2008 Sebring 2008 OWNER’ S MANUAL 81-026-0804 First Edition Printed in U.S.A.
VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name Chrysler LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefor. DRIVING AND ALCOHOL Drunken driving is one of the most frequent causes of accidents. Your driving ability can be seriously impaired with blood alcohol levels far below the legal minimum. If you are drinking, don’t drive. Ride with a designated non-drinking driver, call a cab, a friend, or use public transportation.
SECTION TABLE OF CONTENTS PAGE 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81 3 4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION CONTENTS 䡵 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 Vehicle Identification Number . . . . . . . . . . . . . . . 6 䡵 How To Use This Manual . . . . . . . . . . . . . . . . . . 4 䡵 Vehicle Modifications/Alterations . . . . . . . . . . . . 7 䡵 Warnings And Cautions . . . . . . . . . . . . . . . . . . .
4 INTRODUCTION INTRODUCTION This Owner’s Manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your vehicle. It is supplemented by a Warranty Information Booklet and various customer-oriented documents. You are urged to read these publications carefully. Following the instructions and recommendations in this manual will help assure safe and enjoyable operation of your vehicle.
INTRODUCTION 5 1
6 INTRODUCTION WARNINGS AND CAUTIONS This manual contains WARNINGS against operating procedures that could result in an accident or bodily injury. It also contains CAUTIONS against procedures that could result in damage to your vehicle. If you do not read this entire manual you may miss important information. Observe all Warnings and Cautions. VEHICLE IDENTIFICATION NUMBER The Vehicle Identification Number (VIN) is found on the left front corner of the instrument panel, visible through the windshield.
INTRODUCTION 7 VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS 䡵 A Word About Your Keys . . . . . . . . . . . . . . . . . .12 ▫ Rearming Of The System . . . . . . . . . . . . . . . . .18 ▫ Ignition Key Removal . . . . . . . . . . . . . . . . . . .13 ▫ To Arm The System . . . . . . . . . . . . . . . . . . . . .19 ▫ Key-In-Ignition Reminder . . . . . . . . . . . . . . . .14 ▫ To Disarm The System . . . . . . . . . . . . . . . . . . .19 ▫ Locking Doors With The Key . . . . . . . . . . . . . .
10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Using The Express Down Windows Feature — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . .25 ▫ Using The Panic Alarm . . . . . . . . . . . . . . . . . .25 ▫ Programming Additional Transmitters . . . . . . . .25 ▫ Battery Replacement . . . . . . . . . . . . . . . . . . . .25 ▫ General Information . . . . . . . . . . . . . . . . . . . .26 䡵 Remote Start System — If Equipped . . . . . . . . . .27 ▫ How To Use Remote Start . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 ▫ Rear Seat Belts . . . . . . . . . . . . . . . . . . . . . . . .48 ▫ Airbag Deployment Sensors And Controls . . . . .59 ▫ Seat Belt Pretensioners . . . . . . . . . . . . . . . . . . .48 ▫ Event Data Recorder (EDR) . . . . . . . . . . . . . . .65 ▫ Enhanced Seat Belt Reminder System (BeltAlert威) . . . . . . . . . . . . . . . . . . . . . . . . . .49 ▫ Child Restraint . . . . . . . . . . . . . . . . . . . . . . . .67 ▫ BeltAlert威 Programming . . . . . . .
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS You can insert the double-sided keys into the locks with either side up. Vehicle Key The authorized dealer that sold you your vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys from your authorized dealer. Ask your authorized dealer for these numbers and keep them in a safe place.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Ignition Key Removal Automatic Transaxle Place the gear selector lever in PARK. Turn the ignition switch to the ACC position, push the key and cylinder inward, rotate the key to the LOCK position. Then remove the key. 13 NOTE: • If you try to remove the key before you place the selector lever in PARK, the key may become trapped temporarily in the ignition switch lock cylinder.
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • For vehicles equipped with EVIC, the power window switches, radio, hands–free system (if equipped), and power outlets will remain active for up to 10 minutes after the ignition switch is turned to the LOCK position. Opening either door will cancel this feature. The time for this feature is programmable.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Locking Doors With The Key There is only one external door lock cylinder which is located in the driver’s door only. You can insert the key with either side up. To lock the door, turn the key rearward. To unlock the door, turn the key forward. See ”Maintenance Procedures” in Section 7 “Maintaining Your Vehicle” of this manual for door lock lubrication. SENTRY KEY姞 The Sentry Key威 Immobilizer System prevents unauthorized vehicle operation by disabling the engine.
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CAUTION! Always remove Sentry Keys威 from the vehicle and lock all doors when leaving the vehicle unattended. NOTE: • The Sentry Key威 Immobilizer System is not compatible with some aftermarket remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 NOTE: When having the Sentry Key威 Immobilizer System serviced, bring all vehicle keys with you to the authorized dealer. addition, the Vehicle Security Alarm Indicator Light will begin to flash. Turn the ignition switch to the LOCK position and remove the second key. Sentry Key姞 Programming You can program new keys to the system if you have two valid Sentry Keys威 by performing the following procedure: 4. Insert a blank Sentry Key威 into the ignition switch.
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: If a programmed key is lost, see your authorized dealer to have all remaining keys erased from the systems memory. This will prevent the lost key from starting your vehicle. The remaining keys must then be reprogrammed. All vehicle keys must be taken to your authorized dealer at the time of service to be reprogrammed. General Information The Sentry Key威 system complies with FCC rules part 15 and with RSS-210 of Industry Canada.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Arm The System: 1. Remove the keys from the ignition switch and get out of the vehicle. 2. Lock the doors by pressing the power door lock switch or the LOCK button on the Remote Keyless Entry (RKE) transmitter. NOTE: The system will not arm if you lock the doors with the manual door lock plungers. 3. The indicator light in the instrument cluster will flash rapidly for 16 seconds. This shows that the system is arming.
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The system remains armed during trunk entry. Pressing the trunk button will not disarm the system. If someone enters the vehicle through the trunk and opens any door, the alarm will sound. • When the system is armed, the interior power door lock switches will not unlock the doors. The VSA system is designed to protect your vehicle; however, you can create conditions where the system will give you a false alarm.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 NOTE: • The front courtesy overhead console and door courtesy lights do not turn on if the dimmer control is in the interior lights ON position (extreme top position). 2 • The illuminated entry system will not operate if the dimmer control is in the “defeat” position (extreme downward position).
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE TO UNLOCK THE DOORS Press and release the UNLOCK button on the transmitter once to unlock the driver’s door, or twice to unlock all doors. The turn signal lights will flash to acknowledge the unlock signal. The illuminated entry system (if equipped) will also turn on.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Flash Lights With Lock The feature will cause the turn signal lights to flash when the doors are locked or unlocked with the transmitter. This feature can be turned on or turned off.
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Approach,” under “Personal Settings (Customer Programmable Features), under “Electronic Vehicle Information Center (EVIC)” in Section 4 of this manual. TO LOCK THE DOORS Press and release the LOCK button on the transmitter to lock all doors. The turn signal lights will flash and the horn will chirp once to acknowledge the lock signal. Sound Horn with Lock This feature will cause the horn to chirp when the doors are locked with the transmitter.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 TO UNLATCH THE TRUNK Press the TRUNK button on the transmitter two times to unlatch the trunk. The PANIC alarm will stay on for three minutes unless you turn it off by pressing the PANIC button a second time or if the vehicle speed is 5 mph (8 km/h) or greater. USING THE EXPRESS DOWN WINDOWS FEATURE — IF EQUIPPED This feature allows you to remotely lower both front door windows at the same time.
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 1. With the transmitter buttons facing down, use a flat blade to pry the two halves of the transmitter apart. Make sure not to damage the seal during removal. 2. Remove and replace the batteries. Avoid touching the new batteries with your fingers. Skin oils may cause battery deterioration. If you touch a battery, clean it with rubbing alcohol. 3. To assemble the transmitter case, snap the two halves together.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 If your Remote Lock Control fails to operate from a normal distance, check for these two conditions. 1. Weak batteries in the transmitter. The expected life of batteries is five years. 2 2. Closeness to a radio transmitter such as a radio station tower, airport transmitter, military base, and some mobile or CB radios.
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE HOW TO USE REMOTE START All of the following conditions must be met before the engine will remote start: • Shift the gear selector lever into PARK. • Doors closed. • Hood closed. • Trunk closed. • Hazard switch off. • Brake switch inactive (brake pedal not pressed). • Ignition key removed from ignition switch. • Battery at an acceptable charge level. • RKE PANIC button not pressed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Exit Remote Start Mode And Drive The Vehicle Before the end of the 15-minute cycle, press and release the UNLOCK button on the RKE transmitter to unlock the doors and disarm the Vehicle Security Alarm (if equipped). Then, within 15 minutes, insert the key into the ignition switch and turn the switch to the ON position. 29 DOOR LOCKS MANUAL DOOR LOCKS To lock each door, push the door lock plunger on each door trim panel downward.
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If the door lock plunger is down when you shut the door, the door will lock. Therefore, make sure the keys are not inside the vehicle before closing the door. WARNING! • For personal security and safety in the event of an accident, lock the vehicle doors as you drive as well as when you park and leave the vehicle. • When leaving the vehicle always remove the key from the ignition lock, and lock your vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 CAUTION! An unlocked vehicle is an invitation to thieves. Always remove the key from the ignition and lock all of the doors when leaving the vehicle unattended. 2 POWER DOOR LOCKS A door lock switch is located on the driver and passenger door panel. Press this switch to lock or unlock the doors. Power Door Lock Switch Automatic Door Locks — If Equipped The auto door lock feature can be enabled or disabled by your authorized dealer.
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Automatic Unlock Doors On Exit The doors will unlock automatically on vehicles with power door locks if: 1. The Auto Unlock feature is enabled. 2. The transmission was in gear and the vehicle speed returned to 0 mph (0 km/h). 3. The transmission is in NEUTRAL or PARK. 4. The driver door is opened. 5. The doors were not previously unlocked. 6. The vehicle speed is 0 mph (0 km/h).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 NOTE: Use the Auto Unlock On Exit feature in accordance with local laws. CHILD-PROTECTION DOOR LOCK SYSTEM (REAR DOORS) The Rear Door Child-Protection Locks are located inside the rear edge of the door. Insert the tip of the ignition key or similar flat-bladed object into the lock and rotate approximately one-quarter turn to the lock or unlock position (as indicated by the stamped icons).
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged. POWER WINDOWS POWER WINDOW SWITCHES The control on the driver’s door has up-down switches that give you fingertip control of all four power windows.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE There is a single window control on the passenger’s door trim panel, which operates the passenger door window. The window controls will operate when the ignition switch is turned to the ON or ACC position, and when the accessory delay feature is active. WARNING! Never leave children in a vehicle, with the keys in the ignition switch. Occupants, particularly unattended children, can become entrapped by the windows while operating the power window switches.
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE For vehicles equipped with EVIC, the power window switches will remain active for up to 10 minutes after the ignition switch is turned off. Opening either door will cancel this feature. The time for this feature is programmable. For details, refer to “Key-Off Power Delay,” under “Personal Settings (Customer Programmable Features)” under “Electronic Vehicle Information Center (EVIC)” in Section 4 of this manual.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! When the window is almost closed, there is no anti-pinch protection. To avoid personal injury, be sure to clear your arms, hands, fingers and all objects from the window path before closing. 37 WINDOW LOCKOUT SWITCH The window lockout switch on the driver’s door allows you to disable the window control on the other doors. To disable the window controls on the other doors, press the window lock button.
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WIND BUFFETING Wind buffeting can be described as the perception of pressure on the ears or a helicopter type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occurrence and can be minimized. If the buffeting occurs with the rear windows open, then open the front and rear windows together to minimize the buffeting.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE With the ignition ON, the word “deck” will display in place of the odometer display indicating that the trunk is open. The odometer display will reappear once the trunk is closed or if the trip button is depressed. With the key in the lock position or with the key out, the word “deck” will display until the trunk is closed. On EVIC-equipped vehicles, the words “Trunk Ajar” will display.
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE TRUNK INTERNAL EMERGENCY RELEASE inside the trunk, the trunk can be simply opened by pulling on the glow-in-the-dark handle attached to the trunk latching mechanism. OCCUPANT RESTRAINTS Some of the most important safety features in your vehicle are the restraint systems.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • An energy absorbing steering column and steering wheel • Supplemental Side Airbag Inflatable Curtains (SABIC) that span the front and second rows for sedans — if equipped • Supplemental seat side (Thorax) airbags — if equipped • Front seat belt retractors incorporate pretensioners to enhance occupant protection by managing occupant energy during an impact event.
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! In a collision, you and your passengers can suffer much greater injuries if you are not properly buckled up. You can strike the interior of your vehicle or other passengers, or you can be thrown out of the vehicle. Always be sure you and others in your vehicle are buckled up properly. Buckle up even though you are an excellent driver, even on short trips. Someone on the road may be a poor driver and cause a collision that includes you.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 WARNING! WARNING! • Be sure everyone in your vehicle is in a seat and using a seat belt properly. • Wearing your belt in the wrong place could make your injuries in a collision much worse. You might suffer internal injuries, or you could even slide out of part of the belt. Follow these instructions to wear your seat belt safely and to keep your passengers safe, too. • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle.
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. The seat belt latch plate is above the back of the front seat, next to your arm. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to allow the belt to go around your lap. 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” WARNING! • A belt that is buckled into the wrong buckle will not protect you properly.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 WARNING! • A belt that is worn under your arm is very dangerous. Your body could strike the inside surfaces of the vehicle in a collision, increasing head and neck injury. A belt worn under the arm can cause internal injuries. Ribs aren’t as strong as shoulder bones. Wear the belt over your shoulder so that your strongest bones will take the force in a collision.
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision. WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 6. To release the belt, push the red button on the buckle. The belt will automatically retract to its stowed position. If necessary, slide the latch plate down the webbing to allow the belt to retract fully. WARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately.
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Adjustable Upper Shoulder Belt Anchorage In the front seat, the shoulder belt can be adjusted upward or downward to position the belt away from your neck. Push anchorage button to release the anchorage, and move it up or down to the position that serves you best. Adjustable Anchorage As a guide, if you are shorter than average, you will prefer a lower position, and if you are taller than average, you’ll prefer a higher position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE In addition, the front passenger seat belt includes a two-stage load-limiting feature to enhance occupant protection for the same reason. NOTE: These devices are not a substitute for proper seat belt placement by the occupant. The seat belt still must be worn snugly and positioned properly. The pretensioners are triggered by the Occupant Restraint Controller (ORC). Like the front airbags, the pretensioners are single use items.
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Within 60 seconds of turning the ignition switch to the ON position, unbuckle and then re-buckle the driver’s seat belt at least three times within 10 seconds, ending with the seat belt buckled. NOTE: Watch for the Seat Belt Warning Light to turn on while unbuckling and off while re-buckling the seat belt. It may be necessary to retract the seat belt partially each time when unbuckling. 4. Turn the ignition switch to the LOCK position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE How to Disengage the Automatic Locking Mode Unbuckle the combination lap/shoulder belt and allow it to retract completely to disengage the Automatic Locking Mode and activate the vehicle sensitive (emergency) locking mode. Seat Belts And Pregnant Women We recommend that pregnant women use the seat belts throughout their pregnancy. Keeping the mother safe is the best way to keep the baby safe.
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Supplemental Restraint System (SRS) - Airbag This vehicle has airbags for both the driver and front passenger as a supplement to the seat belt restraint systems. The driver’s front airbag is mounted in the center of the steering wheel. The passenger’s front airbag is mounted in the instrument panel, above the glove compartment. The words SRS AIRBAG are embossed on the airbag covers.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 This vehicle may also be equipped with window bags to protect the driver, front, and rear passengers sitting next to a window. If the vehicle is equipped with window bags, they are located above the side windows. Their covers are also labeled SRS AIRBAG. • Front Seat— side mounted (Thorax) Airbags — If Equipped NOTE: Airbag covers may not be obvious in the interior trim; but they will open to allow airbag deployment.
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The first stage inflator is triggered immediately during an impact that requires airbag deployment. The timing of the second stage determines whether the output force is low, medium, or high. If a low output is sufficient to meet the need, the second stage is expended later in the crash event. Driver Airbag Special Features Driver airbag deployment and force level is controlled by the driver’s seat position as well as impact severity.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 Supplemental Side Airbag Inflatable Curtain (SABIC) — If Equipped Supplemental Side Airbag Inflatable Curtain (SABIC) Airbags offer side-impact protection to front and rear seat outboard occupants in addition to that provided by the body structure. Each airbag features inflated chambers place adjacent to the head of each outboard occupant that reduce the potential for side-impact head injuries.
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Do not put anything on or around the airbag covers or attempt to open them manually. You may damage the airbags and you could be injured because the airbags are not there to protect you. These protective covers for the airbag cushions are designed to open only when the airbags are inflating. Side Airbag Inflatable Curtains (SABIC) Location NOTE: Airbag covers may not be obvious in the interior trim; but they will open to allow airbag deployment.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • If your vehicle is equipped with left and right window bags, do not stack luggage or other cargo up high enough to block the location of the Side Airbag Inflatable Curtains (SABIC). The area where the side curtain airbag is located should remain free from any obstructions. • Do not attach cup holders or any other objects on or around the door. The inflating side airbag could drive the object into occupants, causing serious injury.
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Children that are not big enough to wear the vehicle seat belt properly (see Section on Child Restraints) should be secured in the rear seat in child restraints or beltpositioning booster seats. Older children who do not use child restraints or belt-positioning booster seats should ride properly buckled up in the rear seat. Never allow children to slide the shoulder belt behind them or under their arm.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly. In some collisions, the airbags won’t deploy at all. Always wear your seat belts even though you have airbags. • Being too close to the steering wheel or instrument panel during front airbag deployment could cause serious injury. Airbags need room to inflate.
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE OFF position, in the ACC position, or not in the ignition, the airbags are not on and will not inflate. The ORC contains a backup power supply system that will deploy the airbags even if the battery loses power or it becomes disconnected prior to deployment. Also, the ORC turns on the Airbag Warning Light in the instrument panel for six to eight seconds for a self-check when the ignition is first turned on.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Side Inflatable Curtain and Front seat-mounted Airbags — If equipped The Occupant Restraint Controller System (ORC) deploys the side inflatable curtain and seat-mounted thorax side airbags during collision with other vehicles and during collisions where the impact is confined to a particular area of the vehicle — such as collisions with poles, trees or similar objects.
62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Unapproved modifications or service procedures to the front passenger seat assembly, its related components, or seat cover may inadvertently change the airbag deployment in case of a frontal crash. This could result in death or serious injury to the front seat passenger if the vehicle is involved in an accident. A modified vehicle may not comply with required Federal Motor Vehicle Safety Standards (FMVSS).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If you do have a collision, which deploys the airbags, any or all of the following may occur: • The nylon airbag material may sometimes cause abrasions and/or skin reddening to the driver and front passenger as the airbags deploy and unfold. The abrasions are similar to friction rope burns or those you might get sliding along a carpet or gymnasium floor. They are not caused by contact with chemicals. They are not permanent and normally heal quickly.
64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Maintaining Your Airbag System NOTE: Perchlorate Material — special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate WARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. You could be injured if the airbag system is not there to protect you.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag Light You will want to have the airbags ready to inflate for your protection in a collision. While the airbag system is designed to be maintenance free, if any of the following occurs, have an authorized dealer service the system immediately. • The AIRBAG light does not come on during the six to eight seconds when the ignition switch is first turned on. • The light remains on after the six to eight second interval.
66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Under certain circumstances, EDR data may not be recorded (e.g., loss of battery power). In conjunction with other data gathered during a complete accident investigation, the electronic data may be used by Chrysler Corporation and others to learn more about the possible causes of crashes and associated injuries in order to assess and improve vehicle performance.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 3. Requested by police under a legal warrant. • Engine control status (including engine speed) 4. Otherwise required by law.
68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! In a collision, an unrestrained child, even a tiny baby, can become a missile inside the vehicle. The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are. The child and others could be badly injured. Any child riding in your vehicle should be in a proper restraint for the child’s size.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Rearward-facing child seats must NEVER be used in the front seat of a vehicle with a front passenger airbag. An airbag deployment could cause severe injury or death to infants in this position. Older Children and Child Restraints Children who weigh more than 20 lbs (9 kg) and who are older than one year can ride forward-facing in the vehicle.
70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Here are some tips on getting the most out of your child restraints: • Children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the seatback, should use the lap/shoulder belt in a rear seat. • Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE around, and insert the latch plate into the buckle again. If you still can’t make the child restraint secure, try a different seating position. • Buckle the child into the seat according to the child restraint manufacturer’s directions. • When your child restraint is not in use, secure it in the vehicle with the seat belt or remove it from the vehicle. Don’t leave it loose in the vehicle.
72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Rear Seat LATCH Anchors Child restraints systems having attachments designed to connect to the lower anchorages are now available. Child restraints having tether straps and hooks for connection to the top tether anchorage have been available for some time. In fact, many child restraint manufacturers will provide add-on tether strap kits for some of their older products. Tether anchorage kits are also available for most older vehicles.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE have tether straps, and you are urged to take advantage of all of the available attachments provided with your child restraint in any vehicle. NOTE: When using the LATCH attaching system to install a child restraint, please ensure that all seat belts not being used for occupant restraints are stowed and out of reach of children.
