SECTION TABLE OF CONTENTS PAGE 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 2 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85 3 4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION 1 CONTENTS 䡵 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 Vehicle Identification Number .............. 6 䡵 How To Use This Manual . . . . . . . . . . . . . . . . . . 4 䡵 Vehicle Modifications/Alterations . . . . . . . . . . . . 7 䡵 Warnings And Cautions . . . . . . . . . . . . . . . . . . .
INTRODUCTION INTRODUCTION Congratulations on selecting your new Chrysler Group LLC vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. This Owner’s Manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your vehicle.
INTRODUCTION 5 1
INTRODUCTION WARNINGS AND CAUTIONS This Owner’s Manual contains WARNINGS against operating procedures that could result in an accident or bodily injury. It also contains CAUTIONS against procedures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important information. Observe all Warnings and Cautions.
INTRODUCTION 7 VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS 䡵 A Word About Your Keys . . . . . . . . . . . . . . . . . 12 䡵 Vehicle Security Alarm — If Equipped . . . . . . . . 18 ▫ Ignition Key Removal . . . . . . . . . . . . . . . . . . 12 ▫ Rearming The System . . . . . . . . . . . . . . . . . . 18 ▫ Key-In-Ignition Reminder . . . . . . . . . . . . . . . 14 ▫ To Arm The System . . . . . . . . . . . . . . . . . . . 18 ▫ Locking The Doors With The Key . . . . . . . . . . 14 ▫ To Disarm The System . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Using The Remote Open Window Feature — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 24 ▫ Using The Panic Alarm . . . . . . . . . . . . . . . . . 24 ▫ Programming Additional Transmitters . . . . . . 25 ▫ Transmitter Battery Replacement . . . . . . . . . . 25 ▫ General Information . . . . . . . . . . . . . . . . . . . 26 䡵 Remote Start System — If Equipped . . . . . . . . . 26 ▫ How To Use Remote Start . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 ▫ Rear Seat Belts . . . . . . . . . . . . . . . . . . . . . . . 47 ▫ Advanced Front Airbag Features . . . . . . . . . . 56 ▫ Automatic Locking Retractors (ALR) Mode — If Equipped . . . . . . . . . . . . . . 47 ▫ Airbag Deployment Sensors And Controls . . . 61 ▫ Seat Belt Pretensioners — If Equipped . . . . . . 48 ▫ Supplemental Rear Impact Active Head Restraints (AHR) . . . . . . . . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS The authorized dealer that sold you your vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys from your authorized dealer. Ask your authorized dealer for these numbers and keep them in a safe place. You can insert the double-sided keys into the locks with either side up. Vehicle Key Ignition Key Removal Automatic Transaxle Place the shift lever in PARK.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 occurs, rotate the key to the right slightly, then remove the key as described. If a malfunction occurs, the system will trap the key in the ignition switch lock cylinder to warn you that this safety feature is inoperable. The engine can be started and stopped, but the key cannot be removed until you obtain service.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE feature is programmable. For details, refer to “Key-Off Key-In-Ignition Reminder Power Delay,” under “Personal Settings (Customer-Pro- Opening the driver’s door when the key is in the ignition, grammable Features)” under “Electronic Vehicle Infor- sounds a signal to remind you to remove the key. mation Center (EVIC)” in Section 4 of this manual.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 During normal operation, after turning on the ignition switch, the Vehicle Security Light will turn on for three seconds for a bulb check. If the light remains on after the bulb check, it indicates that there is a problem with the electronics. In addition, if the light begins to flash after the bulb check, it indicates that someone used an invalid key to start the engine.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: The Sentry Key威 Immobilizer System is not compatible with some aftermarket remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection. authorized dealer or by using the Customer Key Programming procedure. This procedure consists of programming a blank key to the vehicle electronics. A blank key is one which has never been programmed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Insert the second valid key into the ignition switch. Turn the ignition switch to the ON position within 15 seconds. After ten seconds, a chime will sound. In addition, the Vehicle Security Light will begin to flash. Turn the ignition switch to the LOCK position and remove the second key. 17 Repeat this procedure to program up to eight keys. If you do not have a programmed Sentry Key威 contact your authorized dealer for details.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE VEHICLE SECURITY ALARM — IF EQUIPPED To Arm The System The Vehicle Security Alarm monitors the doors and trunk 1. Remove the keys from the ignition switch and get out for unauthorized entry and ignition switch for unauthoof the vehicle. rized operation. 2. Lock the door using either the power door lock switch If something triggers the alarm, the Vehicle Security (one door must be open) or the LOCK button on the Alarm will signal for about 18 minutes.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 NOTE: • The Vehicle Security Alarm remains armed during • During the 16 second arming period, if a door is trunk entry. Pressing the trunk button will not disarm opened or the ignition switch is turned ON, the the Vehicle Security Alarm. If someone enters the Vehicle Security Alarm will automatically disarm. vehicle through the trunk and opens any door, the alarm will sound.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Tamper Alert If the alarm was triggered, but the warning signals have • The front courtesy overhead console and door courtimed out, the park and taillights flash three times tesy lights do not turn on if the dimmer control is in (instead of the normal twice), and the horn will chirp the interior lights ON position (extreme top position).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 NOTE: To Unlock the Doors • The line of transmission must not be blocked with Press and release the UNLOCK button on the RKE metal objects. transmitter once to unlock the driver’s door, or twice to unlock all doors. The turn signal lights will flash to • Inserting the key into the ignition switch disables all acknowledge the unlock signal. The Illuminated Entry buttons on the RKE transmitter. system (if equipped) will also turn on.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • For vehicles not equipped with the EVIC, perform the Flash Lights With Lock The feature will cause the turn signal lights to flash when following procedure: the doors are locked or unlocked with the RKE transmit1. Press and hold the LOCK button on a programmed ter. This feature can be turned on or turned off. To change RKE transmitter for at least four seconds, but not longer the current setting, proceed as follows: than 10 seconds.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 equipped with EVIC. For details, refer to “Illuminated Approach,” under “Personal Settings (Customer3. Test the feature while outside of the vehicle, by Programmable Features), under “Electronic Vehicle Inforpressing the LOCK/UNLOCK buttons on the RKE transmation Center (EVIC)” in Section 4 of this manual. mitter with the ignition in the LOCK position, and the To Lock the Doors key removed. Press and release the LOCK button on the RKE transmit4.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • For vehicles not equipped with the EVIC, perform the To Unlatch the Trunk Press the TRUNK button on the RKE transmitter two following steps: times to unlatch the trunk. 1. Press the LOCK button on a programmed RKE transmitter for at least four seconds, but not longer than Using The Remote Open Window Feature — If 10 seconds. Then, press the PANIC button while still Equipped The RKE remotely lowers both driver and passenger holding the LOCK button.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 headlights and park lights will flash, the horn will pulse NOTE: Perchlorate Material — special handling may on and off, and the Illuminated Entry system (if apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate. equipped) will turn on. 1. With the RKE transmitter buttons facing down, use a The Panic Alarm will stay on for three minutes unless flat blade to pry the two halves of the RKE transmitter you turn it off by pressing the PANIC button a second apart.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Remove and replace the battery. Avoid touching the If your RKE transmitter fails to operate from a normal new battery with your fingers. Skin oils may cause distance, check for these two conditions. battery deterioration. If you touch a battery, clean it with 1. Weak battery in the RKE transmitter. The expected life rubbing alcohol. of battery is five years. 3. To assemble the RKE transmitter case, snap the two 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE How to Use Remote Start All of the following conditions must be met before the engine will remote start: • Shift lever in PARK • Doors closed • Hood closed • Trunk closed • Hazard switch off • Brake switch inactive (brake pedal not pressed) • Ignition key removed from ignition switch • Battery at an acceptable charge level, and • RKE PANIC button not pressed 27 WARNING! • Do not start or run an engine in a closed garage or confined area.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: To avoid unintentional shut downs, the system NOTE: • If an engine fault is present the vehicle will start and will disable the one-time press of the Remote Start button for two seconds after receiving a valid remote start then shut down 10 seconds later. request. • For security, power window operation is disabled To Exit Remote Start Mode and Drive the Vehicle when the vehicle is in the Remote Start mode.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE DOOR LOCKS 29 WARNING! Manual Door Locks To lock each door, push the door lock plunger on each door trim panel downward. To unlock each door, pull the door lock plunger on each door trim panel upward. Manual Lock Plunger • For personal security and safety in the event of an accident, lock the vehicle doors as you drive as well as when you park and leave the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CAUTION! An unlocked vehicle is an invitation to thieves. Always remove the key from the ignition and lock all of the doors when leaving the vehicle unattended. Power Door Locks A door lock switch is located on the driver and passenger door panel. Press this switch to lock or unlock the doors. Power Door Lock Switch Auto Door Lock — If Equipped When enabled, your door locks will lock automatically when the vehicle’s speed exceeds 15 mph (24 km/h).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 Auto Unlock On Exit Auto Unlock On Exit Programming The doors will unlock automatically on vehicles with The Automatic Unlock Doors on Exit feature can be power door locks if: enabled or disabled as follows: 1. The Automatic Unlock Doors on Exit feature is en- • For vehicles equipped with the Electronic Vehicle Information Center (EVIC), refer to “Personal Settings abled. (Customer-Programmable Features)” under “Elec2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Depress the power door unlock switch to unlock the doors. 4. A single chime will indicate the completion of the programming. 5. Repeat these steps if you want to return this feature to its previous setting. NOTE: Use the Automatic Unlock Doors on Exit feature in accordance with local laws. Child Protection Door Lock System (Rear Doors) The Child Protection Door Lock (Rear Doors) are located inside the rear edge of the door.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 WARNING! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged. 2 NOTE: For emergency exit with the system engaged, move the lock plunger up (UNLOCKED position), roll down the window, and open the door with the outside door handle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! To cancel the Auto-Down movement, operate the switch either in the up or down direction and release the switch. Never leave children in a vehicle, with the keys in the ignition switch. Occupants, particularly unattended children, can become entrapped by the windows while operating the power window switches. Such entrapment may result in serious injury or death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 Auto Window Up — If Equipped • Any impact due to rough road conditions may trigger Lift the window switch to the second detent, release, and the auto reverse function unexpectedly during autothe window will go up automatically. closure. If this happens, pull the switch lightly to the first detent and hold to close window manually. To cancel the Auto Up movement, operate the switch either in the up or down direction and release the switch.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Window Lockout Switch The window lockout switch on the driver’s door allows you to disable the window control on the other doors. To disable the window controls on the other doors, press the window LOCK button. To enable the window controls, press the window control button again. Window Lockout Switch Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE TRUNK LOCK AND RELEASE Use the Remote Keyless Entry (RKE) transmitter to open the trunk from outside the vehicle. From inside the vehicle the trunk lid can be released by pressing the TRUNK RELEASE button located on the instrument panel to the left of the steering wheel. NOTE: The shift lever must be in PARK for this button to operate. To unlatch the trunk lid from outside the vehicle, press and release the TRUNK button on the RKE transmitter two times.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Trunk Internal Emergency Release As a security measure, a Trunk Internal Emergency Release lever is built into the trunk latching mechanism. In the event of an individual being locked inside the trunk, the trunk can be simply opened by pulling on the glow-in-the-dark handle attached to the trunk latching mechanism.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 OCCUPANT RESTRAINTS • Knee bolsters/blockers for front seat occupants Some of the most important safety features in your • Front seat belts incorporate pretensioners to enhance vehicle are the restraint systems.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: The Advanced Front Airbags have a multistage Buckle up even though you are an excellent driver, even inflator design. This allows the airbag to have different on short trips. Someone on the road may be a poor driver rates of inflation based on severity and type of collision. and cause a collision that includes you. This can happen far away from home or on your own street. Please pay close attention to the information in this section.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE conditions. But in a collision, the belt will lock and reduce your risk of striking the inside of the vehicle or being thrown out. WARNING! • Be sure everyone in your vehicle is in a seat and using a seat belt properly. • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Wearing a seat belt incorrectly is dangerous.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2. The seat belt latch plate is above the back of the front seat, next to your arm. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to allow the belt to go around your lap. Pulling Out the Latch Plate 3.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 WARNING! • A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you as well. In a sudden stop, you could move too far forward, increasing the possibility of injury. Wear your seat belt snugly.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A belt that is worn under your arm is very dangerous. Your body could strike the inside surfaces of the vehicle in a collision, increasing head and neck injury. A belt worn under the arm can cause internal injuries. Ribs aren’t as strong as shoulder bones. Wear the belt over your shoulder so that your strongest bones will take the force in a collision. • A shoulder belt placed behind you will not protect you from injury during a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as possible and keep it snug. • A twisted belt can’t do its job as well. In a collision, it could even cut into you. Be sure the belt is straight. If you can’t straighten a belt in your vehicle, take it to your authorized dealer and have it fixed. 5.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belt Untwisting Procedure Use the following procedure to untwist a twisted lap/ shoulder belt. 1. Position the latch plate as close as possible to the anchor point. 2. At about 6 to 12 in (15 to 30 cm) above the latch plate, grasp and twist the belt webbing 180 degrees to create a fold that begins immediately above the latch plate. 3. Slide the latch plate upward over the folded webbing.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 Rear Seat Belts The shoulder belt anchorages of the rear three-point belts are nonadjustable for outboard and center rear passengers on sedans. The center belt is mounted to the rear shelf panel and exits through a bezel in the panel. How to Use the Automatic Locking Mode Automatic Locking Retractors (ALR) Mode — If Equipped In this mode, the shoulder belt is automatically prelocked. The belt will still retract to remove any slack in the shoulder belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seat Belt Pretensioners — If Equipped The seat belts for both front seating positions are equipped with pretensioning devices that are designed to remove slack from the seat belt in the event of a collision. These devices improve the performance of the seat belt by assuring that the belt is tight about the occupant early in a collision. Pretensioners work for all size occupants, including those in child restraints.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 When AHR’s deploy during a rear impact, the head restraint front half extends forward to minimize the gap between the back of the head and the AHR. This system is designed to help prevent or reduce the extent of injuries the driver and front passenger in certain types of rear end impacts. 2 NOTE: The Active Head Restraints (AHR) may or may not deploy in the event of a front or side impact.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CAUTION! 1. Grasp the deployed AHR from the rear seat. All occupants, including the driver, should not operate a vehicle or sit in a vehicle’s seat until the head restraints are placed in their proper positions in order to minimize the risk of neck injury in the event of an accident. NOTE: For more information on properly adjusting and positioning the head restraint, refer to Section 3 “Adjusting Active Head Restraints”.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 3. Pull down then rearward towards the rear of the vehicle then down to engage the locking mechanism.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. The AHR front soft foam and trim half should lock • For safety reasons, have the Active Head Restraints into the back decorative plastic half. checked by a qualified specialist at an authorized dealer. AHR In Reset Position NOTE: • If you have difficulties or problems resetting the head restraints, see an authorized dealer.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 BeltAlert威 will be reactivated if the driver’s seat belt is 3. Unbuckle and then re-buckle the driver’s seat belt at unbuckled for more than 10 seconds and the vehicle least three times within 10 seconds, ending with the seat belt buckled. speed is greater than 5 mph (8 km/h).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seat Belts and Pregnant Women We recommend that pregnant women use the seat belts throughout their pregnancy. Keeping the mother safe is the best way to keep the baby safe. Pregnant women should wear the lap part of the belt across the thighs and as snug across the hips as possible. Keep the belt low so that it does not come across the abdomen. That way the strong bones of the hips will take the force if there is a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 The Advanced Front Airbags have a multistage inflator design. This allows the airbag to have different rates of inflation that are based on the severity and type of collision. This vehicle may also be equipped with Supplemental Side Airbag Inflatable Curtains (SABIC) to protect the driver, front, and rear passengers sitting next to a window. If the vehicle is equipped with SABIC, they are located above the side windows.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Driver Front Airbag • • • • • • • Advanced Front Airbag Features The Advanced Front Airbag system has multistage driver Front Passenger Airbag and front passenger airbags.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Do not put anything on or around the airbag covers or attempt to open them manually. You may damage the airbags and you could be injured because the airbags may no longer be functional. The protective covers for the airbag cushions are designed to open only when the airbags are inflating. • Do not drill, cut or tamper with the knee bolster in any way.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE When the bag deploys, it opens the seam between the front and side of the seat’s trim cover. Each bag deploys independently, that is a left side impact deploys the left bag only and a right-side impact deploys only the right bag. Supplemental Side Airbag Inflatable Curtain (SABIC) — If Equipped SABIC airbags offer side-impact and vehicle rollover protection to front and rear seat outboard occupants in addition to that provided by the body structure.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 The system includes sensors adjacent to both front and protection for the driver and front passenger. Side airbags rear seat occupants that are calibrated to deploy the also work with seat belts to improve occupant protection. SABIC airbags during impacts that require airbag occuKnee Impact Bolsters pant protection.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Children that are not big enough to wear the vehicle seat belt properly (see section on Child Restraints) should be secured in the rear seat in child restraints or beltpositioning booster seats. Older children who do not use child restraints or belt-positioning booster seats should ride properly buckled up in the rear seat. Never allow children to slide the shoulder belt behind them or under their arm. 3.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly. In some collisions, the airbags won’t deploy at all. Always wear your seat belts even though you have airbags. • Being too close to the steering wheel or instrument panel during front airbag deployment could cause serious injury, including death. Airbags need room to inflate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The Advanced Front Airbags will not deploy in all frontal collisions, including some that may produce substantial vehicle damage — for example, some pole collisions, truck underrides, and angle offset collisions. On the other hand, depending on the type and location of impact, Advanced Front Airbags may deploy in crashes with little vehicle front-end damage but that produce a severe initial deceleration.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE It also includes diagnostics that will illuminate the instrument cluster Airbag Warning Light if a malfunction is noted. The diagnostics also record the nature of the malfunction. WARNING! Ignoring the Airbag Warning Light in your instrument panel could mean you won’t have the airbags to protect you in a collision. If the light does not come on, stays on after you start the vehicle, or if it comes on as you drive, have the airbag system checked right away.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Supplemental Seat Side Airbag Inflator Units — If force, that it could injure you if you are not seated properly, or if items are positioned in the area where the Equipped The Side Impact (SRS) Seat-Mounted Side Airbags are side airbag inflates. This especially applies to children. designed to activate only in certain side collisions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 where the side curtain airbag inflates. This especially event the ORC will determine whether to have the applies to children. The side curtain airbag is only about Enhanced Accident Response System to perform the following functions: 3-1/2 in (9 cm) thick when it is inflated. Because airbag sensors estimate deceleration over time, • Cut off fuel to the engine.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If you do have a collision, which deploys the airbags, any or all of the following may occur: throat irritation, move to fresh air. If the irritation continues, see your doctor. If these particles settle on your clothing, follow the garment manufacturer’s instructions for cleaning. • The nylon airbag material may sometimes cause abrasions and/or skin reddening to the driver and front passenger as the airbags deploy and unfold.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Maintaining Your Airbag System 67 WARNING! (Continued) WARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. You could be injured if the airbag system is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the steering wheel hub trim cover or the upper right side of the instrument panel.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag Warning Light You will want to have the airbags ready to inflate for your protection in a collision. While the airbag system is designed to be maintenance free, if any of the following occurs, have an authorized dealer service the system immediately. located on the inside of the fuse block cover for the proper airbag fuses. See your authorized dealer if the fuse is good.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 2. Under certain circumstances, EDR data may not be accessing the electronic data stored, unless ordered to download data by a court with legal jurisdiction (i.e., recorded (e.g., loss of battery power). pursuant to a warrant). A copy of the data will be In conjunction with other data gathered during a comprovided to the custodial entity upon request.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE United States and all Canadian provinces require that small children ride in proper restraint systems. This is the law, and you can be prosecuted for ignoring it. 3. Requested by police under a legal warrant. 4. Otherwise required by law. Data parameters that are recorded: Children 12 years and younger should ride properly • Diagnostic trouble code(s) and warning light status for buckled up in a rear seat, if available.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt. Always check the child seat owner’s manual to ensure you have the correct seat for your child. Use the restraint that is correct for your child. Infants and Small Children 71 vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE vehicle by the lap/shoulder belt or the LATCH child restraint anchorage system. Refer to “LATCH — Child Seat Anchorage System (Lower Anchors and Tether for CHildren)” in this section. The belt-positioning booster seat is for children weighing more than 40 lbs (18 kg), but who are still too small to fit the vehicle’s seat belts properly.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Here are some tips on getting the most out of your child restraints: 73 • Carefully follow the instructions that come with the restraint. If you install the restraint improperly, it may not work when you need it. • Children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to • All passenger seating positions contain automatic bend over the front of the seat when their back is locking retractors.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • If the belt still can’t be tightened, or if pulling and pushing on the restraint loosens the belt, disconnect the latch plate from the buckle, turn the latch plate around, and insert the latch plate into the buckle again. If you still can’t make the child restraint secure, try a different seating position. NOTE: For additional information, refer to www.seatcheck.org or call 1–866–SEATCHECK.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 rear seating positions, you can use the LATCH anchors or the vehicle’s seat belt for the outboard position, but you must use the vehicle’s seat belt at the center position. If your child restraints are not LATCH-compatible, you can only install the child restraints using the vehicle’s seat belts. For typical installation instructions, refer to “Installing the LATCH-Compatible Child Restraint System”.