SECTION TABLE OF CONTENTS PAGE 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 2 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 3 4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION CONTENTS 䡵 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 Vehicle Identification Number . . . . . . . . . . . . . . 6 䡵 How To Use This Manual . . . . . . . . . . . . . . . . . 4 䡵 Vehicle Modifications / Alterations . . . . . . . . . . 6 䡵 Warnings And Cautions . . . . . . . . . . . . . . . . . .
INTRODUCTION INTRODUCTION This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a Warranty Information Booklet and various customer oriented documents. You are urged to read these publications carefully. Following the instructions and recommendations in this manual will help assure safe and enjoyable operation of your vehicle.
INTRODUCTION 5 1
INTRODUCTION WARNINGS AND CAUTIONS This manual contains WARNINGS against operating procedures which could result in an accident or bodily injury. It also contains CAUTIONS against procedures which could result in damage to your vehicle. If you do not read this entire manual you may miss important information. Observe all Warnings and Cautions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS 䡵 A Word About Your Keys . . . . . . . . . . . . . . . . . 9 ▫ Central Locking — If Equipped . . . . . . . . . . . .15 ▫ Ignition Key Removal . . . . . . . . . . . . . . . . . . . 9 ▫ Door Ajar Warning . . . . . . . . . . . . . . . . . . . . .15 ▫ Automatic Transaxle Ignition Interlock System . .10 ▫ Automatic (Rolling) Door Locks . . . . . . . . . . . .15 ▫ Key-In-Ignition Reminder . . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ To Use The Panic Alarm . . . . . . . . . . . . . . . . .19 ▫ Seat Belt Pretensioners . . . . . . . . . . . . . . . . . . .30 ▫ To Program Additional Transmitters . . . . . . . . .19 ▫ Enhanced Driver Seat Belt Reminder System (BeltAlert) . . . . . . . . . . . . . . . . . . . . . . . . . . .30 ▫ General Information . . . . . . . . . . . . . . . . . . . .20 ▫ Transmitter Battery Service . . . . . . . . . . . . . . .21 䡵 Vehicle Theft Alarm . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS You can insert the double sided keys into the locks with either side up. 9 Ignition Key Removal 2 The dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys from your dealer. Ask your dealer for these numbers and keep them in a safe place.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: If you try to remove the key before you place the lever in PARK, the key may become trapped temporarily in the key cylinder. If this occurs, rotate the key clockwise slightly, then remove the key as described. If a malfunction occurs, the system may trap the key in the ignition cylinder to warn you that this safety feature is inoperable. The engine can be started and stopped but the key cannot be removed until you obtain service.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE SENTRY KEY — IF EQUIPPED With this system, an electronically coded ignition key sends a signal to the vehicle electronics. If the electronics recognizes the signal, the vehicle will start and continue to run. If the system does not recognize the signal the vehicle will start and run for 2 seconds then shut off.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Replacement Keys NOTE: Only keys that have been programmed to the vehicle electronics can be used to start the vehicle. Once a Sentry Key has been programmed to a vehicle, it can not be programmed to any other vehicle. At the time of purchase, the original owner is provided with a four digit PIN number. This number is required for dealer replacement of keys.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE General Information The Sentry Key system complies with FCC rules part 15. Operation is subject to the following two conditions: 1. this device may not cause harmful interference 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Power Door Locks There is a door lock switch on each front door trim panel located to the front of the door handle. Press this switch to lock or unlock the four doors. Door Lock Plunger If the door lock plunger is down when you shut the door, the door will lock. Therefore, make sure that the keys are not inside the vehicle before closing the door.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Central Locking — If Equipped All vehicle doors are locked with the first turn of the key to the LOCK position. The double activation feature requires you to turn the key in the cylinder lock two times within five seconds to UNLOCK all vehicle doors at once. The Automatic Door Locks can be disabled or re-enabled by performing the following procedure: 1. Close all doors and place the key in the ignition. 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Depress the power door lock switch to lock the doors. Automatic Unlock on Exit — Only Available if Automatic Door Locks are Enabled This feature will unlock all the doors when the driver’s door is opened and the ignition switch is in the LOCK position. This function is disabled as delivered from the factory. Automatic Unlock on Exit can be enabled or disabled by performing the following procedure: 1. Close all doors and place the key in the ignition. 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 “Child Protection” Door Lock System (Rear Doors) To provide a safer environment for small children riding in the rear seat, the rear doors of your vehicle have the “child-protection” door lock system. 2 To use the system, open each rear door and use a key to move the control near the door latch UP to the “Engage” position as shown on the door label. When the system on a door is engaged, that door can be opened only by using the outside door handle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE REMOTE KEYLESS ENTRY — IF EQUIPPED This system allows you to lock or unlock the doors or open the trunk from distances up to 23 feet (7 meters) using a transmitter. You don’t have to point the transmitter at the vehicle to activate the system. 1. Press and hold the Unlock button on the transmitter. 2. Continue to hold the Unlock button, wait at least 4 but no longer than 10 seconds, then press the LOCK button. 3. Release both buttons.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 To lock the doors: The horn will chirp and the headlamps will flash once to acknowledge the lock signal. 2. Continue to hold the Unlock button, wait at least 4 but no longer than 10 seconds, then press the Trunk button. NOTE: The horn chirp can be enabled or disabled by the following procedure: 3. Release both buttons. 1. Press and hold the Lock button on the transmitter. 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Using a currently programmed transmitter, press the Unlock button on the transmitter. Continue to hold the Unlock button, wait at least 4 but no longer than 10 seconds, then press and hold the Panic button for at least one second. Release both buttons simultaneously. You will hear a chime to signal that you can proceed with programming the new transmitter. 3.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 Transmitter Battery Service The recommended replacement batteries are CR2016. 3. Reassemble the transmitter case. Snap the halves together and test transmitter operation. 1. Pry the transmitter halves apart with a dime or similar object. Make sure not to damage the rubber gasket material during removal. VEHICLE THEFT ALARM The system monitors the doors, trunk, and ignition for unauthorized operation.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. The light in the instrument cluster will flash rapidly for 15 seconds. This shows that the system is arming. If the light comes on but does not flash, the system is still armed, but there is a problem in the trunk circuit. After 15 seconds the light will continue to flash slowly. This shows that the system is fully armed. TRUNK LOCK AND RELEASE To disarm the system: Unlock a front door using either the key or the Keyless Entry Transmitter.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE With the ignition ON, the word “deck” will be displayed in place of the odometer display indicating that the trunk is open. The odometer display will reappear once the trunk is closed or if the trip button is depressed. 23 Trunk Internal Emergency Release 2 With the key in lock position or key out, the “deck” will be displayed until the trunk is closed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WINDOWS WARNING! Power Windows Never leave children in a vehicle, with the keys in the ignition switch. Occupants, particularly unattended children, can become entrapped by the power windows while operating the power window switch. Such entrapment may result in serious injury or death. The window controls on the driver’s door operate all windows. Power Window Switches The driver’s window switch has an Auto Down feature.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or in certain open or partially open positions. This is a normal occurrence and can be minimized. If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Research has shown that seat belts save lives, and they can reduce the seriousness of injuries in a collision. Some of the worst injuries happen when people are thrown from the vehicle. Seat belts reduce the possibility of ejection and the risk of injury caused by striking the inside of the vehicle. Everyone in a motor vehicle should be belted at all times. Lap/Shoulder Belts All seating positions in your vehicle are equipped with Lap/Shoulder Belts.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the front seat. 2. The seat belt latch plate is above the back of your seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to make the belt go around your lap. 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up a bit on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision. WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 WARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Seat belt assemblies must be replaced after a collision if they have been damaged (bent retractor, torn webbing, etc.).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seat Belt Pretensioners The seat belts for both front seating positions are equipped with pretensioning devices that are designed to remove any slack from the seat belts in the event of a collision. These devices improve the performance of the seat belt system by assuring that the belt is tight about the occupant early in a collision. Pretensioners work for all size occupants, including those in child restraints.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Within 60 seconds of starting the vehicle, unbuckle and then re-buckle the driver’s seat belt at least three times within 10 seconds, ending with the seat belt buckled. NOTE: Watch for the Seat Belt Warning Light to turn on while unbuckling and off while re-buckling the seat belt. It may be necessary to retract the seat belt. 4. Turn off the engine. A single chime will sound to signify that you have successfully completed the programming.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Driver and Right Front Passenger Supplemental Restraint System (SRS) - Airbag This vehicle may also be equipped with left and right window bags to protect the driver and passengers sitting next to a window. If the vehicle is equipped with window bags, they are located above the side windows. Their covers are also labeled SRS AIRBAG.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Do not put anything on or around the front airbag covers or attempt to manually open them. You may damage the airbags and you could be injured because the airbags are not there to protect you. These protective covers for the airbag cushions are designed to open only when the airbags are inflating. • If your vehicle is equipped with left and right window bags, do not stack luggage or other cargo up high enough to block the location of the window bag.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Children that are not big enough to properly wear the vehicle seat belt (see section on “Child Restraint”) should be secured in the rear seat in child restraints or beltpositioning booster seats. Older children who do not use child restraints or beltpositioning booster seats should ride properly buckled up in the rear seat. Never allow children to slide the shoulder belt behind them or under their arm.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • AIRBAG Readiness Light • Driver Airbag • Passenger Airbag • Steering Wheel and Column • Instrument Panel • Interconnecting Wiring • Knee Impact Bolsters • Left and Right Window Bags Above Side Windows — If Equipped • Left and Right Side Impact Sensors — If Equipped • Driver and Front Passenger Seat Belt Pretensioners How The Airbag System Works • The airbag control module determines if a frontal collision is severe enough to require the airbags to inflate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Ignoring the AIRBAG light in your instrument panel could mean you won’t have the airbags to protect you in a collision. If the light does not come on, stays on after you start the vehicle, or if it comes on as you drive, have the airbag system checked right away. • When the airbag control module detects a collision requiring the airbags, it signals the inflator units. A large quantity of nontoxic gas is generated to inflate the airbags.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE However, if you haven’t healed significantly within a few days, or if you have any blistering, see your doctor immediately. • As the airbags deflate you may see some smoke-like particles. The particles are a normal by-product of the process that generates the nontoxic gas used for airbag inflation. These airborne particles may irritate the skin, eyes, nose, or throat. If you have skin or eye irritation, rinse the area with cool water.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Maintaining Your Airbag System WARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. You could be injured because the airbags are not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the steering wheel hub trim cover or the upper right side of the instrument panel. Do not modify the front bumper, vehicle body structure, or frame.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Children 12 years and under should ride properly buckled up in a rear seat, if available. According to crash statistics, children are safer when properly restrained in the rear seats rather than in the front. WARNING! In a collision, an unrestrained child, even a tiny baby, can become a missile inside the vehicle. The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE airbag unless the airbag is turned off. An airbag deployment could cause severe injury or death to infants in this position. WARNING! • Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint. • A rearward facing child restraint should only be used in a rear seat.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Older Children and Child Restraints Children who weigh more than 20 lbs (9 kg) and who are older than one year can ride forward-facing in the vehicle. Forward-facing child seats and convertible child seats used in the forward-facing direction are for children who weigh 20 to 40 lbs (9 to 18 kg) and who are older than one year. These child seats are also held in the vehicle by the lap/shoulder belt or the LATCH child restraint anchorage system.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE LATCH-compatible child restraint systems are now available. However, because the lower anchorages are to be introduced over a period of years, child restraint systems having attachments for those anchorages will continue to also have features for installation using the vehicle’s seat belts. Child restraints having tether straps and hooks for connection to the top tether anchorages have been available for some time.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Again, carefully follow the installation instructions that were provided with the child restraint system. The rear seat lower anchorages are round bars, located at the rear of the seat cushion where it meets the seat back, and are just visible when you lean into the rear seat to install the child restraint. You will easily feel them if you run your finger along the intersection of the seatback and seat cushion surfaces.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE installing the child restraint buckle the seat belt so the seat belt is tucked behind the child restraint and out of reach. If the buckled seat belt interferes with the child restraint installation, instead of tucking the seat belt behind the child restraint, route the seat belt through the child restraint belt path and then buckle it. This should stow the seat belt out of the reach of an inquisitive child.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Child restraint tether strap attachment 1. Rotate the cover over the anchor directly behind the seat where you are placing the child restraint. 45 between the two posts. If not possible, lower the head restraint and pass the tether strap around the outboard side of the head restraint. 