VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name Chrysler LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefore. DRIVING AND ALCOHOL Drunken driving is one of the most frequent causes of accidents. Your driving ability can be seriously impaired with blood alcohol levels far below the legal minimum. If you are drinking, don’t drive. Ride with a designated non-drinking driver, call a cab, a friend, or use public transportation.
SECTION TABLE OF CONTENTS PAGE 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83 3 4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION CONTENTS 䡵 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 Vehicle Identification Number . . . . . . . . . . . . . . . 6 䡵 How To Use This Manual . . . . . . . . . . . . . . . . . . 4 䡵 Vehicle Modifications/Alterations . . . . . . . . . . . . 7 䡵 Warnings And Cautions . . . . . . . . . . . . . . . . . . .
4 INTRODUCTION INTRODUCTION This Owner’s Manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your vehicle. It is supplemented by a Warranty Information Booklet and various customer-oriented documents. You are urged to read these publications carefully. Following the instructions and recommendations in this manual will help assure safe and enjoyable operation of your vehicle.
INTRODUCTION 5 1
6 INTRODUCTION WARNINGS AND CAUTIONS This Owner’s Manual contains WARNINGS against operating procedures that could result in an accident or bodily injury. It also contains CAUTIONS against procedures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important information. Observe all Warnings and Cautions.
INTRODUCTION 7 VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS 䡵 A Word About Your Keys . . . . . . . . . . . . . . . . . 12 䡵 Vehicle Security Alarm System — If Equipped . . 19 ▫ Ignition Key Removal . . . . . . . . . . . . . . . . . . 13 ▫ Rearming The System . . . . . . . . . . . . . . . . . . 19 ▫ Key-In-Ignition Reminder . . . . . . . . . . . . . . . . 15 ▫ To Arm The System . . . . . . . . . . . . . . . . . . . . 19 ▫ Locking The Doors With The Key . . . . . . . . . . 15 ▫ To Disarm The System . . . .
10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Using The Express Down Windows Feature — If Equipped. . . . . . . . . . . . . . . . . . . . . . . . 26 ▫ Using The Panic Alarm . . . . . . . . . . . . . . . . . 26 ▫ Programming Additional RKE Transmitters . . . 26 ▫ Battery Replacement . . . . . . . . . . . . . . . . . . . 27 ▫ General Information . . . . . . . . . . . . . . . . . . . . 28 䡵 Remote Start System — If Equipped . . . . . . . . . 29 ▫ How To Use Remote Start . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 ▫ Rear Seat Belts . . . . . . . . . . . . . . . . . . . . . . . 50 ▫ Airbag Deployment Sensors And Controls . . . . 61 ▫ Seat Belt Pretensioners . . . . . . . . . . . . . . . . . . 50 ▫ Event Data Recorder (EDR) . . . . . . . . . . . . . . 67 ▫ Enhanced Seat Belt Reminder System (BeltAlert威) . . . . . . . . . . . . . . . . . . . . . . . . . . 50 ▫ Child Restraints . . . . . . . . . . . . . . . . . . . . . . . 69 ▫ BeltAlert威 Programming . . . . . . . . .
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS The authorized dealer that sold you your vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys from your authorized dealer. Ask your authorized dealer for these numbers and keep them in a safe place. You can insert the double-sided keys into the locks with either side up.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 Ignition Key Removal Automatic Transaxle Place the shift lever in PARK. Turn the ignition switch to the ACC position, push the key and cylinder inward, rotate the key to the LOCK position, and remove the key.
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: • If you try to remove the key before you place the shift lever in PARK, the key may become trapped temporarily in the ignition switch lock cylinder. If this occurs, rotate the key to the right slightly, then remove the key as described. If a malfunction occurs, the system will trap the key in the ignition switch lock cylinder to warn you that this safety feature is inoperable.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 CAUTION! An unlocked car is an invitation to thieves. Always remove key from the ignition and lock all doors when leaving the vehicle unattended. Key-In-Ignition Reminder Opening the driver’s door when the key is in the ignition, sounds a signal to remind you to remove the key. NOTE: • The Key-In-Ignition reminder only sounds when the ignition key is placed in the LOCK or ACC position.
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: A key which has not been programmed is also considered an invalid key even if it is cut to fit the ignition switch lock cylinder for that vehicle. During normal operation, after turning on the ignition switch, the Vehicle Security Light will turn on for three seconds for a bulb check. If the light remains on after the bulb check, it indicates that there is a problem with the electronics.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 All of the keys provided with your vehicle have been programmed to the vehicle electronics. Replacement Keys NOTE: Only keys that have been programmed to the vehicle electronics can be used to start the vehicle. Once a Sentry Key威 has been programmed to a vehicle, it cannot be programmed to any other vehicle. At the time of purchase, the original owner is provided with a four-digit Personal Identification Number (PIN).
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE addition, the Vehicle Security Light will begin to flash. Turn the ignition switch to the LOCK position and remove the second key. 4. Insert a blank Sentry Key威 into the ignition switch. Turn the ignition switch to the ON position within 60 seconds. After 10 seconds, a single chime will sound. In addition, the Vehicle Security Light will stop flashing.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 VEHICLE SECURITY ALARM SYSTEM — IF EQUIPPED The Vehicle Security Alarm system monitors the doors and trunk for unauthorized entry and ignition switch for unauthorized operation. If something triggers the alarm, the system will signal for about 18 minutes. For the first three minutes, the horn will sound intermittently and the headlights, park lights, taillights and the indicator light in the cluster will flash.
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: • During the 16 second arming period, if a door is opened or the ignition switch is turned ON, the system will automatically disarm. • The system remains armed during trunk entry. Pressing the trunk button will not disarm the system. If someone enters the vehicle through the trunk and opens any door, the alarm will sound.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 Tamper Alert If the alarm was triggered, but the warning signals have timed out, the park and taillights flash three times (instead of the normal twice), and the horn will chirp three times, when unlocking the vehicle with a valid RKE transmitter to alert the driver. ILLUMINATED ENTRY SYSTEM — IF EQUIPPED The courtesy/reading lights will turn on when you use the Remote Keyless Entry (RKE) transmitter or open either door.
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: • The line of transmission must not be blocked with metal objects. • Inserting the key into the ignition switch disables all buttons on the RKE transmitter. To Unlock the Doors Press and release the UNLOCK button on the RKE transmitter once to unlock the driver’s door, or twice to unlock all doors. The turn signal lights will flash to acknowledge the unlock signal. The Illuminated Entry system (if equipped) will also turn on.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 • For vehicles not equipped with the EVIC, perform the following procedure: 1. Press and hold the LOCK button on a programmed RKE transmitter for at least four seconds, but not longer than 10 seconds. Then, press and hold the UNLOCK button while still holding the LOCK button. 2. Release both buttons at the same time. 3.
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • For vehicles not equipped with the EVIC, perform the following procedure: 1. Press and hold the UNLOCK button on a programmed RKE transmitter for at least four seconds, but not longer than 10 seconds. Then, press and hold the LOCK button while still holding the UNLOCK button. 2. Release both buttons at the same time. 3.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 Sound Horn with Lock This feature will cause the horn to chirp when the doors are locked with the RKE transmitter. This feature can be turned on or off. To change the current setting, proceed as follows: 2. Release both buttons at the same time.
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Using the Express Down Windows Feature — If Equipped This feature allows you to remotely lower both front door windows at the same time. To use this feature, press and release the UNLOCK button on the RKE transmitter and then immediately press and hold the UNLOCK button until the windows lower to the level desired or until they lower completely.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 Battery Replacement The recommended replacement battery is CR2032. NOTE: Perchlorate Material — special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate. 2 1. With the RKE transmitter buttons facing down, use a flat blade to pry the two halves of the RKE transmitter apart. Make sure not to damage the seal during removal. Separating RKE Transmitter Halves 2. Remove and replace the batteries.
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE General Information This device complies with part 15 of FCC rules and with RS-210 of Industry Canada. Operation is subject to the following conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference that may be received including interference that may cause undesired operation.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 REMOTE START SYSTEM — IF EQUIPPED Remote start conveniently starts the engine from outside the vehicle by using the Remote Keyless Entry (RKE) transmitter while maintaining security. The system has a targeted range of up to 328 ft (100 m). The vehicle must be locked, the deck lid and hood closed and the shift lever in PARK in order to start the engine using the Remote Start button on the RKE transmitter.
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE How to Use Remote Start All of the following conditions must be met before the engine will remote start: • Shift lever in PARK • Doors closed • Hood closed • Trunk closed • Hazard switch off • Brake switch inactive (brake pedal not pressed) • Ignition key removed from ignition switch • Battery at an acceptable charge level, and • RKE PANIC button not pressed To Enter Remote Start Mode Press and release the REMOTE START button on the RKE transmitter twice.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 To Exit Remote Start Mode Without Driving the Vehicle Allow the engine to run for the entire 15 minute cycle. To Exit Remote Start Mode and Drive the Vehicle Before the end of the 15 minute cycle, press and release the UNLOCK button on the RKE transmitter to unlock the doors and disarm the Vehicle Security Alarm (if equipped). Then, within 15 minutes, insert the key into the ignition switch and turn the switch to the ON position.
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE DOOR LOCKS WARNING! Manual Door Locks To lock each door, push the door lock plunger on each door trim panel downward. To unlock each door, pull the door lock plunger on each door trim panel upward. Manual Lock Plunger • For personal security and safety in the event of an accident, lock the vehicle doors as you drive as well as when you park and leave the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 CAUTION! An unlocked vehicle is an invitation to thieves. Always remove the key from the ignition and lock all of the doors when leaving the vehicle unattended. 2 Power Door Locks A door lock switch is located on the driver and passenger door panel. Press this switch to lock or unlock the doors. Power Door Lock Switch Automatic Door Locks — If Equipped When enabled, your door locks will lock automatically when the vehicle’s speed exceeds 15 mph (24 km/h).
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Automatic Unlock Doors On Exit The doors will unlock automatically on vehicles with power door locks if: Automatic Unlock Doors On Exit Programming The Automatic Unlock Doors on Exit feature can be enabled or disabled as follows: 1. The Automatic Unlock Doors on Exit feature is enabled.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 3. Depress the power door unlock switch to unlock the doors. 4. A single chime will indicate the completion of the programming. 2 5. Repeat these steps if you want to return this feature to its previous setting. NOTE: Use the Automatic Unlock Doors on Exit feature in accordance with local laws. Child Protection Door Lock System (Rear Doors) The Child Protection Door Lock (Rear Doors) are located inside the rear edge of the door.
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged. NOTE: For emergency exit with the system engaged, move the lock plunger up (UNLOCKED position), roll down the window, and open the door with the outside door handle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 WARNING! To cancel the Auto Down movement, operate the switch either in the up or down direction and release the switch. Never leave children in a vehicle, with the keys in the ignition switch. Occupants, particularly unattended children, can become entrapped by the windows while operating the power window switches. Such entrapment may result in serious injury or death.
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Auto Window Up — If Equipped Lift the window switch to the second detent, release, and the window will go up automatically. To cancel the Auto Up movement, operate the switch either in the up or down direction and release the switch. To close the window part way, lift the window switch to the first detent and release it when you want the window to stop.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 open or partially open positions. This is a normal occurrence and can be minimized. If the buffeting occurs with the rear windows open, then open the front and rear windows together to minimize the buffeting. If the buffeting occurs with the sunroof open, then adjust the sunroof opening to minimize the buffeting.
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To unlatch the trunk lid from outside the vehicle, press and release the TRUNK button on the RKE transmitter two times. With the ignition ON, the word “deck” will display in place of the odometer display indicating that the trunk is open. The odometer display will reappear once the trunk is closed or if the trip button is depressed. With the key in the lock position or with the key out, the word “deck” will display until the trunk is closed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 Trunk Internal Emergency Release As a security measure, a Trunk Internal Emergency Release lever is built into the trunk latching mechanism. In the event of an individual being locked inside the trunk, the trunk can be simply opened by pulling on the glow-in-the-dark handle attached to the trunk latching mechanism.
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE OCCUPANT RESTRAINTS Some of the most important safety features in your vehicle are the restraint systems.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 more information on LATCH, see Lower Anchors and Tether for CHildren (LATCH) in this section. NOTE: The front airbags have a multistage inflator design. This allows the airbag to have different rates of inflation that are based on collision severity. Please pay close attention to the information in this section. It tells you how to use your restraint system properly to keep you and your passengers as safe as possible.
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belts All seating positions in your vehicle are equipped with lap/shoulder belts. The belt webbing retractor will lock only during very sudden stops or collisions. This feature allows the shoulder part of the belt to move freely with you under normal conditions. But in a collision, the belt will lock and reduce your risk of striking the inside of the vehicle or being thrown out.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2 2. The seat belt latch plate is above the back of the front seat, next to your arm. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to allow the belt to go around your lap. Pulling Out the Latch Plate 3.
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you as well. In a sudden stop, you could move too far forward, increasing the possibility of injury. Wear your seat belt snugly.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 WARNING! • A belt that is worn under your arm is very dangerous. Your body could strike the inside surfaces of the vehicle in a collision, increasing head and neck injury. A belt worn under the arm can cause internal injuries. Ribs aren’t as strong as shoulder bones. Wear the belt over your shoulder so that your strongest bones will take the force in a collision. • A shoulder belt placed behind you will not protect you from injury during a collision.
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as possible and keep it snug. • A twisted belt can’t do its job as well. In a collision, it could even cut into you. Be sure the belt is straight. If you can’t straighten a belt in your vehicle, take it to your authorized dealer and have it fixed. 5.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 Lap/Shoulder Belt Untwisting Procedure Use the following procedure to untwist a twisted lap/ shoulder belt. 1. Position the latch plate as close as possible to the anchor point. Adjustable Upper Shoulder Belt Anchorage In the front seat, the shoulder belt can be adjusted upward or downward to position the belt away from your neck. Push anchorage button to release the anchorage, and move it up or down to the position that serves you best. 2.
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE As a guide, if you are shorter than average, you will prefer a lower position, and if you are taller than average, you’ll prefer a higher position. When you release the anchorage, try to move it up or down to make sure that it is locked in position. Rear Seat Belts The shoulder belt anchorages of the rear three point belts are nonadjustable for outboard and center rear passengers on sedans.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 warning is triggered, BeltAlert威 will continue to chime and flash the Seat Belt Warning Light for 96 seconds or until the driver’s seat belt is buckled. BeltAlert威 will be reactivated if the driver’s seat belt is unbuckled for more than 10 seconds and the vehicle speed is greater than 5 mph (8 km/h).
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Automatic Locking Mode In this mode, the shoulder belt is automatically prelocked. However, the belt will still retract to remove any slack in the shoulder belt. The Automatic Locking mode is available on all passenger-seating positions. Use the Automatic Locking mode anytime a child safety seat is installed in a passenger seating position. Children 12 years old and younger should be properly restrained in the rear seat whenever possible.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 dealer can provide you with a seat belt extender. This extender should be used only if the existing belt is not long enough. When it is not required, remove the extender, and stow it. is mounted in the instrument panel, above the glove compartment. The words SRS AIRBAG are embossed on the airbag covers. WARNING! Using a seat belt extender when not needed can increase the risk of injury in a collision.
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: The front airbags are certified to the Federal regulations that allow less forceful deployment. • Driver Airbag The front airbags have a multistage inflator design. This may allow the airbag to have different rates of inflation that are based on collision severity and occupant size.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 Front Seat Airbag Features The front airbag system has dual-stage driver and front passenger airbags. This system provides output appropriate to the level of crash severity as determined by the Occupant Restraint Controller (ORC) and the impact sensors at the front of the car. The first stage inflator is triggered immediately during an impact that requires airbag deployment.
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Supplemental Front Seat-Mounted Thorax Side Airbags Front seat-mounted thorax side airbags provide enhanced protection and work together with supplemental Side Airbag Inflatable Curtains (SABIC) to help protect an occupant during a side impact. The seat-mounted side airbag is marked with an airbag label sewn into the outboard side of the seat.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 Supplemental Side Airbag Inflatable Curtain (SABIC) — If Equipped Supplemental Side Airbag Inflatable Curtain (SABIC) Airbags offer side-impact protection to front and rear seat outboard occupants in addition to that provided by the body structure. Each airbag features inflated chambers place adjacent to the head of each outboard occupant that reduce the potential for side-impact head injuries.
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! (Continued) • Do not put anything on or around the airbag covers or attempt to open them manually. You may damage the airbags and you could be injured because the airbags are not there to protect you. These protective covers for the airbag cushions are designed to open only when the airbags are inflating.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 The seat belts are designed to protect you in many types of collisions. The front airbags deploy in moderate to severe frontal collisions. If your vehicle is equipped, the side airbag on the crash side of the vehicle is triggered in moderate to severe side collisions. In certain types of collisions, both the front and side airbags may be triggered.
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE You should read the instructions provided with your child restraint to make sure that you are using it properly. 2. All occupants should wear their lap and shoulder belts properly. 3. The driver and front passenger seats should be moved back as far as practical to allow the front airbags room to inflate. 4. If your vehicle has thorax side airbags, do not lean against the door as airbags will inflate forcefully into the space between you and the door. 5.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 Airbag Deployment Sensors and Controls Occupant Restraint Controller (ORC) The Occupant Restraint Controller System (ORC) is part of a Federally regulated safety system required for this vehicle. The ORC determines if a frontal collision is severe enough to require the airbags to inflate.
62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Ignoring the Airbag Warning Light in your instrument panel could mean you won’t have the airbags to protect you in a collision. If the light does not come on, stays on after you start the vehicle, or if it comes on as you drive, have the airbag system checked right away.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 The following requirements must be strictly adhered to: • Do not make any modifications to the front passenger seat components, assembly, or to the seat cover in any way. • Do not use prior or future model year seat covers not designated for the specific model being repaired. Always use the correct seat cover specified for the vehicle. • Do not replace the seat cover with an aftermarket seat cover.
64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Flashes hazard lights • Turns on the interior lights which remain on as long as the battery has power or until the ignition key is removed • Unlocks the doors automatically If a Deployment Occurs The airbag systems are designed to deploy when the Occupant Restraint Controller (ORC) detect a moderateto-severe collision, to help restrain the driver and front passenger, and then immediately deflate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 irritation, move to fresh air. If the irritation continues, see your doctor. If these particles settle on your clothing, follow the garment manufacturer’s instructions for cleaning. • It is not advisable to drive your vehicle after the airbags have deployed. If you are involved in another collision, the airbags will not be in place to protect you. WARNING! Deployed airbags and seat belt pretensioners cannot protect you in another collision.
66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Perchlorate Material — special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate WARNING! Do not attempt to modify any part of your advanced airbag system. The airbag may inflate accidentally or may not function properly if modifications are made. Take your vehicle to an authorized dealer for any advanced airbag system service.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 located on the inside of the fuse block cover for the proper airbag fuses. See your authorized dealer if the fuse is good.
68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE court with legal jurisdiction (i.e., pursuant to a warrant). A copy of the data will be provided to the custodial entity upon request. General data that does not identify particular vehicles or crashes may be released for incorporation in aggregate crash databases, such as those maintained by the US government and various states.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 • Transmission gear selection • Cruise control status • Traction/stability control status • Tire Pressure Monitoring System status (if equipped) Child Restraints Everyone in your vehicle needs to be buckled up all thetime, including babies and children. Every state in the United States and all Canadian provinces require that small children ride in proper restraint systems. This is the law, and you can be prosecuted for ignoring it.
70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Infants and Small Children • Safety experts recommend that children ride rearward-facing in the vehicle until they are at least one year old and weigh at least 20 lbs (9 kg). Two types of child restraints can be used rearward-facing: infant carriers and convertible child seats. Both types of child restraints are held in the vehicle by the lap/shoulder belt or the LATCH child restraint anchorage system.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 The belt-positioning booster seat is for children weighing more than 40 lbs (18 kg), but who are still too small to fit the vehicle’s seat belts properly. If the child cannot sit with knees bent over the vehicle’s cushion while the child’s back is against the seatback, then the child should use a belt-positioning booster seat. The child and booster seat are held in the vehicle by the lap/shoulder belt.
72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards. We also recommend that you make sure that you can install the child restraint in the vehicle where you will use it, before you buy it. • The restraint must be appropriate for your child’s weight and height. Check the label on the restraint for weight and height limits. • Carefully follow the instructions that come with the restraint.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 CAUTION! When your child restraint is not in use, secure it in the vehicle with the seat belt or remove it from the vehicle. Don’t leave it loose in the vehicle. In a sudden stop or collision, it could strike the occupants or seatbacks and cause serious personal injury. NOTE: For additional information, refer www.seatcheck.org or call 1–866–SEATCHECK.