74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE window. These tether strap anchorages are under a plastic cover with this symbol on it. Many, but not all restraint systems will be equipped with separate straps on each side, with each having a hook or connector for attachment to the lower anchorage and a means of adjusting the tension in the strap.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 the child restraint belt path and then buckle it. This should stow the seat belt out of the reach of an inquisitive child. Remind all children in the vehicle that the seat belts are not toys and should not be played with, and never leave your child unattended in the vehicle. 2 WARNING! Improper installation of a child restraint to the LATCH anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed.
76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE between the two posts. If not possible, lower the head restraint and pass the tether strap around the outboard side of the head restraint. 3. Attach the tether strap hook (A) of the child restraint to the anchor (B) and remove slack in the tether strap according to the child restraint manufacturer’s instructions. WARNING! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE In the rear seat, you may have trouble tightening the lap/shoulder belt on the child restraint because the buckle or latch plate is too close to the belt path opening on the restraint. Disconnect the latch plate from the buckle and twist the short buckle-end belt several times to shorten it. Insert the latch plate into the buckle with the release button facing out.
78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Pets should be restrained in the rear seat in pet harnesses or pet carriers that are secured by seat belts. ENGINE BREAK-IN RECOMMENDATIONS A long break-in period is not required for the engine in your vehicle. Drive moderately during the first 300 mi (500 km). After the initial 60 mi (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Do not run the engine in a closed garage or in confined areas any longer than needed to move your vehicle in or out of the area. If it is necessary to sit in a parked vehicle with the engine running, adjust your heating or cooling controls to force outside air into the vehicle. Set the blower at high speed.
80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Defroster Check operation by selecting the defrost mode and place the blower control on high speed. You should be able to feel the air directed against the windshield. Lights Have someone observe the operation of exterior lights while you work the controls. Check turn signal and high beam indicator lights on the instrument panel.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 3 䡵 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85 ▫ Phone Call Features . . . . . . . . . . . . . . . . . . . .98 ▫ Inside Day/Night Mirror — If Equipped . . . . . .85 ▫ UConnect威 System Features . . . . . . . . . . . . . . 101 ▫ Automatic Dimming Mirror — If Equipped . . . .86 ▫ Advanced Phone Connectivity . . . . . . . . . . . . 105 ▫ Electric Remote-Control Mirrors . . . . . . . . . . . .
82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Voice Training . . . . . . . . . . . . . . . . . . . . . . . . 120 䡵 Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121 ▫ Manual Front Seat Adjustments . . . . . . . . . . . 121 ▫ Power Seats — If Equipped . . . . . . . . . . . . . . 124 ▫ Adjustable Head Restraints . . . . . . . . . . . . . . 125 ▫ Heated Seats — If Equipped . . . . . . . . . . . . . 126 ▫ Fold Flat Front Passenger Seat . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Headlights With Wipers (Available With Auto Headlights Only) . . . . . . . . . . . . . . . . . . . . . 139 ▫ Windshield Washers . . . . . . . . . . . . . . . . . . . 140 ▫ Adding Washer Fluid . . . . . . . . . . . . . . . . . . 140 䡵 Tilt/Telescoping Steering Column . . . . . . . . . . . 140 83 䡵 Garage Door Opener — If Equipped . . . . . . . . . 144 ▫ Programming HomeLink威 . . . . . . . . . . . . . . . 146 ▫ Gate Operator/Canadian Programming . . . . .
84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Venting Sunroof - Express . . . . . . . . . . . . . . . 153 ▫ Cupholder Ash Receiver — If Equipped . . . . . 156 ▫ Closing Sunroof - Express . . . . . . . . . . . . . . . 153 䡵 Console Features . . . . . . . . . . . . . . . . . . . . . . . 157 ▫ Auto Sunroof (Express) With Anti–Pinch Protection — If Equipped . . . . . . . . . . . . . . . 153 ▫ Console Features . . . . . . . . . . . . . . . . . . . . . . 157 ▫ Sunshade Operation . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS INSIDE DAY/NIGHT MIRROR — IF EQUIPPED Adjust the mirror to center on the view through the rear window. A two-point pivot system allows for horizontal and vertical mirror adjustment. Adjusting Rear View Mirror 85 Annoying headlight glare can be reduced by moving the small control under the mirror to the night position (toward rear of vehicle). The mirror should be adjusted while set in the day position (toward windshield).
86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE AUTOMATIC DIMMING MIRROR — IF EQUIPPED This mirror will automatically adjust for annoying headlight glare from vehicles behind you. Push in the button on the face of the mirror to activate the dimming feature.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean. 3 ELECTRIC REMOTE-CONTROL MIRRORS Both of the outside mirrors can be adjusted by using the remote controls mounted on the driver’s door panel. The rotary knob has three separate positions: L for the Left mirror; O for Off; and R for the Right mirror.
88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Outside Mirror — Passenger’s Side Adjust the convex outside mirror so you can just see the side of your vehicle in the part of the mirror closest to the vehicle. WARNING! Mirror Directions ADJUSTING SIDEVIEW MIRRORS Outside Mirror — Driver’s Side Adjust the outside mirror to center on the adjacent lane of traffic, with a slight overlap of the view obtained on the inside mirror.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ILLUMINATED VANITY MIRRORS — IF EQUIPPED An illuminated vanity mirror is on each sun visor. To use the mirror, rotate the sun visor down and swing the mirror cover upward. The lights will turn on automatically. Closing the mirror cover turns off the lights. 89 HANDS-FREE COMMUNICATION (UConnect姞) — IF EQUIPPED NOTE: The sales code RER radio contains an integrated Hands-Free Communication (UConnect威) system.
90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: For UConnect威 customer support, visit the following websites: • www.chrysler.com/uconnect • www.dodge.com/uconnect • www.jeep.com/uconnect • or call 1–877–855–8400 UConnect威 allows you to transfer calls between the system and your cellular phone as you enter or exit your vehicle and enables you to mute the system’s microphone for private conversation. The UConnect威 phonebook enables you to store up to 32 names, with four numbers per name.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Recognition Button Actual button location may vary with radio. The individual buttons are described in the “Operation” section. The UConnect威 system can be used with any Hands-Free Profile certified Bluetooth威 cellular phone. See the UConnect威 website for supported phones. If your cellular phone supports a different profile (e.g., Headset Profile) you may not be able to use any UConnect威 features.
92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • For each feature explanation in this section, only the combined form of the voice command is given. You can also break the commands into parts and say each part of the command when you are asked for it. For example, you can use the combined form voice command ⬙Phonebook New Entry,⬙ or you can break the combined form command into two voice commands: ⬙Phonebook⬙ and ⬙New Entry.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE The following are general phone to UConnect威 system pairing instructions: • Press the PHONE button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Setup Phone Pairing.⬙ • When prompted, after the beep, say ⬙Pair a Phone⬙ and follow the audible prompts. • You will be asked to say a four-digit Personal Identification Number (PIN), which you will later need to enter into your cellular phone. You can enter any four-digit PIN.
94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The system will prompt you to say the number you want to call. • The system will prompt you to say the name of the person you want to call. • For example, you can say ⬙234-567-8901.⬙ The phone number that you enter must be of valid length and combination. Based on the country in which the vehicle was purchased, the UConnect威 system limits the user from dialing an invalid combination of numbers. For example, in the U.S.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After the ⬙Ready⬙ prompt and the following beep, say ⬙Phonebook New Entry.⬙ • When prompted, say the name of the new entry. Use of long names helps the voice recognition and it is recommended. For example, say ⬙Robert Smith⬙ or ⬙Robert⬙ instead of ⬙Bob.⬙ • When prompted, enter the number designation (e.g., ⬙Home,⬙ ⬙Work,⬙ ⬙Mobile,⬙ or ⬙Pager⬙). This will allow you to store multiple numbers for each phonebook entry, if desired.
96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Some phones cannot send phonebook entries if they are already connected to any system via Bluetooth威, and you may see a message on the phone display that the Bluetooth威 link is busy. In this case, the user must first disconnect or drop the Bluetooth威 connection to the UConnect威 system, and then send the address book entry via Bluetooth威. Please see your phone Owner’s Manual for specific instructions on how to drop the Bluetooth威 connection.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Delete Entries in the UConnect威 Phonebook NOTE: Editing phonebook entries is recommended when the vehicle is not in motion. • Press the PHONE button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Phonebook Delete.⬙ • After you enter the Phonebook Delete menu, you will then be asked for the name of the entry that you wish to delete.
98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE List All Names in the UConnect威 Phonebook • Press the PHONE button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Phonebook List Names.⬙ • The UConnect威 system will play the names of all the phonebook entries. • To call one of the names in the list, press the “Voice Recognition” button during the playing of the desired name, and say ⬙Call.⬙ NOTE: The user can also exercise ⬙Edit⬙ or ⬙Delete⬙ operations at this point.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Answer or Reject an Incoming Call - Call Currently in Progress If a call is currently in progress and you have another incoming call, you will hear the same network tones for call waiting that you normally hear when using your cell phone. Press the PHONE button to place the current call on hold and answer the incoming call. NOTE: The UConnect威 system compatible phones in the market today do not support rejecting an incoming call when another call is in progress.
100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Three-Way Calling To initiate three-way calling, press the “Voice Recognition” button while a call is in progress, and make a second phone call, as described under ⬙Making a Second Call While Current Call in Progress.⬙ After the second call has established, press and hold the PHONE button until you hear a double beep, indicating that the two calls have been joined into one conference call.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After the ignition key is switched to OFF, a call can continue on the UConnect威 system for a certain duration, after which the call is automatically transferred from the UConnect威 system to the mobile phone. • An active call is automatically transferred to the mobile phone after the ignition key is switched to OFF. UConnect姞 System Features Language Selection To change the language that the UConnect威 system is using: • Press the PHONE button to begin.
102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After the ⬙Ready⬙ prompt and the following beep, say ⬙Emergency⬙ and the UConnect威 system will instruct the paired cellular phone to call the emergency number. This feature is only supported in the U.S. NOTE: The emergency number dialed is based on the country where the vehicle is purchased (911 for the U.S. and Canada and 060 for Mexico). The number dialed may not be applicable with the available cellular service and area.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE certain companies, which time out a little too soon to work properly with the UConnect威 system. Voice Mail Calling To learn how to access your voice mail, refer to ⬙Working with Automated Systems.⬙ Working with Automated Systems This method is used in instances where one generally has to press numbers on the cellular phone keypad while navigating through an automated telephone system.
104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: • You may not hear all of the tones due to cellular phone network configurations; this is normal. • Some paging and voice mail systems have system time out settings that are too short and may not allow the use of this feature. Barge In - Overriding Prompts The “Voice Recognition” button can be used when you wish to skip part of a prompt and issue your voice recognition command immediately.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE dialing a number with your paired Bluetooth威 cellular phone, the audio will be played through your vehicle’s audio system. The UConnect威 system will work the same as if you dial the number using voice recognition. • Following the beep, say ⬙Mute.⬙ NOTE: Certain brands of mobile phones do not send the dial ring to the UConnect威 system to play it on the vehicle audio system, so you will not hear it.
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Connect or Disconnect Link Between the UConnect威 System and Cellular Phone Your cellular phone can be paired with many different electronic devices, but can only be actively ⬙connected⬙ with one electronic device at a time. the lowest priority. To “select” or “delete” a paired phone being announced, press the “Voice Recognition” button and say “Select” or “Delete.” Also, see the next two sections for an alternate way to “select” or “delete” a paired phone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The selected phone will be used for the next phone call. If the selected phone is not available, the UConnect威 system will return to using the highest priority phone present in or near (approximately within 30 ft [9 m]) the vehicle. Delete UConnect威 Paired Cellular Phones • Press the PHONE button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Setup Phone Pairing.⬙ • At the next prompt, say ⬙Delete⬙ and follow the prompts.
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Repeat the words and phrases when prompted by the UConnect威 system. For best results, the Voice Training session should be completed when the vehicle is parked with the engine running, all windows closed, and the blower fan switched OFF. • Speak normally, without pausing, just as you would speak to a person sitting a few feet/meters away from you. This procedure may be repeated with a new user. The system will adapt to the last trained voice only.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • When navigating through an automated system such as voice mail, or when sending a page, at the end of speaking the digit string, make sure to say ⬙Send.⬙ • Storing names in the phonebook when the vehicle is not in motion is recommended. • It is not recommended to store similar sounding names in the UConnect威 phonebook. • The UConnect威 phonebook nametag recognition rate is optimized for the person who stored the name in the phonebook.
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Echo at the far end can sometimes be reduced by lowering the in-vehicle audio volume. • In a convertible vehicle, system performance may be compromised with the convertible top down. Bluetooth威 Communication Link Cellular phones have been found to lose connection to the UConnect威 system. When this happens, the connection can generally be re-established by switching the phone off/on. Your cell phone is recommended to remain in Bluetooth威 ON mode.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 3
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 3
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Primary zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location all Voice Commands Alternate(s) Voice Commands Primary Alternate(s) call cancel confirmation prompts continue delete dial download edit emergency English erase all Espanol Francais help home
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Primary language list names list phones mobile mute mute off new entry no pager pair a phone phone pairing phonebook previous record again redial Voice Commands Alternate(s) pairing phone book Voice Commands Primary Alternate(s) return to main menu return or main menu select phone select send set up phone settings or phone set up towing assistance transfer call UConnect威 Tutorial try again voice training work yes 115 3
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE General Information This device complies with Part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired operation. possible.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 If you ever wish to interrupt the system while it lists options, press the VR hard-key, listen for the beep, and say your command. The system will best recognize your speech if the windows are closed, and the heater/air-conditioning fan is set to low. Pressing the VR hard-key while the system is speaking is known as “barging in.” The system will be interrupted and you can add or change commands. This will become helpful once you start to learn the options.
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Use the ON/OFF VOLUME rotary knob to adjust the volume to a comfortable level while the voice recognition system is speaking. Please note the volume setting for VR is different then the audio system. • NEXT STATION (to select the next station) Main Menu Start a dialogue by pressing the VR hard-key. You may say MAIN MENU to switch to the main menu.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Satellite Radio To switch to satellite radio mode say SAT or SATELLITE RADIO.
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE − CONTINUE (to continue recording) − DELETE (to delete the recording) • PLAY MEMOS (to play previously recorded memos) — During the playback you may press the VR hardkey to stop playing memos.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 SEATS Manual Front Seat Adjustments Forward/Rearward The manual seat adjustment bar is at the front of the seat, near the floor. Pull the bar upward to move the seat forward or rearward. Release the bar once the seat is in the position desired. Then, using body pressure, move forward and rearward on the seat to be sure that the seat adjusters have latched.
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust the seat only while the vehicle is parked. Driver Seat Manual Height Adjuster — If Equipped A lever style height adjustment feature enhances comfort for petite as well as tall drivers.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Reclining Bucket Seats The recliner control is on the side of the seat. To recline, lean forward slightly before lifting the lever, then lean back to the desired position and release the lever. Lean forward and lift the lever to return the seatback to its normal position. 123 WARNING! • Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control.
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Lumbar Support — If Equipped This feature allows you to increase or decrease the amount of lumbar support. The control lever is located on the outboard side of the driver’s seatback. Turn the control lever downward to increase and upward to decrease the desired amount of lumbar support. Power Seats — If Equipped The power seat switches are on the outboard side of the seat near the floor.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Do not place any article under a power seat as it may cause damage to the seat controls. Adjustable Head Restraints Head restraints can reduce the risk of whiplash injury in the event of impact from the rear. Adjust the restraints so that the upper edge is as high as practical. To raise, pull up on the head restraint. To lower, depress the button on the post guide and push down on the head restraint.
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Heated Seats — If Equipped This feature heats leather or cloth front driver and passenger seats. The controls for the heated seats are located in the center console above the climate controls. There are indicator lights in the switches, which indicate a low heat setting (one light lit) or high heat setting (two lights lit). Heated Seat Switches Press the switch once to select high-level heating. Press the switch a second time to select low-level heating.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion or other physical condition must exercise care when using the seat heater. It may cause burns even at low temperatures, especially if used for long periods of time. Do not place anything on the seat that insulates against heat, such as a blanket or cushion. This may cause the seat heater to overheat.
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The hard seatback features a work surface and a molded rim for retaining items stored on the seatback panel. Folding Rear Seat To provide additional storage area, the rear seatback can be folded forward. Pull on the loops shown in the picture to fold down either or both seatbacks. When returning the rear seatback to the upright position, be sure the seatback is latched.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 WARNING! The rear cargo area of the vehicle (with the rear seatbacks in the locked-up or folded down position) should not be used as a play area by children. They could be seriously injured in an accident. Children should be seated and using the proper restraint system. Folding Rear Seat Center Armrest The rear seat is equipped with a folding armrest with cupholders.
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE TO OPEN AND CLOSE THE HOOD To open the hood, two latches must be released. First pull the hood release lever located under the left side of the instrument panel. Then lift the secondary latch located under the front edge of the hood, near the center and raise the hood.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Use the hood prop rod to secure the hood in the open position. Place the upper end of the prop rod in the hole on the left underside of the hood. 131 slam the hood to close it. Use a firm downward push at the center of the hood to ensure that both latches engage. WARNING! If the hood is not fully latched it could fly up when the vehicle is moving and block your forward vision. You could have a collision.
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE automatically. Interior lighting also comes on when a door is opened or the dimmer control is turned fully upward, past the second detent. There is a second light located midway back in the headliner. Headlights, Parking Lights, Instrument Panel Lights Turn the end of the Multifunction Control Lever to the first detent for parking light operation. Turn to the second detent for headlight operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To change the brightness of the instrument panel lights, rotate the center portion of the Multifunction Control Lever up or down. 133 Automatic Headlight System — If Equipped Turning the end of the Multifunction Control Lever to the third detent, “A” (Auto), will activate the automatic headlight system.
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Passing Light / Flash to Pass You can signal another vehicle with your headlights by lightly pulling the Multifunction Control Lever toward you. This will cause the headlights to turn on at high beam and remain on until the lever is released. NOTE: If the Multifunction Control Lever is held in the flash to pass position for more than 15 seconds, the high beams will shut off. If this occurs, wait 30 seconds for the next flash to pass operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 Turn Signals Move the Multifunction Control Lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights. You can signal a lane change by moving the lever partially up or down without moving beyond the detent. Front Fog Light Control NOTE: The front fog lights will only operate with the headlights on low beam. Selecting high beam headlights will turn off the front fog lights.
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If either light remains on and does not flash, or there is a very fast flash rate, check for a defective outside light bulb. If an indicator fails to light when the lever is moved, it would suggest that the fuse or indicator bulb is defective. Highbeam/Lowbeam Select Switch Push the Multifunction Control Lever away from you to switch the headlights to HIGH beam. Pull the Lever toward you, to switch the headlights back to Low beam.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 NOTE: The wipers will automatically return to the PARK position if you turn off the ignition switch while they are operating. The wipers will resume operation when you turn the ignition switch to the ON position again. CAUTION! • Turn the windshield wipers off when driving through an automatic car wash. Damage to the windshield wipers may result if the wiper control is left in any position other than OFF.
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Intermittent Wiper System Use the intermittent wiper system when weather conditions make a single wiping cycle with a variable pause between cycles desirable. Rotate the end of the Windshield Wiper/Washer Control Lever to the first detent, and then turn the end of the lever to select the desired delay interval.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Mist Feature Push down on the wiper control lever to activate a single wipe to clear the windshield of road mist or spray from a passing vehicle. As long as the lever is held down, the wipers will continue to operate.
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Windshield Washers To use the washer, pull the Windshield Wiper/Washer Control lever toward you and hold it for as long as washer spray is desired. If you activate the washer while the wiper control is in the delay range, the wipers will operate in low speed for two wipe cycles after releasing the lever and then resume the intermittent interval previously selected.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 outward or push it inward as desired. To lock the steering column in position, push the control handle inward until fully engaged. WARNING! Do not adjust the steering wheel while driving. The telescoping adjustment must be locked while driving. Adjusting the steering wheel while driving or driving without the telescoping adjustment locked could cause the driver to lose control of the vehicle.
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ELECTRONIC SPEED CONTROL OPERATION The Speed Control Lever is located on the right side of the steering wheel. TO ACTIVATE: Push in and release the ON/OFF button located in the end of the Electronic Speed Control Lever. The Speed Control indicator in the instrument cluster will illuminate. To turn the system OFF, push in and release the ON/OFF button a second time. The Speed Control indicator will turn off. The system should be turned OFF when not in use.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 TO SET AT THE DESIRED SPEED: When the vehicle has reached the desired speed, push down on the lever and release SET DECEL. The vehicle will operate at the selected speed. TO RESUME SPEED: To resume a previously set speed, push upward on the RESUME ACCEL lever and release. Resume can be used at any speed above 20 mph (32 km/h). NOTE: • The vehicle must be traveling at least 25 mph (40 km/h) for the speed control to set.