3. Attach the tether strap hook (A) of the child restraint to the anchor (B) and remove slack in the tether strap according to the child restraint manufacturer’s instructions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Pets should be restrained in the rear seat in pet harnesses or pet carriers that are secured by seat belts. ENGINE BREAK-IN RECOMMENDATIONS The engine in your new vehicle does not require a long break-in period. Drive moderately during the first 300 miles (500 km). After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • To avoid drawing exhaust gases into the vehicle, close the trunk while driving. However, if for some reason it must remain open, close all windows. Adjust the heating or cooling system to force outside air into the vehicle. Set the blower at high speed. Safety Checks You Should Make Inside the Vehicle Seat Belts Inspect the belt system periodically, checking for cuts, frays and loose parts. Damaged parts must be replaced immediately.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 3 䡵 Console Features . . . . . . . . . . . . . . . . . . . . . . .52 ▫ Manual Front Seat Adjustments . . . . . . . . . . . .57 ▫ Console Features — Without Heated Seats . . . .52 ▫ Power Seats — If Equipped . . . . . . . . . . . . . . .58 ▫ Console Features — With Heated Seats . . . . . . .53 ▫ Heated Seats — If Equipped . . . . . . . . . . . . . .59 䡵 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Automatic Headlights—If Equipped . . . . . . . . .65 ▫ To Deactivate . . . . . . . . . . . . . . . . . . . . . . . . .71 ▫ Daytime Running Lights (Canada Only) . . . . . .66 ▫ To Resume Speed . . . . . . . . . . . . . . . . . . . . . .71 ▫ Lights-On Reminder . . . . . . . . . . . . . . . . . . . .66 ▫ To Vary The Speed Setting . . . . . . . . . . . . . . . .71 ▫ Fog Lights — If Equipped . . . . . . . . . . . . . . . .66 ▫ To Accelerate For Passing . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 51 ▫ Venting Sunroof - Express . . . . . . . . . . . . . . . .79 ▫ Sunroof Maintenance . . . . . . . . . . . . . . . . . . . .79 ▫ Sunshade Operation . . . . . . . . . . . . . . . . . . . .79 ▫ Sunroof Fully Closed . . . . . . . . . . . . . . . . . . . .80 ▫ Wind Buffeting . . . . . . . . . . . . . . . . . . . . . . . .79 䡵 Electrical Power Outlet . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONSOLE FEATURES Console Features — Without Heated Seats The center console/armrest has a pencil /tire gage holder and a tissue holder mounted on the underside of the cover. The bottom of the console bin also has built in holders for compact discs or cassette tapes. There are also two cup holders for rear seat passengers located directly in the back of the center console. Two coin holders are located toward the front of the inside of the console bin.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Console Features — With Heated Seats Console The front console has two cup holders. An optional removable ashtray may be located in the driver’s side cup holder. 53 The center console/armrest has a pencil /tire gage holder and a tissue holder mounted on the underside of the cover. The bottom of the console bin also has built in holders for compact discs or cassette tapes. The power outlet is also mounted inside the center console (if equipped).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Day/Night Mirror— If Equipped Adjust the mirror to center on the view through the rear window. A two point pivot system allows for horizontal and vertical mirror adjustment. Automatic Dimming Mirror— If Equipped This mirror will automatically adjust for annoying headlight glare from vehicles behind you. Push in the button on the face of the mirror to activate the dimming feature.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 55 CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean. 3 Electric Remote-Control Mirrors— If Equipped Both of the outside mirrors can be adjusted by using the remote controls mounted on the instrument panel to the left of the steering wheel.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Outside Mirror — Driver’s Side Adjust the outside mirror to center on the adjacent lane of traffic, with a slight overlap of the view obtained on the inside mirror. Outside Mirror — Passenger’s Side Adjust the convex outside mirror so you can just see the side of your vehicle in the part of the mirror closest to the vehicle. Illuminated Vanity Mirrors — If Equipped An illuminated vanity mirror is on each sun visor.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE SEATS Manual Front Seat Adjustments Forward/Rearward The adjusting bar is at the front of the seats, near the floor. Pull the bar up to move the seat to the desired position. 57 Reclining Bucket Seats The recliner control is on the side of the seat. To recline, lean forward slightly before lifting the lever, then lean back to the desired position and release the lever. Lean forward and lift the lever to return the seatback to its normal position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Lumbar Support — If Equipped This feature allows you to increase or decrease the amount of lumbar support. The control lever is located on the inboard side of the driver’s seatback. Turn the control lever forward to increase and rearward to decrease the desired amount of lumbar support. Power Seats — If Equipped The power seat switches are on the outboard side of the seat near the floor.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 59 Heated Seats — If Equipped WARNING! Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion or other physical condition must exercise care when using the seat heater. It may cause burns even at low temperatures, especially if used for long periods of time. Do not place anything on the seat that insulates against heat, such as a blanket or cushion.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Adjustable Head Restraints Head restraints can reduce the risk of whiplash injury in the event of impact from the rear. Adjust the restraints so that the upper edge is as high as practical. To raise, pull up on the head restraint. To lower, depress the button on the post guide and push down on the head restraint. Adjustable Head Restraint Folding Rear Seat To provide additional storage area, the rear seatback can be folded forward.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 61 WARNING! The cargo area in the rear of the vehicle (with the rear seatbacks in the locked-up or folded down position) should not be used as a play area by children when the vehicle is in motion. They could be seriously injured in an accident. Children should be seated and using the proper restraint system. TO OPEN AND CLOSE THE HOOD To open the hood, two latches must be released.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! If the hood is not fully latched it could fly up when the vehicle is moving and block your forward vision. You could have a collision. Be sure all hood latches are fully latched before driving. LIGHTS Hood Safety Catch Use the hood prop rod to secure the hood in the open position. Place the upper end of the prop rod in the hole marked “prop” on the underside of the hood. To prevent possible damage, do not slam the hood to close it.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Dimmer Control With the parking lights or headlights on, rotating the dimmer control for the interior lights on the Multi-Function Control Lever upward will increase the brightness of the instrument panel lights. Dome Light Position Rotate the dimmer control completely upward to the second detent to turn on the interior lights. The interior lights will remain on when the dimmer control is in this position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Front Map/Reading Lights — If Equipped These lights are mounted between the sun visors. Each light has a push-on push-off switch. Multi-Function Control Lever NOTE: The lights will remain on until the switch is pressed a second time, so be sure that they have been turned off before leaving the vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Headlights, Parking Lights, Instrument Panel Lights Turn the end of the Multi-Function lever to the first detent for parking light operation. Turn to the second detent for headlight operation. 65 the courtesy lights. Turning the dimmer control to the full down position prevents the courtesy lights from coming on when a door is opened. Automatic Headlights—If Equipped This system automatically turns your headlights on at a preset level of outdoor lighting.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Daytime Running Lights (Canada Only) The headlights come on at a low intensity level whenever the ignition switch is turned on. The lights remain on until the ignition switch is turned OFF or the parking brake is engaged. The headlight switch must be used for normal night time driving. Lights-on Reminder If the headlights or parking lights are on after the ignition is turned off, a chime will sound when the driver’s door is opened.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 67 If the headlights are turned off before the ignition, they will turn off in the normal manner. turned OFF and the blades cannot return to the OFF position, damage to the wiper motor may occur. WINDSHIELD WIPERS AND WASHERS The wipers and washers are operated by a switch in the right side control lever. Turn the end of the control lever to select the desired wiper speed. To use the washer, pull the lever toward you and hold while spray is desired.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Mist Use this feature when weather conditions make occasional usage of the wipers necessary. Pull down and release the control lever for a single wiping cycle. Speed Sensitive Intermittent Wiper System Use the intermittent wiper when weather conditions make a single wiping cycle, with a variable pause between cycles, desirable. Turn the lever to the delay position, then select the delay interval.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 69 WARNING! Tilting the steering column while the vehicle is moving is dangerous. Without a stable steering column, you could lose control of the vehicle and have an accident. Adjust the column only while the vehicle is stopped. Be sure it is locked before driving.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ELECTRONIC SPEED CONTROL— IF EQUIPPED When engaged, this device will control the throttle operation to maintain a constant vehicle speed between 30 mph (48 km/h) and 85 mph (137 km/h). The controls are on the steering wheel. in use. The CRUISE Indicator in the instrument cluster will light up when the Speed Control is ON. NOTE: You must press the ON button to activate the system each time the engine is started.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Deactivate: A soft tap on the brake pedal, pushing the CANCEL button, or normal brake or clutch pressure will deactivate speed control without erasing the memory. Pushing the ON/OFF button or turning off the ignition turns the speed control system off and erases the memory. To Resume Speed: To resume a previously set speed, push and release the RESUME/ACCEL button. Resume can be used at any speed above 25 mph (40 km/h).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE When Climbing A Hill If vehicle speed drops 3 mph (5 km/h) below the Speed Control set speed, the transaxle will downshift to third gear. Under severe conditions the transaxle may downshift again to second gear. The transaxle will upshift to fourth gear after the vehicle has reached the top of the hill. When Descending A Hill If vehicle speed rises 3 mph (5 km/h) over the Speed Control set speed, the transaxle will downshift to third gear.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE GARAGE DOOR OPENER — IF EQUIPPED The HomeLink威 Universal Transceiver replaces up to three remote controls (hand held transmitters) that operate devices such as garage door openers, motorized gates, or home lighting. It triggers these devices at the push of a button. The Universal Transceiver operates off your vehicle’s battery and charging system; no batteries are needed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Vehicle exhaust contains carbon monoxide, a dangerous gas. Do not run the vehicle’s exhaust while training the transceiver. Exhaust gas can cause serious injury or death. 3. Choose one of the three Universal Transceiver buttons to program. Place the hand held controller one to three inches from the Universal Transceiver while keeping its indicator light in view.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 5. The indicator light in the Universal Transceiver will begin to flash, first slowly and then rapidly. The rapid flashing indicates successful programming. If after 90 seconds the indicator light does not flash rapidly or goes out, return to step 1 and repeat the procedure. To train the other buttons, repeat steps 3 and 4. Be sure to keep your hand held transmitters in case you need to retrain the Universal Transceiver.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 1. Locate the training button on the garage door motor head unit. The exact location and color of the button may vary by garage door opener manufacturer. If you have difficulty in locating the training button, check your garage door opener manual, or call 1-800-355-3515 or, on the Internet, at www.homelink.com. Your garage door opener should now recognize your Universal Transceiver.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Operation Press and hold the desired button on the Universal Transceiver until the garage door or other device begins to operate. The light in the display shows that the signal is being transmitted. The hand held transmitter may also be used at any time. Reprogramming A Single Button 1. Press and hold the Universal Transceiver button to be reprogrammed. Do not release until step 4 has been completed. 2.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE POWER SUNROOF — IF EQUIPPED The sunroof controls are mounted between the sun visors on the overhead console. Power Sunroof Controls WARNING! • Never leave children in a vehicle, with the keys in the ignition switch. Occupants, particularly unattended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Opening Sunroof - Manual Press the switch rearward and hold, and the sunroof will open automatically from any position. The sunroof will open fully, then stop automatically. During this operation, any release of the sunroof switch will stop the sunroof. Opening Sunroof - Express Press the switch rearward and release, and the sunroof will open automatically from any position. The sunroof will open fully, then stop automatically. This is called Express Open.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Sunroof Fully Closed Press and hold the switch forward until the sunroof stops completely to ensure that the sunroof is fully closed. ELECTRICAL POWER OUTLET The power outlet is located in the lower center of your instrument panel. If your vehicle is equipped with heated seats, a second power outlet is located inside the center console. All accessories connected to any outlet should be removed or turned off when the vehicle is not in use.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 Instruments And Controls . . . . . . . . . . . . . . . . .85 䡵 Radio General Information . . . . . . . . . . . . . . . .98 䡵 Instrument Cluster Standard . . . . . . . . . . . . . . .86 ▫ Radio Broadcast Signals . . . . . . . . . . . . . . . . . .98 䡵 Instrument Cluster Premium . . . . . . . . . . . . . . .87 ▫ Two Types Of Signals . . . . . . . . . . . . . . . . . . .98 䡵 Instrument Cluster Description . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Tuning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99 ▫ Changing Tape Direction . . . . . . . . . . . . . . . . 103 ▫ Radio Data System (RDS) . . . . . . . . . . . . . . . .99 ▫ Metal Tape Selection . . . . . . . . . . . . . . . . . . . 103 ▫ PTY (Program Type) Button . . . . . . . . . . . . . . 100 ▫ Pinch Roller Release . . . . . . . . . . . . . . . . . . . 103 ▫ Balance . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 䡵 Sales Code RBB—AM/FM Stereo Radio With Cassette Tape Player And CD Changer Capability . . . . . . . . . . . . . . . . . . . . . . . . . . . 108 ▫ Radio Operation . . . . . . . . . . . . . . . . . . . . . . 108 ▫ Mode Button . . . . . . . . . . . . . . . . . . . . . . . . 110 ▫ Scan Button (Radio Mode) . . . . . . . . . . . . . . . 110 ▫ Cassette Player Features . . . . . . . . . . . . . . . . 110 ▫ CD Changer Control Capability — If Equipped . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Electronic Serial Number/Sirius Identification Number (ENS/SID) . . . . . . . . . . . . . . . . . . . . 122 䡵 Remote Sound System Controls — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 125 ▫ Selecting Satellite Mode In RBB, RAH And RBK Radios . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123 ▫ Radio Operation . . . . . . . . . . . . . . . . . . . . . . 126 ▫ Selecting Satellite Mode In RBP, RBU, RAZ, RB1 And RBQ Radios . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 85 INSTRUMENTS AND CONTROLS 4
UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER STANDARD
UNDERSTANDING YOUR INSTRUMENT PANEL 87 INSTRUMENT CLUSTER PREMIUM 4
UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTION 1. Fuel Gauge When the ignition key is in the ON position, the pointer will show the level of fuel remaining in the fuel tank. • There is an Anti-Lock Brake system malfunction or Traction Control system malfunction. • The system has been deactivated to prevent damage to the brake system due to overheated brake temperatures. 2.
