SECTION TABLE OF CONTENTS PAGE 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 2 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 3 4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION CONTENTS 䡵 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 Vehicle Identification Number . . . . . . . . . . . . . . 6 䡵 How To Use This Manual . . . . . . . . . . . . . . . . . 4 䡵 Vehicle Modifications / Alterations . . . . . . . . . . 6 䡵 Warnings And Cautions . . . . . . . . . . . . . . . . . .
INTRODUCTION INTRODUCTION This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a Warranty Information Booklet and various customer oriented documents. You are urged to read these publications carefully. Following the instructions and recommendations in this manual will help assure safe and enjoyable operation of your vehicle.
INTRODUCTION 5 1 Common Icons
INTRODUCTION WARNINGS AND CAUTIONS This manual contains WARNINGS against operating procedures, which could result in an accident or bodily injury. It also contains CAUTIONS against procedures, which could result in damage to your vehicle. If you do not read this entire manual you may miss important information. Observe all Warnings and Cautions. VEHICLE IDENTIFICATION NUMBER Vehicle Identification Number (VIN) is found on the driver’s front corner of the instrument panel, visible through the windshield.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS 䡵 A Word About Your Keys . . . . . . . . . . . . . . . . .10 ▫ To Arm The System . . . . . . . . . . . . . . . . . . . . .14 ▫ Ignition Key Removal . . . . . . . . . . . . . . . . . . .10 ▫ To Disarm The System . . . . . . . . . . . . . . . . . . .15 ▫ Automatic Transaxle Ignition Interlock System . . . . . . . . . . . . . . . . . . . . . . .11 ▫ Security System Manual Override . . . . . . . . . . .16 ▫ Key-In-Ignition Reminder . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ To Program Transmitters . . . . . . . . . . . . . . . . .20 ▫ Reset Express Up . . . . . . . . . . . . . . . . . . . . . .29 ▫ General Information . . . . . . . . . . . . . . . . . . . .20 ▫ Wind Buffeting . . . . . . . . . . . . . . . . . . . . . . . .29 ▫ Battery Replacement . . . . . . . . . . . . . . . . . . . .20 䡵 Trunk Release . . . . . . . . . . . . . . . . . . . . . . . . . .29 䡵 Remote Start System — If Equipped . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 9 ▫ Airbag System Components . . . . . . . . . . . . . . .41 䡵 Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . .64 ▫ Front Seat Airbag Features . . . . . . . . . . . . . . . .42 ▫ Exhaust Gas . . . . . . . . . . . . . . . . . . . . . . . . . .64 ▫ Airbag Deployment Sensors And Controls . . . . .47 ▫ Safety Checks You Should Make Inside The Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . .64 ▫ Event Data Recorder (EDR) . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS The dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys from your dealer. Ask your dealer for these numbers and keep them in a safe place. Vehicle Key Ignition Key Removal Automatic Transaxle Place the shift lever in PARK.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ignition cylinder to warn you that this safety feature is inoperable. The engine can be started and stopped but the key cannot be removed until you obtain service. NOTE: The power window switches, radio, and power outlets, will remain active for up to 45 seconds after the ignition switch has been turned off. Opening a vehicle front door will cancel this feature. WARNING! NEVER leave children alone in a vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Locking Doors With The Key There is only one external door lock cylinder which is located in the driver’s door only. immediately after the ignition switch is turned on for a bulb check. Afterwards, if the bulb remains on, this indicates a problem with the electronics. You can insert the key with either side up. To lock the door, turn the key rearward, to unlock the door, turn the key forward. See Section 7 of this manual for door lock lubrication.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Exxon/Mobil Speed Pass,™ additional Sentry Keys, or any other transponder equipped components on the same keychain will not cause a key-related (transponder) fault unless the additional part is physically held against the ignition key being used when starting the vehicle. Cell phones, pagers, or other RF electronics will not cause interference with this system. All of the keys provided with your new vehicle have been programmed to the vehicle electronics.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Insert a blank Sentry Key into the ignition switch and turn the ignition switch ON within 60 seconds. After 10 seconds a single chime will sound. The Theft Alarm Light will stop flashing, turn on for 3 seconds; then turn off. SECURITY ALARM SYSTEM — IF EQUIPPED The Vehicle Theft Security Alarm (VTSA) system monitors the doors, trunk, and ignition switch for unauthorized operation. The new Sentry Key has been programmed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. The indicator light in the instrument cluster will flash rapidly for 16 seconds. This shows that the system is arming. During this period, if a door is opened, the ignition switch is turned ON, or the power door locks are unlocked in any manner, the system will automatically disarm. After 16 seconds, the indicator light will flash slowly. This shows that the system is fully armed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Tamper Alert If the alarm was triggered, but the warning signals have timed out, the park and taillights flash three times (instead of the normal twice) when unlocking the vehicle with a valid Remote Keyless Entry (RKE) transmitter to alert the driver. Security System Manual Override The Vehicle Theft Security Alarm (VTSA) system will not arm if you lock the doors using the manual door lock plunger.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE REMOTE KEYLESS ENTRY This system allows you to lock or unlock the doors and trunk or activate the panic alarm from distances a maximum of 66 feet (20 meters) using a hand held radio transmitter. The transmitter need not be pointed at the vehicle to activate the system. Five Button Vehicle Key NOTE: The line of transmission must not be blocked with metal objects.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 1. Press and hold the LOCK button on a programmed key fob. 2. Continue to hold the LOCK button at least 4 seconds, but not longer than 10 seconds, then press and hold the UNLOCK button. A single chime will sound to indicate that this feature has changed. 3. Release both buttons at the same time. 4. Test the feature while outside of the vehicle, by pressing the LOCK/UNLOCK button on the keyfob.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Using The Express Down Window Feature — If Equipped The key fob remotely lowers both driver and passenger front windows simultaneously. Lowering the front windows using the key fob is a two step operation: 1. Press the unlock button once. 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Pressing the LOCK button on the key fob, while you are in the vehicle, will activate the Security Alarm. Opening a door with the Security Alarm activated will cause the alarm to sound. Press the UNLOCK button to deactivate the Security Alarm. To Program Transmitters: Refer to SENTRY KEY “Sentry Key Programming.” If you do not have a programmed transmitter, contact your dealer for details.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 Remote Start System — If Equipped Remote start conveniently starts the engine from outside the vehicle by using the Remote Keyless Entry (RKE) key fob while maintaining security. The system has a targeted range of 328 ft. (100 m). The vehicle must be locked, the deck lid and hood closed and the transmission in Park in order to start the engine using the Remote Start button on the key fob. NOTE: Remote start requires automatic transaxle equipped vehicles.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE cycle, the key must be cycled to the ignition RUN position and then repeat the start sequence. To shut off the vehicle when it is in Remote Start mode, press the remote start button once. In order to avoid inadvertent shut downs, the one-time press to shut down the vehicle will be disabled for two seconds after receipt of a valid remote start request.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Battery is at an acceptable charge level • Panic button on key fob is not depressed DOOR LOCKS Manual Door Locks Use the manual door lock plunger to lock the doors from inside the vehicle. If the plunger is down when the door is closed, the door will lock. Therefore, make sure the keys are not inside the vehicle before closing the door.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CAUTION! An unlocked vehicle is an invitation to thieves. Always remove the key from the ignition and lock all of the doors when leaving the vehicle unattended. Power Door Locks A door lock switch is located on the driver and passenger door panel. Press this switch to lock or unlock the doors. Automatic Door Locks—If Equipped The doors will lock automatically on vehicles with power door locks if all of the following conditions are met: 1.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Cycle the ignition switch between LOCK, and ON, and back to LOCK 4 times ending up in the LOCK position. 3. Depress the power door lock switch to lock the doors. 4. A single chime will indicate the completion of the programming. Auto Unlock The doors will unlock automatically on vehicles with power door locks if: 25 Features) in the Electronic Vehicle Information Center (EVIC) — if equipped section of this manual.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE or similar flat-bladed object into the lock and rotate approximately 1⁄4 turn to the lock or unlock position (as indicated by the stamped icons). NOTE: For emergency exit with the system engaged, move the lock plunger up (unlocked position), roll down the window, and open the door with the outside door handle. POWER WINDOWS Child Lock Control WARNING! Avoid trapping anyone in a vehicle in a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE window will go down automatically. To cancel the Auto Down movement, operate the switch either in the up or down direction and release the switch. 27 To open the window part way, press the window switch to the first detent and release it when you want the window to stop. The power window switches will remain active for up to 45 seconds after the ignition switch is turned off. Opening either front door will cancel this feature.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To close the window part way, lift the window switch to the first detent and release it when you want the window to stop. NOTE: • If the window runs into any obstacle during autoclosure, it will reverse direction and then stop. Remove the obstacle and use the window switch again to close the window. Window Lockout Switch The window lockout switch on the driver’s door allows you to disable the window control on the other doors.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Reset Express Up Any time the vehicle battery is disconnected, or goes dead, the auto-up function will be disabled. To reactivate the auto-up feature, pull the window switch up to close the window completely and continue to hold the switch up for an additional two seconds after the window is closed. 29 TRUNK RELEASE Use the Remote Keyless Entry Transmitter to open the trunk from outside the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE With the ignition ON, the word “deck” will display in place of the odometer display indicating that the trunk is open. The odometer display will reappear once the trunk is closed or if the trip button is depressed. Trunk Internal Emergency Release With the key in the lock position or with the key out, the word “deck” will display until the trunk is closed. On EVIC equipped vehicles, the words “Trunk Ajar” will display.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE OCCUPANT RESTRAINTS Some of the most important safety features in your vehicle are the restraint systems.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! In a collision, you and your passengers can suffer much greater injuries if you are not properly buckled up. You can strike the interior of your vehicle or other passengers, or you can be thrown out of the vehicle. Always be sure you and others in your vehicle are buckled up properly. Buckle up even though you are an excellent driver, even on short trips. Someone on the road may be a poor driver and cause a collision that includes you.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Be sure everyone in your vehicle is in a seat and using a seat belt properly. • Wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and can take the forces of a collision the best. • Wearing your belt in the wrong place could make your injuries in a collision much worse.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you as well. In a sudden stop, you could move too far forward, increasing the possibility of injury. Wear your seat belt snugly.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A belt that is worn under your arm is very dangerous. Your body could strike the inside surfaces of the vehicle in a collision, increasing head and neck injury. A belt worn under the arm can cause internal injuries. Ribs aren’t as strong as shoulder bones. Wear the belt over your shoulder so that your strongest bones will take the force in a collision. • A shoulder belt placed behind you will not protect you from injury during a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as possible and keep it snug. • A twisted belt can’t do its job as well. In a collision, it could even cut into you. Be sure the belt is straight. If you can’t straighten a belt in your vehicle, take it to your dealer and have it fixed. 5.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Adjustable Upper Shoulder Belt Anchorage In the front seat, the shoulder belt can be adjusted upward or downward to position the belt away from your neck. Push anchorage button to release the anchorage, and move it up or down to the position that serves you best. 37 you’ll prefer a higher position. When you release the anchorage, try to move it up or down to make sure that it is locked in position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode. In addition, the front passenger seat belt includes a two-stage load-limiting feature to enhance occupant protection for the same reason.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The Enhanced Warning System (BeltAlert) will be reactivated if the driver’s seat belt is unbuckled for more than 10 seconds and the vehicle speed is greater than 5 mph (8 km/h). Belt Alert Programming BeltAlert威 can be enabled or disabled by your authorized dealer or by following these steps: NOTE: The following steps must occur within the first 60 seconds of the ignition switch being turned to the ON or START position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seat Belt Extender If a seat belt is too short, even when fully extended and when the adjustable upper shoulder belt anchorage (if equipped) is in its lowest position, your dealer can provide you with a seat belt extender. This extender should be used only if the existing belt is not long enough. When it is not required, remove the extender, and stow it.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 NOTE: The front airbags are certified to the Federal regulations that allow less forceful deployment. • Supplemental Side Airbag Inflatable Curtains (SABIC) — If Equipped The front airbags have a multistage inflator design. This may allow the airbag to have different rates of inflation that are based on collision severity and occupant size.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Front Seat Airbag Features The front airbag system has dual-stage driver and front passenger airbags. This system provides output appropriate to the level of crash severity as determined by the Occupant Restraint Controller (ORC) and the impact sensors at the front of the car. The first stage inflator is triggered immediately during an impact that requires airbag deployment.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 Supplemental Side Airbag Inflatable Curtain (SABIC) Supplemental Side Airbag Inflatable Curtain (SABIC) Airbags offer side-impact protection to front and rear seat outboard occupants in addition to that provided by the body structure. Each airbag features inflated chambers place adjacent to the head of each outboard occupant that reduce the potential for side-impact head injuries. The curtains deploy downward, covering both windows on the impact side.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Airbag covers may not be obvious in the interior trim; but they will open to allow airbag deployment. The system includes sensors adjacent to both front and rear seat occupants that are calibrated to deploy during an impact severe enough to require airbag occupant protection. WARNING! • Do not put anything on or around the airbag covers or attempt to open them manually.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbags inflate in moderate to high speed impacts. Along with seat belts and pretensioners, front airbags work with the knee bolsters to provide improved protection for the driver and front passenger. Side airbags also work with seat belts to improve occupant protection. The seat belts are designed to protect you in many types of collisions. The front airbags deploy in moderate to severe frontal collisions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. All occupants should wear their lap and shoulder belts properly. 3. The driver and front passenger seats should be moved back as far as practical to allow the front airbags room to inflate. 4. If your vehicle has side airbags, do not lean against the door, airbags will inflate forcefully into the space between you and the door. 5. If the airbag system in this vehicle needs to be modified to accommodate a disabled person, contact the Customer Center.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag Deployment Sensors and Controls Occupant Restraint Controller (ORC) The Occupant Restraint Controller System (ORC) is part of a Federally regulated safety system required for this vehicle. The ORC determines if a frontal collision is severe enough to require the airbags to inflate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Ignoring the AIRBAG light in your instrument panel could mean you won’t have the airbags to protect you in a collision. If the light does not come on, stays on after you start the vehicle, or if it comes on as you drive, have the airbag system checked right away.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The following requirements must be strictly adhered to: • Do not make any modifications to the front passenger seat components, assembly, or to the seat cover in any way. • Do not use prior or future model year seat covers not designated for the specific model being repaired. Always use the correct seat cover specified for the vehicle. • Do not replace the seat cover with an aftermarket seat cover.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Turns on the interior lamps which remain on as long as the battery has power or until the ignition key is removed. • Unlocks the doors automatically If A Deployment Occurs The airbag systems are designed to deploy when the Occupant Restraint Controller (ORC) detect a moderateto-severe collision, to help restrain the driver and front passenger, and then immediately deflate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • It is not advisable to drive your vehicle after the airbags have deployed. If you are involved in another collision, the airbags will not be in place to protect you. WARNING! Deployed airbags and seat belt pretensioners cannot protect you in another collision. Have the airbags, seat belt pretensioners, and the front passenger seat belt retractor assembly, replaced by an authorized dealer as soon as possible.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Do not attempt to modify any part of your advanced airbag system. The airbag may inflate accidentally or may not function properly if modifications are made. Take your vehicle to an authorized dealer for any advanced airbag system service. If your seat including your trim cover and cushion needs to be serviced in any way (including removal or loosening/tightening of seat attachment bolts), take the vehicle to your authorized dealer.