2010 OWNER’ S MANUAL 300
SECTION TABLE OF CONTENTS PAGE 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 2 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85 3 4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION 1 CONTENTS 䡵 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 Vehicle Identification Number .............. 6 䡵 How To Use This Manual . . . . . . . . . . . . . . . . . . 4 䡵 Vehicle Modifications/Alterations . . . . . . . . . . . . 7 䡵 Warnings And Cautions . . . . . . . . . . . . . . . . . . .
4 INTRODUCTION INTRODUCTION Congratulations on selecting your new Chrysler Group LLC vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. This Owner’s Manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your vehicle.
INTRODUCTION 5 1
6 INTRODUCTION WARNINGS AND CAUTIONS This Owner’s Manual contains WARNINGS against operating procedures that could result in an accident or bodily injury. It also contains CAUTIONS against procedures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important information. Observe all Warnings and Cautions. VEHICLE IDENTIFICATION NUMBER The Vehicle Identification Number (VIN) is on the left front corner of the instrument panel.
INTRODUCTION 7 VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS 䡵 A Word About Your Keys . . . . . . . . . . . . . . . . . 12 䡵 Vehicle Security Alarm — If Equipped . . . . . . . . 18 ▫ Wireless Ignition Node (WIN) . . . . . . . . . . . . 12 ▫ Rearming Of The System . . . . . . . . . . . . . . . . 18 ▫ Key FOB . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 ▫ To Arm The System . . . . . . . . . . . . . . . . . . . 18 ▫ Removing Key FOB From Ignition . . . . . . . . . 14 ▫ To Disarm The System . . .
10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Using The Panic Alarm . . . . . . . . . . . . . . . . . 25 ▫ Programming Additional Transmitters . . . . . . 25 ▫ Wind Buffeting . . . . . . . . . . . . . . . . . . . . . . . 43 䡵 Trunk Lock And Release . . . . . . . . . . . . . . . . . 43 ▫ Transmitter Battery Replacement . . . . . . . . . . 26 䡵 Trunk Safety Warning . . . . . . . . . . . . . . . . . . . 44 ▫ General Information . . . . . . . . . . . . . . . . . . . 27 ▫ Trunk Emergency Release . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Supplemental Restraint System (SRS) — Airbags . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 ▫ Airbag Deployment Sensors And Controls . . . 62 ▫ Event Data Recorder (EDR) . . . . . . . . . . . . . . 69 ▫ Child Restraints . . . . . . . . . . . . . . . . . . . . . . 71 䡵 Engine Break-In Recommendations . . . . . . . . . . 80 䡵 Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 11 ▫ Transporting Passengers . . . . . . . . . . . . .
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS Your vehicle uses a keyless ignition system. This system consists of a Key Fob with Remote Keyless Entry (RKE) transmitter and a Wireless Ignition Node (WIN) with integral ignition switch. You can insert the Key Fob into the ignition switch with either side up. Keyless Go Feature This vehicle may be equipped with the Keyless Go feature, refer to “Starting Procedure” in “Starting And Operating” for further information.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 Key Fob The Key Fob operates the ignition switch. It also contains the Remote Keyless Entry (RKE) transmitter and an emergency key, which stores in the rear of the Key Fob. NOTE: If your vehicle is equipped with Passive Entry/ Keyless Go (PEKG), the Key Fob will also contain a special receiver that communicates with the vehicle. Passive Entry/Keyless Go Key Fobs can only be used with Passive Entry/Keyless Go equipped vehicles.
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To remove the emergency key, slide the mechanical latch Removing Key Fob From Ignition at the top of the Key Fob sideways with your thumb and Place the shift lever in PARK. Turn the Key Fob to the OFF position and then remove the Key Fob. then pull the key out with your other hand. With the Passive Entry/Keyless Go system, the EVIC will display the ignition switch position “OFF/ACC/RUN”.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 and power outlets will remain active for up to 60 minCAUTION! utes after the ignition switch is placed in the OFF position. Opening either front door will cancel this An unlocked car is an invitation to thieves. Always feature. The time for this feature is programmable. remove the Key Fob from the ignition and lock all Refer to “Electronic Vehicle Information Center (EVIC) doors when leaving the vehicle unattended.
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE SENTRY KEY姞 The Sentry Key威 Immobilizer System prevents unauthorized vehicle operation by disabling the engine. The system does not need to be armed or activated. Operation is automatic, regardless of whether the vehicle is locked or unlocked. indicates that there is a problem with the electronics. This condition will result in the engine being shut off after two seconds.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 Duplication of Key Fobs may be performed at an authorized dealer, this procedure consists of programming a NOTE: Only Key Fobs that are programmed to the blank Key Fob to the vehicle electronics. A blank Key Fob vehicle electronics can be used to start and operate the is one that has never been programmed. vehicle. Once a Key Fob is programmed to a vehicle, it cannot be programmed to any other vehicle.
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • This device must accept any interference that may be received, including interference that may cause undesired operation. VEHICLE SECURITY ALARM — IF EQUIPPED The Vehicle Security Alarm monitors the vehicle doors for unauthorized entry and the ignition switch (and Keyless Go Start/Stop button) for unauthorized operation.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 the vehicle ignition is ⬙OFF⬙ (refer to “Starting Proce- • The Vehicle Security Alarm remains armed during dures” in “Starting And Operating” for further informatrunk entry. Pressing the TRUNK button will not tion). Then either press the power door LOCK switch disarm the Vehicle Security Alarm.
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE exterior lights will flash, the horn will sound, and the ILLUMINATED ENTRY — IF EQUIPPED ignition will not start the vehicle. If this occurs, disarm The courtesy lights will turn on when you use the Remote Keyless Entry (RKE) transmitter or unlock any the Vehicle Security Alarm. door.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Inserting the Key Fob with RKE transmitter into the ignition switch disables all buttons on that RKE transmitter; however, the buttons on the remaining RKE transmitters will continue to work. Driving at speeds 5 mph (8 km/h) and above disables all RKE transmitter buttons for all RKE transmitters.
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Settings (Customer-Programmable Features)” in “Un- NOTE: Pressing the LOCK button on the RKE transmitderstanding Your Instrument Panel” for further infor- ter while you are inside the vehicle will activate the security alarm. Opening a door with the Vehicle Security mation. Alarm armed will cause the alarm to sound. Press the • For vehicles not equipped with the EVIC, perform the UNLOCK button to deactivate the security alarm.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 • For vehicles not equipped with the EVIC, perform the alarm. Opening a door with the security alarm activated following procedure: will cause the alarm to sound. Press the UNLOCK button to deactivate the security alarm. 1. Press and hold the UNLOCK button on a programmed RKE transmitter for at least 4 seconds, but no longer than Turn Headlights On with Remote Key Unlock 10 seconds.
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Lock the Doors • For vehicles not equipped with the EVIC, perform the Press and release the LOCK button on the RKE transmitfollowing procedure: ter to lock all doors. The turn signal lights will flash and 1. Press the LOCK button on a programmed RKE transthe horn will chirp to acknowledge the signal. mitter for at least 4 seconds, but no longer than 10 secIf the vehicle is equipped with Passive Entry, refer to onds.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 alarm. Opening a door with the security alarm activated The Panic Alarm will stay on for three minutes unless will cause the alarm to sound. Press the UNLOCK button you turn it off by either pressing the PANIC button a second time or drive the vehicle at a speed of 15 mph to deactivate the security alarm. (24 km/h) or greater. To Unlatch the Trunk Press the TRUNK button on the RKE transmitter two NOTE: times within five seconds to unlatch the trunk.
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Transmitter Battery Replacement The recommended replacement battery is one CR2032 battery. NOTE: • Do not touch the battery terminals that are on the back housing or the printed circuit board. 1. Battery access is through a door located on the rear of the RKE transmitter. Insert a small, flat blade screwdriver into the slot and gently pry open the access door. Battery Replacement 1— Battery Access Door 2. Remove and replace the battery.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 3. Reposition the access door panel over the battery 1. A weak battery in the RKE transmitter. The expected life of the battery is a minimum of three years. opening and snap into place. 2. Closeness to a radio transmitter such as a radio station General Information This device complies with Part 15 of the FCC rules and tower, airport transmitter, and some mobile or CB radios. RSS 210 of Industry Canada.
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: For vehicles equipped with Keyless Go, the How to Use Remote Start All of the following conditions must be met before the remote start feature will operate with the Start/Stop button installed in the ignition switch.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Enter Remote Start Mode Press and release the REMOTE START button on the RKE transmitter twice, within five seconds. The parking lights will flash and the horn will chirp twice (if programmed). Then, the engine will start and the vehicle will remain in the Remote Start mode for a 15-minute cycle. NOTE: • The park lamps will turn on and remain on during Remote Start mode.
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Stop button is installed in the ignition switch, otherwise, DOOR LOCKS insert the Key Fob into the ignition switch and turn to the Manual Door Locks RUN position. Refer to the “Passive Entry System — If To lock each door, push the door lock plunger on each Equipped” under “Door Locks” for more information. door trim panel downward. To unlock each door, pull the door lock plunger on each door trim panel upward.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If the door lock plunger is down when you shut the door, the door will lock. Make sure the key is not inside the vehicle before closing the door. WARNING! • For personal security and safety in the event of an accident, lock the vehicle doors before you drive as well as when you park and leave the vehicle. • When leaving the vehicle, always remove the key from the ignition and lock your vehicle.
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE prevents you from accidentally locking the Key Fob in Power Door Locks A power door lock switch is on each front door trim the vehicle. Removing the Key Fob, returning the ignition panel. Use this switch to lock or unlock the doors. mode to the OFF position, or closing the door will allow the locks to operate. If a door is open, the Key Fob is in the ignition OFF or ACC position, a chime will sound as a reminder to remove the Key Fob.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. The throttle is pressed. 5. The vehicle speed is above 15 mph (24 km/h). 33 1. Close all doors and place the Key Fob in the ignition switch. 2. Cycle the ignition switch between OFF and RUN and 6. The doors were not previously locked using the power then back to OFF four times ending up in the OFF door lock switch or Remote Keyless Entry (RKE) position (do not start engine). transmitter. 3. Press the power door LOCK switch to lock the doors.
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Automatic Unlock Doors on Exit • For vehicles equipped with the EVIC, refer to “ElecThe doors will unlock automatically on vehicles with tronic Vehicle Information Center (EVIC)/Personal power door locks if: Settings (Customer-Programmable Features)” in “Understanding Your Instrument Panel” for further infor1. The Automatic Unlock Doors On Exit feature is enmation. abled. • For vehicles not equipped with the EVIC, perform the 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 5. Repeat these steps if you want to return this feature to • If a passive entry door handle has not been used for its previous setting. 72 hours the passive entry feature for that handle may time out. Also, if it has been raining on a passive entry NOTE: Use the Automatic Unlock Doors On Exit feature door handle for 24 hours, that door handle’s passive in accordance with local laws. entry feature may be deactivated.
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Door 1st Press” and “Unlock All Doors 1st Press”, refer to “Electronic Vehicle Information Center (EVIC)/Personal Settings (Customer-Programmable Features)” in “Understanding Your Instrument Panel” for further information. To Unlock From The Passenger Side: With a valid Passive Entry RKE transmitter within 5 ft (1.5 m) of the passenger side of the vehicle, grab the front passenger door handle to unlock all four doors automatically.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE deck lid, the deck lid will automatically unlatch, unless another one of the vehicle’s Passive Entry RKE transmitters is outside the vehicle and within 3 ft (1.0 m) of the deck lid. To Lock the Vehicle’s Doors The front door handles have LOCK buttons located on the outside of the handle, with one of the vehicle’s Passive Entry RKE transmitters within 5 ft (1.5 m) of the driver’s side, press the driver’s door handle LOCK button to lock all four doors.
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: For emergency key information, refer to “A NOTE: When the Child Protection Door Lock system is Word About Your Keys”. engaged, the door can be opened only by using the outside door handle even though the inside door lock is in the unlocked position. WARNING! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 • For emergency exit with the system engaged, move the door lock plunger to the UNLOCK position, roll down the window and open the door with the outside door handle. 2 To Disengage the Child Protection Door Lock System 1. Open the rear door. 2. Insert the tip of the emergency key (or similar object) into the child lock control and pull it downward. Child Lock Control 3. Repeat Steps 1 and 2 for the opposite rear door.
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE There are single window controls on each passenger door trim panel, which operate the passenger door windows. Power Windows The window controls will operate only when the ignition The window controls on the driver’s door control all the switch is in the ACC or RUN position. door windows.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Never leave children in a vehicle with the key in the ignition switch or leave a vehicle with Keyless Go in the ACC or RUN position. Occupants, particularly unattended children, can become entrapped by the windows while operating the power window switches. Such entrapment may result in serious injury or death. AUTO-Down Feature The driver door power window switch and some model passenger door power window switches have an AUTOdown feature.
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Any impact due to rough road conditions may trigger the auto-reverse function unexpectedly during autoclosure. If this happens, pull the switch lightly to the first detent and hold to close the window manually. WARNING! There is no anti-pinch protection when the window is almost closed. Be sure to clear all objects from the window before closing.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 1. Pull the window switch up to close window com- NOTE: The transmission must be in PARK before the pletely and continue to hold the switch up for an button will operate. additional two seconds after the window is closed.
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE With the ignition switch in the OFF position or the key Trunk Emergency Release removed from the ignition switch, the Trunk Open sym- The trunk of your vehicle is equipped with an emergency release handle. It is located on the inside of the trunk lid, bol will display until the trunk is closed. near the latch, and is coated so that it glows in a darkened Refer to “Passive Entry — If Equipped” under “Door trunk. Pull on the handle to open the trunk.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 If you will be carrying children too small for adult-sized OCCUPANT RESTRAINTS Some of the most important safety features in your seat belts, the seat belts or the Lower Anchors and Tether for CHildren (LATCH) feature can be used to hold infant vehicle are the restraint systems: and child restraint systems. For more information on • Three-point lap and shoulder belts for the driver and LATCH, see Lower Anchors and Tether for CHildren all passengers (LATCH).
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! In a collision, you and your passengers can suffer much greater injuries if you are not properly buckled up. You can strike the interior of your vehicle or other passengers, or you can be thrown out of the vehicle. Always be sure you and others in your vehicle are buckled up properly. ejection and the risk of injury caused by striking the inside of the vehicle. Everyone in a motor vehicle should be belted at all times.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 WARNING! WARNING! (Continued) • It is dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • Be sure everyone in your vehicle is in a seat and using a seat belt properly. • Wearing a seat belt incorrectly is dangerous.
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. The seat belt latch plate is above the back of your seat. 1. Enter the vehicle and close the door. Sit back and Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to make the belt adjust the front seat. go around your lap. Lap/Shoulder Belt Operating Instructions 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 WARNING! WARNING! (Continued) • A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you properly. In a sudden stop, you could move too far forward, increasing the possibility of injury. Wear your seat belt snugly.
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up a bit on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision. WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 6. To release the belt, push the red button on the buckle. above the webbing to release the anchorage, then move it The belt will automatically retract to its stowed position. up or down to the position that fits you best. If necessary, slide the latch plate down the webbing to allow the belt to retract fully. WARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection.
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE you will prefer a higher position. When you release the 4. Continue to slide the latch plate up until it clears the anchorage try to move it up and down to make sure that folded webbing. it is locked in position. Automatic Locking Retractors (ALR) Mode — If In the rear seat, move toward the center of the seat to Equipped In this mode, the shoulder belt is automatically preposition the belt away from your neck. locked.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 2. Grasp the shoulder portion and pull downward until NOTE: These devices are not a substitute for proper seat belt placement by the occupant. The seat belt still must be the entire belt is extracted. worn snugly and positioned properly. 3. Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is The pretensioners are triggered by the Occupant Restraint Controller (ORC).
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE until the driver’s or front passenger’s seat belt is buckled. NOTE: Chrysler Group LLC does not recommend deBeltAlert威 will be reactivated if the driver’s or passen- activating the BeltAlert威. ger’s seat belt is unbuckled for more than 10 seconds and 1. With all doors closed, and the ignition switch in any the vehicle speed is greater than 5 mph (8 km/h).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Watch for the Seat Belt Reminder Light to turn on while unbuckling the seat belt and turn off while re-buckling the seat belt. It may be necessary to retract the seat belt. 55 Pregnant women should wear the lap part of the belt across the thighs and as snug across the hips as possible. Keep the belt low so that it does not come across the abdomen. That way the strong bones of the hips will take the force if there is a collision. 4.
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Using a seat belt extender when not needed can increase the risk of injury in a collision. Only use when the seat belt is not long enough when it is worn low and snug and in the recommended seating positions. Remove and store the extender when not needed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 The Advanced Front Airbags have a multistage inflator NOTE: design. This allows the airbag to have different rates of • Airbag covers may not be obvious in the interior trim; but they will open during airbag deployment. inflation based on the severity and type of collision. This vehicle may be equipped with driver and/or front • After any collision, the vehicle should be taken to an authorized dealer immediately.
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Supplemental Side Airbag Inflatable Curtains (SABIC) • Front and Side Impact Sensors • Front Seat Belt Pretensioners, Seat Belt Buckle Switch, and Seat Track Position Sensors Advanced Front Airbag Features The Advanced Front Airbag system has multistage driver and front passenger airbags.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 WARNING! (Continued) • Do not mount any accessories to the knee bolster such as alarm lights, stereos, citizen band radios, etc. 2 Supplemental Side Airbag Inflatable Curtain (SABIC) — If Equipped SABIC airbags may offer side-impact and vehicle rollover protection to front and rear seat outboard occupants in addition to that provided by the body structure.
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The system includes side impact sensors adjacent to both front and rear seat occupants that are calibrated to deploy the SABIC airbags during impacts that require airbag occupant protection. WARNING! • If your vehicle is equipped with left and right Supplemental Side Airbag Inflatable Curtain (SABIC), do not stack luggage or other cargo up high enough to block the location of the SABIC.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Infants in rear-facing child restraints should NEVER ride in the front seat of a vehicle with a passenger Advanced Front Airbag. An airbag deployment can cause severe injury or death to infants in that position. Children that are not big enough to wear the vehicle seat belt properly (see Section on Child Restraints) should be secured in the rear seat in child restraints or beltpositioning booster seats.
62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If the airbag system in this vehicle needs to be modified to accommodate a disabled person, contact the Customer Center. Phone numbers are provided under ⬙If You Need Assistance⬙. WARNING! • Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly. In some collisions, the airbags won’t deploy at all. Always wear your seat belts even though you have airbags.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 ORC deploys the Advanced Front Airbags, SABIC air- The side airbags will not deploy in all side collisions. Side bags — if equipped, and front seat belt pretensioners — airbag deployment will depend on the severity and type if equipped, as required, depending on the severity and of collision. type of impact.
64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The ORC contains a backup power supply system that may deploy the airbags even if the battery loses power or it becomes disconnected prior to deployment. WARNING! Ignoring the Airbag Warning Light in your instrument panel could mean you won’t have the airbags to protect you in a collision. If the light does not come on, stays on after you start the vehicle, or if it comes on as you drive, have the airbag system checked right away by an authorized dealer.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 covers the window. The airbag inflates in about 30 ms (about one-quarter of the time that it takes to blink your eyes) with enough force to injure you if you are not belted and seated properly, or if items are positioned in the area where the side curtain airbag inflates. This especially applies to children. The side curtain airbag is only about The Advanced Front Airbag gas is vented through the 3-1/2 in (9 cm) thick when it is inflated.
66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Enhanced Accident Response System In the event of an impact causing airbag deployment, if the communication network remains intact, and the power remains intact, depending on the nature of the event the ORC will determine whether to have the Enhanced Accident Response System perform the following functions: If a Deployment Occurs The front airbags are designed to deflate immediately after deployment. • Cut off fuel to the engine.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • As the airbags deflate, you may see some smoke-like particles. The particles are a normal by-product of the process that generates the non-toxic gas used for airbag inflation. These airborne particles may irritate the skin, eyes, nose, or throat. If you have skin or eye irritation, rinse the area with cool water. For nose or throat irritation, move to fresh air. If the irritation continues, see your doctor.
68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Maintaining Your Airbag System WARNING! (Continued) WARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. You could be injured if the airbag system is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the steering wheel hub trim cover or the upper right side of the instrument panel.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 Airbag Warning Light You will want to have the airbags ready to inflate for your protection in a collision. While the airbag system is designed to be maintenance free, if any of the following occurs, have an authorized dealer service the system immediately. • The Airbag Warning Light does not come on for approximately six to eight seconds when the ignition switch is first placed into the RUN position.
70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Under certain circumstances, EDR data may not be accessing the electronic data stored, unless ordered to image the data by a court with legal jurisdiction (i.e., recorded (e.g., loss of battery power). pursuant to a warrant). A copy of the data will be In conjunction with other data gathered during a comprovided to the custodial entity upon request.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 United States and all Canadian provinces require that small children ride in proper restraint systems. This is the law, and you can be prosecuted for ignoring it. 3. Requested by police under a legal warrant. 4. Otherwise required by law. Data parameters that are recorded: Children 12 years and younger should ride properly • Diagnostic trouble code(s) and warning light status for buckled up in a rear seat, if available.
72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt. Always check the child seat Owner’s Manual to ensure you have the correct seat for your child. Use the restraint that is correct for your child. Infants and Child Restraints • Safety experts recommend that children ride rearward-facing in the vehicle until they are at least one year old and weigh at least 20 lbs (9 kg).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE seats used in the forward-facing direction are for children who weigh 20 to 40 lbs (9 to 18 kg) and who are older than one year. These child seats are also held in the vehicle by the lap/shoulder belt or the LATCH child restraint anchorage system. Refer to “LATCH — Child Seat Anchorage System (Lower Anchors and Tether for CHildren)”. 73 over the front of the seat when their back is against the seatback should use the lap/shoulder belt in a rear seat.
74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint. • A rearward-facing child restraint should only be used in a rear seat.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE system provides for the installation of the child restraint without using the vehicle’s seat belts, instead securing the child restraint using lower anchorages and upper tether straps from the child restraint to the vehicle structure. LATCH-compatible child restraint systems are now available.
76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Installing the LATCH-Compatible Child Restraint System We urge you to follow the manufacturer’s directions carefully when installing your child restraint. Not all child restraint systems will be installed as described here. Again, carefully follow the installation instructions that are provided with the child restraint system.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE child restraint rearward and downward into the seat, removing slack in the straps according to the child restraint manufacturer’s instructions. NOTE: • Ensure that the tether strap does not slip into the opening between the seatbacks as you remove slack in the strap. • When using the LATCH attaching system to install a child restraint, please ensure that all seat belts not being used for occupant restraints are stowed and out of reach of children.
78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE In the rear seat, you may have trouble tightening the lap/shoulder belt on the child restraint because the buckle or latch plate is too close to the belt path opening on the restraint. Disconnect the latch plate from the buckle and twist the short buckle end belt several times The seat belt must be in the Automatic Locking Mode in to shorten it. Insert the latch plate into the buckle with the order to enable a child restraint to be tightly installed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 79 3. Attach the tether strap hook (A) of the child restraint to the anchor (B) and remove slack in the tether strap according to the child restraint manufacturer’s instructions. NOTE: Ensure that the tether strap does not slip into the opening between the seatbacks as you remove slack in the strap. WARNING! Tether Strap Mounting 1 — Cover 3 — Attaching Strap A — Tether Strap Hook B — Tether Anchor 2.