UNDERSTANDING YOUR INSTRUMENT PANEL 4. Airbag Light The light comes on and remains on for 6 to 8 seconds as a bulb check when the ignition switch is first turned ON. If the bulb does not come on during starting, have the bulb replaced. If the light stays on, or comes on while driving, have the system checked by an authorized dealer. 5. Tachometer The red area of the scale shows the maximum permissible engine revolutions-per-minute (rpm x 1000) for each gear range.
UNDERSTANDING YOUR INSTRUMENT PANEL resume to full illumination. (See “EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS” in the “MAINTAINING YOUR VEHICLE” section of your Owner Manual for more details). If the bulb does not come on when turning the key from OFF to ON, have the condition checked promptly. Certain conditions such as a loose or missing gas cap or poor fuel quality may illuminate the light after engine start.
UNDERSTANDING YOUR INSTRUMENT PANEL 91 13. Engine Temperature Warning Light This light warns of an overheated engine coolant condition. button a second time to return to the odometer. While in trip mode, press and hold the button for at least 1⁄2 second to reset the trip odometer. 14. Transmission Range Indicator This indicator illuminates to show the automatic transmission gear selection.
UNDERSTANDING YOUR INSTRUMENT PANEL If the ABS light remains on or comes on during driving, it indicates that the Anti-Lock portion of the brake system is not functioning and that service is required, however, the conventional brake system will continue to operate normally provided that the BRAKE warning light is not on. 17. Oil Pressure Light Shows low engine oil pressure. The light will come on and remain on briefly when the ignition is turned on as a bulb check.
UNDERSTANDING YOUR INSTRUMENT PANEL The warning light should be checked frequently to assure that it is operating properly. Turn the ignition key to the RUN position. (Refer to “A Word About Your Keys, Ignition Key Removal” in this manual for an illustration of the ignition positions.) The light should come on. If the light does not come on, have the system checked by an authorized dealer. The light will also come on when the parking brake is applied with the ignition in the RUN position.
UNDERSTANDING YOUR INSTRUMENT PANEL COMPASS, TEMPERATURE, AND TRIP COMPUTER DISPLAY — IF EQUIPPED Reset The following trip conditions can be reset: • AVG ECO (changes to present fuel economy) • ODO • ET To reset only the trip condition currently displayed, press and release the STEP and US/M buttons simultaneously until a chime sounds. To reset all trip conditions, hold down the STEP and US/M buttons simultaneously (about 2 seconds) until a second chime sounds and then release the buttons.
UNDERSTANDING YOUR INSTRUMENT PANEL Trip Conditions Average Fuel Economy (AVG ECO) This display shows the average fuel economy since the last reset. Estimated Range (DTE) This display shows the estimated distance that can be traveled with the fuel remaining in the tank. This estimated distance is based on the most recent trip information: (Average Fuel Economy) x (Fuel Remaining) This display cannot be reset. Present Fuel Economy (ECO) This display shows fuel economy for the last few seconds.
UNDERSTANDING YOUR INSTRUMENT PANEL Automatic Compass Calibration The self-calibrating feature of the compass eliminates the need to calibrate the compass for normal conditions. During a short initial period, the compass may appear erratic and the CAL symbol will appear on the display. After the vehicle has completed at least one complete circle in an area free from large metal objects, calibration will be complete when the CAL symbol is extinguished.
UNDERSTANDING YOUR INSTRUMENT PANEL 97 Outside Temperature If the outside temperature is more than 131°F (55°C), the display will show 131°F. When the outside temperature is less than ⫺40°F (⫺40°C), the display will show ⫺40°F/C. CIGAR LIGHTER/ASHTRAY For a nominal charge your dealer can provide a “smoker’s” package. This package consists of a cigar lighter and an ashtray that utilizes one of the cup holders. ELECTRONIC DIGITAL CLOCK The clock and radio each use the display panel built into the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL To Set The Clock: 1. Use a ballpoint pen or similar object to press the hour (H) or minute (M) buttons on the radio, The time setting will increase each time you press the button. 2. Press any other button to exit from the clock setting mode. Or, it will exit the mode automatically if left alone for 5 or 6 seconds. RADIO GENERAL INFORMATION Radio Broadcast Signals Your new radio will provide excellent reception under most operating conditions.
UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE RAZ—AM/ FM STEREO RADIO WITH CASSETTE TAPE PLAYER, CD PLAYER AND CD CHANGER CONTROLS NOTE: The radio sales code is located on the lower left side of your radio faceplate. 99 Power Switch, Volume Control Press the ON/VOL control to turn the radio on. Turn the volume control clockwise to increase the volume. The volume will be displayed and continuously updated while the button is pressed.
UNDERSTANDING YOUR INSTRUMENT PANEL to give FM receivers user-friendly features, such as Program Service name (PS) and Program Type (PTY). Program Service name is typically used by the broadcaster to display the station’s name or call letters, for example ⬙WNIC⬙. Typically these are 8 characters in length and are displayed by the radio for those stations which are broadcasting this information. PTY (Program Type) is used to characterize the station’s program material, for example ⬙Rock Music⬙.
UNDERSTANDING YOUR INSTRUMENT PANEL Program Type Talk Top 40 Weather Radio Display Talk Top 40 Weather By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to the next frequency station with the same selected PTY name. The PTY function only operates when in the FM mode. The radio display will flash “SEEK” and the selected PTY program type when searching for the next PTY station.
UNDERSTANDING YOUR INSTRUMENT PANEL Scan Button Pressing the SCAN button causes the tuner to search for the next station, in either AM or FM, pausing for 5 seconds at each listenable station before continuing to the next. Pressing the AM/FM button continues the search in the alternate frequency band. To stop the search, press SCAN a second time. To Set The Radio Push-button Memory When you are receiving a station that you wish to commit to push-button memory, press the SET button.
UNDERSTANDING YOUR INSTRUMENT PANEL Press the SEEK button up or down to move the track number to skip forward or backward 1 to 6 selections. Press the SEEK button once to move 1 selection, twice to move 2 selections, etc. Fast Forward (FF) Press the FF button up momentarily to advance the tape in the direction that it is playing. The tape will advance until the button is pressed again or the end of the tape is reached. At the end of the tape, the tape will play in the opposite direction.
UNDERSTANDING YOUR INSTRUMENT PANEL Noise Reduction The Dolby Noise Reduction System* is on whenever the tape player is on, but may be switched off. To turn off the Dolby Noise reduction System: Press the Dolby button (button 2) after you insert the tape. The NR light in the display will go off when the Dolby System is off. The Dolby System is automatically reactivated each time a tape is inserted. * ”Dolby” noise reduction manufactured under license from Dolby Laboratories Licensing Corporation.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: • You may eject a disc with the radio OFF. The ignition switch must be in the ON or ACC position to insert a disc with the radio OFF. • If you insert a disc with the ignition ON and the radio OFF, the CD will automatically be pulled into the CD Player and the display will show the time of day. If you insert a disc with the ignition OFF, the display will show the time of day for about 5 seconds, then go out.
UNDERSTANDING YOUR INSTRUMENT PANEL MODE Press the MODE button to select between the tape player, CD player, or satellite radio (if equipped). Scan Button Press this button to play the first 10 seconds of each track. To stop the scan function, press the button a second time. To select Satellite Radio (if equipped), press the MODE button until the word SIRIUS appears.
UNDERSTANDING YOUR INSTRUMENT PANEL Seek Button Press the SEEK up or down to select another track on the same disc. A SEEK symbol will appear on the display. Fast Forward And Rewind Buttons Press and hold the FF button for fast forward. Press and hold the RW button for fast reverse. The audio output can be heard when fast forward and fast reverse are activated. As a safeguard and to protect your CD player, one of the following warning symbols may appear on your display.
UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE RBB—AM/FM STEREO RADIO WITH CASSETTE TAPE PLAYER AND CD CHANGER CAPABILITY NOTE: The radio sales code is located on the lower left side of your radio faceplate. Radio Operation Power/Volume Control Press the ON/VOL control to turn the radio on. Turn the volume control clockwise to increase the volume. NOTE: Power to operate the radio is supplied through the ignition switch. It must be in the ON or ACC position to operate the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL Seek Press and release the SEEK button to search for the next station in either the AM or FM mode. Press the top of the button to seek up and the bottom to seek down. The radio will remain tuned to the new station until you make another selection. Holding the button will bypass stations without stopping until you release it. Tune Press the TUNE control up or down to increase or decrease the frequency.
UNDERSTANDING YOUR INSTRUMENT PANEL Press the AUDIO button a third time and BAL will be displayed. Press the SEEK + or SEEK – to adjust the sound level from the right or left side speakers. Press the AUDIO button a fourth time and FADE will be displayed. Press the SEEK + or SEEK – to adjust the sound level between the front and rear speakers. Press the AUDIO button again or wait 5 seconds to exit setting tone, balance, and fade. AM/FM Selection Press the AM/FM button to change from AM to FM.
UNDERSTANDING YOUR INSTRUMENT PANEL beginning of the previous selection if the tape is within the first 5 seconds of the current selection. The SEEK symbol appears on the display when Music Search is in operation. Music Search shuts off automatically when a selection has been located. Selective Music Search Press the SEEK button up or down to move the track number to skip forward or backward 1 to 7 selections. Press the SEEK button once to move 1 selection, twice to move 2 selections, etc.
UNDERSTANDING YOUR INSTRUMENT PANEL Push-Button While the CD changer is playing, press the NUMBER 1 push-button or the NUMBER 5 push-button to select a disc numbered higher or lower than the one currently being played. Seek Button Press the SEEK up or down to select another track on the same disc. A SEEK symbol will appear on the display. SCAN Button (CD Mode) Press this button to play the first 10 seconds of each track. To stop the scan function, press the button a second time.
UNDERSTANDING YOUR INSTRUMENT PANEL 113 • Disc inserted upside down Radio Operation • Damaged disc Power/Volume Control Press the ON/VOL control to turn the radio on. Turn the volume control clockwise to increase the volume. • Water condensation on optics SALES CODE RBK—AM/ FM STEREO RADIO WITH CD PLAYER AND CD CHANGER CONTROLS NOTE: Power to operate the radio is supplied through the ignition switch. It must be in the ON or ACC position to operate the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL To Set The Radio Push-Button Memory When you are receiving a station that you wish to commit to push-button memory, press the SET button. SET 1 will show in the display window. Select the “1–5” button you wish to lock onto this station and press and release that button. If a button is not selected within 5 seconds after pressing the SET button, the station will continue to play but will not be locked into push-button memory.
UNDERSTANDING YOUR INSTRUMENT PANEL Time Press the TIME button to change the display between radio frequency and time. General Information This radio complies with Part 15 of FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following conditions: 1. This device may not cause harmful interference, 2. This device must accept any interference received, including interference that may cause undesired operation.
UNDERSTANDING YOUR INSTRUMENT PANEL beginning of the current selection, or return to the beginning of the previous selection if the CD is within the first second of the current selection. EJT — Eject Press the EJT button and the disc will unload and move to the entrance for easy removal. The unit will switch to the radio mode. If you do not remove the disc within 15 seconds, it will be reloaded. The unit will continue in radio mode.
UNDERSTANDING YOUR INSTRUMENT PANEL Mode Button To activate the CD changer, press the MODE button until CD information appears on the display. Disc Up/Program Button 1 Press the DISC up (button 1) button to play the next available disc. Disc Down/Program Button 5 Press the DISC down (button 5) button to play the previous disc. Seek Button Press the SEEK up or down to select another track on the same disc. A SEEK symbol will appear on the display.
UNDERSTANDING YOUR INSTRUMENT PANEL CD HOT will pause the operation. Play can be resumed when the operating temperature is corrected or another MODE is selected.