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE have tether straps, and you are urged to take advantage Installing the LATCH-Compatible Child Restraint of all of the available attachments provided with your System We urge you to carefully follow the directions of the child restraint in any vehicle. manufacturer when installing your child restraint. Not all NOTE: When using the LATCH attaching system to child restraint systems will be installed as described here.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77 window. These tether strap anchorages are under a most direct path between the anchor and the child restraint. Finally, tighten all three straps as you push the plastic cover with this symbol on it. child restraint rearward and downward into the seat, Many, but not all restraint systems will be equipped with removing slack in the straps according to the child separate straps on each side, with each having a hook or restraint manufacturer’s instructions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE the child restraint belt path and then buckle it. This should stow the seat belt out of the reach of an inquisitive child. Remind all children in the vehicle that the seat belts are not toys and should not be played with, and never leave your child unattended in the vehicle. WARNING! Improper installation of a child restraint to the LATCH anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE route the tether strap under the head restraint and between the two posts. If not possible, lower the head restraint and pass the tether strap around the outboard side of the head restraint. 79 Installing Child Restraints Using the Vehicle Seat Belts The passenger seat belts are equipped with Automatic Locking Retractors (ALRs), which are designed to keep the lap portion tight around the child restraint. 3.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE In the rear seat, you may have trouble tightening the lap/shoulder belt on the child restraint because the buckle or latch plate is too close to the belt path opening on the restraint. Disconnect the latch plate from the buckle and twist the short buckle-end belt several times to shorten it. Insert the latch plate into the buckle with the release button facing out.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Transporting Pets Airbags deploying in the front seat could harm your pet. An unrestrained pet will be thrown about and possibly injured, or injure a passenger during panic braking or in a collision. 81 While cruising, brief full-throttle acceleration within the limits of local traffic laws, contributes to a good break-in. Wide-open throttle acceleration in low gear can be detrimental and should be avoided.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE SAFETY TIPS Exhaust Gas Transporting Passengers NEVER TRANSPORT PASSENGERS IN THE CARGO AREA. WARNING! • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 83 If you are required to drive with the trunk/liftgate open, Safety Checks You Should Make Inside the make sure that all windows are closed and the climate Vehicle control BLOWER switch is set at high speed. DO NOT Seat Belts use the recirculation mode. Inspect the belt system periodically, checking for cuts, The best protection against carbon monoxide entry into frays, and loose parts.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Defroster Check operation by selecting the defrost mode and place the blower control on high speed. You should be able to feel the air directed against the windshield. See your authorized dealer for service if your defroster is inoperable. Periodic Safety Checks You Should Make Outside the Vehicle Lights Have someone observe the operation of exterior lights while you work the controls. Check turn signal and high beam indicator lights on the instrument panel.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 䡵 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 ▫ Manual Front Seat Adjustment . . . . . . . . . . . . 94 ▫ Inside Day/Night Mirror . . . . . . . . . . . . . . . . 89 ▫ Driver Seat Manual Height Adjuster — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 95 ▫ Automatic Dimming Mirror — If Equipped . . . 90 ▫ Power Mirrors . . . . . . . . . . . . . . . . . . . . . . . 90 ▫ Adjusting Sideview Mirrors . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Folding Rear Seat . . . . . . . . . . . . . . . . . . . . 103 ▫ Daytime Running Lights — If Equipped . . . . 110 ▫ Folding Rear Seat Center Armrest . . . . . . . . 104 ▫ Lights On Reminder . . . . . . . . . . . . . . . . . . 110 䡵 To Open And Close The Hood . . . . . . . . . . . . 104 ▫ Instrument Panel Dimmer . . . . . . . . . . . . . . 110 䡵 Lights ▫ Map/Reading/Interior Lights . . . . . . . . . . . . 111 . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ To Set a Desired Speed . . . . . . . . . . . . . . . . 118 ▫ To Deactivate . . . . . . . . . . . . . . . . . . . . . . . 118 ▫ To Resume Speed . . . . . . . . . . . . . . . . . . . . 118 ▫ To Vary The Speed Setting . . . . . . . . . . . . . . 119 ▫ To Accelerate For Passing . . . . . . . . . . . . . . 120 䡵 Garage Door Opener — If Equipped . . . . . . . . 120 ▫ Programming HomeLink威 . . . . . . . . . . . . . . 121 ▫ Gate Operator/Canadian Programming . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 䡵 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134 ▫ Dual Storage Bins . . . . . . . . . . . . . . . . . . . . 136 ▫ Driver’s Side Sunglass Holder — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . 134 ▫ Video Console — If Equipped . . . . . . . . . . . 138 ▫ Cargo Area . . . . . . . . . . . . . . . . . . . . . . . . 134 䡵 Console Features . . . . . . . . . . . . . . . . . . . . . . 136 䡵 Rear Window Features . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 MIRRORS Inside Day/Night Mirror A two-point pivot system allows for horizontal and vertical mirror adjustment. Adjust the mirror to center on the view through the rear window. 3 Headlight glare can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle). The mirror should be adjusted while set in the day position (toward the windshield).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Dimming Mirror — If Equipped This mirror will automatically adjust for headlight glare from vehicles behind you. Push in the button on the face of the mirror to activate the dimming feature. CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91 3 Power Mirror Switch After selecting a mirror, move the knob in the same direction you want the mirror to move. When finished, return the knob to the center (Off) position to guard against accidentally moving a mirror position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Adjusting Sideview Mirrors Outside Mirror — Driver Side Adjust the outside mirror to center on the adjacent lane of traffic, with a slight overlap of the view obtained on the inside mirror. Outside Mirror — Passenger Side Adjust the convex outside mirror so you can just see the side of your vehicle in the part of the mirror closest to the vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Illuminated Vanity Mirrors — If Equipped An illuminated vanity mirror is on each sun visor. To use the mirror, lower the sun visor and rotate the mirror cover upward. The lights will turn on automatically. Closing the mirror cover turns off the lights. Illuminated Vanity Mirror 93 uconnect™ phone — IF EQUIPPED Refer to “uconnect™ phone” in the uconnect™ User Manual located on the DVD for further details.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE SEATS the position desired. Then, using body pressure, move Seats are a primary part of the Occupant Restraint System forward and rearward on the seat to be sure that the seat of the vehicle. They need to be used properly for safe adjusters have latched. operation of the vehicle. WARNING! • DO NOT allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 WARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust the seat only while the vehicle is parked. Driver Seat Manual Height Adjuster — If Equipped A lever style height adjustment feature enhances comfort for petite as well as tall drivers.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Reclining Bucket Seats The recliner control is on the side of the seat. To recline, lean forward slightly before lifting the lever, then lean back to the desired position and release the lever. Lean forward and lift the lever to return the seatback to its normal position. Seatback Adjustment WARNING! • Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Lumbar Support — If Equipped This feature allows you to increase or decrease the amount of lumbar support. The control lever is located on the outboard side of the driver’s seatback. Turn the control lever downward to increase and upward to decrease the desired amount of lumbar support. Power Seats — If Equipped The power seat switches are on the outboard side of the seat near the floor.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust the seat only while the vehicle is parked. • Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or even fatally injured.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To raise the head restraint, pull upward on the head restraint (on some models, you may need to press the push button). To lower the head restraint, press the push button, located at the base of the head restraint, and push downward on the head restraint. 99 For comfort the Active Head Restraints can be tilted forward and backward. To tilt the head restraint closer to the back of your head, pull outward on the bottom of the head restraint.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • In the event of deployment of an Active Head Restraint, refer to “Resetting Active Head Restraints (AHR)” under “Occupant Restraints” in Section 2. WARNING! Active Head Restraint (Tilted) NOTE: • The head restraints should only be removed by qualified technicians, for service purposes only. If either of the head restraints require removal, see your authorized dealer.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Heated Seats — If Equipped This feature heats leather or cloth front driver and passenger seats. The switches for the heated seats are located in the center console above the climate controls. After turning the ignition ON, you can choose from High, Low, or Off heat settings. Amber indicator lights in each switch indicate the level of heat in use. Two indicator lights will illuminate for High, one for Low and none for Off.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE The hard seatback features a work surface and a molded Fold-Flat Passenger Seatback The recline handle on the front passenger seat also rim for retaining items stored on the seatback panel. releases the seatback to fold forward.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Folding Rear Seat To provide additional storage area, the rear seatback can be folded forward. Pull on the loops shown in the picture to fold down either or both seatbacks. When returning the rear seatback to the upright position, be sure the seatback is latched. Folding Rear Seats 103 WARNING! The rear cargo area of the vehicle (with the rear seatbacks in the locked-up or folded down position) should not be used as a play area by children.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Folding Rear Seat Center Armrest TO OPEN AND CLOSE THE HOOD The rear seat is equipped with a folding armrest with To open the hood, two latches must be released. cupholders. 1. Pull the hood release lever located under the left side of the instrument panel.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 2. Then lift the secondary latch located under the front edge of the hood, near the center and raise the hood. 3 Hood Prop Rod Hole Location Hood Safety Catch Use the hood prop rod to secure the hood in the open position. Place the upper end of the prop rod in the hole on the left underside of the hood. NOTE: Before closing the hood, make sure to stow the prop rod in its proper location.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! To prevent possible damage, do not slam the hood to close it. Use a firm downward push at the center of the hood to ensure that both latches engage. passing light, fog lights, instrument panel light dimming and turn signals. The multifunction lever is located on the left side of the steering column. WARNING! If the hood is not fully latched it could fly up when the vehicle is moving and block your forward vision. You could have a collision.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Headlights and Parking Lights Turn the end of the multifunction lever to the first detent for parking light operation. Turn to the second detent for headlight operation. 107 Automatic Headlights — If Equipped Turning the end of the multifunction lever to the third detent (AUTO), will activate the automatic headlight system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE With the engine running and the multifunction lever in the AUTO position, the headlights will turn on and turn off based on the surrounding light levels. Headlight Time Delay There is also a feature that delays turning off the vehicle lights for 30, 60 or 90 seconds after the ignition switch is turned OFF. To activate the headlight delay, the multifunction lever must be rotated to the off position after the ignition switch is turned OFF.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 Lane Change Assist Fog Lights — If Equipped Tap the lever up or down once, without moving beyond The front fog light switch is on the multifunction the detent, and the turn signal (right or left) will flash lever. To activate the front fog lights, turn on the three times then automatically turn off. parking lights or the low beam headlights and pull out the end of the multifunction lever.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The front fog lights will only operate with the Lights On Reminder headlights on low beam. Selecting high beam headlights If the headlights or parking lights are on after the ignition is turned OFF, a chime will sound to alert the driver will turn off the front fog lights. when the driver’s door is opened.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 Rotate the center portion upward to the last detent to aimed at a specific spot, if desired. The lights will remain on until the switch is pressed a second time, so be sure they turn on the interior lighting. have been turned off before leaving the vehicle. They will not turn off automatically. Interior lighting also comes on when a door is opened or the dimmer control is turned fully upward, past the second detent.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE There is a second light located midway back in the headliner. To protect the battery, the interior lights will turn off automatically 10 minutes after the ignition switch is moved to the LOCK position. This will occur if the interior lights were switched on manually or are on because a door is open. To restore interior light operation, either turn the ignition switch ON or cycle the light switch.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 CAUTION! • Turn the windshield wipers off when driving through an automatic car wash. Damage to the windshield wipers may result if the wiper control is left in any position other than off. • Always remove any buildup of snow that prevents the windshield wiper blades from returning to the off position. If the windshield wiper control is turned off and the blades cannot return to the off position, damage to the wiper motor may occur.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE regulate the wipe interval from a minimum of one cycle Mist Feature every second to a maximum of approximately 18 seconds Push down on the wiper control lever to activate a single wipe to clear the windshield of road mist or spray from between cycles. a passing vehicle. As long as the lever is held down, the For vehicles equipped with the Speed Sensitive Intermitwipers will continue to operate. tent Wiper System, the wiper delay times depend on vehicle speed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Headlights With Wipers Feature (Available With Automatic Headlights Only) When this feature is active, the headlights will turn on approximately 10 seconds after the wipers are turned on if the multifunction lever (on the left side of the steering column) is placed in the AUTO position. In addition, the headlights will turn off when the wipers are turned off if they were turned on by this feature.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE TILT/TELESCOPING STEERING COLUMN This feature allows you to tilt the steering column upward or downward. It also allows you to lengthen or shorten the steering column. The tilt/telescoping control handle is located below the steering wheel at the end of the steering column. To unlock the steering column, pull the control handle outward. To tilt the steering column, move the steering wheel upward or downward as desired.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 NOTE: In order to ensure proper operation, the Electronic Speed Control System has been designed to shut down if multiple Speed Control functions are operated simultaneously. If this occurs, the Electronic Speed Control System can be reactivated by pushing the Electronic The Electronic Speed Control lever is located on the right Speed Control ON/OFF button and resetting the desired side of the steering wheel. vehicle set speed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Leaving the Electronic Speed Control on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the system off when you are not using it.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Vary the Speed Setting When the Electronic Speed Control is set, you can increase speed by pushing up and holding the RESUME ACCEL lever. If the lever is continually held in the RESUME ACCEL position, the set speed will continue to increase in 5 mph (10 km/h) increments until the lever is released. Release the lever when the desired speed is reached and the new set speed will be established.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE The HomeLink威 buttons that are located in the headliner To Accelerate for Passing Press the accelerator as you would normally. When the or sun visor designate the three different HomeLink威 pedal is released, the vehicle will return to the set speed. channels. Using Electronic Speed Control On Hills NOTE: The Electronic Speed Control system maintains speed up and down hills. A slight speed change on moderate hills is normal.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Your motorized door or gate will open and close while you are training the universal transceiver. Do not train the transceiver if people, pets or other objects are in the path of the door or gate. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by Federal safety standards. This includes most garage door opener models manufactured after 1982.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Place the handheld transmitter 1 to 3 in (3 to 8 cm) away • After training a HomeLink威 channel, if the garage from the HomeLink威 button you wish to program while door does not operate with HomeLink威 and the gakeeping the indicator light in view. rage door opener was manufactured after 1995, the garage door opener may have a rolling code. If so, 3.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 This can usually be found where the hanging antenna 6. Firmly press and release the LEARN or TRAINING wire is attached to the garage door opener motor. It is button. The name and color of the button may vary by NOT the button normally used to open and close the manufacturer. door. NOTE: You have 30 seconds in which to initiate the next step after the LEARN button has been pressed. 7.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Using HomeLink威 To operate, press and release the programmed HomeLink威 button. Activation will now occur for the trained device (i.e., garage door opener, gate operator, security system, entry door lock, home/office lighting, etc.,). The handheld transmitter of the device may also be used at any time.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 successfully accepted the frequency signal. The indica- Troubleshooting Tips tor light will flash slowly and then rapidly when fully If you are having trouble programming HomeLink威, here are some of the most common solutions: trained. If you unplugged the device for training, plug it back in • Replace the battery in the original transmitter. at this time. • Press the LEARN button on the Garage Door Opener to complete the training for a Rolling Code.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE General Information POWER SUNROOF — IF EQUIPPED This device complies with FCC rules Part 15 and Industry The sunroof controls are mounted between the dome/ Canada RSS-210. Operation is subject to the following reading lights. two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference that may be received including interference that may cause undesired operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Never leave children in a vehicle with the key in the ignition switch. Occupants, particularly unattended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death. • In an accident, there is greater risk of being thrown from a vehicle with an open sunroof. You could also be seriously injured or killed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The sunshade cannot be closed if the sunroof is Venting Sunroof — Express Press and release the “Vent” button, the sunroof will open. open to the vent position. This is called “Express Vent”. Wind Buffeting Closing Sunroof — Express Wind buffeting can be described as the perception of Press the switch forward and release, the sunroof will pressure on the ears or a helicopter-type sound in the close automatically from any position. The sunroof will ears.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Ignition Off Operation For vehicles not equipped with the Electronic Vehicle Information Center (EVIC), the power sunroof switch will remain active for 45 seconds after the ignition switch is turned OFF. Opening either front door will cancel this feature. The instrument panel power outlet, located below the climate control knobs, has power available only when the ignition is ON. This power outlet will also operate a conventional cigar lighter unit.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE The center console power outlet is powered directly from NOTE: the battery (power available at all times). Items plugged • To ensure proper operation, a MOPAR威 knob and element must be used. into this power outlet may discharge the battery and/or prevent the engine from starting. • Do not exceed the maximum power of 120 Watts (10 Amps) at 12 Volts.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting. • Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.) will degrade the battery even more quickly.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! For vehicles equipped with the heated and cooled cupholder, locate the cup holder ash receiver in the forward cupholder. When the unit is on and the LED is Red, the cupholder is being heated. When the LED is Blue, the cupholder is being cooled. The optional ash receiver also comes with a cigar lighter.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! When using the cupholder in the “Heat” position, avoid contact with the heated portion of the cupholder in order to reduce the possibility of burns. Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injuries, medication, alcohol use, exhaustion or other physical condition must exercise particular care in order to prevent serious burn injury.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! If containers of hot liquid are placed in the bottle holder, they can spill when the door is closed, burning the occupants. Be careful when closing the doors to avoid injury. STORAGE Driver’s Side Sunglass Holder — If Equipped An integrated sunglass holder is located in the headliner above the sun visor. To access the sunglass holder, lower the sun visor.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE When the seatback is folded to the upright position, make sure it is latched by strongly pulling on the top of the seatback above the seat strap. WARNING! • Be certain that the seatback is securely locked into position. If the seatback in not securely locked into position, the seat will not provide the proper stability for child seats and/or passengers. An improperly latched seat could cause serious injury.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Do not pile luggage or cargo higher than the top of the seatback. This could impair visibility or become a dangerous projectile in a sudden stop or collision. CONSOLE FEATURES The center console armrest slides forward from design position to provide added user comfort. Two cupholders, each of which can accommodate large beverage containers. A one piece cupholder insert for both cavities can easily be removed for cleaning.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 The left latch opens to the top storage area. The lower bin can be accessed directly, without first exposing the upper bin, by operating the right latch with the armrest down. The first storage bin can be used to hold smaller items. The lower storage bin includes a molded-in coin holder, room for CD’s, DVD’s, and a power outlet that allows a cellular phone to recharge while concealed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Video Console — If Equipped The optional Video Entertainment System (VES)™ includes the following components: • The screen for a rear seat DVD player is stored under the armrest. • Remote Control • Audio/Video RCA Jacks Video Console Refer to, “Video Entertainment System — If Equipped,” in Section 4 of this manual, for further information.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE REAR WINDOW FEATURES Rear Window Defroster The rear window defroster button is located on the climate control (Mode) knob. Press this button to turn on the rear window defroster and the heated outside mirrors (if equipped). An indicator in the button will illuminate when the rear window defroster is on. The rear window defroster automatically turns off after approximately 10 minutes. For an additional five minutes of operation, press the button a second time.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 Instrument Panel Features . . . . . . . . . . . . . . . 144 䡵 Instrument Cluster . . . . . . . . . . . . . . . . . . . . 145 䡵 Instrument Cluster Descriptions . . . . . . . . . . . 146 䡵 Electronic Vehicle Information Center (EVIC) – If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 159 ▫ Electronic Vehicle Information Center (EVIC) Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . 161 ▫ Oil Change Required . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL ▫ List Button (Disc Mode For MP3/WMA Play) . . . . . . . . . 183 ▫ Operation Instructions — CD Mode For CD And MP3 Audio Play . . . . . . . . . . . . . . . . . 191 ▫ Info Button (Disc Mode For MP3/WMA Play) . . . . . . . . . 183 ▫ Notes On Playing MP3 Files . . . . . . . . . . . . 193 䡵 Sales Code (RER/REN) — AM/FM/CD/DVD Radio – If Equipped . . . . . . . . . . . . . . . . . . . . 186 ▫ Operating Instructions — Voice Recognition System (VR) — If Equipped . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 䡵 uconnect™ studios (Satellite Radio) — If Equipped (REN/REQ/RER/RES Radios Only) . . . . . . . . . . . . . . . . . . . . . . . . . 209 ▫ System Activation . . . . . . . . . . . . . . . . . . . . 209 ▫ Electronic Serial Number/Sirius Identification Number (ESN/SID) . . . . . . . . . 209 ▫ Selecting uconnect™ studios (Satellite) Mode . . 210 143 䡵 Remote Sound System Controls — If Equipped . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT PANEL FEATURES 1 2 3 4 5 — Air Outlet — Side Window Demister Outlet — Instrument Cluster — Ignition Switch — Analog Clock 6 — Radio 7 — Passenger Airbag 8 — Glove Compartment 9 — Heated Seat Switch – If Equipped 10 — Hazard Switch 11 — Storage Compartment 12 — Climate Control 13 — Trunk Release Button
UNDERSTANDING YOUR INSTRUMENT PANEL 145 INSTRUMENT CLUSTER 4
UNDERSTANDING YOUR INSTRUMENT PANEL removes this heat. You can also turn the Temperature control to maximum heat, the Mode control to Floor and 1. Temperature Gauge the Fan control to High. This allows the heater core to act The temperature gauge shows engine coolant temperaas a supplement to the radiator and aids in removing heat ture. Any reading below the red area of the gauge shows from the engine cooling system. that the engine cooling system is operating properly.