80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant. Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur. For the recommended viscosity and quality grades refer to “Maintenance Procedures” in “Maintaining Your VePets should be restrained in the rear seat in pet harnesses hicle”.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE SAFETY TIPS 81 WARNING! (Continued) Transporting Passengers NEVER TRANSPORT PASSENGERS IN THE CARGO AREA. • Be sure everyone in your vehicle is in a seat and using a seat belt properly. Exhaust Gas WARNING! • Do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle.
82 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If it is necessary to sit in a parked vehicle with the engine running, adjust your heating or cooling controls to force outside air into the vehicle. Set the blower at high speed. If you are required to drive with the trunk/liftgate open, make sure that all windows are closed and the climate control BLOWER switch is set at high speed. DO NOT use the recirculation mode. inspect the exhaust system each time the vehicle is raised for lubrication or oil change.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE authorized dealer. If the light stays on, flickers, or comes on while driving, have the system checked by an authorized dealer. Defroster Check operation by selecting the defrost mode and place the blower control on high speed. You should be able to feel the air directed against the windshield. See your authorized dealer for service if your defroster is inoperable. Floor Mat Safety Information Always use floor mats designed to fit the foot well of your vehicle.
84 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • Always make sure that objects cannot fall into the driver foot well while the vehicle is moving. Objects can become trapped under the brake pedal and accelerator pedal causing a loss of vehicle control. • If required, mounting posts must be properly installed, if not equipped from the factory.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 䡵 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91 ▫ Tilt Mirrors In Reverse — If Equipped . . . . . . 94 ▫ Inside Day/Night Mirror . . . . . . . . . . . . . . . . 91 ▫ Power Mirrors . . . . . . . . . . . . . . . . . . . . . . . 94 ▫ Automatic Dimming Mirror — If Equipped . . . 92 ▫ Heated Mirrors — If Equipped . . . . . . . . . . . . 95 ▫ Outside Mirrors . . . . . . . . . . . . . . . . . . . . . .
86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Things You Should Know About Your Uconnect™ Phone . . . . . . . . . . . . . . . . . . . . 116 ▫ General Information . . . . . . . . . . . . . . . . . . 124 䡵 Voice Command — If Equipped . . . . . . . . . . . 124 ▫ Folding Rear Seat . . . . . . . . . . . . . . . . . . . . 136 䡵 Driver Memory Seat — If Equipped . . . . . . . . 138 ▫ Programming The Memory Feature . . . . . . . 139 ▫ Voice Command System Operation . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 ▫ Headlight Time Delay . . . . . . . . . . . . . . . . . 145 ▫ Intermittent Wiper System . . . . . . . . . . . . . . 151 ▫ Smartbeam™ — If Equipped . . . . . . . . . . . . 146 ▫ Mist Feature . . . . . . . . . . . . . . . . . . . . . . . . 152 ▫ Daytime Running Lights — If Equipped . . . . 147 ▫ Windshield Washers . . . . . . . . . . . . . . . . . . 152 ▫ Lights-On Reminder . . . . . . . . . . . . . . . . . .
88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ To Resume Speed . . . . . . . . . . . . . . . . . . . . 160 ▫ Setting The Following Distance In ACC . . . . 170 ▫ To Vary The Speed Setting . . . . . . . . . . . . . . 160 ▫ Adaptive Cruise Control (ACC) Menu . . . . . 172 ▫ To Accelerate For Passing . . . . . . . . . . . . . . 161 ▫ Display Warnings And Maintenance . . . . . . . 175 䡵 Adaptive Cruise Control (ACC) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 䡵 Garage Door Opener — If Equipped . . . . . . . . 190 ▫ Pinch Protect Override . . . . . . . . . . . . . . . . 198 ▫ Programming HomeLink威 . . . . . . . . . . . . . . 191 ▫ Venting Sunroof — Express . . . . . . . . . . . . . 198 ▫ Gate Operator/Canadian Programming . . . . 194 ▫ Sunshade Operation . . . . . . . . . . . . . . . . . . 198 ▫ Using HomeLink威 . . . . . . . . . . . . . . . . . . . 194 ▫ Wind Buffeting . . . . . . . . . . . . . . . . . . . .
90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Cargo Area . . . . . . . . . . . . . . . . . . . . . . . . 205 䡵 Rear Window Features . . . . . . . . . . . . . . . . . . 206 䡵 Cargo Area Features . . . . . . . . . . . . . . . . . . . 206 ▫ Rear Window Defroster . . . . . . . . . . . . . . . . 206 ▫ Trunk Mat — If Equipped . . . . . . . . . . . . . . 206 䡵 Load Leveling System — If Equipped . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91 MIRRORS Inside Day/Night Mirror A two-point pivot system allows for horizontal and vertical mirror adjustment. Adjust the mirror to center on the view through the rear window. The mirror should be adjusted while set in the day position (toward the windshield). 3 Headlight glare can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle).
92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Dimming Mirror — If Equipped This mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light next to the button will illuminate to indicate when the dimming feature is activated. CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Vehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they really are. Relying too much on your passenger side convex mirror could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in the passenger side convex mirror. 93 turned on or off by pressing the button at the base of the inside mirror.
94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE the Remote Keyless Entry (RKE) transmitter or open any vehicle is shifted out of the REVERSE position. Each door. This LED shines outward to illuminate the front stored memory setting will have an associated Tilt Mirand rear door handles. It also shines downward to rors in Reverse position. illuminate the area in front of the doors.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 NOTE: For vehicles equipped with Driver Memory Seat, you can use your Remote Keyless Entry (RKE) transmitter or the memory switch on the driver’s door trim panel to return the power mirrors to preprogrammed positions. Refer to “Driver Memory Seat” in “Understanding the Features of Your Vehicle” for further information. Power Mirror Control After selecting a mirror, move the knob in the same direction you want the mirror to move.
96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Illuminated Vanity Mirrors — If Equipped An illuminated vanity mirror is located on the sun visor. To use the mirror, rotate the sun visor downward and swing the mirror cover upward. The light turns on automatically. Closing the mirror cover turns off the light. Uconnect™ Phone — IF EQUIPPED Uconnect™ Phone is a voice-activated, hands-free, invehicle communications system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • www.jeep.com/uconnect • or call 1–877–855–8400 Uconnect™ Phone allows you to transfer calls between the system and your cellular phone as you enter or exit your vehicle and enables you to mute the system’s microphone for private conversation. 97 system. Only one linked (or paired) cellular phone can be used with the system at a time. The system is available in English, Spanish, or French languages.
98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The radio display will be used for visual prompts from Voice Command Button Actual button location may vary with the ra- the Uconnect™ Phone such as ⬙CELL⬙ or caller ID on dio. The individual buttons are described in the certain radios. “Operation” section.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • For each feature explanation in this section, only the combined form of the voice command is given. You can also break the commands into parts and say each part of the command when you are asked for it. For example, you can use the combined form voice command ⬙Phonebook New Entry,⬙ or you can break the combined form command into two voice commands: ⬙Phonebook⬙ and ⬙New Entry.
100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The following are general phone to Uconnect™ Phone • You will then be asked to give your cellular phone a pairing instructions: priority level between one and seven, with one being the highest priority. You can pair up to seven cellular • Press the button to begin. phones to your Uconnect™ Phone. However, at any given time, only one cellular phone can be in use, • After the ⬙Ready⬙ prompt and the following beep, say connected to your Uconnect™ Phone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The system will prompt you to say the number you want to call. • For example, you can say ⬙234-567-8901⬙. • The Uconnect™ Phone will confirm the phone number and then dial. The number will appear in the display of certain radios. Call by Saying a Name • Press the button to begin. 101 or downloaded phonebook. To learn how to store a name in the phonebook, refer to ⬙Add Names to Your Uconnect™ Phonebook,⬙ in the phonebook.
102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • When prompted, enter the number designation (e.g., ⬙Home,⬙ ⬙Work,⬙ ⬙Mobile,⬙ or ⬙Pager⬙). This will allow you to store multiple numbers for each phonebook entry, if desired.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 • Depending on the maximum number of entries downloaded, there may be a short delay before the latest downloaded names can be used. Until then, if available, the previous downloaded phonebook is available for use. Phonebook Download — Single Entry If equipped and supported by your phone, Uconnect™ Phone allows the user to download entries from their phone via Bluetooth威. To use this feature, press the button and say “Phonebook Download.
104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE first disconnect or drop the Bluetooth威 connection to • You will then be asked for the name of the phonebook the Uconnect™ Phone, and then send the address entry that you wish to edit. book entry via Bluetooth威. Please see your phone • Next, choose the number designation (home, work, Owner’s Manual for specific instructions on how to cellular, or pager) that you wish to edit. drop the Bluetooth威 connection.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 • After you enter the name, the Uconnect™ Phone will ask you which designation you wish to delete: home, NOTE: Editing phonebook entries is recommended work, cellular, pager, or all. Say the designation you when the vehicle is not in motion. wish to delete. • Press the button to begin. • Note that only the phonebook entry in the current language is deleted. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Phonebook Delete.
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Note that only the phonebook in the current language • The Uconnect™ Phone will then prompt you as to the is deleted. number designation you wish to call. • Automatic downloaded phonebook entries cannot be • The selected number will be dialed. deleted or edited. Phone Call Features List All Names in the Uconnect™ Phonebook The following features can be accessed through the Uconnect™ Phone if the feature(s) are available on your button to begin.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 call, press and hold the button until you hear a by the phone number or phonebook entry you wish to single beep, indicating that the incoming call was call. The first call will be on hold while the second call is in progress. To go back to the first call, refer to ⬙Toggling rejected. Between Calls⬙ in this section. To combine two calls, refer Answer or Reject an Incoming Call - Call to ⬙Conference Call⬙ in this section.
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Conference Call When two calls are in progress (one active and one on button until you hear a hold), press and hold the double beep indicating that the two calls have been joined into one conference call. on hold may not become active automatically. This is cell phone-dependent. To bring the call back from hold, press and hold the button until you hear a single beep. Redial • Press the button to begin.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 • After the ignition key is switched to OFF, a call can • After the ⬙Ready⬙ prompt and the following beep, say continue on the Uconnect™ Phone either until the call the name of the language you wish to switch to ends, or until the vehicle battery condition dictates English, Espanol, or Francais. cessation of the call on the Uconnect™ Phone and • Continue to follow the system prompts to complete transfer of the call to the cellular phone.
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If the phone is not reachable and the Uconnect™ Phone is • If supported, this number may be programmable on button and operational, you may reach the emergency number as some systems. To do this, press the follows: say ‘Setup’, followed by ‘Emergency’. • Press the • The Uconnect™ Phone does slightly lower your chances of successfully making a phone call as to that • After the ⬙Ready⬙ prompt and the following beep, say for the cellular phone directly.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 • After the ⬙Ready⬙ prompt and the following beep, say certain companies, which time out a little too soon to work properly with the Uconnect™ Phone. ⬙Towing Assistance.⬙ NOTE: • The towing assistance number dialed is based on the country where the vehicle is purchased (1-800-5282069 for the U.S., 1-877-213-4525 for Canada, 55-143454 for Mexico City and 1-800-712-3040 for outside Mexico City in Mexico).
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE on your cellular phone keypad, you can press the button and say the sequence you wish to enter, followed by the word ⬙Send.⬙ For example, if required to enter your PIN followed with a pound, (3 7 4 6 #), you can button and say, ⬙3 7 4 6 # Send.⬙ Saying press the a number, or sequence of numbers, followed by ⬙Send,⬙ is also to be used for navigating through an automated customer service center menu structure, and to leave a number on a pager.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Press the 113 dialing a number with your paired Bluetooth威 cellular phone, the audio will be played through your vehicle’s • After the ⬙Ready⬙ prompt and the following beep, say audio system. The Uconnect™ Phone will work the same ⬙Setup Confirmations.⬙ The Uconnect™ Phone will as if you dial the number using Voice Command.
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Following the beep, say ⬙Mute.⬙ In order to un-mute the Uconnect™ Phone: • Press the button. • Following the beep, say ⬙Mute off.⬙ Connect or Disconnect Link Between the Uconnect™ Phone and Cellular Phone Your cellular phone can be paired with many different electronic devices, but can only be actively ⬙connected⬙ with one electronic device at a time.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 • The Uconnect™ Phone will play the phone names of • The selected phone will be used for the next phone all paired cellular phones in order from the highest to call. If the selected phone is not available, the the lowest priority. To “select” or “delete” a paired Uconnect™ Phone will return to using the highest button and phone being announced, press the priority phone present in or near (approximately within 30 ft (9 m)) the vehicle. say “Select” or “Delete.
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Things You Should Know About Your Uconnect™ Phone Uconnect™ Phone Tutorial To hear a brief tutorial of the system features, press the button and say “Uconnect™ Tutorial.” Voice Training For users experiencing difficulty with the system recognizing their voice commands or numbers, the Uconnect™ Phone Voice Training feature may be used.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 • Speak normally, without pausing, just as you would • When navigating through an automated system such speak to a person sitting a few feet/meters away from as voice mail, or when sending a page, at the end of you. speaking the digit string, make sure to say ⬙Send.⬙ • Make sure that no one other than you is speaking • Storing names in the phonebook when the vehicle is during a Voice Command period. not in motion is recommended.
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • In a convertible vehicle, system performance may be • Echo at the phone far end can sometimes be reduced compromised with the convertible top down. by lowering the in-vehicle audio volume. Phone Far End Audio Performance • Audio quality is maximized under: • low-to-medium blower setting, • low-to-medium vehicle speed, • low road noise, • smooth road surface, • fully closed windows, • dry weather conditions, and • operation from the driver’s seat.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 3
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 3
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Primary zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location all Voice Commands Alternate(s) Voice Commands Alternate(s) Primary call cancel confirmation prompts continue delete dial download edit emergency English erase all Espanol Francais help home
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Primary language list names list phones mobile mute mute off new entry no pager pair a phone phone pairing phonebook previous record again redial Voice Commands Alternate(s) pairing phone book 123 Voice Commands Primary Alternate(s) return to main menu return or main menu select phone select send set up phone settings or phone set up towing assistance transfer call Uconnect™ Tutorial try again voice training work yes 3
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE General Information This device complies with Part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 NOTE: If you do not say a command within a few For example, if you are in the disc menu and you are seconds, the system will present you with a list of listening to FM radio, you can speak commands from the disc menu or from the FM radio menu. options. If you ever wish to interrupt the system while it lists When using this system, you should speak clearly and at button, listen a normal speaking volume.
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE In this mode, you can say the following commands: Commands The Voice Command system understands two types of • “Radio” (to switch to the radio mode) commands. Universal commands are available at all times. Local commands are available if the supported • “Disc” (to switch to the disc mode) radio mode is active. • “Memo” (to switch to the memo recorder) Changing the Volume • “System Setup” (to switch to system setup) 1.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Radio FM To switch to the FM band, say “FM” or “Radio FM”.
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Memo To switch to the voice recorder mode, say “Memo”. In this mode, you may say the following commands: − “Previous” (to play the previous memo) − “Delete” (to delete a memo) • “Delete All” (to delete all memos) • “New Memo” (to record a new memo) — During the System Setup recording, you may press the Voice Command button to stop recording. You proceed by saying one of To switch to system setup, say “Setup”.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 NOTE: Keep in mind that you have to press the Voice SEATS button first and wait for the beep Seats are a primary part of the Occupant Restraint System Command of the vehicle. They need to be used properly for safe before speaking the “Barge In” commands. operation of the vehicle.
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Seats The power seat switch is located on the outboard side of the seat near the floor. Use this switch to move the driver’s seat up or down, forward or rearward or to recline the seat. The passenger’s seat will move up or down, forward or rearward. WARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Reclining Seats The recline control is used to adjust the position of the seatback. To adjust the seatback forward, move the control toward the front of the vehicle. To move the seatback rearward, move the control toward the rear of the vehicle. 131 3 The recliner control is located on the outboard side of the seat.
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or even fatally injured. Use the recliner only when the vehicle is parked. Lumbar Support This feature allows you to increase or decrease the amount of lumbar support. Turn the control lever forward to increase and rearward to decrease the desired amount of lumbar support.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To raise the head restraint, pull upward on the head restraint. To lower the head restraint, press the large button, located on the base of the head restraint, and push downward on the head restraint. 133 To remove the head restraint, pull upward on the head restraint to it’s highest position, push in both buttons at the base of each head restraint rod, and simultaneously pull up on the head restraint.
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To install the head restraint, insert the head restraint rods into each guide, apply pressure down on the headrest until the head restraint reaches the first lock position, push the large button in and push down and adjust head restraint to desired position. Heated Seats — If Equipped This feature heats the front driver and passenger seats. The controls for each front seat are located near the bottom center of the instrument panel.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 On vehicles equipped with rear heated seats, the seats each switch indicate the level of heat in use. Two indicaclosest to the doors are heated. The controls for these tors will illuminate for High, one for Low and none for Off. seats are located on the rear of the center console. Press the switch once to select High-level heating. Press the switch a second time to select Low-level heating. Press the switch a third time to shut the heating elements Off.
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! CAUTION! • Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion or other physical condition must exercise care when using the seat heater. It may cause burns even at low temperatures, especially if used for long periods of time. • Do not place anything on the seat that insulates against heat, such as a blanket or cushion.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 WARNING! Folding Rear Seats When the seatback is folded to the upright position, make sure it is latched by strongly pulling on the top of the seatback above the seat strap. • Be certain that the seatback is securely locked into position. If the seatback is not securely locked into position, the seat will not provide the proper stability for child seats and/or passengers. An improperly latched seat could cause serious injury.
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE DRIVER MEMORY SEAT — IF EQUIPPED This feature allows the driver to store up to two different memory profiles for easy recall through a memory switch. Each memory profile contains desired position settings for the driver seat, side mirrors, adjustable pedals (if equipped), and power tilt and telescopic steering column (if equipped) and a set of desired radio station presets.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 NOTE: • Memory profiles can be set without the vehicle in NOTE: Saving a new memory profile will erase an PARK, but the vehicle must be in PARK to recall a existing profile from memory. memory profile. To create a new memory profile, perform the following: • The Recall Memory with Remote Key Unlock feature can be enabled through the EVIC (if equipped). Refer 1. Place the ignition into the RUN position. to “Electronic Vehicle Information Center (EVIC)/ 2.
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To program your RKE transmitters, perform the follow- NOTE: Your RKE transmitters can be unlinked to your ing: memory settings by pressing the SET (S) button followed by the UNLOCK button on the RKE transmitter in Step 4 1. Remove the Key Fob from the ignition (or change the above. ignition to OFF, for vehicles equipped with Keyless Memory Position Recall Go™). 2. Select desired memory profile 1 or 2.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 To recall the memory setting for driver two, press Key Fob from the ignition (or change the ignition to OFF, MEMORY button number 2 on the driver’s door or the for vehicles equipped with Keyless Go™). UNLOCK button on the RKE transmitter linked to • When you remove the Key Fob from the ignition (or memory position 2. change the ignition to OFF, for vehicles equipped with Keyless Go™), the driver seat will move about 2.
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The Easy Entry/Easy Exit feature is disabled when the driver seat position is less than 0.9 in (22.7 mm) forward of the rear stop. At this position, there is no benefit to the driver by moving the seat for Easy Exit or Easy Entry. Each stored memory setting will have an associated Easy Entry and Easy Exit position. NOTE: The Easy Entry/Easy Exit feature can be enabled or disabled through the programmable features in the EVIC.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 CAUTION! To prevent possible damage, do not slam the hood to close it. Lower the hood, until it is open approximately 6 in (15 cm), and then drop it. This should secure both latches. Never drive your vehicle unless the hood is fully closed, with both latches engaged. WARNING! Hood Safety Catch Use the hood prop rod (if equipped) to secure the hood in the open position. Be sure the hood is fully latched before driving your vehicle.
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE LIGHTS Headlight Switch The headlight switch is located on the left side of the instrument panel. This switch controls the operation of the headlights, parking lights, instrument panel lights, instrument panel light dimming, interior lights and fog lights. Headlight Switch Rotate the headlight switch clockwise to the first detent for parking light and instrument panel light operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Headlights — If Equipped This system automatically turns the headlights on or off according to ambient light levels. To turn the system on, rotate the headlight switch counterclockwise to the A (AUTO) position. When the system is on, the headlight time delay feature is also on. This means the headlights will stay on for up to 90 seconds after you place the ignition into the OFF position.
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If you turn the headlights off before the ignition, they will To Activate turn off in the normal manner. 1. Select “Automatic High Beams — ON” through the NOTE: The lights must be turned off within 45 seconds EVIC. Refer to “Electronic Vehicle Information Center of placing the ignition in the OFF position to activate this (EVIC)/Customer-Programmable Features” in “Understanding Your Instrument Panel” for further information. feature.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 1. Pull the multifunction lever toward you to switch the Lights-On Reminder headlights from the high beam to the low beam position. If the headlights or parking lights are on after the ignition is placed in the OFF position, a chime will sound to alert 2. Rotate the headlight switch clockwise from the AUTO the driver when the driver’s door is opened. to the on position.
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Multifunction Lever The multifunction lever controls the operation of the turn signals, headlight beam selection and passing lights. The multifunction lever is located on the left side of the steering column. Turn Signals Move the multifunction lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 High/Low Beam Switch Push the multifunction lever away from you to switch the headlights to high beam. Pull the multifunction lever toward you to switch the headlights back to low beam. Flash-to-Pass You can signal another vehicle with your headlights by lightly pulling the multifunction lever toward you. This will turn on the high beams headlights until the lever is released.
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE open. This includes the glove box light, but not the trunk Interior Light Defeat (OFF) light. To restore interior light operation, either place the Rotate the dimmer control to the extreme bottom off position. The interior lights will remain off when the ignition in the RUN position or cycle the light switch. doors are open.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 CAUTION! Turn the windshield wipers off when driving through an automatic car wash. Damage to the windshield wipers may result if the wiper switch is left in any position other than off. Intermittent Wiper System Use the intermittent wiper when weather conditions make a single wiping cycle with a variable pause between cycles desirable. Rotate the end of the multifunction lever to select the desired delay interval.
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Mist Feature Lightly push the multifunction lever inward (toward the steering column) to activate a single wipe cycle to clear off road mist or spray from a passing vehicle. The wipers will continue to operate until you release the multifunction lever. WARNING! Sudden loss of visibility through the windshield could lead to an accident. You might not see other vehicles or other obstacles.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE The Headlights On with Wipers feature can be turned on or off through the Electronic Vehicle Information Center (EVIC) (if equipped). Refer to “Electronic Vehicle Information Center (EVIC)/Personal Settings (CustomerProgrammable Features)” in “Understanding Your Instrument Panel” for further information. Rain Sensing Wipers — If Equipped This feature senses moisture on the windshield and automatically activates the wipers for the driver.
