Owner's Manual

ManualsBrandsChrysler ManualsAutomobileChrysler 2006 Chrysler Pacifica

TABLE OF CONTENTS

SECTION PAGE

INTRODUCTION

.............................................................3

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

..............................9

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

..............................75

UNDERSTANDING YOUR INSTRUMENT PANEL

...................................161

STARTING AND OPERATING

.................................................255

WHAT TO DO IN EMERGENCIES

..............................................317

MAINTAINING YOUR VEHICLE

...............................................335

MAINTENANCE SCHEDULES

..................................................389

IF YOU NEED CONSUMER ASSISTANCE

.........................................413

INDEX

....................................................................421

Summary of content (440 pages)

PAGE 1
SECTION TABLE OF CONTENTS PAGE 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 3 4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 2
PAGE 3
INTRODUCTION CONTENTS 䡵 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 Vehicle Identification Number . . . . . . . . . . . . . . . 6 䡵 How To Use This Manual . . . . . . . . . . . . . . . . . . 4 䡵 Vehicle Modifications / Alterations . . . . . . . . . . . 7 䡵 Warnings And Cautions . . . . . . . . . . . . . . . . . . .
PAGE 4
INTRODUCTION INTRODUCTION This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a Warranty Information Booklet and various customer oriented documents. You are urged to read these publications carefully. Following the instructions and recommendations in this manual will help assure safe and enjoyable operation of your vehicle.
PAGE 5
INTRODUCTION 5 1
PAGE 6
INTRODUCTION WARNINGS AND CAUTIONS This manual contains WARNINGS against operating procedures which could result in an accident or bodily injury. It also contains CAUTIONS against procedures which could result in damage to your vehicle. If you do not read this entire manual you may miss important information. Observe all Warnings and Cautions.
PAGE 7
INTRODUCTION 7 VEHICLE MODIFICATIONS / ALTERATIONS 1 WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
PAGE 8
PAGE 9
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS 䡵 A Word About Your Keys . . . . . . . . . . . . . . . . . .11 ▫ Manual Door Locks . . . . . . . . . . . . . . . . . . . . .16 ▫ Ignition Key Removal . . . . . . . . . . . . . . . . . . .11 ▫ Power Door Locks . . . . . . . . . . . . . . . . . . . . .17 ▫ Key-In-Ignition Reminder . . . . . . . . . . . . . . . .12 ▫ Child Protection Door Lock . . . . . . . . . . . . . . .19 䡵 Sentry Key . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 10
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ To Turn Off “Flash Lights On Lock/Unlock” . . .23 ▫ General Information . . . . . . . . . . . . . . . . . . . .24 ▫ Transmitter Battery Service . . . . . . . . . . . . . . .24 䡵 Vehicle Theft Alarm . . . . . . . . . . . . . . . . . . . . . .26 䡵 Liftgate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 ▫ Power Liftgate — If Equipped . . . . . . . . . . . . .29 䡵 Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 11
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS You can insert the double sided keys into the locks with either side up. 11 be used to order duplicate keys from your dealer. Ask your dealer for these numbers and keep them in a safe place. Ignition Key Removal The shift lever must be in PARK. Turn the key to the LOCK position, then remove the key. Vehicle Key The dealer that sold you your new vehicle has the key code numbers for your vehicle locks.
PAGE 12
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: The power window switches, radio, power sunroof, and power outlets will remain active for up to 45 seconds after the ignition switch has been turned off. Opening either front door will cancel this feature. CAUTION! An unlocked car is an invitation to thieves. Always remove key from the ignition and lock all doors when leaving the vehicle unattended. WARNING! Leaving children in a vehicle unattended is dangerous for a number of reasons.
PAGE 13
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE chip (transponder) embedded into them. Only keys that have been programmed to the vehicle can be used to start and operate the vehicle. The Sentry Key Immobilizer System does not need to be armed or activated. Operation of the system is automatic regardless of whether or not the vehicle is locked or unlocked.
PAGE 14
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE All of the keys provided with your new vehicle have been programmed to the vehicle electronics. Replacement Keys NOTE: Only keys that have been programmed to the vehicle electronics can be used to start the vehicle. Once a Sentry Key has been programmed to a vehicle, it can not be programmed to any other vehicle. At the time of purchase, the original owner is provided with a four digit PIN number. This number is required for dealer replacement of keys.
PAGE 15
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 4. Insert a blank Sentry Key into the ignition switch and turn the ignition switch ON within 60 seconds. After 10 seconds a single chime will sound. The Theft Alarm Light will stop flashing, turn on for 3 seconds; then turn off. General Information The Sentry Key system complies with FCC rules part 15 and with RSS-210 of Industry Canada. Operation is subject to the following conditions: The new Sentry Key has been programmed.
PAGE 16
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE DOOR LOCKS Manual Door Locks Lock the doors by pushing up on the lock knob on each door trim panel. If the lock knob is up when you shut the door, the door will lock. Therefore, make sure the keys are not inside the vehicle before closing the door. WARNING! • For personal security and safety in the event of an accident, lock the vehicle doors as you drive as well as when you park and leave the vehicle.
PAGE 17
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Power Door Locks A power door lock switch is on each front door trim panel. Use this switch to lock or unlock the doors. 17 locks will not operate. This prevents you from accidentally locking your keys in the vehicle. Removing the key or closing the door will allow the locks to operate. A chime will sound if the key is in the ignition and a door is open, as a reminder to remove the key.
PAGE 18
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The Automatic Door Locks can be enabled or disabled by performing the following procedure: 1. Close all doors and place the key in the ignition switch. Auto Unlock On Exit— If Equipped The doors will unlock automatically on vehicles with power door locks if: 1. The Auto Unlock feature is enabled, 2. Cycle the ignition switch ON/OFF four times ending in the OFF position. (do not start the engine) 2.
PAGE 19
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Cycle the ignition switch ON/OFF four times ending in the OFF position. (do not start the engine) 3. Within 10 seconds of the final cycle, press the interior driver’s door lock switch to the UNLOCK position. 19 Child Protection Door Lock To provide a safer environment for small children riding in the rear seats, the rear doors are equipped with a child protection door lock system. 4.
PAGE 20
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To activate the system, open the rear door and move the child lock control, located near the door’s rear latch, to the ON position. When the child lock system is engaged the door can be opened only by using the outside door handle even though the inside door lock is in the unlocked position.
PAGE 21
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 To unlock the doors and liftgate: Press and release the UNLOCK button on the transmitter once to unlock the driver’s door, or twice to unlock all doors and liftgate. The illuminated entry system also turns on. NOTE: If desired, the “Remote Unlock Driver’s Door 1st” feature can be turned on and off by referring to the Customer Programmable Features of the “Electronic Vehicle Information Center (EVIC)” section or by following these steps. 1.
PAGE 22
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To lock the doors and liftgate: Press and release the LOCK button on the transmitter to lock all doors and liftgate. The horn will chirp once to acknowledge the signal. If desired, the “Sound Horn On Lock” feature can be turned on and off by referring to the Customer Programmable Features of the “Electronic Vehicle Information Center (EVIC)” section or by following these steps. 1. Press the LOCK button for 4 to 10 seconds. 2.
PAGE 23
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Program Transmitters: Refer to SENTRY KEY “Customer Key Programming.” If you do not have a programmed transmitter, contact your dealer for details. To Open/Close Power Liftgate — If Equipped Press the LIFTGATE button twice within five seconds to open/close the power liftgate. The liftgate will beep for 2 seconds and then open/close. If the button is pushed while the liftgate is being power closed, the liftgate will reverse to the full open position.
PAGE 24
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The “Flash Lights On Lock/Unlock” feature can be reactivated by repeating this procedure. The table below explains the Lamp Flash options. Function Lock Unlock 1st Press Unlock All Doors Liftgate • This device must accept any interference received, including interference that may cause undesired operation.
PAGE 25
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 1. With the transmitter buttons facing down, use a small screwdriver or similar flat object to pry the two halves of the transmitter apart. Make sure not to damage the rubber gasket during removal. 25 2. Remove and replace the battery. Avoid touching the new battery with your fingers. Skin oils may cause battery deterioration. If you touch a battery, clean it with rubbing alcohol. 3. To reassemble the transmitter case, snap the two halves together.
PAGE 26
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE VEHICLE THEFT ALARM This system monitors the vehicle doors and ignition switch for unauthorized entry or operation. When the alarm is activated, the system provides both audible and visual signals. The horn will pulse, headlights/park lights will flash, the Vehicle Theft Alarm/Immobilizer light, located above the driver’s center instrument panel vent will flash, and the vehicle will not start.
PAGE 27
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: • The driver’s door key cylinder and the liftgate button on the keyless entry transmitter cannot arm or disarm the system. • Once the alarm is set, and the liftgate button on the keyless entry transmitter is pressed, on a non-power liftgate vehicle, you have a 30 second one time access into the liftgate area. If the liftgate is not opened within 30 seconds the liftgate will automatically re-lock within 10 seconds.
PAGE 28
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE LIFTGATE The liftgate can be unlocked using the remote keyless entry or by activating the power door lock switches located on the front doors. Once unlocked, the liftgate can be opened or closed. To open the liftgate, depress the liftgate release switch located in the exterior handle and pull the liftgate open with one fluid motion. Liftgate Release The liftgate will not manually open if the vehicle is in gear or the vehicle speed is above 0 mph (0 km/h).
PAGE 29
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE the liftgate. The emergency liftgate latch release can be accessed through a snap-in cover located on the liftgate trim panel. 29 The power liftgate may also be opened by pressing the switch located on the overhead console.
PAGE 30
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! During power operation, personal injury or cargo damage may occur. Ensure the liftgate travel path is clear. Make sure the liftgate is closed and latched before driving away. NOTE: • If anything obstructs the power liftgate while it is closing or opening, the liftgate will automatically reverse to the closed or open position, provided it meets sufficient resistance. • There are also pinch sensors attached to the side of the liftgate.
PAGE 31
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • If the power liftgate encounters multiple obstructions within the same cycle, the system will automatically stop and must be opened or closed manually. WARNING! • Driving with the liftgate open can allow poisonous exhaust gases into your vehicle. You and your passengers could be injured by these fumes. Keep the liftgate closed when you are operating the vehicle.
PAGE 32
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WINDOWS Power Windows The window controls on the driver’s door control all the door windows. The window controls will operate only when the ignition switch is in the ON or ACCESSORY position. The window lock switch on the driver’s door allows you to disable the window controls on the passenger doors. When the lock switch is pressed the window controls on the passenger doors will not illuminate and the passenger windows will be disabled.
PAGE 33
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occurrence and can be minimized. If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting.
PAGE 34
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If your vehicle is equipped with the Occupant Classification System (OCS) there will be a Passenger Airbag Disabled (PAD) Indicator Light located on the center of the instrument panel. NOTE: The front airbags have a multi stage inflator design. This allows the airbag to have different rates of inflation that are based on collision severity. Please pay close attention to the information in this section.
PAGE 35
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 Buckle up even though you are an excellent driver, even on short trips. Someone on the road may be a poor driver and cause a collision that includes you. This can happen far away from home or on your own street. normal conditions. But in a collision, the belt will lock and reduce the risk of your striking the inside of the vehicle or being thrown out.
PAGE 36
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and can take the forces of a collision the best. • Wearing your belt in the wrong place could make your injuries in a collision much worse. You might suffer internal injuries, or you could even slide out of part of the belt.
PAGE 37
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click”.
PAGE 38
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you as well. In a sudden stop you could move too far forward, increasing the possibility of injury. Wear your seat belt snugly. • A belt that is worn under your arm is very dangerous.
PAGE 39
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as possible and keep it snug. • A twisted belt can’t do its job as well. In a collision it could even cut into you. Be sure the belt is straight. If you can’t straighten a belt in your vehicle, take it to your dealer and have it fixed. 5.
PAGE 40
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Adjustable Upper Shoulder Belt Anchorage In the front seats, the shoulder belt anchorage can be adjusted upward or downward to help position the belt away from your neck. Press the button to release the anchorage, and then move it up or down to the position that serves you best. Adjusting Upper Shoulder Belt As a guide, if you are shorter than average, you will prefer a lower position, and if you are taller than average, you’ll prefer a higher position.
PAGE 41
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belt Untwisting Procedure Use the following procedure to untwist a twisted lap/ shoulder belt. 2. At about 6 to 12 inches (15 to 30 cm) above the latch plate, grasp and twist the belt webbing 180° to create a fold that begins immediately above the latch plate. 1. Position the latch plate as close as possible to the anchor point.
PAGE 42
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Slide the latch plate upward over the folded webbing. The folded webbing must enter the slot at the top of the latch plate. Seat Belt Pretensioners The seat belt buckles for both front seating positions are equipped with pretensioning devices that are designed to remove slack from the seat belt in the event of a collision. These devices improve the performance of the seat belt by assuring that the belt is tight about the occupant early in a collision.
PAGE 43
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Enhanced Seat Belt Use Reminder System (BeltAlert) If the driver’s or front passenger’s seat belt has not been buckled within 60 seconds of starting the vehicle and if the vehicle speed is greater than 5 mph (8 km/h), the Enhanced Warning System (BeltAlert) will alert the driver or front passenger to buckle their seat belt. The driver should also instruct all other occupants to buckle their seat belts.
PAGE 44
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Watch for the Seat Belt Warning Light to turn on while unbuckling and off while re-buckling the seat belt. It may be necessary to retract the seat belt. 4. Turn the ignition switch to the OFF position. A single chime will sound to signify that you have successfully completed the programming. The Enhanced Warning System (BeltAlert) can be reactivated by repeating this procedure.
PAGE 45
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 WARNING! Using a seat belt extender when not needed can increase the risk of injury in a collision. Only use when the lap belt is not long enough when it is worn low and snug, and in the recommended seating positions. Remove and store the extender when not needed. Driver and Front Passenger Supplemental Restraint System - Airbag This vehicle has airbags for both the driver and front passenger as a supplement to the seat belt restraint systems.
PAGE 46
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Also, the front passenger airbag is certified to the Federal regulations that define Occupant Classification (Refer to “Occupant Classification System” in this section). This vehicle may also be equipped with a driver inflatable knee blocker located on the instrument panel below the steering column. This vehicle may also be equipped with left and right window bags to protect the driver and passengers sitting next to a window.
PAGE 47
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Do not put anything on or around the airbag covers or attempt to manually open them. You may damage the airbags and you could be injured because the airbags are not there to protect you. These protective covers for the airbag cushions are designed to open only when the airbags are inflating. • If your vehicle is equipped with left and right window bags, do not stack luggage or other cargo up high enough to block the location of the side curtain airbag.
PAGE 48
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Here are some simple steps you can take to minimize the risk of harm from a deploying airbag. 1. Children 12 years old and under should always ride buckled up in a rear seat. Infants in rear facing child restraints should NEVER ride in the front seat of a vehicle with a passenger front airbag. An airbag deployment can cause severe injury or death to infants in that position.
PAGE 49
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly. In some collisions the airbags won’t deploy at all. Always wear your seat belts even though you have airbags. • Being too close to the steering wheel or instrument panel during front airbag deployment could cause serious injury. Airbags need room to inflate.
PAGE 50