74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Rear Seat LATCH Anchors Child restraints systems having attachments designed to connect to the lower anchorages are now available. Child restraints having tether straps and hooks for connection to the top tether anchorage have been available for some time. In fact, many child restraint manufacturers will provide add-on tether strap kits for some of their older products. Tether anchorage kits are also available for most older vehicles.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 have tether straps, and you are urged to take advantage of all of the available attachments provided with your child restraint in any vehicle. NOTE: When using the LATCH attaching system to install a child restraint, please ensure that all seat belts not being used for occupant restraints are stowed and out of reach of children.
76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE In addition, there are tether strap anchorages behind each rear seating position located in the panel between the rear seatback and the rear window. These tether strap anchorages are under a plastic cover with this symbol on it. Many, but not all restraint systems will be equipped with separate straps on each side, with each having a hook or connector for attachment to the lower anchorage and a means of adjusting the tension in the strap.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77 reach. If the buckled seat belt interferes with the child restraint installation, instead of tucking the seat belt behind the child restraint, route the seat belt through the child restraint belt path and then buckle it. This should stow the seat belt out of the reach of an inquisitive child. Remind all children in the vehicle that the seat belts are not toys and should not be played with, and never leave your child unattended in the vehicle.
78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Route the tether strap to provide the most direct path for the strap between the anchor and the child seat. If your vehicle is equipped with adjustable rear head restraints, raise the head restraint, and where possible, route the tether strap under the head restraint and between the two posts. If not possible, lower the head restraint and pass the tether strap around the outboard side of the head restraint. 3.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 79 In the rear seat, you may have trouble tightening the lap/shoulder belt on the child restraint because the buckle or latch plate is too close to the belt path opening on the restraint. Disconnect the latch plate from the buckle and twist the short buckle-end belt several times to shorten it. Insert the latch plate into the buckle with the release button facing out.
80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Transporting Pets Airbags deploying in the front seat could harm your pet. An unrestrained pet will be thrown about and possibly injured, or injure a passenger during panic braking or in a collision. Pets should be restrained in the rear seat in pet harnesses or pet carriers that are secured by seat belts. ENGINE BREAK-IN RECOMMENDATIONS A long break-in period is not required for the engine in your vehicle. Drive moderately during the first 300 miles (500 km).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 81 SAFETY TIPS WARNING! Exhaust Gas WARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO) which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (CO), follow these safety tips: Do not run the engine in a closed garage or in confined areas any longer than needed to move your vehicle in or out of the area.
82 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag Warning Light The Airbag Warning Light should come on and remain on for six to eight seconds as a bulb check when the ignition switch is first turned ON. If the LED is not lit during starting, have it checked. If the light stays on or comes on while driving, have the system checked by an authorized dealer. Defroster Check operation by selecting the defrost mode and place the blower control on high speed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 3 䡵 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87 ▫ Phone Call Features . . . . . . . . . . . . . . . . . . . 101 ▫ Inside Day/Night Mirror . . . . . . . . . . . . . . . . 87 ▫ UConnect威 System Features . . . . . . . . . . . . . 104 ▫ Automatic Dimming Mirror — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 88 ▫ Advanced Phone Connectivity . . . . . . . . . . . 109 ▫ Power Mirrors . . . . . . . . . . . . .
84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Voice Training . . . . . . . . . . . . . . . . . . . . . . . 124 䡵 Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135 䡵 Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125 ▫ Map/Reading/Interior Lights . . . . . . . . . . . . 135 ▫ Manual Front Seat Adjustment . . . . . . . . . . . 125 ▫ Headlights, Parking Lights And Instrument Panel Lights . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85 䡵 Windshield Wipers And Washers . . . . . . . . . . . 141 ▫ To Accelerate For Passing . . . . . . . . . . . . . . . 148 ▫ Intermittent Wiper System . . . . . . . . . . . . . . 142 䡵 Garage Door Opener — If Equipped . . . . . . . . 148 ▫ Mist Feature . . . . . . . . . . . . . . . . . . . . . . . . 143 ▫ Programming HomeLink威 . . . . . . . . . . . . . . 149 ▫ Headlights With Wipers Feature (Available With Auto Headlights Only) . . . . . . . . . . . . .
86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Sunroof Maintenance . . . . . . . . . . . . . . . . . . 157 䡵 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163 ▫ Ignition Off Operation . . . . . . . . . . . . . . . . . 157 ▫ Driver’s Side Sunglass Holder — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 163 䡵 Electrical Power Outlets . . . . . . . . . . . . . . . . . 158 ▫ Cargo Area . . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 MIRRORS Inside Day/Night Mirror A two-point pivot system allows for horizontal and vertical mirror adjustment. Adjust the mirror to center on the view through the rear window. 3 Headlight glare can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle). The mirror should be adjusted while set in the day position (toward the windshield).
88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Dimming Mirror — If Equipped This mirror will automatically adjust for headlight glare from vehicles behind you. Push in the button on the face of the mirror to activate the dimming feature. 1 — Auto Dimming Mirror Power Indicator 2 — On/Off Switch 3 — Auto Dimming Mirror Sensor CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 Power Mirrors The power mirrors switch is located on the drivers door trim panel. The rotary knob has three separate positions: L for the left mirror, O for Off; and R for the right mirror. After selecting a mirror, move the knob in the same direction you want the mirror to move. When finished, return the knob to the center Off position to guard against accidentally moving a mirror position.
90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Adjusting Sideview Mirrors Outside Mirror — Driver’s Side Adjust the outside mirror to center on the adjacent lane of traffic, with a slight overlap of the view obtained on the inside mirror. Illuminated Vanity Mirrors — If Equipped An illuminated vanity mirror is on each sun visor. To use the mirror, lower the sun visor and rotate the mirror cover upward. The lights will turn on automatically. Closing the mirror cover turns off the lights.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91 HANDS-FREE COMMUNICATION (UConnect姞) — IF EQUIPPED NOTE: The sales code RER and REU radios contain an integrated Hands-Free Communication (UConnect威) system. Refer to your “Navigation User’s Manual” for UConnect威 system operating instructions for these radios. Radio sales code can be located on the lower right corner of the Radio faceplate. UConnect威 is a voice-activated, hands-free, in-vehicle communications system.
92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The UConnect威 system is driven through your Bluetooth威 “Hands-Free Profile” cellular phone. UConnect威 features Bluetooth威 technology - the global standard that enables different electronic devices to connect to each other without wires or a docking station, so UConnect威 works no matter where you stow your cellular phone (be it your purse, pocket, or briefcase), as long as your phone is turned on and has been paired to the vehicle’s UConnect威 system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 The UConnect威 system is fully integrated with the vehicle’s audio system. The volume of the UConnect威 system can be adjusted either from the radio volume control knob or from the steering wheel radio control (right switch), if so equipped. The radio display will be used for visual prompts from the UConnect威 system such as ⬙CELL⬙ or caller ID on certain radios.
94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Help Command If you need assistance at any prompt, or if you want to know your options at any prompt, say ⬙Help⬙ following the beep. The UConnect威 system will play all the options at any prompt if you ask for help. To activate the UConnect威 system from idle, simply press the PHONE button and follow the audible prompts for directions. All UConnect威 system sessions begin with a press of the PHONE button on the radio control head.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 • For identification purposes, you will be prompted to give the UConnect威 system a name for your cellular phone. Each cellular phone that is paired should be given a unique phone name. • You will then be asked to give your cellular phone a priority level between one and seven, with one being the highest priority. You can pair up to seven cellular phones to your UConnect威 system.
96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The system will prompt you to say the name of the person you want to call. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Phonebook New Entry.⬙ • After the ⬙Ready⬙ prompt and the following beep, say the name of the person you want to call. For example, you can say ⬙John Doe,⬙ where John Doe is a previously stored name entry in the UConnect威 phonebook or downloaded phonebook.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 The UConnect威 system will allow you to enter up to 32 names in the phonebook with each name having up to four associated phone numbers and designations. Each language has a separate 32-name phonebook accessible only in that language. In addition, if equipped and supported by your phone, UConnect威 automatically downloads your mobile phone’s phonebook.
98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • This downloaded phonebook cannot be edited or deleted on the UConnect威. These can only be edited on the mobile phone. The changes are transferred and updated to UConnect威 on the next phone connection. Phonebook Download — Single Entry If equipped and supported by your phone, UConnect威 allows the user to download entries from their phone via Bluetooth威. To use this feature, press the PHONE button and say “Phonebook Download.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99 • Press the PHONE button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Phonebook Edit.⬙ • You will then be asked for the name of the phonebook entry that you wish to edit. • Next, choose the number designation (home, work, mobile, or pager) that you wish to edit. • When prompted, recite the new phone number for the phonebook entry that you are editing.
100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After you enter the name, the UConnect威 system will ask you which designation you wish to delete: home, work, mobile, pager, or all. Say the designation you wish to delete. • Note that only the phonebook entry in the current language is deleted. • Automatic downloaded phonebook entries cannot be deleted or edited. Delete/Erase “All” UConnect威 Phonebook Entries • Press the PHONE button to begin.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 • The UConnect威 system will then prompt you as to the number designation you wish to call. • The selected number will be dialed. Phone Call Features The following features can be accessed through the UConnect威 system if the feature(s) are available on your cellular service plan. For example, if your cellular service plan provides three-way calling, this feature can be accessed through the UConnect威 system.
102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Making a Second Call While Current Call is in Progress To make a second call while you are currently on a call, press the VOICE RECOGNITION button and say ⬙Dial⬙ or ⬙Call⬙ followed by the phone number or phonebook entry you wish to call. The first call will be on hold while the second call is in progress. To go back to the first call, refer to ⬙Toggling Between Calls⬙ in this section. To combine two calls, refer to ⬙Conference Call⬙ in this section.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 Call Termination To end a call in progress, momentarily press the PHONE button. Only the active call(s) will be terminated and if there is a call on hold, it will become the new active call. If the active call is terminated by the far end, a call on hold may not become active automatically. This is cell phone-dependent. To bring the call back from hold, press and hold the PHONE button until you hear a single beep. Redial • Press the PHONE button to begin.
104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE UConnect姞 System Features Language Selection To change the language that the UConnect威 system is using: • Press the PHONE button to begin. • After the ⬙Ready⬙ prompt and the following beep, say the name of the language you wish to switch to English, Espanol, or Francais. • Continue to follow the system prompts to complete the language selection. After selecting one of the languages, all prompts and voice commands will be in that language.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 Canada and 060 for Mexico). The number dialed may not be applicable with the available cellular service and area. • If supported, this number may be programmable on some systems. To do this, press the PHONE button and say ‘Setup’, followed by ‘Emergency’. • The UConnect威 system does slightly lower your chances of successfully making a phone call as to that for the cell phone directly.
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Paging To learn how to page, refer to ⬙Working with Automated Systems.⬙ Paging works properly except for pagers of certain companies, which time out a little too soon to work properly with the UConnect威 system. Voice Mail Calling To learn how to access your voice mail, refer to ⬙Working with Automated Systems.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 send the corresponding phone number associated with the phonebook entry, as tones over the phone. NOTE: • You may not hear all of the tones due to cellular phone network configurations. This is normal. • Some paging and voice mail systems have system time out settings that are too short and may not allow the use of this feature.
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Dialing Using the Cellular Phone Keypad You can dial a phone number with your cellular phone keypad and still use the UConnect威 system (while dialing via the cellular phone keypad, the user must exercise caution and take precautionary safety measures). By dialing a number with your paired Bluetooth威 cellular phone, the audio will be played through your vehicle’s audio system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 Advanced Phone Connectivity List Paired Cellular Phone Names Transfer Call to and from Cellular Phone The UConnect威 system allows ongoing calls to be transferred from your cellular phone to the UConnect威 system without terminating the call. To transfer an ongoing call from your UConnect威 paired cellular phone to the UConnect威 system or vice versa, press the VOICE RECOGNITION button and say ⬙Transfer Call.⬙ • Press the PHONE button to begin.
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Select Another Cellular Phone This feature allows you to select and start using another phone paired with the UConnect威 system. • Press the PHONE button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Setup Select Phone⬙ and follow the prompts. • You can also press the VOICE RECOGNITION button at any time while the list is being played, and then choose the phone that you wish to select.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 Voice Training For users experiencing difficulty with the system recognizing their voice commands or numbers, the UConnect威 system Voice Training feature may be used. To enter this training mode, follow one of the two following procedures: From outside the UConnect威 mode (e.g.
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Performance is maximized under: • low-to-medium blower setting, • low-to-medium vehicle speed, • low road noise, • smooth road surface, • fully closed windows, • dry weather condition. • Even though the system is designed for users speaking in North American English, French, and Spanish accents, the system may not always work for some.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 Far End Audio Performance • Audio quality is maximized under: • low-to-medium blower setting, • low-to-medium vehicle speed, • low road noise, • smooth road surface, • fully closed windows, • dry weather conditions, and • operation from the driver’s seat. • Performance, such as audio clarity, echo, and loudness to a large degree rely on the phone and network, and not the UConnect威 system.
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 3
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 Primary zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location all Voice Commands Alternate(s) Voice Commands Primary Alternate(s) call cancel confirmation prompts continue delete dial download edit emergency English erase all Espanol Francais help home 3
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Primary language list names list phones mobile mute mute off new entry no pager pair a phone phone pairing phonebook previous record again redial Voice Commands Alternate(s) pairing phone book Voice Commands Primary Alternate(s) return to main menu return or main menu select phone select send set up phone settings or phone set up towing assistance transfer call UConnect威 Tutorial try again voice training work yes
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 General Information This device complies with Part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired operation.
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE When you press the VR hard-key, you will hear a beep. The beep is your signal to give a command. NOTE: If you do not say a command within a few seconds, the system will present you with a list of options. If you ever wish to interrupt the system while it lists options, press the VR hard-key, listen for the beep, and say your command. Pressing the VR hard-key while the system is speaking is known as “barging in.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 Commands The Voice Recognition system understands two types of commands. Universal commands are available at all times. Local commands are available if the supported radio mode is active. Changing the Volume 1. Start a dialogue by pressing the VR hard-key. 2. Say a command (e.g., “Help”). 3. Use the ON/OFF VOLUME rotary knob to adjust the volume to a comfortable level while the Voice Recognition system is speaking.
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Radio AM (or Radio Long Wave or Radio Medium Wave — If Equipped) To switch to the AM band say “AM” or “Radio AM”. In this mode, you may say the following commands: • “Frequency” (to change the frequency) • “Next Station” (to select the next station) • “Previous Station” (to select the previous station) • “Radio Menu” (to switch to the radio menu) • “Main Menu” (to switch to the main menu) Radio FM To switch to the FM band say “FM” or “Radio FM”.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 Disc To switch to the disc mode say “Disc”. In this mode, you may say the following commands: • “Track” (#) (to change the track) • “Next Track” (to play the next track) • “Previous Track” (to play the previous track) • “Main Menu” (to switch to the main menu) Memo To switch to the voice recorder mode say “Memo”.
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE System Setup To switch to system setup say “Setup”. In this mode, you may say the following commands: • “Language English” • “Language French” • “Language Spanish” • “Tutorial” • “Voice Training” NOTE: Keep in mind that you have to press the VR hard-key first and wait for the beep before speaking the “Barge In” commands.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 SEATS Manual Front Seat Adjustment The manual seat adjustment bar is at the front of the seat, near the floor. Pull the bar upward to move the seat forward or rearward. Release the bar once the seat is in the position desired. Then, using body pressure, move forward and rearward on the seat to be sure that the seat adjusters have latched.
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust the seat only while the vehicle is parked. Driver Seat Manual Height Adjuster — If Equipped A lever style height adjustment feature enhances comfort for petite as well as tall drivers.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 Reclining Bucket Seats The recliner control is on the side of the seat. To recline, lean forward slightly before lifting the lever, then lean back to the desired position and release the lever. Lean forward and lift the lever to return the seatback to its normal position. Seatback Adjustment WARNING! • Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control.
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Lumbar Support — If Equipped This feature allows you to increase or decrease the amount of lumbar support. The control lever is located on the outboard side of the driver’s seatback. Turn the control lever downward to increase and upward to decrease the desired amount of lumbar support. Power Seats — If Equipped The power seat switches are on the outboard side of the seat near the floor.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 CAUTION! Do not place any article under a power seat as it may cause damage to the seat controls. WARNING! Adjustable Head Restraints Head restraints can reduce the risk of whiplash injury in the event of impact from the rear. Adjust the restraints so that the upper edge is as high as practical. To raise, pull up on the head restraint. To lower, depress the button on the post guide and push down on the head restraint.
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Heated Seats — If Equipped This feature heats leather or cloth front driver and passenger seats. The switches for the heated seats are located in the center console above the climate controls. Press the switch once to choose High (two lights), press it a second time to choose Low (one light), press it a third time to turn the heater Off (no lights).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 Fold Flat Passenger Seat Back The recline handle on the front passenger seat also releases the seatback to fold forward. The hard seatback features a work surface and a molded rim for retaining items stored on the seatback panel.
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Folding Rear Seat To provide additional storage area, the rear seatback can be folded forward. Pull on the loops shown in the picture to fold down either or both seatbacks. When returning the rear seatback to the upright position, be sure the seatback is latched. Folding Rear Seats WARNING! The rear cargo area of the vehicle (with the rear seatbacks in the locked-up or folded down position) should not be used as a play area by children.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 Folding Rear Seat Center Armrest The rear seat is equipped with a folding armrest with cupholders. TO OPEN AND CLOSE THE HOOD To open the hood, two latches must be released. 1. Pull the hood release lever located under the left side of the instrument panel.
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Then lift the secondary latch located under the front edge of the hood, near the center and raise the hood. Hood Prop Rod Hole Location Hood Safety Catch Use the hood prop rod to secure the hood in the open position. Place the upper end of the prop rod in the hole on the left underside of the hood. Before closing the hood, make sure to stow the prop rod in its proper location. To prevent possible damage, do not slam the hood to close it.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 WARNING! If the hood is not fully latched it could fly up when the vehicle is moving and block your forward vision. You could have a collision. Be sure all hood latches are fully latched before driving. lighting also comes on when a door is opened or the dimmer control is turned fully upward, past the second detent. 3 LIGHTS Map/Reading/Interior Lights These lights are mounted between the sun visors above the rearview mirror.
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To protect the battery, the interior lights will turn off automatically 10 minutes after the ignition switch is moved to the LOCK position. This will occur if the interior lights were switched on manually or are on because a door is open. To restore interior light operation, either turn the ignition switch ON or cycle the light switch.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 To change the brightness of the instrument panel lights, rotate the center portion of the multifunction lever up or down. Automatic Headlight System — If Equipped Turning the end of the multifunction lever to the third detent (AUTO), will activate the automatic headlight system. With the engine running and the multifunction lever in the AUTO position, the headlights will turn on and turn off based on the surrounding light levels.
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Flash-To-Pass You can signal another vehicle with your headlights by lightly pulling the multifunction lever toward you. This will cause the headlights to turn on at high beam and remain on until the lever is released. NOTE: If the multifunction lever is held in the flash-topass position for more than 15 seconds, the high beams will shut off. If this occurs, wait 30 seconds for the next flash-to-pass operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 Turn Signals Move the multifunction lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights. You can signal a lane change by moving the lever partially up or down without moving beyond the detent. Front Fog Light Control NOTE: The front fog lights will only operate with the headlights on low beam. Selecting high beam headlights will turn off the front fog lights.
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If either light remains on and does not flash, or there is a very fast flash rate, check for a defective outside light bulb. If an indicator fails to light when the lever is moved, it would suggest that the fuse or indicator bulb is defective. High Beam/Low Beam Select Switch Push the multifunction lever away from you to switch the headlights to high beam. Pull the lever toward you, to switch the headlights back to low beam.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 WINDSHIELD WIPERS AND WASHERS The wipers and washers are operated by a switch on the control lever. The lever is located on the right side of the steering column. Rotate the end of the lever to the first detent past the intermittent settings for low speed wiper operation, or to the second detent past the intermittent settings for high speed wiper operation.