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The Rain Sensing system has protective features for the TILT/TELESCOPING STEERING COLUMN wiper blades and arms. It will not operate under the This feature allows you to tilt the steering column upward or downward. It also allows you to lengthen or following conditions: shorten the steering column.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To unlock the steering column, pull the control handle outward. To tilt the steering column, move the steering wheel upward or downward as desired. To lengthen or shorten the steering column, pull the steering wheel outward or push it inward as desired. To lock the steering column in position, push the control handle inward until fully engaged.
156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To tilt the steering column, move the lever up or down as desired. To lengthen or shorten the steering column, pull the lever toward you or push the lever away from you as desired. NOTE: For vehicles equipped with Driver Memory Seat, you can use your Remote Keyless Entry (RKE) transmitter or the memory switch on the driver’s door trim panel to return the tilt/telescopic steering column to pre-programmed positions.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 • The pedals can be adjusted while driving. • The pedals cannot be adjusted when the vehicle is in REVERSE or when the Electronic Speed Control is on. One of the following messages will display in the Electronic Vehicle Information Center (EVIC) (if equipped) if a pedal adjustment is attempted when the system is locked out: “Adjustable Pedal Disabled — Cruise Control Engaged” or “Adjustable Pedal Disabled — Vehicle In Reverse.
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! The Electronic Speed Control lever, located on the rightside of the steering wheel, operates the system. Do not place any article under the adjustable pedals or impede its ability to move as it may cause damage to the pedal controls. Pedal travel may become limited if movement is stopped by an obstruction in the adjustable pedal’s path. WARNING! Do not adjust the pedals while the vehicle is moving. You could lose control and have an accident.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: In order to ensure proper operation, the Electronic Speed Control System has been designed to shut down if multiple Speed Control functions are operated simultaneously. If this occurs, the Electronic Speed Control System can be reactivated by pushing the Electronic Speed Control ON/OFF button and resetting the desired vehicle set speed. To Activate Push and release the ON/OFF button, located on the end of the Electronic Speed Control lever.
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: • Electronic Speed Control will only function in 3rd, 4th, or 5th gear when in the Autostick威 mode (if equipped). To Resume Speed If you deactivated the Electronic Speed Control without erasing the set speed from memory and your vehicle speed is above 20 mph (32 km/h) you can resume the previous set speed. To do so, push the lever upward to • The Electronic Speed Control may not engage if a RESUME ACCEL and release.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To decrease speed while Electronic Speed Control is set, push down and hold the lever in SET DECEL. If the lever is continually held in the SET DECEL position, the set speed will continue to until the lever is released. Release the lever when the desired speed is reached, and a new set speed will be established. Tapping the Electronic Speed Control lever to SET DECEL once will result in a 1 mph (1.6 km/h) speed decrease.
162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ADAPTIVE CRUISE CONTROL (ACC) — IF EQUIPPED Adaptive Cruise Control (ACC) increases the driving convenience provided by cruise control while traveling on highways and major roadways. However, it is not a safety system and not designed to prevent collisions. ACC will allow you to keep cruise control engaged in light to moderate traffic conditions without the constant need to reset your cruise control.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! (Continued) • Cannot take street, traffic, and weather conditions into account, and may be limited upon adverse sight distance conditions. • Does not predict the lane curvature or the movement of preceding vehicles and will not compensate for such changes. • Does not always fully recognize complex driving conditions, which can result in wrong or missing distance warnings.
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The Cruise Control system has two control modes: • Adaptive Cruise Control mode for maintaining an appropriate distance between vehicles. • Normal (fixed speed) cruise control mode for cruising at a constant preset speed. For additional information, refer to “Normal (Fixed Speed) Cruise Control Mode” in this section. Note: The system will not react to preceding vehicles. Always be aware of the mode selected. You can change the mode by using the control lever.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 When the system is turned on and in the READY state, To Activate the Electronic Vehicle Information Center (EVIC) dis- Push and release the ON/OFF/MODE button located on the end of the speed control lever. The ACC menu in the plays “ACC READY.” EVIC displays “ACC READY.” When the system is OFF, the EVIC displays “CRUISE OFF.” NOTE: You cannot enable ACC under the following conditions: • When you apply the brakes. • When the parking brake is set.
166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Leaving the Adaptive Cruise Control (ACC) system on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the system off when you are not using it. To Set a Desired ACC Speed When the vehicle reaches the speed desired, push the lever downward (SET/DECEL) and release. The EVIC Remove your foot from the accelerator pedal.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 • The system will not be controlling the distance be- • You softly tap the brake pedal. tween your vehicle and the vehicle ahead. The vehicle • You depress the brake pedal. speed will only be determined by the position of the • You pull the speed control lever toward you to CANaccelerator pedal. CEL. • The Electronic Stability Program/Traction Control System (ESP/TCS) activates.
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Turn Off The system will turn off and erase the set speed in memory if: • You push and release the ON/OFF/MODE button. • You turn OFF the ignition. • You switch off ESP. WARNING! The Resume function should only be used if traffic and road conditions permit. Resuming a set speed that is too high or too low for prevailing traffic and road conditions could cause the vehicle to accelerate or decelerate too sharply for safe operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 While ACC is set, the set speed can be decreased by • The ACC system can only apply a maximum of 25% of pushing and holding the lever down (SET/DECEL). If the vehicle’s braking capability and will not bring the the lever is continually held, the set speed will continue vehicle to a complete stop. to decrease in 5 mph (10 km/h) increments until the lever • The ACC system maintains set speed when driving up is released.
170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Setting the Following Distance in ACC The specified following distance for ACC can be set by varying the distance setting between long, medium, and short. Using this distance setting and the vehicle speed, ACC calculates and sets the distance to the vehicle ahead. This distance setting displays in the EVIC. To change the distance setting, push the lever away from you (DISTANCE) and release.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 • The vehicle ahead slows to a speed below 15 mph braking capacity. When this occurs, you should immedi(24 km/h) and the system automatically disengages ately apply the brakes as needed to maintain a safe distance from the vehicle ahead. itself. • The distance setting is changed. • The system disengages. (Refer to the information on ACC Activation).
172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Adaptive Cruise Control (ACC) Menu The EVIC displays the current ACC system settings. The EVIC is located in the upper part of the instrument cluster between the speedometer and the tachometer. The information it displays depends on ACC system status.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173 3 ACC SET − When ACC is set, the set speed will display. 1 — Sensed Vehicle Indicator 2 — Set Speed 3 — Your Vehicle 4 — Following Distance Setting: Three Bars = Long; Two Bars = Medium; One Bar = Short.
174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The set speed will continue to display in place of the The ACC SET screen will display once again if any ACC odometer reading when changing the EVIC display activity occurs, which may include any of the following: while ACC is set.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175 Display Warnings and Maintenance ACC Blinded Warning The ACC Blinded Warning will display when conditions temporarily limit system performance. This most often occurs at times of poor visibility, such as in snow, fog, heavy rain, or when driving into direct sunlight (sunrise or sunset). The ACC system may also become temporarily blinded due to obstructions, such as dirt or ice.
176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If weather conditions are not a factor, the driver should • Always keep the sensor clean. Carefully wipe the examine the sensor. It may require cleaning or removal of sensor lens with a soft cloth. Be cautious not to an obstruction. The sensor is located behind the grille, damage the sensor lens. slightly offset from the center of the grille. • Do not remove any screws from the sensor or the sensor mount.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177 NOTE: Installing a vehicle front-end protector or an aftermarket grille or modifying the grille is not recommended. Doing so may block the sensor and inhibit ACC operation. ACC Unavailable Warning If the system turns off, and the EVIC displays ⬙ACC UNAVAILABLE,⬙ there may be a temporary malfunction that limits ACC functionality. Although the vehicle is still drivable under normal conditions, ACC will be temporarily unavailable.
178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Precautions While Driving with ACC In certain driving situations, ACC may have detection issues. In these cases, ACC may brake late or unexpectedly. The driver needs to stay alert and may need to intervene. Adding a Trailer Hitch The weight of a trailer hitch may affect the performance of ACC. If there is a noticeable change in performance following the installation of a hitch, such as reduced detection range, please see your authorized dealer for service.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179 Using ACC on Hills When driving on hills, ACC may not detect a vehicle in your lane. Depending on the speed, vehicle load, traffic conditions, and the steepness of the hills, ACC performance may be limited. 3 ACC may occasionally provide braking and/or a driver alert that you consider unnecessary. This may be the system’s response to signs, guardrails, and other stationary objects in a curve. This may also occur at the base of steep hills.
180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Lane Changing ACC will not detect a vehicle until it is completely in the lane in which you are traveling. In the illustration shown, ACC has not yet detected the vehicle changing lanes and it may detect the vehicle until it’s too late for the ACC system to take action. ACC will not detect a vehicle until it is completely in the lane. There will not be sufficient distance to the lane-changing vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181 3 Stationary Objects and Vehicles General Information ACC does not react to stationary objects and stationary CLASS 1 LASER PRODUCT vehicles. For example, ACC will not react in situations Classification Specifications: where the vehicle you are following exits your lane and 21 C.F.R part 1040.10 & 1040.11 the vehicle ahead is stopped in your lane. Always be DIN EN 60825-1:2003 attentive and ready to apply the brakes if necessary.
182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Normal (Fixed Speed) Cruise Control Mode In addition to adaptive cruise control mode, a normal (fixed speed) cruise control mode is available for cruising at fixed speeds. The Normal cruise control mode is designed to maintain a set cruising speed without requiring the driver to operate the accelerator. Cruise control can only be operated if the vehicle speed is above 25 mph (40 km/h).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 183 To Vary the Speed Setting There are two ways to change the set speed: To Resume Push the lever up and release (RESUME/ACCEL) and then remove your foot from the accelerator pedal. The • Use the accelerator pedal to adjust the vehicle to the EVIC will display the last set speed. desired speed and push the lever down (SET/DECEL).
184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE PARKSENSE姞 REAR PARK ASSIST The ParkSense威 Rear Park Assist system is a driver aid that senses for obstacles behind the vehicle. Refer to ParkSense威 System Usage Precautions for limitations of this system and recommendations. ParkSense威 uses four sensors located in the rear bumper to scan for obstacles up to 79 in (200 cm) away from the rear bumper fascia.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE The Warning Display contains two sets of yellow and red indicators, one set to warn of obstacles behind the left rear of the vehicle and the other set to warn of obstacles behind the right rear of the vehicle. The driver can view the indicators either through the rearview mirror or by looking at the display above the rear window.
186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ParkSense姞 System Usage Precautions • ParkSense威, when on, will MUTE the radio when it is sounding a tone. NOTE: • Ensure that the rear bumper is free of snow, ice, mud, • If a ParkSense威 system malfunction occurs, a single dirt and debris to keep the ParkSense威 Rear Park chime will sound once per ignition cycle. In addition, Assist system operating properly.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Objects must not be within 12 in (30 cm) from the rear fascia/bumper while driving the vehicle. Failure to do so can result in the system misinterpreting a close object as a sensor problem, causing the “SERVICE PARK ASSIST SYSTEM” message to be displayed in the instrument cluster. CAUTION! • The ParkSense威 Rear Park Assist system is only a parking aid and it is unable to recognize every obstacle, including small obstacles.
188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! WARNING! (Continued) • Drivers must be careful when backing up even when using the ParkSense威 Rear Park Assist system. Always check carefully behind your vehicle, look behind you, and be sure to check for pedestrians, animals, other vehicles, obstructions, and blind spots before backing up. You are responsible for safety and must continue to pay attention to your surroundings. Failure to do so can result in serious injury or death.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE OVERHEAD CONSOLE The overhead console contains courtesy/reading lights and storage for sunglasses. Universal Garage Door Opener (HomeLink威) buttons and power sunroof switch may also be included, if equipped. 189 Courtesy/Reading Lights At the forward end of the console are two courtesy/ reading lights. Press the lens to turn on the light. Press it a second time to turn off the light.
190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The storage compartment access is a ⬙push/push⬙ design. Push on the raised bar on the compartment door to open. Push on the raised bar to close. GARAGE DOOR OPENER — IF EQUIPPED HomeLink威 replaces up to three remote controls (handheld transmitters) that operate devices such as garage door openers, motorized gates, lighting or home security systems. The HomeLink威 unit operates off your vehicle’s battery.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Your motorized door or gate will open and close while you are training the Universal Transceiver. Do not train the transceiver if people, pets, or other objects are in the path of the door or gate. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by federal safety standards. This includes most garage door opener models manufactured after 1982.
192 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Place the handheld transmitter 1 to 3 in (3 to 8 cm) NOTE: Some gate operators and garage door openers from the HomeLink威 buttons while keeping the EVIC may require you to replace Step 3 with procedures noted display in view. in the “Gate Operator/Canadian Programming” section. For optimal training, point the battery end of the hand- 4. Press and hold the just-trained HomeLink威 button. If held transmitter away from the HomeLink威.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 193 This can usually be found where the hanging antenna 6. Firmly press and release the LEARN or TRAINING wire is attached to the garage door opener motor (it is button. The name and color of the button may vary by NOT the button normally used to open and close the manufacturer. door). NOTE: You have 30 seconds in which to initiate the next step after the LEARN button has been pressed. 7.
194 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Gate Operator/Canadian Programming Canadian radio-frequency laws require transmitter signals to “time-out” (or quit) after several seconds of transmission – which may not be long enough for HomeLink威 to pick up the signal during programming. Similar to this Canadian law, some U.S. gate operators are designed to “time-out” in the same manner. successfully accepted the frequency signal.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 195 The HomeLink威 Universal Transceiver is disabled when Reprogramming A Single HomeLink姞 Button To reprogram a channel that has been previously trained, the Vehicle Security Alarm is active. follow these steps: Troubleshooting Tips If you are having trouble programming HomeLink威, here 1. Place the ignition in the RUN position. are some of the most common solutions: 2.
196 UNDERSTANDING THE FEATURES OF YOUR VEHICLE General Information POWER SUNROOF — IF EQUIPPED This device complies with FCC rules Part 15 and Industry The power sunroof switch is located between the sun Canada RSS-210. Operation is subject to the following visors on the overhead console. two conditions: 1. This device may not cause harmful interference 2.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 197 WARNING! WARNING! (Continued) • Never leave children in a vehicle with the key in the ignition switch (or with the ignition in the Accessory or Run position, for vehicles equipped with Keyless Go™). Occupants, particularly unattended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death.
198 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Pinch Protect Feature This feature will detect an obstruction in the opening of the sunroof during Express Close operation. If an obstruction in the path of the sunroof is detected, the sunroof will automatically retract. If this occurs remove the obstruction and press the switch forward and release to Express Close. Pinch Protect Override If a known obstruction (ice, debris, etc.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occurrence and can be minimized. If the buffeting occurs with the rear windows open, then open the front and rear windows together to minimize the buffeting.
200 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ELECTRICAL POWER OUTLETS There are two 12 Volt (13 Amp) electrical power outlets on this vehicle. Both of the power outlets are protected by a fuse. Insert cigar lighter or accessory plug into the power outlets for use to ensure proper operation. NOTE: • To ensure proper operation a MOPAR威 knob and element must be used. • Do not exceed the maximum power of 160 Watts (13 Amps) at 12 Volts.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE The center console outlet is powered directly from the battery (power available at all times). Items plugged into this outlet may discharge the battery and/or prevent the engine from starting. Center Console Power Outlet 201 WARNING! To avoid serious injury or death: • Only devices designed for use in this type of outlet should be inserted into any 12 Volt outlet. • Do not touch with wet hands. • Close the lid when not in use and while driving the vehicle.
202 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! CAUTION! (Continued) • Many accessories that can be plugged in draw power from the vehicle’s battery even when not in use (i.e., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting. • Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.) will degrade the battery even more quickly.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 203 CUPHOLDERS Rear Seat Cupholders The rear seat cupholders are located in the center armrest Front Seat Cupholders between the rear seats. The cupholders are positioned The cupholders are located in the forward edge of the forward in the armrest and side-by-side to provide center console. convenient access to beverage cans or bottles while maintaining a resting place for the rear occupants elbows.
204 UNDERSTANDING THE FEATURES OF YOUR VEHICLE STORAGE Console Features The center console contains two shift bezel cubby bins with rubber mats for holding small items. For vehicles not equipped with navigation radio, the console also contains an extra storage bin located below the climate control, which holds up to four CD jewel cases. Two separate storage compartments are also located underneath the armrest.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE The top compartment holds small items, such as a pen and note pad, while the larger bottom compartment will hold CDs and alike. The bottom compartment also contains a 12 Volt power outlet and a molded-in coin holder (designed to hold various size coins). A slot in the left and right side of the top compartment provides clearance for power cords to pass conveniently out of the bin with the lid closed.
206 UNDERSTANDING THE FEATURES OF YOUR VEHICLE When the seatback is folded to the upright position, make sure it is latched by strongly pulling on the top of the seatback above the seat strap. WARNING! • Be certain that the seatback is securely locked into position. If the seatback in not securely locked into position, the seat will not provide the proper stability for child seats and/or passengers. An improperly latched seat could cause serious injury.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE rear window defroster and the heated outside mirrors (if equipped). An indicator in the button will illuminate when the rear window defroster is on. The rear window defroster automatically turns off after approximately 10 minutes. For an additional five minutes of operation, press the button a second time. CAUTION! Failure to follow these cautions can cause damage to the heating elements: • Use care when washing the inside of the rear window.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 Instrument Panel Features . . . . . . . . . . . . . . . 213 ▫ Keyless Go Display — If Equipped . . . . . . . . 240 䡵 Instrument Cluster — Base . . . . . . . . . . . . . . . 214 ▫ Automatic All Wheel Drive (AWD) Displays — If Equipped . . . . . . . . . . . . . . . . . . . . . . 241 䡵 Instrument Cluster — Premium . . . . . . . . . . . 215 䡵 Instrument Cluster Descriptions . . . . . . . . . . . 216 䡵 Electronic Vehicle Information Center (EVIC) — If Equipped .
210 UNDERSTANDING YOUR INSTRUMENT PANEL 䡵 Media Center 730N/430 (RER/REN/RBZ) — AM/FM Stereo Radio And CD/DVD/HDD/ NAV — If Equipped . . . . . . . . . . . . . . . . . . . . 252 ▫ Operating Instructions — Voice Command System — If Equipped . . . . . . . . . . . . . . . . . 252 ▫ Operating Instructions — Uconnect™ phone — If Equipped . . . . . . . . 252 ▫ Clock Setting Procedure — RBZ Radio . . . . . 252 ▫ Clock Setting Procedure — RER/REN Radio . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Using This Feature . . . . . . . . . . . . . . . . . . . 278 ▫ Controlling The iPod威 Using Radio Buttons . 278 ▫ Play Mode . . . . . . . . . . . . . . . . . . . . . . . . . 279 ▫ List Or Browse Mode . . . . . . . . . . . . . . . . . 280 䡵 Uconnect™ Multimedia (Satellite Radio) — If Equipped (REN/RER/RES Radios Only) . . 282 ▫ System Activation . . . . . . . . . . . . . . . . . . . . 282 ▫ Electronic Serial Number/Sirius Identification Number (ESN/SID) . . . . . . . . .
212 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Manual Air Conditioning And Heating System . . . . . . . . . . . . . . . . . . . . . . . . . . . . 293 ▫ Automatic Temperature Control — If Equipped . . . . . . . . . . . . . . . . . . . . . . 296 ▫ Operating Tips . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 213 INSTRUMENT PANEL FEATURES 4 1 — Air Outlet 2 — Instrument Cluster 3 — Hazard Switch 4 — Analog Clock 5 — Electronic Stability Program Off Button* / Traction Control System Off Button* 6 — Glove Compartment 7 — Radio 8 — Climate Control 9 — Heated Seat Switch* 10 — Power Outlet 11 — Ash Tray* 12 — Storage Compartment* 13 — Ignition Switch 14 — Hood Release 15 — Trunk Release Button 16 — Headlight Switch * If Equipped
214 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER — BASE
UNDERSTANDING YOUR INSTRUMENT PANEL 215 INSTRUMENT CLUSTER — PREMIUM 4
216 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTIONS NOTE: • A continuous chime will sound if the vehicle is driven more than 1 mile (1.6 km) with either turn signal on. 1. Electronic Speed Control / Adaptive Cruise Control (ACC) Indicator Light — If Equipped This light will turn on when the electronic • Check for an inoperative outside light bulb if either indicator flashes at a rapid rate. speed control or Adaptive Cruise Control (ACC) is ON. 5. Speedometer Indicates vehicle speed.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: U.S. Federal regulations require that upon transfer of vehicle ownership, the seller certify to the purchaser the correct mileage that the vehicle has been driven. If your odometer needs to be repaired or serviced, the repair technician should leave the odometer reading the same as it was before the repair or service.
218 UNDERSTANDING YOUR INSTRUMENT PANEL gASCAP If the vehicle diagnostic system determines that the fuel filler cap is loose, improperly installed, or damaged, a “gASCAP” message will display in the odometer display area. Tighten the fuel filler cap properly and press the TRIP ODOMETER button to turn off the message. If the problem continues, the message will appear the next time If the odometer displays the “tCASE” warning message the vehicle is started.
UNDERSTANDING YOUR INSTRUMENT PANEL 219 damaged, a “noFUSE” message will display in the odom- reset the oil change indicator system (after performing eter display area. For further information on fuses and the scheduled maintenance) perform the following profuse locations refer to “Fuses” in “Maintaining Your cedure: Vehicle”. 1. Place the ignition switch in the RUN position. (Do CHAngE OIL not start the engine). Your vehicle is equipped with an engine oil change 2.
220 UNDERSTANDING YOUR INSTRUMENT PANEL 9. Anti-Lock Brake (ABS) Light — If Equipped 7. Tachometer The red segments indicate the maximum permissible This light monitors the Anti-Lock Brake System (ABS). The light will turn on when the ignition engine revolutions per minute (RPM x 1000) for each gear range. Ease up on the accelerator before reaching the red switch is placed in the RUN position and may stay on for as long as four seconds. area. 8.
UNDERSTANDING YOUR INSTRUMENT PANEL 10. Electronic Stability Program (ESP) / Brake Assist System (BAS) Malfunction Indicator Light The yellow Electronic Stability Program (ESP) / Brake Assist System (BAS) Malfunction Indicator Light will turn on when the key in the ignition switch is placed in the RUN position. The light should go out with the engine running. The system will turn this light on continuously while the engine is running if it detects a malfunction in either the ESP, the BAS or both.
222 UNDERSTANDING YOUR INSTRUMENT PANEL 12. Brake Warning Light This light monitors various brake functions, including brake fluid level and parking brake application. If the brake light turns on, it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the anti-lock brake system reservoir.