UNDERSTANDING YOUR INSTRUMENT PANEL 147 If jump starting is required, refer to “Jump Starting 5. Low Fuel Light When the fuel level drops to approximately 2.0 gal- Procedures” in section 6 of this manual. lons (7.6 Liters), the fuel symbol will light and a 7. Airbag Warning Light single chime will sound. The light comes on and remains on for six to NOTE: This light will remain on until a minimum of eight seconds as a bulb check when the ignition switch is first turned ON.
UNDERSTANDING YOUR INSTRUMENT PANEL 11. Brake Warning Light 9. Oil Pressure Warning Light This light indicates low engine oil pressure. The This light monitors various brake functions, including brake fluid level and parking brake light will come on and remain on when the application. If the brake light turns on, it may ignition switch is turned from the OFF to the ON indicate that the parking brake is applied, that position, and the light will turn off after the engine is started.
UNDERSTANDING YOUR INSTRUMENT PANEL 149 If brake failure is indicated, immediate repair is neces- unless the parking brake is applied or a brake fault is sary. detected. If the light does not illuminate, have the light inspected by an authorized dealer. WARNING! Driving a vehicle with the brake light on is dangerous. Part of the brake system may have failed. It will take longer to stop the vehicle. You could have an accident. Have the vehicle checked immediately.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: You must apply the brakes before shifting from The two trip odometers show individual trip mileage. To switch from odometer to trip odometers, press and PARK. release the Trip Odometer button. To reset a trip odom14. Odometer/Trip Odometer eter, display the desired trip odometer to be reset then The odometer shows the total distance the vehicle has push and hold the button until the display resets (apbeen driven. U.S.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: If the instrument cluster is equipped with the optional Electronic Vehicle Information Center (EVIC), then warnings such as ”Low Tire,” “Door Ajar” and “Trunk Ajar” will display in the EVIC. (Refer to “Electronic Vehicle Information Center (EVIC)” in this section for specific messages). LoW TirE When the appropriate condition exists, the odometer display will toggle between LoW and TirE for three cycles.
UNDERSTANDING YOUR INSTRUMENT PANEL 2. Fully depress the accelerator pedal slowly 3 times CHAngE OIL Your vehicle is equipped with an engine oil change within 10 seconds. indicator system. The “CHAngE OIL” message will flash 3. Turn the ignition switch to the LOCK position. in the instrument cluster odometer for approximately 12 seconds after a single chime has sounded to indicate NOTE: If the indicator message illuminates when you the next scheduled oil change interval.
UNDERSTANDING YOUR INSTRUMENT PANEL 153 To reset the trip odometer, first display the trip mileage that you want to reset, “Trip A” or “Trip B.” Then push Single Trip Odometer and hold the button (approximately 2 seconds) until the Press and release this button to change the display from display resets to 0 miles (km). The odometer must be in odometer to trip odometer. The word “Trip” displays to Trip Mode to reset the trip odometer. show that the odometer is in Trip Mode.
UNDERSTANDING YOUR INSTRUMENT PANEL The light will come on when the ignition switch is first 21. Front Fog Light Indicator — If Equipped turned on and remain on approximately 15 seconds as a This indicator will illuminate when the front fog bulb check. This is normal. If the light does not come on lights are on. during starting, have the system checked by an autho22. Vehicle Security Light — If Equipped rized dealer. This light will flash rapidly for approximately 18.
UNDERSTANDING YOUR INSTRUMENT PANEL 155 the conventional brake system will continue to operate malfunction has been detected in the ESC system. If this normally provided that the BRAKE warning light is not light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometers) at on.
UNDERSTANDING YOUR INSTRUMENT PANEL 25. Tire Pressure Monitoring Telltale Light Each tire, including the spare (if provided), should be checked monthly, when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.
UNDERSTANDING YOUR INSTRUMENT PANEL 157 TPMS malfunction telltale after replacing one or more 26. Malfunction Indicator Light (MIL) tires or wheels on your vehicle, to ensure that the The Malfunction Indicator Light (MIL) is part of replacement or alternate tires and wheels allow the TPMS an onboard diagnostic system called OBD that to continue to function properly. monitors emissions, engine, and automatic transaxle control systems.
UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! Prolonged driving with the MIL on could cause damage to the engine control system. It also could affect fuel economy and drivability. If the MIL is flashing, severe catalytic converter damage and power loss will soon occur. Immediate service is required. WARNING! A malfunctioning catalytic converter, as referenced above, can reach higher temperatures than in normal operating conditions.
UNDERSTANDING YOUR INSTRUMENT PANEL WARNING! In some circumstances a Transmission Temperature Indicator, under continued operation, could cause the fluid to boil over, come in contact with hot engine or exhaust components and cause a fire. ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) – IF EQUIPPED The Electronic Vehicle Information Center (EVIC) features a driver-interactive display that is located in the instrument cluster. 4 28.
UNDERSTANDING YOUR INSTRUMENT PANEL The EVIC consists of the following: • System status • Vehicle information warning message displays • Personal Settings (Customer-Programmable Features) • Compass heading display (N, S, E, W, NE, NW, SE, SW) The system allows the driver to select information by pressing the following buttons on the instrument panel switch bank located below the climate controls: Press and release the MENU button to advance the display to Trip Functions or Personal settings or to ret
UNDERSTANDING YOUR INSTRUMENT PANEL RESET Button 161 Press and release the RESET button to accept a • Right Rear Turn Signal Light Out (with a single chime) selection. The RESET button also resets various • RKE (Remote Keyless Entry) Battery Low (with a Trip Functions.
UNDERSTANDING YOUR INSTRUMENT PANEL Oil Change Required Your vehicle is equipped with an engine oil change indicator system. The Oil Change Required message will flash in the EVIC display for approximately five seconds after a single chime has sounded to indicate the next scheduled oil change interval. The engine oil change indicator system is duty cycle based, which means the engine oil change interval may fluctuate dependent upon your personal driving style. 2.
UNDERSTANDING YOUR INSTRUMENT PANEL 163 Press and release the STEP button to advance the display • Distance To Empty (DTE) through the Trip Functions. Shows the estimated distance that can be traveled with the fuel remaining in the tank. This estimated distance is The Trip Functions mode displays the following informadetermined by a weighted average of the instantaneous tion: and average fuel economy, according to the current fuel • ECO (Fuel Saver Indicator) — If Equipped tank level.
UNDERSTANDING YOUR INSTRUMENT PANEL • Elapsed Time Compass Display The compass heading indicates the direction Shows the total elapsed time of travel since the last reset. the vehicle is facing. Press and release the Elapsed time will increment when the ignition switch is compass button to display one of eight comin the ON or START position. COM- pass heading and the outside temperature.
UNDERSTANDING YOUR INSTRUMENT PANEL 165 NOTE: A good calibration requires a level surface and 4. Press and release the RESET button and the “CAL” an environment free from large metallic objects such as indicator will quit flashing. buildings, bridges, underground cables, railroad tracks, 5. Drive the vehicle slowly (under 5 mph / 8 km/h), etc.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Magnetic and battery powered devices, (such as cell phones, iPod’s, radar detectors, PDA’s and laptops) should be kept away from the top of the instrument panel. This is where the compass module is located and such devices may interfere and cause false compass readings. 1. Turn the ignition switch to the ON position. Leave the shift lever in PARK. 2. Press and release the MENU button until “Personal Settings” displays in the EVIC. 3.
UNDERSTANDING YOUR INSTRUMENT PANEL Personal Settings (Customer-Programmable Features) Personal settings allows the driver to set and recall features when the automatic transaxle is in PARK. 167 Auto Unlock on Exit When ON is selected and the transaxle is in the PARK or NEUTRAL position, all doors will unlock when the driver’s door is opened. To make your selection, press and hold the RESET button until ON or OFF appears.
UNDERSTANDING YOUR INSTRUMENT PANEL Sound Horn with Lock When ON is selected, a short horn sound will occur when the RKE transmitter LOCK button is pressed. This feature may be selected with or without the Flash Lights with Lock feature. To make your selection, press and release the RESET button until ON or OFF appears. Flash Lights with Lock When ON is selected, the front and rear turn signals will flash when the doors are locked or unlocked with the RKE transmitter.
UNDERSTANDING YOUR INSTRUMENT PANEL power outlets will remain active for up to 10 minutes after the ignition switch is turned to the LOCK position. Opening a vehicle door will cancel this feature. To make your selection, press and hold the RESET button until Off, 45 sec., 5 min., or 10 min. appears. 169 Display Units in English or Metric The EVIC and odometer can be changed between English and Metric units of measure.
UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE REQ — AM/FM STEREO RADIO AND 6–DISC CD/DVD CHANGER (MP3/WMA AUX JACK) Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. NOTE: The radio sales code is located on the lower right Power Switch/Volume Control (Rotary) side of the radio faceplate. Push the ON/VOLUME control knob to turn on the radio. Press the ON/VOLUME control knob a second time to turn off the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL SEEK Buttons Press and release the SEEK buttons to search for the next listenable station in AM/FM mode. Press the right switch to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations without stopping until you release it.
UNDERSTANDING YOUR INSTRUMENT PANEL The clock can also be set by pressing the SETUP button TIME Button Press the TIME button to alternate locations of the time and selecting the “SET HOME CLOCK” entry. Once in this display follow the above procedure, starting at and frequency display. step 2. Clock Setting Procedure INFO Button 1. Press and hold the TIME button until the hours blink. Press the INFO button for an RDS station (one with call 2.
UNDERSTANDING YOUR INSTRUMENT PANEL Setting the Tone, Balance, and Fade Push the rotary TUNE/SCROLL control knob and BASS will display. Turn the TUNE/SCROLL control knob to the right or left to increase or decrease the bass tones. 173 Push the rotary TUNE/SCROLL control knob a fifth time and FADE will display. Turn the TUNE/SCROLL control knob to the left or right to adjust the sound level between the front and rear speakers.
UNDERSTANDING YOUR INSTRUMENT PANEL Toggle the MUSIC TYPE button to select the following format types: Program Type No program type or undefined Adult Hits Classical Classic Rock College Country Foreign Language Information Jazz News Nostalgia Oldies 16-Digit Character Display None Adlt Hit Classicl Cls Rock College Country Language Inform Jazz News Nostalga Oldies Program Type Personality Public Rhythm and Blues Religious Music Religious Talk Rock Soft Soft Rock Soft Rhythm and Blues Sports Talk To
UNDERSTANDING YOUR INSTRUMENT PANEL By pressing the SEEK button when the Music Type icon is displayed, the radio will be tuned to the next frequency station with the same selected Music Type name. The Music Type function only operates when in the FM mode. If a preset button is activated while in the Music Type (Program Type) mode, the Music Type mode will be exited and the radio will tune to the preset station.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: • The available selections for each of the above entries varies depending upon the disc. TUNE/SCROLL control knob to adjust the minutes. Press the TUNE/SCROLL control knob again to save changes. • These selections can only be made while playing a • Player Defaults - Selecting this item will allow the DVD. user to scroll through the following items and set defaults according to customer preference.
UNDERSTANDING YOUR INSTRUMENT PANEL 177 down and selecting ⬙other.⬙ Enter the country code using Aspect Ratio — If Equipped the TUNE/SCROLL control knob to scroll up and down Selecting this item allows you to choose between wide screen, pan scan, and letter box. to select the number and then push to select. Subtitle Language — If Equipped Selecting this item allows you to choose a default subtitle language (effective only if the language is supported by the disc).
UNDERSTANDING YOUR INSTRUMENT PANEL SET Button — To Set the Pushbutton Memory When you are receiving a station that you wish to commit to pushbutton memory, press the SET button. The symbol SET 1 will now show in the display window. Select the button (1-6) you wish to lock onto this station and press and release that button. If a button is not selected within five seconds after pressing the SET button, the station will continue to play but will not be stored into pushbutton memory.
UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! The radio may shut down during extremely hot conditions. When this occurs, the radio will indicate “Disc Hot” and shut off until a safe temperature is reached. This shutdown is necessary to protect the optics of the DVD player and other radio internal components. 179 Radio display will show ⬙LOADING DISC⬙ when the disc is loading and “READING DISC” when the radio is reading the disc. CAUTION! This CD player will accept 4–3/4 in (12 cm) discs only.
UNDERSTANDING YOUR INSTRUMENT PANEL The disc can be ejected with the radio and ignition OFF. RW/FF (CD MODE) Press and hold FF (Fast Forward) and the CD player will SEEK Button (CD MODE) begin to fast forward until FF is released, or RW or Press the right SEEK button for the next selection on the another CD button is pressed. The RW (Rewind) button CD. Press the left SEEK button to return to the beginning works in a similar manner.
UNDERSTANDING YOUR INSTRUMENT PANEL 181 Supported Medium Formats (File Systems) The medium formats supported by the radio are ISO 9660 Level 1 and Level 2 and includes the Joliet extension. When reading discs recorded using formats other than ISO 9660 Level 1 and Level 2, the radio may fail to read files properly and may be unable to play the file normally. UDF and Apple HFS formats are not supported. Multisession disc formats are supported by the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL frequencies in the following table are supported. In ID3 Tag information for artist, song title, and album title addition, variable bit rates (VBR) are also supported. The are supported for ID3 version 1 tags. ID3 version 2 is not majority of MP3/WMA files use a 44.1 kHz sampling rate supported by the radios. and a 192, 160, 128, 96 or VBR bit rates. Playlist files are not supported. MP3 Pro files are not MPEG Sampling supported.
UNDERSTANDING YOUR INSTRUMENT PANEL 183 • Number of files and folders - Loading times will INFO Button (DISC Mode for MP3/WMA Play) Pressing the INFO button repeatedly will scroll through increase with more files and folders the following TAG information: Song Title, Artist, File To increase the speed of disc loading, it is recommended Name, and Folder Name (if available). to use CD-R media and single-session discs.