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! (Continued) • Always remove any buildup of snow that prevents the windshield wiper blades from returning to the off position. If the windshield wiper control is turned off and the blades cannot return to the off position, damage to the wiper motor may occur. Intermittent Wiper System Use the intermittent wiper system when weather conditions make a single wiping cycle with a variable pause between cycles desirable.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 Mist Feature Push down on the wiper control lever to activate a single wipe to clear the windshield of road mist or spray from a passing vehicle. As long as the lever is held down, the wipers will continue to operate.
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Windshield Washers To use the washer, pull the windshield wiper/washer control lever toward you and hold it for as long as washer spray is desired. If you activate the washer while the wiper control is in the delay range, the wipers will operate in low speed for two wipe cycles after releasing the lever and then resume the intermittent interval previously selected.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 WARNING! Do not adjust the steering wheel while driving. The telescoping adjustment must be locked while driving. Adjusting the steering wheel while driving or driving without the telescoping adjustment locked could cause the driver to lose control of the vehicle. ELECTRONIC SPEED CONTROL — IF EQUIPPED When engaged, the Electronic Speed Control takes over the accelerator operation at speeds greater than 25 mph (40 km/h).
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Activate Push and release the ON/OFF button located on the end of the Electronic Speed Control lever. The CRUISE indicator in the instrument cluster will illuminate. To turn the system off, push and release the ON/OFF button a second time. The CRUISE indicator will turn off. Be sure to turn the system off when not in use. NOTE: The Electronic Speed Control system will automatically turn off when the ignition is turned OFF.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 To Resume Speed If you deactivated the Electronic Speed Control without erasing the set speed from memory and your vehicle speed is above 20 mph (32 km/h) you can resume the previous set speed. To do so, push the lever up and release RESUME ACCEL, and then remove your foot from the accelerator pedal. To Vary The Speed Setting When the Electronic Speed Control is set, you can increase speed by pushing up and holding the lever RESUME ACCEL.
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Accelerate For Passing Depress the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. The HomeLink威 buttons that are located in the headliner or sun visor designate the three different HomeLink威 channels. Using Electronic Speed Control On Hills NOTE: The Electronic Speed Control system maintains speed up and down hills. A slight speed change on moderate hills is normal.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 WARNING! • Your motorized door or gate will open and close while you are training the universal transceiver. Do not train the transceiver if people or pets are in the path of the door or gate. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by Federal safety standards. This includes most garage door opener models manufactured after 1982. Do not use a garage door opener without these safety features.
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Begin Programming 1. Turn the ignition switch to the ON/RUN position. 2. Hold the battery side of the handheld transmitter away from the HomeLink威 button you wish to program. Place the handheld transmitter 1 to 3 in (3 to 8 cm) away from the HomeLink威 button you wish to program while keeping the indicator light in view. 3.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 If the indicator light blinks rapidly for two seconds and then turns to a constant light, proceed to Step 5 “Programming A Rolling Code System.” 5. Programming A Rolling Code System At the garage door opener motor (in the garage), locate the “Learn” or “Training” button. 3 This can usually be found where the hanging antenna wire is attached to the garage door opener motor. It is NOT the button normally used to open and close the door.
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 6. Firmly press and release the “Learn” or “Training” button. The name and color of the button may vary by manufacturer. NOTE: There are 30 seconds in which to initiate the next step after the “Learn” button has been pressed. 7. Return to the vehicle and press the programmed HomeLink威 button twice (holding the button for two seconds each time). If the device is plugged in and activates, programming is complete.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 Gate Operator/Canadian Programming Canadian radio frequency laws require transmitter signals to time-out (or quit) after several seconds of transmission – which may not be long enough for HomeLink威 to pick up the signal during programming. Similar to this Canadian law, some U.S. gate operators are designed to time-out in the same manner.
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Troubleshooting Tips If you are having trouble programming HomeLink威, here are some of the most common solutions: • Replace the battery in the original transmitter. • Press the “Learn” button on the Garage Door Opener to complete the training for a Rolling Code. • Did you unplug the device for training, and remember to plug it back in? If you have any problems, or require assistance, please call toll-free 1–800–355–3515 or, on the Internet at www.HomeLink.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 POWER SUNROOF — IF EQUIPPED The sunroof controls are mounted between the sun visors in the Dome/Reading Lamp. Power Sunroof Switch 1 — Left Interior Light 2 — Power Sunroof Switch 3 — ATC Sensor (If Equipped) 4 — Right Interior Light WARNING! • Never leave children in a vehicle, with the keys in the ignition switch. Occupants, particularly unattended children, can become entrapped by the power sunroof while operating the power sunroof switch.
156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Sunroof Operation Opening Sunroof Manually Press the switch rearward and hold, and the sunroof will open automatically from any position. The sunroof will open fully, then stop automatically. During this operation, any release of the sunroof switch will stop the sunroof. Opening Sunroof - Express Press the switch rearward and release, and the sunroof will open automatically from any position. The sunroof will open fully, then stop automatically.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 Sunshade Operation The sunshade can be opened manually. However, the sunshade will open automatically as the sunroof opens. Sunroof Maintenance Use only a nonabrasive cleaner and a soft cloth to clean the glass panel. NOTE: The sunshade cannot be closed if the sunroof is open.
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ELECTRICAL POWER OUTLETS There are two 12-Volt electrical outlets on this vehicle. Both of the outlets are protected by a fuse. The instrument panel power outlet, located below the climate control knobs, has power available only when the ignition is ON. This outlet will also operate a conventional cigar lighter unit.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 The center console power outlet is powered directly from the battery (power available at all times). Items plugged into this outlet may discharge the battery and/or prevent engine starting. Console Interior WARNING! To avoid serious injury or death: • Do not use a three-prong adapter. • Do not insert any objects into the receptacles. • Do not touch with wet hands. • Close the lid when not in use and while driving the vehicle.
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting. • Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.) will degrade the battery even more quickly.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 CAUTION! For vehicles equipped with the heated and cooled cupholder, locate the cup holder ash receiver in the forward cupholder. When the unit is on and the LED is Red, the cup holder is being heated. When the LED is Blue, the cup holder is being cooled. 3 The optional ash receiver also comes with a cigar lighter.
162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Make sure the beverage container can withstand the temperatures shown above, when using the Cooled or Heated Cupholder. Rear Bottle Holders There are built-in bottle holders located in both rear door trim panels. Rear Bottle Holder WARNING! If containers of hot liquid are placed in the bottle holder, they can spill when the door is closed, burning the occupants. Be careful when closing the doors to avoid injury.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 STORAGE Driver’s Side Sunglass Holder — If Equipped An integrated sunglass holder is located in the headliner above the sun visor. To access the sunglass holder, lower the sun visor. Small items such as toll tickets can be stored between the two straps, while sunglasses or other items can be stored above the two straps.
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Cargo Area The 60/40 split-folding rear seat provides cargo-carrying versatility. The seatbacks fold down easily by pulling nylon tabs between the seatbacks and the bolsters. When the seats are folded down, they provide a continuous, nearly flat extension of the load floor. When the seatback is folded to the upright position, make sure it is latched by strongly pulling on the top of the seatback above the seat strap.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 Always place cargo evenly on the cargo floor. Put heavier objects as low and as far forward as possible. Place as much cargo as possible in front of the rear axle. Too much weight or improperly placed weight over or behind the rear axle can cause the rear of the vehicle to sway. accommodate large size cups and 20 oz. (.5 L) bottles. An optional removable ashtray may be located in the one cupholder.
166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Dual Storage Bins Lifting a latch at the front of the hinged armrest provides access to these storage areas.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 The left latch opens to the top storage area. The lower bin can be accessed directly, without first exposing the upper bin, by operating the right latch with the armrest down. The first storage bin can be used to hold smaller items. The lower storage bin includes a molded-in coin holder, room for CD’s, DVD’s, and a power outlet that allows a cell phone to recharge while concealed.
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Video Console — If Equipped The optional VES™ (Video Entertainment System) includes the following components: • The screen for a rear seat DVD player is stored under the armrest. • Remote Control • Audio/Video RCA Jacks Video Console Refer to, “Video Entertainment System — If Equipped,” in Section 4 of this manual, for further information.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 REAR WINDOW FEATURES Rear Window Defroster — If Equipped The electric rear window defroster switch is located on the climate control. Press this button to turn on the rear window defroster and the heated side mirrors (if equipped). An LED in the button will illuminate when the rear window defroster is on.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 Instrument Panel Features . . . . . . . . . . . . . . . . 174 䡵 Instrument Cluster – Base . . . . . . . . . . . . . . . . 175 ▫ Personal Settings (Customer-Programmable Features) . . . . . . . . . . . . . . . . . . . . . . . . . . . 196 䡵 Instrument Cluster – Premium . . . . . . . . . . . . 176 䡵 Setting The Analog Clock . . . . . . . . . . . . . . . . 199 䡵 Instrument Cluster Descriptions . . . . . . . . . . . .
172 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ List Button (Disc Mode For MP3/WMA Play) . . . . . . . . . 212 ▫ Info Button (Disc Mode For MP3/WMA Play) . . . . . . . . . 213 䡵 AM/FM/CD/DVD Multimedia System Radio (RER/REN) – If Equipped . . . . . . . . . . . . . . . . 215 ▫ Operating Instructions — Voice Recognition System (VR) — If Equipped . . . . . . . . . . . . . 215 ▫ Operating Instructions — Hands-Free Communication (UConnect威) — If Equipped . . 215 ▫ Notes On Playing MP3 Files . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 173 ▫ Electronic Serial Number/Sirius Identification Number (ESN/SID) . . . . . . . . . 239 ▫ Selecting Satellite Mode . . . . . . . . . . . . . . . . 240 ▫ Satellite Antenna . . . . . . . . . . . . . . . . . . . . . 240 ▫ Reception Quality . . . . . . . . . . . . . . . . . . . . 241 ▫ Operating Instructions — Satellite Mode . . . . 241 ▫ Operating Instructions — Hands-Free Phone (If Equipped) . . . . . . . . . . . . . . . . . . . . . . . .
174 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT PANEL FEATURES 1 - Air Outlet 2 - Side Window Demister Outlet 3 - Instrument Cluster 4 - Ignition Switch 5 - Analog Clock 6 - Radio 7 - Upper Glove Compartment/Beverage Cooler – If Equipped 8 - Lower Glove Compartment 9 - Heated Seat Switch – If Equipped 10 - Hazard Switch 11 - Storage Compartment 12 - Climate Control 13 - Trunk Release Switch
UNDERSTANDING YOUR INSTRUMENT PANEL 175 INSTRUMENT CLUSTER – BASE 4
176 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER – PREMIUM
UNDERSTANDING YOUR INSTRUMENT PANEL 177 INSTRUMENT CLUSTER DESCRIPTIONS 1. Fuel Gauge When the ignition switch is in the ON position, the pointer will show the level of fuel remaining in the fuel tank. 2. Fuel Door Reminder This is a reminder that the Fuel Filler Door is located on the left side of the vehicle. 3. Temperature Gauge The temperature gauge shows engine coolant temperature. Any reading below the red area of the gauge shows that the engine cooling system is operating properly.
178 UNDERSTANDING YOUR INSTRUMENT PANEL 5. Low Fuel Light When the fuel level drops to approximately 2.0 gallons (7.6 Liters), the fuel symbol will light and a single chime will sound. NOTE: This light will remain on until a minimum of approximately 3.0 gallons of fuel is added. 6. Charging System Light This light shows the status of the electrical charging system. The light should come on briefly when the ignition is first turned on and remain on briefly as a bulb check.
UNDERSTANDING YOUR INSTRUMENT PANEL 179 9. Seat Belt Reminder Light When the ignition switch is first turned ON, this light will come on for about six seconds. A chime will sound if you have not pulled the shoulder belt out of the retractor. This is a reminder to “buckle up”. If you do not buckle up, the light will remain on. 10. Oil Pressure Warning Light This light indicates low engine oil pressure.
180 UNDERSTANDING YOUR INSTRUMENT PANEL 14. Odometer/Trip Odometer The odometer shows the total distance the vehicle has been driven. U.S. federal regulations require that upon transfer of vehicle ownership, the seller certify to the purchaser the correct mileage that the vehicle has been driven. Therefore, if the odometer reading is changed during repair or replacement, be sure to keep a record of the reading before and after the service so that the correct mileage can be determined.
UNDERSTANDING YOUR INSTRUMENT PANEL 181 GASCAP If the vehicle diagnostic system detects a leak or change in the evaporative system, or the fuel filler cap is loose, improperly installed, or damaged, the words “GASCAP” will display in the odometer. If this occurs, tighten the fuel filler cap properly and press the odometer reset button to turn off the “GASCAP” message. (Refer to “Onboard Diagnostic System — OBDII” in Section 7 of this manual for more information).
182 UNDERSTANDING YOUR INSTRUMENT PANEL 4. For vehicles equipped with the Electronic Vehicle Information Center (EVIC), refer to “Electronic Vehicle Information Center (EVIC)” in this section of the manual. To reset the trip odometer, first set the display to Trip Mode. Then push and hold the button (approximately 2 seconds) until the display resets to 0 miles. The odometer must be in Trip Mode to reset the trip odometer. 15.
UNDERSTANDING YOUR INSTRUMENT PANEL 183 17. Electronic Throttle Control (ETC) Indicator Light This light informs you of a problem with the Electronic Throttle Control (ETC) system. If a problem is detected, the light will come on while the engine is running. If the light remains lit with the engine running your vehicle will usually be drivable and not need towing, however see your dealer for service as soon as possible.
184 UNDERSTANDING YOUR INSTRUMENT PANEL The dual brake system provides a reserve braking capacity in the event of a failure to a portion of the hydraulic system. Failure of either half of the dual brake system is indicated by the Brake Warning Light which will turn on when the brake fluid level in the master cylinder has dropped below a specified level. The light will remain on until the cause is corrected.
UNDERSTANDING YOUR INSTRUMENT PANEL 185 The light also will turn on when the parking brake is applied with the ignition switch in the ON position. NOTE: This light shows only that the parking brake is applied. It does not show the degree of brake application. 20. Turn Signal Indicators The arrows will flash in unison with the exterior turn signal, when using the turn signal lever. 21. Front Fog Light Indicator — If Equipped This light indicates when the front fog lights are ON. 22.
186 UNDERSTANDING YOUR INSTRUMENT PANEL If the ABS light is on, the brake system should be serviced as soon as possible to restore the benefit of Anti-Lock Brakes. The ABS warning light should be checked frequently to assure that it is operating properly. Turn the ignition key to the on position, but do not start the vehicle. The light should come on. If the light does not come on, have the system inspected by an authorized dealer. 24.
UNDERSTANDING YOUR INSTRUMENT PANEL 187 Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is combined with the low tire pressure telltale. When the system detects a malfunction, the telltale will flash for approximately one minute and then remain continuously illuminated. This sequence will continue upon subsequent vehicle start-ups as long as the malfunction exists.
188 UNDERSTANDING YOUR INSTRUMENT PANEL 25. Malfunction Indicator Light (MIL) The Malfunction Indicator Light (MIL) is part of an onboard diagnostic system called OBD that monitors emissions, engine, and automatic transaxle control systems. The light will illuminate when the key is in the ON position before engine start. If the bulb does not come on when turning the key from LOCK to ON, have the condition checked promptly. Certain conditions such as a loose or missing gas cap, poor fuel quality, etc.
UNDERSTANDING YOUR INSTRUMENT PANEL 189 ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) – IF EQUIPPED The Electronic Vehicle Information Center (EVIC) features a driver-interactive display that is located in the instrument cluster.
190 UNDERSTANDING YOUR INSTRUMENT PANEL The system allows the driver to select information by pressing the following buttons on the instrument panel switch bank: Press and release the MENU button to advance the display to Trip Functions or Personal settings or to return to the default System status MENU display. Press and release the COMPASS button to display the compass heading and the outside temperature. COMPASS Button Press and release the RESET button to accept a selection.
UNDERSTANDING YOUR INSTRUMENT PANEL 191 EVIC Displays When the appropriate conditions exist, the Electronic Vehicle Information Center (EVIC) displays the following messages.
192 UNDERSTANDING YOUR INSTRUMENT PANEL Unless reset, this message will continue to display each time you turn the ignition switch to the ON/RUN position. To turn off the message temporarily, press and release the MENU button. To reset the oil change indicator system (after performing the scheduled maintenance) perform the following procedure: 1. Turn the ignition switch to the ON position (Do not start the engine).
UNDERSTANDING YOUR INSTRUMENT PANEL 193 • Distance To Empty (DTE) Shows the estimated distance that can be traveled with the fuel remaining in the tank. This estimated distance is determined by a weighted average of the instantaneous and average fuel economy, according to the current fuel tank level. DTE cannot be reset through the RESET button. NOTE: Significant changes in driving style or vehicle loading will greatly affect the actual drivable distance of the vehicle, regardless of the DTE display value.
194 UNDERSTANDING YOUR INSTRUMENT PANEL Compass Display The compass heading indicates the direction the vehicle is facing. Press and release the compass button to display one of eight comCOM- pass heading and the outside temperature. PASS Button Automatic Compass Calibration This compass is self-calibrating, which eliminates the need to calibrate the compass manually. When the vehicle is new, the compass may appear erratic and the EVIC will flash the “CAL” indicator until the compass is calibrated.
UNDERSTANDING YOUR INSTRUMENT PANEL 195 Compass Variance Compass Variance is the difference between Magnetic North and Geographic North. To ensure compass accuracy, the compass variance should be properly set according to the variance map for the zone where the vehicle will be driven. When properly set, the compass will automatically account for this difference.
196 UNDERSTANDING YOUR INSTRUMENT PANEL 3. Press and release the STEP button until “Compass Variance” and the current Variance Value displays in the EVIC. 4. Press and release the RESET button to increment the Variance Value by one, (one button press per update), until the proper variance zone is selected according to the map. NOTE: The Variance Values will wrap around from 15 back to 1. The Default Variance is Zone 8. 5. Press and release the STEP button to exit.
UNDERSTANDING YOUR INSTRUMENT PANEL 197 Remote Key Unlock When “Driver Door 1st Press” is selected, only the driver’s door will unlock on the first press of the Remote Keyless Entry (RKE) transmitter UNLOCK button. When Driver Door 1st Press is selected, you must press of the RKE transmitter UNLOCK button twice to unlock the passenger’s doors. When “All Doors 1st Press” is selected, all of the doors will unlock on the first press of the RKE transmitter UNLOCK button.
198 UNDERSTANDING YOUR INSTRUMENT PANEL Headlights With Wipers (Available with Auto Headlights Only) When ON is selected, and the headlight switch is in the AUTO position, the headlights will turn on approximately 10 seconds after the wipers are turned on. The headlights will also turn off when the wipers are turned off if they were turned on by this feature. To make your selection, press and hold the RESET button until ON or OFF appears.
UNDERSTANDING YOUR INSTRUMENT PANEL 199 SETTING THE ANALOG CLOCK To set the analog clock, located at the top center of the instrument panel, press and hold the button in until the setting is correct. The clock will adjust slowly at first and then quicker the longer the button is held. 4 SALES CODE REQ — AM/FM STEREO RADIO AND 6–DISC CD/DVD CHANGER (MP3/WMA AUX JACK) Operating Instructions - Radio Mode NOTE: The radio sales code is located on the lower right side of the radio faceplate.
200 UNDERSTANDING YOUR INSTRUMENT PANEL Power Switch/Volume Control (Rotary) Push the ON/VOLUME control knob to turn on the radio. Press the ON/VOLUME control knob a second time to turn off the radio. Electronic Volume Control The electronic volume control turns continuously (360 degrees) in either direction without stopping. Turning the ON/VOLUME control knob to the right increases the volume and to the left decreases it.
UNDERSTANDING YOUR INSTRUMENT PANEL 201 Phone Button (UConnect威 Hands-Free Phone) — If Equipped Press this button to operate the Hands-Free Phone (UConnect威) feature (if equipped). Refer to “Hands-Free Communication (UConnect威)” in Section 3. If your vehicle is not equipped with or this feature is not available on your vehicle, a “Not Equipped With UConnect” message will display on the radio screen. TIME Button Press the TIME button and the time of day will display.
202 UNDERSTANDING YOUR INSTRUMENT PANEL RW/FF Pressing the RW (Rewind) or FF (Fast Forward) buttons causes the tuner to search for the next frequency in the direction of the arrows. This feature operates in AM, FM or Satellite (if equipped) frequencies. Push the rotary TUNE/SCROLL control knob a third time and TREBLE will display. Turn the TUNE/SCROLL control knob to the right or left to increase or decrease the treble tones.