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Knee Impact Bolster • Driver Inflatable Knee Blocker • Front Passenger Seat Occupant Classification System (OCS) proper rate of inflation. The front airbag inflators are designed to provide different rates of airbag inflation. • The ORC may modify the rate of inflation based on the occupant size provided by the Occupant Classification Module. − Occupant Classification Module • The ORC will not detect side, roll over, or rear impacts.
PAGE 51
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE first turned on. After the self-check, the AIRBAG warning light will turn off. The PAD indicator light will function normally (Refer to “Passenger Airbag Disable (PAD) Indicator Light” in this section). If the ORC detects a malfunction in any part of the system, it turns on the AIRBAG warning light either momentarily or continuously. A single chime will sound if the light comes on again after initial start up.
PAGE 52
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The Side Impact SRS Window Bags are designed to activate only in certain side collisions. When the ORC and the side impact sensors (with side impact option) detects a collision requiring the window bags to inflate, it signals the inflators on the crash side of the vehicle. A quantity of nontoxic gas is generated to inflate the window bag. The inflating window bag pushes the outside edge of the headliner out of the way and covers the window.
PAGE 53
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • If your vehicle contains a Passenger Airbag Disable indicator light, it will be equipped with the Occupant Classification System (OCS). The OCS system will classify an occupant into a size category based on sensor readings from within the seat cushion. Occupants should try to remain in a normally seated position. If the occupant’s weight is transferred to another object in the vehicle (i.e.
PAGE 54
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE placed on the seat, the light will remain OFF. (The PAD indicator light is an amber light located on the center of the instrument panel above the climate controls.) airbag may or may not be enabled in the event of a collision. Both drivers and passengers should always use the PAD indicator light as an indication if the front passenger is properly positioned or not.
PAGE 55
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 child, and adult. The OCM sends the Occupant Classification to the ORC to identify if a front passenger airbag is allowed. If a fault is present, the AIRBAG warning light is illuminated. is sent to the OCM to ensure that the resultant bladder pressure increase due to applied lap belt tension does not cause a small occupant to be classified as a larger occupant.
PAGE 56
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Unapproved modifications or service procedures to the front passenger seat assembly, its related components, or seat cover may inadvertently change the airbag deployment in case of a frontal crash. This could result in death or serious injury to the front seat passenger if the vehicle is involved in an accident. A modified vehicle may not comply with required Federal Motor Vehicle Safety Standards (FMVSS).
PAGE 57
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If A Deployment Occurs The airbag system is designed to deploy the airbags when the ORC and impact sensors detect a moderate-tosevere collision, to help restrain the vehicle passengers, and then immediately deflate. NOTE: A collision that is not severe enough to need airbag protection will not activate the system. This does not mean something is wrong with the airbag system.
PAGE 58
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Deployed airbags, front seat belt buckle pretensioners and driver inflatable knee blocker cannot protect you in another collision. Have the airbags, front seat belt buckle pretensioners and driver inflatable knee blocker replaced by an authorized dealer as soon as possible. Also, have the Occupant Classification System serviced as well.
PAGE 59
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • You need proper knee impact protection in a collision. Do not mount or locate any aftermarket equipment on or behind the knee bolsters. • It is dangerous to try to repair any part of the airbag system yourself. Be sure to tell anyone who works on your vehicle that it has airbags. 59 Airbag Light You will want to have the airbags ready to inflate for your protection in a collision.
PAGE 60
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Child Restraint Everyone in your vehicle needs to be buckled up at all times — babies and children, too. Every state in the United States and all Canadian provinces require that small children ride in proper restraint systems. This is the law, and you can be prosecuted for ignoring it. Children 12 years and under should ride properly buckled up in a seat appropriate for their age and size.
PAGE 61
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lower Anchors and Tether for CHildren (LATCH) Each vehicle is equipped with two child restraint anchorage systems called LATCH, which stands for Lower Anchors and Tether for CHildren. The LATCH child restraint anchorage systems are installed on second-row seats only. LATCH child restraint anchorage systems are not provided on the six passenger third row seats.
PAGE 62
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Five passenger vehicles are equipped with a second row bench seat only. The two outboard seating positions have lower anchorages that can accommodate rigid mount or flexible webbing-mounted LATCH-compatible child seats. The center seating position of the bench seat can also accommodate a flexible webbing-mounted LATCHcompatible child seat by using the inboard lower anchors of the two outboard seating positions.
PAGE 63
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE convenient. When using the LATCH System, always follow the child restraint manufacturer’s installation instructions. 2 NOTE: If your child restraint seat is not LATCH compatible, install the restraint using the vehicle seat belts. Tether Anchors There are tether strap anchorages behind all second row seating positions and for six passenger vehicles on the driver’s side third row seating position. The tether anchors are located in the rear surface of the seat.
PAGE 64
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE When the tether anchorage is used in the center second row bench seating position or on the third row seating position, where equipped, the strap should be positioned straight over the top of the seatback. When the tether anchorage is used in the third row seating position, the strap should be positioned straight over the top of the seatback.
PAGE 65
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 Infants and Children There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt. Always check the child seat owner’s manual to ensure you have the right seat for your child. Use the restraint that is correct for your child: used either rearward-facing or forward-facing in the vehicle.
PAGE 66
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The belt-positioning booster seat is for children weighing more than 18 kg (40 lbs), but who are still too small to fit the vehicle’s seat belts properly. If the child can not sit with knees bent over the vehicles seat cushion while the child’s back is against the seat back, they should use a belt-positioning booster seat. The child and booster seat are held in the vehicle by the lap/ shoulder belt.
PAGE 67
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Here are some tips on getting the most out of your child restraint: • Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards. We also recommend that you make sure that you can install the child restraint in the vehicle where you will use it, before you buy it. • The restraint must be appropriate for your child’s weight and height. Check the label on the restraint for weight and height limits.
PAGE 68
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Automatic-Locking Retractor (ALR) The center seating position on vehicles equipped with a second row bench seat is equipped with an AutomaticLocking Retractor (ALR). Pull the belt from the retractor until there is enough to allow you to pass through the child restraint and slide the latch plate into the buckle. Then pull on the belt until it is all removed from the retractor.
PAGE 69
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Child restraint systems having attachments designed to connect to the lower anchorages are now available. Child restraints having tether straps and hooks for connection to the seatback tether anchorage have been available for some time. In fact, many child restraint manufacturer’s will provide add-on tether strap kits for some of their older products.
PAGE 70
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Check belt fit periodically. A child’s squirming or slouching can move the belt out of position. Improper installation of a child restraint to the LATCH anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint.
PAGE 71
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ENGINE BREAK-IN RECOMMENDATIONS A long break-in period is not required for the engine in your new vehicle. Drive moderately during the first 300 miles (500 km). After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable. While cruising, brief full-throttle acceleration, within the limits of local traffic laws, contributes to a good break-in. Wide open throttle acceleration in low gear can be detrimental and should be avoided.
PAGE 72
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If it is necessary to sit in a parked vehicle with the engine running, adjust your heating or cooling controls to force outside air into the vehicle. Set the blower at high speed. WARNING! If you are required to drive with the deck lid/liftgate open, make sure that all windows are closed, and the climate control blower switch is set at high speed. DO NOT use the recirculation mode.
PAGE 73
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Periodic Safety Checks You Should Make Outside The Vehicle Tires Examine tires for excessive tread wear or uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread. Inspect tread and sidewall for cuts or cracks. Check wheel nuts for tightness, and tires (including spare) for proper pressure. Lights Have someone observe the operation of exterior lights while you work the controls.
PAGE 74
PAGE 75
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 3 䡵 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79 ▫ Heated Remote Control Mirrors . . . . . . . . . . . .82 ▫ Inside Day / Night Mirror . . . . . . . . . . . . . . . .79 ▫ Illuminated Vanity Mirrors . . . . . . . . . . . . . . . .82 ▫ Automatic Dimming Mirror — If Equipped . . . .80 䡵 Hands–Free Communication (UConnect™) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 76
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 䡵 Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106 ▫ Third Row Seating — If Equipped . . . . . . . . . 116 ▫ 10–Way Driver’s Power Seat — If Equipped . . 106 ▫ Load Floor — If Equipped . . . . . . . . . . . . . . . 117 ▫ 8–Way Driver’s Power Seat — If Equipped . . . 107 ▫ Plastic Grocery Bag Retainer . . . . . . . . . . . . . 118 ▫ 4–Way Passenger’s Power Seat . . . . . . . . . . . . 107 䡵 Driver Memory Seat — If Equipped . . .
PAGE 77
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 77 ▫ Automatic Headlights . . . . . . . . . . . . . . . . . . 128 ▫ Rear Window Wiper/Washer . . . . . . . . . . . . . 131 ▫ Daytime Running Lights (Canada Only) . . . . . 128 䡵 Tilt Steering Column . . . . . . . . . . . . . . . . . . . . 133 ▫ Lights-On Reminder . . . . . . . . . . . . . . . . . . . 128 䡵 Traction Control Switch — If Equipped . . . . . . . 134 ▫ Headlight Time Delay . . . . . . . . . . . . . . . . . .
PAGE 78
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Courtesy/Reading Lights . . . . . . . . . . . . . . . . 142 䡵 Electrical Power Outlets . . . . . . . . . . . . . . . . . . 152 ▫ Sunglasses Storage . . . . . . . . . . . . . . . . . . . . 142 ▫ Electrical Outlet Use With Engine Off . . . . . . . 153 䡵 Garage Door Opener — If Equipped . . . . . . . . . 142 䡵 Cupholders . . . . . . . . . . . . . . . . . . . . . . . . . . . 154 ▫ Programming HomeLink . . . . . . . . . . . . . . . .
PAGE 79
UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Day / Night Mirror Adjust the mirror to center on the view through the rear window. A two point pivot system allows for horizontal and vertical adjustment of the mirror. MANUAL REARVIEW MIRROR 79 Annoying headlight glare can be reduced by moving the small control under the mirror to the night position (toward rear of vehicle). The mirror should be adjusted while set in the day position (toward windshield).
PAGE 80
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Dimming Mirror — If Equipped If the switch is in the “Auto” position the mirror will automatically adjust for annoying headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light in the mirror will illuminate to indicate when this feature is on. CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror.
PAGE 81
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Outside Mirror — Driver’s Side Adjust the outside mirror to center on the adjacent lane of traffic, with a slight overlap of the view obtained on the inside mirror. Outside Mirror — Passenger’s Side Adjust the convex outside mirror so you can just see the side of your vehicle in the portion of the mirror closest to the vehicle. This type of mirror will give a much wider view to the rear, and especially of the lane next to your vehicle.
PAGE 82
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Remote-Control Mirrors Use the mirror select switch, located on the driver’s door trim panel above the power window switches, to adjust the view obtained in the outside mirrors. Press the rocker switch to the L or R for Left or Right mirror selection. Use the center off position to guard against accidentally moving a mirror position. Select a mirror and press one of the four arrows for the direction you want the mirror to move.
PAGE 83
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Sun Visor Extension The sun visors may be pulled out to provide extended coverage of the side glass. HANDS–FREE COMMUNICATION (UConnect™) — IF EQUIPPED UConnect™ is a voice-activated, hands-free, in- vehicle communications system. UConnect™ allows you to dial a phone number with your cellular phone using simple voice commands (e.g., ⬙Call” ѧ “Mike” ѧ”Work⬙ or ⬙Dial” ѧ “248-555-1212⬙).
PAGE 84
UNDERSTANDING THE FEATURES OF YOUR VEHICLE with the system at a time. The system is available in English, Spanish, or French languages (as equipped). The rearview mirror contains the microphone for the system and the control buttons that will enable you to access the system. The UConnect™ system can be used with any HandsFree Profile certified Bluetooth™ cellular phone. See www.chrysler.com/uconnect for supported phones. If your cellular phone supports a different profile (e.g.
PAGE 85
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Operations Voice commands can be used to operate the UConnect™ system and to navigate through the UConnect™ menu structure. Voice commands are required after most UConnect™ system prompts. You will be prompted for a specific command and then guided through the available options. • Prior to giving a voice command, one must wait for the voice on beep, which follows the ⬙Ready⬙ prompt or another prompt.
PAGE 86
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Cancel Command At any prompt, after the voice on beep, you can say ⬙Cancel⬙ and you will be returned to the main menu. However, in a few instances the system will take you back to the previous menu. NOTE: • www.chrysler.com/uconnect Pair (Link) UConnect™ System to a Cellular Phone To begin using your UConnect™ system, you must pair your compatible Bluetooth™ enabled cellular phone.
PAGE 87
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The UConnect™ system will then prompt you to begin the cellular phone pairing process on your cellular phone. Before attempting to pair phone, please see your cellular phone’s user manual (Bluetooth section) for instructions on how to complete this step. • For identification purposes, you will be prompted to give the UConnect™ system a name for your cellular phone. Each cellular phone that is paired should be given a unique phone name.
PAGE 88
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 234-567-890 is nine digits long, which is not a valid phone number - the closest valid phone number has ten digits. • The UConnect™ system will confirm the phone number and then dial. The number will appear in the display of certain radios. Call by Saying a Name • Press the “Phone” button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Call.⬙ • System will prompt you to say the name of the person you want call.
PAGE 89
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • When prompted, say the name of the new entry. Use of long names helps the voice recognition and is recommended. For example, say ⬙Robert Smith⬙ or ⬙Robert⬙ instead of ⬙Bob.⬙ • When prompted, enter the number designation (e.g.: ⬙Home,⬙ ⬙Work,⬙ ⬙Mobile,⬙ or ⬙Pager⬙). This will allow you to store multiple numbers for each phonebook entry, if desired. 89 four associated phone numbers and designations.
PAGE 90
UNDERSTANDING THE FEATURES OF YOUR VEHICLE After you are finished editing an entry in the phonebook, you will be given the opportunities to edit another entry in the phonebook, call the number you just edited, or return to the main menu. ⬙Phonebook Edit⬙ can be used to add another phone number to a name entry that already exists in the phonebook. For example, the entry John Doe may have a mobile and a home number, but you can add John Doe’s work number later using the ⬙Phonebook Edit⬙ feature.
PAGE 91
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Delete All Entries in the UConnect™ Phonebook • Press the ’Phone’ button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Phonebook Erase All.⬙ • The UConnect™ system will ask you to verify that you wish to delete all the entries from the phonebook. • After confirmation, the phonebook entries will be deleted. List All Names in the UConnect™ Phonebook • Press the ’Phone’ button to begin.
PAGE 92
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Answer or Reject an Incoming Call - No Call Currently in Progress When you receive a call on your cellular phone, the UConnect™ system will interrupt the vehicle audio system, if on, and will ask if you would like to answer the call. To reject the call, press and hold the ’Phone’ button until you hear a single beep indicating that the incoming call was rejected.
PAGE 93
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Toggling Between Calls If two calls are in progress (one active and one on hold), press the ’Phone’ button until you hear a single beep indicating that the active and hold status of the two calls have switched. Only one call can be placed on hold at one time.
PAGE 94
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Call Continuation Call continuation is progression of a phone call on UConnect™ system after the vehicle ignition key has been switched to off.
PAGE 95
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 Emergency Assistance If you are in an emergency and the mobile phone is reachable: The UConnect™ system does slightly lower your chances of successfully making a phone call as to that for the cell phone directly. • Pick up the phone and manually dial the emergency number for your area.
PAGE 96