UNDERSTANDING YOUR INSTRUMENT PANEL Pressing the AUX button will change the mode to auxil- TIME Button (Auxiliary Mode) Press the TIME button to change the display from iary device if the AUX jack is connected. elapsed playing time to time of day. The time of day will NOTE: The AUX device must be turned on and the display for five seconds. device’s volume set to the proper level. If the AUX audio is not loud enough, turn the device’s volume up.
UNDERSTANDING YOUR INSTRUMENT PANEL 185 Dolby威 Operating Instructions - uconnect™ phone (If Manufactured under license from Dolby威 Laboratories. Equipped) Refer to “uconnect™ phone” in the uconnect™ User ⬙Dolby威⬙ and the double-D symbol are trademarks of Dolby威 Laboratories. Manual located on the DVD for further details.
UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE (RER/REN) — AM/FM/CD/DVD RADIO – IF EQUIPPED NOTE: The sales code is located on the lower right side of the unit’s faceplate. Operating Instructions — uconnect™ phone — If Equipped Refer to “uconnect™ phone” in the uconnect™ User Manual located on the DVD for further details. Clock Setting Procedure The REN and RER radios contain a CD/DVD player, USB port, and a 30-gigabyte hard drive (HDD). Sirius Satellite uconnect™ gps — RER only Radio is optional.
UNDERSTANDING YOUR INSTRUMENT PANEL 4. To move the hour forward, touch the screen where the word “Hour” with the arrow pointing upward is displayed. To move the hour backward, touch the screen where the word “Hour” with the arrow pointing downward is displayed. 187 2. Touch the screen where the time is displayed. The clock setting menu will appear on the screen. 3. When this feature is on, a check mark will appear in the box next to the words “Daylight Savings.
UNDERSTANDING YOUR INSTRUMENT PANEL Changing the Time Zone 1. Turn on the radio. 2. Touch the screen where the time is displayed. The clock setting menu will appear on the screen. 3. Touch the screen where the words “Set Time Zone” are displayed. The time zone selection menu will appear on the screen. 4. Select a time zone by touching the screen where your selection appears.
UNDERSTANDING YOUR INSTRUMENT PANEL 189 Power Switch/Volume Control (Rotary) TIME Button Push the ON/VOLUME control knob to turn on the Press the TIME button to alternate display of the time radio. Push the ON/VOLUME control knob a second and radio frequency. time to turn off the radio. Clock Setting Procedure Electronic Volume Control 1. Press and hold the TIME button until the hours blink. The electronic volume control turns continuously (360 degrees) in either direction, without stopping. Turning 2.
UNDERSTANDING YOUR INSTRUMENT PANEL RW/FF Pressing the RW (Rewind) or FF (Fast Forward) buttons causes the tuner to search for the next frequency in the direction of the arrows. This feature operates in either AM or FM frequencies. Push the rotary TUNE/SCROLL control knob a third time and TREBLE will display. Turn the TUNE/SCROLL control knob to the right or left to increase or decrease the treble tones.
UNDERSTANDING YOUR INSTRUMENT PANEL SET/RND Button — To Set the Pushbutton Memory When you are receiving a station that you wish to commit to pushbutton memory, press the SET/RND button. The symbol SET 1 will now show in the display window. Select the button (1 to 6) you wish to lock onto this station and press and release that button. If a button is not selected within five seconds after pressing the SET/RND button, the station will continue to play but will not be stored into pushbutton memory.
UNDERSTANDING YOUR INSTRUMENT PANEL Inserting Compact Disc(s) Gently insert one CD into the CD player with the CD label facing up. The CD will automatically be pulled into the CD player and the CD icon will illuminate on the radio display. If a CD does not go into the slot more than 1.0 in (2.5 cm), a disc may already be loaded and must be ejected before a new disc can be loaded. CAUTION! (Continued) • Do not use adhesive labels. These labels can peel away and jam the player mechanism.
UNDERSTANDING YOUR INSTRUMENT PANEL 193 NOTE: Ejecting with the ignition OFF is not allowed on AM/FM Button Press the button to select either AM or FM mode. convertible or soft-top models (if equipped). SEEK Button Press the right SEEK button for the next selection on the CD. Press the left SEEK button to return to the beginning of the current selection, or return to the beginning of the previous selection if the CD is within the first second of the current selection.
UNDERSTANDING YOUR INSTRUMENT PANEL Supported Media (Disc Types) The MP3 file recording media supported by the radio are CDDA, CD-R, CD-RW, MP3, and CDDA+MP3. a number instead. With a maximum number of files, exceeding 20 folders will result in this display. With 200 files, exceeding 50 folders will result in this display.
UNDERSTANDING YOUR INSTRUMENT PANEL Supported MP3 File Formats The radio will recognize only files with the *.MP3 extension as MP3 files. Non-MP3 files named with the *.MP3 extension may cause playback problems. The radio is designed to recognize the file as an invalid MP3 and will not play the file. When using the MP3 encoder to compress audio data to an MP3 file, the bit rate and sampling frequencies in the following table are supported. In addition, variable bit rates (VBR) are also supported.
UNDERSTANDING YOUR INSTRUMENT PANEL Loading times for playback of MP3 files may be affected Operation Instructions - Auxiliary Mode The auxiliary (AUX) jack is an audio input jack, which by the following: allows the user to plug in a portable device, such as an • Media - CD-RW media may take longer to load than MP3 player, or cassette player, and utilize the vehicle’s CD-R media audio system to amplify the source and play through the • Medium formats - Multisession discs may take longer vehicle speake
UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE RES/RSC — AM/FM STEREO RADIO WITH CD PLAYER (MP3 AUX JACK) AND SIRIUS RADIO 197 Operating Instructions — Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. NOTE: The radio sales code is located on the lower right Power Switch/Volume Control (Rotary) side of the radio faceplate. Push the ON/VOLUME control knob to turn on the radio. Push the ON/VOLUME control knob a second time to turn off the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations without stopping until you release it. Phone Button uconnect™ phone — If Equipped Press this button to operate the uconnect™ phone feature (if equipped). Refer to “uconnect™ phone” in the uconnect™ User Manual located on the DVD for further details.
UNDERSTANDING YOUR INSTRUMENT PANEL 199 3. After adjusting the hours, press the right side TUNE/ INFO Button SCROLL control knob to set the minutes. The minutes Press the INFO button for an RDS station (one with call letters displayed). The radio will return a Radio Text will begin to blink. message broadcast from an FM station (FM mode only). 4. Adjust the minutes using the right side TUNE/ SCROLL control knob.
UNDERSTANDING YOUR INSTRUMENT PANEL Push the rotary TUNE/SCROLL control knob a second Push the rotary TUNE/SCROLL control knob again to time and MID will display. Turn the TUNE/SCROLL exit setting tone, balance, and fade. control knob to the right or left to increase or decrease the MUSIC TYPE Button mid-range tones. Pressing this button once will turn on the Music Type Push the rotary TUNE/SCROLL control knob a third mode for five seconds. Pressing the MUSIC TYPE button time and TREBLE will display.
UNDERSTANDING YOUR INSTRUMENT PANEL Program Type Classic Rock College Country Foreign Language Information Jazz News Nostalgia Oldies Personality Public Rhythm and Blues Religious Music Religious Talk Rock 16-Digit Character Display Cls Rock College Country Language Inform Jazz News Nostalga Oldies Persnlty Public R&B Rel Musc Rel Talk Rock Program Type Soft Soft Rock Soft Rhythm and Blues Sports Talk Top 40 Weather 201 16-Digit Character Display Soft Soft Rck Soft R&B Sports Talk Top 40 Weather By pr
UNDERSTANDING YOUR INSTRUMENT PANEL station and press and release that button. If a button is SETUP Button Pressing the SETUP button allows you to select between not selected within five seconds after pressing the SET/ RND button, the station will continue to play but will not the following items: be stored into pushbutton memory. • Set Clock — Pressing the SELECT button will allow you to set the clock.
UNDERSTANDING YOUR INSTRUMENT PANEL 203 radio display. If a CD does not go into the slot more than DISC/AUX Button Pressing the DISC/AUX button will allow you to switch 1.0 in (2.5 cm), a disc may already be loaded and must be ejected before a new disc can be loaded. from AM/FM modes to DISC/AUX mode. If you insert a disc with the ignition ON and the radio ON, the unit will switch from radio to CD mode and begin to play when you insert the disc.
UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! (Continued) • Dual-media disc types (one side is a DVD, the other side is a CD) should not be used, and they can cause damage to the player. EJECT Button - Ejecting a CD Press the EJECT button to eject the CD. SEEK Button Press the right SEEK button for the next selection on the CD.
UNDERSTANDING YOUR INSTRUMENT PANEL 205 SET/RND Button (Random Play Button) Press this button while the CD is playing to activate Random Play. This feature plays the selections on the compact disc in random order to provide an interesting change of pace. Supported Medium Formats (File Systems) The medium formats supported by the radio are ISO 9660 Level 1 and Level 2 and includes the Joliet extension.
UNDERSTANDING YOUR INSTRUMENT PANEL • Maximum number of characters in file/folder names: extension may cause playback problems. The radio is designed to recognize the file as an invalid MP3 and will • Level 1: 12 (including a separator ⬙.⬙ and a threenot play the file. character extension) When using the MP3 encoder to compress audio data to • Level 2: 31 (including a separator ⬙.⬙ and a threean MP3 file, the bit rate and sampling frequencies in the character extension) following table are supported.
UNDERSTANDING YOUR INSTRUMENT PANEL 207 ID3 Tag information for artist, song title, and album title • Number of files and folders - Loading times will are supported for version 1 ID3 tags. ID3 version 2 is not increase with more files and folders supported by the radios. To increase the speed of disc loading, it is recommended Playlist files are not supported. MP3 Pro files are not to use CD-R media and single-session discs. To create a supported.
UNDERSTANDING YOUR INSTRUMENT PANEL Pressing the AUX button will change the mode to auxilINFO Button (CD Mode for MP3 Play) Pressing the INFO button repeatedly will scroll through iary device if the AUX jack is connected. the following TAG information: Song Title, Artist, File NOTE: The AUX device must be turned on and the Name, and Folder Name (if available). device’s volume set to the proper level.
UNDERSTANDING YOUR INSTRUMENT PANEL 209 Operating Instructions - uconnect™ studios (Satellite Radio) (If Equipped) Refer to “uconnect™ studios (Satellite Radio)” in the uconnect™ User Manual located on the DVD for further details. System Activation Sirius Satellite Radio service is pre-activated, and you may begin listening immediately to the one year of audio service that is included with the factory-installed satellite radio system in your vehicle.
UNDERSTANDING YOUR INSTRUMENT PANEL To access the ESN/SID, refer to the following steps: Satellite Antenna To ensure optimum reception, do not place items on the roof around the rooftop antenna location. Metal objects placed within the line of sight of the antenna will cause decreased performance. Larger luggage items such as bikes should be placed as far rearward as possible, within the loading design of the rack. Do not place items directly on or above the antenna.
UNDERSTANDING YOUR INSTRUMENT PANEL 211 INFO Button Pressing the INFO button will cycle the display information between Artist, Song Title, and Composer (if availNOTE: The ignition switch must be in the ON or ACC able). Also, pressing and holding the INFO button for an position to operate the radio. additional three seconds will make the radio display the SEEK Buttons Song Title all of the time (press and hold again to return Press and release the SEEK buttons to search for the next to normal display).
UNDERSTANDING YOUR INSTRUMENT PANEL turning the TUNE/SCROLL control knob within five sec- SET Button – To Set the Pushbutton Memory When you are receiving a channel that you wish to onds will allow the program format type to be selected. commit to pushbutton memory, press the SET button. Toggle the MUSIC TYPE button again to select the music The symbol SET 1 will now show in the display window. type.
UNDERSTANDING YOUR INSTRUMENT PANEL 213 Every time a preset button is used, a corresponding button number will display. Buttons 1 - 6 These buttons tune the radio to the channels that you commit to pushbutton memory (12 Satellite stations). Operating Instructions - uconnect™ phone (If Equipped) Refer to “uconnect™ phone” in the uconnect™ User Manual located on the DVD for further details.
UNDERSTANDING YOUR INSTRUMENT PANEL • A battery-powered infrared remote control snaps into a molded compartment in the center console armrest upper storage bin. VES™ Video Screen NOTE: Close the armrest after the LCD screen has been raised to its viewing position. VES™ Remote Control • The radio and DVD player controls allow front seat operation for easy setup in the case of younger rear • Two wireless infrared headsets allow rear seat passengers to listen to the same or individual audio sources.
UNDERSTANDING YOUR INSTRUMENT PANEL 215 Audio/Video RCA Jacks (AUX Jacks) are rocker-type switches with a pushbutton in the center on the rear of the center console enable of each switch. Reach behind the steering wheel to access the monitor to display video directly the switches. from a video camera, connect video games for display on the screen, or play music directly from an MP3 player. 4 1. Video in (yellow) 2. Left audio in (white) 3.
UNDERSTANDING YOUR INSTRUMENT PANEL Right-Hand Switch Functions • Press the top of the switch to increase the volume. • Press the bottom of the switch to decrease the volume. Left-Hand Switch Functions for Media (i.e., CD) Operation • Press the top of the switch once to listen to the next track. • Press the button in the center of the switch to change • Press the bottom of the switch once either to listen to modes (i.e., AM, FM, etc.).
UNDERSTANDING YOUR INSTRUMENT PANEL 217 NOTE: If you experience difficulty in playing a particuCD/DVD MAINTENANCE To keep a CD/DVD in good condition, take the following lar disc, it may be damaged (i.e., scratched, reflective precautions: coating removed, a hair, moisture or dew on the disc) oversized, or have protection encoding. Try a known 1. Handle the disc by its edge; avoid touching the good disc before considering disc player service. surface. 2.
UNDERSTANDING YOUR INSTRUMENT PANEL Manual Heating and Air Conditioning Blower Control Rotate this control to regulate the amount of air forced through the ventilation system in any mode. The blower speed increases as you move the control to the right from the “O” (OFF) position. There are four blower speeds. NOTE: For vehicles equipped with Remote Start, the climate controls will not function during Remote Start operation if the blower control is left in the “O” (Off) position.
UNDERSTANDING YOUR INSTRUMENT PANEL 219 Temperature Control Mode Control (Air Direction) Rotate this control to regulate the temRotate this control to choose from sevperature of the air inside the passenger eral patterns of air distribution. You compartment. Rotating the dial left can select either a primary mode as into the blue area of the scale indicates identified by the symbols on the concooler temperatures while rotating trol, or a blend of two of these modes.
UNDERSTANDING YOUR INSTRUMENT PANEL Defrost Bi-Level Air is directed through the panel and floor outlets. Air is directed through the windshield and side window demist outlets. Use this mode with maximum blower and temperature settings for best windNOTE: For all settings except full cold or full hot, there shield and side window defrosting. is a difference in temperature between the upper and lower outlets. The warmer air flows to the floor outlets.
UNDERSTANDING YOUR INSTRUMENT PANEL 221 will cause the LED in the control button to illuminate. • Recirculated air is not allowed in Floor, Mix or Defrost After ten minutes, the system will return to normal mode modes. If the Recirculation button is depressed while function and the LED will turn off. in any of these modes, the LED indicator will flash several times then go out. Recirculation will be disNOTE: abled automatically is these modes are selected.
UNDERSTANDING YOUR INSTRUMENT PANEL Air Conditioning Control Automatic Temperature Control (ATC) — If Press this button to engage the Air Equipped Conditioning. A light will illuminate when the Air Conditioning System is engaged. Rotating the dial left into the blue area of the scale indicates cooler temperatures while rotating right into the red area indicates warmer temperatures. NOTE: The air conditioning compressor will not engage until the engine has been running for about 10 seconds.
UNDERSTANDING YOUR INSTRUMENT PANEL 223 You will experience the greatest efficiency by simply allowing the system to function automatically. Selecting 1. Turn the Mode Control knob (on the right) and the the “O” (OFF) position on the blower control stops the Blower Control knob (on the left) to AUTO. system completely and closes the outside air intake. NOTE: The AUTO position performs best for front seat 72°F (22°C) is the recommended setting for maximum occupants only.
UNDERSTANDING YOUR INSTRUMENT PANEL • If your air conditioning performance seems lower than expected, check the front of the A/C condenser located in front of the radiator for an accumulation of dirt or insects. Clean with a gentle water spray from behind the radiator and through the condenser. Fabric front fascia protectors may reduce airflow to the condenser, reducing air conditioning performance.
UNDERSTANDING YOUR INSTRUMENT PANEL 225 4
UNDERSTANDING YOUR INSTRUMENT PANEL The operator can override the AUTO mode setting to • Floor change airflow distribution by rotating the Mode Control Air is directed through the floor outlets with a knob (on the right) to one of the following positions. small amount flowing through the defrost and side window demist outlets. • Panel Air is directed through the outlets in the instrument • Mix Air is directed through the floor, defrost, and side panel. These outlets can be adjusted to direct airflow.
UNDERSTANDING YOUR INSTRUMENT PANEL • Air Conditioner Control Press this button to turn on the air conditioning during manual operation only. When the air conditioning is turned on, cool dehumidified air will flow through the outlets selected with the Mode control dial. Press this button a second time to turn OFF the air conditioning. An LED in the button illuminates when manual compressor operation is selected. • Recirculation Control The system will automatically control recirculation.
UNDERSTANDING YOUR INSTRUMENT PANEL • Most of the time, when in Automatic Operation, you can temporarily put the system into Recirculation Mode by pressing the Recirculation button. However, under certain conditions, while in Automatic Mode, the system is blowing air out the defrost vents. When these conditions are present, and the Recirculation button is pressed, the indicator will flash and then turn off. This tells you that you are unable to go into Recirculation Mode at this time.
UNDERSTANDING YOUR INSTRUMENT PANEL Window Fogging Interior fogging on the windshield can be quickly removed by turning the mode selector to Defrost. The Mix mode can be used to maintain a clear windshield and provide sufficient heating. If side window fogging becomes a problem, increase blower speed. Vehicle windows tend to fog on the inside in mild but rainy or humid weather. NOTE: Recirculate without A/C should not be used for long periods as fogging may occur.
UNDERSTANDING YOUR INSTRUMENT PANEL Control Setting Suggestions for Various Weather Conditions
STARTING AND OPERATING CONTENTS 䡵 Starting Procedures . . . . . . . . . . . . . . . . . . . . 235 ▫ Key Ignition Park Interlock . . . . . . . . . . . . . 240 ▫ Automatic Transaxle . . . . . . . . . . . . . . . . . . 235 ▫ Brake/Transaxle Interlock System . . . . . . . . . 240 ▫ Normal Starting . . . . . . . . . . . . . . . . . . . . . 235 ▫ Automatic Transaxle Ignition Interlock System . . . . . . . . . . . . . . . . . . . . . . . . . . . . 241 ▫ Extreme Cold Weather (Below ⫺20°F Or ⫺29°C) . . . . . .