UNDERSTANDING YOUR INSTRUMENT PANEL 223 Vehicles equipped with the Anti-Lock Brake System 13. Electronic Stability Program (ESP) / Traction (ABS), are also equipped with Electronic Brake Force Control System (TCS) Indicator Light — If Equipped If this indicator light flashes during acceleraDistribution (EBD). In the event of an EBD failure, the tion, ease up on the accelerator and apply as Brake Warning Light will turn on along with the ABS little throttle as possible. Adapt your speed and Light.
224 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! Driving with a hot engine cooling system could damage your vehicle. If the temperature gauge reads “H,” pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the “H,” and you hear continuous chimes, turn the engine OFF immediately and call for service. WARNING! A hot engine cooling system is dangerous.
UNDERSTANDING YOUR INSTRUMENT PANEL 16. High Beam Indicator This indicator will turn on when the high beam headlights are ON. Push the multifunction lever away from the steering wheel to switch the headlights to high beam. 17. Shift Lever Indicator The Shift Lever Indicator is self-contained within the instrument cluster. It displays the gear position of the automatic transmission. 18.
226 UNDERSTANDING YOUR INSTRUMENT PANEL turn off. If the light remains lit with the engine running, vehicle placard or tire inflation pressure label, you should your vehicle will usually be drivable. However, see an determine the proper tire inflation pressure for those tires.) authorized dealer for service as soon as possible. If the light is flashing when the engine is running, immediate service is required.
UNDERSTANDING YOUR INSTRUMENT PANEL 227 maintain correct tire pressure, even if under-inflation has tires or wheels on your vehicle to ensure that the replacenot reached the level to trigger illumination of the TPMS ment or alternate tires and wheels allow the TPMS to continue to function properly. low tire pressure telltale. Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly.
228 UNDERSTANDING YOUR INSTRUMENT PANEL 23. Charging System Light This light shows the status of the electrical charging system. The light should come on when the ignition switch is first placed in the RUN position and remain on briefly as a bulb check. If the light stays on or comes on while driving, turn off some of the vehicle’s non-essential electrical devices or increase engine speed (if at idle).
UNDERSTANDING YOUR INSTRUMENT PANEL WARNING! A malfunctioning catalytic converter, as referenced above, can reach higher temperatures than in normal operating conditions. This can cause a fire if you drive slowly or park over flammable substances such as dry plants or wood or cardboard, etc. This could result in death or serious injury to the driver, occupants or others. 229 Do not operate the vehicle until the cause is corrected. This light does not indicate how much oil is in the engine.
230 UNDERSTANDING YOUR INSTRUMENT PANEL ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) — IF EQUIPPED The Electronic Vehicle Information Center (EVIC) features a driver-interactive display that is located in the instrument cluster. This system conveniently allows the driver to select a variety of useful information by pressing the switches mounted on the steering wheel.
UNDERSTANDING YOUR INSTRUMENT PANEL 231 • Surround Sound modes (if equipped with DriverSelectable Surround [DSS]) Press the SCROLL button to scroll through Trip Functions, Navigation (if equipped), System Status Messages, and Personal Settings The system allows the driver to select information by (Customer-Programmable Features). The pressing the following buttons mounted on the steering SCROLL SCROLL button also functions as a remote Button wheel. sound system control.
232 UNDERSTANDING YOUR INSTRUMENT PANEL Electronic Vehicle Information Center (EVIC) • Memory System Disabled – Vehicle Not In PARK (with Displays a single chime) When the appropriate conditions exist, the EVIC displays • Memory System Disabled – Seat Belt Buckled (with a the following messages: single chime) • Turn Signal On (with a continuous warning chime if • Personal Settings Not Available – Vehicle Not in PARK the vehicle is driven more than 1 mile [1.
UNDERSTANDING YOUR INSTRUMENT PANEL 233 • SERVICE AWD SYSTEM — All Wheel Drive (AWD) • ACC Set — After setting the desired speed in the ACC system is not functioning properly and service is system. Refer to “Adaptive Cruise Control (ACC)” in required. “Understanding The Features Of Your Vehicle” (if equipped). • Normal Cruise Ready — When Adaptive Cruise Control (ACC) system is turned off and Normal (Fixed • ACC Cancelled — To disable the ACC system.
234 UNDERSTANDING YOUR INSTRUMENT PANEL • Distance Set — After changing the desired following • ACC Unavailable — If the ACC system turns off due distance in the ACC system, this message will display to a temporary malfunction that limits functionality. momentarily. Refer to “Adaptive Cruise Control Refer to “Adaptive Cruise Control (ACC)” in “Under(ACC)” in “Understanding The Features Of Your standing The Features Of Your Vehicle” (if equipped). Vehicle” (if equipped).
UNDERSTANDING YOUR INSTRUMENT PANEL • Channel # Trained • Clearing Channels • Channels Cleared • Did Not Train 235 • Check TPM System (with a single chime). Refer to information on “Tire Pressure Monitor” under “Starting And Operating.” • Check Gascap (refer to “Adding Fuel” in “Starting And Operating”) • Left Front Low Pressure (with a single chime).
236 UNDERSTANDING YOUR INSTRUMENT PANEL Oil Change Required Your vehicle is equipped with an engine oil change indicator system. The “Oil Change Required” message will flash in the EVIC display for approximately 10 seconds after a single chime has sounded to indicate the next scheduled oil change interval. The engine oil change indicator system is duty cycle based, which means the engine oil change interval may fluctuate dependent upon your personal driving style. 2.
UNDERSTANDING YOUR INSTRUMENT PANEL 237 • Display Units of Measure in will appear whenever MDS (if equipped) allows the engine to operate on four cylinders, or if you are driving Press the SCROLL button to cycle through all the Trip in a fuel efficient manner. Computer functions. The Trip Functions mode displays the following information. • Average Fuel Economy / Fuel Saver Mode — If Equipped Shows the average fuel economy since the last reset.
238 UNDERSTANDING YOUR INSTRUMENT PANEL This feature allows you to monitor when you are driving • Distance To Empty (DTE) in a fuel efficient manner, and it can be used to modify Shows the estimated distance that can be traveled with driving habits in order to increase fuel economy. the fuel remaining in the tank. This estimated distance is determined by a weighted average of the instantaneous and average fuel economy, according to the current fuel tank level.
UNDERSTANDING YOUR INSTRUMENT PANEL 239 • Trip A To Reset The Display Shows the total distance traveled for Trip A since the last Reset will only occur while a resettable function is being displayed. Press and release the FUNCTION SELECT reset. button once to clear the resettable function being dis• Trip B played. To reset all resettable functions, press and release Shows the total distance traveled for Trip B since the last the FUNCTION SELECT button a second time within reset.
240 UNDERSTANDING YOUR INSTRUMENT PANEL Keyless Go Display — If Equipped When the ENGINE START/STOP button is pressed to change ignition switch positions, the Keyless Go icon momentarily appears in the EVIC display showing the new ignition switch position. The round symbol in the middle rotates to point at the new ignition switch position. If desired, the ignition switch position graphic can be set to be constantly visible by pressing the EVIC MENU button until the display appears.
UNDERSTANDING YOUR INSTRUMENT PANEL 241 When the vehicle automatically transitions from AWD to Automatic All Wheel Drive (AWD) Displays — If RWD the EVIC will display the following message for Equipped Automatic AWD operation could be activated by outside five seconds. temperature, wheel slip, or other predetermined conditions, when the vehicle automatically transitions from RWD to AWD the EVIC will display the following message for five seconds.
242 UNDERSTANDING YOUR INSTRUMENT PANEL Driver-Selectable Surround Sound (DSS) – If Compass Display The compass readings indicate the direction Equipped Press and release the MENU button until “Surround the vehicle is facing. Press and release the Sound” displays in the EVIC. The EVIC provides inforHOME button to display one of eight compass mation on the current surround mode. HOME readings and the outside temperature.
UNDERSTANDING YOUR INSTRUMENT PANEL 243 degree turns (in an area free from large metal or metallic 5. Complete one or more 360 degree turns (in an area free objects) until the “CAL” message displayed in the EVIC from large metal or metallic objects) until the “CAL” message turns off. The compass will now function turns off. The compass will now function normally. normally.
244 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Keep magnetic materials away from the top of the instrument panel, such as iPod’s, Cell Phones, Laptops and Radar Detectors. This is where the compass module is located, and it can cause interference with the compass sensor, and it may give false readings. 2. Press and hold the HOME button for approximately two seconds. 3. Press the SCROLL button until “Compass Variance” message and the last variance zone number displays in the EVIC. 4.
UNDERSTANDING YOUR INSTRUMENT PANEL 245 used to select an item, and the AUDIO MODE button can Press and release the MENU button until Personal Setbe used to return to the previous menu. When the Map tings displays in the EVIC. display is active, pressing the FUNCTION SELECT butUse the SCROLL button to display one of the following ton will change the Navigation Unit Display to the Menu. choices.
246 UNDERSTANDING YOUR INSTRUMENT PANEL “Lock Doors Automatically at 15 mph (24 km/h)” When ON is selected, all doors will lock automatically when the vehicle reaches a speed of 15 mph (24 km/h). To make your selection, press and release the FUNCTION SELECT button until “ON” or “OFF” appears. the doors will unlock on the first press of the RKE transmitter UNLOCK button. To make your selection, press and release the FUNCTION SELECT button until “Driver Door 1st Press” or “All Doors 1st Press” appears.
UNDERSTANDING YOUR INSTRUMENT PANEL “Recall Memory with Remote Key Unlock” — If Equipped When ON is selected, you can use your RKE transmitter to recall one of two pre-programmed memory profiles. Each memory profile contains desired position settings for the driver seat, side mirror, adjustable pedals (if equipped), power tilt and telescopic steering column (if equipped), and a set of desired radio station presets.
248 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: The seat will return to the memorized seat location (if Recall Memory with Remote Key Unlock is set to ON) when the RKE transmitter is used to unlock the door. Refer to “Driver Memory Seat” in “Understanding The Features Of Your Vehicle” for further information. off if they were turned on by this feature. To make your selection, press and release the FUNCTION SELECT button until “ON” or “OFF” appears.
UNDERSTANDING YOUR INSTRUMENT PANEL 249 position when the transmission is shifted out of RE- your selection, press and release the FUNCTION SEVERSE. To make your selection, press and release the LECT button until “Off,” “45 sec.,” “5 min.,” “10 min.,” FUNCTION SELECT button until “ON” or “OFF” “30 min.,” or “60 min.” appears. appears. “AWD System Displays” “Turn Headlights On with Remote Key Unlock” When in this display you may select “ON” or “OFF”.
250 UNDERSTANDING YOUR INSTRUMENT PANEL “Confirmation of Voice Commands” — If Equipped When ON is selected, all voice commands from the Uconnect™ system are confirmed. To make your selection, press and release the FUNCTION SELECT button until “ON” or “OFF” appears. “Park Assist System” — If Equipped When ON is selected, the system will scan for objects behind the vehicle when the transmission is in the REVERSE or NEUTRAL position.
UNDERSTANDING YOUR INSTRUMENT PANEL “Passive Entry” — If Equipped The Passive Entry system is an enhancement to the vehicle’s Remote Keyless Entry (RKE) system. When ON is selected, this feature allows you to lock and unlock the vehicle’s door(s) without having to press the RKE transmitter lock or unlock buttons. To make your selection, press and release the FUNCTION SELECT button until “ON” or “OFF” appears.
252 UNDERSTANDING YOUR INSTRUMENT PANEL MEDIA CENTER 730N/430 (RER/REN/RBZ) — AM/FM STEREO RADIO AND CD/DVD/HDD/NAV — IF EQUIPPED NOTE: The sales code is located on the lower right side of the unit’s faceplate. Operating Instructions — Uconnect™ Phone — If Equipped Refer to “Uconnect™ Phone” in “Understanding The Features Of Your Vehicle”. Clock Setting Procedure — RBZ Radio The REN, RER and RBZ radios contain a CD/DVD To Manually Set the Clock player, USB port, and a 30-gigabyte hard drive (HDD). 1.
UNDERSTANDING YOUR INSTRUMENT PANEL 253 displayed. To move the minute backward, touch the Show Time if Radio is Off screen where the word “Min” with the arrow pointing When selected, this feature will display the time of day on the touch screen when the radio is turned off. Proceed downward is displayed. as follows to change the current setting: 5. To save the new time setting, touch the screen where 1. Turn on the radio. the word “Save” is displayed. Changing Daylight Savings Time 2.
254 UNDERSTANDING YOUR INSTRUMENT PANEL 3. Touch the screen where the words “Set Time Zone” are To Manually Set the Clock — RER/REN displayed. The time zone selection menu will appear on 1. Turn on the radio. the screen. 2. Touch the screen where the time is displayed. 4. Select a time zone by touching the screen where your selection appears. If you do not see a time zone that you 3.
UNDERSTANDING YOUR INSTRUMENT PANEL 255 6. To save the new time setting, touch the screen where 1. Turn on the radio. the word “Save” is displayed. 2. Touch the screen where the time is displayed. Changing Daylight Savings Time 3. Touch the screen where “User Clock” is displayed, the When selected, this feature will display the time of day in clock setting menu will appear on the screen. daylight savings time. Proceed as follows to change the 4.
256 UNDERSTANDING YOUR INSTRUMENT PANEL 4. Touch the screen where the words “Set Time Zone” are displayed. The time zone selection menu will appear on the screen. 5. Select a time zone by touching the screen where your selection appears. If you do not see a time zone that you want to select, touch the screen where the word “Page” is displayed to view additional time zones in the menu. 6. Touch the screen where the word “Save” is displayed.
UNDERSTANDING YOUR INSTRUMENT PANEL 257 Power Switch/Volume Control (Rotary) TIME Button Push the ON/VOLUME control knob to turn on the Press the TIME button to alternate display of the time radio. Push the ON/VOLUME control knob a second and radio frequency. time to turn off the radio. Clock Setting Procedure Electronic Volume Control 1. Press and hold the TIME button until the hours blink. The electronic volume control turns continuously (360 degrees) in either direction, without stopping. Turning 2.
258 UNDERSTANDING YOUR INSTRUMENT PANEL RW/FF Pressing the RW (Rewind) or FF (Fast Forward) buttons causes the tuner to search for the next frequency in the direction of the arrows. This feature operates in either AM or FM frequencies. Push the rotary TUNE/SCROLL control knob a third time and TREBLE will display. Turn the TUNE/SCROLL control knob to the right or left to increase or decrease the treble tones.
UNDERSTANDING YOUR INSTRUMENT PANEL SET/RND Button — To Set the Pushbutton Memory When you are receiving a station that you wish to commit to pushbutton memory, press the SET/RND button. The symbol SET 1 will now show in the display window. Select the button (1 to 6) you wish to lock onto this station and press and release that button. If a button is not selected within five seconds after pressing the SET/RND button, the station will continue to play but will not be stored into pushbutton memory.
260 UNDERSTANDING YOUR INSTRUMENT PANEL discs (CD-RW), compact discs with MP3 tracks and multisession compact discs with CD and MP3 tracks. Inserting Compact Disc(s) Gently insert one CD into the CD player with the CD label facing up. The CD will automatically be pulled into the CD player and the CD icon will illuminate on the radio display. If a CD does not go into the slot more than 1.0 in (2.5 cm), a disc may already be loaded and must be ejected before a new disc can be loaded.
UNDERSTANDING YOUR INSTRUMENT PANEL EJECT Button - Ejecting a CD Press the EJECT button to eject the CD. 261 the current selection. Pressing and holding the SEEK button will allow faster scrolling through the tracks in CD and MP3 modes. TIME Button Press this button to change the display from a large CD If you have ejected a disc and have not removed it within playing time display to a small CD playing time display. 10 seconds, it will be reloaded.
262 UNDERSTANDING YOUR INSTRUMENT PANEL Press the right SEEK button to move to the next ran- files properly and may be unable to play the file normally. UDF and Apple HFS formats are not supported. domly selected track. Press the RND button a second time to stop Random The radio uses the following limits for file systems: Play.
UNDERSTANDING YOUR INSTRUMENT PANEL 263 • Level 2: 31 (including a separator ⬙.⬙ and a three- rates (VBR) are also supported. The majority of MP3 files use a 44.1 kHz sampling rate and a 192, 160, 128, 96 or character extension) VBR bit rate. Multisession disc formats are supported by the radio. MPEG Sampling Multisession discs may contain combinations of normal Bit Rate (kbps) Specification Frequency (kHz) CD audio tracks and computer files (including MP3 files).
264 UNDERSTANDING YOUR INSTRUMENT PANEL Playback of MP3 Files When a medium containing MP3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3 files.
UNDERSTANDING YOUR INSTRUMENT PANEL MEDIA CENTER 130 (RES/RSC) — AM/FM STEREO RADIO WITH CD PLAYER (MP3 AUX JACK) AND SIRIUS RADIO 265 Operating Instructions — Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. NOTE: The radio sales code is located on the lower right Power Switch/Volume Control (Rotary) side of the radio faceplate. Push the ON/VOLUME control knob to turn on the radio. Push the ON/VOLUME control knob a second time to turn off the radio.
266 UNDERSTANDING YOUR INSTRUMENT PANEL to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations without stopping until you release it. Phone Button Uconnect™ Phone — If Equipped Press this button to operate the Uconnect™ Phone feature (if equipped). Refer to “Uconnect™ Phone” in “Understanding The Features If Your Vehicle”.
UNDERSTANDING YOUR INSTRUMENT PANEL 267 3. After adjusting the hours, press the right side TUNE/ INFO Button SCROLL control knob to set the minutes. The minutes Press the INFO button for an RDS station (one with call letters displayed). The radio will return a Radio Text will begin to blink. message broadcast from an FM station (FM mode only). 4. Adjust the minutes using the right side TUNE/ SCROLL control knob.
268 UNDERSTANDING YOUR INSTRUMENT PANEL Push the rotary TUNE/SCROLL control knob a second Push the rotary TUNE/SCROLL control knob again to time and MID will display. Turn the TUNE/SCROLL exit setting tone, balance, and fade. control knob to the right or left to increase or decrease the MUSIC TYPE Button mid-range tones. Pressing this button once will turn on the Music Type Push the rotary TUNE/SCROLL control knob a third mode for five seconds. Pressing the MUSIC TYPE button time and TREBLE will display.
UNDERSTANDING YOUR INSTRUMENT PANEL Program Type Classic Rock College Country Foreign Language Information Jazz News Nostalgia Oldies Personality Public Rhythm and Blues Religious Music Religious Talk Rock 16-Digit Character Display Cls Rock College Country Language Inform Jazz News Nostalga Oldies Persnlty Public R&B Rel Musc Rel Talk Rock Program Type Soft Soft Rock Soft Rhythm and Blues Sports Talk Top 40 Weather 269 16-Digit Character Display Soft Soft Rck Soft R&B Sports Talk Top 40 Weather By pr
270 UNDERSTANDING YOUR INSTRUMENT PANEL window. Select the button (1–6) you wish to lock onto this SETUP Button Pressing the SETUP button allows you to select between station and press and release that button. If a button is not selected within five seconds after pressing the SET/ the following items: RND button, the station will continue to play but will not • Set Clock — Pressing the SELECT button will allow be stored into pushbutton memory. you to set the clock.
UNDERSTANDING YOUR INSTRUMENT PANEL 271 Buttons 1 - 6 Inserting Compact Disc(s) These buttons tune the radio to the stations that you Gently insert one CD into the CD player with the CD commit to pushbutton memory (12 AM and 12 FM label facing up. The CD will automatically be pulled into stations). the CD player and the CD icon will illuminate on the radio display. If a CD does not go into the slot more than DISC/AUX Button 1.0 in (2.
272 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! (Continued) • Do not use adhesive labels. These labels can peel away and jam the player mechanism. • RES is a single CD player. Do not attempt to insert a second CD if one is already loaded. • Dual-media disc types (one side is a DVD, the other side is a CD) should not be used, and they can cause damage to the player. EJECT Button - Ejecting a CD Press the EJECT button to eject the CD.
UNDERSTANDING YOUR INSTRUMENT PANEL AM/FM Button Press the button to select either AM or FM mode. SET/RND Button (Random Play Button) Press this button while the CD is playing to activate Random Play. This feature plays the selections on the compact disc in random order to provide an interesting change of pace. 273 Supported Media (Disc Types) The MP3 file recording media supported by the radio are CDDA, CD-R, CD-RW, MP3, and CDDA+MP3.
274 UNDERSTANDING YOUR INSTRUMENT PANEL a number instead. With a maximum number of files, exceeding 20 folders will result in this display. With 200 files, exceeding 50 folders will result in this display.) Supported MP3 File Formats The radio will recognize only files with the *.MP3 extension as MP3 files. Non-MP3 files named with the *.MP3 extension may cause playback problems.
UNDERSTANDING YOUR INSTRUMENT PANEL MPEG Specification MPEG-2 Audio Layer 3 Sampling Frequency (kHz) Bit Rate (kbps) 24, 22.
276 UNDERSTANDING YOUR INSTRUMENT PANEL begin playing the files contained in that folder (or the Operation Instructions - Auxiliary Mode next folder in sequence if the selection does not contain The auxiliary (AUX) jack is an audio input jack which allows the user to plug in a portable device such as an playable files). MP3 player or cassette player and utilize the vehicle’s The folder list will time out after five seconds.
UNDERSTANDING YOUR INSTRUMENT PANEL 277 This feature allows an iPod威 to be plugged into the Operating Instructions - Uconnect™ Phone (If vehicle’s sound system through a 16–pin connector, using Equipped) Refer to “Uconnect™ Phone” in “Understanding The the provided interface cable. Features If Your Vehicle”. UCI supports Mini, 4G, Photo, Nano, 5G iPod威 and iPhone威 devices. Some iPod威 software versions may not Operating Instructions - Uconnect™ Multimedia fully support the UCI features.
278 UNDERSTANDING YOUR INSTRUMENT PANEL Connecting The iPod姞 Use the provided connection cable to connect an iPod威 to the vehicle’s 16–pin connector port (which is located in the glove compartment on some vehicles). Once the iPod威 is connected and synchronized to the vehicle’s UCI system (iPod威 may take a few seconds to connect), the iPod威 starts charging and is ready for use by pressing radio switches, as described below.
UNDERSTANDING YOUR INSTRUMENT PANEL Play Mode When switched to UCI mode, the iPod威 automatically starts Play mode. In Play mode, use the following buttons on the radio faceplate to control the iPod威 and display data: • Use the TUNE control knob to select the next or previous track. • Turning it clockwise (forward) by one click, while playing a track, skips to the next track. 279 • Jump backward in the current track by pressing and holding the << RW button.
280 UNDERSTANDING YOUR INSTRUMENT PANEL • While a track is playing, press the INFO button to see • RND button (available on sales code RES radio only): the associated metadata (artist, track title, album, etc.) Pressing this button toggles between Shuffle ON and for that track. Pressing the INFO button again jumps Shuffle OFF modes for the iPod威. If the RND icon is to the next screen of data for that track.
UNDERSTANDING YOUR INSTRUMENT PANEL 281 fast will scroll through the list faster. During fast scroll, a slight delay in updating the information on the radio display may be noticed. • Pressing a PRESET button will display the current list on the top line and the first item in that list on the second line. • During all List modes, the iPod威 displays all lists in “wrap-around” mode. So if the track is at the bottom of the list, just turn the wheel backwards (counter-clockwise) to get to the track faster.
