POWER TOP switch or is in a position in which the vehicle cannot be driven. Please follow these emergency bypass instructions to return the top to the UP (raised) position.
OPERATING YOUR VEHICLE WIND BUFFETING • Wind buffeting can be described as a helicopter-type percussion sound. If buffeting occurs with the rear windows open, adjust the front and rear windows together. • If buffeting occurs with the sunroof open, adjust the sunroof opening, or adjust any window. This will minimize buffeting.
ELECTRONICS YOUR VEHICLE'S SOUND SYSTEM 24
ELECTRONICS 25
ELECTRONICS NON-TOUCH-SCREEN RADIOS Media Center 130 (Sales Code RES) Media Center 130 with Satellite Radio (Sales Code RES + RSC) 26
ELECTRONICS Media Center 230 (Sales Code REQ) NOTE: Your radio may not be equipped with the Uconnect™ Voice Command and Uconnect™ Phone features. To determine if your radio has these features, press the Voice Command button on the radio. You will hear a voice prompt if you have the feature, or see a message on the radio stating “Uconnect Phone not available” if you do not. • Your radio has many features that add to the comfort and convenience of you and your passengers.
ELECTRONICS Audio Jack • The Audio Jack allows a portable device, such as an MP3 player or a cassette player, to be plugged into the radio and utilize the vehicle’s audio system, using a 3.5 mm audio cable, to amplify the source and play through the vehicle speakers. • Pressing the AUX button will change the mode to auxiliary device if the Audio Jack is connected, allowing the music from your portable device to play through the vehicle's speakers.
ELECTRONICS TOUCH-SCREEN RADIO Media Center 430/430N CD/DVD/HDD (Sales Code RBZ/RHB) NOTE: Your radio may not be equipped with the Uconnect™ Voice Command and Uconnect™ Phone features. To determine if your radio has these features, press the Voice Command button on the radio. You will hear a voice prompt if you have the feature, or see a message on the radio stating “Uconnect Phone not available” if you do not.
ELECTRONICS Clock Setting • Turn the radio on, then touch the screen where the time is displayed. • Touch the USER CLOCK soft-key (Navigation radio only). • To adjust the hours, touch either the HOUR FORWARD or HOUR BACKWARD soft-key. • To adjust the minutes, touch either the MINUTE FORWARD or MINUTE BACKWARD soft-key. • To save the new time setting, touch the screen where the word “Save” is displayed.
ELECTRONICS • Confirm your selection by touching the YES soft-key. The imported picture is now available in the MANAGE MY PICTURES screen. • In order to display the imported picture in the radio screen, touch the desired picture soft-key. • Select this picture by pressing the PICTURE VIEW soft-key. A check mark indicates the currently used picture. Cleaning Your Touch-Screen Radio • Do not spray any liquid or caustic chemicals directly on the screen.
ELECTRONICS Setting a Home Location • Touch the NAV soft-key in the upper-right corner of your radio screen to access the Navigation system. • Touch the Where To? soft-key, then touch Go Home. • Next, select from: • Enter My Address – enter an address for the location using the on-screen keyboard. • Use my current location – sets your current location as your Home Location. • Choose from Recently Found – select a location from your recently found locations.
ELECTRONICS Uconnect™ Phone • To determine if your vehicle is equipped with Uconnect™ Phone, press the Uconnect™ Phone . If your vehicle has this feature, after a couple seconds you will hear a voice button prompt. If not, you will see a message on the radio “Uconnect phone not available”. • The Uconnect™ Phone is a voice-activated, hands-free, in-vehicle communications system with Voice Command Capability (see Voice Command section).
ELECTRONICS Phonebook Edit • Press the Phone button . • (After the BEEP), say “phonebook”. • (After the BEEP), say “new entry” or “list names” or “delete”. • Follow the prompts. Receiving A Call – Accept (And End) • When an incoming call rings/is announced on Uconnect™, press the Phone button • To end a call, press the Phone button . . Mute (Or Unmute) Microphone During Call • During a call, press the Voice Command button . • (After the BEEP), say “mute” (or “mute off”).
ELECTRONICS Uconnect™ VOICE COMMAND • The Uconnect™ Voice Command system allows you to control your AM, FM radio, satellite radio, disc player, Uconnect™ Phone, a memo recorder, and supported portable media devices. The Voice Command system also provides limited capability to select and play music by artist, song, album, music, genre, or playlist from your compatible iPod® device (this capability is available for Media Center 430/430N when connected to the USB port).
ELECTRONICS iPod®/USB/MP3 CONTROL • There are many ways to play music from iPod® players or other portable devices through your vehicle's speakers. Your choices depend on what radio your vehicle is equipped with. • The radio sales code is located on the lower right side of the radio faceplate.