STARTING AND OPERATING 䡵 Driving On Slippery Surfaces . . . . . . . . . . . . . 247 ▫ Brake Assist System (BAS) . . . . . . . . . . . . . . 257 ▫ Acceleration . . . . . . . . . . . . . . . . . . . . . . . . 247 ▫ Hill Start Assist (HSA) — If Equipped . . . . . 258 ▫ Traction . . . . . . . . . . . . . . . . . . . . . . . . . . . 248 ▫ Electronic Stability Control (ESC) . . . . . . . . . 260 䡵 Driving Through Water . . . . . . . . . . . . . . . . . 248 䡵 Tire Safety Information . . . . . . . . .
STARTING AND OPERATING 233 ▫ Tread Wear Indicators . . . . . . . . . . . . . . . . . 277 ▫ Reformulated Gasoline . . . . . . . . . . . . . . . . 291 ▫ Life Of Tire . . . . . . . . . . . . . . . . . . . . . . . . 278 ▫ Gasoline/Oxygenate Blends . . . . . . . . . . . . . 291 ▫ Replacement Tires . . . . . . . . . . . . . . . . . . . . 278 ▫ E-85 Usage In Non-Flex Fuel Vehicles . . . . . . 292 䡵 Tire Chains . . . . . . . . . . . . . . . . . . . . . . . . . . 279 ▫ MMT In Gasoline . . . . . . . . . . .
STARTING AND OPERATING ▫ Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . 298 ▫ Loading . . . . . . . . . . . . . . . . . . . . . . . . . . . 303 ▫ Cruising Range . . . . . . . . . . . . . . . . . . . . . . 298 䡵 Trailer Towing . . . . . . . . . . . . . . . . . . . . . . . . 304 ▫ Replacement Parts . . . . . . . . . . . . . . . . . . . 299 ▫ Common Towing Definitions . . . . . . . . . . . . 304 ▫ Maintenance . . . . . . . . . . . . . . . . . . . . . . . .
STARTING AND OPERATING STARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust the inside and outside mirrors, fasten your seat belt, and if present, instruct all other occupants to buckle their seat belts. WARNING! • Never leave children alone in a vehicle. Leaving children in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Do not leave the keys in the ignition.
STARTING AND OPERATING For vehicles equipped with Tip Start (Six-Speed Trans- If Engine Fails To Start axle), turn the ignition switch to the START position and WARNING! release it as soon as the starter engages. The starter motor will continue to run, and it will disengage automatically • Never pour fuel or other flammable liquids into when the engine is running. If the engine fails to start, the the throttle body air inlet opening in an attempt to starter will disengage automatically in 10 seconds.
STARTING AND OPERATING WARNING! (Continued) • Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transaxle cannot be started this way. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle. If the vehicle has a discharged battery, booster cables may be used to obtain a start from a booster battery or the battery in another vehicle. This type of start can be dangerous if done improperly.
STARTING AND OPERATING With Tip Start If the engine fails to start after you have followed the “Normal Starting” or “Extreme Cold Weather” procedures, it may be flooded. To clear any excess fuel, push the accelerator pedal all the way to the floor and hold it. Then, turn the ignition switch to the START position and release it as soon as the starter engages. The starter motor will disengage automatically in 10 seconds.
STARTING AND OPERATING AUTOMATIC TRANSAXLE CAUTION! Damage to the transaxle may occur if the following precautions are not observed: • Shift the shift lever into PARK only after the vehicle has come to a complete stop. • Shift the shift lever into or out of REVERSE only after the vehicle has come to a complete stop and the engine is at idle speed. • Do not shift the shift lever from REVERSE, PARK, or NEUTRAL into any forward gear when the engine is above idle speed.
STARTING AND OPERATING WARNING! (Continued) • Unintended movement of a vehicle could injure those in and near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, you should always shift the vehicle into PARK, remove the key from the ignition, and apply the parking brake. Once the key is removed from the ignition, the shift lever is locked in the PARK position, securing the vehicle against unwanted movement.
STARTING AND OPERATING 241 • Insert the ignition key into the ignition switch and Automatic Transaxle Ignition Interlock System This system prevents the key from being removed unless rotate it to the ON position. the shift lever is in PARK. It also prevents shifting out of • Remove the cup holder liner. PARK unless the ignition switch is in the ON position, • Insert a key, screwdriver, or finger into the hole at the and the brake pedal is applied.
STARTING AND OPERATING Four-Speed/Six-Speed Automatic Transaxle The electronically controlled transaxle provides a precise shift schedule. The transaxle electronics are self-calibrating; therefore, the first few shifts on a new vehicle may be somewhat abrupt. This is a normal condition, and precision shifts will develop within a few hundred miles/kilometers. Gear Ranges PARK This range supplements the parking brake by locking the transaxle. The engine can be started in this range.
STARTING AND OPERATING WARNING! Never use PARK as a substitute for the parking brake. Always apply parking brake fully when parked to guard against vehicle movement and possible injury or damage. 243 NEUTRAL This range is used when vehicle is standing for prolonged periods with engine running. Engine may be started in this range. Set the parking brake if you must leave the vehicle.
STARTING AND OPERATING transaxle shifting occurs in the DRIVE range. For example: When operating the vehicle under heavy loading conditions, (i.e., in hilly terrain, traveling into strong headwinds, or while towing heavy trailers). Under these conditions, reducing shifting by selecting the appropriate gear in AutoStick威 will improve the performance and extend transmission life by reducing excessive shifting and heat build-up.
STARTING AND OPERATING LOW — Four-Speed Transaxle This range should be used for engine braking when descending very steep grades. In this range, upshifts will occur only to prevent engine overspeed while downshifts occur earlier than other gear range selections. CAUTION! If the transaxle operating temperature exceeds acceptable limits, the vehicle computer will override DRIVE (OVERDRIVE) and [5] for six–speed AutoStick威 transaxle and [3] for four–speed transaxle, range by changing shift points.
STARTING AND OPERATING NOTE: Even if the transaxle can be reset, it is recommended that you visit a dealer at your earliest possible convenience. Your dealer has diagnostic equipment to determine if the problem could recur. Moving the shift lever to the left (-) triggers a downshift and to the right (+) an upshift. The gear position will display in the instrument cluster on the transaxle range indicator. If the transaxle cannot be reset, dealer service is required.
STARTING AND OPERATING 247 • Starting out in second gear is helpful in snowy or icy DRIVING ON SLIPPERY SURFACES conditions. Acceleration • Avoid using speed control when Autostick威 is engaged. Rapid acceleration on snow covered, wet, or other slip• The transaxle will automatically shift up when maximum pery surfaces may cause the front wheels to pull erratically to the right or left. This phenomenon occurs when engine speed is reached while Autostick威 is engaged.
STARTING AND OPERATING Traction When driving on wet or slushy roads, it is possible for a wedge of water to build up between the tire and road surface. This is hydroplaning and may cause partial or complete loss of vehicle control and stopping ability. To reduce this possibility, the following precautions should be observed: 1. Slow down during rainstorms or when roads are slushy. 2. Slow down if the road has standing water or puddles. 3.
STARTING AND OPERATING Shallow Standing Water Although your vehicle is capable of driving through shallow standing water, consider the following Caution and Warning before doing so. CAUTION! • Always check the depth of the standing water before driving through it. Never drive through standing water that is deeper than the bottom of the tire rims mounted on the vehicle.
STARTING AND OPERATING WARNING! • Driving through standing water limits your vehicle’s traction capabilities. Do not exceed 5 mph (8 km/h) when driving through standing water. • Driving through standing water limits your vehicle’s braking capabilities, which increases stopping distances. Therefore, after driving through standing water, drive slowly and lightly press on the brake pedal several times to dry the brakes.
STARTING AND OPERATING WARNING! Continued operation with reduced power steering assist could pose a safety risk to yourself and others. Service should be obtained as soon as possible. CAUTION! Prolonged operation of the steering system at the end of the steering wheel travel will increase the steering fluid temperature and it should be avoided when possible. Damage to the power steering pump may occur.
STARTING AND OPERATING If necessary, add fluid to restore to the proper indicated level. With a clean cloth, wipe any spilled fluid from all surfaces. Refer to “Fluids, Lubricants, and Genuine Parts” in Section 7 for the correct fluid type. When parking on a hill, it is important to apply the parking brake before placing the shift lever in PARK, otherwise the load on the transaxle locking mechanism may make it difficult to move the shift lever out of PARK.
STARTING AND OPERATING 253 • If the parking brake is applied while the vehicle is moving, a chime will sound to alert the driver. The chime will sound up to 10 times or until the vehicle has returned to a stop. The “Brake Warning Light” in the instrument cluster will turn on when the parking brake is applied and the ignition switch is on. NOTE: This light only shows that the parking brake is applied. It does not show the degree of brake application.
STARTING AND OPERATING WARNING! WARNING! • Never leave children alone in a vehicle. Leaving children in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Do not leave the key in the ignition. A child could operate power windows, other controls, or move the vehicle. • Be sure the parking brake is fully disengaged before driving: failure to do so can lead to brake failure, and an accident.
STARTING AND OPERATING 255 • The capabilities of an ABS-equipped vehicle must never be exploited in a reckless or dangerous manner, which could jeopardize the user’s safety or the safety of others. If the “Anti-Lock Brake Warning Light” is on, the brake system should be serviced as soon as possible to restore the benefits of anti-lock brakes. If the “Anti-Lock Brake Warning Light” does not come on when the ignition switch is turned to the ON position, have the bulb repaired as soon as possible.
STARTING AND OPERATING ABS is activated during braking under certain road or stopping conditions. ABS-inducing conditions can include ice, snow, gravel, bumps, railroad tracks, loose debris, or panic stops.
STARTING AND OPERATING 257 together to enhance vehicle stability and control in vari- spinning faster than the other, the system will apply the ous driving conditions and are commonly referred to as brake of the spinning wheel. This will allow more engine torque to be applied to the wheel that is not spinning. ESC. This feature remains active even if TCS and ESC are in Anti-Lock Brake System (ABS) the “Partial Off” mode.
STARTING AND OPERATING WARNING! • The BAS cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded. • The BAS cannot prevent accidents, including those resulting from excessive speed in turns, following another vehicle too closely, or hydroplaning. Only a safe, attentive, and skillful driver can prevent accidents.
STARTING AND OPERATING 259 The system will only work if the intended direction of the HSA Activation Criteria The following criteria must be met in order for HSA to vehicle and vehicle gear match. For example, if the intended direction is forward up a hill and the vehicle is activate: in DRIVE and the activation criteria are met, HSA will • Vehicle must be stopped activate.
STARTING AND OPERATING 2. Shift the transmission into NEUTRAL. 3. Apply the parking brake. 10. Repeat these steps if you want to return this feature to it’s previous setting. EVIC Equipped Vehicles HSA is a Customer Programmable Feature on a EVIC 5. Release the clutch pedal. equipped vehicle. If you wish to turn off the HSA feature, refer to “Customer Programmable Features/Electronic 6. Rotate the steering wheel one-half turn to the left. Vehicle Information Center (EVIC)” in Section 4 of this 7.
STARTING AND OPERATING path does not match the intended path, ESC applies the brake of the appropriate wheel to assist in counteracting the oversteer or understeer condition • Over-steer - when the vehicle is turning more than appropriate for the steering wheel position. • Under-steer - when the vehicle is turning less than appropriate for the steering wheel position.
STARTING AND OPERATING ESC Malfunction Indicator Light The “ESC Malfunction Indicator Light” in the instrument cluster will come on when the ignition switch is turned to the ON position. It should go out with the engine running. If the “ESC Malfunction Indicator Light” comes on continuously with the engine running, a malfunction has been detected in the ESC system.
STARTING AND OPERATING Partial ESC Mode This mode is entered by momentarily pressing the “ESC Off” switch (located in the lower switch bank below the heater/air conditioning controls). When in “Partial Off” mode, the TCS portion of ESC, except for the limited slip feature described in the TCS section, has been disabled and the “ESC Off Indicator Light” will be illuminated. All other stability features of ESC function normally, with the exception of engine power reduction.
STARTING AND OPERATING TIRE SAFETY INFORMATION Tire Markings 1 — U.S. DOT Safety Standards Code (TIN) 2 — Size Designation 3 — Service Description 4 — Maximum Load 5 — Maximum Pressure 6 — Treadwear, Traction and Temperature Grades NOTE: • P (Passenger) - Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designation. Example: P215/65R15 95H. • European-Metric tire sizing is based on European design standards.
STARTING AND OPERATING 265 • High flotation tire sizing is based on U.S. design standards and it begins with the tire diameter molded into the sidewall. Example: 31x10.5 R15 LT. Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ⴖ....blank....ⴖ = Passenger car tire based on European design standards LT = Light truck tire based on U.S.
STARTING AND OPERATING EXAMPLE: Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions — The maximum speed corresponding to the speed symbol should only be achieved under specified operating conditions (i.e.
STARTING AND OPERATING Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full TIN, including the date code, located on the white sidewall side of the tire. 267 Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the outboard side, then you will find it on the inboard side of the tire.
STARTING AND OPERATING Tire Loading and Tire Pressure Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar. Tire and Loading Information Placard This placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) total weight your vehicle can carry 3) tire size designed for your vehicle 4) cold tire inflation pressures for the front, rear, and spare tires.
STARTING AND OPERATING NOTE: Under a maximum loaded vehicle condition, gross axle weight ratings (GAWRs) for the front and rear axles must not be exceeded. For further information on GAWRs, vehicle loading, and trailer towing, refer to “Vehicle Loading” in this section. To determine the maximum loading conditions of your vehicle, locate the statement “The combined weight of occupants and cargo should never exceed XXX lbs or XXX kg” on the Tire and Loading Information placard.
STARTING AND OPERATING 5. Determine the combined weight of luggage and cargo NOTE: being loaded on the vehicle. That weight may not safely • The following table shows examples on how to calculate total load, cargo/luggage, and towing capacities exceed the available cargo and luggage load capacity of your vehicle with varying seating configurations calculated in Step 4. and number and size of occupants. This table is for 6.
STARTING AND OPERATING 271 5
STARTING AND OPERATING WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.
STARTING AND OPERATING WARNING! (Continued) • Unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • Always drive with each tire inflated to the recommended cold tire inflation pressure. Economy Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement.
STARTING AND OPERATING CAUTION! After inspecting or adjusting the tire pressure, always reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Tire pressures change by approximately 1 psi (7 kPa) per 12°F (7°C) of air temperature change. Keep this in mind when checking tire pressure inside a garage, especially in the winter.
STARTING AND OPERATING 275 loading may be required for high-speed vehicle opera- Radial-Ply Tires tion. Refer to original equipment or an authorized tire WARNING! dealer for recommended safe operating speeds, loading and cold tire inflation pressures. Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle WARNING! poorly. The instability could cause an accident. AlHigh speed driving with your vehicle under maxiways use radial ply tires in sets of four.
STARTING AND OPERATING WARNING! Temporary use spare tires are for emergency use only. With these tires, do not drive more than 50 mph (80 km/h). Temporary-use spare tires have limited tread life. When the tread is worn to the tread wear indicators, the temporary use spare tire needs to be replaced. Be sure to follow the warnings, which apply to your spare. Failure to do so could result in spare tire failure and loss of vehicle control.
STARTING AND OPERATING 277 Refer to “Freeing A Stuck Vehicle” in Section 6 of this manual for additional information. WARNING! Fast spinning tires can be dangerous. Forces generated by excessive wheel speeds may cause tire damage or failure. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 30 mph (48 km/h) or for more than 30 seconds continuously when you are stuck, and do not let anyone near a spinning wheel, no matter what the speed.
STARTING AND OPERATING Life of Tire Replacement Tires The service life of a tire is dependent upon varying The tires on your new vehicle provide a balance of many factors including but not limited to: characteristics. They should be inspected regularly for wear and correct cold tire inflation pressure.
STARTING AND OPERATING 279 WARNING! WARNING! (Continued) • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle. This can cause unpredictable handling and stress to steering and suspension components. You could lose control and have an accident resulting in serious injury or death.
STARTING AND OPERATING SNOW TIRES Snow tires should be of the same size and type construction as the front tires. Consult the manufacturer of the snow tire to determine any maximum vehicle speed requirement associated with the tire. These tires should always be operated at the vehicle maximum capacity inflation pressures under any load condition. While studded tires improve performance on ice, skid and traction capability on wet or dry surfaces may be poorer than that of non-studded tires.
STARTING AND OPERATING 281 The suggested rotation method is shown in the following TIRE PRESSURE MONITOR SYSTEM (TPMS) The Tire Pressure Monitor System (TPMS) will warn the diagram. driver of a low tire pressure based on the vehicle recommended cold placard pressure. Tire Rotation The tire pressure will vary with temperature by about 1 psi (7 kPa) for every 12 F (7 C). This means that when the outside temperature decreases, the tire pressure will decrease.
STARTING AND OPERATING The TPM System will warn the driver of a low tire pressure if the tire pressure falls below the low-pressure warning limit for any reason, including low temperature effects and natural pressure loss through the tire. The TPM System will continue to warn the driver of low tire pressure as long as the condition exists, and will not turn off until the tire pressure is at or above the recommended cold placard pressure.
STARTING AND OPERATING CAUTION! • The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equipment that is not of the same size, type, and/or style. Aftermarket wheels can cause sensor damage.
STARTING AND OPERATING • Seasonal temperature changes will affect tire pressure, Tire Pressure Monitoring Low Pressure Warnings The “Tire Pressure Monitoring Telltale Light” will and the TPMS will monitor the actual tire pressure in illuminate in the instrument cluster and a chime the tire. will sound when tire pressure is low in one or Base System more of the four active road tires.
STARTING AND OPERATING Check TPMS Warning The “Tire Pressure Monitoring Telltale Light” will flash on and off for 75 seconds and then remain on solid when a system fault is detected. The system fault will also sound a chime. If the ignition key is cycled, this sequence will repeat, providing the system fault still exists. The “Tire Pressure Monitoring Telltale Light” will turn off when the fault condition no longer exists. A system fault can occur due to any of the following: 285 4.
STARTING AND OPERATING 4. For each subsequent ignition key cycle, a chime will NOTE: It is particularly important for you to check the sound and the “TPM Telltale Light” will flash on and off tire pressure in all of the tires on your vehicle monthly and to maintain the proper pressure. for 75 seconds and then remain on solid. 5.