UNDERSTANDING YOUR INSTRUMENT PANEL 203 MUSIC TYPE Button Pressing this button once will turn on the Music Type mode for five seconds. Pressing the MUSIC TYPE button or turning the TUNE/SCROLL control knob within five seconds will allow the program format type to be selected. Many radio stations do not currently broadcast Music Type information.
204 UNDERSTANDING YOUR INSTRUMENT PANEL Program Type Sports Talk Top 40 Weather 16-Digit Character Display Sports Talk Top 40 Weather By pressing the SEEK button when the Music Type icon is displayed, the radio will be tuned to the next frequency station with the same selected Music Type name. The Music Type function only operates when in the FM mode.
UNDERSTANDING YOUR INSTRUMENT PANEL 205 • Audio Stream – Repeatedly pressing SELECT will switch to different audio languages (if supported on the disc) (if equipped). • VES™ CH1/CH2 - Allows the user to change the mode of either the IR1 or IR2, wireless headphones by pressing the AUDIO/SELECT button (if equipped). • Angle – Repeatedly pressing SELECT will change the viewing angle if supported by the DVD disc (if equipped). • Set Home Clock - Pressing the SELECT button allows you to set the clock.
206 UNDERSTANDING YOUR INSTRUMENT PANEL Menu Language — If Equipped Selecting this item will allow the user to choose the default startup DVD menu language (effective only if language supported by disc). If you want to select a language not listed, then scroll down and select ⬙other.⬙ Enter the four-digit country code using the TUNE/ SCROLL control knob to scroll up and down to select the number and then push to select.
UNDERSTANDING YOUR INSTRUMENT PANEL 207 AutoPlay — If Equipped When this is set to On and a DVD video is inserted, it will bypass the DVD menu screen and automatically play the movie. In some rare cases, the DVD player may not auto-play the main title. In such cases, use the MENU button on the remote control to select desired title to play. NOTE: The user will have to set these defaults before loading a disc. If changes are made to these settings after a disc is loaded, changes will not be effective.
208 UNDERSTANDING YOUR INSTRUMENT PANEL Buttons 1 - 6 These buttons tune the radio to the stations that you commit to pushbutton memory {12 AM, 12 FM, and 12 Satellite (if equipped) stations}. DISC Button Pressing the DISC button will allow you to switch from AM/FM modes to Disc modes. Operation Instructions - (DISC MODE for CD and MP3/WMA Audio Play, DVD-VIDEO) The radio DVD player and many DVD discs are coded by geographic region. These region codes must match in order for the disc to play.
UNDERSTANDING YOUR INSTRUMENT PANEL 209 Radio display will show ⬙LOADING DISC⬙ when the disc is loading and “READING DISC” when the radio is reading the disc. CAUTION! This CD player will accept 4–3/4 in (12 cm) discs only. The use of other sized discs may damage the CD player mechanism. Eject Button — Ejecting Compact Disc(s) Press the EJECT button and the pushbutton with the corresponding number (1-6) where the CD was loaded and the disc will unload and move to the entrance for easy removal.
210 UNDERSTANDING YOUR INSTRUMENT PANEL RW/FF (CD MODE) Press and hold FF (Fast Forward) and the CD player will begin to fast forward until FF is released, or RW or another CD button is pressed. The RW (Rewind) button works in a similar manner. AM or FM Button (CD MODE) Switches the Radio into the AM or FM Radio mode. Notes On Playing MP3/WMA Files The radio can play MP3/WMA files; however, acceptable MP3/WMA file recording media and formats are limited.
UNDERSTANDING YOUR INSTRUMENT PANEL 211 Multisession disc formats are supported by the radio. Multisession discs may contain combinations of normal CD audio tracks and computer files (including MP3/ WMA files). Discs created with an option such as ⬙keep disc open after writing⬙ are most likely multisession discs. The use of multisession for CD audio or MP3/ WMA playback may result in longer disc loading times. frequencies in the following table are supported.
212 UNDERSTANDING YOUR INSTRUMENT PANEL ID3 Tag information for artist, song title, and album title are supported for ID3 version 1 tags. ID3 version 2 is not supported by the radios. Playlist files are not supported. MP3 Pro files are not supported. Playback of MP3/WMA Files When a medium containing MP3/WMA data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3/WMA files.
UNDERSTANDING YOUR INSTRUMENT PANEL 213 INFO Button (DISC Mode for MP3/WMA Play) Pressing the INFO button repeatedly will scroll through the following TAG information: Song Title, Artist, File Name, and Folder Name (if available). Press the INFO button once more to return to ⬙elapsed time⬙ priority mode. Press and hold the INFO button for three seconds or more and radio will display song titles for each file. Press and hold the INFO button again for three seconds to return to ⬙elapsed time⬙ display.
214 UNDERSTANDING YOUR INSTRUMENT PANEL TIME Button (Auxiliary Mode) Press the TIME button to change the display from elapsed playing time to time of day. The time of day will display for five seconds. Operating Instructions - Hands-Free Phone (UConnect威) (If Equipped) Refer to “Hands-Free Communication (UConnect威)” in Section 3. RW/FF (Auxiliary Mode) No function. Operating Instructions - Satellite Radio Mode (If Equipped) Refer to “Satellite Radio” in this section.
UNDERSTANDING YOUR INSTRUMENT PANEL 215 Macrovision This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only, unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited DTS™ ⬙DTS™⬙ and ⬙DTS™ 2.0⬙ are trademarks of Digital Theater Systems, Inc.
216 UNDERSTANDING YOUR INSTRUMENT PANEL Clock Setting Procedure Global Positioning System (GPS) — RER only The GPS receiver used in this system is synchronized to the time data being transmitted by the GPS satellite. The satellite clock is Greenwich Mean Time (GMT). This is the worldwide standard for time. This makes the system’s clock very accurate, once the appropriate time zone and daylight savings information is set. To Manually Set the Clock — RER/REN 1. Turn on the multimedia system. 2.
UNDERSTANDING YOUR INSTRUMENT PANEL 217 2. Touch the screen where the time is displayed. The clock setting menu will appear on the screen. Touch the screen where the words “Show Time if Radio is Off” are displayed to change the current setting. 3. When this feature is on, a check mark will appear in the box next to the words “Daylight Savings.” Touch the screen where the words “Daylight Savings” are displayed to change the current setting.
218 UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE RES — AM/FM STEREO RADIO WITH CD PLAYER (MP3 AUX JACK) NOTE: The radio sales code is located on the lower right side of the radio faceplate. Operating Instructions — Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Control (Rotary) Push the On/Volume control knob to turn on the radio. Push the On/Volume control knob a second time to turn off the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL 219 to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations without stopping, until you release it. TIME Button Press the TIME button and the time of day will display. In AM or FM mode, pressing the TIME button will switch between the time and frequency displays. Clock Setting Procedure 1. Press and hold the TIME button, until the hours blink. 2.
220 UNDERSTANDING YOUR INSTRUMENT PANEL Push the rotary Tune/Scroll control knob a second time and MID will display. Turn the Tune/Scroll control knob to the right or left to increase or decrease the mid-range tones. Push the rotary Tune/Scroll control knob a third time and TREBLE will display. Turn the Tune/Scroll control knob to the right or left to increase or decrease the treble tones. Push the rotary Tune/Scroll control knob a fourth time and BALANCE will display.
UNDERSTANDING YOUR INSTRUMENT PANEL 221 and 12 FM stations to be stored into pushbutton memory. The stations stored in SET 2 memory can be selected by pressing the pushbutton twice. Every time a preset button is used, a corresponding button number will display. Buttons 1 - 6 These buttons tune the radio to the stations that you commit to pushbutton memory (12 AM and 12 FM stations). DISC Button Pressing the DISC button will allow you to switch from AM/FM modes to Disc modes.
222 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! • This CD player will accept 4-3/4 in (12 cm) discs only. The use of other sized discs may damage the CD player mechanism. • Do not use adhesive labels. These labels can peel away and jam the player mechanism. • RES is a single CD player. Do not attempt to insert a second CD if one is already loaded. • Dual-media disc types (one side is a DVD, the other side is a CD) should not be used, and they can cause damage to the player.
UNDERSTANDING YOUR INSTRUMENT PANEL 223 RW/FF Press the RW button to stop the CD at the beginning of the current CD track/title. Press and hold the FF (Fast Forward) button and the CD player will begin to fast forward until FF is released, or RW or another CD button is pressed. The RW (Reverse) button works in a similar manner. AM/FM Button Press the button to select either AM or FM mode. SET/RND Button (Random Play Button) Press this button while the CD is playing to activate Random Play.
224 UNDERSTANDING YOUR INSTRUMENT PANEL The radio uses the following limits for file systems: • Maximum number of folder levels: 8 • Maximum number of files: 255 • Maximum number of folders. (The radio display of file names and folder names is limited. For large numbers of files and/or folders, the radio may be unable to display the file name and folder name, and will assign a number instead. With a maximum number of files, exceeding 20 folders will result in this display.
UNDERSTANDING YOUR INSTRUMENT PANEL 225 When using the MP3 encoder to compress audio data to an MP3 file, the bit rate and sampling frequencies in the following table are supported. In addition, variable bit rates (VBR) are also supported. The majority of MP3 files use a 44.1 kHz sampling rate and a 192, 160, 128, 96 or VBR bit rate. MPEG Specification MPEG-1 Audio Layer 3 MPEG-2 Audio Layer 3 Sampling Frequency (kHz) 48, 44.1, 32 24, 22.
226 UNDERSTANDING YOUR INSTRUMENT PANEL • Number of files and folders - Loading times will increase with more files and folders Pressing the DISC/AUX button will change the mode to auxiliary device if the AUX jack is connected. To increase the speed of disc loading, it is recommended to use CD-R media and single-session discs. To create a single-session disc, enable the “Disc at Once” option before writing to the disc. NOTE: The AUX device must be turned on and the device’s volume set to proper level.
UNDERSTANDING YOUR INSTRUMENT PANEL 227 SALES CODE RES/RSC — AM/FM STEREO RADIO WITH CD PLAYER (MP3 AUX JACK) AND SIRIUS RADIO NOTE: The radio sales code is located on the lower right side of the radio faceplate. Operating Instructions — Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Control (Rotary) Push the On/Volume control knob to turn on the radio. Push the On/Volume control knob a second time to turn off the radio.
228 UNDERSTANDING YOUR INSTRUMENT PANEL SEEK Buttons Press and release the SEEK buttons to search for the next listenable station in AM/FM mode. Press the right switch to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations without stopping until you release it. Voice Recognition System (Radio) — If Equipped Refer to “Voice Recognition System (VR)” in Section 3.
UNDERSTANDING YOUR INSTRUMENT PANEL 229 3. After adjusting the hours, press the right side Tune/ Scroll control knob to set the minutes. The minutes will begin to blink. 4. Adjust the minutes using the right side Tune/Scroll control knob. Press the Tune/Scroll control knob to save time change. 5. To exit, press any button/knob or wait five seconds. The clock can also be set by pressing the SETUP button.
230 UNDERSTANDING YOUR INSTRUMENT PANEL Push the rotary Tune/Scroll control knob a second time and MID will display. Turn the Tune/Scroll control knob to the right or left to increase or decrease the mid-range tones. Push the rotary Tune/Scroll control knob a third time and TREBLE will display. Turn the Tune/Scroll control knob to the right or left to increase or decrease the treble tones. Push the rotary Tune/Scroll control knob a fourth time and BALANCE will display.
UNDERSTANDING YOUR INSTRUMENT PANEL 231 Program Type Foreign Language Information Jazz News Nostalgia Oldies Personality Public Rhythm and Blues Religious Music Religious Talk Rock Soft Soft Rock Soft Rhythm and Blues 16-Digit Character Display Language Inform Jazz News Nostalga Oldies Persnlty Public R&B Rel Musc Rel Talk Rock Soft Soft Rck Soft R&B Program Type Sports Talk Top 40 Weather 16-Digit Character Display Sports Talk Top 40 Weather By pressing the SEEK button when the Music Type icon is disp
232 UNDERSTANDING YOUR INSTRUMENT PANEL SETUP Button Pressing the SETUP button allows you to select between the following items: • Set Clock — Pressing the SELECT button will allow you to set the clock. Turn the Tune/Scroll control knob to adjust the hours and then press and turn the Tune/Scroll control knob to adjust the minutes. Press the Tune/Scroll control knob again to save changes.
UNDERSTANDING YOUR INSTRUMENT PANEL 233 Operation Instructions — CD MODE for CD and MP3 Audio Play NOTE: • The ignition switch must be in the ON or ACC position to operate the radio. • This radio is capable of playing compact discs (CD), recordable compact discs (CD-R), rewritable compact discs (CD-RW), compact discs with MP3 tracks and multisession compact discs with CD and MP3 tracks. Inserting Compact Disc(s) Gently insert one CD into the CD player with the CD label facing up.
234 UNDERSTANDING YOUR INSTRUMENT PANEL EJECT Button - Ejecting a CD Press the EJECT button to eject the CD. If you have ejected a disc and have not removed it within 10 seconds, it will be reloaded. If the CD is not removed, the radio will reinsert the CD but will not play it. A disc can be ejected with the radio and ignition OFF. NOTE: Ejecting with ignition OFF is not allowed on convertible or soft-top models (if equipped). SEEK Button Press the right SEEK button for the next selection on the CD.
UNDERSTANDING YOUR INSTRUMENT PANEL 235 SET/RND Button (Random Play Button) Press this button while the CD is playing to activate Random Play. This feature plays the selections on the compact disc in random order to provide an interesting change of pace. Press the right SEEK button to move to the next randomly selected track. Press the SET/RND button a second time to stop Random Play.
236 UNDERSTANDING YOUR INSTRUMENT PANEL • Maximum number of characters in file/folder names: • Level 1: 12 (including a separator ⬙.⬙ and a threecharacter extension) • Level 2: 31 (including a separator ⬙.⬙ and a threecharacter extension) Multisession disc formats are supported by the radio. Multisession discs may contain combinations of normal CD audio tracks and computer files (including MP3 files). Discs created with an option such as ⬙keep disc open after writing⬙ are most likely multisession discs.
UNDERSTANDING YOUR INSTRUMENT PANEL 237 ID3 Tag information for artist, song title, and album title are supported for version 1 ID3 tags. ID3 version 2 is not supported by the radios. Playlist files are not supported. MP3 Pro files are not supported. Playback of MP3 Files When a medium containing MP3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3 files.
238 UNDERSTANDING YOUR INSTRUMENT PANEL INFO Button (CD Mode for MP3 Play) Pressing the INFO button repeatedly will scroll through the following TAG information: Song Title, Artist, File Name, and Folder Name (if available). Press the INFO button once more to return to ⬙elapsed time⬙ priority mode. Press and hold the INFO button for three seconds or more and the radio will display song titles for each file. Press and hold the INFO button again for three seconds to return to ⬙elapsed time⬙ display.
UNDERSTANDING YOUR INSTRUMENT PANEL 239 SATELLITE RADIO — IF EQUIPPED (REN/REQ/RER/RES/REU RADIOS ONLY) Satellite radio uses direct satellite-to-receiver broadcasting technology to provide clear digital sound, coast to coast. The subscription service provider is Sirius Satellite Radio. This service offers over 130 channels of music, sports, news, entertainment, and programming for children, directly from its satellites and broadcasting studios.
240 UNDERSTANDING YOUR INSTRUMENT PANEL To access the ESN/SID, refer to the following steps: ESN/SID Access With REQ/RES Radios With the ignition switch in the ON/RUN or ACC position and the radio on, press the SETUP button and scroll using the Tune/Scroll control knob until Sirius ID is selected. Press the Tune/Scroll control knob and the Sirius ID number will display. The Sirius ID number display will time out in two minutes. Press any button on the radio to exit this screen.
UNDERSTANDING YOUR INSTRUMENT PANEL 241 Reception Quality Satellite reception may be interrupted due to one of the following reasons: • The vehicle is parked in an underground parking structure or under a physical obstacle. • Dense tree coverage may interrupt reception in the form of short audio mutes. • Driving under wide bridges or along tall buildings can cause intermittent reception. • Placing objects over or too close to the antenna can cause signal blockage.
242 UNDERSTANDING YOUR INSTRUMENT PANEL INFO Button — Except REU Radio Pressing the INFO button will cycle the display information between Artist, Song Title, and Composer (if available). Also, pressing and holding the INFO button for an additional three seconds will make the radio display the Song Title all of the time (press and hold again to return to normal display). INFO Button — REU Radio Pressing the INFO button will display information about Artist, Song Title, and Composer (if available).
UNDERSTANDING YOUR INSTRUMENT PANEL 243 MUSIC TYPE Button — REU Radio Pressing this button provides a MUSIC TYPES list from which you can make a selection. Once a selection is made, you can seek up, or down, or scan the channels and the radio will tune to the next station matching the selected format. There is no time-out for this screen. Pressing the MUSIC TYPE button again will close the MUSIC TYPE screen. Once closed, seek up, seek down, and scan will no longer be based on your selection.
244 UNDERSTANDING YOUR INSTRUMENT PANEL Buttons 1 - 6 These buttons tune the radio to the channels that you commit to pushbutton memory (12 Satellite stations). Operating Instructions — Hands-Free Phone (If Equipped) Refer to “Hands-Free Communication (UConnect威)” in Section 3. • A diagonal 7 in (17.8 cm) Liquid Crystal Display (LCD) screen integrated into the center console armrest. The screen features brightness control for optimum daytime and nighttime viewing.
UNDERSTANDING YOUR INSTRUMENT PANEL 245 • The LCD screen swings up from the rear of the armrest to allow the rear seat passenger(s) to view the display. • The touch screen radio and DVD player controls allow front seat operation for easy setup in the case of younger rear seat passengers. • A battery-powered infrared remote control snaps into a molded compartment in the center console armrest upper storage bin.
246 UNDERSTANDING YOUR INSTRUMENT PANEL • Two wireless infrared headsets allow rear seat passengers to listen to the same or individual audio sources. Audio/Video RCA Jacks (AUX Jacks) on the rear of the center console enable the monitor to display video directly from a video camera, connect video games for display on the screen, or play music directly from an MP3 player. REMOTE SOUND SYSTEM CONTROLS — IF EQUIPPED The remote sound system controls are located on the rear surface of the steering wheel.
UNDERSTANDING YOUR INSTRUMENT PANEL 247 Right-Hand Switch Functions • Press the top of the switch to increase the volume. • Press the bottom of the switch to decrease the volume. • Press the button in the center of the switch to change modes (i.e., AM, FM, etc.). Left-Hand Switch Functions for Radio Operation • Press the top of the switch to SEEK the next listenable station up from the current setting. • Press the bottom of the switch to SEEK the next listenable station down from the current setting.
248 UNDERSTANDING YOUR INSTRUMENT PANEL CD/DVD MAINTENANCE To keep a CD/DVD in good condition, take the following precautions: 1. Handle the disc by its edge; avoid touching the surface. 2. If the disc is stained, clean the surface with a soft cloth, wiping from center to edge. 3. Do not apply paper or tape to the disc; avoid scratching the disc. 4. Do not use solvents such as benzene, thinner, cleaners, or antistatic sprays. 5. Store the disc in its case after playing. 6.
UNDERSTANDING YOUR INSTRUMENT PANEL 249 CLIMATE CONTROLS The Air Conditioning and Heating System is designed to make you comfortable in all types of weather. Manual Heating Ventilation and Air Conditioning (HVAC) Blower Control Rotate this control to regulate the amount of air forced through the ventilation system in any mode. The blower speed increases as you move the control to the right from the “O” (OFF) position. There are four blower speeds.
250 UNDERSTANDING YOUR INSTRUMENT PANEL Temperature Control Rotate this control to regulate the temperature of the air inside the passenger compartment. Rotating the dial left into the blue area of the scale indicates cooler temperatures while the rotating right into the red area indicates warmer temperatures. NOTE: If your air conditioning performance seems lower than expected, check the front of the A/C condenser located in front of the radiator for an accumulation of dirt or insects.
UNDERSTANDING YOUR INSTRUMENT PANEL 251 NOTE: For all settings except full cold or full hot, there is a difference in temperature between the upper and lower outlets. The warmer air flows to the floor outlets. This feature gives improved comfort during sunny but cool conditions. Defrost Air is directed through the windshield and side window demist outlets. Use this mode with maximum blower and temperature settings for best windshield and side window defrosting.
