OWNER’S MANUAL 2009
VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name Chrysler LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefor. DRIVING AND ALCOHOL Drunken driving is one of the most frequent causes of accidents. Your driving ability can be seriously impaired with blood alcohol levels far below the legal minimum. If you are drinking, don’t drive. Ride with a designated non-drinking driver, call a cab, a friend, or use public transportation.
SECTION TABLE OF CONTENTS PAGE 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .97 3 4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION CONTENTS 䡵 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 Vehicle Identification Number . . . . . . . . . . . . . . . 6 䡵 How To Use This Manual . . . . . . . . . . . . . . . . . . 4 䡵 Vehicle Modifications/Alterations . . . . . . . . . . . . 7 䡵 Warnings And Cautions . . . . . . . . . . . . . . . . . . .
4 INTRODUCTION INTRODUCTION This Owner’s Manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your vehicle. It is supplemented by a Warranty Information Booklet and various customer-oriented documents. You are urged to read these publications carefully. Following the instructions and recommendations in this manual will help assure safe and enjoyable operation of your vehicle.
INTRODUCTION 5 1
6 INTRODUCTION WARNINGS AND CAUTIONS This Owner’s Manual contains WARNINGS against operating procedures that could result in an accident or bodily injury. It also contains CAUTIONS against procedures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important information. Observe all Warnings and Cautions.
INTRODUCTION 7 VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS 䡵 A Word About Your Keys . . . . . . . . . . . . . . . . . 12 䡵 Remote Starting System — If Equipped . . . . . . . 28 ▫ Wireless Ignition Node (WIN) . . . . . . . . . . . . . 12 ▫ How To Use Remote Start . . . . . . . . . . . . . . . 28 䡵 Sentry Key威 Immobilizer System . . . . . . . . . . . . 15 䡵 Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 ▫ Replacement Keys . . . . . . . . . . . . . . . . . . . . .
10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 䡵 Sliding Side Door . . . . . . . . . . . . . . . . . . . . . . . 42 ▫ Power Sliding Side Door — If Equipped . . . . . 43 ▫ Sliding Side Door Child Protection Lock . . . . . 47 䡵 Liftgate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 ▫ Power Liftgate — If Equipped . . . . . . . . . . . . 50 䡵 Storage Bin Safety Warning . . . . . . . . . . . . . . . . 53 ▫ Safety Warning . . . . . . . . . . . . . . . . . . . . . . . 53 䡵 Occupant Restraints . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 䡵 Rear Seat Delete Feature (Commercial Vehicles Only) — If Equipped. . . . . . . . . . . . . . . . . . . . . 90 ▫ Restraining Infants And Small Children With Seat Delete Feature (Commercial Vehicles Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91 䡵 Engine Break-In Recommendations . . . . . . . . . . 93 䡵 Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94 ▫ Safety Checks You Should Make Inside The Vehicle . . . . . . .
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS Your vehicle uses a keyless ignition system. This system consists of a Remote Keyless Entry (RKE) transmitter with integrated ignition key and a Wireless Ignition Node (WIN) with integral ignition switch. You can insert the double-sided key into the ignition switch with either side up. Wireless Ignition Node (WIN) The Wireless Ignition Node (WIN) operates similarly to an ignition switch.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 Integrated Ignition Key The integrated ignition key operates the ignition switch. It also contains the Remote Keyless Entry (RKE) transmitter and a Valet Key, which stores in the rear of the RKE transmitter. 2 The Valet Key allows for entry into the vehicle should the battery in the vehicle or the RKE transmitter go dead. The Valet Key is also for locking the glove box. You can keep the Valet Key with you when valet parking.
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Tip Start Feature 1. Do not press the accelerator pedal during this process. 2. Insert the integrated ignition key into the ignition switch. 3. Turn the ignition switch to the START position and release it as soon as the starter engages. The starter motor will continue to run and will disengage automatically when the engine begins running. Ignition Key Removal Place the shift lever in PARK. Turn the ignition key to the OFF position and then remove the key.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 Key-In-Ignition Reminder If you open the driver’s door with the integrated ignition key in the ignition, a chime will sound to remind you to remove the key. NOTE: The Key-In-Ignition reminder only sounds when the integrated ignition key is placed in the OFF or ACC position. SENTRY KEY姞 IMMOBILIZER SYSTEM The Sentry Key威 Immobilizer system prevents unauthorized vehicle operation by disabling the engine. The system does not need to be armed or activated.
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: • The Sentry Key威 Immobilizer system is not compatible with aftermarket remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection. • Exxon/Mobil Speedpass™, additional RKE transmitters, or any other transponder-equipped components on the same key chain will not cause a fault unless the additional part is physically held against the RKE transmitter being used to start the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 NOTE: When having the Sentry Key威 Immobilizer system serviced, bring all vehicle RKE transmitters with you to the authorized dealer. Customer Key Programming If you have two valid RKE transmitters with integrated keys, you can program new RKE transmitters to the system by performing the following steps: 1.
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: If a programmed key is lost, see your authorized dealer to have all remaining keys erased from the system’s memory. This will prevent the lost key from starting your vehicle. The remaining keys must then be reprogrammed. All vehicle keys must be taken to an authorized dealer at the time of service to be reprogrammed. General Information The Sentry Key威 system complies with FCC rules Part 15 and with RSS-210 of Industry Canada.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 Arming The System Remove the key from the ignition switch and either press a power door lock switch while the driver or passenger door is open, or press the LOCK button on the Remote Keyless Entry (RKE) transmitter. After all the doors are locked and closed, the Vehicle Security Light in the instrument cluster will flash rapidly to signal that the system is arming.
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If the Vehicle Security Alarm system is armed and the battery becomes disconnected, the system will remain armed when the battery is reconnected; the exterior lights will flash, the horn will sound. If this occurs, disarm the system. Tamper Alert If something has triggered the system in your absence, the horn will sound three times when you unlock the doors and the Vehicle Security Light will flash for 30 seconds. Check the vehicle for tampering.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 REMOTE KEYLESS ENTRY (RKE) — IF EQUIPPED This system allows you to lock or unlock the doors and liftgate, and activate the Panic Alarm, optional power liftgate, left power sliding door, and right power sliding door from distances up to about 23 ft (7 m) using a hand-held radio RKE transmitter. The RKE transmitter need not be pointed at the vehicle to activate the system.
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE (optional), power sliding doors, Remote Start feature (optional). Some features can be programmed to the customers preferences. For example, flash headlights or sound horn on LOCK. Remote Unlock Doors and Liftgate Press and release the UNLOCK button on the RKE transmitter once to unlock the driver’s door or twice to unlock all doors and liftgate. The Illuminated Entry system also turns on.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 • For vehicles not equipped with the EVIC, the Remote Unlock feature can be enabled or disabled by performing the following steps: 1. Perform this operation while standing outside the vehicle. 2. Press the LOCK button for five to ten seconds. 3. While the LOCK button is pressed, (after five seconds) press the UNLOCK button. Release both buttons.
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. While the LOCK button is pressed (after five seconds) press the PANIC button. Release both buttons. The Sound Horn with Remote Key Lock feature can be reactivated by repeating the above steps or by performing the steps in the optional Electronic Vehicle Information Center (EVIC), Personal Settings (CustomerProgrammable Features) section of this manual.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 If equipped with a rear interior switch on the left rear pillar, pushing this switch once will close the liftgate only. The liftgate cannot be opened from this switch. Open/Close Power Left Power Sliding Door — If Equipped Press the LEFT Power Sliding Door button twice on the RKE transmitter within five seconds to Open/Close Power Left Power Sliding Door.
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The table below explains the Lamp Flash options. Function Lock Unlock 1st Press Unlock All Doors Left Side Right Side Liftgate Which Turn Signal Lamps All Left Side All Left Side Right Side All Number of Flashes 1 2 2 2 2 2 Programming Additional RKE Transmitters Refer to Sentry Key威 Immobilizer System “Customer Key Programming.” If you do not have a programmed RKE transmitter, contact your authorized dealer for details.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 3. Reposition the access door panel over the battery opening and snap into place. General Information This device complies with Part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired operation. RKE Transmitter Battery Replacement 1– Battery Access Door 2.
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE REMOTE STARTING SYSTEM — IF EQUIPPED The Remote Starting system conveniently starts the engine from outside the vehicle by using the Remote Keyless Entry (RKE) transmitter while maintaining the Vehicle Security Alarm system. The Remote Starting system has a targeted range of 328 ft (100 m). In order to Remote Start your vehicle, the hood, liftgate, and all the doors must be closed and the shift lever in PARK.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 • For security, power window and power sunroof operation (if equipped) are disabled when the vehicle is in the Remote Start mode. • The engine can be started two consecutive 15-minute cycles with the RKE transmitter. However, the ignition switch must be turned to the ON position before you can repeat the start sequence. Remote Starting Button NOTE: • If your power door locks were unlocked, Remote Start will automatically lock the doors.
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Exit Remote Start Mode and Drive the Vehicle Before the end of the 15-minute cycle, press and release the UNLOCK button on the RKE transmitter to unlock the doors and disarm the Vehicle Security Alarm (if equipped). Then, prior to the end of the 15-minute cycle, insert the key into the ignition switch and turn the switch to the ON position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 When to Reset Remote Start The vehicle can be started remotely up to a maximum of two times. The vehicle is also allowed a maximum of one failed start, where the Remote Starting sequence was initiated but the engine stopped cranking without starting.
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • For personal security and safety in the event of an accident, lock the vehicle doors as you drive as well as when you park and leave the vehicle. • When leaving the vehicle always remove the key from the ignition switch, and lock your vehicle. Do not leave unattended children in the vehicle, or with access to an unlocked vehicle. Unsupervised use of vehicle equipment may cause severe personal injuries and death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 Power Door Locks — If Equipped A power door lock switch is on each front door trim panel. Use this switch to lock or unlock the doors. Driver Power Door Lock Switch 1 - Unlock 2 - Lock If you press the power door lock switch while the key is in the ignition, and any front door is open, the power locks will not operate. This prevents you from accidentally locking your keys in the vehicle. Removing the key or closing the door will allow the locks to operate.
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lock Doors Automatically — If Equipped If the Lock Doors Automatically feature is enabled, your door locks will lock automatically when the vehicle’s speed exceeds 15 mph (24 km/h).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 3. Place the key into the ignition. 4. Within 15 seconds, cycle the ignition key from the LOCK position to the ON/RUN position a minimum of four times, ending in the LOCK position (do not start the engine). 5. Within 30 seconds, press the driver’s door lock switch in the LOCK direction. 6. A single chime will be heard to indicate the feature has been disabled. 7. To reactivate this feature, repeat the above steps. 8.
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The Unlock Doors Automatically On Exit feature can be enabled or disabled by performing the following procedure: 1. Enter your vehicle and close all doors. 2. Fasten your seat belt. (Fastening the seat belt will cancel any chimes that may be confusing during this programming procedure.) 3. Insert the key into the ignition switch. 4.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 The Remote Power Unlock On First Press feature can be enabled or disabled by performing the following procedure: 1. Perform this operation while standing outside the vehicle. WINDOWS Power Vent Windows — If Equipped Switches on the driver’s door trim panel let the driver operate the two vent windows from the driver’s seat. 2. Press the LOCK button for five to ten seconds. 3. While the LOCK button is pressed, (after five seconds) press the UNLOCK button.
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Power Windows You can control either the front or rear windows using switches located on the driver’s door trim panel. The switches will operate only when the ignition switch is in the ON or ACC position and during power accessory delay.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 Power Window Lockout Switch — If Equipped The driver may lock out all power windows by depressing the bar switch just below the power window switches. Power Window Lockout Switch Front Passenger Power Window Switch There is a single switch on the front passenger’s door trim panel which operates the passenger door window and locks and unlocks all doors.
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Sliding Side Door Power Window Switch Second row passengers may power the sliding door window by a single switch on the door handle assembly. NOTE: Please note that the sliding door windows do not fully recline, stopping several inches above the window sill. The switches will operate only when the ignition switch is in the ON or ACC position. Auto Down Feature — If Equipped The front window switches may be equipped with an auto down feature.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 Auto Up Feature With Anti–Pinch Protection — If Equipped The front Driver switch may be equipped with an Auto Up feature. Lift the window switch to the second detent, release, and the window will go up automatically. To stop the window from going all the way up during the Auto Up operation, push down on the switch briefly. To close the window part way, lift the window switch to the first detent and release when you want the window to stop.
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Push the window switch down firmly to the second detent to open the window completely and continue to hold the switch down for an additional two seconds after the window is fully open. Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 • There is a hold-open latch that is activated when the sliding door is fully opened. This latch will keep your sliding door open on any incline. To close the sliding door after the hold-open latch is activated, you must rock the inside handle forward or pull outward on the outside handle. Always make sure that the sliding door is fully latched anytime the vehicle is in motion.
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To avoid unintentional operation of the power sliding doors from the rear seats, press the power sliding door master lock button, located in the overhead console, to disable the switches and handles for the rear seat passengers. NOTE: • The power sliding side door switches will not open if the shift lever is in gear or the vehicle speed is above 0 mph (0 km/h).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 door switch is pressed. To close the door, wait until it is fully open and then press the switch again. • The power sliding side door switches will not operate if the shift lever is in gear or the vehicle speed is above 0 mph (0 km/h). • If the power sliding door encounters multiple obstructions within the same cycle, the system will automatically stop and must be opened or closed manually.
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Power Sliding Side Door Master Lock Switch The power sliding side door may also be opened by pressing the switches on the overhead console or the switch located on the trim panel just in front of the sliding door.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 Sliding Side Door Child Protection Lock To provide a safer environment for small children riding in the rear seats, the sliding doors are equipped with a Child Protection Door Lock system. 2 NOTE: When the Child Protection Door Lock system is engaged, the door can be opened only by using the outside door handle even though the inside door lock is in the unlocked position. To Engage the Child Protection Door Lock 1. Open the sliding side door. 2.
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • When the Child Protection Door Lock system is engaged, (even if the inside door lock is in the unlocked position) the door can be opened only by using the outside door handle, the RKE transmitter, the switches on the overhead console or the switches located on the trim panel just in front of the power sliding door.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 NOTE: • After setting the Child Protection Door Lock system, always test the door from the inside to make certain it is in the desired position. • The power sliding side door switches will not operate if the vehicle is in gear or the vehicle speed is above 0 mph (0 km/h).
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Power Liftgate — If Equipped The power liftgate may be opened manually or by using the button on the Remote Keyless Entry (RKE) transmitter. Press the button on the transmitter twice within five seconds, to open the power liftgate. When the liftgate is fully open, pressing the button twice within five seconds, a second time, will close the liftgate. The power liftgate may also be opened and closed by pressing the button located on the overhead console.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 2 Overhead Console Master Power Switch 1 — Left Door 2 — Liftgate 3 — Right Door 4 — Master Lock The power liftgate may be closed by pressing the button, located in the upper left trim in the liftgate opening. Pushing once will only close the liftgate. This button cannot be used to open the liftgate.
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! During power operation, personal injury or cargo damage may occur. Ensure the liftgate travel path is clear. Make sure the liftgate is closed and latched before driving away. NOTE: • If anything obstructs the power liftgate while it is closing or opening, the liftgate will automatically reverse to the closed or open position, provided it meets sufficient resistance. • There are also pinch sensors attached to the side of the liftgate opening.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 • If the power liftgate encounters multiple obstructions within the same cycle, the system will automatically stop and must be opened or closed manually. WARNING! • Driving with the liftgate open can allow poisonous exhaust gases into your vehicle. You and your passengers could be injured by these fumes. Keep the liftgate closed when you are operating the vehicle.
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • Do not operate the storage bin covers while the vehicle is in motion. • Do not use a storage bin latch as a tie down. CAUTION! The storage bin cover must be flat and locked to avoid damage from contact with the front seat tracks, which have minimal clearance to the cover.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 OCCUPANT RESTRAINTS Some of the most important safety features in your vehicle are the restraint systems: • Front seat belt retractors incorporate pretensioners to enhance occupant protection by managing occupant energy during an impact event.
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Please pay close attention to the information in this section. It tells you how to use your restraint system properly to keep you and your passengers as safe as possible. WARNING! In a collision, you and your passengers can suffer much greater injuries if you are not properly buckled up. You can strike the interior of your vehicle or other passengers, or you can be thrown out of the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 WARNING! WARNING! (Continued) • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • Be sure everyone in your vehicle is in a seat and using a seat belt properly. • Wearing a seat belt incorrectly is dangerous.
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. The seat belt latch plate is near the seatback of the front seats and next to your arm in the rear seats. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to allow the belt to go around your lap. Pulling Out Belt and Latch Plate WARNING! • A belt that is worn under your arm is very dangerous. Your body could strike the inside surfaces of the vehicle in a collision, increasing head and neck injury.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click”. WARNING! • A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you as well.
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision. WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 WARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Seat belt assemblies must be replaced after a collision if they have been damaged (bent retractor, torn webbing, etc.).
62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE As a guide, if you are shorter than average you will prefer a lower position, and if you are taller than average you will prefer a higher position. When you release the anchorage, try to move it up or down to make sure that it is locked in position. How to Use the Automatic Locking Mode Automatic Locking Retractors (ALR) Mode — If Equipped In this mode, the shoulder belt is automatically prelocked.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 by assuring that the belt is tight about the occupant early in a collision. Pretensioners work for all size occupants, including those in child restraints. Once the warning is triggered, BeltAlert威 will continue to chime and flash the Seat Belt Warning Light for 96 seconds or until the driver’s seat belt is buckled. NOTE: These devices are not a substitute for proper seat belt placement by the occupant.
64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Turn the ignition switch to the ON position (engine does not need to be running), and wait for the Seat Belt Warning Light to turn off. 3. Within 60 seconds of turning the ignition switch to the ON/RUN position, unbuckle and then re-buckle the driver’s seat belt at least three times within 60 seconds, ending with the seat belt buckled. NOTE: Watch for the Seat Belt Warning Light to turn on while unbuckling and off while re-buckling the seat belt. 4.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 WARNING! Using a seat belt extender when not needed can increase the risk of injury in a collision. Only use when the lap belt is not long enough when it is worn low and snug, and in the recommended seating positions. Remove and store the extender when not needed. Supplemental Restraint System (SRS) - Airbag This vehicle has airbags for both the driver and front passenger as a supplement to the seat belt restraint systems.
66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag System Components The airbag system consists of the following: • Supplemental Seat Side Airbag Inflatable Curtains (SABIC) (if equipped) • Occupant Restraint Controller (ORC) Front Seat Airbag Features The front airbag system has dual-stage driver and front passenger airbags. This system provides output appropriate to the level of crash severity as determined by the Occupant Restraint Controller (ORC) and the impact sensors at the front of the car.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 Driver Airbag Special Features Driver airbag deployment and force level is controlled by the driver’s seat position as well as impact severity. Use of special inflators result in a very compact driver’s side airbag. In addition to the small size, the inflating gases exit through strategically placed vents, which direct the gas away from the occupant.
68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Supplemental Side Airbag Inflatable Curtain (SABIC) — If Equipped SABIC Airbags offer side-impact and vehicle rollover protection to front and rear seat outboard occupants in addition to that provided by the body structure. Each airbag features inflated chambers placed adjacent to the head of each outboard occupant that reduce the potential for side-impact head injuries. The curtains deploy downward, covering both windows on the impact side.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 collisions, both the front and side airbags may be triggered. However, even in collisions where the airbags work, you need the seat belts to keep you in the right position for the airbags to protect you properly. Here are some simple steps you can take to minimize the risk of harm from a deploying airbag. Children 12 years old and younger should always ride buckled up in a rear seat.
70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If the airbag system in this vehicle needs to be modified to accommodate a disabled person, contact the Customer Center. Phone numbers are provided under ⬙If You Need Assistance⬙ in Section 9 of this manual. WARNING! • Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly. In some collisions, the airbags won’t deploy at all.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 or ON position. These include all of the components listed above except the steering wheel and column, instrument panel, and seat belt reminder light. If the key is in the OFF position, in the ACC position, or not in the ignition, the airbags are not on and will not inflate. The ORC contains a backup power supply system that will deploy the airbags even if the battery loses power or it becomes disconnected prior to deployment.
72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Acceleration Sensors Acceleration Sensors trigger airbag deployment based on dramatic acceleration change of the vehicle. NOTE: The ORC will also detect and protect for rollover when equipped with SABIC airbags. In a rollover the SABIC airbags will deploy on both sides of the vehicle. Pressure Sensors Pressure Sensors trigger airbag deployment based on door cavity pressure changes.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 If A Deployment Occurs The airbag systems are designed to deploy when the Occupant Restraint Controller (ORC) detects a moderateto-severe collision, to help restrain the driver, front passenger and rear passengers, and then immediately deflate. NOTE: A frontal collision that is not severe enough to need airbag protection will not activate the system. This does not mean something is wrong with the airbag system.
74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Deployed airbags and seat belt pretensioners cannot protect you in another collision. Have the airbags, seat belt pretensioners, and the front passenger seat belt retractor assembly replaced by an authorized dealer as soon as possible. Also, have the Occupant Restraint Controller (ORC) system serviced as well. Maintaining Your Airbag System WARNING! • Modifications to any part of the airbag system could cause it to fail when you need it.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 WARNING! (Continued) • Do not attempt to modify any part of your advanced airbag system. The airbag may inflate accidentally or may not function properly if modifications are made. Take your vehicle to an authorized dealer for any advanced airbag system service. If your seat, including your trim cover and cushion, needs to be serviced in any way (including removal or loosening/tightening of seat attachment bolts), take the vehicle to your authorized dealer.
76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE located on the inside of the fuse block cover for the proper airbag fuses. See your authorized dealer if the fuse is good.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77 the vehicle owner or lessee) before accessing the electronic data stored, unless ordered to download data by a court with legal jurisdiction (i.e., pursuant to a warrant). A copy of the data will be provided to the custodial entity upon request. General data that does not identify particular vehicles or crashes may be released for incorporation in aggregate crash databases, such as those maintained by the U.S. government and various states.
78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Engine control status (including engine speed) • Transmission gear selection • Cruise control status • Traction/stability control status • Tire Pressure Monitoring System status (if equipped) Integrated Child Booster Seat — If Equipped The Integrated Child Booster Seat (if equipped) is located in each second-row passenger seat.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 79 NOTE: The lap portion of the seat belt should be low on the hips and as snug as possible. 5. Once the seat belt is long enough to fit properly, insert the latch plate into the buckle until you hear a “click.” 6. To remove the slack from the lap belt, pull upward on the shoulder portion of the seat belt. Booster Seat Position 2. Place the child upright in the seat with their back firmly against the seatback. 3.
