2010 OWNER’ S MANUAL Sebring
SECTION TABLE OF CONTENTS PAGE 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 2 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85 3 4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION 1 CONTENTS 䡵 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 Vehicle Identification Number .............. 6 䡵 How To Use This Manual . . . . . . . . . . . . . . . . . . 4 䡵 Vehicle Modifications/Alterations . . . . . . . . . . . . 7 䡵 Warnings And Cautions . . . . . . . . . . . . . . . . . . .
4 INTRODUCTION INTRODUCTION Congratulations on selecting your new Chrysler Group LLC vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. This Owner’s Manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your vehicle.
INTRODUCTION 5 1
6 INTRODUCTION WARNINGS AND CAUTIONS This Owner’s Manual contains WARNINGS against operating procedures that could result in an accident or bodily injury. It also contains CAUTIONS against procedures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important information. Observe all Warnings and Cautions.
INTRODUCTION 7 VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS 䡵 A Word About Your Keys . . . . . . . . . . . . . . . . . 12 䡵 Vehicle Security Alarm — If Equipped . . . . . . . . 18 ▫ Ignition Key Removal . . . . . . . . . . . . . . . . . . 12 ▫ Rearming The System . . . . . . . . . . . . . . . . . . 18 ▫ Key-In-Ignition Reminder . . . . . . . . . . . . . . . 14 ▫ To Arm The System . . . . . . . . . . . . . . . . . . . 18 ▫ Locking The Doors With The Key . . . . . . . . . . 14 ▫ To Disarm The System . . .
10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Remote Open Window Feature — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 24 ▫ Using The Panic Alarm . . . . . . . . . . . . . . . . . 24 ▫ Programming Additional Transmitters . . . . . . 25 ▫ Transmitter Battery Replacement . . . . . . . . . . 25 ▫ General Information . . . . . . . . . . . . . . . . . . . 26 䡵 Remote Start System — If Equipped . . . . . . . . . 26 ▫ How To Use Remote Start . . . . . . . . . . . . . . . 27 䡵 Door Locks . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 ▫ Rear Seat Belts . . . . . . . . . . . . . . . . . . . . . . . 46 ▫ Airbag Deployment Sensors And Controls . . . 60 ▫ Automatic Locking Retractors (ALR) Mode — If Equipped . . . . . . . . . . . . . . . . . . . 46 ▫ Event Data Recorder (EDR) . . . . . . . . . . . . . . 67 ▫ Seat Belt Pretensioners — If Equipped . . . . . . 47 ▫ Supplemental Active Head Restraints (AHR) . . 47 ▫ Enhanced Seat Belt Use Reminder System (BeltAlert威) . . . . . . . . . . . . .
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS The authorized dealer that sold you your vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys from your authorized dealer. Ask your authorized dealer for these numbers and keep them in a safe place. You can insert the double-sided keys into the locks with either side up. Vehicle Key Ignition Key Removal Automatic Transaxle Place the shift lever in PARK.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 occurs, rotate the key to the right slightly, then remove the key as described. If a malfunction occurs, the system will trap the key in the ignition switch lock cylinder to warn you that this safety feature is inoperable. The engine can be started and stopped, but the key cannot be removed until you obtain service.
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE feature is programmable. Refer to “Electronic Vehicle Key-In-Ignition Reminder Information Center (EVIC)/Personal Settings (Cus- Opening the driver’s door when the key is in the ignition, tomer-Programmable Features)” in “Understanding sounds a signal to remind you to remove the key. Your Instrument Panel” for further information. NOTE: • The Key-In-Ignition reminder only sounds when the WARNING! ignition key is placed in the LOCK or ACC position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 SENTRY KEY姞 The Sentry Key威 Immobilizer System prevents unauthorized vehicle operation by disabling the engine. The system does not need to be armed or activated. Operation is automatic, regardless of whether the vehicle is locked or unlocked. seconds for a bulb check. If the light remains on after the bulb check, it indicates that there is a problem with the electronics.
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE All of the keys provided with your vehicle have been authorized dealer or by using the Customer Key Proprogrammed to the vehicle electronics. gramming procedure. This procedure consists of programming a blank key to the vehicle electronics. A blank Replacement Keys key is one which has never been programmed. NOTE: Only keys that have been programmed to the NOTE: When having the Sentry Key威 Immobilizer vehicle electronics can be used to start the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Insert the second valid key into the ignition switch. Turn the ignition switch to the ON position within 15 seconds. After ten seconds, a chime will sound. In addition, the Vehicle Security Light will begin to flash. Turn the ignition switch to the LOCK position and remove the second key. 17 Repeat this procedure to program up to eight keys. If you do not have a programmed Sentry Key威 contact your authorized dealer for details.
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE VEHICLE SECURITY ALARM — IF EQUIPPED To Arm The System The Vehicle Security Alarm monitors the doors and trunk 1. Remove the keys from the ignition switch and get out for unauthorized entry and ignition switch for unauthoof the vehicle. rized operation. 2. Lock the door using either the power door lock switch If something triggers the alarm, the Vehicle Security (one door must be open) or the LOCK button on the Alarm will signal for about 18 minutes.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 NOTE: • The Vehicle Security Alarm remains armed during • During the 16 second arming period, if a door is trunk entry. Pressing the trunk button will not disarm opened or the ignition switch is turned ON, the the Vehicle Security Alarm. If someone enters the Vehicle Security Alarm will automatically disarm. vehicle through the trunk and opens any door, the alarm will sound.
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Tamper Alert If the alarm was triggered, but the warning signals have • The front courtesy overhead console and door courtimed out, the park and taillights flash three times tesy lights do not turn on if the dimmer control is in (instead of the normal twice), and the horn will chirp the interior lights ON position (extreme top position).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 • Inserting the key into the ignition switch disables all To Unlock the Doors Press and release the UNLOCK button on the RKE buttons on the RKE transmitter. transmitter once to unlock the driver’s door, or twice to unlock all doors. The turn signal lights will flash to acknowledge the unlock signal. The Illuminated Entry system (if equipped) will also turn on.
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • For vehicles not equipped with the EVIC, perform the system activated will cause the alarm to sound. Press the following procedure: UNLOCK button to deactivate the Vehicle Security Alarm system. 1. Press and hold the LOCK button on a programmed RKE transmitter for at least four seconds, but not longer Flash Lights With Lock than 10 seconds.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 equipped with EVIC. For details, refer to “Electronic Vehicle Information Center (EVIC)/Personal Settings 3. Test the feature while outside of the vehicle, by (Customer-Programmable Features)” in “Understanding pressing the LOCK/UNLOCK buttons on the RKE transYour Instrument Panel” for further information. mitter with the ignition in the LOCK position, and the To Lock the Doors key removed. Press and release the LOCK button on the RKE transmit4.
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • For vehicles not equipped with the EVIC, perform the To Unlatch the Trunk Press the TRUNK button on the RKE transmitter two following steps: times to unlatch the trunk. 1. Press the LOCK button on a programmed RKE transmitter for at least four seconds, but not longer than Remote Open Window Feature — If Equipped 10 seconds. Then, press the PANIC button while still The RKE remotely lowers both driver and passenger front windows simultaneously.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 headlights and park lights will flash, the horn will pulse NOTE: Perchlorate Material — special handling may on and off, and the Illuminated Entry system (if apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate. equipped) will turn on. 1. With the RKE transmitter buttons facing down, use a The Panic Alarm will stay on for three minutes unless flat blade to pry the two halves of the RKE transmitter you turn it off by pressing the PANIC button a second apart.
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Remove and replace the battery. Avoid touching the If your RKE transmitter fails to operate from a normal new battery with your fingers. Skin oils may cause distance, check for these two conditions. battery deterioration. If you touch a battery, clean it with 1. Weak battery in the RKE transmitter. The expected life rubbing alcohol. of battery is five years. 3. To assemble the RKE transmitter case, snap the two 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE How to Use Remote Start All of the following conditions must be met before the engine will remote start: • Shift lever in PARK • Doors closed • Hood closed • Trunk closed • Hazard switch off • Brake switch inactive (brake pedal not pressed) • Ignition key removed from ignition switch • Battery at an acceptable charge level, and • RKE PANIC button not pressed 27 WARNING! • Do not start or run an engine in a closed garage or confined area.
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: To avoid unintentional shut downs, the system NOTE: • If an engine fault is present the vehicle will start and will disable the one-time press of the Remote Start button for two seconds after receiving a valid remote start then shut down 10 seconds later. request. • For security, power window operation is disabled To Exit Remote Start Mode and Drive the Vehicle when the vehicle is in the Remote Start mode.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE DOOR LOCKS 29 WARNING! Manual Door Locks To lock each door, push the door lock plunger on each door trim panel downward. To unlock each door, pull the door lock plunger on each door trim panel upward. Manual Lock Plunger • For personal security and safety in the event of an accident, lock the vehicle doors as you drive as well as when you park and leave the vehicle.
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CAUTION! An unlocked vehicle is an invitation to thieves. Always remove the key from the ignition and lock all of the doors when leaving the vehicle unattended. Power Door Locks A door lock switch is located on the driver and passenger door panel. Press this switch to lock or unlock the doors. Power Door Lock Switch Auto Door Lock — If Equipped When enabled, your door locks will lock automatically when the vehicle’s speed exceeds 15 mph (24 km/h).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Auto Unlock On Exit The doors will unlock automatically on vehicles with power door locks if: 31 Information Center (EVIC)/Personal Settings (Customer-Programmable Features)” in “Understanding Your Instrument Panel” for further information. 1. The Automatic Unlock Doors on Exit feature is en- • For vehicles not equipped with the EVIC, perform the abled. following procedure: 2. The transmission was in gear and the vehicle speed 1.
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Use the Automatic Unlock Doors on Exit feature The Child Protection Door Locks are located inside the rear edge of the door. Insert the tip of the ignition key or in accordance with local laws. similar flat-bladed object into the lock and rotate approxiChild Protection Door Lock System (Rear Doors) mately one-quarter turn to the lock or unlock position (as To provide a safer environment for children riding in the indicated by the stamped icons).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 WARNING! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged. 2 NOTE: For emergency exit with the system engaged, move the lock plunger up (UNLOCKED position), roll down the window, and open the door with the outside door handle.
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! To cancel the Auto-Down movement, operate the switch either in the up or down direction and release the switch. Never leave children in a vehicle, with the keys in the ignition switch. Occupants, particularly unattended children, can become entrapped by the windows while operating the power window switches. Such entrapment may result in serious injury or death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Auto Window Up — If Equipped Lift the window switch to the second detent, release, and the window will go up automatically. To cancel the Auto Up movement, operate the switch either in the up or down direction and release the switch. 35 WARNING! When the window is almost closed, there is no anti-pinch protection. To avoid personal injury, be sure to clear your arms, hands, fingers and all objects from the window path before closing.
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Window Lockout Switch The window lockout switch on the driver’s door allows you to disable the window control on the other doors. To disable the window controls on the other doors, press the window LOCK button. To enable the window controls, press the window control button again. Window Lockout Switch Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 NOTE: The shift lever must be in PARK for this button TRUNK SAFETY WARNING to operate. To unlatch the trunk lid from outside the vehicle, press and release the TRUNK button on the RKE transmitter two times. With the ignition ON, the word “deck” will display in place of the odometer display indicating that the trunk is open. The odometer display will reappear once the trunk is closed or if the trip button is depressed.
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Trunk Internal Emergency Release As a security measure, a Trunk Internal Emergency Release lever is built into the trunk latching mechanism. In the event of an individual being locked inside the trunk, the trunk can be simply opened by pulling on the glow-in-the-dark handle attached to the trunk latching mechanism. OCCUPANT RESTRAINTS Some of the most important safety features in your vehicle are the restraint systems.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 • An energy-absorbing steering column and steering NOTE: The Advanced Front Airbags have a multistage inflator design. This allows the airbag to have different wheel rates of inflation based on the severity and type of • Knee bolsters/blockers for front seat occupants collision. • Front seat belts incorporate pretensioners to enhance occupant protection by managing occupant energy Please pay close attention to the information in this section.
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Buckle up even though you are an excellent driver, even conditions. However, in a collision the belt will lock and on short trips. Someone on the road may be a poor driver reduce your risk of striking the inside of the vehicle or and cause a collision that includes you. This can happen being thrown out. far away from home or on your own street. Research has shown that seat belts save lives, and they can reduce the seriousness of injuries in a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • Wearing your belt in the wrong place could make your injuries in a collision much worse. You might suffer internal injuries, or you could even slide out of part of the belt. Follow these instructions to wear your seat belt safely and to keep your passengers safe, too. • Two people should never be belted into a single seat belt. People belted together can crash into one another in a collision, hurting one another badly.
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you properly. In a sudden stop, you could move too far forward, increasing the possibility of injury. Wear your seat belt snugly.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A belt that is worn under your arm is dangerous. Your body could strike the inside surfaces of the vehicle in a collision, increasing head and neck injury. A belt worn under the arm can cause internal injuries. Ribs aren’t as strong as shoulder bones. Wear the belt over your shoulder so that your strongest bones will take the force in a collision. • A shoulder belt placed behind you will not protect you from injury during a collision.
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as possible and keep it snug. • A twisted belt can’t do its job properly. In a collision, it could even cut into you. Be sure the belt is straight.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 1. Position the latch plate as close as possible to the anchor point. 2. At about 6 to 12 in (15 to 30 cm) above the latch plate, grasp and twist the belt webbing 180 degrees to create a fold that begins immediately above the latch plate. 2 3. Slide the latch plate upward over the folded webbing. The folded webbing must enter the slot at the top of the latch plate. 4. Continue to slide the latch plate up until it clears the folded webbing.
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Rear Seat Belts The shoulder belt anchorages of the rear three-point belts are nonadjustable for outboard and center rear passengers on sedans. The center belt is mounted to the rear shelf panel and exits through a bezel in the panel. How To Engage The Automatic Locking Mode Automatic Locking Retractors (ALR) Mode — If Equipped In this mode, the shoulder belt is automatically prelocked. The belt will still retract to remove any slack in the shoulder belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seat Belt Pretensioners — If Equipped The seat belts for both front seating positions may be equipped with pretensioning devices that are designed to remove slack from the seat belt in the event of a collision. These devices improve the performance of the seat belt by assuring that the belt is tight about the occupant early in a collision. Pretensioners work for all size occupants, including those in child restraints.
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE However if during a front impact, a secondary rear impact occurs, the AHR may deploy based on the severity and type of the impact. CAUTION! All occupants, including the driver, should not operate a vehicle or sit in a vehicle’s seat until the head restraints are placed in their proper positions in order to minimize the risk of neck injury in the event of a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 1. Grasp the deployed AHR from the rear seat. 49 3. Pull down then rearward towards the rear of the vehicle then down to engage the locking mechanism. 2 Hand Positioning Points On AHR 2. Position the hands on the top of the deployed AHR at a comfortable position.
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3 — Final Downward Movement To Engage Locking Mechanism AHR In Reset Position NOTE: 4. The AHR front soft foam and trim half should lock • If you have difficulties or problems resetting the Active Head Restraints, see an authorized dealer. into the back decorative plastic half. • For safety reasons, have the Active Head Restraints checked by a qualified specialist at an authorized dealer.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Enhanced Seat Belt Use Reminder System (BeltAlert姞) If the driver’s seat belt has not been buckled within 60 seconds of starting the vehicle and if the vehicle speed is greater than 5 mph (8 km/h), the BeltAlert威 will alert the driver to buckle the seat belt. The driver should also instruct all other occupants to buckle their seat belts.
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Watch for the Seat Belt Reminder Light to turn on while unbuckling and off while re-buckling the seat belt. It may be necessary to retract the seat belt partially each time when unbuckling. Pregnant women should wear the lap part of the belt across the thighs and as snug across the hips as possible. Keep the belt low so that it does not come across the abdomen. That way the strong bones of the hips will take the force if there is a collision. 4.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 WARNING! Using a seat belt extender when not needed can increase the risk of injury in a collision. Only use when the lap belt is not long enough when it is worn low and snug, and in the recommended seating positions. Remove and store the extender when not needed.
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The Advanced Front Airbags have a multistage inflator NOTE: design. This allows the airbag to have different rates of • Airbag covers may not be obvious in the interior trim; but they will open during airbag deployment. inflation that are based on the severity and type of collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 • Supplemental Seat-Mounted Side Airbags (SAB) the second stage determines whether the output force is low, medium, or high. If a low output is sufficient to meet • Supplemental Side Airbag Inflatable Curtains (SABIC) the need, the remaining gas in the inflator is expended.
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • Do not drill, cut or tamper with the knee bolster in any way. • Do not mount any accessories to the knee bolster such as alarm lights, stereos, citizen band radios, etc. Supplemental Seat-Mounted Side Airbags (SAB) — If Equipped Supplemental Seat-Mounted Side Airbags provide enhanced protection to help protect an occupant during a side impact.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 Supplemental Side Airbag Inflatable Curtain (SABIC) — If Equipped SABIC airbags may offer side-impact and vehicle rollover protection to front and rear seat outboard occupants in addition to that provided by the body structure. Each airbag features inflated chambers placed adjacent to the head of each outboard occupant that reduce the potential for side-impact head injuries. The SABIC airbags deploy downward, covering both windows on the impact side.
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The system includes side impact sensors adjacent to both front and rear seat occupants that are calibrated to deploy the SABIC airbags during impacts that require airbag occupant protection. WARNING! • If your vehicle is equipped with left and right Supplemental Side Airbag Inflatable Curtain (SABIC), do not stack luggage or other cargo up high enough to block the location of the SABIC.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Infants in rear facing child restraints should NEVER ride in the front seat of a vehicle with a passenger Advanced Front Airbag. An airbag deployment can cause severe injury or death to infants in that position. Children that are not big enough to wear the vehicle seat belt properly (see section on Child Restraints) should be secured in the rear seat in child restraints or beltpositioning booster seats.
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 5. If the airbag system in this vehicle needs to be modified to accommodate a disabled person, contact the Customer Center. Phone numbers are provided under ⴖIf You Need Assistanceⴖ. WARNING! • Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly. In some collisions, the airbags won’t deploy at all. Always wear your seat belts even though you have airbags.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Advanced Front Airbags are designed to provide additional protection by supplementing the seat belts in certain frontal collisions depending on the severity and type of collision. Advanced Front Airbags are not expected to reduce the risk of injury in rear, side, or rollover collisions.
62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Also, the ORC turns on the Airbag Warning Light in the instrument panel for approximately six to eight seconds for a self-check when the ignition is first turned on. After the self-check, the Airbag Warning Light will turn off. If the ORC detects a malfunction in any part of the system, it turns on the Airbag Warning Light, either momentarily or continuously. A single chime will sound if the light comes on again after initial startup.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 triggered, releasing a quantity of non-toxic gas. The inflating side airbag exits through the seat seam into the space between the occupant and the door. The side airbags fully inflate in about 10 milliseconds.
64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE covers the window. The airbag inflates in about 30 ms (about one-quarter of the time that it takes to blink your eyes) with enough force to injure you if you are not belted and seated properly, or if items are positioned in the area where the side curtain airbag inflates. This especially applies to children. The side curtain airbag is only about 3-1/2 in (9 cm) thick when it is inflated.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Front and/or side airbags will not deploy in all collisions. This does not mean something is wrong with the airbag system. If you do have a collision, which deploys the airbags, any or all of the following may occur: 65 airbag inflation. These airborne particles may irritate the skin, eyes, nose, or throat. If you have skin or eye irritation, rinse the area with cool water. For nose or throat irritation, move to fresh air.