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Pushing down the SET DECEL button once will result in a 1 mph (2 km/h) speed decrease. Each time the button is pushed, speed decreases. WARNING! Speed Control can be dangerous where the system can’t maintain a constant speed. Your vehicle could go too fast for the conditions, and you could lose control. An accident could be the result. Don’t use Speed Control in heavy traffic or on roads that are winding, icy, snow-covered, or slippery.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE The HomeLink威 buttons that are located in the headliner or sun visor designate the three different HomeLink威 channels. HomeLink威 Buttons NOTE: HomeLink威 is disabled when the Vehicle Security Alarm is active. 145 WARNING! Your motorized door or gate will open and close while you are training the Universal Transceiver. Do not train the transceiver if people or pets are in the path of the door or gate.
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Vehicle exhaust contains carbon monoxide, a dangerous gas. Do not run your vehicle in the garage while training the transceiver. Exhaust gas can cause serious injury or death. Programming HomeLink姞 Before You Begin If you have not trained any of the HomeLink威 buttons, erase all channels before you begin training. Your vehicle should be parked outside of the garage when programming. 1. Turn the ignition switch to the ON/RUN position. 2.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: • Some gate operators and garage door openers may require you to replace Step 3 with procedures noted in the “Gate Operator/Canadian Programming” section. • After training a HomeLink威 channel, if the garage door does not operate with HomeLink威 and the garage door opener was manufactured after 1995, the garage door opener may have a rolling code. If so, proceed to the heading “Programming A Rolling Code System.” 4.
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 7. Return to the vehicle and press the programmed HomeLink威 button twice (holding the button for two seconds each time). If the device is plugged in and activates, programming is complete. If the device does not activate, press the button a third time (for two seconds) to complete the training. If you have any problems, or require assistance, please call toll-free 1–800–355–3515 or, on the Internet at www.HomeLink.com for information or assistance.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 Similar to this Canadian law, some U.S. gate operators are designed to “time-out” in the same manner. Then proceed with Step 4 under “Programming HomeLink威” earlier in this section. It may be helpful to unplug the device during the cycling process to prevent possible overheating of the garage door or gate motor. Using HomeLink姞 To operate, simply press and release the programmed HomeLink威 button. Activation will now occur for the trained device (i.e.
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Without releasing the button, proceed with Programming Homelink威 Step 2 and follow all remaining steps. • Press the “Learn” button on the Garage Door Opener to complete the training for a Rolling Code. Security It is advised to erase all channels before you sell or turn in your vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 NOTE: The transmitter has been tested and it complies with FCC and IC rules. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the device. 3 The term IC before the certification/registration number only signifies that Industry Canada technical specifications were met. POWER SUNROOF — IF EQUIPPED The sunroof controls are mounted between the sun visors in the Dome/Reading Lamp.
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Never leave children in a vehicle, with the keys in the ignition switch. Occupants, particularly unattended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death. • In an accident, there is greater risk of being thrown from a vehicle with an open sunroof. You could also be seriously injured or killed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 Venting Sunroof - Express Press and release the ⬙V⬙ button, and the sunroof will open to the vent position. This is called Express Vent. Sunshade Operation The sunshade can be opened manually. However, the sunshade will open automatically as the sunroof opens. Closing Sunroof - Express Press the switch forward and release, and the sunroof will close automatically from any position. The sunroof will close fully, then stop automatically.
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Sunroof Maintenance Use only a non-abrasive cleaner and a soft cloth to clean the glass panel. ELECTRICAL POWER OUTLETS There are two 12-volt electrical outlets on this vehicle. Both of the outlets are protected by a fuse. Ignition Off Operation For vehicles not equipped with the Electronic Vehicle Information Center (EVIC), the power sunroof switch will remain active for 45 seconds after the ignition switch is turned off.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 3 Instrument Panel Power Outlet The center console power outlet is powered directly from the battery (power available at all times). Items plugged into this outlet may discharge the battery and/or prevent engine starting.
156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Electrical Outlet Use With Engine Off CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting. • Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.) will degrade the battery even more quickly.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! For vehicles equipped with the heated and cooled cupholder, locate the cup holder ash receiver in the forward cupholder. The optional ash receiver also comes with a cigar lighter. You may use the power outlet, located in the instrument panel below the climate control knobs, or in the bottom of the console compartment, for this cigar lighter.
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Dual Storage Bins Lifting a latch at the front of the hinged armrest provides access to these storage areas. 1. The left latch opens to the top storage area. 2. The lower bin can be accessed directly, without first exposing the upper bin, by operating the right latch with the armrest down. 3. The first storage bin can be used to hold smaller items. 4.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 Video Console — If Equipped The optional VES™(Video Entertainment System) includes the following components: • The screen for a rear seat DVD player is stored under the armrest. 3 • Remote Control • Audio/Video RCA Jacks Video Console See Section Four, “Video Entertainment System-If Equipped,” of this manual, for further information.
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CUPHOLDERS Heated Or Cooled Cupholder — If Equipped With this feature the rear cavity of the cupholder can keep cool beverages cool, and hot beverages hot. The rear cupholder heats to 140°F (60°C) or cools to 35°F (1.6°C). The switch is located on the front of the center console and has three positions: HEAT, OFF, COOL. When the unit is on and the LED is Red, the cup holder is being heated. When the LED is Blue, the cup holder is being cooled.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 CAUTION! Make sure the beverage container can withstand the temperatures shown above, when using the Cooled or Heated Cupholder. 3 Rear Bottle Holders There are built-in bottle holders located in both rear door trim panels.
162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! WARNING! If containers of hot liquid are placed in the bottle holder, they can spill when the door is closed, burning the occupants. Be careful when closing the doors to avoid injury. • Be certain that the seatback is securely locked into position. If the seatback in not securely locked into position, the seat will not provide the proper stability for child seats and/or passengers. An improperly latched seat could cause serious injury.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • The weight and position of cargo and passengers can change the vehicle center of gravity and vehicle handling. To avoid loss of control resulting in personal injury, follow these guidelines for loading your vehicle: • Always place cargo evenly on the cargo floor. Put heavier objects as low and as far forward as possible. 163 • Place as much cargo as possible in front of the rear axle.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 Instrument Panel Features . . . . . . . . . . . . . . . . . 169 ▫ Compass Display . . . . . . . . . . . . . . . . . . . . . 187 䡵 Base Instrument Cluster . . . . . . . . . . . . . . . . . . 170 ▫ Personal Settings (Customer Programmable Features) . . . . . . . . . . . . . . . . . . . . . . . . . . . 190 䡵 Premium Instrument Cluster . . . . . . . . . . . . . . . 171 䡵 Instrument Cluster Descriptions . . . . . . . . . . . .
166 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ FM Reception . . . . . . . . . . . . . . . . . . . . . . . . 194 ▫ Notes On Playing MP3/WMA Files . . . . . . . . 217 䡵 Sales Code RES — AM/FM Stereo Radio With CD Player (MP3 AUX Jack) . . . . . . . . . . . . . . . . 194 ▫ List Button (Disc Mode For MP3/WMA Play) . . . . . . . . . . 220 ▫ Operating Instructions - Radio Mode . . . . . . . 195 ▫ Info Button (Disc Mode For MP3/WMA Play) . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 䡵 Sales Code RER — Multimedia System — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . 225 ▫ Operating Instructions — Satellite Radio . . . . . 227 ▫ Operating Instructions — Hands-Free Communication (UConnect威) (If Equipped) . . . 227 ▫ Clock Setting Procedure . . . . . . . . . . . . . . . . . 227 䡵 Universal Consumer Interface (UCI) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . 229 ▫ Connecting The iPod威 Device . . . . . . . . .
168 UNDERSTANDING YOUR INSTRUMENT PANEL 䡵 Video Entertainment System (VES)威 — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . 240 ▫ Automatic Temperature Control (ATC) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 248 䡵 Radio Operation And Cellular Phones . . . . . . . . 242 ▫ Operating Tips . . . . . . . . . . . . . . . . . . . . . . . 254 䡵 CD/DVD Disc Maintenance . . . . . . . . . . . . . . . 242 䡵 Rear Window Features . . . . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 169 INSTRUMENT PANEL FEATURES 4 1 2 3 4 5 — Air Outlet — Side Window Demister Outlet — Instrument Cluster — Ignition Switch — Analog Clock 6 — Radio 7 — Passenger Airbag 8 — Glove Box 9 — Heated Seat Switch* 10 — Hazard Switch 11 — Storage Compartment 12 — Climate Control 13 — Trunk Release Switch * If Equipped
170 UNDERSTANDING YOUR INSTRUMENT PANEL BASE INSTRUMENT CLUSTER
UNDERSTANDING YOUR INSTRUMENT PANEL 171 PREMIUM INSTRUMENT CLUSTER 4
172 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTIONS 1. Fuel Gauge When the ignition switch is in the ON position, the pointer will show the level of fuel remaining in the fuel tank. 2. Fuel Door Reminder This is a reminder that the Fuel Filler Door is located on the left side of the vehicle. 3. Temperature Gauge The temperature gauge shows engine coolant temperature. Any reading below the red area of the gauge shows that the engine cooling system is operating properly.
UNDERSTANDING YOUR INSTRUMENT PANEL 173 5. Low Fuel Light When the fuel level drops to two gal (7.6 L), the fuel symbol will light and a single chime will sound. come on during starting, stays on, or comes on while driving, have the system checked by an authorized dealer. 6. Charging System Light This light shows the status of the electrical charging system. The light should come on briefly when the ignition is first turned ON and remain on briefly as a bulb check.
174 UNDERSTANDING YOUR INSTRUMENT PANEL will turn off after the engine is started. If the bulb does not come on during starting, have the system checked by an authorized dealer. If the light comes on and remains on while driving, stop the vehicle and shut off the engine. DO NOT OPERATE THE VEHICLE UNTIL THE CAUSE IS CORRECTED. The light does not show the quantity of oil in the engine. This can be determined using the procedure shown in Section 7. 11.
UNDERSTANDING YOUR INSTRUMENT PANEL The two trip odometers show individual trip mileage. To switch from odometer to trip odometers, press and release the Trip Odometer button. To reset a trip odometer, display the desired trip odometer to be reset then push and hold the button until the display resets (approximately two seconds). Refer to “Trip Odometer Button” for additional information.
176 UNDERSTANDING YOUR INSTRUMENT PANEL indicator system is duty cycle based, which means the engine oil change interval may fluctuate dependent upon your personal driving style. NOTE: If the indicator message illuminates when you start the vehicle, the oil change indicator system did not reset. If necessary repeat this procedure. Unless reset, this message will continue to display each time you turn the ignition switch to the ON position.
UNDERSTANDING YOUR INSTRUMENT PANEL Dual Trip Odometer — If Equipped Press and release this button to change the display from odometer to “Trip A.” Press and release it a second time to change the display to “Trip B.” Press and release it a third time to change the display back to the odometer. To reset the trip odometer, first display the trip mileage that you want to reset, “Trip A” or “Trip B.” Then push and hold the button (approximately two seconds) until the display resets to zero.
178 UNDERSTANDING YOUR INSTRUMENT PANEL 19. Brake System Warning Light This light monitors various brake functions, including brake fluid level and parking brake application. If the brake light turns on, it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the anti-lock brake system (if equipped). The dual brake system provides a reserve braking capacity in the event of a failure to a portion of the hydraulic system.
UNDERSTANDING YOUR INSTRUMENT PANEL the ON position. The light should illuminate for approximately two seconds. The light should then turn off unless the parking brake is applied or a brake fault is detected. If the light does not illuminate, have the light inspected by an authorized dealer. The light also will turn on when the parking brake is applied with the ignition switch in the ON position. NOTE: This light shows only that the parking brake is applied.
180 UNDERSTANDING YOUR INSTRUMENT PANEL is not functioning and that service is required, however, the conventional brake system will continue to operate normally provided that the BRAKE warning light is not on. has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if underinflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale. Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is combined with the low tire pressure telltale.
182 UNDERSTANDING YOUR INSTRUMENT PANEL (Refer to “Tire Inflation Pressures” under “Tires — General Information” and to “Tire Pressure Monitor System (TPMS)” in Section 5 of this manual for more information). 25. Malfunction Indicator Light This light is part of an onboard diagnostic system called OBD that monitors emissions, engine, and automatic transaxle control systems. The light will illuminate when the key is in the ON/RUN position before engine start.
UNDERSTANDING YOUR INSTRUMENT PANEL ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) – IF EQUIPPED 183 The Electronic Vehicle Information Center (EVIC) features a driver-interactive display. It is located in the lower left part of the cluster below the fuel and engine temperature gauges.
184 UNDERSTANDING YOUR INSTRUMENT PANEL The system allows the driver to select information by pressing the following buttons on the instrument panel switch bank: Press and release the MENU button to advance the display to Trip Functions or Personal settings or to return to the default System status MENU display. Button Press and release the STEP button to advance the display through the various Trip Functions or Personal settings.
UNDERSTANDING YOUR INSTRUMENT PANEL • RKE (Remote Keyless Entry) Battery Low (with a single chime) • Personal Settings Not Available – Vehicle Not In PARK.
186 UNDERSTANDING YOUR INSTRUMENT PANEL 2. Fully depress the accelerator pedal slowly three times within 10 seconds. The Trip Functions mode displays the following information: 3. Turn the ignition switch to the LOCK position. • Average Fuel Economy Shows the average fuel economy since the last reset. When the fuel economy is reset, the display will read, RESET or show dashes for two seconds.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Significant changes in driving style or vehicle loading will greatly affect the actual drivable distance of the vehicle, regardless of the DTE display value. • When the DTE value is less than 30 mi (48 km) estimated driving distance, the DTE display will change to a text display of ⬙LOW FUEL. This display will continue until the vehicle runs out of fuel.
188 UNDERSTANDING YOUR INSTRUMENT PANEL Automatic Compass Calibration This compass is self-calibrating, which eliminates the need to calibrate the compass manually. When the vehicle is new, the compass may appear erratic and the EVIC will flash the “CAL” indicator until the compass is calibrated. You may calibrate the compass by completing one or more 360 degree turns (in an area free from large metal or metallic objects) until the CAL indicator in the EVIC turns off.
UNDERSTANDING YOUR INSTRUMENT PANEL Compass Variance Compass Variance is the difference between magnetic North and Geographic North. In some areas of the country, the difference between magnetic and geographic North is great enough to cause the compass to give false readings. If this occurs, the compass variance must be set using the following procedure: NOTE: Magnetic materials and cell phones should be kept away from the top of the Instrument Panel. This is where the compass sensor is located.
190 UNDERSTANDING YOUR INSTRUMENT PANEL 1. Turn the ignition switch to the ON position. Leave the selector lever in PARK. 2. Press and release the MENU button until “Personal Settings” displays in the EVIC. 3. Press and release the STEP button until “Compass Variance” and the current Variance Value displays in the EVIC. 4. Press and release the RESET button to increment the Variance Value by one, (one button press per update), until the proper variance zone is selected according to the map.
UNDERSTANDING YOUR INSTRUMENT PANEL Auto Unlock on Exit When ON is selected and the transaxle is in the PARK or NEUTRAL position, all doors will unlock when the driver’s door is opened. To make your selection, press and hold the RESET button until ON or OFF appears. Remote Key Unlock When “Driver Door 1st Press” is selected, only the driver’s door will unlock on the first press of the remote keyless entry unlock button.
192 UNDERSTANDING YOUR INSTRUMENT PANEL Headlights With Wipers (Available with Auto Headlights Only) When ON is selected, and the headlight switch is in the AUTO position, the headlights will turn on approximately 10 seconds after the wipers are turned on. The headlights will also turn off when the wipers are turned off if they were turned on by this feature. To make your selection, press and hold the RESET button until ON or OFF appears.
UNDERSTANDING YOUR INSTRUMENT PANEL SETTING THE ANALOG CLOCK To set the analog clock, located at the top center of the instrument panel, press and hold the button in until the setting is correct. The clock will adjust slowly at first and then quicker the longer the button is held. 193 you understand and save you concern about these “apparent” malfunctions, you must understand a point or two about the transmission and reception of radio signals.
194 UNDERSTANDING YOUR INSTRUMENT PANEL AM Reception AM sound is based on wave amplitude, so AM reception can be disrupted by such things as lightning, power lines and neon signs. SALES CODE RES — AM/FM STEREO RADIO WITH CD PLAYER (MP3 AUX JACK) NOTE: The radio sales code is located on the lower right side of your radio faceplate.
UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Control (Rotary) Push the ON/VOLUME control knob to turn on the radio. Push the ON/VOLUME control knob a second time to turn off the radio. Electronic Volume Control The electronic volume control turns continuously (360 degrees) in either direction without stopping.
196 UNDERSTANDING YOUR INSTRUMENT PANEL If your vehicle is not equipped with or this feature is not available on your vehicle, a “Not Equipped With UConnect” message will display on the radio screen. Phone Button (UConnect威 Hands-Free Phone) — If Equipped Press this button to operate the Hands-Free Phone (UConnect威) feature (if equipped). Refer to “Hands-Free Communication (UConnect威)” in Section 3.
UNDERSTANDING YOUR INSTRUMENT PANEL 197 INFO Button Press the INFO button for an RDS station (one with call letters displayed). The radio will return a Radio Text message broadcast from an FM station (FM mode only). Push the rotary TUNE/SCROLL control knob a second time and MID will display. Turn the TUNE/SCROLL control knob to the right or left to increase or decrease the mid-range tones.
198 UNDERSTANDING YOUR INSTRUMENT PANEL Push the rotary TUNE/SCROLL control knob again to exit setting tone, balance, and fade. MUSIC TYPE Button Pressing this button once will turn on the Music Type mode for five seconds. Pressing the MUSIC TYPE button or turning the TUNE/SCROLL control knob within five seconds will allow the program format type to be selected. Many radio stations do not currently broadcast Music Type information.
UNDERSTANDING YOUR INSTRUMENT PANEL Program Type Soft Soft Rock Soft Rhythm and Blues Sports Talk Top 40 Weather 16-Digit Character Display Soft Soft Rck Soft R&B Sports Talk Top 40 Weather By pressing the SEEK button when the Music Type icon is displayed, the radio will be tuned to the next frequency station with the same selected Music Type name. The Music Type function only operates when in the FM mode.
200 UNDERSTANDING YOUR INSTRUMENT PANEL selected within five seconds after pressing the SET button, the station will continue to play but will not be stored into pushbutton memory. DISC Button Pressing the DISC button will allow you to switch from AM/FM modes to Disc modes. You may add a second station to each pushbutton by repeating the above procedure with this exception: Press the SET button twice and SET 2 will show in the display window. Each button can be set for SET 1 and SET 2 in both AM and FM.
UNDERSTANDING YOUR INSTRUMENT PANEL Inserting Compact Disc(s) Gently insert one CD into the CD player with the CD label facing up. The CD will automatically be pulled into the CD player and the CD icon will illuminate on the radio display. If a CD does not go into the slot more than an inch (2.5 cm), a disc may already be loaded and must be ejected before a new disc can be loaded.
202 UNDERSTANDING YOUR INSTRUMENT PANEL If you have ejected a disc and have not removed it within 10 seconds, it will be reloaded. If the CD is not removed, the radio will reinsert the CD but will not play it. TIME Button Press this button to change the display from a large CD playing time display to a small CD playing time display. A disc can be ejected with the radio and ignition OFF. RW/FF Press the RW button to stop the CD at the beginning of the current CD track/title.
UNDERSTANDING YOUR INSTRUMENT PANEL 203 Press the right SEEK button to move to the next randomly selected track. files properly and may be unable to play the file normally. UDF and Apple HFS formats are not supported. Press the RND button a second time to stop Random Play. The radio uses the following limits for file systems: Notes On Playing MP3 Files The radio can play MP3 files; however, acceptable MP3 file recording media and formats are limited.
204 UNDERSTANDING YOUR INSTRUMENT PANEL • Level 2: 31 (including a separator ⬙.⬙ and a threecharacter extension) Multisession disc formats are supported by the radio. Multisession discs may contain combinations of normal CD audio tracks and computer files (including MP3 files). Discs created with an option such as ⬙keep disc open after writing⬙ are most likely multisession discs. The use of multisession for CD audio or MP3 playback may result in longer disc loading times.
UNDERSTANDING YOUR INSTRUMENT PANEL Playback of MP3 Files When a medium containing MP3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3 files.
206 UNDERSTANDING YOUR INSTRUMENT PANEL Press and hold the INFO button again for three seconds to return to ⬙elapsed time⬙ display. Operation Instructions - Auxiliary Mode The auxiliary (AUX) jack is an audio input jack, which allows the user to plug in a portable device such as an MP3 player, or cassette player, and utilize the vehicle’s audio system to amplify the source and play through the vehicle speakers. Pressing the AUX button will change the mode to auxiliary device if the AUX jack is connected.
UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE REQ — AM/FM STEREO RADIO AND 6–DISC CD/DVD CHANGER (MP3/WMA AUX JACK) NOTE: The radio sales code is located on the lower right side of your radio faceplate. 207 Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Control (Rotary) Push the ON/VOLUME control knob to turn on the radio. Press the ON/VOLUME control knob a second time to turn off the radio.
208 UNDERSTANDING YOUR INSTRUMENT PANEL to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations without stopping until you release it. SCAN Button Pressing the SCAN button causes the tuner to search for the next listenable station, in AM, FM or Satellite (if equipped) frequencies, pausing for five seconds at each listenable station before continuing to the next.