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Please refer to the 24-Hour “Towing Assistance” coverage details in the Warranty information booklet and on the 24–Hour Towing Assistance Card. Paging To learn how to page, refer to ⬙Working with Automated Systems.⬙ Paging works properly except for pagers of certain companies which time-out a little too soon to work properly with the UConnect™ system. Voice Mail Calling To learn how to access your voice mail, refer to ⬙Working with Automated Systems.
PAGE 97
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 Barge In - Overriding Prompts The ’Voice Recognition’ button can be used when you wish to skip part of a prompt and issue your voice recognition command immediately. For example, if a prompt is playing ⬙Would you like to pair a phone, clear aѧ,⬙ you could press the ’Voice Recognition’ button and say ⬙Pair a Phone⬙ to select that option without having to listen to the rest of the voice prompt.
PAGE 98
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Certain brands of mobile phones do not send the dial ring to the UConnect™ system to play it on the vehicle audio system, so you will not hear it. Under this situation, after successfully dialing a number, the user may feel that the call did not go through even though the call is in progress. Once your call is answered, you will hear the audio.
PAGE 99
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99 Connect or Disconnect Link Between the UConnect™ System and Cellular Phone Your cellular phone can be paired with many different electronic devices, but can only be actively ⬙connected⬙ with one electronic device at a time. the lowest priority. To “select” or “delete” a paired phone being announced, press the ⬘Voice recognition’ button and say “Select” or “Delete.” Also, see the next two sections for an alternate way to “select” or “delete” a paired phone.
PAGE 100
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • When prompted say the priority number of the cellular phone you wish to select. You can also press the ⬘Voice Recognition’ button anytime while the list is being played, then say the priority number of the phone that you wish to select. • The selected phone will be used for the next phone call.
PAGE 101
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Performance is maximized under: • low-to-medium blower setting, • low-to-medium vehicle speed, • low road noise, • smooth road surface, • fully closed windows, • dry weather condition. • Even though the system is designed for users speaking in North American English, French, and Spanish accents, the system may not always work for some.
PAGE 102
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • smooth road surface, • fully closed windows, and • dry weather condition. • Operation from driver seat. • Performance, such as, audio clarity, echo. and loudness to a large degree, rely on the phone and network, and not the UConnect™ system. • Echo at far end can sometime be reduced by lowering the in-vehicle audio volume. Bluetooth Communication Link Cellular phones have been found to occasionally lose connection to the UConnect™ system.
PAGE 103
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 3
PAGE 104
UNDERSTANDING THE FEATURES OF YOUR VEHICLE
PAGE 105
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 3
PAGE 106
UNDERSTANDING THE FEATURES OF YOUR VEHICLE North American English Primary Alternate(s) Zero Oh Add location Add new All All of them Confirmation prompts Confirmations prompts Delete a name Delete Language Select language List names List all List paired phones List phones Pager Beeper Phone pairing Pairing Phonebook Phone book Return to main menu Return.
PAGE 107
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 WARNING! Adjust the seat only while the vehicle is parked. Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. 10–Way Driver’s Power Seat 8–Way Driver’s Power Seat — If Equipped The driver’s power seat switches are located on the driver’s front door trim panel.
PAGE 108
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Do not place any article under a power seat or impede its ability to move as it may cause damage to the seat controls. Seat travel may become limited if movement is stopped by an obstruction in the seat’s path. Adjustable Head Restraints Head restraints can reduce the risk of whiplash injury in the event of impact from the rear. Pull up or push down on the head restraint so that the upper edge is as high as practical.
PAGE 109
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 once to select a heat setting (high or low) and press the switch a second time in the same direction to turn the heated seat off. The indicator light will show when LOW or HIGH heat is ON. 3 Front Heated Seat Switch Press the switch once to select a heat setting (high or low) and press the switch a second time in the same direction to turn the heated seat off. The indicator light will show when LOW or HIGH heat is ON.
PAGE 110
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: • If the lights in the second row heated seat switch begin to flash when the switch is pressed, it indicates that the heated seat is not functioning properly and that service is required. See your authorized dealer for service. • Once a heat setting is selected, heat will be felt within 2 to 3 minutes. • The heated seats will turn off when the ignition switch is turned to the OFF position.
PAGE 111
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 WARNING! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or fatally injured. Use the recliner only when the vehicle is parked. Second Row Manual Seat Adjuster — If Equipped The adjusting bar is located under the front of the seat. Pull the bar up and move the seat to the desired position. Release the bar to lock the seat into position.
PAGE 112
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Adjust the seat only while the vehicle is parked. Adjusting a seat while the vehicle is moving is dangerous. The seat belt might not be properly adjusted and you could be injured. Second Row Bench Seating — If Equipped The second row seats may be used with either or both seatbacks folded forward for additional storage space. To fold the seat, remove any objects from in front of or on the seat.
PAGE 113
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Be sure there is nothing in front of the second row seat cushion before folding it down. Damage to the seat may occur. 113 4. Pull up on the seatback release lever located on the outboard side of the seat labeled “1” and fold the seatback down. 3 Second Row Fold & Tumble Seats — If Equipped The second row seats can be folded and tumbled forward for easy access to the third seat or rear cargo area. To fold and tumble the seat, follow these steps: 1.
PAGE 114
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 5. Pull up on the release handle labeled “2” and lift firmly to tumble the seat fully forward. If the seat contacts the rear of the front seat, move the front seat forward. To relatch the seat, tilt the seat rearward and push down firmly to engage the rear attachments. Then lift the seatback release lever labeled “1” and pull the seatback up to return it to its full upright position.
PAGE 115
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 To fold and tumble the seat forward, follow these steps: 1. Pull up on the seatback release handle “1” located on the back of the seat to fold the seatback down. 3 Release Strap 2 Location Release Handle 1 Location 2. Pull the release strap “2” located at the bottom of the seat to lift and tumble the seat forward. To relatch the seat, tilt the seat rearward and push down firmly to engage the rear attachments.
PAGE 116
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Third Row Seating — If Equipped The third row seats may be used with either or both seatbacks folded forward for additional storage space. To fold the seat, remove any objects from in front of or on the seat. Then pull handle located on the seatback and push it forward. WARNING! Do not sit in the 3rd row seat with the second row seatbacks folded or with the second row seats folded and tumbled.
PAGE 117
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Not all head restraints in this vehicle are the same. Head restraints from one seating position should not be removed and installed in any other seating position. In a collision, serious injury or death may result if the proper head restraint is not installed on each seat. • The cargo area in the rear of the vehicle should not be used as a play area by children. They could be seriously injured in a collision.
PAGE 118
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Pull on the load floor strap and lift the panel from the driver’s second row seatback over the center console and onto the passenger second row seat. Plastic Grocery Bag Retainer Retainer hooks which will hold plastic grocery bag handles are built into the seatbacks of all front seats. The floor supports the partial weight of the bagged goods. Load Floor Panel NOTE: Be sure to reattach the strap to secure the load floor panel when not in use.
PAGE 119
UNDERSTANDING THE FEATURES OF YOUR VEHICLE DRIVER MEMORY SEAT — IF EQUIPPED If your vehicle is equipped with memory systems, your remote keyless entry transmitter or memory seat buttons on the driver’s door panel can be used to recall the driver’s seat, outside mirrors, adjustable pedals (if equipped) and radio station presets to saved positions. 119 The memory seat buttons located on the driver’s door will always recall stored settings.
PAGE 120
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Your vehicle has been delivered with two remote keyless entry transmitters. One or both transmitters can be linked to either memory position. Up to eight remote keyless entry transmitters can be used with your vehicle. The memory seat system can also accommodate up to eight transmitters linked to either of the two stored seat positions or any combination of the two positions. To Program Memory Seat Buttons & RKE Transmitters, Follow These Steps: 1.
PAGE 121
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Repeat the above steps for the second position using the other driver’s door numbered button and Remote Keyless Entry Transmitter. Each time the SET (S) button and a numbered button are pressed, you erase the old memory and store a new one. To Disable A Transmitter Link, Follow These Steps: 1. Select “Remote Linked To Memory” from the Electronic Vehicle Information Center, Customer Programmable features. 2.
PAGE 122
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Easy Entry/Exit Seat (Available with Memory Seat Only) This feature provides automatic driver’s seat positioning which will enhance driver mobility out of and into the vehicle. 120 mm) forward of the rear stop when the key is removed from the ignition switch. The seat will move forward to the memory/driving position when the key is placed into the ignition and turned out of the LOCK position.
PAGE 123
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Tilt Mirrors in Reverse — If Equipped This additional feature provides automatic outside mirror positioning which will aid the driver’s view of the ground rearward of the front doors. The outside mirrors will move slightly downward from the present position when the vehicle is shifted into the Reverse position. The outside mirrors will then return to the original position when the vehicle is shifted out of Reverse position.
PAGE 124
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Next, push to the left the safety catch located under the front edge of the hood, near the center. To prevent possible damage, do not slam the hood to close it. Lower the hood until it is open approximately 15 cm (6 inches) and then drop it. This should secure both latches. Never drive your vehicle unless the hood is fully closed, with both latches engaged.
PAGE 125
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 LIGHTS Overhead Console Map/Reading Lights These lights are mounted between the sun visors on the overhead console. Each light is turned ON by pressing the lens. Press the lens a second time to turn the light OFF. The lights also turn on when a door is opened or the dimmer control is turned fully upward, past the second detent.
PAGE 126
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Interior Lights The interior lights come on when a door is opened. The interior lights will automatically turn off in about 15 minutes if a door is left open or the dimmer control is left in the Dome light position. Turn the ignition switch ON to restore the interior light operation.
PAGE 127
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To change the brightness of the instrument panel lights, rotate the center portion of the Multi-Function Lever up or down. Dimmer Control With the parking lights or headlights on, rotating the dimmer control for the interior lights on the Multi-Function Lever upward will increase the brightness of the instrument panel lights. 127 Dome Light Position Rotate the dimmer control completely upward to the second detent to turn on the interior lights.
PAGE 128
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Parade Mode (Daytime Brightness Feature) Rotate the dimmer control upward to the first detent. This feature brightens the odometer and radio display when the parking lights or headlights are on during daylight conditions. Automatic Headlights This system automatically turns your headlights ON or OFF based on ambient light levels. To turn the system ON, turn the end of the Multi-Function Lever to the third detent position.
PAGE 129
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To activate the delay feature, turn off the ignition switch while the headlights are still on. Then turn off the headlights within 45 seconds. The 90 second delay interval begins when headlight switch is turned off. If the headlights or park lights are turned back on or the ignition switch is turned on, the delay will be cancelled. If the headlights are turned off before the ignition, they will turn off in the normal manner.
PAGE 130
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Highbeam/Lowbeam Select Switch Pull the Multi-Function Lever towards you to switch the headlights to HIGH beam. Pull the Lever a second time to switch the headlights to LOW beam. Passing Light You can signal another vehicle with your headlights by lightly pulling the Multi-Function Lever toward you. This will cause the headlights to turn on at high beam and remain on until the lever is released.
PAGE 131
UNDERSTANDING THE FEATURES OF YOUR VEHICLE If the lever is pulled while in the OFF position, the wipers will operate for two wipe cycles, then turn OFF. Mist Feature Push down on the wiper lever to activate a single wipe to clear off road mist or spray from a passing vehicle. As long as the lever is held down, the wipers will continue to operate. 131 select the desired delay interval. The delay can be regulated from a maximum of approximately 23 seconds between cycles, to a cycle every second.
PAGE 132
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rotating the center of the switch up to the DEL (Delay) position or the ON position will activate the rear wiper. Push the lever forward to initiate the rear wash function in any of the three positions. The washer pump will continue to operate as long as the lever is pressed. Upon release, the rear wiper will cycle two times before returning to the set position.
PAGE 133
UNDERSTANDING THE FEATURES OF YOUR VEHICLE TILT STEERING COLUMN To tilt the column, pull the lever, located behind the turn signal control, toward you and move the steering wheel up or down, as desired. Release the lever to lock the steering wheel firmly in place. Tilt Steering Column Control 133 WARNING! Tilting the steering column while the vehicle is moving is dangerous. Without a stable steering column, you could lose control of the vehicle and have an accident.
PAGE 134
UNDERSTANDING THE FEATURES OF YOUR VEHICLE TRACTION CONTROL SWITCH — IF EQUIPPED The traction control Indicator, located in the instrument cluster, will light up when the Traction Control is in use. To turn the system OFF, press the Traction Control switch located on center console next to the ash tray, until the traction control Indicator in the instrument cluster lights up.
PAGE 135
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To turn the system back ON, press the switch a second time until the traction control Indicator turns OFF. NOTE: • The traction control Indicator comes on each time the ignition switch is turned ON. This will occur even if you used the switch to turn the system OFF. inches (150 cm). A warning display above the rear window provides both visible and audible warnings indicating the range of the object.
PAGE 136
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Drivers must be careful when backing up even when using the Rear Park Assist System. Always check carefully behind your vehicle, look behind you, and be sure to check for pedestrians, other vehicles, obstructions, and blind spots before backing up. Failure to do so can result in serious personal injury or death. The display contains two sets of yellow and red LEDs that the driver can see in the rear view mirror.
PAGE 137
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 ADJUSTABLE PEDALS — IF EQUIPPED This feature allows both the brake and accelerator pedals to move toward or away from the driver to provide improved position with the steering wheel. The adjustable pedal system is designed to allow a greater range of driver comfort for steering wheel tilt and seat position. The switch is located on the drivers door trim panel next to the power seat switches.
PAGE 138
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The pedals can be adjusted while driving. CAUTION! • The pedals cannot be adjusted when the vehicle is in R (Reverse) or when the Speed Control is ON. A message will be displayed in the Electronic Vehicle Information Center (EVIC) if the pedals are attempted to be adjusted when the system is locked out (“Adjustable Pedal Disabled — Cruise Control Engaged” or “Adjustable Pedal Disabled — Vehicle In Reverse”).
PAGE 139
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 WARNING! Leaving the Electronic Speed Control system on when not in use is dangerous. You could accidently set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the system OFF when you aren’t using it.
PAGE 140
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Deactivate: A soft tap on the brake pedal, pushing the “CANCEL” button or normal braking while slowing the vehicle will deactivate the speed control without erasing the memory. Pushing the “ON/OFF” button to the OFF position or turning off the ignition erases the speed memory. To Resume Speed: To resume a previously set speed, push and release the “ACCEL/RESUME” button. Resume can be used at any speed above 25 mph (40 km/h).
PAGE 141
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Four speed automatic transmissions will experience a downshift to 3rd gear while climbing uphill or descending downhill. This downshift to 3rd gear is necessary to maintain vehicle set speed. On steep hills a greater speed loss or gain may occur so it may be preferable to drive without speed control.
PAGE 142
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Courtesy/Reading Lights At the forward end of the console are two courtesy/ reading lights. Press the lens to turn these lights on. Press a second time to turn the lights off. The lights also turn on when a front door, a rear door or the liftgate is opened. The lights will also turn on when the unlock button on the remote keyless entry transmitter is pressed.
PAGE 143
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 WARNING! WARNING! A moving garage door can cause injury to people and pets in the path of the door. People or pets could be seriously or fatally injured. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by federal safety standards. This includes most garage door opener models manufactured after 1982. Do not use a garage door opener without these safety features it could cause injury or death.