80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE the instructions are not with the seat or in the Owner’s Manual Package, replacement instruction can be obtained. Integrated Child Booster Seat 7. To release the seat belt, push the red button on the buckle. Integrated Child Seat — If Equipped Operating instructions for the second row bench seat with Integrated Child Seat are included with the seat.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 81 To obtain Integrated Child Seat replacement instructions: Refer to the Publication order forms at the back of this manual and specify publication number 81–226–0919. Child Restraints Everyone in your vehicle needs to be buckled up all the time, including babies and children. Every state in the United States and all Canadian provinces require that small children ride in proper restraint systems. This is the law, and you can be prosecuted for ignoring it.
82 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Safety experts recommend that children ride rearward-facing in the vehicle until they are at least one year old and weigh at least 20 lbs (9 kg). Two types of child restraints can be used rearward-facing: infant carriers and convertible child seats. Both types of child restraints are held in the vehicle by the lap/shoulder belt or the LATCH child restraint anchorage system. Refer to “Lower Anchors and Tether for CHildren (LATCH)” later in this section.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 83 Older Children and Child Restraints Children who weigh more than 20 lbs (9 kg) and who are older than one year can ride forward-facing in the vehicle. Forward-facing child seats and convertible child seats used in the forward-facing direction are for children who weigh 20 to 40 lbs (9 to 18 kg) and who are older than one year. These child seats are also held in the vehicle by the lap/shoulder belt or the LATCH child restraint anchorage system.
84 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE and use the lap belt. Never allow a child to put the shoulder belt under an arm or behind their back. NOTE: For additional information, refer www.seatcheck.org or call 1-866-SEATCHECK. to WARNING! • Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 85 • Carefully follow the instructions that come with the restraint. If you install the restraint improperly, it may not work when you need it. • The passenger seat belts are equipped with cinching latch plates, which are designed to keep the lap portion tight around the child restraint so that it is not necessary to use a locking clip. Pulling up on the shoulder portion of the lap/shoulder belt will tighten the belt.
86 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lower Anchors and Tether for CHildren (LATCH) Each vehicle, except commercial cargo vehicles, is equipped with the child restraint anchorage system called LATCH, which stands for Lower Anchors and Tether for CHildren. Two LATCH child restraint anchorage systems are installed on all second-row seats and in the center position on all third row fold-in-floor seats. Second-row seats also feature tether strap anchorages, located in the rear surface of the seatback.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 87 WARNING! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor positions directly behind the child seat to secure a child restraint top tether strap. Rear Seat Tether Strap Mounting When using the tether anchorages in the center position on third row fold-in-floor seating, ensure that the strap is routed underneath the head restraint and over the seatback.
88 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: • When using the LATCH attaching system to install a child restraint, please ensure that all seat belts not being used for occupant restraints are stowed and out of reach of children. It is recommended that before installing the child restraint, buckle the seat belt so the seat belt is tucked behind the child restraint and out of reach.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 89 To install a child restraint, pull enough of the seat belt webbing from the retractor to route it through the belt path of the child restraint and slide the latch plate into the buckle. Next, pull all the seat belt webbing, until it is fully extracted, from the retractor. Allow the belt to return to the retractor, pulling on the excess webbing to tighten the lap portion about the child restraint.
90 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Transporting Pets Airbags deploying in the front seat could harm your pet. An unrestrained pet could be thrown about and possibly injured, or injure a passenger during panic braking or in a collision. Pets should be restrained in the rear seat in pet harnesses or pet carriers that are secured by seat belts. WARNING! NEVER carry a child in a rear facing infant carrier in a vehicle without rear seats.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 91 This vehicle is equipped with a child restraint tether anchor located on the lower rear of the front passenger seat. Use this tether anchor to secure only forwardfacing child restraints equipped with an upper tether strap. WARNING! Rearward-facing infant restraints must never be secured in the passenger seat of a vehicle with a passenger airbag.
92 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Children more than 40 lbs (18 kg) should be secured in the passenger seat in a child restraint or beltpositioning booster seat with the seat adjusted to the rear most position. Older children who do not use child restraints or belt-positioning booster seats should ride properly buckled in the passenger seat with the seat adjusted to the rearmost position. Never allow children to slide the shoulder belt behind them or under their arm.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 93 WARNING! The vehicle tether anchor is designed to be used with a child restraint only. It should not be used for any other purpose. Before use, inspect the tether anchor strap for nicks, abrasions, discoloration, and loose threads. If these or any other condition that might affect the performance of the strap is observed, DO NOT USE that strap. Personal injury may result. Contact your authorized dealership for a replacement part.
94 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE SAFETY TIPS Safety Checks You Should Make Inside the Vehicle Seat Belts Inspect the seat belt system periodically checking for cuts, frays, and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Front seat belt assemblies must be replaced after a collision. Rear seat belt assemblies must be replaced after a collision if they have been damaged (i.e., bent retractor, torn webbing, etc.).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 95 Periodic Safety Checks You Should Make Outside the Vehicle Tires Examine tires for excessive tread wear or uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread. Inspect tread and sidewall for cuts or cracks. Check wheel nuts for tightness. Check the tires (including spare) for proper pressure. Lights Have someone observe the operation of exterior lights while you work the controls.
96 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! If you are required to drive with the deck lid / liftgate open, make sure that all windows are closed, and the climate control blower switch is set at high speed. DO NOT use the recirculation mode.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 䡵 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102 ▫ Inside Day/Night Mirror — If Equipped . . . . 102 ▫ Automatic Dimming Mirror — If Equipped . . 102 ▫ Outside Mirrors . . . . . . . . . . . . . . . . . . . . . . 103 ▫ Driver’s Auto-Dimming Sideview Mirror — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 104 ▫ Outside Mirror Folding Feature . . . . . . . . . . 104 ▫ Power Mirrors — If Equipped . . . . . . . . . . .
98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Things You Should Know About Your UConnect威 System . . . . . . . . . . . . . . . . . . . . 134 ▫ Easy Access Seating . . . . . . . . . . . . . . . . . . . 153 ▫ General Information . . . . . . . . . . . . . . . . . . . 143 ▫ Swivel ’n Go Premium Seating — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 154 䡵 Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143 ▫ Second Row Bench Seat — If Equipped . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99 ▫ Headlights . . . . . . . . . . . . . . . . . . . . . . . . . 174 䡵 Tilt Steering Column — If Equipped . . . . . . . . 181 ▫ Automatic Headlights — If Equipped . . . . . . 174 䡵 Adjustable Pedals — If Equipped . . . . . . . . . . 182 ▫ Headlights On With Wipers — If Equipped . . 175 䡵 Electronic Speed Control — If Equipped . . . . . . 183 ▫ Headlight Delay — If Equipped . . . . . . . . . . 175 ▫ To Activate . . . . . . . . . . . . . . . . . . . . . . .
100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 䡵 Overhead Consoles . . . . . . . . . . . . . . . . . . . . . 194 ▫ Instrument Panel Cupholders . . . . . . . . . . . . 209 ▫ Front Overhead Console . . . . . . . . . . . . . . . . 194 ▫ Interior Bottle Holders . . . . . . . . . . . . . . . . . 210 䡵 Garage Door Opener — If Equipped . . . . . . . . 197 ▫ Smoker’s Package Kit — If Equipped . . . . . . 210 ▫ Programming HomeLink威 . . . . . . . . . . . . . . 199 䡵 Storage . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 䡵 Console Features . . . . . . . . . . . . . . . . . . . . . . 217 䡵 Umbrella Holder . . . . . . . . . . . . . . . . . . . . . . 224 ▫ Basic Console . . . . . . . . . . . . . . . . . . . . . . . 217 䡵 Load-Leveling System . . . . . . . . . . . . . . . . . . . 224 ▫ Premium Console — If Equipped . . . . . . . . . 218 䡵 Roof Luggage Rack — If Equipped . . . . . . . . . 225 䡵 Electric Rear Window Defroster — If Equipped. . . . . . . . . . . . . . . . . . .
102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Day/Night Mirror — If Equipped A two point pivot system allows for horizontal and vertical adjustment of the mirror. Adjust the mirror to center on the view through the rear window. Headlight glare can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle). The mirror should be adjusted while set in the day position (toward the windshield).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 Outside Mirrors To receive maximum benefit, adjust the outside mirror(s) to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror. WARNING! Automatic Dimming Mirror CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean.
104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Driver’s Auto-Dimming Sideview Mirror — If Equipped This mirror automatically adjusts for annoying headlight glare from vehicles behind you. You can turn this feature on or off by pressing the button at the base of the rearview mirror. Outside Mirror Folding Feature All outside mirrors are hinged and may be moved either forward or rearward to resist damage. The hinges have three detent positions; full forward, full rearward and normal.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 Select a mirror and press one of the four arrows for the direction you want the mirror to move. Driver’s power mirror preselected positions can be controlled by the optional Driver Memory Seat Feature. Refer to “Driver Memory Seat” in Section 3. Heated Power Mirrors — If Equipped These mirrors are heated to melt frost or ice. This feature is activated whenever you turn on the rear window defrost.
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Illuminated Vanity Mirrors — If Equipped An illuminated vanity mirror is located on the sun visor. To use the mirror, rotate the sun visor down and swing the mirror cover upward. The lights turn on automatically. Closing the mirror cover turns off the lights.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 When the vehicle is started, the BSM warning light will be momentarily illuminated in both outside rear view mirrors to let the driver know that the system is operational. The BSM system sensors operate when the vehicle is in any forward gear or REVERSE and enters stand by mode when the vehicle is in PARK. The BSM detection zone covers approximately one lane on both sides of the vehicle (11 ft or 3.35 m).
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The area on the rear fascia where the radar sensors are located must remain free of snow, ice, and dirt/road contamination so that the BSM system can function properly. Do not block the area of the rear fascia where the radar sensors are located with foreign objects (bumper stickers, bicycle racks, etc.). The BSM system notifies the driver of objects in the detection zones by illuminating the BSM warning light located in the outside mirrors.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 The BSM system can also be configured to sound an audible (chime) alert and mute the radio to notify the driver of objects that have entered the detection zones. Refer to “Modes Of Operation” in this section. The BSM system monitors the detection zone from three different entry points (Side, Rear, Front) while driving to see if an alert is necessary. The BSM system will issue an alert during these types of zone entries.
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Entering From The Rear Vehicles that come up from behind your vehicle on either side and enter the rear detection zone with a relative speed of less than 30 mph (48 km/h). Overtaking Traffic If you pass another vehicle slowly (with a relative speed less than 10 mph (16 km/h) and the vehicle remains in the blind spot for approximately 1.5 seconds, the warning light will be illuminated.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 3 Overtaking/Passing The BSM system is designed not to issue an alert on stationary objects such as guardrails, posts, walls, foliage, berms, etc. However, occasionally the system may alert on such objects. This is normal operation and your vehicle does not require service.
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The BSM system will not alert you of objects that are traveling in the opposite direction of the vehicle in adjacent lanes. Opposing Traffic WARNING! The Blind Spot Monitoring system is only an aid to help detect objects in the blind spot zones. The BSM system is not designed to detect pedestrians, bicyclists, or animals.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 NOTE: In a parking lot situation, oncoming vehicles can be obscured by vehicles parked on either side. If the sensors are blocked by other structures or vehicles, the system will not be able to alert the driver. When RCP is on and the vehicle is in REVERSE, the driver is alerted using both the visual and audible alarms, including radio muting.
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Modes Of Operation Three selectable modes of operation are available in the Electronic Vehicle Information Center (EVIC). Refer to “Personal Settings (Customer-Programmable Features) under ⬙Electronic Vehicle Information Center (EVIC)” in Section 4. signal is then activated, and it corresponds to an alert present on that side of the vehicle, an audible chime will also be sounded.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 Blind Spot Alert Off When the BSM system is turned off there will be no visual or audible alerts from either the BSM or RCP systems. NOTE: The BSM system will store the current operating mode when the vehicle is shut off. Each time the vehicle is started the previously stored mode will be recalled and used. HANDS-FREE COMMUNICATION (UConnect姞) — IF EQUIPPED phone number with your cellular phone using simple voice commands (e.g.
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE UConnect威 allows you to transfer calls between the system and your cellular phone as you enter or exit your vehicle and enables you to mute the system’s microphone for private conversation. The UConnect威 system is driven through your Bluetooth威 “Hands-Free profile” cellular phone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 The UConnect威 system is fully integrated with the vehicle’s audio system. The volume of the UConnect威 system can be adjusted either from the radio volume control knob or from the steering wheel radio control (right switch), if so equipped. The radio display will be used for visual prompts from the UConnect威 system such as ⬙CELL⬙ or caller ID on certain radios.
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Help Command If you need assistance at any prompt, or if you want to know your options at any prompt, say ⬙Help⬙ following the beep. The UConnect威 system will play all the options at any prompt if you ask for help. To activate the UConnect威 system from idle, simply press the PHONE button and follow the audible prompts for directions. All UConnect威 system sessions begin with a press of the PHONE button on the radio control head.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 • For identification purposes, you will be prompted to give the UConnect威 system a name for your cellular phone. Each cellular phone that is paired should be given a unique phone name. • You will then be asked to give your cellular phone a priority level between 1 and 7, with 1 being the highest priority. You can pair up to seven cellular phones to your UConnect威 system.
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The system will prompt you to say the name of the person you want to call. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Phonebook New Entry.⬙ • After the ⬙Ready⬙ prompt and the following beep, say the name of the person you want to call. For example, you can say ⬙John Doe,⬙ where John Doe is a previously stored name entry in the UConnect威 phonebook or downloaded phonebook.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 The UConnect威 system will allow you to enter up to 32 names in the phonebook with each name having up to four associated phone numbers and designations. Each language has a separate 32-name phonebook accessible only in that language. In addition, if equipped and supported by your phone, UConnect威 automatically downloads mobile phone’s phonebook.
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • This downloaded phonebook cannot be edited or deleted on the UConnect威. These can only be edited on the mobile phone. The changes are transferred and updated to UConnect威 on the next phone connection. Phonebook Download — Single Entry If equipped and supported by your phone, UConnect威 allows the user to download entries from their phone via Bluetooth威. To use this feature, press the PHONE button and say “Phonebook Download.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 • Press the PHONE button to begin. and a home number, but you can add ”John Doe’s” work number later using the ⬙Phonebook Edit⬙ feature. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Phonebook Edit.⬙ Delete UConnect威 Phonebook Entry • You will then be asked for the name of the phonebook entry that you wish to edit. NOTE: Editing phonebook entries is recommended when the vehicle is not in motion.
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After you enter the name, the UConnect威 system will ask you which designation you wish to delete: home, work, mobile, pager, or all. Say the designation you wish to delete. • Note that only the phonebook entry in the current language is deleted. • Automatic downloaded phonebook entries cannot be deleted or edited. Delete/Erase “All” UConnect威 Phonebook Entries • Press the PHONE button to begin.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 • The UConnect威 system will then prompt you as to the number designation you wish to call. • The selected number will be dialed. Phone Call Features The following features can be accessed through the UConnect威 system if the feature(s) are available on your cellular service plan. For example, if your cellular service plan provides three-way calling, this feature can be accessed through the UConnect威 system.
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Making a Second Call While Current Call in Progress To make a second call while you are currently on a call, press the “Voice Recognition” button and say ⬙Dial⬙ or ⬙Call⬙ followed by the phone number or phonebook entry you wish to call. The first call will be on hold while the second call is in progress. To go back to the first call, refer to ⬙Toggling Between Calls⬙ in this section. To combine two calls, refer to ⬙Conference Call⬙ in this section.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 Call Termination To end a call in progress, momentarily press the PHONE button. Only the active call(s) will be terminated and if there is a call on hold, it will become the new active call. If the active call is terminated by the far end, a call on hold may not become active automatically. This is cell phone-dependent. To bring the call back from hold, press and hold the PHONE button until you hear a single beep. Redial • Press the PHONE button to begin.
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE UConnect姞 System Features Language Selection To change the language that the UConnect威 system is using: • Press the PHONE button to begin. • After the ⬙Ready⬙ prompt and the following beep, say the name of the language you wish to switch to English, Espanol, or Francais. • Continue to follow the system prompts to complete language selection. After selecting one of the languages, all prompts and voice commands will be in that language.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 Canada and 060 for Mexico). The number dialed may not be applicable with the available cellular service and area. • If supported, this number may be programmable on some systems. To do this, press ‘Phone’ button and say ‘Setup’, followed by ‘Emergency’. • The UConnect威 system does slightly lower your chances of successfully making a phone call as to that for the cell phone directly.
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE certain companies, which time out a little too soon to work properly with the UConnect威 system. Voice Mail Calling To learn how to access your voice mail, refer to ⬙Working with Automated Systems.⬙ Working with Automated Systems This method is used in instances where one generally has to press numbers on the cellular phone keypad while navigating through an automated telephone system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 NOTE: • You may not hear all of the tones due to cellular phone network configurations; this is normal. • Some paging and voice mail systems have system time out settings that are too short and may not allow the use of this feature. Barge In - Overriding Prompts The “Voice Recognition” button can be used when you wish to skip part of a prompt and issue your voice recognition command immediately.
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE dialing a number with your paired Bluetooth威 cellular phone, the audio will be played through your vehicle’s audio system. The UConnect威 system will work the same as if you dial the number using voice recognition. NOTE: Certain brands of mobile phones do not send the dial ring to the UConnect威 system to play it on the vehicle audio system, so you will not hear it.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 Connect or Disconnect Link Between the UConnect威 System and Cellular Phone Your cellular phone can be paired with many different electronic devices, but can only be actively ⬙connected⬙ with one electronic device at a time. the lowest priority. To “select” or “delete” a paired phone being announced, press the “Voice Recognition” button and say “Select” or “Delete.” Also, see the next two sections for an alternate way to “select” or “delete” a paired phone.
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The selected phone will be used for the next phone call. If the selected phone is not available, the UConnect威 system will return to using the highest priority phone present in or near (approximately within 30 ft [9 m]) the vehicle. Delete UConnect威 Paired Cellular Phones • Press the PHONE button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Setup Phone Pairing.⬙ • At the next prompt, say ⬙Delete⬙ and follow the prompts.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 Repeat the words and phrases when prompted by the UConnect威 system. For best results, the Voice Training session should be completed when the vehicle is parked with the engine running, all windows closed, and the blower fan switched OFF. • Speak normally, without pausing, just as you would speak to a person sitting a few feet/meters away from you. This procedure may be repeated with a new user. The system will adapt to the last trained voice only.
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • When navigating through an automated system such as voice mail, or when sending a page, at the end of speaking the digit string, make sure to say ⬙Send.⬙ • Storing names in the phonebook when the vehicle is not in motion is recommended. • It is not recommended to store similar sounding names in the UConnect威 phonebook. • Phonebook (Downloaded and UConnect Local) name recognition rate is optimized when the entries are not similar.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 • Echo at the far end can sometimes be reduced by lowering the in-vehicle audio volume. • In a convertible vehicle, system performance may be compromised with the convertible top down. Bluetooth威 Communication Link Cellular phones have been found to lose connection to the UConnect威 system. When this happens, the connection can generally be re-established by switching the phone off/on. Your cell phone is recommended to remain in Bluetooth威 ON mode.
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 3
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 Primary zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location all Voice Commands Alternate(s) Voice Commands Primary Alternate(s) call cancel confirmation prompts continue delete dial download edit emergency English erase all Espanol Francais help home 3
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Primary language list names list phones mobile mute mute off new entry no pager pair a phone phone pairing phonebook previous record again redial Voice Commands Alternate(s) pairing phone book Voice Commands Primary Alternate(s) return to main menu return or main menu select phone select send set up phone settings or phone set up towing assistance transfer call UConnect威 Tutorial try again voice training work yes
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 General Information This device complies with Part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired operation.
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Manual Front And Second Row Seat Adjuster The adjusting bar is located under the front of the seat. Pull the bar upward and move the seat to the desired position. Release the bar to lock the seat into position. Using body pressure, move forward and rearward on the seat to be sure the seat adjusters have latched. WARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 Eight–Way Driver And Passenger Power Seat — If Equipped The power seat switches are located on the outboard side of the seat. The front switch controls the up/down, forward/rearward and tilt adjustment. The rear switch controls the recline adjustment of the seatback.
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! DO NOT place any article under a power seat or impede its ability to move as it may cause damage to the seat controls. Seat travel may become limited if movement is stopped by an obstruction in the seat’s path. Adjustable Head Restraints Head restraints can reduce the risk of whiplash injury in the event of impact from the rear. Pull upward or push downward on the head restraint cushion so that the upper edge is as high as practical.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 Heated Seats — If Equipped This feature heats the front driver and passenger seats. The controls for front heated seats are located on the center instrument panel area. The switch indicator lights will show when the High or Low heat is on. 3 Press the switch once to choose High (two lights), press it a second time to choose Low (one light), press it a third time to turn the heater Off (no lights).
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion or other physical condition must exercise care when using the seat heater. It may cause burns even at low temperatures, especially if used for long periods of time. DO NOT place anything on the seat that insulates against heat, such as a blanket or cushion.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 WARNING! DO NOT ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or fatally injured. Use the recliner only when the vehicle is parked. Manual Lumbar Adjust Lever — If Equipped The lumbar adjustment lever is located on the outboard side of the seat. To increase the support, rotate the lever downward.
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Fold Second Row Seats 1. Move the front seat fully forward. 2. Lower the head restraints and raise the armrests on the second row seat. 3. Slide the storage bin locking mechanism to the ⬙LOCK⬙ position and then pull up on the storage bin latch to open the cover. Storage Bin Cover Lock Release 4. Pull up on the seatback recliner lever located on the outboard side of the seat and fold the seatback down.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 3 Second Row Seatback Release Lever 5. Pull rearward on the release strap located at the rear of the seat and tumble the seat forward into the storage bin. Second Row Seat Release Strap 6. Close the storage bin cover.
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! 2. Pull up on the handle to lift the seat out of the storage bin and push the seat rearward to latch the seat anchors. The storage bin cover must be locked and flat to avoid damage from contact with the front seat tracks, which have minimal clearance to the cover. WARNING! In an accident, serious injury could result if the seat storage bin covers are not properly latched. • DO NOT drive the vehicle with the storage bin covers open.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 To tilt the seat, pull forward on the release strap located on the front of the seat between the seatback and seat cushion and tilt the seat fully forward. To return the seat to its upright position, push rearward on the seatback until it latches. Always ensure that it is fully latched. Second Row Seatback Release Lever 4.