UNDERSTANDING YOUR INSTRUMENT PANEL 3. After adjusting the hours, press the right side TUNE/ SCROLL control knob to set the minutes. The minutes will begin to blink. 4. Adjust the minutes using the right side TUNE/ SCROLL control knob. Press the TUNE/SCROLL control knob to save the time change. 5. To exit, press any button/knob or wait five seconds. The clock can also be set by pressing the SETUP button and selecting the “SET HOME CLOCK” entry.
210 UNDERSTANDING YOUR INSTRUMENT PANEL Push the rotary TUNE/SCROLL control knob a third time and TREBLE will display. Turn the TUNE/SCROLL control knob to the right or left to increase or decrease the treble tones. or turning the TUNE/SCROLL control knob within five seconds will allow the program format type to be selected. Many radio stations do not currently broadcast Music Type information. Push the rotary TUNE/SCROLL control knob a fourth time and BALANCE will display.
UNDERSTANDING YOUR INSTRUMENT PANEL Program Type Jazz News Nostalgia Oldies Personality Public Rhythm and Blues Religious Music Religious Talk Rock Soft Soft Rock Soft Rhythm and Blues 16-Digit Character Display Jazz News Nostalga Oldies Persnlty Public R&B Rel Musc Rel Talk Rock Soft Soft Rck Soft R&B Program Type Sports Talk Top 40 Weather 211 16-Digit Character Display Sports Talk Top 40 Weather By pressing the SEEK button when the Music Type icon is displayed, the radio will be tuned to the next f
212 UNDERSTANDING YOUR INSTRUMENT PANEL SETUP Button Pressing the SETUP button allows you to select between the following items: • Subtitle – Repeatedly pressing SELECT will switch subtitles to different subtitle languages that are available on the disc (if equipped). NOTE: Turn the TUNE/SCROLL control knob to scroll through the entries. Push the AUDIO/SELECT button to select an entry and make changes.
UNDERSTANDING YOUR INSTRUMENT PANEL • VES威 Lock - Locks out rear VES威 remote controls (if equipped). • VES威 CH1/CH2 - Allows the user to change the mode of either the IR1 or IR2, wireless headphones by pressing the AUDIO/SELECT button (if equipped). • Set Home Clock - Pressing the SELECT button allows you to set the clock. Turn the TUNE/SCROLL control knob to adjust the hours and then press and turn the TUNE/SCROLL control knob to adjust the minutes.
214 UNDERSTANDING YOUR INSTRUMENT PANEL the TUNE/SCROLL control knob to scroll up and down to select the number and then push to select. Subtitles — If Equipped Selecting this item allows you to choose between subtitle Off or On. Audio DRC — If Equipped Selecting this item allows you to limit maximum audio dynamic range. The default is set to ⬙High,⬙ and under this setting, dialogues will play at 11 db higher than if the setting is ⬙Normal.
UNDERSTANDING YOUR INSTRUMENT PANEL Select the button (1-6) you wish to lock onto this station and press and release that button. If a button is not selected within five seconds after pressing the SET button, the station will continue to play but will not be stored into pushbutton memory. You may add a second station to each pushbutton by repeating the above procedure with this exception: Press the SET button twice and SET 2 will show in the display window.
216 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! The radio may shut down during extremely hot conditions. When this occurs, the radio will indicate “Disc Hot” and shut off until a safe temperature is reached. This shutdown is necessary to protect the optics of the DVD player and other radio internal components. NOTE: The ignition switch must be in the ON or ACC position to operate the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL Press and hold the EJECT button for five seconds and all CDs will be ejected from the radio. The disc can be ejected with the radio and ignition OFF. SEEK Button (CD MODE) Press the right SEEK button for the next selection on the CD. Press the left SEEK button to return to the beginning of the current selection, or return to the beginning of the previous selection if the CD is within the first second of the current selection.
218 UNDERSTANDING YOUR INSTRUMENT PANEL Supported Medium Formats (File Systems) The medium formats supported by the radio are ISO 9660 Level 1 and Level 2 and includes the Joliet extension. When reading discs recorded using formats other than ISO 9660 Level 1 and Level 2, the radio may fail to read files properly and may be unable to play the file normally. UDF and Apple HFS formats are not supported. Multisession disc formats are supported by the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL frequencies in the following table are supported. In addition, variable bit rates (VBR) are also supported. The majority of MP3/WMA files use a 44.1 kHz sampling rate and a 192, 160, 128, 96 or VBR bit rates. MPEG Specification Sampling Frequency (kHz) Bit Rate (kbps) 320, 256, 224, 192, 160, 128, 112, 96, 80, 64, 56, 48 160, 128, 144, 112, 96, 80, 64, 56, 48 MPEG-1 Audio Layer 3 48, 44.1, 32 MPEG-2 Audio Layer 3 24, 22.
220 UNDERSTANDING YOUR INSTRUMENT PANEL • Number of files and folders - Loading times will increase with more files and folders To increase the speed of disc loading, it is recommended to use CD-R media and single-session discs. To create a single-session disc, enable the “Disc at Once” option before writing to the disc. LIST Button (DISC Mode for MP3/WMA Play) Pressing the LIST button will bring up a list of all folders on the disc.
UNDERSTANDING YOUR INSTRUMENT PANEL Pressing the AUX button will change the mode to auxiliary device if the AUX jack is connected. NOTE: The AUX device must be turned on and the device’s volume set to the proper level. If the AUX audio is not loud enough, turn the device’s volume up. If the AUX audio sounds distorted, turn the device’s volume down. SEEK Button (Auxiliary Mode) No function. SCAN Button (Auxiliary Mode) No function. EJECT Button (Auxiliary Mode) No function.
222 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions - Hands-Free Phone (UConnect威) (If Equipped) Refer to “Hands-Free Communication (UConnect威)” in Section 3. Operating Instructions - Satellite Radio Mode (If Equipped) Refer to “Satellite Radio” in this section. Operating Instructions - Video Entertainment System (VES威) (If Equipped) Refer to separate “Video Entertainment System (VES威) Guide.” Dolby威 Manufactured under license from Dolby威 Laboratories.
UNDERSTANDING YOUR INSTRUMENT PANEL 223 “JukeBox” (virtual CD changer). Sirius Satellite Radio is optional. The 6.5 in (16.5 cm) touch screen allows for easy menu selection. models, a dual display screen operation. Refer to your Radio-specific user’s manual for detailed operating instructions. A 20-gigabyte HDD allows uploads of music and photos from CDs or through the USB port. The Gracenote database finds the artist, track, and title for the music.
224 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions — Hands-Free Communication (UConnect姞) (If Equipped) Refer to “Hands-Free Communication (UConnect威)” in Section 3. Clock Setting Procedure Setting the Clock 1. Turn on the multimedia system. 2. Touch the screen where the time is displayed. The clock setting menu will appear on the screen. 3. To move the hour forward, touch the screen where the word “Hour” with the arrow pointing upward is displayed.
UNDERSTANDING YOUR INSTRUMENT PANEL Show Time if Radio is Off When selected, this feature will display the time of day on the touch screen when the multimedia system is turned off. Proceed as follows to change the current setting: 1. Turn on the multimedia system. 2. Touch the screen where the time is displayed. The clock setting menu will appear on the screen. 3. When this feature is on, a check mark will appear in the box next to the words “Show Time if Radio is Off.
226 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: If your vehicle is not equipped with UConnect威, the unit will respond with a “Not Equipped With UConnect威” message when selecting controls related to this feature. A 6.5 in (16.5 cm) touch screen allows easy menu selection, while the Advanced Voice Dialog System recognizes more than 1,000 words for audio, navigation, entertainment, and hands-free mobile phone use.
UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions — Satellite Radio Refer to your “Navigation User’s Manual” for detailed operating instructions. Operating Instructions — Hands-Free Communication (UConnect姞) (If Equipped) Refer to your “Navigation User’s Manual” for detailed operating instructions. Clock Setting Procedure The GPS receiver in this system is synchronized to the time data being transmitted by the GPS satellites. The satellites’ clock is Greenwich Mean Time (GMT).
228 UNDERSTANDING YOUR INSTRUMENT PANEL Changing Daylight Savings Time When selected, this feature will display the time of day in daylight savings time. Proceed as follows to change the current setting: 2. Touch the screen where the time is displayed. The clock setting menu will appear on the screen. If the words “Time: User Clock” are displayed at the top of the screen, proceed to Step 4. Otherwise, proceed to Step 3. 1. Turn on the multimedia system. 3.
UNDERSTANDING YOUR INSTRUMENT PANEL 229 6. To save the new time setting, touch the screen where the word “Save” is displayed. UNIVERSAL CONSUMER INTERFACE (UCI) — IF EQUIPPED Show Time if Radio is Off When selected, this feature will display the time of day on the touch screen when the system is turned off. Proceed as follows to change the current setting: NOTE: This section is for sales code RES and REQ radios only with UConnect威.
230 UNDERSTANDING YOUR INSTRUMENT PANEL • the iPod威 battery charges when plugged into the UCI connector. Connecting The iPod姞 Device Use the optional connection cable to connect an iPod威 to the vehicle’s UCI connector (which is located in the glove box on some vehicles. This location may vary with vehicle).
UNDERSTANDING YOUR INSTRUMENT PANEL RW (Rewind) Button Press and hold the RW button to move backward in the current track. Holding the RW button long enough will take you back to the beginning of the current track. Pressing and releasing the RW button will go back five seconds of the current track. FF (Fast Forward) Button Press and hold the FF button to move forward in the current track. Pressing and releasing the FF button will go forward five seconds of the current track.
232 UNDERSTANDING YOUR INSTRUMENT PANEL SCAN Button Pressing the SCAN button will play the first five seconds of each track in the current list and then forward to the next song. To stop the SCAN mode and start playing the desired track, press the SCAN button again. During the SCAN mode, you can also press the SEEK button to the left or right to go to the previous or next tracks.
UNDERSTANDING YOUR INSTRUMENT PANEL Radio Preset Buttons In the List mode, the radio preset buttons are used as shortcuts to the following lists on the iPod威 device. • 1 – Playlists • 2 – Artists • 3 – Albums • 4 – Genres • 5 - Audiobooks • 6 – Podcasts After pressing a preset button, you will see the list you are in on the top line and the first item in that list on the second line. To exit the List mode without selecting a track, press the same preset button again to go back to Play mode.
234 UNDERSTANDING YOUR INSTRUMENT PANEL SATELLITE RADIO — IF EQUIPPED (REN/REQ/RER/RES RADIOS ONLY) Satellite radio uses direct satellite-to-receiver broadcasting technology to provide clear digital sound, coast to coast. The subscription service provider is Sirius Satellite Radio. This service offers over 130 channels of music, sports, news, entertainment, and programming for children, directly from its satellites and broadcasting studios.
UNDERSTANDING YOUR INSTRUMENT PANEL Sirius ID number will display. The Sirius ID number display will time out in two minutes. Press any button on the radio to exit this screen. ESN/SID Access With RER/REN Radios While in SAT mode, press the MENU button on the radio faceplate. Next touch the SUBSCRIPTION tab on the touch screen. All the ESNs that apply to your vehicle will be displayed. Selecting Satellite Mode Press the SAT button until ⬙SAT⬙ appears in the display.
236 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions - Satellite Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. SEEK Buttons Press and release the SEEK buttons to search for the next channel in Satellite mode. Press the right switch to seek up and the left switch to seek down. The radio will remain tuned to the new channel until you make another selection. Holding either button will bypass channels without stopping until you release it.
UNDERSTANDING YOUR INSTRUMENT PANEL or turning the TUNE/SCROLL control knob within five seconds will allow the program format type to be selected. Toggle the MUSIC TYPE button again to select the music type. By pressing the SEEK button when the Music Type function is active, the radio will be tuned to the next channel with the same selected Music Type name.
238 UNDERSTANDING YOUR INSTRUMENT PANEL pushbutton memory. The channels stored in SET 2 memory can be selected by pressing the pushbutton twice. Every time a preset button is used, a corresponding button number will display. REMOTE SOUND SYSTEM CONTROLS — IF EQUIPPED The remote sound system controls are located on the rear surface of the steering wheel. Reach behind the wheel to access the switches.
UNDERSTANDING YOUR INSTRUMENT PANEL The right hand control is a rocker type switch with a push button in the center. Pressing the top of the switch will increase the volume and pressing the bottom of the switch will decrease the volume. The button located in the center of the right hand control will switch modes to Radio or CD. The left hand control is a rocker type switch with a push button in the center. The function of the left hand control is different depending on mode.
240 UNDERSTANDING YOUR INSTRUMENT PANEL VIDEO ENTERTAINMENT SYSTEM (VES)姞 — IF EQUIPPED The optional Video Entertainment System (VES)威 includes the following components for rear seat entertainment: • A diagonal 7 in (17.8 cm) Liquid Crystal Display (LCD) screen integrated into the center console armrest. The screen features brightness control for optimum daytime and nighttime viewing.
UNDERSTANDING YOUR INSTRUMENT PANEL 241 • A battery-powered infrared remote control snaps into a molded compartment in the center console armrest upper storage bin. 4 VES威 Video Screen NOTE: Close the armrest after the LCD screen has been raised to its viewing position. • The touch screen radio and DVD player controls allow front seat operation for easy setup in the case of younger rear seat passengers.
242 UNDERSTANDING YOUR INSTRUMENT PANEL Audio/Video RCA Jacks (AUX Jacks) on the rear of the center console enable the monitor to display video directly from a video camera, connect video games for display on the screen, or play music directly from an MP3 player. 1. Video in (yellow) 2. Left audio in (white) 3. Right audio in (red) NOTE: Refer to your “Vehicle Entertainment System (VES)威 Users Manual” for detailed operating instructions.
UNDERSTANDING YOUR INSTRUMENT PANEL 3. Do not apply paper, paper CD labels, or tape to the disc; avoid scratching the disc. 4. Do not use solvents such as benzine, thinner, cleaners, or antistatic sprays. 243 CLIMATE CONTROLS The Air Conditioning and Heating System is designed to make you comfortable in all types of weather. Manual Air Conditioning and Heating System 5. Store the disc in its case after playing. 6. Do not expose the disc to direct sunlight. 4 7.
244 UNDERSTANDING YOUR INSTRUMENT PANEL Blower Control Temperature Control Rotate this control to regulate the amount of air forced through the ventilation system in any mode. The blower speed increases as you move the control to the right from the “O” (Off) position. There are four blower speeds. Rotate this control to regulate the temperature of the air inside the passenger compartment.
UNDERSTANDING YOUR INSTRUMENT PANEL Mode Control (Air Direction) Rotate this control to choose from several patterns of air distribution. You can select either a primary mode as identified by the symbols on the control, or a blend of two of these modes. The closer the setting is to a particular symbol, the more air distribution you receive from that mode. Panel Air is directed through the outlets in the instrument panel. These outlets can be adjusted to direct airflow.
246 UNDERSTANDING YOUR INSTRUMENT PANEL Defrost Air is directed through the windshield and side window demist outlets. Use this mode with maximum blower and temperature settings for best windshield and side window defrosting. NOTE: The air conditioning compressor operates in Mix and Defrost, or a blend of these modes, even if the Air Conditioning Snowflake button is not pressed. This dehumidifies the air to help dry the windshield. To improve fuel economy, use these modes only when necessary.
UNDERSTANDING YOUR INSTRUMENT PANEL • The use of the recirculation mode in cold or damp weather will cause windows to fog on the inside, because of moisture build-up inside the vehicle. Select the Outside Air position for maximum defogging. • The A/C will engage automatically to prevent fogging when the recirculation button is pressed and the mode control is set to panel or panel / floor. • The A/C can be deselected manually without disturbing the mode control selection.
248 UNDERSTANDING YOUR INSTRUMENT PANEL • ECONOMY MODE If economy mode is desired, press the A/C button to turn off the indicator light and the A/C compressor. Then, move the temperature control to the desired temperature. Automatic Temperature Control (ATC) — If Equipped Automatic Temperature Control Automatic Operation The Infrared Climate Control System automatically maintains the climate in the cabin of the vehicle at the comfort levels desired by the driver and passenger.
UNDERSTANDING YOUR INSTRUMENT PANEL accomplish this, the system gathers information from the cabin infrared sensor mounted between the sun-visors and from various sensors located throughout the vehicle. The controls on the climate control provide the system with operator input. Other sensors take account of vehicle speed, A/C pressure, outside temperature, and engine cooling temperature.
250 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: • The temperature setting can be adjusted at any time without affecting automatic operation. • Pressing the Air Conditioning Control button while in AUTO mode will cause the LED in the control button to flash three times and then turn off. This indicates that the system is in AUTO mode and requesting the air conditioning is not necessary.
UNDERSTANDING YOUR INSTRUMENT PANEL 251 4
252 UNDERSTANDING YOUR INSTRUMENT PANEL The operator can override the AUTO mode setting to change airflow distribution by rotating the Mode Control knob (on the right) to one of the following positions. • Panel Air is directed through the outlets in the instrument panel. These outlets can be adjusted to direct airflow. NOTE: The center instrument panel outlets can be aimed so that they are directed toward the rear seat passengers for maximum airflow to the rear.
UNDERSTANDING YOUR INSTRUMENT PANEL • Air Conditioner Control Press this button to turn on the air conditioning during manual operation only. When the air conditioning is turned on, cool dehumidified air will flow through the outlets selected with the Mode control dial. Press this button a second time to turn off the air conditioning. An LED in the button illuminates when manual compressor operation is selected. • Recirculation Control The system will automatically control recirculation.
254 UNDERSTANDING YOUR INSTRUMENT PANEL Recirculation to be selected while in floor, defrost, or defrost/floor mode. Attempting to use the recirculation while in these modes will cause the LED in the control button to blink and then turn off. • Most of the time, when in Automatic Operation, you can temporarily put the system into Recirculation Mode by pressing the Recirculation Button. However, under certain conditions, while in Automatic Mode, the system is blowing air out the defrost vents.
UNDERSTANDING YOUR INSTRUMENT PANEL 255 Vacation Storage Anytime you store your vehicle, or keep it out of service (i.e. vacation) for two weeks or more, run the air conditioning system at idle for about five minutes in the fresh air and high blower settings. This will insure adequate system lubrication to minimize the possibility of compressor damage when the system is started again. Side Window Demisters A side window demister outlet is located at each end of the instrument panel.
256 UNDERSTANDING YOUR INSTRUMENT PANEL A/C Air Filter — If Equipped The A/C Air Filter will reduce, but not eliminate, diesel and agricultural smells. The filter acts on air coming from outside the vehicle and recirculated air within the passenger compartment. Refer to “Maintenance Procedures” in Section 7 of this manual for A/C Air Filter service information or see your authorized dealer for service. Refer to the “Maintenance Schedules” in Section 8 of this manual for filter service intervals.
UNDERSTANDING YOUR INSTRUMENT PANEL 257 Control Setting Suggestions for Various Weather Conditions 4
258 UNDERSTANDING YOUR INSTRUMENT PANEL REAR WINDOW FEATURES Electric Rear Window Defroster — If Equipped The electric Rear Window Defroster Control is located on the climate control. Press this button to turn on the rear window defroster and the heated side mirrors (if equipped). An LED in the button will illuminate when the rear window defroster is ON.
STARTING AND OPERATING CONTENTS 䡵 Starting Procedures . . . . . . . . . . . . . . . . . . . . . 264 ▫ How To Use Remote Start . . . . . . . . . . . . . . . 268 ▫ Automatic Transaxle . . . . . . . . . . . . . . . . . . . 264 䡵 Engine Block Heater — If Equipped . . . . . . . . . 269 ▫ Normal Starting . . . . . . . . . . . . . . . . . . . . . . 265 䡵 Automatic Transaxle . . . . . . . . . . . . . . . . . . . . . 270 ▫ Tip Start Feature — Automatic Transaxle Only . . . . . . . . . . . . . . . . . . . . . .
260 STARTING AND OPERATING ▫ AutoStick威 General Information . . . . . . . . . . . 277 䡵 Driving On Slippery Surfaces . . . . . . . . . . . . . . 291 䡵 Parking Brake . . . . . . . . . . . . . . . . . . . . . . . . . 277 ▫ Acceleration . . . . . . . . . . . . . . . . . . . . . . . . . 291 䡵 Brake System . . . . . . . . . . . . . . . . . . . . . . . . . . 281 ▫ Traction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 292 ▫ Anti—Lock Brake System (ABS) . . . . . . . . . . .
STARTING AND OPERATING ▫ Tire Inflation Pressures . . . . . . . . . . . . . . . . . 304 ▫ Radial-Ply Tires . . . . . . . . . . . . . . . . . . . . . . 306 ▫ Compact Spare Tire — If Equipped . . . . . . . . . 307 ▫ Limited Use Spare — If Equipped . . . . . . . . . 307 ▫ Tire Spinning . . . . . . . . . . . . . . . . . . . . . . . . 308 ▫ Tread Wear Indicators . . . . . . . . . . . . . . . . . . 309 ▫ Life Of Tire . . . . . . . . . . . . . . . . . . . . . . . . . 309 ▫ Replacement Tires . . . . . . . . . . .
262 STARTING AND OPERATING ▫ Fuel System Cautions . . . . . . . . . . . . . . . . . . 326 䡵 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . 332 ▫ Carbon Monoxide Warnings . . . . . . . . . . . . . . 327 ▫ Fuel Filler Cap (Gas Cap) . . . . . . . . . . . . . . . 332 䡵 Flexible Fuel— 2.7L Engines Only (Except California Emission States) . . . . . . . . . . 328 ▫ Loose Fuel Filler Cap Message . . . . . . . . . . . . 334 ▫ E-85 General Information . . . . . . . . . . . . . . . .