UNDERSTANDING YOUR INSTRUMENT PANEL 119 NOTE: If your vehicle is not equipped with the CD Changer option, you will not be able to use the Navigation system and the CD Player simultaneously. Always remove the Navigation DVD before inserting another disc. 6 DISC CD CHANGER — IF EQUIPPED The CD changer is located below the radio in the instrument panel. The changer plays only 4 3⁄4 inch (12 cm) discs. The changer holds up to 6 discs.
UNDERSTANDING YOUR INSTRUMENT PANEL 3. Upon insertion, the CD will begin to play, and both the button light and the lights in the corner of the loading slot will illuminate. 4. Repeat the process for loading any additional CDs. The CD player will stop while additional CDs are loaded. Playing Discs The radio will show the CD number, the CD track number, and the Track Time Elapsed while the radio is in the CD mode.
UNDERSTANDING YOUR INSTRUMENT PANEL Press the top of the Seek button once to move to the next randomly selected track. Press the bottom of the Seek button to go back to the beginning of the track. Press button 4 a second time to stop random play. Program Button 5 Press this button to play the previous disc. Time Button Press this button to switch between time of day and CD track time. Changing Modes While in the radio mode, if a cassette is loaded, press the Mode button to switch to the tape mode.
UNDERSTANDING YOUR INSTRUMENT PANEL SATELLITE RADIO — IF EQUIPPED Satellite radio uses direct satellite to receiver broadcasting technology to provide clear digital sound, coast to coast. The subscription service provider is Sirius™ Satellite Radio. This service offers up to 100 channels of music, sports, news, entertainment, and programming for children, directly from its satellites and broadcasting studios.
UNDERSTANDING YOUR INSTRUMENT PANEL ESN/SID Access With RBP, RBU, RAZ, RB1 and RBQ Radios With the ignition switch in the ACCESSORY position and the radio OFF, press the CD Eject and TIME buttons simultaneously for 3 seconds. All twelve ESN/SID numbers will be displayed. The radio will exit the ESN/SID mode when any other button is pushed, the ignition is turned OFF, or 5 minutes has passed since any button was pushed.
UNDERSTANDING YOUR INSTRUMENT PANEL 888-539-7474 to discuss options for channel blocking or unblocking. Please have your ESN/SID information available. one and stop the search. Pressing a pre-set memory button during a music type scan, will call up the memory channel and stop the search. Storing and Selecting Pre-Set Channels In addition to the 10 AM and 10 FM pre-set stations, you may also commit 10 satellite stations to push button memory.
UNDERSTANDING YOUR INSTRUMENT PANEL 125 • Dense tree coverage may interrupt reception in the form of short audio mutes. • Driving under wide bridges or along tall buildings can cause intermittent reception. • Placing objects over or too close to the antenna can cause signal blockage. REMOTE SOUND SYSTEM CONTROLS — IF EQUIPPED The remote sound system controls are located on the rear surface of the steering wheel. Reach behind the wheel to access the switches.
UNDERSTANDING YOUR INSTRUMENT PANEL The left hand control is a rocker type switch with a push-button in the center. The function of the left hand control is different depending on which mode you are in. The following describes the left hand control operation in each mode. Radio Operation Pressing the top of the switch will “Seek” up for the next listenable station and pressing the bottom of the switch will “Seek” down for the next listenable station.
UNDERSTANDING YOUR INSTRUMENT PANEL The button in the center of the left hand switch will cause the CD changer to play the next available disc. CASSETTE TAPE AND PLAYER MAINTENANCE To keep the cassette tapes and player in good condition, take the following precautions: 1. Do not use cassette tapes longer than C-90; otherwise, sound quality and tape durability will be greatly diminished. 2. Keep the cassette tape in its case to protect from slackness and dust when it is not in use.
UNDERSTANDING YOUR INSTRUMENT PANEL 4. Do not use solvents such as benzine, thinner, cleaners, or antistatic sprays. 5. Store the disc in its case after playing. 6. Do not expose the disc to direct sunlight. 7. Do not store the disc where temperatures may become too high. NOTE: If you experience difficulty in playing a particular disc, it may be damaged, oversized, or have theft protection encoding. Try a known good disc before considering disc player service.
UNDERSTANDING YOUR INSTRUMENT PANEL CLIMATE CONTROLS Automatic Temperature Control (ATC) — If Equipped 129 near the windshield glass. The In-Car Temperature Sensor is mounted behind the ATC control panel. These sensors transmit data on sun strength and vehicle interior temperatures to enhance system performance. CAUTION! Do not cover either sensor with any foreign material as improper operation of the system will result.
UNDERSTANDING YOUR INSTRUMENT PANEL Fan Control Use this control to regulate the amount of air forced through the system in any mode you select. Turn the control clockwise to increase fan speed. 61,....to 89,90, Hi, for automatic temperature control. You can select a very hot or cold comfort setting by holding the comfort control until it reaches its highest or lowest levels. In ambient temperatures below 21°C (70°F), fan operation is delayed when the engine is first started.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: The compressor will not engage until the engine has been running for several seconds. Slight changes in engine speed or power may be noticed when the compressor is on. This is a normal occurrence since the compressor will cycle on and off to maintain comfort and improve fuel economy. Recirculate Button Press this button to recirculate the air inside the vehicle. Outside air is prevented from entering the vehicle.
UNDERSTANDING YOUR INSTRUMENT PANEL Bi-Level Air is directed through both the panel and floor outlets. This mode is not recommended when heat is required in very cold temperatures. NOTE: There is a varying difference in temperature between the upper and lower outlets for added comfort. The warmer air goes to the floor outlets. This feature provides improved comfort during sunny but cool conditions.
UNDERSTANDING YOUR INSTRUMENT PANEL maintain a clear windshield and provide sufficient heating. If side window fogging becomes a problem, increase blower speed. The compressor will remain on during these conditions. NOTE: Do not use the recirculated air mode under these conditions as window fogging may occur. Hot Weather Automatic Recirculation The system will automatically recirculate the air inside the vehicle when the interior is very warm. This will provide maximum cooling.
UNDERSTANDING YOUR INSTRUMENT PANEL Operating Tips (ATC only)
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: If the system is in the AUTO mode and the fan control is already rotated fully clockwise or fully counterclockwise, the control may have to be rotated to the middle and then to the desired fan setting for manual adjustment of fan speed. Manual Air Conditioning/Heater Control — If Equipped The Air Conditioning System allows you to balance the temperature, amount, and direction of air circulating throughout the vehicle.
UNDERSTANDING YOUR INSTRUMENT PANEL Slight changes in engine speed or power may be noticed when the air conditioning compressor is on. This is a normal occurrence as the compressor will cycle on and off to maintain comfort and increase fuel economy. NOTE: If your air conditioning performance seems lower than expected, check the front of the air conditioning condenser for an accumulation of dirt or insects. The air conditioning condenser is located in front of the radiator.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Continuous use of the Recirculation mode may make the inside air stuffy and under mild, humid conditions cause windows to fog. Use of this mode for longer than 15 minutes is not recommended. • Panel — Air Conditioning Outside air flows through the air conditioning system and then through the outlets located in the instrument panel.
UNDERSTANDING YOUR INSTRUMENT PANEL • Defrost Air is directed through the windshield and side window demist outlets. Use this mode with maximum fan and temperature settings for best windshield and side window defrosting. NOTE: The air conditioning compressor operates in both Mix and Defrost modes even if the Air Conditioning is not selected. This dehumidifies the air to help dry the windshield.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Do not use the recirculation mode as it will not clear windows under these conditions. Summer Operation Air conditioned vehicles must be protected with a highquality antifreeze coolant to provide proper corrosion protection and to raise the boiling point of the coolant for protection against overheating. A 50 % concentration is recommended.
UNDERSTANDING YOUR INSTRUMENT PANEL Operating Tips (Manual A/C Control Only)
UNDERSTANDING YOUR INSTRUMENT PANEL 141 Outside Air Intake Make sure the air intake, directly in front of the windshield, is free of ice, slush, snow or other obstructions such as leaves. Leaves collected in the air-intake plenum may reduce air flow and plug the plenum water drains.
STARTING AND OPERATING CONTENTS 䡵 Starting Procedures . . . . . . . . . . . . . . . . . . . . 146 ▫ Automatic Transaxle . . . . . . . . . . . . . . . . . . . 146 ▫ Normal Starting . . . . . . . . . . . . . . . . . . . . . . 146 ▫ Extreme Cold Weather (Below -20°F Or -29°C) . . . . . . . . . . . . . . . . . 147 ▫ If Engine Fails To Start . . . . . . . . . . . . . . . . . 148 ▫ After Starting . . . . . . . . . . . . . . . . . . . . . . . . 148 䡵 Battery And Engine Block Heaters — If Equipped . . . . . . . . .
STARTING AND OPERATING 䡵 Tire Safety Information . . . . . . . . . . . . . . . . . . 158 䡵 Snow Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . 175 ▫ Tire Markings . . . . . . . . . . . . . . . . . . . . . . . . 158 䡵 Tire Rotation Recommendations . . . . . . . . . . . 175 ▫ Tire Identification Number (TIN) . . . . . . . . . . 162 䡵 AutoStick — If Equipped . . . . . . . . . . . . . . . . 176 ▫ Tire Loading And Tire Pressure . . . . . . . . . . . 163 ▫ AutoStick Operation . . . . . .
STARTING AND OPERATING 145 ▫ Fuel Requirements . . . . . . . . . . . . . . . . . . . . 182 䡵 Vehicle Loading . . . . . . . . . . . . . . . . . . . . . . . 185 ▫ Selection Of Engine Oil For Flexible Fuel Vehicles (E-85) And Gasoline Vehicles . . . . . . . 182 䡵 Trailer Towing . . . . . . . . . . . . . . . . . . . . . . . . 185 ▫ Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182 ▫ Cruising Range . . . . . . . . . . . . . . . . . . . . . . . 182 ▫ Common Towing Definitions . . . . . .
STARTING AND OPERATING STARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. Automatic Transaxle The gear selector must be in the NEUTRAL or PARK position before you can start the engine. Apply the brakes before shifting to any driving gear. CAUTION! Normal Starting Normal Starting of either a cold or a warm engine does not require pumping or depressing the accelerator pedal.
STARTING AND OPERATING 147 CAUTION! Ignition Key Positions WARNING! Never pour fuel or other flammable liquid into the throttle body air inlet opening in an attempt to start the vehicle. This could result in flash fire causing serious personal injury. Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transaxle cannot be started this way.
STARTING AND OPERATING If Engine Fails to Start If the engine fails to start after you have followed the “NORMAL STARTING” or “EXTREME COLD WEATHER” procedures, it may be flooded. Push the accelerator pedal all the way to the floor and hold it there while cranking the engine. This should clear any excess fuel in case the engine is flooded. CAUTION! To prevent damage to the starter, do not crank the engine for more than 15 seconds at a time. Wait 10 to 15 seconds before trying again.
STARTING AND OPERATING 149 WARNING! WARNING! Remember to disconnect the cord before driving. Damage to the 110-115 volt AC electrical cord could cause electrocution. Unintended movement of a vehicle could injure those in and near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle you should shift the transmission into Park, remove the key from the ignition, and apply the park brake.
STARTING AND OPERATING CAUTION! WARNING! Damage to the transaxle may occur if the following precautions are not observed: • Shift into PARK only after the vehicle has come to a complete stop. • Shift into or out of REVERSE only after the vehicle has come to a complete stop and the engine is at idle speed. • Do not shift from REVERSE, PARK, or NEUTRAL into any forward gear when the engine is above idle speed. • Before shifting into any gear, make sure your foot is firmly on the brake pedal.
STARTING AND OPERATING Four Speed Automatic Transaxle The electronically controlled transaxle provides a precise shift schedule. The transaxle electronics are self calibrating; therefore, the first few shifts on a new vehicle may be somewhat abrupt. This is a normal condition, and precision shifts will develop within a few shift cycles. Reset Mode The transaxle is monitored electronically for abnormal conditions.
STARTING AND OPERATING WARNING! Your vehicle could move and injure you and others if it is not completely in P (Park). Check by trying to move the gearshift lever back and forth without depressing the shift button after you have set it in P. Make sure it is in Park before leaving the vehicle. WARNING! Never use the Park position as a substitute for the parking brake. Always apply the parking brake fully when parked to guard against vehicle movement and possible injury or damage.
STARTING AND OPERATING NOTE: Using the “3” range while operating the vehicle under heavy operating conditions will improve performance, fuel economy, and extend transaxle life by reducing excessive shifting and heat build up. Use the “3” range when descending steep grades to prevent brake system distress. 153 PARKING BRAKE When the parking brake is applied with the ignition on, the brake light in the instrument cluster will come on. NOTE: This light only shows that the parking brake is on.