STARTING AND OPERATING Tire Pressure Monitoring Low Pressure Warnings The “Tire Pressure Monitoring Telltale Light” will illuminate in the instrument cluster and a chime will sound when tire pressure is low in one or more of the four active road tires. In addition, the Electronic Vehicle Information Center (EVIC) will display a graphic showing the pressure values of each tire with the low tire pressure values flashing.
STARTING AND OPERATING 1. Jamming due to electronic devices or driving next to facilities emitting the same Radio Frequencies as the TPM sensors. 2. Installing some form of aftermarket window tinting that affects radio wave signals. 3. Lots of snow or ice around the wheels or wheel housings. 4. Using tire chains on the vehicle. 5. Using wheels/tires not equipped with TPM sensors. If the ignition key is cycled, this sequence will repeat, providing the system fault still exists.
STARTING AND OPERATING 289 will remain ON, a chime will sound, and the EVIC will still will display a new pressure value instead of dashes (- -), as long no tire pressure is below the low-pressure warning display a flashing pressure value in the graphic display. limit in any of the four active road tires. The vehicle may 3.
STARTING AND OPERATING FUEL REQUIREMENTS 2.4L and 2.7L Engine All engines are designed to meet all emission regulations and provide excellent fuel economy and performance when using high quality unleaded “regular” gasoline having an octane rating of 87. The use of premium gasoline is not recommended, as it will not provide any benefit over regular gasoline in these engines. 3.5L Engine The 3.
STARTING AND OPERATING Reformulated Gasoline Many areas of the country require the use of cleaner burning gasoline referred to as “Reformulated Gasoline.” Reformulated gasolines contain oxygenates, and are specifically blended to reduce vehicle emissions and improve air quality. 291 CAUTION! For vehicles equipped with a 2.4L or 3.5L engine, DO NOT use gasoline containing Methanol or E85 Ethanol.
STARTING AND OPERATING E-85 Usage In Non-Flex Fuel Vehicles • disconnect and reconnect the battery to reset the Non-FFV vehicles are compatible with gasoline containengine controller memory ing 10% ethanol (E10). Gasoline with higher ethanol More extensive repairs will be required for prolonged content may void the vehicle’s warranty. exposure to E-85 fuel.
STARTING AND OPERATING 293 It is even more important to look for gasolines without Fuel System Cautions MMT in Canada, because MMT can be used at levels CAUTION! higher than those allowed in the United States. MMT is prohibited in Federal and California reformulated gasolines. Materials Added to Fuel All gasoline sold in the United States is required to contain effective detergent additives.
STARTING AND OPERATING CAUTION! (Continued) • The use of fuel additives, which are now being sold as octane enhancers, is not recommended. Most of these products contain high concentrations of methanol. Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsibility of the manufacturer. NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you.
STARTING AND OPERATING WARNING! (Continued) • Guard against carbon monoxide with proper maintenance. Have the exhaust system inspected every time the vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side windows fully open. • Keep the trunk closed when driving your vehicle to prevent carbon monoxide and other poisonous exhaust gases from entering the vehicle. 295 FLEXIBLE FUEL (2.
STARTING AND OPERATING NOTE: The 2.7L engine is now rated for E85 Ethanol use (EXCEPT CALIFORNIA EMISSION STATES). Only vehicles with the E-85 fuel filler door label can operate on E-85. Only vehicles with the E-85 fuel filler door label can operate on E-85.
STARTING AND OPERATING 297 Ethanol Fuel (E-85) For best results, a refueling pattern that avoids alternatE-85 is a mixture of approximately 85% fuel ethanol and ing between E-85 and unleaded gasoline is recom15% unleaded gasoline. mended. WARNING! Ethanol vapors are extremely flammable and could cause serious personal injury. Never have any smoking materials lit in or near the vehicle when removing the fuel filler tube cap (gas cap) or filling the tank.
STARTING AND OPERATING • Some additives used in regular gasoline are not fully compatible with E–85 and may form deposits in your engine. To eliminate driveability issues that may be caused by these deposits, a supplemental gasoline additive, such as MOPAR威 Injector Cleanup or Techron may be used. Selection Of Engine Oil For Flexible Fuel Vehicles (E-85) and Gasoline Vehicles FFV vehicles operated on E-85 require specially formulated engine oils.
STARTING AND OPERATING Replacement Parts Many components in your Flexible Fuel Vehicle (FFV) are designed to be compatible with ethanol. Always be sure that your vehicle is serviced with correct ethanol compatible parts. 299 ADDING FUEL Fuel Filler Cap (Gas Cap) The gas cap is behind the fuel filler door, on the left rear quarter panel of the vehicle. If the gas cap is lost or damaged, be sure the replacement cap is for use with this vehicle.
STARTING AND OPERATING After removing the gas cap, place the gas cap tether cable NOTE: If the gas cap is lost or damaged, be sure the over a hook on the inside of the fuel door. This keeps the replacement cap is for use with this vehicle. gas cap suspended away from and protects the vehicle’s CAUTION! surface. • Damage to the fuel system or emission control system could result from using an improper fuel tank filler tube cap (gas cap).
STARTING AND OPERATING WARNING! • Never have any smoking materials lit in or near the vehicle when the gas cap is removed or the tank filled. • Never add fuel when the engine is running. This is in violation of most state and federal fire regulations and doing so will cause the MIL to turn on. • A fire may result if gasoline is pumped into a portable container that is inside of a vehicle. You could be burned. Always place gas containers on the ground while filling.
STARTING AND OPERATING VEHICLE LOADING The bar code allows a computer scanner to read the Vehicle Identification Number (VIN). Vehicle Certification Label Your vehicle has a certification label attached to the rear Gross Vehicle Weight Rating (GVWR) of the driver’s door. The GVWR is the total allowable weight of your vehicle. This includes driver, passengers, and cargo.
STARTING AND OPERATING WARNING! Because the front wheels steer the vehicle, it is important that you do not exceed the maximum front or rear GAWR. A dangerous driving condition can result if either rating is exceeded. You could lose control of the vehicle and have an accident. 303 Figure out the weight on the front and rear of the vehicle separately. It is important that you distribute the load evenly over the front and rear axles.
STARTING AND OPERATING TRAILER TOWING In this section, you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle. Before towing a trailer, carefully review this information to tow your load as efficiently and safely as possible. Gross Vehicle Weight Rating (GVWR) The GVWR is the total allowable weight of your vehicle. This includes driver, passengers, cargo, and tongue weight. The total load must be limited so that you do not exceed the GVWR.
STARTING AND OPERATING 305 NOTE: The GCWR rating includes a 150 lbs (68 kg) Trailer Tongue Weight (TW) The tongue weight is the downward force exerted on the allowance for the presence of a driver. hitch ball by the trailer. In most cases it should not be less Gross Axle Weight Rating (GAWR) than or more than 10% of the trailer load. You must The GAWR is the maximum capacity of the front and rear consider this as part of the load on your vehicle. axles.
STARTING AND OPERATING Trailer Hitch Classification The following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition. Refer to the Trailer Towing Weights (Maximum Trailer Weight Ratings) chart for the Max. GTW towable for your given drivetrain. Trailer Hitch Classification Definitions Class Max.
STARTING AND OPERATING 307 Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. Maximum Trailer Weight Ratings Max. GTW (Gross Trailer Engine/Transaxle Max. Frontal Area Wt.) 2.4L/Auto See Note 2 1,000 lbs (450 kg) 1,500 lbs (680 kg) 2.7L/Auto See Note 2 3.5L/Auto 22 sq.ft. (2.0 sq.m) 2,000 lbs (900 kg) Refer to local laws for maximum trailer towing speeds.
STARTING AND OPERATING CAUTION! Towing a trailer with a larger than recommended frontal area could cause the engine to overheat or cause severe engine damage under extreme conditions. Trailer and Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% of the Gross Trailer Weight (GTW) on the tow hitch of your vehicle.
STARTING AND OPERATING NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options, or authorized dealer-installed options, must be considered as part of the total load on your vehicle. Refer to the Tire and Loading Information placard in the “Tire Safety Information” section for the maximum combined weight of occupants and cargo for your vehicle.
STARTING AND OPERATING WARNING! WARNING! (Continued) • Improper towing can lead to an injury accident. Follow these guidelines to make your trailer towing as safe as possible: • Make certain that the load is secured in the trailer and that it will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control. You could lose control of your vehicle and have an accident.
STARTING AND OPERATING WARNING! (Continued) • Total weight must be distributed between the tow vehicle and the trailer such that the following four ratings are not exceeded: 1. GVWR 2. GTW 3. GAWR 4. Trailer tongue weight rating for the trailer hitch utilized (This requirement may limit the ability to always achieve 10% of trailer tongue weight as a percentage of total trailer weight). 311 • Proper tire inflation pressures are essential to the safe and satisfactory operation of your vehicle.
STARTING AND OPERATING Towing Requirements — Trailer Brakes • Do not interconnect the hydraulic brake system or vacuum system of your vehicle with that of the trailer. This could cause inadequate braking and possible personal injury. • An electronically actuated trailer brake controller is required when towing a trailer with electronically actuated brakes. When towing a trailer equipped with a hydraulic surge actuated brake system, an electronic brake controller is not required.
STARTING AND OPERATING WARNING! (Continued) • Towing any trailer will increase your stopping distance. When towing, you should allow for additional space between your vehicle and the vehicle in front of you. Failure to do so could result in an accident. 313 Automatic Transaxle The DRIVE range can be selected when towing. However, if frequent shifting occurs while in this range, third gear for a four-speed automatic and the fifth gear for a six-speed AutoStick威 should be selected.
STARTING AND OPERATING NOTE: Check the four-speed automatic transaxle fluid • Highway Driving level before towing. The AutoStick威 six-speed transmis- Reduce speed. sion is sealed and the fluid level cannot be checked. See • Air Conditioning your authorized dealership service center for assistance. Turn off temporarily. Electronic Speed Control — If Equipped RECREATIONAL TOWING (BEHIND • Do not use in hilly terrain or with heavy loads. MOTORHOME, ETC.
WHAT TO DO IN EMERGENCIES CONTENTS 䡵 Hazard Warning Flasher . . . . . . . . . . . . . . . . 316 䡵 Freeing A Stuck Vehicle . . . . . . . . . . . . . . . . . 328 䡵 If Your Engine Overheats . . . . . . . . . . . . . . . . 316 䡵 Towing A Disabled Vehicle . . . . . . . . . . . . . . . 329 ▫ Engine Oil Overheating (2.4L Engine Only) — If Equipped . . . . . . . . 317 ▫ Towing With The Ignition Key . . . . . . . . . . . 329 䡵 Jacking And Tire Changing . . . . . . . . . . . . . . . 318 ▫ Jack Location . . . .
WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER IF YOUR ENGINE OVERHEATS The Hazard Warning flasher switch is located on the In any of the following situations, you can reduce the instrument panel, below the radio. potential for overheating by taking the appropriate action. Press the switch to turn on the Hazard Warning flasher. When the switch is activated, all directional • On the highways — Slow down.
WHAT TO DO IN EMERGENCIES NOTE: There are steps that you can take to slow down an impending overheat condition: • If your air conditioner (A/C) is on, turn it off. The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat. 317 WARNING! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call a service center if your vehicle overheats.
WHAT TO DO IN EMERGENCIES NOTE: The vehicle speed is reduced to a maximum of 53 mph (85 km/h). You may of course, reduce your vehicle speed further if needed. JACKING AND TIRE CHANGING WARNING! • Being under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never put any part of your body under a vehicle that is on a jack. Never start or run the engine while the vehicle is on a jack.
WHAT TO DO IN EMERGENCIES Spare Tire Removal Lift up the load floor cover and remove the hold down. 319 Preparations For Jacking 1. Park the vehicle on a firm, level surface. Avoid ice or slippery areas. WARNING! Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. 2. Set the parking brake. Spare Tire and Jack Stowage 3.
WHAT TO DO IN EMERGENCIES 6. Block both the front and rear of the wheel diagonally opposite the jacking position. For example, if changing the right front tire, block the left rear wheel. NOTE: Passengers should not remain in the vehicle while the vehicle is being jacked.
WHAT TO DO IN EMERGENCIES WARNING! (Continued) • If working on or near a roadway, be extremely careful of motor traffic. • To assure that spare tires, flat or inflated, are securely stowed, spares must be stowed with the valve stem facing the ground. • Turn on the Hazard Warning flasher. 321 NOTE: The jack handle attaches to the side of the jack with two attachment points. When the jack is partially expanded, the tension between the two attachment points holds the jack handle in place.
WHAT TO DO IN EMERGENCIES Jacking Locations
WHAT TO DO IN EMERGENCIES 323 CAUTION! WARNING! Do not attempt to raise the vehicle by jacking on locations other than those indicated in Step 3. Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 3. There are two front jacking locations and two rear jacking locations on each side of the body (as pictured above). 5.
WHAT TO DO IN EMERGENCIES WARNING! WARNING! To avoid possible personal injury, handle the wheel covers with care to avoid contact with any sharp edges. A loose tire or jack thrown forward in a collision or hard stop could endanger the occupants of the vehicle. Always stow the jack parts and the spare tire in the places provided. 7. Lower the vehicle by turning the jack screw to the left. 10. Place the deflated (flat) tire in the cargo area and have 8. Finish tightening the nuts.
WHAT TO DO IN EMERGENCIES JUMP-STARTING PROCEDURE Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transmission cannot be started this way. Also, there is a greater risk of an accident when a vehicle is being pushed or towed. If the vehicle has a discharged battery, booster cables may be used to obtain a start from a booster battery or the battery in another vehicle. This type of start can be dangerous if done improperly, so follow this procedure carefully.
WHAT TO DO IN EMERGENCIES The battery is stored between the left front headlight assembly and the left front wheel splash shield. Access is through the splash shield. Jump-starting remote battery terminals are located under the hood. WARNING! Do not permit vehicles to touch each other as this could establish a ground connection and personal injury could result. 1. Wear eye protection and remove any metal jewelry 3.
WHAT TO DO IN EMERGENCIES 5. Connect the other cable, first to the negative terminal of the booster battery and then to the engine ground (-) of the vehicle with the discharged battery. Make sure you have a good contact on the engine ground. Refer to the following illustration for jump-starting connections. Jump-Starting Location 327 WARNING! • Do not connect the cable to the negative post of the discharged battery.
WHAT TO DO IN EMERGENCIES 7. Start the engine in the vehicle that has the booster battery, let the engine idle a few minutes, and then start the engine in the vehicle with the discharged battery. 8. When removing the jumper cables, reverse the sequence exactly. Be careful of the moving belts and fan. 9. Reinstall the protective cover over the remote jumpstart positive battery post.
WHAT TO DO IN EMERGENCIES NOTE: If your vehicle is equipped with Electronic Stability Control (ESC), turn the system to Partial OFF before attempting to “rock” the vehicle. Refer to “Electronic Brake Control” in Section 5 for further information on of this manual. CAUTION! • When “rocking” a stuck vehicle by moving between 1st and REVERSE, do not spin the wheels faster than 15 mph (24 km/h), or drivetrain damage may result.
WHAT TO DO IN EMERGENCIES • The towing speed must not exceed 25 mph (40 km/h). CAUTION! • Exceeding these towing limits may cause a transaxle failure. • If the transaxle is inoperative, or if the vehicle is to be towed more than 15 miles (25 km), the vehicle must be transported either with a flatbed truck or with the front wheels off the ground, otherwise, transaxle damage may occur.
WHAT TO DO IN EMERGENCIES Towing This Vehicle Behind Another Vehicle Flat towing with all four wheels on the ground of vehicles equipped with an automatic transmission, is only permitted within the limitations described in this section. 331 Battery power is required to release the brake/transaxle interlock system. There is an override system that allows you to shift out of PARK in case of loss of power. To activate the override system: • Firmly apply the parking brake.
MAINTAINING YOUR VEHICLE CONTENTS 䡵 Engine Compartment — 2.4L . . . . . . . . . . . . . 335 䡵 Maintenance Procedures . . . . . . . . . . . . . . . . . 341 䡵 Engine Compartment — 2.7L . . . . . . . . . . . . . 336 ▫ Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . 342 䡵 Engine Compartment — 3.5L . . . . . . . . . . . . . 337 ▫ Engine Oil Filter . . . . . . . . . . . . . . . . . . . . . 345 䡵 Onboard Diagnostic System — OBD II . . . . . . 338 ▫ Engine Air Cleaner Filter . . . . . . . . . .
MAINTAINING YOUR VEHICLE ▫ Adding Washer Fluid . . . . . . . . . . . . . . . . . 352 䡵 Bulb Replacement . . . . . . . . . . . . . . . . . . . . . 377 ▫ Exhaust System . . . . . . . . . . . . . . . . . . . . . 352 ▫ Headlamp . . . . . . . . . . . . . . . . . . . . . . . . . 377 ▫ Cooling System . . . . . . . . . . . . . . . . . . . . . 354 ▫ Front Turn Signal/Parking Lamp . . . . . . . . . 379 ▫ Brake System . . . . . . . . . . . . . . . . . . . . . . . 360 ▫ Front Fog Lamp . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 335 ENGINE COMPARTMENT — 2.
MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT — 2.
MAINTAINING YOUR VEHICLE 337 ENGINE COMPARTMENT — 3.
MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated Onboard Diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transaxle control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as maintaining engine emissions well within current government regulations.
MAINTAINING YOUR VEHICLE the gas cap is properly tightened. Press the trip odometer “Reset” button to turn off the message. If the problem persists, the message will appear the next time the vehicle is started. This might indicate a damaged cap. If the problem is detected twice in a row, the system will turn on the “Malfunction Indicator Light (MIL).” Resolving the problem will turn the MIL light off. 339 Normally, the OBD II system will be ready.
MAINTAINING YOUR VEHICLE 5. Approximately 15 seconds later, one of two things will Regardless of whether your vehicle’s OBD II system is happen: ready or not, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced a. The MIL will flash for about 10 seconds and then before going to the I/M station. The I/M station can fail return to being fully illuminated until you turn OFF your vehicle because the MIL is on with the engine the ignition or start the engine.
MAINTAINING YOUR VEHICLE DEALER SERVICE Your authorized dealer has the qualified service personnel, special tools, and equipment to perform all service operations in an expert manner. Service Manuals are available which include detailed service information for your vehicle. Refer to these manuals before attempting any procedure yourself. NOTE: Intentional tampering with emissions control systems may void your warranty and could result in civil penalties being assessed against you.
MAINTAINING YOUR VEHICLE CAUTION! (Continued) • Your vehicle has been built with improved fluids that protect the performance and durability of your vehicle and also allow extended maintenance intervals. Do not use chemical flushes in these components as the chemicals can damage your engine, transmission, power steering or air conditioning. Such damage is not covered by the New Vehicle Limited Warranty.
