SECTION TABLE OF CONTENTS PAGE 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83 3 4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION CONTENTS 䡵 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 Vehicle Identification Number . . . . . . . . . . . . . . . 6 䡵 How To Use This Manual . . . . . . . . . . . . . . . . . . 4 䡵 Vehicle Modifications / Alterations . . . . . . . . . . . 7 䡵 Warnings And Cautions . . . . . . . . . . . . . . . . . . .
INTRODUCTION INTRODUCTION This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a Warranty Information Booklet and various customer oriented documents. You are urged to read these publications carefully. Following the instructions and recommendations in this manual will help assure safe and enjoyable operation of your vehicle.
INTRODUCTION 5 1
INTRODUCTION WARNINGS AND CAUTIONS This manual contains WARNINGS against operating procedures which could result in an accident or bodily injury. It also contains CAUTIONS against procedures which could result in damage to your vehicle. If you do not read this entire manual you may miss important information. Observe all Warnings and Cautions. VEHICLE IDENTIFICATION NUMBER The vehicle identification number (VIN) is found on the left front corner of the instrument panel, visible through the windshield.
INTRODUCTION 7 VEHICLE MODIFICATIONS / ALTERATIONS 1 WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS 䡵 A Word About Your Keys . . . . . . . . . . . . . . . . . .12 䡵 Sentry Key — If Equipped . . . . . . . . . . . . . . . . .15 ▫ Ignition Key Removal . . . . . . . . . . . . . . . . . . .12 ▫ Shaft Lock Module (Vehicles Equipped With Premium Security System) — If Equipped . . . . .16 ▫ Key-In-Ignition Reminder . . . . . . . . . . . . . . . .14 ▫ Locking Doors With The Key . . . . . . . . . . . . . .14 䡵 Steering Wheel Lock — If Equipped . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ To Disarm The System . . . . . . . . . . . . . . . . . . .19 ▫ Power Door Locks . . . . . . . . . . . . . . . . . . . . .28 ▫ Security System Manual Override . . . . . . . . . . .19 ▫ Child Protection Door Lock . . . . . . . . . . . . . . .31 䡵 Illuminated Entry System . . . . . . . . . . . . . . . . . .20 䡵 Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33 䡵 Remote Keyless Entry . . . . . . . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 ▫ Seat Belt Extender . . . . . . . . . . . . . . . . . . . . . .49 䡵 Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . .79 ▫ Driver And Front Passenger Supplemental Restraint System - Airbag . . . . . . . . . . . . . . . .50 ▫ Exhaust Gas . . . . . . . . . . . . . . . . . . . . . . . . . .79 ▫ Event Data Recorder (EDR) . . . . . . . . . . . . . . .65 ▫ Child Restraint . . . . . . . . . . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS The dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys from your dealer. Ask your dealer for these numbers and keep them in a safe place. Three Button Key Ignition Key Removal Automatic Transaxle Place the shift lever in PARK.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 NOTE: If you try to remove the key before you place the lever in PARK, the key may become trapped temporarily in the ignition cylinder. If this occurs, rotate the key to the right slightly, then remove the key as described. If a malfunction occurs, the system will trap the key in the ignition cylinder to warn you that this safety feature is inoperable. The engine can be started and stopped but the key cannot be removed until you obtain service.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Key-In-Ignition Reminder If you open the driver’s door and the key is in the ignition switch, a chime will sound to remind you to remove the key. Locking Doors With The Key You can insert the key with either side up. To lock the door, turn the key rearward, to unlock the door, turn the key forward. See Section 7 of this manual for door lock lubrication. STEERING WHEEL LOCK — IF EQUIPPED Your vehicle may be equipped with a passive steering wheel lock.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 Automatic Transaxle Ignition Interlock System This system prevents the key from being removed unless the shift lever is in PARK. It also prevents shifting out of PARK unless the key is in the ACC, or ON positions, and the brake pedal is depressed. SENTRY KEY — IF EQUIPPED The Sentry Key Immobilizer System prevents unauthorized vehicle operation by disabling the engine. The system does not need to be armed or activated.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Shaft Lock Module (Vehicles Equipped with Premium Security System) — If Equipped The shaft lock module is located inside the steering column. The module works in conjunction with the Sentry Key to prevent the steering shaft from rotating if someone inserts an invalid ignition key into the ignition lock cylinder in the instrument panel. NOTE: • The Sentry Key Immobilizer System is not compatible with remote starting systems.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 NOTE: When having the Sentry Key Immobilizer System serviced, bring all vehicle keys with you to the dealer. Customer Key Programming You can program new sentry keys to the system if you have two valid sentry keys by performing the following procedure: 1. Cut the additional Sentry Key Transponder blank(s) to match the ignition switch lock cylinder key code. 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE General Information The Sentry Key system complies with FCC rules part 15 and with RSS-210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference that may be received, including interference that may cause undesired operation. SECURITY ALARM SYSTEM — IF EQUIPPED This system monitors the vehicle doors and ignition for unauthorized operation.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 NOTE: If the SECURITY light stays on continuously during vehicle operation, have the system checked by your dealer. To Disarm the System: Use the Keyless Entry transmitter to unlock the door. If something has triggered the system in your absence, the horn will sound three times when you unlock the doors and the security lamp will flash for 30 seconds. Check the vehicle for tampering.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ILLUMINATED ENTRY SYSTEM The courtesy lights will turn on when you use the keyless entry transmitter or open the doors. The lights will fade to off after about 30 seconds or they will immediately fade to off once the ignition switch is turned on. NOTE: • The front courtesy overhead console, door courtesy and liftgate lights do not turn on if the dimmer control is in the interior lights ON position (extreme top position).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 Two (2) transmitters may be supplied with the vehicle. Vehicles built without the powered options will be equipped from the factory with three button transmitters and those built with power options will be equipped with six button transmitters. To unlock the doors and liftgate: Press and release the UNLOCK button on the transmitter once to unlock the driver’s door, or twice to unlock all doors and liftgate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • On non EVIC – equipped vehicles perform the following steps: 1. Perform this operation while standing outside the vehicle. 2. Press and hold the UNLOCK button on your key fob. 3. Continue to hold the UNLOCK button, wait at least 4 seconds, but no longer than 10 seconds, then press and hold the LOCK button. Release both buttons at the same time. 4. This will allow you to unlock all doors on the first press of the UNLOCK button. 5.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 • On non EVIC – equipped vehicles perform the following steps: 1. Perform this operation while standing outside the vehicle. 2. Press and hold the LOCK button on your key fob. 3. Continue to hold the LOCK button, wait at least 4 seconds, but no longer than 10 seconds, then press and hold the PANIC button. Release both buttons at the same time. 4. To reactivate the feature, repeat this procedure. 5.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • On electronic vehicle information center (EVIC) equipped vehicles refer to “Flash Lights On Lock/ Unlock?” under “Use Factory Settings?” in the EVIC section of this manual. • On non EVIC - equipped vehicles perform the following steps: 1. Perform this operation while standing outside the vehicle. 2. Press and hold the LOCK button on your key fob. 3.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 Programming Additional Transmitters Refer to SENTRY KEY “Customer Key Programming.” NOTE: If you do not have a programmed transmitter, contact your authorized dealer for assistance. 2 Battery Replacement The recommended replacement battery is CR2032 battery. NOTE: Do not touch the battery terminals that are on the back housing or the printed circuit board. 1.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Remove and replace the battery. Avoid touching the new battery with your fingers. Skin oils may cause battery deterioration. If you touch a battery, clean it with rubbing alcohol. 3. To reassemble the transmitter case, snap the two halves together. Make sure there is an even “gap” between the two halves. Test transmitter operation. General Information This device complies with part 15 of the FCC rules and RSS 210 of Industry Canada.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 DOOR LOCKS Manual Door Locks Lock the doors by pushing up on the lock knob on each door trim panel. If the lock knob is up when you shut the door, the door will lock. Therefore, make sure the keys are not inside the vehicle before closing the door. WARNING! • For personal security and safety in the event of an accident, lock the vehicle doors as you drive as well as when you park and leave the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Power Door Locks A power door lock switch is on each front door trim panel. Use this switch to lock or unlock the doors. locks will not operate. This prevents you from accidentally locking your keys in the vehicle. Removing the key or closing the door will allow the locks to operate. A chime will sound if the key is in the ignition and a door is open, as a reminder to remove the key.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 If desired, the “Auto Door Locks?” feature can be turned on or off by using the following procedure: • On electronic vehicle information center (EVIC) equipped vehicles refer to “Auto Door Locks?” under “Use Factory Settings?” in the EVIC section of this manual. 4. Within 15 seconds cycle the key from the LOCK position to the ON/RUN position a minimum of four times; ending in the LOCK position (Do not start the engine). 5.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE This feature will not operate if there is any manual operation of the power door locks (Lock or Unlock). If desired, the “Auto Unlock On Exit?” feature can be turned on or off by using the following procedure: 4. Within 15 seconds, cycle the key from the LOCK position to the ON/RUN position a minimum of four times ending in the LOCK position (do not start the engine).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 Child Protection Door Lock To provide a safer environment for small children riding in the rear seats, the rear doors are equipped with a child protection door lock system. 2 NOTE: When the child lock system is engaged, the door can be opened only by using the outside door handle even though the inside door lock is in the unlocked position. To Engage the Child Protection Door Lock 1. Open the rear door. 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: For emergency exit with the system engaged, move the door lock knob to the UNLOCK position, roll down the window and open the door with the outside door handle. WARNING! Avoid trapping anyone in the vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged. To Disengage the Child Protection Door Lock 1. Open the rear door. 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 WINDOWS Power Windows The window controls on the driver’s door control all the door windows. The switches will operate only when the ignition switch is in the ON or ACCESSORY position. The window lock switch on the driver’s door allows you to disable the window controls on the passenger doors. When the lock switch is pressed the window controls on the passenger doors will not illuminate and the passenger windows will be disabled.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The time is customer programmable through the Electronic Vehicle Information Center (EVIC). Refer to “Power Accessory Delay?” under “Personal Settings (Customer Programmable Features)” in Section 4 of this manual for details. Auto Up Feature with Anti–Pinch Protection — If Equipped Lift the window switch to the second detent, release, and the window will go up automatically.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 Reset Any time the vehicle battery is disconnected, or goes dead, the auto-up function will be disabled. To reactivate the auto-up feature, perform the following steps after vehicle power is restored: 1. Pull the window switch up to close window completely and continue to hold the switch up for an additional two seconds after the window is closed. 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Once unlocked, on vehicles equipped with power locks, the liftgate can be opened or closed without using the key. To open the liftgate, depress the liftgate release switch located on the underside of the license plate bar and pull the liftgate open with one fluid motion. The liftgate will not manually open if the vehicle is in gear or the vehicle speed is above 0 mph (0 km/h).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 Power Liftgate — If Equipped The power liftgate may be opened manually or by using the button on the remote keyless entry transmitter. Press the button on the remote keyless entry transmitter twice within five seconds, to open the power liftgate. Once the liftgate is fully open, pressing the button twice within five seconds a second time will close the liftgate. 2 The power liftgate may also be opened by pressing the button located on the overhead console.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE When the remote button is pressed the “Lamp Flash” feature is enabled the tail lights will flash to signal that the liftgate is opening or closing. A beeping signal will sound two seconds before the liftgate starts to open or close. NOTE: • If anything obstructs the power liftgate while it is closing or opening, the liftgate will automatically reverse to the closed or open position, provided it meets sufficient resistance.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 • The power liftgate switches will not operate if the vehicle is in gear or the vehicle speed is above 0 mph (0 km/h). • The power liftgate will not operate in temperatures below ⫺12° F (⫺24° C) or temperatures above 143° F (62° C). Be sure to remove any build-up of snow or ice from the liftgate before pressing any of the power liftgate switches.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE OCCUPANT RESTRAINTS Some of the most important safety features in your vehicle are the restraint systems. These include the front and rear seat belts for the driver and all passengers, front airbags for both the driver and front passenger, and if equipped, left and right window bags for the driver and passengers seated next to a window and a driver inflatable knee blocker.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 Please pay close attention to the information in this section. It tells you how to use your restraint system properly to keep you and your passengers as safe as possible. WARNING! In a collision, you and your passengers can suffer much greater injuries if you are not properly buckled up. You can strike the interior of your vehicle or other passengers, or you can be thrown out of the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • Be sure everyone in your vehicle is in a seat and using a seat belt properly. • Wearing a seat belt incorrectly is dangerous.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2 2. The seat belt latch plate is near the seatback of the front seats and next to your arm in the rear seats. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to allow the belt to go around your lap.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click”. Latch Plate To Buckle WARNING! • A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you as well.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision. WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Seat belt assemblies must be replaced after a collision if they have been damaged (bent retractor, torn webbing, etc.).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 Lap/Shoulder Belt Untwisting Procedure Use the following procedure to untwist a twisted lap/ shoulder belt. 1. Position the latch plate as close as possible to the anchor point. 2. At about 6 to 12 inches (15 to 30 cm) above the latch plate, grasp and twist the belt webbing 180° to create a fold that begins immediately above the latch plate. 3. Slide the latch plate upward over the folded webbing.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Enhanced Seat Belt Use Reminder System (BeltAlert) — Driver Front Seat Only If the occupied driver’s seat belt has not been buckled within 60 seconds of starting the vehicle and if the vehicle speed is greater than 5 mph (8 km/h), the Enhanced Warning System (BeltAlert) will alert the driver to buckle their seat belt. The driver should also instruct all other occupants to buckle their seat belts.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 3. Within 60 seconds of turning the ignition switch to the ON/RUN position, unbuckle and then re-buckle the driver’s seat belt at least three times within 10 seconds, ending with the seat belt buckled. Seat Belts and Pregnant Women We recommend that pregnant women use the seat belts throughout their pregnancies. Keeping the mother safe is the best way to keep the baby safe.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Using a seat belt extender when not needed can increase the risk of injury in a collision. Only use when the lap belt is not long enough when it is worn low and snug, and in the recommended seating positions. Remove and store the extender when not needed. Driver and Front Passenger Supplemental Restraint System - Airbag This vehicle has airbags for both the driver and front passenger as a supplement to the seat belt restraint systems.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 Also, the front passenger airbag is certified to the Federal regulations that define Occupant Classification (Refer to “Occupant Classification System” in this section). 2 This vehicle may also be equipped with a driver inflatable knee blocker located on the instrument panel below the steering column. This vehicle may also be equipped with left and right window bags to protect the driver and passengers sitting next to a window.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Do not put anything on or around the airbag covers or attempt to manually open them. You may damage the airbags and you could be injured because the airbags are not there to protect you. These protective covers for the airbag cushions are designed to open only when the airbags are inflating.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 If your vehicle is equipped, the window bag on the crash side of the vehicle is triggered in moderate to severe side collisions. But even in collisions where the airbags inflate, you need the seat belts to keep you in the right position for the airbags to protect you properly. Here are some simple steps you can take to minimize the risk of harm from a deploying airbag. 1. Children 12 years old and under should always ride buckled up in a rear seat.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE You should read the instructions provided with your child restraint to make sure that you are using it properly. 2. All occupants should wear their lap and shoulder belts properly. 3. The driver and front passenger seats should be moved back as far as practical to allow the front airbags room to inflate. 4. If your vehicle has left and right window bags, do not lean against the door, airbags will inflate forcefully into the space between you and the door.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 Airbag System Components • Seat Belt Reminder Light The airbag system consists of the following: • Knee Impact Bolster • Occupant Restraint Controller (ORC) • Driver Inflatable Knee Blocker • AIRBAG Light • Front Passenger Seat Occupant Classification System (OCS) — If Equipped • Driver Airbag • Front Passenger Airbag − Occupant Classification Module • Supplemental Side Curtain Airbags (If Equipped) − Passenger Airbag Disabled (PAD) Indicator Light
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE How The Airbag System Works • The Occupant Restraint Controller (ORC) determines if a frontal collision is severe enough to require the airbags to inflate. Based on the level of collision severity, the front control module determines the proper rate of inflation. The front airbag inflators are designed to provide different rates of airbag inflation.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 WARNING! Ignoring the AIRBAG warning light in your instrument panel could mean you won’t have the airbags to protect you in a collision. If the light does not come on, stays on after you start the vehicle, or if it comes on as you drive, have the airbag system checked right away. • The Driver and Passenger Airbag/Inflator Units are located in the center of the steering wheel and the right side of the instrument panel.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE about 30 milliseconds (about one quarter of the time it takes to blink your eyes) with enough force to injure you if you are not belted and seated properly, or if items are positioned in the area where the window bag inflates. This especially applies to children. The window bag is only about 31⁄2 inches (9 cm) thick when it is inflated.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 If there is a rapid change in temperature or humidity, the OCS may not be able to properly approximate occupant size. If your seat including your trim cover and cushion needs to be serviced in any way (including removal or loosening/tightening of seat attachment bolts), take the vehicle to your authorized dealer. Only manufacturer approved seat accessories may be used. OFF when the OCS has determined that the occupant size category is a child.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE For almost all sizes of properly seated adults, the airbag will be enabled in the event of a collision. For small teenagers and some small adults, depending on size, the airbag may or may not be enabled in the event of a collision. Both drivers and passengers should always use the PAD indicator light as an indication if the front passenger is properly positioned or not.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 • The Passenger Airbag Disabled (PAD) Indicator Light indicates to the driver and passenger when the airbag is turned OFF in the presence of a properly seated occupant. When the PAD indicator light is illuminated, the airbag is OFF. Also, when the Occupant Classification System (OCS) detects either an empty seat of a weight less than the predetermined occupant threshold, the ORC will not illuminate the PAD indicator light even though the airbag is turned off.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Unapproved modifications or service procedures to the front passenger seat assembly, its related components, or seat cover may inadvertently change the airbag deployment in case of a frontal crash. This could result in death or serious injury to the front seat passenger if the vehicle is involved in an accident. A modified vehicle may not comply with required Federal Motor Vehicle Safety Standards (FMVSS).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 If A Deployment Occurs The airbag system is designed to deploy the airbags when the ORC and impact sensors detect a moderate-tosevere collision, to help restrain the vehicle passengers, and then immediately deflate. NOTE: A collision that is not severe enough to need airbag protection will not activate the system. This does not mean something is wrong with the airbag system.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Deployed airbags, front seat belt buckle pretensioners and driver inflatable knee blocker cannot protect you in another collision. Have the airbags, front seat belt buckle pretensioners and driver inflatable knee blocker replaced by an authorized dealer as soon as possible. Also, have the Occupant Classification System serviced as well.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 WARNING! • You need proper knee impact protection in a collision. Do not mount or locate any aftermarket equipment on or behind the knee bolsters. • It is dangerous to try to repair any part of the airbag system yourself. Be sure to tell anyone who works on your vehicle that it has airbags. Airbag Light You will want to have the airbags ready to inflate for your protection in a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE data gathered during a complete accident investigation, the electronic data may be used by DaimlerChrysler Corporation and others to learn more about the possible causes of crashes and associated injuries in order to assess and improve vehicle performance.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 Data Parameters that May Be Recorded: • Diagnostic trouble code(s) and warning lamp status for electronically-controlled safety systems, including the airbag system • Airbag disable lamp status (if equipped) • ⬙Time⬙ of airbag deployment (in terms of ignition cycles and vehicle mileage) • Airbag deployment level (if applicable) • Seat belt status • Brake status (service and parking brakes) • Accelerator status (including vehicle speed) • Engine control status