66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Maintaining Your Airbag System WARNING! (Continued) WARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. You could be injured if the airbag system is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the steering wheel hub trim cover or the upper right side of the instrument panel.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag Warning Light You will want to have the airbags ready to inflate for your protection in a collision. While the airbag system is designed to be maintenance free, if any of the following occurs, have an authorized dealer service the system immediately. • The Airbag Warning Light does not come on during the six to eight seconds when the ignition switch is first turned on. • The Airbag Warning Light remains on after the six to eight second interval.
68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Under certain circumstances, EDR data may not be accessing the electronic data stored, unless ordered to image the data by a court with legal jurisdiction (i.e., recorded (e.g., loss of battery power). pursuant to a warrant). A copy of the data will be In conjunction with other data gathered during a comprovided to the custodial entity upon request.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 United States and all Canadian provinces require that small children ride in proper restraint systems. This is the law, and you can be prosecuted for ignoring it. 3. Requested by police under a legal warrant. 4. Otherwise required by law. Data parameters that are recorded: Children 12 years and younger should ride properly • Diagnostic trouble code(s) and warning light status for buckled up in a rear seat, if available.
70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE There are different sizes and types of restraints for • The infant carrier is only used rearward-facing in the children from newborn size to the child almost large vehicle. It is recommended for children who weigh up enough for an adult safety belt. Always check the child to about 20 lbs (9 kg). Convertible child seats can be seat owner’s manual to ensure you have the correct seat used either rearward-facing or forward-facing in the for your child.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Older Children and Child Restraints Children who weigh more than 20 lbs (9 kg) and who are older than one year can ride forward-facing in the vehicle. Forward-facing child seats and convertible child seats used in the forward-facing direction are for children who weigh 20 to 40 lbs (9 to 18 kg) and who are older than one year. These child seats are also held in the vehicle by the lap/shoulder belt or the LATCH child restraint anchorage system.
72 • • • • THINGS TO KNOW BEFORE STARTING YOUR VEHICLE bend over the front of the seat when their back is • In the rear seat, you may have trouble tightening the against the seatback, should use the lap/shoulder belt lap/shoulder belt on the child restraint because the in a rear seat. buckle or latch plate is too close to the belt path opening on the restraint.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 lower anchorages that are capable of accommodating LATCH-compatible child seats having flexible, webbingWhen your child restraint is not in use, secure it in mounted lower attachments. Child seats with fixed lower the vehicle with the seat belt or remove it from the attachments must be installed in the outboard positions only. Regardless of the specific type of lower attachment, vehicle. Don’t leave it loose in the vehicle.
74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE to the top tether anchorage, have been available for some time. In fact, many child restraint manufacturers will provide add-on tether strap kits for some of their older products. Tether anchorage kits are also available for most older vehicles.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Remind all children in the vehicle that the seat belts are not toys and should not be played with, and never leave your child unattended in the vehicle. Installing the LATCH-Compatible Child Restraint System We urge you to carefully follow the directions of the manufacturer when installing your child restraint. Not all child restraint systems will be installed as described here.
76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE cover directly behind the seat where you are placing the child restraint and attach the tether strap to the anchorage, being careful to route the tether strap to provide the most direct path between the anchor and the child restraint. Finally, tighten all three straps as you push the child restraint rearward and downward into the seat, removing slack in the straps according to the child restraint manufacturer’s instructions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77 2. Route the tether strap to provide the most direct path for the strap between the anchor and the child seat. If 1. Rotate the cover over the anchor directly behind the your vehicle is equipped with adjustable rear head seat where you are placing the child restraint. restraints, raise the head restraint, and where possible, route the tether strap under the head restraint and between the two posts.
78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE In the rear seat, you may have trouble tightening the lap/shoulder belt on the child restraint because the buckle or latch plate is too close to the belt path opening on the restraint. Disconnect the latch plate from the buckle and twist the short buckle-end belt several times to shorten it. Insert the latch plate into the buckle with the The seat belt must be in the Automatic Locking Mode in release button facing out.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Children Too Large for Booster Seats Children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the seatback, should use the lap/shoulder belt in a rear seat. Make sure that: • The child is upright in the seat. 79 Transporting Pets Airbags deploying in the front seat could harm your pet.
80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant. Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur. For the recommended viscosity and quality grades refer to “Maintenance Procedures” in “Maintaining Your Vehicle”. NON-DETERGENT OR STRAIGHT MINERAL OILS MUST NEVER BE USED.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Exhaust Gas WARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (CO) follow these safety tips: Do not run the engine in a closed garage or in confined areas any longer than needed to move your vehicle in or out of the area.
82 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Defroster Check operation by selecting the defrost mode and place the blower control on high speed. You should be able to Seat Belts feel the air directed against the windshield. See your Inspect the belt system periodically, checking for cuts, authorized dealer for service if your defroster is frays, and loose parts. Damaged parts must be replaced inoperable. immediately. Do not disassemble or modify the system.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 83 WARNING! WARNING! (Continued) Pedals that cannot move freely can cause loss of vehicle control and increase the risk of serious personal injury. • Always make sure that floor mats are properly attached to the floor mat fasteners. • Never place or install floor mats or other floor coverings in the vehicle that cannot be properly secured to prevent them from moving and interfering with the pedals or the ability to control the vehicle.
84 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Periodic Safety Checks You Should Make Outside the Vehicle Door Latches Check for positive closing, latching, and locking. Tires Examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread. Inspect the tread and sidewall for cuts and cracks. Check the wheel nuts for tightness. Check the tires (including spare) for proper pressure.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 䡵 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 䡵 Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93 ▫ Inside Day/Night Mirror . . . . . . . . . . . . . . . . 89 ▫ Manual Front Seat Adjustment . . . . . . . . . . . . 94 ▫ Automatic Dimming Mirror — If Equipped . . . 90 ▫ Driver Seat Manual Height Adjuster — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 94 ▫ Power Mirrors . . . . . . . . . . .
86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Fold-Flat Passenger Seatback . . . . . . . . . . . . 102 ▫ Fog Lights — If Equipped . . . . . . . . . . . . . . 109 ▫ Folding Rear Seat . . . . . . . . . . . . . . . . . . . . 102 ▫ Daytime Running Lights — If Equipped . . . . 109 ▫ Folding Rear Seat Center Armrest . . . . . . . . 103 ▫ Lights On Reminder . . . . . . . . . . . . . . . . . . 110 䡵 To Open And Close The Hood . . . . . . . . . . . . 104 ▫ Instrument Panel Dimmer . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 䡵 Electronic Speed Control . . . . . . . . . . . . . . . . 117 䡵 Power Sunroof — If Equipped . . . . . . . . . . . . 126 ▫ To Activate . . . . . . . . . . . . . . . . . . . . . . . . . 117 ▫ Sunroof Operation . . . . . . . . . . . . . . . . . . . 127 ▫ To Set a Desired Speed . . . . . . . . . . . . . . . . 118 ▫ Auto Sunroof Express With Anti-Pinch Protection — If Equipped . . . . . . . . . . . . . . 128 ▫ To Deactivate . . . . . . . . . . . . . . . . .
88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 䡵 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133 䡵 Console Features . . . . . . . . . . . . . . . . . . . . . . 135 ▫ Driver’s Side Sunglass Holder — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . 133 ▫ Dual Storage Bins . . . . . . . . . . . . . . . . . . . . 135 ▫ Cargo Area . . . . . . . . . . . . . . . . . . . . . . . . 134 ▫ Video Console — If Equipped . . . . . . . . . . . 137 䡵 Rear Window Features . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 MIRRORS Inside Day/Night Mirror A two-point pivot system allows for horizontal and vertical mirror adjustment. Adjust the mirror to center on the view through the rear window. 3 Headlight glare can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle). The mirror should be adjusted while set in the day position (toward the windshield).
90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Dimming Mirror — If Equipped This mirror will automatically adjust for headlight glare from vehicles behind you. Push in the button on the face of the mirror to activate the dimming feature. CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91 3 Power Mirror Switch Mirror Directions After selecting a mirror, move the knob in the same Adjusting Sideview Mirrors direction you want the mirror to move. When finished, Outside Mirror — Driver Side return the knob to the center (Off) position to guard Adjust the outside mirror to center on the adjacent lane of against accidentally moving a mirror position. traffic, with a slight overlap of the view obtained on the inside mirror.
92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Outside Mirror — Passenger Side Adjust the convex outside mirror so you can just see the side of your vehicle in the part of the mirror closest to the vehicle. Illuminated Vanity Mirrors — If Equipped An illuminated vanity mirror is on each sun visor. To use the mirror, lower the sun visor and rotate the mirror cover upward. The lights will turn on automatically. Closing the mirror cover turns off the lights.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Uconnect™ Phone — IF EQUIPPED Uconnect™ Phone is a hands-free system that allows you to use voice commands to dial a phone number stored in your cellular phone. Press the Uconnect™ Phone on the radio or steering wheel controls (if button equipped) and follow the instructions to pair the cellular phone. Refer to “Uconnect™ Phone” in the Uconnect™ User Manual located on the DVD for further details.
94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Manual Front Seat Adjustment The manual seat adjustment bar is at the front of the seat, near the floor. Pull the bar upward to move the seat forward or rearward. Release the bar once the seat is in the position desired. Then, using body pressure, move forward and rearward on the seat to be sure that the seat adjusters have latched. WARNING! Adjusting a seat while the vehicle is moving is dangerous.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 3 Manual Seat Height Adjustment Lever Reclining Bucket Seats The recliner control is on the side of the seat. To recline, lean forward slightly before lifting the lever, then lean back to the desired position and release the lever. Lean forward and lift the lever to return the seatback to its normal position.
96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust the seat only while the vehicle is parked. • Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or even fatally injured.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Seats — If Equipped The power seat switches are on the outboard side of the seat near the floor. Use the bottom switch to move the seat up, down, forward, rearward, or to tilt the seat. The top switch controls the seatback recliner. 97 WARNING! • Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured.
98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Adjusting Active Head Restraints Active Head Restraints can reduce the risk of injury in the event of a rear impact. The Active Head Restraint should be adjusted so the top of the head restraint is located above the top of your ear. To raise the head restraint, pull upward on the head restraint (on some models, you may need to press the push button).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99 For comfort the Active Head Restraints can be tilted forward and backward. To tilt the head restraint closer to the back of your head, pull outward on the bottom of the head restraint. Push rearward on the bottom of the head restraint to move the head restraint away from your head. 3 Active Head Restraint (Tilted) NOTE: • The head restraints should only be removed by qualified technicians, for service purposes only.
100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • In the event of deployment of an Active Head Restraint, refer to “Occupant Restraints/Resetting Active Head Restraints (AHR)” in “Things to Know Before Starting Your Vehicle” for further information. WARNING! • Driving a vehicle with the head restraints removed or improperly adjusted could cause serious injury or death in the event of a collision.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Heated Seats — If Equipped This feature heats leather or cloth front driver and passenger seats. The switches for the heated seats are located in the center console above the climate controls. After turning the ignition ON, you can choose from High, Low, or Off heat settings. Amber indicator lights in each switch indicate the level of heat in use. Two indicator lights will illuminate for High, one for Low and none for Off.
102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Fold-Flat Passenger Seatback The recline handle on the front passenger seat also releases the seatback to fold forward. Fold-Flat Front Passenger Seat Folding Rear Seat To provide additional storage area, the rear seatback can Seatback Adjustment be folded forward. Pull on the loops shown in the picture The hard seatback features a work surface and a molded to fold down either or both seatbacks. rim for retaining items stored on the seatback panel.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 Folding Rear Seat Center Armrest The rear seat is equipped with a folding armrest with cupholders. 3 Folding Rear Seats WARNING! The rear cargo area of the vehicle (with the rear seatbacks in the locked-up or folded down position) should not be used as a play area by children. They could be seriously injured in an accident. Children should be seated and using the proper restraint system.
104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE TO OPEN AND CLOSE THE HOOD To open the hood, two latches must be released. 1. Pull the hood release lever located under the left side of the instrument panel. Hood Safety Catch Use the hood prop rod to secure the hood in the open position. Place the upper end of the prop rod in the hole on the left underside of the hood. Hood Release Lever 2. Then lift the secondary latch located under the front edge of the hood, near the center and raise the hood.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 CAUTION! To prevent possible damage, do not slam the hood to close it. Use a firm downward push at the center of the hood to ensure that both latches engage. 3 WARNING! Hood Prop Rod Hole Location Be sure the hood is fully latched before driving your vehicle. If the hood is not fully latched, it could open when the vehicle is in motion and block your vision. Failure to follow this warning could result in serious injury or death.
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE passing light, fog lights, instrument panel light dimming Headlights and Parking Lights and turn signals. The multifunction lever is located on Turn the end of the multifunction lever to the first detent for parking light operation. Turn to the second detent for the left side of the steering column. headlight operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 With the engine running and the multifunction lever in Automatic Headlights — If Equipped Turning the end of the multifunction lever to the third the AUTO position, the headlights will turn on and turn detent (AUTO), will activate the automatic headlight off based on the surrounding light levels. system. Headlight Time Delay There is also a feature that delays turning off the vehicle lights for 30, 60 or 90 seconds after the ignition switch is turned OFF.
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Turn Signals Move the multifunction lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights. NOTE: If either light remains on and does not flash, or there is a very fast flash rate, check for a defective outside light bulb. If an indicator fails to light when the lever is moved, it would suggest that the indicator bulb is defective.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 NOTE: If the multifunction lever is held in the flash-topass position for more than 15 seconds, the high beams will shut off. If this occurs, wait 30 seconds for the next flash-to-pass operation. Fog Lights — If Equipped The front fog light switch is on the multifunction lever. To activate the front fog lights, turn on the parking lights or the low beam headlights and pull out the end of the multifunction lever.
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE whenever the ignition is ON, the engine is running, the Rotate the center portion of the lever upward to the next headlight switch is off, the parking brake is released and detent position to brighten the odometer and radio when the parking lights or headlights are on. the shift lever is in any position except PARK.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 Map/Reading/Interior Lights These lights are mounted between the sun visors above the rearview mirror. Each light can be turned on by pressing the barrel. Press the barrel a second time to turn the light off. Both of these lights can swivel so that the light can be aimed at a specific spot, if desired. The lights will remain on until the switch is pressed a second time, so be sure they have been turned off before leaving the vehicle.
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE is open. To restore interior light operation, either turn the Rotate the end of the lever to the LO position for low-speed wiper operation, or to the HI position for ignition switch ON or cycle the light switch. high-speed wiper operation. WINDSHIELD WIPERS AND WASHERS The wipers and washers are operated by a switch on the control lever. The lever is located on the right side of the steering column.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 are operating. The wipers will resume operation when then turn the end of the lever to select the desired delay you turn the ignition switch to the ON position again. interval. There are five delay settings, which allow you to regulate the wipe interval from a minimum of one cycle CAUTION! every second to a maximum of approximately 18 seconds between cycles. • Turn the windshield wipers off when driving through an automatic car wash.
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The wiper delay times depend on vehicle speed. If the vehicle is moving less than 10 mph (16 km/h), delay times will be doubled. Windshield Washers To use the washer, pull the windshield wiper/washer control lever toward you and hold it for as long as washer spray is desired. WARNING! Sudden loss of visibility through the windshield could lead to an accident. You might not see other vehicles or other obstacles.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 Headlights With Wipers Feature (Available With Automatic Headlights Only) When this feature is active, the headlights will turn on approximately 10 seconds after the wipers are turned on if the multifunction lever (on the left side of the steering column) is placed in the AUTO position. In addition, the headlights will turn off when the wipers are turned off if they were turned on by this feature.
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE TILT/TELESCOPING STEERING COLUMN This feature allows you to tilt the steering column upward or downward. It also allows you to lengthen or shorten the steering column. The tilt/telescoping control handle is located below the steering wheel at the end of the steering column. To unlock the steering column, pull the control handle outward. To tilt the steering column, move the steering wheel upward or downward as desired.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 NOTE: In order to ensure proper operation, the Electronic Speed Control System has been designed to shut down if multiple Speed Control functions are operated at the same time. If this occurs, the Electronic Speed Control System can be reactivated by pushing the Electronic The Electronic Speed Control lever is located on the right Speed Control ON/OFF button and resetting the desired side of the steering wheel. vehicle set speed.
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Leaving the Electronic Speed Control on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the system off when you are not using it. To Set a Desired Speed Turn the Electronic Speed Control ON. When the vehicle reaches the speed desired, press down on the lever and release SET DECEL.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ACCEL lever. If the lever is continually held in the RESUME ACCEL position, the set speed will continue to increase until the lever is released, then the new set speed will be established. Tapping RESUME ACCEL once will result in a 1 mph (2 km/h) speed increase. Each time the lever is tapped, speed increases so that tapping the lever three times will increase speed by 3 mph (5 km/h), etc.
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE On steep hills, a greater speed loss or gain may occur so The HomeLink威 buttons that are located in the headliner it may be preferable to drive without Electronic Speed or sun visor designate the three different HomeLink威 Control. channels. WARNING! Electronic Speed Control can be dangerous where the system cannot maintain a constant speed. Your vehicle could go too fast for the conditions, and you could lose control. An accident could be the result.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Your motorized door or gate will open and close while you are training the universal transceiver. Do not train the transceiver if people, pets or other objects are in the path of the door or gate. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by Federal safety standards. This includes most garage door opener models manufactured after 1982.
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Place the handheld transmitter 1 to 3 in (3 to 8 cm) away • After training a HomeLink威 channel, if the garage from the HomeLink威 button you wish to program while door does not operate with HomeLink威 and the gakeeping the indicator light in view. rage door opener was manufactured after 1995, the garage door opener may have a rolling code. If so, 3.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 This can usually be found where the hanging antenna 6. Firmly press and release the LEARN or TRAINING wire is attached to the garage door opener motor. It is button. The name and color of the button may vary by NOT the button normally used to open and close the manufacturer. door. NOTE: You have 30 seconds in which to initiate the next step after the LEARN button has been pressed. 7.
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Using HomeLink威 To operate, press and release the programmed HomeLink威 button. Activation will now occur for the trained device (i.e., garage door opener, gate operator, security system, entry door lock, home/office lighting, etc.,). The handheld transmitter of the device may also be used at any time.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 successfully accepted the frequency signal. The indica- Troubleshooting Tips tor light will flash slowly and then rapidly when fully If you are having trouble programming HomeLink威, here are some of the most common solutions: trained. If you unplugged the device for training, plug it back in • Replace the battery in the original transmitter. at this time. • Press the LEARN button on the Garage Door Opener to complete the training for a Rolling Code.
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE General Information POWER SUNROOF — IF EQUIPPED This device complies with FCC rules Part 15 and Industry The sunroof controls are mounted between the dome/ Canada RSS-210. Operation is subject to the following reading lights. two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference that may be received including interference that may cause undesired operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Never leave children in a vehicle with the key in the ignition switch. Occupants, particularly unattended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death. • In an accident, there is greater risk of being thrown from a vehicle with an open sunroof. You could also be seriously injured or killed.
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The sunshade cannot be closed if the sunroof is Venting Sunroof — Express Press and release the “Vent” button, the sunroof will open. open to the vent position. This is called “Express Vent”. Wind Buffeting Closing Sunroof — Express Wind buffeting can be described as the perception of Press the switch forward and release, the sunroof will pressure on the ears or a helicopter-type sound in the close automatically from any position. The sunroof will ears.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Ignition Off Operation For vehicles not equipped with the Electronic Vehicle Information Center (EVIC), the power sunroof switch will remain active for 45 seconds after the ignition switch is turned OFF. Opening either front door will cancel this feature. The instrument panel power outlet, located below the climate control knobs, has power available only when the ignition is ON. This power outlet will also operate a conventional cigar lighter unit.