STARTING AND OPERATING To release the parking brake, apply the brake pedal and pull up on the parking brake lever. Push the release button and lower the lever fully. When parking on a hill, it is important to set the parking brake before placing the gear selector in Park, otherwise the load on the transaxle locking mechanism may make it difficult to move the selector out of Park. As an added precaution, turn the front wheels toward the curb on a downhill grade and away from the curb on a uphill grade.
STARTING AND OPERATING 155 BRAKE SYSTEM Your vehicle is equipped with power assisted brakes as standard equipment. In the event power assist is lost for any reason (for example, repeated brake applications with the engine off), the brakes will still function. The effort required to brake the vehicle will be much greater than that required with the power system operating.
STARTING AND OPERATING During stops where ABS is activated, a vibration of the brake pedal may be felt and associated system noises may be heard. WARNING! Pumping of the brake pedal will diminish the effectiveness of Anti-lock brakes and may lead to an accident. Pumping makes the stopping distance longer. Just press firmly on your brake pedal when you need to slow down or stop.
STARTING AND OPERATING 157 POWER STEERING The power assisted steering system of your vehicle provides mechanical steering capability in the event power assist is lost. If for some reason the hydraulic pressure is interrupted, it will still be possible to steer your vehicle. Under these conditions you will observe a substantial increase in steering effort. TRACTION CONTROL — IF EQUIPPED The Traction Control System will improve acceleration and steering on slippery surfaces by reducing tire spin.
STARTING AND OPERATING • The system has been automatically deactivated to prevent damage to the brake system due to overheated brake temperatures. TIRE SAFETY INFORMATION Tire Markings NOTE: Extended heavy use of Traction Control may cause the system to deactivate and turn on the traction control light located in the instrument cluster. This is to prevent overheating of the brake system and is a normal condition. The system will remain disabled for about 4 minutes until the brakes have cooled.
STARTING AND OPERATING 159 • European Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter ⬙P⬙ is absent from this tire size designation. Example: 215/65R15 96H • Temporary Spare tires are high pressure compact spares designed for temporary emergency use only. Tires designed to this standard have the letter “T” molded into the sidewall preceding the size designation.
STARTING AND OPERATING Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ⴖ....blank....ⴖ = Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary Spare tire 31 = Overall Diameter in Inches (in) 215 = Section Width in Millimeters (mm) 65 = Aspect Ratio in Percent (%) —Ratio of section height to section width of tire. 10.
STARTING AND OPERATING 161 EXAMPLE: Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry. H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions. —The maximum speed corresponding to the Speed Symbol should only be achieved under specified operating conditions. (i.e. tire pressure, vehicle loading, road conditions and posted speed limits).
STARTING AND OPERATING Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire however the date code may only be on one side. Tires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire. Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the outboard side then you will find it on the inboard side of the tire.
STARTING AND OPERATING Tire Loading and Tire Pressure 163 Tire and Loading Information Placard Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on either the face of the driver’s door or the driver’s side “B” pillar.
STARTING AND OPERATING Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the “Tire and Loading Information” placard and in the “Vehicle Loading” section of this manual.
STARTING AND OPERATING 6. If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle. NOTE: The following table shows examples on how to calculate total load, cargo/luggage and towing capacities of your vehicle with varying seating configurations and 165 number and size of occupants.
STARTING AND OPERATING
STARTING AND OPERATING WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES—GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle. Three primary areas are affected by improper tire pressure: 167 1.
STARTING AND OPERATING 2. Economy— Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Underinflation also increases tire rolling resistance and results in higher fuel consumption. 3. Ride Comfort and Vehicle Stability— Proper tire inflation contributes to a comfortable ride. Overinflation produces a jarring and uncomfortable ride.
STARTING AND OPERATING CAUTION! After inspecting or adjusting the tire pressure, always reinstall the valve stem cap–if equipped. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressures specified on the placard are always “cold tire inflation pressure”. Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or driven less than 1 mile (1 km) after a 3 hour period.
STARTING AND OPERATING WARNING! High speed driving with your vehicle under maximum load is dangerous. The added strain on your tires could cause them to fail. You could have a serious accident. Don’t drive a vehicle loaded to the maximum capacity at continuous speeds above 75 mph (120 km/h). Cuts and punctures in radial tires are repairable only in the tread area because of sidewall flexing. Consult your authorized tire dealer for radial tire repairs.
STARTING AND OPERATING Do not install a wheel cover or attempt to mount a conventional tire on the compact spare wheel, since the wheel is designed specifically for the compact spare. Do not install more than one compact spare tire/wheel on the vehicle at any given time. CAUTION! Because of the reduced ground clearance, do not take your vehicle through an automatic car wash with the compact spare installed. Damage to the vehicle may result.
STARTING AND OPERATING Tire Spinning When stuck in mud, sand, snow, or ice conditions, do not spin your vehicle’s wheels above 35 mph (55 km/h). See the paragraph on Freeing A Stuck Vehicle in Section 6 of this manual. Tread Wear Indicators Tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced. WARNING! Fast spinning tires can be dangerous. Forces generated by excessive wheel speeds may cause tire damage or failure.
STARTING AND OPERATING Life of Tire The service life of a tire is dependent upon varying factors including but not limited to: • Driving style • Tire pressure • Distance driven WARNING! Tires and spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure. You could lose control and have an accident resulting in serious injury or death.
STARTING AND OPERATING WARNING! CAUTION! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle. This can cause unpredictable handling and stress to steering and suspension components. You could lose control and have an accident resulting in serious injury or death.
STARTING AND OPERATING 175 TIRE CHAINS Due to limited clearance, tire chains are not recommended. Snow tires generally have lower speed ratings than what was originally equipped with your vehicle and should not be operated at sustained speeds over 75 mph (120 km/h). CAUTION! Tire Rotation Recommendations Tires on the front and rear axles of vehicles operate at different loads and perform different steering, driving and braking functions.
STARTING AND OPERATING Follow the recommended tire rotation frequency for your type of driving found in the “Maintenance Schedules” Section of this manual. More frequent rotation is permissible if desired. The reasons for any rapid or unusual wear should be corrected before rotating. The suggested rotation method is the “forward-cross” shown in the diagram. AUTOSTICK — IF EQUIPPED Autostick is a driver-interactive transaxle that offers manual gear shifting capability to provide you with more control.
STARTING AND OPERATING 177 Autostick General Information • The transaxle will automatically upshift from first to second gear and from second to third gear when engine speed reaches about 6300 RPM. • Downshifts from third to second gear above 66 mph (106 km/h) and from second to first gear above 37 mph (60 km/h) will be ignored. • You can start out in first, second, or third gear. Shifting into fourth gear can occur only after vehicle speed reaches 15 mph (24 km/h).
STARTING AND OPERATING • If the system detects a problem it will disable the Autostick mode and the transaxle will return to the automatic mode until the problem is corrected. FUEL REQUIREMENTS Your vehicle is designed to meet all emission regulations and provide excellent fuel economy when using high quality regular unleaded gasoline with an octane rating of 87. The use of premium gasoline is not recommended.
STARTING AND OPERATING Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with materials called oxygenates such as 10% ethanol, MTBE and ETBE. Oxygenates are required in some areas of the country during the winter months to reduce carbon monoxide emissions. Fuels blended with these oxygenates may be used in your vehicle. CAUTION! DO NOT use gasolines containing Methanol. Use of these blends may result in starting and driveability problems and may damage critical fuel system components.
STARTING AND OPERATING conditions and would result in additional cost. Therefore you should not have to add anything to the fuel. Fuel System Cautions CAUTION! Follow these guidelines to maintain your vehicle’s performance: • The use of leaded gas is prohibited by Federal law. Using leaded gasoline can impair engine performance, or damage the emission control system. • An out-of-tune engine, or certain fuel or ignition malfunctions, can cause the catalytic converter to overheat.
STARTING AND OPERATING • Guard against carbon monoxide with proper maintenance. Have the exhaust system inspected every time the vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side windows fully open. • Keep the trunk closed when driving your vehicle to prevent carbon monoxide and other poisonous exhaust gases from entering the vehicle.
STARTING AND OPERATING Fuel Requirements Your vehicle will operate on both unleaded gasoline with an octane rating of 87, or E-85 fuel, or any mixture of these two. For best results, a refueling pattern that alternates between E-85 and unleaded gasoline should be avoided.
STARTING AND OPERATING Replacement Parts Many components in your Flexible Fuel Vehicle (FFV) are designed to be compatible with ethanol. Always be sure that your vehicle is serviced with correct ethanol compatible parts. 183 ADDING FUEL Fuel Filler Cap (Gas Cap) The gas cap is behind the fuel filler door, on the driver’s side of the vehicle. If the gas cap is lost or damaged, be sure the replacement cap is for use with this vehicle.
STARTING AND OPERATING NOTE: Tighten the gas cap until you hear a “clicking” sound. This is an indication that the gas cap is properly tightened. The Malfunction Indicator Light will come on if the gas cap is not properly secured. Make sure that the gas cap is tightened each time the vehicle is refueled. NOTE: When the fuel nozzle “clicks” or shuts off, the fuel tank is full. NOTE: The fuel tank filler tube may have a restricting door about 50 mm (2 inches) down from the opening.
STARTING AND OPERATING VEHICLE LOADING Vehicle Loading Capacities Front Seat Occupants . . . . . . . . . . . . . . . . . . . . . . . 2 Rear Seat Occupants . . . . . . . . . . . . . . . . . . . . . . . . 3 Luggage . . . . . . . . . . . . . . . . . . . . . . 115 lbs. (52 kg) Rated Vehicle Capacity . . . . . . . . . . . 865 lbs. ( 392 kg) TRAILER TOWING In this section you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle.
STARTING AND OPERATING Gross Combination Weight Rating (GCWR) The gross combination weight rating (GCWR) is the total permissible weight of your vehicle and trailer when weighed in combination. (Note that GCWR ratings include a 68 kg (150 lbs) allowance for the presence of a driver). Gross Axle Weight Rating (GAWR) The GAWR is the maximum capacity of the front and rear axles. Distribute the load over the front and rear axles evenly. Make sure that you do not exceed either front or rear GAWR.
STARTING AND OPERATING Weight-Distributing Hitch A weight-distributing hitch includes a receiver attached to the tow vehicle, plus a removable hitch head and spring bar assembly that fits into the receiver opening and hook up brackets that connect the spring bars to the trailer frame.
STARTING AND OPERATING Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/Transmission Frontal Area Max. GTW (Gross Trailer Wt.) 2.4L Automatic/ 20 Sq. Ft Manual 2.7L Automatic/ 20 Sq. Ft. Manual Refer to local laws for maximum trailer towing speeds.
STARTING AND OPERATING Trailer and Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% to 15% of the Gross Trailer Weight (GTW) on the tow hitch of your vehicle. Loads balanced over the wheels or heavier in the rear can cause the trailer to sway severely side to side which will cause loss of control of vehicle and trailer. Failure to load trailers heavier in front is the cause of many trailer accidents.
STARTING AND OPERATING Towing Requirements To promote proper break-in of your new vehicle drivetrain components the following guidelines are recommended: CAUTION! • Avoid towing a trailer for the first 500 miles (805 km) of vehicle operation. Doing so may damage your vehicle. • During the first 500 miles (805 km) of trailer towing, limit your speed to 50 mph (80 km/h). Perform the maintenance listed in Section 8 of this manual. When towing a trailer, never exceed the GAWR, or GCWR, ratings.
STARTING AND OPERATING • Vehicles with trailers should not be parked on a grade. When parking, apply the parking brake on the tow vehicle. Put the tow vehicle automatic transmission in P for Park. With a manual transmission, shift the transmission into reverse. Always, block or ⬙chock⬙ the trailer wheels. • GCWR must not be exceeded. • Total weight must be distributed between the tow vehicle and the trailer such that the following four ratings are not exceeded: 1. GVWR 2. GTW 3. GAWR 4.
STARTING AND OPERATING Towing Requirements — Trailer Brakes − Do not interconnect the hydraulic brake system or vacuum system of your vehicle with that of the trailer. This could cause inadequate braking and possible personal injury. − An electronically actuated trailer brake controller is required when towing a trailer with electronically actuated brakes. When towing a trailer equipped with a hydraulic surge actuated brake system, an electronic brake controller is not required.
STARTING AND OPERATING 193 Towing Requirements — Trailer Lights & Wiring Whenever you pull a trailer, regardless of the trailer size, stop lights and turn signals on the trailer are required for motoring safety. The Trailer Tow Package may include a 4 and 7 pin wiring harness. Use a factory approved trailer harness and connector. NOTE: Do not cut or splice wiring into the vehicles wiring harness.