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Seats are removable In the event of a collision you could be injured if the seat is not fully latched. Swivel ’n Go Premium Seating — If Equipped Premium second row Swivel ’n Go Seating features include: • A table that installs between the second and third row seats.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 rotation. Once the seat begins to rotate, the handle may be released. The seat locks in position once reaching the forward or rearward positions only. WARNING! Failure to comply with the following conditions could result in serious injury or even death. • NEVER place any child seat or infant carrier in the Swivel ’n Go seat while it is in the rearward facing position.
156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! (Continued) • Occupants riding in Swivel ’n Go seating must be wearing their seat belt and the seat must be locked in either the forward-facing or rearward-facing position. • Make sure the Swivel ’n Go seat is in a locked position with the release handle fully engaged. Test the seat after it is locked to see that it doesn’t swivel. Removing Swivel ’n Go Premium Seating — If Equipped Release Bar 1.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 5. Lower the release handle located at the bottom front edge of the seat. Each seat weighs about 90 lbs (81 kg). Swivel ’n Go Premium Seating Table — If Equipped The Swivel ’n Go Seating Table consists of an easily assembled post and top. NOTE: Electrical contacts for the available heated seats automatically disengage or engage as the seat is removed or installed. The contacts slide past each other as the seat is rolled to and from the strikers.
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The table and leg are stored beneath the floor when not in use. To install the table follow these steps: 1. Open the floor storage cover in front of the second row seats. 3. Swivel the second row seats so they are facing the rear. 4. Insert pole into base by aligning the lock button into notch of the base. Installing Table Leg Into Base Table and Leg Storage 2. Remove the pole and table top by loosening the hook and loop straps.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 NOTE: You will hear an audible “click” when the lock button engages the base. 6. Place the table top over the installed pole aligning with the mating feature of the underside of the table top. Apply pressure on the table top and press downward. NOTE: You will hear an audible “click” when the table latch engages the pole. WARNING! Failure to comply with the following conditions could result in serious injury or even death.
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The table top should be removed from the leg prior to removing the leg from its mounting base. 4. Locate the release button on the pole. Press the release button firmly to activate the release from the base. 5. While pressing the release button, twist the pole in a counterclockwise rotation until it stops. Pull upward to remove the pole from the base. 6. Place the pole on the underside of the table top and secure with the hook and loop straps.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 Plastic Grocery Bag Retainer Hooks Retainer hooks which will hold plastic grocery bag handles are built into the seatbacks of all rear seats and some front seats. The floor supports the partial weight of the bagged goods. Second Row Bench Seat — If Equipped While the bench seat does not stow in the floor, it is removable for added cargo space. Release levers are located on the rear leg assemblies, near the floor.
162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! If not properly latched, the bench seats could become loose. Personal injuries could result. After reinstalling these seats, be sure the red indicator button on the release handles return into the handles. Third Row Power Seat — If Equipped The third row power seat offers the following features: • The seatbacks can be folded forward for additional cargo space if needed. • Head restraints can be stowed with the seat.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 3 One Touch Folding Seat Third Row The rear switch bank allows multiple power folding and unfolding positions for the third row seats. Left and right third row seats can be folded individually or together.
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE motion for a brief period. Should this occur, remove the obstacle and press the button again, for the desired position. To Fold Third Row Seats Manually — If Equipped 1. Lower the head restraint to its full down position. 2. Pull release strap marked “1” located on the rear of the seat to lower the seatback. 3. Pull release strap marked “2” to release the anchors. Folding Third Row Seat Strap 4.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 To Unfold Third Row Seats Tailgate Mode 1. Pull up on the assist strap to lift the seat out of the storage bin and push the seat forward until the anchors latch. 1. Pull release strap “2”, then pull release strap “3” to rotate the entire seat rearward. 3 2. Pull release strap marked “1” to unlock the recliner. 3. Pulling strap “3” releases the seatback to return to its full upright position. 4. Adjust the head restraint to the desired position.
166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! To avoid serious injury or death, NEVER operate the vehicle with occupants in the third row seat while in the tailgate mode. DRIVER MEMORY SEAT SYSTEM — IF EQUIPPED Once programmed the Memory Buttons 1 and 2 on the driver’s door panel can be programmed to recall the driver’s seat, driver’s outside mirror, adjustable brake and accelerator pedals, and radio station preset settings.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 Setting Memory Positions And Linking RKE Transmitter To Memory 5. Turn on the radio and set the radio station presets (up to 10 AM and 10 FM stations can be set). NOTE: Each time the SET (S) button and a numbered button (1 or 2) is pressed, you erase the memory settings for that button and store a new one. 6. Turn the ignition switch to the OFF position and remove the key. 1. Insert the ignition key and turn the ignition switch to the ON position. 2.
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 11. Select ⬙Remote Linked to Memory⬙ in the Electronic Vehicle Information Center (EVIC). Refer to the “Customer-Programmable Features” in the “Electronic Vehicle Information Center (EVIC)” section for more information. To recall the memory setting for driver two, press Memory button 2 on the driver’s door or the UNLOCK button on the RKE transmitter linked to Memory Position 2. 12.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 3. Press and release the memory SET (S) button located on the driver’s door. A chime will sound signaling that you are in the memory set mode. Refer to the Remote Linked to Memory ⬙CustomerProgrammable Features⬙ in the Electronic Vehicle Information Center (EVIC) for more information. 4. Within five seconds, press and release Memory button 1 on the driver’s door. A chime will sound signaling to you that the driver memory has been set.
170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • When you remove the key from the ignition switch the driver seat will move to a position 0.3 in (7.7 mm) forward of the rear stop if the driver seat position is between 0.9 – 2.7 in (22.7 – 67.7 mm) forward of the rear stop. The seat will return to its previously set position when you insert the key into the ignition switch and turn it out of the LOCK position. • The Easy Entry/Easy Exit feature is disabled when the driver seat position is less than 0.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 3 Hood Release Lever Safety Lever Location 2. Move to the front of the vehicle and look inside the center of the hood opening. Locate, then push the safety catch lever to the right while raising the hood at the same time. Use the hood prop rod to secure the hood in the open position. To prevent possible damage, do not slam the hood to close it.
172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 12 in (30 cm) and then drop it. This should secure both latches. Never drive your vehicle unless the hood is fully closed, with both latches engaged. WARNING! If the hood is not fully latched, it could open when the vehicle is moving and block your forward vision. You could have a collision. Be sure all hood latches are fully latched before driving.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173 The interior lights will automatically turn off in approximately 10 minutes for the first activation and 90 seconds every activation thereafter until the engine is started, if one of the following occur: • A door, sliding door or the liftgate is left open Interior Lighting Defeat (Off) Rotate the dimmer control to the off position (extreme bottom). The interior lights will remain off when the doors or liftgate are open.
174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Dimmer Control With the parking lights or headlights on, rotating the dimmer control for the interior lights on the instrument panel upward will increase the brightness of the instrument panel lights. Halo Lights — If Equipped Halo lights are strategically placed soft lighting that help to illuminate specific areas to aid the occupants in locating specific features while driving at night. To activate the Halo lights, push in the Halo switch control knob.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175 will stay on for up to 90 seconds after you turn the ignition switch OFF. To turn the Automatic System off, turn the headlight switch clockwise to the “O” off position. Headlights On With Wipers — If Equipped When your headlights are in the Automatic mode and the engine is running, the headlights will automatically turn on when the wiper system is also turned on.
176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE When exiting the vehicle the driver can choose to have the headlights remain on for 30, 60, or 90 seconds or not remain on. To change the timer setting, see your authorized dealer. The headlight delay time is programmable on vehicles equipped with an EVIC. Refer to “Delay Turning Headlights Off,” under “Personal Settings (CustomerProgrammable Features)” under “Electronic Vehicle Information Center (EVIC)” in Section 4.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177 Front Fog Lights — If Equipped To activate the front fog lights, turn on the parking lights or the low beam headlights and push in the headlight switch control knob. Pressing the headlight switch control knob in a second time will turn the front fog lights off.
178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Turn Signals Move the multifunction lever up or down to signal either a right or left turn. If either indicator flashes at a rapid rate, check for a defective outside turn signal light bulb. If one of the indicators fails to light when the lever is moved, it would suggest that the indicator light is defective. You may manually signal a lane change by moving the lever partially up or down.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179 High Beam/Low Beam Select Switch When the headlights are turned on, pushing the multifunction lever toward the instrument panel will switch from Low beams to High beams. Pulling back to the neutral position returns the headlights to the Low beam operation. off position. If the windshield wiper switch is turned off and the blades cannot return to the off position, damage to the wiper motor may occur.
180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 1. Mist, Front Wiper and Washer Press the end of the multifunction lever inward to the first detent and release to clear the windshield. Pressing the multifunction lever inward to the second detent will cause the washers to spray for a maximum of 10 seconds, or until the multifunction lever is released, and the wipers will cycle three times.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181 3. Rear Wiper and Washer Rotating the rotary ring to the first detent activates the rear intermittent wipers. To activate the washers, rotate the rotary ring fully forward and the washers will spray until the ring is released, and then resume the intermittent interval. NOTE: Rear window wipers function in the intermittent wiper speed only. WARNING! Sudden loss of visibility through the windshield could lead to an accident.
182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE improved position with the steering wheel. The adjustable pedal system is designed to allow a greater range of driver comfort for steering wheel tilt and seat positions. The switch is located on the left side of the steering column.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 183 Press the button forward to move the pedals forward (toward the front of the vehicle). Press the button rearward to move the pedals rearward (toward the driver). • The pedals can be adjusted with the ignition OFF. • The pedals can be adjusted while driving. • The pedals cannot be adjusted when the vehicle is in REVERSE or when the Electronic Speed Control System is on.
184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE OFF button a second time, and both the Electronic Speed Control system and indicator will turn off. WARNING! Leaving the Electronic Speed Control system on when not in use is dangerous. You could accidently set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the Electronic Speed Control system off when you are not using it.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 185 Deactivating Electronic Speed Control A soft tap on the brake pedal or pulling the Electronic Speed Control lever (CANCEL) toward you will deactivate the Electronic Speed Control without erasing the set speed memory. Pushing the ON/OFF button to the OFF position or turning OFF the ignition erases the set speed memory. Resuming Speed To resume a previously set speed, raise the Electronic Speed Control lever (RESUME/ACCEL) upward, and release.
186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Speed Control system can be reactivated by pushing the Electronic Speed Control switch ON/OFF button and resetting the desired vehicle set speed. Accelerating To Pass Depress the accelerator as you normally would. When the pedal is released, the vehicle will return to the set speed. NOTE: The Electronic Speed Control system maintains speed up and down hills. A slight speed change on moderate hills is normal.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 187 The Rear Park Assist system will remember the last system state (enabled or disabled) from the last ignition cycle, when the ignition is changed to the RUN/ON position. The Rear Park Assist system can be active only when the shift lever is in REVERSE. When in REVERSE, the system scans for objects behind the vehicle, using four sensors located in the rear bumper.
188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE for about one second. Each side of the warning display has six yellow and two red LED lights, one set to warn of obstacles behind the left rear of the vehicle and the other set to warn of obstacles behind the right rear of the vehicle. The vehicle is close to the obstacle when the red LED is illuminated. The driver can view the LEDs either through the rearview mirror or by looking directly at the display above the rear window.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 189 WARNING DISPLAY DISTANCES DISPLAY INDICATOR OBSTACLE DISTANCE FROM: INDICATOR AUDIBLE SIGNAL COLOR REAR CORNERS REAR CENTER Inner LED 59 in (150 cm) Yellow Yes, Half Second 1st LED 51.2 in (130 cm) Yellow No 2nd LED 45.3 in (115 cm) Yellow No 3rd LED 31.5 in (80 cm) 39.3 in (100 cm) Yellow No 4th LED 25.5 in (65 cm) 33.5 in (85 cm) Yellow No 5th LED 20 in (50 cm) 27.6 in (70 cm) Yellow No 6th LED 16 in (40 cm) 19.
190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! WARNING! (Continued) • Drivers must be careful when backing up, even when using the Rear Park Assist System. Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, obstructions, or blind spots before backing up. You are responsible for the safety of your surroundings and must continue to pay attention while backing up. Failure to do so can result in serious injury or death.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 191 CAUTION! • To avoid vehicle damage, the Rear Park Assist system should only be used as a parking aid and is unable to recognize every obstacle, including small objects. Parking curbs might be temporarily detected or not detected at all. Obstacles located above or below the sensors will not be detected when they are in close proximity to the rear of the vehicle.
192 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Vehicles Equipped With the Compass Mini-Trip Computer (CMTC) You can turn the Rear Park Assist system ON or OFF through the CMTC by pressing the left reset button in the instrument cluster. Turn the ignition switch to the ON position, then press and hold the RESET button for approximately two seconds.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 193 NOTE: The Rear Camera system can be enabled and disabled, refer to your Radio/Navigation/Multimedia manual. Use the following steps to access the Rear Backup Camera feature: 1. Start the engine. 2. Place the shift lever into REVERSE. 3. Wait one to two seconds, and the camera view will display on the radio display screen. NOTE: The camera view will display only while the vehicle is in REVERSE. 4. Perform a thorough visual check of the rear area. 5.
194 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! • To avoid vehicle damage the Rear Backup Camera System should only be used as a parking aid and is unable to view every obstacle, or object in your drive path. • To avoid vehicle damage the vehicle must be driven slowly when using the Rear Backup Camera System to be able to stop in time when an obstacle is seen. It is recommended that the driver look frequently over his/her shoulder.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 195 when a front door, a sliding door or the liftgate is opened. If your vehicle is equipped with Remote Keyless Entry (RKE), the lights will also turn on when the UNLOCK button on the transmitter is pressed. The courtesy lights also function as reading lights. Press in on each lens to turn these lights on while inside the vehicle. Press a second time to turn each light off.
196 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Press the door latch to open the compartment. The door will slowly rotate to an open position. Rotating bin upward to partial open, positions lid for conversation mirror use. NOTE: The front overhead console supplied with factory sunroof, incorporates a sunroof switch. Rear Overhead Consoles — If Equipped The rear overhead storage system is available in two versions: with or without sunroof.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 197 Rear Courtesy/Reading Lights — If Equipped The overhead console has two sets of courtesy lights. The lights turn on when a front door, a sliding door or the liftgate is opened. If your vehicle is equipped with RKE, the lights will also turn on when the UNLOCK button on the RKE transmitter is pressed. The courtesy lights also function as reading lights. Press in on each lens to turn these lights on while inside the vehicle.
198 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! HomeLink威 Buttons NOTE: HomeLink威 is disabled when the Vehicle Security Alarm is active. • Your motorized door or gate will open and close while you are training the universal transceiver. Do not train the transceiver if people or pets are in the path of the door or gate. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by Federal safety standards.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 199 Programming Homelink姞 Before You Begin If you have not trained any of the HomeLink威 buttons, erase all channels before you begin training. To do this, press and hold the two outside buttons for up to 20 seconds until the red indicator flashes. It is recommended that a new battery be placed in the handheld transmitter of the device being programmed to HomeLink威 for more efficient training and accurate transmission of the radio-frequency signal.
200 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After training a HomeLink威 channel, if the garage door does not operate with HomeLink威 and the garage door opener was manufactured after 1995, the garage door opener may have a rolling code. If so, proceed to Step 5 “Programming A Rolling Code System.” This can usually be found where the hanging antenna wire is attached to the garage door opener motor. It is NOT the button normally used to open and close the door. 4.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 201 6. Firmly press and release the “Learn” or “Training” button. The name and color of the button may vary by manufacturer. NOTE: There are 30 seconds in which to initiate the next step after the “Learn” button has been pressed. 7. Return to the vehicle and press the programmed HomeLink威 button twice (holding the button for two seconds each time). If the device is plugged in and activates, programming is complete.
202 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Gate Operator/Canadian Programming Canadian radio frequency laws require transmitter signals to time-out (or quit) after several seconds of transmission – which may not be long enough for HomeLink威 to pick up the signal during programming. Similar to this Canadian law, some U.S. gate operators are designed to time-out in the same manner.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 203 Troubleshooting Tips If you are having trouble programming HomeLink威, here are some of the most common solutions: 2. This device must accept any interference that may be received including interference that may cause undesired operation. • Replace the battery in the original transmitter. • Did you unplug the device for training, and remember to plug it back in? NOTE: • The transmitter has been tested and it complies with FCC and IC rules.
204 UNDERSTANDING THE FEATURES OF YOUR VEHICLE POWER SUNROOF — IF EQUIPPED The power sunroof control switch is located in the front overhead console.The sunroof panel tilts upward at the rear for ventilation or slides rearward under the roof. Power Sunroof Operation Opening the Sunroof Manually Press the switch rearward and hold, and the sunroof will open automatically from any position. The sunroof will open fully, then stop automatically.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 205 NOTE: The sunshade cannot be closed if the sunroof is open. WARNING! Never leave children in a vehicle with the key in the ignition switch. Occupants, particularly unattended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death. Express-Open Press the switch rearward and release, and the sunroof will open automatically from any position.
206 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Ignition OFF Operation The power sunroof switch will remain active for 10 minutes after the ignition switch is turned OFF. Opening either front door will cancel this feature. Auto-Express with Anti–Pinch Protection During express closing, anytime an obstacle that restricts glass movement is detected, the motor will stop and reverse travel to avoid pinching the object. Auto Express will stop and reverse travel up to three times in succession.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 207 The lower outlet is protected by an automatic reset circuit breaker. The automatic circuit breaker restores power when the overload is removed. The circuit breaker also supplies power to the outlet in the removable floor console, when in the front position. Refer to Section 3, “Removable Floor Console” in this manual.
208 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! (Continued) • Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.), will degrade the battery even more quickly. Only use these intermittently and with greater caution. • After the use of high power draw accessories, or long periods of the vehicle not being started (with accessories still plugged in), the vehicle must be driven a sufficient length of time to allow the alternator to recharge the vehicle’s battery.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 209 The Power Inverter switch is located near the center of the instrument panel below the two 12-Volt power outlets. Press the switch to turn the power on for the outlet, press the switch a second time to turn the power off. CUPHOLDERS There are nine cupholders in the interior. Two cupholders in the center front instrument panel, four in the floor consoles and three more are located in the third row quarter trim panel. All liners are removable for cleaning.
210 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Interior Bottle Holders There are four bottle holders located in the interior. One bottle holder is molded into each front interior door trim panels, and one bottle holder is molded into each side sliding interior door trim panel. Each holder accommodates up to a 20 oz (1 L) plastic bottle. Two outboard mesh pockets are on intermediate seating. The mesh pockets are flexible enough to hold juice boxes, toys, games or MP3 players, etc.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 211 The left rear trim panel cupholder is designed to accommodate a second ash receiver, if desired. STORAGE Glove Compartments There are both upper and lower glove compartments. 3 Upper Glove Compartment To open the upper compartment, press in on the upper latch. The door will spring open about 1 in (2.54 cm). Manually lift the front edge of the door upward until fully opened and the detent is engaged.
212 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Lower Glove Compartment To open the lower compartment pull out on the release handle. NOTE: The lower compartment is equipped with a lock that is part of the compartment handle (2). Door Trim Panel Storage Front Door Storage Both interior front door panels have multiple pockets for storage.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 213 Sliding Side Door Bottle Holder Both sliding doors have a bottle holder molded right into the trim. Driver Seatback Storage — If Equipped The driver’s seatback has a primary storage pocket on all models and an optional secondary mesh pocket.
214 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Second Row Seat Storage Bins — If Equipped The seat storage bins are located on the floor in front of the second row seats. The area below the covers can be used for storage when the second row seat is in the upright position. Pull up on the storage bin latch to open the cover. Slide the storage bin locking mechanism to the ⬙Lock⬙ position to allow greater access to the storage bin.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 215 WARNING! In an accident, serious injury could result if the seat storage bin covers are not properly latched. • DO NOT drive the vehicle with the storage bin covers open. • Keep the storage bin covers closed and latched while the vehicle is in motion. • DO NOT use a storage bin latch as a tie down. 3 Rear Compartment Storage Bins Your vehicle is equipped with open storage areas located in each rear trim panel.
216 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Coat Hooks Coat hooks are located along the headliner for the second and third row seating positions. The coat hook load limit is 10 lbs (4.5 kg). Exceeding the recommended load limit can cause the coat hooks to break or disengage from the vehicle. Cargo Area Storage The liftgate sill plate has a raised line with the statement “Load To This Line”. This line indicates how far rearward cargo can be placed without interfering with liftgate closing.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 217 CONSOLE FEATURES There are two consoles available: Basic and Premium. Basic Console Basic Console features consist of the following: 3 • The basic console profile allows vehicle occupants to easily pass through the first row to the second. • Four cupholders accept up to extra large size beverage cups or 20 oz (.6 L) plastic bottles. Cupholders are dishwasher safe for cleaning. • The cupholders are removable to access a large storage bin.
218 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Slide the console base forward while lifting slightly to clear the rear load floor hook. 3. Remove the console. To Reinstall The Basic Floor Console 1. Position the console at a slight angle (front slightly higher than the rear). 2. Slide the console rearward into the floor bracket/ hook. 3. Align the console until the front anchor cup plug hole is centered on the winch hole. 4.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 219 • Large console center storage will store headphones for the available rear DVD entertainment system or other items • 12-Volt DC power outlet provides continuous power inside the console for cell phones or other electronics. 3 • Rear occupant accessible • Multiple adjustments • Removable from vehicle for additional floor space.
220 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The top and center console sections slide forward and rearward to provide added user comfort. A one-piece cup holder insert for both cavities can easily be removed for cleaning. The cupholders will also accommodate large size cups and 20 oz (.6 L) bottles. Position 1 shows the console closed with four cupholders and a convenient storage tray.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 221 Position 2 shows the raised storage tray revealing a large storage area below. easy access to the storage area below and provides two of the four cupholders for the second row passengers. 3 Console Position 2 Console Position 3 Dual Storage Bins Position 3 shows the top portion of the console in a rearward position. This is accomplished by lifting the upper most latch at the front of the console.
222 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Pull rearward to disengage from floor and remove console To reinstall the console: 1. Position the console at a slight angle (rear slightly higher than the front) 2. Slide the console forward into the floor bracket 3. Rotate the rear of the console down until it is resting on the floor bracket Console Position 4 To Remove The Premium Floor Console 1. Pull up on the bottom release handle in the front of the console 2.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 223 WARNING! In an accident, serious injury could result if the removable floor console is not properly installed. Always be sure the removable floor console is fully latched. ELECTRIC REAR WINDOW DEFROSTER — IF EQUIPPED Press the rear window defroster button (located on your front climate control) to turn on the rear window defroster and the optional heated mirrors. A light will illuminate to show that the defroster is on.