STARTING AND OPERATING 263 ▫ Trailer Towing Weights (Maximum Trailer Weight Ratings) . . . . . . . . . 341 䡵 Recreational Towing (Behind Motorhome, Etc.) . . . . . . . . . . . . . . . . . 349 ▫ Trailer And Tongue Weight . . . . . . . . . . . . . . 342 ▫ Towing This Vehicle Behind Another Vehicle (Flat Towing With All Four Wheels On The Ground) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 349 ▫ Towing Requirements . . . . . . . . . . . . . . . . . . 343 ▫ Towing Tips . . . . . . . . . . . .
264 STARTING AND OPERATING STARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belt. Make sure all occupants have securely fastened their seat belts. WARNING! Never leave children alone in a vehicle. Leaving children in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Don’t leave the keys in the ignition.
STARTING AND OPERATING Normal Starting Normal Starting of either a cold or a warm engine does not require pumping or depressing the accelerator pedal. Simply turn the ignition switch to the “START” position and release when the engine starts. If the engine fails to start within 15 seconds, turn the ignition switch to the “LOCK” position, wait 10 to 15 seconds, then repeat the normal starting procedure. 265 WARNING! Do not attempt to push or tow your vehicle to get it started.
266 STARTING AND OPERATING Tip Start Feature — Automatic Transaxle Only Do not press the accelerator. Turn the ignition key briefly to START position, and release it. The starter motor will continue to run, but will automatically disengage itself when the engine is running. Ignition Key Position Extremely Cold Weather (below ⫺20°F or ⫺29°C) To insure reliable starting at these temperatures, use of an externally powered electric engine block heater (available from your dealer) is recommended.
STARTING AND OPERATING WARNING! Never pour fuel or other flammable liquid into the throttle body air inlet opening in an attempt to start the vehicle. This could result in flash fire causing serious personal injury. CAUTION! To prevent damage to the starter, do not crank the engine for more than 15 seconds at a time. Wait 10 to 15 seconds before trying again. 267 After Starting The idle speed will automatically decrease as the engine warms up.
268 STARTING AND OPERATING How To Use Remote Start To enter the Remote Start mode , depress the Remote Start button twice on the key fob. The engine will start and the vehicle will remain in the remote start mode for a 15 minute cycle. To exit the Remote Start mode , allow the engine to run the cycle or depress the unlock button to disarm the Vehicle Theft Security Alarm and within one minute insert the key into the ignition and turn the ignition to the RUN position.
STARTING AND OPERATING NOTE: When the vehicle is in the Remote Start mode, power window and sunroof operation are disabled for security.
270 STARTING AND OPERATING AUTOMATIC TRANSAXLE CAUTION! Damage to the transaxle may occur if the following precautions are not observed: • Shift the gear selector lever into PARK only after the vehicle has come to a complete stop. • Shift the gear selector lever into or out of REVERSE only after the vehicle has come to a complete stop and the engine is at idle speed.
STARTING AND OPERATING 271 WARNING! WARNING! It is dangerous to shift the gear selector lever out of PARK or NEUTRAL if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in REVERSE. You could lose control of the vehicle and hit someone or something. Only shift the gear selector lever into gear when the engine is idling normally and when your right foot is firmly on the brake pedal.
272 STARTING AND OPERATING BRAKE/TRANSAXLE INTERLOCK This system prevents you from moving the gear selector lever out of PARK and into any gear unless the brake pedal is pressed. This system is active only while the ignition switch is in the ON position. Always press the brake pedal first, before moving the gear selector lever out of PARK. NOTE: If a malfunction occurs, the transaxle will not shift out of PARK. Battery power is required to release the brake/transaxle interlock system.
STARTING AND OPERATING NOTE: If a malfunction occurs, the system will trap the key in the ignition cylinder to warn you that this safety feature is inoperable. The engine can be started and stopped, but the key cannot be removed until you obtain service. ELECTRONICALLY CONTROLLED AUTOMATIC TRANSAXLE The electronically controlled transaxle provides a precise shift schedule. The transaxle electronics are selfcalibrating; therefore, the first few shifts on a new vehicle may be somewhat abrupt.
274 STARTING AND OPERATING CAUTION! WARNING! DO NOT race the engine when shifting from PARK or NEUTRAL positions into another gear range as this can damage the drivetrain. Do not coast in NEUTRAL and never turn off the ignition to coast down a hill. These are unsafe practices that limit your response to changing traffic or road conditions. You might lose control of the vehicle and have an accident. REVERSE Use this range for moving the vehicle rearward.
STARTING AND OPERATING these conditions, using the [5] range will improve performance and extend transaxle life by reducing excessive shifting and heat build-up. RESET MODE — Electronic Transaxle The transaxle is monitored electronically for abnormal conditions. If a condition is detected that could cause damage, the transaxle automatically shifts into second gear. The transaxle remains in second gear (third gear with a six-speed automatic) despite the forward gear selected.
276 STARTING AND OPERATING driving, cold slippery conditions, mountain driving, trailer towing, and many other situations. AUTOSTICK姞 OPERATION By placing the gear selector lever one shift-level below the DRIVE position, it can be moved from side to side. This allows the driver to select a higher or lower range of gears. Moving the gear selector lever to the Left (-) triggers a downshift and to the Right (+) an upshift.
STARTING AND OPERATING AutoStick姞 General Information • You can start out in first or second gear. The system will ignore attempts to upshift at too low of a vehicle speed. • If a ratio other than 1st is selected, and the vehicle is brought to a stop, the transaxle control logic will automatically select the 1st gear ratio. • Starting out in second gear is helpful in snowy or icy conditions. • Avoid using speed control when Autostick威 is engaged.
278 STARTING AND OPERATING NOTE: If the light remains on with the parking brake released, a brake system malfunction is indicated. Have the brake system serviced by an authorized dealer immediately. Operation with an Automatic Transaxle When parking on a flat surface, place the gear selector lever in the PARK position first, and then apply the parking brake. NOTE: If the parking brake is applied while the vehicle is moving, a chime will sound to alert the driver.
STARTING AND OPERATING 279 Applying the Parking Brake To apply the parking brake, grasp the handle and pull it upward until you feel resistance. To release the parking brake, grasp the handle and pull it slightly while pressing the button on the end of the handle. When the button drops into the handle (releasing the lock), guide the handle downward to its stop and then release the button and the handle. 5 Parking Brake Lever NOTE: You should always apply the parking brake before leaving the vehicle.
280 STARTING AND OPERATING WARNING! WARNING! Never use PARK position on an automatic transaxle as a substitute for the parking brake. Always apply parking brake fully when parked to guard against vehicle movement and possible injury or damage. • Never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be injured. Don’t leave the keys in the ignition.
STARTING AND OPERATING BRAKE SYSTEM Your vehicle is equipped with power assisted brakes as standard equipment. In the event power assist is lost for any reason (i.e. repeated brake applications with the engine off) the brakes will still function. However, the effort required to brake the vehicle will be much greater than that required with the power system operating. 281 This light monitors various brake functions, including brake fluid level and parking brake application.
282 STARTING AND OPERATING WARNING! Driving a vehicle with the brake light on is dangerous. A significant decrease in braking performance or vehicle stability during braking may occur. It will take you longer to stop the vehicle or will make your vehicle harder to control. You could have an accident. Have the vehicle checked immediately. ANTI—LOCK BRAKE SYSTEM (ABS) The Anti-Lock Brake System provides increased vehicle stability and brake performance under most braking conditions.
STARTING AND OPERATING WARNING! • Anti-lock system (ABS) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded. • The ABS cannot prevent accidents, including those resulting from excessive speed in turns, following another vehicle too closely, or hydroplaning. Only a safe, attentive, and skillful driver can prevent accidents.
284 STARTING AND OPERATING When the vehicle is driven over 7 mph (11 km/h), you may also hear a slight clicking sound as well as some related motor noises. These noises are the system performing its self-check cycle to ensure that the ABS system is working properly. This self check occurs each time the vehicle is started and accelerated past 7 mph (11 km/h). • and a slight drop or fall away of the brake pedal at the end of the stop.
STARTING AND OPERATING ELECTRONIC BRAKE CONTROL SYSTEM – ABS/TCS/BAS/ESP Your vehicle may be equipped with an optional advanced electronic brake control system that includes Anti-Lock Brake System (ABS), Traction Control System (TCS), Brake Assist System (BAS), and Electronic Stability Program (ESP). All systems work together to enhance vehicle stability and control in various driving conditions and are commonly referred to as ESP.
286 STARTING AND OPERATING Brake Assist System (BAS) — If Equipped The BAS is designed to optimize the vehicle’s braking capability during emergency braking maneuvers. The system detects an emergency braking situation by sensing the rate and amount of brake application and then applies optimum pressure to the brakes. This can help reduce braking distances. The BAS complements the Anti-Lock Brake System (ABS). Applying the brakes very quickly results in the best BAS assistance.
STARTING AND OPERATING Electronic Stability Program (ESP) This system enhances directional control and stability of the vehicle under various driving conditions. ESP corrects for over/under steering of the vehicle by applying the brake of the appropriate wheel to assist in counteracting the over/under steer condition. Engine power may also be reduced to help the vehicle maintain the desired path.
288 STARTING AND OPERATING WARNING! • Electronic Stability Program (ESP) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. • ESP cannot prevent accidents, including those resulting from excessive speed in turns, driving on very slippery surfaces, or hydroplaning. Only a safe, attentive, and skillful driver can prevent accidents.
STARTING AND OPERATING or gravel conditions and more wheel spin than ESP would normally allow is required to gain traction. To turn ESP on again, momentarily depress the “ESP Control Switch.” This will restore the normal “ESP On” mode of operation. WARNING! In the Partial ESP mode, the engine torque reduction and stability features are desensitized. Therefore, the enhanced vehicle stability offered by ESP is unavailable.
290 STARTING AND OPERATING NOTE: • The “ESP Indicator Light” and the “ESP/BAS Warning Light” come on momentarily each time the ignition switch is turned ON. • Each time the ignition is turned ON, the ESP System will be ON even if it was turned off previously. • The ESP Control System will make buzzing or clicking sounds when it is active. This is normal; the sounds will stop when ESP becomes inactive following the maneuver that caused the ESP activation.
STARTING AND OPERATING WARNING! Continued operation with reduced power steering assist could pose a safety risk to yourself and others. Service should be obtained as soon as possible. CAUTION! Prolonged operation of the steering system at the end of the steering wheel travel will increase the steering fluid temperature and it should be avoided when possible. Damage to the power steering pump may occur.
292 STARTING AND OPERATING Traction When driving on wet or slushy roads, it is possible for a wedge of water to build up between the tire and road surface. This is hydroplaning and may cause partial or complete loss of vehicle control and stopping ability. To reduce this possibility, the following precautions should be observed: 1. Slow down during rainstorms or when roads are slushy. 2. Slow down if the road has standing water or puddles. 3.
STARTING AND OPERATING Shallow Standing Water Although your vehicle is capable of driving through shallow standing water, consider the following Caution and Warning before doing so. CAUTION! • Always check the depth of the standing water before driving through it. Never drive through standing water that is deeper than the bottom of the tire rims mounted on the vehicle.
294 STARTING AND OPERATING WARNING! • Driving through standing water limits your vehicle’s traction capabilities. Do not exceed 5 mph (8 km/h) when driving through standing water. TIRE SAFETY INFORMATION Tire Markings • Driving through standing water limits your vehicle’s braking capabilities, which increases stopping distances. Therefore, after driving through standing water, drive slowly and lightly press on the brake pedal several times to dry the brakes.
STARTING AND OPERATING 295 • European Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter ⬙P⬙ is absent from this tire size designation. Example: 215/65R15 96H • Temporary Spare tires are high pressure compact spares designed for temporary emergency use only. Tires designed to this standard have the letter “T” molded into the sidewall preceding the size designation.
296 STARTING AND OPERATING Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ⴖ....blank....ⴖ = Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary Spare tire 31 = Overall Diameter in Inches (in) 215 = Section Width in Millimeters (mm) 65 = Aspect Ratio in Percent (%) —Ratio of section height to section width of tire. 10.
STARTING AND OPERATING 297 EXAMPLE: Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry. H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions. —The maximum speed corresponding to the Speed Symbol should only be achieved under specified operating conditions. (i.e. tire pressure, vehicle loading, road conditions and posted speed limits).
298 STARTING AND OPERATING Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire however the date code may only be on one side. Tires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire. Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the outboard side then you will find it on the inboard side of the tire.
STARTING AND OPERATING Tire Loading and Tire Pressure 299 Tire and Loading Information Placard Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on either the face of the driver’s door or the driver’s side “B” pillar.
300 STARTING AND OPERATING 4) the cold tire inflation pressures for the front, rear and spare tires. Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the “Tire and Loading Information” placard and in the “Vehicle Loading” section of this manual.
STARTING AND OPERATING passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs. (since 5 x 150 = 750, and 1400 – 750 = 650 lbs.) 5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4. 6. If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle.
302 STARTING AND OPERATING
STARTING AND OPERATING WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES—GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle. Three primary areas are affected by improper tire pressure: 303 1.
304 STARTING AND OPERATING 2. Economy— Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Underinflation also increases tire rolling resistance and results in higher fuel consumption. 3. Ride Comfort and Vehicle Stability— Proper tire inflation contributes to a comfortable ride. Overinflation produces a jarring and uncomfortable ride.
STARTING AND OPERATING CAUTION! After inspecting or adjusting the tire pressure, always reinstall the valve stem cap–if equipped. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressures specified on the placard are always “cold tire inflation pressure”. Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or driven less than 1 mile (1 km) after a 3 hour period.
306 STARTING AND OPERATING loading may be required for high speed vehicle operation. Refer to original equipment or an authorized tire dealer for recommended safe operating speeds, loading and cold tire inflation pressures. WARNING! High speed driving with your vehicle under maximum load is dangerous. The added strain on your tires could cause them to fail. You could have a serious accident. Don’t drive a vehicle loaded to the maximum capacity at continuous speeds above 75 mph (120 km/h).
STARTING AND OPERATING Compact Spare Tire — If Equipped The compact spare is for temporary emergency use with radial tires. It is engineered to be used on your style vehicle only. Since this tire has limited tread life, the original tire should be repaired (or replaced) and reinstalled at the first opportunity. WARNING! Temporary use spare tires are for emergency use only. With these tires, do not drive more than 50 mph (80 km/h). Temporary-use spare tires have limited tread life.
308 STARTING AND OPERATING original equipped tire on the front or rear axle of your vehicle, but it is not. Installation of this limited use spare tire affects vehicle handling. Since it is not the same tire, replace (or repair) the original tire and reinstall on the vehicle at the first opportunity. Tire Spinning When stuck in mud, sand, snow, or ice conditions, do not spin your vehicle’s wheels faster than 30 mph (48 km/h) or for longer than 30 seconds continuously without stopping when you are stuck.
STARTING AND OPERATING Tread Wear Indicators Tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced. 309 These indicators are molded into the bottom of the tread grooves and will appear as bands when the tread depth becomes 1/16 inch (2 mm). When the tread is worn to the tread wear indicators, the tire should be replaced. Many states have laws requiring tire replacement at this point.
310 STARTING AND OPERATING WARNING! Tires and spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure. You could lose control and have an accident resulting in serious injury or death. Keep unmounted tires in a cool, dry place with as little exposure to light as possible. Protect tires from contact with oil, grease and gasoline.
STARTING AND OPERATING 311 WARNING! WARNING! Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle. This can cause unpredictable handling and stress to steering and suspension components. You could lose control and have an accident resulting in serious injury or death.
312 STARTING AND OPERATING Alignment And Balance Poor suspension alignment may result in: • Fast tire wear. • Uneven tire wear, such as feathering and one-sided wear. • Vehicle pull to right or left. Tires may also cause the vehicle to pull to the left or right. Alignment will not correct this condition. See your dealer for proper diagnosis. Improper alignment will not cause vehicle vibration. Vibration may be a result of tire and wheel out-ofbalance.
STARTING AND OPERATING 313 While studded tires improve performance on ice, skid and traction capability on wet or dry surfaces may be poorer than that of non-studded tires. Some states prohibit studded tires; therefore, local laws should be checked before using these tire types. Follow the Maintenance Schedule in Section 8 for the recommended tire rotation frequency. Remember, more frequent rotation is permissible if desired.
314 STARTING AND OPERATING TIRE PRESSURE MONITOR SYSTEM (TPMS) — IF EQUIPPED • The Tire Pressure Monitor System (TPMS) will warn the driver of a low tire pressure based on the vehicle recommended cold placard pressure. • The tire pressure will vary with temperature by about 1 psi (7 kPa) for every 12°F (7°C). This means that when the outside temperature decreases, the tire pressure will decrease. Tire pressure should always be set based on cold inflation tire pressure.
STARTING AND OPERATING once the system receives the updated tire pressures. The vehicle may need to be driven for up to 10 minutes above 15 mph (25 km/h) in order for the TPMS to receive this information. − For example, your vehicle may have a recommended cold (parked for more than 3 hours) placard pressure of 30 psi (207 kPa).
316 STARTING AND OPERATING NOTE: • The TPMS is not intended to replace normal tire care and maintenance, or to provide warning of a tire failure or condition. • The TPMS should not be used as a tire pressure gauge while adjusting your tire pressure. • Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability.
STARTING AND OPERATING 317 Tire Pressure Monitoring Low Pressure Warnings The Tire Pressure Monitoring Telltale Light will illuminate in the instrument cluster and a chime will sound when tire pressure is low in one or more of the four active road tires. Should this occur, you should stop as soon as possible, check the inflation pressure of each tire on your vehicle, and inflate each tire to the vehicle’s recommended cold placard pressure value.
318 STARTING AND OPERATING NOTE: 1. The compact spare tire (if so equipped) does not have a tire pressure monitoring sensor. Therefore, the TPMS will not monitor the pressure in the compact spare tire. 2. If you install the compact spare tire in place of a road tire that has a pressure below the low-pressure warning limit, upon the next ignition key cycle, a chime will sound and the TPM Telltale Light will turn ON. 3.
STARTING AND OPERATING 319 • 3 Trigger Modules (mounted in three of the four wheel-wells) • Various Tire Pressure Monitoring System Messages, which display in the Electronic Vehicle Information Center (EVIC) • Tire Pressure Monitoring Telltale Light Tire Pressure Monitoring Low Pressure Warnings The Tire Pressure Monitoring Telltale Light will illuminate in the instrument cluster and a chime will sound when tire pressure is low in one or more of the four active road tires.
320 STARTING AND OPERATING Should this occur, you should stop as soon as possible, and inflate the tires with low pressure (those flashing in the EVIC graphic) to the vehicle’s recommended cold placard pressure value. Once the system receives the updated tire pressures, the system will automatically update, the graphic display in the EVIC will stop flashing, and the Tire Pressure Monitoring Telltale Light will turn off.
STARTING AND OPERATING If the ignition key is cycled, this sequence will repeat, providing the system fault still exists. If the system fault no longer exists, the Tire Pressure Monitoring Telltale Light will no longer flash, and the ⬙CHECK TPM SYSTEM⬙ message will no longer display, and a pressure value will display in place of the dashes. A system fault can occur due to any of the following: 1.
322 STARTING AND OPERATING 4. For each subsequent ignition key cycle, a chime will sound, the TPM Telltale Light will flash on and off for 75 seconds and then remain on solid, and the EVIC will display a ⬙CHECK TPM SYSTEM⬙ message for 3 seconds and then display dashes (- -) in place of the pressure value. 5. Once you repair or replace the original road tire, and reinstall it on the vehicle in place of the compact spare, the TPMS will update automatically.
STARTING AND OPERATING FUEL REQUIREMENTS 2.4L and 2.7L Engines 2.4L and 2.7L engines are designed to meet all emission regulations and provide excellent fuel economy and performance when using high quality unleaded “regular” gasolines having an octane rating of 87. The use of premium gasoline is not recommended. Under normal conditions, the use of premium gasoline will not provide a benefit over high quality unleaded “regular” gasolines, and in some circumstances may result in poorer performance. 323 3.
324 STARTING AND OPERATING Poor quality gasoline can cause problems such as hard starting, stalling, and hesitations. If you experience these symptoms, try another brand of gasoline (with the appropriate octane rating for your engine) before considering service for the vehicle.
STARTING AND OPERATING CAUTION! For vehicles equipped with a 2.4L or 3.5L engine, DO NOT use gasoline containing Methanol or E85 Ethanol. Use of these blends may result in starting and driveability problems and may damage critical fuel system components. NOTE: The 2.7L engine is now rated for E85 Ethanol use (EXCEPT CALIFORNIA EMISSION STATES). Only vehicles with the E-85 fuel filler door label can operate on E-85. For more information, see “Flexible Fuel” in this section.
326 STARTING AND OPERATING Materials Added to Fuel All gasoline sold in the United States is required to contain effective detergent additives. Use of additional detergents or other additives is not needed under normal conditions and they would result in additional cost. Therefore, you should not have to add anything to the fuel. Fuel System Cautions CAUTION! Follow these guidelines to maintain your vehicle’s performance: • The use of leaded gas is prohibited by Federal law.