STARTING AND OPERATING Towing Tips — Automatic Transmission The “D” range can be selected when towing. However, if frequent shifting occurs while in this range, the “3” range should be selected. NOTE: Using the “3” range while operating the vehicle under heavy operating conditions will improve performance and extend transmission life by reducing excessive shifting and heat build up. This action will also provide better engine braking.
STARTING AND OPERATING Towing Tips — Electronic Speed Control (If Equipped) − Highway Driving Reduce speed. − Don’t use in hilly terrain or with heavy loads. − Air Conditioning Turn off temporarily. − When using the speed control, if you experience speed drops greater than 10 mph (16 km/h), disengage until you can get back to cruising speed. − Use speed control in flat terrain and with light loads to maximize fuel efficiency.
WHAT TO DO IN EMERGENCIES CONTENTS 䡵 Hazard Warning Flasher . . . . . . . . . . . . . . . . . 198 ▫ Traction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 208 䡵 If Your Engine Overheats . . . . . . . . . . . . . . . . 198 䡵 Freeing A Stuck Vehicle . . . . . . . . . . . . . . . . . 209 䡵 Jacking And Tire Changing . . . . . . . . . . . . . . . 200 䡵 Towing A Disabled Vehicle . . . . . . . . . . . . . . . 209 ▫ Preparations For Jacking . . . . . . . . . . . . . . . .
WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER Do not use this emergency warning system when the vehicle is in motion. Use it when your vehicle is disabled and is creating a safety hazard for other motorists. If it is necessary to leave the vehicle to go for service, the flasher system will continue to operate with the ignition key removed and the vehicle locked. NOTE: With extended use, the flasher may wear down your battery.
WHAT TO DO IN EMERGENCIES NOTE: There are steps that you can take to slow down an impending overheat condition. If your air conditioner is on, turn it off. The air conditioning system adds heat to the engine cooling system and turning off the A/C removes this heat. You can also turn the Temperature control to maximum heat, the Mode control to floor, and the fan control to High. This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.
WHAT TO DO IN EMERGENCIES JACKING AND TIRE CHANGING WARNING! • Getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never get any part of your body under a vehicle that is on a jack. Never start or run the engine while the vehicle is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift. • Do not attempt to change a tire on the side of the vehicle close to moving traffic.
WHAT TO DO IN EMERGENCIES 201 1. Block wheel diagonally opposite flat tire. 2. Remove the spare tire, scissors jack and lug wrench from stowage.
WHAT TO DO IN EMERGENCIES 3. Before raising the vehicle, use lug wrench to carefully pry off wheel cover (if equipped with steel wheels) or center cap (if equipped with aluminum wheels). Loosen, but do not remove, the wheel nuts by turning them counterclockwise one turn while the wheel is still on the ground. WARNING! To avoid possible personal injury, handle the wheel covers with care to avoid contact with the metal edges and retention teeth. 4.
WHAT TO DO IN EMERGENCIES 203 6 Jack Engagement Locations
WHAT TO DO IN EMERGENCIES WARNING! WARNING! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. A loose tire or jack thrown forward in a collision or hard stop could endanger the occupants of the vehicle. Always stow the jack parts and the spare tire in the places provided. 6. Remove lug nuts and tire. 7. Mount spare tire. 8. Tighten all lug nuts on mounting studs. 9.
WHAT TO DO IN EMERGENCIES JUMP-STARTING PROCEDURES IF BATTERY IS LOW WARNING! • Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transaxle cannot be started this way. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle. If the vehicle has a discharged battery, booster cables may be used to obtain a start from another vehicle.
WHAT TO DO IN EMERGENCIES WARNING! Do not permit vehicles to touch each other as this could establish a ground connection and person injury could result. 5. Connect the other cable, first to the negative terminal of the booster battery and then to the jump start attachment of the vehicle with the discharged battery. Make sure you have a good contact on the engine. WARNING! Do not connect the cable to the negative post of the discharged battery.
WHAT TO DO IN EMERGENCIES 7. When removing the jumper cables, reverse the above sequence exactly. Be careful of the moving belts and fan. WARNING! Any procedure other than above could result in: 1. Personal injury caused by electrolyte squirting out the battery vent; 2. Personal injury or property damage due to battery explosion; 3. Damage to charging system of booster vehicle or of immobilized vehicle.
WHAT TO DO IN EMERGENCIES DRIVING ON SLIPPERY SURFACES Acceleration Rapid acceleration on snow covered, wet, or other slippery surfaces may cause the front wheels to pull erratically to the right or left. This phenomenon occurs when there is a difference in the surface traction under the front (driving) wheels, particularly with high output engines. WARNING! Rapid acceleration on slippery surfaces is dangerous. Unequal traction can cause sudden pulling of the front wheels.
WHAT TO DO IN EMERGENCIES FREEING A STUCK VEHICLE If your vehicle is equipped with Traction Control, turn the system off before attempting to “rock” the vehicle. If your vehicle becomes stuck in mud, sand or snow, it can often be moved by a rocking motion. Turn your steering wheel right and left to clear the area around the front wheels. Then shift back and forth between Reverse and First gear.
WHAT TO DO IN EMERGENCIES TOWING THIS VEHICLE BEHIND ANOTHER VEHICLE (Flat towing with all four wheels on the ground) Automatic Transaxle Your vehicle may be towed under the following conditions: The gear selector must be in NEUTRAL, the distance to be towed must not exceed 15 miles (25 km), and the towing speed must not exceed 25 mph (40 km/h).
MAINTAINING YOUR VEHICLE CONTENTS 䡵 2.4L Engine . . . . . . . . . . . . . . . . . . . . . . . . . . 213 ▫ Power Steering — Fluid Check . . . . . . . . . . . . 227 䡵 2.7L Engine . . . . . . . . . . . . . . . . . . . . . . . . . . 214 ▫ Suspension Ball Joints . . . . . . . . . . . . . . . . . . 228 䡵 Onboard Diagnostic System — OBD II . . . . . . 215 ▫ Body Mechanism Lubrication . . . . . . . . . . . . . 228 䡵 Emissions Inspection And Maintenance Programs . . . . . . . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE ▫ Appearance Care And Protection From Corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . . 241 䡵 Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 245 ▫ Underhood Fuses (Power Distribution Center) . . . . . . . . . . . . . . 245 ▫ Interior Fuses . . . . . . . . . . . . . . . . . . . . . . . . 246 䡵 Vehicle Storage . . . . . . . . . . . . . . . . . . . . . . . . 248 䡵 Replacement Light Bulbs . . . . . . . . . . . . . . . . 248 䡵 Bulb Replacement . .
MAINTAINING YOUR VEHICLE 213 2.4L ENGINE 7 2.
MAINTAINING YOUR VEHICLE 2.7L ENGINE 2.
MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
MAINTAINING YOUR VEHICLE EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle’s emissions control system. Failure to pass could prevent vehicle registration. For states which have an I/M (Inspection and Maintenance) requirement, this check verifies the following: the MIL (Malfunction Indicator Lamp) is functioning and is not on when the engine is running, and that the OBD (On Board Diagnostic) system is ready for testing.
MAINTAINING YOUR VEHICLE If your OBD system is not ready, you should see your authorized dealer or repair facility. If your vehicle was recently serviced or had a battery failure or replacement, you may need to do nothing more than drive your vehicle as you normally would in order for your OBD system to update. A recheck with the above test routine may then indicate that the system is now ready.
MAINTAINING YOUR VEHICLE WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the proper equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic. MAINTENANCE PROCEDURES The pages that follow contain the required maintenance services determined by the engineers who designed your vehicle.
MAINTAINING YOUR VEHICLE 219 • Day and night temperatures are below 32° F (0° C) • Stop and Go driving • Extensive engine idling. • Driving in dusty conditions • Short trips of less than 10 miles (16.2 km) • More than 50% of your driving is at sustained high speeds during hot weather, above 90° F (32° C) • Trailer towing Engine Oil Dipstick CAUTION! Overfilling or underfilling will cause aeration or loss of oil pressure. This could damage your engine.
MAINTAINING YOUR VEHICLE If none of these apply to you, then change your engine oil at every interval shown on schedule ⬙A⬙ of the ⬙Maintenance Schedules⬙ section of this manual. NOTE: Under no circumstances should oil change intervals exceed 6,000 miles (10 000 km) or 6 months whichever comes first.
MAINTAINING YOUR VEHICLE Engine Oil Viscosity (SAE Grade) 221 Synthetic Engine Oils You may use synthetic engine oils provided that the recommended oil quality requirements are met and the recommended maintenance intervals for oil and filter changes are followed. Materials Added To Engine Oils The manufacturer strongly recommends against the addition of any additives (other than leak detection dyes) to engine oil.
MAINTAINING YOUR VEHICLE Engine Oil Filter Selection All manufacturer’s engines have a full-flow type disposable oil filter. Use a filter of this type for replacement. The quality of replacement filters varies considerably. Only high quality filters should be used to assure most efficient service. Mopar Engine Oil Filters are high quality oil filters and are recommended. Spark Plugs Spark plugs must fire properly to assure engine performance and emission control.
MAINTAINING YOUR VEHICLE WARNING! The air cleaner can provide a measure of protection in the case of engine backfire. Do not remove the air cleaner unless such removal is necessary for repair or maintenance. Make sure that no one is near the engine compartment before starting the vehicle with the air cleaner removed. Failure to do so can result in serious personal injury. Engine Fuel Filter A plugged fuel filter can cause hard starting or limit the speed at which a vehicle can be driven.
MAINTAINING YOUR VEHICLE WARNING! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your exhaust system. Do not park or operate your vehicle in areas where your exhaust system can contact anything that can burn. In unusual situations involving grossly malfunctioning engine operation, a scorching odor may suggest severe and abnormal catalyst overheating.
MAINTAINING YOUR VEHICLE the tire and wheel. Remote battery terminals are located in the engine compartment for jump starting. Battery Location To access the battery, turn the steering wheel fully to the right and remove the inner fender shield. 225 WARNING! Battery posts, terminals and related accessories contain lead and lead compounds. Wash hands after handling. Battery fluid is a corrosive acid solution and can burn or even blind you.
MAINTAINING YOUR VEHICLE CAUTION! It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked positive (+) and negative (-) and identified on the battery case. Cable clamps should be tight on the terminal posts and free of corrosion. Apply grease to posts and clamps after tightening.
MAINTAINING YOUR VEHICLE Refrigerant Recovery and Recycling R-134a Air Conditioning Refrigerant is a hydrofluorocarbon (HFC) that is endorsed by the Environmental Protection Agency and is an ozone-saving product. However, the manufacturer recommends that air conditioning service be performed by dealers or other service facilities using recovery and recycling equipment.
MAINTAINING YOUR VEHICLE Fluid level should be maintained at the proper level indicated on the side of the reservoir. If necessary, add fluid to restore the proper indicated level. With a clean cloth, wipe any spilled fluid from all surfaces. Refer to Fluids, Lubricants, and Genuine Parts for correct fluid type. Suspension Ball Joints There are two upper front and rear suspension ball joints. Inspect these ball joints whenever under vehicle service is done.
MAINTAINING YOUR VEHICLE If you use a lubricant that cannot be dispensed directly into the lock cylinder, apply a small amount of the lubricant to the key. Insert the key into the lock cylinder, then proceed as described above, to distribute the lubricant within the lock cylinder. Pay attention to trunk hinges, especially during cold weather, to ensure ease of trunk operation.
MAINTAINING YOUR VEHICLE Windshield Wiper Blade Replacement • Lift the wiper arm away from the glass. • Push the release tab and slide the wiper blade assembly away from the wiper arm. Gently place the wiper arm on the windshield. • Install the new blade assembly onto the wiper arm tip until it locks in place. Windshield Washers The fluid reservoir in the engine compartment should be checked for fluid level at regular intervals.
MAINTAINING YOUR VEHICLE Exhaust System The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. If you notice a change in the sound of the exhaust system; or if exhaust fumes can be detected inside the vehicle; or when the underside or rear of the vehicle is damaged; have a competent mechanic inspect the complete exhaust system and adjacent body areas for broken, damaged, deteriorated, or mispositioned parts.
MAINTAINING YOUR VEHICLE Coolant Checks Check engine coolant (antifreeze) protection every 12 months (before the onset of freezing weather, where applicable). If coolant is dirty or rusty in appearance, the system should be drained, flushed and refilled with fresh coolant. Check the front of the radiator for any accumulation of bugs, leaves, etc. If dirty, clean by gently spraying water from a garden hose vertically down the face of the condenser.
MAINTAINING YOUR VEHICLE Adding Coolant Your vehicle has been built with an improved engine coolant that allows extended maintenance intervals. This coolant can be used up to 5 Years or 100,000 miles before replacement. To prevent reducing this extended maintenance period, it is important that you use the same coolant throughout the life of your vehicle. Please review these recommendations for using Hybrid Organic Additive Technology (HOAT) coolant.