MAINTAINING YOUR VEHICLE CAUTION! Do not overfill the engine. Overfilling the engine will cause oil aeration, which can lead to loss of oil pressure and an increase in oil temperature. This could damage your engine. 343 Engine Oil Selection For best performance and maximum protection under all types of operating conditions, the manufacturer recommends engine oils that are API Certified and meet the requirements of Chrysler Material Standard MS-6395.
MAINTAINING YOUR VEHICLE CAUTION! Do not use chemical flushes in your engine oil as the chemicals can damage your engine. Such damage is not covered by the New Vehicle Limited Warranty. Engine Oil Viscosity (SAE Grade) — 2.4L and 2.7L Engines SAE 5W-20 engine oil is recommended for all operating temperatures. This engine oil improves low temperature starting and vehicle fuel economy. Your engine oil filler cap also shows the recommended engine oil viscosity for your vehicle.
MAINTAINING YOUR VEHICLE Synthetic Engine Oils You may use synthetic engine oils provided the recommended oil quality requirements are met, and the recommended maintenance intervals for oil and filter changes are followed. Materials Added to Engine Oils The manufacturer strongly recommends against the addition of any additives (other than leak detection dyes) to the engine oil. Engine oil is an engineered product and it’s performance may be impaired by supplemental additives.
MAINTAINING YOUR VEHICLE Engine Air Cleaner Filter WARNING! The air induction system (air cleaner, hoses, etc.) can provide a measure of protection in the case of engine backfire. Do not remove the air induction system (air cleaner, hoses, etc.) unless such removal is necessary for repair or maintenance. Make sure that no one is near the engine compartment before starting the vehicle with the air induction system (air cleaner, hoses, etc.) removed.
MAINTAINING YOUR VEHICLE 347 WARNING! CAUTION! • Battery fluid is a corrosive acid solution and can burn or even blind you. Do not allow battery fluid to contact your eyes, skin, or clothing. Do not lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area immediately with large amounts of water. • Battery gas is flammable and explosive. Keep flame or sparks away from the battery.
MAINTAINING YOUR VEHICLE Air Conditioner Maintenance For best possible performance, your air conditioner should be checked and serviced by an authorized dealer at the start of each warm season. This service should include cleaning of the condenser fins and a performance test. CAUTION! Do not use chemical flushes in your air conditioning system as the chemicals can damage your air conditioning components. Such damage is not covered by the New Vehicle Limited Warranty.
MAINTAINING YOUR VEHICLE Refrigerant Recovery and Recycling R-134a air conditioning refrigerant is a hydrofluorocarbon (HFC) that is endorsed by the Environmental Protection Agency and is an ozone-saving product. However, the manufacturer recommends that air conditioning service be performed by authorized dealers or other service facilities using recovery and recycling equipment. 349 The A/C Air Filter is located in the fresh air inlet behind the glove box.
MAINTAINING YOUR VEHICLE 5. Disengage the two retaining tabs that secure the filter 7. Install the A/C Air Filter with the arrow on the filter cover to the HVAC housing and remove the cover. pointing toward the floor. When installing the filter cover, make sure the retaining tabs fully engage the cover. CAUTION! The A/C Air Filter is labeled with an arrow to indicate airflow direction through the filter. Failure to install the filter properly will result in the need to replace it more often. 8.
MAINTAINING YOUR VEHICLE quiet, easy operation and to protect against rust and wear. Prior to the application of any lubricant, the parts concerned should be wiped clean to remove dust and grit; after lubricating excess oil and grease should be removed. Particular attention should also be given to hood latching components to ensure proper function. When performing other underhood services, the hood latch, release mechanism and safety catch should be cleaned and lubricated.
MAINTAINING YOUR VEHICLE present please proceed to clean wiper blades with humid Exhaust System cloth removing any debris that may be affecting its The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust function. system. Adding Washer Fluid The fluid reservoir for the windshield washers is located If you notice a change in the sound of the exhaust system in the engine compartment.
MAINTAINING YOUR VEHICLE WARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO) which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing CO, refer to Exhaust Gas in the Safety Tips section of this manual. CAUTION! The catalytic converter requires the use of unleaded fuel only.
MAINTAINING YOUR VEHICLE NOTE: Intentional tampering with emissions control To minimize the possibility of catalyst damage: systems can result in civil penalties being assessed • Do not shut off the engine or interrupt the ignition against you. when the transaxle is in gear and the vehicle is in motion. WARNING! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your exhaust system.
MAINTAINING YOUR VEHICLE WARNING! (Continued) • You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator. If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool. Never try to open a cooling system pressure cap when the radiator is hot. 355 Check the coolant recovery bottle tubing for brittle rubber, cracking, tears, cuts, and tightness of the connection at the bottle and radiator.
MAINTAINING YOUR VEHICLE CAUTION! CAUTION! (Continued) • Mixing of engine coolant (antifreeze) other than specified HOAT engine coolant (antifreeze), may result in engine damage and may decrease corrosion protection. If a non-HOAT engine coolant (antifreeze) is introduced into the cooling system in an emergency, it should be replaced with the specified engine coolant (antifreeze) as soon as possible. • Do not use water alone or alcohol-based engine coolant (antifreeze) products.
MAINTAINING YOUR VEHICLE 357 Please note that it is the owner’s responsibility to maintain the proper level of protection against freezing ac• The manufacturer recommends using MOPAR威 cording to the temperatures occurring in the area where Antifreeze/Coolant 5 Year/100,000 Mile Formula the vehicle is operated. HOAT (Hybrid Organic Additive Technology) or NOTE: Mixing engine coolant (antifreeze) types will equivalent.
MAINTAINING YOUR VEHICLE WARNING! rules for your community. To prevent ingestion by animals or children, do not store ethylene glycol based engine coolant (antifreeze) in open containers or allow it to remain in puddles on the ground. If ingested by a child or pet, seek emergency assistance immediately. Clean up any ground spills immediately. • The warning words “DO NOT OPEN HOT” on the cooling system pressure cap are a safety precaution.
MAINTAINING YOUR VEHICLE The radiator normally remains completely full, so there is no need to remove the radiator cap unless checking for engine coolant (antifreeze) freeze point or replacing coolant. Advise your service attendant of this. As long as the engine operating temperature is satisfactory, the coolant bottle need only be checked once a month. When additional engine coolant (antifreeze) is needed to maintain the proper level, it should be added to the coolant bottle. Do not overfill.
MAINTAINING YOUR VEHICLE • Make sure that the radiator and coolant recovery bottle overflow hoses are not kinked or obstructed. • Keep the front of the radiator clean. If your vehicle is equipped with air conditioning, keep the front of the condenser clean. WARNING! Riding the brakes can lead to brake failure and possibly an accident. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage.
MAINTAINING YOUR VEHICLE Clean the top of the master cylinder area before removing the cap. If necessary, add fluid to bring the fluid level up to the requirements described on the brake fluid reservoir. Overfilling of fluid is not recommended because it may cause leaking in the system. Fluid level can be expected to fall as the brake pads wear. Brake fluid level should be checked when pads are replaced. However, low fluid level may be caused by a leak and a checkup may be needed.
MAINTAINING YOUR VEHICLE WARNING! (Continued) WARNING! (Continued) • To avoid contamination from foreign matter or moisture, use only new brake fluid or fluid that has been in a tightly closed container. Keep the master cylinder reservoir cap secured at all times. Brake fluid in a open container absorbs moisture from the air resulting in a lower boiling point. This may cause it to boil unexpectedly during hard or prolonged braking, resulting in sudden brake failure. This could result in a accident.
MAINTAINING YOUR VEHICLE 363 driven at least 15 miles (24 km). Hot fluid cannot be held Fluid Level Check — Vehicles with 2.4L and 2.7L comfortably between the fingertips. Cold fluid is at a Engines Use the following procedure to check the automatic temperature below 80°F (27° C). transaxle fluid level properly: 7. Wipe the dipstick clean and reinsert until seated. Then, 1. Park the vehicle on level ground. remove dipstick and note the reading. 2.
MAINTAINING YOUR VEHICLE CAUTION! • Using a transmission fluid other than the manufacturer’s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder. Using a transmission fluid other than that recommended by the manufacturer will result in more frequent fluid and filter changes. Refer to “Fluids, Lubricants, and Genuine Parts” for the correct fluid type. • Dirt and water in the transaxle can cause serious damage.
MAINTAINING YOUR VEHICLE CAUTION! Do not use chemical flushes in your transmission as the chemicals can damage your transmission components. Such damage is not covered by the New Vehicle Limited Warranty. 365 The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle. What Causes Corrosion? Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle.
MAINTAINING YOUR VEHICLE Washing • Wash your vehicle regularly. Always wash your vehicle in the shade using MOPAR威 Car Wash or equivalent, or a mild car wash soap, and rinse the panels completely with clear water. CAUTION! Do not use abrasive or strong cleaning materials such as steel wool or scouring powder, which will scratch metal and painted surfaces.
MAINTAINING YOUR VEHICLE 367 • If your vehicle is damaged due to an accident or similar cause which destroys the paint and protective coating, have your vehicle repaired as soon as possible. The cost of such repairs is considered the responsibility of the owner. heavy soil and/or excessive brake dust, use MOPAR威 Wheel Cleaner or equivalent or select a nonabrasive, non-acidic cleaner. Do not use scouring pads, steel wool, a bristle brush, or metal polishes. Only MOPAR威 or equivalent is recommended.
MAINTAINING YOUR VEHICLE Do not use abrasive cleaning components, solvents, steel • Do not use any harsh solvents or any other form of wool or other aggressive material to clean the lenses. protectants on Stain Repel products. Stain Repel Fabric Cleaning Procedure — If Interior Care Equipped Instrument Panel Cover Stain Repel seats may be cleaned in the following manThe instrument panel cover has a low glare surface, ner: which minimizes reflections in the windshield.
MAINTAINING YOUR VEHICLE Cleaning Leather Upholstery MOPAR威 Total Clean or equivalent is specifically recommended for leather upholstery. Your leather upholstery can be best preserved by regular cleaning with a damp soft cloth. Small particles of dirt can act as an abrasive and damage the leather upholstery and should be removed promptly with a damp cloth. Stubborn soils can be removed easily with a soft cloth and MOPAR威 Total Clean or equivalent.
MAINTAINING YOUR VEHICLE Replace the belts if they appear frayed or worn or if the Cleaning Plastic Instrument Cluster Lenses The lenses in front of the instruments in this vehicle are buckles do not work properly. molded in clear plastic. When cleaning the lenses, care Dry with a soft tissue. must be taken to avoid scratching the plastic. Cleaning Center Console Cupholders 1. Clean with a wet, soft rag.
MAINTAINING YOUR VEHICLE 371 Installation Align the liner in the cupholder and press down firmly. FUSES Totally Integrated Power Module (TIPM) The TIPM is located in the engine compartment near the air cleaner assembly. This center contains cartridge fuses and mini fuses. A label that identifies each component may be printed on the inside of the cover. Refer to the graphic below for FUSES/TIPM location.
MAINTAINING YOUR VEHICLE Cavity 1 2 Cartridge Fuse 40 Amp Green — 3 — 4 — 5 — 6 — Mini Fuse Description — Power Top Module (If Equipped) 7 — 20 Amp Yellow AWD Module 8 — 9 40 Amp Green 10 — 11 — 12 — 10 Amp Red 10 Amp Red 20 Amp Yellow 10 Amp Red Battery Feed — Center High Mounted Stop Light (CHMSL)/ Brake Switch Battery Feed — Ignition Switch Trailer Tow — If Equipped Ignition Off Draw (IOD) — Power Mirror Switch/ Climate Controls Cavity Cartridge Fuse Mini Fuse 30 Amp
MAINTAINING YOUR VEHICLE Cavity 13 Cartridge Fuse — Mini Fuse 20 Amp Yellow 14 — 10 Amp Red 15 40 Amp Green — 16 — 15 Amp Lt. Blue Description Cavity Cartridge Fuse Mini Fuse — Ignition Off Draw (IOD) — Cabin Compartment Node (CCN)/ Interior Lighting Battery Feed — Radiator Fan Relay IGN Run/ACC — Cigar Lighter/PWR Sunroof Mod 17 — 10 Amp Red 18 40 Amp Green — 19 — 20 Amp Yellow 20 — 21 — 15 Amp Lt.
MAINTAINING YOUR VEHICLE Cavity 22 Cartridge Fuse Mini Fuse — 10 Amp Red 23 — 24 — 15 Amp Lt. Blue 25 Amp Natural 25 — 10 Amp Red 26 — 15 Amp Lt.
MAINTAINING YOUR VEHICLE Cavity Cartridge Fuse Mini Fuse 10 Amp Red 31 — 32 30 Amp Pink — 33 — 10 Amp Red 34 30 Amp Pink — Description Cavity Cartridge Fuse Mini Fuse — Auto Shutdown (ASD) Relay Feed 1 Battery Feed — Switch Bank/ Diagnostic Link Connector/ Powertrain Control Module (PCM) Battery Feed — Anti-Lock Brakes (ABS) Module - if equipped/ Electronic Stability Program (ESP) Module - If Equipped 35 40 Amp Green — 375 Description Battery Feed — Anti-Lock Brakes (ABS) Module - If
MAINTAINING YOUR VEHICLE Cavity Cartridge Fuse Mini Fuse 36 30 Amp Pink — 37 — 25 Amp Natural Description Battery Feed — Passenger Door Module (PDM)/ Driver Door Module (DDM) Power Top Module (If Equipped) CAUTION! • When installing the Totally Integrated Power Module cover, it is important to ensure the cover is properly positioned and fully latched. Failure to do so may allow water to get into the Totally Integrated Power Module, and possibly result in an electrical system failure.
MAINTAINING YOUR VEHICLE REPLACEMENT BULBS All the inside bulbs are brass or glass wedge base. Aluminum base bulbs are not approved and should not be used for replacement. 377 Front Park/Turn Signal/Side Marker Lamp . . . . 3757A Front Fog Lamp . . . . . . . . . . . . . . . . . . . . . . PSX24W Center High Mounted Stop (CHMSL) Lamp. . . . . . . . . . . . . . . . . . . . . . . . . . . W16W (921) Rear Tail/Stop Lamp . . . . . . . . . . . . . . . . . . . . . 3157 Rear Turn Signal Lamp. . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 2. Reach into engine compartment and from behind the 3. Rotate bulb and connector one-quarter turn and pull lamp assembly and grasp the connector. outward from assembly. CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life.
MAINTAINING YOUR VEHICLE 4. Pull the bulb out of the socket and replace the bulb. 379 Front Turn Signal/Parking Lamp 1. Raise and prop open the hood. 2. Rotate the bulb’s electrical connector one-quarter turn counterclockwise and remove it from the headlamp housing. 5. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol. 6. Reinsert the bulb and socket assembly and rotate clockwise one-quarter turn to secure.
MAINTAINING YOUR VEHICLE 3. Remove the bulb from the connector socket and install the replacement bulb. 4. Install the bulb and connector assembly into the headlamp housing and rotate the connector one-quarter turn clockwise to lock it in place. Front Fog Lamp NOTE: Access to the lamps through the lower fascia cutout is limited. We recommend you access the lamps by turning the steering wheel to allow access and remove the inner fender shield. 1.
MAINTAINING YOUR VEHICLE 381 CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with an oily surface, clean the bulb with rubbing alcohol. 3. Install the bulb and connector assembly into the fog lamp housing and rotate the connector one-quarter turn clockwise to lock it in place. Tail/Stop, Rear Turn Signal and Backup Lamps The taillamps are a two piece design.
MAINTAINING YOUR VEHICLE Changing the Tail/Stop Lamp or Rear Turn Signal Lamp 2. Remove the two plastic wing nuts from the taillamp housing. 1. Open the trunk and gently pull back the trunk liner behind the taillamp 3. Grasp the taillamp housing and pull it firmly outward while pushing gently on the studs from inside to disengage the housing from the vehicle.
MAINTAINING YOUR VEHICLE 383 4. Rotate the applicable bulb’s electrical connector one- 5. Remove the bulb from the connector socket and install quarter turn counterclockwise and remove it from the the replacement bulb. taillamp housing. 6. Install the bulb and connector assembly into the taillamp housing and rotate the connector one-quarter turn clockwise to lock it in place. 7. Reinstall the taillamp housing.
MAINTAINING YOUR VEHICLE Changing the Backup Lamp 1. Open the trunk. 4. Install the bulb and connector assembly into the housing and rotate the connector one-quarter turn clockwise to lock it in place. 2. Rotate the bulb’s electrical connector one-quarter turn License Plate Lamp counterclockwise and remove it from the housing. 1. Remove two retaining screws holding the lamp lens in place. 1 — Rear Fog Lamp 2 — Backup Lamp 3.
MAINTAINING YOUR VEHICLE 385 2. Gently pry the lens loose. 3. Pull bulb from socket, replace and reattach the lamp lens with the two retaining screws. Center High-Mounted Stop Lamp (CHMSL) 1. Open the trunk lid. 2. Rotate the bulb’s electrical connector one-quarter turn counterclockwise and remove it from the CHMSL housing. 3. Remove the bulb from the connector socket and install the replacement bulb. 4.
MAINTAINING YOUR VEHICLE FLUIDS AND CAPACITIES U.S. Fuel (Approximate) All Engines — (Except 2.4L PZEV) 16.9 Gallons 2.4L PZEV (Partial Zero Emissions Vehicle) 18.5 Gallons Engine Oil with Filter 2.4L Engine (SAE 5W-20, API Certified) 4.5 Quarts 2.7L Engine (SAE 5W-20, API Certified) 5.5 Quarts 3.5L Engine (SAE 10W-30, API Certified) 5.5 Quarts Cooling System* 2.4L Engine (MOPAR威Antifreeze/Coolant 5 7.7 Quarts Year/100,000 Mile Formula or equivalent) 2.7L Engine (MOPAR威 Antifreeze/Coolant 5 9.
MAINTAINING YOUR VEHICLE 387 FLUIDS, LUBRICANTS, AND GENUINE PARTS Engine Component Fluid, Lubricant, or Genuine Part MOPAR威 Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT Engine Coolant (Hybrid Organic Additive Technology) or equivalent. Use API Certified SAE 5W-20 Engine Oil, meeting the requirements of Chrysler Material Standard MS-6395. Refer to your engine oil filler Engine Oil (2.4L and 2.7L Engines) cap for correct SAE grade.
MAINTAINING YOUR VEHICLE Chassis Component Automatic Transaxle Brake Master Cylinder Power Steering Reservoir Fluid, Lubricant, or Genuine Part MOPAR威 ATF+4 Automatic Transmission Fluid or equivalent. MOPAR威 DOT 3 and SAE J1703 should be used. If DOT 3 brake fluid is not available, then DOT 4 is acceptable. Use only recommended brake fluids. MOPAR威 Power Steering Fluid +4, MOPAR威 ATF+4 Automatic Transmission Fluid or equivalent.