STARTING AND OPERATING Carbon Monoxide Warnings WARNING! Carbon monoxide (CO) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • Do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas, which can kill. Never run the engine in a closed area, such as a garage, and never sit in a parked vehicle with the engine running for an extended period.
328 STARTING AND OPERATING FLEXIBLE FUEL— 2.7L ENGINES ONLY (EXCEPT CALIFORNIA EMISSION STATES) E-85 General Information The information in this section is for Flexible Fuel vehicles only. This section only covers those subjects that are unique to these vehicles. Please refer to the other sections of this manual for information on features that are common between Flexible Fuel and gasoline only powered vehicles.
STARTING AND OPERATING Along with the special E-85 fuel filler cap, your vehicle may display a badge, which also indicates it can operate on E-85. 329 ETHANOL FUEL (E-85) E-85 is a mixture of approximately 85% fuel ethanol and 15% unleaded gasoline. WARNING! Ethanol vapors are extremely flammable and could cause serious personal injury. Never have any smoking materials lit in or near the vehicle when removing the fuel filler tube cap (gas cap) or filling the tank.
330 STARTING AND OPERATING For best results, a refueling pattern that alternates between E-85 and unleaded gasoline should be avoided.
STARTING AND OPERATING Starting The characteristics of E-85 fuel make it unsuitable for use when ambient temperatures fall below 0° F (-18° C). In the range of 0° F (-18° C) to 32° F (0° C), you may experience an increase in the time it takes for your engine to start, and a deterioration in drivability (sags and/or hesitations) until the engine is fully warmed up. Cruising Range Because E-85 fuel contains less energy per gallon than gasoline, you will experience an increase in fuel consumption.
332 STARTING AND OPERATING ADDING FUEL Fuel Filler Cap (Gas Cap) As a reminder, a fuel icon with an arrow indicating which side of the vehicle the fuel filler door is located on, is located in the instrument cluster, just below the Fuel Gage. The gas cap is behind the fuel filler door, on the left rear quarter panel of the vehicle. If the gas cap is lost or damaged, be sure the replacement cap is for use with this vehicle.
STARTING AND OPERATING After removing the gas cap, place the gas cap tether cable over a hook on the inside of the fuel door. This keeps the gas cap suspended away from and protects the vehicle’s surface. 333 CAUTION! • Damage to the fuel system or emission control system could result from using an improper fuel tank filler tube cap (gas cap). • A poorly fitting gas cap could let impurities into the fuel system. • A poorly fitting gas cap may cause the Malfunction Indicator Light to turn on.
334 STARTING AND OPERATING WARNING! • Never have any smoking materials lit in or near the vehicle when the gas cap is removed or the tank filled. • Never add fuel when the engine is running. This is in violation of most state and federal fire regulations and doing so will cause the malfunction indicator light to turn on. • A fire may result if gasoline is pumped into a portable container that is inside of a vehicle. You could be burned. Always place gas containers on the ground while filling.
STARTING AND OPERATING VEHICLE LOADING Vehicle Loading Capacities Front Seat Occupants . . . . . . . . . . . . . . . . . . . . . . . 2 Rear Seat Occupants . . . . . . . . . . . . . . . . . . . . . . . 3 Luggage. . . . . . . . . . . . . . . . . 13.0 cu. ft. (0.368 cu. M) The load carrying capacity of your vehicle is shown on the “Vehicle Certification Label.” This information should be used for passenger and luggage loading as indicated. Vehicle Curb Weight 2.4 L Base. . . . . . . . 2.7 L Base. . . . . . .
336 STARTING AND OPERATING Gross Vehicle Weight Rating (GVWR) The GVWR is the total allowable weight of your vehicle. This includes driver, passengers, and cargo. The total load must be limited so that you do not exceed the GVWR. Overloading The load carrying components (axle, springs, tires, wheels, etc.) of your vehicle will provide satisfactory service as long as you do not exceed the GVWR and front and rear GAWR.
STARTING AND OPERATING Loading To load your vehicle properly, first figure out its empty weight, axle by axle and side by side. Store heavier items down low and be sure you distribute their weight as evenly as possible. Stow all loose items securely before driving. If weighing the loaded vehicle shows that you have exceeded either GAWR, but the total load is within the specified GVWR, you must redistribute the weight.
338 STARTING AND OPERATING TRAILER TOWING In this section, you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle. Before towing a trailer, carefully review this information to tow your load as efficiently and safely as possible. To maintain warranty coverage, follow the requirements and recommendations in this manual concerning vehicles used for trailer towing.
STARTING AND OPERATING Gross Combination Weight Rating (GCWR) The gross combination weight rating (GCWR) is the total permissible weight of your vehicle and trailer when weighed in combination. (Note that GCWR ratings include a 150 lbs (68 kg) allowance for the presence of a driver). Gross Axle Weight Rating (GAWR) The GAWR is the maximum capacity of the front and rear axles. Distribute the load over the front and rear axles evenly. Make sure that you do not exceed either front or rear GAWR.
340 STARTING AND OPERATING Frontal Area Frontal Area is the maximum height and maximum width of the front of a trailer and its cargo. Weight-Carrying Hitch A weight-carrying hitch supports the trailer tongue weight, just as if it were luggage located at a hitch ball or some other connecting point of the truck. These kinds of hitches are the most popular on the market today and they’re commonly used to tow small- and medium-sized trailers.
STARTING AND OPERATING 341 Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/Transaxle 2.4L/Auto 2.7L/Auto 3.5L/Auto Max. Frontal Area Max. GTW (Gross Trailer Wt.) 2 See Note 1000 lbs (450 kg) See Note 2 1500 lbs (680 kg) 22 Sq., Ft. (2.0 Sq. M) 2000 lbs (900 kg) Refer to local laws for maximum trailer towing speeds.
342 STARTING AND OPERATING Trailer and Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% of the Gross Trailer Weight (GTW) on the tow hitch of your vehicle. Loads balanced over the wheels or heavier in the rear can cause the trailer to sway severely side to side which will cause loss of control of vehicle and trailer. Failure to load trailers heavier in front is the cause of many trailer accidents.
STARTING AND OPERATING NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options, or dealer-installed options, must be considered as part of the total load on your vehicle. Refer to the Tire and Loading Information placard in the Tire Safety Information Section of this manual for the maximum combined weight of occupants and cargo for your vehicle.
344 STARTING AND OPERATING WARNING! Improper towing can lead to an injury accident. Follow these guidelines to make your trailer towing as safe as possible: Make certain that the load is secured in the trailer and that it will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control. You could lose control of your vehicle and have an accident.
STARTING AND OPERATING 4. Tongue weight rating for the trailer hitch utilized (This requirement may limit the ability to always achieve 10% of tongue weight as a percentage of total trailer weight). Towing Requirements — Tires • Do not attempt to tow a trailer while using a compact spare tire. 345 Information” in this section for information on tread wear indicators and for proper inspection procedure.
346 STARTING AND OPERATING • Trailer brakes are recommended for trailers over 1,000 lbs (450 kg) and required for trailers in excess of 2,000 lbs (907 kg). CAUTION! If the trailer weighs more than 1,000 lbs (450 kg) loaded, it should have its own brakes, and they should be of adequate capacity. Failure to do this could lead to accelerated brake lining wear, higher brake pedal effort, and longer stopping distances. WARNING! Do not connect trailer brakes to your vehicle’s hydraulic brake lines.
STARTING AND OPERATING 347 NOTE: Do not cut or splice wiring into the vehicles wiring harness. The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. 5 7-Pin Connector 4-Pin Connector Towing Tips Before setting out on a trip, practice turning, stopping, and backing the trailer in an area located away from heavy traffic. Make sure all trailer and vehicle lights are working properly — including hazard flashers.
348 STARTING AND OPERATING Automatic Transaxle The DRIVE range can be selected when towing. However, if frequent shifting occurs while in this range, third gear for a four—speed automatic and the fifth gear for a six-speed AutoStick威 should be selected. NOTE: Check the four-speed automatic transaxle fluid level before towing. AutoStick威 six—speed transmission is sealed and the fluid level cannot be checked. See your authorized dealership service center for assistance.
STARTING AND OPERATING Cooling System To reduce potential for engine and transaxle overheating, take the following actions: • City Driving When stopped for short periods of time, put transaxle in neutral and increase engine idle speed. • Highway Driving Reduce speed. • Air Conditioning Turn off temporarily. • Refer to Cooling System Operating information in the Maintenance section of this manual for more information.
WHAT TO DO IN EMERGENCIES CONTENTS 䡵 Hazard Warning Flasher . . . . . . . . . . . . . . . . . . 353 ▫ Jacking Instructions . . . . . . . . . . . . . . . . . . . . 358 䡵 If Your Engine Overheats . . . . . . . . . . . . . . . . . 353 䡵 Jump-Starting Procedures Due To A Low Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 364 ▫ Engine Oil Overheating — 2.4L Engine Only (If Equipped) . . . . . . . . . . . . . . . . . . . . . . . . 355 䡵 Freeing A Stuck Vehicle . . . . . . . . . . . . . .
352 WHAT TO DO IN EMERGENCIES ▫ Towing This Vehicle Behind Another Vehicle With A Tow Dolly . . . . . . . . . . . . . . . . . . . . . 370 ▫ Without Power — Override Transaxle Interlock System . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER The flasher switch is located on the instrument panel, below the radio. Depress the switch and both cluster indicators and all front and rear directional signals will flash. Depress the switch again to turn Hazard Warning Flashers off. 353 Do not use this emergency warning system when the vehicle is in motion. Use it when your vehicle is disabled and it is creating a safety hazard for other motorists.
354 WHAT TO DO IN EMERGENCIES If the pointer rises to the H (red) mark, the instrument cluster will sound a chime. Pull over and stop the vehicle with the engine at idle, when safe. Turn off the air conditioning and wait until the pointer drops back into the normal range. If the pointer remains on the H (red) mark for more than a minute, turn the engine off immediately and call for service. NOTE: There are steps that you can take to slow down an impending overheat condition.
WHAT TO DO IN EMERGENCIES WARNING! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call a service center if your vehicle overheats. If you decide to look under the hood yourself, refer to Section 7, Maintenance, of this manual. Follow the warnings under the Cooling System Pressure Cap paragraph. 355 Engine Oil Overheating — 2.
356 WHAT TO DO IN EMERGENCIES JACKING AND TIRE CHANGING WARNING! • Being under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never put any part of your body under a vehicle that is on a jack. Never start or run the engine while the vehicle is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift. • The jack is designed to use as a tool for changing tires only.
WHAT TO DO IN EMERGENCIES 357 WARNING! Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. • Turn on the Hazard Warning Flasher. Spare Tire and Jack Stowage Preparations For Jacking Park the vehicle on a firm level surface, avoid ice or slippery areas, set the parking brake and place the gear selector in PARK (automatic transaxle) or REVERSE (manual transaxle).
358 WHAT TO DO IN EMERGENCIES Jacking Instructions WARNING! Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: Jack Warning Label • Always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle. • Block the wheel diagonally opposite the wheel to be raised. • Set the parking brake firmly and set an automatic transmission in park; a manual transmission in reverse.
WHAT TO DO IN EMERGENCIES 359 WARNING! WARNING! Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: • Never start or run the engine with the vehicle on a jack. • If working on or near a roadway, be extremely careful of motor traffic. • Do not let anyone sit in the vehicle when it is on a jack.
360 WHAT TO DO IN EMERGENCIES 1. Remove the scissors jack and lug wrench from the spare wheel as an assembly. Turn the jack screw to the left to loosen the lug wrench, and remove the wrench from the jack assembly. NOTE: The Jack Handle attaches to the side of the jack with two attachment points. When the jack is partially expanded, the tension between the two attachment points holds the jack handle in place. Removing Jack Handle From Jack 2.
WHAT TO DO IN EMERGENCIES 361 6 Jacking Locations
362 WHAT TO DO IN EMERGENCIES CAUTION! WARNING! Do not attempt to raise the vehicle by jacking on locations other than those indicated in step 3. Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 3. There are two front jacking locations and two rear jacking locations on each side of the body (as pictured above). 4.
WHAT TO DO IN EMERGENCIES 363 WARNING! WARNING! To avoid possible personal injury, handle the wheel covers with care to avoid contact with any sharp edges. A loose tire or jack thrown forward in a collision or hard stop could endanger the occupants of the vehicle. Always stow the jack parts and the spare tire in the places provided. Have the deflated (flat) tire repaired or replaced immediately. 7. Lower the vehicle by turning the jack screw to the left. 8. Finish tightening the nuts.
364 WHAT TO DO IN EMERGENCIES JUMP-STARTING PROCEDURES DUE TO A LOW BATTERY Jump-starting remote battery terminals are located under the hood. The battery is stored between the left front headlight assembly and the left front wheel splash shield. Access is through the splash shield. WARNING! • Take care to avoid the radiator cooling fan whenever the hood is raised. It can start anytime the ignition switch is on. You can be hurt by the fan. • Do not attempt to push or tow your vehicle to get it started.
WHAT TO DO IN EMERGENCIES 1. Wear eye protection and remove any metal jewelry such as watchbands or bracelets that might make an inadvertent electrical contact. 2. When boosting from a battery in another vehicle, park that vehicle within booster cable reach, but without allowing the vehicles to touch. Set parking brake, place automatic transaxle in PARK and turn ignition to LOCK for both vehicles.
366 WHAT TO DO IN EMERGENCIES 7. Start the engine in the vehicle that has the booster battery, let the engine idle a few minutes, and then start the engine in the vehicle with the discharged battery. 8. When removing the jumper cables, reverse the sequence exactly. Be careful of the moving belts and fan. 9. Reinstall the protective cover over the remote jumpstart positive battery post. WARNING! Jump-Starting Location 6.
WHAT TO DO IN EMERGENCIES NOTE: Refer to “Maintenance Procedures” in Section 7 of this manual for information on accessing the battery for service or replacement. WARNING! Any procedure other than above could result in: 1. Personal injury caused by electrolyte squirting out the battery vent; 2. Personal injury or property damage due to battery explosion; 3. Damage to charging system of booster vehicle or of immobilized vehicle.
368 WHAT TO DO IN EMERGENCIES WARNING! Fast spinning tires can be dangerous. Forces generated by excessive wheel speeds may cause axle and tire damage or failure. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 30 mph (48 km/h) or for longer than 30 seconds continuously without stopping when you are stuck, and don’t let anyone near a spinning wheel, no matter what the speed.
WHAT TO DO IN EMERGENCIES CAUTION! • If the vehicle being towed requires steering, the ignition switch must be in the ON position, not in the LOCK or ACC position. • Do not attempt to tow this vehicle from the front with sling type towing equipment. Damage to the front fascia will result. • Do not push or tow this vehicle with another vehicle as damage to the bumper fascia and transaxle may result. If you must use the accessories (wipers, defrosters, etc.
370 WHAT TO DO IN EMERGENCIES TOWING THIS VEHICLE BEHIND ANOTHER VEHICLE WITH A TOW DOLLY Rear towing is not recommended with the front wheels on the ground, as transaxle damage can result. If rear towing is the only alternative, a front end dolly must be used. Proper towing equipment is necessary to prevent damage to the vehicle. • Firmly apply the parking brake.
MAINTAINING YOUR VEHICLE CONTENTS 䡵 2.4L Gas Engine Compartment . . . . . . . . . . . . . 374 䡵 Maintenance Procedures . . . . . . . . . . . . . . . . . . 380 䡵 2.7L Gas Engine Compartment . . . . . . . . . . . . . 375 ▫ Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . 380 䡵 3.5L Engine Compartment . . . . . . . . . . . . . . . . 376 ▫ Engine Oil Filter . . . . . . . . . . . . . . . . . . . . . . 384 䡵 Onboard Diagnostic System — OBD II . . . . . . . . 377 ▫ Drive Belt . . . . . . . . .
372 MAINTAINING YOUR VEHICLE ▫ A/C Air Filter — If Equipped . . . . . . . . . . . . 389 ▫ Front And Rear Wheel Bearings . . . . . . . . . . . 406 ▫ Power Steering — Fluid Check . . . . . . . . . . . . 391 ▫ Appearance Care And Protection From Corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . . 406 ▫ Front Suspension Ball Joints . . . . . . . . . . . . . . 391 ▫ Steering Linkage . . . . . . . . . . . . . . . . . . . . . . 392 ▫ Body Lubrication . . . . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE ▫ Tail/Stop Light, Rear Turn Signal Light, Backup Light . . . . . . . . . . . . . . . . . . . . . . . . 424 ▫ License Plate Light . . . . . . . . . . . . . . . . . . . . 427 ▫ Center High-Mounted Stop Light (CHMSL) . . . 428 373 䡵 Fluids And Capacities . . . . . . . . . . . . . . . . . . . 429 䡵 Fluids, Lubricants, And Genuine Parts . . . . . . . . 430 ▫ Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
374 MAINTAINING YOUR VEHICLE 2.
MAINTAINING YOUR VEHICLE 375 2.
376 MAINTAINING YOUR VEHICLE 3.5L ENGINE COMPARTMENT 3.
MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated Onboard Diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transaxle control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
378 MAINTAINING YOUR VEHICLE RESET button to turn off the message. If the problem persists, the message will appear the next time the vehicle is started. This might indicate a damaged cap. If the problem is detected twice in a row, the system will turn on the MIL. Resolving the problem will turn the MIL light off. EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle’s emissions control system.
MAINTAINING YOUR VEHICLE 379 5. Approximately 15 seconds later, one of two things will happen: system to update. A recheck with the above test routine may then indicate that the system is now ready. a. The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition key or start the engine. This means that your vehicle’s OBD II system is not ready and you should not proceed to the I/M station.
380 MAINTAINING YOUR VEHICLE AUTHORIZED DEALER SERVICE Your authorized dealer has the qualified service personnel, special tools, and equipment to perform all service operations in an expert manner. Service manuals are available which include detailed service information for your vehicle. Refer to these Service manuals before attempting any procedure yourself. NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you.
MAINTAINING YOUR VEHICLE 381 The best time to check the engine oil level is about 5 minutes after a fully warmed engine is shut off. Do not check oil level before starting the engine after it has sat overnight. Checking engine oil level when the engine is cold will give you an incorrect reading. Checking the oil while the vehicle is on level ground and only when the engine is hot, will improve the accuracy of the oil level readings. Maintain the oil level between the range markings on the dipstick.
382 MAINTAINING YOUR VEHICLE Do not overfill the engine. Overfilling the engine will cause oil aeration, which can lead to loss of oil pressure and an increase in oil temperature. This could damage your engine. Engine Oil Selection For best performance and maximum protection under all types of operating conditions, the manufacturer recommends engine oils that are API Certified and meet the requirements of DaimlerChrysler Material Standard MS6395.
MAINTAINING YOUR VEHICLE Engine Oil Viscosity (SAE Grade) — 2.4L and 2.7L Engines SAE 5W-20 engine oil is recommended for all operating temperatures. This engine oil improves low temperature starting and vehicle fuel economy. Your engine oil filler cap also shows the recommended engine oil viscosity for your vehicle. The engine oil filler cap also shows the recommended engine oil viscosity for your engine.
384 MAINTAINING YOUR VEHICLE Materials Added To Engine Oils The manufacture strongly recommends against the addition of any additives (other than leak detection dyes) to the engine oil. Engine oil is an engineered product and it’s performance may be impaired by supplemental additives. Disposing of Used Engine Oil and Oil Filters Care should be taken in disposing of used engine oil and oil filters from your vehicle.
MAINTAINING YOUR VEHICLE Spark Plugs Spark plugs must fire properly to assure engine performance and emission control. New plugs should be installed at the specified mileage. The entire set should be replaced if there is any malfunction due to a faulty spark plug. Refer to “Fluids, Lubricants, and Genuine Parts” in this section for the proper type of spark plug for use in your vehicle.
386 MAINTAINING YOUR VEHICLE Under normal operating conditions, the catalytic converter will not require maintenance. However, it is important to keep the engine properly tuned to assure proper catalyst operation and prevent possible catalyst damage. NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you. CAUTION! A hot exhaust system can start a fire if you park over materials that can burn.
MAINTAINING YOUR VEHICLE To minimize the possibility of catalyst damage: • Do not shut off the engine or interrupt the ignition when the transaxle is in gear and the vehicle is in motion. • Do not try to start the engine by pushing or towing the vehicle. • Do not idle the engine with any ignition coil connectors disconnected for prolonged periods. Maintenance-Free Battery You will never have to add water, nor is periodic maintenance required.
388 MAINTAINING YOUR VEHICLE CAUTION! • It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked positive (+) and negative (-) and identified on the battery case. Cable clamps should be tight on the terminal posts and free of corrosion. Apply grease to posts and clamps after tightening.
MAINTAINING YOUR VEHICLE WARNING! • Use only refrigerants and compressor lubricants approved by the manufacturer for your air conditioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs. Refer to Section 3 of the Warranty Information book for further warranty information. • The air conditioning system contains refrigerant under high pressure.
390 MAINTAINING YOUR VEHICLE The A/C Air Filter is located in the fresh air inlet behind the glove box. Perform the following procedure to replace the filter: 1. Open the glove box and remove all contents. 2. Push in on the sides of the glove box and lower the door. 3. Disconnect the glove box door dampener from the slot on the side of the box.