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE There is a power outlet located on the inside of the center NOTE: console. This power outlet is powered directly from the • To ensure proper operation a MOPAR威 knob and element must be used. battery (power available at all times). Items plugged into this power outlet may discharge the battery and/or • Do not exceed the maximum power of 160 Watts (13 prevent the engine from starting. Amps) at 12 Volts.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting. • Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.) will degrade the battery even more quickly.
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! For vehicles equipped with the heated and cooled cupholder, locate the cup holder ash receiver in the forward cupholder. The optional ash receiver also comes with a cigar lighter. You may use the power outlet, located in the instrument panel below the climate control knobs, or in the bottom of the console compartment, for this cigar lighter.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 STORAGE Driver’s Side Sunglass Holder — If Equipped An integrated sunglass holder is located in the headliner above the sun visor. To access the sunglass holder, lower the sun visor. Small items such as toll tickets can be stored between the two straps, while sunglasses or other items can be stored above the two straps.
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Cargo Area The 60/40 split-folding rear seat provides cargo-carrying versatility. The seatbacks fold down easily by pulling nylon tabs between the seatbacks and the bolsters. When the seats are folded down, they provide a continuous, nearly flat extension of the load floor. When the seatback is folded to the upright position, make sure it is latched by strongly pulling on the top of the seatback above the seat strap.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 Always place cargo evenly on the cargo floor. Put heavier objects as low and as far forward as possible. Place as much cargo as possible in front of the rear axle. Too much weight or improperly placed weight over or behind the rear axle can cause the rear of the vehicle to sway. Do not pile luggage or cargo higher than the top of the seatback. This could impair visibility or become a dangerous projectile in a sudden stop or collision.
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The lower bin can be accessed directly, without first exposing the upper bin, by operating the right latch with the armrest down. The first storage bin can be used to hold smaller items. The lower storage bin includes a molded-in coin holder, room for CD’s, DVD’s, and a power outlet that allows a cellular phone to recharge while concealed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 Video Console — If Equipped The optional Video Entertainment System (VES)™ includes the following components: • The screen for a rear seat DVD player is stored under the armrest. 3 • Remote Control • Audio/Video RCA Jacks Video Console Refer to “Video Entertainment System — If Equipped,” in “Understanding Your Instrument Panel” for further information.
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE REAR WINDOW FEATURES Rear Window Defroster The rear window defroster button is located on the climate control (Mode) knob. Press this button to turn on the rear window defroster and the heated outside mirrors (if equipped). An indicator in the button will illuminate when the rear window defroster is on. The rear window defroster automatically turns off after approximately 10 minutes. For an additional five minutes of operation, press the button a second time.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 Instrument Panel Features . . . . . . . . . . . . . . . 143 䡵 Instrument Cluster . . . . . . . . . . . . . . . . . . . . 144 䡵 Instrument Cluster Descriptions . . . . . . . . . . . 145 䡵 Electronic Vehicle Information Center (EVIC) – If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 158 ▫ Electronic Vehicle Information Center (EVIC) Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . 160 ▫ Oil Change Required — If Equipped . . . . . .
140 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ List Button (Disc Mode For MP3/WMA Play) . . . . . . . . . 182 䡵 Media Center 130 (RES) — AM/FM Stereo Radio With CD Player (MP3 AUX Jack). . . . . . . 189 ▫ Info Button (Disc Mode For MP3/WMA Play) . . . . . . . . . 183 ▫ Operating Instructions — Radio Mode . . . . . 190 䡵 Media Center 730N/430 (RER/REN/RBZ) — AM/FM Stereo Radio And CD/DVD/HDD/ NAV — If Equipped . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Info Button (CD Mode For MP3 Play) . . . . . . 209 ▫ Operating Instructions - Uconnect™ Phone (If Equipped) . . . . . . . . . . . . . . . . . . . . . . . 210 䡵 Uconnect™ Multimedia (Satellite Radio) — If Equipped (REN/REQ/RER/RBZ/RES Radios Only) . . . . . . . . . . . . . . . . . . . . . . . . . 210 ▫ System Activation . . . . . . . . . . . . . . . . . . . . 211 ▫ Electronic Serial Number/Sirius Identification Number (ESN/SID) . . . . . . . . .
142 UNDERSTANDING YOUR INSTRUMENT PANEL 䡵 CD/DVD Disc Maintenance . . . . . . . . . . . . . . 218 䡵 Radio Operation And Cellular Phones . . . . . . . 219 䡵 Climate Controls . . . . . . . . . . . . . . . . . . . . . . 219 ▫ Manual Heating And Air Conditioning . . . . . 219 ▫ Automatic Temperature Control (ATC) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . 223 ▫ Operating Tips . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 143 INSTRUMENT PANEL FEATURES 4 1 2 3 4 5 — Air Outlet — Side Window Demister Outlet — Instrument Cluster — Ignition Switch — Analog Clock 6 — Radio 7 — Passenger Airbag 8 — Glove Compartment 9 — Heated Seat Switch – If Equipped 10 — Hazard Switch 11 — Storage Compartment 12 — Climate Control 13 — Trunk Release Button
144 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER
UNDERSTANDING YOUR INSTRUMENT PANEL 145 removes this heat. You can also turn the Temperature control to maximum heat, the Mode control to Floor and 1. Temperature Gauge the Fan control to High. This allows the heater core to act The temperature gauge shows engine coolant temperaas a supplement to the radiator and aids in removing heat ture. Any reading below the red area of the gauge shows from the engine cooling system. that the engine cooling system is operating properly.
146 UNDERSTANDING YOUR INSTRUMENT PANEL If jump starting is required, refer to “Jump Starting 5. Low Fuel Light When the fuel level drops to approximately 2.0 gal- Procedures” in “What To Do In Emergencies”. lons (7.6 Liters), the fuel symbol will light and a 7. Airbag Warning Light single chime will sound. The light comes on and remains on for six to NOTE: This light will remain on until a minimum of eight seconds as a bulb check when the ignition switch is first turned ON.
UNDERSTANDING YOUR INSTRUMENT PANEL 147 you do not buckle up, the light will remain on. Refer to 10. Engine Temperature Warning Light “Occupant Restraints” in “Things To Know Before StartThis light warns of an overheated engine condition. If the engine is critically hot, a warning chime ing Your Vehicle” for further information. will sound 10 times. After the chime turns off, the 9. Oil Pressure Warning Light engine will still be critically hot until the light goes out.
148 UNDERSTANDING YOUR INSTRUMENT PANEL The light will remain on until the cause is corrected. In the event of an EBD failure, the Brake Warning Light will turn on along with the ABS Light. Immediate repair NOTE: The light may flash momentarily during sharp to the ABS system is required. cornering maneuvers which change fluid level conditions. The vehicle should have service performed, and The operation of the Brake Warning Light can be checked the brake fluid level checked.
UNDERSTANDING YOUR INSTRUMENT PANEL 149 driven. If your odometer needs to be repaired or serviced, the repair technician should leave the odometer reading the same as it was before the repair or service. If s/he cannot do so, then the odometer must be set at zero, and a sticker must be placed in the door jamb stating what the mileage was before the repair or service. It is a good idea 13.
150 UNDERSTANDING YOUR INSTRUMENT PANEL Vehicle Odometer Messages LoW TirE When the appropriate conditions exist, the odometer will When the appropriate condition exists, the odometer display the following messages: display will toggle between LoW and TirE for three cycles. door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Door Ajar HOTOIL deck . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Trunk Ajar When this message is displayed there is a transmission LoW TirE . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL tighten the fuel filler cap properly and press the odometer reset button to turn off the “gASCAP” message. (Refer to “Onboard Diagnostic System — OBDII” in “Maintaining Your Vehicle” for further information). If the problem continues, the message will appear the next time the vehicle is started. See your authorized dealer service center as soon as possible. 151 To turn off the message temporarily, press and release the Trip Odometer button on the instrument cluster.
152 UNDERSTANDING YOUR INSTRUMENT PANEL Dual Trip Odometer — If Equipped 15. Cruise Indicator — If Equipped This indicator shows that the Electronic Speed Press and release this button to change the display from odometer to “Trip A.” Press and release it a second time Control System is ON. to change the display to “Trip B.” Press and release it a 16. Odometer/Trip Odometer Reset Button third time to change the display back to the odometer.
UNDERSTANDING YOUR INSTRUMENT PANEL 153 If the light is flashing when the engine is running you 19. Electronic Stability Control (ESC) OFF Indicator may experience power loss, an elevated/rough idle, and Light — If Equipped increased brake pedal effort, and your vehicle may This light indicates the Electronic Stability Conrequire towing. Immediate service is required. trol system (ESC) has been turned off by the driver.
154 UNDERSTANDING YOUR INSTRUMENT PANEL 23. Anti-Lock Brake (ABS) Light — If Equipped This light monitors the ABS. This light will come on when the ignition key is turned to the ON position and may stay on for approximately three seconds.
UNDERSTANDING YOUR INSTRUMENT PANEL 155 Activation/Malfunction Indicator Light” come on mo- As an added safety feature, your vehicle has been mentarily each time the ignition switch is turned ON. equipped with a Tire Pressure Monitoring System (TPMS) that illuminates a low tire pressure telltale when • Each time the ignition is turned ON, the ESC system one or more of your tires is significantly under-inflated. will be ON even if it was turned off previously.
156 UNDERSTANDING YOUR INSTRUMENT PANEL Your vehicle has also been equipped with a TPMS CAUTION! malfunction indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is The TPMS has been optimized for the original combined with the low tire pressure telltale. When the equipment tires and wheels.
UNDERSTANDING YOUR INSTRUMENT PANEL 157 bulb does not come on when turning the key from LOCK to ON, have the condition checked promptly. WARNING! Certain conditions such as a loose or missing gas cap, poor fuel quality, etc., may illuminate the light after engine start. The vehicle should be serviced if the light stays on through several of your typical driving cycles. In most situations, the vehicle will drive normally and will not require towing.
158 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! Continuous driving with the Transmission Temperature Warning Light illuminated will eventually cause severe transmission damage or transmission failure. WARNING! Continued operation with the Transmission Temperature Warning Light illuminated could cause the fluid to boil over, come in contact with hot engine or exhaust components causing a fire that may result in personal injury. 28.
UNDERSTANDING YOUR INSTRUMENT PANEL 159 • Compass heading display (N, S, E, W, NE, NW, SE, SW) • Outside temperature display (°F or °C) • Trip computer functions • Audio mode displays – 12 preset Radio Stations or CD Title and Track number when playing • Tire Pressure Monitor System (TPMS) displays (if equipped) Electronic Vehicle Information Center (EVIC) The EVIC consists of the following: • System status • Vehicle information warning message displays • Personal Settings (Customer-Programmable Feature
160 UNDERSTANDING YOUR INSTRUMENT PANEL STEP Button Press and release the STEP button to advance Electronic Vehicle Information Center (EVIC) the display through the various Trip Functions Displays When the appropriate conditions exist, the EVIC displays or Personal settings. the following messages. COMPASS Button • Press and release the COMPASS button to display the compass heading and the out- • side temperature.
UNDERSTANDING YOUR INSTRUMENT PANEL 161 • Door(s) Ajar (with a single chime if vehicle is in Unless reset, this message will continue to display each time you turn the ignition switch to the ON/RUN motion) position. To turn off the message temporarily, press and • Trunk Ajar (with a single chime) release the MENU button. To reset the oil change indicator system (after performing the scheduled maintenance) • Headlights On perform the following procedure: • Key In Ignition 1.
162 UNDERSTANDING YOUR INSTRUMENT PANEL The Trip Functions mode displays the following informaTrip Functions Press and release the MENU button until one of the tion: following Trip Functions displays in the EVIC: • ECO (Fuel Saver Indicator) — If Equipped The ECO indicator will illuminate in the EVIC display.
UNDERSTANDING YOUR INSTRUMENT PANEL 163 and average fuel economy, according to the current fuel • Display Units In: tank level. DTE cannot be reset through the RESET To make your selection, press and release the RESET button. button until ENGLISH or METRIC appears. NOTE: Significant changes in driving style or vehicle To Reset The Display loading will greatly affect the actual drivable distance of Reset will only occur if a resettable function is currently displayed.
164 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: The system will display the last known outside temperature when starting the vehicle and may need to be driven several minutes before the updated temperature is displayed. Engine temperature can also affect the displayed temperature, therefore temperature readings are not updated when the vehicle is not moving. Automatic Compass Calibration This compass is self-calibrating, which eliminates the need to calibrate the compass manually.
UNDERSTANDING YOUR INSTRUMENT PANEL 165 Compass Variance Compass Variance is the difference between Magnetic North and Geographic North. To compensate for the differences, the variance should be set for the zone where the vehicle is driven, per the zone map. Once properly set, the compass will automatically compensate for the differences and provide the most accurate compass heading.
166 UNDERSTANDING YOUR INSTRUMENT PANEL 3. Press and release the STEP button until “Compass Press and release the MENU button until “Personal Variance” and the current Variance Value displays in the Settings” displays in the EVIC. EVIC. Press and release the STEP button to display the follow4.
UNDERSTANDING YOUR INSTRUMENT PANEL Remote Key Unlock When “Driver Door 1st Press” is selected, only the driver’s door will unlock on the first press of the Remote Keyless Entry (RKE) transmitter UNLOCK button. When Driver Door 1st Press is selected, you must press of the RKE transmitter UNLOCK button twice to unlock the passenger’s doors. When “All Doors 1st Press” is selected, all of the doors will unlock on the first press of the RKE transmitter UNLOCK button.
168 UNDERSTANDING YOUR INSTRUMENT PANEL headlights will also turn off when the wipers are turned off if they were turned on by this feature. To make your selection, press and hold the RESET button until ON or OFF appears. Illuminated Approach When this feature is selected, the headlights will activate and remain on for up to 90 seconds when the doors are unlocked with the remote keyless entry transmitter.
UNDERSTANDING YOUR INSTRUMENT PANEL SETTING THE ANALOG CLOCK 169 MEDIA CENTER 230 (REQ) — AM/FM STEREO RADIO AND 6–DISC CD/DVD CHANGER (MP3/WMA AUX JACK) NOTE: The radio sales code is located on the lower right side of the radio faceplate. 4 To set the analog clock, located at the top center of the instrument panel, press and hold the button in until the setting is correct. The clock will adjust slowly at first and then quicker the longer the button is held.
170 UNDERSTANDING YOUR INSTRUMENT PANEL to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make NOTE: The ignition switch must be in the ON or ACC another selection. Holding either button will bypass position to operate the radio. stations without stopping until you release it. Power Switch/Volume Control (Rotary) SCAN Button Push the ON/VOLUME control knob to turn on the Pressing the SCAN button causes the tuner to search for radio.
UNDERSTANDING YOUR INSTRUMENT PANEL 171 If your vehicle is not equipped with or this feature is not Clock Setting Procedure available on your vehicle, a “Not Equipped With 1. Press and hold the TIME button until the hours blink. Uconnect Phone” message will display on the radio 2. Adjust the hours by turning the right side TUNE/ screen. SCROLL control knob. Phone Button Uconnect™ Phone — If Equipped Press this button to operate the Uconnect™ Phone feature 3.
172 UNDERSTANDING YOUR INSTRUMENT PANEL INFO Button Press the INFO button for an RDS station (one with call letters displayed). The radio will return a Radio Text message broadcast from an FM station (FM mode only). Push the rotary TUNE/SCROLL control knob a second time and MID will display. Turn the TUNE/SCROLL control knob to the right or left to increase or decrease the mid-range tones.
UNDERSTANDING YOUR INSTRUMENT PANEL Push the rotary TUNE/SCROLL control knob again to exit setting tone, balance, and fade. MUSIC TYPE Button Pressing this button once will turn on the Music Type mode for five seconds. Pressing the MUSIC TYPE button or turning the TUNE/SCROLL control knob within five seconds will allow the program format type to be selected. Many radio stations do not currently broadcast Music Type information.
174 UNDERSTANDING YOUR INSTRUMENT PANEL Program Type Soft Soft Rock Soft Rhythm and Blues Sports Talk Top 40 Weather 16-Digit Character Display Soft Soft Rck Soft R & B Sports Talk Top 40 Weather By pressing the SEEK button when the Music Type icon is displayed, the radio will be tuned to the next frequency station with the same selected Music Type name. The Music Type function only operates when in the FM mode.
UNDERSTANDING YOUR INSTRUMENT PANEL 175 • DVD Play Options - Selecting the DVD Play Options • VES™ Power - Allows you to turn VES™ ON and will display the following: OFF (if equipped). • Subtitle – Repeatedly pressing SELECT will switch • VES™ Lock - Locks out rear VES™ remote controls (if subtitles to different subtitle languages that are equipped). available on the disc (if equipped).
176 UNDERSTANDING YOUR INSTRUMENT PANEL Menu Language — If Equipped Selecting this item will allow the user to choose the default startup DVD menu language (effective only if language supported by disc). If you want to select a language not listed, then scroll down and select ⬙other.⬙ Enter the four-digit country code using the TUNE/ SCROLL control knob to scroll up and down to select the number and then push to select.
UNDERSTANDING YOUR INSTRUMENT PANEL AutoPlay — If Equipped When this is set to On and a DVD video is inserted, it will bypass the DVD menu screen and automatically play the movie. In some rare cases, the DVD player may not auto-play the main title. In such cases, use the MENU button on the remote control to select desired title to play. NOTE: The user will have to set these defaults before loading a disc. If changes are made to these settings after a disc is loaded, changes will not be effective.
178 UNDERSTANDING YOUR INSTRUMENT PANEL Buttons 1 - 6 These buttons tune the radio to the stations that you commit to pushbutton memory {12 AM, 12 FM, and 12 Satellite (if equipped) stations}. DISC Button Pressing the DISC button will allow you to switch from AM/FM modes to Disc modes. Operation Instructions - (DISC MODE for CD and MP3/WMA Audio Play, DVD-VIDEO) The radio DVD player and many DVD discs are coded by geographic region. These region codes must match in order for the disc to play.
UNDERSTANDING YOUR INSTRUMENT PANEL 179 Radio display will show ⬙LOADING DISC⬙ when the disc The disc can be ejected with the radio and ignition OFF. is loading and “READING DISC” when the radio is SEEK Button (CD MODE) reading the disc. Press the right SEEK button for the next selection on the CD. Press the left SEEK button to return to the beginning CAUTION! of the current selection, or return to the beginning of the This CD player will accept 4–3/4 in (12 cm) discs only.
180 UNDERSTANDING YOUR INSTRUMENT PANEL RW/FF (CD MODE) Press and hold FF (Fast Forward) and the CD player will begin to fast forward until FF is released, or RW or another CD button is pressed. The RW (Rewind) button works in a similar manner. AM or FM Button (CD MODE) Switches the radio into the AM or FM radio mode. Supported Medium Formats (File Systems) The medium formats supported by the radio are ISO 9660 Level 1 and Level 2 and includes the Joliet extension.
UNDERSTANDING YOUR INSTRUMENT PANEL Multisession disc formats are supported by the radio. Multisession discs may contain combinations of normal CD audio tracks and computer files (including MP3/ WMA files). Discs created with an option such as ⬙keep disc open after writing⬙ are most likely multisession discs. The use of multisession for CD audio or MP3/ WMA playback may result in longer disc loading times. frequencies in the following table are supported.