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! In a collision, an unrestrained child, even a tiny baby, can become a missile inside the vehicle. The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are. The child and others could be badly injured. Any child riding in your vehicle should be in a proper restraint for the child’s size.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 • Rearward-facing child seats must NEVER be used in the front seat of a vehicle with a front passenger airbag. An airbag deployment could cause severe injury or death to infants in this position. Older Children and Child Restraints Children who weigh more than 20 lbs (9 kg) and who are older than one year can ride forward-facing in the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE and use the lap belt. Never allow a child to put the shoulder belt under an arm or behind their back. NOTE: For additional information, refer www.seatcheck.org or call 1-866-SEATCHECK. to WARNING! • Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 shoulder portion of the lap/shoulder belt will tighten the belt. The cinching latch plate will keep the belt tight, however, any seat belt system will loosen with time, so check the belt occasionally and pull it tight if necessary. • In the rear seat, you may have trouble tightening the lap/shoulder belt on the child restraint because the buckle or latch plate is too close to the belt path opening on the restraint.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Six passenger vehicles are equipped with second row fold & tumble seats with lower anchorages that can accommodate rigid mount or flexible webbing-mounted LATCH-compatible child seats. The third row seating positions are not equipped with lower anchorages. However, the third row driver side seating position is equipped with a tether anchor.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 Five passenger vehicles are equipped with a second row bench seat only. The two outboard seating positions have lower anchorages that can accommodate rigid mount or flexible webbing-mounted LATCH-compatible child seats. The center seating position of the bench seat can also accommodate a flexible webbing-mounted LATCHcompatible child seat by using the inboard lower anchors of the two outboard seating positions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE convenient. When using the LATCH System, always follow the child restraint manufacturer’s installation instructions. NOTE: If your child restraint seat is not LATCH compatible, install the restraint using the vehicle seat belts. Tether Anchors There are tether strap anchorages behind all second row seating positions and for six passenger vehicles on the driver’s side third row seating position. The tether anchors are located in the rear surface of the seat.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 When the tether anchorage is used in the center second row bench seating position or on the third row seating position, where equipped, the strap should be positioned straight over the top of the seatback. When the tether anchorage is used in the third row seating position, the strap should be positioned straight over the top of the seatback.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor positions directly behind the child seat to secure a child restraint top tether strap. Automatic-Locking Retractor (ALR) The center seating position on vehicles equipped with a second row bench seat is equipped with an AutomaticLocking Retractor (ALR).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77 anchorages. Then tighten all three straps as you push the child restraint rearward and downward into the seat. Child restraint systems having attachments designed to connect to the lower anchorages are now available. Child restraints having tether straps and hooks for connection to the seatback tether anchorage have been available for some time. In fact, many child restraint manufacturer’s will provide add-on tether strap kits for some of their older products.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Check belt fit periodically. A child’s squirming or slouching can move the belt out of position. Improper installation of a child restraint to the LATCH anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 79 ENGINE BREAK-IN RECOMMENDATIONS A long break-in period is not required for the engine in your new vehicle. Drive moderately during the first 300 miles (500 km). After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable. While cruising, brief full-throttle acceleration, within the limits of local traffic laws, contributes to a good break-in. Wide open throttle acceleration in low gear can be detrimental and should be avoided.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If it is necessary to sit in a parked vehicle with the engine running, adjust your heating or cooling controls to force outside air into the vehicle. Set the blower at high speed. WARNING! If you are required to drive with the deck lid/liftgate open, make sure that all windows are closed, and the climate control blower switch is set at high speed. DO NOT use the recirculation mode.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 81 Periodic Safety Checks You Should Make Outside The Vehicle Tires Examine tires for excessive tread wear or uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread. Inspect tread and sidewall for cuts or cracks. Check wheel nuts for tightness, and tires (including spare) for proper pressure. Lights Have someone observe the operation of exterior lights while you work the controls.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 3 䡵 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88 ▫ Heated Remote Control Mirrors . . . . . . . . . . . .91 ▫ Inside Day / Night Mirror . . . . . . . . . . . . . . . .88 ▫ Illuminated Vanity Mirrors . . . . . . . . . . . . . . . .91 ▫ Automatic Dimming Mirror — If Equipped . . . .88 䡵 Hands–Free Communication (UConnect™) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 䡵 Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114 ▫ Third Row Seating — If Equipped . . . . . . . . . 124 ▫ 10–Way Driver’s Power Seat — If Equipped . . 114 ▫ Load Floor — If Equipped . . . . . . . . . . . . . . . 125 ▫ 8–Way Driver’s Power Seat — If Equipped . . . 115 ▫ Plastic Grocery Bag Retainer . . . . . . . . . . . . . 126 ▫ 4–Way Passenger’s Power Seat . . . . . . . . . . . . 115 䡵 Driver Memory Seat — If Equipped . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85 ▫ Headlights, Parking Lights, Instrument Panel Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135 ▫ Automatic Headlights . . . . . . . . . . . . . . . . . . 136 ▫ Daytime Running Lights (Canada Only) . . . . . 136 ▫ Lights-On Reminder . . . . . . . . . . . . . . . . . . . 136 ▫ Windshield Wiper Operation . . . . . . . . . . . . . 139 ▫ Intermittent Wiper System . . . . . . . . . . . . . . . 139 ▫ Rear Window Wiper/Washer . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ To Resume Speed . . . . . . . . . . . . . . . . . . . . . 151 ▫ Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160 ▫ To Vary The Speed Setting . . . . . . . . . . . . . . . 151 䡵 Power Sunroof — If Equipped . . . . . . . . . . . . . 160 ▫ To Accelerate For Passing . . . . . . . . . . . . . . . 152 ▫ Express Open Feature . . . . . . . . . . . . . . . . . . 161 䡵 Overhead Console — If Equipped . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 䡵 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166 ▫ Cargo Tie-Down Hooks . . . . . . . . . . . . . . . . . 168 ▫ Console Features . . . . . . . . . . . . . . . . . . . . . . 166 䡵 Roof Luggage Rack — If Equipped . . . . . . . . . . 169 ▫ Rear Cargo Storage Bin — If Equipped . . . . . . 166 䡵 Load Leveling System . . . . . . . . . . . . . . . . . . . 172 ▫ Retractable Cargo Area Cover — If Equipped . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Day / Night Mirror Adjust the mirror to center on the view through the rear window. A two point pivot system allows for horizontal and vertical adjustment of the mirror. MANUAL REARVIEW MIRROR Annoying headlight glare can be reduced by moving the small control under the mirror to the night position (toward rear of vehicle). The mirror should be adjusted while set in the day position (toward windshield).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 Driver’s Side Outside Mirror Auto Dimmer — If Equipped This mirror automatically adjusts for annoying headlight glare from vehicles behind you. You can turn this feature on or off by pressing the button at the base of the Rearview Mirror. Exterior Mirrors Folding Feature All exterior mirrors are hinged and may be moved either forward or rearward to resist damage. The hinges have three detent positions; full forward, full rearward, and normal.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Outside Mirror — Passenger’s Side Adjust the convex outside mirror so you can just see the side of your vehicle in the portion of the mirror closest to the vehicle. This type of mirror will give a much wider view to the rear, and especially of the lane next to your vehicle. Power Remote-Control Mirrors Use the mirror select switch, located on the driver’s door trim panel above the power window switches, to adjust the view obtained in the outside mirrors.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91 Press the rocker switch to the L or R for Left or Right mirror selection. Use the center off position to guard against accidentally moving a mirror position. Sun Visor Extension The sun visors may be pulled out to provide extended coverage of the side glass. Select a mirror and press one of the four arrows for the direction you want the mirror to move.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE UConnect™ allows you to transfer calls between the system and your cellular phone as you enter or exit your vehicle, and enables you to mute the system’s microphone for private conversation. The UConnect™ phonebook enables you to store up to 32 names and four numbers per name. Each language has a separate 32-name phonebook accessible only in that language. This system is driven through your Bluetooth™ Hands-Free profile cellular phone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 The UConnect™ system can be used with any HandsFree Profile certified Bluetooth™ cellular phone. See www.chrysler.com/uconnect for supported phones. If your cellular phone supports a different profile (e.g., Headset Profile), you may not be able to use any UConnect™ features. Refer to your cellular service provider or the phone manufacturer for details.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE example, you can use the combined form voice command ⬙Phonebook New Entry,⬙ or you can break the combined form command into two voice commands: ⬙Phonebook⬙ and ⬙New Entry.⬙ Please remember, the UConnect™ system works best when you talk in a normal conversational tone, as if speaking to some one sitting eight feet away from you. Voice Command Tree Refer to “Voice Tree” at the end of this section.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 NOTE: • www.chrysler.com/uconnect • www.dodge.com/uconnect • www.jeep.com/uconnect The following are general phone to UConnect™ System pairing instructions: • Press the ’Phone’ button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Setup Phone Pairing⬙ and follow the audible prompts. • When prompted, after the voice on beep, say ⬙Pair a Phone⬙ and follow the audible prompts.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Call/Dial by Saying a Number • Press the ’Phone’ button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Dial.⬙ • System will prompt you to say the number you want call. • For example, you can say ⬙234-567-8901.⬙ • The UConnect™ system will confirm the phone number and then dial. The number will appear in the display of certain radios. Call/Dial by Saying a Name • Press the “Phone” button to begin.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 • After the ⬙Ready⬙ prompt and the following beep, say ⬙Phonebook New Entry.⬙ • When prompted, say the name of the new entry. Use of long names helps the voice recognition and is recommended. For example, say ⬙Robert Smith⬙ or ⬙Robert⬙ instead of ⬙Bob.⬙ • When prompted, enter the number designation (e.g., ⬙Home,⬙ ⬙Work,⬙ ⬙Mobile,⬙ or ⬙Pager⬙). This will allow you to store multiple numbers for each phonebook entry, if desired.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • When prompted, recite the new phone number for the phonebook entry that you are editing. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Phonebook Delete.⬙ After you are finished editing an entry in the phonebook, you will be given the opportunities to edit another entry in the phonebook, call the number you just edited, or return to the main menu.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99 After confirmation, the phonebook entries will be deleted. Note that only the phonebook in the current language is deleted. Delete All Entries in the UConnect™ Phonebook • Press the ’Phone’ button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Phonebook Erase All.⬙ • The UConnect™ system will ask you to verify that you wish to delete all the entries from the phonebook. • After confirmation, the phonebook entries will be deleted.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Answer or Reject an Incoming Call - No Call Currently in Progress When you receive a call on your cellular phone, the UConnect™ system will interrupt the vehicle audio system, if on, and will ask if you would like to answer the call. To reject the call, press and hold the ’Phone’ button until you hear a single beep indicating that the incoming call was rejected.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 Toggling Between Calls If two calls are in progress (one active and one on hold), press the ’Phone’ button until you hear a single beep indicating that the active and hold status of the two calls have switched. Only one call can be placed on hold at one time.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Call Continuation Call continuation is progression of a phone call on UConnect™ system after the vehicle ignition key has been switched to off.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 Emergency Assistance If you are in an emergency and the mobile phone is reachable: The UConnect™ system does slightly lower your chances of successfully making a phone call as to that for the cell phone directly. • Pick up the phone and manually dial the emergency number for your area.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Please refer to the 24-Hour “Towing Assistance” coverage details in the Warranty information booklet and on the 24–Hour Towing Assistance Card. Paging To learn how to page, refer to ⬙Working with Automated Systems.⬙ Paging works properly except for pagers of certain companies which time-out a little too soon to work properly with the UConnect™ system. Voice Mail Calling To learn how to access your voice mail, refer to ⬙Working with Automated Systems.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 Barge In - Overriding Prompts The ’Voice Recognition’ button can be used when you wish to skip part of a prompt and issue your voice recognition command immediately. For example, if a prompt is playing ⬙Would you like to pair a phone, clear aѧ,⬙ you could press the ’Voice Recognition’ button and say ⬙Pair a Phone⬙ to select that option without having to listen to the rest of the voice prompt.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Certain brands of mobile phones do not send the dial ring to the UConnect™ system to play it on the vehicle audio system, so you will not hear it. Under this situation, after successfully dialing a number, the user may feel that the call did not go through even though the call is in progress. Once your call is answered, you will hear the audio.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 Connect or Disconnect Link Between the UConnect™ System and Cellular Phone Your cellular phone can be paired with many different electronic devices, but can only be actively ⬙connected⬙ with one electronic device at a time. If you would like to connect or disconnect the Bluetooth™ connection between a UConnect™ paired cellular phone and the UConnect™ system, then follow the instruction described in your cellular phone user’s manual.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • You can also press the ⬘Voice Recognition’ button anytime while the list is being played, and then choose the phone that you wish to select. • You can also press the ⬘Voice Recognition’ button anytime while the list is being played and then choose the phone you wish to delete. • The selected phone will be used for the next phone call.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 • low road noise, • smooth road surface, • fully closed windows, • dry weather condition. • UConnect™ phonebook nametag recognition rate is optimized for the voice of the person who stored the name in the phonebook. • You can say ⬙O⬙ (letter ⬙O⬙) for ⬙0⬙ (zero). ⬙800⬙ must be spoken ⬙eight-zero-zero.⬙ • Even though the system is designed for users speaking in North American English, French, and Spanish accents, the system may not always work for some.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • fully closed windows, and • dry weather condition. • Operation from driver seat. • Performance, such as audio clarity, echo, and loudness to a large degree rely on the phone and network, and not the UConnect™ system. • Echo at far end can sometime be reduced by lowering the in-vehicle audio volume. Bluetooth Communication Link Occasionally, Cellular phones have been found to lose connection to the UConnect™ system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE North American English Primary Alternate(s) Zero Oh Add location Add new All All of them Confirmation prompts Confirmations prompts Delete a name Delete Language Select language List names List all List paired phones List phones Pager Beeper Phone pairing Pairing Phonebook Phone book Return to main menu Return.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 WARNING! Adjust the seat only while the vehicle is parked. Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. 8–Way Driver’s Power Seat — If Equipped The driver’s power seat switches are located on the driver’s front door trim panel. The bottom switch controls up/down, forward/rearward, and tilt adjustment.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE restraint. To lower the head restraint, depress the release tab located at the base of the head restraint and push down on the head restraint. Heated Seats — If Equipped This feature heats the driver, front passenger and second row seats. The controls for the front heated seats are located on the door trim panel next to the power seat switches.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 Press the switch once to select a heat setting (high or low) and press the switch a second time in the same direction to turn the heated seat off. The indicator light will show when LOW or HIGH heat is ON. The controls for the second row heated seats are located on the center console between the seats. Press the switch once to select a heat setting (high or low) and press the switch a second time in the same direction to turn the heated seat off.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: • If the lights in the second row heated seat switch begin to flash when the switch is pressed, it indicates that the heated seat is not functioning properly and that service is required. See your authorized dealer for service. • Once a heat setting is selected, heat will be felt within 2 to 3 minutes. • The heated seats will turn off when the ignition switch is turned to the OFF position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 WARNING! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or fatally injured. Use the recliner only when the vehicle is parked. Second Row Manual Seat Adjuster — If Equipped The adjusting bar is located under the front of the seat. Pull the bar up and move the seat to the desired position. Release the bar to lock the seat into position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Adjust the seat only while the vehicle is parked. Adjusting a seat while the vehicle is moving is dangerous. The seat belt might not be properly adjusted and you could be injured. Second Row Bench Seating — If Equipped The second row seats may be used with either or both seatbacks folded forward for additional storage space. To fold the seat, remove any objects from in front of or on the seat.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 CAUTION! Be sure there is nothing in front of the second row seat cushion before folding it down. Damage to the seat may occur. 4. Pull up on the seatback release lever located on the outboard side of the seat labeled “1” and fold the seatback down. 3 Second Row Fold & Tumble Seats — If Equipped The second row seats can be folded and tumbled forward for easy access to the third seat or rear cargo area. To fold and tumble the seat, follow these steps: 1.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 5. Pull up on the release handle labeled “2” and lift firmly to tumble the seat fully forward. If the seat contacts the rear of the front seat, move the front seat forward. To relatch the seat, tilt the seat rearward and push down firmly to engage the rear attachments. Then lift the seatback release lever labeled “1” and pull the seatback up to return it to its full upright position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 To fold and tumble the seat forward, follow these steps: 1. Pull up on the seatback release handle “1” located on the back of the seat to fold the seatback down. 3 Release Strap 2 Location Release Handle 1 Location 2. Pull the release strap “2” located at the bottom of the seat to lift and tumble the seat forward. To relatch the seat, tilt the seat rearward and push down firmly to engage the rear attachments.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Third Row Seating — If Equipped The third row seats may be used with either or both seatbacks folded forward for additional storage space. To fold the seat, remove any objects from in front of or on the seat. Then pull handle located on the seatback and push it forward. WARNING! Do not sit in the 3rd row seat with the second row seatbacks folded or with the second row seats folded and tumbled.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 WARNING! • Not all head restraints in this vehicle are the same. Head restraints from one seating position should not be removed and installed in any other seating position. In a collision, serious injury or death may result if the proper head restraint is not installed on each seat. • The cargo area in the rear of the vehicle should not be used as a play area by children. They could be seriously injured in a collision.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Pull on the load floor strap and lift the panel from the driver’s second row seatback over the center console and onto the passenger second row seat. Plastic Grocery Bag Retainer Retainer hooks which will hold plastic grocery bag handles are built into the seatbacks of all front seats. The floor supports the partial weight of the bagged goods. Load Floor Panel NOTE: Be sure to reattach the strap to secure the load floor panel when not in use.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 DRIVER MEMORY SEAT — IF EQUIPPED If your vehicle is equipped with memory systems, your remote keyless entry transmitter or memory seat buttons on the driver’s door panel can be used to recall the driver’s seat, outside mirrors, adjustable pedals (if equipped) and radio station presets to saved positions. The memory seat buttons located on the driver’s door will always recall stored settings.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Your vehicle has been delivered with two remote keyless entry transmitters. One or both transmitters can be linked to either memory position. Up to eight remote keyless entry transmitters can be used with your vehicle. The memory seat system can also accommodate up to eight transmitters linked to either of the two stored seat positions or any combination of the two positions. To Program Memory Seat Buttons & RKE Transmitters, Follow These Steps: 1.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 Repeat the above steps for the second position using the other driver’s door numbered button and Remote Keyless Entry Transmitter. Each time the SET (S) button and a numbered button are pressed, you erase the old memory and store a new one. To Disable A Transmitter Link, Follow These Steps: 1. Select “Remote Linked To Memory” from the Electronic Vehicle Information Center, Customer Programmable features. 2.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Easy Exit Seat (Available with Memory Seat Only) This feature provides automatic driver’s seat positioning which will enhance driver mobility out of and into the vehicle. removed from the ignition switch. The seat will move forward to the memory/driving position when the key is placed into the ignition and turned out of the LOCK position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 Tilt Mirrors in Reverse (Available with Memory Seat Only) — If Equipped This additional feature provides automatic outside mirror positioning which will aid the driver’s view of the ground rearward of the front doors. The outside mirrors will move slightly downward from the present position when the vehicle is shifted into the Reverse position. The outside mirrors will then return to the original position when the vehicle is shifted out of Reverse position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Next, push to the left the safety catch located under the front edge of the hood, near the center. To prevent possible damage, do not slam the hood to close it. Lower the hood until it is open approximately 15 cm (6 inches) and then drop it. This should secure both latches. Never drive your vehicle unless the hood is fully closed, with both latches engaged.