MAINTAINING YOUR VEHICLE 391 CAUTION! WARNING! The A/C Air Filter is labeled with an arrow to indicate airflow direction through the filter. Failure to install the filter properly will result in the need to replace it more often. Fluid level should be checked on a level surface and with the engine off to prevent injury from moving parts and to insure accurate fluid level reading. Do not overfill. Use only manufacturers recommended power steering fluid. 8.
392 MAINTAINING YOUR VEHICLE Steering Linkage The tie rod end ball joints should be inspected for external leakage and damage when other maintenance is performed. Body Lubrication Locks and all body pivot points, including seat tracks, door hinges, trunk hinges, and hood hinges, should be lubricated periodically to assure quiet, easy operation and to protect against rust and wear.
MAINTAINING YOUR VEHICLE 393 Keep the blade rubber out of contact with petroleum products such as engine oil, gasoline, etc. WARNING! NOTE: Always refer to the wiper blade packaging for specific installation instructions. Many wiper blade replacements fit multiple vehicles. Commercially available windshield washer solvents are flammable. They could ignite and burn you. Care must be exercised when filling or working around the washer solution.
394 MAINTAINING YOUR VEHICLE into the passenger compartment. In addition, inspect the exhaust system each time the vehicle is raised for an oil change or lubrication. Replace as required. WARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO) which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing CO, refer to Exhaust Gas in the Safety Tips section of this manual.
MAINTAINING YOUR VEHICLE Coolant Checks Check engine coolant (antifreeze) protection every 12 months (before the onset of freezing weather, where applicable). If coolant is dirty or rusty in appearance, the system should be drained, flushed, and refilled with fresh coolant. Check the front of the A/C condenser for any accumulation of bugs, leaves, etc. If dirty, clean by gently spraying water from a garden hose vertically down the face of the condenser.
396 MAINTAINING YOUR VEHICLE CAUTION! • Mixing of coolants other than specified HOAT engine coolants, may result in engine damage and may decrease corrosion protection. If a non-HOAT coolant is introduced into the cooling system in an emergency, it should be replaced with the specified coolant as soon as possible. • Do not use plain water alone or alcohol-base engine coolant (antifreeze) products.
MAINTAINING YOUR VEHICLE • Use only high purity water such as distilled or deionized water when mixing the water/engine coolant solution. The use of lower quality water will reduce the amount of corrosion protection in the engine cooling system. Please note that it is the owner’s responsibility to maintain the proper level of protection against freezing according to the temperatures occurring in the area where the vehicle is operated.
398 MAINTAINING YOUR VEHICLE Disposal of Used Engine Coolant Used ethylene glycol based engine coolant is a regulated substance requiring proper disposal. Check with your local authorities to determine the disposal rules for your community. To prevent ingestion by animals or children, do not store ethylene glycol based engine coolant in open containers or allow it to remain in puddles on the ground. If ingested by a child, contact a physician immediately. Clean up any ground spills immediately.
MAINTAINING YOUR VEHICLE humidity accumulating on the radiator and being vaporized when the thermostat opens, allowing hot coolant to enter the radiator. If an examination of your engine compartment shows no evidence of radiator or hose leaks, the vehicle may be safely driven. The vapor will soon dissipate. • Do not overfill the coolant recovery bottle. • Check coolant freeze point in the radiator and in the coolant recovery bottle.
400 MAINTAINING YOUR VEHICLE Hoses and Vacuum/Vapor Harnesses Inspect surfaces of hoses and nylon tubing for evidence of heat and mechanical damage. Hard or soft spots, brittle rubber, cracking, tears, cuts, abrasions, and excessive swelling indicate deterioration of the rubber Pay particular attention to the hoses nearest to high heat sources such as the exhaust manifold. Inspect hose routing to be sure hoses do not touch any heat source or moving component that may cause heat damage or mechanical wear.
MAINTAINING YOUR VEHICLE WARNING! Riding the brakes can lead to brake failure and possibly an accident. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage. You wouldn’t have your full braking capacity in an emergency. Brake And Power Steering Hoses When servicing the vehicle for scheduled maintenance, inspect the surface of the hoses and nylon tubing for evidence of heat and mechanical damage.
402 MAINTAINING YOUR VEHICLE WARNING! Worn brake hoses can burst and cause brake failure. You could have an accident. If you see any signs of cracking, scuffing, or worn spots, have the brake hoses replaced immediately. Master Cylinder - Brake Fluid Level Check Check the fluid level in the master cylinder immediately if the brake system warning light indicates system failure. Check the fluid level in the master cylinder when performing underhood services.
MAINTAINING YOUR VEHICLE 403 WARNING! CAUTION! • Overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts and the brake fluid catching fire. Do not allow petroleum base fluid to contaminate the brake fluid, all brake seal components could be damaged causing partial or complete brake failure.
404 MAINTAINING YOUR VEHICLE Fluid Level Check — Vehicles with 2.4L and 2.7L Engines Use the following procedure to check the automatic transaxle fluid level properly: 1. Park the vehicle on level ground. 2. Run the engine at curb idle speed for a minimum of 60 seconds. 3. Apply the parking brake fully. 4. Place the gear selector momentarily in each gear position ending with the lever in “P” (Park). 5. Wipe the area around the dipstick clean to eliminate the possibility of dirt entering the transaxle. 6.
MAINTAINING YOUR VEHICLE CAUTION! • Using a transmission fluid other than the manufacturer’s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder. Using a transmission fluid other than that recommended by the manufacturer will result in more frequent fluid and filter changes. Refer to “Fluids, Lubricants, and Genuine Parts” for the correct fluid type. • Dirt and water in the transaxle can cause serious damage.
406 MAINTAINING YOUR VEHICLE Front and Rear Wheel Bearings Front and rear wheel bearings are permanently sealed. No regular maintenance is required for these components. Appearance Care And Protection From Corrosion Protection Of Body And Paint from Corrosion Vehicle body care requirements vary according to geographic locations and usage.
MAINTAINING YOUR VEHICLE Washing • Wash your vehicle regularly. Always wash your vehicle in the shade using Mopar威 Car Wash or a mild car wash soap, and rinse the panels completely with clear water. • If insects, tar, or other similar deposits have accumulated on your vehicle, use Mopar威 Super Kleen Bug and Tar Remover to remove. • Use Mopar威 Cleaner Wax to remove road film, stains and to protect your paint finish. Take care never to scratch the paint.
408 MAINTAINING YOUR VEHICLE • If your vehicle is damaged due to an accident or similar cause, which destroys the paint and protective coating, have your vehicle repaired as soon as possible. The cost of such repairs is considered the responsibility of the owner. • If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials are well packaged and sealed. • If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel.
MAINTAINING YOUR VEHICLE Mopar威 Spot & Stain Remover if absolutely necessary. Do not use harsh cleaners or Armorall. Use Mopar威 Total Clean to clean vinyl upholstery Cleaning Leather Upholstery Mopar威 Total Clean is specifically recommended for leather upholstery. Your leather upholstery can be best preserved by regular cleaning with a damp soft cloth. Small particles of dirt can act as an abrasive and damage the leather upholstery and should be removed promptly with a damp cloth.
410 MAINTAINING YOUR VEHICLE • For grease stains, apply Mopar威 Multi-Purpose Cleaner to a clean, damp cloth and remove stain. Use a fresh, damp towel to remove soap residue. • Do not use any solvents or protectants on Yes Essentials威 products. Cleaning Headlights Your vehicle has plastic headlights that are lighter and less susceptible to stone breakage than glass headlights. Plastic is not as scratch resistant as glass and therefore different lens cleaning procedures must be followed.
MAINTAINING YOUR VEHICLE 1. Clean with a wet soft rag. A mild soap solution may be used, but do not use high alcohol content or abrasive cleaners. If soap is used, wipe clean with a clean damp rag. 2. Dry with a soft tissue. Seat Belt Maintenance Do not bleach, dye, or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage can also weaken the fabric. If the belts need cleaning, use a mild soap solution or lukewarm water.
412 MAINTAINING YOUR VEHICLE FUSES/TOTALLY INTEGRATED POWER MODULE (TIPM) A Totally Integrated Power Module is located in the engine compartment near the air cleaner assembly. This center contains cartridge fuses and mini fuses. A label that identifies each component may be printed on the inside of the cover. Refer to the graphic below for FUSES/TIPM location.
MAINTAINING YOUR VEHICLE Cavity Cartridge Mini Fuse Fuse 3 — 4 — 5 — 6 — 7 — 8 — 10 Amp Red 10 Amp Red 20 Amp Yellow 10 Amp Red 30 Amp Green 30 Amp Green Description Battery Feed — Center High Mounted Stop Light (CHMSL)/Brake Switch Battery Feed — Ignition Switch Trailer Tow — If Equipped Ignition Off Draw (IOD) — Power Mirror Switch/Climate Controls Ignition Off Draw (IOD) Sense 1 Ignition Off Draw (IOD) Sense 2 Cavity Cartridge Mini Fuse Fuse 9 40 Amp Green 10 — 11 — 12 — 13 —
414 MAINTAINING YOUR VEHICLE Cavity 14 Cartridge Mini Fuse Fuse — 10 Amp Red 15 40 Amp Green — 16 — 15 Amp Lt.
MAINTAINING YOUR VEHICLE Cavity 26 27 28 29 30 Cartridge Mini Fuse Description Fuse 15 Amp Auto Shutdown (ASD) — Lt.
416 MAINTAINING YOUR VEHICLE Cavity Cartridge Mini Fuse Fuse 35 40 Amp Green — 36 30 Amp Pink — 37 — 25 Amp Clear Description CAUTION! Battery Feed — AntiLock Brakes (ABS) Module - If Equipped/ Electronic Stability Program (ESP) Module - If Equipped Battery Feed — Passenger Door Module (PDM)/Driver Door Module (DDM) • When installing the Totally Integrated Power Module cover, it is important to ensure the cover is properly positioned and fully latched.
MAINTAINING YOUR VEHICLE VEHICLE STORAGE If you will not be using your vehicle for more than 21 days, you may want to take steps to preserve your battery. You may: • Disengage the mini-fuse in the Power Distribution Center labeled IOD (Ignition Off-Draw). • Or, disconnect the negative cable from the battery. REPLACEMENT BULBS All the inside bulbs are brass or glass wedge base. Aluminum base bulbs are not approved and should not be used for replacement.
418 MAINTAINING YOUR VEHICLE BULB REPLACEMENT Headlight Bulb Replacement 1. Raise and prop open the hood. Locate the connector behind the headlight. NOTE: It may be necessary to remove the air cleaner filter housing and position the totally integrated power module aside prior to replacing the low beam headlight on the driver’s side of the vehicle. 2. Reach into engine compartment and from behind the lamp assembly and grasp the connector.
MAINTAINING YOUR VEHICLE 1 — High Beam Headlight 2 — Low Beam Headlight 3. Rotate bulb and connector one-quarter turn and pull outward from assembly. 419 Twisting Bulb From Socket CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life.
420 MAINTAINING YOUR VEHICLE 4. Pull the bulb out of the socket and replace the bulb. Head Light Assembly Removal — Bulb Replacement 1. Raise and prop open the hood. Remove the headlight mounting screws. Removing Halogen Bulb From Assembly 5. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol. 6. Reinsert the bulb and socket assembly and rotate clockwise one-quarter turn to secure. Mounting Screw Location 2.
MAINTAINING YOUR VEHICLE 3. Gently pry the headlight assembly away from the fender as shown in the picture. This will free the ball stud from its retainer in the fender. Pull the headlight assembly away from the vehicle. 421 4. Follow Steps 3 — 6 in the above “Headlight Bulb Replacement” section. 5. Reinstall Head Light Assembly by reversing steps 2 and 3 above.
422 MAINTAINING YOUR VEHICLE Front Turn Signal/Park Light 1. Raise and prop open the hood. 2. Rotate the bulb’s electrical connector one-quarter turn counterclockwise and remove it from the headlight housing. 3. Remove the bulb from the connector socket and install the replacement bulb. 4. Install the bulb and connector assembly into the headlight housing and rotate the connector one-quarter turn clockwise to lock it in place.
MAINTAINING YOUR VEHICLE 1. Rotate the bulb’s electrical connector one-quarter turn counterclockwise and remove it from the fog light housing. 423 2. Remove the bulb from the connector socket and install the replacement bulb. CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with an oily surface, clean the bulb with rubbing alcohol. 3.
424 MAINTAINING YOUR VEHICLE Tail/Stop Light, Rear Turn Signal Light, Backup Light The taillights are a two piece design. The turn signal, brake and taillights are located in the rear corner body panel housing. The back up and taillights are located in the trunk lid housing. Changing the Tail/Stop Light or Rear Turn Signal Light 1.
MAINTAINING YOUR VEHICLE 2. Remove the two plastic wing nuts from the taillight housing. 425 4. Rotate the applicable bulb’s electrical connector onequarter turn counterclockwise and remove it from the taillight housing. 7 Location Plastic Wing Nuts 3. Grasp the taillight housing and pull it firmly outward while pushing gently on the studs from inside to disengage the housing from the vehicle.
426 MAINTAINING YOUR VEHICLE 5. Remove the bulb from the connector socket and install the replacement bulb. 6. Install the bulb and connector assembly into the taillight housing and rotate the connector one-quarter turn clockwise to lock it in place. 7. Reinstall the taillight housing. Changing the Backup Light 1. Open the trunk. 2. Rotate the bulb’s electrical connector one-quarter turn counterclockwise and remove it from the housing.
MAINTAINING YOUR VEHICLE 427 3. Remove the bulb from the connector socket and install the replacement bulb. 4. Install the bulb and connector assembly into the housing and rotate the connector one-quarter turn clockwise to lock it in place. License Plate Light 1. Remove two retaining screws holding the light lens in place. Location and Removal of Rear License Light Lens 2. Gently pry the lens loose. 3. Pull bulb from socket, replace and reattach the light lens with the two retaining screws.
428 MAINTAINING YOUR VEHICLE Center High-Mounted Stop Light (CHMSL) 1. Open the trunk lid. 2. Rotate the bulb’s electrical connector one-quarter turn counterclockwise and remove it from the CHMSL housing. High-mounted Stop Light Bulb Replacement 3. Remove the bulb from the connector socket and install the replacement bulb. 4. Install the bulb and connector assembly into the CHMSL housing and rotate the connector one-quarter turn clockwise to lock it in place.
MAINTAINING YOUR VEHICLE 429 FLUIDS AND CAPACITIES Engine U.S. Fuel (approximate) All FWD Engines — (Except 2.4L PZEV) 16.9 gallons 2.4L PZEV (Partial Zero Emissions Vehicle) 18.4 gallons Engine Oil with Filter 2.4 Liter Engine (SAE 5W-20, API Certified) 4.5 quarts 2.7 Liter Engine (SAE 5W-20, API Certified) 5.5 quarts 3.5 Liter Engine (SAE 10W-30, API Certified) 5.5 quarts Cooling System * 2.4 Liter Engine (Mopar威 Antifreeze/Coolant 5 Year/100,000 Mile For7.7 quarts mula) or equivalent. 2.
430 MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS, AND GENUINE PARTS Engine Component Engine Coolant Engine Oil (2.4L & 2.7L) Engine Oil (3.5L) Oil Filter (2.4L) Oil Filter (2.7L & 3.5L) Spark Plugs (2.4L - EXCEPT PZEV*) Spark Plugs (2.4L— with PZEV Spark Plugs (2.7L) Spark Plugs (3.5L) Fuel Selection (2.4L & 2.7L) Fluids, Lubricants, and Genuine Parts Mopar威 Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) or equivalent Use API Certified engine oil.
MAINTAINING YOUR VEHICLE Component Fuel Selection (2.7L - EXCEPT CALIE-85 Ethanol FORNIA EMISSION STATES) Fuel Selection (3.
432 MAINTAINING YOUR VEHICLE Chassis Component Automatic Transaxle Brake Master Cylinder Power Steering Reservoir Fluids, Lubricants and Genuine Parts Mopar威 ATF+4 Automatic Transmission Fluid. Mopar威 DOT 3 and SAE J1703 should be used. If DOT 3 brake fluid is not available, then DOT 4 is acceptable. Use only recommended brake fluids. Mopar威 ATF+4 Automatic Transmission Fluid.
MAINTENANCE SCHEDULES CONTENTS 䡵 Emissions Control System Maintenance . . . . . . . 434 䡵 Maintenance Schedule . . . . . . . . . . . . . . . . . . . 434 ▫ Required Maintenance Intervals . . . . . . . . . . .
M A I N T E N A N C E 434 MAINTENANCE SCHEDULES EMISSIONS CONTROL SYSTEM MAINTENANCE The Scheduled Maintenance services listed in bold type must be done at the times or mileages specified to ensure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
MAINTENANCE SCHEDULES NOTE: • The oil change indicator message will not monitor the time since the last oil change. Change your vehicles oil if it has been six months since your last oil change even if the oil change indicator message is NOT illuminated. • Change your engine oil more often if you drive your vehicle off-road for an extended period of time. • Under no circumstances should oil change intervals exceed 6,000 mi (10 000 km) or six months, whichever comes first.
M A I N T E N A N C E S C H E D U L E S 8 436 MAINTENANCE SCHEDULES NOTE: Six speed AutoStick威 Transaxle — if equipped is sealed, therefore checking the fluid level can only be done by a certified dealership service center. • Check all lights and other electrical items for correct operation. At Each Oil Change • Change the engine oil filter. • Inspect the brake hoses and lines. CAUTION! Failure to perform the required maintenance items may result in damage to the vehicle.
MAINTENANCE SCHEDULES 437 M Required Maintenance Intervals Perform Maintenance Every (Where time and mileage are listed, follow the interval that occurs first.) Maintenance Items Change the engine oil and engine oil filter. Rotate the tires. If using your vehicle in dusty or off-road conditions, inspect the engine air cleaner filter, and replace if necessary. Inspect the brake linings, and replace if necessary. Replace the air conditioning filter (if equipped). Inspect the CV joints.
M 438 MAINTENANCE SCHEDULES A I N T E N Maintenance Items A N Replace the spark plugs on 2.4L engines (except C PZEV* engine). E Inspect and adjust the power steering pump belt tenS C H E D U L E S 8 sion on 2.4L engines. Inspect the generator belt on 2.4L engines, and replace if necessary. Change the automatic transaxle fluid & filter if using your vehicle for any of the following: police, taxi, fleet, or frequent trailer towing. Inspect and replace the PCV valve if necessary.
MAINTENANCE SCHEDULES 439 M Perform Maintenance Every (Where time and mileage are listed, follow the interval that occurs first.) Maintenance Items Replace the timing belt on 2.4L and 3.5L engines. Change the automatic transaxle fluid & filter. Replace the accessory drive belt on 2.7L engines. *P artial Z ero E missions V ehicle WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the right equipment.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS 䡵 Suggestions For Obtaining Service For Your Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 443 ▫ In Mexico Contact . . . . . . . . . . . . . . . . . . . . . 444 ▫ Prepare For The Appointment . . . . . . . . . . . . 443 ▫ Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) . . . . . . . . . . . . . 445 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . . . 443 ▫ Service Contract . . . . . . . . . . . . . . . . . . . .
442 IF YOU NEED CONSUMER ASSISTANCE 䡵 Publication Order Forms . . . . . . . . . . . . . . . . . . 447 ▫ Traction Grades . . . . . . . . . . . . . . . . . . . . . . 449 䡵 Department Of Transportation Uniform Tire Quality Grades . . . . . . . . . . . . . . . . . . . . . . . . 449 ▫ Temperature Grades . . . . . . . . . . . . . . . . . . . 450 ▫ Treadwear . . . . . . . . . . . . . . . . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager. Keep a maintenance log of your vehicle’s service history. This can often provide a clue to the current problem.
444 IF YOU NEED CONSUMER ASSISTANCE special tools, and the latest information to ensure your vehicle is fixed correctly and in a timely manner. This is why you should always talk to your authorized dealer’s service manager first. Most matters can be resolved with this process. • If for some reason you are still not satisfied, talk to the general manager or owner of the authorized dealership. They want to know if you need assistance.
IF YOU NEED CONSUMER ASSISTANCE Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommunication Devices for the Deaf) equipment at its Customer Center. Any hearing or speech impaired customer, who has access to a TDD or a conventional teletypewriter (TTY) in the United States, can communicate with the manufacturer by dialing 1–800–380–CHRY.
446 IF YOU NEED CONSUMER ASSISTANCE WARNING! Engine exhaust, some of its constituents, and certain vehicle components contain, or emit, chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain, or emit, chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. WARRANTY INFORMATION (U.S.
IF YOU NEED CONSUMER ASSISTANCE 447 To contact NHTSA, you may either call the Auto Safety Hotline toll free at 1–888–327–4236 (TTY: 1–800–424– 9153), or go to http://www.safercar.gov; or write to: Administrator, NHTSA, 400 Seventh Street, SW., Washington, D.C. 20590. You can also obtain other information about motor vehicle safety from http://www.safercar.gov. PUBLICATION ORDER FORMS To order the following manuals, you may use either the website or the phone numbers listed below.
448 IF YOU NEED CONSUMER ASSISTANCE • Diagnostic Procedure Manuals. Filled with diagrams, charts and detailed illustrations, these practical manuals make it easy for students and technicians to find and fix problems on computercontrolled vehicle systems and features. They show exactly how to find and correct problems the first time, using step-by-step troubleshooting and driveability procedures, proven diagnostic tests and a complete list of all tools and equipment. • Owner’s Manuals.