224 UNDERSTANDING THE FEATURES OF YOUR VEHICLE UMBRELLA HOLDER An umbrella holder has been conveniently molded into the left front door entry scuff molding. LOAD-LEVELING SYSTEM The automatic load-leveling system will provide a level riding vehicle under most passenger and cargo loading conditions. A hydraulic pump contained within the shock absorbers raises the rear of the vehicle to the correct height. It takes approximately 1 mile (1.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 225 WARNING! Do not install the load-leveling system on vehicles that are not equipped with Anti-Lock Brakes. Vehicles without Anti-Lock Brakes (ABS) have a heightsensing proportioning valve. Installing a leveling system will render this system ineffective, inappropriately reducing rear brake pressure, resulting in increased stopping distances. You could have a serious accident.
226 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The tie down holes on the crossbar ends should always be used to tie down the load. Check the straps frequently to be sure that the load remains securely attached. CAUTION! • Crossbars should remain equally spaced or parallel at any luggage rack position for proper function. Noncompliance could result in damage to the luggage rack, cargo and/or vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 227 WARNING! Cargo must be securely tied before driving your vehicle. Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage. Follow the Roof Rack Cautions when carrying cargo on your roof rack. SUN SCREENS — IF EQUIPPED Sun screens are available for second and third row seating windows.
228 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Sun Screen Attaching To Retainer Clips Sun Screen Extended Once the screen is completely to the top of the window, extend the top bar of the sun screen over the two hooks attached to the top of the window. To lower the sun screen, gently lift the tab upward to disengage the hooks, and feed the screen back into the base sill.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 Instrument Panel Features . . . . . . . . . . . . . . . . 233 ▫ Compass/Temperature Display . . . . . . . . . . . 250 䡵 Instrument Cluster – Base . . . . . . . . . . . . . . . . 234 䡵 Electronic Vehicle Information Center (EVIC) — If Equipped. . . . . . . . . . . . . . . . . . . . . . . . . . . 252 䡵 Instrument Cluster – Premium . . . . . . . . . . . . 235 䡵 Instrument Cluster Descriptions . . . . . . . . . . . .
230 UNDERSTANDING YOUR INSTRUMENT PANEL 䡵 AM/FM/CD/DVD Multimedia System Radio (RER/REN) – If Equipped . . . . . . . . . . . . . . . . 263 ▫ Operating Instructions — Voice Recognition System (VR) — If Equipped . . . . . . . . . . . . . 263 ▫ Operating Instructions — Hands-Free Communication (UConnect威) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 263 ▫ Clock Setting Procedure . . . . . . . . . . . . . . . . 263 䡵 Sales Code RES — AM/FM Stereo Radio With CD Player (MP3 AUX Jack). . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 231 ▫ Play Mode . . . . . . . . . . . . . . . . . . . . . . . . . 288 ▫ List Or Browse Mode . . . . . . . . . . . . . . . . . . 289 䡵 Satellite Radio — If Equipped (REN/REQ/RER/RES/REU Radios Only). . . . . 291 ▫ System Activation . . . . . . . . . . . . . . . . . . . . 292 ▫ Electronic Serial Number/Sirius Identification Number (ESN/SID) . . . . . . . . . 292 ▫ Selecting Satellite Mode . . . . . . . . . . . . . . . . 293 ▫ Satellite Antenna . . . . . . . . . . . . . . .
232 UNDERSTANDING YOUR INSTRUMENT PANEL 䡵 Climate Controls . . . . . . . . . . . . . . . . . . . . . . 301 ▫ Winter Operation . . . . . . . . . . . . . . . . . . . . . 319 ▫ Manual Heating, Ventilation And Air Conditioning (HVAC) System . . . . . . . . . . . . 301 ▫ Vacation/Storage . . . . . . . . . . . . . . . . . . . . . 319 ▫ Rear Manual Climate Control Zone — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 308 ▫ Automatic Temperature Control (ATC) — If Equipped . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 233 INSTRUMENT PANEL FEATURES 4 1 2 3 4 - Air Vent - Instrument Cluster - Shift Lever - Radio 5 6 7 8 - Storage Bin Upper Glove Compartment Lower Glove Compartment Climate Controls 9 - Storage or DVD 10 - Cup Holders 11 - Storage Bin 12 - Power Supply – 12V 13 14 15 16 - Hazard Switch Ignition Switch Dimmer Switch Headlight Switch
234 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER – BASE
UNDERSTANDING YOUR INSTRUMENT PANEL 235 INSTRUMENT CLUSTER – PREMIUM 4
236 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTIONS 1. Fuel Gauge The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON position. 2. Fuel Door Reminder The arrow in this symbol is a reminder that the Fuel Filler Door is located on the left side of the vehicle. 3. Temperature Gauge The temperature gauge shows engine coolant temperature. Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.
UNDERSTANDING YOUR INSTRUMENT PANEL 237 WARNING! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call an authorized dealer if your vehicle overheats. If you decide to look under the hood yourself, see Section 7 of this manual. Follow the warnings under the Cooling System Pressure Cap paragraph. 4. Speedometer Indicates vehicle speed. 5.
238 UNDERSTANDING YOUR INSTRUMENT PANEL If the ABS light is on, the brake system should be serviced as soon as possible to restore the benefits of Anti-Lock brakes. If the ABS light does not turn on when the Ignition switch is turned to the ON position, have the light inspected by an authorized dealer. 8. Brake System Warning Light This light monitors various brake functions, including brake fluid level and parking brake application.
UNDERSTANDING YOUR INSTRUMENT PANEL 239 If brake failure is indicated, immediate repair is necessary. WARNING! Driving a vehicle with the red brake light on is dangerous. Part of the brake system may have failed. It will take longer to stop the vehicle. You could have an accident. Have the vehicle checked immediately. Vehicles equipped with the Anti-Lock Brake System (ABS), are also equipped with Electronic Brake Force Distribution (EBD).
240 UNDERSTANDING YOUR INSTRUMENT PANEL 11. Odometer / Trip Odometer — If Equipped The odometer shows the total distance the vehicle has been driven. U.S. federal regulations require that upon transfer of vehicle ownership, the seller certify to the purchaser the correct mileage that the vehicle has been driven. Therefore, if the odometer reading is changed during repair or replacement, be sure to keep a record of the reading before and after the service so that the correct mileage can be determined.
UNDERSTANDING YOUR INSTRUMENT PANEL 241 NOTE: • If your vehicle is equipped with an hood switch, in the case of hood ajar, a warning message will be displayed in either the PRNDL/Odometer display as “hood” or “Hood Ajar” in the EVIC display. • Some of the above warnings will be displayed in the Compass Mini-Trip Computer / Electronic Vehicle Information Center Display Area located in the instrument cluster.
242 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: If the indicator message illuminates when you start the vehicle, the oil change indicator system did not reset. If necessary repeat this procedure. 13. Odometer Display Reset Button To reset a message display (gATE, gASCAP, noFUSE, CHAngE OIL, LoCOOL, LoWASH), push and hold the button until the display resets (approximately two seconds). 14.
UNDERSTANDING YOUR INSTRUMENT PANEL 243 16. Engine Temperature Warning Light This light warns of an overheated engine condition. As temperatures rise and the gauge approaches H , this indicator will illuminate and a single chime will sound after reaching a set threshold. Further overheating will cause the temperature gauge to pass H , the indicator will continuously flash and a continuous chime will occur until the engine is allowed to cool.
244 UNDERSTANDING YOUR INSTRUMENT PANEL 18. Oil Pressure Warning Light This light indicates low engine oil pressure. The light should turn on momentarily when the engine is started. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. A chime will sound for four minutes when this light turns on. Do not operate the vehicle until the cause is corrected. This light does not show how much oil is in the engine. The engine oil level must be checked under the hood.
UNDERSTANDING YOUR INSTRUMENT PANEL 245 23. Charging System Light This light shows the status of the electrical charging system. The light should come on when the ignition switch is first turned ON and remain on briefly as a bulb check. If the light stays on or comes on while driving, turn off some of the vehicle’s non-essential electrical devices or increase engine speed (if at idle). If the charging system light remains on, it means that the vehicle is experiencing a problem with the charging system.
246 UNDERSTANDING YOUR INSTRUMENT PANEL overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability. Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale.
UNDERSTANDING YOUR INSTRUMENT PANEL 247 CAUTION! The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equipment that is not of the same size, type, and/or style. Aftermarket wheels can cause sensor damage.
248 UNDERSTANDING YOUR INSTRUMENT PANEL 28. Compass Mini-Trip Computer (CMTC) Display / Electronic Vehicle Information Center (EVIC) Display— If Equipped CMTC Display — If Equipped On vehicles equipped with CMTC, the display provides the outside temperature, one of eight compass headings to indicate the direction the vehicle is facing and the current radio station. For more information refer to “Compass Mini-Trip Computer” in this section.
UNDERSTANDING YOUR INSTRUMENT PANEL 249 CMTC Odometer Display When the appropriate conditions exist, the following odometer messages will display: CHAngE OIL . . . . . . . . . . . . . . . Oil Change Required HOTOIL . . . . . Oil Temperature Exceeds Safe Threshold door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Door Ajar ESPOFF . . . . . . . . . . . . . . . . . . . . . . ESP Deactivated gATE . . . . . . . . . . . . . . . . . . . . . . . . . . . Liftgate Ajar gASCAP . . . . . . . . . . . . . .
250 UNDERSTANDING YOUR INSTRUMENT PANEL When the appropriate conditions exist, the following messages will display: cluster to switch from odometer, to trip A or trip B. Press and hold the right button, while the odometer/trip odometer is displayed, to reset. NE . . . . . . . Eight-point compass headings are displayed (N, S, E, W, NE, NW, SE, SW) 14°F. . . . . . . . . . . . Temperature (Fahrenheit or Celsius) AVG . . . . . . . . . Average Fuel Economy (U.S. or Metric) DTE . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 251 NOTE: Magnetic and battery powered devices, (such as cell phones, IPOD’s, radar detectors, PDA’s and laptops) should be kept away from the top of the instrument panel. This is where the compass module is located and such devices may interfere and cause false compass readings. To Set the Variance Start the engine and leave the transmission gear selector lever in the PARK position.
252 UNDERSTANDING YOUR INSTRUMENT PANEL 2. Press and hold the CMTC reset button (for approximately 10 seconds) until the current variance zone number is displayed. ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) — IF EQUIPPED 3. Release the CMTC reset button, then press and hold again for approximately 10 seconds, until the direction is displayed, with the CAL indicator on continuously in the display. 4.
UNDERSTANDING YOUR INSTRUMENT PANEL 253 This system conveniently allows the driver to select a variety of useful information by pressing the switches mounted on the steering wheel. The EVIC consists of the following: EVIC Menu / Step Control Button, as it appears on the left side of the steering column.
254 UNDERSTANDING YOUR INSTRUMENT PANEL Steering Wheel EVIC Compass/Temp Control Button, as it appears on the right side of the steering column. • Door(s) Ajar (with a single chime, if vehicle is in motion) • Liftgate Ajar (chime will sound when vehicle starts moving) • Hood Ajar (if equipped with hood switch) Press and release the Compass/Temperature button to for instant access to the Compass/ Temperature screens. Press this button to RESET Trip Functions and change Personal Settings.
UNDERSTANDING YOUR INSTRUMENT PANEL 255 • Right Rear Turn Signal Light Out • Park Assist Disabled • Service Park Assist System • Personal Settings Not Available — Vehicle Not in Park Oil Change Required Your vehicle is equipped with an engine oil change indicator system. The Oil Change Required message will flash in the EVIC display for approximately 10 seconds, after a single chime has sounded, to indicate the next scheduled oil change interval.
256 UNDERSTANDING YOUR INSTRUMENT PANEL The Trip Functions mode displays the following information. Average Fuel Economy Shows the average fuel economy since the last reset. When the fuel economy is reset, the display will read “RESET” or show dashes for two seconds. Then, the history information will be erased, and the averaging will continue from the last fuel average reading before the reset. Distance To Empty (DTE) Shows the estimated distance that can be traveled with the fuel remaining in the tank.
UNDERSTANDING YOUR INSTRUMENT PANEL 257 resettable functions, press and release the RESET button a second time, within three seconds of resetting the currently-displayed function (Reset ALL will display during this three-second window). Manual Compass Calibration If the compass appears erratic and the CAL indicator does not appear in the EVIC display, you must put the compass into the Calibration Mode manually, as follows: Compass Display The compass readings indicate the direction the vehicle is facing.
258 UNDERSTANDING YOUR INSTRUMENT PANEL Compass Variance Compass Variance is the difference between Magnetic North and Geographic North. To compensate for the differences, the variance should be set for the zone where the vehicle is driven, per the zone map. Once properly set, the compass will automatically compensate for the differences, and provide the most accurate compass heading. For the most accurate compass performance, the compass must be set using the following steps.
UNDERSTANDING YOUR INSTRUMENT PANEL 259 4. Press and release the STEP button until the proper variance zone is selected, according to the map. 5. Press and release the compass button to exit. Personal Settings (Customer-Programmable Features) Personal Settings allows you to set and recall features when the transmission is in PARK. If the transmission is out of PARK or the vehicle begins moving, a warning message PERSONAL SETTING NOT AVAILABLE , followed in three seconds by, VEHICLE NOT IN PARK.
260 UNDERSTANDING YOUR INSTRUMENT PANEL RKE Unlock When Driver Door 1st Press is selected, only the driver’s door will unlock on the first press of the Remote Keyless Entry (RKE) transmitter UNLOCK button. When Driver Door 1st Press is selected, you must press the RKE transmitter UNLOCK button twice, to unlock the passenger’s doors. When All Doors 1st Press is selected, all of the doors will unlock on the first press of the RKE transmitter UNLOCK button.
UNDERSTANDING YOUR INSTRUMENT PANEL 261 Easy Exit Seat This feature provides automatic driver seat positioning to enhance driver mobility when entering and exiting the vehicle. To make your selection, press and release the RESET button until YES (Y) or NO (N) appears. NOTE: The seat will return to the memorized seat location (if Recall Memory with Remote Key Unlock is set to ON) when the RKE transmitter is used to unlock the door.
262 UNDERSTANDING YOUR INSTRUMENT PANEL Park ASST. System When enable is selected, the Rear Park Assist System is activated. When disable is selected the system is deactivated and the instrument cluster will display the ⬙PARK ASSIST DISABLED⬙ message. To make your selection, press and release the RESET button until ENABLE or DISABLE appears. Display Units of Measure In The EVIC, odometer, and navigation system (if equipped) can be changed between English and Metric units of measure.
UNDERSTANDING YOUR INSTRUMENT PANEL 263 Rain Sensing Intermittent Wipers — If Equipped When ON is selected, the system will automatically activate the windshield wipers if it senses moisture on the windshield. To make your selection, press and release the RESET button until “ON” or “OFF” appears. When OFF is selected, the system reverts to the standard intermittent wiper operation.
264 UNDERSTANDING YOUR INSTRUMENT PANEL worldwide standard for time. This makes the system’s clock very accurate, once the appropriate time zone and daylight savings information is set. displayed. To move the minute backward, touch the screen where the word “Min” with the arrow pointing downward is displayed. To Manually Set the Clock — RER/REN 6. To save the new time setting, touch the screen where the word “Save” is displayed. 1. Turn on the multimedia system. 2.
UNDERSTANDING YOUR INSTRUMENT PANEL 265 Show Time if Radio is Off When selected, this feature will display the time of day on the touch screen when the multimedia system is turned off. Proceed as follows to change the current setting: 1. Turn on the multimedia system. 2. Touch the screen where the time is displayed. The clock setting menu will appear on the screen. 3. When this feature is on, a check mark will appear in the box next to the words “Show Time if Radio is Off.
266 UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE RES — AM/FM STEREO RADIO WITH CD PLAYER (MP3 AUX JACK) NOTE: The radio sales code is located on the lower right side of your radio faceplate. Operating Instructions — Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Control (Rotary) Push the On/Volume control knob to turn on the radio. Push the On/Volume control knob a second time to turn off the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL 267 to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations without stopping, until you release it. TIME Button Press the TIME button and the time of day will display. In AM or FM mode, pressing the TIME button will switch between the time and frequency displays. Clock Setting Procedure 1. Press and hold the TIME button, until the hours blink. 2.
268 UNDERSTANDING YOUR INSTRUMENT PANEL Push the rotary Tune/Scroll control knob a second time and MID will display. Turn the Tune/Scroll control knob to the right or left to increase or decrease the mid-range tones. Push the rotary Tune/Scroll control knob a third time and TREBLE will display. Turn the Tune/Scroll control knob to the right or left to increase or decrease the treble tones. Push the rotary Tune/Scroll control knob a fourth time and BALANCE will display.
UNDERSTANDING YOUR INSTRUMENT PANEL 269 and 12 FM stations to be stored into pushbutton memory. The stations stored in SET 2 memory can be selected by pressing the pushbutton twice. Every time a preset button is used, a corresponding button number will display. Buttons 1 - 6 These buttons tune the radio to the stations that you commit to pushbutton memory (12 AM and 12 FM stations). DISC Button Pressing the DISC button will allow you to switch from AM/FM modes to Disc modes.
270 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! • This CD player will accept 4-3/4 in (12 cm) discs only. The use of other sized discs may damage the CD player mechanism. • Do not use adhesive labels. These labels can peel away and jam the player mechanism. • RES is a single CD player. Do not attempt to insert a second CD if one is already loaded. • Dual-media disc types (one side is a DVD, the other side is a CD) should not be used, and they can cause damage to the player.
UNDERSTANDING YOUR INSTRUMENT PANEL 271 RW/FF Press the RW button to stop the CD at the beginning of the current CD track/title. Press and hold the FF (Fast Forward) button and the CD player will begin to fast forward until FF is released, or RW or another CD button is pressed. The RW (Reverse) button works in a similar manner. AM/FM Button Press the button to select either AM or FM mode. SET/RND Button (Random Play Button) Press this button while the CD is playing to activate Random Play.
272 UNDERSTANDING YOUR INSTRUMENT PANEL The radio uses the following limits for file systems: • Maximum number of folder levels: 8 • Maximum number of files: 255 • Maximum number of folders. (The radio display of file names and folder names is limited. For large numbers of files and/or folders, the radio may be unable to display the file name and folder name, and will assign a number instead. With a maximum number of files, exceeding 20 folders will result in this display.
UNDERSTANDING YOUR INSTRUMENT PANEL 273 rates (VBR) are also supported. The majority of MP3 files use a 44.1 kHz sampling rate and a 192, 160, 128, 96 or VBR bit rate. MPEG Specification MPEG-1 Audio Layer 3 MPEG-2 Audio Layer 3 Sampling Bit Rate (kbps) Frequency (kHz) 320, 256, 224, 192, 160, 128, 48, 44.1, 32 112, 96, 80, 64, 56, 48, 40, 32 160, 128, 144, 112, 96, 80, 64, 24, 22.
274 UNDERSTANDING YOUR INSTRUMENT PANEL Operation Instructions - Auxiliary Mode The auxiliary (AUX) jack is an audio input jack, which allows the user to plug in a portable device, such as an MP3 player, or cassette player, and utilize the vehicle’s audio system to amplify the source and play through the vehicle speakers. SALES CODE RES/RSC — AM/FM STEREO RADIO WITH CD PLAYER (MP3 AUX JACK) AND SIRIUS RADIO NOTE: The radio sales code is located on the lower right side of your radio faceplate.
UNDERSTANDING YOUR INSTRUMENT PANEL 275 Operating Instructions — Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Control (Rotary) Push the On/Volume control knob to turn on the radio. Push the On/Volume control knob a second time to turn off the radio. Electronic Volume Control The electronic volume control turns continuously (360 degrees) in either direction without stopping.
276 UNDERSTANDING YOUR INSTRUMENT PANEL Phone Button (UConnect威 Hands-Free Phone) — If Equipped Press this button to operate the Hands-Free Phone (UConnect威) feature (if equipped). Refer to “Hands-Free Communication (UConnect威)” in Section 3. If your vehicle is not equipped with or this feature is not available on your vehicle, a “Not Equipped With UConnect” message will display on the radio screen. TIME Button Press the TIME button and the time of day will display.
UNDERSTANDING YOUR INSTRUMENT PANEL 277 INFO Button Press the INFO button for an RDS station (one with call letters displayed). The radio will return a Radio Text message broadcast from an FM station (FM mode only). Push the rotary Tune/Scroll control knob a second time and MID will display. Turn the Tune/Scroll control knob to the right or left to increase or decrease the mid-range tones.
278 UNDERSTANDING YOUR INSTRUMENT PANEL MUSIC TYPE Button Pressing this button once will turn on the Music Type mode for five seconds. Pressing the MUSIC TYPE button or turning the Tune/Scroll control knob within five seconds will allow the program format type to be selected. Many radio stations do not currently broadcast Music Type information.
UNDERSTANDING YOUR INSTRUMENT PANEL 279 Program Type Sports Talk Top 40 Weather 16-Digit Character Display Sports Talk Top 40 Weather By pressing the SEEK button when the Music Type icon is displayed, the radio will be tuned to the next frequency station with the same selected Music Type name. The Music Type function only operates when in the FM mode.
280 UNDERSTANDING YOUR INSTRUMENT PANEL You may add a second station to each pushbutton by repeating the above procedure with this exception: Press the SET/RND button twice and SET 2 will show in the display window. Each button can be set for SET 1 and SET 2 in both AM and FM. This allows a total of 12 AM and 12 FM stations to be stored into pushbutton memory. The stations stored in SET 2 memory can be selected by pressing the pushbutton twice.
UNDERSTANDING YOUR INSTRUMENT PANEL 281 If you insert a disc with the ignition ON and the radio ON, the unit will switch from radio to CD mode and begin to play when you insert the disc. The display will show the disc number, the track number, and index time in minutes and seconds. Play will begin at the start of track 1. CAUTION! • This CD player will accept 4–3/4 in (12 cm) discs only. The use of other sized discs may damage the CD player mechanism. • Do not use adhesive labels.
282 UNDERSTANDING YOUR INSTRUMENT PANEL the current selection. Pressing and holding the SEEK button will allow faster scrolling through the tracks in CD, MP3 modes. TIME Button Press this button to change the display from a large CD playing time display to a small CD playing time display. RW/FF Press the RW button to stop the CD at the beginning of the current CD track/title.