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 LIGHTS Overhead Console Map/Reading Lights These lights are mounted between the sun visors on the overhead console. Each light is turned ON by pressing the lens. Press the lens a second time to turn the light OFF. The lights also turn on when a door is opened or the dimmer control is turned fully upward, past the second detent.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Interior Lights The interior lights come on when a door is opened. The interior lights will automatically turn off in about 15 minutes if a door is left open or the dimmer control is left in the Dome light position. Turn the ignition switch ON to restore the interior light operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 Headlights, Parking Lights, Instrument Panel Lights Turn the end of the Multi-Function Lever to the first detent for parking light and instrument panel light operation. Turn to the second detent for headlight, park light and instrument panel light operation. Dome Light Position Rotate the dimmer control completely upward to the second detent to turn on the interior lights. The interior lights will remain on when the dimmer control is in this position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Parade Mode (Daytime Brightness Feature) Rotate the dimmer control upward to the first detent. This feature brightens the odometer and radio display when the parking lights or headlights are on during daylight conditions. Automatic Headlights This system automatically turns your headlights ON or OFF based on ambient light levels. To turn the system ON, turn the end of the Multi-Function Lever to the third detent position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 To activate the delay feature, turn off the ignition switch while the headlights are still on. Then turn off the headlights within 45 seconds. The 90 second delay interval begins when headlight switch is turned off. If the headlights or park lights are turned back on or the ignition switch is turned on, the delay will be cancelled. If the headlights are turned off before the ignition, they will turn off in the normal manner.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Highbeam/Lowbeam Select Switch Pull the Multi-Function Lever towards you to switch the headlights to HIGH beam. Pull the Lever a second time to switch the headlights to LOW beam. Passing Light You can signal another vehicle with your headlights by lightly pulling the Multi-Function Lever toward you. This will cause the headlights to turn on at high beam and remain on until the lever is released.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 If the lever is pulled while in the OFF position, the wipers will operate for two wipe cycles, then turn OFF. Mist Feature Push down on the wiper lever to activate a single wipe to clear off road mist or spray from a passing vehicle. As long as the lever is held down, the wipers will continue to operate. select the desired delay interval. The delay can be regulated from a maximum of approximately 23 seconds between cycles, to a cycle every second.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rotating the center of the switch up to the DEL (Delay) position or the ON position will activate the rear wiper. Push the lever forward to initiate the rear wash function in any of the three positions. The washer pump will continue to operate as long as the lever is pressed. Upon release, the rear wiper will cycle two times before returning to the set position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 TILT STEERING COLUMN To tilt the column, pull the lever, located behind the turn signal control, toward you and move the steering wheel up or down, as desired. Release the lever to lock the steering wheel firmly in place. WARNING! Tilting the steering column while the vehicle is moving is dangerous. Without a stable steering column, you could lose control of the vehicle and have an accident. Adjust the column only while the vehicle is stopped.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE spinning faster than the other, the system will apply the brake of the spinning wheel. This will allow more engine torque to be applied to the wheel that is not spinning. This feature remains active even if TCS and ESP are in either the “Partial Off” or “ESP Off” modes. The ESP / TCS Indicator Lamp, located in the instrument cluster, will light up when the Traction Control is in use.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 NOTE: • The Traction Control Indicator comes on each time the ignition switch is turned ON. This will occur even if you used the switch to turn the system OFF. • The Traction Control system will make buzzing or clicking sounds when in operation. REAR PARK ASSIST SYSTEM — IF EQUIPPED This system is used to help drivers determine if an obstacle is in the way of the vehicle while it is backing up in addition to the use of inside rearview and outside mirrors.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE The system dimly illuminates the two outer most yellow LEDs when it is ON and detecting no obstacles. The following chart shows the warning display operation when the system is detecting an obstacle: WARNING DISPLAY DISTANCES DISPLAY LED 1st LED 2nd LED 3rd LED 4th LED 5th LED 6th LED 7th LED 8th LED OBSTACLE DISTANCE FROM: REAR CORNERS REAR CENTER 59 in. (150 cm) 47 in. (120 cm) 39 in. (100 cm) 31.5 in. (80 cm) 31.5 in. (80 cm) 25.5 in. (65 cm) 25.5 in.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 WARNING! CAUTION! • Drivers must be careful when backing up even when • To avoid vehicle damage the Rear Park Assist System should only be used as a parking aid and is unable to recognize every obstacle, including small objects. Parking curbs might be temporarily detected or not detected at all. Obstacles located above or below the sensors will not be detected when they are in close proximity to the rear of the vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: • Ensure that the rear bumper is free of dirt and debris to keep the system operating properly. • Jackhammers, large trucks, and other vibrations could affect the performance of the system. If “Service Park Assist System” appears in the Electronic Vehicle Information Center (EVIC) after making sure the rear bumper is clean please see your authorized dealer.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 WARNING! CAUTION! Drivers must be careful when backing up even when using the Rear Camera System. Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, obstructions, or blind spots before backing up. You are responsible for the safety of your surroundings and must continue to pay attention while backing up. Failure to do so can result in serious injury or death.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ADJUSTABLE PEDALS — IF EQUIPPED This feature allows both the brake and accelerator pedals to move toward or away from the driver to provide improved position with the steering wheel. The adjustable pedal system is designed to allow a greater range of driver comfort for steering wheel tilt and seat position. The switch is located on the drivers door trim panel next to the power seat switches.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 Press the switch rearward to move the pedals rearward (toward the driver). • The pedals can be adjusted with the ignition OFF. • The pedals can be adjusted while driving. • The pedals cannot be adjusted when the vehicle is in R (Reverse) or when the Speed Control is ON.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ELECTRONIC SPEED CONTROL When engaged, this device takes over the accelerator operation at speeds greater than 30 mph (50 km/h). The speed control switches are located on the steering wheel. To Activate: Push the “ON/OFF” button once and the CRUISE indicator located near the instrument cluster odometer will illuminate showing the electronic speed control system is on.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 To Set At A Desired Speed: When the vehicle has reached the desired speed, press and release the “SET” button. Release the accelerator and the vehicle will operate at the selected speed. The CRUISE SET indicator located near the instrument cluster odometer will illuminate showing the electronic speed control is set. NOTE: While in the AutoStick mode, Speed Control will only function in third or fourth gear.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Tapping the “COAST” button once will result in a 1 mph (2 km/h) speed decrease. Each time the button is tapped, speed decreases. On steep hills a greater speed loss or gain may occur so it may be preferable to drive without speed control. To Accelerate For Passing: Depress the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. WARNING! NOTE: The speed control system maintains speed up and down hills.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 OVERHEAD CONSOLE — IF EQUIPPED The overhead console can contain courtesy/reading lights, an optional universal garage door opener (HomeLink威), storage for sunglasses, optional power sunroof switches and an optional power liftgate switch. Courtesy/Reading Lights At the forward end of the console are two courtesy/ reading lights. Press the lens to turn these lights on. Press a second time to turn the lights off.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE GARAGE DOOR OPENER — IF EQUIPPED The HomeLink威 Universal Transceiver replaces up to three remote controls (hand held transmitters) that operate devices such as garage door openers, motorized gates, or home lighting. It triggers these devices at the push of a button. The Universal Transceiver operates off your vehicle’s battery and charging system; no batteries are needed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 WARNING! Vehicle exhaust contains carbon monoxide, a dangerous gas. Do not run the vehicle’s exhaust while training the transceiver. Exhaust gas can cause serious injury or death. WARNING! Your motorized door or gate will open and close while you are training the Universal Transceiver. Do not train the transceiver if people or pets are in the path of the door or gate.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE seconds and do not repeat Step One to program a second and/or third hand-held transmitter to the remaining two HomeLink buttons. 3. Simultaneously press and hold both the HomeLink button that you want to train and the hand-held transmitter buttons. Do not release the buttons until Step Four has been completed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 5. Press and hold the just trained HomeLink button and observe the indicator light or the EVIC display. If the indicator light stays on constantly, programming is complete and your device should activate when the HomeLink button is pressed and released. If the EVIC display shows “Channel X Transmit” (where X is Channel 1, 2, or 3), programming is complete and your device should activate when the HomeLink button is pressed and released. (rolling code system).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Return to the vehicle and firmly press, hold for two seconds and release the programmed HomeLink button. Repeat the ⴖpress/hold/releaseⴖ sequence a second time, and, depending on the brand of the garage door opener (or other rolling code equipped device), repeat this sequence a third time to complete the programming. HomeLink should now activate your rolling code equipped device.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 Using HomeLink To operate, simply press and release the programmed HomeLink button. Activation will now occur for the trained device (i.e. garage door opener, gate operator, security system, entry door lock, home/office lighting, etc.). For convenience, the hand-held transmitter of the device may also be used at any time. In the event that there are still programming difficulties or questions, contact HomeLink at: www.homelink.com or 1-800-3553515.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Security If you sell your vehicle, be sure to erase the frequencies by following the “Erasing HomeLink Buttons” instructions in this section. This device complies with part 15 of FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following conditions: In the event that you are still having programming difficulties, questions, or comments, contact HomeLink at: www.homelink.com or 1-800-355-3515.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 Press and hold the “OPEN” button rearward to fully open the sunroof. The sunroof can be stopped at any position between closed and full open. Momentarily pressing the “OPEN” button rearward will activate the Express Open Feature, causing the sunroof to open automatically. Press and hold the “VENT” button to open the vent. The sunroof can be stopped at any position between closed and full vent.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To close the sunroof, press and hold the “CLOSE” button forward. Again, any release of the button will stop the movement and the sunroof will remain in a partial open condition until the button is pushed forward again. The sunshade can be opened manually. It will also open as the sunroof opens. The sunshade cannot be closed if the sunroof is open. WARNING! • NEVER leave children alone in a vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occurrence and can be minimized. If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE A third outlet is located on the back of the front center console near the floor, and is also controlled by the ignition switch. A fourth outlet is located on the driver’s side, in the rear cargo area and is also controlled by the ignition switch. The outlets include tethered caps labeled with a key or battery symbol indicating the power source.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 CUPHOLDERS Front Seat Cupholders The cupholders are located in the forward edge of the center console. Push down on the forward edge of the console to release the cupholders. Press the cover up when the cupholders are no longer needed. Six Passenger Seating Cupholders Second Row Seat Cupholders On vehicles equipped with five passenger seating the second row seat cupholders are located in middle of the seatback armrest.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE On vehicles equipped with six passenger seating the second row seat cupholders are located in the forward edge of the center console located between the second row seats. Push down on the forward edge of the console to release the cupholders. Press the cover up when the cupholders are no longer needed. Rear Cargo Storage Bin — If Equipped The storage bin is located in the floor of the rear cargo area. To open lift up on the handle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 Retractable Cargo Area Cover — If Equipped To cover the cargo area: 1. Fold down the third row seatbacks. 2. Unfold the cargo cover extensions and lock into place. 3. Insert the pins on the ends of the cover into the slots located on the trim panel behind the second row seatbacks. 4. Grasp the center portion of the cover flap. Pull it over the cargo area. 5. Insert the pins on the ends of the cover flap into the slots on the rear trim panel. 6.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Insert the pins on the ends of the cover into the slots located on the trim panel behind the third row seatbacks. 4. Grasp the center portion of the cover flap. Pull it over the cargo area. 5. Insert the pins on the ends of the cover flap into the slots on the rear trim panel. 6. The liftgate may be opened or closed with the cargo cover in place.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 • Place as much cargo as possible in front of the rear axle. Too much weight or improperly placed weight over or behind the rear axle can cause the rear of the vehicle to sway. • Do not pile luggage or cargo higher than the top of the seatback. This could impair visibility or become a dangerous projectile in a sudden stop or collision.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Distribute cargo weight evenly on the roof rack crossbars. The roof rack does not increase the total load carrying capacity of the vehicle. Be sure the total load of cargo inside the vehicle plus that on the external rack does not exceed the maximum vehicle load capacity. To move the cross bars, press the upper edge of each cross bar button, then move the cross bar to the desired position, keeping the crossbars parallel to the rack frame.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 CAUTION! WARNING! • Crossbars should remain equally spaced or parallel at Cargo must be securely tied before driving your vehicle. Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage. Follow the Roof Rack Cautions when carrying cargo on your roof rack. any luggage rack position for proper function. Noncompliance could result in damage to the luggage rack, cargo and/or vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE LOAD LEVELING SYSTEM The automatic load leveling system will provide a level riding vehicle under most passenger and cargo loading conditions. A hydraulic pump contained within the shock absorbers raises the rear of the vehicle to the correct height. It takes approximately 1 mile (1.6 km) of driving for the leveling to complete depending on road surface conditions.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 Instrument Panel And Controls . . . . . . . . . . . . . 177 䡵 Setting The Analog Clock . . . . . . . . . . . . . . . . . 199 䡵 Base Instrument Cluster . . . . . . . . . . . . . . . . . . 178 䡵 Electronic Digital Clock . . . . . . . . . . . . . . . . . . 200 䡵 Premium Instrument Cluster . . . . . . . . . . . . . . . 179 ▫ Clock Setting Procedure . . . . . . . . . . . . . . . . . 200 䡵 Instrument Cluster Descriptions . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 䡵 Sales Code RAH—AM & FM Stereo Radio With CD Player And CD/DVD Changer Controls . . . . 202 ▫ Operation Instructions - (CD Mode For MP3 Audio Play) . . . . . . . . . . . . . . . . . . . . . . . . . 220 ▫ Radio Operation . . . . . . . . . . . . . . . . . . . . . . 202 䡵 6 Disc CD/DVD Changer (RDV) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . 221 ▫ CD Player Operation . . . . . . . . . . . . . . . . . . . 206 ▫ CD/DVD Changer Operation . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 175 䡵 Satellite Radio — If Equipped . . . . . . . . . . . . . . 233 ▫ Satellite Antenna . . . . . . . . . . . . . . . . . . . . . . 237 ▫ System Activation . . . . . . . . . . . . . . . . . . . . . 234 ▫ Reception Quality . . . . . . . . . . . . . . . . . . . . . 237 ▫ Electronic Serial Number/Sirius Identification Number (ENS/SID) . . . . . . . . . . . . . . . . . . . . 234 䡵 Remote Sound System Controls . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Manual Air Conditioning Operation . . . . . . . . 246 ▫ Dual-Zone Automatic Temperature Control . . . 249 ▫ Electric Rear Window Defroster . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 177 INSTRUMENT PANEL AND CONTROLS 4
UNDERSTANDING YOUR INSTRUMENT PANEL BASE INSTRUMENT CLUSTER
UNDERSTANDING YOUR INSTRUMENT PANEL 179 PREMIUM INSTRUMENT CLUSTER 4
UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTIONS 1. Voltage Light This light monitors the electrical system voltage. The light should turn on momentarily as the engine is started. If the light stays on or turns on while driving, it indicates a problem with the charging system. Immediate service should be obtained. 2. Temperature Gauge The temperature gauge shows engine coolant temperature.
UNDERSTANDING YOUR INSTRUMENT PANEL 181 WARNING! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call a service center if your vehicle overheats. If you decide to look under the hood yourself, see Section 7 of this manual. Follow the warnings under the Cooling System Pressure Cap paragraph. 3. Fuel Gauge The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON position.
UNDERSTANDING YOUR INSTRUMENT PANEL is not functioning and that service is required. However, the conventional brake system will continue to operate normally if the BRAKE warning light is not on. indicated by the Brake Warning Light which will turn on when the brake fluid level in the master cylinder has dropped below a specified level. If the ABS light is on, the brake system should be serviced as soon as possible to restore the benefits of Anti-Lock brakes.
UNDERSTANDING YOUR INSTRUMENT PANEL 183 Vehicles equipped with Anti-Lock brakes (ABS), are also equipped with Electronic Brake Force Distribution (EBD). In the event of an EBD failure, the Brake Warning Light will turn on along with the ABS Light. Immediate repair to the ABS system is required. The operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON position. The light should illuminate for approximately two seconds.
UNDERSTANDING YOUR INSTRUMENT PANEL disabled for about 4 minutes until the brakes have cooled. The system will automatically reactivate and turn off the Traction Control Light. 12. AutoStick Light This display indicator illuminates when the gearshift lever is moved to the AutoStick position. 9. Tachometer The red segments indicate the maximum permissible engine revolutions-per-minute (rpm. x 1000) for each gear range. Before reaching the red area, ease up on the accelerator. 13.
UNDERSTANDING YOUR INSTRUMENT PANEL 185 Loose Fuel Filler Cap If the vehicle diagnostic system determines that the fuel filler cap is loose, improperly installed, or damaged, GASCAP will be displayed in the instrument cluster odometer. Tighten the fuel filler cap properly and press the odometer reset button to turn the GASCAP message off. If the problem continues, the message will appear the next time the vehicle is started. See Section 7 of this manual for more information. start.
UNDERSTANDING YOUR INSTRUMENT PANEL 17. Navigation Screen / Rear View Camera — If Equipped The navigation system provides maps, turn identification, selection menus and instructions for selecting a variety of destinations and routes. Refer to your “Navigation User’s Manual” for detailed operating instructions. The Rear View Camera system uses the Navigator Screen to display the area behind the vehicle. Camera view will display only while the vehicle is in R (Reverse). 18.
UNDERSTANDING YOUR INSTRUMENT PANEL 187 21. Tire Pressure Monitoring Telltale Lamp — If Equipped Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label.
UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! The Tire Pressure Monitoring System (TPMS) has been optimized for the original equipment tires and wheels. TPMS pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equipment that is not of the same size, type, and / or style. Aftermarket wheels can cause sensor damage.
UNDERSTANDING YOUR INSTRUMENT PANEL 189 25. Liftgate Ajar — If Equipped This light turns on if the liftgate is not completely closed. 26. Door Ajar Light — If Equipped This light turns on if a door is not completely closed. 27. Washer Fluid Light — If Equipped This light turns on when the washer fluid level falls below approximately 1/4 filled. The light will remain on until fluid is added. 28.
UNDERSTANDING YOUR INSTRUMENT PANEL — The ESP Control System will make buzzing or clicking sounds when it is active. This is normal; the sounds will stop when ESP becomes inactive following the maneuver that caused the ESP activation. 29. Electronic Throttle Control (ETC.) Light This light informs you of a problem with the Electronic Throttle Control system. If a problem is detected the light will come on while the engine is running.
UNDERSTANDING YOUR INSTRUMENT PANEL 191 ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) — IF EQUIPPED The Electronic Vehicle Information Center (EVIC) consists of the following: • Vehicle information warning message displays • Tire Pressure Monitor System — If Equipped • Customer programmable features • Compass display • Mini-Trip functions Pressing the MENU button will change the displayed programming features. Pressing the STEP button will display the available choices.
UNDERSTANDING YOUR INSTRUMENT PANEL • SET INHIBITED DUE TO MOTION (with a single chime) • FOB LINKED (with a single chime) • FOB UNLINKED (with a single chime) • PARK BRAKE ENGAGED (with a single chime) • LOW BRAKE FLUID (with a single chime) • LOW FUEL (with a single chime) • LEFT/RIGHT FRONT DOOR AJAR (one or more, with a single chime if speed is above 1 mph) • LEFT/RIGHT REAR DOOR AJAR (one or more, with a single chime if speed is above 1 mph) • DOOR(S) AJAR (with a single chime) • DOOR(S) AND GATE
UNDERSTANDING YOUR INSTRUMENT PANEL 193 • CLEARING CHANNELS • CHANNELS CLEARED • CHANNELS DEFAULTED • DID NOT TRAIN • 1,2,3 OR 4 TIRE(S) LOW PRESSURE (Refer to ”Tire Pressure Monitor System” in the “Starting And Operating, Tire Section”) • CHECK TPM SYSTEM (Refer to ”Tire Pressure Monitor System” in the “Starting And Operating, Tire Section”) • TCS SUSPENDED (Traction Control System, with a graphic and single chime) • TCS ACTIVE (Traction Control System, with a graphic) • SERVICE TCS SYSTEM (Traction Contr
UNDERSTANDING YOUR INSTRUMENT PANEL Display U.S. or Metric? Pressing the US/M button will change the EVIC, odometer, navigation system and A/C Control units from US to Metric. Use factory Settings? When in this display you may select to use the factory settings and no programmable features will be offered. Auto Door Locks? When this feature is selected, all doors and the liftgate lock automatically when the speed of the vehicle reaches 15 mph (25 km/h).