ELECTRONICS WARNING! Do not plug in or remove the iPod® or external device while driving. Failure to follow this warning could result in a collision. ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) • The EVIC features a driver interactive display that is located in the instrument cluster. Pressing the controls on the left side of the steering wheel allows the driver to select vehicle information and Personal Settings. For additional information, refer to Programmable Features in this guide.
ELECTRONICS PROGRAMMABLE FEATURES Electronic Vehicle Information Center (EVIC) – If Equipped • The EVIC can be used to program the following Personal Settings. Press and release the MENU button until Personal Settings displays, then press the DOWN button to scroll through the settings. Press the SELECT button to change the setting.
ELECTRONICS Sound Horn With Lock • To turn the horn chirp on or off when the doors are locked: • Press the LOCK button for at least 4 seconds, but no longer than 10 seconds. Then, press the PANIC button while still holding the LOCK button. • Release both buttons at the same time. Flashing Lights With Lock • The turn signal lights flashing, when the doors are locked or unlocked, feature can be turned on or off.
ELECTRONICS Programming A Rolling Code System • At the garage door opener motor (in the garage), locate the “learn” or “programming” button. This can usually be found where the hanging antenna wire is attached to the garage door opener motor (it is NOT the button normally used to open and close the door). • Firmly press and release the “learn” or “programming” button. The name and color of the button may vary by manufacturer.
ELECTRONICS NOTE: • Do not exceed the maximum power of 160 Watts (13 Amps) at 12 Volts. If the 160 Watt (13 Amp) power rating is exceeded, the fuse protecting the system will need to be replaced. • Power outlets are designed for accessory plugs only. Do not insert any other object in the power outlet as this will damage the outlet and blow the fuse. Improper use of the power outlet can cause damage not covered by your warranty.
42 Maximum Trailer Weight Ratings Max. GTW (Gross Trailer Wt.) 1,000 lbs (450 kg) 2,000 lbs (900 kg) Max. Trailer Tongue Wt.1 100 lbs (45 kg) 200 lbs (90 kg) Towing a trailer with a larger than recommended frontal area could cause the engine to overheat or cause severe engine damage under extreme conditions. CAUTION! Enclosed trailers or open utility trailers with front shields/guards are not recommended for use with four-cylinder engines with an automatic transmission.
UTILITY RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) Towing This Vehicle Behind Another Vehicle (Flat Towing With All Four Wheels On The Ground) CAUTION! DO NOT flat tow this vehicle. Damage to the drivetrain will result. NOTE: If the vehicle requires towing, make sure all four wheels are off the ground.
WHAT TO DO IN EMERGENCIES 24-HOUR TOWING ASSISTANCE • Dial toll-free 1-800-521-2779 or 1-800-363-4869 for Canadian residents. • Provide your name, vehicle identification number and license plate number. • Provide your location, including telephone number, from which you are calling. • Briefly describe the nature of the problem and answer a few simple questions. • You will be given the name of the service provider and an estimated time of arrival.
WHAT TO DO IN EMERGENCIES • Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is combined with the low tire pressure telltale. When the system detects a malfunction, the telltale will flash for approximately one minute and then remain continuously illuminated. This sequence will continue each time the vehicle is restarted as long as the malfunction exists.
WHAT TO DO IN EMERGENCIES WARNING! Driving a vehicle with the red brake light on is dangerous. Part of the brake system may have failed. It will take longer to stop the vehicle. You could have a collision. Have the vehicle checked immediately. - Malfunction Indicator Light (MIL) • Certain conditions, such as a loose or missing gas cap, poor fuel quality, etc., may illuminate the MIL after engine start. The vehicle should be serviced if the light stays on through several typical driving cycles.
WHAT TO DO IN EMERGENCIES - Transmission Temperature Warning Light • This light indicates that there is excessive transmission fluid temperature that might occur with severe usage such as trailer towing. If this light turns on, stop the vehicle and run the engine at idle, with the transmission in NEUTRAL, until the light turns off. Once the light turns off, you may continue to drive normally.
WHAT TO DO IN EMERGENCIES CAUTION! Driving with a hot cooling system could damage your vehicle. If the temperature gauge reads HOT (H), pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on HOT (H), and you hear continuous chimes, turn the engine off immediately, and call for service. WARNING! You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.
WHAT TO DO IN EMERGENCIES JACKING AND TIRE CHANGING Jack Location • The jack and jack-handle are stowed under the load floor in the trunk. Spare Tire Stowage • The compact spare tire is stowed under the rear load floor in the trunk. • To remove the spare tire, lift up the load floor cover and remove the hold down. Preparations For Jacking • Park on a firm, level surface. Avoid ice or slippery areas. • Set the parking brake and shift the automatic transmission into PARK.