282 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! • Leaving the iPod威 (or any supported device) anywhere in the vehicle in extreme heat or cold can alter the operation or damage the device. Follow the device manufacturer’s guidelines. • Placing items on the iPod威, or connections to the iPod威 in the vehicle, can cause damage to the device and/or to the connectors. WARNING! Do not plug in or remove the iPod威 while driving. Failure to follow this warning could result in an accident.
UNDERSTANDING YOUR INSTRUMENT PANEL 283 information, call the toll-free number 888-539-7474, or Sirius ID number will display. The Sirius ID number visit the Sirius web site at www.sirius.com, or at www- display will time out in two minutes. Press any button on the radio to exit this screen. .siriuscanada.ca for Canadian residents.
284 UNDERSTANDING YOUR INSTRUMENT PANEL bikes should be placed as far rearward as possible, within Operating Instructions - Uconnect™ Multimedia the loading design of the rack. Do not place items directly (Satellite) Mode on or above the antenna. NOTE: The ignition switch must be in the ON or ACC position to operate the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL INFO Button Pressing the INFO button will cycle the display information between Artist, Song Title, and Composer (if available). Also, pressing and holding the INFO button for an additional three seconds will make the radio display the Song Title all of the time (press and hold again to return to normal display). 285 MUSIC TYPE Button Pressing this button once will turn on the Music Type mode for five seconds.
286 UNDERSTANDING YOUR INSTRUMENT PANEL the SET button twice and SET 2 will show in the display SETUP Button Pressing the SETUP button allows you to select the window. Each button can be set for SET 1 and SET 2. This allows a total of 12 Satellite channels to be stored into following items: pushbutton memory. The channels stored in SET 2 • Display Sirius ID number — Press the AUDIO/ memory can be selected by pressing the pushbutton SELECT button to display the Sirius ID number. This twice.
UNDERSTANDING YOUR INSTRUMENT PANEL KICKER姞 HIGH PERFORMANCE SOUND SYSTEM WITH DRIVER-SELECTABLE SURROUND (DSS) – IF EQUIPPED 287 any stereo audio source. A new feature of the KICKER威 audio system offers the ability to choose surround sound for any audio source. “Audio Surround” is optimized for front seat passengers for any audio source.
288 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Dependent on the audio source, the output may sound better in stereo or DDS surround mode. When in “Audio Surround” mode, balance is set automatically. Fader control is available to add more surround audio if desired. VIDEO ENTERTAINMENT SYSTEM (VES)™ — IF EQUIPPED The optional Video Entertainment System (VES)™ includes the following components for rear seat entertainment: • A diagonal 7 in (17.
UNDERSTANDING YOUR INSTRUMENT PANEL 289 • A battery-powered infrared remote control snaps into a molded compartment in the center console armrest upper storage bin. 4 VES™ Video Screen NOTE: Close the armrest after the LCD screen has been raised to its viewing position.
290 UNDERSTANDING YOUR INSTRUMENT PANEL Audio/Video RCA Jacks (AUX Jacks) on the rear of the center console enable the monitor to display video directly from a video camera, connect video games for display on the screen, or play music directly from an MP3 player. REMOTE SOUND SYSTEM CONTROLS — IF EQUIPPED The remote sound system controls are located on the surface of the steering wheel at the three and nine o’clock positions. 1. Video in (yellow) 2. Left audio in (white) 3.
UNDERSTANDING YOUR INSTRUMENT PANEL Vehicles equipped with steering wheel-mounted buttons are also equipped with the Electronic Vehicle Information Center (EVIC). The EVIC features a driver-interactive display which is located in the instrument cluster. The VOLUME button controls the sound level of the sound system. Press the top of the VOLUME button to increase the sound level. VOLUME Press the bottom of the VOLUME button to Button decrease the sound level.
292 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: If you experience difficulty in playing a particuCD/DVD DISC MAINTENANCE To keep a CD/DVD in good condition, take the following lar disc, it may be damaged (i.e., scratched, reflective precautions: coating removed, a hair, moisture or dew on the disc) oversized, or have protection encoding. Try a known 1. Handle the disc by its edge; avoid touching the good disc before considering disc player service. surface. 2.
UNDERSTANDING YOUR INSTRUMENT PANEL Manual Air Conditioning and Heating System 293 Blower Control The rotary knob on the left controls the blower. The control has an OFF position and four speed settings. The blower will remain on until the control is turned to the OFF position or the ignition is turned OFF. NOTE: For vehicles equipped with Remote Start, the climate controls will not function during Remote Start operation if the blower control is left in the “O” (Off) position.
294 UNDERSTANDING YOUR INSTRUMENT PANEL Temperature Control The rotary knob in the center controls air temperature. Rotate the control to the left for cooler air temperature and to the right for warmer air temperature. Rotating the control to the extreme left provides the coldest setting. Rotating the control to the extreme right provides the warmest setting. Mode Control • Defrost Air is directed to the windshield through the outlets at the base of the windshield.
UNDERSTANDING YOUR INSTRUMENT PANEL • Bi-Level Air flows through the outlets located in the instrument panel and through the outlets located on the floor. Air flows through the registers in the back of the center console to the rear seat passengers. These registers can be closed to partially block airflow. 295 re-used. Use this mode to cool the inside of the vehicle rapidly. The Recirculation mode can also be used to temporarily block out outside odors, smoke, and dust.
296 UNDERSTANDING YOUR INSTRUMENT PANEL Automatic Temperature Control — If Equipped Automatic Temperature Controls Operation of the system is quite simple. Begin by turning the mode control knob (on the right) to AUTO, and place the blower control knob (on the left) to either LO AUTO or HI AUTO. The LO AUTO position should be used for front seat occupants only. The HI AUTO position should be used when more airflow is desired, or when rear seat occupants are present.
UNDERSTANDING YOUR INSTRUMENT PANEL 297 72°F (22°C) is the recommended setting for maximum illuminate. After 10 minutes, the system will return to comfort for the average person; however, this may vary. normal AUTO mode function and the indicator will turn off. NOTE: The temperature setting can be adjusted at any NOTE: time without affecting automatic operation. • The surface of the climate control panel and the top Air conditioning in this system is automatic.
298 UNDERSTANDING YOUR INSTRUMENT PANEL Attempting to use the recirculation while in these modes will cause the indicator in the control button to blink and then turn off. Manual Operation This system offers a full complement of manual override features, which consist of blower preferred automatic, mode preferred automatic, or blower and mode preferred automatic. This means the operator can override the blower, the mode, or both.
UNDERSTANDING YOUR INSTRUMENT PANEL 299 4
300 UNDERSTANDING YOUR INSTRUMENT PANEL The operator can override the AUTO mode setting to • Bi-Level change airflow distribution by rotating the mode control Air flows through the outlets located in the instruknob (on the right) to one of the following positions. ment panel and through the outlets located on the floor. Air flows through the registers in the back of the • Defrost center console to the rear seat passengers.
UNDERSTANDING YOUR INSTRUMENT PANEL 301 NOTE: To control the air conditioning manually, the Attempting to use the recirculation while in these modes mode selector must be moved out of the AUTO position. will cause the indicator in the control button to blink and then turn off. • Recirculation Control This button can be used to block out smoke, Operating Tips odors, dust, high humidity, or if rapid cooling NOTE: Refer to the chart at the end of this section for is desired.
302 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Recirculate without A/C should not be used for Winter Operation Use of the air Recirculation mode during Winter months long periods, as fogging may occur. is not recommended because it may cause window Outside Air Intake fogging. Make sure the air intake, located directly in front of the Vacation Storage windshield, is free of obstructions such as leaves.
UNDERSTANDING YOUR INSTRUMENT PANEL 303 Control Setting Suggestions for Various Weather Conditions 4
STARTING AND OPERATING CONTENTS 䡵 Starting Procedures . . . . . . . . . . . . . . . . . . . . 309 䡵 Automatic Transmission . . . . . . . . . . . . . . . . . 314 ▫ Automatic Transmission . . . . . . . . . . . . . . . 309 ▫ General Information . . . . . . . . . . . . . . . . . . 315 ▫ Keyless Go™ . . . . . . . . . . . . . . . . . . . . . . . 310 ▫ Key Ignition Park Interlock . . . . . . . . . . . . . 317 ▫ Normal Starting . . . . . . . . . . . . . . . . . . . . .
306 STARTING AND OPERATING ▫ Five-Speed Automatic Transmission – If Equipped . . . . . . . . . . . . . . . . . . . . . . . 324 ▫ Power Steering Fluid Check . . . . . . . . . . . . . 334 ▫ Gear Ranges . . . . . . . . . . . . . . . . . . . . . . . . 324 䡵 Multi-Displacement System (MDS) (If Equipped) – 5.7L Engine Only . . . . . . . . . . . 335 䡵 AutoStick威 — If Equipped . . . . . . . . . . . . . . . 328 䡵 Parking Brake . . . . . . . . . . . . . . . . . . . . . . . . 335 ▫ Operation . . . . . . . . .
STARTING AND OPERATING 䡵 Tire Safety Information 307 . . . . . . . . . . . . . . . . . 345 ▫ Tread Wear Indicators . . . . . . . . . . . . . . . . . 360 ▫ Tire Markings . . . . . . . . . . . . . . . . . . . . . . . 345 ▫ Life Of Tire . . . . . . . . . . . . . . . . . . . . . . . . 361 ▫ Tire Identification Number (TIN) . . . . . . . . . 349 ▫ Replacement Tires . . . . . . . . . . . . . . . . . . . . 362 ▫ Tire Terminology And Definitions . . . . . . . . . 350 䡵 Self-Sealing Tires — If Equipped . .
308 STARTING AND OPERATING ▫ Reformulated Gasoline . . . . . . . . . . . . . . . . 375 ▫ Gross Axle Weight Rating (GAWR) . . . . . . . . 382 ▫ Gasoline/Oxygenate Blends . . . . . . . . . . . . . 375 ▫ Overloading . . . . . . . . . . . . . . . . . . . . . . . . 383 ▫ E85 Usage In Non-Flex Fuel Vehicles . . . . . . 376 ▫ Loading . . . . . . . . . . . . . . . . . . . . . . . . . . . 383 ▫ MMT In Gasoline . . . . . . . . . . . . . . . . . . . . 377 䡵 Trailer Towing . . . . . . . . . . . . . . . . . . .
STARTING AND OPERATING STARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust the inside and outside mirrors, fasten your seat belt, and if present, instruct all other occupants to buckle their seat belts. WARNING! Never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Do not leave the key fob in the ignition switch.
310 STARTING AND OPERATING Do not press the accelerator. Use the Fob with Integrated Key to briefly turn the ignition switch to the START position and release it as soon as the starter engages. The starter motor will continue to run, and it will disengage automatically when the engine is running. If the engine fails to start, the starter will disengage automatically in 10 seconds.
STARTING AND OPERATING 311 NOTE: The ENGINE START/STOP button should only To Turn Off the Engine Using ENGINE be removed or inserted with the ignition in the LOCK START/STOP Button position (OFF position for Keyless Go™). 1. Place the shift lever in PARK, then press and release the ENGINE START/STOP button. Normal Starting Using the ENGINE START/STOP Button 2. The ignition switch will return to the OFF position. NOTE: Normal starting of either a cold or a warm 3.
312 STARTING AND OPERATING NOTE: If the ignition switch is left in the ACC or RUN (engine not running) position and the transmission is in PARK, the system will automatically time out after 60 minutes of inactivity and the ignition will switch to the OFF position. Keyless Go™ Functions – With Driver’s Foot OFF the Brake Pedal Pedal (In PARK or NEUTRAL Position) The Keyless Go™ feature operates similar to an ignition switch. It has four positions, OFF, ACC, RUN and START.
STARTING AND OPERATING WARNING! (Continued) • Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transmission cannot be started this way. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle. If the vehicle has a discharged battery, booster cables may be used to obtain a start from a booster battery or the battery in another vehicle.
314 STARTING AND OPERATING CAUTION! WARNING! To prevent damage to the starter, wait 10 to 15 seconds before trying again. Remember to disconnect the cord before driving. Damage to the 110-115 Volt electrical cord could cause electrocution. After Starting The idle speed is controlled automatically and it will AUTOMATIC TRANSMISSION decrease as the engine warms up. ENGINE BLOCK HEATER — IF EQUIPPED The engine block heater warms the engine, and permits quicker starts in cold weather.
STARTING AND OPERATING CAUTION! (Continued) • Do not shift from REVERSE, PARK, or NEUTRAL into any forward gear when the engine is above idle speed. • Before shifting into any gear, make sure your foot is firmly on the brake pedal. WARNING! It is dangerous to move the shift lever out of PARK or NEUTRAL if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in reverse.
316 STARTING AND OPERATING NOTE: • After selecting any driving position, wait a moment to allow the gear to engage fully before accelerating, especially when the engine is cold. The shift lever is automatically locked while in the PARK position. To move the shift lever out of the PARK position, the brake pedal must be firmly pressed before the shift lock will release.
STARTING AND OPERATING WARNING! Unintended movement of a vehicle could injure those in and near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, you should always shift the transmission into PARK, remove the key fob from the ignition, and apply the parking brake. Once the key fob is removed from the ignition, the shift lever is locked in the PARK position, securing the vehicle against unwanted movement.
318 STARTING AND OPERATING Brake/Transmission Interlock Manual Override There is an override for the BTSI that allows you to move the shift lever out of the PARK position if an electrical system malfunction occurs (i.e., dead battery). To access the override, remove the rubber tray from the storage bin located to the right of the shift lever. The override access port is at the top of the bin to the right of the shift lever gate. 1.
STARTING AND OPERATING 319 With Keyless Go™ – If Equipped If the engine is running, press the START/STOP button to turn it off. Release the brake pedal and press the START/ STOP button once or twice to go to the ACC or RUN position. Do not start the engine. Then, follow the instructions shown above to activate the override.
320 STARTING AND OPERATING When parking on a flat surface, place the shift lever in the • When shifting into PARK move the shift lever all the PARK position first, and then apply the parking brake. way forward and left until it stops and is fully seated. When parking on a hill, it is important to set the parking • Look at the shift indicator display on the instrument panel to ensure it is in the PARK position.
STARTING AND OPERATING NEUTRAL This range is used when the vehicle is standing for prolonged periods with the engine running. The engine may be started in this range. Set the parking brake if you must leave the vehicle. CAUTION! Coasting the vehicle or driving for any other reason with shift lever in NEUTRAL can result in transmission damage. WARNING! Do not coast in NEUTRAL and never turn off the ignition to coast down a hill.
322 STARTING AND OPERATING • If the transmission temperature gets too hot, the occur only to prevent engine overspeed while downshifts transmission may downshift out of Overdrive or en- occur earlier than in other gear range selections. gage Overdrive at higher vehicle speeds until the CAUTION! transmission cools down. After cooldown, Overdrive will resume normal operation.
STARTING AND OPERATING NOTE: • The torque converter clutch will not engage until the transmission fluid and engine coolant is warm (usually after 1–3 miles [1.6–4.8 km] of driving). Because engine speed is higher when the torque converter clutch is not engaged, it may seem as if the transmission is not shifting into Overdrive when cold. This is considered a normal condition. Pulling the shift lever into the “3” position will show that the transmission is able to shift into and out of Overdrive.
324 STARTING AND OPERATING NOTE: Even if the transmission can be reset, we recommend that you visit an authorized dealer at your earliest possible convenience. Your authorized dealer has diagnostic equipment to determine if the problem could recur. If the transmission cannot be reset, authorized dealer service is required. Five-Speed Automatic Transmission – If Equipped Shifting from DRIVE to PARK or REVERSE should be done only after the accelerator pedal is released and the vehicle is stopped.
STARTING AND OPERATING 325 When parking on a flat surface, place the shift lever in the The following indicators should be used to ensure that PARK position first, and then apply the parking brake. you have engaged the shift lever in the PARK position: When parking on a hill, it is important to set the parking • When shifting into PARK, move the shift lever all the way forward and left until it stops and is fully seated.
326 STARTING AND OPERATING NEUTRAL This range is used when the vehicle is standing for prolonged periods with the engine running. The engine may be started in this range. Set the parking brake if you must leave the vehicle. CAUTION! Coasting the vehicle or driving for any other reason with shift lever in NEUTRAL can result in transmission damage. WARNING! Do not coast in NEUTRAL and never turn off the ignition to coast down a hill.
STARTING AND OPERATING 327 Temporary Transmission Limp Home Mode The transmission is monitored for abnormal conditions. If a condition is detected that could result in transmission damage, the transmission will engage Limp Home Mode. If vehicle acceleration worsens, or the transmission no longer shifts, the transmission is most likely operating in the Limp Home Mode. In this mode, the transmission will remain in the current gear until the vehicle is brought to a stop.
328 STARTING AND OPERATING in ERS mode, tapping the shift lever to the left (D-) or right (D+) will change the top available gear. The transmission will not shift above the indicated gear, but will shift up and down normally (automatically) through the lower gears.
STARTING AND OPERATING Operation When the shift lever is in the DRIVE position, the transmission will operate automatically, shifting between the five available gears. To engage AutoStick威, simply move the shift lever to the right or left (D+/D-) while in the DRIVE position. The gear position will display in the instrument cluster. In the AutoStick威 mode, the transmission will shift up and down when left or right (D-/D+) is manually selected by the driver.
330 STARTING AND OPERATING To maximize fuel economy, your AWD vehicle automatically defaults to rear-wheel drive (RWD) when road and environmental conditions are such that wheel slip is unlikely to occur. When specific road and environmental conditions require increased levels of road traction, the vehicle automatically shifts into AWD mode.
STARTING AND OPERATING WARNING! Rapid acceleration on slippery surfaces is dangerous. Unequal traction can cause sudden pulling of the rear wheels. You could lose control of the vehicle and possibly have an accident. Accelerate slowly and carefully whenever there is likely to be poor traction (ice, snow, wet mud, loose sand, etc.). Traction When driving on wet or slushy roads, it is possible for a wedge of water to build up between the tire and road surface.
332 STARTING AND OPERATING Flowing/Rising Water WARNING! Do not drive on or across a road or path where water is flowing and/or rising (as in storm run-off). Flowing water can wear away the road or path’s surface and cause your vehicle to sink into deeper water. Furthermore, flowing and/or rising water can carry your vehicle away swiftly. Failure to follow this warning may result in injuries that are serious or fatal to you, your passengers, and others around you.
STARTING AND OPERATING 333 CAUTION! (Continued) WARNING! • Driving through standing water may cause damage to your vehicle’s drivetrain components. Always inspect your vehicle’s fluids (i.e., engine oil, transmission, axle, etc.) for signs of contamination (i.e., fluid that is milky or foamy in appearance) after driving through standing water. Do not continue to operate the vehicle if any fluid appears contaminated, as this may result in further damage.
334 STARTING AND OPERATING POWER STEERING The standard power steering system will give you good vehicle response and increased ease of maneuverability in tight spaces. The system will provide mechanical steering capability if power assist is lost. If for some reason the power assist is interrupted, it will still be possible to steer your vehicle. Under these conditions, you will observe a substantial increase in steering effort, especially at very low vehicle speeds and during parking maneuvers.
STARTING AND OPERATING 335 apparent, and/or the system is not functioning as antici- If necessary, add fluid to restore to the proper indicated pated. Coordinate inspection efforts through an autho- level. With a clean cloth, wipe any spilled fluid from all surfaces. Refer to “Fluids, Lubricants, and Genuine rized dealer. Parts” in “Maintaining Your Vehicle” for further CAUTION! information.
336 STARTING AND OPERATING The foot operated parking brake is located below the lower left corner of the instrument panel. To apply the park brake, firmly push the park brake pedal fully. To release the parking brake, press the park brake pedal a second time and let your foot up as you feel the brake disengage. When the parking brake is applied with the ignition switch in the ON position, the “Brake Warning Light” in the instrument cluster will illuminate.
STARTING AND OPERATING make it difficult to move the shift lever out of PARK. The parking brake should always be applied whenever the driver is not in the vehicle. WARNING! • Never use the PARK position as a substitute for the parking brake. Always apply the parking brake fully when parked to guard against vehicle movement and possible injury or damage. • Never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons.
338 STARTING AND OPERATING ANTI-LOCK BRAKE SYSTEM The Anti-Lock Brake System (ABS) provides increased vehicle stability and brake performance under most braking conditions. The system automatically “pumps” the brakes during severe braking conditions to prevent wheel lock-up. ABS is activated during braking under certain road or stopping conditions. ABS-inducing conditions can include ice, snow, gravel, bumps, railroad tracks, loose debris, or panic stops.
STARTING AND OPERATING 339 WARNING! WARNING! (Continued) • The ABS contains sophisticated electronic equipment that may be susceptible to interference caused by improperly installed or high output radio transmitting equipment. This interference can cause possible loss of anti-lock braking capability. Installation of such equipment should be performed by qualified professionals. • Pumping of the Anti-Lock Brakes will diminish their effectiveness and may lead to an accident.
340 STARTING AND OPERATING ELECTRONIC BRAKE CONTROL SYSTEM Your vehicle is equipped with an advanced electronic brake control system that include Anti-Lock Brake System (ABS), Traction Control System (TCS), Brake Assist System (BAS), and the Electronic Stability Program (ESP). All four of these systems work together to enhance vehicle stability and control in various driving conditions.
STARTING AND OPERATING Brake Assist System (BAS) This system complements the ABS by optimizing the vehicle braking capability during emergency brake maneuvers. This system detects an emergency braking situation by sensing the rate and amount of brake application and then applies optimum pressure to the brakes. This can help reduce braking distances. Applying the brakes very quickly results in the best BAS assistance.
342 STARTING AND OPERATING power may also be reduced to assist in counteracting the flashes when the TCS is active. If the “ESP/TCS Indicator condition of oversteer or understeer and help the vehicle Light” begins to flash during acceleration, ease up on the accelerator and apply as little throttle as possible. Be sure maintain the desired path. to adapt your speed and driving to the prevailing road The ESP uses sensors in the vehicle to determine the path conditions.
STARTING AND OPERATING The ESP system has two available operating modes: ESP On This is the normal operating mode for the ESP. Whenever the vehicle is started, the ESP system will be in this mode. This mode should be used for most driving conditions. The ESP should only be turned OFF for specific reasons as noted in the following paragraphs. Partial Off The “Partial Off” mode is intended for times when a more spirited driving experience is desired.
344 STARTING AND OPERATING switch. Once the situation requiring “Partial Off” mode is ESP/BAS Malfunction Indicator Light and overcome, turn the ESP on again by momentarily press- ESP/TCS Indicator Light The Malfunction Indicator Light for the ESP is ing the ESP OFF switch. This may be done while the combined with the BAS indicator. The “ESP/ vehicle is in motion.