UNDERSTANDING YOUR INSTRUMENT PANEL 283 Supported Medium Formats (File Systems) The medium formats supported by the radio are ISO 9660 Level 1 and Level 2 and includes the Joliet extension. When reading discs recorded using formats other than ISO 9660 Level 1 and Level 2, the radio may fail to read files properly and may be unable to play the file normally. UDF and Apple HFS formats are not supported.
284 UNDERSTANDING YOUR INSTRUMENT PANEL Supported MP3 File Formats The radio will recognize only files with the *.MP3 extension as MP3 files. Non-MP3 files named with the *.MP3 extension may cause playback problems. The radio is designed to recognize the file as an invalid MP3 and will not play the file. When using the MP3 encoder to compress audio data to an MP3 file, the bit rate and sampling frequencies in the following table are supported. In addition, variable bit rates (VBR) are also supported.
UNDERSTANDING YOUR INSTRUMENT PANEL 285 Loading times for playback of MP3 files may be affected by the following: • Media - CD-RW media may take longer to load than CD-R media • Medium formats - Multisession discs may take longer to load than non-multisession discs • Number of files and folders - Loading times will increase with more files and folders To increase the speed of disc loading, it is recommended to use CD-R media and single-session discs.
286 UNDERSTANDING YOUR INSTRUMENT PANEL Operation Instructions - Auxiliary Mode The auxiliary (AUX) jack is an audio input jack, which allows the user to plug in a portable device such as an MP3 player, or cassette player, and utilize the vehicle’s audio system to amplify the source and play through the vehicle speakers. Pressing the AUX button will change the mode to auxiliary device if the AUX jack is connected. NOTE: The AUX device must be turned on and the device’s volume set to proper level.
UNDERSTANDING YOUR INSTRUMENT PANEL 287 UCI supports Mini, 4G, Photo, Nano, 5G iPod威 and iPhone威 devices. Some iPod威 software versions may not fully support the UCI features. Please visit Apple’s website for software updates. NOTE: • If the radio has a USB port, connecting an iPod威 to this port does not play the media. For playing an iPod威, use the separate 16–pin connector port (in the glove compartment on some vehicles).
288 UNDERSTANDING YOUR INSTRUMENT PANEL • The iPod威 can be controlled using the radio buttons to Play, Browse, and List the iPod威 contents. • Turning it clockwise (forward) by one click, while playing a track, skips to the next track. • The iPod威 battery charges when plugged into the UCI connector. • Turning it counterclockwise (backward) by one click, during the first two seconds of the track, will jump to the previous track in the list.
UNDERSTANDING YOUR INSTRUMENT PANEL 289 • Use the << SEEK and SEEK >> buttons to jump to the previous or next track. If the << SEEK button is pressed during the first two seconds of the track, it will jump to the previous track in the list, if you press this button at any other time in the track it will jump to the beginning of the track. If you press the SEEK >> button during play mode, it will jump to the next track in the list.
290 UNDERSTANDING YOUR INSTRUMENT PANEL • Turning it clockwise (forward) and counterclockwise (backward) scrolls through the lists, displaying the track detail on the radio display. Once you have the track to be played highlighted on the radio display, press the TUNE control knob to select and start playing the track. Turning the TUNE control knob fast will scroll through the list faster. During fast scroll, you may notice a slight delay in updating the information on the radio display.
UNDERSTANDING YOUR INSTRUMENT PANEL 291 the same steps to go to the desired track in that list. Not all iPod威 sub-menu levels are available on this system. • MUSIC TYPE button: The MUSIC TYPE button is another shortcut button to the genre listing on your iPod威. CAUTION! • Leaving the iPod威 (or any supported device) anywhere in the vehicle in extreme heat or cold can alter the operation, or damage the device. Follow the device manufacturer’s guidelines.
292 UNDERSTANDING YOUR INSTRUMENT PANEL System Activation Sirius Satellite Radio service is pre-activated, and you may begin listening immediately to the one year of audio service that is included with the factory-installed satellite radio system in your vehicle. Sirius will supply a welcome kit that contains general information, including how to setup your on-line listening account at no additional charge.
UNDERSTANDING YOUR INSTRUMENT PANEL 293 Next, turn the knob surrounding the joystick in the center of the radio to scroll to Subscription, and then press and release the joystick. All of the ESNs that apply to your vehicle will display. Selecting Satellite Mode Press the SAT button until ⬙SAT⬙ appears in the display. A CD may remain in the radio while in the Satellite radio mode.
294 UNDERSTANDING YOUR INSTRUMENT PANEL SEEK Buttons Press and release the SEEK buttons to search for the next channel in Satellite mode. Press the right switch to seek up and the left switch to seek down. The radio will remain tuned to the new channel until you make another selection. Holding either button will bypass channels without stopping until you release it.
UNDERSTANDING YOUR INSTRUMENT PANEL 295 MUSIC TYPE Button — Except REU Radio Pressing this button once will turn on the Music Type mode for five seconds. Pressing the MUSIC TYPE button or turning the Tune/Scroll control knob within five seconds will allow the program format type to be selected. Toggle the MUSIC TYPE button again to select the music type. By pressing the SEEK button when the Music Type function is active, the radio will be tuned to the next channel with the same selected Music Type name.
296 UNDERSTANDING YOUR INSTRUMENT PANEL SET Button – To Set the Pushbutton Memory When you are receiving a channel that you wish to commit to pushbutton memory, press the SET button. The symbol SET 1 will now show in the display window. Select the button (1-6) you wish to lock onto this channel and press and release that button. If a button is not selected within five seconds after pressing the SET button, the channel will continue to play but will not be stored into pushbutton memory.
UNDERSTANDING YOUR INSTRUMENT PANEL 297 SIRIUS BACKSEAT TV™ — IF EQUIPPED Satellite video uses direct satellite receiver broadcasting technology to provide streaming video. The subscription service provider is SIRIUS Satellite Radio. SIRIUS Backseat TV™ offers three video channels for family entertainment, directly from its satellites and broadcasting studios. NOTE: SIRIUS service is not available in Hawaii and has limited coverage in Alaska.
298 UNDERSTANDING YOUR INSTRUMENT PANEL • Nine different medias to choose from in each screen (AM, FM, Sirius Radio, DVD1, DVD2, Hard Drive Jukebox, AUX in radio, AUX1, AUX2) The LCD screen(s) are located in the overhead compartment console. VES™ Remote Control Location NOTE: Refer to your VES™ User’s Manual for detailed operating instructions.
UNDERSTANDING YOUR INSTRUMENT PANEL 299 REMOTE SOUND SYSTEM CONTROLS — IF EQUIPPED system. Pressing the top of the rocker switch will increase the volume. Pressing the bottom of the rocker switch will decrease the volume. Pressing the center button changes the operation of the radio from AM to FM, or Tape to CD mode, depending on which radio is in the vehicle. The left-hand rocker switch has a pushbutton in the center. The function of the left-hand switch is different, depending on which mode you are in.
300 UNDERSTANDING YOUR INSTRUMENT PANEL CD Player Pressing the top of the switch once will go to the next track on the CD. Pressing the bottom of the switch once will go to the beginning of the current track, or to the beginning of the previous track if it is within one second after the current track begins to play. 3. Do not apply paper or tape to the disc; avoid scratching the disc. If you press the switch up or down twice it plays the second track; three times, it will play the third, etc. 6.
UNDERSTANDING YOUR INSTRUMENT PANEL 301 RADIO OPERATION AND CELLULAR PHONES Under certain conditions, the cellular phone being ON in your vehicle can cause erratic or noisy performance from your radio. This condition may be lessened or eliminated by relocating the cellular phone antenna. This condition is not harmful to the radio.
302 UNDERSTANDING YOUR INSTRUMENT PANEL Front Blower Control There are four blower speeds. Use this control to regulate the amount of air forced through the system in any mode you select. The blower speed increases as you move the control clockwise from the off position. NOTE: For vehicles equipped with Remote Start, the climate controls will not function during Remote Start operation if the blower control is left in the “O” (Off) position.
UNDERSTANDING YOUR INSTRUMENT PANEL 303 Temperature Control Use this control to regulate the temperature of the air inside the passenger compartment. Rotating the knob counterclockwise, from top center into the blue area of the scale, indicates cooler temperatures. Rotating the knob clockwise, into the red area, indicates warmer temperatures. Mode Control (Air Direction) Mode control allows you to choose from several patterns of air distribution.
304 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: There is a difference in temperature (in any conditions other than full cold or full hot), between the upper and lower outlets for added comfort. The warmer air goes to the floor outlets. This feature gives improved comfort during sunny but cool conditions. Defrost Mode Air is directed through the windshield and side window demist outlets. Use DEFROST mode with maximum blower and temperature settings for best windshield and side window defrosting.
UNDERSTANDING YOUR INSTRUMENT PANEL 305 Recirculation Control Press this button to choose between outside air intake or recirculation of the air inside the vehicle. A lamp will illuminate when you are in RECIRCULATION mode. Only use the RECIRCULATION mode to temporarily block out any outside odors, smoke, or dust, and to cool the interior rapidly upon initial start-up in very hot or humid weather.
306 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: For maximum airflow to the rear, the center instrument panel outlets can be directed toward the rear seat passengers. Economy Mode If ECONOMY mode is desired, press the A/C button to turn off the indicator light and the A/C compressor. Rotate the temperature control knob to the desired temperature. Air Conditioning Operation Push on this button to engage the Air Conditioning (A/C).
UNDERSTANDING YOUR INSTRUMENT PANEL 307 The Three-Zone Basic Temperature Control bottom panel controls rear Heating, Ventilation, and Air Conditioning (HVAC) operations.
308 UNDERSTANDING YOUR INSTRUMENT PANEL The primary control for the rear blower is on the front climate control unit located on the instrument panel. The Three-Zone Basic Temperature Control bottom panel has five positions; off, rear, and a range of blower speeds. Only when the primary control for the rear blower is in the rear (RR) position do the second row seat occupants have control of the rear blower speed.
UNDERSTANDING YOUR INSTRUMENT PANEL 309 Only when the front control for the rear blower is in the RR position do the second row seat occupants have control of the rear blower speed. The rear blower control, located in the rear overhead console, has an off position and a range of blower speeds. This allows the second row seat occupants to control the volume of air circulated in the rear of the vehicle.
310 UNDERSTANDING YOUR INSTRUMENT PANEL control is in FLOOR, DEFROST, or MIX modes, airflow will be directed out of the rear floor outlets. Automatic Temperature Control (ATC) — If Equipped Rear Mode Control • Front Three-Zone ATC allows both driver and front passenger seat occupant, and rear seat occupants to select individual comfort settings. Headliner Mode Air comes from the outlets in the headliner. Each of these outlets can be individually adjusted to direct the flow of air.
UNDERSTANDING YOUR INSTRUMENT PANEL 311 The Infrared Three-Zone ATC System automatically maintains the interior comfort level desired by the driver and all passengers. This is accomplished by an infrared sensor, located in the forward overhead console. Based on the sensor input, the system automatically adjusts the air temperature, the airflow volume, amount of outside air recirculation and the airflow direction. This maintains a comfortable temperature, even under changing conditions.
312 UNDERSTANDING YOUR INSTRUMENT PANEL Automatic Operation 1. Press the AUTO button on the Front Upper ATC Panel and the word AUTO will illuminate in the front ATC display, along with three temperatures for driver, front passenger, and rear seats. The system will then automatically regulate the amount of airflow. 2. Next, adjust the temperature you would like the system to maintain, by adjusting the driver, front passenger, and rear seat rotary temperature knobs.
UNDERSTANDING YOUR INSTRUMENT PANEL 313 NOTE: • It is not necessary to move the temperature settings for cold or hot vehicles. The system automatically adjusts the temperature, mode and fan speed to provide comfort as quickly as possible. Manual Operation This system offers a full complement of manual override features. The AUTO symbol in the front ATC display will be turned off when the system is being used in the manual mode. • The temperature can be displayed in U.S.
314 UNDERSTANDING YOUR INSTRUMENT PANEL Panel Mode Air comes from the outlets in the instrument panel. Each of these outlets can be individually adjusted to direct the flow of air. The air vanes of the center outlets and outboard outlets can be rotated to regulate or shut off the airflow from these outlets. Bi-Level Mode Air comes from the instrument panel outlets, floor outlets and defrost outlets. A slight amount of air is also directed through the side window demister outlets.
UNDERSTANDING YOUR INSTRUMENT PANEL 315 flows through the air outlets. If ECONOMY mode is desired, press the SNOWFLAKE button to turn off the SNOWFLAKE mode in the ATC display, and deactivate the A/C system. NOTE: • If the system is in Mix or Defrost Mode, the SNOWFLAKE can be turned off, but the A/C system shall remain active to prevent fogging of the windows. • If fog or mist appears on the windshield or side glass, select DEFROST mode and increase blower speed.
316 UNDERSTANDING YOUR INSTRUMENT PANEL Pressing the REAR LOCK button for the Rear ATC System from the front lower ATC panel, illuminates a LOCK symbol in the rear display. The rear temperature and air source are controlled from the front lower ATC panel. Rear second row occupants can only adjust the rear ATC control when the REAR LOCK button is turned off. The Rear ATC System is located in the headliner, near the center of the vehicle.
UNDERSTANDING YOUR INSTRUMENT PANEL 317 2. Rotate the Rear Blower, Rear Temperature and the Rear Mode Control knobs to suit your comfort needs. 3. ATC is selected by adjusting the rear blower knob counterclockwise to AUTO. Once the desired temperature is displayed, the ATC System will automatically achieve and maintain that comfort level. When the system is set up for your comfort level, it is not necessary to change the settings.
318 UNDERSTANDING YOUR INSTRUMENT PANEL Rear Temperature Control To change the temperature in the rear of the vehicle, rotate the temperature knob counterclockwise to lower the temperature, and clockwise to increase the temperature. The REAR temperature settings are displayed in the front upper ATC panel. When rear controls are locked by the front system, the LOCK symbol on the temperature knob is illuminated and any rear overhead adjustments are ignored.
UNDERSTANDING YOUR INSTRUMENT PANEL 319 to provide proper corrosion protection and to protect against engine overheating. A 50% solution of ethylene glycol antifreeze coolant in water is recommended. Refer to “Maintenance Procedures” in Section 7 of this manual for proper coolant selection. Winter Operation To ensure the best possible heater and defroster performance, make sure the engine cooling system is functioning properly and the proper amount, type, and concentration of coolant is used.
320 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Tips A/C Air Filter— If Equipped On vehicles equipped with Automatic Temperature Control (ATC), the climate control system filters out dust and pollen from the air. Refer to “Air Conditioning” in Section 7 of this manual for filter replacement instructions.
STARTING AND OPERATING CONTENTS 䡵 Starting Procedures . . . . . . . . . . . . . . . . . . . . 324 ▫ Acceleration . . . . . . . . . . . . . . . . . . . . . . . . 334 ▫ Automatic Transaxle . . . . . . . . . . . . . . . . . . 324 ▫ Traction . . . . . . . . . . . . . . . . . . . . . . . . . . . 335 䡵 Engine Block Heater — If Equipped . . . . . . . . . 327 䡵 Driving Through Water . . . . . . . . . . . . . . . . . . 335 䡵 Automatic Transaxle . . . . . . . . . . . . . . . . . . . .
322 STARTING AND OPERATING 䡵 Anti-Lock Brake System (ABS) . . . . . . . . . . . . 341 ▫ Tire Pressure . . . . . . . . . . . . . . . . . . . . . . . . 358 ▫ Anti-Lock Brake Light . . . . . . . . . . . . . . . . . 343 䡵 Tire Chains . . . . . . . . . . . . . . . . . . . . . . . . . . 367 䡵 Brake System . . . . . . . . . . . . . . . . . . . . . . . . . 343 䡵 Snow Tires . . . . . . . . . . . . . . . . . . . . . . . . . . 368 䡵 Electronic Brake Control System . . . . . . . . . . . 344 䡵 Tire Rotation . .
STARTING AND OPERATING 323 ▫ MMT In Gasoline . . . . . . . . . . . . . . . . . . . . 381 ▫ Replacement Parts . . . . . . . . . . . . . . . . . . . . 386 ▫ Materials Added To Fuel . . . . . . . . . . . . . . . 381 ▫ Maintenance . . . . . . . . . . . . . . . . . . . . . . . . 387 ▫ Fuel System Cautions . . . . . . . . . . . . . . . . . . 382 䡵 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . 387 ▫ Carbon Monoxide Warnings . . . . . . . . . . . . . 382 ▫ Fuel Filler Cap (Gas Cap) . . . . .
324 STARTING AND OPERATING STARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust the inside and outside mirrors, fasten your seat belt, and if present, instruct all other occupants to buckle their seat belts. WARNING! • Never leave unattended children alone in a vehicle. Leaving children in a vehicle is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Do not leave the key in the ignition.
STARTING AND OPERATING 325 2. Use the Fob with Integrated Key to briefly turn the ignition switch to the START position and release it as soon as the starter engages. The starter motor will continue to run, and it will disengage automatically when the engine is running. 3. If the engine fails to start, the starter will disengage automatically in 10 seconds. If this occurs, turn the ignition switch to the LOCK position, wait 10 to 15 seconds, then repeat the normal starting procedure (Steps 1–3 above).
326 STARTING AND OPERATING WARNING! (Continued) • Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transaxle cannot be started this way. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle. • If the vehicle has a discharged battery, booster cables may be used to obtain a start from a booster battery or the battery in another vehicle.
STARTING AND OPERATING 327 After Starting The idle speed will automatically decrease as the engine warms up. ENGINE BLOCK HEATER — IF EQUIPPED The engine block heater warms engine coolant and permits quicker starts in cold weather. Connect the electrical cord to a standard 110-115 Volt AC electrical outlet with a grounded, three-wire extension cord. The engine block heater cord is routed under the hood on the driver’s side of the vehicle.
328 STARTING AND OPERATING WARNING! It is dangerous to move the shift lever out of PARK or NEUTRAL if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in reverse. You could lose control of the vehicle and hit someone or something. Only shift into gear when the engine is idling normally and when your right foot is firmly on the brake pedal.
STARTING AND OPERATING 329 NOTE: If a malfunction occurs, the system will trap the key in the ignition cylinder to warn you that this safety feature is inoperable. The engine can be started and stopped but the key cannot be removed until you obtain service. Four-Speed or Six-Speed Automatic Transaxle NOTE: Under extreme cold temperatures (-6°F (-21°C) and when in DRIVE, transmission operation may be briefly limited to only 2nd gear operation.
330 STARTING AND OPERATING When parking on a flat surface, place the shift lever in the PARK position first, and then apply the parking brake. When parking on a hill, it is important to set the parking brake before placing the shift lever in PARK, otherwise the load on the transaxle locking mechanism may make it difficult to move the shift lever out of PARK. As an added precaution, turn the front wheels toward the curb on a downhill grade, and away from the curb on an uphill grade.
STARTING AND OPERATING 331 • Look at the shift indicator window on the console to ensure the shift lever is in the PARK position. • When engaged in PARK, you will not be able to move the shift lever rearward without depressing the shift lever button. CAUTION! Before moving the shift lever out of PARK, you must turn the ignition from LOCK/OFF to ON so the steering wheel and shift lever are released. Otherwise, damage to the steering column or shift lever could result.
332 STARTING AND OPERATING operating the vehicle under heavy loading conditions, (i.e., in hilly terrain, traveling into strong head winds or while towing heavy trailers). Under these conditions, using the “5” range will improve performance and extend transaxle life by reducing excessive shifting and heat buildup. DRIVE — Four-Speed Transaxle This range should be used for most city and highway driving. It provides the smoothest upshifts, downshifts, and best fuel economy.
STARTING AND OPERATING 333 Switching from ERS to DRIVE can be done at any vehicle speed. To shift from DRIVE mode to ERS mode, move the shift lever to the left (-) once. The current gear will be maintained as the top gear. To disable ERS, simply press and hold the shift lever to the right (+) until “D” is displayed in the instrument cluster odometer. WARNING! Do not downshift for additional engine braking on a slippery surface.
334 STARTING AND OPERATING Reset Mode - Electronic Transaxle The transaxle is monitored electronically for abnormal conditions. If a condition is detected that could cause damage, the transaxle automatically shifts into 2nd gear (3rd gear for six-speed). The transaxle remains in 2nd gear (3rd gear for six-speed) despite the forward gear selected. PARK, REVERSE, and NEUTRAL will continue to operate.
STARTING AND OPERATING 335 WARNING! Rapid acceleration on slippery surfaces is dangerous. Unequal traction can cause sudden pulling of the front wheels. You could lose control of the vehicle and possibly have an accident. Accelerate slowly and carefully whenever there is likely to be poor traction (ice, snow, wet mud, loose sand, etc.). Traction When driving on wet or slushy roads, it is possible for a wedge of water to build up between the tire and road surface.
336 STARTING AND OPERATING Flowing/Rising Water WARNING! Do not drive on, or cross, a road or a path where water is flowing and/or rising (as in storm run-off). Flowing water can wear away the road or path’s surface and cause your vehicle to sink into deeper water. Furthermore, flowing and/or rising water can carry your vehicle away swiftly. Failure to follow this warning may result in injuries that are serious or fatal to you, your passengers, and others around you.
STARTING AND OPERATING 337 CAUTION! (Continued) WARNING! • Driving through standing water may cause damage to your vehicle’s drivetrain components. Always inspect your vehicle’s fluids (i.e., engine oil, transmission/transaxle, axle, etc.) for signs of contamination (i.e., fluid that is milky or foamy in appearance) after driving through standing water. Do not continue to operate the vehicle if any fluid appears contaminated, as this may result in further damage.
338 STARTING AND OPERATING POWER STEERING The standard power steering system will give you good vehicle response and increased ease of maneuverability in tight spaces. The system will provide mechanical steering capability if power assist is lost. If for some reason the power assist is interrupted, it will still be possible to steer your vehicle. Under these conditions, you will observe a substantial increase in steering effort, especially at very low vehicle speeds and during parking maneuvers.
STARTING AND OPERATING 339 apparent, and/or the system is not functioning as anticipated. Coordinate inspection efforts through an authorized dealer. WARNING! Fluid level should be checked on a level surface and with the engine off to prevent injury from moving parts and to ensure accurate fluid level reading. Do not overfill. Use only manufacturers recommended power steering fluid. If necessary, add fluid to restore to the proper indicated level.
340 STARTING AND OPERATING WARNING! • Always fully apply the parking brake when leaving your vehicle, or it may roll and cause damage or injury. Also be certain to leave an automatic transaxle in PARK. Failure to do so may allow the vehicle to roll and cause damage or injury. • Be sure the parking brake is fully disengaged before driving. Failure to do so can lead to brake problems due to excessive heating of the rear brakes.