252 UNDERSTANDING YOUR INSTRUMENT PANEL Recirculation Control Pressing the Recirculation Control button will temporarily put the system in recirculation mode (ten minutes). This can be used when outside conditions such as smoke, odors, dust, or high humidity are present. Activating recirculation will cause the LED in the control button to illuminate. After ten minutes, the system will return to normal mode function and the LED will turn off.
UNDERSTANDING YOUR INSTRUMENT PANEL 253 NOTE: The air conditioning compressor will not engage until the engine has been running for about 10 seconds. Automatic Temperature Control (ATC) — If Equipped • MAX A/C For maximum cooling use the A/C and recirculation buttons at the same time. • ECONOMY MODE If economy mode is desired, press the A/C button to turn OFF the indicator light and the A/C compressor. Then, move the temperature control to the desired temperature.
254 UNDERSTANDING YOUR INSTRUMENT PANEL The controls on the climate control provide the system with operator input. Other sensors take account of vehicle speed, A/C pressure, outside temperature, and engine cooling temperature. Using all of these inputs, the system automatically adjusts airflow temperature, airflow distribution, airflow volume, and the amount of outside air recirculation. This maintains a comfortable temperature even under changing conditions. Operation of the system is quite simple. 1.
UNDERSTANDING YOUR INSTRUMENT PANEL 255 NOTE: • The temperature setting can be adjusted at anytime without affecting automatic operation. • Pressing the Air Conditioning Control button while in AUTO mode will cause the LED in the control button to flash three times and then turn off. This indicates that the system is in AUTO mode and requesting the air conditioning is not necessary.
256 UNDERSTANDING YOUR INSTRUMENT PANEL
UNDERSTANDING YOUR INSTRUMENT PANEL 257 The operator can override the AUTO mode setting to change airflow distribution by rotating the Mode Control knob (on the right) to one of the following positions. • Panel Air is directed through the outlets in the instrument panel. These outlets can be adjusted to direct airflow. NOTE: The center instrument panel outlets can be aimed so that they are directed toward the rear seat passengers for maximum airflow to the rear.
258 UNDERSTANDING YOUR INSTRUMENT PANEL • Air Conditioner Control Press this button to turn on the air conditioning during manual operation only. When the air conditioning is turned on, cool dehumidified air will flow through the outlets selected with the Mode control dial. Press this button a second time to turn OFF the air conditioning. An LED in the button illuminates when manual compressor operation is selected. • Recirculation Control The system will automatically control recirculation.
UNDERSTANDING YOUR INSTRUMENT PANEL 259 • Most of the time, when in Automatic Operation, you can temporarily put the system into Recirculation Mode by pressing the Recirculation Button. However, under certain conditions, while in Automatic Mode, the system is blowing air out the defrost vents. When these conditions are present, and the Recirculation Button is pressed, the indicator will flash and then turn off. This tells you that you are unable to go into recirculation mode at this time.
260 UNDERSTANDING YOUR INSTRUMENT PANEL Window Fogging Interior fogging on the windshield can be quickly removed by turning the mode selector to Defrost. The Defrost/Floor mode can be used to maintain a clear windshield and provide sufficient heating. If side window fogging becomes a problem, increase blower speed. Vehicle windows tend to fog on the inside in mild but rainy or humid weather. NOTE: Recirculate without A/C should not be used for long periods as fogging may occur.
UNDERSTANDING YOUR INSTRUMENT PANEL 261 Control Setting Suggestions for Various Weather Conditions 4
STARTING AND OPERATING CONTENTS 䡵 Starting Procedures . . . . . . . . . . . . . . . . . . . . 267 ▫ Brake/Transaxle Interlock System . . . . . . . . . 271 ▫ Normal Starting . . . . . . . . . . . . . . . . . . . . . 267 ▫ Automatic Transaxle Ignition Interlock System . . . . . . . . . . . . . . . . . . . . . . . . . . . . 272 ▫ Tip Start Feature . . . . . . . . . . . . . . . . . . . . . 268 ▫ 4 Speed/6 Speed Automatic Transaxle . . . . . . 272 ▫ Extremely Cold Weather (Below ⫺20°F Or ⫺29°C) . . . . . .
264 STARTING AND OPERATING ▫ Traction . . . . . . . . . . . . . . . . . . . . . . . . . . . 278 ▫ Brake Assist System (BAS) . . . . . . . . . . . . . . 292 䡵 Driving Through Water . . . . . . . . . . . . . . . . . . 279 ▫ Electronic Stability Program (ESP) . . . . . . . . . 293 ▫ Flowing/Rising Water . . . . . . . . . . . . . . . . . 279 䡵 Tire Safety Information . . . . . . . . . . . . . . . . . . 296 ▫ Shallow Standing Water . . . . . . . . . . . . . . . . 279 ▫ Tire Markings . . . . . . . . . . .
STARTING AND OPERATING 265 ▫ Tread Wear Indicators . . . . . . . . . . . . . . . . . 311 ▫ Reformulated Gasoline . . . . . . . . . . . . . . . . . 326 ▫ Life Of Tire . . . . . . . . . . . . . . . . . . . . . . . . . 312 ▫ Gasoline/Oxygenate Blends . . . . . . . . . . . . . 326 ▫ Replacement Tires . . . . . . . . . . . . . . . . . . . . 312 ▫ E-85 Usage In Non-Flex Fuel Vehicles . . . . . . 327 䡵 Tire Chains . . . . . . . . . . . . . . . . . . . . . . . . . . 314 ▫ MMT In Gasoline . . . . . . . . . .
266 STARTING AND OPERATING ▫ Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . 332 䡵 Trailer Towing . . . . . . . . . . . . . . . . . . . . . . . . 338 ▫ Cruising Range . . . . . . . . . . . . . . . . . . . . . . 333 ▫ Common Towing Definitions . . . . . . . . . . . . 338 ▫ Replacement Parts . . . . . . . . . . . . . . . . . . . . 333 ▫ Trailer Hitch Classification . . . . . . . . . . . . . . 340 ▫ Maintenance . . . . . . . . . . . . . . . . . . . . . . . .
STARTING AND OPERATING 267 STARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belt. Make sure all occupants have securely fastened their seat belts. WARNING! • Never leave children alone in a vehicle. Leaving children in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Do not leave the key in the ignition.
268 STARTING AND OPERATING Tip Start Feature Do not press the accelerator. Turn the ignition key briefly to START position, and release it. The starter motor will continue to run, and it will disengage automatically when the engine is running. If the engine fails to start, the starter will disengage automatically in 10 seconds. If this occurs, turn the ignition switch to the LOCK position, wait 10 to 15 seconds, then repeat the normal starting procedure.
STARTING AND OPERATING 269 If the engine fails to start after you have followed the “Normal Starting” or “Extreme Cold Weather” procedures, it may be flooded. To clear any excess fuel, push the accelerator pedal all the way to the floor and hold it. Then, turn the ignition switch to the START position and release it as soon as the starter engages. The starter motor will disengage automatically in 10 seconds.
270 STARTING AND OPERATING AUTOMATIC TRANSAXLE NOTE: You MUST press and hold the brake pedal down while shifting the shift lever out of PARK. CAUTION! Damage to the transaxle may occur if the following precautions are not observed: • Shift the shift lever into PARK only after the vehicle has come to a complete stop. • Shift the shift lever into or out of REVERSE only after the vehicle has come to a complete stop and the engine is at idle speed.
STARTING AND OPERATING 271 WARNING! (Continued) • Unintended movement of a vehicle could injure those in and near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, you should always shift the vehicle into PARK, remove the key from the ignition, and apply the parking brake. Once the key is removed from the ignition, the shift lever is locked in the PARK position, securing the vehicle against unwanted movement.
272 STARTING AND OPERATING NOTE: If this occurs, even if the override is successful, it is recommended that you visit a dealer at your earliest possible convenience. Your dealer has diagnostic equipment to determine if the problem could recur. Automatic Transaxle Ignition Interlock System This system prevents the key from being removed unless the shift lever is in PARK. It also prevents shifting out of PARK unless the key is in the ON position, and the brake pedal is applied.
STARTING AND OPERATING 273 Gear Ranges PARK Supplements the parking brake by locking the transaxle. The engine can be started in this range. Never attempt to use PARK while vehicle is in motion. Apply parking brake when leaving vehicle in this range. When parking on a flat surface, place the shift lever into the PARK position first, and then apply the parking brake.
274 STARTING AND OPERATING NEUTRAL Engine may be started in this range. WARNING! Do not coast in NEUTRAL and never turn off the ignition to coast down a hill. These are unsafe practices that limit your response to changing traffic or road conditions. You might lose control of the vehicle and have an accident. DRIVE – 6 Speed Transaxle This range should be used for most city and highway driving. It provides the smoothest upshifts, downshifts, and best fuel economy.
STARTING AND OPERATING 275 DRIVE 3 — 4 Speed Transaxle This range eliminates shifts into fourth gear. The transaxle will operate normally in first and second gear. Shifts into third gear may be delayed to provide second gear operation at higher speeds.
276 STARTING AND OPERATING In the event of a momentary problem, the transaxle can be reset to regain all forward gears by performing the following steps: 1. Stop the vehicle. 2. Shift the shift lever into PARK. 3. Turn the ignition switch to the LOCK position. 4. Restart the engine. 5. Shift the shift lever into the desired gear range and resume driving. NOTE: Even if the transaxle can be reset, it is recommended that you visit a dealer at your earliest possible convenience.
STARTING AND OPERATING 277 NOTE: In Autostick威 mode, the transaxle will only shift up or down when the driver moves the shift lever to the right (+) or left (-). AutoStick威 is deactivated when the shift lever is moved from the AutoStick (+/-) position into the DRIVE position. General Information • You can start out in 1st or 2nd gear. The system will ignore attempts to upshift at too low of a vehicle speed.
278 STARTING AND OPERATING DRIVING ON SLIPPERY SURFACES Acceleration Rapid acceleration on snow covered, wet, or other slippery surfaces may cause the front wheels to pull erratically to the right or left. This phenomenon occurs when there is a difference in the surface traction under the front (driving) wheels. WARNING! Rapid acceleration on slippery surfaces is dangerous. Unequal traction can cause sudden pulling of the front wheels. You could lose control of the vehicle and possibly have an accident.
STARTING AND OPERATING 279 DRIVING THROUGH WATER Driving through water more than a few inches/ centimeters deep will require extra caution to ensure safety and prevent damage to your vehicle. Flowing/Rising Water WARNING! Do not drive on or cross a road or a path where water is flowing and/or rising (as in storm run-off). Flowing water can wear away the road or path’s surface and cause your vehicle to sink into deeper water. Furthermore, flowing and/or rising water can carry your vehicle away swiftly.
280 STARTING AND OPERATING CAUTION! (Continued) WARNING! • Driving through standing water may cause damage to your vehicle’s drivetrain components. Always inspect your vehicle’s fluids (i.e., engine oil, transmission/transaxle, axle, etc.) for signs of contamination (i.e., fluid that is milky or foamy in appearance) after driving through standing water. Do not continue to operate the vehicle if any fluid appears contaminated, as this may result in further damage.
STARTING AND OPERATING 281 POWER STEERING The standard power steering system will give you good vehicle response and increased ease of maneuverability in tight spaces. The system will provide mechanical steering capability if power assist is lost. If for some reason the power assist is interrupted, it will still be possible to steer your vehicle. Under these conditions, you will observe a substantial increase in steering effort, especially at very low vehicle speeds and during parking maneuvers.
282 STARTING AND OPERATING Power Steering Fluid Check Checking the power steering fluid level at a defined service interval is not required. The fluid should only be checked if a leak is suspected, abnormal noises are apparent, and/or the system is not functioning as anticipated. Coordinate inspection efforts through an authorized dealer. No chemical flushes should be used in any power steering system; only the approved lubricant may be used.
STARTING AND OPERATING 283 When parking on a flat surface, place the shift lever in the PARK position first, and then apply the parking brake. When parking on a hill, it is important to apply the parking brake before placing the shift lever in PARK, otherwise the load on the transaxle locking mechanism may make it difficult to move the shift lever out of PARK. As an added precaution, turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade.
284 STARTING AND OPERATING • If the parking brake is applied while the vehicle is moving, a chime will sound to alert the driver. The chime will sound up to 10 times or until the vehicle has returned to a stop. The Brake System Warning Light in the instrument cluster will turn on when the parking brake is applied and the ignition switch is on. NOTE: This light only shows that the parking brake is applied. It does not show the degree of brake application.
STARTING AND OPERATING 285 BRAKE SYSTEM Your vehicle is equipped with dual hydraulic brake systems. If either of the two hydraulic systems loses normal capability, the remaining system will still function. However, there will be some loss of overall braking effectiveness. This will be evident by increased pedal travel during application and greater pedal force required to slow or stop the vehicle.
286 STARTING AND OPERATING Anti-Lock Brake System — If Equipped The Anti-Lock Brake System (ABS) provides increased vehicle stability and brake performance under most braking conditions. The system automatically “pumps” the brakes during severe braking conditions to prevent wheel lock-up. When the vehicle is driven over 7 mph (11 km/h), you may also hear a slight clicking sound as well as some related motor noises.
STARTING AND OPERATING 287 WARNING! (Continued) WARNING! (Continued) • Pumping of the Anti-Lock Brakes will diminish their effectiveness and may lead to an accident. Pumping makes the stopping distance longer. Just press firmly on your brake pedal when you need to slow down or stop.
288 STARTING AND OPERATING If the Anti-Lock Brake Light remains on or comes on while driving, it indicates that the Anti-Lock portion of the brake system is not functioning and that service is required. However, the conventional brake system will continue to operate normally if the Brake System Warning Light is not on. If the Anti-Lock Brake Light is on, the brake system should be serviced as soon as possible to restore the benefits of Anti-Lock brakes.
STARTING AND OPERATING 289 WARNING! (Continued) • The ABS cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded. • The ABS cannot prevent accidents, including those resulting from excessive speed in turns, following another vehicle too closely, or hydroplaning. Only a safe, attentive, and skillful driver can prevent accidents.
290 STARTING AND OPERATING If both the Brake Warning Light and the ABS Light remain on, the Anti-Lock brakes (ABS) and Electronic Brake Force Distribution (EBD) systems are not functioning. Immediate repair to the ABS system is required. See your authorized Dealer Service Center. • The ABS motor running (it may continue to run for a short time after the stop), When the vehicle is driven over 7 mph (11 km/h), you may also hear a slight clicking sound as well as some related motor noises.
STARTING AND OPERATING 291 All vehicle wheels and tires must be the same size and type and tires must be properly inflated to produce accurate signals for the computer. ELECTRONIC BRAKE CONTROL SYSTEM Your vehicle may be equipped with an optional advanced electronic brake control system that includes Anti-Lock Brake System (ABS), Traction Control System (TCS), Brake Assist System (BAS), and Electronic Stability Program (ESP).
292 STARTING AND OPERATING Brake Assist System (BAS) The BAS is designed to optimize the vehicle’s braking capability during emergency braking maneuvers. The system detects an emergency braking situation by sensing the rate and amount of brake application and then applies optimum pressure to the brakes. This can help reduce braking distances. The BAS complements the Anti-Lock Brake System (ABS). Applying the brakes very quickly results in the best BAS assistance.
STARTING AND OPERATING 293 Electronic Stability Program (ESP) This system enhances directional control and stability of the vehicle under various driving conditions. ESP corrects for over/under steering of the vehicle by applying the brake of the appropriate wheel to assist in counteracting the over/under steer condition. Engine power may also be reduced to help the vehicle maintain the desired path.
294 STARTING AND OPERATING WARNING! (Continued) • ESP cannot prevent accidents, including those resulting from excessive speed in turns, driving on very slippery surfaces, or hydroplaning. Only a safe, attentive, and skillful driver can prevent accidents. • The capabilities of an ESP-equipped vehicle must never be exploited in a reckless or dangerous manner, which could jeopardize the user’s safety or the safety of others. This mode should be used for almost all driving situations.
STARTING AND OPERATING 295 WARNING! In the Partial ESP mode, the engine torque reduction and stability features are desensitized. Therefore, the enhanced vehicle stability offered by ESP is unavailable. NOTE: To improve the vehicle’s traction when driving with snow chains, or starting off in deep snow, sand or gravel, it may be desirable to switch to the “Partial Off” mode by pressing the ESP switch.
296 STARTING AND OPERATING NOTE: • The ESP Indicator Light and the ESP/BAS Warning Light come on momentarily each time the ignition switch is turned ON. TIRE SAFETY INFORMATION Tire Markings • Each time the ignition is turned ON, the ESP System will be ON even if it was turned off previously. • The ESP Control System will make buzzing or clicking sounds when it is active. This is normal; the sounds will stop when ESP becomes inactive following the maneuver that caused the ESP activation. 1 — U.S.
STARTING AND OPERATING 297 NOTE: • P (Passenger) - Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designation. Example: P215/65R15 95H. • Temporary spare tires are high-pressure compact spares designed for temporary emergency use only. Tires designed to this standard have the letter “T” molded into the sidewall preceding the size designation. Example: T145/80D18 103M.
298 STARTING AND OPERATING Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ⴖ....blank....ⴖ = Passenger car tire based on European design standards LT = Light truck tire based on U.S. design standards T = Temporary spare tire 31 = Overall diameter in inches (in) 215 = Section width in millimeters (mm) 65 = Aspect ratio in percent (%) — Ratio of section height to section width of tire 10.
STARTING AND OPERATING 299 EXAMPLE: Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions — The maximum speed corresponding to the speed symbol should only be achieved under specified operating conditions (i.e.
300 STARTING AND OPERATING Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full TIN, including the date code, located on the white sidewall side of the tire. Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the outboard side, then you will find it on the inboard side of the tire.
STARTING AND OPERATING 301 Tire Loading and Tire Pressure Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar. Tire and Loading Information Placard This placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) total weight your vehicle can carry 3) tire size designed for your vehicle 4) cold tire inflation pressures for the front, rear, and spare tires.
302 STARTING AND OPERATING NOTE: Under a maximum loaded vehicle condition, gross axle weight ratings (GAWRs) for the front and rear axles must not be exceeded. For further information on GAWRs, vehicle loading, and trailer towing, refer to “Vehicle Loading” in this section. To determine the maximum loading conditions of your vehicle, locate the statement “The combined weight of occupants and cargo should never exceed XXX lbs or XXX kg” on the Tire and Loading Information placard.
STARTING AND OPERATING 303 6. If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle. NOTE: • The following table shows examples on how to calculate total load, cargo/luggage, and towing capacities of your vehicle with varying seating configurations and number and size of occupants.
304 STARTING AND OPERATING
STARTING AND OPERATING 305 WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.
306 STARTING AND OPERATING WARNING! (Continued) • Unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • Always drive with each tire inflated to the recommended cold tire inflation pressure. Economy Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement.
STARTING AND OPERATING 307 CAUTION! After inspecting or adjusting the tire pressure, always reinstall the valve stem cap (if equipped). This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressures specified on the placard are always “cold tire inflation pressure.” Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or driven less than 1 mile (1 km) after a 3 hour period.
308 STARTING AND OPERATING Tire Pressures for High Speed Operation The manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or conditions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressure is very important. Increased tire pressure and reduced vehicle loading may be required for high-speed vehicle operation.
STARTING AND OPERATING 309 Compact Spare Tire — If Equipped The compact spare is for temporary emergency use with radial tires. It is engineered to be used on your style vehicle only. Since this tire has limited tread life, the original tire should be repaired (or replaced) and reinstalled at the first opportunity. WARNING! Temporary use spare tires are for emergency use only. With these tires, do not drive more than 50 mph (80 km/h). Temporary-use spare tires have limited tread life.
310 STARTING AND OPERATING Limited Use Spare — If Equipped The limited use spare tire is for temporary emergency use on your vehicle. This tire is identified by a limited use spare tire warning label located on the limited use spare tire and wheel assembly. This tire may look like the original equipped tire on the front or rear axle of your vehicle, but it is not. Installation of this limited use spare tire affects vehicle handling.
STARTING AND OPERATING 311 Tire Spinning When stuck in mud, sand, snow, or ice conditions, do not spin your vehicle’s wheels faster than 30 mph (48 km/h) or for longer than 30 seconds continuously without stopping when you are stuck. Tread Wear Indicators Tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced. Refer to “Freeing A Stuck Vehicle” in Section 6 of this manual for additional information.
312 STARTING AND OPERATING These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes approximately 1/16 in (2 mm). When the tread is worn to the tread wear indicators, the tire should be replaced.