182 UNDERSTANDING YOUR INSTRUMENT PANEL ID3 Tag information for artist, song title, and album title • Number of files and folders - Loading times will are supported for ID3 version 1 tags. ID3 version 2 is not increase with more files and folders supported by the radios. To increase the speed of disc loading, it is recommended Playlist files are not supported. MP3 Pro files are not to use CD-R media and single-session discs. To create a supported.
UNDERSTANDING YOUR INSTRUMENT PANEL 183 Pressing the AUX button will change the mode to auxilINFO Button (DISC Mode for MP3/WMA Play) Pressing the INFO button repeatedly will scroll through iary device if the AUX jack is connected. the following TAG information: Song Title, Artist, File NOTE: The AUX device must be turned on and the Name, and Folder Name (if available). device’s volume set to the proper level.
184 UNDERSTANDING YOUR INSTRUMENT PANEL TIME Button (Auxiliary Mode) Press the TIME button to change the display from elapsed playing time to time of day. The time of day will display for five seconds. Operating Instructions - Uconnect™ Phone (If Equipped) Refer to “Uconnect™ Phone” in the Uconnect™ User Manual located on the DVD for further details. RW/FF (Auxiliary Mode) No function.
UNDERSTANDING YOUR INSTRUMENT PANEL Macrovision This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only, unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.
186 UNDERSTANDING YOUR INSTRUMENT PANEL Clock Setting Procedure — RBZ Radio To Manually Set the Clock 1. Turn on the radio. Changing Daylight Savings Time When selected, this feature will display the time of day in daylight savings time. Proceed as follows to change the current setting: 2. Touch the screen where the time is displayed, the clock 1. Turn on the radio. setting menu will appear on the screen. 2. Touch the screen where the time is displayed. The 3.
UNDERSTANDING YOUR INSTRUMENT PANEL 187 2. Touch the screen where the time is displayed. The want to select, touch the screen where the word “Page” is displayed to view additional time zones in the menu. clock setting menu will appear on the screen. 3. When this feature is on, a check mark will appear in 5. Touch the screen where the word “Save” is displayed. the box next to the words “Show Time if Radio is Off.
188 UNDERSTANDING YOUR INSTRUMENT PANEL 4. To move the hour forward, touch the screen where the word “Hour” with the arrow pointing upward is displayed. To move the hour backward, touch the screen where the word “Hour” with the arrow pointing downward is displayed. 2. Touch the screen where “User Clock” is displayed, the clock setting menu will appear on the screen. 3. When this feature is on, a check mark will appear in the box next to the words “Daylight Savings.
UNDERSTANDING YOUR INSTRUMENT PANEL 189 Touch the screen where the words “Show Time if Radio is MEDIA CENTER 130 (RES) — AM/FM STEREO Off” are displayed to change the current setting. RADIO WITH CD PLAYER (MP3 AUX JACK) Changing the Time Zone 1. Turn on the radio. NOTE: The radio sales code is located on the lower right side of the radio faceplate. 2. Touch the screen where the time is displayed. 4 3. Touch the screen where “User Clock” is displayed, the clock setting menu will appear on the screen.
190 UNDERSTANDING YOUR INSTRUMENT PANEL SEEK Buttons Press and release the SEEK buttons to search for the next NOTE: The ignition switch must be in the ON or ACC listenable station in AM/FM mode. Press the right switch position to operate the radio. to seek up and the left switch to seek down. The radio Power Switch/Volume Control (Rotary) will remain tuned to the new station until you make Push the ON/VOLUME control knob to turn on the another selection. Holding either button will bypass radio.
UNDERSTANDING YOUR INSTRUMENT PANEL 191 4. Adjust the minutes using the right side TUNE/ Push the rotary TUNE/SCROLL control knob a second SCROLL control knob. Press the TUNE/SCROLL control time and MID will display. Turn the TUNE/SCROLL control knob to the right or left to increase or decrease the knob to save time change. mid-range tones. 5. To exit, press any button/knob, or wait five seconds. Push the rotary TUNE/SCROLL control knob a third RW/FF time and TREBLE will display.
192 UNDERSTANDING YOUR INSTRUMENT PANEL Push the rotary TUNE/SCROLL control knob again to You may add a second station to each pushbutton by repeating the above procedure with this exception: Press exit setting tone, balance, and fade. the SET/RND button twice and SET 2 will show in the AM/FM Button display window. Each button can be set for SET 1 and Press the buttons to select either AM or FM mode. SET 2 in both AM and FM.
UNDERSTANDING YOUR INSTRUMENT PANEL 193 If you insert a disc with the ignition ON and the radio ON, the unit will switch from radio to CD mode and begin to play when you insert the disc. The display will NOTE: show the track number, and index time in minutes and • The ignition switch must be in the ON or ACC seconds. Play will begin at the start of track 1. position to operate the radio.
194 UNDERSTANDING YOUR INSTRUMENT PANEL EJECT Button - Ejecting a CD Press the EJECT button to eject the CD. the current selection. Pressing and holding the SEEK button will allow faster scrolling through the tracks in CD and MP3 modes. TIME Button Press this button to change the display from a large CD If you have ejected a disc and have not removed it within playing time display to a small CD playing time display. 10 seconds, it will be reloaded.
UNDERSTANDING YOUR INSTRUMENT PANEL 195 SET/RND Button (Random Play Button) Press this button while the CD is playing to activate Random Play. This feature plays the selections on the compact disc in random order to provide an interesting change of pace. Supported Medium Formats (File Systems) The medium formats supported by the radio are ISO 9660 Level 1 and Level 2 and includes the Joliet extension.
196 UNDERSTANDING YOUR INSTRUMENT PANEL • Maximum number of characters in file/folder names: extension may cause playback problems. The radio is designed to recognize the file as an invalid MP3 and will • Level 1: 12 (including a separator ⬙.⬙ and a threenot play the file. character extension) When using the MP3 encoder to compress audio data to • Level 2: 31 (including a separator ⬙.⬙ and a threean MP3 file, the bit rate and sampling frequencies in the character extension) following table are supported.
UNDERSTANDING YOUR INSTRUMENT PANEL 197 ID3 Tag information for artist, song title, and album title • Number of files and folders - Loading times will are supported for version 1 ID3 tags. ID3 version 2 is not increase with more files and folders supported by the radios. To increase the speed of disc loading, it is recommended Playlist files are not supported. MP3 Pro files are not to use CD-R media and single-session discs. To create a supported.
198 UNDERSTANDING YOUR INSTRUMENT PANEL not loud enough, turn the device’s volume up. If the AUX audio sounds distorted, turn the device’s volume down. TIME Button (Auxiliary Mode) Press this button to change the display to time of day. The time of day will display for five seconds (when ignition is OFF). MEDIA CENTER 130 (RES/RSC) — AM/FM STEREO RADIO WITH CD PLAYER (MP3 AUX JACK) AND SIRIUS RADIO NOTE: The radio sales code is located on the lower right side of the radio faceplate.
UNDERSTANDING YOUR INSTRUMENT PANEL 199 Power Switch/Volume Control (Rotary) Voice Command System (Radio) — If Equipped Push the ON/VOLUME control knob to turn on the Refer to “Voice Command” in the Uconnect™ User radio. Push the ON/VOLUME control knob a second Manual located on the DVD for further details. time to turn off the radio.
200 UNDERSTANDING YOUR INSTRUMENT PANEL If your vehicle is not equipped with or this feature is not 5. To exit, press any button/knob or wait five seconds. available on your vehicle, a “Not Equipped With The clock can also be set by pressing the SETUP button. Uconnect” message will display on the radio screen.
UNDERSTANDING YOUR INSTRUMENT PANEL 201 Push the rotary TUNE/SCROLL control knob a fourth TUNE Control Turn the rotary TUNE/SCROLL control knob clockwise time and BALANCE will display. Turn the TUNE/ to increase or counterclockwise to decrease the frequency. SCROLL control knob to the right or left to adjust the sound level from the right or left side speakers.
202 UNDERSTANDING YOUR INSTRUMENT PANEL Toggle the MUSIC TYPE button to select the following format types: Program Type No program type or undefined Adult Hits Classical Classic Rock College Country Foreign Language Information Jazz News Nostalgia Oldies 16-Digit Character Display None Adlt Hit Classicl Cls Rock College Country Language Inform Jazz News Nostalga Oldies Program Type Personality Public Rhythm and Blues Religious Music Religious Talk Rock Soft Soft Rock Soft Rhythm and Blues Sports Talk To
UNDERSTANDING YOUR INSTRUMENT PANEL 203 station with the same selected Music Type name. The AM/FM Button Music Type function only operates when in the FM Press the button to select either AM or FM mode. mode. SET/RND Button — To Set the Pushbutton If a preset button is activated while in the Music Type Memory (Program Type) mode, the Music Type mode will be When you are receiving a station that you wish to commit to pushbutton memory, press the SET/RND exited and the radio will tune to the preset station.
204 UNDERSTANDING YOUR INSTRUMENT PANEL and 12 FM stations to be stored into pushbutton memory. • This radio is capable of playing compact discs (CD), The stations stored in SET 2 memory can be selected by recordable compact discs (CD-R), rewritable compact pressing the pushbutton twice. discs (CD-RW), compact discs with MP3 tracks and multisession compact discs with CD and MP3 tracks. Every time a preset button is used, a corresponding Inserting Compact Disc(s) button number will display.
UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! • This CD player will accept 4–3/4 in (12 cm) discs only. The use of other sized discs may damage the CD player mechanism. • Do not use adhesive labels. These labels can peel away and jam the player mechanism. • RES is a single CD player. Do not attempt to insert a second CD if one is already loaded. • Dual-media disc types (one side is a DVD, the other side is a CD) should not be used, and they can cause damage to the player.
206 UNDERSTANDING YOUR INSTRUMENT PANEL RW/FF Press and hold FF (Fast Forward) and the CD player will begin to fast forward until FF is released or RW or another CD button is pressed. The RW (Reverse) button works in a similar manner. Notes On Playing MP3 Files The radio can play MP3 files; however, acceptable MP3 file recording media and formats are limited. When writing MP3 files, pay attention to the following restrictions. AM/FM Button Press the button to select either AM or FM mode.
UNDERSTANDING YOUR INSTRUMENT PANEL 207 Multisession disc formats are supported by the radio. Multisession discs may contain combinations of normal Maximum number of folder levels: 8 CD audio tracks and computer files (including MP3 files). Discs created with an option such as ⬙keep disc open after Maximum number of files: 255 writing⬙ are most likely multisession discs. The use of Maximum number of folders.
208 UNDERSTANDING YOUR INSTRUMENT PANEL rates (VBR) are also supported. The majority of MP3 files Playback of MP3 Files use a 44.1 kHz sampling rate and a 192, 160, 128, 96 or When a medium containing MP3 data is loaded, the radio checks all files on the medium. If the medium VBR bit rates. contains a lot of folders or files, the radio will take more MPEG Sampling Bit Rate (kbps) time to start playing the MP3 files.
UNDERSTANDING YOUR INSTRUMENT PANEL LIST Button (CD Mode for MP3 Play) Pressing the LIST button will bring up a list of all folders on the disc. Scrolling up or down the list is done by turning the TUNE/SCROLL control knob. Selecting a folder by pressing the TUNE/SCROLL control knob will begin playing the files contained in that folder (or the next folder in sequence if the selection does not contain playable files). The folder list will time out after five seconds.
210 UNDERSTANDING YOUR INSTRUMENT PANEL TIME Button (Auxiliary Mode) Press this button to change the display to time of day. The time of day will display for five seconds (when the ignition is OFF). Uconnect™ Multimedia (SATELLITE RADIO) — IF EQUIPPED (REN/REQ/RER/RBZ/RES RADIOS ONLY) Satellite radio uses direct satellite-to-receiver broadcasting technology to provide clear digital sound, coast to Operating Instructions - Uconnect™ Phone coast.
UNDERSTANDING YOUR INSTRUMENT PANEL System Activation Sirius Satellite Radio service is pre-activated, and you may begin listening immediately to the one year of audio service that is included with the factory-installed satellite radio system in your vehicle. Sirius will supply a welcome kit that contains general information, including how to setup your on-line listening account. For further information, call the toll-free number 888-539-7474, or visit the Sirius web site at www.sirius.com, or at www.
212 UNDERSTANDING YOUR INSTRUMENT PANEL Satellite Antenna To ensure optimum reception, do not place items on the roof around the rooftop antenna location. Metal objects placed within the line of sight of the antenna will cause decreased performance. Larger luggage items such as bikes should be placed as far rearward as possible, within the loading design of the rack. Do not place items directly on or above the antenna. • Placing objects over or too close to the antenna can cause signal blockage.
UNDERSTANDING YOUR INSTRUMENT PANEL INFO Button Pressing the INFO button will cycle the display information between Artist, Song Title, and Composer (if available). Also, pressing and holding the INFO button for an additional three seconds will make the radio display the Song Title all of the time (press and hold again to return to normal display). 213 or turning the TUNE/SCROLL control knob within five seconds will allow the program format type to be selected.
214 UNDERSTANDING YOUR INSTRUMENT PANEL SET Button – To Set the Pushbutton Memory When you are receiving a channel that you wish to commit to pushbutton memory, press the SET button. The symbol SET 1 will now show in the display window. Select the button (1-6) you wish to lock onto this channel and press and release that button. If a button is not selected within five seconds after pressing the SET button, the channel will continue to play but will not be stored into pushbutton memory.
UNDERSTANDING YOUR INSTRUMENT PANEL 215 4 Opening the Rear Seat VES™ VES™ Video Screen • The LCD screen swings up from the rear of the armrest NOTE: Close the armrest after the LCD screen has been to allow the rear seat passenger(s) to view the display. raised to its viewing position. • The radio and DVD player controls allow front seat operation for easy setup in the case of younger rear seat passengers.
216 UNDERSTANDING YOUR INSTRUMENT PANEL • A battery-powered infrared remote control snaps into a molded compartment in the center console armrest upper storage bin. Audio/Video RCA Jacks (AUX Jacks) on the rear of the center console enable the monitor to display video directly from a video camera, connect video games for display on the screen, or play music directly from an MP3 player. 1. Video in (yellow) 2. Left audio in (white) 3.
UNDERSTANDING YOUR INSTRUMENT PANEL 217 are rocker-type switches with a pushbutton in the center Right-Hand Switch Functions of each switch. Reach behind the steering wheel to access • Press the top of the switch to increase the volume. the switches. • Press the bottom of the switch to decrease the volume. • Press the button in the center of the switch to change modes (i.e., AM, FM, etc.).
218 UNDERSTANDING YOUR INSTRUMENT PANEL Left-Hand Switch Functions for Media (i.e., CD) Operation CD/DVD DISC MAINTENANCE To keep a CD/DVD in good condition, take the following precautions: • Press the top of the switch once to listen to the next track. 1. Handle the disc by its edge; avoid touching the surface. • Press the bottom of the switch once either to listen to the beginning of the current track or to listen to the 2.
UNDERSTANDING YOUR INSTRUMENT PANEL 219 NOTE: If you experience difficulty in playing a particu- Manual Heating and Air Conditioning lar disc, it may be damaged (i.e., scratched, reflective coating removed, a hair, moisture or dew on the disc) oversized, or have protection encoding. Try a known good disc before considering disc player service. RADIO OPERATION AND CELLULAR PHONES Under certain conditions, the cellular phone being on in your vehicle can cause erratic or noisy performance from your radio.
220 UNDERSTANDING YOUR INSTRUMENT PANEL Blower Control Rotate this control to regulate the amount of air forced through the ventilation system in any mode. The blower speed increases as you move the control to the right from the “O” (OFF) position. There are four blower speeds. cooler temperatures while rotating right into the red area indicates warmer temperatures.
UNDERSTANDING YOUR INSTRUMENT PANEL 221 Panel Mix Air is directed through the outlets in the instrument Air is directed through the floor, defrost, and side panel. These outlets can be adjusted to direct airflow. window demist outlets. This setting works best in cold or snowy conditions that require extra heat to NOTE: The center instrument panel outlets can be the windshield.
222 UNDERSTANDING YOUR INSTRUMENT PANEL Recirculation Control • The A/C will engage automatically to prevent fogging Pressing the Recirculation Control button will when the recirculation button is pressed and the mode temporarily put the system in recirculation control is set to panel or Bi-Level. mode (10 minutes). This can be used when • Recirculated air is not allowed in Floor, Mix or Defrost outside conditions such as smoke, odors, dust, modes.
UNDERSTANDING YOUR INSTRUMENT PANEL Air Conditioning Control Automatic Temperature Control (ATC) — Press this button to engage the Air If Equipped Conditioning. A light will illuminate when the Air Conditioning System is engaged. Rotating the dial left into the blue area of the scale indicates cooler temperatures while rotating right into the red area indicates warmer temperatures. NOTE: The air conditioning compressor will not engage until the engine has been running for about 10 seconds.
224 UNDERSTANDING YOUR INSTRUMENT PANEL the desired comfort level require air conditioning, the Automatic Operation The Automatic Temperature Control system automati- system will automatically make the adjustment. cally maintains the climate in the cabin of the vehicle at You will experience the greatest efficiency by simply the comfort levels desired by the driver and passenger. allowing the system to function automatically. Selecting Operation of the system is quite simple.
UNDERSTANDING YOUR INSTRUMENT PANEL 225 • If your air conditioning performance seems lower than expected, check the front of the A/C condenser located in front of the radiator for an accumulation of dirt or insects. Clean with a gentle water spray from behind the radiator and through the condenser. Fabric front fascia protectors may reduce airflow to the condenser, reducing air conditioning performance.
226 UNDERSTANDING YOUR INSTRUMENT PANEL
UNDERSTANDING YOUR INSTRUMENT PANEL 227 The operator can override the AUTO mode setting to • Floor change airflow distribution by rotating the Mode Control Air is directed through the floor outlets with a knob (on the right) to one of the following positions. small amount flowing through the defrost and side window demist outlets. • Panel Air is directed through the outlets in the instrument • Mix Air is directed through the floor, defrost, and side panel. These outlets can be adjusted to direct airflow.
228 UNDERSTANDING YOUR INSTRUMENT PANEL • Air Conditioner Control Press this button to turn on the air conditioning during manual operation only. When the air conditioning is turned on, cool dehumidified air will flow through the outlets selected with the Mode control dial. Press this button a second time to turn OFF the air conditioning. An LED in the button illuminates when manual compressor operation is selected. • Recirculation Control The system will automatically control recirculation.
UNDERSTANDING YOUR INSTRUMENT PANEL • Most of the time, when in Automatic Operation, you can temporarily put the system into Recirculation Mode by pressing the Recirculation button. However, under certain conditions, while in Automatic Mode, the system is blowing air out the defrost vents. When these conditions are present, and the Recirculation button is pressed, the indicator will flash and then turn off. This tells you that you are unable to go into Recirculation Mode at this time.
230 UNDERSTANDING YOUR INSTRUMENT PANEL Window Fogging Interior fogging on the windshield can be quickly removed by turning the mode selector to Defrost. The Mix mode can be used to maintain a clear windshield and provide sufficient heating. If side window fogging becomes a problem, increase blower speed. Vehicle windows tend to fog on the inside in mild but rainy or humid weather.