STARTING AND OPERATING 341 WARNING! NEVER leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Do not leave the key in the ignition. A child could operate power windows, other controls, or move the vehicle When parking on a hill, turn the front wheels toward the curb on a downhill grade, and away from the curb on an uphill grade.
342 STARTING AND OPERATING • A slight drop or fall away of the brake pedal at the end of the stop WARNING! • The Anti-Lock Brake System contains sophisticated electronic equipment that may be susceptible to interference caused by improperly installed, or high output radio transmitting equipment. This interference can cause possible loss of anti-lock braking capability. Installation of such equipment should be performed by qualified professionals.
STARTING AND OPERATING 343 Anti-Lock Brake Light The ABS light monitors the Anti-Lock Brake System. The light will come on when the ignition switch is turned to the ON position and may stay on for as long as four seconds. If both the Brake Warning Light and the ABS Light remain on, the ABS and Electronic Brake Force Distribution (EBD) systems are not functioning. Immediate repair to the ABS system is required. Consult with your authorized dealer service center as soon as possible.
344 STARTING AND OPERATING In the event power assist is lost for any reason (for example, repeated brake applications with the engine off), the brakes will still function. The effort required to brake the vehicle will be much greater than that required with the power system operating. WARNING! • Riding the brakes can lead to brake failure and possibly an accident.
STARTING AND OPERATING 345 Traction Control System (TCS) This system monitors the amount of wheel spin of each of the driven wheels. If wheel spin is detected, brake pressure is applied to the slipping wheel(s) and engine power is reduced, to provide enhanced acceleration and stability. A feature of the TCS functions similarly to a limited-slip differential, and controls the wheel spin across a driven axle.
346 STARTING AND OPERATING Brake Assist System (BAS) The BAS is designed to optimize the vehicle’s braking capability during emergency braking maneuvers. The system detects an emergency braking situation by sensing the rate and amount of brake application, and then applies optimum pressure to the brakes. This can help reduce braking distances. The BAS complements the ABS. Applying the brakes very quickly results in the best BAS assistance.
STARTING AND OPERATING 347 Electronic Stability Program (ESP) This system enhances directional control and stability of the vehicle under various driving conditions. ESP corrects for over/under steering of the vehicle by applying the brake of the appropriate wheel to assist in counteracting the over/under steer condition. Engine power may also be reduced to help the vehicle maintain the desired path.
348 STARTING AND OPERATING gain traction. To turn ESP on again, momentarily depress the ESP OFF switch. This will restore the normal ESP ON mode of operation. NOTE: To improve the vehicle’s traction when driving with snow chains, or starting off in deep snow, sand or gravel, it may be desirable to switch to the Partial OFF mode by pressing the ESP OFF switch. Once the situation requiring ESP to be switched to the Partial OFF mode is overcome, turn ESP back on by momentarily depressing the ESP OFF switch.
STARTING AND OPERATING 349 TIRE SAFETY INFORMATION Tire Markings NOTE: • P (Passenger) - Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designation. Example: P215/65R15 95H. • European-Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter ⬙P⬙ is absent from this tire size designation.
350 STARTING AND OPERATING Tires designed to this standard have the letter “T” molded into the sidewall preceding the size designation. Example: T145/80D18 103M. Tire Sizing Chart • High flotation tire sizing is based on U.S. design standards, and it begins with the tire diameter molded into the sidewall. Example: 31x10.5 R15 LT. EXAMPLE: Size Designation: P = Passenger Car tire size based on U.S. design standards ⴖ....blank....
STARTING AND OPERATING 351 EXAMPLE: R = Construction code — ⬙R⬙ means radial construction —⬙D⬙ means diagonal or bias construction 15 = Rim diameter in inches (in) Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions — The maximum speed corresponding to the speed symbol should only be achieved unde
352 STARTING AND OPERATING EXAMPLE: Load Identification: ⴖ....blank....
STARTING AND OPERATING 353 Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full TIN, including the date code, located on the white sidewall side of the tire. Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the outboard side, then you will find it on the inboard side of the tire.
354 STARTING AND OPERATING Tire Loading and Tire Pressure Tire and Loading Information Placard Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar.
STARTING AND OPERATING 355 3) tire size designed for your vehicle 4) cold tire inflation pressures for the front, rear, and spare tires. Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the Tire and Loading Information placard and in the “Vehicle Loading” section of this manual.
356 STARTING AND OPERATING available cargo and luggage load capacity is 650 lbs (295 kg) (since 5 x 150 = 750, and 1400 – 750 = 650 lbs [295 kg]). 5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4. 6. If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle.
STARTING AND OPERATING 357 5
358 STARTING AND OPERATING WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle. Three primary areas are affected by improper tire pressure.
STARTING AND OPERATING 359 WARNING! (Continued) • Unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • Always drive with each tire inflated to the recommended cold tire inflation pressure. Economy Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement.
360 STARTING AND OPERATING is defined as the tire pressure after the vehicle has not been driven for at least three hours, or driven less than 1 mile (1.6 km) after a three-hour period. The cold tire inflation pressure must not exceed the maximum inflation pressure molded into the tire sidewall. Check tire pressures more often if subject to a wide range of outdoor temperatures, as tire pressures vary with temperature changes.
STARTING AND OPERATING 361 WARNING! High-speed driving, with your vehicle at or above maximum load, is dangerous. The added strain on your tires could cause them to fail. You could have a serious accident. Do not drive a vehicle loaded to the maximum capacity at continuous speeds above 75 mph (120 km/h). Radial-Ply Tires WARNING! Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly. The instability could cause an accident.
362 STARTING AND OPERATING WARNING! (Continued) • Temporary-use spare tires have limited tread life. When the tread is worn to the tread wear indicators, the temporary use spare tire needs to be replaced. • Be sure to follow the warnings that apply to your spare. Failure to do so could result in spare tire failure and loss of vehicle control. Do not install a wheel cover or attempt to mount a conventional tire on the compact spare wheel, since the wheel is designed specifically for the compact spare.
STARTING AND OPERATING 363 WARNING! • The limited-use spare tire is for emergency use only. Installation of this limited-use spare tire affects vehicle handling. • Do not drive more than 50 mph (80 km/h) with a limited-use spare tire. • Keep the limited-use spare tire inflated to the cold tire inflation pressure, listed on either your tire placard or limited use spare tire and wheel assembly. • Replace (or repair) the original tire at the first opportunity and reinstall it on your vehicle.
364 STARTING AND OPERATING Tread Wear Indicators Tread wear indicators are in the original-equipment tires to help you in determining when your tires should be replaced. These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes 1/16 in (2 mm). When the tread is worn to the tread wear indicators, the tire should be replaced.
STARTING AND OPERATING 365 WARNING! The tires and the spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure. You could lose control and have an accident resulting in serious injury or death. Keep dismounted tires in a cool, dry place with as little exposure to light as possible. Protect tires from contact with oil, grease and gasoline.
366 STARTING AND OPERATING WARNING! WARNING! (Continued) • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle. This can cause unpredictable handling and stress to steering and suspension components. You could lose control and have an accident resulting in serious injury or death.
STARTING AND OPERATING 367 Tires may also cause the vehicle to pull to the left or right. Alignment will not correct this condition. See your authorized dealer for proper diagnosis. Improper alignment will not cause vehicle vibration. Vibration may be a result of tire and wheel out-ofbalance. Proper balancing will reduce vibration and avoid tire cupping and spotty wear. TIRE CHAINS Use only compact chains, or other traction aids that meet SAE type “Class S” specifications.
368 STARTING AND OPERATING CAUTION! (Continued) • Do not drive for prolonged periods of time on dry pavement. • Observe the tire chain manufacturer’s instructions on the method of installation, operating speed, and conditions for use. Always use the lower suggested operating speed of the chain manufacturer, if different from the speed recommended by the vehicle manufacturer. Always use the lower suggested operating speed if both the chain manufacturer and vehicle manufacture suggest a maximum speed.
STARTING AND OPERATING 369 TIRE ROTATION Tires on the front and rear axles of vehicles operate at different loads and perform different steering, driving, and braking functions. For these reasons, they wear at unequal rates, and tend to develop irregular wear patterns. These effects can be reduced by timely rotation of tires. The benefits of rotation are especially worthwhile with aggressive tread designs such as those on All-Season type tires.
370 STARTING AND OPERATING TIRE PRESSURE MONITOR SYSTEM (TPMS) The TPMS will warn the driver of a low tire pressure based on the cold inflation tire pressure requirements found on the tire placard located on the driver’s-side B-pillar. The tire pressure will vary with temperature by about 1 psi (6.9 kPa) for every 12°F (6.5°C). This means that when the outside temperature decreases, the tire pressure will decrease. Tire pressure should always be set based on cold inflation tire pressure.
STARTING AND OPERATING 371 For example, your vehicle may have a recommended cold (parked for more than three hours) tire pressure of 35 psi (241 kPa). If the ambient temperature is 68°F (20°C) and the measured tire pressure is 30 psi (207 kPa), a temperature drop to 20°F (-7°C) will decrease the tire pressure to approximately 26 psi (179 kPa). This tire pressure is sufficiently low enough to turn on the TPMS Warning Light.
372 STARTING AND OPERATING NOTE: • The TPMS is not intended to replace normal tire care and maintenance, or to provide warning of a tire failure or condition. • The TPMS should not be used as a tire pressure gauge while adjusting your tire pressure. • Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability.
STARTING AND OPERATING 373 The TPMS Telltale Warning Light will illuminate in the instrument cluster, and an audible chime will be activated when one or more of the four active road tire pressures are low. Should this occur, you should stop as soon as possible, check the inflation pressure of each tire on your vehicle, and inflate each tire to the vehicle’s recommended cold tire pressure value (located on the placard on the driver’s-side B-Pillar).
374 STARTING AND OPERATING NOTE: 1. The compact spare tire (if equipped) does not have a TPMS sensor. Therefore the TPMS will not monitor the pressure in the compact spare tire. 2. If you install the compact spare tire in place of a road tire that has a pressure below the low-pressure warning limit, upon the next ignition key cycle, a chime will sound and the TPMS Telltale Warning Light will turn on. 3.
STARTING AND OPERATING 375 • Three Trigger Modules (mounted in three of the four wheel wells) • Various TPMS messages, which display in the Electronic Vehicle Information Center (EVIC), and graphics displaying tire pressures • Yellow TPMS Telltale Warning Light TPMS Low Pressure Warnings The TPMS Telltale Warning Light will illuminate in the instrument cluster, and an audible chime will be activated when one or more of the four active road tire pressures are low.
376 STARTING AND OPERATING the TPMS Telltale Warning Light will extinguish once the updated tire pressure(s) have been received. The vehicle may need to be driven for up to 10 minutes above 15 mph (25 km/h) to receive this information. Check TPMS Message The TPMS Telltale Warning Light will flash on and off for 75 seconds, and remain on solid when a system fault is detected. The system fault will also sound a chime. The EVIC will display a CHECK TPM SYSTEM message for three seconds.
STARTING AND OPERATING 377 will not be present, and a pressure value will be displayed instead of dashes. A system fault can occur by any of the following scenarios: 1. Jamming due to electronic devices or driving next to facilities emitting the same radio frequencies as the TPMS sensors. 2. Installing some form of aftermarket window tinting that affects radio wave signals. 3. Accumulation of excessive snow and/or ice around the wheels or wheel housings. 4. Using tire chains on the vehicle. 5.
378 STARTING AND OPERATING 5. Once you repair or replace the original road tire, and reinstall it on the vehicle in place of the compact spare, the TPMS will update automatically. In addition, the TPMS Telltale Warning Light will turn off and the graphic in the EVIC will display a new pressure value instead of dashes (- -), as long no tire pressure is below the low pressure warning limit in any of the four active road tires.
STARTING AND OPERATING 379 4.0L Gasoline Engine This engine is designed to meet all emissions regulations and provide satisfactory fuel economy and performance when using high-quality unleaded gasoline having an octane range of 87 to 89. The manufacturer recommends the use of 89 octane for optimum performance. The use of premium gasoline is not recommended.
380 STARTING AND OPERATING The manufacturer supports the use of reformulated gasolines. Properly blended reformulated gasolines will provide excellent performance and durability of engine and fuel system components. Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with oxygenates such as 10% ethanol, MTBE, and ETBE. Oxygenates are required in some areas of the country during the winter months to reduce carbon monoxide emissions.
STARTING AND OPERATING 381 To fix a Non-FFV vehicle inadvertently fueled once with E-85 perform the following: • drain the fuel tank (see your authorized dealer) • change the engine oil and oil filter • disconnect and reconnect the battery to reset the engine controller memory More extensive repairs will be required for prolonged exposure to E-85 fuel. MMT In Gasoline MMT is a manganese containing metallic additive that is blended into some gasoline to increase octane.
382 STARTING AND OPERATING Fuel System Cautions CAUTION! Follow these guidelines to maintain your vehicle’s performance: • The use of leaded gas is prohibited by Federal law. Using leaded gasoline can impair engine performance and damage the emission control system. • An out-of-tune engine, or certain fuel or ignition malfunctions, can cause the catalytic converter to overheat.
STARTING AND OPERATING 383 WARNING! (Continued) • NEVER run the engine in a closed area, such as a garage, and NEVER sit in a parked vehicle with the engine running for an extended period. If the vehicle is stopped in an open area with the engine running for more than a short period, adjust the ventilation system to force fresh, outside air into the vehicle. • Guard against carbon monoxide with proper maintenance. Have the exhaust system inspected every time the vehicle is raised.
384 STARTING AND OPERATING E-85 Fuel Cap CAUTION! Only vehicles with the E-85 Decal and/or fuel filler door label can operate on E-85. E-85 Badge ETHANOL FUEL (E-85) E-85 is a mixture of approximately 85% fuel ethanol and 15% unleaded gasoline.
STARTING AND OPERATING 385 WARNING! Ethanol vapors are extremely flammable and could cause serious personal injury. Never have any smoking materials lit in or near the vehicle when removing the fuel filler tube cap (gas cap) or filling the tank. Do not use E-85 as a cleaning agent and never use it near an open flame. Fuel Requirements If your vehicle is E-85 compatible, it will operate on unleaded gasoline with an octane rating of 87, or E-85 fuel, or any mixture of these two fuels.
386 STARTING AND OPERATING increase in the time it takes for your engine to start and a deterioration in drivability (sags and/or hesitations) until the engine is fully warmed up. NOTE: Use of the engine block heater (if equipped) is beneficial for E-85 startability when the ambient temperature is less than 32°F (0°C). Selection Of Engine Oil For Flexible Fuel Vehicles (FFV) E-85 and Gasoline Vehicles FFV vehicles operated on E85 require specially formulated engine oils.
STARTING AND OPERATING 387 Maintenance If you operate the vehicle using E-85 fuel, follow the maintenance schedule section of this manual. NOTE: The driver’s side sliding door cannot be opened while the fuel door is open. This feature operates only when the sliding door is fully closed prior to opening the fuel door. CAUTION! Do not use ethanol mixture greater than 85% in your vehicle. It will cause difficulty in cold starting and may affect driveability.
388 STARTING AND OPERATING WARNING! WARNING! • Never have any smoking materials lit in or near the vehicle when the gas cap is removed or the tank filled. • Never add fuel when the engine is running. This is in violation of most state and federal fire regulations and will cause the malfunction indicator light to turn on. A fire may result if gasoline is pumped into a portable container that is inside of a vehicle. You could be burned. Always place gas containers on the ground while filling.
STARTING AND OPERATING 389 If the problem continues, the message will appear the next time the vehicle is started. See your authorized dealer as soon as possible. See Section 7 of this manual for more information. VEHICLE LOADING As required by National Highway Traffic Safety Administration regulations, your vehicle has a certification label affixed to the driver’s side door or B-Pillar.
390 STARTING AND OPERATING Gross Axle Weight Rating (GAWR) The GAWR is the maximum capacity of the front and rear axles. Distribute the load over the front and rear axles evenly. Make sure that you do not exceed either front or rear GAWR. WARNING! Because the front wheels drive and steer the vehicle, it is important that you do not exceed the maximum front or rear GAWR. A dangerous driving condition can result if either rating is exceeded. You could lose control of the vehicle and have an accident.
STARTING AND OPERATING 391 Overloading The load carrying components (axle, springs, tires, wheels, etc.) of your vehicle will provide satisfactory service as long as you do not exceed the GVWR and front and rear GAWR. The best way to figure out the total weight of your vehicle is to weigh it when it is fully loaded and ready for operation. Weigh it on a commercial scale to ensure that it is not over the GVWR. Figure out the weight on the front and rear of the vehicle separately.
392 STARTING AND OPERATING CAUTION! Do not load your vehicle any heavier than the GVWR or the maximum front and rear GAWR. If you do, parts on your vehicle can break, or it can change the way your vehicle handles. This could cause you to lose control. Also, overloading can shorten the life of your vehicle. A loaded vehicle is shown in the illustration. Note that neither the GVWR or the GAWR capacities have been exceeded.
STARTING AND OPERATING 393 LOADING TABLE — EXAMPLE ONLY Front Axle Rear Axle Empty Weight 2,140 lbs 1,470 lbs (971 kg) (667 kg) Load (Driver, 360 lbs 980 lbs passengers, and (163 kg) (445 kg) cargo/luggage) TOTAL 2,500 lbs 2,450 lbs (1 134 kg) (1 111 kg) GAWR 2,544 lbs 2,544 lbs (1 154 kg) (1 154 kg) A loaded vehicle is shown in the above table. Note that neither the GVWR nor the GAWR capacities have been exceeded.
394 STARTING AND OPERATING Gross Trailer Weight (GTW) The GTW is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or temporary) loaded in or on the trailer in its ⬙loaded and ready for operation⬙ condition. The recommended way to measure GTW is to put your fully loaded trailer on a vehicle scale. The entire weight of the trailer must be supported by the scale.
STARTING AND OPERATING 395 that typically provides adjustable friction associated with the telescoping motion to dampen any unwanted trailer swaying motions while traveling. Weight-Carrying Hitch A weight-carrying hitch supports the trailer tongue weight, just as if it were luggage located at a hitch ball or some other connecting point of the vehicle. This type of hitch is the most popular on the market today and is commonly used to tow small- and medium-sized trailers.
396 STARTING AND OPERATING Without Weight-Distributing Hitch (Incorrect) With Weight-Distributing Hitch (Correct)
STARTING AND OPERATING 397 The following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow, and should be used to assist you in selecting the correct trailer hitch for your intended towing condition. TRAILER HITCH CLASSIFICATIONS Max. GTW Class (Gross Trailer Wt.
398 STARTING AND OPERATING Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. GCWR (Gross Frontal Area Max. GTW (Gross Trailer Wt.) Max. Tongue Wt. Combined Wt. Rating) 7,000 lbs Up to 2 persons & Luggage 22 sq ft (2.0 sq m) 180 lbs (82 kg) (3 175 kg) 1,800 lbs (816 kg) 3.3L, 3.8L and 7,000 lbs 3 to 5 persons & Luggage 1,350 lbs 22 sq ft (2.0 sq m) 135 lbs (61 kg) (3 175 kg) (612 kg) 4.
STARTING AND OPERATING 399 Trailer and Trailer Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% to 15% of the Gross Trailer Weight (GTW) on the tow hitch of your vehicle. Loads balanced over the wheels or heavier in the rear can cause the trailer to sway severely side-to-side, which will cause loss of control of the vehicle and trailer. Failure to load trailers heavier in front is the cause of many trailer accidents.
400 STARTING AND OPERATING NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options, or authorized dealer-installed options, must be considered as part of the total load on your vehicle. Refer to the Tire and Loading Information placard in the “Tire-Safety Information” section of this manual for the maximum combined weight of occupants and cargo for your vehicle.
STARTING AND OPERATING 401 WARNING! (Continued) Make certain that the load is secured in the trailer and will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control. You could lose control of your vehicle and have an accident. • When hauling cargo or towing a trailer, do not overload your vehicle or trailer.
402 STARTING AND OPERATING Towing Requirements — Tires • Do not attempt to tow a trailer while using a compact spare tire. • Proper tire inflation pressures are essential to the safe and satisfactory operation of your vehicle. Refer to the “Tires–General Information” section for proper tire inflation procedures. • Also, check the trailer tires for proper tire inflation pressures before trailer usage. • Check for signs of tire wear or visible tire damage before towing a trailer.
STARTING AND OPERATING 403 • Trailer brakes are recommended for trailers over 1,000 lbs (454 kg) and required for trailers in excess of 2,000 lbs (907 kg). CAUTION! If the trailer weighs more than 1,000 lbs (454 kg) loaded, it should have its own brakes and they should be of adequate capacity. Failure to do this could lead to accelerated brake lining wear, higher brake pedal effort, and longer stopping distances. WARNING! • Do not connect trailer brakes to your vehicle’s hydraulic brake lines.
404 STARTING AND OPERATING The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. Refer to the following four-pin connector and seven-pin connector illustrations.
STARTING AND OPERATING 405 Towing Tips Before setting out on a trip, practice turning, stopping and backing the trailer in an area away from heavy traffic. Towing Tips — Automatic Transaxle The DRIVE gear can be selected when towing. However, if frequent shifting occurs while in DRIVE, move the gear selector lever into third gear (with four-speed transaxle) or fifth gear (with six-speed transaxle).
406 STARTING AND OPERATING The automatic transaxle fluid and filter should be changed if you REGULARLY tow a trailer for more than 45 minutes of continuous operation. Refer to the “Maintenance Schedule” in Section 8 of this manual for transaxle fluid change intervals. • Use speed control in flat terrain and with light loads to maximize fuel efficiency. NOTE: • Check the automatic transaxle fluid level before towing.
STARTING AND OPERATING 407 RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) NOTE: If the vehicle requires towing, make sure all four wheels are off the ground. CAUTION! Towing this vehicle behind another vehicle (flattowing with all four wheels on the ground) is not recommended.
WHAT TO DO IN EMERGENCIES CONTENTS 䡵 Hazard Warning Flasher . . . . . . . . . . . . . . . . . 410 䡵 Jump-Starting Procedure . . . . . . . . . . . . . . . . . 424 䡵 If Your Engine Overheats . . . . . . . . . . . . . . . . 410 䡵 Freeing A Stuck Vehicle . . . . . . . . . . . . . . . . . 427 䡵 Jacking And Tire Changing . . . . . . . . . . . . . . . 412 䡵 Towing A Disabled Vehicle . . . . . . . . . . . . . . . 427 ▫ Jack Location . . . . . . . . . . . . . . . . . . . . . . .