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: 1. A near-deployment event occurs when the airbag sensor detects severe vehicle deceleration usually indicative of a crash, but not severe enough to warrant airbag deployment. 2. Under certain circumstances, EDR data may not be recorded (e.g., loss of battery power).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Data Parameters that May Be Recorded: • Diagnostic trouble code(s) and warning lamp status for electronically-controlled safety systems, including the airbag system • Airbag disable lamp status (if equipped) • ⬙Time⬙ of airbag deployment (in terms of ignition cycles and vehicle mileage) • Airbag deployment level (if applicable) • Impact acceleration and angle • Seatbelt status • Brake status (service and parking brakes) • Accelerator status (including vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Infants And Small Children There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt. Always check the child seat owner’s manual to ensure you have the correct seat for your child. Use the restraint that is correct for your child. 55 • Rearward-facing child seats must NEVER be used in the front seat of a vehicle with a front passenger airbag.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint. • A rearward facing child restraint should only be used in a rear seat.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • If the seat belt has a switchable retractor, it will have a distinctive label. To operate the switchable retractor, please refer to Automatic-Locking Retractor (ALR) in this section. • In the rear seat, you may have trouble tightening the lap/shoulder belt on the child restraint because the buckle or latch plate is too close to the belt path opening on the restraint.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE the vehicle’s seat belt at the center position. If your child restraints are not LATCH-compatible, you can only install the child restraints using the vehicle’s seat belts. Please refer to “Installing the Child Restraint System” for typical installation instructions. Rear Seat LATCH Anchors Child restraints systems having attachments designed to connect to the lower anchorages are now available.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: When using the LATCH attaching system to install a child restraint, please ensure that all seat belts not being used for occupant restraints are stowed and out of reach of children. It is recommended that before installing the child restraint, buckle the seat belt so the seat belt is tucked behind the child restraint and out of reach.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE You will first loosen the adjusters on the lower straps and on the tether strap so that you can more easily attach the hooks or connectors to the vehicle anchorages. Next, attach the lower hooks or connectors over the top of the seat cover material.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 between the two posts. If not possible, lower the head restraint and pass the tether strap around the outboard side of the head restraint. 3. Attach the tether strap hook (A) of the child restraint to the anchor (B) and remove slack in the tether strap according to the child restraint manufacturer’s instructions. WARNING! 1 — Cover 3 — Attaching Strap A — Tether Strap and Hook B — Tether Anchor 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Pulling up on the shoulder portion of the lap/shoulder belt will tighten the belt. The cinching latch plate will keep the belt tight; however, any seat belt system will loosen with time, so check the belt occasionally, and pull it tight if necessary. Seat belts with an automatic locking retractor have a distinctive label on the seat belt webbing. The seat belt must be in the automatic locking mode in order to enable a child restraint to be tightly installed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Make sure that the child is upright in the seat. • The lap portion should be low on the hips and as snug as possible. • Check belt fit periodically. A child’s squirming or slouching can move the belt out of position. • If the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle. Never allow a child to put the shoulder belt under an arm or behind their back.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered as a normal part of the break-in and not interpreted as an indication of difficulty. SAFETY TIPS WARNING! If you are required to drive with the deck lid open, make sure that all windows are closed, and the climate control blower switch is set at high speed. DO NOT use the recirculation mode.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE turned ON. If the LED is not lit during starting, have it checked. If the light stays on or comes on while driving, have the system checked by an authorized dealer. Defroster Check operation by selecting the defrost mode and place the blower control on high speed. You should be able to feel the air directed against the windshield. NOTE: If the defrost feature is not functioning, the cause should be located and corrected immediately.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 䡵 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70 ▫ Inside Day/Night Mirror— If Equipped . . . . . .70 ▫ Automatic Dimming Mirror— If Equipped . . . .70 ▫ Electric Remote-Control Mirrors . . . . . . . . . . . .71 ▫ Adjusting Side View Mirrors . . . . . . . . . . . . . .72 ▫ Illuminated Vanity Mirrors — If Equipped . . . .73 䡵 Hands–Free Communication (UConnect™) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 䡵 Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104 ▫ Mist Feature . . . . . . . . . . . . . . . . . . . . . . . . . 110 ▫ Map/Reading/Interior Lights . . . . . . . . . . . . 104 ▫ Windshield Wiper Operation . . . . . . . . . . . . . 111 ▫ Multi-Function Control Lever . . . . . . . . . . . . . 105 ▫ Speed Sensitive Intermittent Wiper System . . . 111 ▫ Headlights, Parking Lights, Instrument Panel Lights . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 69 ▫ Programming A “Rolling Code” System . . . . . 117 ▫ Wind Buffeting . . . . . . . . . . . . . . . . . . . . . . . 123 ▫ Canadian Programming/Gate Programming . . 118 ▫ Sunroof Maintenance . . . . . . . . . . . . . . . . . . . 123 ▫ Using HomeLink . . . . . . . . . . . . . . . . . . . . . 118 ▫ Ignition Off Operation . . . . . . . . . . . . . . . . . . 123 ▫ Erasing HomeLink Buttons . . . . . . . . . . . . . . 118 䡵 Electrical Power Outlets . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Day/Night Mirror— If Equipped Adjust the mirror to center on the view through the rear window. A two-point pivot system allows for horizontal and vertical mirror adjustment. Automatic Dimming Mirror— If Equipped This mirror will automatically adjust for annoying headlight glare from vehicles behind you. Push in the button on the face of the mirror to activate the dimming feature.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 71 CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean. 3 Electric Remote-Control Mirrors Both of the outside mirrors can be adjusted by using the remote controls mounted on the driver’s door panel. A rotary knob selects the left mirror, right mirror, or off position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Outside Mirror — Passenger’s Side Adjust the convex outside mirror so you can just see the side of your vehicle in the part of the mirror closest to the vehicle. WARNING! Mirror Directions Adjusting Side View Mirrors Outside Mirror — Driver’s Side Adjust the outside mirror to center on the adjacent lane of traffic, with a slight overlap of the view obtained on the inside mirror.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Illuminated Vanity Mirrors — If Equipped An illuminated vanity mirror is on each sun visor. To use the mirror, rotate the sun visor down and swing the mirror cover upward. The lights will turn on automatically. Closing the mirror cover turns off the lights. 73 HANDS–FREE COMMUNICATION (UConnect™) — IF EQUIPPED UConnect™ is a voice-activated, hands-free, in- vehicle communications system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE The UConnect™ phone book enables you to store up to 32 names and four numbers per name. Each language has a separate 32-name phone book accessible only in that language. This system is driven through your Bluetooth™ Hands-Free profile cellular phone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 75 system can be adjusted either from the radio volume control knob or from the steering wheel radio control (right switch), if so equipped. The radio display will be used for visual prompts from the UConnect™ system such as ⬙CELL⬙ or caller ID on certain radios. UConnect Buttons The UConnect™ system can be used with any HandsFree Profile certified Bluetooth™ cellular phone. See www.chrysler.com/uconnect for supported phones.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • For each feature explanation in this section, only the combined form of the voice command is given. You can also break the commands into parts and say each part of the command, when you are asked for it. For example, you can use the combined form voice command ⬙Phonebook New Entry,⬙ or you can break the combined form command into two voice commands: ⬙Phonebook⬙ and ⬙New Entry.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After the ⬙Ready⬙ prompt and the following beep, say ⬙Setup Phone Pairing.⬙ • When prompted, after the beep, say ⬙Pair a Phone⬙ and follow the audible prompts. • You will be asked to say a four-digit pin number, which you will later need to enter into your cellular. You can enter any four-digit pin number. You will not need to remember this pin number after the initial pairing process.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The UConnect™ system will confirm the phone number and then dial. The number will appear in the display of certain radios. Call by Saying a Name • Press the “Phone” button to begin. • After the ⬙Ready⬙ prompt and the following beep, say “Call.⬙ • System will prompt you to say the name of the person you want call. • After the ⬙Ready⬙ prompt and the following beep, say the name of the person you want to call.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE The UConnect™ system will allow you to enter up to 32 names in the phone book with each name having up to four associated phone numbers and designations. Each language has a separate 32-name phone book accessible only in that language. Edit Entries in the UConnect™ Phonebook NOTE: Editing names in the phone book is recommended when vehicle is not in motion. • Press the ’Phone’ button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Phonebook Edit.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE from which you choose. To select one of the entries from the list, press the ⬙Voice Recognition⬙ button while the UConnect™ system is playing the desired entry and say ⬙Delete.⬙ • After you enter the name, the UConnect™ system will ask you which designation you wish to delete, home, work, mobile, pager, or all. Say the designation you wish to delete. • Note that only the phone book entry in the current language is deleted.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Phone Call Features The following features can be accessed through the UConnect™ system if the feature(s) are available on your cellular service plan. For example, if your cellular service plan provides three-way calling, this feature can be accessed through the UConnect™ system. Check with your cellular service provider for the features that you have.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Toggling Between Calls If two calls are in progress (one active and one on hold), press the ’Phone’ button until you hear a single beep indicating that the active and hold status of the two calls have switched. Only one call can be placed on hold at one time. there is a call on hold, it will become the new active call. If the active call is terminated by the far end, a call on hold may not become active automatically. This is cell phone dependent.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE until the vehicle battery condition dictates cessation of the call on the UConnect™ system and transfer of the call to the mobile phone. • After ignition key is switched to off, a call can continue on the UConnect™ system for certain duration, after which the call is automatically transferred from the UConnect™ system to the mobile phone. • An active call is automatically transferred to the mobile phone after ignition key is switched to off.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The emergency number dialed is based on the Country where the vehicle is purchased (911 for USA and Canada and 060 for Mexico). The number dialed may not be applicable with the available cellular service and area. The UConnect™ system does slightly lower your chances of successfully making a phone call as to that for the cell phone directly.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE You can use your UConnect™ system to access a voicemail system or an automated service, such as, paging service or automated customer service. Some services require immediate response selection, in some instances, that may be too quick for use of UConnect™ system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Dialing Using the Cellular Phone Keypad You can dial a phone number with your cellular phone keypad and still use the UConnect™ system (while dialing via the cell phone keypad, the user must exercise caution and take precautionary safety measures). By dialing a number with your paired Bluetooth™ cellular phone, the audio will be played through your vehicle’s audio system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Connect or Disconnect Link Between the UConnect™ System and Cellular Phone Your cellular phone can be paired with many different electronic devices, but can only be actively ⬙connected⬙ with one electronic device at a time. If you would like to connect or disconnect the Bluetooth™ connection between a UConnect™ paired cellular phone and the UConnect™ system, then follow the instruction described in your cellular phone user’s manual.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Delete UConnect™ Paired Cellular Phones • Press the ’Phone’ button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Setup Phone Pairing.⬙ • At the next prompt, say ⬙Delete⬙ and follow the prompts. • You can also press the ⬘Voice Recognition’ button anytime while the list is being played, and then choose the phone you wish to delete.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 • Make sure that no one other than you is speaking during a voice recognition period. • Storing names in phone book when vehicle is not in motion is recommended. • Performance is maximized under: • It is not recommended to store similar sounding names in the UConnect™ phone book. • low-to-medium blower setting, • low-to-medium vehicle speed, • low road noise, • smooth road surface, • fully closed windows, • dry weather condition.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • low-to-medium vehicle speed, • low road noise, • smooth road surface, • fully closed windows, and • dry weather condition. • operation from driver seat. • Performance, such as audio clarity, echo, and loudness to a large degree rely on the phone and network, and not the UConnect™ system. • Echo at far end can sometime be reduced by lowering the in-vehicle audio volume.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91 3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Commands Primary Alternate(s) zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location all call cancel confirmation prompts continue delete dial edit emergency English erase all Espanol Fancais help home language list names list phones mobile mute mute off new entry no pager
UNDERSTANDING THE FEATURES OF YOUR VEHICLE pair a phone phone pairing phonebook previous record again redial return to main menu select phone send set up towing assistance transfer call try again voice training work yes pairing phone book 95 General Information This device complies with part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE SEATS Manual Front Seat Adjustments Forward/Rearward The adjusting bar is at the front of the seats, near the floor. Pull the bar up to move the seat to the desired position. Driver Seat Manual Height Adjuster — If Equipped A lever style height adjustment feature enhances comfort for petite as well as tall drivers. A lever with a ratcheting mechanism, located on the outboard side of the seat, raises and lowers it. Total travel is 2.2 in. (56 mm).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Reclining Bucket Seats The recliner control is on the side of the seat. To recline, lean forward slightly before lifting the lever, then lean back to the desired position and release the lever. Lean forward and lift the lever to return the seatback to its normal position. Seat Back Fold Forward 97 WARNING! • Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Lumbar Support — If Equipped This feature allows you to increase or decrease the amount of lumbar support. The control lever is located on the outboard side of the driver’s seatback. Turn the control lever downward to increase and upward to decrease the desired amount of lumbar support. Power Seats — If Equipped The power seat switches are on the outboard side of the seat near the floor.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Do not place any article under a power seat as it may cause damage to the seat controls. Heated Seats — If Equipped This feature heats leather or cloth front driver and passenger seats. The controls for the heated seats are located in the center console above the climate controls. There are indicator lights in the switches, which indicate a low heat setting (one lamp lit) or high heat setting (2 lamps lit).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Fold Flat Front Passenger Seat The recline handle on the front passenger seat also releases the seatback to fold forward. The hard seatback features a work surface and a molded rim for retaining items stored on the seat back panel.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Adjustable Head Restraints Head restraints can reduce the risk of whiplash injury in the event of impact from the rear. Adjust the restraints so that the upper edge is as high as practical. To raise, pull up on the head restraint. To lower, depress the button on the post guide and push down on the head restraint. Adjustable Head Restraint 101 Folding Rear Seat To provide additional storage area, the rear seatback can be folded forward.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! The rear cargo area of the vehicle (with the rear seatbacks in the locked-up or folded down position) should not be used as a play area by children. They could be seriously injured in an accident. Children should be seated and using the proper restraint system. Folding Rear Seat Center Armrest The rear seat is equipped with a folding armrest with cup holders.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE TO OPEN AND CLOSE THE HOOD To open the hood, two latches must be released. First pull the hood release lever located under the left side of the instrument panel. 103 Then lift the secondary latch located under the front edge of the hood, near the center and raise the hood.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Use the hood prop rod to secure the hood in the open position. Place the upper end of the prop rod in the hole on the left underside of the hood. WARNING! If the hood is not fully latched it could fly up when the vehicle is moving and block your forward vision. You could have a collision. Be sure all hood latches are fully latched before driving.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To protect the battery, the interior lights will turn off automatically 10 minutes after the ignition switch is moved to the LOCK position. This will occur if the interior lights were switched on manually or are on because a door is open. This includes the glove box light, but not the trunk light. To restore interior light operation, either turn the ignition switch ON or cycle the light switch.