UNDERSTANDING YOUR INSTRUMENT PANEL 231 Control Setting Suggestions for Various Weather Conditions 4
STARTING AND OPERATING CONTENTS 䡵 Starting Procedures . . . . . . . . . . . . . . . . . . . . 238 䡵 Automatic Transmission . . . . . . . . . . . . . . . . . 241 ▫ Automatic Transmission . . . . . . . . . . . . . . . 238 ▫ Key Ignition Park Interlock . . . . . . . . . . . . . 243 ▫ Normal Starting . . . . . . . . . . . . . . . . . . . . . 238 ▫ Brake/Transmission Interlock System . . . . . . 243 ▫ Extreme Cold Weather (Below ⫺20°F Or ⫺29°C) . . . . . . . . . . . . . . .
234 STARTING AND OPERATING 䡵 AutoStick威 — If Equipped . . . . . . . . . . . . . . . 248 䡵 Electronic Brake Control System . . . . . . . . . . . 259 ▫ Operation . . . . . . . . . . . . . . . . . . . . . . . . . 248 ▫ Anti-Lock Brake System (ABS) . . . . . . . . . . . 259 ▫ General Information . . . . . . . . . . . . . . . . . . 249 ▫ Traction Control System (TCS) . . . . . . . . . . . 259 䡵 Driving On Slippery Surfaces . . . . . . . . . . . . . 250 ▫ Brake Assist System (BAS) . . . . . . . . . . . .
STARTING AND OPERATING ▫ Tire Inflation Pressures . . . . . . . . . . . . . . . . 277 235 ▫ General Information . . . . . . . . . . . . . . . . . . 293 ▫ Radial-Ply Tires . . . . . . . . . . . . . . . . . . . . . 279 䡵 Fuel Requirements . . . . . . . . . . . . . . . . . . . . . 294 ▫ Compact Spare Tire . . . . . . . . . . . . . . . . . . . 279 ▫ 2.4L And 2.7L Engine . . . . . . . . . . . . . . . . . 294 ▫ Tire Spinning . . . . . . . . . . . . . . . . . . . . . . . 280 ▫ 3.5L Engine . . . . . . . . .
236 STARTING AND OPERATING ▫ Ethanol Fuel (E85) . . . . . . . . . . . . . . . . . . . 301 䡵 Vehicle Loading . . . . . . . . . . . . . . . . . . . . . . 305 ▫ Fuel Requirements . . . . . . . . . . . . . . . . . . . 301 ▫ Vehicle Certification Label . . . . . . . . . . . . . . 305 ▫ Selection Of Engine Oil For Flexible Fuel Vehicles (E85) And Gasoline Vehicles . . . . . . 302 ▫ Gross Vehicle Weight Rating (GVWR) . . . . . . 306 ▫ Starting . . . . . . . . . . . . . . . . . . . . . . . . . . .
STARTING AND OPERATING 237 ▫ Trailer And Tongue Weight . . . . . . . . . . . . . 312 䡵 Recreational Towing (Behind Motorhome, Etc.) . . . . . . . . . . . . . . . . 318 ▫ Towing Requirements . . . . . . . . . . . . . . . . . 313 ▫ Towing This Vehicle Behind Another Vehicle ▫ Towing Tips . . . . . . . . . . . . . . . . . . . . . . . . 317 (Flat Towing With All Four Wheels On The Ground) . . . . . . . . . . . . . . . . . . . . . . . . . . .
238 STARTING AND OPERATING STARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust the inside and outside mirrors, fasten your seat belt, and if present, instruct all other occupants to buckle their seat belts. WARNING! Never leave children alone in a vehicle. Leaving children in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Do not leave the keys in the ignition.
STARTING AND OPERATING motor will continue to run, and it will disengage automatically when the engine is running. If the engine fails to start, the starter will disengage automatically in 10 seconds. If this occurs, turn the ignition switch to the LOCK position, wait 10 to 15 seconds, then repeat the “Normal Starting” procedure. 239 WARNING! (Continued) WARNING! • Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transmission cannot be started this way.
240 STARTING AND OPERATING the way to the floor and hold it there while cranking the With Tip Start engine. This should clear any excess fuel in case the If the engine fails to start after you have followed the “Normal Starting” or “Extreme Cold Weather” proceengine is flooded. dures, it may be flooded. To clear any excess fuel, push CAUTION! the accelerator pedal all the way to the floor and hold it.
STARTING AND OPERATING 241 ENGINE BLOCK HEATER — IF EQUIPPED AUTOMATIC TRANSMISSION The engine block heater warms the engine, and permits CAUTION! quicker starts in cold weather. Connect the cord to a standard 110-115 Volt AC electrical outlet with a Damage to the transmission may occur if the followgrounded, three-wire extension cord.
242 STARTING AND OPERATING CAUTION! (Continued) WARNING! • Before shifting the shift lever into any gear, make sure your foot is firmly on the brake pedal. • It is dangerous to move the shift lever out of PARK or NEUTRAL if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in reverse. You could lose control of the vehicle and hit someone or something.
STARTING AND OPERATING WARNING! (Continued) • Unintended movement of a vehicle could injure those in and near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, you should always shift the vehicle into PARK, remove the key from the ignition, and apply the parking brake. Once the key is removed from the ignition, the shift lever is locked in the PARK position, securing the vehicle against unwanted movement.
244 STARTING AND OPERATING • Insert a key, screwdriver, or finger into the hole at the NOTE: If a malfunction occurs, the system will trap the front of the cup holder and push and hold the manual key in the ignition switch lock cylinder to warn you that this safety feature is inoperable. The engine can be started override release lever forward. and stopped, but the key cannot be removed until you • While holding the release lever forward, move the obtain service. shift lever from PARK to NEUTRAL.
STARTING AND OPERATING When parking on a flat surface, place the shift lever into the PARK position first, and then apply the parking brake. When parking on a hill, it is important to set the parking brake before placing the shift lever in PARK, otherwise the load on the transmission locking mechanism may make it difficult to move the shift lever out of PARK. As an added precaution, turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade.
246 STARTING AND OPERATING NEUTRAL This range is used when vehicle is standing for prolonged periods with engine running. Engine may be started in this range. Set the parking brake if you must leave the vehicle. WARNING! Do not coast in NEUTRAL and never turn off the ignition switch to coast down a hill. These are unsafe practices that limit your response to changing traffic or road conditions. You might lose control of the vehicle and have an accident.
STARTING AND OPERATING 247 NOTE: If your vehicle is equipped with AutoStick威, you can reduce the frequency of transmission shifting during heavy loading, hilly terrain, strong headwinds, or while towing. Under these conditions, selecting the appropriate gear in AutoStick威 will improve the performance and extend transmission life by reducing excessive shifting and heat build-up. LOW — Four-Speed Transmission This range should be used for engine braking when descending very steep grades.
248 STARTING AND OPERATING damage, the transmission automatically shifts into second gear (third gear for six–speed). The transmission remains in second gear (third gear for six–speed) despite the forward gear selected. PARK, REVERSE, and NEUTRAL will continue to operate. The Reset feature allows the vehicle to be driven to a dealer for service without damaging the transmission. NOTE: Even if the transmission can be reset, it is recommended that you visit a dealer at your earliest possible convenience.
STARTING AND OPERATING 249 the driver to select a higher or lower range of gears. • Starting out in second gear is helpful in snowy or icy Moving the shift lever to the left (-) triggers a downshift conditions. and to the right (+) an upshift. The gear position will • Avoid using speed control when AutoStick威 is endisplay in the instrument cluster on the transmission gaged. range indicator.
250 STARTING AND OPERATING • If the system detects a problem, it will disable the Traction AutoStick威 mode and the transmission will return to When driving on wet or slushy roads, it is possible for a wedge of water to build up between the tire and road the automatic mode until the problem is corrected. surface. This is hydroplaning and may cause partial or DRIVING ON SLIPPERY SURFACES complete loss of vehicle control and stopping ability.
STARTING AND OPERATING DRIVING THROUGH WATER Driving through water more than a few inches/ centimeters deep will require extra caution to ensure safety and prevent damage to your vehicle. Flowing/Rising Water WARNING! Do not drive on or across a road or path where water is flowing and/or rising (as in storm run-off). Flowing water can wear away the road or path’s surface and cause your vehicle to sink into deeper water. Furthermore, flowing and/or rising water can carry your vehicle away swiftly.
252 STARTING AND OPERATING CAUTION! (Continued) WARNING! • Driving through standing water may cause damage to your vehicle’s drivetrain components. Always inspect your vehicle’s fluids (i.e., engine oil, transmission, axle, etc.) for signs of contamination (i.e., fluid that is milky or foamy in appearance) after driving through standing water. Do not continue to operate the vehicle if any fluid appears contaminated, as this may result in further damage.
STARTING AND OPERATING POWER STEERING The standard power steering system will give you good vehicle response and increased ease of maneuverability in tight spaces. The system will provide mechanical steering capability if power assist is lost. If for some reason the power assist is interrupted, it will still be possible to steer your vehicle. Under these conditions, you will observe a substantial increase in steering effort, especially at very low vehicle speeds and during parking maneuvers.
254 STARTING AND OPERATING checked if a leak is suspected, abnormal noises are apparent, and/or the system is not functioning as anticipated. Coordinate inspection efforts through an authorized dealer. CAUTION! Do not use chemical flushes in your power steering system as the chemicals can damage your power steering components. Such damage is not covered by the New Vehicle Limited Warranty.
STARTING AND OPERATING 255 NOTE: • When the parking brake is applied and the transmission is placed in gear, the “Brake Warning Light” will flash. If vehicle speed is detected, a chime will sound to alert the driver. Fully release the parking brake before attempting to move the vehicle. • This light only shows that the parking brake is applied. It does not show the degree of brake application.
256 STARTING AND OPERATING WARNING! WARNING! (Continued) • Never use the PARK position as a substitute for the parking brake. Always apply the parking brake fully when parked to guard against vehicle movement and possible injury or damage. • Never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be seriously or fatally injured. • Do not leave the key in the ignition.
STARTING AND OPERATING computer to modulate the hydraulic pressure to prevent wheel lock-up and avoid skidding on slippery surfaces. WARNING! • Pumping of the anti-lock brakes will diminish their effectiveness and may lead to an accident. Pumping makes the stopping distance longer. Just press firmly on your brake pedal when you need to slow down or stop.
258 STARTING AND OPERATING portion of the brake system is not functioning and that self-check cycle to ensure that the ABS system is working service is required. However, the conventional brake properly. This self check occurs each time the vehicle is system will continue to operate normally if the “Brake started and accelerated past 7 mph (11 km/h). Warning Light” is not on. ABS is activated during braking under certain road or If the “Anti-Lock Brake Warning Light” is on, the brake stopping conditions.
STARTING AND OPERATING WARNING! The Anti-Lock Brake System contains sophisticated electronic equipment that may be susceptible to interference caused by improperly installed or high output radio transmitting equipment. This interference can cause possible loss of anti-lock braking capability. Installation of such equipment should be performed by qualified professionals. 259 together to enhance vehicle stability and control in various driving conditions and are commonly referred to as ESC.
260 STARTING AND OPERATING spinning faster than the other, the system will apply the brake of the spinning wheel. This will allow more engine torque to be applied to the wheel that is not spinning. This feature remains active even if TCS and ESC are in the “Partial Off” mode. Refer to “Electronic Stability Control (ESC)” in this section of this manual. Brake Assist System (BAS) The BAS is designed to optimize the vehicle’s braking capability during emergency braking maneuvers.
STARTING AND OPERATING 261 Hill Start Assist (HSA) – If Equipped The HSA system is designed to assist the driver in launching a vehicle on an incline. HSA will maintain the level of brake pressure the driver inputs for a short duration once the driver takes his foot off of the brake pedal. If the driver does not apply the throttle during this short duration, the system will release brake pressure and the vehicle will roll down the incline.
262 STARTING AND OPERATING The system will only work if the intended direction of the 2. Shift the transmission into NEUTRAL. vehicle and vehicle gear match. For example, if the 3. Apply the parking brake. intended direction is forward up a hill and the vehicle is in DRIVE and the activation criteria are met, HSA will 4. Start the engine. activate. 5. Release the clutch pedal. The system will work in REVERSE and all forward gears, 6. Rotate the steering wheel one-half turn to the left.
STARTING AND OPERATING 263 10. Repeat these steps if you want to return this feature path does not match the intended path, ESC applies the brake of the appropriate wheel to assist in counteracting to it’s previous setting. the oversteer or understeer condition EVIC Equipped Vehicles HSA is a Customer Programmable Feature on a EVIC • Over-steer - when the vehicle is turning more than appropriate for the steering wheel position. equipped vehicle.
264 STARTING AND OPERATING WARNING! • The Electronic Stability Control (ESC) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. • ESC cannot prevent accidents, including those resulting from excessive speed in turns, driving on very slippery surfaces, or hydroplaning. Only a safe, attentive, and skillful driver can prevent accidents.
STARTING AND OPERATING 265 • The ESC system will make buzzing or clicking sounds when it is active. This is normal; the sounds will stop when ESC becomes inactive following the maneuver that caused the ESC activation. feature described in the TCS section, has been disabled and the “ESC Off Indicator Light” will be illuminated. All other stability features of ESC function normally, with the exception of engine power reduction.
266 STARTING AND OPERATING NOTE: To improve the vehicle’s traction when driving TIRE SAFETY INFORMATION with snow chains, or starting off in deep snow, sand or Tire Markings gravel, it may be desirable to switch to the “Partial Off” mode by pressing the “ESC Off” switch. Once the situation requiring ESC to be switched to the “Partial Off” mode is overcome, turn ESC on again by momentarily pressing the “ESC Off” switch. This may be done while the vehicle is in motion. 1 — U.S.
STARTING AND OPERATING 267 NOTE: • LT (Light Truck) - Metric tire sizing is based on U.S. • P (Passenger) - Metric tire sizing is based on U.S. design standards. The size designation for LT-Metric design standards. P-Metric tires have the letter “P” tires is the same as for P-Metric tires except for the molded into the sidewall preceding the size designaletters “LT” that are molded into the sidewall precedtion. Example: P215/65R15 95H. ing the size designation. Example: LT235/85R16.
268 STARTING AND OPERATING Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ⴖ....blank....ⴖ = Passenger car tire based on European design standards LT = Light truck tire based on U.S. design standards T = Temporary spare tire 31 = Overall diameter in inches (in) 215 = Section width in millimeters (mm) 65 = Aspect ratio in percent (%) — Ratio of section height to section width of tire 10.
STARTING AND OPERATING 269 EXAMPLE: Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions — The maximum speed corresponding to the speed symbol should only be achieved under specified operating conditions (i.e.
270 STARTING AND OPERATING Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full TIN, including the date code, located on the white sidewall side of the tire. Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the outboard side, then you will find it on the inboard side of the tire.
STARTING AND OPERATING 271 Tire Terminology and Definitions Term B-Pillar Cold Tire Pressure Maximum Inflation Pressure Recommended Inflation Pressure Tire Placard Definition The vehicle B-Pillar is a structural member of the body located between the front and rear door (of a four-door vehicle) running from the sill to the roof. Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or driven less than 1 mile (1.
272 STARTING AND OPERATING Tire Loading and Tire Pressure Tire and Loading Information Placard Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar.
STARTING AND OPERATING This placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) total weight your vehicle can carry 3) tire size designed for your vehicle 4) cold tire inflation pressures for the front, rear, and spare tires. 273 axles must not be exceeded. For further information on GAWRs, vehicle loading, and trailer towing, refer to “Vehicle Loading” in this section.
274 STARTING AND OPERATING 3. Subtract the combined weight of the driver and pas- 6. If your vehicle will be towing a trailer, load from your sengers from XXX lbs or XXX kg. trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available 4. The resulting figure equals the available amount of cargo and luggage load capacity of your vehicle. cargo and luggage load capacity.
STARTING AND OPERATING 275 5
276 STARTING AND OPERATING WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.
STARTING AND OPERATING WARNING! (Continued) • Unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • Always drive with each tire inflated to the recommended cold tire inflation pressure. Economy Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement.
278 STARTING AND OPERATING CAUTION! After inspecting or adjusting the tire pressure, always reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Tire pressures change by approximately 1 psi (7 kPa) per 12°F (7°C) of air temperature change. Keep this in mind when checking tire pressure inside a garage, especially in the winter.
STARTING AND OPERATING 279 Tire Pressures for High Speed Operation Radial-Ply Tires The manufacturer advocates driving at safe speeds WARNING! within posted speed limits. Where speed limits or conditions are such that the vehicle can be driven at high Combining radial ply tires with other types of tires speeds, maintaining correct tire inflation pressure is very on your vehicle will cause your vehicle to handle important. Increased tire pressure and reduced vehicle poorly.
280 STARTING AND OPERATING WARNING! Temporary use spare tires are for emergency use only. With these tires, do not drive more than 50 mph (80 km/h). Temporary-use spare tires have limited tread life. When the tread is worn to the tread wear indicators, the temporary use spare tire needs to be replaced. Be sure to follow the warnings, which apply to your spare. Failure to do so could result in spare tire failure and loss of vehicle control.
STARTING AND OPERATING 281 Refer to “Freeing A Stuck Vehicle” in “What To Do In Emergencies” for further information. WARNING! Fast spinning tires can be dangerous. Forces generated by excessive wheel speeds may cause tire damage or failure. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 30 mph (48 km/h) or for more than 30 seconds continuously when you are stuck, and do not let anyone near a spinning wheel, no matter what the speed.
282 STARTING AND OPERATING Life of Tire Replacement Tires The service life of a tire is dependent upon varying The tires on your new vehicle provide a balance of many factors including but not limited to: characteristics. They should be inspected regularly for wear and correct cold tire inflation pressure.
STARTING AND OPERATING 283 WARNING! WARNING! (Continued) • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle. This can cause unpredictable handling and stress to steering and suspension components. You could lose control and have an accident resulting in serious injury or death.
284 STARTING AND OPERATING CAUTION! Damage to the vehicle may result if tire chains are used. SNOW TIRES Snow tires should be of the same size and type construction as the front tires. Consult the manufacturer of the snow tire to determine any maximum vehicle speed requirement associated with the tire. These tires should always be operated at the vehicle maximum capacity inflation pressures under any load condition.
STARTING AND OPERATING 285 The tire pressure will vary with temperature by about 1 psi (7 kPa) for every 12 F (7 C). This means that when the outside temperature decreases, the tire pressure will decrease. Tire pressure should always be set based on cold inflation tire pressure. This is defined as the tire pressure after the vehicle has not been driven for at least three hours, or driven less than 1 mile (1.6 km) after a three hour period.
286 STARTING AND OPERATING The TPM System will continue to warn the driver of low tire pressure as long as the condition exists, and will not turn off until the tire pressure is at or above the recommended cold placard pressure. Once the low tire pressure warning (Tire Pressure Monitoring Telltale Light) illuminates, you must increase the tire pressure to the recommended cold placard pressure in order for the “Tire Pressure Monitoring Telltale Light” to turn off.
STARTING AND OPERATING CAUTION! • The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equipment that is not of the same size, type, and/or style. Aftermarket wheels can cause sensor damage.
288 STARTING AND OPERATING • Seasonal temperature changes will affect tire pressure, Tire Pressure Monitoring Low Pressure Warnings The “Tire Pressure Monitoring Telltale Light” will and the TPMS will monitor the actual tire pressure in illuminate in the instrument cluster and a chime the tire. will sound when tire pressure is low in one or Base System more of the four active road tires.
STARTING AND OPERATING will repeat, providing the system fault still exists. The “Tire Pressure Monitoring Telltale Light” will turn off when the fault condition no longer exists. A system fault can occur due to any of the following: 289 NOTE: 1. The compact spare tire (if so equipped) does not have a tire pressure monitoring sensor. Therefore, the TPMS will not monitor the pressure in the compact spare tire. 1. Jamming due to electronic devices or driving next to 2.