PAGE 144
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Programming HomeLink NOTE: When programming a garage door opener, it is advised to park outside the garage. Some vehicles may require the ignition switch to be turned to the second (or ⬙accessories⬙) position for programming and/or operation of HomeLink. It is also recommended that a new battery be placed in the hand-held transmitter of the device being programmed to HomeLink for quicker training and accurate transmission of the radio-frequency signal. 1.
PAGE 145
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Simultaneously press and hold both the HomeLink button that you want to train and the hand-held transmitter buttons. Do not release the buttons until step 4 has been completed. NOTE: Some gate operators and garage door openers may require you to replace this Programming Step 3 with procedures noted in the ⬙Gate Operator/Canadian Programming⬙ section. 4.
PAGE 146
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 6. At the garage door opener receiver (motor-head unit) in the garage, locate the ⬙learn⬙ or ⬙smart⬙ button. This can usually be found where the hanging antenna wire is attached to the motor-head unit. NOTE: To program the remaining two HomeLink buttons, begin with ⬙Programming⬙ step two. Do not repeat step one. For questions or comments, please contact HomeLink at www.homelink.com or 1-800-355-3515. 7.
PAGE 147
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Continue to press and hold the HomeLink button while you press and release every two seconds (⬙cycle⬙) your hand-held transmitter until the frequency signal has successfully been accepted by HomeLink. The indicator light will flash slowly and then rapidly and the EVIC display will show “Channel X Trained” (where X is Channel 1, 2, or 3). Proceed with ⬙Programming⬙ step four to complete.
PAGE 148
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. The indicator light will begin to flash after 20 seconds and the EVIC display will show “Channel X Transmit” (where X is Channel 1, 2, or 3) for 20 seconds and then change to “Channel X Training”. Without releasing the HomeLink button, proceed with ⬙Programming⬙ step 2 This device complies with part 15 of FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference.
PAGE 149
UNDERSTANDING THE FEATURES OF YOUR VEHICLE POWER SUNROOF — IF EQUIPPED The power sunroof buttons are located between the sun visors on the overhead console. 149 Press and hold the “OPEN” button rearward to fully open the sunroof. The sunroof can be stopped at any position between closed and full open. Momentarily pressing the “OPEN” button rearward will activate the Express Open Feature, causing the sunroof to open automatically. Press and hold the “VENT” button to open the vent.
PAGE 150
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Express Open Feature The sunroof is equipped with an intermediate stop or comfort stop position. This feature is designed to eliminate wind buffeting at vehicle speeds between 20-40 mph (32-64 km/h). To operate this feature, momentarily press the “OPEN” button rearward to activate the Express Open Feature and the glass will automatically stop at the comfort stop position. Pressing the button rearward again will fully open the sunroof.
PAGE 151
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Never leave children in a vehicle, with the keys in the ignition switch. Occupants, particularly unattended children, can become entrapped by the power sunroof while operating the power sunroof buttons. Such entrapment may result in serious injury or death. • In an accident, there is a greater risk of being thrown from a vehicle with an open sunroof. You could also be seriously injured or killed.
PAGE 152
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ELECTRICAL POWER OUTLETS There are two 12 volt power outlets located on the instrument panel below the radio. The driver’s side outlet is controlled by the ignition switch and the passenger side outlet is connected directly to the battery. The driver’s side outlet will also operate a conventional cigar lighter unit (if equipped with an optional Smoker’s Package).
PAGE 153
UNDERSTANDING THE FEATURES OF YOUR VEHICLE A third outlet is located on the back of the front center console near the floor, and is also controlled by the ignition switch. A fourth outlet is located on the driver’s side, in the rear cargo area and is also controlled by the ignition switch. The outlets include tethered caps labeled with a key or battery symbol indicating the power source.
PAGE 154
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CUPHOLDERS Front Seat Cupholders The cupholders are located in the forward edge of the center console. Push down on the forward edge of the console to release the cupholders. Press the cover up when the cupholders are no longer needed. Six Passenger Seating Cupholders Second Row Seat Cupholders On vehicles equipped with five passenger seating the second row seat cupholders are located in middle of the seatback armrest.
PAGE 155
UNDERSTANDING THE FEATURES OF YOUR VEHICLE On vehicles equipped with six passenger seating the second row seat cupholders are located in the forward edge of the center console located between the second row seats. Push down on the forward edge of the console to release the cupholders. Press the cover up when the cupholders are no longer needed. Rear Cargo Storage Bin — If Equipped The storage bin is located in the floor of the rear cargo area. To open lift up on the handle.
PAGE 156
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Retractable Cargo Area Cover — If Equipped To cover the cargo area: 1. Fold down the third row seatbacks. 2. Unfold the cargo cover extensions and lock into place. 3. Insert the pins on the ends of the cover into the slots located on the trim panel behind the second row seatbacks. 4. Grasp the center portion of the cover flap. Pull it over the cargo area. 5. Insert the pins on the ends of the cover flap into the slots on the rear trim panel. 6.
PAGE 157
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Grasp the center portion of the cover flap. Pull it over the cargo area. 5. Insert the pins on the ends of the cover flap into the slots on the rear trim panel. 6. The liftgate may be opened or closed with the cargo cover in place. Cargo Tie-Down Hooks The tie-downs located on cargo area floor and on the rear trim panels should be used to safely secure loads when vehicle is moving.
PAGE 158
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Place as much cargo as possible in front of the rear axle. Too much weight or improperly placed weight over or behind the rear axle can cause the rear of the vehicle to sway. • Do not pile luggage or cargo higher than the top of the seatback. This could impair visibility or become a dangerous projectile in a sudden stop or collision.
PAGE 159
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Distribute cargo weight evenly on the roof rack crossbars. The roof rack does not increase the total load carrying capacity of the vehicle. Be sure the total load of cargo inside the vehicle plus that on the external rack does not exceed the maximum vehicle load capacity. To move the cross bars, press the upper edge of each cross bar button, then move the cross bar to the desired position, keeping the crossbars parallel to the rack frame.
PAGE 160
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! WARNING! • Crossbars should remain equally spaced or parallel at any luggage rack position for proper function. Noncompliance could result in damage to the luggage rack, cargo and/or vehicle. • To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity of 150 lbs (68 kg). Always distribute heavy loads as evenly as possible and secure the load appropriately.
PAGE 161
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 Instruments And Controls . . . . . . . . . . . . . . . . . 165 ▫ Compass Display — If Equipped . . . . . . . . . . 183 䡵 Base Instrument Cluster . . . . . . . . . . . . . . . . . . 166 ▫ Mini-Trip Functions — If Equipped . . . . . . . . 185 䡵 Premium Instrument Cluster . . . . . . . . . . . . . . . 167 䡵 Setting The Analog Clock . . . . . . . . . . . . . . . . . 186 䡵 Instrument Cluster Descriptions . . . . . . . . . . . .
PAGE 162
UNDERSTANDING YOUR INSTRUMENT PANEL ▫ CD/DVD Changer Operation . . . . . . . . . . . . . 193 ▫ Radio Operation . . . . . . . . . . . . . . . . . . . . . . 207 ▫ Notes On Playing MP3 Files . . . . . . . . . . . . . 193 ▫ Tape Player Operation . . . . . . . . . . . . . . . . . . 211 ▫ Operation Instructions - (CD Mode For MP3 Audio Play) . . . . . . . . . . . . . . . . . . . . . . . . . 195 ▫ CD Player Operation . . . . . . . . . . . . . . . . . . .
PAGE 163
UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Prog Up/Down Buttons (10, 11) . . . . . . . . . . . 219 ▫ Slow Button (12) . . . . . . . . . . . . . . . . . . . . . . 219 ▫ Stop Button (13) . . . . . . . . . . . . . . . . . . . . . . 219 ▫ Menu Button (14) . . . . . . . . . . . . . . . . . . . . . 219 ▫ Next/Prev Buttons (2, 15) . . . . . . . . . . . . . . . 220 ▫ FF/RW Buttons (3, 16) . . . . . . . . . . . . . . . . . . 220 ▫ Enter Button (17) . . . . . . . . . . . . . . . . . . . . . 220 ▫ Light Button (18) . . .
PAGE 164
UNDERSTANDING YOUR INSTRUMENT PANEL ▫ PTY Button ⬙Seek⬙ . . . . . . . . . . . . . . . . . . . . . 228 ▫ FM Reception . . . . . . . . . . . . . . . . . . . . . . . . 231 ▫ Satellite Antenna . . . . . . . . . . . . . . . . . . . . . . 228 䡵 Cassette Tape And Player Maintenance . . . . . . . 232 ▫ Reception Quality . . . . . . . . . . . . . . . . . . . . . 229 䡵 CD/DVD Disc Maintenance . . . . . . . . . . . . . . . 233 䡵 Remote Sound System Controls . . . . . . . . . . . . .
PAGE 165
UNDERSTANDING YOUR INSTRUMENT PANEL 165 INSTRUMENTS AND CONTROLS 4
PAGE 166
UNDERSTANDING YOUR INSTRUMENT PANEL BASE INSTRUMENT CLUSTER
PAGE 167
UNDERSTANDING YOUR INSTRUMENT PANEL 167 PREMIUM INSTRUMENT CLUSTER 4
PAGE 168
UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTIONS 1. Voltage Light This light monitors the electrical system voltage. The light should turn on momentarily as the engine is started. If the light stays on or turns on while driving, it indicates a problem with the charging system. Immediate service should be obtained. 2. Temperature Gauge The temperature gauge shows engine coolant temperature.
PAGE 169
UNDERSTANDING YOUR INSTRUMENT PANEL WARNING! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call a service center if your vehicle overheats. If you decide to look under the hood yourself, see Section 7 of this manual. Follow the warnings under the Cooling System Pressure Cap paragraph. 3. Fuel Gauge The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON position.
PAGE 170
UNDERSTANDING YOUR INSTRUMENT PANEL is not functioning and that service is required. However, the conventional brake system will continue to operate normally if the BRAKE warning light is not on. indicated by the Brake Warning Light which will turn on when the brake fluid level in the master cylinder has dropped below a specified level. If the ABS light is on, the brake system should be serviced as soon as possible to restore the benefits of Anti-Lock brakes.
PAGE 171
UNDERSTANDING YOUR INSTRUMENT PANEL Vehicles equipped with Anti-Lock brakes (ABS), are also equipped with Electronic Brake Force Distribution (EBD). In the event of an EBD failure, the Brake Warning Light will turn on along with the ABS Light. Immediate repair to the ABS system is required. The operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON position. The light should illuminate for approximately two seconds.
PAGE 172
UNDERSTANDING YOUR INSTRUMENT PANEL disabled for about 4 minutes until the brakes have cooled. The system will automatically reactivate and turn off the Traction Control Light. 11. Transmission Range Indicator This display indicator shows the automatic transmission gear selection. 9. Tachometer The red segments indicate the maximum permissible engine revolutions-per-minute (r.p.m. x 1000) for each gear range. Before reaching the red area, ease up on the accelerator. 12.
PAGE 173
UNDERSTANDING YOUR INSTRUMENT PANEL The two trip odometers show individual trip mileage. To switch from odometer to trip odometers, press and release the Trip Odometer button. To reset a trip odometer, display the desired trip odometer to be reset then push and hold the button until the display resets (approximately 2 seconds).
PAGE 174
UNDERSTANDING YOUR INSTRUMENT PANEL 16. High Beam Light This light shows that the headlights are on high beam. Pull the Multi-Function lever towards the steering wheel to switch the headlights from high or low beam. 17. Navigation Screen — If Equipped The navigation system provides maps, turn identification, selection menus and instructions for selecting a variety of destinations and routes. Refer to your “Navigation User’s Manual” for detailed operating instructions. 18.
PAGE 175
UNDERSTANDING YOUR INSTRUMENT PANEL 21. Tire Pressure Monitoring Telltale Lamp — If Equipped Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.
PAGE 176
UNDERSTANDING YOUR INSTRUMENT PANEL 23. Electronic Vehicle Information Center Display — If Equipped When the appropriate conditions exist, this display shows the Electronic Vehicle Information Center (EVIC) messages. 24. Engine Temperature Warning Light This light warns of an overheated engine condition. If this light is accompanied by a continuous chime, the engine temperature is critically hot, and the vehicle should be turned off immediately. The vehicle should be serviced as soon as possible. 25.
PAGE 177
UNDERSTANDING YOUR INSTRUMENT PANEL 177 Pressing the MENU button will change the displayed programming features. Pressing the STEP button will display the available choices. Pressing the MENU button a second time accepts a selected choice. • PROGRAM KEY & FOB When the appropriate conditions exist, the Electronic Vehicle Information Center (EVIC) displays the following messages.
PAGE 178
UNDERSTANDING YOUR INSTRUMENT PANEL • UNLOCK TO OPEN LIFTGATE (with a single chime) • WASHER FLUID LOW (with a single chime) • PUT IN PARK FOR LIFTGATE (with a single chime) • PEDAL ADJUST DISABLED CRUISE ENGAGED • TOO COLD FOR PWR LIFTGATE (with a single chime) • PEDAL ADJUST DISABLED VEHICLE IN REVERSE • TOO HOT FOR PWR LIFTGATE (with a single chime) • PERFORM SERVICE (with a single chime) • LEFT/RIGHT FRONT DOOR AJAR (one or more, with a single chime if speed is above 1 mph) • LEFT/RIGHT REAR
PAGE 179
UNDERSTANDING YOUR INSTRUMENT PANEL 179 • 1,2,3 OR 4 TIRE(S) LOW PRESSURE (Refer to ”Tire Pressure Monitor System” in the “Starting And Operating, Tire Section”) Customer Programmable Features — If Equipped Press the MENU button until one of the following display choices appears: • CHECK TPM SYSTEM (Refer to ”Tire Pressure Monitor System” in the “Starting And Operating, Tire Section”) Language? When in this display you may select one of three languages for all display nomenclature, including the trip c
PAGE 180
UNDERSTANDING YOUR INSTRUMENT PANEL ASSIST DISABLED after the feature has been disabled and SERVICE PARK ASSIST SYSTEM if there is a problem with the system. Display U.S. or Metric? Pressing the US/M button will change the EVIC, odometer, navigation system and A/C Control units from US to Metric. Use factory Settings? When in this display you may select to use the factory settings and no programmable features will be offered.
PAGE 181
UNDERSTANDING YOUR INSTRUMENT PANEL Remote Linked To Memory? (Available with Memory Seat Only) When this feature is selected the memory seat, mirror, and radio settings will return to the memory set position when the remote keyless entry “Unlock” button is pressed. If this feature is not selected then the memory seat, mirror, and radio settings can only return to the memory set position using the door mounted switch. Pressing the STEP button when in this display will select “Yes” or “No.
PAGE 182
UNDERSTANDING YOUR INSTRUMENT PANEL turn off when the wipers are turned off if they were turned on in this way. Pressing the STEP button when in this display will select “Yes” or “No.” NOTE: Turning the headlights on during the daytime causes the instrument panel lights to dim. To increase the brightness, refer to “Lights” in this section.
PAGE 183
UNDERSTANDING YOUR INSTRUMENT PANEL The Easy Entry Easy Exit feature is not enabled when the vehicle is delivered from the factory. The Easy Entry Easy Exit feature is enabled (or later disabled) through the programmable features in the Electronic Vehicle Information Center (EVIC). Pressing the STEP button when in this display will select “Yes” or “No.
PAGE 184
UNDERSTANDING YOUR INSTRUMENT PANEL Manual Compass Calibration If the compass appears erratic and the “COMPASS CALIBRATING” message does not appear in the EVIC display, you must put the compass into the Calibration Mode manually. To put into a Calibration Mode: Turn on the ignition switch and set the display to Compass. Press the RESET button for at least 10 seconds until the “COMPASS CALIBRATING” message appears.
PAGE 185
UNDERSTANDING YOUR INSTRUMENT PANEL 185 To set the variance: Turn the ignition switch ON and set the display to Compass. Press the RESET button for approximately 5 seconds but no more than 10 seconds. The “COMPASS VARIANCE” message and the last variance zone number will be displayed. Press the STEP button to select the proper variance zone as shown in the map. Press the RESET button to set the new variance zone and resume normal operation.
PAGE 186
UNDERSTANDING YOUR INSTRUMENT PANEL • Off Mode Shows a blank display. • Step Button Push this button to cycle through all the Mini-trip functions. To Reset The Display Pressing and releasing the Reset button once will clear the resettable function currently being displayed. The resettable function is average fuel economy. Reset will only occur if the resettable function is currently being displayed.
PAGE 187
UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE RAH—AM & FM STEREO RADIO WITH CD PLAYER AND CD/DVD CHANGER CONTROLS NOTE: The radio sales code is located on the lower left side of your radio faceplate. 187 Radio Operation Power/Volume Control Press the ON/VOL control to turn the radio on. Turn the volume control clockwise to increase the volume. NOTE: Power to operate the radio is supplied through the ignition switch. It must be in the ON or ACC position to operate the radio.
PAGE 188
UNDERSTANDING YOUR INSTRUMENT PANEL Toggle the TUNE button to select the following format types: Program Type Adult Hits Classical Classic Rock College Country Information Jazz Foreign Language News Nostalgia Oldies Personality Public Rhythm and Blues Radio Display Adlt Hit Classicl Cls Rock College Country Inform Jazz Language News Nostalga Oldies Persnlty Public R&B Program Type Religious Music Religious Talk Rock Soft Soft Rock Soft Rhythm and Blues Sports Talk Top 40 Weather Radio Display Rel M
PAGE 189
UNDERSTANDING YOUR INSTRUMENT PANEL 189 The radio display will flash “SEEK” and the selected PTY program type when searching for the next PTY station. If no station is found with the selected PTY program type, the radio will return to the last preset station. top of the button to seek up and the bottom to seek down. The radio will remain tuned to the new station until you make another selection. Holding the button in will bypass stations without stopping until you release it.
PAGE 190
UNDERSTANDING YOUR INSTRUMENT PANEL Tone Control The Bass and/or Treble controls sound for the desired tone. Press the AUDIO button, select Bass or TREBLE, then press SEEK + or SEEK ⫺ to increase or decrease amplification of the band. To Set The Radio Push-Button Memory When you are receiving a station that you wish to commit to push-button memory, press the SET button. SET 1 will show in the display window. Select the push-button you wish to lock onto this station and press and release that button.