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To change the brightness of the instrument panel lights, rotate the center portion of the Multi-Function Control Lever up or down. Headlight Time Delay There is also a feature that delays turning off the vehicle lights for 30, 60, or 90 seconds after the ignition switch is turned OFF. To activate the headlight delay, the multifunction control lever must be rotated to the “Off” position after the ignition switch is turned OFF.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 Daytime Running Lights (DRL) — If Equipped The high beam lights will come on as Daytime Running Lights (DRL) at DRL intensity (lower), whenever the ignition is on, the engine is running, the headlight switch is off, the parking brake is off, the turn signal is off, and the gearshift lever is in any position except park.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Turn Signals Move the Multi-Function Control Lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights. You can signal a lane change by moving the lever partially up or down without moving beyond the detent. bulb. If an indicator fails to light when the lever is moved, it would suggest that the fuse or indicator bulb is defective.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WINDSHIELD WIPERS AND WASHERS The wipers and washers are operated by a switch on the control lever. The lever is located on the right side of the steering column. 109 Windshield Washers To use the washer, pull the multi-function control lever toward you and hold while spray is desired.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Mist Feature Push down on the wiper control lever to activate a single wipe to clear the windshield of road mist or spray from a passing vehicle. As long as the lever is held down, the wipers will continue to operate. Mist Control WARNING! Sudden loss of visibility through the windshield could lead to an accident. You might not see other vehicles or other obstacles.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Windshield Wiper Operation Turn to the second detent for low wiper speed and the third detent for high wiper speed. 111 delay time. The delay can be regulated from a maximum of approximately 18 seconds between cycles, to a cycle every second. NOTE: The wiper delay times depend on vehicle speed. If the vehicle is moving less than 10 mph (16 km/h), delay times will be doubled.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE TILT/TELESCOPING STEERING COLUMN This feature allows you to tilt the steering column upward or downward. It also allows you to lengthen or shorten the steering column. The tilt/telescoping control handle is located below the steering wheel at the end of the steering column. outward or push it inward as desired. To lock the steering column in position, push the control handle inward until fully engaged.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ELECTRONIC SPEED CONTROL — IF EQUIPPED When engaged, this device takes over the accelerator operation at speeds greater than 25 mph (40 km/h). The speed control lever is located on the right side of the steering wheel. 113 OFF, push the ON/OFF button a second time. The CRUISE indicator will turn off. The system should be turned OFF when not in use.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The vehicle should be traveling at a steady speed and on level ground before pressing the SET lever. To Deactivate: A soft tap on the brake pedal, pulling the speed control lever towards you “CANCEL”, or normal brake pressure while slowing the vehicle will deactivate speed control without erasing the set speed memory. Pressing the ON/OFF button or turning off the ignition switch erases the set speed memory.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Accelerate For Passing: Depress the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. 115 For additional information on HomeLink威, call 1–800– 355–3515, or on the internet at www.homelink.com. Using Speed Control On Hills 3 NOTE: The speed control system maintains speed up and down hills. A slight speed change on moderate hills is normal.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE in the hand-held transmitter of the device being programmed. This will allow for quicker training and accurate transmission of the radio-frequency signal. If your garage door opener (located in the garage) is equipped with an antenna, make sure that the antenna is hanging straight down. 1. Erase the factory test codes by pressing the two outside buttons. Release the buttons when the light in the Universal Transceiver begins to flash (about 20 seconds).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. The indicator light in the Universal Transceiver will begin to flash, first slowly and then rapidly. The rapid flashing indicates successful programming. If after 90 seconds the indicator light does not flash rapidly or goes out, return to step 1 and repeat the procedure. To train the other buttons, repeat steps 3 and 4. Be sure to keep your hand held transmitters in case you need to retrain the Universal Transceiver.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE training process. Some garage door openers may require you to do this procedure a third time to complete the training. NOTE: When programming such a garage door opener or gate, unplug the device to prevent possible damage to the garage door or gate motor.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Reprogramming a Single HomeLink Button To program a device with a previously trained HomeLink button, follow these steps: 1. Press and hold the Universal Transceiver button to be reprogrammed. Do not release until step 4 has been completed. 2. When the indicator light begins to flash slowly (after 20 seconds), position the hand held transmitter one to three inches away from the button to be trained. 3. Press and hold the hand held transmitter button. 4.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • A moving garage door can cause injury to people and pets in the path of the door. People or pets could be seriously or fatally injured. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by federal safety standards. This includes most garage door opener models manufactured after 1982. Do not use a garage door opener without these safety features, it could cause injury or death.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE POWER SUNROOF — IF EQUIPPED The sunroof controls are mounted between the sun visors in the Dome / Reading Lamp. Power Sunroof Switch 121 WARNING! • Never leave children in a vehicle, with the keys in the ignition switch. Occupants, particularly unattended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Opening Sunroof - Manual Press the switch rearward and hold, and the sunroof will open automatically from any position. The sunroof will open fully, then stop automatically. During this operation, any release of the sunroof switch will stop the sunroof. Closing Sunroof - Express Press the switch forward and release, and the sunroof will close automatically from any position. The sunroof will close fully, then stop automatically. This is called Express Close.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Sunshade Operation The sunshade can be opened manually. However, the sunshade will open automatically as the sunroof opens. NOTE: The sunshade cannot be closed if the sunroof is open. Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if so equipped) in certain open or partially open positions.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ELECTRICAL POWER OUTLETS There are two 12-volt electrical outlets on this vehicle. Both of the outlets are protected by a fuse. The 12-volt power outlet next to the ash receiver tray (if equipped with an optional Smoker’s Package) has power available only when the ignition is on. This outlet will also operate a conventional cigar lighter unit.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 NOTE: Due to built-in overload protection, the inverter will shut down if the power rating is exceeded. WARNING! Console Interior ELECTRICAL POWER INVERTER — IF EQUIPPED There is a 115 VAC (150-Watts Maximum) outlet in the center console for added convenience. This outlet can power cell phones, electronics, and other low power devices. To Avoid Serious Injury or Death: • Do not use a 3-Prong Adaptor. • Do not insert any objects into the receptacles.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Electrical Outlet Use With Engine Off CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e. cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting. • Accessories that draw higher power (i.e. coolers, vacuum cleaners, lights, etc.) will degrade the battery even more quickly.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 CAUTION! If your vehicle is equipped with the heated and cooled cup holder, locate the cup holder ash receiver in the forward cup holder. The optional ash receiver also comes with a cigar lighter. You may use the power outlet, located in the instrument panel below the climate control knob, or in the bottom of the console compartment, for this cigar lighter.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONSOLE FEATURES Console Features The center console armrest slides forward from design position to provide added user comfort. Two cup holders, each of which can accommodate large sized fast food beverage containers. A one piece cup holder insert for both cavities can easily be removed for cleaning. The cup holders will also accommodate large size cups and 20 oz. bottles. (An optional removable ashtray may be located in the one cup holder.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 • The lower bin can be accessed directly, without first exposing the upper bin, by operating the right latch with the armrest down. Video Console — If Equipped The optional VES™(Video Entertainment System) includes the following components: • The first storage bin can be used to hold smaller items. • The screen for a rear seat DVD player is stored under the armrest.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CUP HOLDERS Heated or Cooled Cup Holder — If Equipped With this feature the rear cavity of the cup holder can heat or cool the beverage container it is holding. The rear cup holder can heat from room temperature (70°F /21°C), to 140°F (60°C) or cool it to near freezing, 0°F (–20°C). The switch is located on the front of the center console and has three positions: HEAT, OFF, COOL. When the unit is on and the LED is Red, the cup holder is being heated.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Bottle Holders There are built-in bottle holders located in both rear door trim panels. Rear Bottle Holder 131 WARNING! If containers of hot liquid are placed in the bottle holder, they can spill when the door is closed, burning the occupants. Be careful when closing the doors to avoid injury.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 Instrument Panel Features . . . . . . . . . . . . . . . 136 ▫ Telephone — If Equipped . . . . . . . . . . . . . . . 153 䡵 Instrument Cluster—Base . . . . . . . . . . . . . . . . 137 ▫ Navigation — If Equipped . . . . . . . . . . . . . . . 154 䡵 Instrument Cluster—Premium . . . . . . . . . . . . 138 ▫ Personal Settings (Customer Programmable Features) . . . . . . . . 155 䡵 Instrument Cluster Descriptions . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL ▫ FM Reception . . . . . . . . . . . . . . . . . . . . . . . . 159 ▫ Notes On Playing MP3 Files . . . . . . . . . . . . . 178 䡵 Sales Code REQ — AM/FM Stereo Radio And 6–Disc CD/DVD Changer (MP3/WMA Aux Jack) . . . . . . . . . . . . . . . . . . 159 ▫ List Button (CD Mode For MP3 Play) . . . . . . . 180 ▫ Operating Instructions - Radio Mode . . . . . . . 160 ▫ Operation Instructions (Disc Mode For CD And MP3/WMA Audio Play, DVD-Video) . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Operating Instructions Hands Free Phone (If Equipped) . . . . . . . . . . 186 ▫ Operating Instructions - Video Entertainment System (VES®)威 (If Equipped) . . . . . . . . . . . . 186 䡵 Video Entertainment System — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 187 䡵 Radio Operation And Cellular Phones . . . . . . . 188 䡵 Remote Sound System Controls — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 188 ▫ Radio Operation . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT PANEL FEATURES Instrument Panel
UNDERSTANDING YOUR INSTRUMENT PANEL 137 INSTRUMENT CLUSTER—BASE 4
UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER—PREMIUM 120 MPH Cluster with EVIC
UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTIONS 1. Fuel Gauge When the ignition switch is in the ON position, the pointer will show the level of fuel remaining in the fuel tank. 2. Fuel Door Reminder This is a reminder that the Fuel Filler Door is located on the left side of the vehicle. 3. Temperature Gauge The temperature gauge shows engine coolant temperature. Any reading below the red area of the gauge shows that the engine cooling system is operating properly.
UNDERSTANDING YOUR INSTRUMENT PANEL 6. Low Fuel Light When the fuel level drops to 2 gallons, the fuel symbol will light and a single chime will sound. 7. Charging System Light This light shows the status of the electrical charging system. The light should come on briefly when the ignition is first turned on and remain on briefly as a bulb check. If the light stays on or comes on while driving, turn off some of the vehicle’s electrical devices, such as the Fog Lights or Rear Defroster.
UNDERSTANDING YOUR INSTRUMENT PANEL The light does not show the quantity of oil in the engine. This can be determined using the procedure shown in Section 7. 12. Engine Temperature Warning Light This light warns of an overheated engine condition. If the engine is critically hot, a warning chime will sound 10 times. After the chime turns off, the engine will still be critically hot until the light goes out. 13. Transmission Range Indicator This display indicator shows the automatic transaxle gear selection.
UNDERSTANDING YOUR INSTRUMENT PANEL off for 60 seconds when a system fault is detected. The flash cycle will repeat every ten minutes or until the fault condition is removed and reset. If this indicator comes on, the entire, PRNDL/ odometer, display will brighten to FULL DAYTIME INTENSITY and will not be dimmable. CAUTION! The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and warning have been established for the tire size equipped on your vehicle.
UNDERSTANDING YOUR INSTRUMENT PANEL 143 trip odometer, display the desired trip odometer to be reset then push and hold the button until the display resets (approximately 2 seconds). stays on through several of your typical driving cycles. In most situations the vehicle will drive normally and will not require towing. U.S. federal regulations require that upon transfer of vehicle ownership, the seller certify to the purchaser the correct mileage that the vehicle has been driven.
UNDERSTANDING YOUR INSTRUMENT PANEL 19. Electronic Throttle Control Indicator Light This red illuminated light informs you of a problem with the Electronic Throttle Control system. If a problem is detected, the light will come on while the engine is running. If the light remains lit with the engine running your vehicle will usually be drivable and not need towing, however see your dealer for service as soon as possible. 20.
UNDERSTANDING YOUR INSTRUMENT PANEL BAS Warning Lamp” comes on continuously with the engine running, a malfunction has been detected in either the ESP or the BAS system. If this light remains on after several ignition cycles, and the vehicle has been driven several miles at speeds greater than 30 mph (48 km/h), see your authorized dealer as soon as possible. 24. Anti-Lock Warning Light (ABS) — If Equipped This light monitors the Anti-Lock Brake System (ABS) described elsewhere in this manual.
UNDERSTANDING YOUR INSTRUMENT PANEL indicated by the Brake Warning Light which will turn on when the brake fluid level in the master cylinder has dropped below a specified level. In the event of an EBD failure, the Brake Warning Light will turn on along with the ABS Light. Immediate repair to the ABS system is required. The light will remain on until the cause is corrected.
UNDERSTANDING YOUR INSTRUMENT PANEL ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) – IF EQUIPPED 147 • Compass heading (N, S, E, W, NE, NW, SE, SW) • Outside temperature display (°F or °C) • Trip computer functions • UConnect™ hands-free communication system displays (if equipped) • Audio mode display – 12 preset Radio Stations or CD Title and Track number when playing • Tire Pressure Monitor System (TPMS) (if equipped) • Navigation system screens (if equipped) EVIC Display Location The Electronic Vehicl
UNDERSTANDING YOUR INSTRUMENT PANEL • Right Front Turn Signal Light Out (with a single chime) • Left/Right Front Door Ajar (one or more, with a single chime if speed is above 1 mph) • Right Rear Turn Signal Light Out (with a single chime) • Left/Right Rear Door Ajar (one or more, with a single chime if speed is above 1 mph) • RKE (Remote Keyless Entry) Battery Low (with a single chime) • Memory #1/#2 Profile Set • Memory #1/#2 Profile Recall • Memory System Disabled – Vehicle Not In Park (with a s
UNDERSTANDING YOUR INSTRUMENT PANEL 149 • Distance To Empty • Elapsed Time • Display Units of Measure in Press the STEP button to cycle through all the Trip Computer functions. The Trip Functions mode displays the following information: Trip Functions MENU / STEP Button Press and release the MENU / STEP button (located near the radio) until one of the following Trip Functions displays in the EVIC: • Average Fuel Economy • Average Fuel Economy Shows the average fuel economy since the last reset.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Significant changes in driving style or vehicle loading will greatly affect the actual drivable distance of the vehicle, regardless of the DTE displayed value. • When the DTE value is less than 30 miles (48 km) estimated driving distance, the DTE display will change to a text display of ⬙LOW FUEL.⬙ This display will continue until the vehicle runs out of fuel.
UNDERSTANDING YOUR INSTRUMENT PANEL is calibrated. Calibrate the compass by completing one or more 360° turns (in an area free from large metal or metallic objects) until the “FLASH THE CAL” message displayed in the EVIC turns off. The compass will now function normally. Manual Compass Calibration If the compass appears erratic, inaccurate, or abnormal, you may wish to calibrate the compass manually. Prior to calibrating the compass, make sure the proper zone is selected.
UNDERSTANDING YOUR INSTRUMENT PANEL Procedure to Update the Variance: 1. Turn the ignition switch to the ON position while leaving the transmission selector in PARK. 2. Press the Step Button Several Times until “Personal Settings” is displayed in the EVIC window. 3. Once in “Personal Settings,” Press the STEP button until “Compass Variance” and the current value displays in the EVIC window. 4.
UNDERSTANDING YOUR INSTRUMENT PANEL Telephone — If Equipped Press and release the MENU button until “Telephone” displays in the EVIC. When the appropriate conditions exist, the EVIC provides the following telephone information: • Phone status: idle; voice mail; roaming; battery strength; and signal strength in increments of 20 percent. • Call status: Incoming call; connecting; connected; air time in minutes and seconds; call ended; call failed; roaming; and no phone connection.
UNDERSTANDING YOUR INSTRUMENT PANEL The EVIC displays this symbol to indicate that you have voice mail. Voice Mail The EVIC displays this symbol to indicate a text message. The EVIC displays this symbol to indicate that the UConnect™ phone is currently not available. Phone Not Available Navigation — If Equipped Text Message The EVIC displays this symbol to indicate the battery strength of the UConnect™ phone.
UNDERSTANDING YOUR INSTRUMENT PANEL Turn-By-Turn Directions The EVIC displays turn-by-turn directions to a programmed destination when Turn-By-Turn Navigation is enabled through Personal Settings. When enabled, the EVIC displays the name of the approaching road at the top of the screen, followed by an arrow to indicate the direction to turn the vehicle, and a count down to indicate the distance to the turn. NOTE: Refer to your “Navigation User’s Manual” for detailed operating instructions.