410 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER The Hazard Warning Flasher switch is located in the center of the instrument panel above the radio. Press the switch to turn on the Hazard Warning Flashers. When the Hazard Warning Flasher switch is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency. Press the switch a second time to turn off flashers. This is an emergency warning system and should not be used when the vehicle is in motion.
WHAT TO DO IN EMERGENCIES 411 the fan control to high. This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system. CAUTION! Driving with a hot cooling system could damage your vehicle. If temperature gauge reads “H”, pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the “H”, turn the engine off immediately, and call for service.
412 WHAT TO DO IN EMERGENCIES JACKING AND TIRE CHANGING WARNING! (Continued) WARNING! • Getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never get any part of your body under a vehicle that is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift. • The jack is designed to use as a tool for changing tires only.
WHAT TO DO IN EMERGENCIES 413 center of the vehicle by means of a cable winch mechanism. The “spare tire drive” nut is located on the floor, under a plastic cap at the front of the floor console. NOTE: The base console, if equipped, must be removed to raise and lower the spare tire. Refer to “Console Features” in Section 3 for the console removal procedure.
414 WHAT TO DO IN EMERGENCIES Preparations For Jacking 1. Park the vehicle on a firm level surface. Avoid ice or slippery areas. WARNING! Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid being hit when operating the jack or changing the wheel. 2. Set the parking brake.
WHAT TO DO IN EMERGENCIES 415 6. Block both the front and rear of the wheel diagonally opposite the jacking position. For example, if changing the right front tire, block the left rear wheel. NOTE: Passengers should not remain in the vehicle when the vehicle is being jacked.
416 WHAT TO DO IN EMERGENCIES WARNING! (Continued) • If working on or near a roadway, be extremely careful of motor traffic. • To assure that spare tires, flat or inflated are securely stowed, spares must be stowed with the valve stem facing the ground. • Turn on the Hazard Warning Flasher. 2. To remove the compact spare tire/cover assembly, assemble the winch handle extensions to form a “T’ and fit the winch “T” handle over the drive nut.
WHAT TO DO IN EMERGENCIES 417 WARNING! Getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never get any part of your body under a vehicle that is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift. NOTE: If either front tire is flat, it may be necessary to jack up the vehicle to remove the compact spare tire/ cover assembly from under the vehicle.
418 WHAT TO DO IN EMERGENCIES NOTE: • Rear jack locations are between a pair of down-facing tabs on the sill flange of the vehicle side body. • Front jack locations are on the sill flange of the vehicle side body, and align with front door edges. Squeezing Winch Retainer Tabs 5. There are two jack engagement locations on each side of the vehicle body. These locations are on the sill flange of the vehicle body.
WHAT TO DO IN EMERGENCIES 419 6 Jack Location
420 WHAT TO DO IN EMERGENCIES CAUTION! WARNING! Do not attempt to raise the vehicle by jacking on locations other than those indicated in Step 5. Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 6. Place the wrench on the jack screw and turn to the right until the jack head is properly engaged in the described location.
WHAT TO DO IN EMERGENCIES 421 10. Lower the vehicle by turning the jack screw to the left. 11. Finish tightening the lug nuts. Push down on the wrench while tightening for increased leverage. Alternate lug nuts until each nut has been tightened twice. Correct wheel nut tightness is 95 ft lbs (130 N·m). If in doubt about the correct tightness, have them checked with a torque wrench by your authorized dealer or at a service station. 12. Lower the jack to its fully-closed position.
422 WHAT TO DO IN EMERGENCIES of operation, and after each time a tire is changed, to allow the wheel nuts to become properly set. All nuts should first be firmly seated against the wheel. The nuts should then be tightened to recommended torque. Tighten the nuts to final torque in increments. Progress around the bolt circle, tightening the nut opposite to the nut just previously tightened until final torque is achieved. Recommended torque is 95 ft lbs (130 N·m). Secure The Spare Tire As Follows: 1.
WHAT TO DO IN EMERGENCIES 423 3. Turn the compact spare tire so that the valve stem is down, and place the tire into the spare tire/cover assembly. Slide the wheel spacer through the center of the wheel and spare tire/cover assembly, so that the two retainer tabs snap out and engage the spare tire cover on the opposite side. CAUTION! The compact spare tire/cover assembly must be used when the compact spare tire is stored.
424 WHAT TO DO IN EMERGENCIES CAUTION! WARNING! (Continued) For vehicles equipped with Stow ’n Go seating, the winch mechanism is designed specifically to stow a compact spare tire only. Do not attempt to use the winch to stow the full size flat tire, or any other full-size tire. Vehicle damage may result. JUMP-STARTING PROCEDURE WARNING! • Do not attempt to push or tow the vehicle to get it started. Vehicles equipped with an automatic transmission cannot be started this way.
WHAT TO DO IN EMERGENCIES 425 WARNING! (Continued) • Take special care to avoid the radiator cooling fan whenever the hood is raised. The cooling fan is electrically operated and can start anytime the ignition switch is ON. You can be hurt by the fan. • During cold weather when temperatures are below the freezing point, electrolyte in a discharged battery may freeze. Do not attempt jump-starting because the battery could rupture or explode.
426 WHAT TO DO IN EMERGENCIES 5. Connect the other cable, first to the negative terminal of the booster battery, and then to the engine of the vehicle with the discharged battery. Make sure there is a good contact on the engine. 7. When removing the jumper cables, reverse the above sequence exactly. Be careful of the moving belts and fan.
WHAT TO DO IN EMERGENCIES 427 FREEING A STUCK VEHICLE If your vehicle becomes stuck in mud, sand or snow, it can often be moved by a rocking motion. Turn your steering wheel right and left to clear the area around the front wheels. Then move the shift lever back and forth between REVERSE and DRIVE. Usually the least amount of accelerator pedal pressure to maintain the rocking motion without spinning the wheels is most effective. WARNING! Fast spinning tires can be dangerous.
428 WHAT TO DO IN EMERGENCIES • If the transmission is not operative, or if the vehicle is to be towed more than 100 miles (160 km), the vehicle must be towed with the front wheels off the ground. CAUTION! • Do not attempt to tow this vehicle from the front with sling-type towing equipment. Damage to the front fascia will result. • Always use wheel lift equipment when towing from the front. The only other approved method of towing is with a flatbed truck. • Do not tow the vehicle from the rear.
WHAT TO DO IN EMERGENCIES 429 Towing This Vehicle Behind Another Vehicle (Flat Towing With All Four Wheels On The Ground) Flat towing of vehicles equipped with an automatic transmission, is only permitted within the limitations described in this section. Towing This Vehicle Behind Another Vehicle With A Tow Dolly The manufacturer does not recommend that you tow a front wheel drive vehicle on a tow dolly. Vehicle damage may occur.
MAINTAINING YOUR VEHICLE CONTENTS 䡵 Engine Compartment — 3.3/3.8L . . . . . . . . . . 433 ▫ Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . 438 䡵 Engine Compartment — 4.0L . . . . . . . . . . . . . 434 ▫ Engine Oil Filter . . . . . . . . . . . . . . . . . . . . . 441 䡵 Onboard Diagnostic System — OBD II . . . . . . . 435 ▫ Engine Air Cleaner Filter . . . . . . . . . . . . . . . 441 ▫ Loose Fuel Filler Cap Message — Gascap . . . 435 ▫ Exhaust System . . . . . . . . . . . . . . . . . . . .
432 MAINTAINING YOUR VEHICLE ▫ Windshield Wiper Blades . . . . . . . . . . . . . . . 449 ▫ Headlights . . . . . . . . . . . . . . . . . . . . . . . . . 475 ▫ Cooling System . . . . . . . . . . . . . . . . . . . . . . 450 ▫ Front Park/Turn Signal Lights . . . . . . . . . . . 476 ▫ Brakes . . . . . . . . . . . . . . . . . . . . . . . . . . . . 456 ▫ Fog Lights . . . . . . . . . . . . . . . . . . . . . . . . . 476 ▫ Automatic Transaxle . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 433 ENGINE COMPARTMENT — 3.3/3.8L 7 1 2 3 4 5 6 — Air Cleaner Filter — Automatic Transmission Dipstick (3.
434 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT — 4.
MAINTAINING YOUR VEHICLE 435 ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
436 MAINTAINING YOUR VEHICLE filler cap message will be displayed in the instrument cluster. Tighten the gas cap until a ⬙clicking⬙ sound is heard. This is an indication that the gas cap is properly tightened. Press the odometer reset button to turn the message off. If the problem persists, the message will appear the next time the vehicle is started. If the problem is detected twice in a row, the system will turn on the Malfunction Indicator Light (MIL). Resolving the problem will turn the MIL light off.
MAINTAINING YOUR VEHICLE 437 4. As soon as you turn your key to the ON position, you will see the MIL symbol come on as part of a normal bulb check. 5. Approximately 15 seconds later, one of two things will happen: a. The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine. This means that your vehicle’s OBD II system is not ready and you should not proceed to the I/M station. b.
438 MAINTAINING YOUR VEHICLE DEALER SERVICE Your authorized dealer has the qualified service personnel, special tools, and equipment to perform all service operations in an expert manner. Service Manuals are available which include detailed service information for your vehicle. Refer to these manuals before attempting any procedure yourself. NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you.
MAINTAINING YOUR VEHICLE 439 The best time to check the engine oil level is about five minutes after a fully warmed engine is shut OFF or before starting the engine after it has sat overnight. Checking the oil while the vehicle is on level ground will improve the accuracy of the oil level readings. Maintain the oil level between the MIN and MAX markings on the dipstick. Adding one quart of oil when the reading is at the MIN mark will result in a MAX reading on these engines.
440 MAINTAINING YOUR VEHICLE American Petroleum Institute (API) Engine Oil Identification Symbol This symbol means that the oil has been certified by the American Petroleum Institute (API). The manufacturer only recommends API Certified engine oils. Engine Oil Viscosity (SAE Grade) — 3.3L & 3.8L Gasoline Engines SAE 5W-20 engine oil is recommended for all operating temperatures. This engine oil improves low temperature starting and vehicle fuel economy.
MAINTAINING YOUR VEHICLE 441 Synthetic Engine Oils You may use synthetic engine oils provided the recommended oil quality requirements are met, and the recommended maintenance intervals for oil and filter changes are followed. Materials Added to Engine Oil The manufacturer strongly recommends against the addition of any additives (other than leak detection dyes) to the engine oil. Engine oil is an engineered product and its performance may be impaired by supplemental additives.
442 MAINTAINING YOUR VEHICLE WARNING! The air induction system (air cleaner, hoses, etc.) can provide a measure of protection in the case of engine backfire. Do not remove the air induction system (air cleaner, hoses, etc.) unless such removal is necessary for repair or maintenance. Make sure that no one is near the engine compartment before starting the vehicle with the air induction system (air cleaner, hoses, etc.) removed. Failure to do so can result in serious personal injury.
MAINTAINING YOUR VEHICLE 443 WARNING! CAUTION! Exhaust gases can injure or kill. They contain carbon monoxide (CO) which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing CO, refer to “Exhaust Gas” in the Safety Tips section of this manual. Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition.
444 MAINTAINING YOUR VEHICLE WARNING! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your exhaust system. Do not park or operate your vehicle in areas where your exhaust system can contact anything that can burn. In unusual situations involving grossly malfunctioning engine operation, a scorching odor may indicate severe and abnormal catalyst overheating.
MAINTAINING YOUR VEHICLE 445 WARNING! CAUTION! • Battery fluid is a corrosive acid solution and can burn or even blind you. Do not allow battery fluid to contact your eyes, skin or clothing. Do not lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area immediately with large amounts of water. • Battery gas is flammable and explosive. Keep flame or sparks away from the battery.
446 MAINTAINING YOUR VEHICLE Air Conditioner Maintenance For best possible performance, your air conditioner should be checked and serviced by an authorized dealer at the start of each warm season. This service should include cleaning of the condenser fins and a system performance check. Drive belt tension should also be checked at this time. WARNING! • Use only refrigerants and compressor lubricants approved by the manufacturer for your air conditioning system.
MAINTAINING YOUR VEHICLE 447 A/C Air Filter — If Equipped Refer to the “Maintenance Schedule” in Section 8 for the proper maintenance intervals. WARNING! Do not remove the A/C air filter while the blower is operating or personal injury may result. The A/C air filter is located in the fresh air inlet behind the glove box. Perform the following procedure to replace the filter: 1. Open the glove compartment and remove all contents. 2. Push in on the sides of the glove compartment and lower the door. 3.
448 MAINTAINING YOUR VEHICLE CAUTION! The A/C air filter is labeled with an arrow to indicate airflow direction through the filter. Failure to properly install the filter will result in the need to replace it more often. 7. Rotate the glove compartment door back into position. Steering Shaft Seal The steering shaft seal, at the point where the shaft passes through the bulkhead, is lubricated when it is installed.
MAINTAINING YOUR VEHICLE 449 attention should also be given to hood latching components to insure proper function. When performing other underhood services, the hood latch, release mechanism and safety catch should be cleaned and lubricated. The external lock cylinders should be lubricated twice a year, preferably in the Fall and Spring. Apply a small amount of a high quality lubricant such as MOPAR威 Lock Cylinder Lubricant directly into the lock cylinder.
450 MAINTAINING YOUR VEHICLE WARNING! Commercially available windshield washer solvents are flammable. They could ignite and burn you. Care must be exercised when filling or working around the washer solution. After the engine has warmed, operate the defroster for a few minutes to reduce the possibility of smearing or freezing the fluid on the cold windshield.
MAINTAINING YOUR VEHICLE 451 Coolant Checks Check the engine coolant (antifreeze) protection every 12 months (before the onset of freezing weather, where applicable). If the engine coolant (antifreeze) is dirty or rusty in appearance, the system should be drained, flushed and refilled with fresh coolant. Check the front of the A/C condenser for any accumulation of bugs, leaves, etc. If dirty, clean by gently spraying water from a garden hose vertically down the face of the condenser.
452 MAINTAINING YOUR VEHICLE CAUTION! CAUTION! (Continued) • Mixing of engine coolant (antifreeze) other than specified Hybrid Organic Additive Technology (HOAT) engine coolant (antifreeze), may result in engine damage and may decrease corrosion protection. If a non-HOAT engine coolant (antifreeze) is introduced into the cooling system in an emergency, it should be replaced with the specified engine coolant (antifreeze) as soon as possible.
MAINTAINING YOUR VEHICLE 453 When adding engine coolant (antifreeze), a minimum solution of 50% recommended MOPAR威 Antifreeze/ Coolant Five Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology), or equivalent, in water should be used. Use higher concentrations (not to exceed 70%) if temperatures below ⫺34°F (⫺37°C ) are anticipated. Use only high purity water such as distilled or deionized water when mixing the water/engine coolant (antifreeze) solution.
454 MAINTAINING YOUR VEHICLE WARNING! • The warning words “DO NOT OPEN HOT” on the cooling system pressure cap are a safety precaution. Never add engine coolant (antifreeze) when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system. To prevent scalding or injury, do not remove the pressure cap while the system is hot or under pressure. • Do not use a pressure cap other than the one specified for your vehicle.
MAINTAINING YOUR VEHICLE 455 of this. As long as the engine operating temperature is satisfactory, the coolant bottle need only be checked once a month. When additional engine coolant (antifreeze) is needed to maintain the proper level, it should be added to the coolant bottle. Do not overfill. Points to Remember NOTE: When the vehicle is stopped after a few miles (a few kilometers) of operation, you may observe vapor coming from the front of the engine compartment.
456 MAINTAINING YOUR VEHICLE • Keep the front of the radiator clean. If your vehicle is equipped with air conditioning, also keep the front of the condenser clean also. • Do not change the thermostat for Summer or Winter operation. If replacement is ever necessary, install ONLY the correct type thermostat. Other designs may result in unsatisfactory coolant performance, poor gas mileage, and increased emissions.
MAINTAINING YOUR VEHICLE 457 Add enough fluid to bring the level up to the requirements described on the brake fluid reservoir. With disc brakes, fluid level can be expected to fall as the brake pads wear. However, low fluid level may be caused by a leak and a checkup may be needed. Use only manufacturer’s recommended brake fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in this section for the correct fluid type.
458 MAINTAINING YOUR VEHICLE Automatic Transaxle The automatic transaxle and differential assembly are contained within a single housing. The fluid level in the automatic transaxle should be checked whenever the vehicle is serviced. Operation with an improper fluid level will greatly reduce the life of the transaxle and the fluid. All four–speed transaxles are equipped with a conventional filler tube and dipstick. If fluid is added, it should be added through the filler tube.
MAINTAINING YOUR VEHICLE 459 Fluid Level Check — 3.8L and 4.0L Engines with Six-Speed Automatic Transaxle — If Equipped The six-speed automatic transaxle is a sealed unit and has no dipstick. See your authorized dealer to have the transaxle fluid checked or serviced. 1. The vehicle must be on level ground. Fluid Level Check — 3.3L Engine with Four-Speed Automatic Transaxle — If Equipped The dipstick is located just behind the radiator on the lower right side. 4.
460 MAINTAINING YOUR VEHICLE a. If the fluid is hot, the reading should be in the crosshatched area marked “HOT” (between the upper two holes in the dipstick). b. If the fluid is cold, the fluid level should be between the lower two holes in the area marked “COLD”. If the fluid level indicates that it is low, add sufficient fluid to bring it to the proper level. CAUTION! Do not overfill. Dirt and water in the transaxle can cause serious damage.
MAINTAINING YOUR VEHICLE 461 road surfaces on which the vehicle is operated, extreme hot or cold weather and other extreme conditions will have an adverse effect on paint, metal trim, and underbody protection. The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle. What Causes Corrosion? Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle.
462 MAINTAINING YOUR VEHICLE CAUTION! Do not use abrasive or strong cleaning materials such as steel wool or scouring powder, which will scratch metal and painted surfaces. Special Care • If you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month. • It is important that the drain holes in the lower edges of the doors and rocker panels be kept clear and open. • If you detect any stone chips or scratches in the paint, touch them up immediately.
MAINTAINING YOUR VEHICLE 463 a nonabrasive, non-acidic cleaner. Do not use scouring pads, steel wool, a bristle brush, or metal polishes. Only MOPAR威 or equivalent is recommended. Do not use oven cleaner. Avoid automatic car washes that use acidic solutions or harsh brushes that may damage the wheels’ protective finish. Interior Care Instrument Panel Surfaces The instrument panel cover has a low glare surface, which minimizes reflections in the windshield.
464 MAINTAINING YOUR VEHICLE WARNING! Do not use volatile solvents for cleaning purposes. Many are potentially flammable, and if used in closed areas they may cause respiratory harm. • For grease stains, apply MOPAR威 Multi-Purpose Cleaner to a clean, damp cloth and remove stain. Use a fresh, damp towel to remove soap residue. • Do not use any solvents or protectants on Yes Essentials威 products.
MAINTAINING YOUR VEHICLE 465 applique. Rub the applique with firm pressure then buff lightly with a clean cotton cloth until a high gloss shine is achieved. Cleaning Headlights Your vehicle has plastic headlights that are lightweight and less susceptible to stone breakage than glass headlights. Plastic is not as scratch resistant as glass and therefore different lens cleaning procedures must be followed.
466 MAINTAINING YOUR VEHICLE 1. Clean with a wet soft rag. A mild soap solution may be used, but do not use high alcohol content or abrasive cleaners. If soap is used, wipe clean with a clean damp rag. 2. Dry with a soft tissue. Seat Belt Maintenance Do not bleach, dye or clean the seat belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage can also weaken the fabric. If the seat belts need cleaning, use a mild soap solution or lukewarm water.
MAINTAINING YOUR VEHICLE 467 Installation Place the liner into the cupholder drawer and press the liner into place so that the retention tabs seat into the corresponding openings in the drawer. FUSES Totally Integrated Power Module (TIPM) The Totally Integrated Power Module (TIPM) is located in the engine compartment near the battery. Refer to the applicable “Engine Compartment” illustration in this section. This center contains cartridge fuses and minifuses.
468 MAINTAINING YOUR VEHICLE The numbers inside the TIPM cover correspond to the following table.
MAINTAINING YOUR VEHICLE 469 Cavity Cartridge Fuse FUSES/TIPM MiniFuse Description J18 20 Amp Yellow — J19 — — Front Wiper LO/HI — Front/Rear Washer — Sunroof Module M1 60 Amp Yellow 30 Amp Pink 20 Amp Yellow 25 Amp Natural — Powertrain Control Module (PCM) Trans Range Radiator Fan 15 Amp Blue M2 — M3 — 20 Amp Yellow 20 Amp Yellow Center High Mounted Stop Light (CHMSL)/ Brake Switch Trailer Lighting J20 J21 J22 — Cavity Cartridge Fuse M4 — M5 — M6 — M7 — M8 — M9 — FU
470 MAINTAINING YOUR VEHICLE Cavity Cartridge Fuse FUSES/TIPM MiniFuse M10 — 20 Amp Yellow M11 — 10 Amp Red M12 — 30 Amp Green Description Ignition Off Draw — Vehicle Entertainment System (IOD-VES), Satellite Digital Audio Receiver (SDARS), DVD, Hands-Free Module (HFM), Universal Garage Door Opener (UGDO), Vanity Lamp (VANITY LP) (Ignition Off Draw) IOD-HVAC/ATC, MW SENSR, Underhood Lamp (UH LMP) Amplifier (AMP) Cavity Cartridge Fuse FUSES/TIPM MiniFuse M13 — 20 Amp Yellow M14 — 20 Am
MAINTAINING YOUR VEHICLE 471 Cavity M15 Cartridge Fuse — FUSES/TIPM MiniFuse 20 Amp Yellow Description COL MOD, IR SNS, Heater Ventilation, Air Conditioning/ Automatic Temperature Control (HVAC/ ATC), Rear View Mirror (RR VW MIR), Cabin Compartment Node (CCN), Transfer Case Switch (T-CASE SW), RUN/ST, MultiFunction Control Switch (MULTIFTCN SW), Tire Pressure Monitor (TPM), Glow Plug Module (GLW PLG MOD) — Export Diesel Only Cavity Cartridge Fuse FUSES/TIPM MiniFuse M16 — 10 Amp Red M17 — 15 A
472 MAINTAINING YOUR VEHICLE Cavity Cartridge Fuse M21 — M22 — M23 — M24 — M25 — M26 — FUSES/TIPM MiniFuse 20 Amp Yellow 10 Amp Red 10 Amp Red 25 Amp Natural 20 Amp Yellow 10 Amp Red Description Auto Shut Down (ASD #3) Right Horn (RT HORN (HI/LOW) Left Horn (LT HORN (HI/LOW) Rear Wiper (REAR WIPER) Fuel Pump (FUEL PUMP), Diesel Lift Pump (DSL LIFT PUMP) — Export Only Power Mirror Switch (PWR MIRR SW), Driver Window Switch (DRVR WIND SW) Cavity Cartridge Fuse FUSES/TIPM MiniFuse M27 —
MAINTAINING YOUR VEHICLE 473 Cavity Cartridge Fuse FUSES/TIPM MiniFuse M33 — 10 Amp Red M34 — 10 Amp Red M35 — M36 — 10 Amp Red 20 Amp Yellow Description Next Generation Controller (NGC), Global Powertrain Engine Controller (GPEC) Park Assist (PRK ASST), Heater Ventilation, Air Conditioning Module (HVAC MOD), Headlamp Wash (HDLP WASH), Compass (COMPAS) Heated Mirrors Power Outlet #3 (BATT) Cavity Cartridge Fuse FUSES/TIPM MiniFuse M37 — 10 Amp Red M38 — 25 Amp Natural Description
474 MAINTAINING YOUR VEHICLE steering column. If you experience temporary or permanent loss of these systems, see your authorized dealer for service. VEHICLE STORAGE If you are leaving your vehicle dormant for more than 21 days, you may want to take steps to protect your battery. You may do the following: • Remove the 20 Amp mini-fuse in the Totally Integrated Power Module (TIPM) labeled Ignition-Off Draw (IOD). • Or, disconnect the negative cable from the battery.