UNDERSTANDING YOUR INSTRUMENT PANEL 195 Sound Horn On Lock? When this feature is selected a short horn sound will occur when the remote keyless entry “Lock” button is pressed. This feature may be selected with or without the flash lights on lock/unlock feature. Pressing the STEP button when in this display will select “Yes” or “No.
UNDERSTANDING YOUR INSTRUMENT PANEL Reset Service Distance (Displays Only if Service Interval was Changed) When this feature is selected the current accumulated service distance can be reset to the newly selected service interval. Pressing the STEP button when in this display will select “Yes” or “No.
UNDERSTANDING YOUR INSTRUMENT PANEL 197 Compass Display — If Equipped This display provides one of eight compass readings to indicate the direction the vehicle is facing. Automatic Compass Calibration This compass is self calibrating which eliminates the need to manually set the compass. When the vehicle is new, the compass may appear erratic and the EVIC will display “COMPASS CALIBRATING” until the compass is calibrated.
UNDERSTANDING YOUR INSTRUMENT PANEL Compass Variance Compass Variance is the difference between magnetic North and Geographic North. In some areas of the country, the difference between magnetic and geographic North is great enough to cause the compass to give false readings. If this occurs, the compass variance must be set. NOTE: Magnetic materials should be kept away from the overhead console.
UNDERSTANDING YOUR INSTRUMENT PANEL 199 To set the variance: Turn the ignition switch ON and set the display to Compass. Press the MENU button for approximately 5 seconds but no more than 10 seconds. The “COMPASS VARIANCE” message and the last variance zone number will be displayed. Press the STEP button to select the proper variance zone as shown in the map. Press the RESET button to set the new variance zone and resume normal operation.
UNDERSTANDING YOUR INSTRUMENT PANEL ELECTRONIC DIGITAL CLOCK RADIO GENERAL INFORMATION The clock and radio each use the display panel built into the radio. A digital readout shows the time in hours and minutes whenever the ignition switch is in the ON or ACC position and the time button is pressed. Radio Broadcast Signals Your new radio will provide excellent reception under most operating conditions.
UNDERSTANDING YOUR INSTRUMENT PANEL 201 Electrical Disturbances Radio waves may pick up electrical disturbances during transmission. They mainly affect the wave amplitude, and thus remain a part of the AM reception. They interfere very little with the frequency variations that carry the FM signal. AM Reception AM sound is based on wave amplitude, so AM reception can be disrupted by such things as lightning, power lines and neon signs.
UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE RAH—AM & FM STEREO RADIO WITH CD PLAYER AND CD/DVD CHANGER CONTROLS NOTE: The radio sales code is located on the lower left side of your radio faceplate. Radio Operation Power/Volume Control Press the ON/VOL control to turn the radio on. Turn the volume control clockwise to increase the volume. NOTE: Power to operate the radio is supplied through the ignition switch. It must be in the ON or ACC position to operate the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL 203 Toggle the TUNE button to select the following format types: Program Type Adult Hits Classical Classic Rock College Country Information Jazz Foreign Language News Nostalgia Oldies Personality Public Rhythm and Blues Radio Display Adult Hit Classical Classic Rock College Country Inform Jazz Language News Nostalgia Oldies Personality Public R&B Program Type Religious Music Religious Talk Rock Soft Soft Rock Soft Rhythm and Blues Sports Talk Top 40 Weather Radio Disp
UNDERSTANDING YOUR INSTRUMENT PANEL The radio display will flash “SEEK” and the selected PTY program type when searching for the next PTY station. If no station is found with the selected PTY program type, the radio will return to the last preset station. top of the button to seek up and the bottom to seek down. The radio will remain tuned to the new station until you make another selection. Holding the button in will bypass stations without stopping until you release it.
UNDERSTANDING YOUR INSTRUMENT PANEL 205 Tone Control The Bass and/or Treble controls sound for the desired tone. Press the AUDIO button, select Bass or TREBLE, then press SEEK + or SEEK ⫺ to increase or decrease amplification of the band. To Set The Radio Push-Button Memory When you are receiving a station that you wish to commit to push-button memory, press the SET button. SET 1 will show in the display window. Select the push-button you wish to lock onto this station and press and release that button.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Changes or modifications not expressively approved by the party responsible for compliance could void the user’s authority to operate the equipment. Inserting The Compact Disc CAUTION! CD Player Operation NOTE: • The ignition switch must be in the ON or ACC position and the volume control ON before the CD player will operate.
UNDERSTANDING YOUR INSTRUMENT PANEL 207 Seek Press the top of the SEEK button for the next selection on the CD. Press the bottom of the button to return to the beginning of the current selection, or return to the beginning of the previous selection if the CD is within the first 10 seconds of the current selection. EJT — Eject Press the EJT button and the disc will unload and move to the entrance for easy removal. The unit will switch to the radio mode.
UNDERSTANDING YOUR INSTRUMENT PANEL CD/DVD Changer Operation Press the MODE button to select between the CD player and the optional remote CD/DVD changer. Time Press the TIME button to change the display from elapsed CD or DVD playing time to time of day. Notes On Playing MP3 Files The radio can play MP3 files, however, acceptable MP3 file recording media and formats are limited. When writing MP3 files, pay attention to the following restrictions.
UNDERSTANDING YOUR INSTRUMENT PANEL 209 CD audio tracks and computer files (including MP3 files). Discs created with an option such as ⬙keep disc open after writing⬙ are most likely multisession discs. The use of multisession for CD audio or MP3 playback may result in longer disc loading times. Supported MP3 file formats The radio will recognize only files with the *.mp3 extension as MP3 files. Non-MP3 files named with the *.mp3 extension may cause playback problems.
UNDERSTANDING YOUR INSTRUMENT PANEL Playback of MP3 files When a medium containing MP3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3 files.
UNDERSTANDING YOUR INSTRUMENT PANEL 211 RW/FF (CD Mode For MP3 Play) Press the FF side of the button to move forward through the MP3 selection. Press the RW side of the button to move back through the MP3 selection. Operating Instructions - Hands Free Phone (If Equipped) Refer to Hands Free Phone section of the Owner’s Manual. AM/FM Button (CD Mode For MP3 Play) Switches back to Radio mode.
UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE REV AM & FM STEREO RADIO WITH CD PLAYER AND CD/DVD CHANGER CONTROLS NOTE: The radio sales code is located on the lower left side of your radio faceplate. Radio Operation Power/Volume Control Press the ON/VOL control to turn the radio on. Turn the volume control clockwise to increase the volume. NOTE: Power to operate the radio is supplied through the ignition switch. It must be in the ON or ACC position to operate the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL 213 Toggle the TUNE button to select the following format types: Program Type Adult Hits Classical Classic Rock College Country Information Jazz Foreign Language News Nostalgia Oldies Personality Public Rhythm and Blues Radio Display Adult Hit Classical Classic Rock College Country Inform Jazz Language News Nostalgia Oldies Personality Public R&B Program Type Religious Music Religious Talk Rock Soft Soft Rock Soft Rhythm and Blues Sports Talk Top 40 Weather Radio Disp
UNDERSTANDING YOUR INSTRUMENT PANEL The radio display will flash “SEEK” and the selected PTY program type when searching for the next PTY station. If no station is found with the selected PTY program type, the radio will return to the last preset station. top of the button to seek up and the bottom to seek down. The radio will remain tuned to the new station until you make another selection. Holding the button in will bypass stations without stopping until you release it.
UNDERSTANDING YOUR INSTRUMENT PANEL 215 Tone Control The Bass and/or Treble controls sound for the desired tone. Press the AUDIO button, select Bass or TREBLE, then press SEEK + or SEEK ⫺ to increase or decrease amplification of the band. To Set The Radio Push-Button Memory When you are receiving a station that you wish to commit to push-button memory, press the SET button. SET 1 will show in the display window. Select the push-button you wish to lock onto this station and press and release that button.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Changes or modifications not expressively approved by the party responsible for compliance could void the user’s authority to operate the equipment. Inserting The Compact Disc CAUTION! CD Player Operation NOTE: • The ignition switch must be in the ON or ACC position and the volume control ON before the CD player will operate.
UNDERSTANDING YOUR INSTRUMENT PANEL 217 Seek Press the top of the SEEK button for the next selection on the CD. Press the bottom of the button to return to the beginning of the current selection, or return to the beginning of the previous selection if the CD is within the first 10 seconds of the current selection. EJT — Eject Press the EJT button and the disc will unload and move to the entrance for easy removal. The unit will switch to the radio mode.
UNDERSTANDING YOUR INSTRUMENT PANEL CD/DVD Changer Operation Press the MODE button to select between the CD player and the optional remote CD/DVD changer. Time Press the TIME button to change the display from elapsed CD or DVD playing time to time of day. Notes On Playing MP3 Files The radio can play MP3 files, however, acceptable MP3 file recording media and formats are limited. When writing MP3 files, pay attention to the following restrictions.
UNDERSTANDING YOUR INSTRUMENT PANEL 219 CD audio tracks and computer files (including MP3 files). Discs created with an option such as ⬙keep disc open after writing⬙ are most likely multisession discs. The use of multisession for CD audio or MP3 playback may result in longer disc loading times. Supported MP3 file formats The radio will recognize only files with the *.mp3 extension as MP3 files. Non-MP3 files named with the *.mp3 extension may cause playback problems.
UNDERSTANDING YOUR INSTRUMENT PANEL Playback of MP3 files When a medium containing MP3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3 files.
UNDERSTANDING YOUR INSTRUMENT PANEL 221 RW/FF (CD Mode For MP3 Play) Press the FF side of the button to move forward through the MP3 selection. Press the RW side of the button to move back through the MP3 selection. Operating Instructions - Satellite Radio Mode (If Equipped) Refer to the Satellite Radio section of the Owner’s Manual. AM/FM Button (CD Mode For MP3 Play) Switches back to Radio mode.
UNDERSTANDING YOUR INSTRUMENT PANEL The CD/DVD Changer will play CD-R, CD-RW, CDAudio and DVD Video disc formats. The video screen will turn on automatically once a DVD is inserted into the changer. NOTE: The ignition switch must be in the ON or ACC position before the CD/DVD changer will operate. Operating Instructions — CD/DVD Changer Loading The CD/DVD Changer The premium version has a multi-disc changer, and will accept up to six discs.
UNDERSTANDING YOUR INSTRUMENT PANEL 223 which numbered position the disc will be loaded into. The disc will automatically be pulled into the CD/DVD changer. 3. Upon insertion, the disc will begin to play, and the light below the loading slot will turn off. On vehicles equipped with the premium version the light above the chosen button will remain illuminated. 4. Repeat the process for loading any additional CD/ DVDs into the premium version multi-disc changer.
UNDERSTANDING YOUR INSTRUMENT PANEL EJECT (EJT) Button If there is a disc in the changer, press the EJT button and the disc will eject. If you do not remove the disc within 10 seconds, it will be reloaded and the display will show PAUSE. The radio mode will continue to operate. To eject additional discs from the premium version multi-disc changer, first select the numbered button where the disc is located and then press the EJT button.
UNDERSTANDING YOUR INSTRUMENT PANEL 225 Remote Control Buttons 1. Headphone Transmitter 2. Menu Up/Next Track/Chapter 3. Menu Left/Fast Rewind 4. Return 5. Setup 6. Pause/Play 7. Mute 8. Display 9. Mode 10. Program Down - Previous Disc 11. Program Up - Next Disc 12. Slow 13. Stop 14. Menu 15. Menu Down/Previous Track/Chapter 16. Menu Right/Fast Forward Remote Control Buttons 17. Enter 18.
UNDERSTANDING YOUR INSTRUMENT PANEL RTN Button (4) This button only functions in CD/DVD mode. Press this button to return to the previous menu when in the disc menu mode. PAUSE/PLAY Button (6) This button only functions in DVD video mode. Press this button once to pause the video, press a second time to play the video. SETUP Button (5) This button only functions in CD/DVD mode. Press the button after pressing the STOP button to access the set up menu.
UNDERSTANDING YOUR INSTRUMENT PANEL 227 SLOW Button (12) This button only functions in DVD video mode. Press this button to advance the video. If the DVD is paused, pressing this button will advance the video frame by frame. STOP Button (13) This button only functions in DVD video mode. Press this button to stop the DVD. MENU Button (14) This button only functions in DVD video mode. Press this button to select the DVD disc menu.
UNDERSTANDING YOUR INSTRUMENT PANEL Remote Control Battery Service • To replace the batteries for the remote control slide the cover rearward. The replacement batteries for the remote control are two AAA batteries. Operating Instructions — Video Screen Push up on the release button to lower the video screen. Screen handle 1. Screen Width Button Changes the width of the screen picture.
UNDERSTANDING YOUR INSTRUMENT PANEL 229 2. Enter Button This button will enter the selection from the on-screen menu. 3. Brightness Button Changes the brightness of the screen picture.
UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions — Headphones Power Button Pressing the power button will turn the headphones ON/OFF. An indicator light will illuminate on the headphone earpiece to indicate the headphones are ON. NOTE: • The headphones will turn off automatically in approximately 3 minutes if they lose the signal form the system or when the radio or rear audio/video system is turned off.
UNDERSTANDING YOUR INSTRUMENT PANEL 231 Headphone Battery Service • Press the button at the bottom of each headphone earpiece and lift the cover upward. General Information This device complies with part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) This device must accept any interference received, including interference that may cause undesired operation.
UNDERSTANDING YOUR INSTRUMENT PANEL 3. Direct sunlight or objects blocking the line of sight between the headphone transmitter on the video screen and the headphones. NOTE: To operate a video game unit a DC to AC adapter may be required, plug the adapter into any power outlet. Operating Instructions — MP3 Player, Portable Walkman An MP3 player can be connected to the audio system. Connect the cables to the RCA jacks located on the front of the CD/DVD changer.
UNDERSTANDING YOUR INSTRUMENT PANEL 233 The navigation DVD unit is located in the underfloor storage compartment in the rear cargo area. A single disc containing map information for the entire United States and parts of Canada is stored in the DVD unit. Updated DVD’s are available from your authorized dealer. To replace the navigation map DVD lift the storage bin cover and liner in the rear cargo area, press the eject button and the disc will eject.
UNDERSTANDING YOUR INSTRUMENT PANEL System Activation To activate your Sirius Satellite Radio service, call the toll-free number 888-539-7474, or visit the Sirius web site at www.sirius.com. Please have the following information available when activating your system: 1. The Electronic Serial Number/Sirius Identification Number (ESN/SID). 2. Credit card information. 3. Your Vehicle Identification Number.
UNDERSTANDING YOUR INSTRUMENT PANEL 235 mode when any other button is pushed, the ignition is turned OFF, or 5 minutes has passed since any button was pushed. Selecting Satellite Mode in RBB, RAH and RBK Radios Press the MODE button repeatedly until ⬙S A⬙ appears in the display. A CD or tape may remain in the radio while in the Satellite radio mode. Selecting Satellite Mode in RBP, RBU, RAZ, RB1 and RBQ Radios Press the MODE button repeatedly until the word ⬙SIRIUS⬙ appears in the display.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Channels that may contain objectionable content can be blocked. Contact Sirius Customer Care at 888-5397474 to discuss options for channel blocking or unblocking. Please have your ESN/SID information available. Storing and Selecting Pre-Set Channels In addition to the 10 AM and 10 FM pre-set stations, you may also commit 10 satellite stations to push button memory. These satellite channel pre-set stations will not erase any AM or FM pre-set memory stations.
UNDERSTANDING YOUR INSTRUMENT PANEL 237 Satellite Antenna To ensure optimum reception, do not place items on the roof around the rooftop antenna location or strap items to the trunk lid around the trunk lid antenna (if equipped). Metal objects placed within the line of sight of the antenna will cause decreased performance. Larger luggage items such as bikes should be placed as far rearward as possible, within the loading design of the rack. Do not place items directly on or above the antenna.
UNDERSTANDING YOUR INSTRUMENT PANEL The left hand rocker switch has a push button in the center. The function of the left hand switch is different depending on which mode you are in. The following describes the left hand rocker switch operation in each mode: Radio Operation Pressing the top of the switch will SEEK up for the next listenable station and pressing the bottom of the switch will SEEK down for the next listenable station.
UNDERSTANDING YOUR INSTRUMENT PANEL 239 CASSETTE TAPE AND PLAYER MAINTENANCE To keep the cassette tapes and player in good condition, take the following precautions: 1. Do not use cassette tapes longer than C-90; otherwise, sound quality and tape durability will be greatly diminished. 2. Keep the cassette tape in its case to protect from slackness and dust when it is not in use. 3. Keep the cassette tape away from direct sunlight, heat and magnetic fields such as the radio speakers. 4.
UNDERSTANDING YOUR INSTRUMENT PANEL CD/DVD DISC MAINTENANCE To keep the CD/DVD discs in good condition, take the following precautions: 1. Handle the disc by its edge; avoid touching the surface. 2. If the disc is stained, clean the surface with a soft cloth, wiping from center to edge. 3. Do not apply paper, paper CD labels, or tape to the disc; avoid scratching the disc. 4. Do not use solvents such as benzine, thinner, cleaners, or antistatic sprays. 5. Store the disc in its case after playing. 6.
UNDERSTANDING YOUR INSTRUMENT PANEL 241 Manual Air Conditioning and Heating System second time the indicator light turns off, the blower will turn off and the system will be positioned in the recirculation mode. Blower Control The Blower controls the amount of air delivered to the passenger compartment. There are four blower speeds. The fan speed increases as you move the control clockwise.
UNDERSTANDING YOUR INSTRUMENT PANEL Dual Zone Temperature Control — If Equipped With the Dual Zone Temperature Control System, each front seat occupant can independently control the temperature of air coming from the outlets on their side of the vehicle. Mode Control The mode control allows you to choose from several patterns of air distribution. NOTE: To improve your selection choices, the system allows you to operate at intermediate positions between the major modes.
UNDERSTANDING YOUR INSTRUMENT PANEL 243 Air comes from the outlets in the instrument panel. Each of these outlets can be individually adjusted to direct the flow of air. Moving the air vane knob on the center outlets down, will close off the air flow from the center outlets. The thumbwheel next to the outboard outlets can be rotated to regulate or shut off the air flow from these outlets.
UNDERSTANDING YOUR INSTRUMENT PANEL Air comes from both the instrument panel outlets, floor outlets and defrost. A slight amount of air is also directed through the side window demister outlets. Bi-Level Mode NOTE: In many temperature lever positions, the bilevel mode is designed to provide cooler air out of the panel outlets and warmer air from the floor outlets.
UNDERSTANDING YOUR INSTRUMENT PANEL 245 Floor Mode Mix Mode 4 Floor Outlets Mix Outlets Air comes from the floor outlets. A slight amount of air is directed through the defrost and side window demister outlets. Air comes from the floor, defrost and side window demist outlets. This mode works best in cold or snowy conditions. It allows you to stay comfortable while keeping the windshield clear.