UNDERSTANDING YOUR INSTRUMENT PANEL Remote Key Unlock Driver Door 1st When Driver Door 1st Press is selected, only the driver’s door will unlock on the first press of the remote keyless entry unlock button. When Driver Door 1st Press is selected, you must press of the remote keyless entry unlock button twice to unlock the passenger’s doors. When All Doors 1st Press is selected, all of the doors will unlock on the first press of the remote keyless entry unlock button.
UNDERSTANDING YOUR INSTRUMENT PANEL Key-Off Power Display When this feature is selected, the power window switches, radio, hands–free system (if equipped), power sunroof (if equipped), and power outlets will remain active for up to 10 minutes after the ignition switch is turned off. Opening a vehicle door will cancel this feature. To make your selection, press and hold the RESET button until “Off,” “45 sec.,” “5 min.,” or “10 min.” appears.
UNDERSTANDING YOUR INSTRUMENT PANEL ELECTRONIC DIGITAL CLOCK The clock and radio each use the display panel built into the radio. A digital readout shows the frequency and/or time in hours and minutes (depending on your radio model) whenever the ignition switch is in the “ON” or “ACC” position. When the ignition switch is in the “OFF” position, or when the radio frequency is being displayed, time keeping is accurately maintained.
UNDERSTANDING YOUR INSTRUMENT PANEL Electrical Disturbances Radio waves may pick up electrical disturbances during transmission. They mainly affect the wave amplitude, and thus remain a part of the AM reception. They interfere very little with the frequency variations that carry the FM signal. SALES CODE REQ — AM/FM STEREO RADIO AND 6–DISC CD/DVD CHANGER (MP3/WMA AUX JACK) NOTE: The radio sales code is located on the lower right side of your radio faceplate.
UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Control (Rotary) Press the ON/VOL control to turn the radio ON. Press the ON/VOL a second time to turn OFF the radio. Electronic Volume Control The electronic volume control turns continuously (360 degrees) in either direction without stopping.
UNDERSTANDING YOUR INSTRUMENT PANEL 3. After the hours are adjusted, press the right side TUNE control knob to set the minutes. The minutes will begin to blink. 4. Adjust the minutes using the right side TUNE control knob. Press the TUNE control knob to save time change. 5. To exit, press any button/knob or wait 5 seconds. The clock can also be set by pressing the SETUP button and selecting the “SET HOME CLOCK” entry. Once in this display follow the above procedure, starting at step 2.
UNDERSTANDING YOUR INSTRUMENT PANEL MUSIC TYPE Button (Radio Mode) Pressing this button once will turn on the Music Type mode for 5 seconds. Pressing the Music Type button or turning the TUNE control knob within 5 seconds will allow the program format type to be selected. Many radio stations do not currently broadcast Music Type information.
UNDERSTANDING YOUR INSTRUMENT PANEL 163 If a preset button is activated while in the Music Type (Program Type) mode, the Music Type mode will be exited and the radio will tune to the preset station. • Subtitle – Repeatedly Pressing SELECT will switch subtitles to different subtitle languages that are available on the disc (If Equipped).
UNDERSTANDING YOUR INSTRUMENT PANEL • Set Home Clock - Pressing the SELECT button will allow user to set the clock. Turn TUNE control knob to adjust the hours then press and turn the TUNE control knob to adjust the minutes. Press the TUNE control knob again to save changes. • Player Defaults - Selecting this item will allow the user to scroll through the following items, and set defaults according to customer preference.
UNDERSTANDING YOUR INSTRUMENT PANEL Aspect Ratio — If Equipped Selecting this item will allow the user to choose between wide screen, pan scan, and letter box. AutoPlay — If Equipped When this is set to ON and a DVD video is inserted, it will bypass the DVD menu screen and automatically play the movie. In some rare cases, the DVD player may not auto play the main title. In such cases, use the menu button on the remote control to select desired title to play.
UNDERSTANDING YOUR INSTRUMENT PANEL DISC Button Pressing the DISC button will allow you to switch from AM/FM modes to Disc modes. Operation Instructions - (DISC MODE for CD and MP3/WMA Audio Play, DVD-VIDEO) The radio DVD player and many DVD discs are coded by geographic region. These region codes must match in order for the disc to play. If the region code for the DVD disc does not match the region code for the radio DVD player, it will not play the disc.
UNDERSTANDING YOUR INSTRUMENT PANEL Eject Button — Ejecting Compact Disc(s) Press the eject button and the push-button with the corresponding number (1-6) where the CD was loaded and the disc will unload and move to the entrance for easy removal. Radio display will show ⬙EJECTING DISC⬙ when the disc is being ejected and prompt the user to remove the disc. Press and hold the eject button for 5 seconds and all CDs will be ejected from the radio. The disc can be ejected with the radio and ignition OFF.
UNDERSTANDING YOUR INSTRUMENT PANEL Notes On Playing MP3/WMA Files The radio can play MP3/WMA files, however, acceptable MP3/WMA file recording media and formats are limited. When writing MP3/WMA files, pay attention to the following restrictions. Supported Media (Disc Types) The MP3/WMA file recording media supported by the radio are CDDA, CD-R, CD-RW, MP3,WMA, DVD Video, DVD-R, DVD-RW, DVD+R, DVD+RW, and CDDA+MP3.
UNDERSTANDING YOUR INSTRUMENT PANEL When using the MP3/WMA encoder to compress audio data to an MP3/WMA file, the bit rate and sampling frequencies in the following table are supported. In addition, variable bit rates (VBR) are also supported. The majority of MP3/WMA files use a 44.1 kHz sampling rate and a 192, 160, 128, 96 or VBR bit rates.
UNDERSTANDING YOUR INSTRUMENT PANEL LIST Button (DISC Mode for MP3/WMA Play) Pressing the LIST button will bring up a list of all folders on the disc. Scrolling up or down the list is done by turning the TUNE control knob. Selecting a folder by pressing the TUNE control knob will begin playing the files contained in that folder (or the next folder in sequence if the selection does not contain playable files).
UNDERSTANDING YOUR INSTRUMENT PANEL PSCAN Button (Auxiliary Mode) No function. TIME Button (Auxiliary Mode) Press this button to change the display from elapsed playing time to time of day. The time of day will be displayed for 5 seconds. RW/FF (Auxiliary Mode) No function. SET Button (Auxiliary Mode) No function. Operating Instructions - Hands Free Phone (If Equipped) Refer to Hands Free Phone in Section 3 of the Owner’s Manual.
UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE RES — AM/FM STEREO RADIO WITH CD PLAYER (MP3 AUX JACK) NOTE: The radio sales code is located on the lower right side of your radio faceplate. Power Switch/Volume Control (Rotary) Press the ON/VOLUME control knob to turn the radio on. Press the ON/VOLUME control knob a second time to turn the radio off. Electronic Volume Control The electronic volume control turns continuously (360 degrees) in either direction without stopping.
UNDERSTANDING YOUR INSTRUMENT PANEL SCAN Button Pressing the SCAN button causes the tuner to search for the next listenable station, in either AM or FM frequencies, pausing for 5 seconds at each listenable station before continuing to the next. To stop the search, press SCAN a second time. INFO Button Press the INFO button for an RDS station (one with call letters displayed). The radio will return a Radio Text message broadcast from an FM station (FM mode only).
UNDERSTANDING YOUR INSTRUMENT PANEL Setting the Tone, Balance, and Fade Press the rotary TUNE control knob and BASS will display. Turn the TUNE control knob to the right or left to increase or decrease the Bass tones. Press the rotary TUNE control knob a second time and MID will display. Turn the TUNE control knob to the right or left to increase or decrease the Mid Range tones. Press the rotary TUNE control knob a third time and TREBLE will display.
UNDERSTANDING YOUR INSTRUMENT PANEL News Nostalgia Oldies Personality Public Rhythm and Blues Religious Music Religious Talk Rock Soft Soft Rock Soft Rhythm and Blues Sports Talk Top 40 Weather News Nostalga Oldies Persnlty Public R&B Rel Musc Rel Talk Rock Soft Soft Rck Soft R&B Sports Talk Top 40 Weather By pressing the SEEK button when the Music Type icon is displayed, the radio will be tuned to the next frequency station with the same selected Music Type name.
UNDERSTANDING YOUR INSTRUMENT PANEL You may add a second station to each push-button by repeating the above procedure with this exception: Press the SET button twice and SET 2 will show in the display window. Each button can be set for SET 1 and SET 2 in both AM and FM. This allows a total of 12 AM and 12 FM stations to be stored into push-button memory. The stations stored in SET 2 memory can be selected by pressing the push-button twice.
UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! • This CD player will accept 4 3/4 inch (12 cm) discs only. The use of other sized discs may damage the CD player mechanism. • Do not use adhesive labels. These labels can peel away and jam the player mechanism. • RES is a single CD player. Do not attempt to insert a second CD if one is already loaded. • Dual—media disc types (one side is a DVD, the other side is a CD) should not be used, and can cause damage to the player.
UNDERSTANDING YOUR INSTRUMENT PANEL Press and hold FF (Fast Forward) and the CD player will begin to fast forward until FF is released or RW or another CD button is pressed. The RW (Reverse) button works in a similar manner. AM or FM Button Switches the Radio to the Radio mode. RND Button (Random Play Button) Press this button while the CD is playing to activate Random Play. This feature plays the selections on the compact disc in random order to provide an interesting change of pace.
UNDERSTANDING YOUR INSTRUMENT PANEL • Maximum number of characters in file/folder names: • Level 1: 12 (including a separator ⬙.⬙ and a 3-character extension) • Level 2: 31 (including a separator ⬙.⬙ and a 3-character extension) Multisession disc formats are supported by the radio. Multisession discs may contain combinations of normal CD audio tracks and computer files (including MP3 files). Discs created with an option such as ⬙keep disc open after writing⬙ are most likely multisession discs.
UNDERSTANDING YOUR INSTRUMENT PANEL Playback of MP3 Files When a medium containing MP3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3 files.
UNDERSTANDING YOUR INSTRUMENT PANEL Operation Instructions - Auxiliary Mode The auxiliary (AUX) jack is an audio input jack, which allows the user to plug in a portable device such as an MP3 player, or cassette player, and utilize the vehicle’s audio system to amplify the source and play through the vehicle speakers. Pushing the AUX button will change the mode to auxiliary device if the AUX jack is connected. NOTE: The AUX device must be turned on and the device’s volume set to proper level.
UNDERSTANDING YOUR INSTRUMENT PANEL This radio has a hard drive. CD’s can be ripped to the hard drive, and the map data comes loaded on the hard drive. Refer to your “Navigation User’s Manual” for detailed operating instructions. Operating Instructions — Satellite Radio Refer to your “Navigation User’s Manual” for detailed operating instructions. Clock Setting Procedure The GPS receiver used in this system is synchronized to the time data being transmitted by the GPS satellite.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: When you are traveling and enter a new time zone, the cluck must be reset manually for the new zone. Changing Daylight Savings Time 1. Highlight the box next to “Time” and press ENTER. 2. Select Daylight Savings when Daylight Savings Time is in effect or Select Standard if Daylight Savings Time is not being observed. press ENTER. 3. Select “Done” when finished. Select “Done” to exit from the clock setting mode.
UNDERSTANDING YOUR INSTRUMENT PANEL ESN/SID Access With RSC Radios With the ignition switch in the ON/RUN or ACCESSORY position and the radio ON, press the SETUP button and scroll using the TUNE control knob until Sirius ID is selected. Press the TUNE control knob and the Sirius ID number will be displayed. The Sirius ID number display will time out in 2 minutes. Press any button on the radio to exit this screen.
UNDERSTANDING YOUR INSTRUMENT PANEL remain tuned to the new channel until you make another selection. Holding either button will bypass channels without stopping until you release it. SCAN Button Pressing the SCAN button causes the tuner to search for the next channel, pausing for 8 seconds before continuing to the next. To stop the search, press SCAN a second time. INFO Button Pressing the INFO button will cycle between Artist, Song Title, and Composer (if available) information.
UNDERSTANDING YOUR INSTRUMENT PANEL SET Button — To Set the Push-Button Memory When you are receiving a channel that you wish to commit to push-button memory, press the SET button. The symbol SET 1 will now show in the display window. Select the button (1-6) you wish to lock onto this channel and press and release that button. If a button is not selected within 5 seconds after pressing the SET button, the channel will continue to play but will not be stored into push-button memory.
UNDERSTANDING YOUR INSTRUMENT PANEL VIDEO ENTERTAINMENT SYSTEM — IF EQUIPPED The optional VES™ (Video Entertainment System) includes the following components for rear seat entertainment: 187 • The LCD Screen swings up from the rear of the armrest to allow the rear seat passenger(s) to view the display. • A diagonal seven-inch liquid crystal display (LCD) screen integrated into the center console armrest. The screen features brightness control for optimum daytime and nighttime viewing.
UNDERSTANDING YOUR INSTRUMENT PANEL • Two wireless infrared headsets allow rear seat passengers to listen to the same or individual audio sources. • Audio/Video RCA Jacks (AUX Jacks) on the rear of the center console enable the monitor to display video directly from a video camera, connect video games for display on the screen or play music directly from an MP3 player. REMOTE SOUND SYSTEM CONTROLS — IF EQUIPPED The remote sound system controls are located on the rear surface of the steering wheel.
UNDERSTANDING YOUR INSTRUMENT PANEL 189 The button located in the center of the right hand control will switch modes to Radio or CD. If you press the switch up or down twice it plays the second track, three times, it will play the third, etc. The left hand control is a rocker type switch with a push button in the center. The function of the left hand control is different depending on which mode you are in.
UNDERSTANDING YOUR INSTRUMENT PANEL 7. Do not store the disc where temperatures may become too high. CLIMATE CONTROLS The Climate Control System allows you to balance the temperature, amount, and direction of air circulating throughout the vehicle. The controls are located on the instrument panel, below the radio. Manual Air Conditioning and Heating System The controls for the heating/air conditioning and ventilation system in this vehicle consist of a series of outer rotary dials inner push knobs.
UNDERSTANDING YOUR INSTRUMENT PANEL The instrument panel features four airflow registers. Two registers are located on the outer ends of the instrument panel and two are located in the center of the instrument panel. These registers can be fully closed to partially block airflow, and they can be adjusted to direct airflow where the occupant desires. Blower Control There are four blower speeds. Use this control to regulate the amount of air forced through the system in any mode you select.
UNDERSTANDING YOUR INSTRUMENT PANEL Mode Control (Air Direction) Mode control allows you to choose from several patterns of air distribution. You can select either a primary mode, as identified by the symbols, or a blend of two of these modes. The closer the control is to a particular mode, the more air distribution you receive from that mode. Panel Mode Air is directed through the outlets in the instrument panel. These outlets can be adjusted to direct air flow.
UNDERSTANDING YOUR INSTRUMENT PANEL This dehumidifies the air to help dry the windshield. To improve fuel economy, use these modes only when necessary. Recirculation Control Use this button to choose between outside air intake or recirculation of the air inside the vehicle. A lamp will illuminate when you are in recirculate mode. Only use the recirculate mode to temporarily block out any outside odors, smoke, or dust and to cool the interior rapidly upon initial start up in very hot or humid weather.
UNDERSTANDING YOUR INSTRUMENT PANEL Air Conditioning Operation Use this button to engage the Air Conditioning. A lamp will illuminate when the Air Conditioning System is engaged NOTE: The air conditioning compressor will not engage until the engine has been running for about 10 seconds. MAX A/C For maximum cooling use the A/C and recirculate buttons at the same time.