MAINTAINING YOUR VEHICLE WARNING! • The warning words “DO NOT OPEN HOT” on the cooling system pressure cap are a safety precaution. Never add coolant when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system. To prevent scalding or injury, do not remove the pressure cap while the system is hot or under pressure. • Do not use a pressure cap other than the one specified for your vehicle.
MAINTAINING YOUR VEHICLE Points To Remember NOTE: When the vehicle is stopped after a few miles (a few kilometers) of operation, you may observe vapor coming from the front of the engine compartment. This is normally a result of moisture from rain, snow, or high humidity accumulating on the radiator and being vaporized when the thermostat opens, allowing hot coolant to enter the radiator.
MAINTAINING YOUR VEHICLE Pay particular attention to those hoses nearest to high heat sources such as the exhaust manifold. Inspect hose routing to be sure hoses do not touch any heat source or moving component that may cause heat damage or mechanical wear. Insure nylon tubing in these areas has not melted or collapsed. Inspect all hose connections such as clamps and couplings to make sure they are secure and no leaks are present.
MAINTAINING YOUR VEHICLE Insure nylon tubing in these areas has not melted or collapsed. NOTE: Often, fluids such as oil, power steering fluid, and brake fluid are used during assembly plant operations to ease the assembly of hoses to couplings. Therefore, oil wetness at the hose-coupling area is not necessarily an indication of leakage. Actual dripping of hot fluid when systems are under pressure (during vehicle operation) should be noted before hose is replaced based on leakage.
MAINTAINING YOUR VEHICLE Use only manufacturer’s recommended brake fluid, refer to Fluids, Lubricants and Genuine Parts for correct fluid type. WARNING! Use of a brake fluid that has a lower initial boiling point than MOPAR DOT 3 Brake Fluid or that is unidentified as to DOT FMVSS specification may result in sudden brake failure during hard or prolonged braking. You could have an accident.
MAINTAINING YOUR VEHICLE 239 Selection of Lubricant It is important that the proper lubricant is used in the transmission to assure optimum transmission performance. Use only manufacturers recommended transmission fluid, refer to Fluids, Lubricants and Genuine Parts for correct fluid type. It is important that the transmission fluid be maintained at the prescribed level using the recommended fluid.
MAINTAINING YOUR VEHICLE • If the fluid is hot (180°F / 82°C), the reading should be in the cross hatched area marked ”HOT” (between the upper two holes in the dipstick). • Police, taxi, limousine, commercial type operation, or trailer towing where the vehicle is driven regularly for more than 45 minutes of continuous operation. • If the fluid level shows low, add sufficient transmission fluid to bring to the proper level. NOTE: Refer to Section 8 of this manual for maintenance schedules.
MAINTAINING YOUR VEHICLE 241 the vehicle. Fluid changes are not necessary unless the lubricant has become contaminated with water. If contaminated with water, the fluid should be changed immediately. What Causes Corrosion? Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle. Appearance Care And Protection From Corrosion • Road salt, dirt and moisture accumulation.
MAINTAINING YOUR VEHICLE • Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish. CAUTION! Do not use abrasive or strong cleaning materials such as steel wool or scouring powder, which will scratch metal and painted surfaces. Special Care • If you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month.
MAINTAINING YOUR VEHICLE Never use cleaners that contain acid, oven cleaners or any abrasive metal cleaner as they will cause permanent staining and/or corrosion. • If you carry special cargo such as chemicals, fertilizers, deicer salt, etc., be sure that such materials are well packaged and sealed. • If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel. Interior Care Use Mopar Fabric Cleaner or equivalent to clean fabric upholstery and carpeting.
MAINTAINING YOUR VEHICLE Leather is best preserved by regular cleaning with a damp soft cloth. Small particles of dirt can act as an abrasive and damage the leather surface and should be removed immediately with a damp cloth. Stubborn soils can be removed easily with a soft cloth and Mopar Total Clean or equivalent. Care should be taken to avoid soaking the leather with any liquid. Glass Surfaces All glass surfaces should be cleaned on a regular basis with any commercial household-type glass cleaner.
MAINTAINING YOUR VEHICLE Cleaning Plastic Instrument Cluster Lenses The lenses in front of the instruments in this vehicle are molded in clear plastic. When cleaning the lenses, care must be taken to avoid scratching the plastic. 245 FUSES Underhood Fuses (Power Distribution Center) • Clean with a wet soft rag. A mild soap solution may be used, but do not use high alcohol content or abrasive cleaners. If soap is used, wipe clean with a clean damp rag. • Dry with a soft tissue.
MAINTAINING YOUR VEHICLE A Power Distribution Center is located in the engine compartment; near the air cleaner. This information applies to vehicles built without the fuse and relay numbering embossed on the Power Distribution Center Top Cover. Interior Fuses The identity of each fuse is indicated on the backside of the cover.
MAINTAINING YOUR VEHICLE Cavity Fuse 6 10 Amp Red 7 20 Amp Yellow 8 20 Amp Yellow 9 15 Amp Blue 10 20 Amp Yellow 11 10 Amp Red 12 13 14 10 Amp Red 20 Amp Yellow 10 Amp Red Circuit Heated Rear Window Indicator Instrument cluster illumination, Park and tail Lights Power Receptacle, Horns, Ignition, Fuel, Start Power Door Lock Motors (Body Control Module) Daytime Running Light Module (Canada) Instrument Cluster, Transmission Control, Park/Neutral Switch, Body Control Module Left Low beam Headlight Right Low
MAINTAINING YOUR VEHICLE VEHICLE STORAGE If you are leaving your vehicle dormant for more than 21 days you may want to take steps to protect your battery. You may: • Disconnect the negative cable from the battery. • Anytime you store your vehicle, or keep it out of service (i.e. vacation) for two weeks or more, run the air conditioning system at idle for about five minutes in the fresh air and high blower setting.
MAINTAINING YOUR VEHICLE BULB REPLACEMENT Headlight Bulb Replacement 249 2. Remove the push-in fasteners by prying under the head of the fasteners with a flat bladed tool. 1. Open the hood and remove the two headlight mounting screws.
MAINTAINING YOUR VEHICLE 3. Gently pry the headlight assembly away from the fender as shown in the picture. This will free the ball stud from its retainer in the fender. Pull the headlight assembly away from the vehicle. 5. Pull the bulb out of the socket and replace the bulb. CAUTION! 4. Turn the retaining ring counterclockwise and remove the bulb and socket assembly. Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. 6.
MAINTAINING YOUR VEHICLE 7. Reinsert the bulb and socket assembly and turn the retaining ring clockwise to secure the bulb. 251 2. Turn the bulb socket counterclockwise and remove the bulb and socket assembly. 8. Reinstall the headlight assembly. Park, Turn Signal, Sidemarker Bulb Replacement 1. Open the hood and remove the two headlight assembly mounting screws. Pull the headlight assembly away from the vehicle. 7 3.
MAINTAINING YOUR VEHICLE Fog Light Bulb Replacement 1. Remove the screws securing the light assembly to the front fascia. 2. Pull the light assembly away from the vehicle to expose the bulb and socket assembly. 3. Disconnect the wiring connector from the bulb and socket assembly. 4. Turn the bulb and socket assembly counterclockwise to remove it from the housing. 5. Install the new bulb and socket assembly, reattach the wiring connector, and reinstall the fog light assembly.
MAINTAINING YOUR VEHICLE 253 Center Stoplight Bulb Replacement Rear Light Bulb Replacement 1. Open the trunk. Turn the bulb socket counterclockwise to remove it from the housing. 1. Open the trunk and pull the trunk liner away to expose the wiring connector and light housing plastic retainers. 7 2. Pull the bulb out of the socket, replace the bulb and reinstall the bulb and socket assembly. 2. Disconnect the wiring connector and remove the plastic retainers. Remove the light housing from the vehicle.
MAINTAINING YOUR VEHICLE 4. Reinstall the light housing and reconnect the wiring connector. Push the trunk liner back into place. License Plate Bulb Replacement 1. Locate both small slots on the outboard side of the license lamp. Using a small screwdriver, remove the entire housing. 2. Turn the bulb socket counterclockwise to remove it from the housing. Pull the bulb out of the socket. Replace the bulb and snap it back into place on the housing of the chrome appliqué.
MAINTAINING YOUR VEHICLE 255 FLUIDS AND CAPACITIES Fuel (approximate) 2.4 and 2.7 Liter Engines (87 Octane) Engine Oil-With Filter 2.4 and 2.7 Liter Engines (Refer to the engine oil fill cap for the correct SAE grade) Cooling System * 2.4 Liter Engines* (Mopar威 Antifreeze/Coolant 5 Year/100,000 Mile Formula) or equivalent. 2.7 Liter Engines (Mopar威 Antifreeze/Coolant 5 Year/100,000 Mile Formula) or equivalent. * Includes 1 qt. for coolant tank. U.S. Metric 16 Gallons 61 Liters 5 qts. 4.
MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant Engine Oil Spark Plugs Oil Filter (2.4L Engine) Oil Filter (2.7L Engine) Fuel Selection Fluid, Lubricant, or Genuine Part Mopar威 Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) or equivalent. Use API Certified engine oil. SAE 5W-20 and SAE 5W-30 are recommended.
MAINTAINING YOUR VEHICLE 257 Chassis Component Automatic Transaxle Brake Master Cylinder Power Steering Reservoir Steering Gear & Linkage, Ball Joints, Prop Shafts & Yokes, Wheel Bearings Fluid, Lubricant, or Genuine Part Mopar威 ATF+4 Automatic Transmission Fluid. Mopar威 DOT 3, SAE J1703 should be used. If DOT 3, SAE J1703 brake fluid is not available, then DOT 4 is acceptable. Use only recommended brake fluids. Mopar威 Power Steering Fluid + 4, Mopar威 ATF+4 Automatic Transmission Fluid.
MAINTENANCE SCHEDULES CONTENTS M A I N T E N A N C E 䡵 Emission Control System Maintenance . . . . . . 260 ▫ Schedule “B” . . . . . . . . . . . . . . . . . . . . . . . . 263 䡵 Maintenance Schedules . . . . . . . . . . . . . . . . . . 260 ▫ Schedule “A” . . . . . . . . . . . . . . . . . . . . . . . .
M A I N T E N A N C E 260 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
MAINTENANCE SCHEDULES 261 M A • Taxi, police, or delivery service (commercial service).〫 NOTE: Most vehicles are operated under the conditions I N listed for Schedule ⬙B⬙. T • Off-road or desert operation. Second is Schedule “A”. It is for vehicles that are not N operated under any of the conditions listed under Sched- A N ule ⬙B⬙. • If equipped for and operating with E-85 (ethanol) fuel.
M 262 MAINTENANCE SCHEDULES A I At Each Stop for Fuel N T • Check the engine oil level about 5 minutes after a fully E warmed engine is shut off. Checking the oil level while N A the vehicle is on level ground will improve the accuN racy of the oil level reading. Add oil only when the C level is at or below the ADD or MIN mark. E S C H E D U L E S 8 • Check the windshield washer solvent and add if required. Once a Month • Check tire pressure and look for unusual wear or damage.
SCHEDULE “B” 263 M A SCHEDULE “B” Follow schedule “B” if you usually operate your vehicle under one or more of the following conditions. Change the automatic transmission fluid and filter every 60,000 miles (96 000 km) if the vehicle is usually operated under one or more of the conditions marked with an 〫. • Taxi, police or delivery service (commercial ser- I N vices).〫 T • Day or night temperatures are below 32° F (0° C).
M 264 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter, if not A replaced at 3 months. N C Inspect the air cleaner filter and replace if E necessary.* S C H E D U L E S 8 Inspect the front and rear brake pads, linings, rotors, rear drums and shoes. Rotate the tires.
SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Inspect the air cleaner filter and replace if required.* Replace the air cleaner filter. Inspect and check tension for power steering belt (2.4 Liter Engine). Adjust or replace if required. Inspect the front and rear brake pads, linings, rotors, rear drums and shoes. Check and replace, if necessary, the PCV valve. * Replace the spark plugs on 2.4 liter engine. Rotate the tires.
M 266 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter, if not A replaced at 3 months. N C Inspect the air cleaner filter and replace if E necessary.* S C H E D U L E S 8 Inspect the front and rear brake pads, linings, rotors, rear drums and shoes. Rotate the tires.
SCHEDULE “B” Miles 57,000 (Kilometers) (95 000) Change engine oil and engine oil filter, if not X replaced at 3 months. Inspect the air cleaner filter and replace if necesX sary.* Replace the air cleaner filter. Inspect and check tension for power steering belt (2.4 Liter Engine). Adjust or replace if required. Inspect the front and rear brake pads, linings, rotors, rear drums and shoes. Replace the ignition cables on 2.4 liter engine. Replace the accessory drive belts on the 2.7 liter engine.