PAGE 191
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Changes or modifications not expressively approved by the party responsible for compliance could void the user’s authority to operate the equipment. 191 Inserting The Compact Disc CAUTION! CD Player Operation NOTE: • The ignition switch must be in the ON or ACC position and the volume control ON before the CD player will operate.
PAGE 192
UNDERSTANDING YOUR INSTRUMENT PANEL Seek Press the top of the SEEK button for the next selection on the CD. Press the bottom of the button to return to the beginning of the current selection, or return to the beginning of the previous selection if the CD is within the first 10 seconds of the current selection. EJT — Eject Press the EJT button and the disc will unload and move to the entrance for easy removal. The unit will switch to the radio mode.
PAGE 193
UNDERSTANDING YOUR INSTRUMENT PANEL CD/DVD Changer Operation Press the MODE button to select between the CD player and the optional remote CD/DVD changer. Time Press the TIME button to change the display from elapsed CD or DVD playing time to time of day. Notes On Playing MP3 Files The radio can play MP3 files, however, acceptable MP3 file recording media and formats are limited. When writing MP3 files, pay attention to the following restrictions.
PAGE 194
UNDERSTANDING YOUR INSTRUMENT PANEL Multisession disc formats are supported by the radio. Multisession discs may contain combinations of normal CD audio tracks and computer files (including MP3 files). Discs created with an option such as ⬙keep disc open after writing⬙ are most likely multisession discs. The use of multisession for CD audio or MP3 playback may result in longer disc loading times. Supported MP3 file formats The radio will recognize only files with the *.mp3 extension as MP3 files.
PAGE 195
UNDERSTANDING YOUR INSTRUMENT PANEL Playback of MP3 files When a medium containing MP3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3 files.
PAGE 196
UNDERSTANDING YOUR INSTRUMENT PANEL RW/FF (CD Mode For MP3 Play) Press the FF side of the button to move forward through the MP3 selection. Press the RW side of the button to move back through the MP3 selection. Operating Instructions - Hands Free Phone (If Equipped) Refer to Hands Free Phone section of the Owner’s Manual. AM/FM Button (CD Mode For MP3 Play) Switches back to Radio mode.
PAGE 197
UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE REV AM & FM STEREO RADIO WITH CD PLAYER AND CD/DVD CHANGER CONTROLS NOTE: The radio sales code is located on the lower left side of your radio faceplate. 197 Radio Operation Power/Volume Control Press the ON/VOL control to turn the radio on. Turn the volume control clockwise to increase the volume. NOTE: Power to operate the radio is supplied through the ignition switch. It must be in the ON or ACC position to operate the radio.
PAGE 198
UNDERSTANDING YOUR INSTRUMENT PANEL Toggle the TUNE button to select the following format types: Program Type Adult Hits Classical Classic Rock College Country Information Jazz Foreign Language News Nostalgia Oldies Personality Public Rhythm and Blues Radio Display Adlt Hit Classicl Cls Rock College Country Inform Jazz Language News Nostalga Oldies Persnlty Public R&B Program Type Religious Music Religious Talk Rock Soft Soft Rock Soft Rhythm and Blues Sports Talk Top 40 Weather Radio Display Rel M
PAGE 199
UNDERSTANDING YOUR INSTRUMENT PANEL 199 The radio display will flash “SEEK” and the selected PTY program type when searching for the next PTY station. If no station is found with the selected PTY program type, the radio will return to the last preset station. top of the button to seek up and the bottom to seek down. The radio will remain tuned to the new station until you make another selection. Holding the button in will bypass stations without stopping until you release it.
PAGE 200
UNDERSTANDING YOUR INSTRUMENT PANEL Tone Control The Bass and/or Treble controls sound for the desired tone. Press the AUDIO button, select Bass or TREBLE, then press SEEK + or SEEK ⫺ to increase or decrease amplification of the band. To Set The Radio Push-Button Memory When you are receiving a station that you wish to commit to push-button memory, press the SET button. SET 1 will show in the display window. Select the push-button you wish to lock onto this station and press and release that button.
PAGE 201
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Changes or modifications not expressively approved by the party responsible for compliance could void the user’s authority to operate the equipment. 201 Inserting The Compact Disc CAUTION! CD Player Operation NOTE: • The ignition switch must be in the ON or ACC position and the volume control ON before the CD player will operate.
PAGE 202
UNDERSTANDING YOUR INSTRUMENT PANEL Seek Press the top of the SEEK button for the next selection on the CD. Press the bottom of the button to return to the beginning of the current selection, or return to the beginning of the previous selection if the CD is within the first 10 seconds of the current selection. EJT — Eject Press the EJT button and the disc will unload and move to the entrance for easy removal. The unit will switch to the radio mode.
PAGE 203
UNDERSTANDING YOUR INSTRUMENT PANEL CD/DVD Changer Operation Press the MODE button to select between the CD player and the optional remote CD/DVD changer. Time Press the TIME button to change the display from elapsed CD or DVD playing time to time of day. Notes On Playing MP3 Files The radio can play MP3 files, however, acceptable MP3 file recording media and formats are limited. When writing MP3 files, pay attention to the following restrictions.
PAGE 204
UNDERSTANDING YOUR INSTRUMENT PANEL Multisession disc formats are supported by the radio. Multisession discs may contain combinations of normal CD audio tracks and computer files (including MP3 files). Discs created with an option such as ⬙keep disc open after writing⬙ are most likely multisession discs. The use of multisession for CD audio or MP3 playback may result in longer disc loading times. Supported MP3 file formats The radio will recognize only files with the *.mp3 extension as MP3 files.
PAGE 205
UNDERSTANDING YOUR INSTRUMENT PANEL Playback of MP3 files When a medium containing MP3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3 files.
PAGE 206
UNDERSTANDING YOUR INSTRUMENT PANEL RW/FF (CD Mode For MP3 Play) Press the FF side of the button to move forward through the MP3 selection. Press the RW side of the button to move back through the MP3 selection. Operating Instructions - Hands Free Phone (If Equipped) Refer to Hands Free Phone section of the Owner’s Manual. AM/FM Button (CD Mode For MP3 Play) Switches back to Radio mode.
PAGE 207
UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE RBP—AM & FM STEREO RADIO WITH CASSETTE TAPE PLAYER, CD PLAYER, AND OPTIONAL CD/DVD CHANGER CONTROLS NOTE: The radio sales code is located on the lower left side of your radio faceplate. 207 Radio Operation Power/Volume Control Press the ON/VOL control to turn the radio on. Turn the volume control to the right to increase the volume. NOTE: Power to operate the radio is supplied through the ignition switch.
PAGE 208
UNDERSTANDING YOUR INSTRUMENT PANEL Toggle the PTY button to select the following format types: Program Type Adult Hits Classical Classic Rock College Country Information Jazz Foreign Language News Nostalgia Oldies Personality Public Rhythm and Blues Radio Display Adlt Hit Classicl Cls Rock College Country Inform Jazz Language News Nostalga Oldies Persnlty Public R&B Program Type Religious Music Religious Talk Rock Soft Soft Rock Soft Rhythm and Blues Sports Talk Top 40 Weather Radio Display Rel Mu
PAGE 209
UNDERSTANDING YOUR INSTRUMENT PANEL The radio display will flash “SEEK” and the selected PTY program type when searching for the next PTY station. If no station is found with the selected PTY program type, the radio will return to the last preset station. If a preset button is activated while in the PTY (Program Type) mode, the PTY mode will be exited and the radio will tune to the preset station. Pressing PTY, then SCAN will scan the FM Band and stop at all RDS stations that broadcast the station type.
PAGE 210
UNDERSTANDING YOUR INSTRUMENT PANEL Fade The Fade control provides for balance between the front and rear speakers. Press the FADE button in and it will pop out. Adjust the balance and push the button back in. Tone Control The tone controls affect the BASS and TREBLE frequency bands. Each is controlled by a slider control with a detent at the mid position. Moving a control up or down increases or decreases amplification of the band. The mid position provides a balanced output.
PAGE 211
UNDERSTANDING YOUR INSTRUMENT PANEL To set the clock, use a ballpoint pen or similar object to press the hour (H) or minute (M) buttons on the radio, The time setting will increase each time you press the button. Press any other button to exit from the clock setting mode. General Information This radio complies with Part 15 of FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following conditions: 1. This device may not cause harmful interference, 2.
PAGE 212
UNDERSTANDING YOUR INSTRUMENT PANEL Seek Press the SEEK button up for the next selection on the tape and down to return to the beginning of the current selection. Press the SEEK button up or down to move the track number to skip forward or backward 1 to 7 selections. Press the SEEK button once to move 1 selection, twice to move 2 selections, etc. the display will show the total number of times the SEEK button was pushed. The SEEK function will be cancelled by pressing either the FF/RW or AM/FM button.
PAGE 213
UNDERSTANDING YOUR INSTRUMENT PANEL Pinch Roller Release If ignition power or the radio ON/OFF switch are turned off, the pinch roller will automatically retract to protect the tape from any damage. When power is restored to the tape player, the pinch roller will automatically reengage and the tape will resume play. Dolby Noise Reduction The Dolby Noise Reduction System* is on whenever the tape player is on, but may be switched on/off.
PAGE 214
UNDERSTANDING YOUR INSTRUMENT PANEL Seek Press the top of the SEEK button for the next selection on the CD. Press the bottom of the button to return to the beginning of the current selection, or return to the beginning of the previous selection if the CD is within the first second of the current selection. Scan Press the SCAN button to play 10 seconds of each selection. Press the SCAN button a second time to cancel this feature.
PAGE 215
UNDERSTANDING YOUR INSTRUMENT PANEL To select Satellite Radio (if equipped), press the MODE button until the word SIRIUS™ appears. The following will be displayed in this order: After three seconds, the current channel name and number will be displayed for five seconds. The current program type and channel number will then be displayed for five seconds. The current channel name and number will then be displayed until an action occurs. A CD or tape may remain in the player while in the Satellite Radio mode.
PAGE 216
UNDERSTANDING YOUR INSTRUMENT PANEL Disc Down/Program Button 5 Press the DISC (button 5) button to play the previous disc. Seek Press the top of the SEEK button for the next selection on the CD. Press the bottom of the button to return to the beginning of the current selection, or return to the beginning of the previous selection if the CD is within the first second of the current selection. Time Press the TIME button to switch between time of day and CD track time.
PAGE 217
UNDERSTANDING YOUR INSTRUMENT PANEL Remote Control Remote Control Buttons 1. Headphone Transmitter 2. Menu Up/Next Track/Chapter 3. Menu Left/Fast Rewind 4. Return 5. Setup 6. Pause/Play 7. Mute 8. Display 9. Mode 10. Program Down - Previous Disc 11. Program Up - Next Disc 12. Slow 13. Stop 14. Menu 15. Menu Down/Previous Track/Chapter 16.
PAGE 218
UNDERSTANDING YOUR INSTRUMENT PANEL Remote Control Buttons 17. Enter 18. Light Headphone Transmitter Button (1) The headphone transmitter button on the remote control and the power button on the headphones must be turned ON before sound can be heard from the headphones. On some radios the headphone symbol will flash for approximately 5 seconds in the radio display, indicating the headphones are in use. ARROW Buttons (2, 3, 15, 16) These arrow buttons only function in CD/ DVD mode.
PAGE 219
UNDERSTANDING YOUR INSTRUMENT PANEL 219 PAUSE/PLAY Button (6) This button only functions in DVD video mode. Press this button once to pause the video, press a second time to play the video. PROG UP/DOWN Buttons (10, 11) PROG UP selects the next disc loaded in the changer. PROG DOWN selects the previous disc loaded in the changer. MUTE Button (7) No function. SLOW Button (12) This button only functions in DVD video mode. Press this button to advance the video.
PAGE 220
UNDERSTANDING YOUR INSTRUMENT PANEL NEXT/PREV Buttons (2, 15) Press the up arrow or the NEXT button for the next chapter or track on the disc. Press the down arrow or PREV button to return to the beginning of the current chapter or track. Press the down arrow or PREV button twice within two seconds to return to the previous chapter or track. Each press of the NEXT/PREV button up or down will toggle through the chapters or tracks.
PAGE 221
UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions — Video Screen Push up on the release button to lower the video screen. 221 1. Screen Width Button Changes the width of the screen picture. 2. Enter Button This button will enter the selection from the on-screen menu.
PAGE 222
UNDERSTANDING YOUR INSTRUMENT PANEL 3. Brightness Button Changes the brightness of the screen picture. Operating Instructions — Headphones Rear Headphones 1. Power Button 2. Volume Control Screen Button 3.
PAGE 223
UNDERSTANDING YOUR INSTRUMENT PANEL 223 Power Button Pressing the power button will turn the headphones ON/OFF. An indicator light will illuminate on the headphone earpiece to indicate the headphones are ON. NOTE: • The headphones will turn off automatically in approximately 3 minutes if they lose the signal form the system or when the radio or rear audio/video system is turned off. Volume Control Rotate the volume control to adjust the volume to the desired listening level.
PAGE 224
UNDERSTANDING YOUR INSTRUMENT PANEL General Information This device complies with part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) This device must accept any interference received, including interference that may cause undesired operation. If you do not hear sound coming from the headphones, check for the following conditions: 1. Rear Seat Audio/Video System and headphones are on.
PAGE 225
UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions — Video Games/Camcorders A video game unit or camcorder can be connected to the rear audio/video system. Connect the cables to the RCA jacks located on the front of the CD/DVD changer. NOTE: To operate a video game unit a DC to AC adapter may be required, plug the adapter into any power outlet. Follow the manufactures instructions for the correct colors when connecting the RCA cables.
PAGE 226
UNDERSTANDING YOUR INSTRUMENT PANEL Electronic Serial Number/Sirius Identification Number (ENS/SID) The Electronic Serial Number/Sirius Identification Number is needed to activate your Sirius Satellite Radio system. To access the ESN/SID, refer to the following steps: ESN/SID Access With RBB, REV and RBK Radios With the ignition switch in the ACCESSORY position and the radio OFF, press the Tape Eject or CD Eject (depending on the radio type) and Time buttons simultaneously for 3 seconds.
PAGE 227
UNDERSTANDING YOUR INSTRUMENT PANEL Selecting Satellite Mode in RBP, RBU, RAZ, RB1 and RBQ Radios Press the MODE button repeatedly until the word ⬙SIRIUS⬙ appears in the display. These radios will also display the following: • After 3 seconds, the current channel name and channel number will be displayed for 5 seconds. • The current program type and channel number will then be displayed for 5 seconds. • The current channel number will then be displayed until an action occurs.
PAGE 228
UNDERSTANDING YOUR INSTRUMENT PANEL Storing and Selecting Pre-Set Channels In addition to the 10 AM and 10 FM pre-set stations, you may also commit 10 satellite stations to push button memory. These satellite channel pre-set stations will not erase any AM or FM pre-set memory stations. Follow the memory pre-set procedures that apply to your radio. Using the PTY (Program Type) Button (If Equipped) Follow the PTY button instructions that apply to your radio.
PAGE 229
UNDERSTANDING YOUR INSTRUMENT PANEL Reception Quality Satellite reception may be interrupted due to one of the following reasons. • The vehicle is parked in an underground parking structure or under a physical obstacle. • Dense tree coverage may interrupt reception in the form of short audio mutes. • Driving under wide bridges or along tall buildings can cause intermittent reception. • Placing objects over or too close to the antenna can cause signal blockage.
PAGE 230
UNDERSTANDING YOUR INSTRUMENT PANEL The following describes the left hand rocker switch operation in each mode: If you press the switch up or down twice it plays the second selection, three times, it will play the third, etc. Radio Operation Pressing the top of the switch will SEEK up for the next listenable station and pressing the bottom of the switch will SEEK down for the next listenable station. The button in the center of the left hand switch has no function in this mode.
PAGE 231
UNDERSTANDING YOUR INSTRUMENT PANEL RADIO GENERAL INFORMATION Radio Broadcast Signals Your new radio will provide excellent reception under most operating conditions. Like any system, however, car radios have performance limitations, due to mobile operation and natural phenomena, which might lead you to believe your sound system is malfunctioning.
PAGE 232
UNDERSTANDING YOUR INSTRUMENT PANEL remain active for up to 45 seconds after the ignition switch has been turned off. Opening a vehicle front door will cancel this feature. 5. A loose tape should be corrected before use. To rewind a loose tape, insert the eraser end of a pencil into the tape drive gear and twist the pencil in the required directions.
PAGE 233
UNDERSTANDING YOUR INSTRUMENT PANEL CD/DVD DISC MAINTENANCE To keep the CD/DVD discs in good condition, take the following precautions: 1. Handle the disc by its edge; avoid touching the surface. 2. If the disc is stained, clean the surface with a soft cloth, wiping from center to edge. 3. Do not apply paper, paper CD labels, or tape to the disc; avoid scratching the disc.
PAGE 234
UNDERSTANDING YOUR INSTRUMENT PANEL The navigation DVD unit is located in the underfloor storage compartment in the rear cargo area. A single disc containing map information for the entire United States and parts of Canada is stored in the DVD unit. Updated DVD’s are available from your authorized dealer. To replace the navigation map DVD lift the storage bin cover and liner in the rear cargo area, press the eject button and the disc will eject.
PAGE 235
UNDERSTANDING YOUR INSTRUMENT PANEL Manual Air Conditioning and Heating System 235 second time the indicator light turns off, the blower will turn off and the system will be positioned in the recirculation mode. Blower Control The Blower controls the amount of air delivered to the passenger compartment. There are four blower speeds. The fan speed increases as you move the control clockwise.
PAGE 236
UNDERSTANDING YOUR INSTRUMENT PANEL Dual Zone Temperature Control — If Equipped With the Dual Zone Temperature Control System, each front seat occupant can independently control the temperature of air coming from the outlets on their side of the vehicle. Mode Control The mode control allows you to choose from several patterns of air distribution. NOTE: To improve your selection choices, the system allows you to operate at intermediate positions between the major modes.