UNDERSTANDING YOUR INSTRUMENT PANEL Operation of the system is quite simple. 1. Turn the Mode Control knob (on the right) and the Blower Control knob (on the left) to AUTO. NOTE: The AUTO position performs best for front seat occupants only. 195 Automatic Blower Control To engage the Automatic Temperature Control, turn the Blower Control Knob Indicator to AUTO. 2. Dial in the temperature you would like the system to maintain by rotating the Temperature Control knob.
UNDERSTANDING YOUR INSTRUMENT PANEL Air conditioning in this system is automatic. Pressing the Air Conditioning Control button while in AUTO mode will cause the LED in the control button to flash three times and then turn off. This indicates that the system is in AUTO mode and requesting the air conditioning is not necessary.
UNDERSTANDING YOUR INSTRUMENT PANEL • In cold weather, use of the Recirculation mode may lead to excessive window fogging. The Recirculation mode is not allowed in the Mix and Defrost modes to improve window clearing operation. Recirculation will be disabled automatically if these modes are selected. • Extended use of recirculation may cause the windows to fog. If the interior of the windows begins to fog, press the Recirculation button to return to outside air.
UNDERSTANDING YOUR INSTRUMENT PANEL Auto Climate Controls Chart
UNDERSTANDING YOUR INSTRUMENT PANEL The operator can override the AUTO mode setting to change airflow distribution by rotating the Mode Control knob (on the right) to one of the following positions. Panel Mode Air is directed through the outlets in the instrument panel. These outlets can be adjusted to direct air flow. Bi-Level Mode Air is directed through the panel and floor outlets.
UNDERSTANDING YOUR INSTRUMENT PANEL Vacation Storage Anytime you store your vehicle, or keep it out of service (i.e. vacation) for two weeks or more, run the air conditioning system at idle for about five minutes in the fresh air and high blower setting. This will insure adequate system lubrication to minimize the possibility of compressor damage when the system is started again. Window Fogging Interior fogging on the windshield can be quickly removed by turning the mode selector to Defrost.
UNDERSTANDING YOUR INSTRUMENT PANEL 201 Control Setting Suggestions for Various Weather Conditions 4
UNDERSTANDING YOUR INSTRUMENT PANEL Electric Rear Window Defroster Press this button, located on the Blower Control knob, to turn on the rear window defroster and the heated side mirrors — if equipped. A light in the button will illuminate to indicate the rear window defroster is ON. The defroster automatically turns off after about 10 minutes of operation.
STARTING AND OPERATING CONTENTS 䡵 Starting Procedures . . . . . . . . . . . . . . . . . . . . 207 ▫ Brake/Transaxle Interlock System . . . . . . . . . . 212 ▫ Automatic Transaxle . . . . . . . . . . . . . . . . . . . 207 ▫ Automatic Transaxle Ignition Interlock System . . . . . . . . . . . . . . . . . . . . . . 212 ▫ Normal Starting . . . . . . . . . . . . . . . . . . . . . . 207 ▫ Tip Start Feature — Automatic Transaxle Only . . . . . . . . . . . . . . . . . . . . . . .
STARTING AND OPERATING 䡵 Electronic Brake Control System – ABS/TCS/BAS/ESP . . . . . . . . . . . . . . . . . . . . 221 ▫ Anti-Lock Brake System (ABS) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 221 䡵 Tires — General Information . . . . . . . . . . . . . . 235 ▫ Tire Pressure . . . . . . . . . . . . . . . . . . . . . . . . . 235 ▫ Tire Inflation Pressures . . . . . . . . . . . . . . . . . 236 ▫ Radial-Ply Tires . . . . . . . . . . . . . . . . . . . . . .
STARTING AND OPERATING 205 ▫ General Information . . . . . . . . . . . . . . . . . . . 248 ▫ Ethanol Fuel (E-85) . . . . . . . . . . . . . . . . . . . . 254 䡵 Tire Chains . . . . . . . . . . . . . . . . . . . . . . . . . . . 248 ▫ Fuel Requirements . . . . . . . . . . . . . . . . . . . . 254 䡵 Snow Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . 248 ▫ Selection Of Engine Oil For Flexible Fuel Vehicles (E-85) And Gasoline Vehicles . . . . . . . 255 䡵 Tire Rotation Recommendations . . . .
STARTING AND OPERATING ▫ Loading . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260 ▫ Towing Requirements . . . . . . . . . . . . . . . . . . 265 䡵 Trailer Towing . . . . . . . . . . . . . . . . . . . . . . . . 261 ▫ Towing Tips . . . . . . . . . . . . . . . . . . . . . . . . . 269 ▫ Common Towing Definitions . . . . . . . . . . . . . 261 䡵 Recreational Towing (Behind Motorhome, Etc.) . . . . . . . . . . . . . . . . 270 ▫ Trailer Hitch Classification . . . . . . . . . . . . . . .
STARTING AND OPERATING STARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belt. Make sure all occupants have securely fastened their seat belts. WARNING! Never leave children alone in a vehicle. Leaving children in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Don’t leave the keys in the ignition.
STARTING AND OPERATING start within 15 seconds, turn the ignition switch to the “OFF” position, wait 10 to 15 seconds, then repeat the normal starting procedure. WARNING! Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transaxle cannot be started this way. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle.
STARTING AND OPERATING engine is flooded. Leave the ignition key in the ON position, release the accelerator pedal and repeat the “NORMAL STARTING” procedure. WARNING! Never pour fuel or other flammable liquid into the throttle body air inlet opening in an attempt to start the vehicle. This could result in flash fire causing serious personal injury. CAUTION! To prevent damage to the starter, do not crank the engine for more than 15 seconds at a time. Wait 10 to 15 seconds before trying again.
STARTING AND OPERATING cycle, the key must be cycled to the ignition RUN position and then repeat the start sequence. To shut off the vehicle when it is in Remote Start mode, press the remote start button once. In order to avoid inadvertent shut downs, the one-time press to shut down the vehicle will be disabled for two seconds after receipt of a valid remote start request.
STARTING AND OPERATING AUTOMATIC TRANSAXLE 211 • Shift into or out of REVERSE only after the vehicle has come to a complete stop and the engine is at idle speed. • Do not shift from REVERSE, PARK, or NEUTRAL into any forward gear when the engine is above idle speed. • Before shifting into any gear, make sure your foot is firmly on the brake pedal. NOTE: You MUST press and hold the brake pedal down while shifting out of Park.
STARTING AND OPERATING Brake/Transaxle Interlock System This system prevents you from moving the gear shift out of Park and into any gear unless the brake pedal is pressed. This system is active only while the ignition switch is in the ON or ACC positions. Always depress the brake pedal first, before moving the gear selector out of PARK. NOTE: If a malfunction occurs, the transaxle will not shift out of park. Battery power is required to release the brake/transaxle interlock system.
STARTING AND OPERATING • Stop the vehicle and shift into Park (P). • Turn the key to OFF then restart the engine. • Shift into the desired range and resume driving. NOTE: Even if the transaxle can be reset, it is recommended that you visit a dealer at your earliest possible convenience. Your dealer has diagnostic equipment to determine if the problem could recur. If the transaxle cannot be reset, dealer service is required.
STARTING AND OPERATING “3” Drive This range eliminates shifts into Overdrive. The transaxle will operate normally in First, Second and Third while in this range. The “3” position should also be used when descending steep grades to prevent brake system distress. NOTE: Using the “3” range while operating the vehicle under heavy operating conditions will improve performance and extend transaxle life by reducing excessive shifting and heat build up.
STARTING AND OPERATING 215 AutoStick姞 Operation By placing the selector lever one shift level below the ⬙D⬙ position, it can be moved from side to side. This allows the driver to select a higher or lower range of gears. Moving the selector lever to the Left (-) triggers a downshift and to the Right (+) an upshift. The gear position will display in the instrument cluster on the transaxle range indicator. • Starting out in second gear is helpful in snowy or icy conditions.
STARTING AND OPERATING • If the system detects a problem it will disable the AutoStick威 mode and the transaxle will return to the automatic mode until the problem is corrected. place the gear selector in REVERSE. For vehicles equipped with automatic transaxles, place the gear selector in the PARK position. PARKING BRAKE When the parking brake is applied with the ignition on, the Brake Light in the instrument cluster will come on.
STARTING AND OPERATING NOTE: When parking on a hill, it is important to set the parking brake before placing the gear selector in Park, otherwise the load on the automatic transaxle locking mechanism may make it difficult to move the selector out of Park. As an added precaution, turn the front wheels toward the curb on a downhill grade and away from the curb on a uphill grade. NOTE: You should always apply the parking brake before leaving the vehicle. WARNING! • Never leave children alone in a vehicle.
STARTING AND OPERATING If either of the two hydraulic systems lose normal capability, the remaining system will still function with some loss of overall braking effectiveness. This will be evident by increased pedal travel during application and greater pedal force required to slow or stop. In addition, if the malfunction is caused by an internal leak, as the brake fluid in the master cylinder drops, the brake warning indicator will light.
STARTING AND OPERATING WARNING! • Anti-lock system (ABS) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded. • The ABS cannot prevent accidents, including those resulting from excessive speed in turns, following another vehicle too closely, or hydroplaning. Only a safe, attentive, and skillful driver can prevent accidents.
STARTING AND OPERATING ABS is activated during braking under certain road or stopping conditions. ABS-inducing conditions can include ice, snow, gravel, bumps, railroad tracks, loose debris, or panic stops.
STARTING AND OPERATING ELECTRONIC BRAKE CONTROL SYSTEM – ABS/TCS/BAS/ESP Your vehicle may be equipped with an optional advanced electronic brake control system that includes Anti-Lock Brake System (ABS), Traction Control System (TCS), Brake Assist System (BAS) and Electronic Stability Program (ESP). All systems work together to enhance vehicle stability and control in various driving conditions and are commonly referred to as ESP.
STARTING AND OPERATING WARNING! • BAS cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded. • The BAS cannot prevent accidents, including those resulting from excessive speed in turns, following another vehicle too closely, or hydroplaning. Only a safe, attentive, and skillful driver can prevent accidents.
STARTING AND OPERATING WARNING! • Electronic Stability Program (ESP) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. • ESP cannot prevent accidents, including those resulting from excessive speed in turns, driving on very slippery surfaces, or hydroplaning. Only a safe, attentive, and skillful driver can prevent accidents.
STARTING AND OPERATING WARNING! In the Partial ESP mode, the engine torque reduction and stability features are desensitized. Therefore, the enhanced vehicle stability offered by ESP is unavailable. NOTE: To improve the vehicle’s traction when driving with snow chains, or starting off in deep snow, sand or gravel, it may be desirable to switch to the “Partial Off” mode by pressing the ESP switch.
STARTING AND OPERATING POWER STEERING The standard power steering system will give you good vehicle response and increased ease of maneuverability in tight spaces. The system will provide mechanical steering capability if power assist is lost. If for some reason the power assist is interrupted, it will still be possible to steer your vehicle. Under these conditions, you will observe a substantial increase in steering effort, especially at very low vehicle speeds and during parking maneuvers.
STARTING AND OPERATING DRIVING ON SLIPPERY SURFACES Acceleration Rapid acceleration on snow covered, wet, or other slippery surfaces may cause the front wheels to pull erratically to the right or left. This phenomenon occurs when there is a difference in the surface traction under the front (driving) wheels. WARNING! Rapid acceleration on slippery surfaces is dangerous. Unequal traction can cause sudden pulling of the front wheels. You could lose control of the vehicle and possibly have an accident.
STARTING AND OPERATING TIRE SAFETY INFORMATION Tire Markings 227 • European Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter ⬙P⬙ is absent from this tire size designation. Example: 215/65R15 96H • LT (Light Truck)-Metric tire sizing is based on U.S. design standards.
STARTING AND OPERATING Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ⴖ....blank....ⴖ = Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary Spare tire 31 = Overall Diameter in Inches (in) 215 = Section Width in Millimeters (mm) 65 = Aspect Ratio in Percent (%) —Ratio of section height to section width of tire. 10.
STARTING AND OPERATING 229 EXAMPLE: Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry. H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions. —The maximum speed corresponding to the Speed Symbol should only be achieved under specified operating conditions (i.e. tire pressure, vehicle loading, road conditions, and posted speed limits).
STARTING AND OPERATING Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire; however, the date code may only be on one side. Tires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire. Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the outboard side then you will find it on the inboard side of the tire.
STARTING AND OPERATING Tire Loading and Tire Pressure 231 Tire and Loading Information Placard Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on either the face of the driver’s door or the driver’s side “B” pillar.
STARTING AND OPERATING Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the “Tire and Loading Information” placard and in the “Vehicle Loading” section of this manual.
STARTING AND OPERATING 6. If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle. NOTE: The following table shows examples on how to calculate total load, cargo/luggage, and towing capacities of your vehicle with varying seating configurations 233 and number and size of occupants.
STARTING AND OPERATING
STARTING AND OPERATING WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle. Three primary areas are affected by improper tire pressure: 235 1.
STARTING AND OPERATING 2. Economy— Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Under inflation, also increases tire rolling resistance and results in higher fuel consumption. 3. Ride Comfort and Vehicle Stability— Proper tire inflation contributes to a comfortable ride. Over inflation produces a jarring and uncomfortable ride.
STARTING AND OPERATING CAUTION! After inspecting or adjusting the tire pressure, always reinstall the valve stem cap (if equipped). This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressures specified on the placard are always “cold tire inflation pressure.” Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or driven less than 1 mile (1 km) after a 3 hour period.
STARTING AND OPERATING WARNING! High speed driving with your vehicle under maximum load is dangerous. The added strain on your tires could cause them to fail. You could have a serious accident. Don’t drive a vehicle loaded to the maximum capacity at continuous speeds above 75 mph (120 km/h). Cuts and punctures in radial tires are repairable only in the tread area because of sidewall flexing. Consult your authorized tire dealer for radial tire repairs.
STARTING AND OPERATING 239 Do not install a wheel cover or attempt to mount a conventional tire on the compact spare wheel, since the wheel is designed specifically for the compact spare. Limited Use Spare — If Equipped The limited use spare tire is for temporary emergency use on your vehicle. This tire is identified by a limited use spare tire warning label located on the limited use spare tire and wheel assembly.
STARTING AND OPERATING WARNING! Prolonged use of limited use spare, or incorrect tire size of front wheel, may damage the transaxle differential and result in loss of vehicle mobility and could result in loss of vehicle control. Tire Spinning When stuck in mud, sand, snow, or ice conditions, do not spin your vehicle’s wheels above 30 mph (48 km/h) for more than 30 seconds continuously. Refer to: “Freeing A Stuck Vehicle” in Section 6 of this manual for additional information.
STARTING AND OPERATING Life of Tire The service life of a tire is dependent upon varying factors including but not limited to: • Driving style • Tire pressure • Distance driven WARNING! Tires and spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure. You could lose control and have an accident resulting in serious injury or death.
STARTING AND OPERATING WARNING! CAUTION! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle. This can cause unpredictable handling and stress to steering and suspension components. You could lose control and have an accident resulting in serious injury or death.
STARTING AND OPERATING TIRE PRESSURE MONITORING SYSTEM (TPMS) — IF EQUIPPED Base Tire Pressure Monitoring System (TPMS) Operation – If Equipped This is the Tire Pressure Monitoring System warning indicator located in the instrument cluster. • The Tire Pressure Monitoring System (TPMS) will warn the driver of a low tire pressure based on the vehicle recommended cold placard pressure. • The tire pressure will vary with temperature by about 1 psi (6.9 kPa) for every 12 °F (6.5 °C).