M 268 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter, if not A replaced at 3 months. N C Inspect the air cleaner filter and replace if E necessary.* S C H E D U L E S 8 Replace the air cleaner filter. Inspect and check tension for power steering belt (2.4 Liter Engine). Adjust or replace if required. Replace the engine timing belt on 2.4 liter engine. Inspect the front and rear brake pads, linings, rotors, rear drums and shoes. Replace the spark plugs on 2.
SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Inspect the air cleaner filter and replace if necessary.* Inspect the front and rear brake pads, linings, rotors, rear drums and shoes. Replace the spark plugs on the 2.7 liter engine. Check and re-tension accessory drive belts on 2.7 liter engine. Replace the accessory drive belts on 2.4 liter engine. Rotate the tires. Flush and replace the engine coolant, if not replaced at 60 months.
M 270 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter, if not reA placed at 3 months. N C Inspect the air cleaner filter and replace if necesE sary.* S C H E D U L E S 8 Replace the air cleaner filter. Replace the spark plugs on the 2.4 liter engine. Replace the ignition cables on the 2.4 liter engine. Inspect the front and rear brake pads, linings, rotors, rear drums and shoes. Inspect and check tension for power steering belt (2.4 Liter Engine).
SCHEDULE “B” * This maintenance is recommended by the manufacture to the owner but is not required to maintain the emissions warranty. ‡ This maintenance is not required if previously replaced. 271 M Inspection and service should also be performed anytime a malfunction is observed or suspected. Retain all receipts.
M 272 SCHEDULE “A” A I SCHEDULE “A” N T Miles E N (Kilometers) A [Months] N C Change engine oil and engine oil filter. E Inspect the air cleaner filter and replace if S C H E D U L E S 8 necessary.* Replace the air cleaner filter. Replace the spark plugs on 2.4 liter engine. Inspect the front and rear brake pads, linings, rotors, rear drums and shoes. Rotate the tires.
SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Inspect the air cleaner filter and replace if required.* Replace the air cleaner filter. Inspect and check tension for power steering belt (2.4 Liter Engine). Adjust or replace if required. Inspect the front and rear brake pads, linings, rotors, rear drums and shoes. Replace the spark plugs on 2.4 liter engine. Flush and replace the engine coolant at 60 months, if not done at 100,000 miles.
M 274 SCHEDULE “A” A I N Miles T (Kilometers) E N [Months] A Change engine oil and engine oil filter. N C Inspect the air cleaner filter and replace E if required.* S C H E D U L E S 8 Replace the air cleaner filter. Inspect the front and rear brake pads, linings, rotors, rear drums and shoes. Replace the spark plugs on 2.4 liter engine. Replace the spark plugs on 2.7 liter engine. Check and replace, if necessary, the PCV valve. *‡ Check and re-tension alternator drive belts on 2.7 liter engine.
SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Inspect the air cleaner filter and replace if required.* Replace the air cleaner filter. Inspect the front and rear brake pads, linings, rotors, rear drums and shoes. Replace the spark plugs on 2.4 liter engine. Check and replace, if necessary, the PCV valve. *‡ Replace the engine timing belt on 2.4 liter engine. Inspect and check tension for power steering belt (2.4 Liter Engine). Adjust or replace if required.
M A I N T E N A N C E S C H E D U L E S 8 276 SCHEDULE “A” Inspection and service should also be performed anytime a malfunction is observed or suspected. Retain all receipts. WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS 䡵 Suggestions For Obtaining Service For Your Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 278 ▫ Prepare For The Appointment . . . . . . . . . . . . 278 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . . . 278 䡵 Reporting Safety Defects . . . . . . . . . . . . . . . . . 281 ▫ In Canada . . . . . . . . . . . . . . . . . . . . . . . . . . 281 䡵 Publication Order Forms . . . . . . . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty, discuss additional charges with the service manager. Keep a maintenance log of your vehicle’s service history. This can often provide a clue to the current problem.
IF YOU NEED CONSUMER ASSISTANCE • If for some reason you are still not satisfied, talk to the general manager or owner of the dealership. They want to know if you need assistance. • If your dealership is unable to resolve the concern, you may contact the Manufacturer’s Customer Center.
IF YOU NEED CONSUMER ASSISTANCE Service Contract You may have purchased a service contract for your vehicle to help protect you from the high cost of unexpected repairs after your manufacturer’s new vehicle limited warranty expires. The manufacturer stands behind only the manufacturer’s Service Contracts. If you purchased a manufacturer’s Service Contract, you will receive Plan Provisions and an Owner Identification Card in the mail within three weeks of your vehicle delivery date.
IF YOU NEED CONSUMER ASSISTANCE REPORTING SAFETY DEFECTS In the 50 United States and Washington D.C.: If you believe that your vehicle has a defect which could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying the manufacturer. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
IF YOU NEED CONSUMER ASSISTANCE • Service Manuals. These comprehensive service manuals provide the information that students and professional technicians need in diagnosing/troubleshooting, problem solving, maintaining, servicing and repairing DaimlerChrysler Corporation vehicles. A complete working knowledge of the vehicle, system and/or components is written in straightforward language with illustrations, diagrams and charts. • Diagnostic Procedure Manuals.
IF YOU NEED CONSUMER ASSISTANCE 283 DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES The following describes the tire grading categories established by the National highway Traffic Safety Administration. The specific grade rating assigned by the tire’s manufacturer in each category is shown on the sidewall of the tires on your car. Traction Grades The traction grades, from highest to lowest, are AA, A, B, and C.
IF YOU NEED CONSUMER ASSISTANCE Temperature Grades The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
INDEX 10
INDEX About Your Brakes . . . . . . . . . . . . . . . . . . . . . . 155 ABS (Anti-Lock Brake System) . . . . . . . . . . . . . 155 Adding Engine Coolant (Antifreeze) . . . . . . . . . 233 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . 183 Adding Washer Fluid . . . . . . . . . . . . . . . . . . . . 230 Additives, Fuel . . . . . . . . . . . . . . . . . . . . . . . . 179 Aiming Headlights . . . . . . . . . . . . . . . . . . . . . . 254 Air Cleaner, Engine (Engine Air Cleaner Filter) . .
INDEX Selection Of Lubricant . . . . . . . . . . . . . . . 239,257 Shifting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151 Special Additives . . . . . . . . . . . . . . . . . . . . . 240 Autostick . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176 Auxiliary Power Outlet . . . . . . . . . . . . . . . . . . . 80 Ball Joints . . . . . . . . . . . . . . . . . . . . . . . . . . . . 228 Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 224 Emergency Starting . . . . .
INDEX Chains, Tire . . . . . . . . . . . . . . . . . . . . . . . . . . . 175 Changing A Flat Tire . . . . . . . . . . . . . . . . . . . . 200 Charging System Light . . . . . . . . . . . . . . . . . . . 89 Chart, Tire Sizing . . . . . . . . . . . . . . . . . . . . . . . 160 Check Engine Light (Malfunction Indicator Light) . . . . . . . . . . . . . . 216 Checking Your Vehicle For Safety . . . . . . . . . . . . 46 Child Restraint . . . . . . . . . . . . . . . . . . .
INDEX Cruise Light . . . . . . . . . . . . . . . . . . . . . . . . . . . 88 Customer Assistance . . . . . . . . . . . . . . . . . . . . 278 Daytime Brightness, Interior Lights . . . . . . . . . . 63 Daytime Running Lights . . . . . . . . . . . . . . . . . . 66 Dealer Service . . . . . . . . . . . . . . . . . . . . . . . . . 217 Defroster, Rear Window . . . . . . . . . . . . . . . . . . 138 Defroster, Windshield . . . . . . . . . . . . . . . 47,132,138 Diagnostic System, Onboard . . . . . . . . . . . . . .
INDEX Oil . . . . . . . . . . . . . . . . . . . . . . . . . . 218,255,256 Oil Change Interval . . . . . . . . . . . . . . . . . . . 219 Oil Selection . . . . . . . . . . . . . . . . . . . . . . 220,255 Oil Synthetic . . . . . . . . . . . . . . . . . . . . . . . . . 221 Overheating . . . . . . . . . . . . . . . . . . . . . . . . . 198 Timing Belt . . . . . . . . . . . . . . . . . . . . . . . . . . 224 Engine Oil Viscosity . . . . . . . . . . . . . . . . . . . . . 255 Entry System, Illuminated . . . . .
INDEX Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178 Adding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183 Additives . . . . . . . . . . . . . . . . . . . . . . . . . . . 179 Clean Air . . . . . . . . . . . . . . . . . . . . . . . . . . . 178 Filler Cap (Gas Cap) . . . . . . . . . . . . . . . . . . . 183 Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 223 Gasoline . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178 Gauge . . . . . . . .
INDEX Heated Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 Heater . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129,135 Heater, Engine Block . . . . . . . . . . . . . . . . . . . . 148 Hitches Trailer Towing . . . . . . . . . . . . . . . . . . . . . . . 187 HomeLink威 (Garage Door Opener) Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 Hood Latch Maintenance . . . . . . . . . . . . . . . . . 228 Hood Prop . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Latches Hood . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61,228 Lead Free Gasoline . . . . . . . . . . . . . . . . . . . . . . 178 Leaks, Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Life of Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . 173 Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47,62 Airbag . . . . . . . . . . . . . . . . . . . . . . . . 36,38,47,89 Anti-Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Locks Central . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Child Protection . . . . . . . . . . . . . . . . . . . . . . . 17 Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . 228 Cylinder Maintenance . . . . . . . . . . . . . . . . . . 228 Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Ignition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Lower Anchors and Tether for CHildren (LATCH) . . . . . . . . . . . . . . . . . . . .
INDEX Filter Disposal . . . . . . . . . . . . . . . . . . . . . . . 221 Identification Logo . . . . . . . . . . . . . . . . . . . . 220 Materials Added to . . . . . . . . . . . . . . . . . . . . 221 Pressure Gauge . . . . . . . . . . . . . . . . . . . . . . . 92 Quality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220 Recommendation . . . . . . . . . . . . . . . . . . 220,255 Synthetic . . . . . . . . . . . . . . . . . . . . . . . . . . . 221 Viscosity . . . . . . . . . . . . . . . . . . . . .
INDEX Radio, Satellite . . . . . . . . . . . . . . . . . . . . . . . . . 122 Radio (Sound Systems) . . . . . . . . . . . . . . 99,108,113 Rear Seat, Folding . . . . . . . . . . . . . . . . . . . . . . . 60 Rear Window Defroster . . . . . . . . . . . . . . . . . . 138 Rearview Mirrors . . . . . . . . . . . . . . . . . . . . . . . . 54 Reformulated Gasoline . . . . . . . . . . . . . . . . . . . 178 Refrigerant . . . . . . . . . . . . . . . . . . . . . . . . . . . . 227 Reminder, Lights On . . . . . . .
INDEX Rear Folding . . . . . . . . . . . . . . . . . . . . . . . . . 60 Reclining . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 Security Alarm (Theft Alarm) . . . . . . . . . . . . . . . 21 Selection of Coolant (Antifreeze) . . . . . . . . . 232,256 Sentry Key (Immobilizer) . . . . . . . . . . . . . . . . . 9,11 Service Assistance . . . . . . . . . . . . . . . . . . . . . . 278 Service Contract . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Tire and Loading Information Placard . . . . . . . 163 Tire Identification Number (TIN) . . . . . . . . . . . 162 Tire Markings . . . . . . . . . . . . . . . . . . . . . . . . . 158 Tire Safety Information . . . . . . . . . . . . . . . . . . . 158 Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . 47,167,283 Aging (Life of Tires) . . . . . . . . . . . . . . . . . . . 173 Air Pressure . . . . . . . . . . . . . . . . . . . . . . . . . 167 Alignment . . . . . . . . . . . . . . . . . . . .
INDEX Overdrive . . . . . . . . . . . . . . . . . . . . . . . . . . . 152 Selection of Lubricant . . . . . . . . . . . . . . . . . . 239 Transmission Range Indicator . . . . . . . . . . . . . . . . . . . . . . . 91 Transmission . . . . . . . . . . . . . . . . . . . . See Transaxle Transmitter Battery Service (Remote Keyless Entry) . . . . . . . . . . . . . . . . . . . 21 Transmitter, Garage Door Opener (HomeLink威) . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Windshield Washers . . . . . . . . . . . . . . . . . . . 67,230 Windshield Wiper Blades . . . . . . . . . . . . . . . . . 230 Windshield Wipers . . . . . . . . . . . . . . . . . 65,67,229 Wiper Blade Replacement . . . . . . . . . . . . . . . . . 230 Wipers, Intermittent . . . . . . . . . . . . . . . . . . . . . . 68 Wood Trim Cleaning . . . . . . . . . . . .