PAGE 237
UNDERSTANDING YOUR INSTRUMENT PANEL 237 Air comes from the outlets in the instrument panel. Each of these outlets can be individually adjusted to direct the flow of air. Moving the air vane knob on the center outlets down, will close off the air flow from the center outlets. The thumbwheel next to the outboard outlets can be rotated to regulate or shut off the air flow from these outlets.
PAGE 238
UNDERSTANDING YOUR INSTRUMENT PANEL Air comes from both the instrument panel outlets, floor outlets and defrost. A slight amount of air is also directed through the side window demister outlets. Bi-Level Mode NOTE: In many temperature lever positions, the bilevel mode is designed to provide cooler air out of the panel outlets and warmer air from the floor outlets.
PAGE 239
UNDERSTANDING YOUR INSTRUMENT PANEL Floor Mode 239 Mix Mode 4 Floor Outlets Mix Outlets Air comes from the floor outlets. A slight amount of air is directed through the defrost and side window demister outlets. Air comes from the floor, defrost and side window demist outlets. This mode works best in cold or snowy conditions. It allows you to stay comfortable while keeping the windshield clear.
PAGE 240
UNDERSTANDING YOUR INSTRUMENT PANEL Defrost modes are selected. This is done to assist in drying the air and it will help in keeping the windows from fogging. Defrost Mode Manual Air Conditioning Operation To turn on the air conditioning, set the front blower control to any speed and press the A/C button which is located next to the recirculation button. An indicator light on the A/C button shows that the air conditioning is on.
PAGE 241
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: • The compressor will not engage until the engine has been running for a few seconds. • If your air conditioning performance seems lower than expected, check the A/C air filter (ATC equipped vehicles only) and the front of the A/C condenser for an accumulation of dirt or insects. The A/C condenser is located in front of the radiator. The A/C air filter is located under the instrument panel on the passenger side.
PAGE 242
UNDERSTANDING YOUR INSTRUMENT PANEL • If the recirculation button is pressed while in the Mix or Defrost mode, the indicator light in the recirculation button will flash 3 times indicating that recirculation is not allowed. • Turn the ignition switch to the OFF position. A/C Recirculation Programming The recirculation control is programmed to cancel the recirculation mode when the ignition key is turned OFF and will reset to outside air mode when the ignition key is turned ON.
PAGE 243
UNDERSTANDING YOUR INSTRUMENT PANEL Dual-Zone Automatic Temperature Control The Dual Zone Automatic Temperature Control (ATC) System automatically maintains the interior comfort level desired by the driver and front seat passenger. This is accomplished by using two infrared sensors located in the center of the instrument panel. The two infrared sensors independently measure the surface temperature of the driver and front seat passenger.
PAGE 244
UNDERSTANDING YOUR INSTRUMENT PANEL temperature you would like the system to maintain. When the system is set to your comfort level, it is not necessary to change the settings. You will experience the greatest efficiency by allowing the system to function automatically. The system will operate fully automatically in either ⬙AUTO HI⬙ or ⬙AUTO LO⬙. The ⬙AUTO LO⬙ setting will limit the maximum fan speed and should be used when more quiet operation is desired.
PAGE 245
UNDERSTANDING YOUR INSTRUMENT PANEL This feature may be enabled using the following procedure: • Press and hold the Heated Rear Window and Auto HI buttons for 5 seconds. • The “DELAY” symbol will flash to indicate that the feature as been enabled. Power Button This button turns the entire system ON/OFF. When the system is turned on it will return to the previous settings.
PAGE 246
UNDERSTANDING YOUR INSTRUMENT PANEL The front blower control can be set to any fixed blower speed by pressing the rocker switch up or down. This allows the front occupants to control the volume of air circulated in the vehicle and cancel the auto mode. The fan will now operate at a fixed speed until additional speeds are selected or until either the ⬙AUTO HI⬙ or ⬙AUTO LO⬙ buttons are pressed. The system will continue to automatically adjust air temperature and airflow distribution.
PAGE 247
UNDERSTANDING YOUR INSTRUMENT PANEL Bi-Level Mode 247 Air comes from both the instrument panel outlets and floor outlets. A slight amount of air is also directed through the defrost and side window demister outlets. NOTE: In many temperature positions, the bi-level mode is designed to provide cooler air out of the panel outlets and warmer air from the floor outlets.
PAGE 248
UNDERSTANDING YOUR INSTRUMENT PANEL Floor Mode Mix Mode Floor Outlets Mix Outlets Air comes from the floor outlets. A slight amount of air is directed through the defrost and side window demister outlets. Air comes from the floor, defrost and side window demist outlets. This mode is not used when operating in either ⬙AUTO HI⬙ or ⬙AUTO LO⬙. This mode should be used when airflow to the floor and windshield is desired.
PAGE 249
UNDERSTANDING YOUR INSTRUMENT PANEL Defrost Mode 249 windshield or side glass starts to impair visibility, press the front blower button and increase the fan speed to maximum. NOTE: While operating in ⬙AUTO HI⬙ or ⬙AUTO LO⬙, the system will not automatically sense the presence fog, mist, or ice on the windshield. The defrost button must be pressed to clear the windshield and side glass. Defrost Outlets Depress the “A/C” button to turn on and off the air conditioning during manual operation only.
PAGE 250
UNDERSTANDING YOUR INSTRUMENT PANEL windshield or side glass starts to impair visibility, press the front blower button and increase the fan speed to maximum. Recirculation Control When the outside air contains smoke, odors, high humidity, or if rapid cooling is desired you may wish to recirculate interior air by pressing the recirculation button. The recirculation mode should only be used temporarily. The recirculate symbol will illuminate in the display when this button is selected.
PAGE 251
UNDERSTANDING YOUR INSTRUMENT PANEL • While holding the recirculation button, turn the ignition switch to the “RUN” position. • Continue holding the recirculation button for 4 seconds, then release. The recirculation control is now programmed so that the recirculation mode will not reset to the outside air mode when the engine is restarted. The recirculation programming can be changed back by repeating this procedure. Rear Fan Operation To operate the rear fan, press the ⬙REAR⬙ button.
PAGE 252
UNDERSTANDING YOUR INSTRUMENT PANEL glycol antifreeze coolant in water is recommended. Refer to section 7, Maintenance Procedures, of this manual for proper coolant selection. Winter Operation To insure the best possible heater and defroster performance, make sure the engine cooling system is functioning properly and the proper amount, type, and concentration of coolant is used. Refer to section 7, Maintenance Procedures, of this manual for proper coolant selection.
PAGE 253
UNDERSTANDING YOUR INSTRUMENT PANEL A/C Air Filter — If Equipped On vehicles equipped with Automatic Temperature Control (ATC), the climate control system filters out dust, pollen and some odors from the air. Strong odors can not be totally filtered out. Refer to section 7 “Air Conditioning” for filter replacement instructions. Outside Temperature Display The outside temperature can be shown in the ATC display by pressing the ⬙OUTSIDE TEMP⬙ button.
PAGE 254
PAGE 255
STARTING AND OPERATING CONTENTS 䡵 Starting Procedures . . . . . . . . . . . . . . . . . . . . . 258 ▫ AutoStick Operation . . . . . . . . . . . . . . . . . . . 264 ▫ Normal Starting . . . . . . . . . . . . . . . . . . . . . . 258 ▫ AutoStick General Information . . . . . . . . . . . . 265 䡵 Engine Block Heater — If Equipped . . . . . . . . . 260 䡵 All Wheel Drive — If Equipped . . . . . . . . . . . . 266 䡵 Automatic Transmission . . . . . . . . . . . . . . . . . . 261 䡵 Parking Brake . . . . . . . .
PAGE 256
STARTING AND OPERATING ▫ Tire Markings . . . . . . . . . . . . . . . . . . . . . . . . 274 ▫ Alignment And Balance . . . . . . . . . . . . . . . . . 290 ▫ Tire Identification Number (TIN) . . . . . . . . . . 277 䡵 All Wheel Drive (AWD) — If Equipped . . . . . . . 291 ▫ Tire Loading And Tire Pressure . . . . . . . . . . . 278 䡵 Tire Pressure Monitor System — If Equipped . . . 291 䡵 Tires—General Information . . . . . . . . . . . . . . . . 282 ▫ 1,2,3, Or 4 Tire(s) Low Pressure . . . . . . . . .
PAGE 257
STARTING AND OPERATING 257 ▫ Materials Added To Fuel . . . . . . . . . . . . . . . . 298 䡵 Trailer Towing . . . . . . . . . . . . . . . . . . . . . . . . . 304 ▫ Fuel System Cautions . . . . . . . . . . . . . . . . . . 298 ▫ Common Towing Definitions . . . . . . . . . . . . . 305 ▫ Carbon Monoxide Warnings . . . . . . . . . . . . . . 299 ▫ Trailer Hitch Classification . . . . . . . . . . . . . . . 307 䡵 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 258
STARTING AND OPERATING STARTING PROCEDURES CAUTION! Long periods of engine idling, especially at high engine speeds, can cause excessive exhaust temperatures which can damage your vehicle. Do not leave your vehicle unattended with the engine running. WARNING! Do not leave animals or children inside parked vehicles in hot weather; interior heat build up may cause serious injury or death. The gear selector must be in the NEUTRAL or PARK position before you can start the engine.
PAGE 259
STARTING AND OPERATING WARNING! • Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transmission cannot be started this way. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle. If the vehicle has a discharged battery, booster cables may be used to obtain a start from a booster battery or the battery in another vehicle. This type of start can be dangerous if done improperly.
PAGE 260
STARTING AND OPERATING If the engine has been flooded, it may start to run, but not have enough power to continue running when the key is released. If this occurs, continue cranking up to 15 seconds with the accelerator pedal pushed all the way to the floor. Release the accelerator pedal and the key once the engine is running smoothly. Do not overspeed engine.
PAGE 261
STARTING AND OPERATING AUTOMATIC TRANSMISSION CAUTION! Damage to the transmission may occur if the following precautions are not observed: • Shift into PARK only after the vehicle has come to a complete stop. • Shift into or out of REVERSE only after the vehicle has come to a complete stop and the engine is at idle speed. • Do not shift from REVERSE, PARK, or NEUTRAL into any forward gear when the engine is above idle speed.
PAGE 262
STARTING AND OPERATING Automatic Transmission Ignition Interlock System This system prevents the key from being removed unless the shift lever is in PARK. It also prevents shifting out of PARK unless the key is in the ACCESSORY or ON position. NOTE: If a malfunction occurs, the system will trap the key in the ignition cylinder to warn you that this safety feature is inoperable. The engine can be started and stopped but the key cannot be removed until you obtain service.
PAGE 263
STARTING AND OPERATING possible convenience. Your dealer has diagnostic equipment to determine if the problem could recur. If the transmission cannot be reset, dealer service is required. Gear Ranges DO NOT race the engine when shifting from PARK or NEUTRAL positions into another gear range. The override can be activated by pressing the pinkcolored tab, which can be accessed through the lower right corner of the shifter bezel ring.
PAGE 264
STARTING AND OPERATING “R” Reverse Shift into this range only after the vehicle has come to a complete stop. “N” Neutral Engine may be started in this range. “D” Overdrive To be used for most city and highway driving, it provides smoothest upshifts and downshifts and best fuel economy. When frequent transmission shifting occurs while using the “D” Overdrive position, such as when operating the vehicle under heavy loading conditions, (i.e.
PAGE 265
STARTING AND OPERATING 265 You can shift in or out of the AutoStick mode at any time without taking your foot off the accelerator pedal. If you choose the Overdrive mode, the transmission will operate automatically; shifting between the four available gears. When you wish to engage AutoStick, simply move the shift lever to the AUTOSTICK position. The transmission will remain in the current gear until an upshift or downshift is chosen. • You can start out in first, second, or third gear.
PAGE 266
STARTING AND OPERATING • If the system detects a problem it will disable the AutoStick mode and the transmission will return to the automatic mode until the problem is corrected. ALL WHEEL DRIVE — IF EQUIPPED This feature provides full time, on-demand, All Wheel Drive (AWD). The system is automatic with no driver inputs or additional driving skills required. Under normal driving conditions, the front wheels provide most of the traction.
PAGE 267
STARTING AND OPERATING Before leaving the vehicle, make sure that the parking brake is fully applied and place the gear selector in the Park position. To release the parking brake, pull out on the parking brake release located on the left side of the instrument panel. 267 When parking on a hill, it is important to set the parking brake before placing the gear selector in Park, otherwise the load on the transmission locking mechanism may make it difficult to move the selector out of park.
PAGE 268
STARTING AND OPERATING WARNING! • Leaving children in a vehicle unattended is dangerous for a number of reasons. A child or others could be injured. Children should be warned not to touch the parking brake, brake pedal or the gear selector lever. Don’t leave the keys in the ignition. A child could operate power windows, other controls, or move the vehicle. • Be sure the parking brake is fully disengaged before driving: failure to do so can lead to brake failure, and an accident.
PAGE 269
STARTING AND OPERATING Anti-Lock Brake System The Anti-Lock Brake System provides increased vehicle stability and brake performance under most braking conditions. The system automatically “pumps” the brakes during severe braking conditions to prevent wheel lock-up. WARNING! Pumping of the Anti-Lock Brakes will diminish their effectiveness and may lead to an accident. Pumping makes the stopping distance longer. Just press firmly on your brake pedal when you need to slow down or stop.
PAGE 270
STARTING AND OPERATING The ABS light monitors the Anti-Lock Brake System. The light will come on when the ignition switch is turned to the ON position and may stay on for as long as four seconds. If the ABS light remains on or comes on while driving, it indicates that the Anti-Lock portion of the brake system is not functioning and that service is required. However, the conventional brake system will continue to operate normally if the BRAKE warning light is not on.
PAGE 271
STARTING AND OPERATING • and a slight drop or fall away of the brake pedal at the end of the stop. These are all normal characteristics of ABS. WARNING! The Anti-Lock Brake System contains sophisticated electronic equipment that may be susceptible to interference caused by improperly installed or high output radio transmitting equipment. This interference can cause possible loss of anti-lock braking capability. Installation of such equipment should be performed by qualified professionals.
PAGE 272
STARTING AND OPERATING WARNING! Continued operation with reduced power steering assist could pose a safety risk to yourself and others. Service should be obtained as soon as possible. TRACTION CONTROL — IF EQUIPPED The Traction Control System reduces wheel slip and maintains traction at the driving (front) wheels. The system reduces wheel slip by engaging the brake on the wheel that is losing traction (spinning). The system will operate at speeds below 35 mph (56 km/h).
PAGE 273
STARTING AND OPERATING 273 NOTE: • The Traction Control system will make buzzing or clicking sounds when in operation. • Extended heavy use of Traction Control may cause the system to deactivate and turn on the traction control indicator located in the instrument cluster. This is to prevent overheating of the brake system and is a normal condition. The system will remain disabled for about 4 minutes until the brakes have cooled.
PAGE 274
STARTING AND OPERATING TIRE SAFETY INFORMATION Tire Markings • European Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter ⬙P⬙ is absent from this tire size designation. Example: 215/65R15 96H • LT (Light Truck)-Metric tire sizing is based on U.S. design standards.
PAGE 275
STARTING AND OPERATING 275 Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ⴖ....blank....ⴖ = Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary Spare tire 31 = Overall Diameter in Inches (in) 215 = Section Width in Millimeters (mm) 65 = Aspect Ratio in Percent (%) —Ratio of section height to section width of tire. 10.
PAGE 276
STARTING AND OPERATING EXAMPLE: Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry. H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions. —The maximum speed corresponding to the Speed Symbol should only be achieved under specified operating conditions. (i.e. tire pressure, vehicle loading, road conditions and posted speed limits).
PAGE 277
STARTING AND OPERATING Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire however the date code may only be on one side. Tires with white sidewalls will have the full TIN including date code 277 located on the white sidewall side of the tire. Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the outboard side then you will find it on the inboard side of the tire.
PAGE 278
STARTING AND OPERATING Tire Loading and Tire Pressure Tire and Loading Information Placard Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on either the face of the driver’s door or the driver’s side “B” pillar.
PAGE 279
STARTING AND OPERATING 3) the tire size designed for your vehicle 4) the cold tire inflation pressures for the front, rear and spare tires. Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the “Tire and Loading Information” placard and in the “Vehicle Loading” section of this manual.
PAGE 280
STARTING AND OPERATING 4. The resulting figure equals the available amount of cargo and luggage load capacity. For example, if “XXX” amount equals 1400 lbs. and there will be five 150 lb. passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lb. (since 5 x 150 = 750, and 1400 – 750 = 650 lb.) 5. Determine the combined weight of luggage and cargo being loaded on the vehicle.
PAGE 281
STARTING AND OPERATING 281 5
PAGE 282
STARTING AND OPERATING WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES—GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle. Three primary areas are affected by improper tire pressure: 1.
PAGE 283
STARTING AND OPERATING 283 2. Economy— Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Underinflation also increases tire rolling resistance and results in higher fuel consumption. 3. Ride Comfort and Vehicle Stability— Proper tire inflation contributes to a comfortable ride. Overinflation produces a jarring and uncomfortable ride.
PAGE 284
STARTING AND OPERATING CAUTION! After inspecting or adjusting the tire pressure, always reinstall the valve stem cap–if equipped. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressures specified on the placard are always “cold tire inflation pressure”. Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or driven less than 1 mile (1 km) after a 3 hour period.
PAGE 285