UNDERSTANDING YOUR INSTRUMENT PANEL Defrost modes are selected. This is done to assist in drying the air and it will help in keeping the windows from fogging. Defrost Mode Manual Air Conditioning Operation To turn on the air conditioning, set the front blower control to any speed and press the A/C button which is located next to the recirculation button. An indicator light on the A/C button shows that the air conditioning is on.
UNDERSTANDING YOUR INSTRUMENT PANEL 247 NOTE: • The compressor will not engage until the engine has been running for a few seconds. • If your air conditioning performance seems lower than expected, check the A/C air filter (ATC equipped vehicles only) and the front of the A/C condenser for an accumulation of dirt or insects. The A/C condenser is located in front of the radiator. The A/C air filter is located under the instrument panel on the passenger side.
UNDERSTANDING YOUR INSTRUMENT PANEL • If the recirculation button is pressed while in the Mix or Defrost mode, the indicator light in the recirculation button will flash 3 times indicating that recirculation is not allowed. • Turn the ignition switch to the OFF position. A/C Recirculation Programming The recirculation control is programmed to cancel the recirculation mode when the ignition key is turned OFF and will reset to outside air mode when the ignition key is turned ON.
UNDERSTANDING YOUR INSTRUMENT PANEL 249 Dual-Zone Automatic Temperature Control The Dual Zone Automatic Temperature Control (ATC) System automatically maintains the interior comfort level desired by the driver and front seat passenger. This is accomplished by using two infrared sensors located in the center of the instrument panel. The two infrared sensors independently measure the surface temperature of the driver and front seat passenger.
UNDERSTANDING YOUR INSTRUMENT PANEL temperature you would like the system to maintain. When the system is set to your comfort level, it is not necessary to change the settings. You will experience the greatest efficiency by allowing the system to function automatically. The system will operate fully automatically in either ⬙AUTO HI⬙ or ⬙AUTO LO⬙. The ⬙AUTO LO⬙ setting will limit the maximum fan speed and should be used when more quiet operation is desired.
UNDERSTANDING YOUR INSTRUMENT PANEL 251 This feature may be enabled using the following procedure: • Press and hold the Heated Rear Window and Auto HI buttons for 5 seconds. • The “DELAY” symbol will flash to indicate that the feature as been enabled. Power Button This button turns the entire system ON/OFF. When the system is turned on it will return to the previous settings.
UNDERSTANDING YOUR INSTRUMENT PANEL The front blower control can be set to any fixed blower speed by pressing the rocker switch up or down. This allows the front occupants to control the volume of air circulated in the vehicle and cancel the auto mode. The fan will now operate at a fixed speed until additional speeds are selected or until either the ⬙AUTO HI⬙ or ⬙AUTO LO⬙ buttons are pressed. The system will continue to automatically adjust air temperature and airflow distribution.
UNDERSTANDING YOUR INSTRUMENT PANEL 253 Air comes from both the instrument panel outlets and floor outlets. A slight amount of air is also directed through the defrost and side window demister outlets. Bi-Level Mode NOTE: In many temperature positions, the bi-level mode is designed to provide cooler air out of the panel outlets and warmer air from the floor outlets.
UNDERSTANDING YOUR INSTRUMENT PANEL Floor Mode Mix Mode Floor Outlets Mix Outlets Air comes from the floor outlets. A slight amount of air is directed through the defrost and side window demister outlets. Air comes from the floor, defrost and side window demist outlets. This mode is not used when operating in either ⬙AUTO HI⬙ or ⬙AUTO LO⬙. This mode should be used when airflow to the floor and windshield is desired.
UNDERSTANDING YOUR INSTRUMENT PANEL 255 windshield or side glass starts to impair visibility, press the front blower button and increase the fan speed to maximum. Defrost Mode NOTE: While operating in ⬙AUTO HI⬙ or ⬙AUTO LO⬙, the system will not automatically sense the presence fog, mist, or ice on the windshield. The defrost button must be pressed to clear the windshield and side glass. Defrost Outlets Depress the “A/C” button to turn on and off the air conditioning during manual operation only.
UNDERSTANDING YOUR INSTRUMENT PANEL windshield or side glass starts to impair visibility, press the front blower button and increase the fan speed to maximum. Recirculation Control When the outside air contains smoke, odors, high humidity, or if rapid cooling is desired you may wish to recirculate interior air by pressing the recirculation button. The recirculation mode should only be used temporarily. The recirculate symbol will illuminate in the display when this button is selected.
UNDERSTANDING YOUR INSTRUMENT PANEL 257 • While holding the recirculation button, turn the ignition switch to the “RUN” position. • Continue holding the recirculation button for 4 seconds, then release. The recirculation control is now programmed so that the recirculation mode will not reset to the outside air mode when the engine is restarted. The recirculation programming can be changed back by repeating this procedure. Rear Blower Operation To operate the rear fan, press the ⬙REAR⬙ button.
UNDERSTANDING YOUR INSTRUMENT PANEL glycol antifreeze coolant in water is recommended. Refer to section 7, Maintenance Procedures, of this manual for proper coolant selection. Winter Operation To insure the best possible heater and defroster performance, make sure the engine cooling system is functioning properly and the proper amount, type, and concentration of coolant is used. Refer to section 7, Maintenance Procedures, of this manual for proper coolant selection.
UNDERSTANDING YOUR INSTRUMENT PANEL 259 A/C Air Filter — If Equipped On vehicles equipped with Automatic Temperature Control (ATC), the climate control system filters out dust and pollen from the air. Refer to section 7 “Air Conditioning” for filter replacement instructions. Outside Temperature Display The outside temperature can be shown in the ATC display by pressing the ⬙OUTSIDE TEMP⬙ button.
STARTING AND OPERATING CONTENTS 䡵 Starting Procedures . . . . . . . . . . . . . . . . . . . . . 266 䡵 Automatic Transmission . . . . . . . . . . . . . . . . . . 270 ▫ Automatic Transmission . . . . . . . . . . . . . . . . 267 ▫ Brake/Transmission Interlock System . . . . . . . 271 ▫ Normal Starting (Above 32°F / 0°C) . . . . . . . . 267 ▫ Automatic Transmission Ignition Interlock System . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
STARTING AND OPERATING 䡵 Parking Brake . . . . . . . . . . . . . . . . . . . . . . . . . 276 䡵 Tire Safety Information . . . . . . . . . . . . . . . . . . . 288 䡵 Brake System . . . . . . . . . . . . . . . . . . . . . . . . . . 278 ▫ Tire Markings . . . . . . . . . . . . . . . . . . . . . . . . 288 ▫ Anti-Lock Brake System . . . . . . . . . . . . . . . . 279 ▫ Tire Identification Number (TIN) . . . . . . . . . . 292 䡵 Electronic Stability Program (ESP) . . . . . . . . . . .
STARTING AND OPERATING 263 ▫ Replacement Tires . . . . . . . . . . . . . . . . . . . . . 304 ▫ Alignment And Balance . . . . . . . . . . . . . . . . . 305 䡵 Tire Chains . . . . . . . . . . . . . . . . . . . . . . . . . . . 306 䡵 Snow Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . 307 ▫ Using Your Compact Spare — Basic Tire Pressure Monitoring System Only . . 313 ▫ Tire Pressure Monitoring Premium System – If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 314 䡵 Tire Rotation . . .
STARTING AND OPERATING ▫ Carbon Monoxide Warnings . . . . . . . . . . . . . . 321 ▫ Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . 326 䡵 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . 321 䡵 Vehicle Loading . . . . . . . . . . . . . . . . . . . . . . . . 326 ▫ Fuel Filler Cap (Gas Cap) . . . . . . . . . . . . . . . 321 ▫ Vehicle Certification Label . . . . . . . . . . . . . . . 327 ▫ Loose Fuel Filler Cap Message . . . . . . . . . . . .
STARTING AND OPERATING 265 ▫ Towing Requirements . . . . . . . . . . . . . . . . . . 336 ▫ Towing Tips . . . . . . . . . . . . . . . . . . . . . . . . . 340 䡵 Recreational Towing (Behind Motorhome, Etc.) . . 342 ▫ Towing This Vehicle Behind Another Vehicle (Flat Towing With All Four Wheels On The Ground) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
STARTING AND OPERATING STARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. WARNING! • Be sure to turn off the engine if you want to rest or sleep in your car. Accidents can be caused by inadvertently moving the gear selection lever or by pressing the accelerator pedal. This may cause excessive heat in the exhaust system, resulting in overheating and vehicle fire which may cause serious or fatal injuries.
STARTING AND OPERATING 267 Automatic Transmission The gear selector must be in the NEUTRAL or PARK position before you can start the engine. Depress the brake pedal before shifting into any driving gear. Normal Starting (Above 32°F / 0°C) 1. Do not depress the accelerator. 2. Turn and hold the ignition key in the START position and release when engine starts. 3. If engine does not start after 3 seconds, depress the accelerator lightly (while still cranking the engine). 4.
STARTING AND OPERATING If Engine Fails To Start If the engine fails to start after you have followed the normal starting procedure, it may be flooded. Push the accelerator pedal all the way to the floor and hold it there while cranking the engine. This should clear any excess fuel in case the engine is flooded. CAUTION! To prevent damage to the starter, do not crank the engine for more than 15 seconds at a time. Wait 10 to 15 seconds before trying again.
STARTING AND OPERATING 269 WARNING! Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transmission cannot be started this way. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle. If the vehicle has a discharged battery, booster cables may be used to obtain a start from a booster battery or the battery in another vehicle. This type of start can be dangerous if done improperly.
STARTING AND OPERATING ENGINE BLOCK HEATER — IF EQUIPPED The engine block heater warms engine coolant and permits quicker starts in cold weather. Connect the cord to a standard 110-115 volt AC electrical outlet with a grounded, three-wire extension cord. The engine block heater cord is routed under the hood on the driver side of the vehicle. It has a removable cap that is located on the driver side of the Integrated Power Module. WARNING! Remember to disconnect the cord before driving.
STARTING AND OPERATING 271 WARNING! It is dangerous to shift the selector lever out of “P” or “N” if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in reverse. You could lose control of the vehicle and hit someone or something. Only shift into gear when the engine is idling normally and when your right foot is firmly on the brake pedal.
STARTING AND OPERATING Reset Mode - Electronic Transmission The transmission is monitored electronically for abnormal conditions. If a condition is detected that could cause damage, the transmission automatically shifts into second gear. The transmission remains in second gear despite the forward gear selected. Park (P), Reverse (R), and Neutral (N) will continue to operate. This Reset feature allows the vehicle to be driven to a dealer for service without damaging the transmission.
STARTING AND OPERATING 273 WARNING! Never use Park position on an automatic transmission as a substitute for the parking brake. Always apply parking brake fully when parked to guard against vehicle movement and possible injury or damage. pressed, the shifter can be moved out of the park position without pressing the brake. After operation return the shifter bezel ring to its original position. For electrical system malfunctions there is an override for the interlock system.
STARTING AND OPERATING “N” Neutral Engine may be started in this range. “D” Overdrive To be used for most city and highway driving, it provides smoothest upshifts and downshifts and best fuel economy. When frequent transmission shifting occurs while using the “D” Overdrive position, such as when operating the vehicle under heavy loading conditions, (i.e. in hilly terrain, traveling into strong head winds or while towing heavy trailers), use the AutoStick mode and select the “3” range.
STARTING AND OPERATING 275 You can shift in or out of the AutoStick mode at any time without taking your foot off the accelerator pedal. If you choose the Overdrive mode, the transmission will operate automatically; shifting between the four available gears. When you wish to engage AutoStick, simply move the shift lever to the AUTOSTICK position. The transmission will remain in the current gear until an upshift or downshift is chosen. • You can start out in first, second, or third gear.
STARTING AND OPERATING • If the system detects a problem it will disable the AutoStick mode and the transmission will return to the automatic mode until the problem is corrected. ALL WHEEL DRIVE — IF EQUIPPED This feature provides full time, on-demand, All Wheel Drive (AWD). The system is automatic with no driver inputs or additional driving skills required. Under normal driving conditions, the front wheels provide most of the traction.
STARTING AND OPERATING 277 Before leaving the vehicle, make sure that the parking brake is fully applied and place the gear selector in the Park position. To release the parking brake, pull out on the parking brake release located on the left side of the instrument panel. When parking on a hill, it is important to set the parking brake before placing the gear selector in Park, otherwise the load on the transmission locking mechanism may make it difficult to move the selector out of park.
STARTING AND OPERATING WARNING! • Always fully apply the parking brake when leaving your vehicle, or it may roll and cause damage or injury. Also be certain to leave an automatic transmission in Park, a manual transmission in Reverse or first gear. Failure to do so may allow the vehicle to roll and cause damage or injury. • NEVER leave children alone in a vehicle. Leaving children in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured.
STARTING AND OPERATING 279 Anti-Lock Brake System The Anti-Lock Brake System provides increased vehicle stability and brake performance under most braking conditions. The system automatically “pumps” the brakes during severe braking conditions to prevent wheel lock-up. WARNING! Pumping of the Anti-Lock Brakes will diminish their effectiveness and may lead to an accident. Pumping makes the stopping distance longer. Just press firmly on your brake pedal when you need to slow down or stop.
STARTING AND OPERATING The ABS light monitors the Anti-Lock Brake System. The light will come on when the ignition switch is turned to the ON position and may stay on for as long as four seconds. If the ABS light remains on or comes on while driving, it indicates that the Anti-Lock portion of the brake system is not functioning and that service is required. However, the conventional brake system will continue to operate normally if the BRAKE warning light is not on.
STARTING AND OPERATING 281 • and a slight drop or fall away of the brake pedal at the end of the stop. These are all normal characteristics of ABS. WARNING! The Anti-Lock Brake System contains sophisticated electronic equipment that may be susceptible to interference caused by improperly installed or high output radio transmitting equipment. This interference can cause possible loss of anti-lock braking capability. Installation of such equipment should be performed by qualified professionals.
STARTING AND OPERATING applies the brake of the appropriate wheel to assist in counteracting the Over-steer or Under-steer condition. WARNING! • Over-steer: when the vehicle is turning more than appropriate for the steering wheel position. Electronic Stability Program (ESP) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions.
STARTING AND OPERATING 283 ESP has the following operating modes: • ESP On This is the normal operating mode for ESP. Whenever the vehicle is started the ESP system will be in this mode. This mode should be used for almost all driving situations. ESP should only be turned to “Partial Off” for specific reasons as noted below. • Partial Off This mode is entered by momentarily depressing the “ESP Control Switch”.
STARTING AND OPERATING go out with the engine running. If the “ESP/BAS Warning Lamp” comes on continuously with the engine running, a malfunction has been detected in either the ESP or BAS system, or both. If this light remains on after several ignition cycles, and the vehicle has been driven several miles at speeds greater than 30 mph (48 km/h), see your authorized dealer as soon as possible to have the problem diagnosed and corrected.
STARTING AND OPERATING 285 TRACTION CONTROL The system is always in the “stand by” mode unless, This system monitors the amount of wheel spin of each of the driven wheels. If wheel spin is detected, brake pressure is applied to the slipping wheel(s) and engine power is reduced to provide enhanced acceleration and stability. A feature of the TCS system functions similar to a limited slip differential and controls the wheel spin across a driven axle.
STARTING AND OPERATING • The system has been deactivated to prevent damage to the brake system due to overheated brake temperatures NOTE: • The Traction Control system will make buzzing or clicking sounds when in operation. • Extended heavy use of Traction Control may cause the system to deactivate and turn on the traction control indicator located in the instrument cluster. This is to prevent overheating of the brake system and is a normal condition.
STARTING AND OPERATING 287 WARNING! Continued operation with reduced power steering assist could pose a safety risk to yourself and others. Service should be obtained as soon as possible. DRIVING ON SLIPPERY SURFACES Acceleration Rapid acceleration on snow covered, wet, or other slippery surfaces may cause the front wheels to pull erratically to the right or left. This phenomenon occurs when there is a difference in the surface traction under the front (driving) wheels.
STARTING AND OPERATING Traction When driving on wet or slushy roads, it is possible for a wedge of water to build up between the tire and road surface. This is known as hydroplaning and may cause partial or complete loss of vehicle control and stopping ability. To reduce this possibility, the following precautions should be observed: TIRE SAFETY INFORMATION Tire Markings 1. Slow down during rainstorms or when roads are slushy. 2. Slow down if road has standing water or puddles. 3.
STARTING AND OPERATING 289 • European Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter ⬙P⬙ is absent from this tire size designation. Example: 215/65R15 96H • Temporary Spare tires are high-pressure compact spares designed for temporary emergency use only. Tires designed to this standard have the letter “T” molded into the sidewall preceding the size designation.
STARTING AND OPERATING Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ⴖ....blank....ⴖ = Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary Spare tire 31 = Overall Diameter in Inches (in) 215 = Section Width in Millimeters (mm) 65 = Aspect Ratio in Percent (%) —Ratio of section height to section width of tire. 10.
STARTING AND OPERATING 291 EXAMPLE: Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry. H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions. —The maximum speed corresponding to the Speed Symbol should only be achieved under specified operating conditions. (i.e. tire pressure, vehicle loading, road conditions, and posted speed limits).
STARTING AND OPERATING Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire; however, the date code may only be on one side. Tires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire. Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the outboard side then you will find it on the inboard side of the tire.
STARTING AND OPERATING 293 Tire Loading and Tire Pressure Tire and Loading Information Placard Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on either the face of the driver’s door or the driver’s side “B” pillar.
STARTING AND OPERATING Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the “Tire and Loading Information” placard and in the “Vehicle Loading” section of this manual.
STARTING AND OPERATING 295 5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4. 6. If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle.
STARTING AND OPERATING
STARTING AND OPERATING 297 WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle. Three primary areas are affected by improper tire pressure: 1.
STARTING AND OPERATING 2. Economy— Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Under inflation, also increases tire rolling resistance and results in higher fuel consumption. 3. Ride Comfort and Vehicle Stability— Proper tire inflation contributes to a comfortable ride. Over inflation produces a jarring and uncomfortable ride.
STARTING AND OPERATING 299 CAUTION! After inspecting or adjusting the tire pressure, always reinstall the valve stem cap (if equipped). This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressures specified on the placard are always “cold tire inflation pressure.” Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or driven less than 1 mile (1 km) after a 3 hour period.
STARTING AND OPERATING loading may be required for high-speed vehicle operation. Refer to original equipment or an authorized tire dealer for recommended safe operating speeds, loading and cold tire inflation pressures. WARNING! High speed driving with your vehicle under maximum load is dangerous. The added strain on your tires could cause them to fail. You could have a serious accident. Don’t drive a vehicle loaded to the maximum capacity at continuous speeds above 75 mph (120 km/h).
STARTING AND OPERATING 301 Compact Spare Tire — If Equipped The compact spare is for temporary emergency use with radial tires. It is engineered to be used on your style vehicle only. Since this tire has limited tread life, the original tire should be repaired (or replaced) and reinstalled at the first opportunity. Do not install a wheel cover or attempt to mount a conventional tire on the compact spare wheel, since the wheel is designed specifically for the compact spare.
STARTING AND OPERATING Limited Use Spare — If Equipped The limited use spare tire is for temporary emergency use on your vehicle. This tire is identified by a limited use spare tire warning label located on the limited use spare tire and wheel assembly. This tire may look like the original equipped tire on the front or rear axle of your vehicle, but it is not. Installation of this limited use spare tire affects vehicle handling.