WHAT TO DO IN EMERGENCIES • Block both the front and rear of the wheel diagonally opposite of the jacking position. For example, if changing the right front tire, block the left rear wheel. NOTE: Passengers should not remain in the vehicle when the vehicle is being jacked. Jacking And Tire Changing Instructions • Remove the scissors jack and lug wrench from the spare wheel as an assembly. Turn the jack screw counterclockwise to loosen the lug wrench, and remove the wrench from the jack assembly.
WHAT TO DO IN EMERGENCIES • Place the jack underneath the lift area that is closest to the flat tire. Turn the jack screw clockwise to firmly engage the jack saddle with the lift area of the sill flange. • Raise the vehicle by turning the jack screw clockwise. Raise the vehicle only until the tire just clears the surface and enough clearance is obtained to install the spare tire. • Remove the lug nuts, wheel cover (if equipped) and wheel.
WHAT TO DO IN EMERGENCIES WARNING! (Continued) • Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid being hit when operating the jack or changing the wheel. • Carefully follow these tire changing procedures to help prevent personal injury or damage to your vehicle: Always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle.
WHAT TO DO IN EMERGENCIES Jump-Starting Procedure • Connect the positive (+) end of the jumper cable to the remote positive (+) post of the discharged vehicle. • Connect the opposite end of the positive (+) jumper cable to the positive (+) post of the booster battery. • Connect the negative end (-) of the jumper cable to the negative (-) post of the booster battery. • Connect the opposite end of the negative (-) jumper cable to the remote negative (-) post of the vehicle with the discharged battery.
WHAT TO DO IN EMERGENCIES WARNING! (Continued) • Take care to avoid the radiator cooling fan whenever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan blades. • Remove any metal jewelry, such as watch bands or bracelets, that might make an inadvertent electrical contact. You could be severely injured. • Batteries contain sulfuric acid that can burn your skin or eyes and generate hydrogen gas which is flammable and explosive.
FWD With a Key FWD Without a Key Model Shift lever must be in NEUTRAL. The distance to be traveled must not exceed 15 mi (25 km), and the towing speed must not exceed 25 mph (40 km/h).
WHAT TO DO IN EMERGENCIES FREEING A STUCK VEHICLE • If your vehicle becomes stuck in mud, sand or snow, it can often be moved by a rocking motion. Turn your steering wheel right and left to clear the area around the front wheels. Then move the shift lever back and forth between REVERSE and DRIVE. Using minimal accelerator pedal pressure to maintain the rocking motion, without spinning the wheels, is most effective.
WHAT TO DO IN EMERGENCIES EVENT DATA RECORDER (EDR) • This vehicle is equipped with an event data recorder (EDR). The main purpose of an EDR is to record, in certain crash or near crash-like situations, such as an air bag deployment or hitting a road obstacle, data that will assist in understanding how a vehicle’s systems performed. The EDR is designed to record data related to vehicle dynamics and safety systems for a short period of time, typically 30 seconds or less.
MAINTAINING YOUR VEHICLE OPENING THE HOOD • Pull the release lever located below the instrument panel and in front of the driver’s door. • Raise the hood and locate the safety latch, in the middle of the hood opening. • Move the safety latch while lifting the hood at the same time. • Insert the support rod into the slot on the hood. • To close the hood, remove the support rod and place it in the retaining clip, then lower the hood slowly.
2.
3.
MAINTAINING YOUR VEHICLE FLUIDS AND CAPACITIES Component Engine Coolant 2.4L Fluid, Lubricant, or Genuine Part MOPAR® Antifreeze/Coolant Five Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) or equivalent. Engine Coolant 3.6L MOPAR® Antifreeze/Coolant Five Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) or equivalent. Engine Oil with Filter 2.4L API Certified SAE 5W-20 engine oil, meeting the requirements of Chrysler Material Standard MS-6395.
62 12 18 24 X X X X Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for damage, wear, improper looseness or end play; replace if necessary. Replace the spark plugs (2.4L Engines) X X X X X Replace the engine air cleaner filter. X X Inspect the exhaust system. Replace the air conditioning filter. X X Inspect the CV joints. X X Inspect the brake linings; replace if necessary.
MAINTAINING YOUR VEHICLE Maintenance Record Odometer Date Signature, Authorized Service Center 8,000 Miles (13,000 km) or 6 Months 16,000 Miles (26,000 km) or 12 Months 24,000 Miles (39,000 km) or 18 Months 32,000 Miles (52,000 km) or 24 Months 40,000 Miles (65,000 km) or 30 Months 48,000 Miles (78,000 km) or 36 Months 56,000 Miles (91,000 km) or 42 Months 64,000 Miles (104,000 km) or 48 Months 72,000 Miles (117,000 km) or 54 Months 80,000 Miles (130,000 km) or 60 Months 88,000 Miles (143,000 km) or 66
MAINTAINING YOUR VEHICLE FUSES Integrated Power Module (fuses) • The Integrated Power Module (fuses) is located in the engine compartment near the air cleaner assembly. This center contains cartridge fuses and mini fuses. Cavity 1 2 Mini Fuse 20 Amp Yellow 3 10 Amp Red 4 5 10 Amp Red 20 Amp Yellow 6 10 Amp Red 7 8 30 Amp Green 30 Amp Green 9 40 Amp Green 10 20 Amp Yellow 11 12 13 15 Amp Lt.