290 STARTING AND OPERATING Telltale Light” will turn OFF, as long no tire pressure is below the low-pressure warning limit in any of the four active road tires. The vehicle may need to be driven for up to 20 minutes above 15 mph (25 km/h) in order for the TPMS to receive this information. NOTE: It is particularly important for you to check the tire pressure in all of the tires on your vehicle monthly and to maintain the proper pressure.
STARTING AND OPERATING Tire Pressure Monitoring Low Pressure Warnings The “Tire Pressure Monitoring Telltale Light” will illuminate in the instrument cluster and a chime will sound when tire pressure is low in one or more of the four active road tires. In addition, the Electronic Vehicle Information Center (EVIC) will display a graphic showing the pressure values of each tire with the low tire pressure values flashing.
292 STARTING AND OPERATING Check TPMS Warning When a system fault is detected, a chime will sound and the “Tire Pressure Monitoring Telltale Light” will flash on and off for 75 seconds and then remain on solid. In addition, the EVIC will display a ⬙CHECK TPM SYSTEM⬙ message for three seconds and then display dashes (- -) in place of the pressure value to indicate which sensor is not being received. If the ignition key is cycled, this sequence will repeat, providing the system fault still exists.
STARTING AND OPERATING 293 display a ⬙CHECK TPM SYSTEM⬙ message for three NOTE: 1. The compact spare tire (if so equipped) does not have seconds and then display dashes (- -) in place of the a tire pressure monitoring sensor. Therefore, the TPMS pressure value. will not monitor the pressure in the compact spare tire. 5. Once you repair or replace the original road tire, and 2.
294 STARTING AND OPERATING • This device must accept any interference received, 3.5L Engine The 3.5L engine is designed to meet all including interference that may cause undesired emissions regulations and provide satisfacoperation. tory fuel economy and performance when The tire pressure sensors are covered under one of the using high-quality unleaded gasoline havfollowing licenses: ing an octane range of 87 to 89. The manufacturer recommends the use of 89 octane United States . . . . . . . . . . . . . .
STARTING AND OPERATING Over 40 automobile manufacturers around the world have issued and endorsed consistent gasoline specifications (the World Wide Fuel Charter, WWFC) which define fuel properties necessary to deliver enhanced emissions, engine performance, and durability for your vehicle. The manufacturer recommends the use of gasolines that meet the WWFC specifications if they are available.
296 STARTING AND OPERATING NOTE: The 2.7L engine is now rated for E85 Ethanol • OBD II “Malfunction Indicator Light” on use (EXCEPT CALIFORNIA EMISSION STATES). Only • poor engine performance vehicles with the E-85 fuel filler door label can operate on E-85. Refer to “Flexible Fuel” in “Starting and Operating” • poor cold start and cold drivability for further information.
STARTING AND OPERATING MMT in Gasoline MMT is a manganese containing metallic additive that is blended into some gasoline to increase octane. Gasoline blended with MMT provides no performance advantage beyond gasoline of the same octane number without MMT. Gasoline blended with MMT reduces spark plug life and reduces emission system performance in some vehicles. The manufacturer recommends that gasoline without MMT be used in your vehicle.
298 STARTING AND OPERATING CAUTION! (Continued) • An out-of-tune engine, or certain fuel or ignition malfunctions, can cause the catalytic converter to overheat. If you notice a pungent burning odor or some light smoke, your engine may be out of tune or malfunctioning and may require immediate service. Contact your authorized dealer for service assistance. • The use of fuel additives, which are now being sold as octane enhancers, is not recommended.
STARTING AND OPERATING WARNING! (Continued) • Guard against carbon monoxide with proper maintenance. Have the exhaust system inspected every time the vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side windows fully open. • Keep the trunk closed when driving your vehicle to prevent carbon monoxide and other poisonous exhaust gases from entering the vehicle. 299 FLEXIBLE FUEL (2.
300 STARTING AND OPERATING NOTE: The 2.7L engine is now rated for E85 Ethanol use (EXCEPT CALIFORNIA EMISSION STATES). Only vehicles with the E85 fuel filler door label can operate on E85. Only vehicles with the E85 fuel filler door label can operate on E85.
STARTING AND OPERATING 301 Ethanol Fuel (E85) For best results, a refueling pattern that avoids alternatE85 is a mixture of approximately 85% fuel ethanol and ing between E85 and unleaded gasoline is recom15% unleaded gasoline. mended. WARNING! Ethanol vapors are extremely flammable and could cause serious personal injury. Never have any smoking materials lit in or near the vehicle when removing the fuel filler tube cap (gas cap) or filling the tank.
302 STARTING AND OPERATING • Some additives used in regular gasoline are not fully compatible with E85 and may form deposits in your engine. To eliminate driveability issues that may be caused by these deposits, a supplemental gasoline additive, such as MOPAR威 Injector Cleanup or Techron may be used. Selection Of Engine Oil For Flexible Fuel Vehicles (E85) and Gasoline Vehicles FFV vehicles operated on E85 require specially formulated engine oils.
STARTING AND OPERATING Replacement Parts Many components in your Flexible Fuel Vehicle (FFV) are designed to be compatible with ethanol. Always be sure that your vehicle is serviced with correct ethanol compatible parts. CAUTION! ADDING FUEL Fuel Filler Cap (Gas Cap) The gas cap is behind the fuel filler door, on the left rear quarter panel of the vehicle. If the gas cap is lost or damaged, be sure the replacement cap is for use with this vehicle.
304 STARTING AND OPERATING After removing the gas cap, place the gas cap tether cable over a hook on the inside of the fuel door. This keeps the gas cap suspended away from and protects the vehicle’s surface. CAUTION! • Damage to the fuel system or emission control system could result from using an improper fuel tank filler tube cap (gas cap). • A poorly fitting gas cap may cause the “Malfunction Indicator Light (MIL)” to turn on.
STARTING AND OPERATING 305 Loose Filler Cap Message If the vehicles diagnostic system determines that the fuel • Never add fuel when the engine is running. This is filler cap in loose, improperly installed, or damaged, a in violation of most state and federal fire regula- “gASCAP” message will be displayed in the instrument tions and doing so will cause the MIL to turn on. cluster. Tighten the gas cap until a “clicking” sound is • A fire may result if gasoline is pumped into a heard.
306 STARTING AND OPERATING The label contains the following information: • Name of manufacturer • Month and year of manufacture • Gross Vehicle Weight Rating (GVWR) • Gross Axle Weight Rating (GAWR) front • Gross Axle Weight Rating (GAWR) rear • Vehicle Identification Number (VIN) • Type of Vehicle • Month Day and Hour of Manufacture (MDH) Gross Axle Weight Rating (GAWR) The GAWR is the maximum capacity of the front and rear axles. Distribute the load over the front and rear axles evenly.
STARTING AND OPERATING The best way to figure out the total weight of your vehicle is to weigh it when it is fully loaded and ready for operation. Weigh it on a commercial scale to ensure that it is not over the GVWR. 307 the specified GVWR, you must redistribute the weight. Improper weight distribution can have an adverse effect on the way your vehicle steers and handles and the way the brakes operate. Figure out the weight on the front and rear of the vehicle TRAILER TOWING separately.
308 STARTING AND OPERATING Common Towing Definitions Gross Combination Weight Rating (GCWR) The following trailer towing related definitions will assist The GCWR is the total permissible weight of your vehicle you in understanding the following information: and trailer when weighed in combination. Gross Vehicle Weight Rating (GVWR) The GVWR is the total allowable weight of your vehicle. This includes driver, passengers, cargo, and tongue weight.
STARTING AND OPERATING WARNING! It is important that you do not exceed the maximum front or rear GAWR. A dangerous driving condition can result if either rating is exceeded. You could lose control of the vehicle and have an accident. 309 Frontal Area The frontal area is the maximum height multiplied by the maximum width of the front of a trailer.
310 STARTING AND OPERATING Trailer Hitch Classification The following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition. Refer to the Trailer Towing Weights (Maximum Trailer Weight Ratings) chart for the Max. GTW towable for your given drivetrain. Trailer Hitch Classification Definitions Class Max.
STARTING AND OPERATING 311 Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. Maximum Trailer Weight Ratings Max. GTW Max. Trailer Tongue Wt. Engine/Transmission Max. Frontal Area (Gross Trailer Wt.) (See Note 1) 2.4L/Auto See Note 2 1,000 lbs (450 kg) 100 lbs (45 kg) 2.7L/Auto See Note 2 1,500 lbs (680 kg) 150 lbs (68 kg) 3.5L/Auto 22 sq.ft. (2.0 sq.
312 STARTING AND OPERATING CAUTION! Towing a trailer with a larger than recommended frontal area could cause the engine to overheat or cause severe engine damage under extreme conditions. Trailer and Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% of the Gross Trailer Weight (GTW) on the tow hitch of your vehicle.
STARTING AND OPERATING NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options, or authorized dealer-installed options, must be considered as part of the total load on your vehicle. Refer to “Tire Safety Information/Tire and Loading Information Placard” in “Starting and Operating” for the maximum combined weight of occupants and cargo for your vehicle.
314 STARTING AND OPERATING WARNING! WARNING! (Continued) Improper towing can lead to an injury accident. Follow these guidelines to make your trailer towing as safe as possible: • Make certain that the load is secured in the trailer and that it will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control. You could lose control of your vehicle and have an accident.
STARTING AND OPERATING WARNING! (Continued) 3. GAWR 4. Trailer tongue weight rating for the trailer hitch utilized (This requirement may limit the ability to always achieve 10% of trailer tongue weight as a percentage of total trailer weight). 315 • Check for signs of tire wear or visible tire damage before towing a trailer. Refer to “Tires – General Information” in “Starting and Operating” for information on tread wear indicators and for proper inspection procedure.
316 STARTING AND OPERATING • An electronically actuated trailer brake controller is required when towing a trailer with electronically actuated brakes. When towing a trailer equipped with a hydraulic surge actuated brake system, an electronic brake controller is not required. • Trailer brakes are recommended for trailers over 1,000 lbs (450 kg) and required for trailers in excess of 2,000 lbs (907 kg).
STARTING AND OPERATING 317 If you REGULARLY TOW a trailer for more than 45 minutes of continuous operation, then change the automatic transmission fluid and filter according to the interval specified for “police, taxi, fleet, or frequent trailer towing.” Refer to “Maintenance Schedule” for the proper Make sure all trailer and vehicle lights are working maintenance intervals. properly — including hazard flashers.
318 STARTING AND OPERATING • Use speed control in flat terrain and with light loads to RECREATIONAL TOWING maximize fuel efficiency. (BEHIND MOTORHOME, ETC.) Cooling System Towing This Vehicle Behind Another Vehicle To reduce potential for engine and transmission over- (Flat towing with all four wheels on the ground) heating, take the following actions: • City Driving When stopped for short periods of time, shift the transmission into NEUTRAL and increase engine idle speed. • Highway Driving Reduce speed.
WHAT TO DO IN EMERGENCIES CONTENTS 䡵 Hazard Warning Flasher . . . . . . . . . . . . . . . . 321 ▫ Preparations For Jacking . . . . . . . . . . . . . . . 324 䡵 If Your Engine Overheats . . . . . . . . . . . . . . . . 321 ▫ Jacking Instructions . . . . . . . . . . . . . . . . . . . 324 ▫ Engine Oil Overheating 䡵 Jump-Starting . . . . . . . . . . . (2.4L Engine Only) — If Equipped . . . . . . . . 322 ▫ Preparations For Jump-Start 䡵 Jacking And Tire Changing . . . . . . . . . . . . . . .
320 WHAT TO DO IN EMERGENCIES 䡵 Towing A Disabled Vehicle . . . . . . . . . . . . . . . 335 ▫ Towing With The Ignition Key . . . . . . . . . . . 335 ▫ Towing Without The Ignition Key . . . . . . . . 336 ▫ Towing This Vehicle Behind Another Vehicle . . . . . . . . . . . . . . . . . . . . . 336 ▫ Towing This Vehicle Behind Another Vehicle With A Tow Dolly . . . . . . . . . . . . . . . . . . . . 336 ▫ Towing Without Power — Override Transaxle Interlock System . . . . . . . . . . . . . .
WHAT TO DO IN EMERGENCIES 321 HAZARD WARNING FLASHER IF YOUR ENGINE OVERHEATS The Hazard Warning flasher switch is located on the In any of the following situations, you can reduce the instrument panel, below the radio. potential for overheating by taking the appropriate action. Press the switch to turn on the Hazard Warning flasher. When the switch is activated, all directional • On the highways — Slow down.
322 WHAT TO DO IN EMERGENCIES NOTE: There are steps that you can take to slow down an impending overheat condition: • If your air conditioner (A/C) is on, turn it off. The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat. • You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high.
WHAT TO DO IN EMERGENCIES JACKING AND TIRE CHANGING WARNING! • Being under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never put any part of your body under a vehicle that is on a jack. Never start or run the engine while the vehicle is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift. • The jack is designed to use as a tool for changing tires only.
324 WHAT TO DO IN EMERGENCIES Preparations For Jacking 1. Park the vehicle on a firm, level surface. Avoid ice or slippery areas. WARNING! Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. 2. Set the parking brake. 3. Place the shift lever into PARK (automatic transaxle) or REVERSE (manual transaxle). 4. Turn OFF the ignition. 5.
WHAT TO DO IN EMERGENCIES 325 WARNING! (Continued) WARNING! (Continued) • Always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle. • Block the wheel diagonally opposite the wheel to be raised. • Set the parking brake firmly and set an automatic transmission in PARK; a manual transmission in REVERSE. • Never start or run the engine with the vehicle on a jack. • Do not let anyone sit in the vehicle when it is on a jack.
326 WHAT TO DO IN EMERGENCIES NOTE: The jack handle attaches to the side of the jack 2. Loosen, but do not remove, the wheel nuts by turning with two attachment points. When the jack is partially them to the left one turn while the wheel is still on the expanded, the tension between the two attachment ground. points holds the jack handle in place. CAUTION! Do not attempt to raise the vehicle by jacking on locations other than those indicated in Step 3. 3.
WHAT TO DO IN EMERGENCIES 327 6 Front Jacking Location Rear Jacking Location 4. Turn the jack screw to the left until the jack can be placed under the jacking location. Once the jack is positioned, turn the jack screw to the right until the jack head is properly engaged with the lift area closest to the wheel to be changed. Do not raise the vehicle until you are sure the jack is securely engaged.
328 WHAT TO DO IN EMERGENCIES WARNING! WARNING! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. To avoid possible personal injury, handle the wheel covers with care to avoid contact with any sharp edges. 7. Lower the vehicle by turning the jack screw to the left. 5. Raise the vehicle by turning the jack screw to the right, using the swivel wrench.
WHAT TO DO IN EMERGENCIES WARNING! A loose tire or jack thrown forward in a collision or hard stop could endanger the occupants of the vehicle. Always stow the jack parts and the spare tire in the places provided. 329 JUMP-STARTING If your vehicle has a discharged battery it can be jumpstarted using a set of jumper cables and a battery in another vehicle or by using a portable battery booster pack.
330 WHAT TO DO IN EMERGENCIES WARNING! Do not attempt jump-starting if the battery is frozen. It could rupture or explode and cause personal injury. Preparations for Jump-Start The battery in your vehicle is located between the left front headlight assembly and the left front wheel splash shield. To allow jump-starting there are remote battery posts located on the left side of the engine compartment.
WHAT TO DO IN EMERGENCIES WARNING! • Take care to avoid the radiator cooling fan whenever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan blades. • Remove any metal jewelry such as watch bands or bracelets that might make an inadvertent electrical contact. You could be seriously injured. • Batteries contain sulfuric acid that can burn your skin or eyes and generate hydrogen gas which is flammable and explosive.
332 WHAT TO DO IN EMERGENCIES WARNING! 1. Connect the positive (+) end of the jumper cable to the remote positive (+) post of the discharged vehicle. Do not allow vehicles to touch each other as this could establish a ground connection and personal injury could result. 2. Connect the opposite end of the positive (+) jumper cable to the positive (+) post of the booster battery.
WHAT TO DO IN EMERGENCIES 5. Start the engine in the vehicle that has the booster battery, let the engine idle a few minutes, and then start the engine in the vehicle with the discharged battery. 333 10. Reinstall the protective cover over the remote positive (+) battery post of the discharged vehicle.
334 WHAT TO DO IN EMERGENCIES front wheels. Then shift back and forth between REVERSE and FIRST gear. Using minimal accelerator pedal pressure to maintain the rocking motion, without spinning the wheels, is most effective. NOTE: If your vehicle is equipped with Electronic Stability Control (ESC), turn the system to Partial OFF before attempting to “rock” the vehicle. Refer to “Electronic Brake Control” in “Starting and Operating” for further information.
WHAT TO DO IN EMERGENCIES TOWING A DISABLED VEHICLE 335 CAUTION! (Continued) Towing With The Ignition Key Front Wheel Drive Your vehicle may be towed (with all four wheels flat on the ground), under the following conditions: • The shift lever must be in NEUTRAL. • The distance to be traveled must not exceed 15 miles (25 km). • The towing speed must not exceed 25 mph (40 km/h). CAUTION! • Exceeding these towing limits may cause a transaxle failure.
336 WHAT TO DO IN EMERGENCIES If you must use the accessories (wipers, defrosters, etc.) while being towed, the key must be in the ON position, not the ACC position. Make certain the transaxle remains in NEUTRAL. Towing Without The Ignition Key Special care must be taken when the vehicle is towed with the ignition in the LOCK position. Flatbed towing is the preferred towing method. However, if a flatbed towing vehicle is not available, a wheel lift towing vehicle may be used.
WHAT TO DO IN EMERGENCIES 337 Towing Without Power — Override Transaxle • Insert the ignition key and rotate it to the ON position. Interlock System • Remove the cupholder liner. Special care must be taken when the vehicle is towed with the ignition in the LOCK position. A dolly should be • Insert a key, screwdriver, or similar object into the used under the front wheels if the rear wheels are raised.
MAINTAINING YOUR VEHICLE CONTENTS 䡵 Engine Compartment — 2.4L . . . . . . . . . . . . . 341 䡵 Maintenance Procedures . . . . . . . . . . . . . . . . . 347 䡵 Engine Compartment — 2.7L . . . . . . . . . . . . . 342 ▫ Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . 348 䡵 Engine Compartment — 3.5L . . . . . . . . . . . . . 343 ▫ Engine Oil Filter . . . . . . . . . . . . . . . . . . . . . 351 䡵 Onboard Diagnostic System — OBD II . . . . . . 344 ▫ Engine Air Cleaner Filter . . . . . . . . . .
340 MAINTAINING YOUR VEHICLE ▫ Adding Washer Fluid . . . . . . . . . . . . . . . . . 358 䡵 Bulb Replacement . . . . . . . . . . . . . . . . . . . . . 383 ▫ Exhaust System . . . . . . . . . . . . . . . . . . . . . 358 ▫ Headlamp . . . . . . . . . . . . . . . . . . . . . . . . . 383 ▫ Cooling System . . . . . . . . . . . . . . . . . . . . . 361 ▫ Front Turn Signal/Parking Lamp . . . . . . . . . 385 ▫ Brake System . . . . . . . . . . . . . . . . . . . . . . . 366 ▫ Front Fog Lamp . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 341 ENGINE COMPARTMENT — 2.
342 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT — 2.
MAINTAINING YOUR VEHICLE 343 ENGINE COMPARTMENT — 3.