STARTING AND OPERATING loading may be required for high speed vehicle operation. Refer to original equipment or an authorized tire dealer for recommended safe operating speeds, loading and cold tire inflation pressures. WARNING! High speed driving with your vehicle under maximum load is dangerous. The added strain on your tires could cause them to fail. You could have a serious accident. Don’t drive a vehicle loaded to the maximum capacity at continuous speeds above 75 mph (120 km/h).
PAGE 286
STARTING AND OPERATING Compact Spare Tire — If Equipped The compact spare is for temporary emergency use with radial tires. It is engineered to be used on your style vehicle only. Since this tire has limited tread life, the original tire should be repaired (or replaced) and reinstalled at the first opportunity. Do not install a wheel cover or attempt to mount a conventional tire on the compact spare wheel, since the wheel is designed specifically for the compact spare.
PAGE 287
STARTING AND OPERATING Limited Use Spare — If Equipped The limited use spare tire is for temporary emergency use on your vehicle. This tire is identified by a limited use spare tire warning label located on the limited use spare tire and wheel assembly. This tire may look like the original equipped tire on the front or rear axle of your vehicle, but it is not. Installation of this limited use spare tire affects vehicle handling.
PAGE 288
STARTING AND OPERATING WARNING! Fast spinning tires can be dangerous. Forces generated by excessive wheel speeds may cause tire damage or failure. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 35 mph (55 km/h) when you are stuck. And don’t let anyone near a spinning wheel, no matter what the speed. Tread Wear Indicators Tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced.
PAGE 289
STARTING AND OPERATING 289 Life of Tire The service life of a tire is dependent upon varying factors including but not limited to: Keep unmounted tires in a cool, dry place with as little exposure to light as possible. Protect tires from contact with oil, grease and gasoline. • Driving style Replacement Tires The tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for wear and correct cold tire inflation pressure.
PAGE 290
STARTING AND OPERATING WARNING! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle. This can cause unpredictable handling and stress to steering and suspension components. You could lose control and have an accident resulting in serious injury or death.
PAGE 291
STARTING AND OPERATING Improper alignment will not cause vehicle vibration. Vibration may be a result of tire and wheel out-ofbalance. Proper balancing will reduce vibration and avoid tire cupping and spotty wear. ALL WHEEL DRIVE (AWD) — IF EQUIPPED CAUTION! All Wheel Drive (AWD) vehicles must have the same size and type tires on all wheel positions. Unequal tire sizes must not be used. Unequal tire size may cause failure of the power transfer unit and/or the viscous coupling.
PAGE 292
STARTING AND OPERATING 1,2,3, OR 4 TIRE(S) LOW PRESSURE Low tire pressure levels of 26 psi [1.79 bars] (179 kPa) or less detected in one or more tires. Inspect all tires for proper inflation pressure, once the proper tire pressure has been set, the TPMS system warning will reset automatically when the vehicle has been driven for at least 2 minutes at or above 20 mph (32 km/h). CHECK TPM SYSTEM The Tire Pressure Monitor System (TPMS) system requires service.
PAGE 293
STARTING AND OPERATING • The TPMS system is not intended to replace normal tire care and maintenance, nor to provide warning of a tire failure or condition. • The TPMS system should not be used as a tire pressure gauge while adjusting your tire pressure. CAUTION! After inspecting or adjusting the tire pressure always reinstall the valve stem cap, if equipped. This will prevent moisture and dirt from entering the valve stem, which could damage the wheel rim sensor.
PAGE 294
STARTING AND OPERATING TIRE CHAINS Use only compact chains, or other traction aids that meet SAE type “Class S” specifications. Chains must be the proper size for the vehicle, as recommended by the chain manufacturer. NOTE: Do not use tire chains on a compact spare tire. CAUTION! To avoid damage to your vehicle or tires, observe the following precautions: • Because of restricted chain clearance between tires and other suspension components, it is important that only chains in good condition are used.
PAGE 295
STARTING AND OPERATING NOTE: In order to avoid damage to tires, chains, and your vehicle do not drive for a prolonged period of time on dry pavement. Observe the tire chain manufacturer’s instructions on method of installation, operating speed, and conditions for usage. Always use the lower suggested operating speed if both the chain manufacturer and vehicle manufacture suggest a maximum speed. This notice applies to all chain traction devices, including link and cable (radial) chains.
PAGE 296
STARTING AND OPERATING Follow the recommended tire rotation frequency for your type of driving found in the “Maintenance Schedules” Section of this manual. More frequent rotation is permissible if desired. The reasons for any rapid or unusual wear should be corrected prior to rotation being performed. The suggested rotation method is the “forward-cross” shown in the following diagram.
PAGE 297
STARTING AND OPERATING 297 Over 40 automobile manufacturers around the world have issued and endorsed consistent gasoline specifications (the World Wide Fuel Charter, WWFC) to define fuel properties necessary to deliver enhanced emissions, engine performance, and durability for your vehicle. The manufacturer recommends the use of gasolines that meet the WWFC specifications if they are available.
PAGE 298
STARTING AND OPERATING MMT In Gasoline MMT is a manganese containing metallic additive that is blended into some gasoline to increase the octane number. Gasolines blended with MMT offer no performance advantage beyond gasolines of the same octane number without MMT. Gasolines blended with MMT have shown to reduce spark plug life and reduce emission system performance in some vehicles. The manufacturer recommends using gasolines without MMT.
PAGE 299
STARTING AND OPERATING • An out-of-tune engine, or certain fuel or ignition malfunctions, can cause the catalytic converter to overheat. If you notice a pungent burning odor or some light smoke, your engine may be out of tune or malfunctioning and may require immediate service. Contact your dealer for service assistance. • The use of fuel additives which are now being sold as octane enhancers is not recommended. Most of these products contain high concentrations of methanol.
PAGE 300
STARTING AND OPERATING • Guard against carbon monoxide with proper maintenance. Have the exhaust system inspected every time the vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side windows fully open. • Keep the liftgate closed when driving your vehicle to prevent carbon monoxide and other poisonous exhaust gases from entering the vehicle.
PAGE 301
STARTING AND OPERATING NOTE: • Tighten the fuel filler cap until you hear a “clicking” sound. This is an indication that the fuel filler cap is properly tightened. If the vehicle diagnostic system determines that the fuel filler cap is loose, improperly installed, or damaged, GASCAP will be displayed in the instrument cluster odometer. Tighten the fuel filler cap properly and press the odometer reset button to turn the GASCAP message off.
PAGE 302
STARTING AND OPERATING VEHICLE LOADING The load carrying capacity of your vehicle is shown in the charts that follow. This information should be used for passenger and luggage loading as indicated. • Vehicle Identification Number (VIN) If the seatbacks are folded for carrying cargo, do not exceed the specified GVWR and GAWR. The bar code allows a computer scanner to read the Vehicle Identification Number (VIN).
PAGE 303
STARTING AND OPERATING WARNING! Because the front wheels drive and steer the vehicle, it is important that you do not exceed the maximum front or rear GAWR. A dangerous driving condition can result if either rating is exceeded. You could lose control of the vehicle and have an accident. Overloading The load carrying components (axle, springs, tires, wheels, etc.) of your vehicle will provide satisfactory service as long as you do not exceed the GVWR and front and rear GAWR.
PAGE 304
STARTING AND OPERATING A loaded vehicle is shown in the illustration. Note that neither the GVWR or the GAWR capacities have been exceeded. Load (Including driver, passengers and cargo) Total GAWR 223 lbs (101 kg) 2762 lbs (1253 kg) 2826 lbs (1282 kg) 890 lbs (404 kg) 2968 lbs (1346 kg) 3035 lbs (1377 kg) TRAILER TOWING In this section you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle.
PAGE 305
STARTING AND OPERATING Common Towing Definitions The following trailer towing related definitions will assist you in understanding the following information: Gross Vehicle Weight Rating (GVWR) The GVWR is the total allowable weight of your vehicle. This includes driver, passengers, cargo and tongue weight. The total load must be limited so that you do not exceed the GVWR.
PAGE 306
STARTING AND OPERATING WARNING! It is important that you do not exceed the maximum front or rear GAWR. A dangerous driving condition can result if either rating is exceeded. You could lose control of the vehicle and have an accident. Tongue Weight (TW) The downward force exerted on the hitch ball by the trailer. In most cases it should not be less than 10% or more than 15% of the trailer load. You must consider this as part of the load on your vehicle.
PAGE 307
STARTING AND OPERATING Trailer Hitch Classification Your vehicle may be factory equipped for safe towing of trailers weighing over 2,000 lbs (907 kg) with the optional Trailer Tow Prep Package. See your dealer for package content. The following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition.
PAGE 308
STARTING AND OPERATING Engine/Transmission GCWR (Gross Combined Wt. Rating) 3.5L & 3.8L Auto8,600 lbs (3900 kg) matic Frontal Area 40 SQ. FT. 8,600 lbs (3900 kg) 40 SQ. FT. 8,600 lbs (3900 kg) 40 SQ. FT. Max. GTW (Gross Trailer Wt.) Up to 2 persons & Luggage 3,500 lbs (1600 kg) 3 to 4 persons & Luggage 3,000 lbs (1360 kg) 5 to 6 persons & Luggage 1,000 lbs (454 kg) Max. Tongue Wt. 350 lbs (158 kg) 300 lbs (136 kg) 100 lbs (45 kg) Refer to local laws for maximum trailer towing speeds.
PAGE 309
STARTING AND OPERATING which will cause loss of control of the vehicle and trailer. Failure to load trailers heavier in front is the cause of many trailer accidents. Never exceed the maximum tongue weight stamped on your bumper or trailer hitch. 309 Consider the following items when computing the weight on the rear axle of the vehicle: • The tongue weight of the trailer. • The weight of any other type of cargo or equipment put in or on your vehicle. • The weight of the driver and all passengers.
PAGE 310
STARTING AND OPERATING Towing Requirements To promote proper break-in of your new vehicle drivetrain components the following guidelines are recommended: CAUTION! • Avoid towing a trailer for the first 500 miles (805 km) of vehicle operation. Doing so may damage your vehicle. • During the first 500 miles (805 km) of trailer towing, limit your speed to 50 mph (80 km/h). Perform the maintenance listed in Section 8 of this manual. When towing a trailer, never exceed the GAWR, or GCWR, ratings.
PAGE 311
STARTING AND OPERATING • Safety chains must always be used between your vehicle and trailer. Always connect the chains to the frame or hook retainers of the vehicle hitch. Cross the chains under the trailer tongue and allow enough slack for turning corners. • Vehicles with trailers should not be parked on a grade. When parking, apply the parking brake on the tow vehicle. Put the tow vehicle automatic transmission in P for Park. Always, block or ⬙chock⬙ the trailer wheels. • GCWR must not be exceeded.
PAGE 312
STARTING AND OPERATING − When replacing tires refer to the Tires–General Information section of this manual on Replacement Tires for proper tire replacement procedures. Replacing tires with a higher load carrying capacity will not increase the vehicle’s GVWR and GAWR limits. − Trailer brakes are recommended for trailers over 1,000 lbs (454 kg) and required for trailers in excess of 2,000 lbs (907 kg).
PAGE 313
STARTING AND OPERATING 313 WARNING! NOTE: Do not cut or splice wiring into the vehicles wiring harness. Do not connect trailer brakes to your vehicle’s hydraulic brake lines. It can overload your brake system and cause it to fail. You might not have brakes when you need them and could have an accident. Towing any trailer will increase your stopping distance. When towing you should allow for additional space between your vehicle and the vehicle in front of you.
PAGE 314
STARTING AND OPERATING Towing Tips — Automatic Transmission The “D” range can be selected when towing. However, if frequent shifting occurs while in this range, the “3” range should be selected. NOTE: Using the “3” range while operating the vehicle under heavy operating conditions will improve performance and extend transmission life by reducing excessive shifting and heat build up. This action will also provide better engine braking.
PAGE 315
STARTING AND OPERATING 315 Towing Tips — Electronic Speed Control (If Equipped) − Air Conditioning Turn off temporarily. − Don’t use in hilly terrain or with heavy loads. − refer to Cooling System Operating information in the Maintenance section of this manual for more information. − When using the speed control, if you experience speed drops greater than 10 mph (16 km/h), disengage until you can get back to cruising speed.
PAGE 316
PAGE 317
WHAT TO DO IN EMERGENCIES CONTENTS 䡵 Hazard Warning Flasher . . . . . . . . . . . . . . . . . . 318 ▫ Acceleration . . . . . . . . . . . . . . . . . . . . . . . . . 329 䡵 If Your Engine Overheats . . . . . . . . . . . . . . . . . 319 ▫ Traction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 329 䡵 Jacking And Tire Changing . . . . . . . . . . . . . . . . 320 䡵 Freeing A Stuck Vehicle . . . . . . . . . . . . . . . . . . 330 ▫ Jack Location . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 318
WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER The hazard flasher switch is located in the center of the instrument panel above the center air outlets. To engage the Hazard Warning Flashers, depress the switch on the instrument panel. When the Hazard Warning Switch is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency. Push the switch a second time to turn off the flashers.
PAGE 319
WHAT TO DO IN EMERGENCIES IF YOUR ENGINE OVERHEATS In any of the following situations, you can reduce the potential for overheating by taking the appropriate action. • On the highways — Slow down. • In city traffic — While stopped, put transmission in neutral, but do not increase engine idle speed. NOTE: There are steps that you can take to slow down an impending overheat condition. If your air conditioner is on, turn it off.
PAGE 320
WHAT TO DO IN EMERGENCIES WARNING! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call a service center if your vehicle overheats. If you decide to look under the hood yourself, see Section 7, Maintenance, of this manual. Follow the warnings under the Cooling System Pressure Cap paragraph. JACKING AND TIRE CHANGING WARNING! • Getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you.
PAGE 321
WHAT TO DO IN EMERGENCIES Jack Location Five Passenger Seating The jack and jack-handle are stowed in the rear storage bin located behind the second row bench seat. Pull up on the storage bin cover to access the jack and jack tools. 321 Remove the scissors jack and jack handle by rotating the small wing nut to the left.
PAGE 322
WHAT TO DO IN EMERGENCIES Six Passenger Seating The jack and jack-handle are stowed in the rear storage bin located in the rear cargo floor. Pull up on the storage bin cover and liner to access the jack and jack tools. Spare Tire Stowage Five Passenger Seating The spare tire is stowed under the rear of the vehicle by means of a cable winch mechanism. To remove or stow the spare, use the jack handle to rotate the “spare tire drive” nut.
PAGE 323
WHAT TO DO IN EMERGENCIES 323 CAUTION! The winch mechanism is designed for use with the jack handle only. Use of an air wrench or other power tools is not recommended and can damage the winch. When the spare is clear, tilt the retainer at the end of the cable and pull it through the center of the wheel. Lowering Spare Tire Spare Tire Removal Fit the jack-handle over the drive nut.
PAGE 324
WHAT TO DO IN EMERGENCIES WARNING! Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. • Turn on the Hazard Warning Flasher. • Block both the front and rear of the wheel diagonally opposite the jacking position. For example, if changing the right front tire, block the left rear wheel. • Passengers should not remain in the vehicle when the vehicle is being jacked.
PAGE 325
WHAT TO DO IN EMERGENCIES 325 location. Do not raise the vehicle until you are sure the jack is securely engaged. Never jack up the vehicle using any suspension components. 6. Raise the vehicle by turning the jack screw to the right, using the swivel wrench. Raise the vehicle only until the tire just clears the surface and enough clearance is obtained to install the spare tire. Minimum tire lift provides maximum stability. WARNING! Jack Engagement Locations 5.
PAGE 326
WHAT TO DO IN EMERGENCIES 7. Remove the wheel lug nuts, for vehicles with wheel covers, remove the cover from the wheel by hand. Do not pry the wheel cover off. Then pull the wheel off the hub. 8. Install the spare wheel, for vehicles with wheel covers, align the notch in the wheel cover with the valve stem on the wheel. Install the cover on the wheel by hand only and install the wheel lug nuts with the cone shaped end of the nut toward the wheel. Lightly tighten the lug nuts.
PAGE 327
WHAT TO DO IN EMERGENCIES • Turn the wheel so that the valve-stem is down. Slide the wheel retainer through the center of the wheel and position it properly across the wheel opening. 327 14. Check the tire pressure as soon as possible. Correct pressure as required. • For convenience in checking the spare tire inflation, stow with the valve-stem toward the rear of the vehicle.
PAGE 328
WHAT TO DO IN EMERGENCIES • Do not attempt to push or tow your vehicle to get it started. 1. Wear eye protection and remove any metal jewelry such as watch bands or bracelets that might make an inadvertent electrical contact. Vehicles equipped with an automatic transmission cannot be started this way. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle.
PAGE 329
WHAT TO DO IN EMERGENCIES 5. Connect the other cable, first to the negative terminal of the booster battery and then to the engine of the vehicle with the discharged battery. Make sure you have a good contact on the engine. 6. Start the engine in the vehicle which has the booster battery, let the engine idle a few minutes, then start the engine in the vehicle with the discharged battery. 7. When removing the jumper cables, reverse the above sequence exactly. Be careful of the moving belts and fan.
PAGE 330
WHAT TO DO IN EMERGENCIES 2. Slow down if road has standing water or puddles. 3. Replace tires when tread wear indicators first become visible. 4. Keep tires properly inflated. 5. Maintain sufficient distance between your vehicle and the vehicle in front to avoid a collision in a sudden stop. FREEING A STUCK VEHICLE If your vehicle becomes stuck in mud, sand or snow, it can often be moved by a rocking motion. Turn your steering wheel right and left to clear the area around the front wheels.
PAGE 331
WHAT TO DO IN EMERGENCIES TOWING A DISABLED VEHICLE With Ignition Key Front Wheel Drive Your vehicle may be towed under the following conditions: The gear selector must be in NEUTRAL, the distance to be traveled must not exceed 100 miles (160 km), the towing speed must not exceed 44 mph (72 km/h), and both front and rear wheels must be on the ground. Exceeding these towing limits may cause a transmission geartrain failure.