MAINTAINING YOUR VEHICLE Cavity Cartridge Fuse 18 40 Amp Green Mini Fuse 19 20 Amp Yellow 20 21 15 Amp Lt. Blue 10 Amp Red 22 10 Amp Red 23 24 15 Amp Lt. Blue 25 Amp Natural 25 10 Amp Red 26 15 Amp Lt.
MAINTAINING YOUR VEHICLE TIRE PRESSURES • Check the inflation pressure of each tire, including the spare tire, at least monthly and inflate to the recommended pressure for your vehicle. • The tire pressures recommended for your vehicle are found on the “Tire and Loading Information” label located on the driver’s side door opening. NOTE: Refer to the Owner's Manual on the DVD for more information regarding tire warnings and instructions. WARNING! • Overloading of your tires is dangerous.
MAINTAINING YOUR VEHICLE EXTERIOR BULBS LIGHT BULBS – Exterior Backup Lamp Rear Tail, Stop, Turn Lamp Center High-Mounted Stop Lamp (CHMSL) Fog Lamp – If Equipped Front Park Lamp Front Turn Signal Lamp Bi-Halogen Headlamp License Lamp Bulb Number 921 LED (Serviced at Authorized Dealer) LED (Serviced at Authorized Dealer) H11 LED (Serviced at Authorized Dealer) 3457AK HR2 W5W 67
CONSUMER ASSISTANCE CHRYSLER GROUP LLC CUSTOMER CENTER P.O. Box 21–8004 Auburn Hills, MI 48321–8004 Phone: 1–800–247–9753 CHRYSLER CANADA INC. CUSTOMER CENTER P.O. Box 1621 Windsor, Ontario N9A 4H6 WARNING! Engine exhaust, some of its constituents, and certain vehicle components contain, or emit, chemicals known to the State of California to cause cancer and birth defects, or other reproductive harm.
CONSUMER ASSISTANCE REPORTING SAFETY DEFECTS IN THE 50 UNITED STATES AND WASHINGTON, D.C. • If you believe that your vehicle has a defect that could cause a collision or cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying the manufacturer. • If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
MOPAR ACCESSORIES AUTHENTIC ACCESSORIES BY MOPAR® • The following highlights just some of the many Authentic Chrysler Accessories by Mopar featuring a fit, finish, and functionality specifically for your Chrysler 200 Convertible. • In choosing Authentic Accessories you gain far more than expressive style, premium protection, or extreme entertainment, you also benefit from enhancing your vehicle with accessories that have been thoroughly tested and factory-approved.
INDEX Airbag . . . . . . . . . . . . . . . . . . 10 Arming Theft System (Security Alarm) . . 9 Automatic Headlights . . . . . . . . . . 17 Automatic Temperature Control (ATC) . 20 Automatic Transmission Fluid Type . . . . . . . . . . . . . . 61 Axle Fluid . . . . . . . . . . . . . . . . 61 Belts, Seat . . . . . . . . . . . . . . . . 9 Brake Fluid . . . . . . . . . . . . . . . 61 Bulb Replacement . . . . . . . . . . . . 67 Calibration, Compass . . . . . . . . . . 37 Change Oil Indicator . . . . . . . . . .
INDEX Preparation for Jacking . . . . . . . . . 49 Programmable Electronic Features . . . 38 Radio Operation . . . . . . . . . . . 26,29 Rain Sensitive Wiper System . . . . . . . 18 Recreational Towing . . . . . . . . . . . 43 Remote Starting System . . . . . . . . . 9 Replacement Bulbs . . . . . . . . . . . 67 Seat Belts . . . . . . . . . . . . . . . . . 9 Seats . . . . . . . . . . . . . . . . . . 13 Adjustment . . . . . . . . . . . . . . 13 Heated . . . . . . . . . . . . . . . . 15 Power . . . . . . . .
The driver’s primary responsibility is the safe operation of the vehicle. Driving while distracted can result in loss of vehicle control, resulting in a collision and personal injury. Chrysler Group LLC strongly recommends that the driver use extreme caution when using any device or feature that may take their attention off the road.
chrysler.com This guide has been prepared to help you get quickly acquainted with your new Chrysler and to provide a convenient reference source for common questions. However, it is not a substitute for your Owner’s Manual. For complete operational instructions, maintenance procedures and important safety messages, please consult your Owner’s Manual, Navigation/ Media Center Manuals, Multimedia User Manual and other Warning Labels in your vehicle.