STARTING AND OPERATING 345 NOTE: TIRE SAFETY INFORMATION • The “ESP/TCS Indicator Light” and the “ESP/BAS Tire Markings Malfunction Indicator Light” will turn on momentarily each time the ignition switch is turned to the ON position. • Each time the ignition switch is turned to the ON position, the ESP system will be on even if it was turned off previously. • The ESP control system will make buzzing or clicking sounds when it is active.
346 STARTING AND OPERATING NOTE: • Temporary spare tires are high-pressure compact • P (Passenger) - Metric tire sizing is based on U.S. spares designed for temporary emergency use only. design standards. P-Metric tires have the letter “P” Tires designed to this standard have the letter “T” molded into the sidewall preceding the size designamolded into the sidewall preceding the size designation. Example: P215/65R15 95H. tion. Example: T145/80D18 103M.
STARTING AND OPERATING 347 Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ⴖ....blank....ⴖ = Passenger car tire based on European design standards LT = Light truck tire based on U.S. design standards T = Temporary spare tire 31 = Overall diameter in inches (in) 215 = Section width in millimeters (mm) 65 = Aspect ratio in percent (%) — Ratio of section height to section width of tire 10.
348 STARTING AND OPERATING EXAMPLE: Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions — The maximum speed corresponding to the speed symbol should only be achieved under specified operating conditions (i.e.
STARTING AND OPERATING Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full TIN, including the date code, located on the white sidewall side of the tire. 349 Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the outboard side, then you will find it on the inboard side of the tire.
350 STARTING AND OPERATING Tire Terminology and Definitions Term B-Pillar Cold Tire Pressure Maximum Inflation Pressure Recommended Inflation Pressure Tire Placard Definition The vehicle B-Pillar is a structural member of the body located between the front and rear door (of a four-door vehicle) running from the sill to the roof. Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or driven less than 1 mile (1.
STARTING AND OPERATING Tire Loading and Tire Pressure 351 Tire and Loading Information Placard Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar.
352 STARTING AND OPERATING Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the Tire and Loading Information placard and in the “Vehicle Loading” section of this manual.
STARTING AND OPERATING 353 4. The resulting figure equals the available amount of NOTE: cargo and luggage load capacity. For example, if “XXX” • The following table shows examples on how to calculate total load, cargo/luggage, and towing capacities amount equals 1,400 lbs (635 kg) and there will be five of your vehicle with varying seating configurations 150 lb (68 kg) passengers in your vehicle, the amount of and number and size of occupants.
354 STARTING AND OPERATING
STARTING AND OPERATING WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.
356 STARTING AND OPERATING WARNING! (Continued) • Unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • Always drive with each tire inflated to the recommended cold tire inflation pressure. Economy Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement.
STARTING AND OPERATING CAUTION! After inspecting or adjusting the tire pressure, always reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. 357 Tire pressures change by approximately 1 psi (7 kPa) per 12°F (7°C) of air temperature change. Keep this in mind when checking tire pressure inside a garage, especially in the Winter.
358 STARTING AND OPERATING Tire Pressures for High Speed Operation Radial Ply Tires The manufacturer advocates driving at safe speeds WARNING! within posted speed limits. Where speed limits or conditions are such that the vehicle can be driven at high Combining radial ply tires with other types of tires speeds, maintaining correct tire inflation pressure is very on your vehicle will cause your vehicle to handle important. Increased tire pressure and reduced vehicle poorly.
STARTING AND OPERATING 359 WARNING! CAUTION! Temporary use spare tires are for emergency use only. With these tires, do not drive more than 50 mph (80 km/h). Temporary use spare tires have limited tread life. When the tread is worn to the tread wear indicators, the temporary use spare tire needs to be replaced. Be sure to follow the warnings, which apply to your spare. Failure to do so could result in spare tire failure and loss of vehicle control.
360 STARTING AND OPERATING WARNING! WARNING! The limited-use spare tires are for emergency use only. Installation of this limited-use spare tire affects vehicle handling. With this tire, do not drive more than 50 mph (80 km/h). Keep inflated to the cold tire inflation pressure listed on either your tire placard or limited-use spare tire and wheel assembly. Replace (or repair) the original tire at the first opportunity and reinstall it on your vehicle.
STARTING AND OPERATING 361 Life of Tire The service life of a tire is dependent upon varying factors including, but not limited to: • Driving style • Tire pressure • Distance driven WARNING! 1 — Worn Tire 2 — New Tire Tires and the spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure. You could lose control and have an accident resulting in serious injury or death.
362 STARTING AND OPERATING Replacement Tires The tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for wear and correct cold tire inflation pressure. The manufacturer strongly recommends that you use tires equivalent to the originals in size, quality and performance when replacement is needed. (Refer to the paragraph on “Tread Wear Indicators”). Refer to the “Tire and Loading Information” placard for the size designation of your tire.
STARTING AND OPERATING WARNING! (Continued) • Failure to equip your vehicle with tires having adequate speed capability can result in sudden tire failure and loss of vehicle control. CAUTION! Replacing original tires with tires of a different size may result in false speedometer and odometer readings. 363 SNOW TIRES Some areas of the country require the use of snow tires during the winter.
364 STARTING AND OPERATING TIRE ROTATION RECOMMENDATIONS Tires on the front and rear axles of vehicles operate at different loads and perform different steering, driving, and braking functions. For these reasons, they wear at unequal rates. The suggested rotation method is the “forward cross” shown in the following diagram. This rotation pattern does not apply to some directional tires that must not be reversed. These effects can be reduced by timely rotation of tires.
STARTING AND OPERATING 365 TIRE PRESSURE MONITOR SYSTEM (TPMS) The Tire Pressure Monitor System (TPMS) will warn the driver of a low tire pressure based on the vehicle recommended cold placard pressure. The TPMS will warn the driver of a low tire pressure if the tire pressure falls below the low-pressure warning limit for any reason, including low temperature effects and natural pressure loss through the tire. The tire pressure will vary with temperature by about 1 psi (6.9 kPa) for every 12°F (6.5°C).
366 STARTING AND OPERATING For example, your vehicle may have a recommended cold (parked for more than three hours) placard pressure of 30 psi (207 kPa). If the ambient temperature is 68°F (20°C) and the measured tire pressure is 27 psi (186 kPa), a temperature drop to 20°F (-7°C) will decrease the tire pressure to approximately 23 psi (158 kPa). This tire pressure is sufficiently low enough to turn ON the TPM Telltale Light.
STARTING AND OPERATING NOTE: • The TPMS is not intended to replace normal tire care and maintenance or to provide warning of a tire failure or condition. • The TPMS should not be used as a tire pressure gauge while adjusting your tire pressure. • Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability.
368 STARTING AND OPERATING TPMS will only monitor the pressure in the full size spare when it is used in place of a road tire. Otherwise, a spare with a pressure below the low-pressure limit will not cause the TPM Telltale Light to illuminate or the chime to sound. Check TPMS Warning If a system fault is detected, the TPM Telltale Light will flash on and off for 75 seconds and then remain on solid. The system fault will also sound a chime.
STARTING AND OPERATING 369 2. If you install the compact spare tire in place of a road tire that has a pressure below the low-pressure warning 1. The matching full size spare wheel and tire assembly limit, upon the next ignition switch cycle, a chime will has a TPM sensor that can be monitored by the TPMS. sound and the TPM Telltale Light will turn ON. 2. If you install the full size spare in place of a road tire 3.
370 STARTING AND OPERATING Premium System – If Equipped The Tire Pressure Monitor System (TPMS) uses wireless technology with wheel rim mounted electronic sensors to monitor tire pressure levels. Sensors mounted to each wheel as part of the valve stem transmit tire pressure readings to the receiver module. NOTE: It is particularly important for you to check the tire pressure in all of the tires on your vehicle monthly and to maintain the proper pressure.
STARTING AND OPERATING 371 system receives the updated tire pressures, the system will automatically update, the graphic display in the EVIC will stop flashing, and the TPM Telltale Light will turn off. The vehicle may need to be driven for up to 20 minutes above 15 mph (25 km/h) in order for the TPMS to receive this information. Check TPMS Warning If a system fault is detected, the TPM Telltale Light will flash on and off for 75 seconds and then remain on solid. The system fault will also sound a chime.
372 STARTING AND OPERATING 1. Signal interference due to electronic devices or driving next to facilities emitting the same radio frequencies as the TPM sensors. 2. Installing aftermarket window tinting that contains materials that may block radio wave signals. 3. Accumulation of snow or ice around the wheels or wheel housings. 4. Using tire chains on the vehicle. 5. Using wheels/tires not equipped with TPM sensors.
STARTING AND OPERATING 373 EVIC will display a low pressure message and a graphic 3. After driving the vehicle for up to 20 minutes above showing the low tire pressure value flashing. 15 mph (25 km/h), the TPM Telltale Light will flash on and off for 75 seconds and then remain on solid. In 3.
374 STARTING AND OPERATING warning limit in any of the four active road tires. The FUEL REQUIREMENTS vehicle may need to be driven for up to 20 minutes above 2.7L Engine 15 mph (25 km/h) in order for the TPMS to receive this The 2.7L engine is designed to meet all information. emissions regulations and provide excelGeneral Information lent fuel economy and performance when This device complies with Part 15 of the FCC rules and using high-quality unleaded “regular” RSS 210 of Industry Canada.
STARTING AND OPERATING 375 premium gasoline is not recommended, as it will not Reformulated Gasoline provide any benefit over regular gasoline in these en- Many areas of the country require the use of cleaner burning gasoline referred to as “Reformulated Gasoline.” gines. Reformulated gasoline contains oxygenates and are speLight spark knock at low engine speeds is not harmful to cifically blended to reduce vehicle emissions and imyour engine. However, continued heavy spark knock at prove air quality.
376 STARTING AND OPERATING CAUTION! DO NOT use gasoline containing Methanol or E85 Ethanol. Use of these blends may result in starting and driveability problems and may damage critical fuel system components.
STARTING AND OPERATING MMT In Gasoline MMT is a manganese-containing metallic additive that is blended into some gasoline to increase octane. Gasoline blended with MMT provides no performance advantage beyond gasoline of the same octane number without MMT. Gasoline blended with MMT reduces spark plug life and reduces emissions system performance in some vehicles. The manufacturer recommends that gasoline without MMT be used in your vehicle.
378 STARTING AND OPERATING CAUTION! (Continued) • An out-of-tune engine or certain fuel or ignition malfunctions can cause the catalytic converter to overheat. If you notice a pungent burning odor or some light smoke, your engine may be out of tune or malfunctioning and may require immediate service. Contact your authorized dealer for service assistance. • The use of fuel additives, which are now being sold as octane enhancers, is not recommended.
STARTING AND OPERATING 379 WARNING! (Continued) • Guard against carbon monoxide with proper maintenance. Have the exhaust system inspected every time the vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side windows fully open. • Keep the trunk closed when driving your vehicle to prevent carbon monoxide and other poisonous exhaust gases from entering the vehicle.
380 STARTING AND OPERATING NOTE: When removing the fuel filler cap, lay the cap tether in the hook, located on the fuel filler cap door reinforcement. CAUTION! • Damage to the fuel system or emissions control system could result from using an improper fuel tank filler tube cap (gas cap). • A poorly fitting gas cap could let impurities into the fuel system. • A poorly fitting gas cap may cause the Malfunction Indicator Light (MIL) to turn on.
STARTING AND OPERATING WARNING! (Continued) • Never add fuel to the vehicle when the engine is running. • A fire may result if gasoline is pumped into a portable container that is inside of a vehicle. You could be burned. Always place gas containers on the ground while filling. NOTE: • Tighten the gas cap until you hear a “clicking” sound. This is an indication that the gas cap is tightened properly. The MIL in the instrument cluster may turn on if the gas cap is not secured properly.
382 STARTING AND OPERATING Do not exceed the specified Gross Vehicle Weight Rating Gross Vehicle Weight Rating (GVWR) The GVWR is the total allowable weight of your vehicle. (GVWR) or the Gross Axle Weight Rating (GAWR). This includes driver, passengers, and cargo. The total Vehicle Certification Label load must be limited so that you do not exceed the Your vehicle has a Vehicle Certification Label affixed to GVWR. the rear of the driver’s door.
STARTING AND OPERATING Overloading The load carrying components (axle, springs, tires, wheels, etc.) of your vehicle will provide satisfactory service as long as you do not exceed the GVWR and the front and rear GAWR. The best way to figure out the total weight of your vehicle is to weigh it when it is fully loaded and ready for operation. Weigh it on a commercial scale to ensure that it is not over the GVWR.
384 STARTING AND OPERATING TRAILER TOWING In this section, you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle. Before towing a trailer, carefully review this information to tow your load as efficiently and safely as possible. exceed the GVWR. Refer to “Vehicle Loading/Vehicle Certification Label” in “Starting and Operating” for further information.
STARTING AND OPERATING Gross Axle Weight Rating (GAWR) The GAWR is the maximum capacity of the front and rear axles. Distribute the load over the front and rear axles evenly. Make sure that you do not exceed either front or rear GAWR. Refer to “Vehicle Loading/Vehicle Certification Label” in “Starting and Operating” for further information. WARNING! It is important that you do not exceed the maximum front or rear GAWR. A dangerous driving condition can result if either rating is exceeded.
386 STARTING AND OPERATING Weight-Distributing Hitch A weight-distributing system works by applying leverage through spring (load) bars. They are typically used for heavier loads to distribute trailer tongue weight to the tow vehicle’s front axle and the trailer axle(s). When used in accordance with the manufacturer’s directions, it provides for a more level ride, offering more consistent steering and brake control thereby enhancing towing safety.
STARTING AND OPERATING The following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition. Refer to the “Trailer Towing Weights (Maximum Trailer Weight Ratings)” chart for the Maximum GTW towable for your given drivetrain. Trailer Hitch Classification Definitions Max.
388 STARTING AND OPERATING Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/Transmission Frontal Area Max. GTW (Gross Trailer Wt.) 1,000 lbs (454 kg) Max. Tongue Wt. (See Note) 100 lbs (45 kg) 2.7L & 3.5L Rear Wheel 22 sq ft (2.04 sq m) Drive (RWD) Automatic 3.5L All Wheel Drive 32 sq ft (2.97 sq m) 2,000 lbs (907 kg) 200 lbs (91 kg) (AWD) & 5.
STARTING AND OPERATING 389 • The weight of the driver and all passengers. NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options or dealer-installed options must be considered as part of the total load on your vehicle. Refer to the “Tire and Loading Information” placard for the maximum combined weight of occupants and cargo for your vehicle.
390 STARTING AND OPERATING CAUTION! (Continued) WARNING! (Continued) • During the first 500 miles (805 km) that a trailer is towed, do not drive over 50 mph (80 km/h) and do not make starts at full throttle. This helps the engine and other parts of the vehicle wear in at the heavier loads. • Make certain that the load is secured in the trailer and it will not shift during travel.
STARTING AND OPERATING 391 WARNING! (Continued) WARNING! (Continued) • Vehicles with trailers should not be parked on a grade. When parking, apply the parking brake on the tow vehicle. Put the tow vehicle automatic transmission in PARK. Always, block or ⴖchockⴖ the trailer wheels. • GCWR must not be exceeded. • Total weight must be distributed between the tow vehicle and the trailer such that the following four ratings are not exceeded: 1.
392 STARTING AND OPERATING − Check for signs of tire wear or visible tire damage − An electronically actuated trailer brake controller is before towing a trailer. Refer to “Tires – General required when towing a trailer with electronically Information” in “Starting and Operating” for informaactuated brakes. When towing a trailer equipped with tion on tread wear indicators and for the proper a hydraulic surge actuated brake system, an electronic inspection procedure. brake controller is not required.
STARTING AND OPERATING WARNING! • Do not connect trailer brakes to your vehicle’s hydraulic brake lines. It can overload your brake system and cause it to fail. You might not have brakes when you need them and could have an accident. • Towing any trailer will increase your stopping distance. When towing, you should allow for additional space between your vehicle and the vehicle in front of you. Failure to do so could result in an accident.
394 STARTING AND OPERATING Four-Pin Connector 1 — Female Pins 2 — Male Pin 3 — Ground 4 — Park 5 — Left Stop/Turn 6 — Right Stop/Turn Seven-Pin Connector 1 2 3 4 — — — — Battery Backup Lamps Right Stop/Turn Electric Brakes 5 — Ground 6 — Left Stop/Turn 7 — Running Lamps
STARTING AND OPERATING Towing Tips Before setting out on a trip, practice turning, stopping, and backing up the trailer in an area located away from heavy traffic. 395 If you REGULARLY tow a trailer for more than 45 minutes of continuous operation, then change the automatic transmission fluid and filter according to the interval specified for “police, taxi, fleet, or frequent trailer towing.” Refer to “Maintenance Schedule” for the proper maintenance intervals.
396 STARTING AND OPERATING AutoStick威/Electronic Range Select (ERS) – If Equipped − By using the AutoStick威/Electronic Range Select (ERS) mode and selecting a specific gear range, frequent shifting can be avoided. The highest gear range should be selected that allows for adequate performance. For example, choose “4” if the desired speed can be maintained. Choose “3” or “2” if needed to maintain the desired speed.
STARTING AND OPERATING 397 WARNING! CAUTION! If the driveshaft is removed, the vehicle can roll even if the transmission is in PARK, which could cause serious injury or death. Towing this vehicle in violation of the above requirements can cause severe transmission and/or transfer case damage. Such damage is not covered by the New Vehicle Limited Warranty. The parking brake must be firmly engaged and the wheels chocked during driveshaft removal and installation.
WHAT TO DO IN EMERGENCIES CONTENTS 䡵 Hazard Warning Flasher . . . . . . . . . . . . . . . . 400 䡵 Jump-Starting Procedures . . . . . . . . . . . . . . . . 413 䡵 If Your Engine Overheats . . . . . . . . . . . . . . . . 400 ▫ Preparations For Jump-Start . . . . . . . . . . . . . 413 䡵 Jacking And Tire Changing . . . . . . . . . . . . . . . 401 ▫ Jump-Starting Procedure . . . . . . . . . . . . . . . 415 ▫ Jack Location/Spare Tire Stowage . . . . . . . . 402 䡵 Freeing A Stuck Vehicle . . . . . . . . . .
400 WHAT TO DO IN EMERGENCIES NOTE: With extended use the Hazard Warning flasher HAZARD WARNING FLASHER The Hazard Warning flasher switch is located in the may wear down your battery. center of the instrument panel between the center air IF YOUR ENGINE OVERHEATS outlets. In any of the following situations, you can reduce the Press the switch to turn on the Hazard Warning potential for overheating by taking the appropriate acflasher. When the switch is activated, all directional tion.
WHAT TO DO IN EMERGENCIES • You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high. This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system. CAUTION! Driving with a hot cooling system could damage your vehicle. If the temperature gauge reads “H,” pull over and stop the vehicle.
402 WHAT TO DO IN EMERGENCIES WARNING! (Continued) • Getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never get any part of your body under a vehicle that is on a jack. Never start or run the engine while the vehicle is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift. • The jack is designed to use as a tool for changing tires only.
WHAT TO DO IN EMERGENCIES 403 3. Remove the fastener securing the spare tire. Jack Fastener Spare Tire Fastener 4. Remove the spare tire. 5. Remove the fastener securing the jack. WARNING! A loose tire or jack thrown forward in a collision or hard stop could endanger the occupants of the vehicle. Always stow the jack parts and the spare tire in the places provided.
404 WHAT TO DO IN EMERGENCIES Preparations for Jacking 1. Park the vehicle on a firm, level surface as far from the edge of the roadway as possible. Avoid icy or slippery areas. 6. Block the front and rear of the wheel diagonally opposite of the jacking position. For example, if changing the right front tire, block the left rear wheel. WARNING! Do not attempt to change a tire on the side of the vehicle close to moving traffic.
WHAT TO DO IN EMERGENCIES 405 WARNING! (Continued) WARNING! (Continued) • Always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle. • Block the wheel diagonally opposite the wheel to be raised. • Set the parking brake firmly and set an automatic transmission in PARK; a manual transmission in REVERSE. • Never start or run the engine with the vehicle on a jack. • Do not let anyone sit in the vehicle when it is on a jack.
406 WHAT TO DO IN EMERGENCIES 2. If equipped with steel wheels, do not remove the wheel cover at this time. If equipped with aluminum wheels where the center cap covers the lug nuts, use the lug wrench to pry the center cap off carefully before raising the vehicle. Center Cap Removal WARNING! To avoid possible personal injury, handle the wheel covers with care to avoid contact with the metal edges and retention teeth.
WHAT TO DO IN EMERGENCIES 407 3. Before raising the vehicle, use the lug wrench to 4. Place the jack underneath the lift area that is closest to loosen, but not remove, the lug nuts on the wheel with the flat tire. Turn the jack screw clockwise to firmly the flat tire. Turn the lug nuts counterclockwise one turn engage the jack saddle with the lift area of the sill flange. while the wheel is still on the ground.
408 WHAT TO DO IN EMERGENCIES Jack Engagement Locations
WHAT TO DO IN EMERGENCIES 409 5. Raise the vehicle just enough to remove the flat tire 8. Install the lug nuts with the cone shaped end of the lug and install the spare tire. nut toward the wheel. Lightly tighten the lug nuts. To avoid the risk of forcing the vehicle off the jack, do not WARNING! tighten the lug nuts fully until the vehicle is lowered to the ground. Raising the vehicle higher than necessary can make 9. Lower the vehicle to the ground by turning the jack the vehicle less stable.
410 WHAT TO DO IN EMERGENCIES WARNING! WARNING! A loose tire or jack thrown forward in a collision or hard stop could endanger the occupants of the vehicle. Always stow the jack parts and the spare tire in the places provided. The limited-use spare tires are for emergency use only. Installation of this limited-use spare tire affects vehicle handling. With this tire, do not drive more than 60 mph (100 km/h).
WHAT TO DO IN EMERGENCIES 411 1. Mount the road tire on the axle. For vehicles equipped with wheel covers, perform Steps 2 and 3. For vehicles equipped with center caps, proceed to Step 4. 2. Install two lug nuts on the mounting studs, which are on each side of the stud that is in alignment with the valve stem. Install the lug nuts with the cone shaped end of the nut toward the wheel. Lightly tighten the lug nuts.
412 WHAT TO DO IN EMERGENCIES 3. Align the valve notch in the wheel cover with the 7. For vehicles equipped with center caps, install the valve stem on the wheel. Install the cover by hand, center cap by hand. Do not use a hammer or excessive snapping the cover over the two lug nuts. Do not use a force to install the center cap. hammer or excessive force to install the cover. 8. Stow the jack, tools, and spare tire. Make sure the base 4.
WHAT TO DO IN EMERGENCIES 413 JUMP-STARTING PROCEDURES WARNING! If your vehicle has a discharged battery it can be jumpstarted using a set of jumper cables and a battery in Do not attempt jump-starting if the battery is frozen. another vehicle or by using a portable battery booster It could rupture or explode and cause personal injury. pack. Jump-starting can be dangerous if done improperly so please follow the procedures in this section carefully.