STARTING AND OPERATING sufficiently low enough to turn ON the “Tire Pressure Monitoring Light”. Driving the vehicle may cause the tire pressure to rise to approximately 30 psi (207 kPa), but the “Tire Pressure Monitoring Light” will still be ON. In this situation, the “Tire Pressure Monitoring Light” will turn OFF only after the tires have been inflated to the vehicle’s recommended cold placard pressure value.
STARTING AND OPERATING 245 graphic display of the pressure value(s) will stop flashing, and the Tire Pressure Monitoring Lamp will extinguish once the updated tire pressure(s) have been received. The vehicle may need to be driven for up to 10 minutes above 15 mph (25 km/h) to receive this information. Low Tire Pressure Display NOTE: A low spare tire will not cause the Tire Pressure Monitoring Telltale Lamp to illuminate or the chime to sound.
STARTING AND OPERATING Check TPM System Display If the ignition key is cycled, this sequence will repeat, providing the system fault still exists. If the system fault no longer exists, the Tire Pressure Monitoring Telltale Light will no longer flash, and the ⬙CHECK TPM SYSTEM⬙ text message will no longer display. NOTE: If your vehicle is equipped with a compact spare wheel and tire assembly it does not have a tire pressure monitoring sensor.
STARTING AND OPERATING CAUTION! The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equipment that is not of the same size, type, and/or style. Aftermarket wheels can cause sensor damage. Do not use tire sealant from a can, or balance beads if your vehicle is equipped with a TPMS, as damage to the sensors may result.
STARTING AND OPERATING General Information This device complies with part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired operation. The tire pressure sensors are covered under one of the following licenses: United States . . . . . . . . . . . . . . . . . . . . . KR5S120123 Canada . . . . . . . . . .
STARTING AND OPERATING Snow tires generally have lower speed ratings than what was originally equipped with your vehicle and should not be operated at sustained speeds over 75 mph (120 km/h). Tire Rotation Recommendations Tires on the front and rear axles of vehicles operate at different loads and perform different steering, driving and braking functions. For these reasons, they wear at unequal rates, and tend to develop irregular wear patterns. These effects can be reduced by timely rotation of tires.
STARTING AND OPERATING FUEL REQUIREMENTS 2.4L and 2.7L ENGINES Your vehicle is designed to meet all emission regulations and provide excellent fuel economy when using high quality regular unleaded gasoline with an octane rating of 87. The use of premium gasoline is not recommended. The use of premium gasoline will provide no benefit over high quality regular gasoline, can impair engine performance and may damage the engine. 3.5L ENGINE The 3.
STARTING AND OPERATING Reformulated Gasoline Many areas of the country require the use of cleaner burning gasoline referred to as “Reformulated Gasoline”. Reformulated gasolines contain oxygenates, and are specifically blended to reduce vehicle emissions and improve air quality. The manufacturer supports the use of reformulated gasolines. Properly blended reformulated gasolines will provide excellent performance and durability of engine and fuel system components.
STARTING AND OPERATING MMT In Gasoline MMT is a manganese containing metallic additive that is blended into some gasoline to increase the octane number. Gasolines blended with MMT offer no performance advantage beyond gasolines of the same octane number without MMT. Gasolines blended with MMT have shown to reduce spark plug life and reduce emission system performance in some vehicles. The manufacturer recommends using gasolines without MMT.
STARTING AND OPERATING Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsibility of the manufacturer. NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you. Carbon Monoxide Warnings WARNING! Carbon monoxide (CO) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • Do not inhale exhaust gases.
STARTING AND OPERATING CAUTION! Only vehicles with the E-85 fuel filler door label can operate on E-85. ETHANOL FUEL (E-85) E-85 is a mixture of approximately 85% fuel ethanol and 15% unleaded gasoline. WARNING! Ethanol vapors are extremely flammable and could cause serious personal injury. Never have any smoking materials lit in or near the vehicle when removing the fuel filler tube cap (gas cap) or filling the tank. Do not use E-85 as a cleaning agent and never use it near an open flame.
STARTING AND OPERATING Selection Of Engine Oil For Flexible Fuel Vehicles (E-85) and Gasoline Vehicles Whether operating the vehicle on an E-85 ethanol fuel or unleaded gasoline the engine oil requirements are the same. Refer to “Engine Oil Selection in the “Maintenance Procedures” section of this manual for the proper quality and viscosity engine oil. NOTE: Your engine oil filler cap also describes the correct engine oil to use.
STARTING AND OPERATING ADDING FUEL Fuel Filler Cap (Gas Cap) The gas cap is behind the fuel filler door, on the left rear quarter panel of the vehicle. If the gas cap is lost or damaged, be sure the replacement cap is for use with this vehicle. After removing the gas cap, place the gas cap tether cable over a hook on the inside of the fuel door. This keeps the gas cap suspended away from and protects the vehicle’s surface.
STARTING AND OPERATING CAUTION! Damage to the fuel system or emission control system could result from using an improper fuel tank filler tube cap (gas cap). A poorly fitting cap could let impurities into the fuel system. 257 started. This might indicate a damaged cap. If the problem is detected twice in a row, the system will turn on the Malfunction Indicator Light (MIL). Resolving the problem will turn the MIL light off.
STARTING AND OPERATING NOTE: Tighten the gas cap about 1/4 turn until you hear one click. This is an indication that cap is properly tightened. If the gas cap is not tighten properly, the Malfunction Indicator Light will come on. Be sure the gas cap is tightened every time the vehicle is refueled. WARNING! A fire may result if gasoline is pumped into a portable container that is inside of a vehicle. You could be burned. Always place gas containers on the ground while filling.
STARTING AND OPERATING • Gross Axle Weight Rating (GAWR) rear • Vehicle Identification Number (VIN) • Type of Vehicle • Month Day and Hour of Manufacture (MDH) The bar code allows a computer scanner to read the Vehicle Identification Number (VIN). 259 WARNING! Because the front wheels steer the vehicle, it is important that you do not exceed the maximum front or rear GAWR. A dangerous driving condition can result if either rating is exceeded. You could lose control of the vehicle and have an accident.
STARTING AND OPERATING Overloading can cause potential safety hazards and shorten useful service life. Heavier axles or suspension components do not necessarily increase the vehicle’s GVWR. Loading To load your vehicle properly, first figure out its empty weight, axle by axle and side by side. Store heavier items down low and be sure you distribute their weight as evenly as possible. Stow all loose items securely before driving.
STARTING AND OPERATING TRAILER TOWING In this section you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle. Before towing a trailer carefully review this information to tow your load as efficiently and safely as possible. To maintain warranty coverage, follow the requirements and recommendations in this manual concerning vehicles used for trailer towing.
STARTING AND OPERATING Gross Combination Weight Rating (GCWR) The gross combination weight rating (GCWR) is the total permissible weight of your vehicle and trailer when weighed in combination. (Note that GCWR ratings include a 150 lbs (68 kg) allowance for the presence of a driver). Gross Axle Weight Rating (GAWR) The GAWR is the maximum capacity of the front and rear axles. Distribute the load over the front and rear axles evenly. Make sure that you do not exceed either front or rear GAWR.
STARTING AND OPERATING Trailer Hitch Classification The following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition. Refer to the Trailer Towing Weights (Maximum Trailer Weight Ratings) chart for the Max. GTW towable for your given drivetrain. 263 Trailer Hitch Classification Class Max. GTW (Gross Trailer Wt.
STARTING AND OPERATING CAUTION! Towing a trailer with a larger than recommended frontal area could cause the engine to overheat or cause severe engine damage under extreme conditions. Trailer and Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% of the Gross Trailer Weight (GTW) on the tow hitch of your vehicle.
STARTING AND OPERATING must be considered as part of the total load on your vehicle. Refer to the Tire and Loading Information placard in the Tire Safety Information Section of this manual for the maximum combined weight of occupants and cargo for your vehicle. 265 Towing Requirements To promote proper break-in of your new vehicle drivetrain components the following guidelines are recommended: CAUTION! CAUTION! Incorrect tongue weight could result in increased yaw or vehicle instability.
STARTING AND OPERATING WARNING! Improper towing can lead to an injury accident. Follow these guidelines to make your trailer towing as safe as possible: Make certain that the load is secured in the trailer and will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control. You could lose control of your vehicle and have an accident.
STARTING AND OPERATING − Proper tire inflation pressures are essential to the safe and satisfactory operation of your vehicle. Refer to the Tires–General Information section of this manual on Tire Pressures for proper tire inflation procedures. − Also, check the trailer tires for proper tire inflation pressures before trailer usage. − Check for signs of tire wear or visible tire damage before towing a trailer.
STARTING AND OPERATING WARNING! The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. Do not connect trailer brakes to your vehicle’s hydraulic brake lines. It can overload your brake system and cause it to fail. You might not have brakes when you need them and could have an accident. Towing any trailer will increase your stopping distance.
STARTING AND OPERATING 269 Towing Tips — Automatic Transmission The “D” range can be selected when towing. However, if frequent shifting occurs while in this range, the “3” range should be selected. NOTE: Using the “3” range while operating the vehicle under heavy operating conditions will improve performance and extend transmission life by reducing excessive shifting and heat build up. This action will also provide better engine braking.
STARTING AND OPERATING − When using the speed control, if you experience speed drops greater than 10 mph (16 km/h), disengage until you can get back to cruising speed. If you have any questions or concerns after reviewing this section, please consult your dealer to for full details on the towing capabilities of the vehicle. − Use speed control in flat terrain and with light loads to maximize fuel efficiency. RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.
WHAT TO DO IN EMERGENCIES CONTENTS 䡵 Hazard Warning Flasher . . . . . . . . . . . . . . . . . 272 ▫ Jacking Instructions . . . . . . . . . . . . . . . . . . . . 276 䡵 If Your Engine Overheats . . . . . . . . . . . . . . . . 272 䡵 Jump-Starting Procedures Due To A Low Battery . . . . . . . . . . . . . . . . . . . . . . . . . . 280 ▫ Engine Oil Overheating — 2.4L Engine Only (If Equipped) . . . . . . . . . . . . . . . . . . . . . . . . 273 䡵 Freeing A Stuck Vehicle . . . . . . . . . . . . . . . . .
WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER The flasher switch is located on the instrument panel, below the radio. Depress the switch and both cluster indicators and all front and rear directional signals will flash. Depress the switch again to turn Hazard Warning Flashers off. If it is necessary to leave the vehicle to go for service, the flasher system will continue to operate with the ignition key removed and the vehicle locked.
WHAT TO DO IN EMERGENCIES NOTE: There are steps that you can take to slow down an impending overheat condition. If your air conditioner is on, turn it off. The air conditioning system adds heat to the engine cooling system and turning off the A/C removes this heat. You can also turn the Temperature control to maximum heat, the Mode control to floor, and the fan control to High. This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.
WHAT TO DO IN EMERGENCIES JACKING AND TIRE CHANGING WARNING! • Being under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never put any part of your body under a vehicle that is on a jack. Never start or run the engine while the vehicle is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift. • The jack is designed to use as a tool for changing tires only.
WHAT TO DO IN EMERGENCIES Preparations For Jacking Park the vehicle on a firm level surface, avoid ice or slippery areas, set the parking brake and place the gear selector in PARK (automatic transaxle) or REVERSE (manual transaxle). Turn OFF the ignition. WARNING! Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. 275 • Turn on the Hazard Warning Flasher.
WHAT TO DO IN EMERGENCIES Jacking Instructions 1. Remove the scissors jack and lug wrench from the spare wheel as an assembly. Turn the jack screw to the left to loosen the lug wrench, and remove the wrench from the jack assembly. NOTE: The Jack Handle attaches to the side of the jack with two attachment points. When the jack is partially expanded, the tension between the two attachment points holds the jack handle in place. Removing Jack Handle From Jack 2.
WHAT TO DO IN EMERGENCIES 277 6 Jacking Locations
WHAT TO DO IN EMERGENCIES CAUTION! WARNING! Do not attempt to raise the vehicle by jacking on locations other than those indicated in step 3. Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 3. There are two front jacking locations and two rear jacking locations on each side of the body.
WHAT TO DO IN EMERGENCIES 279 WARNING! WARNING! To avoid possible personal injury, handle the wheel covers with care to avoid contact with any sharp edges. A loose tire or jack thrown forward in a collision or hard stop could endanger the occupants of the vehicle. Always stow the jack parts and the spare tire in the places provided. NOTE: The wheel cover is held on the wheel by the wheel nuts.
WHAT TO DO IN EMERGENCIES JUMP-STARTING PROCEDURES DUE TO A LOW BATTERY Jump-starting remote battery terminals are located under the hood. The battery is stored between the left front head lamp assembly and the left front wheel splash shield. Access is through the splash shield. WARNING! • Take care to avoid the radiator cooling fan whenever the hood is raised. It can start anytime the ignition switch is on. You can be hurt by the fan. • Do not attempt to push or tow your vehicle to get it started.
WHAT TO DO IN EMERGENCIES 1. Wear eye protection and remove any metal jewelry such as watch bands or bracelets that might make an inadvertent electrical contact. 2. When boosting from a battery in another vehicle, park that vehicle within booster cable reach but without letting the vehicles touch. Set parking brake, place automatic transaxle in PARK and turn ignition to OFF for both vehicles. the positive terminal of the booster battery. Refer to the following illustration for jump-starting connections.
WHAT TO DO IN EMERGENCIES 6. If the vehicle is equipped with Sentry Key Immobilizer, turn the ignition switch to the ON position for 3 seconds before moving the ignition switch to the START position. 7. Start the engine in the vehicle that has the booster battery, let the engine idle a few minutes, then start the engine in the vehicle with the discharged battery. 8. When removing the jumper cables, reverse the sequence exactly. Be careful of the moving belts and fan. 9.
WHAT TO DO IN EMERGENCIES WARNING! Fast spinning tires can be dangerous. Forces generated by excessive wheel speeds may cause axle, tire damage or failure. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 30 mph (48 km/h) or for longer than 30 seconds continuously without stopping when you are stuck. And don’t let anyone near a spinning wheel, no matter what the speed.
WHAT TO DO IN EMERGENCIES If it is necessary to use the accessories while being towed (wipers, defrosters, etc.), the key must be in the ON position, not the ACCESSORY position. Make certain the transaxle remains in NEUTRAL. Without The Ignition Key Special care must be taken when the vehicle is towed with the ignition in the LOCK position. A dolly should be used under the front wheels if the rear wheels are raised. Proper towing equipment is necessary to prevent damage to the vehicle.
MAINTAINING YOUR VEHICLE CONTENTS 䡵 2.4L Engine Compartment . . . . . . . . . . . . . . . 287 ▫ Catalytic Converter . . . . . . . . . . . . . . . . . . . . 298 䡵 2.7L Engine Compartment . . . . . . . . . . . . . . . 288 ▫ Crankcase Emission Control System . . . . . . . . 299 䡵 3.5L Engine Compartment . . . . . . . . . . . . . . . 289 ▫ Fuel Filter . . . . . . . . . . . . . . . . . . . . . . . . . . 299 䡵 Onboard Diagnostic System — OBD II . . . . . . 290 ▫ Air Cleaner Element (Filter) . . . . . . . .