STARTING AND OPERATING 303 WARNING! Fast spinning tires can be dangerous. Forces generated by excessive wheel speeds may cause tire damage or failure. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 30 mph (48 km/h) for more than 30 seconds continuously when you are stuck, and don’t let anyone near a spinning wheel, no matter what the speed.
STARTING AND OPERATING Life of Tire The service life of a tire is dependent upon varying factors including but not limited to: Keep dismounted tires in a cool, dry place with as little exposure to light as possible. Protect tires from contact with oil, grease, and gasoline. • Driving style Replacement Tires The tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for wear and correct cold tire inflation pressure.
STARTING AND OPERATING 305 WARNING! CAUTION! • Do not use a tire, wheel size or rating other than that Replacing original tires with tires of a different size may result in false speedometer and odometer readings. specified for your vehicle. Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle.
STARTING AND OPERATING Improper alignment will not cause vehicle vibration. Vibration may be a result of tire and wheel out-ofbalance. Proper balancing will reduce vibration and avoid tire cupping and spotty wear. TIRE CHAINS Use only compact chains, or other traction aids that meet SAE type “Class S” specifications. Chains must be the proper size for the vehicle, as recommended by the chain manufacturer. NOTE: Do not use tire chains on a compact spare tire.
STARTING AND OPERATING 307 NOTE: In order to avoid damage to tires, chains, and your vehicle do not drive for a prolonged period of time on dry pavement. Observe the tire chain manufacturer’s instructions on method of installation, operating speed, and conditions for usage. Always use the lower suggested operating speed if both the chain manufacturer and vehicle manufacture suggest a maximum speed. This notice applies to all chain traction devices, including link and cable (radial) chains.
STARTING AND OPERATING Follow the recommended tire rotation frequency for your type of driving found in the “Maintenance Schedules” Section of this manual. More frequent rotation is permissible if desired. The reasons for any rapid or unusual wear should be corrected prior to rotation being performed. TIRE PRESSURE MONITOR SYSTEM — IF EQUIPPED The suggested rotation method is the “forward-cross” shown in the following diagram. • The tire pressure will vary with the temperature by about 1 psi (6.
STARTING AND OPERATING 309 • The Tire Pressure Monitoring System (TPMS) will warn the driver of a low tire pressure if the tire pressure falls below the low pressure warning threshold for any reason, including low temperature effects. • The Tire Pressure Monitoring System (TPMS) will continue to warn the driver of low tire pressure as long as the condition exists, and will not turn off until the tire pressure is at or above recommended cold placard pressure.
STARTING AND OPERATING Tire Pressure Monitoring Low Pressure Warnings The Tire Pressure Monitoring Telltale Lamp will illuminate in the instrument cluster and an audible chime will be activated when one or more of the four active road tire pressures are low. The audible chime will sound once every ignition cycle for each low tire condition that it detects.
STARTING AND OPERATING 311 The Tire Pressure Monitor System (TPMS) consists of the following components: • Receiver Module • 4 Tire Pressure Monitoring Sensors • Various Tire Pressure Monitoring System Messages, which display in the Electronic Vehicle Information Center (EVIC) • Tire Pressure Monitoring Telltale Lamp The Tire Pressure Monitoring Telltale Lamp will illuminate in the instrument cluster and an audible chime will be activated when one or more of the four active road tire pressures are low.
STARTING AND OPERATING Service Tire System Soon The Tire Pressure Monitoring Telltale Lamp will flash on and off for 60 seconds in the instrument cluster, and an audible chime will be activated when one or more of the four active road tire pressures are low. In addition the Electronic Vehicle Information Center (EVIC) will display a “SERVICE TIRE SYSTEM SOON” text message. The flash cycle will repeat every ten minutes, without an audible chime, until the condition no longer exists.
STARTING AND OPERATING 313 CAUTION! After inspecting or adjusting the tire pressure always reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the wheel rim sensor. NOTE: • The Tire Pressure Monitoring System does not monitor the temporary spare tire. • The TPMS is not intended to replace normal tire care and maintenance, or to provide warning of a tire failure or condition.
STARTING AND OPERATING Monitoring Lamp to be ON, and a Chime will sound. This sequence will repeat for every key cycle until the original Tire Pressure Monitoring System tire has been properly repaired (or replaced) and put back on the vehicle in place of the compact spare tire. • Receiver Module Tire Pressure Monitoring Premium System – If Equipped The Tire Pressure Monitor System (TPMS) uses wireless technology with wheel rim mounted electronic sensors to monitor tire pressure levels.
STARTING AND OPERATING 315 NOTE: A low spare tire will not cause the Tire Pressure Monitoring System Telltale Lamp to illuminate or the chime to sound. Should a low tire condition occur on any of the four active road tire(s), you should stop as soon as possible, and inflate the low tire(s) that is/are flashing on the graphic display to the vehicle’s recommended cold placard pressure value.
STARTING AND OPERATING NOTE: Your vehicle is equipped with a compact spare wheel and tire assembly that does not have a tire pressure monitoring sensor. Therefore, it will not be monitored by the Tire Pressure Monitoring System.
STARTING AND OPERATING 317 CAUTION! After inspecting or adjusting the tire pressure always reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the wheel rim sensor. NOTE: • The Tire Pressure Monitoring System (TPMS) is not intended to replace normal tire care and maintenance, nor to provide warning of a tire failure or condition.
STARTING AND OPERATING FUEL REQUIREMENTS Your vehicle is designed to meet all emissions regulations and provide satisfactory fuel economy and performance when using high quality unleaded gasoline having an octane range of 87 to 89 or higher. The manufacturer recommends the use of 89 octane for optimum performance. Light spark knock at low engine speeds is not harmful to your engine. However, continued heavy spark knock at high speeds can cause damage and immediate service is required.
STARTING AND OPERATING 319 Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with oxygenates such as 10% ethanol, MTBE, and ETBE. Oxygenates are required in some areas of the country during the winter months to reduce carbon monoxide emissions. Fuels blended with these oxygenates may be used in your vehicle. CAUTION! DO NOT use gasolines containing Methanol or E85 Ethanol.
STARTING AND OPERATING Materials Added to Fuel All gasoline sold in the United States is required to contain effective detergent additives. Use of additional detergents or other additives are not needed under normal conditions and would result in additional cost. Therefore you should not have to add anything to the fuel. Fuel System Cautions CAUTION! Follow these guidelines to maintain your vehicle’s performance: • The use of leaded gas is prohibited by Federal law.
STARTING AND OPERATING 321 Carbon Monoxide Warnings WARNING! Carbon monoxide (CO) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: the vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side windows fully open. • Keep the liftgate closed when driving your vehicle to prevent carbon monoxide and other poisonous exhaust gases from entering the vehicle. ADDING FUEL • Do not inhale exhaust gases.
STARTING AND OPERATING The fuel tank filler tube has a restricting door about 2 inches (50 mm) inside the opening. If using a portable fuel container, it should have a flexible nozzle long enough to force open the restricting door. CAUTION! Damage to the fuel system or emission control system could result from using an improper fuel tank filler tube cap (gas cap).
STARTING AND OPERATING 323 NOTE: • Tighten the fuel filler cap until you hear a “clicking” sound. This is an indication that the fuel filler cap is properly tightened. • If the gas cap is not tighten properly, the Malfunction Indicator Light will come on. Be sure the gas cap is tightened every time the vehicle is refueled. WARNING! A fire may result if gasoline is pumped into a portable container that is inside of a vehicle. You could be burned. Always place gas containers on the ground while filling.
STARTING AND OPERATING FLEXIBLE FUEL— (Fleet Vehicles Only) E-85 General Information The information in this section is for Flexible Fuel vehicles only. These vehicles can be identified by the unique fuel filler door label that states Ethanol (E-85) or Unleaded Gasoline Only. This section only covers those subjects that are unique to these vehicles. Please refer to the other sections of this manual for information on features that are common between Flexible Fuel and gasoline only powered vehicles.
STARTING AND OPERATING 325 For best results, a refueling pattern that alternates between E-85 and unleaded gasoline should be avoided.
STARTING AND OPERATING Cruising Range Because E-85 fuel contains less energy per gallon than gasoline, you will experience an increase in fuel consumption. You can expect your MPG and your driving range to decrease by about 30% compared to gasoline operation. Maintenance If you operate the vehicle using E-85 fuel, follow Schedule B in the maintenance schedule section of this manual. Replacement Parts Many components in your Flexible Fuel Vehicle (FFV) are designed to be compatible with ethanol.
STARTING AND OPERATING 327 Vehicle Certification Label Your vehicle has a certification label attached to the rear of the driver’s door.
STARTING AND OPERATING Overloading The load carrying components (axle, springs, tires, wheels, etc.) of your vehicle will provide satisfactory service as long as you do not exceed the GVWR and front and rear GAWR. The best way to figure out the total weight of your vehicle is to weigh it when it is fully loaded and ready for operation. Weigh it on a commercial scale to insure that it is not over the GVWR. Figure out the weight on the front and rear of the vehicle separately.
STARTING AND OPERATING 329 A loaded vehicle is shown in the illustration. Note that neither the GVWR or the GAWR capacities have been exceeded.
STARTING AND OPERATING Common Towing Definitions The following trailer towing related definitions will assist you in understanding the following information: Gross Vehicle Weight Rating (GVWR) The GVWR is the total allowable weight of your vehicle. This includes driver, passengers, cargo and tongue weight. The total load must be limited so that you do not exceed the GVWR.
STARTING AND OPERATING 331 Tongue Weight (TW) The downward force exerted on the hitch ball by the trailer. In most cases it should not be less than 10% or more than 15% of the trailer load. You must consider this as part of the load on your vehicle. Frontal Area The maximum height and maximum width of the front of a trailer.
STARTING AND OPERATING WARNING! An improperly adjusted Weight Distributing Hitch system may reduce handling, stability, braking performance, and could result in an accident. Weight Distributing Systems may not be compatible with Surge Brake Couplers. Consult with your hitch and trailer manufacturer or a reputable Recreational Vehicle dealer for additional information.
STARTING AND OPERATING 333 The following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition. Refer to the Trailer Towing Weights (Maximum Trailer Weight Ratings) chart for the Max. GTW towable for your given drivetrain.
STARTING AND OPERATING Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/Transmission GCWR (Gross Combined Wt. Rating) 3.5L & 3.8L Auto8,600 lbs (3900 kg) matic Frontal Area 40 SQ. FT. 8,600 lbs (3900 kg) 40 SQ. FT. 8,600 lbs (3900 kg) 40 SQ. FT. Max. GTW (Gross Trailer Wt.
STARTING AND OPERATING 335 Trailer and Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% to 15% of the Gross Trailer Weight (GTW) on the tow hitch of your vehicle. Loads balanced over the wheels or heavier in the rear can cause the trailer to sway severely side to side which will cause loss of control of the vehicle and trailer. Failure to load trailers heavier in front is the cause of many trailer accidents.
STARTING AND OPERATING NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options, or dealer-installed options, must be considered as part of the total load on your vehicle. Refer to the Tire and Loading Information placard in the Tire Safety Information Section of this manual for the maximum combined weight of occupants and cargo for your vehicle.
STARTING AND OPERATING 337 WARNING! Improper towing can lead to an injury accident. Follow these guidelines to make your trailer towing as safe as possible: Make certain that the load is secured in the trailer and will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control. You could lose control of your vehicle and have an accident.
STARTING AND OPERATING 4. Tongue weight rating for the trailer hitch utilized (This requirement may limit the ability to always achieve the 10% to 15% range of tongue weight as a percentage of total trailer weight). Towing Requirements — Tires − Do not attempt to tow a trailer while using a compact spare tire. − Proper tire inflation pressures are essential to the safe and satisfactory operation of your vehicle.
STARTING AND OPERATING 339 − Trailer brakes are recommended for trailers over 1,000 lbs (454 kg) and required for trailers in excess of 2,000 lbs (907 kg). CAUTION! If the trailer weighs more than 1,000 lbs (454 kg) loaded, it should have its own brakes and they should be of adequate capacity. Failure to do this could lead to accelerated brake lining wear, higher brake pedal effort, and longer stopping distances. WARNING! Do not connect trailer brakes to your vehicle’s hydraulic brake lines.
STARTING AND OPERATING NOTE: Do not cut or splice wiring into the vehicles wiring harness. The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. Refer to the following illustrations. 7- Pin Connector Towing Tips Before setting out on a trip, practice turning, stopping and backing the trailer in an area away from heavy traffic.
STARTING AND OPERATING 341 Towing Tips — Automatic Transmission The “D” range can be selected when towing. However, if frequent shifting occurs while in this range, the “3” range should be selected. NOTE: Using the “3” range while operating the vehicle under heavy operating conditions will improve performance and extend transmission life by reducing excessive shifting and heat build up. This action will also provide better engine braking.
STARTING AND OPERATING − Highway Driving Reduce speed. RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) − Air Conditioning Turn off temporarily. TOWING THIS VEHICLE BEHIND ANOTHER VEHICLE (Flat towing with all four wheels on the ground) Recreational towing for this vehicle is not recommended. − refer to Cooling System Operating information in the Maintenance section of this manual for more information. NOTE: If the vehicle requires towing make sure all four wheels are off the ground.
WHAT TO DO IN EMERGENCIES CONTENTS 䡵 Hazard Warning Flasher . . . . . . . . . . . . . . . . . . 344 䡵 Freeing A Stuck Vehicle . . . . . . . . . . . . . . . . . . 356 䡵 If Your Engine Overheats . . . . . . . . . . . . . . . . . 345 䡵 Towing A Disabled Vehicle . . . . . . . . . . . . . . . . 357 䡵 Jacking And Tire Changing . . . . . . . . . . . . . . . . 346 ▫ With Ignition Key . . . . . . . . . . . . . . . . . . . . . 357 ▫ Jack Location . . . . . . . . . . . . . . . . . . . . . . . .
WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER To engage the Hazard Warning Flashers, depress the switch on the instrument panel. When the Hazard Warning Switch is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency. Push the switch a second time to turn off the flashers. CAUTION! Hazard Flasher Switch The hazard flasher switch is located in the center of the instrument panel above the center air outlets.
WHAT TO DO IN EMERGENCIES 345 NOTE: With extended use, the Hazard Warning Flashers may wear down your battery. IF YOUR ENGINE OVERHEATS In any of the following situations, you can reduce the potential for overheating by taking the appropriate action. • On the highways — Slow down. • In city traffic — While stopped, put transmission in neutral, but do not increase engine idle speed. NOTE: There are steps that you can take to slow down an impending overheat condition.
WHAT TO DO IN EMERGENCIES WARNING! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call a service center if your vehicle overheats. If you decide to look under the hood yourself, see Section 7, Maintenance, of this manual. Follow the warnings under the Cooling System Pressure Cap paragraph.
WHAT TO DO IN EMERGENCIES 347 Remove the scissors jack and jack handle by rotating the small wing nut to the left. Six Passenger Seating The jack and jack-handle are stowed in the rear storage bin located in the rear cargo floor. Pull up on the storage bin cover and liner to access the jack and jack tools.
WHAT TO DO IN EMERGENCIES Spare Tire Stowage Five Passenger Seating The spare tire is stowed under the rear of the vehicle by means of a cable winch mechanism. To remove or stow the spare, use the jack handle to rotate the “spare tire drive” nut. The nut is located under the plastic cover at the center rear of the cargo floor area, just inside the liftgate opening. Six Passenger Seating The spare tire is stowed under the rear of the vehicle by means of a cable winch mechanism.
WHAT TO DO IN EMERGENCIES 349 CAUTION! WARNING! The winch mechanism is designed for use with the jack handle only. Use of an air wrench or other power tools is not recommended and can damage the winch. Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. When the spare is clear, tilt the retainer at the end of the cable and pull it through the center of the wheel.
WHAT TO DO IN EMERGENCIES Jacking Instructions WARNING! WARNING! Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: • Getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never get any part of your body under a vehicle that is on a jack. Never start or run the engine while the vehicle is on a jack.
WHAT TO DO IN EMERGENCIES 351 1. Remove the spare wheel, scissors jack and jack-handle from stowage. 2. Carefully pry off the wheel center cap if equipped, using the tip of the jack handle. 3. Loosen (but do not remove) the wheel lug nuts by turning them to the left one turn while the wheel is still on the ground. NOTE: Do not oil wheel studs. For chrome wheels, do not substitute with chrome plated wheel nuts. 4.
WHAT TO DO IN EMERGENCIES location. Do not raise the vehicle until you are sure the jack is securely engaged. Never jack up the vehicle using any suspension components. 7. Remove the wheel lug nuts, for vehicles with wheel covers, remove the cover from the wheel by hand. Do not pry the wheel cover off. Then pull the wheel off the hub. 6. Raise the vehicle by turning the jack screw to the right, using the swivel wrench.
WHAT TO DO IN EMERGENCIES 353 lug nuts until each nut has been tightened twice. Correct wheel nut tightness is 130 N·m (95 ft. lbs). If in doubt about the correct tightness, have them checked with a torque wrench by your dealer or at a service station. 11. Lower the jack to its fully closed position. WARNING! A loose tire or jack, thrown forward in a collision or hard stop could endanger the occupants of the vehicle. Always stow the jack parts and the spare tire in the places provided. 12.
WHAT TO DO IN EMERGENCIES NOTE: When reinstalling the wheel center cap, insure that the valve stem symbol on the back of the cap is pointed toward the wheel valve stem. Install the center cap using hand pressure only. Do not use a hammer. Wheel Nuts All wheel nuts should be tightened occasionally to eliminate the possibility of wheel studs being sheared or the bolt holes in the wheels becoming elongated.
WHAT TO DO IN EMERGENCIES 355 Check the Battery Test Indicator (if equipped). If a light or bright colored dot is visible in the indicator (if equipped), DO NOT jump-start the battery. If the indicator (if equipped) is dark or shows a green dot, proceed as follows: 1. Wear eye protection and remove any metal jewelry such as watch bands or bracelets that might make an inadvertent electrical contact. 2.
WHAT TO DO IN EMERGENCIES WARNING! WARNING! Do not connect the cable to the negative post of the discharge battery. The resulting electrical spark could cause the battery to explode. During cold weather when temperatures are below freezing point, electrolyte in a discharged battery may freeze. Do not attempt jump starting because the battery could rupture or explode. The battery temperature must be brought up above freezing point before attempting jump start.
WHAT TO DO IN EMERGENCIES 357 WARNING! Fast spinning tires can be dangerous. Forces generated by excessive wheel speeds may cause tire damage or failure. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 35 mph (55 km/h) when you are stuck. And don’t let anyone near a spinning wheel, no matter what the speed. CAUTION! Racing the engine or spinning the wheels too fast may lead to transmission overheating and failure. It can also damage the tires.
WHAT TO DO IN EMERGENCIES and rear wheels must be on the ground. If your vehicle must be towed farther or at a higher rate of speed, it must be transported on a flat bed truck. All Transmissions CAUTION! • Do not attempt to tow this vehicle from the front with sling type towing equipment. Damage to the front fascia will result. • Always use wheel lift equipment when towing from the front. The only other approved method of towing is with a flat bed truck. • Do not tow the vehicle from the rear.
WHAT TO DO IN EMERGENCIES 359 TOWING THIS VEHICLE BEHIND ANOTHER VEHICLE WITH A TOW DOLLY The manufacturer does not recommend that you tow an All-Wheel Drive (AWD) or front wheel drive vehicle on a tow dolly. Vehicle damage may occur.