344 MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated Onboard Diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as maintaining engine emissions well within current government regulations.
MAINTAINING YOUR VEHICLE the gas cap is properly tightened. Press the trip odometer “Reset” button to turn off the message. If the problem persists, the message will appear the next time the vehicle is started. This might indicate a damaged cap. If the problem is detected twice in a row, the system will turn on the “Malfunction Indicator Light (MIL).” Resolving the problem will turn the MIL light off. 345 Normally, the OBD II system will be ready.
346 MAINTAINING YOUR VEHICLE 4. Approximately 15 seconds later, one of two things will Regardless of whether your vehicle’s OBD II system is happen: ready or not, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced a. The MIL will flash for about 10 seconds and then before going to the I/M station. The I/M station can fail return to being fully illuminated until you turn OFF your vehicle because the MIL is on with the engine the ignition or start the engine.
MAINTAINING YOUR VEHICLE 347 your vehicle. Refer to these Service Manuals before MAINTENANCE PROCEDURES The pages that follow contain the required maintenance attempting any procedure yourself. services determined by the engineers who designed your NOTE: Intentional tampering with emissions control vehicle. systems may void your warranty and could result in civil Besides those maintenance items specified in the fixed penalties being assessed against you.
348 MAINTAINING YOUR VEHICLE CAUTION! (Continued) • Your vehicle has been built with improved fluids that protect the performance and durability of your vehicle and also allow extended maintenance intervals. Do not use chemical flushes in these components as the chemicals can damage your engine, transmission, power steering or air conditioning. Such damage is not covered by the New Vehicle Limited Warranty.
MAINTAINING YOUR VEHICLE CAUTION! Do not overfill the engine. Overfilling the engine will cause oil aeration, which can lead to loss of oil pressure and an increase in oil temperature. This could damage your engine. Change Engine Oil The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Refer to “Maintenance Schedule” for further information.
350 MAINTAINING YOUR VEHICLE CAUTION! Do not use chemical flushes in your engine oil as the chemicals can damage your engine. Such damage is not covered by the New Vehicle Limited Warranty. Engine Oil Viscosity (SAE Grade) – 2.4L and 2.7L Engines SAE 5W-20 engine oil is recommended for all operating temperatures. This engine oil improves low temperature starting and vehicle fuel economy. Your engine oil filler cap also shows the recommended engine oil viscosity for your vehicle.
MAINTAINING YOUR VEHICLE 351 Lubricants which do not have both, the engine oil certi- Disposing of Used Engine Oil and Oil Filters fication mark and the correct SAE viscosity grade num- Care should be taken in disposing of used engine oil and oil filters from your vehicle. Used oil and oil filters, ber should not be used. indiscriminately discarded, can present a problem to the Synthetic Engine Oils environment.
352 MAINTAINING YOUR VEHICLE Engine Air Cleaner Filter WARNING! The air induction system (air cleaner, hoses, etc.) can provide a measure of protection in the case of engine backfire. Do not remove the air induction system (air cleaner, hoses, etc.) unless such removal is necessary for repair or maintenance. Make sure that no one is near the engine compartment before starting the vehicle with the air induction system (air cleaner, hoses, etc.) removed.
MAINTAINING YOUR VEHICLE 353 WARNING! CAUTION! • Battery fluid is a corrosive acid solution and can burn or even blind you. Do not allow battery fluid to contact your eyes, skin, or clothing. Do not lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area immediately with large amounts of water. • Battery gas is flammable and explosive. Keep flame or sparks away from the battery.
354 MAINTAINING YOUR VEHICLE Air Conditioner Maintenance For best possible performance, your air conditioner should be checked and serviced by an authorized dealer at the start of each warm season. This service should include cleaning of the condenser fins and a performance test. CAUTION! Do not use chemical flushes in your air conditioning system as the chemicals can damage your air conditioning components. Such damage is not covered by the New Vehicle Limited Warranty.
MAINTAINING YOUR VEHICLE Refrigerant Recovery and Recycling R-134a air conditioning refrigerant is a hydrofluorocarbon (HFC) that is endorsed by the Environmental Protection Agency and is an ozone-saving product. However, the manufacturer recommends that air conditioning service be performed by authorized dealers or other service facilities using recovery and recycling equipment. 355 The A/C Air Filter is located in the fresh air inlet behind the glove box.
356 MAINTAINING YOUR VEHICLE 5. Disengage the two retaining tabs that secure the filter 7. Install the A/C Air Filter with the arrow on the filter cover to the HVAC housing and remove the cover. pointing toward the floor. When installing the filter cover, make sure the retaining tabs fully engage the cover. CAUTION! The A/C Air Filter is labeled with an arrow to indicate airflow direction through the filter. Failure to install the filter properly will result in the need to replace it more often. 8.
MAINTAINING YOUR VEHICLE quiet, easy operation and to protect against rust and wear. Prior to the application of any lubricant, the parts concerned should be wiped clean to remove dust and grit; after lubricating excess oil and grease should be removed. Particular attention should also be given to hood latching components to ensure proper function. When performing other underhood services, the hood latch, release mechanism and safety catch should be cleaned and lubricated.
358 MAINTAINING YOUR VEHICLE present please proceed to clean wiper blades with humid Exhaust System cloth removing any debris that may be affecting its The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust function. system. Adding Washer Fluid The fluid reservoir for the windshield washers is located If you notice a change in the sound of the exhaust system; in the engine compartment.
MAINTAINING YOUR VEHICLE 359 WARNING! CAUTION! • Exhaust gases can injure or kill. They contain carbon monoxide (CO), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing CO, refer to “Safety Tips/Exhaust Gas” in “Things To Know Before Starting Your Vehicle” for further information. • A hot exhaust system can start a fire if you park over materials that can burn.
360 MAINTAINING YOUR VEHICLE Under normal operating conditions, the catalytic con- To minimize the possibility of catalytic converter damverter will not require maintenance. However, it is im- age: portant to keep the engine properly tuned to assure • Do not shut off the engine or interrupt the ignition, proper catalyst operation and prevent possible catalyst when the transmission is in gear and the vehicle is in damage. motion.
MAINTAINING YOUR VEHICLE Cooling System WARNING! • When working near the radiator cooling fan, disconnect the fan motor lead or turn the ignition switch to the LOCK position. The fan is temperature controlled and can start at anytime the ignition switch is in the ON position. • You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator. If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.
362 MAINTAINING YOUR VEHICLE Selection Of Coolant Use only the manufacturer’s recommended coolant. Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for further information. CAUTION! • Mixing of engine coolant (antifreeze) other than specified HOAT engine coolant (antifreeze), may result in engine damage and may decrease corrosion protection.
MAINTAINING YOUR VEHICLE replacement. To prevent reducing this extended maintenance period, it is important that you use the same engine coolant (antifreeze) throughout the life of your vehicle. 363 (antifreeze) solution. The use of lower quality water will reduce the amount of corrosion protection in the engine cooling system.
364 MAINTAINING YOUR VEHICLE WARNING! rules for your community. To prevent ingestion by animals or children, do not store ethylene glycol based engine coolant (antifreeze) in open containers or allow it to remain in puddles on the ground. If ingested by a child or pet, seek emergency assistance immediately. Clean up any ground spills immediately. • The warning words “DO NOT OPEN HOT” on the cooling system pressure cap are a safety precaution.
MAINTAINING YOUR VEHICLE The radiator normally remains completely full, so there is no need to remove the radiator cap unless checking for engine coolant (antifreeze) freeze point or replacing coolant. Advise your service attendant of this. As long as the engine operating temperature is satisfactory, the coolant bottle need only be checked once a month. When additional engine coolant (antifreeze) is needed to maintain the proper level, it should be added to the coolant bottle. Do not overfill.
366 MAINTAINING YOUR VEHICLE • Make sure that the radiator and coolant recovery bottle overflow hoses are not kinked or obstructed. • Keep the front of the radiator clean. If your vehicle is equipped with air conditioning, keep the front of the condenser clean. WARNING! Riding the brakes can lead to brake failure and possibly an accident. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage.
MAINTAINING YOUR VEHICLE Clean the top of the master cylinder area before removing the cap. If necessary, add fluid to bring the fluid level up to the requirements described on the brake fluid reservoir. Overfilling of fluid is not recommended because it may cause leaking in the system. Fluid level can be expected to fall as the brake pads wear. Brake fluid level should be checked when pads are replaced. However, low fluid level may be caused by a leak and a checkup may be needed.
368 MAINTAINING YOUR VEHICLE WARNING! (Continued) WARNING! (Continued) • To avoid contamination from foreign matter or moisture, use only new brake fluid or fluid that has been in a tightly closed container. Keep the master cylinder reservoir cap secured at all times. Brake fluid in a open container absorbs moisture from the air resulting in a lower boiling point. This may cause it to boil unexpectedly during hard or prolonged braking, resulting in sudden brake failure. This could result in a accident.
MAINTAINING YOUR VEHICLE 369 driven at least 15 miles (24 km). Hot fluid cannot be held Fluid Level Check – 2.4L and 2.7L Engines Use the following procedure to check the automatic comfortably between the fingertips. Cold fluid is at a transmission fluid level properly: temperature below 80°F (27° C). 1. Park the vehicle on level ground. 2. Run the engine at curb idle speed for a minimum of 60 seconds. 3. Apply the parking brake fully. 4.
370 MAINTAINING YOUR VEHICLE CAUTION! • Using a transmission fluid other than the manufacturer’s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder. Using a transmission fluid other than that recommended by the manufacturer will result in more frequent fluid and filter changes. Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for further information. • Dirt and water in the transmission can cause serious damage.
MAINTAINING YOUR VEHICLE CAUTION! Do not use chemical flushes in your transmission as the chemicals can damage your transmission components. Such damage is not covered by the New Vehicle Limited Warranty. 371 The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle. What Causes Corrosion? Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle.
372 MAINTAINING YOUR VEHICLE Washing • Wash your vehicle regularly. Always wash your vehicle in the shade using MOPAR威 Car Wash or equivalent, or a mild car wash soap, and rinse the panels completely with clear water. • If insects, tar, or other similar deposits have accumulated on your vehicle, use MOPAR威 Super Kleen Bug and Tar Remover or equivalent to remove.
MAINTAINING YOUR VEHICLE 373 • If you detect any stone chips or scratches in the paint, Wheel and Wheel Trim Care touch them up immediately. The cost of such repairs is All wheels and wheel trim, especially aluminum and chrome-plated wheels, should be cleaned regularly with considered the responsibility of the owner. a mild soap and water to prevent corrosion.
374 MAINTAINING YOUR VEHICLE To minimize the possibility of scratching the lenses and • For grease stains, apply MOPAR威 Multi-Purpose reducing light output, avoid wiping with a dry cloth. To Cleaner or equivalent to a clean, damp cloth and remove road dirt, wash with a mild soap solution folremove the stain. Use a fresh, damp towel to remove lowed by rinsing. soap residue.
MAINTAINING YOUR VEHICLE if absolutely necessary. Do not use harsh cleaners or Armor All威. Use MOPAR威 Total Clean or equivalent to clean vinyl upholstery. Cleaning Leather Upholstery MOPAR威 Total Clean or equivalent is specifically recommended for leather upholstery. Your leather upholstery can be best preserved by regular cleaning with a damp soft cloth. Small particles of dirt can act as an abrasive and damage the leather upholstery and should be removed promptly with a damp cloth.
376 MAINTAINING YOUR VEHICLE Replace the belts if they appear frayed or worn or if the Cleaning Plastic Instrument Cluster Lenses The lenses in front of the instruments in this vehicle are buckles do not work properly. molded in clear plastic. When cleaning the lenses, care Dry with a soft tissue. must be taken to avoid scratching the plastic. Cleaning Center Console Cupholders 1. Clean with a wet, soft rag.
MAINTAINING YOUR VEHICLE 377 Installation Align the liner in the cupholder and press down firmly. FUSES Totally Integrated Power Module (TIPM) The TIPM is located in the engine compartment near the air cleaner assembly. This center contains cartridge fuses and mini fuses. A label that identifies each component may be printed on the inside of the cover. Refer to the graphic below for FUSES/TIPM location.
378 MAINTAINING YOUR VEHICLE Cavity Cartridge Fuse 3 — 4 — 5 — 6 — 7 — 8 — Mini Fuse Description Battery Feed – Center 10 Amp High Mounted Stop Red Light (CHMSL)/Brake Switch 10 Amp Battery Feed – Ignition Red Switch 20 Amp Trailer Tow – Yellow If Equipped Ignition Off Draw 10 Amp (IOD) – Power Mirror Red Switch/Climate Controls 30 Amp Ignition Off Draw Green (IOD) Sense 1 30 Amp Ignition Off Draw Green (IOD) Sense 2 Cavity Cartridge Fuse 9 40 Amp Green 10 — 11 — 12 — 13 — Min
MAINTAINING YOUR VEHICLE Cavity 14 Cartridge Fuse — Mini Fuse 10 Amp Red 15 40 Amp Green — 16 — 15 Amp Lt.
380 MAINTAINING YOUR VEHICLE Cavity 26 27 28 Cartridge Fuse — — — 29 — 30 — Mini Description Fuse 15 Amp Auto Shutdown (ASD) Lt.
MAINTAINING YOUR VEHICLE Cavity Cartridge Fuse 35 40 Amp Green 36 30 Amp Pink 37 — Mini Fuse Description Battery Feed – AntiLock Brakes (ABS) Module – If Equipped/ — Electronic Stability Control (ESC) Module – If Equipped Battery Feed – Passenger Door Module — (PDM)/Driver Door Module (DDM) 25 Amp Power Top Module – Natural If Equipped 381 CAUTION! • When installing the Totally Integrated Power Module cover, it is important to ensure the cover is properly positioned and fully latched.
382 MAINTAINING YOUR VEHICLE VEHICLE STORAGE LIGHT BULBS – Interior Bulb No. If you will not be using your vehicle for more than Front Courtesy/Reading Lamp . . . . . . . . . . 578/W5W 21 days, you may want to take steps to preserve your Center Courtesy/Reading Lamp. . . . . . . . . . 578/W5W battery. Visor Vanity Lamp. . . . . . . . . . . . . . . . . . . . . . A6220 • Disengage the mini-fuse in the Power Distribution Glove Box Lamp . . . . . . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE LIGHT BULBS – Exterior Bulb No. Low Beam Headlamp . . . . . . . . . . . . . . . . . . . . . H11 High Beam Headlamp . . . . . . . . . . . . . . . . . . . . 9005 Front Park/Turn Signal/Side Marker Lamp . . . . 3757A Front Fog Lamp . . . . . . . . . . . . . . . . . . . . . . PSX24W Center High Mounted Stop (CHMSL) Lamp . . . . . . . . . . . . . . . . . . . W16W (921) Rear Tail/Stop Lamp . . . . . . . . . . . . . . . . . . . . . 3157 Rear Turn Signal Lamp. . . . . . . . . . . . . . . .
384 MAINTAINING YOUR VEHICLE 3. Rotate bulb and connector one-quarter turn and pull 4. Pull the bulb out of the socket and replace the bulb. outward from assembly. CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. 5. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol. 6. Reinsert the bulb and socket assembly and rotate clockwise one-quarter turn to secure.
MAINTAINING YOUR VEHICLE Front Turn Signal/Parking Lamp 1. Raise and prop open the hood. 385 3. Remove the bulb from the connector socket and install the replacement bulb. 4. Install the bulb and connector assembly into the 2. Rotate the bulb’s electrical connector one-quarter turn headlamp housing and rotate the connector one-quarter counterclockwise and remove it from the headlamp turn clockwise to lock it in place. housing.
386 MAINTAINING YOUR VEHICLE 1. Rotate the bulb’s electrical connector one-quarter turn 2. Remove the bulb from the connector socket and install counterclockwise and remove it from the fog lamp hous- the replacement bulb. ing. CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with an oily surface, clean the bulb with rubbing alcohol. 3.
MAINTAINING YOUR VEHICLE Tail/Stop, Rear Turn Signal and Backup Lamps The taillamps are a two piece design. The turn signal, brake and taillamps are located in the rear corner body panel housing. The backup and taillamps are located in the trunk lid housing. 387 Changing the Tail/Stop Lamp or Rear Turn Signal Lamp 1.
388 MAINTAINING YOUR VEHICLE 2. Remove the two plastic wing nuts from the taillamp 4. Rotate the applicable bulb’s electrical connector onehousing. quarter turn counterclockwise and remove it from the taillamp housing. 3. Grasp the taillamp housing and pull it firmly outward while pushing gently on the studs from inside to disengage the housing from the vehicle. 1 — Tail/Stop Lamp 2 — Turn Signal Lamp 5. Remove the bulb from the connector socket and install the replacement bulb.
MAINTAINING YOUR VEHICLE 389 6. Install the bulb and connector assembly into the taillamp housing and rotate the connector one-quarter turn clockwise to lock it in place. 7. Reinstall the taillamp housing. Changing the Backup Lamp 1. Open the trunk. 2. Rotate the bulb’s electrical connector one-quarter turn counterclockwise and remove it from the housing.
390 MAINTAINING YOUR VEHICLE 3. Remove the bulb from the connector socket and install the replacement bulb. 4. Install the bulb and connector assembly into the housing and rotate the connector one-quarter turn clockwise to lock it in place. License Plate Lamp 1. Remove two retaining screws holding the lamp lens in place. 2. Gently pry the lens loose. 3. Pull bulb from socket, replace and reattach the lamp lens with the two retaining screws.
MAINTAINING YOUR VEHICLE Center High-Mounted Stop Lamp (CHMSL) 1. Open the trunk lid. 391 3. Remove the bulb from the connector socket and install the replacement bulb. 4. Install the bulb and connector assembly into the 2. Rotate the bulb’s electrical connector one-quarter turn CHMSL housing and rotate the connector one-quarter counterclockwise and remove it from the CHMSL housturn clockwise to lock it in place. ing.
392 MAINTAINING YOUR VEHICLE FLUID CAPACITIES U.S. Fuel (Approximate) All Engines — (Except 2.4L PZEV) 16.9 Gallons 2.4L PZEV (Partial Zero Emissions Vehicle) 18.5 Gallons Engine Oil with Filter 2.4L Engine (SAE 5W-20, API Certified) 4.5 Quarts 2.7L Engine (SAE 5W-20, API Certified) 5.5 Quarts 3.5L Engine (SAE 10W-30, API Certified) 5.5 Quarts Cooling System* 2.4L Engine (MOPAR威 Antifreeze/Coolant 5 7.7 Quarts Year/100,000 Mile Formula or equivalent) 2.7L Engine (MOPAR威 Antifreeze/Coolant 5 9.
MAINTAINING YOUR VEHICLE 393 FLUIDS, LUBRICANTS, AND GENUINE PARTS Engine Component Engine Coolant Engine Oil – 2.4L and 2.7L Engines Engine Oil – 3.5L Engine Engine Oil Filter Spark Plugs – 2.4L Engine except PZEV* Spark Plugs – 2.4L with PZEV* Fluid, Lubricant, or Genuine Part MOPAR威 Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) or equivalent. Use API Certified SAE 5W-20 Engine Oil, meeting the requirements of Chrysler Material Standard MS-6395.
394 MAINTAINING YOUR VEHICLE Component Fluid, Lubricant, or Genuine Part Spark Plugs – 2.7L Engine TE10PMC5 (Gap 0.050 in [1.27 mm]) Spark Plugs – 3.5L Engine ZFR5LP-13G (Gap 0.050 in [1.27 mm]) Fuel Selection – 2.4L and 2.7L En87 Octane gines Fuel Selection – 3.