MAINTAINING YOUR VEHICLE ▫ Exhaust System . . . . . . . . . . . . . . . . . . . . . . 304 䡵 Replacement Bulbs . . . . . . . . . . . . . . . . . . . . . 321 ▫ Cooling System . . . . . . . . . . . . . . . . . . . . . . . 305 䡵 Bulb Replacement . . . . . . . . . . . . . . . . . . . . . . 322 ▫ Hoses And Vacuum/Vapor Harnesses . . . . . . . 309 ▫ Head Lamp Bulb Replacement . . . . . . . . . . . . 322 ▫ Fuel System Connections . . . . . . . . . . . . . . . . 309 ▫ Fog Lamps . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 287 2.4L ENGINE COMPARTMENT 7 2.
MAINTAINING YOUR VEHICLE 2.7L ENGINE COMPARTMENT 2.
MAINTAINING YOUR VEHICLE 289 3.5L ENGINE COMPARTMENT 7 3.
MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
MAINTAINING YOUR VEHICLE 291 might indicate a damaged cap. If the problem is detected twice in a row, the system will turn on the Malfunction Indicator Light (MIL). Resolving the problem will turn the MIL light off. Your vehicle has a simple ignition key actuated test, which you can use prior to going to the test station.
MAINTAINING YOUR VEHICLE b. The MIL will not flash at all and will remain fully illuminated until you turn off the ignition key or start the engine. This means that your vehicle’s OBD system is ready and you can proceed to the I/M station. If your OBD system is not ready, you should see your authorized dealer or repair facility.
MAINTAINING YOUR VEHICLE WARNING! You can be badly injured working on or around a motor vehicle. Only do service work for which you have the knowledge and the proper equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic. MAINTENANCE PROCEDURES The pages that follow contain the required maintenance services determined by the engineers who designed your vehicle.
MAINTAINING YOUR VEHICLE CAUTION! Do not overfill the engine. Overfilling the engine as indicated by the range markings, as described above, on the engine oil dipstick will cause oil aeration, which can lead to loss of oil pressure and an increase in oil temperature. This could damage your engine. Engine Oil Dipstick — Gasoline Engines Checking the oil while the vehicle is on level ground and only when the engine is hot, will improve the accuracy of the oil level readings.
MAINTAINING YOUR VEHICLE • Trailer towing. • Taxi, Police or delivery service (commercial service). • Off-Road or desert operation. • If equipped for and operating with E-85 (ethanol) fuel. NOTE: If ANY of these apply to you then change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first, and follow schedule “B—All Engines” of the ⬙Maintenance Schedules⬙ section of this manual.
MAINTAINING YOUR VEHICLE Engine Oil Viscosity (SAE Grade) SAE 5W-20 engine oil for 2.4L and 2.7L engines, is recommended for all operating temperatures. SAE 10W-30 engine oil for 3.5L engines, is recommended for all operating temperatures. 5W-20 Oil Viscosity Chart These engine oils are designed to improve low temperature starting and vehicle fuel economy. Refer to the engine oil filler cap for the preferred engine oil viscosity grade for each vehicle.
MAINTAINING YOUR VEHICLE Synthetic Engine Oils There are a number of engine oils being promoted as either synthetic or semi-synthetic. If you chose to use such a product, use only those oils that are American Petroleum Institute (API) Certified and have the recommended SAE viscosity grade. Follow the maintenance schedule that describes your driving type.
MAINTAINING YOUR VEHICLE Catalytic Converter The catalytic converter requires the use of unleaded fuel only. Leaded gasoline will destroy the effectiveness of the catalyst as an emission control device. Under normal operating conditions, the catalytic converter will not require maintenance. However, it is important to keep the engine properly tuned to assure proper catalyst operation and prevent possible catalyst damage.
MAINTAINING YOUR VEHICLE • Do not idle the engine with any ignition coil connectors disconnected for prolonged periods. Crankcase Emission Control System Proper operation of this system depends on freedom from sticking or plugging due to deposits. As vehicle mileage builds up, the PCV valve and passages may accumulate deposits. If a valve is not working properly, replace it with a new valve. DO NOT ATTEMPT TO CLEAN THE OLD PCV VALVE! Check ventilation hose for indication of damage or plugging deposits.
MAINTAINING YOUR VEHICLE Maintenance-Free Battery You will never have to add water, nor is periodic maintenance required. NOTE: The battery is stored in a compartment behind the left front fender and is accessible without removing the tire and wheel. Remote battery terminals are located in the engine compartment for jump starting. To access the battery, turn the steering wheel fully to the right and remove the inner fender shield.
MAINTAINING YOUR VEHICLE CAUTION! It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked positive (+) and negative (-) and identified on the battery case. Cable clamps should be tight on the terminal posts and free of corrosion. Apply grease to posts and clamps after tightening.
MAINTAINING YOUR VEHICLE Refrigerant Recovery and Recycling R-134a Air Conditioning Refrigerant is a hydrofluorocarbon (HFC) that is endorsed by the Environmental Protection Agency and is an ozone-saving product. However, the manufacturer recommends that air conditioning service be performed by dealers or other service facilities using recovery and recycling equipment. NOTE: Use only manufacturer approved A/C System Sealers, Stop Leak Products, Seal Conditioners, Compressor Oil, or Refrigerants.
MAINTAINING YOUR VEHICLE Body Lubrication Locks and all body pivot points, including such items as seat tracks, doors, liftgate and hood hinges, should be lubricated periodically to assure quiet, easy operation and to protect against rust and wear. Prior to the application of any lubricant, the parts concerned should be wiped clean to remove dust and grit; after lubricating excess oil and grease should be removed.
MAINTAINING YOUR VEHICLE 3. Install the new blade assembly onto the wiper arm tip until it locks in place. NOTE: Always refer to the wiper blade packaging for specific installation instructions. Many wiper blade replacements fit multiple vehicles. Windshield Washer Reservoir The washer fluid reservoir is located engine compartment and should be checked for fluid level at regular intervals.
MAINTAINING YOUR VEHICLE Cooling System WARNING! • When working near the radiator cooling fan, disconnect the fan motor lead or turn the ignition switch to the OFF position. The fan is temperature controlled and can start at any time the ignition switch is in the ON position. • You or others can be badly burned by hot coolant or steam from your radiator. If you see or hear steam coming from under the hood, don’t open the hood until the radiator has had time to cool.
MAINTAINING YOUR VEHICLE CAUTION! Mixing of coolants other than specified HOAT engine coolants, may result in engine damage and may decrease corrosion protection. If a non-HOAT coolant is introduced into the cooling system in an emergency, it should be replaced with the specified coolant as soon as possible. Do not use plain water alone or alcohol base engine coolant (antifreeze) products.
MAINTAINING YOUR VEHICLE Please note that it is the owner’s responsibility to maintain the proper level of protection against freezing according to the temperatures occurring in the area where the vehicle is operated. NOTE: Mixing coolant types will decrease the life of the engine coolant and will require more frequent coolant changes.
MAINTAINING YOUR VEHICLE ground. If ingested by a child, contact a physician immediately. Clean up any ground spills immediately. Coolant Level 4 Cylinder Engines — the coolant bottle provides a quick visual method for determining that the coolant level is adequate. With the engine idling and warm to normal operating temperature, the level of the coolant in the bottle should be between the “ADD” and “Full” lines, shown on the bottle.
MAINTAINING YOUR VEHICLE • Maintain coolant concentration at 50% HOAT engine coolant (minimum) and distilled water for proper corrosion protection of your engine which contains aluminum components. • Make sure that the radiator and coolant recovery bottle overflow hoses are not kinked or obstructed. • Keep the front of the radiator clean. If your vehicle is equipped with air conditioning, keep the front of the condenser clean, also. • Do not change the thermostat for summer or winter operation.
MAINTAINING YOUR VEHICLE Brake System In order to assure brake system performance, all brake system components should be inspected periodically. Suggested service intervals can be found in the Maintenance Section. brittle rubber, cracking, tears, cuts, abrasions, and excessive swelling suggest deterioration of the rubber. Particular attention should be made to examining those hose surfaces nearest to high heat sources, such as the exhaust manifold.
MAINTAINING YOUR VEHICLE 311 WARNING! WARNING! Worn brake hoses can burst and cause brake failure. You could have an accident. If you see any signs of cracking, scuffing, or worn spots, have the brake hoses replaced immediately. Use of a brake fluid that may have a lower initial boiling point or unidentified as to specification, may result in sudden brake failure during hard prolonged braking. You could have an accident.
MAINTAINING YOUR VEHICLE Automatic Transaxle The automatic transaxle and differential assembly are contained within a single housing. All automatic transaxles (with the exception of the transaxle with the 3.5L engine, which has no dipstick and is dealer service only) are equipped with a conventional filler tube and dipstick. If fluid is added, it should be added through the dipstick hole in the case.
MAINTAINING YOUR VEHICLE If the fluid level indicates low, add sufficient fluid to bring to the proper level. CAUTION! Do not overfill. Dirt and water in the transaxle can cause serious damage. To prevent dirt and water from entering the transaxle after checking or replenishing fluid, make certain that the dipstick cap is re-seated properly. Special Additives Do not add any materials (other than leak detection dyes) to Automatic transaxle Fluid (ATF).
MAINTAINING YOUR VEHICLE Washing Special Care • Wash your vehicle regularly. Always wash your vehicle in the shade using Mopar Car Wash or a mild car wash soap, and rinse the panels completely with clear water. • If you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month. • If insects, tar or other similar deposits have accumulated on your vehicle, use Mopar Super Kleen Bug and Tar Remover to remove.
MAINTAINING YOUR VEHICLE 315 • Use Mopar touch up paint on scratches as soon as possible. Your dealer has touch up paint to match the color of your vehicle. Cleaning Leather Upholstery Mopar Total Clean is specifically recommended for leather upholstery. Wheel and Wheel Trim Care All wheels and wheel trim, especially aluminum and chrome plated wheels should be cleaned regularly with a mild soap and water to prevent corrosion.
MAINTAINING YOUR VEHICLE YES Essentials威 Fabric Cleaning Procedure – If Equipped YES Essentials威 seats may be cleaned in the following manner: equipped with electric defrosters or the right rear quarter window equipped with the radio antenna. Do not use scrapers or other sharp instruments which may scratch the elements. • Remove as much of the stain as possible by blotting with a clean, dry towel. When cleaning the rear view mirror, spray cleaner on the towel or rag that you are using.
MAINTAINING YOUR VEHICLE 317 Plastic is not as scratch resistant as glass and therefore different lens cleaning procedures must be followed. Replace the belts if they appear frayed or worn or if the buckles do not work properly. To minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. To remove road dirt, wash with a mild soap solution followed by rinsing. Dry with a soft tissue.
MAINTAINING YOUR VEHICLE FUSES/TOTALLY INTEGRATED POWER MODULE (TIPM) A Totally Integrated Power Module is located in the engine compartment near the air cleaner assembly. This center contains cartridge fuses and mini fuses. A label that identifies each component may be printed on the inside of the cover. Refer to the graphic below for FUSES/TIPM location.
MAINTAINING YOUR VEHICLE Cavity Cartridge Mini Fuse Fuse 10 20 Amp Yellow 11 15 Amp Lt Blue 12 20 Amp Yellow 13 20 Amp Yellow 14 10 Amp Red 15 40 Amp Green 16 15 Amp Lt. Blue 17 10 Amp Red 18 40 Amp Green 19 20 Amp Yellow Description CCN Power Locks Power Outlet Ign Run/Acc Inverter Pwr run/Acc Outlet RR IOD CCN/ Interior Lighting RAD Fan Relay Battery Feed IGN Run/Acc Cigar Ltr/Sunroof IOD Feed Mod-Wcm ASD Relay Contact PWR Feed PWR Amp 1 & Amp 2 Feed Cavity Cartridge Mini Fuse Fuse 20 15 Amp Lt.
MAINTAINING YOUR VEHICLE Cavity Cartridge Mini Fuse Fuse 30 20 Amp Yellow 31 10 Amp Red 32 30 Amp Pink 33 10 Amp Red 34 30 Amp Pink 35 40 Amp Green 36 30 Amp Pink 37 15 Amp Lt. Blue Description Heated Seats Headlamp Washer Relay Control ENG ASD Control Feed 1 ABS MOD/J1962 Conn/PCM ABS Valve Feed ABS Pump Feed Headlamp Washer Control 110 Inverter CAUTION! • When installing the Totally Integrated Power Module cover, it is important to ensure the cover is properly positioned and fully latched.
MAINTAINING YOUR VEHICLE VEHICLE STORAGE If you will not be using your vehicle for more than 21 days you may want to take steps to preserve your battery. You may: • Disengage the mini fuse in the Power Distribution Center labeled IOD (Ignition Off-Draw). • Or, disconnect the negative cable from the battery. REPLACEMENT BULBS All the inside bulbs are brass or glass wedge base. Aluminum base bulbs are not approved and should not be used for replacement.
MAINTAINING YOUR VEHICLE BULB REPLACEMENT Head Lamp Bulb Replacement 1. Open the hood and remove the two head lamp mounting screws. 3. Gently pry the head lamp assembly away from the fender as shown in the picture. This will free the ball stud from its retainer in the fender. Pull the head lamp assembly away from the vehicle. Gently Pry Out Head Lamp Removing Head Lamp For Bulb Replacement 4. Rotate bulb and connector1⁄4 turn counterclockwise. 2.
MAINTAINING YOUR VEHICLE CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. 6. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol. 7. Reinsert the bulb and socket assembly and rotate clockwise1⁄4turn to secure. 323 3. Rotate bulb and connector1⁄4turn counterclockwise. 4. Pull bulb off of connector and replace with a new one. CAUTION! Do not touch the new bulb with your fingers.
MAINTAINING YOUR VEHICLE Tail Lamps, Rear Turn Signals And Backup Lamps — Replacement The tail lamps are a two piece design. The turn signal, brake and tail lamps are located in the rear corner body panel housing. The back up and tail lamps are located in the trunk lid housing. Changing the Rear Corner Tail Lamp Bulbs 1.
MAINTAINING YOUR VEHICLE 2. Remove the two plastic wing nuts from the tail lamp housing. 325 Changing the Trunk Lid Tail Lamps 1. With the trunk lid open, unplug the lamp assembly. 7 Location Plastic Wing Nuts 3. Grasp the tail lamp and pull firmly outward pushing gently on the studs from inside to disengage the lamp housing. 4. Twist and remove socket from lamp. 5. Remove bulb from socket and replace. Trunk Lid Tail Lamp 2. Remove and replace the bulb. 3.
MAINTAINING YOUR VEHICLE License Plate Lamp — Rear Center High-Mounted Stop Lamp 1. Remove two retaining screws holding the lamp lens in place. 1. Open the trunk lid to find the centrally located highmounted stop lamp. Location and Removal of Rear License Lamp Lens High-mounted Stop Lamp Bulb Replacement 2. Gently pry the lens loose. 2. Twist and remove socket from lamp. 3. Pull bulb from socket, replace and reattach the lamp lens with the two retaining screws. 3.
MAINTAINING YOUR VEHICLE 327 FLUIDS AND CAPACITIES Fuel (approximate) 2.4L, 2.7L and 3.5 Liter Engine Engine Oil with Filter 2.4 Liter Engine (SAE 5W-20, API Certified) 2.7 Liter Engine (SAE 5W-20, API Certified) 3.5 Liter Engine (SAE 10W-30, API Certified) Cooling System * 2.4 Liter Engine (Mopar威 Antifreeze/Coolant 5 Year/100,000 Mile Formula) or equivalent. 2.7 Liter Engine (Mopar威 Antifreeze/Coolant 5 Year/100,000 Mile Formula) or equivalent. 3.
MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS, AND GENUINE PARTS Engine Component Engine Coolant Engine Oil (2.4 & 2.7 Liter) Engine Oil (3.5 Liter) Oil Filter (2.4 Liter) Oil Filter (2.7 & 3.5 Liter) Spark Plugs Fuel Selection (2.4 & 2.7 Liter) Fuel Selection (3.5 Liter) Fluids, Lubricants, and Genuine Parts Mopar威 Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) or equivalent Use API Certified engine oil. SAE 5W-20 is recommended.
MAINTAINING YOUR VEHICLE 329 Chassis Component Automatic Transmission Brake Master Cylinder Power Steering Reservoir Fluids, Lubricants and Genuine Parts Mopar威 ATF+4 Automatic Transmission Fluid. Mopar威 DOT 3 and SAE J1703 should be used. If DOT 3 brake fluid is not available, then DOT 4 is acceptable. Use only recommended brake fluids. Mopar威 ATF+4 Automatic Transmission Fluid.
MAINTENANCE SCHEDULES CONTENTS M A I N T E N A N C E 䡵 Emission Control System Maintenance . . . . . . 332 ▫ Schedule “B” . . . . . . . . . . . . . . . . . . . . . . . . 335 䡵 Maintenance Schedules . . . . . . . . . . . . . . . . . . 332 ▫ Schedule “A” . . . . . . . . . . . . . . . . . . . . . . . .
M A I N T E N A N C E 332 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
MAINTENANCE SCHEDULES NOTE: If ANY of these apply to you then change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first and follow schedule “B” of the ⬙Maintenance Schedules⬙ section of this manual. NOTE: If ANY of these apply to you then change your coolant every 102,000 miles (170 000 km) or 60 months, whichever comes first and follow schedule “B” of the ⬙Maintenance Schedules⬙ section of this manual. Second is Schedule “A”.
M A I N T E N A N C E 334 S C H E D U L E S • Change the engine oil filter. 8 MAINTENANCE SCHEDULES • Check the fluid levels of coolant reservoir, brake/ clutch master cylinder, and manual transaxle and add as needed. • Check all lights and all other electrical items for correct operation. • Check the manual transmission fluid level (if equipped). • Check the coolant level, hoses, and clamps. CAUTION! At Each Oil Change • Inspect the exhaust system. • Inspect the brake hoses.
SCHEDULE “B” Schedule “B” Follow schedule “B” if you usually operate your vehicle under one or more of the following conditions. • Day or night temperatures are below 32° F (0° C). • Stop and go driving. • Extensive engine idling. • Driving in dusty conditions. • Short trips of less than 10 miles (16 km). • More than 50% of your driving is at sustained high speeds during hot weather, above 90° F (32° C). • Trailer towing. 335 M A I N T • Off-road or desert operation.
M 336 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and oil filter, or at 3 months, A whichever comes first. N C Inspect engine air cleaner filter, replace if necesE sary. S C H E D U L E S 8 Rotate tires. Check spare tire for proper pressure and correct stowage.
SCHEDULE “B” Miles (Kilometers) Change engine oil and oil filter, or at 3 months, whichever comes first. Replace the air cleaner filter. Rotate tires. Check spare tire for proper pressure and correct stowage. Inspect brake linings. Replace Spark Plugs: 2.
M 338 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and oil filter, or at 3 months, A whichever comes first. N C Inspect engine air cleaner filter, replace if necesE sary. S C H E D U L E S 8 Rotate tires. Check spare tire for proper pressure and correct stowage. Inspect brake linings.
SCHEDULE “B” Miles (Kilometers) Change engine oil and oil filter, or at 3 months, whichever comes first. Replace engine air cleaner filter. Rotate tires. Check spare tire for proper pressure and correct stowage. Inspect brake linings. Change Automatic Transaxle Fluid and Filter. Replace Spark Plugs: 2.4L Engine Flush and replace engine coolant at 60 months, or 102,000 miles (170 000 km) whichever comes first.
M 340 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and oil filter, or at 3 months, A whichever comes first. N C Inspect engine air cleaner filter, replace if necesE sary. S C H E D U L E S 8 Rotate tires. Check spare tire for proper pressure and correct stowage. Inspect brake linings.
SCHEDULE “B” Miles (Kilometers ) Change engine oil and oil filter, or at 3 months, whichever comes first. Replace engine air cleaner filter. Rotate tires. Check spare tire for proper pressure and correct stowage. Inspect brake linings. Replace Spark Plugs: 2.
M 342 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and oil filter, or at 3 months, A whichever comes first. N C Replace engine air cleaner filter. E Rotate tires. S C H E D U L E S 8 Check spare tire for proper pressure and correct stowage. Replace Spark Plugs: 2.7L and 3.5L Engines Flush and replace engine coolant if not done at 60 months. (Flush and replace engine coolant at 60 months, or 102,000 miles (170 000 km) whichever comes first.
SCHEDULE “B” Miles (Kilometers) Change engine oil and oil filter, or at 3 months, whichever comes first. Replace engine air cleaner filter. Rotate tires. Check spare tire for proper pressure and correct stowage. Inspect brake linings. Change Automatic Transaxle Fluid and Filter. Replace Spark Plugs: 2.4L Engine Replace the accessory drive belt every 120,000 miles (200 000 km).
M 344 SCHEDULE “A” A I Schedule “A” N T Miles E N (Kilometers) A [Months] N C Change engine oil and oil filter. E Replace engine air cleaner filter. S C H E D U L E S 8 Rotate tires. Check spare tire for proper pressure and correct stowage. Inspect brake linings. Replace Spark Plugs: 2.
SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and oil filter. Replace engine air cleaner filter. Rotate tires. Check spare tire for proper pressure and correct stowage. Inspect brake linings. Flush and replace engine coolant at 60 months, if not replaced at 102,000 miles (170 000 km). Replace Spark Plugs: 2.
M 346 SCHEDULE “A” A I N Miles T (Kilometers) E N [Months] A Change engine oil and oil filter. N C Replace engine air cleaner filter. E Rotate tires. S C H E D U L E S 8 Check spare tire for proper pressure and correct stowage. Inspect brake linings. Replace Spark Plugs: 2.
SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and oil filter. Replace engine air cleaner filter. Rotate tires. Check spare tire for proper pressure and correct stowage. Inspect brake linings. Change Automatic Transaxle Fluid and Filter. Flush and replace engine coolant, 102,000 miles (170 000 km) if not done at 60,000 miles Replace Spark Plugs: 2.4L Engine Replace Spark Plugs: 2.7L and 3.5L Engines Replace the accessory drive belt every 120,000 miles (200 000 km).
M A I N T E N A N C E S C H E D U L E S 8 348 SCHEDULE “A” Inspection and service should also be performed anytime a malfunction is observed or suspected. Retain all receipts. WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS 䡵 Suggestions For Obtaining Service For Your Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . 350 ▫ Prepare For The Appointment . . . . . . . . . . . . 350 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . . . 350 䡵 Reporting Safety Defects . . . . . . . . . . . . . . . . . 353 ▫ In Canada . . . . . . . . . . . . . . . . . . . . . . . . . . 353 䡵 Publication Order Forms . . . . . . . . . . . . . . . . . 353 ▫ Be Reasonable With Requests . . .
IF YOU NEED CONSUMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty, discuss additional charges with the service manager. Keep a maintenance log of your vehicle’s service history. This can often provide a clue to the current problem.
IF YOU NEED CONSUMER ASSISTANCE • If for some reason you are still not satisfied, talk to the general manager or owner of the dealership. They want to know if you need assistance. • If your dealership is unable to resolve the concern, you may contact the Manufacturer’s Customer Center.
IF YOU NEED CONSUMER ASSISTANCE Service Contract You may have purchased a service contract for your vehicle to help protect you from the high cost of unexpected repairs after your manufacturer’s new vehicle limited warranty expires. The manufacturer stands behind only the manufacturer’s Service Contracts. If you purchased a manufacturer’s Service Contract, you will receive Plan Provisions and an Owner Identification Card in the mail within three weeks of your vehicle delivery date.
IF YOU NEED CONSUMER ASSISTANCE REPORTING SAFETY DEFECTS In the 50 United States and Washington D.C.: If you believe that your vehicle has a defect, which could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying the manufacturer. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
IF YOU NEED CONSUMER ASSISTANCE Corporation vehicles. A complete working knowledge of the vehicle, system, and/or components is written in straightforward language with illustrations, diagrams, and charts. • Diagnostic Procedure Manuals. Filled with diagrams, charts and detailed illustrations, these practical manuals make it easy for students and technicians to find and fix problems on computercontrolled vehicle systems and features.
IF YOU NEED CONSUMER ASSISTANCE Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and a half (1 1/2) times as well on the government course as a tire graded 100.
IF YOU NEED CONSUMER ASSISTANCE WARNING! The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, under inflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure.
INDEX 10
INDEX ABS (Anti-Lock Brake System) . . . . . . . . . . . . . 218 Adding Engine Coolant (Antifreeze) . . . . . . . . . 306 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . 256 Adding Washer Fluid . . . . . . . . . . . . . . . . . . . . 111 Additives, Fuel . . . . . . . . . . . . . . . . . . . . . . . . 252 Air Cleaner, Engine (Engine Air Cleaner Filter) . . . . . . . . . . . . . . . . 299 Air Conditioner Maintenance . . . . . . . . . . . . . . 301 Air Conditioning . . . . . . . . . . . .
INDEX Keyless Transmitter Replacement (RKE) . . . . . 20 Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300 Body Mechanism Lubrication . . . . . . . . . . . . . . 303 B-Pillar Location . . . . . . . . . . . . . . . . . . . . . . . 231 Brake Assist System . . . . . . . . . . . . . . . . . . . . . 221 Brake, Parking . . . . . . . . . . . . . . . . . . . . . . . . . 216 Brake System . . . . . . . . . . . . . . . . . . . . . . . 217,310 Anti-Lock (ABS) . . . . . . . . . . . . . . . . . . . .
INDEX Coin Holder . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 Compact Disc (CD) Maintenance . . . . . . . . . . . 189 Compact Spare Tire . . . . . . . . . . . . . . . . . . . . . 238 Compass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150 Compass Calibration . . . . . . . . . . . . . . . . . . . . 151 Compass Variance . . . . . . . . . . . . . . . . . . . . . . 151 Computer, Trip/Travel . . . . . . . . . . . . . . . . . . . 149 Console . . . . . . . . . . . . . . . . . . .
INDEX Electrical Power Outlets . . . . . . . . . . . . . . . 124,125 Electronic Speed Control (Cruise Control) . . . . . 113 Electronic Stability Program (ESP) . . . . . . . . . . 222 Electronic Vehicle Information Center (EVIC) . . 147 Emergency, In Case of Jacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 274 Jump Starting . . . . . . . . . . . . . . . . . . . . . . . . 280 Towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 283 Emergency Trunk Release . . . . . . . . . . . .
INDEX Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . 255 Replacement Parts . . . . . . . . . . . . . . . . . . . . 255 Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 255 Flooded Engine Starting . . . . . . . . . . . . . . . . . . 208 Floor Console . . . . . . . . . . . . . . . . . . . . . . . . . . 128 Fluid Capacities . . . . . . . . . . . . . . . . . . . . . . . . 327 Fluid Leaks . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX General Information . . . . . . . . . . . . . . . . . 14,95,248 General Maintenance . . . . . . . . . . . . . . . . . . . . 293 Glass Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . 316 Gross Axle Weight Rating . . . . . . . . . . . . . . 259,262 Gross Vehicle Weight Rating . . . . . . . . . . . . 259,261 GVWR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 259 Hands-Free Phone (UConnect™) . . . . . . . . . . . . 73 Hazard Warning Flasher . . . . . . . . . . . . . . . . . .
INDEX Jump Starting . . . . . . . . . . . . . . . . . . . . . . . . . 280 Key, Programming . . . . . . . . . . . . . . . . . . . . . . . Key, Replacement . . . . . . . . . . . . . . . . . . . . . . . Key, Sentry (Immobilizer) . . . . . . . . . . . . . . . . . . Key-In Reminder . . . . . . . . . . . . . . . . . . . . . . . . Keyless Entry System (Sedan) . . . . . . . . . . . . . . Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Knee Bolster . . . . . . . . . . . . . . . . . . .
INDEX 365 Theft Alarm (Security Alarm) . . . . . . . . . . . . 140 Traction Control . . . . . . . . . . . . . . . . . . . . . . 222 Turn Signal . . . . . . . . . . . . . . . . . 105,108,144,324 Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140 Warning (Instrument Cluster Description) . . . 139 Loading Vehicle . . . . . . . . . . . . . . . . . . . . . 258,260 Capacities . . . . . . . . . . . . . . . . . . . . . . . . . . . 260 Tires . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Octane Rating, Gasoline (Fuel) . . . . . . . . . . . . . 250 Odometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142 Trip . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142,143 Oil, Engine . . . . . . . . . . . . . . . . . . . . . . . . . 293,328 Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . 327 Change Interval . . . . . . . . . . . . . . . . . . . . . . 294 Checking . . . . . . . . . . . . . . . . . . . . . . . . . . . 293 Disposal . . . . . . . . . . .
INDEX Programming Transmitters (Remote Keyless Entry) . . . . . . . . . . . . . . 20,115,119 Radial Ply Tires . . . . . . . . . . . . . . . . . . . . . . . . 238 Radio Broadcast Signals . . . . . . . . . . . . . . . . . . 158 Radio, Navigation . . . . . . . . . . . . . . . . . . . . . . 181 Radio Operation . . . . . . . . . . . . . . . . . . . . . . . 188 Radio, Satellite . . . . . . . . . . . . . . . . . . . . . . 182,183 Rear Cup Holder . . . . . . . . . . . . . . . . . . . . . . .
INDEX Child Restraint . . . . . . . . . . . . . . . . . . . . . . 54,61 Extender . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Front Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Pretensioners . . . . . . . . . . . . . . . . . . . . . . . . . 38 Rear Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Reminder . . . . . . . . . . . . . . . . . . . . . . . . . . . 140 Seat Belts (Sedan) . . . . . . . . . . . . . . . . . . . . . . . 31 Seats . . . . . . . . . .
INDEX Steering Wheel Mounted Sound System Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 321 Storage, Vehicle . . . . . . . . . . . . . . . . . . . . . . . . 200 Stuck, Freeing . . . . . . . . . . . . . . . . . . . . . . . . . 282 Sun Roof . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121 Supplemental Restraint System - Airbag . . . . . . . 40 Synthetic Engine Oil . . . . . . . . . . . . . . . . . . .
INDEX Spare Tire . . . . . . . . . . . . . . . . . . . . . . . . . . . 274 Spinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . 240 Tread Wear Indicators . . . . . . . . . . . . . . . . . . 240 Tongue Weight/Trailer Weight . . . . . . . . . . . . . 264 Towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 261 Disabled Vehicle . . . . . . . . . . . . . . . . . . . . . . 283 Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 263 Recreational . . . . . . . . . . .
INDEX Vacuum/Vapor Harnesses . . . . . . . . . . . . . . . . 309 Vanity Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . 73 Variance, Compass . . . . . . . . . . . . . . . . . . . . . . 151 Vehicle Certification Label . . . . . . . . . . . . . . . . 258 Vehicle Identification Number (VIN) . . . . . . . . . . 6 Vehicle Loading . . . . . . . . . . . . . . . . . . 232,258,260 Vehicle Modifications/Alterations . . . . . . . . . . . . 6 Vehicle Storage . . . . . . . . . . . . . . . . . . . . . .
NOTES
NOTES
NOTES
NOTES
NOTES