STARTING AND OPERATING 313 Information” placard for the size designation of your tire. The service description and load identification will be found on the original equipment tire. Failure to use equivalent replacement tires may adversely affect the safety, handling, and ride of your vehicle. We recommend that you contact your original equipment or an authorized tire dealer with any questions you may have on tire specifications or capability.
314 STARTING AND OPERATING WARNING! (Continued) CAUTION! • Failure to equip your vehicle with tires having adequate speed capability can result in sudden tire failure and loss of vehicle control. Damage to the vehicle may result if tire chains are used. CAUTION! Replacing original tires with tires of a different size may result in false speedometer and odometer readings. TIRE CHAINS Due to limited clearance, tire chains are not recommended.
STARTING AND OPERATING 315 TIRE ROTATION RECOMMENDATIONS Tires on the front and rear axles of vehicles operate at different loads and perform different steering, driving, and braking functions. For these reasons, they wear at unequal rates and tend to develop irregular wear patterns. These effects can be reduced by timely rotation of tires. The benefits of rotation are especially worthwhile with aggressive tread designs such as those on all season type tires.
316 STARTING AND OPERATING TIRE PRESSURE MONITOR SYSTEM (TPMS) • The Tire Pressure Monitor System (TPMS) will warn the driver of a low tire pressure based on the vehicle recommended cold placard pressure. • The tire pressure will vary with temperature by about 1 psi (7 kPa) for every 12 F (7 C). This means that when the outside temperature decreases, the tire pressure will decrease. Tire pressure should always be set based on cold inflation tire pressure.
STARTING AND OPERATING 317 once the system receives the updated tire pressures. The vehicle may need to be driven for up to 20 minutes above 15 mph (25 km/h) in order for the TPMS to receive this information. − For example, your vehicle may have a recommended cold (parked for more than three hours) placard pressure of 30 psi (207 kPa).
318 STARTING AND OPERATING NOTE: • The TPMS is not intended to replace normal tire care and maintenance, or to provide warning of a tire failure or condition. • The TPMS should not be used as a tire pressure gauge while adjusting your tire pressure. • Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability.
STARTING AND OPERATING 319 Tire Pressure Monitoring Low Pressure Warnings The Tire Pressure Monitoring Telltale Light will illuminate in the instrument cluster and a chime will sound when tire pressure is low in one or more of the four active road tires. Should this occur, you should stop as soon as possible, check the inflation pressure of each tire on your vehicle, and inflate each tire to the vehicle’s recommended cold placard pressure value.
320 STARTING AND OPERATING NOTE: 1. The compact spare tire (if so equipped) does not have a tire pressure monitoring sensor. Therefore, the TPMS will not monitor the pressure in the compact spare tire. 2. If you install the compact spare tire in place of a road tire that has a pressure below the low-pressure warning limit, upon the next ignition key cycle, a chime will sound and the TPM Telltale Light will turn ON. 3.
STARTING AND OPERATING 321 • Three Trigger Modules (mounted in three of the four wheel-wells) • Various Tire Pressure Monitoring System Messages, which display in the Electronic Vehicle Information Center (EVIC) • Tire Pressure Monitoring Telltale Light Tire Pressure Monitoring Low Pressure Warnings The Tire Pressure Monitoring Telltale Light will illuminate in the instrument cluster and a chime will sound when tire pressure is low in one or more of the four active road tires.
322 STARTING AND OPERATING Should this occur, you should stop as soon as possible, and inflate all tires with low pressure (those flashing in the EVIC graphic) to the vehicle’s recommended cold placard pressure value. Once the system receives the updated tire pressures, the system will automatically update, the graphic display in the EVIC will stop flashing, and the Tire Pressure Monitoring Telltale Light will turn off.
STARTING AND OPERATING 323 If the ignition key is cycled, this sequence will repeat, providing the system fault still exists. If the system fault no longer exists, the Tire Pressure Monitoring Telltale Light will no longer flash, and the ⬙CHECK TPM SYSTEM⬙ message will no longer display, and a pressure value will display in place of the dashes. A system fault can occur due to any of the following: 1.
324 STARTING AND OPERATING 4. For each subsequent ignition key cycle, a chime will sound, the TPM Telltale Light will flash on and off for 75 seconds and then remain on solid, and the EVIC will display a ⬙CHECK TPM SYSTEM⬙ message for three seconds and then display dashes (- -) in place of the pressure value. 5. Once you repair or replace the original road tire, and reinstall it on the vehicle in place of the compact spare, the TPMS will update automatically.
STARTING AND OPERATING 325 FUEL REQUIREMENTS 2.4L and 2.7L Engine The 2.4L and 2.7L engines are designed to meet all emission regulations and provide excellent fuel economy and performance when using high quality unleaded “regular” gasolines having an octane rating of 87. The use of premium gasoline is not recommended. Under normal conditions, the use of premium gasoline will not provide a benefit over high quality unleaded “regular” gasolines, and in some circumstances may result in poorer performance. 3.
326 STARTING AND OPERATING Over 40 automobile manufacturers around the world have issued and endorsed consistent gasoline specifications (the World Wide Fuel Charter, WWFC) which define fuel properties necessary to deliver enhanced emissions, engine performance, and durability for your vehicle. The manufacturer recommends the use of gasolines that meet the WWFC specifications if they are available.
STARTING AND OPERATING 327 Problems that result from using methanol/gasoline or E85 Ethanol blends are not the responsibility of the manufacturer. While MTBE is an oxygenate made from Methanol, it does not have the negative effects of Methanol. E-85 Usage In Non-Flex Fuel Vehicles Non-FFV vehicles are compatible with gasoline containing 10% ethanol (E10). Gasoline with higher ethanol content may void the vehicle’s warranty.
328 STARTING AND OPERATING of gasoline may not be indicated on the gasoline pump, therefore, you should ask your gasoline retailer whether or not his/her gasoline contains MMT. It is even more important to look for gasolines without MMT in Canada, because MMT can be used at levels higher than those allowed in the United States. Fuel System Cautions CAUTION! Follow these guidelines to maintain your vehicle’s performance: MMT is prohibited in Federal and California reformulated gasolines.
STARTING AND OPERATING 329 • The use of fuel additives, which are now being sold as octane enhancers, is not recommended. Most of these products contain high concentrations of methanol. Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsibility of the manufacturer. NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you.
330 STARTING AND OPERATING FLEXIBLE FUEL— 2.7L ONLY (EXCEPT CALIFORNIA EMISSION STATES) E-85 General Information The information in this section is for Flexible Fuel vehicles only. This section only covers those subjects that are unique to these vehicles. Please refer to the other sections of this manual for information on features that are common between Flexible Fuel and gasoline only powered vehicles. E-85 Fuel Cap CAUTION! Only vehicles with the special E-85 fuel filler cap can operate on E-85.
STARTING AND OPERATING 331 Along with the special E-85 fuel filler cap, your vehicle may display a badge, which also indicates it can operate on E-85. WARNING! Ethanol vapors are extremely flammable and could cause serious personal injury. Never have any smoking materials lit in or near the vehicle when removing the fuel filler tube cap (gas cap) or filling the tank. Do not use E-85 as a cleaning agent and never use it near an open flame.
332 STARTING AND OPERATING When you do switch fuel types it is recommended that: • you do not add less than 5 gal (19 L) when refueling • you drive the vehicle immediately after refueling for at least 5 miles (8 km) Observing these precautions will avoid possible hard starting and/or significant deterioration in drivability during warm up. NOTE: Use seasonally adjusted E-85 fuel (ASTM D5798).
STARTING AND OPERATING 333 Cruising Range Because E-85 fuel contains less energy per gallon than gasoline, you will experience an increase in fuel consumption. You can expect your fuel economy and driving range to decrease by about 30% compared to gasoline operation. Replacement Parts All components in your Flexible Fuel Vehicle (FFV) are designed to be compatible with ethanol. Always be sure that your vehicle is serviced with correct ethanol compatible parts.
334 STARTING AND OPERATING The gas cap is behind the fuel filler door, on the left rear quarter panel of the vehicle. If the gas cap is lost or damaged, be sure the replacement cap is for use with this vehicle. Fuel Filler Door After removing the gas cap, place the gas cap tether cable over a hook on the inside of the fuel door. This keeps the gas cap suspended away from and protects the vehicle’s surface.
STARTING AND OPERATING 335 CAUTION! WARNING! • Damage to the fuel system or emission control system could result from using an improper fuel tank filler tube cap (gas cap). • A poorly fitting gas cap could let impurities into the fuel system and could cause the • A poorly fitting gas cap may cause the Malfunction Indicator Light to turn on. • To avoid fuel spillage and overfilling, do not “top off” the fuel tank after filling. When the fuel nozzle “clicks” or shuts off, the fuel tank is full.
336 STARTING AND OPERATING NOTE: • Tighten the gas cap until you hear a “clicking” sound. This is an indication that the gas cap is tightened properly. The Malfunction Indicator Light in the instrument cluster may turn on if the gas cap is not secured properly. Make sure that the gas cap is tightened each time the vehicle is refueled. • When the fuel nozzle “clicks” or shuts off, the fuel tank is full.
STARTING AND OPERATING 337 • Type of Vehicle • Month Day and Hour of Manufacture (MDH) The bar code allows a computer scanner to read the Vehicle Identification Number (VIN). Gross Vehicle Weight Rating (GVWR) The GVWR is the total allowable weight of your vehicle. This includes driver, passengers, and cargo. The total load must be limited so that you do not exceed the GVWR. Gross Axle Weight Rating (GAWR) The GAWR is the maximum capacity of the front and rear axles.
338 STARTING AND OPERATING Figure out the weight on the front and rear of the vehicle separately. It is important that you distribute the load evenly over the front and rear axles. Overloading can cause potential safety hazards and shorten useful service life. Heavier axles or suspension components do not necessarily increase the vehicle’s GVWR. Loading To load your vehicle properly, first figure out its empty weight, axle by axle and side by side.
STARTING AND OPERATING 339 Gross Vehicle Weight Rating (GVWR) The GVWR is the total allowable weight of your vehicle. This includes driver, passengers, cargo, and tongue weight. The total load must be limited so that you do not exceed the GVWR. Gross Trailer Weight (GTW) The GTW is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or temporary) loaded in or on the trailer in its ⬙loaded and ready for operation⬙ condition.
340 STARTING AND OPERATING Frontal Area The frontal area is the maximum height and maximum width of the front of a trailer and its cargo. Weight-Carrying Hitch A weight-carrying hitch supports the trailer tongue weight, just as if it were luggage located at a hitch ball or some other connecting point of the truck. These kinds of hitches are the most popular on the market today and they’re commonly used to tow small- and medium-sized trailers.
STARTING AND OPERATING 341 Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. Maximum Trailer Weight Ratings Max. GTW Engine/Transaxle Max. Frontal Area (Gross Trailer Wt.) 2.4L/Auto See Note 2 1,000 lbs (450 kg) 2.7L/Auto See Note 2 1,500 lbs (680 kg) 3.5L/Auto 22 sq.ft. (2.0 sq.m) 2,000 lbs (900 kg) Refer to local laws for maximum trailer towing speeds.
342 STARTING AND OPERATING CAUTION! Towing a trailer with a larger than recommended frontal area could cause the engine to overheat or cause severe engine damage under extreme conditions. Trailer and Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% of the Gross Trailer Weight (GTW) on the tow hitch of your vehicle.
STARTING AND OPERATING 343 NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options, or authorized dealer-installed options, must be considered as part of the total load on your vehicle. Refer to the Tire and Loading Information placard in the Tire Safety Information section of this manual for the maximum combined weight of occupants and cargo for your vehicle.
344 STARTING AND OPERATING WARNING! • Improper towing can lead to an injury accident. Follow these guidelines to make your trailer towing as safe as possible: • Make certain that the load is secured in the trailer and that it will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control. You could lose control of your vehicle and have an accident.
STARTING AND OPERATING 345 4. Trailer tongue weight rating for the trailer hitch utilized (This requirement may limit the ability to always achieve 10% of trailer tongue weight as a percentage of total trailer weight). Towing Requirements — Tires • Do not attempt to tow a trailer while using a compact spare tire. • Proper tire inflation pressures are essential to the safe and satisfactory operation of your vehicle.
346 STARTING AND OPERATING CAUTION! WARNING! (Continued) If the trailer weighs more than 1,000 lbs (450 kg) loaded, it should have its own brakes with adequate braking capacity. Failure to do this could lead to accelerated brake lining wear, higher brake pedal effort, and longer stopping distances. • Towing any trailer will increase your stopping distance. When towing, you should allow for additional space between your vehicle and the vehicle in front of you.
STARTING AND OPERATING 347 Automatic Transaxle The DRIVE range can be selected when towing. However, if frequent shifting occurs while in this range, third gear for a four-speed automatic and the fifth gear for a six-speed AutoStick威 should be selected. NOTE: Check the four-speed automatic transaxle fluid level before towing. AutoStick威 six—speed transmission is sealed and the fluid level cannot be checked. See your authorized dealership service center for assistance.
348 STARTING AND OPERATING Cooling System To reduce potential for engine and transaxle overheating, take the following actions: • City Driving When stopped for short periods of time, put transaxle in neutral and increase engine idle speed. • Highway Driving Reduce speed. • Air Conditioning Turn off temporarily. RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) Towing This Vehicle Behind Another Vehicle (Flat towing with all four wheels on the ground) CAUTION! DO NOT flat tow this vehicle.
WHAT TO DO IN EMERGENCIES CONTENTS 䡵 Hazard Warning Flasher . . . . . . . . . . . . . . . . . 350 䡵 Jump-Starting Procedure . . . . . . . . . . . . . . . . . 360 䡵 If Your Engine Overheats . . . . . . . . . . . . . . . . 350 䡵 Freeing A Stuck Vehicle . . . . . . . . . . . . . . . . . 363 ▫ Engine Oil Overheating (2.4L Engine Only) — If Equipped. . . . . . . . . . . . . . . . . . . . . . . 352 䡵 Towing A Disabled Vehicle . . . . . . . . . . . . . . . 364 䡵 Jacking And Tire Changing . . . . . . . . . .
350 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER The Hazard Warning flasher switch is located on the instrument panel, below the radio. Press the switch to turn on the Hazard Warning flashers. When the Hazard Warning flasher switch is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency. Press the switch a second time to turn off flashers. This is an emergency warning system and should not be used when the vehicle is in motion.
WHAT TO DO IN EMERGENCIES 351 NOTE: There are steps that you can take to slow down an impending overheat condition. If your air conditioner is on, turn it off. The air conditioning system adds heat to the engine cooling system and turning off the A/C removes this heat. You can also turn the temperature control to maximum heat, the mode control to floor, and the fan control to high. This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.
352 WHAT TO DO IN EMERGENCIES WARNING! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call a service center if your vehicle overheats. If you decide to look under the hood yourself, refer to Section 7, Maintenance, of this manual. Follow the warnings under the Cooling System Pressure Cap paragraph. Engine Oil Overheating (2.
WHAT TO DO IN EMERGENCIES 353 WARNING! (Continued) • The jack is designed to use as a tool for changing tires only. The jack should not be used to lift the vehicle for service purposes. The vehicle should be jacked on a firm level surface only. Avoid ice or slippery areas. Spare Tire Removal Lift up the load floor cover and remove the hold down. Jack Location The jack and jack-handle are stowed under the load floor in the trunk.
354 WHAT TO DO IN EMERGENCIES Preparations For Jacking 4. Turn OFF the ignition. 1. Park the vehicle on a firm level surface. Avoid ice or slippery areas. 5. Turn on the Hazard Warning Flasher. WARNING! Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. 2. Set the parking brake. 3.
WHAT TO DO IN EMERGENCIES 355 Jacking Instructions WARNING! (Continued) WARNING! Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: • Always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle. • Block the wheel diagonally opposite the wheel to be raised. • Set the parking brake firmly and set an automatic transmission in PARK; a manual transmission in REVERSE.
356 WHAT TO DO IN EMERGENCIES 1. Remove the scissors jack and lug wrench from the spare wheel as an assembly. Turn the jack screw to the left to loosen the lug wrench, and remove the wrench from the jack assembly. NOTE: The jack handle attaches to the side of the jack with two attachment points. When the jack is partially expanded, the tension between the two attachment points holds the jack handle in place. Removing Jack Handle From Jack 2.
WHAT TO DO IN EMERGENCIES 357 6 Jacking Locations
358 WHAT TO DO IN EMERGENCIES CAUTION! WARNING! Do not attempt to raise the vehicle by jacking on locations other than those indicated in step 3. Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 3. There are two front jacking locations and two rear jacking locations on each side of the body (as pictured above). 4.
WHAT TO DO IN EMERGENCIES 359 WARNING! WARNING! To avoid possible personal injury, handle the wheel covers with care to avoid contact with any sharp edges. A loose tire or jack thrown forward in a collision or hard stop could endanger the occupants of the vehicle. Always stow the jack parts and the spare tire in the places provided. 7. Lower the vehicle by turning the jack screw to the left. 8. Finish tightening the nuts. Push down on the wrench while tightening the wheel nuts.
360 WHAT TO DO IN EMERGENCIES JUMP-STARTING PROCEDURE The battery is stored between the left front headlight assembly and the left front wheel splash shield. Access is through the splash shield. Jump-starting remote battery terminals are located under the hood. WARNING! • Take care to avoid the radiator cooling fan whenever the hood is raised. It can start anytime the ignition switch is on. You can be hurt by the fan.
WHAT TO DO IN EMERGENCIES 361 2. When boosting from a battery in another vehicle, park that vehicle within booster cable reach, but without allowing the vehicles to touch. Set the parking brake, place the automatic transaxle in PARK and turn ignition to LOCK for both vehicles. 5. Connect the other cable, first to the negative terminal of the booster battery and then to the engine ground (-) of the vehicle with the discharged battery. Make sure you have a good contact on the engine ground.
362 WHAT TO DO IN EMERGENCIES 6. If the vehicle is equipped with Sentry Key威 Immobilizer, turn the ignition switch to the ON position for three seconds before moving the ignition switch to the START position. 7. Start the engine in the vehicle that has the booster battery, let the engine idle a few minutes, and then start the engine in the vehicle with the discharged battery. 8. When removing the jumper cables, reverse the sequence exactly. Be careful of the moving belts and fan. 9.
WHAT TO DO IN EMERGENCIES 363 WARNING! Any procedure other than above could result in: • Personal injury caused by electrolyte squirting out the battery vent; • Personal injury or property damage due to battery explosion; • Damage to charging system of booster vehicle or of immobilized vehicle. FREEING A STUCK VEHICLE If your vehicle becomes stuck in mud, sand, or snow, it can often be moved by a rocking motion. Turn your steering wheel right and left to clear the area around the front wheels.
364 WHAT TO DO IN EMERGENCIES CAUTION! Racing the engine or spinning the wheels too fast may lead to transaxle overheating and failure. It can also damage the tires. Do not spin the wheels above 30 mph (48 km/h). Do not spin the wheels continuously for more than 30 seconds.
WHAT TO DO IN EMERGENCIES 365 Towing Without The Ignition Key Special care must be taken when the vehicle is towed with the ignition in the LOCK position. Flatbed towing is the preferred towing method. However, if a flatbed towing vehicle is not available, a wheel lift towing vehicle may be used. Rear towing is not recommended with the front wheels on the ground, as transaxle damage can result. If rear towing is the only alternative, a front end dolly must be used.
366 WHAT TO DO IN EMERGENCIES Battery power is required to release the brake/transaxle interlock system. There is an override system that allows you to shift out of PARK in case of loss of power. To activate the override system: • Insert a key, screwdriver, or similar object into the front hole then push and hold the manual override release lever forward. • Firmly apply the parking brake. • While holding the release lever forward, move the shift lever from PARK to NEUTRAL.
MAINTAINING YOUR VEHICLE CONTENTS 䡵 Engine Compartment — 2.4L . . . . . . . . . . . . . 369 䡵 Maintenance Procedures . . . . . . . . . . . . . . . . . 375 䡵 Engine Compartment — 2.7L . . . . . . . . . . . . . 370 ▫ Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . 375 䡵 Engine Compartment — 3.5L . . . . . . . . . . . . . 371 ▫ Engine Oil Filter . . . . . . . . . . . . . . . . . . . . . 379 䡵 Onboard Diagnostic System — OBD II . . . . . . . 372 ▫ Engine Air Cleaner Filter . . . . . . . . .