414 WHAT TO DO IN EMERGENCIES Remote Battery Posts WARNING! 1 — Remote Negative (-) Post 2 — Remote Positive (+) Post • Take care to avoid the radiator cooling fan whenever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan blades. • Remove any metal jewelry such as watch bands or bracelets that might make an inadvertent electrical contact. You could be seriously injured.
WHAT TO DO IN EMERGENCIES 2. Turn off the heater, radio, and all unnecessary electrical accessories. 3. If using another vehicle to jump-start the battery, park the vehicle within the jumper cables reach, set the parking brake and make sure the ignition is OFF. 415 CAUTION! Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle. WARNING! 1.
416 WHAT TO DO IN EMERGENCIES WARNING! 8. Disconnect the opposite end of the positive (+) jumper cable from the positive (+) post of the booster battery. Do not connect the cable to the negative post (-) of the discharged battery. The resulting electrical spark could cause the battery to explode and could result in personal injury. 9. Disconnect the positive (+) end of the jumper cable from the remote positive (+) post of the discharged vehicle.
WHAT TO DO IN EMERGENCIES FREEING A STUCK VEHICLE If your vehicle becomes stuck in mud, sand, or snow, it can often be moved by a rocking motion. Turn your steering wheel right and left to clear the area around the front wheels. Then shift back and forth between REVERSE and DRIVE. Using minimal accelerator pedal pressure to maintain the rocking motion, without spinning the wheels, is most effective.
418 WHAT TO DO IN EMERGENCIES WARNING! Fast spinning tires can be dangerous. Forces generated by excessive wheel speeds may cause damage, or even failure, of the axle and tires. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 30 mph (48 km/h) or for longer than 30 seconds continuously without stopping when you are stuck and do not let anyone near a spinning wheel, no matter what the speed.
WHAT TO DO IN EMERGENCIES Vehicles equipped with AWD can be towed with the transmission in NEUTRAL and the rear wheels OFF the ground (or the rear driveshaft removed) with no limitation on speed or distance. CAUTION! • Do not attempt to tow this vehicle from the front with sling-type towing equipment. Damage to the front fascia will result.
MAINTAINING YOUR VEHICLE CONTENTS 䡵 Engine Compartment — 2.7L . . . . . . . . . . . . . 423 䡵 Maintenance Procedures . . . . . . . . . . . . . . . . . 429 䡵 Engine Compartment — 3.5L . . . . . . . . . . . . . 424 ▫ Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . 430 䡵 Engine Compartment — 5.7L . . . . . . . . . . . . . 425 ▫ Engine Oil Filter . . . . . . . . . . . . . . . . . . . . . 433 䡵 Onboard Diagnostic System — OBD II . . . . . . 426 ▫ Engine Air Cleaner Filter . . . . . . . . . . .
422 MAINTAINING YOUR VEHICLE ▫ Adding Washer Fluid . . . . . . . . . . . . . . . . . 440 䡵 Bulb Replacement . . . . . . . . . . . . . . . . . . . . . 470 ▫ Exhaust System . . . . . . . . . . . . . . . . . . . . . 441 ▫ Low Beam Headlamp, High Beam Headlamp, Park/Turn Lamp, Inner Park Lamp, And Outer Park Lamp – 300 Models . . 470 ▫ Cooling System . . . . . . . . . . . . . . . . . . . . . 444 ▫ Brake System . . . . . . . . . . . . . . . . . . . . . . . 449 ▫ Automatic Transmission . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 423 ENGINE COMPARTMENT — 2.
424 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT — 3.
MAINTAINING YOUR VEHICLE 425 ENGINE COMPARTMENT — 5.
426 MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
MAINTAINING YOUR VEHICLE 427 TRIP ODOMETER button to turn off the message. If the serviced, recently had a dead battery or a battery replaceproblem continues, the message will appear the next time ment. If the OBD II system should be determined not ready for the I/M test, your vehicle may fail the test. the vehicle is started. A loose, improperly installed, or damaged fuel filler cap Your vehicle has a simple ignition key-actuated test, which you can use prior to going to the test station.
428 MAINTAINING YOUR VEHICLE a. The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine. This means that your vehicle’s OBD II system is not ready and you should not proceed to the I/M station. vehicle operation you should have your vehicle serviced before going to the I/M station. The I/M station can fail your vehicle because the MIL is on with the engine running.
MAINTAINING YOUR VEHICLE 429 NOTE: Intentional tampering with emissions control Besides those maintenance items specified in the fixed systems may void your warranty and could result in civil maintenance schedule, there are other components which penalties being assessed against you. may require servicing or replacement in the future. WARNING! CAUTION! You can be badly injured working on or around a motor vehicle. Only do service work for which you have the knowledge and the proper equipment.
430 MAINTAINING YOUR VEHICLE CAUTION! (Continued) • Your vehicle has been built with improved fluids that protect the performance and durability of your vehicle and also allow extended maintenance intervals. Do not use chemical flushes in these components as the chemicals can damage your engine, transmission, power steering or air conditioning. Such damage is not covered by the New Vehicle Limited Warranty.
MAINTAINING YOUR VEHICLE Checking the oil while the vehicle is on level ground will improve the accuracy of the oil level readings. Maintain the oil level in the “SAFE” range. Adding 1.0 qt (1.0 L) of oil when the reading is at the bottom of the “SAFE” range will result in an oil level at the top of the “SAFE” range on these engines. CAUTION! 431 NOTE: Under no circumstances should oil change intervals exceed 6,000 miles (10 000 km) or six months, whichever occurs first.
432 MAINTAINING YOUR VEHICLE CAUTION! Do not use chemical flushes in your engine oil as the chemicals can damage your engine. Such damage is not covered by the New Vehicle Limited Warranty. operation of the Multi-Displacement System (MDS). Refer to “Multi-Displacement System” in “Starting and Operating” for further information. Lubricants which do not have both, the engine oil certification mark and the correct SAE viscosity grade number should not be used. Engine Oil Viscosity (SAE Grade) – 2.7L and 5.
MAINTAINING YOUR VEHICLE Synthetic Engine Oils You may use synthetic engine oils provided the recommended oil quality requirements are met, and the recommended maintenance intervals for oil and filter changes are followed. 433 Engine Oil Filter The engine oil filter should be replaced with a new filter at every engine oil change. Engine Oil Filter Selection This manufacturer’s engines have a full-flow type oil Materials Added to Engine Oil filter. Use a filter of this type for replacement.
434 MAINTAINING YOUR VEHICLE WARNING! The air induction system (air cleaner, hoses, etc.) can provide a measure of protection in the case of engine backfire. Do not remove the air induction system (air cleaner, hoses, etc.) unless such removal is necessary for repair or maintenance. Make sure that no one is near the engine compartment before starting the vehicle with the air induction system (air cleaner, hoses, etc.) removed. Failure to do so can result in serious personal injury.
MAINTAINING YOUR VEHICLE 435 WARNING! Battery Location • Battery fluid is a corrosive acid solution and can burn or even blind you. Do not allow battery fluid to contact your eyes, skin, or clothing. Do not lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area immediately with large amounts of water. • Battery gas is flammable and explosive. Keep flame or sparks away from the battery.
436 MAINTAINING YOUR VEHICLE WARNING! (Continued) • The battery in this vehicle has a vent hose that should not be disconnected and should only be replaced with a battery of the same type (vented). CAUTION! • It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked positive (+) and negative (-) and are identified on the battery case.
MAINTAINING YOUR VEHICLE WARNING! • Use only refrigerants and compressor lubricants approved by the manufacturer for your air conditioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs. Refer to the Warranty Information Book, located on the DVD, for further warranty information. • The air conditioning system contains refrigerant under high pressure.
438 MAINTAINING YOUR VEHICLE 1. Remove the access door in the cowl screen by pressing 2. Slide the lid on the filter adapter forward and down the retaining clips. and remove the used filter.
MAINTAINING YOUR VEHICLE 439 3. Install the new filter with arrows pointing in the Body Lubrication direction of airflow, which is toward the rear of the Locks and all body pivot points, including such items as vehicle (text and arrows on the filter will indicate this).
440 MAINTAINING YOUR VEHICLE The external lock cylinders should be lubricated twice a year, preferably in the Fall and Spring. Apply a small amount of a high quality lubricant, such as MOPAR威 Lock Cylinder Lubricant or equivalent, directly into the lock cylinder. NOTE: Life expectancy of wiper blades varies depending on geographical area and frequency of use. Poor performance of blades may be present with chattering, marks, water lines or wet spots.
MAINTAINING YOUR VEHICLE To prevent freeze-up of your windshield washer system in cold weather, select a solution or mixture that meets or exceeds the temperature range of your climate. This rating information can be found on most washer fluid containers. The fluid reservoir will hold nearly 1 gal (4 L) of washer fluid when the message “Low Washer Fluid” appears in the Electronic Vehicle Information Center (EVIC) (if equipped). WARNING! Commercially available windshield washer solvents are flammable.
442 MAINTAINING YOUR VEHICLE WARNING! CAUTION! • Exhaust gases can injure or kill. They contain carbon monoxide (CO), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing CO, refer to “Safety Tips/Exhaust Gas” in “Things To Know Before Starting Your Vehicle” for further information. • A hot exhaust system can start a fire if you park over materials that can burn.
MAINTAINING YOUR VEHICLE 443 Under normal operating conditions, the catalytic con- To minimize the possibility of catalytic converter damverter will not require maintenance. However, it is im- age: portant to keep the engine properly tuned to assure • Do not shut off the engine or interrupt the ignition, proper catalyst operation and prevent possible catalyst when the transmission is in gear and the vehicle is in damage. motion.
444 MAINTAINING YOUR VEHICLE Cooling System WARNING! • When working near the radiator cooling fan, disconnect the fan motor lead or turn the ignition switch to the LOCK position (OFF position for Keyless Go™). The fan is temperature controlled and can start at any time the ignition switch is in the ON position (RUN position for Keyless Go™). • You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.
MAINTAINING YOUR VEHICLE Cooling System – Drain, Flush, and Refill If the engine coolant (antifreeze) is dirty or contains a considerable amount of sediment, clean and flush with a reliable cooling system cleaner. Follow with a thorough rinsing to remove all deposits and chemicals. Properly dispose of the old engine coolant (antifreeze) solution. Refer to “Maintenance Schedule” for the proper maintenance intervals. Selection of Coolant Use only the manufacturer’s recommended engine coolant (antifreeze).
446 MAINTAINING YOUR VEHICLE CAUTION! (Continued) • This vehicle has not been designed for use with propylene glycol-based engine coolant (antifreeze). Use of propylene glycol-based engine coolant (antifreeze) is not recommended. • The manufacturer recommends using MOPAR威 Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) or equivalent. • Mix a minimum solution of 50% HOAT engine coolant (antifreeze) and distilled water.
MAINTAINING YOUR VEHICLE NOTE: Mixing engine coolant (antifreeze) types will decrease the life of the engine coolant (antifreeze) and will require more frequent engine coolant (antifreeze) changes. Cooling System Pressure Cap The cap must be fully tightened to prevent loss of engine coolant (antifreeze), and to ensure that engine coolant (antifreeze) will return to the radiator from the coolant recovery bottle.
448 MAINTAINING YOUR VEHICLE Disposal of Used Coolant Used ethylene glycol-based engine coolant (antifreeze) is a regulated substance requiring proper disposal. Check with your local authorities to determine the disposal rules for your community. To prevent ingestion by animals or children, do not store ethylene glycol-based engine coolant (antifreeze) in open containers or allow it to remain in puddles on the ground. If ingested by a child or pet, seek emergency assistance immediately.
MAINTAINING YOUR VEHICLE 449 If an examination of your engine compartment shows no • Make sure that the radiator and coolant recovery evidence of radiator or hose leaks, the vehicle may be bottle overflow hoses are not kinked or obstructed. safely driven. The vapor will soon dissipate. • Keep the front of the radiator clean. If your vehicle is equipped with air conditioning, keep the front of the • Do not overfill the coolant recovery bottle. condenser clean.
450 MAINTAINING YOUR VEHICLE WARNING! Riding the brakes can lead to brake failure and possibly an accident. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage. You would not have your full braking capacity in an emergency. Clean the top of the master cylinder area before removing the cap. Add fluid to bring the level up to the “MAX” mark on the side of the master cylinder reservoir.
MAINTAINING YOUR VEHICLE 451 WARNING! WARNING! (Continued) • Use only manufacturer’s recommended brake fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for further information. Using the wrong type of brake fluid can severely damage your brake system and/or impair its performance. The proper type of brake fluid for your vehicle is also labeled on the original factory installed hydraulic master cylinder reservoir.
452 MAINTAINING YOUR VEHICLE WARNING! (Continued) CAUTION! • Do not allow petroleum based fluid to contaminate the brake fluid. Brake seal components could be damaged, causing partial or complete brake failure. This could result in an accident. • Using a transmission fluid other than the manufacturer’s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder.
MAINTAINING YOUR VEHICLE 453 Fluid and Filter Changes Special Additives Refer to “Maintenance Schedule” for the proper mainte- Automatic Transmission Fluid (ATF) is an engineered nance intervals. product and its performance may be impaired by supplemental additives. Therefore, do not add any fluid addiIf the transmission is disassembled for any reason, the tives to the transmission. The only exception to this fluid and filter should be changed.
454 MAINTAINING YOUR VEHICLE All Wheel Drive (AWD) – If Equipped The all wheel drive system consists of a transfer case and front differential. The exterior surface of these components should be inspected for evidence of fluid leaks. Confirmed leaks should be repaired as soon as possible. Rear Axle For normal service, periodic fluid level checks are not required. When the vehicle is serviced for other reasons the exterior surfaces of the axle assembly should be inspected.
MAINTAINING YOUR VEHICLE Appearance Care and Protection from Corrosion The most common causes are: Protection of Body and Paint from Corrosion Vehicle body care requirements vary according to geographic locations and usage. Chemicals that make roads passable in snow and ice, and chemicals that are sprayed on trees and road surfaces during other seasons, are highly corrosive to the metal in your vehicle.
456 MAINTAINING YOUR VEHICLE • Use a high quality cleaner wax, such as MOPAR威 Special Care Cleaner Wax or equivalent to remove road film, stains • If you drive on salted or dusty roads or if you drive and to protect your paint finish. Take care never to near the ocean, hose off the undercarriage at least once scratch the paint. a month.
MAINTAINING YOUR VEHICLE 457 • If you carry special cargo such as chemicals, fertilizers, Avoid automatic car washes that use acidic solutions or de-icer salt, etc., be sure that such materials are well harsh brushes that may damage the wheels’ protective finish. packaged and sealed. • If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel.
458 MAINTAINING YOUR VEHICLE • Do not use any harsh solvents or any other form of and appropriate products such as MOPAR威 Total Clean or equivalent. Care should be taken to avoid soaking protectants on Stain Repel products. your leather upholstery with any liquid. Please do not Interior Care use polishes, oils, cleaning fluids, solvents, detergents, or Use MOPAR威 Fabric Cleaner or equivalent to clean fabric ammonia-based cleaners to clean your leather upholstery.
MAINTAINING YOUR VEHICLE To minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. To remove road dirt, wash with a mild soap solution followed by rinsing. 459 Cleaning Plastic Instrument Cluster Lenses The lenses in front of the instruments in this vehicle are molded in clear plastic. When cleaning the lenses, care must be taken to avoid scratching the plastic. Do not use abrasive cleaning components, solvents, steel 1.
460 MAINTAINING YOUR VEHICLE Replace the belts if they appear frayed or worn or if the buckles do not work properly. Cleaning the Center Console Cupholders Clean with a damp cloth or towel using a mild detergent with the cupholder in the center console. NOTE: The cupholder cannot be removed. FUSES Integrated Power Module The Integrated Power Module (IPM) is located in the engine compartment. This module contains fuses and relays.
MAINTAINING YOUR VEHICLE CAUTION! • When installing the integrated power module cover, it is important to ensure the cover is properly positioned and fully latched. Failure to do so may allow water to get into the integrated power module and possibly result in an electrical system failure. • When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating. The use of a fuse with a rating other than indicated may result in a dangerous electrical system overload.
462 MAINTAINING YOUR VEHICLE Cavity 8 9 10 11 12 13 Cartridge Fuse — MiniFuse Description 30 Amp Starter Green — — — 30 Amp — Windshield Wiper Pink 30 Amp — Anti-Lock Brake System Pink (ABS) Valves – If Equipped 40 Amp — Radiator Fan Green 50 Amp — Anti-Lock Brake System Red (ABS) Pump Motor – If Equipped Cavity 14 15 16 17 18 19 20 21 22 Cartridge Fuse — 50 Amp Red — — — — — — — MiniFuse Description — — — Radiator Fan — — — — — — — — — — — — — —
MAINTAINING YOUR VEHICLE 463 Rear Power Distribution Center There is also a power distribution center located in the trunk under the spare tire access panel. This center contains fuses and relays.
464 MAINTAINING YOUR VEHICLE CAUTION! • When installing the power distribution center cover, it is important to ensure the cover is properly positioned and fully latched. Failure to do so may allow water to get into the power distribution center and possibly result in an electrical system failure. • When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating. The use of a fuse with a rating other than indicated may result in a dangerous electrical system overload.
MAINTAINING YOUR VEHICLE Cavity 6 Cartridge Fuse 30 Amp Pink — 7 — 8 — 5 9 — 10 11 * 12 * — — — MiniFuse — Description Heated Seats – If Equipped 20 Amp Fuel Pump Yellow 15 Amp Rear Heated Seats – If Blue Equipped 15 Amp Diagnostic Link ConnecBlue tor (DLC)/Wireless Control Module (WCM)/ Wireless Ignition Node (WIN) 20 Amp Power Outlet Yellow — — — — — — Cavity 13 * 14 Cartridge Fuse — — 15 — 16 17 — — 18 — 19 — 20 21 — — MiniFuse 465 Description — — 10 Amp AC Heater Control/
466 MAINTAINING YOUR VEHICLE Cavity 22 23 24 25 26 27 Cartridge Fuse — — — — — — 28 — MiniFuse Description Cavity — — — — — 10 Amp Red 10 Amp Red — — — — — Occupant Restraint Controller (ORC) Ignition Run, AC Heater Control/Headlights/ Park Assist – If Equipped/Tire Pressure Monitoring – If Equipped/Occupant Restraint Controller (ORC) 29 Cartridge Fuse — 30 — 31 32 33 34 — — — — MiniFuse 5 Amp Orange Description Adaptive Cruise Control (ACC) – If Equipped/ Cluster/Electronic Stability Pr
MAINTAINING YOUR VEHICLE Cavity 35 Cartridge Fuse — 36 — 37 — 38 — MiniFuse 5 Amp Orange Description Antenna Module – If Equipped/Power Mirrors/Rain Sensor – If Equipped 25 Amp Hands-Free Phone – If Natural Equipped/Video Monitor – If Equipped/Radio 15 Amp Transmission Blue 10 Amp Analog Clock/Cargo Red Light/Satellite Receiver (SDARS) Video – If Equipped/Vehicle Information Module – If Equipped Cavity 39 40 41 42 43 44 Cartridge Fuse — MiniFuse 467 Description 10 Amp Red 5 Amp Orange H
468 MAINTAINING YOUR VEHICLE * Cavities 11, 12, and 13 contain self-resetting fuses (circuit breakers) that are only serviceable by an authorized dealer. The cluster, the driver seat switch (if equipped), and the memory module (if equipped) are fused by the 25 Amp circuit breaker in Cavity 11. The passenger seat switch (if equipped) is fused by the 25 Amp circuit breaker in Cavity 12.
MAINTAINING YOUR VEHICLE 469 NOTE: For lighted switches, see your authorized dealer Exterior (300C Models) Bulb Number for replacement instructions. Low Beam Headlamp (Standard Halogen) . . . . 9006XS All of the interior bulbs are glass wedge base or glass Low Beam Headlamp – High Intensity Discharge cartridge types. Aluminum base bulbs are not approved (HID) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D1S (Serviced at Authorized Dealer) and should not be used for replacement.
470 MAINTAINING YOUR VEHICLE BULB REPLACEMENT Low Beam Headlamp, High Beam Headlamp, Park/Turn Lamp, Inner Park Lamp, and Outer Park Lamp – 300 Models 1. Open the hood. NOTE: Removal of the air cleaner filter housing may be necessary prior to replacing bulbs in the headlamp assembly on the driver side of the vehicle. 2. Twist the appropriate bulb and socket assembly counterclockwise, and then pull it out of the headlamp assembly. 3.
MAINTAINING YOUR VEHICLE 3 — Park/Turn Lamp Bulb 4 — Inner Park Lamp Bulb 5 — Outer Park Lamp Bulb 471 7
472 MAINTAINING YOUR VEHICLE CAUTION! WARNING! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with an oily surface, clean the bulb with rubbing alcohol. A transient high tension occurs at the bulb sockets of HID headlamps when the headlamp switch is turned ON. It may cause serious electrical shock or electrocution if not serviced properly. See your authorized dealer for service.
MAINTAINING YOUR VEHICLE 473 2. Remove two fasteners from the back of the tail lamp 5. Push the electrical connector locking tab to the side. assembly. 6. Disconnect the electrical connector. 7 3. Pull back the trunk liner. 4. Remove the remaining fastener from the back of the tail lamp assembly.
474 MAINTAINING YOUR VEHICLE 7. Pull the tail lamp assembly clear from the vehicle to access the bulbs. 8. Turn the appropriate bulb and socket assembly counterclockwise to remove it from the tail lamp assembly.
MAINTAINING YOUR VEHICLE 475 9. Disconnect the bulb from the socket assembly and install the replacement bulb. 10. Reinstall the bulb and socket assembly into the tail lamp assembly, and then turn it clockwise. 11. Reinstall the tail lamp assembly, fasteners, electrical connector, and trunk liner. 12. Close the trunk.
476 MAINTAINING YOUR VEHICLE Tail/Stop, Tail, Turn Signal Lamp, and Backup Lamp — 300C Models 4. Remove the remaining fastener from the back of the tail lamp assembly. 1. Open the trunk. 5. Push the electrical connector locking tab to the side. 2. Remove two fasteners from the back of the tail lamp 6. Disconnect the electrical connector. assembly. 3. Pull back the trunk liner.
MAINTAINING YOUR VEHICLE 477 7. Pull the tail lamp assembly clear from the vehicle to access the bulbs. Turn bulb sockets counterclockwise to remove. 8. Turn the appropriate bulb and socket assembly counterclockwise to remove it from the tail lamp assembly.
478 MAINTAINING YOUR VEHICLE 3 — Turn Signal Lamp Bulb 4 — Backup Lamp Bulb 9. Disconnect the bulb from the socket assembly and install the replacement bulb. 10. Reinstall the bulb and socket assembly into the tail lamp assembly, and then turn it clockwise.
MAINTAINING YOUR VEHICLE 479 11. Reinstall the tail lamp assembly, fasteners, electrical connector, and trunk liner. 12. Close the trunk. License Lamp 1. Remove the screws securing the lamp to the rear fascia. 2. Remove the bulb and socket assembly. 3. Disconnect the bulb from the socket assembly and install the replacement bulb. 1 — License Lamp Bulb 2 — Socket 4. Reinstall the bulb and socket assembly. 5. Reattach the lamp to the rear fascia, and then install the screws.