IF YOU NEED CONSUMER ASSISTANCE DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES The following tire grading categories were established by the National Highway Traffic Safety Administration. The specific grade rating assigned by the tire’s manufacturer in each category is shown on the sidewall of the tires on your vehicle. All passenger car tires must conform to Federal safety requirements in addition to these grades.
450 IF YOU NEED CONSUMER ASSISTANCE Temperature Grades The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
INDEX 10
452 INDEX ABS (Anti-Lock Brake System) . . . . . . . . . . . . . . 282 Accessory Delay, Power . . . . . . . . . . . . . . . . . . . . 13 Adding Engine Coolant (Antifreeze) . . . . . . . . . . 396 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 332 Adding Washer Fluid . . . . . . . . . . . . . . . . . . 140,393 Additives, Fuel . . . . . . . . . . . . . . . . . . . . . . . . . 326 Air Cleaner, Engine (Engine Air Cleaner Filter) . . . 385 Air Conditioner Maintenance . . . . . . . . . . . .
INDEX Automatic Dimming Mirror . . . . . . . . . . . . . . . . . 86 Automatic Door Locks . . . . . . . . . . . . . . . . . . . 31,32 Automatic Oil Change Indicator . . . . . . . . 175,185,434 Automatic Temperature Control (ATC) . . . . . . . . . 248 Automatic Transaxle . . . . . . . . . . . . . . 13,264,270,403 Adding Fluid . . . . . . . . . . . . . . . . . . . 403,404,432 Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 405 Fluid and Filter Changes . . . . . . . . . . . . . . . . .
454 INDEX Break-In Recommendations, New Vehicle . . . . . . . . 78 Bulb Replacement . . . . . . . . . . . . . . . . . . . . . 417,418 Bulbs, Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . 417 Calibration, Compass . . . . . . . . . . . . . . . . . . . . . 188 Capacities, Antifreeze (Engine Coolant) . . . . . . . . . 20 Capacities, Fluid . . . . . . . . . . . . . . . . . . . . . . . . 429 Caps, Filler Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 332 Oil (Engine) . . .
INDEX Coin Holder . . . . . . . . . . . . . . . . . . . . . . . . . . . 157 Compact Disc (CD) Maintenance . . . . . . . . . . . . . 242 Compact Spare Tire . . . . . . . . . . . . . . . . . . . . . . 307 Compass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187 Compass Calibration . . . . . . . . . . . . . . . . . . . . . 188 Compass Variance . . . . . . . . . . . . . . . . . . . . . . . 189 Computer, Trip/Travel . . . . . . . . . . . . . . . . . . 20,186 Connector UCI . . . . . . . . . . . .
456 INDEX Delay (Intermittent) Wipers . . . . . . . . . . . . . . . 29,138 Diagnostic System, Onboard . . . . . . . . . . . . . . . . 377 Digital Video Disc (DVD) Player . . . . . . . . . . 222,225 Dimmer Switch, Headlight . . . . . . . . . . . . . . . . . 136 Dipsticks Automatic Transaxle . . . . . . . . . . . . . . . . . 403,404 Oil (Engine) . . . . . . . . . . . . . . . . . . . . . . . . . . 380 Disabled Vehicle Towing . . . . . . . . . . . . . . . . . . . 368 Disposal Antifreeze (Engine Coolant) . . .
INDEX Cooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 394 Exhaust Gas Caution . . . . . . . . . . . . . . . . . . . . 327 Fuel Requirements . . . . . . . . . . . . . . . . . . 323,429 Jump Starting . . . . . . . . . . . . . . . . . . . . . . . . . 364 Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . 380,429,430 Oil Change Interval . . . . . . . . . . . . 175,185,382,434 Oil Filler Cap . . . . . . . . . . . . . . . . . 374,375,376,383 Oil Filter . . . . . . . . . . . . . . . . . .
458 INDEX Fuel Requirements . . . . . . . . . . . . . . . . . . 328,329 Maintenance . . . . . . . . . . . . . . . . . . . . . . . 328,331 Replacement Parts . . . . . . . . . . . . . . . . . . . . . 331 Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 331 Flooded Engine Starting . . . . . . . . . . . . . . . . . . . 266 Floor Console . . . . . . . . . . . . . . . . . . . . . . . . . . 157 Fluid Capacities . . . . . . . . . . . . . . . . . . . . . . . . . 429 Fluid Leaks . . . . . . . . .
INDEX Fuel System Caution . . . . . . . . . . . . . . . . . . . . . 333 Fueling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 332 Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 412 Garage Door Opener (HomeLink威) . . . . . . . . . . . 144 Gas Cap (Fuel Filler Cap) . . . . . . . . . . . . 332,334,377 Gasoline, Clean Air . . . . . . . . . . . . . . . . . . . . . . 324 Gasoline (Fuel) . . . . . . . . . . . . . . . . . . . . . . . . . 323 Gasoline, Reformulated . . . . . .
460 INDEX Heated Seats . . . . . . . . . . . . . . . . . . . . . . . . Heater . . . . . . . . . . . . . . . . . . . . . . . . . . . . Heater, Engine Block . . . . . . . . . . . . . . . . . . Hitches Trailer Towing . . . . . . . . . . . . . . . . . . . . . HomeLink威 (Garage Door Opener) Transmitter Hood Prop . . . . . . . . . . . . . . . . . . . . . . . . . Hood Release . . . . . . . . . . . . . . . . . . . . . . . Hoses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ignition . . . . . . . . . .
INDEX Keyless Entry System . . . . . . Keyless Entry System (Sedan) Keys . . . . . . . . . . . . . . . . . Knee Bolster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 . . 21 . . 12 52,53 Lane Change and Turn Signals . . . . . . . . . . . . . . 179 Lap/Shoulder Belts . . . . . . . . . . . . . . . . . . . . . . . 42 LATCH (Lower Anchors and Tether for CHildren) . 73 Latches Hood . . . . . . . . . .
462 INDEX Seat Belt Reminder . . . . . . . . . . . . . . . . . . . . . 173 Security Alarm (Theft Alarm) . . . . . . . . . . . . . . 19 Theft Alarm (Security Alarm) . . . . . . . . . . . . . . 173 Tire Pressure Monitoring (TPMS) . . . . . . . . . . . 314 Traction Control . . . . . . . . . . . . . . . . . . . . . . . 287 Turn Signal . . . . . . . . . . . . . . . . . . 135,179,422,424 Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173 Warning (Instrument Cluster Description) . . . . .
INDEX Monitor, Tire Pressure System . . . . . . . . . . . . . . . 314 Mopar Parts . . . . . . . . . . . . . . . . . . . . . . . . . 379,446 MP3 Player . . . . . . . . . . . . . . . . . . . . . . . . . 222,225 MTBE/ETBE . . . . . . . . . . . . . . . . . . . . . . . . . . . 324 Navigation Radio . . . . . . . . . . . . . . . . . . . . . . . . 225 Navigation System . . . . . . . . . . . . . . . . . . . . . . . 225 New Vehicle Break-In Period . . . . . . . . . . . . . . . . 78 Occupant Restraints . . . . . . .
464 INDEX Paint Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 406 Panic Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Parking Brake . . . . . . . . . . . . . . . . . . . . . . . . . . 277 Parking On Hill . . . . . . . . . . . . . . . . . . . . . . . . . 278 Passing Light . . . . . . . . . . . . . . . . . . . . . . . . . . . 134 Personal Settings . . . . . . . . . . . . . . . . . . . . . . . . 190 Pets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Radio Operation . . . . . . . . . . . . . . . . . . . 223,226,242 Radio, Satellite . . . . . . . . . . . . . . 222,223,225,227,234 Radio (Sound Systems) . . . . . . . . . . . . . . . . . 222,225 Rear Cup Holder . . . . . . . . . . . . . . . . . . . . . . . . 161 Rear Seat, Folding . . . . . . . . . . . . . . . . . . . . 128,129 Rear Wheel Bearings . . . . . . . . . . . . . . . . . . . . . 406 Rear Window Defroster . . . . . . . . . . . . . . . . . . . 258 Rear Window Features . . . . . . . . . . . .
466 INDEX Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78 Satellite Radio . . . . . . . . . . . . . . . 222,223,225,227,234 Satellite Radio Antenna . . . . . . . . . . . . . . . . . . . 235 Schedule, Maintenance . . . . . . . . . . . . . . . . . . . . 434 Seat Belt Maintenance . . . . . . . . . . . . . . . . . . . . . 411 Seat Belt Reminder . . . . . . . . . . . . . . . . . . . . . . . 49 Seat Belts Adjustable Shoulder Belt . . . . . . . . . . . . . . . . . .
INDEX Settings, Personal . . . . . . . . . . . . . . . . . . . . . . . . 190 Shoulder Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Side Window Demisters (Defrosters) . . . . . . . . . . 255 Signals, Turn . . . . . . . . . . . . . . . . . . . . . . . . . . . 424 Slippery Surfaces, Driving On . . . . . . . . . . . . . . . 291 Snow Chains (Tire Chains) . . . . . . . . . . . . . . . . . 312 Snow Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . 312 Sound Systems (Radio) . . . . .
468 INDEX Theft Alarm (Security Alarm) . . . . . . . . . . . . . . . . 18 Theft System (Security Alarm) . . . . . . . . . . . . . . . 18 Tilt Steering Column . . . . . . . . . . . . . . . . . . . . . 140 Time Delay, Headlight . . . . . . . . . . . . . . . . . . . . 133 Tip Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 266 Tire and Loading Information Placard . . . . . . . . . 299 Tire Identification Number (TIN) . . . . . . . . . . . . . 298 Tire Markings . . . . . . . . . . . . . . .
INDEX Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 341 Recreational . . . . . . . . . . . . . . . . . . . . . . . 349,369 Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 341 Towing Assistance . . . . . . . . . . . . . . . . . . . . . . . 102 Traction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 292 Trailer Towing . . . . . . . . . . . . . . . . . . . . . . . . . . 338 Cooling System Tips . . . . . . . . . . . . . . . . . . . . 349 Hitches . . . . . . .
470 INDEX UCI Connector . . . . . . . . . . . . . . . . . . . . . . . . . 229 UConnect™ (Hands-Free Phone) . . . . . . . . . . . 89,225 Understanding Your Instrument Panel . . . . . . . . . 169 Uniform Tire Quality Grades . . . . . . . . . . . . . . . . 449 Universal Consumer Interface (UCI) Connector . . . 229 Universal Serial Bus (USB) Port . . . . . . . . . . . 222,225 Universal Transmitter . . . . . . . . . . . . . . . . . . . . . 144 Unleaded Gasoline . . . . . . . . . . . . . . . . . . . . . . .
INDEX Wheel Bearings . . . . . . . . . . . . . . . . . . . . . . . . . 406 Wind Buffeting . . . . . . . . . . . . . . . . . . . . . . . 38,153 Window Fogging . . . . . . . . . . . . . . . . . . . . . . . . 255 Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Windshield Defroster . . . . . . . . . . . . . . . 245,246,252 Windshield Washers . . . . . . . . . . . . . . . . . . . 136,140 Fluid . . . . . . . . . . . . .
472 INDEX Alignment and Balance . . . . . . . . . . . . . . . . . . . 312 Alterations/Modifications, Vehicle . . . . . . . . . . . . . 7 Antenna, Satellite Radio . . . . . . . . . . . . . . . . . . . 235 Antifreeze (Engine Coolant) . . . . . . . . . . . 395,396,429 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . 398 Anti-Lock Brake System (ABS) . . . . . . . . . . . . . . 282 Anti-Lock Warning Light . . . . . . . . . . . . . . . . . . 282 Anti-Theft Security Alarm (Theft Alarm) . . . . .
INDEX Bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 406 Belts, Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . 384 Body Mechanism Lubrication . . . . . . . . . . . . . . . 392 B-Pillar Location . . . . . . . . . . . . . . . . . . . . . . . . 299 Brake Assist System . . . . . . . . . . . . . . . . . . . . . . 286 Brake, Parking . . . . . . . . . . . . . . . . . . . . . . . . . . 277 Brake System . . . . . . . . . . . . . . . . . . . . . . . . 281,400 Anti-Lock (ABS) . .
474 INDEX Chains, Tire . . . . . . . . . . . . . . . . . . . . . . . . . . . . 312 Changing A Flat Tire . . . . . . . . . . . . . . . . . . . . . 356 Chart, Tire Sizing . . . . . . . . . . . . . . . . . . . . . . . . 296 Check Engine Light (Malfunction Indicator Light) . . . . . . . . . . . . . . . 378 Child Restraint . . . . . . . . . . . . . . . . . . . . 67,69,73,76 Child Restraint Tether Anchors . . . . . . . . . . . . . 71,73 Child Safety Locks . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Pressure Cap . . . . . . . . . . . . . . . . . . . . . . . . . 397 Radiator Cap . . . . . . . . . . . . . . . . . . . . . . . . . 397 Selection of Coolant (Antifreeze) . . . . . . 395,429,430 Corrosion Protection . . . . . . . . . . . . . . . . . . . . . 406 Crankcase Ventilation Module . . . . . . . . . . . . . . . 20 Cruise Light . . . . . . . . . . . . . . . . . . . . . . . . . . . 176 Cup Holder . . . . . . . . . . . . . . . . . . . . . . 129,160,411 Customer Assistance . . . . . . . . . . . . .
476 INDEX Electrical Power Outlets . . . . . . . . . . . . . . . . . . . 154 Electronic Speed Control (Cruise Control) . . . . . . 141 Electronic Stability Program (ESP) . . . . . . . . . . . . 287 Electronic Vehicle Information Center (EVIC) . . . . 183 Emergency, In Case of Jacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 356 Jump Starting . . . . . . . . . . . . . . . . . . . . . . . . . 364 Towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 368 Emergency Trunk Release .
INDEX Fabric Care . . . . . . . . . . . . . . . . . . . . . . . . . 408,409 Filler Location Fuel . . . . . . . . . . . . . . . . . . . . 172,332 Filters Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . 385 Air Conditioning . . . . . . . . . . . . . . . . . . . . 256,389 Automatic Transaxle . . . . . . . . . . . . . . . . . . . . 405 Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . 384,430 Engine Oil Disposal . . . . . . . . . . . . . . . . . . . . 384 Flashers . . . . . . . . . . .
478 INDEX Additives . . . . . . . . . . . . . . . . . . . . . . . . . . . . 326 Clean Air . . . . . . . . . . . . . . . . . . . . . . . . . . . . 324 Ethanol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 324 Filler Cap (Gas Cap) . . . . . . . . . . . . . . . . . 172,332 Filler Door (Gas Cap) . . . . . . . . . . . . . . . . . . . 172 Gasoline . . . . . . . . . . . . . . . . . . . . . . . . . . . . 323 Gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172 Hoses . . . . . . . . .
INDEX Hands-Free Phone (UConnect™) . . . . . . . . 89,225,227 Hard Drive (HDD) . . . . . . . . . . . . . . . . . . . . 222,225 Hazard Driving Through Flowing, Rising, or Shallow Standing Water . . . . . . . . . . . . . . . . . . . . . . . . . 292 Hazard Warning Flasher . . . . . . . . . . . . . . . . . . . 353 Head Restraints . . . . . . . . . . . . . . . . . . . . . . . . . 125 Headlights . . . . . . . . . . . . . . . . . . . . . . . . . . . . 418 Bulb Replacement . . . . . . . . . . . . . . . . . . . . .
480 INDEX Instrument Panel Lens Cleaning . . . . . . . . . . . . . 410 Integrated Power Module (Fuses) . . . . . . . . . . . . 412 Interior Appearance Care . . . . . . . . . . . . . . . . . . 408 Interior Lights . . . . . . . . . . . . . . . . . . . . . . . . . . 131 Intermittent Wipers (Delay Wipers) . . . . . . . . . . . 138 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Jack Location . . . . . . . . . . . . . . . . . . . . . . . . . . . 356 Jack Operation . . . . . . . . . . .
INDEX Fog . . . . . . . . . . . . . . . . . . . . . . . . . . 134,179,422 Headlight Switch . . . . . . . . . . . . . . . . . . . . . . 132 Headlights . . . . . . . . . . . . . . . . . . . . . . . . . . . 132 Headlights On With Wipers . . . . . . . . . . . . . . . 139 High Beam Indicator . . . . . . . . . . . . . . . . . . . . 182 Illuminated Entry . . . . . . . . . . . . . . . . . . . . . . . 20 Instrument Cluster . . . . . . . . . . . . . . . . . . . . . 132 Interior . . . . . . . . . . . . . . . . . . .
482 INDEX Maintenance, General . . . . . . . . . . . . . . . . . . . . . 380 Maintenance Procedures . . . . . . . . . . . . . . . . . . . 380 Maintenance Schedule . . . . . . . . . . . . . . . . . . . . 434 Malfunction Indicator Light (Check Engine) . . 182,378 Manual, Service . . . . . . . . . . . . . . . . . . . . . . . . . 447 Map/Reading Lights . . . . . . . . . . . . . . . . . . . . . 131 Master Cylinder (Brakes) . . . . . . . . . . . . . . . . . . 402 Methanol . . . . . . . . . . . . . . . . . . . .
INDEX Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . 384,430 Filter Disposal . . . . . . . . . . . . . . . . . . . . . . . . 384 Identification Logo . . . . . . . . . . . . . . . . . . . . . 382 Materials Added to . . . . . . . . . . . . . . . . . . . . . 384 Recommendation . . . . . . . . . . . . . . . . . . . 382,429 Synthetic . . . . . . . . . . . . . . . . . . . . . . . . . . . . 383 Viscosity . . . . . . . . . . . . . . . . . . . . . . . . . . 383,429 Oil Filter, Change . . . . . . . .
484 INDEX Steering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 290 Steering, Checking . . . . . . . . . . . . . . . . . . . . . 391 Sunroof . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151 Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Power Steering Fluid . . . . . . . . . . . . . . . . . . . . . 391 Pregnant Women and Seat Belts . . . . . . . . . . . . . . 51 Preparation for Jacking . . . . . . . . . . . . . . . . . . . . 357 Pretensioners Seat Belts . .
INDEX Remote Trunk Release . . . . . . . . . . . . . . . . . . . . . 38 Replacement Bulbs . . . . . . . . . . . . . . . . . . . . . . . 417 Replacement Keys . . . . . . . . . . . . . . . . . . . . . . . . 16 Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . 379 Replacement Tires . . . . . . . . . . . . . . . . . . . . . . . 310 Reporting Safety Defects . . . . . . . . . . . . . . . . . . . 446 Resetting Oil Change Indicator . . . . . . . . . . . 175,185 Restraint, Head . . . . . . . . . . . .
486 INDEX Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . 129,409 Head Restraints . . . . . . . . . . . . . . . . . . . . . . . 125 Heated . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126 Lumbar Support . . . . . . . . . . . . . . . . . . . . . . . 124 Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124 Rear Folding . . . . . . . . . . . . . . . . . . . . . . . 128,129 Rear Folding (Sedan) . . . . . . . . . . . . . . . . . . . . 162 Reclining . . . . . . . . . . .
INDEX Wheel, Tilt . . . . . . . . . . . . . . . . . . . . . . . . . . . 140 Steering Wheel Mounted Sound System Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 238 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162,417 Storage, Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . 255 Stuck, Freeing . . . . . . . . . . . . . . . . . . . . . . . . . . 367 Sun Roof . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
488 INDEX Life of Tires . . . . . . . . . . . . . . . . . . . . . . . . . . 309 Load Capacity . . . . . . . . . . . . . . . . . . . . . 299,300 Pressure Monitor System (TPMS) . . . . . . . . . . . 314 Quality Grading . . . . . . . . . . . . . . . . . . . . . . . 449 Radial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 306 Replacement . . . . . . . . . . . . . . . . . . . . . . . . . 310 Rotation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 313 Safety . . . . . . . . . . . . . .
INDEX Selection of Lubricant . . . . . . . . . . . . . . . . . . . 432 Transmission Range Indicator . . . . . . . . . . . . . . . . . . . . . . . 174 Transmitter Battery Service (Remote Keyless Entry) . . . . . . . . . . . . . . . . . . . . 25 Transmitter, Garage Door Opener (HomeLink威) . . 144 Transmitter Programming (Remote Keyless Entry) . . . . . . . . . . . . . . . . . . . . 25 Transporting Pets . . . . . . . . . . . . . . . . . . . . . . . . 77 Tread Wear Indicators . . . . . . . . . . . . . . . . .
490 INDEX Video Entertainment System (Rear Seat Video System) . . . . . . . . . . . . . . . . . . 240 Viscosity, Engine Oil . . . . . . . . . . . . . . . . . . . . . . 383 Voice Recognition System (VR) . . . . . . . . . . . . . . 116 Warning Lights (Instrument Cluster Description) . . . . . . . . . . . . . 172 Warnings and Cautions . . . . . . . . . . . . . . . . . . . . . 6 Warranty Information . . . . . . . . . . . . . . . . . . . . . 446 Washer, Adding Fluid . . . . . . . . . . . . . . . . . .
INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained personnel. The following must be observed during installation. The positive power connection should be made directly to the battery and fused as close to the battery as possible.
2008 Sebring 2008 OWNER’ S MANUAL 81-026-0804 Second Edition Printed in U.S.A.