M A I N T E N A N C ▫ Required Maintenance Intervals . . . . . . . . . . 392 E MAINTENANCE SCHEDULES CONTENTS 䡵 Emissions Control System Maintenance . . . . . . 390 䡵 Maintenance Schedule . . . . . . . . . . . . . . . . . .
M A I N T E N A N C E 390 MAINTENANCE SCHEDULES EMISSIONS CONTROL SYSTEM MAINTENANCE The Scheduled Maintenance services listed in bold type must be done at the times or mileages specified to ensure the continued proper functioning of the emissions control system. These and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
MAINTENANCE SCHEDULES NOTE: • The oil change indicator message will not monitor the time since the last oil change. Change your vehicles oil if it has been six months since your last oil change even if the oil change indicator message is NOT illuminated. • Change your engine oil more often if you drive your vehicle off-road for an extended period of time.
M A I N T E N A N C E 392 MAINTENANCE SCHEDULES Once a Month • Check tire pressure and look for unusual wear or damage. CAUTION! Failure to perform the required maintenance items may result in damage to the vehicle. • Inspect the battery and clean and tighten the terminals as required. Required Maintenance Intervals Refer to the Maintenance Schedules on the following • Check the fluid levels of coolant reservoir, brake pages for the required maintenance intervals.
MAINTENANCE SCHEDULES 6,000 Miles (10,000 km) or 6 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. Odometer Reading Repair Order # Signature Authorized Chrysler Dealer Date Dealer Code 393 M 12,000 Miles (20,000 km) or 12 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle in dusty or off-road conditions, inspect the engine air cleaner filter, and replace if necessary.
M 394 MAINTENANCE SCHEDULES A I 18,000 Miles (30,000 km) or N T 18 Months Maintenance E Service Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate tires. C E 24,000 Miles (40,000 km) or 24 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle in dusty or off-road conditions, inspect the engine air cleaner filter, and replace if necessary. ❏ Inspect the brake linings, and replace as necessary.
MAINTENANCE SCHEDULES 30,000 Miles (50,000 km) or 30 Months Maintenance Service Schedule 36,000 Miles (60,000 km) or 36 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ Replace the engine air cleaner filter. ❏ Replace the spark plugs (2.4L Engine except PZEV*). Odometer Reading Repair Order # Signature Authorized Chrysler Dealer 395 M Date Dealer Code ❏ Change the engine oil and engine oil filter. ❏ Rotate tires.
M 396 MAINTENANCE SCHEDULES A I 42,000 Miles (70,000 km) or N T 42 Months Maintenance E Service Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate tires. C E 48,000 Miles (80,000 km) or 48 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle in dusty or off-road conditions, inspect the engine air cleaner filter, and replace if necessary. ❏ Inspect the brake linings, and replace as necessary.
MAINTENANCE SCHEDULES 54,000 Miles (90,000 km) or 54 Months Maintenance Service Schedule 60,000 Miles (100,000 km) or 60 Months Maintenance Service Schedule ❏ ❏ ❏ ❏ ❏ ❏ ❏ Change the engine oil and engine oil filter. Rotate tires. Replace the engine air cleaner filter. Replace the spark plugs (2.4L Engine except PZEV*). Inspect the brake linings, and replace as necessary. Replace the air conditioning filter (if equipped).
M 398 MAINTENANCE SCHEDULES A I 66,000 Miles (110,000 km) or N T 66 Months Maintenance E Service Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate tires. C E 72,000 Miles (120,000 km) or 72 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle in dusty or off-road conditions, inspect the engine air cleaner filter, and replace if necessary. ❏ Inspect the brake linings, and replace as necessary.
MAINTENANCE SCHEDULES 78,000 Miles (130,000 km) or 78 Months Maintenance Service Schedule 84,000 Miles (140,000 km) or 84 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle in dusty or off-road conditions, inspect the engine air cleaner filter, and replace if necessary. ❏ Inspect the brake linings, and replace as necessary. ❏ Replace the air conditioning filter (if equipped).
M 400 MAINTENANCE SCHEDULES A I 90,000 Miles (150,000 km) or N T 90 Months Maintenance E Service Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate tires. C ❏ Replace the engine air cleaner filter. E S C H E D U L E S 8 96,000 Miles (160,000 km) or 96 Months Maintenance Service Schedule ❏ Replace the spark plugs (2.4L Engine except PZEV*). ❏ Inspect and replace the PCV valve, if necessary†.
MAINTENANCE SCHEDULES 102,000 Miles (170,000 km) or 102 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ Replace the spark plugs (2.4L PZEV*, 2.7L and 3.5L Engines). ❏ Replace the timing belt (3.5L Engine). ❏ Flush and replace the engine coolant. ❏ Inspect accessory drive belt, replace if necessary.
M 402 MAINTENANCE SCHEDULES A I 114,000 Miles (190,000 km) or N T 114 Months Maintenance E Service Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate tires. C E S C H E D U L E S 8 Odometer Reading Repair Order # Signature Authorized Chrysler Dealer Date Dealer Code 120,000 Miles (200,000 km) or 120 Months Maintenance Service Schedule ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ Change the engine oil and engine oil filter. Rotate tires. Replace the engine air cleaner filter. Replace the spark plugs (2.
MAINTENANCE SCHEDULES 126,000 Miles (210,000 km) or 126 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. Odometer Reading Repair Order # Signature Authorized Chrysler Dealer Date Dealer Code 403 M 132,000 Miles (220,000 km) or 132 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle in dusty or off-road conditions, inspect the engine air cleaner filter, and replace if necessary.
M 404 MAINTENANCE SCHEDULES A I 138,000 Miles (230,000 km) or N T 138 Months Maintenance E Service Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate tires. C E S C H E D U L E S 8 Odometer Reading Repair Order # Signature Authorized Chrysler Dealer Date Dealer Code 144,000 Miles (240,000 km) or 144 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires.
MAINTENANCE SCHEDULES 150,000 Miles (250,000 km) or 150 Months Maintenance Service Schedule ❏ ❏ ❏ ❏ Change the engine oil and engine oil filter. Rotate tires. Replace the engine air cleaner filter. Replace the spark plugs (2.4L Engine except PZEV*). Odometer Reading Repair Order # Signature Authorized Chrysler Dealer Date Dealer Code 405 M A I N † This maintenance is recommended by the manufacturer T to the owner, but is not required to maintain emissions E N warranty.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS 䡵 Suggestions For Obtaining Service For Your Vehicle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 409 ▫ Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) . . . . . . . . . . . . 411 ▫ Prepare For The Appointment . . . . . . . . . . . 409 ▫ Service Contract . . . . . . . . . . . . . . . . . . . . . 411 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . 409 䡵 Warranty Information (U.S. Vehicles Only) . . . .
IF YOU NEED CONSUMER ASSISTANCE 䡵 Publication Order Forms . . . . . . . . . . . . . . . . 413 ▫ Traction Grades . . . . . . . . . . . . . . . . . . . . . 415 䡵 Department Of Transportation Uniform Tire Quality Grades . . . . . . . . . . . . . . . . . . . . . . . . 415 ▫ Temperature Grades . . . . . . . . . . . . . . . . . . 416 ▫ Treadwear . . . . . . . . . . . . . . . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE 409 the service advisor and list the items in order of priority. At many authorized dealers, you may obtain a rental vehicle at a minimal daily charge. If you need a rental, it Prepare For The Appointment is advisable to make these arrangements when you call If you’re having warranty work done, be sure to have the for an appointment. right papers with you. Take your warranty folder. All work to be performed may not be covered by the IF YOU NEED ASSISTANCE warranty.
IF YOU NEED CONSUMER ASSISTANCE This is why you should always talk to an authorized • Vehicle delivery date and mileage dealer’s service manager first. Most matters can be reChrysler Group LLC Customer Center solved with this process. P.O. Box 21–8004 • If for some reason you are still not satisfied, talk to the Auburn Hills, MI 48321–8004 general manager or owner of the authorized dealer- Phone: (800) 992-1997 ship. They want to know if you need assistance. Chrysler Canada Inc.
IF YOU NEED CONSUMER ASSISTANCE Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommunication Devices for the Deaf) equipment at its customer center. Any hearing or speech impaired customer, who has access to a TDD or a conventional teletypewriter (TTY) in the United States, can communicate with the manufacturer by dialing 1–800–380–CHRY.
IF YOU NEED CONSUMER ASSISTANCE We appreciate that you have made a major investment when you purchased the vehicle. An authorized dealer has also made a major investment in facilities, tools, and training to assure that you are absolutely delighted with the ownership experience. You’ll be pleased with their sincere efforts to resolve any warranty issues or related concerns.
IF YOU NEED CONSUMER ASSISTANCE If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your authorized dealer, and the manufacturer. 413 Transport Canada, Motor Vehicle Defect Investigations and Recalls, 2780 Sheffield Road, Ottawa, Ontario K1B 3V9.
IF YOU NEED CONSUMER ASSISTANCE vehicle, system, and/or components is written in • Owner’s Manuals straightforward language with illustrations, diagrams, These Owner’s Manuals have been prepared with the and charts. assistance of service and engineering specialists to • Diagnostic Procedure Manuals acquaint you with specific Chrysler Group LLC vehicles.
IF YOU NEED CONSUMER ASSISTANCE DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES The following tire grading categories were established by the National Highway Traffic Safety Administration. The specific grade rating assigned by the tire’s manufacturer in each category is shown on the sidewall of the tires on your vehicle. 415 significantly from the norm due to variations in driving habits, service practices, and differences in road characteristics and climate.
IF YOU NEED CONSUMER ASSISTANCE Temperature Grades The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
INDEX 10
INDEX About Your Brakes . . . . . . . . . . . . . . . . . . . . . . . 252 ABS (Anti-Lock Brake System) . . . . . . . . . . . . . . 254 Adding Engine Coolant (Antifreeze) . . . . . . . . . . 356 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 299 Adding Washer Fluid . . . . . . . . . . . . . . . . . . . . . 352 Additives, Fuel . . . . . . . . . . . . . . . . . . . . . . . . . 293 Air Cleaner, Engine (Engine Air Cleaner Filter) . . . 346 Air Conditioner Maintenance . . . . . . . . . .
INDEX 419 Body Mechanism Lubrication . . . . . . . . . . . . . . . 350 B-Pillar Location . . . . . . . . . . . . . . . . . . . . . . . . 268 Brake Assist System . . . . . . . . . . . . . . . . . . . . . . 257 Brake, Parking . . . . . . . . . . . . . . . . . . . . . . . . . . 252 Brake System . . . . . . . . . . . . . . . . . . . . . . . . . . . 360 Anti-Lock (ABS) . . . . . . . . . . . . . . . . . . . . . . . 254 Fluid Check . . . . . . . . . . . . . . . . . . . . . . . 360,388 Master Cylinder . . . . . .
INDEX Caps, Filler Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 299 Oil (Engine) . . . . . . . . . . . . . . . . . . 335,336,337,344 Power Steering . . . . . . . . . . . . . . . . . . . . . . . . 251 Radiator (Coolant Pressure) . . . . . . . . . . . . . . . 357 Car Washes . . . . . . . . . . . . . . . . . . . . . . . . . . . . 366 Carbon Monoxide Warning . . . . . . . . . . . . . . . 82,294 Cargo Area Features . . . . . . . . . . . . . . . . . . . . . . 134 Cargo Compartment . .
INDEX Console, Floor . . . . . . . . . . . . . . . . . . . . . . . 104,136 Contract, Service . . . . . . . . . . . . . . . . . . . . . . . . 411 Coolant Pressure Cap (Radiator Cap) . . . . . . . . . . 357 Cooling System . . . . . . . . . . . . . . . . . . . . . . . . . 354 Adding Coolant (Antifreeze) . . . . . . . . . . . . . . 356 Coolant Capacity . . . . . . . . . . . . . . . . . . . . . . 386 Coolant Level . . . . . . . . . . . . . . . . . . . . . . 355,358 Disposal of Used Coolant . . . . . . . . . . .
INDEX Door Locks, Automatic . . . . . . . . . . . . . . . . . . . . 30 Emergency Trunk Release . . . . . . . . . . . . . . . . . 37,38 Door Opener, Garage . . . . . . . . . . . . . . . . . . . . . 120 Emission Control System Maintenance . . . . . . 339,390 Engine . . . . . . . . . . . . . . . . . . . . . . . . . . 335,336,337 Driving Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . 346 On Slippery Surfaces . . . . . . . . . . . . . . . . . . . 247 Block Heater . . . . . . . . . . . . .
INDEX 423 Automatic Transaxle . . . . . . . . . . . . . . . . . . . . 364 Oil Selection . . . . . . . . . . . . . . . . . . . . . . . 343,386 Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . 345,387 Oil Synthetic . . . . . . . . . . . . . . . . . . . . . . . . . 345 Engine Oil Disposal . . . . . . . . . . . . . . . . . . . . 345 Overheating . . . . . . . . . . . . . . . . . . . . . . . . . . 316 Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 235 Flashers . . . . . . . . . . .
INDEX Fluid Level Checks Automatic Transaxle . . . . . . . . . . . . . . . . . 363,364 Brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . 360,388 Cooling System . . . . . . . . . . . . . . . . . . . . . . . 355 Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . 342 Power Steering . . . . . . . . . . . . . . . . . . . . . 251,388 Fluids . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 387 Fluids, Lubricants and Genuine Parts . . . . . . . . . .
INDEX 425 Head Restraints . . . . . . . . . . . . . . . . . . . . . . . . . . 98 Headlights . . . . . . . . . . . . . . . . . . . . . . . . . . . . 377 Bulb Replacement . . . . . . . . . . . . . . . . . . . . . . 377 Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . 367 High Beam . . . . . . . . . . . . . . . . . . . . . . . . 109,159 High Beam/Low Beam Select Switch . . . . . . . . 109 On With Wipers . . . . . . . . . . . . . . . . . . . . . . . 115 Passing . . . . . . . . . . . . . . . .
INDEX Ignition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Ignition Key Removal . . . . . . . . . . . . . . . . . . . . . 12 Illuminated Entry . . . . . . . . . . . . . . . . . . . . . . . . 20 Immobilizer (Sentry Key) . . . . . . . . . . . . . . . . . . . 15 Infant Restraint . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Latches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84 Hood . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104 Lead Free Gasoline . . . . . . . . . . . . . . . . . . . . . . 290 Leaks, Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84 Life of Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . 278 Light Bulbs . . . . . . . . . . . . . . . . . . . . . . . . . . 84,377 Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Malfunction Indicator Light (Check Engine) . . 157,339 Manual, Service . . . . . . . . . . . . . . . . . . . . . . . . . 413 Map/Reading Lights . . . . . . . . . . . . . . . . . . . . . 111 Master Cylinder (Brakes) . . . . . . . . . . . . . . . . . . 360 Methanol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 291 Mini-Trip Computer . . . . . . . . . . . . . . . . . . . . . . 162 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 Automatic Dimming . . . . . . .
INDEX Occupant Restraints . . . . . . . . . . . . . . . . . . . . . 61,65 Occupant Restraints (Sedan) . . . . . . . . . 39,57,58,61,64 Octane Rating, Gasoline (Fuel) . . . . . . . . . . . . . . 290 Odometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150 Trip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150,153 Oil Change Indicator . . . . . . . . . . . . . . . . 152,162,390 Oil Change Indicator, Reset . . . . . . . . . . . . . . 152,162 Oil, Engine . . . . . . . . . . . . . . .
INDEX Phone, Hands-Free (uconnect威) . . . . . . . . . . . . . . . 93 Placard, Tire and Loading Information . . . . . . . . . 268 Power Deck Lid Release . . . . . . . . . . . . . . . . . . . . . . . 37 Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 Outlet (Auxiliary Electrical Outlet) . . . . . . . . . . 129 Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97 Steering . . . . . . . . . . . .
INDEX Remote Sound System (Radio) Controls . . . . . . . . 215 Remote Starting System . . . . . . . . . . . . . . . . . . . . 26 Remote Trunk Release . . . . . . . . . . . . . . . . . . . . . 37 Replacement Bulbs . . . . . . . . . . . . . . . . . . . . . . . 377 Replacement Keys . . . . . . . . . . . . . . . . . . . . . . . . 16 Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . 340 Replacement Tires . . . . . . . . . . . . . . . . . . . . . . . 278 Reporting Safety Defects . . . . . . . . . .
INDEX Untwisting Procedure . . . . . . . . . . . . . . . . . . . . 46 Seat Belts (Sedan) . . . . . . . . . . . . . . . . . . . . . . . . 39 Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94 Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . 94 Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104 Heated . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101 Lumbar Support . . . . . . . . . . . . . . . . . . . . . . . 97 Power . . . . . . . .
INDEX Starting Procedures . . . . . . . . . . . . . . . . . . . . . . 235 Steering Power . . . . . . . . . . . . . . . . . . . . . . . . . . . 250,251 Tilt Column . . . . . . . . . . . . . . . . . . . . . . . . . . 116 Wheel, Tilt . . . . . . . . . . . . . . . . . . . . . . . . . . . 116 Steering Wheel Mounted Sound System Controls . . . . . . . . . . . . . . . . . . . . . . . . . 215 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134,376 Storage, Vehicle . . . . . . . . . . . . . . . . .
INDEX Life of Tires . . . . . . . . . . . . . . . . . . . . . . . . . . 278 Load Capacity . . . . . . . . . . . . . . . . . . . . . . . . 268 Pressure Monitor System (TPMS) . . . . . . . . . . . 281 Pressure Warning Light . . . . . . . . . . . . . . . . . . 156 Quality Grading . . . . . . . . . . . . . . . . . . . . . . . 415 Radial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 275 Replacement . . . . . . . . . . . . . . . . . . . . . . . . . 278 Rotation . . . . . . . . . . . . . . . .
INDEX Transmitter Battery Service (Remote Keyless Entry) . . . . . . . . . . . . . . . . . . . . 25 Transmitter, Garage Door Opener (HomeLink威) . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 Transmitter Programming (Remote Keyless Entry) . . . . . . . . . . . . . . . . . . . . 25 Transporting Pets . . . . . . . . . . . . . . . . . . . . . . . . 81 Tread Wear Indicators . . . . . . . . . . . . . . . . . . . . 277 Trip Odometer . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Warnings and Cautions . . . . . . . . . . . . . . . . . . . . . 6 Warranty Information . . . . . . . . . . . . . . . . . . . . . 412 Washer, Adding Fluid . . . . . . . . . . . . . . . . . . . . . 352 Washers, Windshield . . . . . . . . . . . . . . . . 112,115,352 Washing Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . 366 Water Driving Through . . . . . . . . . . . . . . . . . . . . . . 248 Wheel and Wheel Trim . . . . . . . . . . . . . . . . . . . . 367 Wheel and Wheel Trim Care . . .