MAINTENANCE SCHEDULES CONTENTS 䡵 Emissions Control System Maintenance . . . . . . 396 䡵 Maintenance Schedule . . . . . . . . . . . . . . . . . . 396 ▫ Required Maintenance Intervals . . . . . . . . . .
M A I N T E N A N C E 396 MAINTENANCE SCHEDULES EMISSIONS CONTROL SYSTEM MAINTENANCE The Scheduled Maintenance services listed in bold type must be done at the times or mileages specified to ensure the continued proper functioning of the emissions control system. These and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
MAINTENANCE SCHEDULES NOTE: • The oil change indicator message will not monitor the time since the last oil change. Change your vehicles oil if it has been six months since your last oil change even if the oil change indicator message is NOT illuminated. • Change your engine oil more often if you drive your vehicle off-road for an extended period of time. • Under no circumstances should oil change intervals exceed 6,000 miles (10 000 km) or six months, whichever comes first.
M A I N T E N A N C E 398 MAINTENANCE SCHEDULES Once a Month • Check tire pressure and look for unusual wear or • Change the engine oil filter. damage. • Inspect the brake hoses and lines. • Inspect the battery and clean and tighten the terminals CAUTION! as required. • Check the fluid levels of coolant reservoir, brake master cylinder, and transmission and add as needed. S C H • Check all lights and other electrical items for correct E operation.
MAINTENANCE SCHEDULES 6,000 Miles (10,000 km) or 6 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. Odometer Reading Repair Order # Signature Authorized Chrysler Dealer Date Dealer Code 399 M 12,000 Miles (20,000 km) or 12 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle in dusty or off-road conditions, inspect the engine air cleaner filter, and replace if necessary.
M 400 MAINTENANCE SCHEDULES A I 18,000 Miles (30,000 km) or N T 18 Months Maintenance E Service Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate tires. C E 24,000 Miles (40,000 km) or 24 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle in dusty or off-road conditions, inspect the engine air cleaner filter, and replace if necessary. ❏ Inspect the brake linings, and replace as necessary.
MAINTENANCE SCHEDULES 30,000 Miles (50,000 km) or 30 Months Maintenance Service Schedule 36,000 Miles (60,000 km) or 36 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ Replace the engine air cleaner filter. ❏ Replace the spark plugs (2.4L Engine except PZEV*). ❏ Adjust parking brake on vehicles equipped with four wheel disc brakes.
M 402 MAINTENANCE SCHEDULES A I 42,000 Miles (70,000 km) or N T 42 Months Maintenance E Service Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate tires. C E 48,000 Miles (80,000 km) or 48 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle in dusty or off-road conditions, inspect the engine air cleaner filter, and replace if necessary. ❏ Inspect the brake linings, and replace as necessary.
MAINTENANCE SCHEDULES 54,000 Miles (90,000 km) or 54 Months Maintenance Service Schedule 60,000 Miles (100,000 km) or 60 Months Maintenance Service Schedule ❏ ❏ ❏ ❏ ❏ ❏ ❏ Change the engine oil and engine oil filter. Rotate tires. Replace the engine air cleaner filter. Replace the spark plugs (2.4L Engine except PZEV*). Inspect the brake linings, and replace as necessary. Replace the air conditioning filter (if equipped).
M 404 MAINTENANCE SCHEDULES A I 66,000 Miles (110,000 km) or N T 66 Months Maintenance E Service Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate tires. C E 72,000 Miles (120,000 km) or 72 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle in dusty or off-road conditions, inspect the engine air cleaner filter, and replace if necessary. ❏ Inspect the brake linings, and replace as necessary.
MAINTENANCE SCHEDULES 78,000 Miles (130,000 km) or 78 Months Maintenance Service Schedule 84,000 Miles (140,000 km) or 84 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle in dusty or off-road conditions, inspect the engine air cleaner filter, and replace if necessary. ❏ Inspect the brake linings, and replace as necessary. ❏ Replace the air conditioning filter (if equipped).
M 406 MAINTENANCE SCHEDULES A I 90,000 Miles (150,000 km) or N T 90 Months Maintenance E Service Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate tires. C ❏ Replace the engine air cleaner filter. E S C H E D U L E S 8 96,000 Miles (160,000 km) or 96 Months Maintenance Service Schedule ❏ Replace the spark plugs (2.4L Engine except PZEV*). ❏ Inspect and replace the PCV valve, if necessary†. ❏ Adjust parking brake on vehicles equipped with four wheel disc brakes.
MAINTENANCE SCHEDULES 102,000 Miles (170,000 km) or 102 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ Replace the spark plugs (2.4L PZEV*, 2.7L and 3.5L Engines). ❏ Replace the timing belt (3.5L Engine). ❏ Flush and replace the engine coolant. ❏ Inspect accessory drive belt, replace if necessary.
M 408 MAINTENANCE SCHEDULES A I 114,000 Miles (190,000 km) or N T 114 Months Maintenance E Service Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate tires. C E S C H E D U L E S 8 Odometer Reading Repair Order # Signature Authorized Chrysler Dealer Date Dealer Code 120,000 Miles (200,000 km) or 120 Months Maintenance Service Schedule ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ Change the engine oil and engine oil filter. Rotate tires. Replace the engine air cleaner filter. Replace the spark plugs (2.
MAINTENANCE SCHEDULES 126,000 Miles (210,000 km) or 126 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. Odometer Reading Repair Order # Signature Authorized Chrysler Dealer Date Dealer Code 409 M 132,000 Miles (220,000 km) or 132 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle in dusty or off-road conditions, inspect the engine air cleaner filter, and replace if necessary.
M 410 MAINTENANCE SCHEDULES A I 138,000 Miles (230,000 km) or N T 138 Months Maintenance E Service Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate tires. C E S C H E D U L E S 8 Odometer Reading Repair Order # Signature Authorized Chrysler Dealer Date Dealer Code 144,000 Miles (240,000 km) or 144 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires.
MAINTENANCE SCHEDULES 150,000 Miles (250,000 km) or 150 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ Replace the engine air cleaner filter. ❏ Replace the spark plugs (2.4L Engine except PZEV*). ❏ Adjust parking brake on vehicles equipped with four wheel disc brakes.
M A I N T E N A N C E S C H E D U L E S 8 412 MAINTENANCE SCHEDULES * PZEV = Partial Zero Emission Vehicle † This maintenance is recommended by the manufacturer to the owner, but is not required to maintain emissions warranty. WARNING! • You can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS 䡵 Suggestions For Obtaining Service For Your Vehicle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 415 ▫ Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) . . . . . . . . . . . . 417 ▫ Prepare For The Appointment . . . . . . . . . . . 415 ▫ Service Contract . . . . . . . . . . . . . . . . . . . . . 417 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . 415 䡵 Warranty Information . . . . . . . . . . . . . . . . . .
414 IF YOU NEED CONSUMER ASSISTANCE 䡵 Department Of Transportation Uniform Tire Quality Grades . . . . . . . . . . . . . . . . . . . . . . . . 421 ▫ Treadwear . . . . . . . . . . . . . . . . . . . . . . . . . 421 ▫ Traction Grades . . . . . . . . . . . . . . . . . . . . . 421 ▫ Temperature Grades . . . . . . . . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE 415 the service advisor and list the items in order of priority. At many authorized dealers, you may obtain a rental vehicle at a minimal daily charge. If you need a rental, it Prepare For The Appointment is advisable to make these arrangements when you call If you’re having warranty work done, be sure to have the for an appointment. right papers with you. Take your warranty folder. All work to be performed may not be covered by the IF YOU NEED ASSISTANCE warranty.
416 IF YOU NEED CONSUMER ASSISTANCE This is why you should always talk to an authorized Chrysler Group LLC Customer Center dealer’s service manager first. Most matters can be re- P.O. Box 21–8004 Auburn Hills, MI 48321–8004 solved with this process. Phone: (800) 247–9753 • If for some reason you are still not satisfied, talk to the general manager or owner of the authorized dealer- Chrysler Canada Inc. Customer Center P.O. Box 1621 ship. They want to know if you need assistance.
IF YOU NEED CONSUMER ASSISTANCE Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommunication Devices for the Deaf) equipment at its customer center. Any hearing or speech impaired customer, who has access to a TDD or a conventional teletypewriter (TTY) in the United States, can communicate with the manufacturer by dialing 1–800–380–CHRY.
418 IF YOU NEED CONSUMER ASSISTANCE We appreciate that you have made a major investment when you purchased the vehicle. An authorized dealer has also made a major investment in facilities, tools, and training to assure that you are absolutely delighted with the ownership experience. You’ll be pleased with their sincere efforts to resolve any warranty issues or related concerns.
IF YOU NEED CONSUMER ASSISTANCE If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your authorized dealer, and the manufacturer. To contact NHTSA, you may either call the Auto Safety Hotline toll free at 1–888–327–4236 (TTY: 1–800–424– 9153), or go to http://www.safercar.
420 IF YOU NEED CONSUMER ASSISTANCE NOTE: A street address is required when ordering manuals (no P.O. Boxes). • Service Manuals to find and fix problems on computer-controlled vehicle systems and features. They show exactly how to find and correct problems the first time, using step-bystep troubleshooting and drivability procedures, proven diagnostic tests and a complete list of all tools and equipment.
IF YOU NEED CONSUMER ASSISTANCE Call toll free at: • 1–800–890–4038 (U.S.) • 1–800–387–1143 (Canada) Or Visit us on the Worldwide Web at: • www.techauthority.com DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES The following tire grading categories were established by the National Highway Traffic Safety Administration. The specific grade rating assigned by the tire’s manufacturer in each category is shown on the sidewall of the tires on your vehicle.
422 IF YOU NEED CONSUMER ASSISTANCE WARNING! The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics. Temperature Grades The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel.
INDEX 10
424 INDEX About Your Brakes . . . . . . . . . . . . . . . . . . . . . . . 254 ABS (Anti-Lock Brake System) . . . . . . . . . . . . . . 256 Adding Engine Coolant (Antifreeze) . . . . . . . . . . 362 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 303 Adding Washer Fluid . . . . . . . . . . . . . . . . . . . . . 358 Additives, Fuel . . . . . . . . . . . . . . . . . . . . . . . . . 297 Air Cleaner, Engine (Engine Air Cleaner Filter) . . . 352 Air Conditioner Maintenance . . . . . . . . . .
INDEX 425 B-Pillar Location . . . . . . . . . . . . . . . . . . . . . . . . 272 Brake Assist System . . . . . . . . . . . . . . . . . . . . . . 260 Brake, Parking . . . . . . . . . . . . . . . . . . . . . . . . . . 254 Brake System . . . . . . . . . . . . . . . . . . . . . . . . . . . 366 Anti-Lock (ABS) . . . . . . . . . . . . . . . . . . . . . . . 256 Fluid Check . . . . . . . . . . . . . . . . . . . . . . . 366,394 Master Cylinder . . . . . . . . . . . . . . . . . . . . . . . 366 Parking . . . . . . .
426 INDEX Caps, Filler Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 303 Oil (Engine) . . . . . . . . . . . . . . . . . . 341,342,343,350 Power Steering . . . . . . . . . . . . . . . . . . . . . . . . 253 Radiator (Coolant Pressure) . . . . . . . . . . . . . . . 363 Car Washes . . . . . . . . . . . . . . . . . . . . . . . . . . . . 372 Carbon Monoxide Warning . . . . . . . . . . . . . . . 81,298 Cargo Area Features . . . . . . . . . . . . . . . . . . . . . . 134 Cargo Compartment . .
INDEX Console, Floor . . . . . . . . . . . . . . . . . . . . . . . 103,135 Contract, Service . . . . . . . . . . . . . . . . . . . . . . . . 417 Coolant Pressure Cap (Radiator Cap) . . . . . . . . . . 363 Cooling System . . . . . . . . . . . . . . . . . . . . . . . . . 361 Adding Coolant (Antifreeze) . . . . . . . . . . . . . . 362 Coolant Capacity . . . . . . . . . . . . . . . . . . . . . . 392 Coolant Level . . . . . . . . . . . . . . . . . . . . . . 361,364 Disposal of Used Coolant . . . . . . . . . . .
428 INDEX Door Locks, Automatic . . . . . . . . . . . . . . . . . . . . 30 Emergency Trunk Release . . . . . . . . . . . . . . . . . 37,38 Door Opener, Garage . . . . . . . . . . . . . . . . . . . . . 120 Emission Control System Maintenance . . . . . . 345,396 Engine . . . . . . . . . . . . . . . . . . . . . . . . . . 341,342,343 Driving Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . 352 On Slippery Surfaces . . . . . . . . . . . . . . . . . . . 250 Block Heater . . . . . . . . . . . . .
INDEX 429 Automatic Transaxle . . . . . . . . . . . . . . . . . . . . 370 Oil Selection . . . . . . . . . . . . . . . . . . . . . . . 349,392 Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . 351,393 Oil Synthetic . . . . . . . . . . . . . . . . . . . . . . . . . 351 Engine Oil Disposal . . . . . . . . . . . . . . . . . . . . 351 Overheating . . . . . . . . . . . . . . . . . . . . . . . . . . 321 Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 238 Flashers . . . . . . . . . . .
430 INDEX Fluid Level Checks Automatic Transaxle . . . . . . . . . . . . . . . . . 369,370 Brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . 366,394 Cooling System . . . . . . . . . . . . . . . . . . . . . . . 361 Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . 348 Power Steering . . . . . . . . . . . . . . . . . . . . . 253,394 Fluids . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 393 Fluids, Lubricants and Genuine Parts . . . . . . . . . .
INDEX 431 Head Restraints . . . . . . . . . . . . . . . . . . . . . . . . . . 98 Headlights . . . . . . . . . . . . . . . . . . . . . . . . . . . . 383 Bulb Replacement . . . . . . . . . . . . . . . . . . . . . . 383 Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . 373 High Beam . . . . . . . . . . . . . . . . . . . . . . . . 108,158 High Beam/Low Beam Select Switch . . . . . . . . 108 On With Wipers . . . . . . . . . . . . . . . . . . . . . . . 115 Passing . . . . . . . . . . . . . . . .
432 INDEX Ignition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Ignition Key Removal . . . . . . . . . . . . . . . . . . . . . 12 Illuminated Entry . . . . . . . . . . . . . . . . . . . . . . . . 20 Immobilizer (Sentry Key) . . . . . . . . . . . . . . . . . . . 15 Infant Restraint . . . . . . . . . . . . . . . . . . . . . .
INDEX LATCH (Lower Anchors and Tether for CHildren) . . . . . . . 75 Latches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84 Hood . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104 Lead Free Gasoline . . . . . . . . . . . . . . . . . . . . . . 294 Leaks, Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84 Life of Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . 282 Light Bulbs . . . . . . . . . . . . . . . . . . . . . . . . . . 84,382 Lights . . . .
434 INDEX Maintenance Procedures . . . . . . . . . . . . . . . . . . . 347 Maintenance Schedule . . . . . . . . . . . . . . . . . . . . 396 Malfunction Indicator Light (Check Engine) . . 156,345 Manual, Service . . . . . . . . . . . . . . . . . . . . . . . . . 419 Map/Reading Lights . . . . . . . . . . . . . . . . . . . . . 111 Master Cylinder (Brakes) . . . . . . . . . . . . . . . . . . 366 Methanol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 295 Mini-Trip Computer . . . . . . . . . . . . .
INDEX New Vehicle Break-In Period . . . . . . . . . . . . . . . . 79 Occupant Restraints . . . . . . . . . . . . . . . . . . . . . 60,64 Occupant Restraints (Sedan) . . . . . . . . . 38,56,57,60,63 Octane Rating, Gasoline (Fuel) . . . . . . . . . . . . . . 294 Odometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149 Trip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149,152 Oil Change Indicator . . . . . . . . . . . . . . . . 151,161,396 Oil Change Indicator, Reset . . . . . . . .
436 INDEX Phone, Cellular . . . . . . . . . . . . . . . . . . . . . . . . . . 93 Phone, Hands-Free (Uconnect™) . . . . . . . . . . . . . . 93 Placard, Tire and Loading Information . . . . . . . . . 272 Power Deck Lid Release . . . . . . . . . . . . . . . . . . . . . . . 36 Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 Outlet (Auxiliary Electrical Outlet) . . . . . . . . . . 129 Seats . . . . . . . . . . . . . . .
INDEX Remote Sound System (Radio) Controls . . . . . . . . 216 Remote Starting System . . . . . . . . . . . . . . . . . . . . 26 Remote Trunk Release . . . . . . . . . . . . . . . . . . . . . 36 Replacement Bulbs . . . . . . . . . . . . . . . . . . . . . . . 382 Replacement Keys . . . . . . . . . . . . . . . . . . . . . . . . 16 Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . 346 Replacement Tires . . . . . . . . . . . . . . . . . . . . . . . 282 Reporting Safety Defects . . . . . . . . . .
438 INDEX Untwisting Procedure . . . . . . . . . . . . . . . . . . . . 44 Seat Belts (Sedan) . . . . . . . . . . . . . . . . . . . . . . . . 38 Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93 Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . 94 Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103 Heated . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101 Lumbar Support . . . . . . . . . . . . . . . . . . . . . . . 96 Power . . . . . . . .
INDEX Starting Procedures . . . . . . . . . . . . . . . . . . . . . . 238 Steering Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 253 Tilt Column . . . . . . . . . . . . . . . . . . . . . . . . . . 116 Wheel, Tilt . . . . . . . . . . . . . . . . . . . . . . . . . . . 116 Steering Wheel Mounted Sound System Controls . . . . . . . . . . . . . . . . . . . . . . . . . 216 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133,382 Storage, Vehicle . . . . . . . . . . . . . . . .
440 INDEX Life of Tires . . . . . . . . . . . . . . . . . . . . . . . . . . 282 Load Capacity . . . . . . . . . . . . . . . . . . . . . 272,273 Pressure Monitor System (TPMS) . . . . . . . . . . . 285 Pressure Warning Light . . . . . . . . . . . . . . . . . . 155 Quality Grading . . . . . . . . . . . . . . . . . . . . . . . 421 Radial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 279 Replacement . . . . . . . . . . . . . . . . . . . . . . . . . 282 Rotation . . . . . . . . . . . . . . . . .
INDEX Transmitter Battery Service (Remote Keyless Entry) . . . . . . . . . . . . . . . . . . . . 25 Transmitter, Garage Door Opener (HomeLink威) . . 120 Transmitter Programming (Remote Keyless Entry) . . . . . . . . . . . . . . . . . . . . 25 Transporting Pets . . . . . . . . . . . . . . . . . . . . . . . . 79 Tread Wear Indicators . . . . . . . . . . . . . . . . . . . . 281 Trip Odometer . . . . . . . . . . . . . . . . . . . . . . . . . . 149 Trip Odometer Reset Button . . . . . . . . . . . . . . . .
442 INDEX Warranty Information . . . . . . . . . . . . . . . . . . . . . 418 Washer, Adding Fluid . . . . . . . . . . . . . . . . . . . . . 358 Washers, Windshield . . . . . . . . . . . . . . . . 112,114,358 Washing Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . 372 Water Driving Through . . . . . . . . . . . . . . . . . . . . . . 251 Wheel and Wheel Trim . . . . . . . . . . . . . . . . . . . . 373 Wheel and Wheel Trim Care . . . . . . . . . . . . . . . . 373 Wind Buffeting . . . . . . . . . .
Chrysler Group LLC 10C41-126-AC 3rd Edition Printed in U.S.A.