368 MAINTAINING YOUR VEHICLE ▫ Adding Washer Fluid . . . . . . . . . . . . . . . . . . 385 䡵 Bulb Replacement . . . . . . . . . . . . . . . . . . . . . 411 ▫ Exhaust System . . . . . . . . . . . . . . . . . . . . . . 385 ▫ Headlight . . . . . . . . . . . . . . . . . . . . . . . . . . 411 ▫ Cooling System . . . . . . . . . . . . . . . . . . . . . . 388 ▫ Front Turn Signal/Parking Light . . . . . . . . . . 413 ▫ Brake System . . . . . . . . . . . . . . . . . . . . . . . 394 ▫ Front Fog Light . . . . .
MAINTAINING YOUR VEHICLE 369 ENGINE COMPARTMENT — 2.
370 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT — 2.
MAINTAINING YOUR VEHICLE 371 ENGINE COMPARTMENT — 3.
372 MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated Onboard Diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transaxle control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as maintaining engine emissions well within current government regulations.
MAINTAINING YOUR VEHICLE 373 the gas cap is properly tightened. Press the trip odometer “Reset” button to turn off the message. If the problem persists, the message will appear the next time the vehicle is started. This might indicate a damaged cap. If the problem is detected twice in a row, the system will turn on the “Malfunction Indicator Light (MIL).” Resolving the problem will turn the MIL light off.
374 MAINTAINING YOUR VEHICLE 5. Approximately 15 seconds later, one of two things will happen: a. The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine. This means that your vehicle’s OBD II system is not ready and you should not proceed to the I/M station. b. The MIL will not flash at all and will remain fully illuminated until you turn OFF the ignition or start the engine.
MAINTAINING YOUR VEHICLE 375 DEALER SERVICE Your authorized dealer has the qualified service personnel, special tools, and equipment to perform all service operations in an expert manner. Service Manuals are available which include detailed service information for your vehicle. Refer to these manuals before attempting any procedure yourself. NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you.
376 MAINTAINING YOUR VEHICLE The best time to check the engine oil level is about 5 minutes after a fully warmed engine is shut off. Do not check oil level before starting the engine after it has sat overnight. Checking engine oil level when the engine is cold will give you an incorrect reading. Checking the oil while the vehicle is on level ground and only when the engine is hot, will improve the accuracy of the oil level readings. Maintain the oil level between the range markings on the dipstick.
MAINTAINING YOUR VEHICLE 377 Engine Oil Selection For best performance and maximum protection under all types of operating conditions, the manufacturer recommends engine oils that are API Certified and meet the requirements of Chrysler Material Standard MS-6395. American Petroleum Institute (API) Engine Oil Identification Symbol This symbol means that the oil has been certified by the American Petroleum Institute (API). The manufacturer only recommends API Certified engine oils.
378 MAINTAINING YOUR VEHICLE Engine Oil Viscosity (SAE Grade) — 3.5L Engine SAE 10W-30 engine oil is preferred for all operating temperatures. The engine oil filler cap also shows the recommended engine oil viscosity for your vehicle. Lubricants which do not have both, the engine oil certification mark and the correct SAE viscosity grade number should not be used. The engine oil filler cap also shows the recommended engine oil viscosity for your engine.
MAINTAINING YOUR VEHICLE 379 station, or governmental agency for advice on how and where used oil and oil filters can be safely discarded in your area. Engine Oil Filter The engine oil filter should be replaced at every engine oil change. Engine Oil Filter Selection All of this manufacturer’s engines have a full-flow type disposable oil filter. Use a filter of this type for replacement. The quality of replacement filters varies considerably.
380 MAINTAINING YOUR VEHICLE Engine Air Cleaner Filter Selection The quality of replacement engine air cleaner filters varies considerably. Only high quality filters should be used to assure most efficient service. MOPAR威 engine air cleaner filters are high quality and are recommended. Maintenance-Free Battery You will never have to add water, nor is periodic maintenance required.
MAINTAINING YOUR VEHICLE 381 CAUTION! • It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked positive (+) and negative (-) and identified on the battery case. Cable clamps should be tight on the terminal posts and free of corrosion. Apply grease to posts and clamps after tightening.
382 MAINTAINING YOUR VEHICLE Refrigerant Recovery and Recycling R-134a air conditioning refrigerant is a hydrofluorocarbon (HFC) that is endorsed by the Environmental Protection Agency and is an ozone-saving product. However, the manufacturer recommends that air conditioning service be performed by authorized dealers or other service facilities using recovery and recycling equipment. The A/C Air Filter is located in the fresh air inlet behind the glove box.
MAINTAINING YOUR VEHICLE 383 4. Pivot the glove box downward. 5. Disengage the two retaining tabs that secure the filter cover to the HVAC housing and remove the cover. 6. Remove the A/C Air Filter by pulling it straight out of the housing. 7. Install the A/C Air Filter with the arrow on the filter pointing toward the floor. When installing the filter cover, make sure the retaining tabs fully engage the cover.
384 MAINTAINING YOUR VEHICLE Body Lubrication Locks and all body pivot points, including such items as seat tracks, door hinge pivot points and rollers, liftgate, tailgate, sliding doors and hood hinges, should be lubricated periodically with a lithium based grease such as MOPAR威 Spray White Lube to assure quiet, easy operation and to protect against rust and wear.
MAINTAINING YOUR VEHICLE 385 NOTE: Always refer to the wiper blade packaging for specific installation instructions. Many wiper blade replacements fit multiple vehicles. Adding Washer Fluid The fluid reservoir for the windshield washers is located in the engine compartment. Be sure to check the fluid level in the reservoir at regular intervals. Fill the reservoir with windshield washer solvent (not radiator antifreeze) and operate the system for a few seconds to flush out the residual water.
386 MAINTAINING YOUR VEHICLE WARNING! CAUTION! Exhaust gases can injure or kill. They contain carbon monoxide (CO) which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing CO, refer to Exhaust Gas in the Safety Tips section of this manual. Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition.
MAINTAINING YOUR VEHICLE 387 WARNING! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your exhaust system. Do not park or operate your vehicle in areas where your exhaust system can contact anything that can burn. In unusual situations involving grossly malfunctioning engine operation, a scorching odor may suggest severe and abnormal catalyst overheating.
388 MAINTAINING YOUR VEHICLE Cooling System WARNING! • When working near the radiator cooling fan, disconnect the fan motor lead or turn the ignition switch to the LOCK position. The fan is temperature controlled and can start at anytime the ignition switch is in the ON position. • You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator. If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.
MAINTAINING YOUR VEHICLE 389 Selection Of Coolant Use only the manufacturer’s recommended coolant. Refer to “Fluids, Lubricants, and Genuine Parts” in this section for the correct fluid type. CAUTION! • Mixing of engine coolant (antifreeze) other than specified HOAT engine coolant (antifreeze), may result in engine damage and may decrease corrosion protection.
390 MAINTAINING YOUR VEHICLE Adding Coolant Your vehicle has been built with an improved engine coolant (antifreeze) that allows extended maintenance intervals. This engine coolant (antifreeze) can be used up to 5 Years or 102,000 miles (170 000 km) before replacement. To prevent reducing this extended maintenance period, it is important that you use the same engine coolant (antifreeze) throughout the life of your vehicle.
MAINTAINING YOUR VEHICLE 391 Cooling System Pressure Cap The cap must be fully tightened to prevent loss of engine coolant (antifreeze), and to ensure that engine coolant (antifreeze) will return to the radiator from the coolant recovery bottle. The cap should be inspected and cleaned if there is any accumulation of foreign material on the sealing surfaces. WARNING! • The warning words “DO NOT OPEN HOT” on the cooling system pressure cap are a safety precaution.
392 MAINTAINING YOUR VEHICLE Disposal of Used Engine Coolant Used ethylene glycol based engine coolant (antifreeze) is a regulated substance requiring proper disposal. Check with your local authorities to determine the disposal rules for your community. To prevent ingestion by animals or children, do not store ethylene glycol based engine coolant (antifreeze) in open containers or allow it to remain in puddles on the ground. If ingested by a child, contact a physician immediately.
MAINTAINING YOUR VEHICLE 393 humidity accumulating on the radiator and being vaporized when the thermostat opens, allowing hot engine coolant (antifreeze) to enter the radiator. If an examination of your engine compartment shows no evidence of radiator or hose leaks, the vehicle may be safely driven. The vapor will soon dissipate. • Do not overfill the coolant recovery bottle. • Check engine coolant (antifreeze) freeze point in the radiator and in the coolant recovery bottle.
394 MAINTAINING YOUR VEHICLE Brake System In order to assure brake system performance, all brake system components should be inspected periodically. Refer to the “Maintenance Schedule” in Section 8 of this manual for the proper maintenance intervals. WARNING! Riding the brakes can lead to brake failure and possibly an accident. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage.
MAINTAINING YOUR VEHICLE 395 WARNING! CAUTION! • Overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts and the brake fluid catching fire. • Use of a brake fluid that has a lower initial boiling point than the recommended MOPAR威 DOT 3 product or a brake fluid that is unidentified as to FMVSS specification may result in sudden brake failure during hard prolonged braking. You could have an accident.
396 MAINTAINING YOUR VEHICLE Fluid Level Check — Vehicles with 2.4L and 2.7L Engines Use the following procedure to check the automatic transaxle fluid level properly: 1. Park the vehicle on level ground. 2. Run the engine at curb idle speed for a minimum of 60 seconds. 3. Apply the parking brake fully. 4. Place the gear selector momentarily in each gear position ending with the lever in PARK. 5. Wipe the area around the dipstick clean to eliminate the possibility of dirt entering the transaxle. 6.
MAINTAINING YOUR VEHICLE 397 CAUTION! • Using a transmission fluid other than the manufacturer’s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder. Using a transmission fluid other than that recommended by the manufacturer will result in more frequent fluid and filter changes. Refer to “Fluids, Lubricants, and Genuine Parts” for the correct fluid type. • Dirt and water in the transaxle can cause serious damage.
398 MAINTAINING YOUR VEHICLE Appearance Care And Protection From Corrosion Protection of Body and Paint from Corrosion Vehicle body care requirements vary according to geographic locations and usage. Chemicals that make roads passable in snow and ice and those that are sprayed on trees and road surfaces during other seasons are highly corrosive to the metal in your vehicle.
MAINTAINING YOUR VEHICLE 399 Washing • Wash your vehicle regularly. Always wash your vehicle in the shade using MOPAR威 Car Wash or a mild car wash soap, and rinse the panels completely with clear water. • If insects, tar, or other similar deposits have accumulated on your vehicle, use MOPAR威 Super Kleen Bug and Tar Remover to remove. • Use MOPAR威 Cleaner Wax to remove road film, stains and to protect your paint finish. Take care never to scratch the paint.
400 MAINTAINING YOUR VEHICLE • If your vehicle is damaged due to an accident or similar cause which destroys the paint and protective coating, have your vehicle repaired as soon as possible. The cost of such repairs is considered the responsibility of the owner. • If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials are well packaged and sealed. • If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel.
MAINTAINING YOUR VEHICLE 401 Do not use abrasive cleaning components, solvents, steel wool or other aggressive material to clean the lenses. Interior Care Instrument Panel Cover The instrument panel cover has a low glare surface, which minimizes reflections in the windshield. Do not use protectants or other products, which may cause undesirable reflections. Use soap and warm water to restore the low glare surface.
402 MAINTAINING YOUR VEHICLE WARNING! Do not use volatile solvents for cleaning purposes. Many are potentially flammable, and if used in closed areas they may cause respiratory harm. YES Essentials威 Fabric Cleaning Procedure – If Equipped YES Essentials威 seats may be cleaned in the following manner: • Remove as much of the stain as possible by blotting with a clean, dry towel. • Blot any remaining stain with a clean, damp towel.
MAINTAINING YOUR VEHICLE 403 Cleaning Plastic Instrument Cluster Lenses The lenses in front of the instruments in this vehicle are molded in clear plastic. When cleaning the lenses, care must be taken to avoid scratching the plastic. 1. Clean with a wet, soft rag. A mild soap solution may be used, but do not use high alcohol content or abrasive cleaners. If soap is used, wipe clean with a clean damp rag. 2. Dry with a soft tissue.
404 MAINTAINING YOUR VEHICLE Installation Align the liner in the cupholder and press down firmly. FUSES Totally Integrated Power Module (TIPM) The TIPM is located in the engine compartment near the air cleaner assembly. This center contains cartridge fuses and mini fuses. A label that identifies each component may be printed on the inside of the cover. Refer to the graphic below for FUSES/TIPM location.
MAINTAINING YOUR VEHICLE 405 Cavity 1 2 3 Cartridge Fuse 40 Amp Green — — 4 — 5 — Mini Fuse Description — Power Top Module (If Equipped) 20 Amp Yellow AWD Module 10 Amp Red 10 Amp Red 20 Amp Yellow Battery Feed — Center High Mounted Stop Light (CHMSL)/ Brake Switch Battery Feed — Ignition Switch Trailer Tow — If Equipped Cavity Cartridge Fuse Mini Fuse 6 — 10 Amp Red 7 — 30 Amp Green 8 — 30 Amp Green 9 40 Amp Green Description Ignition Off Draw (IOD) — Power Mirror Switch/Clim
406 MAINTAINING YOUR VEHICLE Cavity Cartridge Fuse 10 — 11 — 12 — 13 — 14 — Mini Fuse Description Battery Feed — Cabin Compartment Node (CCN) 15 Amp Lt Selectable Power Blue Outlet 20 Amp — Yellow 20 Amp — Yellow Ignition Off Draw (IOD) — 10 Amp Cabin CompartRed ment Node (CCN)/ Interior Lighting 20 Amp Yellow Cavity Cartridge Fuse 15 40 Amp Green 16 — 17 — 18 40 Amp Green Mini Fuse Description Battery Feed — Radiator Fan Relay IGN Run/ACC 15 Amp Lt.
MAINTAINING YOUR VEHICLE 407 Cavity Cartridge Fuse 19 — 20 — 21 — 22 — 23 — Mini Fuse Description Ignition Off Draw (IOD) — Power Amp Feed 2 - if equipped Ignition Off 15 Amp Lt. Draw (IOD) — Blue Radio 10 Amp — Red Ignition Run — Climate 10 Amp Controls/Hot Red Cupholder - if equipped Auto Shutdown 15 Amp Lt.
408 MAINTAINING YOUR VEHICLE Cavity Cartridge Fuse Mini Fuse 28 — 10 Amp Red 29 — — 30 — 20 Amp Yellow 31 — 10 Amp Red 32 30 Amp Pink — Description Ignition Run — Occupant Classification Module (OCM)/Occupant Restraint Controller (ORC) Hot Car (No Fuse Required) Ignition Run — Heated Seats - If Equipped — Auto Shutdown (ASD) Relay Feed 1 Cavity Cartridge Fuse Mini Fuse 33 — 10 Amp Red 34 30 Amp Pink — Description Battery Feed — Switch Bank/ Diagnostic Link Connector/ Powertrain
MAINTAINING YOUR VEHICLE 409 Cavity Cartridge Fuse Mini Fuse 35 40 Amp Green — 36 30 Amp Pink — 37 — 25 Amp Clear Description Battery Feed — Anti-Lock Brakes (ABS) Module - If Equipped/ Electronic Stability Program (ESP) Module - If Equipped Battery Feed — Passenger Door Module (PDM)/ Driver Door Module (DDM) Power Top Module (If Equipped) CAUTION! • When installing the Totally Integrated Power Module cover, it is important to ensure the cover is properly positioned and fully latched.
410 MAINTAINING YOUR VEHICLE VEHICLE STORAGE If you will not be using your vehicle for more than 21 days, you may want to take steps to preserve your battery. • Disengage the mini-fuse in the Power Distribution Center labeled IOD (Ignition Off-Draw). • Disconnect the negative cable from the battery. REPLACEMENT BULBS All the inside bulbs are brass or glass wedge base. Aluminum base bulbs are not approved and should not be used for replacement. LIGHT BULBS — Interior Bulb No. Front Courtesy/Reading Light .
MAINTAINING YOUR VEHICLE 411 BULB REPLACEMENT Headlight 1. Raise and prop open the hood. Locate the connector behind the headlight. NOTE: It may be necessary to remove the air cleaner filter housing and position the totally integrated power module aside prior to replacing the low beam headlight on the driver’s side of the vehicle. 2. Reach into engine compartment and from behind the lamp assembly and grasp the connector.
412 MAINTAINING YOUR VEHICLE 3. Rotate bulb and connector one-quarter turn and pull outward from assembly. CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. 4. Pull the bulb out of the socket and replace the bulb. 5. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol. 6. Reinsert the bulb and socket assembly and rotate clockwise one-quarter turn to secure.
MAINTAINING YOUR VEHICLE 413 Front Turn Signal/Parking Light 1. Raise and prop open the hood. 2. Rotate the bulb’s electrical connector one-quarter turn counterclockwise and remove it from the headlight housing. 3. Remove the bulb from the connector socket and install the replacement bulb. 4. Install the bulb and connector assembly into the headlight housing and rotate the connector one-quarter turn clockwise to lock it in place.
414 MAINTAINING YOUR VEHICLE 1. Rotate the bulb’s electrical connector one-quarter turn counterclockwise and remove it from the fog light housing. 2. Remove the bulb from the connector socket and install the replacement bulb. CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with an oily surface, clean the bulb with rubbing alcohol. 3.
MAINTAINING YOUR VEHICLE 415 Tail/Stop, Rear Turn Signal and Backup Lights The taillights are a two piece design. The turn signal, brake and taillights are located in the rear corner body panel housing. The backup and taillights are located in the trunk lid housing. Changing the Tail/Stop Light or Rear Turn Signal Light 1.
416 MAINTAINING YOUR VEHICLE 2. Remove the two plastic wing nuts from the taillight housing. 3. Grasp the taillight housing and pull it firmly outward while pushing gently on the studs from inside to disengage the housing from the vehicle. 4. Rotate the applicable bulb’s electrical connector onequarter turn counterclockwise and remove it from the taillight housing. 1 — Tail/Stop Light 2 — Turn Signal Light 5. Remove the bulb from the connector socket and install the replacement bulb.
MAINTAINING YOUR VEHICLE 417 6. Install the bulb and connector assembly into the taillight housing and rotate the connector one-quarter turn clockwise to lock it in place. 7. Reinstall the taillight housing. Changing the Backup Light 1. Open the trunk. 2. Rotate the bulb’s electrical connector one-quarter turn counterclockwise and remove it from the housing. 1 — Rear Fog Light 2 — Backup Light 3. Remove the bulb from the connector socket and install the replacement bulb. 4.
418 MAINTAINING YOUR VEHICLE License Plate Light Center High-Mounted Stop Light (CHMSL) 1. Remove two retaining screws holding the light lens in place. 1. Open the trunk lid. 2. Gently pry the lens loose. 3. Pull bulb from socket, replace and reattach the light lens with the two retaining screws. 2. Rotate the bulb’s electrical connector one-quarter turn counterclockwise and remove it from the CHMSL housing.
MAINTAINING YOUR VEHICLE 419 3. Remove the bulb from the connector socket and install the replacement bulb. 4. Install the bulb and connector assembly into the CHMSL housing and rotate the connector one-quarter turn clockwise to lock it in place. FLUIDS AND CAPACITIES Fuel (Approximate) 2.4L and 2.7L Engines — (Except 2.4L PZEV) 2.4L PZEV (Partial Zero Emissions Vehicle) 3.5L Engine Engine Oil with Filter 2.4L Engine (SAE 5W-20, API Certified) 2.7L Engine (SAE 5W-20, API Certified) 3.
420 MAINTAINING YOUR VEHICLE Cooling System* 2.4L Engine (MOPAR威 Antifreeze/Coolant 5 Year/100,000 Mile Formula) or equivalent. 2.7L Engine (MOPAR威 Antifreeze/Coolant 5 Year/100,000 Mile Formula) or equivalent. 3.5L Engine (MOPAR威 Antifreeze/Coolant 5 Year/100,000 Mile Formula) or equivalent. * Includes heater and coolant recovery bottle filled to MAX level. U.S. Metric 7.7 Quarts 7.3 Liters 9.8 Quarts 9.3 Liters 11.