MAINTAINING YOUR VEHICLE 475 LIGHT BULBS — Exterior Bulb Number Backup, Tail, Stop Light . . . . . . . . . . . . . . . . . . . 3157 Center High-Mounted Stop Light . . . LED (See Note 1) Fog Light — If Equipped . . . . . . . . . . . . . . . . . . 9145 Front Side Marker, Park/Turn Signal.. . . . . . . . . . . . . . . . . . . . . . . P27 / 7W or 3157 Headlight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H13 License . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
476 MAINTAINING YOUR VEHICLE 5. Connect the wiring connector to bulb and slide red lock tab forward. Front Park/Turn Signal Lights 1. Raise the hood to access the rear of the headlight housing. 2. Twist the turn signal socket and remove from the headlight housing, then pull the bulb out. 3. Push the new bulb into the socket and reinstall the socket by twisting until locked into the headlight housing. Fog Lights NOTE: Access to the fog light bulb is from the rear of the fascia.
MAINTAINING YOUR VEHICLE 477 Rear Tail, Stop, Turn Signal, Side Marker and Backup Lights 1. Raise the liftgate. 2. Remove the tail light assembly by removing the two screws from the inboard side. Use a fiber stick or similar tool to gently pry the light on the outboard side to disengage the two ball studs. Removing Tail Light Assembly NOTE: • If a screwdriver is used, make sure a soft material is placed between the vehicle body and tool so not to scratch the paint.
478 MAINTAINING YOUR VEHICLE Center High-Mounted Stop Light (CHMSL) The CHMSL uses LED lights that are not serviceable separately. The CHMSL must be replaced as an assembly. See your authorized dealer. License Light The light for the license plate light is located under the tailgate light bar and above the license plate. 1. Using a small screwdriver, press inward the locking tab on the outboard side of the light assembly and pull down on the light assembly for removal.
MAINTAINING YOUR VEHICLE 479 FLUIDS AND CAPACITIES Fuel (Approximate) Engine Oil with Filter 3.3L and 3.8L Engine (SAE 5W-20, API Certified) 4.0 Liter Engine (SAE 10W-30, API Certified) Cooling System * 3.3, 3.8, and 4.0 Liter Engine (MOPAR威 Engine Coolant/ Antifreeze 5 Year/100,000 Mile Formula) * Includes heater and coolant recovery bottle filled to MAX level. Add heater. U.S. 20 Gallons Metric 76 Liters 5 Quarts 5.5 Quarts 4.7 Liters 5.2 Liters 13.4 Quarts 12.6 Liters 2.9 Qts (2.
480 MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant Engine Oil (3.3L and 3.8L Engines) Engine Oil (4.0L Engine) Oil Filter (3.3L and 3.8L Engines) Oil Filter (4.0L Engine) Spark Plugs (3.3L and 3.8L Engines) Spark Plugs (4.0L Engine) Fuel Selection (3.3L and 3.8L Engines) Fuel Selection (4.
MAINTAINING YOUR VEHICLE 481 Chassis Component Automatic Transaxle Brake Master Cylinder Power Steering Reservoir Fluid, Lubricant, or Genuine Part MOPAR威 ATF+4 Automatic Transmission Fluid MOPAR威 DOT 3 and SAE J1703 should be used or equivalent. If DOT 3 brake fluid is not available, then DOT 4 is acceptable. Use only recommended brake fluids.
MAINTENANCE SCHEDULES CONTENTS 䡵 Emissions Control System Maintenance . . . . . . 484 䡵 Maintenance Schedule . . . . . . . . . . . . . . . . . . 484 ▫ Required Maintenance Intervals . . . . . . . . . .
M A I N T E N A N C E 484 MAINTENANCE SCHEDULES EMISSIONS CONTROL SYSTEM MAINTENANCE The Scheduled Maintenance services listed in bold type, must be done at the times or mileages specified to ensure the continued proper functioning of the Emissions Control System. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
MAINTENANCE SCHEDULES 485 M A NOTE: • The oil change indicator message will not monitor the time since the last oil change. Change your vehicle’s oil if it has been six months since your last oil change, even if the oil change indicator message is NOT illuminated. • Change your engine oil more often if you drive your vehicle off-road for an extended period of time. • Under no circumstances should oil change intervals exceed 6,000 miles (10 000 km) or six months, whichever comes first.
M A I N T E N A N C E S C H E D U L E S 8 486 MAINTENANCE SCHEDULES • Check the fluid levels of the coolant reservoir, the brake master cylinder, the power steering and the transaxle and add as needed. • Check all lights and other electrical items for correct operation. At Each Oil Change • Change the engine oil filter. • Inspect the brake hoses and lines. CAUTION! Failure to perform the required maintenance items may result in damage to the vehicle.
MAINTENANCE SCHEDULES 487 M 6,000 Miles (10,000 km) or 6 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. 12,000 Miles (20,000 km) or 12 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter, replace if necessary. ❏ Replace the air conditioning filter.
M 488 MAINTENANCE SCHEDULES A I N 18,000 Miles (30,000 km) or T 18 Months Maintenance E N Service Schedule A ❏ Change the engine oil and engine oil filter. N C ❏ Rotate tires. E 24,000 Miles (40,000 km) or 24 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter, replace if necessary. ❏ Replace the air conditioning filter.
MAINTENANCE SCHEDULES 489 M 30,000 Miles (50,000 km) or 30 Months Maintenance Service Schedule 36,000 Miles (60,000 km) or 36 Months Maintenance Service Schedule 42,000 Miles (70,000 km) or 42 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ Replace the engine air cleaner filter. ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions.
M 490 MAINTENANCE SCHEDULES A I N 48,000 Miles (80,000 km) or 48 Months Maintenance Service T Schedule E ❏ Change the engine oil and engine oil filter. N A ❏ Rotate tires. N ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter, replace if necessary. C E ❏ Replace the air conditioning filter.
MAINTENANCE SCHEDULES 491 M 60,000 Miles (100,000 km) or 60 Months Maintenance Service Schedule 66,000 Miles (110,000 km) or 66 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ Replace the engine air cleaner filter. ❏ Replace the air conditioning filter. ❏ Inspect the brake linings, replace if necessary. ❏ Change the automatic transaxle fluid & filter if using your vehicle for any of the following: police, taxi, fleet or frequent trailer towing.
M 492 MAINTENANCE SCHEDULES A I N 72,000 Miles (120,000 km) or 72 Months Maintenance Service T Schedule E ❏ Change the engine oil and engine oil filter. N A ❏ Rotate tires. N ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter, replace if necessary. C E ❏ Replace the air conditioning filter.
MAINTENANCE SCHEDULES 493 M 84,000 Miles (140,000 km) or 84 Months Maintenance Service Schedule 90,000 Miles (150,000 km) or 90 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter, replace if necessary. ❏ Replace the air conditioning filter. ❏ Inspect the brake linings, replace if necessary. ❏ Change the engine oil and engine oil filter.
M 494 MAINTENANCE SCHEDULES A I N 96,000 Miles (160,000 km) or 96 Months Maintenance Service T Schedule E ❏ Change the engine oil and engine oil filter. N A ❏ Rotate tires. N ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter, replace if necessary. C E ❏ Replace the air conditioning filter. S C H E D U L E S ❏ ❏ ❏ ❏ Inspect Inspect Inspect Inspect the the the the brake linings, replace if necessary. CV Joints. exhaust system.
MAINTENANCE SCHEDULES 495 M 108,000 Miles (180,000 km) or 108 Months Maintenance Service Schedule 114,000 Miles (190,000 km) or 114 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter, replace if necessary. ❏ Replace the air conditioning filter. ❏ Inspect the brake linings, replace if necessary. ❏ Change the engine oil and engine oil filter.
M 496 MAINTENANCE SCHEDULES A I N 120,000 Miles (200,000 km) or 120 Months Maintenance Service T Schedule E ❏ Change the engine oil and engine oil filter. N A ❏ Rotate tires. N ❏ Replace the engine air cleaner filter. C ❏ Replace the air conditioning filter. E ❏ Inspect the brake linings, replace if necessary. S C H E D U L E S ❏ ❏ ❏ ❏ ❏ 126,000 Miles (210,000 km) or 126 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. Inspect the CV Joints.
MAINTENANCE SCHEDULES 497 M 132,000 Miles (220,000 km) or 132 Months Maintenance Service Schedule 138,000 Miles (230,000 km) or 138 Months Maintenance Service Schedule 144,000 Miles (240,000 km) or 144 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter, replace if necessary. ❏ Replace the air conditioning filter.
M 498 MAINTENANCE SCHEDULES A I N 150,000 Miles (250,000 km) or T 150 Months Maintenance E N Service Schedule A ❏ Change the engine oil and engine oil filter. N C ❏ Rotate tires. E ❏ Replace the engine air cleaner filter.
MAINTENANCE SCHEDULES 499 M † This maintenance is recommended by the manufacturer, but is not required to maintain emissions warranty. WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS 䡵 Suggestions For Obtaining Service For Your Vehicle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 503 ▫ Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) . . . . . . . . . . . . 505 ▫ Prepare For The Appointment . . . . . . . . . . . . 503 ▫ Service Contract . . . . . . . . . . . . . . . . . . . . . 505 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . . 503 䡵 Warranty Information (U.S. Vehicles Only) . . . .
502 IF YOU NEED CONSUMER ASSISTANCE 䡵 Publication Order Forms . . . . . . . . . . . . . . . . . 507 ▫ Traction Grades . . . . . . . . . . . . . . . . . . . . . . 509 䡵 Department Of Transportation Uniform Tire Quality Grades . . . . . . . . . . . . . . . . . . . . . . . . 509 ▫ Temperature Grades . . . . . . . . . . . . . . . . . . . 510 ▫ Treadwear . . . . . . . . . . . . . . . . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE 503 SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager. Keep a maintenance log of your vehicle’s service history. This can often provide a clue to the current problem.
504 IF YOU NEED CONSUMER ASSISTANCE This is why you should always talk to an authorized dealer’s service manager first. Most matters can be resolved with this process. • If for some reason you are still not satisfied, talk to the general manager or owner of the authorized dealership. They want to know if you need assistance. • If an authorized dealership is unable to resolve the concern, you may contact the manufacturer’s customer center.
IF YOU NEED CONSUMER ASSISTANCE 505 Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommunication Devices for the Deaf) equipment at its customer center. Any hearing or speech impaired customer, who has access to a TDD or a conventional teletypewriter (TTY) in the United States, can communicate with the manufacturer by dialing 1–800–380–CHRY.
506 IF YOU NEED CONSUMER ASSISTANCE the ownership experience. You’ll be pleased with their sincere efforts to resolve any warranty issues or related concerns. WARNING! Engine exhaust, some of its constituents, and certain vehicle components contain, or emit, chemicals known to the State of California to cause cancer and birth defects, or other reproductive harm.
IF YOU NEED CONSUMER ASSISTANCE 507 a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your authorized dealer, and the manufacturer. To contact NHTSA, you may either call the Auto Safety Hotline toll free at 1–888–327–4236 (TTY: 1–800–424– 9153), or go to http://www.safercar.gov; or write to: Administrator, NHTSA, 400 Seventh Street, SW., Washington, D.C. 20590.
508 IF YOU NEED CONSUMER ASSISTANCE vehicles. A complete working knowledge of the vehicle, system, and/or components is written in straightforward language with illustrations, diagrams, and charts. • Owner’s Manuals These Owner’s Manuals have been prepared with the assistance of service and engineering specialists to acquaint you with specific Chrysler LLC vehicles. Included are starting, operating, emergency and maintenance procedures as well as specifications, capabilities and safety tips.
IF YOU NEED CONSUMER ASSISTANCE 509 DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES The following tire grading categories were established by the National Highway Traffic Safety Administration. The specific grade rating assigned by the tire’s manufacturer in each category is shown on the sidewall of the tires on your vehicle. All passenger car tires must conform to Federal safety requirements in addition to these grades.
510 IF YOU NEED CONSUMER ASSISTANCE Temperature Grades The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
INDEX 10
512 INDEX Adding Engine Coolant (Antifreeze) . . . . . . . . . . 452 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 387 Adding Washer Fluid . . . . . . . . . . . . . . . . . . . . . 449 Additives, Fuel . . . . . . . . . . . . . . . . . . . . . . . . . 381 Adjustable Pedals . . . . . . . . . . . . . . . . . . . . . . . 182 Air Cleaner, Engine (Engine Air Cleaner Filter) . . . 441 Air Conditioner Maintenance . . . . . . . . . . . . . . . 446 Air Conditioning . . . . . . . . . . . . . . . .
INDEX 513 Automatic Headlights . . . . . . . . . . . . . . . . . . . . 174 Automatic Temperature Control (ATC) . . . . . . . . . 310 Automatic Transaxle . . . . . . . . . . . . . . . . . . . . . . 327 Adding Fluid . . . . . . . . . . . . . . . . . . . . . . . . . 459 Fluid Level Check . . . . . . . . . . . . . . . . . . . . . . 459 Interlock System . . . . . . . . . . . . . . . . . . . . . . . 328 Selection Of Lubricant . . . . . . . . . . . . . . . . 458,481 Shifting . . . . . . . . . . . . . . . . . . .
514 INDEX Camera, Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . 192 Capacities, Fluid . . . . . . . . . . . . . . . . . . . . . . . . 479 Caps, Filler Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 387 Oil (Engine) . . . . . . . . . . . . . . . . . . . . . . . . . . 440 Power Steering . . . . . . . . . . . . . . . . . . . . . . . . 338 Radiator (Coolant Pressure) . . . . . . . . . . . . . . . 453 Car Washes . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 515 Computer, Trip/Travel . . . . . . . . . . . . . . . . . . . . 255 Connector UCI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 286 Universal Consumer Interface (UCI) . . . . . . . . . 286 Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 217 Console, Floor . . . . . . . . . . . . . . . . . . . . . . . . . . 217 Console, Overhead . . . . . . . . . . . . . . . . . . . . . . . 194 Console, Removable . . . . . . . . . . . . . . . . . . . . . .
516 INDEX Disposal Antifreeze (Engine Coolant) . . . . . . . . . . . . . . . 454 Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . 441 Domelight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173 Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Door Locks, Automatic . . . . . . . . . . . . . . . . . . . . 34 Door Opener, Garage . . . . . . . . . . . . . . . . . . . . . 197 Drive Shaft Universal Joints . . . . . . . . . . . . . . . .
INDEX 517 Exhaust Gas Caution . . . . . . . . . . . . . . . . . . 53,382 Flooded, Starting . . . . . . . . . . . . . . . . . . . . . . 325 Fuel Requirements . . . . . . . . . . . . . . . . . . 378,479 Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . 438,479,480 Oil Change Interval . . . . . . . . . . . . . . . . . . . . 439 Oil Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . 441 Oil Filler Cap . . . . . . . . . . . . . . . . . . . . . . . . . 440 Oil Filter Disposal . . . . . . . . .
518 INDEX Replacement Parts . . . . . . . . . . . . . . . . . . . . . 386 Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 385 Flooded Engine Starting . . . . . . . . . . . . . . . . . . . 325 Floor Console . . . . . . . . . . . . . . . . . . . . . . . . . . 217 Fluid Capacities . . . . . . . . . . . . . . . . . . . . . . . . . 479 Fluid Leaks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95 Fluid Level Checks Automatic Transaxle . . . . . . . . . . . . . . . . . . . .
INDEX 519 Gasoline, Reformulated . . . . . . . . . . . . . . . . . . . 380 Gauges Coolant Temperature . . . . . . . . . . . . . . . . . . . . 236 Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 236 Speedometer . . . . . . . . . . . . . . . . . . . . . . . . . 237 Tachometer . . . . . . . . . . . . . . . . . . . . . . . . . . 239 Gearshift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 329 General Information . . . . . . . . . . . . . . . 18,27,143,378 Glass Cleaning . . .
520 INDEX Ignition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12,14 Ignition Key Removal . . . . . . . . . . . . . . . . . . . . . 14 Illuminated Entry . . . . . . . . . . . . . . . . . . . . . . . . 20 Immobilizer (Sentry Key) . . . . . . . . . . . . . . . . . . . 15 Infant Restraint . . . . . . . . . . . . . . . . . . . . . . . . 81,83 Information Center, Vehicle . . . . . . . . . . . . . . . . .
INDEX 521 Airbag . . . . . . . . . . . . . . . . . . . . . . 66,71,75,94,244 Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 244 Anti-Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . 237 Automatic Headlights . . . . . . . . . . . . . . . . . . . 174 Back-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 477 Battery Saver . . . . . . . . . . . . . . . . . . . . . . . . . 177 Brake Assist Warning . . . . . . . . . . . . . . . . . . . 348 Brake Warning . . . . . . . . .
522 INDEX Tire Pressure Monitoring (TPMS) . . . . . . . . . . . 245 Turn Signal . . . . . . . . . . . . . . . . . . . . . . . . 476,477 Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 245 Warning (Instrument Cluster Description) . . . . . 236 Load Leveling System . . . . . . . . . . . . . . . . . . . . 224 Loading Vehicle . . . . . . . . . . . . . . . . . . . 216,389,391 Capacities . . . . . . . . . . . . . . . . . . . . . . . . . . . 391 Tires . . . . . . . . . . . . . . . . . . . . . .
INDEX 523 Multi-Function Control Lever . . . . . . . . . . . . . . . 177 Navigation System . . . . . . . . . . . . . . . . . . . . . . . 192 New Vehicle Break-In Period . . . . . . . . . . . . . . . . 93 Occupant Restraints . . . . . . . . . . . . . . . . . . . 55,70,73 Occupant Restraints (Sedan) . . . . . . . . . . . . . 68,70,72 Odometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 240 Oil Change Indicator . . . . . . . . . . . . . . . . 241,248,255 Oil Change Indicator, Reset . . . . . . .
524 INDEX Phone, Cellular . . . . . . . . . . . . . . . . . . . . . . . . . 115 Phone, Hands-Free (UConnect威) . . . . . . . . . . . . . 115 Placard, Tire and Loading Information . . . . . . . . . 354 Power Brakes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 343 Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Lift Gate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 525 Reminder, Seat Belt . . . . . . . . . . . . . . . . . . . . . . . 63 Remote Keyless Entry (RKE) . . . . . . . . . . . . . . . . . 21 Remote Sound System (Radio) Controls . . . . . . . . 299 Remote Starting System . . . . . . . . . . . . . . . . . . . . 28 Removable Floor Console . . . . . . . . . . . . . . . . . . 222 Replacement Keys . . . . . . . . . . . . . . . . . . . . . . . . 16 Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . 437 Replacement Tires . . . . . . . . . . . . . .
526 INDEX Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . 144 Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . 464 Easy Entry . . . . . . . . . . . . . . . . . . . . . . . . . . . 153 Fold in Floor (Stow ⬘n Go) . . . . . . . . . . . . . . . . 149 Heated . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147 Lumbar Support . . . . . . . . . . . . . . . . . . . . . . . 149 Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166 Power . . . . . . . . . . . .
INDEX 527 Remote . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Starting and Operating . . . . . . . . . . . . . . . . . . . . 324 Starting Procedures . . . . . . . . . . . . . . . . . . . . . . 324 Steering Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 338 Shaft Seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . 448 Tilt Column . . . . . . . . . . . . . . . . . . . . . . . . . . 181 Steering Wheel Mounted Sound System Controls . . . . . . . . . . . . . . . . .
528 INDEX Flat Changing . . . . . . . . . . . . . . . . . . . . . . . . 421 General Information . . . . . . . . . . . . . . . . . . . . 358 High Speed . . . . . . . . . . . . . . . . . . . . . . . . . . 360 Inflation Pressures . . . . . . . . . . . . . . . . . . . . . 359 Jacking . . . . . . . . . . . . . . . . . . . . . . . . . . . 412,415 Life of Tires . . . . . . . . . . . . . . . . . . . . . . . . . . 364 Load Capacity . . . . . . . . . . . . . . . . . . . . . 354,355 Pressure Monitor System (TPMS) . .
INDEX 529 Automatic . . . . . . . . . . . . . . . . . . . . . . . . . . . 327 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . 327 Selection of Lubricant . . . . . . . . . . . . . . . . 458,481 Transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . 458 Automatic . . . . . . . . . . . . . . . . . . . . . . . . . . . 458 Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . 458,481 Transmitter Battery Service (Remote Keyless Entry) . . . . . . . . . . . . . . . . . . . .
530 INDEX Warranty Information . . . . . . . . . . . . . . . . . . . . . 506 Washer, Adding Fluid . . . . . . . . . . . . . . . . . . . . . 449 Washing Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . 461 Water Driving Through . . . . . . . . . . . . . . . . . . . . . . 335 Wheel Alignment and Balance . . . . . . . . . . . . . . . 366 Wheel and Wheel Trim . . . . . . . . . . . . . . . . . . . . 462 Wheel and Wheel Trim Care . . . . . . . . . . . . . . . . 462 Wheel Nut Torque . . . . . . . . . . .
INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained personnel. The following must be observed during installation. The positive power connection should be made directly to the battery and fused as close to the battery as possible.
Chrysler LLC 81-226-0919 First Edition Printed in U.S.A.