MAINTAINING YOUR VEHICLE CONTENTS 䡵 4.0L Engines . . . . . . . . . . . . . . . . . . . . . . . . . . 364 ▫ Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . 369 䡵 3.8L Engines . . . . . . . . . . . . . . . . . . . . . . . . . . 365 ▫ Engine Oil Filter . . . . . . . . . . . . . . . . . . . . . . 374 䡵 Onboard Diagnostic System — OBD II . . . . . . . . 366 ▫ Drive Belts — Check Condition And Tension . . 374 ▫ Loose Fuel Filler Cap Message . . . . . . . . . . . . 366 ▫ Spark Plugs . . . . .
MAINTAINING YOUR VEHICLE ▫ Front & Rear Suspension Ball Joints . . . . . . . . 380 ▫ Automatic Transmission . . . . . . . . . . . . . . . . 392 ▫ Steering Shaft Seal . . . . . . . . . . . . . . . . . . . . 380 ▫ All Wheel Drive (AWD) — If Equipped . . . . . 395 ▫ Steering Linkage . . . . . . . . . . . . . . . . . . . . . . 380 ▫ Front And Rear Wheel Bearings . . . . . . . . . . . 396 ▫ Drive Shaft Universal Joints . . . . . . . . . . . . . . 380 ▫ Appearance Care And Protection From Corrosion .
MAINTAINING YOUR VEHICLE 363 ▫ Front Park/Turn Signal And Sidemarker Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 408 ▫ Front Fog Light . . . . . . . . . . . . . . . . . . . . . . 409 ▫ Rear Tail, Stop, Turn Signal, Side Marker And Back-Up Lights . . . . . . . . . . . . . . . . . . . . . . . 409 䡵 Fluids And Capacities . . . . . . . . . . . . . . . . . . . 411 䡵 Fluids, Lubricants And Genuine Parts . . . . . . . . 412 ▫ Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 4.0L ENGINES Engine Compartment 4.
MAINTAINING YOUR VEHICLE 365 3.8L ENGINES 7 Engine Compartment 3.
MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
MAINTAINING YOUR VEHICLE 367 cap until a ⬙clicking⬙ sound is heard. This is an indication that the gas cap is properly tightened. Press the odometer reset button to turn the message off. If the problem persists, the message will appear the next time the vehicle is started. This might indicate a damaged cap. If the problem is detected twice in a row, the system will turn on the Malfunction Indicator Light (MIL). Resolving the problem will turn the MIL light off.
MAINTAINING YOUR VEHICLE 4. As soon as you turn your key to the ON position, you will see your MIL symbol come on as part of a normal bulb check. 5. Approximately 15 seconds later, one of two things will happen: a. The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition key or start the engine. This means that your vehicle’s OBD system is not ready and you should not proceed to the I/M station. b.
MAINTAINING YOUR VEHICLE 369 DEALER SERVICE Your dealer has the qualified service personnel, special tools, and equipment to perform all service operations in an expert manner. Service Manuals are available which include detailed service information for your vehicle. Refer to these manuals before attempting any procedure yourself. NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you.
MAINTAINING YOUR VEHICLE The best time to check the engine oil level is about 5 minutes after a fully warmed engine is shut off or before starting the engine after it has sat overnight. Checking the oil while the vehicle is on level ground will improve the accuracy of the oil level readings. Maintain the oil level between the MIN and MAX markings on the dipstick. Adding one quart of oil when the reading is at the MIN mark will result in a MAX reading on these engines.
MAINTAINING YOUR VEHICLE 371 Change Engine Oil Road conditions and your kind of driving affects the interval at which your oil should be changed. Check the following list to see if any apply to you. NOTE: If ANY of these apply to you then change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first and follow schedule “B” of the ⬙Maintenance Schedules⬙ section of this manual. • Day or night temperatures are below 32°F (0°C).
MAINTAINING YOUR VEHICLE American Petroleum Institute (API) Engine Oil Identification Symbol This symbol means that the oil has been certified by the American Petroleum Institute (API). The manufacturer only recommends API Certified engine oils. Engine Oil Viscosity (SAE Grade) — 4.0 Liter Engines The proper SAE viscosity grade of engine oil should be selected based on the following recommendation and be within the operating temperature shown in the engine oil viscosity chart.
MAINTAINING YOUR VEHICLE 373 Engine Oil Viscosity (SAE Grade) — 3.8 Liter Engines SAE 5W-20 engine oil is recommended for all operating temperatures. This engine oil improves low temperature starting and vehicle fuel economy. Your engine oil filler cap also shows the recommended engine oil viscosity for your vehicle. For information on engine oil filler cap location, refer to the Engine Compartment illustration in this section.
MAINTAINING YOUR VEHICLE Engine Oil Filter The engine oil filter should be replaced at every engine oil change. Engine Oil Filter Selection This manufacture’s engines have a full-flow type oil filter. Use a filter of this type for replacement. The quality of replacement filters varies considerably. Only high quality filters should be used to assure most efficient service. Mopar Engine Oil Filters are a high quality oil filter and are recommended.
MAINTAINING YOUR VEHICLE 375 WARNING! The air cleaner can provide a measure of protection in the case of engine backfire. Do not remove the air cleaner unless such removal is necessary for repair or maintenance. Make sure that no one is near the engine compartment before starting the vehicle with the air cleaner removed. Failure to do so can result in serious personal injury. Catalytic Converter The catalytic converter requires the use of unleaded fuel only.
MAINTAINING YOUR VEHICLE NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you. WARNING! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your exhaust system. Do not park or operate your vehicle in areas where your exhaust system can contact anything that can burn.
MAINTAINING YOUR VEHICLE 377 WARNING! CAUTION! • Battery fluid is a corrosive acid solution and can burn or even blind you. Don’t allow battery fluid to contact your eyes, skin or clothing. Don’t lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area immediately with large amounts of water. • Battery gas is flammable and explosive. Keep flame or sparks away from the battery.
MAINTAINING YOUR VEHICLE Air Conditioner Maintenance For best possible performance, your air conditioner should be checked and serviced by an Authorized Dealer at the start of each warm season. This service should include cleaning of the condenser fins and a system performance check. Drive belt tension should also be checked at this time. WARNING! • Use only refrigerants and compressor lubricants approved by the manufacturer for your air conditioning system.
MAINTAINING YOUR VEHICLE 379 Refrigerant Recovery And Recycling R-134a Air Conditioning Refrigerant is a hydrofluorocarbon (HFC) that is endorsed by the Environmental Protection Agency and is an ozone-saving product. However, the manufacturer recommends that air conditioning service be performed by dealers or other service facilities using recovery and recycling equipment. NOTE: Use only manufacturer approved A/C System Sealers, Stop Leak Products, Seal Conditioners, Compressor Oil, or Refrigerants.
MAINTAINING YOUR VEHICLE WARNING! Fluid level should be checked on a level surface and with the engine off to prevent injury from moving parts and to insure accurate fluid level reading. Do not overfill. Use only manufacturers recommended power steering fluid. If necessary, add fluid to restore to the proper indicated level. With a clean cloth, wipe any spilled fluid from all surfaces. Refer to Fluids, Lubricants, and Genuine Parts for correct fluid type.
MAINTAINING YOUR VEHICLE 381 Continued operation could result in failure of the universal joint due to water and dirt contamination of the grease. This would require complete replacement of the joint assembly. The external lock cylinders should be lubricated twice a year, preferably in the fall and spring. Apply a small amount of a high quality lubricant such as Mopar威 Lock Cylinder Lubricant directly into the lock cylinder.
MAINTAINING YOUR VEHICLE Windshield and Rear Window Washers The fluid reservoir for the windshield washers and the rear window washer is shared. It is located in the engine compartment and should be checked for fluid level at regular intervals. Fill the reservoir with windshield washer solvent (not radiator antifreeze) and operate the system for a few seconds to flush out the residual water. The washer fluid reservoir will hold a full gallon of fluid when the Low Washer Fluid Light illuminates.
MAINTAINING YOUR VEHICLE 383 vehicle, or when the underside or rear of the vehicle is damaged, have a competent mechanic inspect the complete exhaust system and adjacent body areas for broken, damaged, deteriorated, or mispositioned parts. Open seams or loose connections could permit exhaust fumes to seep into the passenger compartment. In addition, inspect the exhaust system each time the vehicle is raised for lubrication or oil change. Replace as required. WARNING! Exhaust gases can injure or kill.
MAINTAINING YOUR VEHICLE Engine Coolant Checks Check the engine coolant (antifreeze) protection every 12 months (before the onset of freezing weather, where applicable). If coolant is dirty or rusty in appearance, the system should be drained, flushed and refilled with fresh coolant. Check the front of the A/C condenser for any accumulation of bugs, leaves, etc. If dirty, clean by gently spraying water from a garden hose vertically down the face of the condenser.
MAINTAINING YOUR VEHICLE 385 CAUTION! Mixing of coolants other than specified HOAT engine coolants, may result in engine damage and may decrease corrosion protection. If a non-HOAT coolant is introduced into the cooling system in an emergency, it should be replaced with the specified coolant as soon as possible. Do not use plain water alone or alcohol base engine coolant (antifreeze) products.
MAINTAINING YOUR VEHICLE The use of lower quality water will reduce the amount of corrosion protection in the engine cooling system. Please note that it is the owner’s responsibility to maintain the proper level of protection against freezing according to the temperatures occurring in the area where the vehicle is operated. NOTE: Mixing coolant types will decrease the life of the engine coolant and will require more frequent coolant changes.
MAINTAINING YOUR VEHICLE 387 do not store ethylene glycol based engine coolant in open containers or allow it to remain in puddles on the ground. If ingested by a child, contact a physician immediately. Clean up any ground spills immediately. Engine Coolant Level The coolant bottle provides a quick visual method for determining that the coolant level is adequate. With the engine off and cold, the coolant level in the coolant recovery bottle should be between the ranges indicated on the bottle.
MAINTAINING YOUR VEHICLE • Check coolant freeze point in the radiator and in the coolant recovery bottle. If antifreeze needs to be added, contents of coolant recovery bottle must also be protected against freezing. • If frequent coolant additions are required, or if the level in the coolant recovery bottle does not drop when the engine cools, the cooling system should be pressure tested for leaks.
MAINTAINING YOUR VEHICLE 389 Inspect all hose connections such as clamps and couplings to make sure they are secure and no leaks are present. Components should be replaced immediately if there is any evidence of wear or damage that could cause failure. Brakes In order to assure brake system performance, all brake system components should be inspected periodically. Suggested service intervals can be found in the Maintenance Schedules.
MAINTAINING YOUR VEHICLE hot fluid when systems are under pressure (during vehicle operation), should be noted before a hose is replaced based on leakage. NOTE: Inspection of brake hoses should be performed whenever the brake system is serviced and at every engine oil change. Inspect hydraulic brake hoses for surface cracking, scuffing, or worn spots.
MAINTAINING YOUR VEHICLE 391 WARNING! CAUTION! • Overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts and the brake fluid catching fire. • Use of brake fluid that may have a lower initial boiling point or unidentified as to specification, may result in sudden brake failure during hard prolonged braking. You could have an accident.
MAINTAINING YOUR VEHICLE Care should be taken in installing quick connect fittings to insure they are properly installed and fully connected. See your authorized dealer for service. for correct fluid type. It is important that the transmission fluid be maintained at the prescribed level using the recommended fluid. Automatic Transmission The automatic transmission and differential assembly are contained within a single housing.
MAINTAINING YOUR VEHICLE 393 3. Fully apply parking brake. 4. Place the gear selector momentarily in each gear position ending with the lever in P (PARK). Wipe the area around the dipstick clean to eliminate the possibility of dirt entering the transmission. Procedure For Checking Fluid Level The fluid level in the automatic transmission should be checked whenever the vehicle is serviced. Operation with an improper fluid level will greatly reduce the life of the transmission and of the fluid.
MAINTAINING YOUR VEHICLE b. If the fluid is cold, the fluid level should be between the lower two holes in the area marked “COLD”. If the fluid level indicates low, add sufficient fluid to bring to the proper level. CAUTION! Do not overfill. Dirt and water in the transmission can cause serious damage. To prevent dirt and water from entering the transmission after checking or replenishing fluid, make certain that the dipstick cap is reseated properly.
MAINTAINING YOUR VEHICLE 395 All Wheel Drive (AWD) — If Equipped Under normal operating conditions, periodic fluid level checks and lubricant changes for the Power Transfer Unit and Rear Carrier, are not required. However when the vehicle is serviced for other reasons, the exterior surface of these components should be inspected for evidence of fluid leaks. Confirmed leaks should be repaired as soon as possible. Rear Carrier The fill plug is located on the side of the rear carrier housing.
MAINTAINING YOUR VEHICLE Severe Usage is defined as: Appearance Care and Protection from Corrosion 1. More than 50% of vehicle operation in stop and go traffic where vehicle is driven regularly for more than 45 minutes of continuous operation, such as in heavy city or in construction zone traffic, Protection of Body and Paint from Corrosion Vehicle body care requirements vary according to geographic locations and usage.
MAINTAINING YOUR VEHICLE 397 The most common causes are: • Road salt, dirt and moisture accumulation. • Stone and gravel impact. • Insects, tree sap and tar. • Salt in the air near seacoast localities. • Use Mopar Cleaner Wax to remove road film, stains and to protect your paint finish. Take care never to scratch the paint. • Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish. • Atmospheric fallout/industrial pollutants.
MAINTAINING YOUR VEHICLE • It is important that the drain holes in the lower edges of the doors, rocker panels and trunk be kept clear and open. • Use Mopar touch up paint on scratches as soon as possible. Your dealer has touch up paint to match the color of your vehicle. • If you detect any stone chips or scratches in the paint, touch them up immediately. The cost of such repairs is considered the responsibility of the owner.
MAINTAINING YOUR VEHICLE 399 Interior Care Cleaning Interior Fabric Upholstery Your interior seat Yes Essentials™ fabric upholstery should be cleaned in the following manner: • Remove as much of the stain as possible by blotting with a clean, dry towel. • Blot any remaining stain with a clean, damp towel. • For tough stains in fabrics, apply Mopar Total Clean to a clean cloth and remove stain. Use a fresh, damp towel to remove soap residue.
MAINTAINING YOUR VEHICLE upholstery. Application of a leather conditioner is not required to maintain the original condition. When cleaning the rear view mirror, spray cleaner on the towel or rag that you are using. Do not spray cleaner directly on the mirror. WARNING! Cleaning Plastic Instrument Cluster Lenses The lenses in front of the instruments in this vehicle are molded in clear plastic. When cleaning the lenses, care must be taken to avoid scratching the plastic.
MAINTAINING YOUR VEHICLE 401 Seat Belt Maintenance Do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage can also weaken the fabric. If the belts need cleaning, use a mild soap solution or lukewarm water. Do not remove the belts from the car to wash them. Replace the belts if they appear frayed or worn or if the buckles do not work properly.
MAINTAINING YOUR VEHICLE FUSES (INTEGRATED POWER MODULE) Cavity 1 2 3 4 5 6 Integrated Power Module (IPM) An Integrated Power Module (IPM) is located in the engine compartment near the battery. This center contains maxi fuses, mini fuses and relays. A label that identifies each component is printed on the inside of the cover.
MAINTAINING YOUR VEHICLE 403 Cavity 9 10 11 12 13 14 15 40 41 Cartridge Fuse 40 Amp Green Spare 40 Amp Green Spare 40 Amp Green Spare 40 Amp Green 40 Amp Green 40 Amp Green Description Cavity Power Sunroof 42 Headlight Washer, Power Liftgate Cavity 24 Radiator Fan 1 25 Anti-Lock Brake System (ABS) Module Driver Door Node 26 Passenger Door Node 27 28 Cartridge Fuse 40 Amp Green Description Front Blower Mini Fuse Description 20 Amp Yel- Power Outlet (Selectable) low 15 Amp Blue Radio, Amplifi
MAINTAINING YOUR VEHICLE Cavity 29 Mini Fuse 20 Amp Yellow 30 31 10 Amp Red 20 Amp Yellow Spare Spare 20 Amp Yellow 25 Amp Natural 20 Amp Yellow 20 Amp Yellow 34 35 36 37 38 39 Description Cluster, CHMSL, Stop Lights, Anti-Lock Brake System (ABS) Ignition Switch Hazard Cavity 44 45 46 47 Electronic Automatic Transaxle (EATX) Solenoid ASD 48 Fuel Pump 49 A/C Clutch, MTV 50 Mini Fuse 25 Amp Natural 10 Amp Red Description Rear Heated Seats Anti-Lock Brake System (ABS) Ignition Run Passenger
MAINTAINING YOUR VEHICLE 405 CAUTION! • When installing the Integrated Power Module cover, it is important to ensure the cover is properly positioned and fully latched. Failure to do so may allow water to get into the Integrated Power Module, and possibly result in a electrical system failure. • When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating. The use of a fuse with a rating other than indicated may result in a dangerous electrical system overload.
MAINTAINING YOUR VEHICLE REPLACEMENT LIGHT BULBS LIGHT BULBS — Interior Bulb Number Center & Rear Reading Lights . . . . . . . . . . . . . . . 578 Front Door Courtesy Light . . . . . . . . . . . . . . . . . . 578 Liftgate Light(s). . . . . . . . . . . . . . . . . . . . . . . . . . 578 Overhead Console Reading Lights . . . . . . . . . . . 212–2 Visor Vanity Lights. . . . . . . . . . . . . . . . . . . . . V26377 NOTE: For lighted switches, see your dealer for replacement instructions.
MAINTAINING YOUR VEHICLE 407 CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with an oily surface, clean the bulb with rubbing alcohol. 2. Disconnect the electrical connector. 3. Remove the rubber boot seals. 4. Rotate the bulb to the left and replace the bulb. Reinstall the rubber boot seals and then the headlight module.
MAINTAINING YOUR VEHICLE WARNING! A transient high tension occurs at the bulb sockets of High Intensity Discharge (HID) headlights when the headlight switch is turned ON. It may cause serious electrical shock or electrocution if not serviced properly. See your authorized dealer for service. NOTE: On vehicles equipped with High Intensity Discharge Headlights (HID), when the headlights are turned on there is a blue hue to the lights.
MAINTAINING YOUR VEHICLE 409 Front Fog Light 1. Reach under the front fascia and grasp the front fog light bulb. 2. Twist the front fog light bulb to remove from the fog light module. 3. Disconnect the electrical connector and replace the bulb. Rear Tail, Stop, Turn Signal, Side Marker and Back-up Lights 1. Raise the liftgate. 2. Remove the two tail light assembly screws and rotate the assembly outward to remove the ball stud form the attaching grommet.
MAINTAINING YOUR VEHICLE 3. Twist the socket assembly to remove it from the housing. License Light 4. Pull the bulb out of the socket. 1. Place a screwdriver in the slot next to the release tab and push on the release tab to remove the lens. 5. Replace the bulb, reinstall the socket, and reattach the tail light assembly. 2. Pull the bulb out of the socket. Replace the bulb and push on the lens until it snaps into place.
MAINTAINING YOUR VEHICLE 411 FLUIDS AND CAPACITIES Fuel Engine Oil-With Filter 4.0 Liter Engines (SAE 10W-30, API Certified) 3.8 Liter Engines (SAE 5W-20, API Certified) U.S. 23 gallons Metric 87 liters 5.5 qts 5.0 qts 5.2 liters 4.7 liters 10.7 qts 10.1 liters 11.8 qts 11.2 liters Cooling System * 4.0 Liter Engines (Mopar威 Antifreeze/Coolant 5 Year/ 100,000 Mile Formula or equivalent) 3.
MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant 4.0 Liter Engine Oil 3.8 Liter Engine Oil Spark Plugs Oil Filter, 4.0/3.8 Liter Engines Fuel Selection Fluids, Lubricants and Genuine Parts Mopar威 Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) or equivalent Use API Certified SAE 10W-30 engine oil, refer to oil viscosity chart for correct SAE grade meeting DaimlerChrysler Material Standard MS-6395.
MAINTAINING YOUR VEHICLE 413 Chassis Component Automatic Transmission AWD Power Transfer Unit AWD Rear Carrier Brake Master Cylinder Power Steering Reservoir Fluids, Lubricants and Genuine Parts Mopar威 ATF+4 Automatic Transmission Fluid. Mopar威 Gear Lubricant 75W-90 or equivalent. Mopar威 Gear Lubricant 75W-90 or equivalent. Mopar威 DOT 3 and SAE J1703 should be used. Use only recommended brake fluids. Mopar威Power Steering Fluid +4 or Mopar威ATF +4 Automatic Transmission Fluid.
MAINTENANCE SCHEDULES CONTENTS M A I N T E N A N C E 䡵 Emission Control System Maintenance . . . . . . . . 416 ▫ Schedule “B” . . . . . . . . . . . . . . . . . . . . . . . . 419 䡵 Maintenance Schedules . . . . . . . . . . . . . . . . . . . 416 ▫ Schedule “A” . . . . . . . . . . . . . . . . . . . . . . . .
M A I N T E N A N C E 416 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
MAINTENANCE SCHEDULES 417 M • Taxi, police, or delivery service (commercial service).〫 • Off-road or desert operation. NOTE: If ANY of these apply to you then change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first and follow schedule “B” of the ⬙Maintenance Schedules⬙ section of this manual. NOTE: Most vehicles are operated under the conditions listed for Schedule ⬙B⬙. Second is Schedule “A”.
M A I N T E N A N C E S C H E D U L E S 8 418 MAINTENANCE SCHEDULES Once a Month At Each Oil Change • Check tire pressure and look for unusual wear or damage. • Change the engine oil filter. • Inspect the battery and clean and tighten the terminals as required. • Check the fluid levels of coolant bottle, brake master cylinder and transmission, add as needed. • Check all lights and all other electrical items for correct operation. • Inspect the exhaust system. • Inspect the brake hoses.
SCHEDULE “B” SCHEDULE “B” Follow schedule “B” if you usually operate your vehicle under one or more of the following conditions. Change the automatic transmission fluid and filter every 60,000 miles (96 000 km) if the vehicle is usually operated under one or more of the conditions marked with an 〫. • Day or night temperatures are below 32° F (0° C). • Stop and go driving. • Extensive engine idling. • Driving in dusty conditions. • Short trips of less than 10 miles (16 km).
M 420 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter. A Rotate Tires N C Inspect the brake linings. E Inspect the engine air cleaner filter, replace if S C H E D U L E S 8 necessary. * Replace the engine air cleaner filter. * Change the All Wheel Drive (AWD) power transfer unit fluid. (See note at the end of this chart) Replace the air conditioning filter.
SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Rotate Tires Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter. Inspect the tie rod ends and boot seals. (Front & Rear) Inspect the PCV valve and replace as necessary.* Change the All Wheel Drive (AWD) power transfer unit fluid. (See note at the end of this chart) Change the All Wheel Drive (AWD) rear carrier fluid.
M 422 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter. A Rotate Tires N C Inspect the brake linings. E Inspect the engine air cleaner filter, replace if S C H E D U L E S 8 necessary. * Replace the engine air cleaner filter. * Change the All Wheel Drive power transfer unit fluid. (See the note at the end of this chart.) Change the All Wheel Drive (AWD) rear carrier fluid. (See note at the end of this chart) Replace the air conditioning filter.
SCHEDULE “B” 423 M Miles 57, 000 60, 000 63, 000 66, 000 69, 000 72, 000 (Kilometers) (91 000) (96 000) (101 000) (106 000) (110 000) (115 000) Change engine oil and engine oil filter. X X X X X X Rotate Tires X X X Inspect the brake linings. X X Inspect the engine air cleaner filter, replace if necessary. * X X X X X Replace the engine air cleaner filter. X Inspect the tie rod ends and boot seals. (Front & Rear) X Inspect the PCV valve and replace if necessary.
M 424 SCHEDULE “B” A I 75, 000 78, 000 81, 000 84, 000 87, 000 90, 000 N Miles T (Kilometers) (120 000) (125 000) (130 000) (134 000) (139 000) (144 000) E X X X X X X N Change engine oil and engine oil filter. A Rotate Tires X X X N Inspect the brake linings. X X C E Inspect the engine air cleaner filter, replace if necessary. * X X X X S C H E D U L E S 8 Replace the engine air cleaner filter Replace the spark plugs. Inspect the tie rod ends and boot seals.
SCHEDULE “B” 425 M Miles 93, 000 96, 000 99, 000 100, 000 102, 000 105, 000 (Kilometers) (149 000) (154 000) (158 000) (160 000) (163 000) (168 000) Change engine oil and engine oil filter. X X X X X Rotate Tires X X Inspect the brake linings. X Inspect the engine air cleaner filter, replace if necessary. * X X X X Replace the engine air cleaner filter * X Replace engine timing belt. X Change the All Wheel Drive (AWD) power transfer unit X fluid.
M 426 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter. A Rotate Tires N C Inspect the brake linings. E Inspect the engine air cleaner filter, replace if necesS C H E D U L E S 8 sary. * Replace the engine air cleaner filter. Inspect the tie rod ends and boot seals. (Front & Rear) Inspect the PCV valve and replace as necessary.* Inspect the serpentine drive belt, replace if necessary. ‡ Change the automatic transmission fluid and filter.
SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Rotate Tires Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter. Inspect the serpentine drive belt, replace if necessary. ‡ Change the All Wheel Drive (AWD) power transfer unit fluid. (See note at the end of this chart) Change the All Wheel Drive (AWD) rear carrier fluid. (See note at the end of this chart) Replace the air conditioning filter.
M 428 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter. A Rotate Tires N C Inspect the brake linings. E Inspect the engine air cleaner filter, replace if necesS C H E D U L E S 8 sary. * Replace the engine air cleaner filter. Replace the spark plugs. Inspect the serpentine drive belt, replace if necessary. ‡ Inspect the tie rod ends and boot seals. (Front & Rear) Inspect the PCV valve and replace as necessary.* Change the All Wheel Drive (AWD) power transfer unit fluid.
SCHEDULE “B” 429 M A I Miles 138, 000 141, 000 144, 000 147, 000 150, 000 N T (Kilometers) (221 000) (226 000) (230 000) (235 000) (240 000) E Change the All Wheel Drive (AWD) rear carrier X N A fluid. (See note at the end of this chart) N Replace the air conditioning filter. X C * This maintenance is recommended by the manufacture NOTE: The AWD power transfer unit fluid and the E to the owner but is not required to maintain the emissions warranty.
M 430 SCHEDULE “A” A I SCHEDULE “A” N T Miles E N (Kilometers) A [Months] N C Change engine oil and engine oil filter. E Rotate Tires S C H E D U L E S 8 Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter. Inspect the tie rod ends and boot seals. (Front & Rear) Replace the air conditioning filter.
SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate Tires Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter. Inspect the tie rod ends and boot seals. (Front & Rear) Check the PCV valve and replace, if necessary.* Inspect the serpentine drive belt, replace if necessary. ‡ Flush and replace the engine coolant at 60 months or 100,000 miles, whichever occurs first.
M 432 SCHEDULE “A” A I N Miles T (Kilometers) E N [Months] A Change engine oil and engine oil filter. N C Rotate Tires E Inspect the brake linings. S C H E D U L E S 8 Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter. Inspect the tie rod ends and boot seals. (Front & Rear) Check and replace the PCV valve , if necessary.* Inspect the serpentine drive belt, replace if necessary. ‡ Replace the spark plugs.
SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate Tires Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter. Replace engine timing belt. Inspect the tie rod ends and boot seals. (Front & Rear) Check the PCV valve and replace, if necessary.* Inspect the serpentine drive belt, replace if necessary. ‡ Flush and replace the engine coolant at 120 months, if not done at 100,000 miles (160 000 km).
M 434 SCHEDULE “A” A I N Miles T (Kilometers) E N [Months] A Change engine oil and engine oil filter. N C Rotate Tires E Inspect the brake linings. S C H E D U L E S 8 Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter. Inspect the tie rod ends and boot seals. (Front & Rear) Check the PCV valve and replace, if necessary.* Inspect the serpentine drive belt, replace if necessary. ‡ Replace the air conditioning filter.
SCHEDULE “A” WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS 䡵 Suggestions For Obtaining Service For Your Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . 438 ▫ Prepare For The Appointment . . . . . . . . . . . . 438 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . . . 438 䡵 Reporting Safety Defects . . . . . . . . . . . . . . . . . . 441 ▫ In Canada . . . . . . . . . . . . . . . . . . . . . . . . . . 441 䡵 Publication Order Forms . . . . . . . . . . . . . . . . . . 442 ▫ Be Reasonable With Requests .
IF YOU NEED CONSUMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty, discuss additional charges with the service manager. Keep a maintenance log of your vehicle’s service history. This can often provide a clue to the current problem.
IF YOU NEED CONSUMER ASSISTANCE 439 technicians, special tools, and the latest information to assure your vehicle is fixed correctly and in a timely manner. This is why you should always talk to your dealer’s service manager first. Most matters can be resolved with this process. • If for some reason you are still not satisfied, talk to the general manager or owner of the dealership. They want to know if you need assistance.
IF YOU NEED CONSUMER ASSISTANCE Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommunication Devices for the Deaf) equipment at its Customer Center. Any hearing or speech impaired customer who has access to a TDD or a conventional teletypewriter (TTY) in the United States can communicate with the manufacturer by dialing 1–800–380–CHRY.
IF YOU NEED CONSUMER ASSISTANCE 441 WARRANTY INFORMATION (U.S. Vehicles Only) See the Warranty Information Booklet for the terms and provisions of DaimlerChrysler’s warranties applicable to this vehicle. MOPAR姞 PARTS Mopar威 fluids, lubricants, parts, and accessories are available from your dealer. They will help you keep your vehicle operating at its best. REPORTING SAFETY DEFECTS In the 50 United States and Washington D.C.
IF YOU NEED CONSUMER ASSISTANCE PUBLICATION ORDER FORMS To order the following manuals, you may use either the website or the phone numbers listed below. Visa, Mastercard, American Express, and Discover orders are accepted. If you prefer mailing your payment, please call for an order form. NOTE: A street address is required when ordering manuals. (No P.O. Boxes). • Service Manuals.
IF YOU NEED CONSUMER ASSISTANCE 443 Call Toll Free at: • 1–800–890–4038 (U.S.) • 1–800–387–1143 (Canada) Or Visit us on the World Wide Web at: • www.techauthority.daimlerchrysler.com • www.daimlerchrysler.ca/manuals DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES The following describes the tire grading categories established by the National highway Traffic Safety Administration.
IF YOU NEED CONSUMER ASSISTANCE WARNING! The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics. Temperature Grades The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel.
INDEX 10
INDEX Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 321 Adding Washer Fluid . . . . . . . . . . . . . . . . . . 140,382 Additives, Fuel . . . . . . . . . . . . . . . . . . . . . . . . . 320 Adjustable Pedals . . . . . . . . . . . . . . . . . . . . . . . 148 Air Conditioner Maintenance . . . . . . . . . . . . . . . 378 Air Conditioning . . . . . . . . . . . . . . . . . . . . . 241,246 Air Conditioning Controls . . . . . . . . . . . . . . . . . 241 Air Conditioning Filter . . . . . .
INDEX 447 Selection Of Lubricant . . . . . . . . . . . . . . . . 392,413 Shifting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 272 Special Additives . . . . . . . . . . . . . . . . . . . . . . 394 Automatic Transmission . . . . . . . . . . . . . . . . . . . 392 Adding Fluid . . . . . . . . . . . . . . . . . . . . . . . . . 393 Fluid and Filter Changes . . . . . . . . . . . . . . . . . 394 Fluid Change . . . . . . . . . . . . . . . . . . . . . . . . . 394 Fluid Level Check . . . . . . . . . . .
INDEX Radiator (Coolant Pressure) . . . . . . . . . . . . . . . 386 Car Washes . . . . . . . . . . . . . . . . . . . . . . . . . . . . 397 Carbon Monoxide Warning . . . . . . . . . . . . . . . . . 321 Cargo Area Cover . . . . . . . . . . . . . . . . . . . . . . . 167 Cargo Compartment Luggage Carrier . . . . . . . . . . . . . . . . . . . . . . . 169 Cargo Tie-Downs . . . . . . . . . . . . . . . . . . . . . . . . 168 Cassette Tape and Player Maintenance . . . . . . . . . 239 Catalytic Converter . . . .
INDEX 449 Coolant Pressure Cap (Radiator Cap) . . . . . . . . . . 386 Cooling System . . . . . . . . . . . . . . . . . . . . . . . . . 383 Adding Coolant (Antifreeze) . . . . . . . . . . . . . . 385 Coolant Capacity . . . . . . . . . . . . . . . . . . . . . . 411 Coolant Level . . . . . . . . . . . . . . . . . . . . . . 384,387 Disposal of Used Coolant . . . . . . . . . . . . . . . . 386 Drain, Flush, and Refill . . . . . . . . . . . . . . . . . . 384 Inspection . . . . . . . . . . . . . . . . . . . . . .
INDEX Driving On Slippery Surfaces . . . . . . . . . . . . . . . . . . . . 287 DVD Player (Video Entertainment System) . . . . . . 221 E-85 Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 324 Electric Remote Mirrors . . . . . . . . . . . . . . . . . . . . 90 Electrical Power Outlets . . . . . . . . . . . . . . . . . . . 163 Electronic Speed Control (Cruise Control) . . . . . . 150 Electronic Vehicle Information Center (EVIC) . 146,191 Emergency, In Case of Hazard Warning Flasher . . . .
INDEX 451 Exhaust System . . . . . . . . . . . . . . . . . . . . . . . . . 382 Extender, Seat Belt . . . . . . . . . . . . . . . . . . . . . . . . 49 Exterior Folding Mirrors . . . . . . . . . . . . . . . . . . . 89 Filters Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . 374 Air Conditioning . . . . . . . . . . . . . . . . . . . . 259,379 Automatic Transaxle . . . . . . . . . . . . . . . . . . . . 394 Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . 374,412 Engine Oil Disposal . .
INDEX Filler Cap (Gas Cap) . . . . . . . . . . . . . . . . . . . . 321 Gasoline . . . . . . . . . . . . . . . . . . . . . . . . . . . . 318 Gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181 Hoses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 391 Octane Rating . . . . . . . . . . . . . . . . . . . . . . 318,412 Requirements . . . . . . . . . . . . . . . . . . . . . . 318,411 Tank Capacity . . . . . . . . . . . . . . . . . . . . . . . . 411 Fuel, Flexible . . . . . . . .
INDEX 453 Replacing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 406 Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135 Time Delay . . . . . . . . . . . . . . . . . . . . . . . . . . 136 Heated Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . 116 Heater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 241 Heater, Engine Block . . . . . . . . . . . . . . . . . . . . . 270 Hitches Trailer Towing . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Key-In Reminder . . . Keyless Entry System Keys . . . . . . . . . . . Knee Bolster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 20 12 55 Lap/Shoulder Belts . . . . . . . . . . . . . . . . . . . . . . . 41 LATCH (Lower Anchors and Tether for CHildren) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71,74 Latches Hood . . .
INDEX 455 Oil Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . 186 Park . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 408 Reading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153 Rear Servicing . . . . . . . . . . . . . . . . . . . . . . . . 409 Rear Tail . . . . . . . . . . . . . . . . . . . . . . . . . . . . 409 Seat Belt Reminder . . . . . . . . . . . . . . . . . . . . . 186 Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88 Automatic Dimming . . . . . . . . . . . . . . . . . . . . . 88 Electric Remote . . . . . . . . . . . . . . . . . . . . . . . . 90 Exterior Folding . . . . . . . . . . . . . . . . . . . . . . . . 89 Heated . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91 Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127 Outside . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 Rearview . . . . .
INDEX 457 Owner’s Manual (Operator Manual) . . . . . . . . . . 442 Panic Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Parking Brake . . . . . . . . . . . . . . . . . . . . . . . . . . 276 Parking On Hill . . . . . . . . . . . . . . . . . . . . . . . . . 277 Passing Light . . . . . . . . . . . . . . . . . . . . . . . . . . . 138 Pedals, Adjustable . . . . . . . . . . . . . . . . . . . . . . . 148 Pets, Transporting . . . . . . . . . . . . . . . . . . . . . . . . 78 Phone, Cellular . . .
INDEX Rear Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . 146 Rear Liftgate . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Rear Seating Flexibility . . . . . . . . . . . . . . . . . . . . 124 Rear Window Defroster . . . . . . . . . . . . . . . . . . . 259 Rear Window Features . . . . . . . . . . . . . . . . . . . . 139 Rear Wiper/Washer . . . . . . . . . . . . . . . . . . . . . . 139 Rearview Mirrors . . . . . . . . . . . . . . . . . . . . . . . . 88 Reclining Front Seats . .
INDEX 459 Adjustable Shoulder Belt . . . . . . . . . . . . . . . . . . 46 Adjustable Upper Shoulder Anchorage . . . . . . . . 46 And Pregnant Women . . . . . . . . . . . . . . . . . . . 49 Child Restraint . . . . . . . . . . . . . . . . . . . . . . . 67,69 Extender . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Front Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Pretensioners . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Rear Seat . . . . . . . . . . . . . . . . . .
INDEX Engine Fails to Start . . . . . . . . . . . . . . . . . . . . 268 Starting and Operating . . . . . . . . . . . . . . . . . . . . 266 Starting Procedures . . . . . . . . . . . . . . . . . . . . . . 266 Steering Linkage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 380 Power . . . . . . . . . . . . . . . . . . . . . . . . . . . 286,379 Shaft Seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . 380 Tilt Column . . . . . . . . . . . . . . . . . . . . . . . . . . 141 Wheel Lock . .
INDEX 461 Compact Spare . . . . . . . . . . . . . . . . . . . . . . . . 301 General Information . . . . . . . . . . . . . . . . . . . . 297 High Speed . . . . . . . . . . . . . . . . . . . . . . . . . . 299 Inflation Pressures . . . . . . . . . . . . . . . . . . . . . 298 Jacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 346 Life of Tires . . . . . . . . . . . . . . . . . . . . . . . . . . 304 Load Capacity . . . . . . . . . . . . . . . . . . . . . 293,294 Pressure Monitor System (TPMS) . .
INDEX Overdrive . . . . . . . . . . . . . . . . . . . . . . . . . . . 274 Selection of Lubricant . . . . . . . . . . . . . . . . 392,413 Transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . 392 Automatic . . . . . . . . . . . . . . . . . . . . . . . . . . . 392 Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 394 Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 392 Transmitter Battery Service (Remote Keyless Entry) .
INDEX 463 Washers, Windshield . . . . . . . . . . . . . . . . . . . . . 138 Washing Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . 397 Wheel Alignment and Balance . . . . . . . . . . . . . . . 305 Wheel and Wheel Trim . . . . . . . . . . . . . . . . . . . . 398 Wheel and Wheel Trim Care . . . . . . . . . . . . . . . . 398 Wheel Bearings . . . . . . . . . . . . . . . . . . . . . . . . . 396 Wheel Nut Torque . . . . . . . . . . . . . . . . . . . . . . . 354 Wind Buffeting . . . . . . . . . . . . .
NOTES