MAINTAINING YOUR VEHICLE 421 Component Engine Oil (3.5L Engine) Oil Filter (2.4L Engine ) Oil Filter (2.7L and 3.5L Engine) Spark Plugs (2.4L Engine except PZEV*) Spark Plugs (2.4L with PZEV) Spark Plugs (2.7L Engine) Spark Plugs (3.5L Engine) Fuel Selection (2.4L and 2.7L Engine) Fuel Selection (2.7L Engine - EXCEPT CALIFORNIA EMISSION STATES) Fuel Selection (3.5L Engine) * PZEV = Partial Zero Emission Vehicle Fluid, Lubricant, or Genuine Part Use API Certified engine oil. SAE 10W-30 is recommended.
422 MAINTAINING YOUR VEHICLE Chassis Component Automatic Transaxle Brake Master Cylinder Power Steering Reservoir Fluid, Lubricant, or Genuine Part MOPAR威 ATF+4 Automatic Transmission Fluid MOPAR威 DOT 3 and SAE J1703 should be used. If DOT 3 brake fluid is not available, then DOT 4 is acceptable. Use only recommended brake fluids.
MAINTENANCE SCHEDULES CONTENTS 䡵 Emissions Control System Maintenance . . . . . . 424 䡵 Maintenance Schedule . . . . . . . . . . . . . . . . . . 424 ▫ Required Maintenance Intervals . . . . . . . . . .
M A I N T E N A N C E 424 MAINTENANCE SCHEDULES EMISSIONS CONTROL SYSTEM MAINTENANCE The Scheduled Maintenance services listed in bold type must be done at the times or mileages specified to ensure the continued proper functioning of the emissions control system. These and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
MAINTENANCE SCHEDULES 425 M NOTE: • The oil change indicator message will not monitor the time since the last oil change. Change your vehicles oil if it has been 6 months since your last oil change even if the oil change indicator message is NOT illuminated. • Change your engine oil more often if you drive your vehicle off-road for an extended period of time. • Under no circumstances should oil change intervals exceed 6,000 miles (10 000 km) or six months, whichever comes first.
M A I N T E N A N C E S C H E D U L E S 8 426 MAINTENANCE SCHEDULES Once a Month At Each Oil Change • Check tire pressure and look for unusual wear or damage. • Change the engine oil filter. • Inspect the battery and clean and tighten the terminals as required. • Check the fluid levels of coolant reservoir, brake master cylinder, and transmission and add as needed. • Check all lights and other electrical items for correct operation. • Inspect the brake hoses and lines.
MAINTENANCE SCHEDULES 427 M 6,000 Miles (10,000 km) or 6 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. 12,000 Miles (20,000 km) or 12 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle in dusty or off-road conditions, inspect the engine air cleaner filter, and replace if necessary. ❏ Inspect the brake linings, and replace as necessary.
M 428 MAINTENANCE SCHEDULES A I N 18,000 Miles (30,000 km) or T 18 Months Maintenance E N Service Schedule A ❏ Change the engine oil and engine oil filter. N C ❏ Rotate tires. E 24,000 Miles (40,000 km) or 24 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle in dusty or off-road conditions, inspect the engine air cleaner filter, and replace if necessary. ❏ Inspect the brake linings, and replace as necessary.
MAINTENANCE SCHEDULES 429 M 30,000 Miles (50,000 km) or 30 Months Maintenance Service Schedule 36,000 Miles (60,000 km) or 36 Months Maintenance Service Schedule 42,000 Miles (70,000 km) or 42 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ Replace the engine air cleaner filter. ❏ Replace the spark plugs (2.4L Engine except PZEV*). ❏ Change the engine oil and engine oil filter. ❏ Rotate tires.
M 430 MAINTENANCE SCHEDULES A I N 48,000 Miles (80,000 km) or 48 Months Maintenance Service T Schedule E ❏ Change the engine oil and engine oil filter. N A ❏ Rotate tires. N ❏ If using your vehicle in dusty or off-road conditions, inspect the engine air cleaner filter, and replace if necessary. C E ❏ Inspect the brake linings, and replace as necessary. S C H E D U L E S ❏ ❏ ❏ ❏ 54,000 Miles (90,000 km) or 54 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires.
MAINTENANCE SCHEDULES 431 M 60,000 Miles (100,000 km) or 60 Months Maintenance Service Schedule ❏ ❏ ❏ ❏ ❏ ❏ ❏ Change the engine oil and engine oil filter. Rotate tires. Replace the engine air cleaner filter. Replace the spark plugs (2.4L Engine except PZEV*). Inspect the brake linings, and replace as necessary. Replace the air conditioning filter (if equipped). Change the automatic transaxle fluid & filter if using your vehicle for any of the following: police, taxi, fleet, or frequent trailer towing.
M 432 MAINTENANCE SCHEDULES A I N 72,000 Miles (120,000 km) or 72 Months Maintenance Service T Schedule E ❏ Change the engine oil and engine oil filter. N A ❏ Rotate tires. N ❏ If using your vehicle in dusty or off-road conditions, inspect the engine air cleaner filter, and replace if necessary. C E ❏ Inspect the brake linings, and replace as necessary. S C H E D U L E S ❏ ❏ ❏ ❏ 78,000 Miles (130,000 km) or 78 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter.
MAINTENANCE SCHEDULES 433 M 84,000 Miles (140,000 km) or 84 Months Maintenance Service Schedule 90,000 Miles (150,000 km) or 90 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle in dusty or off-road conditions, inspect the engine air cleaner filter, and replace if necessary. ❏ Inspect the brake linings, and replace as necessary. ❏ Replace the air conditioning filter (if equipped). ❏ Change the engine oil and engine oil filter.
M 434 MAINTENANCE SCHEDULES A I N 96,000 Miles (160,000 km) or 96 Months Maintenance Service T Schedule E ❏ Change the engine oil and engine oil filter. N A ❏ Rotate tires. N ❏ If using your vehicle in dusty or off-road conditions, inspect the engine air cleaner filter, and replace if necessary. C E ❏ Inspect the brake linings, and replace as necessary. S C H E D U L E S ❏ ❏ ❏ ❏ Replace the air conditioning filter (if equipped). Inspect the CV joints. Inspect the exhaust system.
MAINTENANCE SCHEDULES 435 M 108,000 Miles (180,000 km) or 108 Months Maintenance Service Schedule 114,000 Miles (190,000 km) or 114 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle in dusty or off-road conditions, inspect the engine air cleaner filter, and replace if necessary. ❏ Inspect the brake linings, and replace as necessary. ❏ Replace the air conditioning filter (if equipped). ❏ Change the engine oil and engine oil filter.
M 436 MAINTENANCE SCHEDULES A I N 120,000 Miles (200,000 km) or 120 Months Maintenance Service T Schedule E ❏ Change the engine oil and engine oil filter. N A ❏ Rotate tires. N ❏ Replace the engine air cleaner filter. C ❏ Replace the spark plugs (2.4L Engine except PZEV*). E ❏ Inspect the brake linings, and replace as necessary. S C H E D U L E S ❏ ❏ ❏ ❏ ❏ 126,000 Miles (210,000 km) or 126 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires.
MAINTENANCE SCHEDULES 437 M 132,000 Miles (220,000 km) or 132 Months Maintenance Service Schedule 138,000 Miles (230,000 km) or 138 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle in dusty or off-road conditions, inspect the engine air cleaner filter, and replace if necessary. ❏ Inspect the brake linings, and replace as necessary. ❏ Replace the air conditioning filter (if equipped). ❏ Change the engine oil and engine oil filter.
M 438 MAINTENANCE SCHEDULES A I N 144,000 Miles (240,000 km) or 144 Months Maintenance Service T Schedule E ❏ Change the engine oil and engine oil filter. N A ❏ Rotate tires. N ❏ If using your vehicle in dusty or off-road conditions, inspect the engine air cleaner filter, and replace if necessary. C E ❏ Inspect the brake linings, and replace as necessary. S C H E D U L E S ❏ ❏ ❏ ❏ Replace the air conditioning filter (if equipped). Inspect the CV joints. Inspect the exhaust system.
MAINTENANCE SCHEDULES 439 M † This maintenance is recommended by the manufacturer to the owner, but is not required to maintain emissions warranty. WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS 䡵 Suggestions For Obtaining Service For Your Vehicle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 443 ▫ Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) . . . . . . . . . . . . 445 ▫ Prepare For The Appointment . . . . . . . . . . . . 443 ▫ Service Contract . . . . . . . . . . . . . . . . . . . . . 445 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . . 443 䡵 Warranty Information (U.S. Vehicles Only) . . . .
442 IF YOU NEED CONSUMER ASSISTANCE 䡵 Publication Order Forms . . . . . . . . . . . . . . . . . 447 ▫ Traction Grades . . . . . . . . . . . . . . . . . . . . . . 449 䡵 Department Of Transportation Uniform Tire Quality Grades . . . . . . . . . . . . . . . . . . . . . . . . 448 ▫ Temperature Grades . . . . . . . . . . . . . . . . . . . 450 ▫ Treadwear . . . . . . . . . . . . . . . . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE 443 SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager. Keep a maintenance log of your vehicle’s service history. This can often provide a clue to the current problem.
444 IF YOU NEED CONSUMER ASSISTANCE This is why you should always talk to an authorized dealer’s service manager first. Most matters can be resolved with this process. • If for some reason you are still not satisfied, talk to the general manager or owner of the authorized dealership. They want to know if you need assistance. • If an authorized dealership is unable to resolve the concern, you may contact the manufacturer’s customer center.
IF YOU NEED CONSUMER ASSISTANCE 445 Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommunication Devices for the Deaf) equipment at its customer center. Any hearing or speech impaired customer, who has access to a TDD or a conventional teletypewriter (TTY) in the United States, can communicate with the manufacturer by dialing 1–800–380–CHRY.
446 IF YOU NEED CONSUMER ASSISTANCE WARNING! Engine exhaust, some of its constituents, and certain vehicle components contain, or emit, chemicals known to the State of California to cause cancer and birth defects, or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain, or emit, chemicals known to the State of California to cause cancer and birth defects, or other reproductive harm. WARRANTY INFORMATION (U.S.
IF YOU NEED CONSUMER ASSISTANCE 447 To contact NHTSA, you may either call the Auto Safety Hotline toll free at 1–888–327–4236 (TTY: 1–800–424– 9153), or go to http://www.safercar.gov; or write to: Administrator, NHTSA, 400 Seventh Street, SW., Washington, D.C. 20590. You can also obtain other information about motor vehicle safety from http://www.safercar.gov. PUBLICATION ORDER FORMS To order the following manuals, you may use either the website or the phone numbers listed below.
448 IF YOU NEED CONSUMER ASSISTANCE • Diagnostic Procedure Manuals Diagnostic Procedure Manuals are filled with diagrams, charts and detailed illustrations. These practical manuals make it easy for students and technicians to find and fix problems on computer-controlled vehicle systems and features. They show exactly how to find and correct problems the first time, using step-bystep troubleshooting and drivability procedures, proven diagnostic tests and a complete list of all tools and equipment.
IF YOU NEED CONSUMER ASSISTANCE 449 Treadwear The Treadwear grade is a comparative rating, based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half times as well on the government course as a tire graded 100.
450 IF YOU NEED CONSUMER ASSISTANCE Temperature Grades The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
INDEX 10
452 INDEX About Your Brakes . . . . . . . . . . . . . . . . . . . . 282,285 ABS (Anti-Lock Brake System) . . . . . . . . . . . . 286,288 Adding Engine Coolant (Antifreeze) . . . . . . . . . . 390 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 333 Adding Washer Fluid . . . . . . . . . . . . . . . . . . . . . 385 Additives, Fuel . . . . . . . . . . . . . . . . . . . . . . . . . 328 Air Cleaner, Engine (Engine Air Cleaner Filter) . . . 379 Air Conditioner Maintenance . . . . . . . . . . . .
INDEX 453 Automatic Temperature Control (ATC) . . . . . . . . . 253 Automatic Transaxle . . . . . . . . . . . . . . . . . 13,270,395 Adding Fluid . . . . . . . . . . . . . . . . . . . 396,397,422 Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 397 Fluid and Filter Changes . . . . . . . . . . . . . . . . . 397 Fluid Level Check . . . . . . . . . . . . . . . . . . . 396,397 Interlock System . . . . . . . . . . . . . . . . . . . . 271,272 Reset Mode . . . . . . . . . . . . . . . . . . . .
454 INDEX Caps, Filler Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 333 Oil (Engine) . . . . . . . . . . . . . . . 369,370,371,377,378 Power Steering . . . . . . . . . . . . . . . . . . . . . . . . 282 Radiator (Coolant Pressure) . . . . . . . . . . . . . . . 391 Car Washes . . . . . . . . . . . . . . . . . . . . . . . . . . . . 399 Carbon Monoxide Warning . . . . . . . . . . . . . . . . . 329 Cargo Area Features . . . . . . . . . . . . . . . . . . . . . . 164 Cargo Compartment . . .
INDEX 455 Contract, Service . . . . . . . . . . . . . . . . . . . . . . . . 445 Coolant Pressure Cap (Radiator Cap) . . . . . . . . . . 391 Cooling System . . . . . . . . . . . . . . . . . . . . . . . . . 388 Adding Coolant (Antifreeze) . . . . . . . . . . . . . . 390 Coolant Capacity . . . . . . . . . . . . . . . . . . . . . . 419 Coolant Level . . . . . . . . . . . . . . . . . . . . . . 388,392 Disposal of Used Coolant . . . . . . . . . . . . . . . . 392 Drain, Flush, and Refill . . . . . . . . . . . . .
456 INDEX Door Opener, Garage . . . . . . . . . . . . . . . . . Driving On Slippery Surfaces . . . . . . . . . . . . . . . Through Flowing, Rising, or Shallow Standing Water . . . . . . . . . . . . . . . . . . . . DVD Player (Video Entertainment System™) . . . . 148 . . . . 278 . . . . 279 . . . . 244 E-85 Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 330 Electric Rear Window Defrost . . . . . . . . . . . . . . . 169 Electric Remote Mirrors . . . . . . . . . . . . . . . . . . . .
INDEX 457 Temperature Gauge . . . . . . . . . . . . . . . . . . . . 177 Engine Oil Viscosity . . . . . . . . . . . . . . . . . . . 377,378 Enhanced Accident Response Feature . . . . . . . . . . 63 Entry System, Illuminated . . . . . . . . . . . . . . . . . . 21 Ethanol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 326 Event Data Recorder . . . . . . . . . . . . . . . . . . . . . . 67 Exhaust Gas Caution . . . . . . . . . . . . . . . . 81,329,386 Exhaust System . . . . . . . . . . . . . . .
458 INDEX Power Steering . . . . . . . . . . . . . . . . . . . . . 282,422 Fluids . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 420 Fluids, Lubricants and Genuine Parts . . . . . . . . . . 420 Fog Light Service . . . . . . . . . . . . . . . . . . . . . . . . 413 Fog Lights . . . . . . . . . . . . . . . . . . . . . . . 138,185,413 Folding Rear Seat . . . . . . . . . . . . . . . . . . . . . 132,133 Freeing A Stuck Vehicle . . . . . . . . . . . . . . . . . . . 363 Fuel . . . . . . . . . . .
INDEX 459 Gearshift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 273 General Information . . . . . . . . . . . . . . . . . 18,119,324 General Maintenance . . . . . . . . . . . . . . . . . . . . . 375 Glass Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . 402 Gross Axle Weight Rating . . . . . . . . . . . . . . . 337,339 Gross Vehicle Weight Rating . . . . . . . . . . . . . 337,339 GVWR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
460 INDEX Infant Restraint . . . . . . . . . . . . . . . . . . . . . . . . 69,70 Information Center, Vehicle . . . . . . . . . . . . . . . . . 189 Inside Rearview Mirror . . . . . . . . . . . . . . . . . . . . 87 Instrument Cluster . . . . . . . . . . . . . . . . . 175,176,177 Instrument Panel and Controls . . . . . . . . . . . . . . 174 Instrument Panel Cover . . . . . . . . . . . . . . . . . . . 401 Instrument Panel Lens Cleaning . . . . . . . . . . . . . 403 Integrated Power Module (Fuses) . . . . . . .
INDEX 461 Anti-Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . 287 Back-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . 415 Brake Warning . . . . . . . . . . . . . . . . . . . . . . . . 183 Bulb Replacement . . . . . . . . . . . . . . . . . . . . . . 411 Center Mounted Stop . . . . . . . . . . . . . . . . . . . 418 Daytime Running . . . . . . . . . . . . . . . . . . . . . . 138 Electronic Stability Program (ESP) Indicator . . . 293 Engine Temperature Warning . . . . . . . . . . . . .
462 INDEX Power Door . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Low Tire Pressure System . . . . . . . . . . . . . . . . . . 316 Lower Anchors and Tether for CHildren (LATCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 Lubrication, Body . . . . . . . . . . . . . . . . . . . . . . . 384 Lumbar Support . . . . . . . . . . . . . . . . . . . . . . . . 128 Maintenance Free Battery . . . . . . . . . . . . . . . . . . 380 Maintenance, General . . . . . . . . . . . . . . . . . . .
INDEX 463 Oil Change Indicator, Reset . . . . . . . . . . . . . . 181,191 Oil, Engine . . . . . . . . . . . . . . . . . . . . . . . . . 375,420 Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . 419 Change Interval . . . . . . . . . . . . . . . 181,191,376,424 Checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . 375 Dipstick . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 375 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . 378 Filter . . . . . . . . . .
464 INDEX Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 Outlet (Auxiliary Electrical Outlet) . . . . . . . . . . 158 Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 Steering . . . . . . . . . . . . . . . . . . . . . . . . . . 281,282 Sunroof . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155 Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Pregnant Women and Seat Belts . . . . . . . . . . . . . . 52 Preparation for Jacking . .
INDEX 465 Replacement Keys . . . . . . . . . . . . . . . . . . . . . . . . 17 Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . 374 Replacement Tires . . . . . . . . . . . . . . . . . . . . . . . 312 Reporting Safety Defects . . . . . . . . . . . . . . . . . . . 446 Resetting Oil Change Indicator . . . . . . . . . . . 181,191 Restraint, Head . . . . . . . . . . . . . . . . . . . . . . . . . 129 Restraints, Child . . . . . . . . . . . . . . . . . . . . . . . . . 69 Restraints, Infant . . . . .
466 INDEX Heated . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130 Lumbar Support . . . . . . . . . . . . . . . . . . . . . . . 128 Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 Rear Folding . . . . . . . . . . . . . . . . . . . . . . . 132,133 Rear Folding (Sedan) . . . . . . . . . . . . . . . . . . . 164 Reclining . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127 Security Alarm (Theft Alarm) . . . . . . . . . . . . . . . .
INDEX 467 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163,410 Storage, Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . 259 Stuck, Freeing . . . . . . . . . . . . . . . . . . . . . . . . . . 363 Sun Roof . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155 Supplemental Restraint System - Airbag . . . . . . . . 53 Synthetic Engine Oil . . . . . . . . . . . . . . . . . . . . . . 378 Tachometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179 Taillights . . .
468 INDEX Radial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 308 Replacement . . . . . . . . . . . . . . . . . . . . . . . . . 312 Rotation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 315 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . 296,305 Sizes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 298 Snow Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . 314 Spare Tire . . . . . . . . . . . . . . . . . . . . . . . . . . . 353 Spinning . . . .
INDEX 469 Transmitter Programming (Remote Keyless Entry) . . . . . . . . . . . . . . . . . . . . 26 Transporting Pets . . . . . . . . . . . . . . . . . . . . . . . . 80 Tread Wear Indicators . . . . . . . . . . . . . . . . . . . . . 311 Trip Odometer . . . . . . . . . . . . . . . . . . . . . . . . . . 180 Trip Odometer Reset Button . . . . . . . . . . . . . . . . 182 Trunk Lid (Deck Lid) . . . . . . . . . . . . . . . . . . . . . . 39 Trunk Release, Emergency . . . . . . . . . . . . . . . .
470 INDEX Washing Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . 399 Water Driving Through . . . . . . . . . . . . . . . . . . . . . . 279 Wheel and Wheel Trim . . . . . . . . . . . . . . . . . . . . 400 Wheel and Wheel Trim Care . . . . . . . . . . . . . . . . 400 Wind Buffeting . . . . . . . . . . . . . . . . . . . . . . . 39,157 Window Fogging . . . . . . . . . . . . . . . . . . . . . . . . 260 Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Power . . . . . . . . . . .
INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained personnel. The following must be observed during installation. The positive power connection should be made directly to the battery and fused as close to the battery as possible.
Chrysler LLC 81-026-0904 First Edition Printed in U.S.A.