480 MAINTAINING YOUR VEHICLE FLUID CAPACITIES U.S. Fuel (Approximate) 2.7 Liter Engine 3.5 Liter Engine without All Wheel Drive 3.5 Liter Engine with All Wheel Drive 5.7 Liter Engine Engine Oil with Filter 2.7 Liter Engine (SAE 5W-20, API Certified) 3.5 Liter Engine (SAE 10W-30, API Certified) 5.7 Liter Engine (SAE 5W-20, API Certified) Cooling System * 2.
MAINTAINING YOUR VEHICLE 3.5 Liter Engine without All Wheel Drive (MOPAR威 Antifreeze/ Coolant 5 Year/100,000 Mile Formula or equivalent) 3.5 Liter Engine with All Wheel Drive (MOPAR威 Antifreeze/Coolant 5 Year/100,000 Mile Formula or equivalent) 5.7 Liter Engine without Severe Duty II Cooling System (MOPAR威 Antifreeze/Coolant 5 Year/100,000 Mile Formula or equivalent) 5.
482 MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS, AND GENUINE PARTS Engine Component Engine Coolant Engine Oil – 2.7L Engine Engine Oil – 3.5L Engine Engine Oil – 5.7L Engine Engine Oil Filter Spark Plugs – 2.7L Engine Spark Plugs – 3.5L Engine Spark Plugs – 5.7L Engine Fluid, Lubricant, or Genuine Part MOPAR威 Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) or equivalent.
MAINTAINING YOUR VEHICLE Component Fuel Selection – 2.7L Engine Fuel Selection – 3.5L and 5.7L Engines 483 Fluid, Lubricant, or Genuine Part 87 Octane 87 Octane Acceptable — 89 Octane Recommended Chassis Component Automatic Transmission Brake Master Cylinder Power Steering Reservoir Front Axle Rear Axle Transfer Case Fluid, Lubricant, or Genuine Part MOPAR威 ATF+4威 Automatic Transmission Fluid or equivalent licensed ATF+4威 product. MOPAR威 DOT 3 and SAE J1703 should be used or equivalent.
M A I N T E N A N C ▫ Required Maintenance Intervals . . . . . . . . . . 488 E MAINTENANCE SCHEDULES CONTENTS 䡵 Emissions Control System Maintenance . . . . . . 486 䡵 Maintenance Schedule . . . . . . . . . . . . . . . . . .
M A I N T E N A N C E 486 MAINTENANCE SCHEDULES EMISSIONS CONTROL SYSTEM MAINTENANCE The Scheduled Maintenance services listed in bold type must be done at the times or mileages specified to ensure the continued proper functioning of the emissions control system. These and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
MAINTENANCE SCHEDULES NOTE: • The oil change indicator message will not monitor the time since the last oil change. Change your vehicle’s oil if it has been six months since your last oil change, even if the oil change indicator message is NOT illuminated. • Change your engine oil more often if you drive your vehicle off-road for an extended period of time. 487 M A I N T E N A At Each Stop for Fuel N C • Check the engine oil level.
M A I N T E N A N C E 488 MAINTENANCE SCHEDULES • Check the fluid levels of the coolant reservoir, brake master cylinder, and power steering, add as needed. CAUTION! • Check all lights and other electrical items for correct operation. Failure to perform the required maintenance items may result in damage to the vehicle. At Each Oil Change • Change the engine oil filter. S • Inspect the brake hoses and lines.
MAINTENANCE SCHEDULES 6,000 Miles (10,000 km) or 6 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. Odometer Reading Repair Order # Signature Authorized Chrysler Dealer Date Dealer Code 489 M 12,000 Miles (20,000 km) or 12 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions.
M 490 MAINTENANCE SCHEDULES A I 18,000 Miles (30,000 km) or N T 18 Months Maintenance E Service Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate tires. C ❏ Inspect the rear axle fluid. Inspect the E S C H E D U L E S 8 24,000 Miles (40,000 km) or 24 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions.
MAINTENANCE SCHEDULES 30,000 Miles (50,000 km) or 30 Months Maintenance Service Schedule 36,000 Miles (60,000 km) or 36 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ Replace the engine air cleaner filter. ❏ Replace the spark plugs (5.7L Engine). ❏ Inspect the transfer case fluid — All Wheel Drive (AWD). ❏ Adjust parking brake on vehicles equipped with four-wheel disc brakes.
M 492 MAINTENANCE SCHEDULES A I 42,000 Miles (70,000 km) or N T 42 Months Maintenance E Service Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate tires. C E 48,000 Miles (80,000 km) or 48 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary.
MAINTENANCE SCHEDULES A I N T E N A N C E 54,000 Miles (90,000 km) or 54 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ Inspect the rear axle fluid. Inspect the front axle fluid — All Wheel Drive (AWD).
M 494 MAINTENANCE SCHEDULES A I 60,000 Miles (100,000 km) or 60 Months Maintenance Service Schedule N ❏ Change the engine oil and engine oil filter. T E ❏ Rotate tires. N ❏ Replace the engine air cleaner filter. A ❏ Replace the spark plugs (5.7L Engine). N ❏ Replace the air conditioning filter (if equipped) C ❏ Inspect the brake linings; replace if necessary. E ❏ Adjust parking brake on vehicles equipped with four-wheel disc brakes.
MAINTENANCE SCHEDULES 66,000 Miles (110,000 km) or 66 Months Maintenance Service Schedule 72,000 Miles (120,000 km) or 72 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. ❏ Replace the air conditioning filter (if equipped) ❏ Inspect the rear axle fluid. Inspect the front axle fluid — All Wheel Drive (AWD).
M 496 MAINTENANCE SCHEDULES A I 78,000 Miles (130,000 km) or N T 78 Months Maintenance E Service Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate tires. C E 84,000 Miles (140,000 km) or 84 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary.
MAINTENANCE SCHEDULES 90,000 Miles (150,000 km) or 90 Months Maintenance Service Schedule ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ Change the engine oil and engine oil filter. Rotate tires. Replace the engine air cleaner filter. Replace the spark plugs (5.7L Engine). Inspect and replace PCV valve if necessary. † Inspect the rear axle fluid. Inspect the front axle fluid — All Wheel Drive (AWD). Inspect the transfer case fluid — All Wheel Drive (AWD). Adjust parking brake on vehicles equipped with four-wheel disc brakes.
M 498 MAINTENANCE SCHEDULES A I 96,000 Miles (160,000 km) or 96 Months Maintenance Service N T Schedule E ❏ Change the engine oil and engine oil filter. N ❏ Rotate tires. A ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the N engine air cleaner filter; replace if necessary. C ❏ Replace the air conditioning filter (if equipped) E ❏ Inspect the brake linings; replace if necessary. S C H E D U L E S 8 ❏ Inspect the CV joints. ❏ Inspect exhaust system.
MAINTENANCE SCHEDULES 108,000 Miles (180,000 km) or 108 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. ❏ Replace the air conditioning filter (if equipped) ❏ Inspect the rear axle fluid. Inspect the front axle fluid — All Wheel Drive (AWD). ❏ Inspect the brake linings; replace if necessary.
M 500 MAINTENANCE SCHEDULES A I 120,000 Miles (200,000 km) or 120 Months Maintenance Service Schedule N ❏ Change the engine oil and engine oil filter. T E ❏ Rotate tires. N ❏ Replace the engine air cleaner filter. A ❏ Replace the air conditioning filter (if equipped) N ❏ Replace the spark plugs (5.7L Engine). C ❏ Inspect the brake linings; replace if necessary. E ❏ Adjust parking brake on vehicles equipped with four-wheel disc brakes. S C H E D U L E S 8 ❏ Inspect the CV joints. ❏ Inspect exhaust system.
MAINTENANCE SCHEDULES 126,000 Miles (210,000 km) or 126 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ Inspect the rear axle fluid. Inspect the front axle fluid — All Wheel Drive (AWD). Odometer Reading Repair Order # Signature Authorized Chrysler Dealer Date Dealer Code 501 M 132,000 Miles (220,000 km) or 132 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires.
M 502 MAINTENANCE SCHEDULES A I 138,000 Miles (230,000 km) or N T 138 Months Maintenance E Service Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate tires. C E S C H E D U L E S 8 Odometer Reading Repair Order # Signature Authorized Chrysler Dealer Date Dealer Code 144,000 Miles (240,000 km) or 144 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions.
MAINTENANCE SCHEDULES 503 M A 150,000 Miles (250,000 km) or 150 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ Replace the engine air cleaner filter. ❏ Replace the spark plugs (5.7L Engines). ❏ Inspect the transfer case fluid — All Wheel Drive (AWD). ❏ Adjust parking brake on vehicles equipped with four-wheel disc brakes.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS 䡵 Suggestions For Obtaining Service For Your Vehicle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 507 ▫ Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) . . . . . . . . . . . . 509 ▫ Prepare For The Appointment . . . . . . . . . . . 507 ▫ Service Contract . . . . . . . . . . . . . . . . . . . . . 509 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . 507 䡵 Warranty Information . . . . . . . . . . . . . . . . . .
506 IF YOU NEED CONSUMER ASSISTANCE 䡵 Publication Order Forms . . . . . . . . . . . . . . . . 511 ▫ Traction Grades . . . . . . . . . . . . . . . . . . . . . 513 䡵 Department Of Transportation Uniform Tire Quality Grades . . . . . . . . . . . . . . . . . . . . . . . . 513 ▫ Temperature Grades . . . . . . . . . . . . . . . . . . 514 ▫ Treadwear . . . . . . . . . . . . . . . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE 507 the service advisor and list the items in order of priority. At many authorized dealers, you may obtain a rental vehicle at a minimal daily charge. If you need a rental, it Prepare For The Appointment is advisable to make these arrangements when you call If you’re having warranty work done, be sure to have the for an appointment. right papers with you. Take your warranty folder. All work to be performed may not be covered by the IF YOU NEED ASSISTANCE warranty.
508 IF YOU NEED CONSUMER ASSISTANCE This is why you should always talk to an authorized • Vehicle delivery date and mileage dealer’s service manager first. Most matters can be reChrysler Group LLC Customer Center solved with this process. P.O. Box 21–8004 • If for some reason you are still not satisfied, talk to the Auburn Hills, MI 48321–8004 general manager or owner of the authorized dealer- Phone: (800) 247–9753 ship. They want to know if you need assistance. Chrysler Canada Inc.
IF YOU NEED CONSUMER ASSISTANCE Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommunication Devices for the Deaf) equipment at its customer center. Any hearing or speech impaired customer, who has access to a TDD or a conventional teletypewriter (TTY) in the United States, can communicate with the manufacturer by dialing 1–800–380–CHRY.
510 IF YOU NEED CONSUMER ASSISTANCE We appreciate that you have made a major investment when you purchased the vehicle. An authorized dealer has also made a major investment in facilities, tools, and training to assure that you are absolutely delighted with the ownership experience. You’ll be pleased with their sincere efforts to resolve any warranty issues or related concerns.
IF YOU NEED CONSUMER ASSISTANCE If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your authorized dealer, and the manufacturer. 511 Transport Canada, Motor Vehicle Defect Investigations and Recalls, 2780 Sheffield Road, Ottawa, Ontario K1B 3V9.
512 IF YOU NEED CONSUMER ASSISTANCE acquaint you with specific Chrysler Group LLC vehicles. Included are starting, operating, emergency and maintenance procedures as well as specifications, capabilities and safety tips. vehicle, system, and/or components is written in straightforward language with illustrations, diagrams, and charts. • Diagnostic Procedure Manuals Diagnostic Procedure Manuals are filled with diagrams, charts and detailed illustrations.
IF YOU NEED CONSUMER ASSISTANCE DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES The following tire grading categories were established by the National Highway Traffic Safety Administration. The specific grade rating assigned by the tire’s manufacturer in each category is shown on the sidewall of the tires on your vehicle. 513 significantly from the norm due to variations in driving habits, service practices, and differences in road characteristics and climate.
514 IF YOU NEED CONSUMER ASSISTANCE Temperature Grades The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
INDEX 10
516 INDEX About Your Brakes . . . . . . . . . . . . . . . . . . . . . . . 335 ABS (Anti-Lock Brake System) . . . . . . . . . . . . . . 338 Adaptive Cruise Control (ACC) (Cruise Control) . . 162 Adding Engine Coolant (Antifreeze) . . . . . . . . . . 446 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 379 Adding Washer Fluid . . . . . . . . . . . . . . . . . . . . . 440 Additives, Fuel . . . . . . . . . . . . . . . . . . . . . . . . . 377 Adjustable Pedals . . . . . . . . . . . . . . . . .
INDEX Auto Unlock, Doors . . . . . . . . . . . . . . . . . . . . . . . 34 Auto Up Power Windows . . . . . . . . . . . . . . . . . . 41 Automatic Dimming Mirror . . . . . . . . . . . . . . . . . 92 Automatic Door Locks . . . . . . . . . . . . . . . . . . . 32,34 Automatic Headlights . . . . . . . . . . . . . . . . . . . . 145 Automatic Oil Change Indicator . . . . . . . . . . 219,236 Automatic Temperature Control (ATC) . . . . . . . . . 296 Automatic Transaxle Special Additives . . . . . . . . . . . . . . .
518 INDEX Fluid Check . . . . . . . . . . . . . . . . . . . . . . . 450,483 Master Cylinder . . . . . . . . . . . . . . . . . . . . . . . 450 Parking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 335 Warning Light . . . . . . . . . . . . . . . . . . . . . . . . 222 Brakes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 449 Brake/Transmission Interlock . . . . . . . . . . . . . . . 317 Break-In Recommendations, New Vehicle . . . . . . . . 80 Brightness, Interior Lights . . . . . .
INDEX Coin Holder . . . . . . . . . . . . . . . . . . Cold Weather Operation . . . . . . . . . . Compact Disc (CD) Maintenance . . . . Compact Spare Tire . . . . . . . . . . . . . Compass . . . . . . . . . . . . . . . . . . . . . Compass Calibration . . . . . . . . . . . . Compass Variance . . . . . . . . . . . . . . Computer, Trip/Travel . . . . . . . . . . . Connector UCI . . . . . . . . . . . . . . . . . . . . . . . Universal Consumer Interface (UCI) Conserving Fuel . . . . . . . . . . . . . . .
520 INDEX Deck Lid, Power Release . . . . . . . . . . . . . . . . . . . 43 Defroster, Rear Window . . . . . . . . . . . . . . . . . . . 206 Defroster, Windshield . . . . . . . . . . . . . . . . 83,294,300 Delay (Intermittent) Wipers . . . . . . . . . . . . . . . . . 151 Diagnostic System, Onboard . . . . . . . . . . . . . . . . 426 Dimmer Switch, Headlight . . . . . . . . . . . . . . . . . 149 Dipsticks Oil (Engine) . . . . . . . . . . . . . . . . . . . . . . . . . . 430 Power Steering . . . . . . . . . .
INDEX Emergency, In Case of Freeing Vehicle When Stuck . . . . . . . . . . . . . . . 417 Hazard Warning Flasher . . . . . . . . . . . . . . . . . 400 Jacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 401 Jump Starting . . . . . . . . . . . . . . . . . . . . . . . . . 413 Overheating . . . . . . . . . . . . . . . . . . . . . . . . . . 400 Towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 418 Emergency Trunk Release . . . . . . . . . . . . . . . . . . .
522 INDEX System . . . . . . . . . . . . . . . . . . . . . . . 81,441 Fluid Leaks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84 Folding Mirrors . . . . . . . . . . . . . . . . . . . 93 Fluid Level Checks Automatic Transmission . . . . . . . . . . . . . . . . . 452 Lighting . . . . . . . . . . . . . . . . . . . . . . . . 144 Brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 450 Lights . . . . . . . . . . . . . . . . . . . . . . . . . . 84 Cooling System . . . . . . . . . . .
INDEX Filler Cap (Gas Cap) . . . . . . . . . . . . . . . . . . . . 379 Gasoline . . . . . . . . . . . . . . . . . . . . . . . . . . . . 374 Gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 225 Materials Added . . . . . . . . . . . . . . . . . . . . . . . 377 Methanol . . . . . . . . . . . . . . . . . . . . . . . . . . . . 375 Octane Rating . . . . . . . . . . . . . . . . . . . . . . 374,482 Requirements . . . . . . . . . . . . . . . . . . . . . . . . . 374 Saver Mode . . . . . . . . . . .
524 INDEX Hazard Warning Flasher . . . . . . . . . . . . . . . . . . . 400 Head Restraints . . . . . . . . . . . . . . . . . . . . . . . . . 132 Head Rests . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132 Headlight Washers . . . . . . . . . . . . . . . . . . . . . . . 440 Headlights . . . . . . . . . . . . . . . . . . . . . . . . . . . . 472 Automatic . . . . . . . . . . . . . . . . . . . . . . . . . . . 145 Bulb Replacement . . . . . . . . . . . . . . . . . . . . . . 470 Cleaning . . . . . . .
INDEX Instrument Panel Lens Cleaning . . . . . . . . . . . . . 459 Integrated Power Module (Fuses) . . . . . . . . . . . . 460 Interior Appearance Care . . . . . . . . . . . . . . . . . . 458 Interior Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . 460 Interior Lights . . . . . . . . . . . . . . . . . . . . . . . . . . 149 Intermittent Wipers (Delay Wipers) . . . . . . . . . . . 151 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Jack Location . . . . . Jack Operation . .
526 INDEX Automatic Headlights . . . . . . . . . . . . . . . . . . . 145 Brake Assist Warning . . . . . . . . . . . . . . . . . . . 344 Brake Warning . . . . . . . . . . . . . . . . . . . . . . . . 222 Bulb Replacement . . . . . . . . . . . . . . . . . . . 468,470 Courtesy/Reading . . . . . . . . . . . . . . . . . . . 149,189 Cruise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 216 Daytime Running . . . . . . . . . . . . . . . . . . . . . . 147 Dimmer Switch, Headlight . . . . . . . . . . .
INDEX SmartBeams . . . . . . . . . . . . . . . . . . . . . . . . . . 146 Tire Pressure Monitoring (TPMS) . . . . . . . . 226,365 Traction Control . . . . . . . . . . . . . . . . . . . . . . . 344 Turn Signal . . . . . . . . . . . . . . . . . . . . . . 84,148,216 Vanity Mirror . . . . . . . . . . . . . . . . . . . . . . . . . . 96 Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 228 Warning (Instrument Cluster Description) . . . . . 216 Load Leveling System . . . . . . . . . . . . . . . . .
528 INDEX Methanol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 375 Mini-Trip Computer . . . . . . . . . . . . . . . . . . . . . . 236 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91 Automatic Dimming . . . . . . . . . . . . . . . . . . . . . 92 Electric Powered . . . . . . . . . . . . . . . . . . . . . . . 94 Electric Remote . . . . . . . . . . . . . . . . . . . . . . . . 94 Exterior Folding . . . . . . . . . . . . . . . . . . . . . . . . 93 Heated . . . . . . . .
INDEX Recommendation . . . . . . . . . . . . . . . . . . . 431,480 Synthetic . . . . . . . . . . . . . . . . . . . . . . . . . . . . 433 Viscosity . . . . . . . . . . . . . . . . . . . . . . . . . 432,480 Oil Filter, Change . . . . . . . . . . . . . . . . . . . . . . . . 433 Oil Filter, Selection . . . . . . . . . . . . . . . . . . . . . . . 433 Onboard Diagnostic System . . . . . . . . . . . . . . 426,427 Opener, Garage Door (HomeLink威) . . . . . . . . . . . 190 Operating Precautions . . . . . . . . . . .
530 INDEX Power Steering Fluid . . . . . . . . . . . . . . . . . . . . . 483 Pregnant Women and Seat Belts . . . . . . . . . . . . . . 55 Preparation for Jacking . . . . . . . . . . . . . . . . . . . . 404 Pretensioners Seat Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Programmable Electronic Features . . . . . . . . . . . . 245 Programming Transmitters (Remote Keyless Entry) . . . . . . . . . . . . . . . . . . . . 20 Radial Ply Tires . . . . . . . . . . . . . . .
INDEX 531 Reporting Safety Defects . . . . . . . . . . . . . . . . . . . 510 Seat Belts . . . . . . . . . . . . . . . . . . . . . . . . . . 45,46,82 Adjustable Upper Shoulder Anchorage . . . . . . . . 51 Resetting Oil Change Indicator . . . . . . . . . . . 219,236 And Pregnant Women . . . . . . . . . . . . . . . . . . . 55 Restraint, Head . . . . . . . . . . . . . . . . . . . . . . . . . 132 Child Restraint . . . . . . . . . . . . . . . . . . . 71,72,73,77 Restraints, Child . . . . . . . . . . . . . . . .
532 INDEX Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138 Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130 Rear Folding . . . . . . . . . . . . . . . . . . . . . . . . . 136 Reclining . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131 Seatback Release . . . . . . . . . . . . . . . . . . . . . . . 136 Tilting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130 Security Alarm (Theft Alarm) . . . . . . . . . . . . . . . .
INDEX Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27,309 Automatic Transmission . . . . . . . . . . . . . . . . . 309 Cold Weather . . . . . . . . . . . . . . . . . . . . . . . . . 312 Engine Fails to Start . . . . . . . . . . . . . . . . . . . . 312 Remote . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Starting and Operating . . . . . . . . . . . . . . . . . . . . 309 Starting Procedures . . . . . . . . . . . . . . . . . . . . . . 309 Steering Column Controls . . . .
534 INDEX Tire Markings . . . . . . . . . . . . . . . . . . . . . . . . . . 345 Tire Safety Information . . . . . . . . . . . . . . . . . . . . 345 Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84,355,513 Aging (Life of Tires) . . . . . . . . . . . . . . . . . . . . 361 Air Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . 355 Changing . . . . . . . . . . . . . . . . . . . . . . . . . 401,404 Compact Spare . . . . . . . . . . . . . . . . . . . . . . . . 358 Flat Changing . . . .
INDEX Towing Vehicle Behind a Motor Home . . . . . . . . . 396 Traction Control . . . . . . . . . . . . . . . . . . . . . . . . . 340 Trailer Towing . . . . . . . . . . . . . . . . . . . . . . . . . . 384 Cooling System Tips . . . . . . . . . . . . . . . . . . . . 396 Hitches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 386 Minimum Requirements . . . . . . . . . . . . . . . . . 389 Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 395 Trailer and Tongue Weight . . . . . . .
536 INDEX Unleaded Gasoline . . . . . . . . . . . . . . . . . . . . . . . 374 Warranty Information . . . . . . . . . . . . . . . . . . . . . 510 Untwisting Procedure, Seat Belt . . . . . . . . . . . . . . 52 Washer, Adding Fluid . . . . . . . . . . . . . . . . . . . . . 440 Washers, Windshield . . . . . . . . . . . . . . . . . . 152,440 Vanity Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 Washing Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . 455 Variance, Compass . . . . . .
Chrysler Group LLC 10C481-126-AC 3rd Edition Printed in U.S.A.