PAGE 332
WHAT TO DO IN EMERGENCIES All Transmissions CAUTION! • Do not attempt to tow this vehicle from the front with sling type towing equipment. Damage to the front fascia will result. • Always use wheel lift equipment when towing from the front. The only other approved method of towing is with a flat bed truck. • Do not tow the vehicle from the rear. Damage to the rear sheet metal, liftgate and fascia will occur.
PAGE 333
WHAT TO DO IN EMERGENCIES 333 TOWING THIS VEHICLE BEHIND ANOTHER VEHICLE WITH A TOW DOLLY The manufacturer does not recommend that you tow an All-Wheel Drive (AWD) or front wheel drive vehicle on a tow dolly. Vehicle damage may occur.
PAGE 334
PAGE 335
MAINTAINING YOUR VEHICLE CONTENTS 䡵 3.5L Engines . . . . . . . . . . . . . . . . . . . . . . . . . . 338 ▫ Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . 344 䡵 3.8L Engines . . . . . . . . . . . . . . . . . . . . . . . . . . 339 ▫ Engine Oil Filter . . . . . . . . . . . . . . . . . . . . . . 348 䡵 Onboard Diagnostic System — OBD II . . . . . . . . 340 ▫ Drive Belts — Check Condition And Tension . . 348 ▫ Loose Fuel Filler Cap Message . . . . . . . . . . . . 341 ▫ Spark Plugs . . . . .
PAGE 336
MAINTAINING YOUR VEHICLE ▫ Front & Rear Suspension Ball Joints . . . . . . . . 355 ▫ Automatic Transmission . . . . . . . . . . . . . . . . 367 ▫ Steering Shaft Seal . . . . . . . . . . . . . . . . . . . . 355 ▫ All Wheel Drive (AWD) — If Equipped . . . . . 370 ▫ Steering Linkage . . . . . . . . . . . . . . . . . . . . . . 355 ▫ Front And Rear Wheel Bearings . . . . . . . . . . . 372 ▫ Drive Shaft Universal Joints . . . . . . . . . . . . . . 355 ▫ Appearance Care And Protection From Corrosion .
PAGE 337
MAINTAINING YOUR VEHICLE ▫ Front Park/Turn Signal And Sidemarker Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 384 ▫ Front Fog Light . . . . . . . . . . . . . . . . . . . . . . 384 ▫ Rear Tail, Stop, Turn Signal, Side Marker And Back-Up Lights . . . . . . . . . . . . . . . . . . . . . . . 385 337 䡵 Fluids And Capacities . . . . . . . . . . . . . . . . . . . 386 䡵 Fluids, Lubricants And Genuine Parts . . . . . . . . 387 ▫ Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 338
MAINTAINING YOUR VEHICLE 3.5L ENGINES Engine Compartment 3.
PAGE 339
MAINTAINING YOUR VEHICLE 339 3.8L ENGINES 7 Engine Compartment 3.
PAGE 340
MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
PAGE 341
MAINTAINING YOUR VEHICLE Loose Fuel Filler Cap Message After fuel is added, the vehicle diagnostic system can determine if the fuel filler cap is loose, improperly installed, or damaged. A loose fuel filler cap message will be displayed in the instrument cluster. Tighten the gas cap until a ⬙clicking⬙ sound is heard. This is an indication that the gas cap is properly tightened. Press the odometer reset button to turn the message off.
PAGE 342
MAINTAINING YOUR VEHICLE Your vehicle has a simple ignition key actuated test which you can use prior to going to the test station. To check if your vehicle’s OBD system is ready, you must do the following: 1. Insert your ignition key into the ignition switch. 2. Turn the ignition to the ON position, but do not crank or start the engine. 3. If you crank or start the engine, you will have to start this test over. 4.
PAGE 343
MAINTAINING YOUR VEHICLE vehicle serviced before going to the I/M station. The I/M station can fail your vehicle because the MIL symbol is on with the engine running. REPLACEMENT PARTS Use of genuine Mopar威 parts for normal/scheduled maintenance and repairs is highly recommended to insure the designed performance. Damage or failures caused by the use of non-Mopar威 parts for maintenance and repairs will not be covered by the manufacturer’s warranty.
PAGE 344
MAINTAINING YOUR VEHICLE MAINTENANCE PROCEDURES The pages that follow contain the required maintenance services determined by the engineers who designed your vehicle. Besides the maintenance items for which there are fixed maintenance intervals, there are other items that should operate satisfactorily without periodic maintenance. However, if a malfunction of these items does occur, it could adversely affect the engine or vehicle performance.
PAGE 345
MAINTAINING YOUR VEHICLE 345 Change Engine Oil Road conditions and your kind of driving affects the interval at which your oil should be changed. Check the following list to see if any apply to you. • Day or night temperatures are below 32°F (0°C). • Stop and Go driving. • Extensive engine idling. • Driving in dusty conditions. • Short trips of less than 10 miles (16 km). Engine Oil Dipstick CAUTION! Overfilling or underfilling will cause oil aeration or loss of oil pressure.
PAGE 346
MAINTAINING YOUR VEHICLE NOTE: If ANY of these apply to you then change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first and follow schedule “B” of the ⬙Maintenance Schedules⬙ section of this manual. If none of these apply to you, then change your engine oil at every interval shown on schedule ⬙A⬙ of the ⬙Maintenance Schedules⬙ section of this manual. NOTE: Under no circumstances should oil change intervals exceed 6000 miles (10 000 km) or 6 months whichever comes first.
PAGE 347
MAINTAINING YOUR VEHICLE 347 Engine Oil Viscosity (SAE Grade) — 3.8 Liter Engines SAE 5W-20 engine oil is recommended for all operating temperatures. This engine oil improves low temperature starting and vehicle fuel economy. Your engine oil filler cap also shows the recommended engine oil viscosity for your vehicle. For information on engine oil filler cap location, refer to the Engine Compartment illustration in this section. • SAE 10W-30 engine oil is preferred.
PAGE 348
MAINTAINING YOUR VEHICLE Synthetic Engine Oils There are a number of engine oils being promoted as either synthetic or semi-synthetic. If you chose to use such a product, use only those oils that are American Petroleum Institute (API) Certified and have the recommended SAE viscosity grade. Follow the maintenance schedule that describes your driving type.
PAGE 349
MAINTAINING YOUR VEHICLE Belts should be inspected for evidence of cuts, cracks, or glazing, and replaced if there is indication of damage which could result in belt failure. Low generator belt tension can cause battery failure. Also check belt routing to make sure there is no interference between the belts and other engine components. Spark Plugs Spark plugs must fire properly to assure engine performance and emission control. New plugs should be installed at the specified mileage.
PAGE 350
MAINTAINING YOUR VEHICLE Catalytic Converter The catalytic converter requires the use of unleaded fuel only. Leaded gasoline will destroy the effectiveness of the catalyst as an emission control device. Under normal operating conditions, the catalytic converter will not require maintenance. However, it is important to keep the engine properly tuned to assure proper catalyst operation and prevent possible catalyst damage.
PAGE 351
MAINTAINING YOUR VEHICLE WARNING! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your exhaust system. Do not park or operate your vehicle in areas where your exhaust system can contact anything that can burn. In unusual situations involving grossly malfunctioning engine operation, a scorching odor may indicate severe and abnormal catalyst overheating.
PAGE 352
MAINTAINING YOUR VEHICLE WARNING! CAUTION! • Battery fluid is a corrosive acid solution and can burn or even blind you. Don’t allow battery fluid to contact your eyes, skin or clothing. Don’t lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area immediately with large amounts of water. • Battery gas is flammable and explosive. Keep flame or sparks away from the battery.
PAGE 353
MAINTAINING YOUR VEHICLE Air Conditioner Maintenance For best possible performance, your air conditioner should be checked and serviced by an Authorized Dealer at the start of each warm season. This service should include cleaning of the condenser fins and a system performance check. Drive belt tension should also be checked at this time. 353 WARNING! • Use only refrigerants and compressor lubricants approved by the manufacturer for your air conditioning system.
PAGE 354
MAINTAINING YOUR VEHICLE Refrigerant Recovery And Recycling R-134a Air Conditioning Refrigerant is a hydrofluorocarbon (HFC) that is endorsed by the Environmental Protection Agency and is an ozone-saving product. However, the manufacturer recommends that air conditioning service be performed by dealers or other service facilities using recovery and recycling equipment. NOTE: Use only manufacturer approved A/C System Sealers, Stop Leak Products, Seal Conditioners, Compressor Oil, or Refrigerants.
PAGE 355
MAINTAINING YOUR VEHICLE WARNING! Fluid level should be checked on a level surface and with the engine off to prevent injury from moving parts and to insure accurate fluid level reading. Do not overfill. Use only manufacturers recommended power steering fluid. If necessary, add fluid to restore to the proper indicated level. With a clean cloth, wipe any spilled fluid from all surfaces. Refer to Fluids, Lubricants, and Genuine Parts for correct fluid type.
PAGE 356
MAINTAINING YOUR VEHICLE Continued operation could result in failure of the universal joint due to water and dirt contamination of the grease. This would require complete replacement of the joint assembly. The external lock cylinders should be lubricated twice a year, preferably in the fall and spring. Apply a small amount of a high quality lubricant such as Mopar威 Lock Cylinder Lubricant directly into the lock cylinder.
PAGE 357
MAINTAINING YOUR VEHICLE 357 Windshield and Rear Window Washers The fluid reservoir for the windshield washers and the rear window washer is shared. It is located in the engine compartment and should be checked for fluid level at regular intervals. Fill the reservoir with windshield washer solvent (not radiator antifreeze) and operate the system for a few seconds to flush out the residual water. The washer fluid reservoir will hold a full gallon of fluid when the Low Washer Fluid Light illuminates.
PAGE 358
MAINTAINING YOUR VEHICLE vehicle, or when the underside or rear of the vehicle is damaged, have a competent mechanic inspect the complete exhaust system and adjacent body areas for broken, damaged, deteriorated, or mispositioned parts. Open seams or loose connections could permit exhaust fumes to seep into the passenger compartment. In addition, inspect the exhaust system each time the vehicle is raised for lubrication or oil change. Replace as required. WARNING! Exhaust gases can injure or kill.
PAGE 359
MAINTAINING YOUR VEHICLE Engine Coolant Checks Check the engine coolant (antifreeze) protection every 12 months (before the onset of freezing weather, where applicable). If coolant is dirty or rusty in appearance, the system should be drained, flushed and refilled with fresh coolant. Check the front of the A/C condenser for any accumulation of bugs, leaves, etc. If dirty, clean by gently spraying water from a garden hose vertically down the face of the condenser.
PAGE 360
MAINTAINING YOUR VEHICLE CAUTION! Mixing of coolants other than specified HOAT engine coolants, may result in engine damage and may decrease corrosion protection. If a non-HOAT coolant is introduced into the cooling system in an emergency, it should be replaced with the specified coolant as soon as possible. Do not use plain water alone or alcohol base engine coolant (antifreeze) products.
PAGE 361
MAINTAINING YOUR VEHICLE The use of lower quality water will reduce the amount of corrosion protection in the engine cooling system. Please note that it is the owner’s responsibility to maintain the proper level of protection against freezing according to the temperatures occurring in the area where the vehicle is operated. NOTE: Mixing coolant types will decrease the life of the engine coolant and will require more frequent coolant changes.
PAGE 362
MAINTAINING YOUR VEHICLE Disposal of Used Engine Coolant Used ethylene glycol based engine coolant is a regulated substance requiring proper disposal. Check with your local authorities to determine the disposal rules for your community. To prevent ingestion by animals or children do not store ethylene glycol based engine coolant in open containers or allow it to remain in puddles on the ground. If ingested by a child, contact a physician immediately. Clean up any ground spills immediately.
PAGE 363
MAINTAINING YOUR VEHICLE If an examination of your engine compartment shows no evidence of radiator or hose leaks, the vehicle may be safely driven. The vapor will soon dissipate. • Do not overfill the coolant recovery bottle. • Check coolant freeze point in the radiator and in the coolant recovery bottle. If antifreeze needs to be added, contents of coolant recovery bottle must also be protected against freezing.
PAGE 364
MAINTAINING YOUR VEHICLE Pay particular attention to those hoses nearest to high heat sources such as the exhaust manifold. Inspect hose routing to be sure hoses do not come in contact with any heat source or moving component which may cause heat damage or mechanical wear. Insure nylon tubing in these areas has not melted or collapsed. Inspect all hose connections such as clamps and couplings to make sure they are secure and no leaks are present.
PAGE 365
MAINTAINING YOUR VEHICLE Insure nylon tubing in these areas has not melted or collapsed. Inspect all hose connections such as clamps and couplings to make sure they are secure and no leaks are present. NOTE: Often, fluid such as oil, power steering fluid, and brake fluid are used during assembly plant operations to facilitate the assembly of hoses to couplings. Therefore, oil wetness at the hose-coupling area is not necessarily an indication of leakage.
PAGE 366
MAINTAINING YOUR VEHICLE Overfilling of fluid is not recommended because it may cause leaking in the system. Add enough fluid to bring the level up to the requirements described on the brake fluid reservoir. With disc brakes, fluid level can be expected to fall as the brake pads wear. However, low fluid level may be caused by a leak and a checkup may be needed. Use only manufacturers recommended brake fluid, refer to Fluids, Lubricants and Genuine Parts for correct fluid type.
PAGE 367
MAINTAINING YOUR VEHICLE CAUTION! Do not allow petroleum base fluid to contaminate the brake fluid, all brake seal components could be damaged causing partial or complete brake failure. Fuel System Hoses Electronic Fuel Injection high pressure fuel systems are designed with hoses and quick connect fittings which have unique material characteristics to provide adequate sealing and resist attack by deteriorated gasoline.
PAGE 368
MAINTAINING YOUR VEHICLE for correct fluid type. It is important that the transmission fluid be maintained at the prescribed level using the recommended fluid. CAUTION! Using a transmission fluid other than the manufacturers recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder. Using a transmission fluid other than the manufacturers recommended fluid will result in more frequent fluid and filter changes.
PAGE 369
MAINTAINING YOUR VEHICLE 4. Place the gear selector momentarily in each gear position ending with the lever in P (PARK). Wipe the area around the dipstick clean to eliminate the possibility of dirt entering the transmission. 5. Remove the dipstick and determine if the fluid is hot or warm. Hot fluid is approximately 180°F (82°C), which is the normal operating temperature after the vehicle has been driven at least 15 miles (24 km). The fluid cannot be comfortably held between the finger tips.
PAGE 370
MAINTAINING YOUR VEHICLE Severe Usage is defined as: • Police, taxi, limousine, commercial type operation, or trailer towing where the vehicle driven regularly for more than 45 minutes of continuous operation. NOTE: Refer to Section 8 of this manual for Maintenance Schedules. If the transmission is disassembled for any reason, the fluid and filter should be changed. Special Additives Do not add any fluid additives to the transmission.
PAGE 371
MAINTAINING YOUR VEHICLE Overrunning Clutch The fill plug is located on the side of the overrunning clutch housing. The fluid should be maintained at a level even with the bottom of the fill plug hole when the vehicle is parked on a level surface. If it becomes necessary to add or replace the fluid, use only the manufacturers recommended transmission fluid, refer to Fluids, Lubricants and Genuine Parts for correct fluid type. To assure performance, it is important that the proper lubricant be used.
PAGE 372
MAINTAINING YOUR VEHICLE NOTE: Refer to Section 8 of this manual for Maintenance Schedules. The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle. Front And Rear Wheel Bearings Front and rear wheel bearings are permanently sealed. No regular maintenance is required for these components. What Causes Corrosion? Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle.
PAGE 373
MAINTAINING YOUR VEHICLE Washing • Wash your vehicle regularly. Always wash your vehicle in the shade using Mopar Car Wash or a mild car wash soap, and rinse the panels completely with clear water. • If insects, tar or other similar deposits have accumulated on your vehicle, use Mopar Super Kleen Bug and Tar Remover to remove. • Use Mopar Cleaner Wax to remove road film, stains and to protect your paint finish. Take care never to scratch the paint.
PAGE 374
MAINTAINING YOUR VEHICLE • If your vehicle is damaged due to an accident or similar cause which destroys the paint and protective coating, have your vehicle repaired as soon as possible. The cost of such repairs is considered the responsibility of the owner. • All wheels and wheel trim, especially aluminum and chrome plated wheels should be cleaned regularly with a mild soap and water to prevent corrosion. To remove heavy soil, use Mopar Wheel Cleaner or select a nonabrasive, non-acidic cleaner.
PAGE 375
MAINTAINING YOUR VEHICLE Your leather upholstery can be best preserved by regular cleaning with a damp soft cloth. Small particles of dirt can act as an abrasive and damage the leather upholstery and should be removed promptly with a damp cloth. Stubborn soils can be removed easily with a soft cloth and Mopar Total Clean. Care should be taken to avoid soaking your leather upholstery with any liquid.
PAGE 376
MAINTAINING YOUR VEHICLE 1. Clean with a wet soft rag. A mild soap solution may be used, but do not use high alcohol content or abrasive cleaners. If soap is used, wipe clean with a clean damp rag. 2. Dry with a soft tissue. Seat Belt Maintenance Do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage can also weaken the fabric. If the belts need cleaning, use a mild soap solution or lukewarm water.
PAGE 377
MAINTAINING YOUR VEHICLE INTEGRATED POWER MODULE (IPM) Cavity 1 2 3 4 5 6 Integrated Power Module (IPM) An Integrated Power Module is located in the engine compartment near the battery. This center contains maxi fuses, mini fuses and relays. A label that identifies each component is printed on the inside of the cover.
PAGE 378
MAINTAINING YOUR VEHICLE Cavity 10 11 12 13 14 15 40 41 42 Maxi Fuse Spare 40 Amp Green Spare 40 Amp Green Spare 40 Amp Green 40 Amp Green 40 Amp Green 40 Amp Green Description Headlight Washer, Power Liftgate Cavity 24 25 Radiator Fan 1 Anti-Lock Brake System (ABS) Module Driver Door Node Passenger Door Node 26 27 28 29 Front Blower 30 31 Mini Fuse Description 20 Amp Yel- Power Outlet (Selectable) low 15 Amp Blue Radio, Amplifier, Navigation, Hands-Free Phone (HFM), Electronic Vehicle Informa
PAGE 379
MAINTAINING YOUR VEHICLE Cavity 34 35 36 37 38 39 44 45 46 Mini Fuse Spare Spare 20 Amp Yellow 25 Amp Natural 20 Amp Yellow 20 Amp Yellow 25 Amp Natural 10 Amp Red 20 Amp Yellow Description Cavity 47 Electronic Automatic Transaxle (EATX) Solenoid ASD 48 Fuel Pump 49 A/C Clutch, MTV 50 Rear Heated Seats Anti-Lock Brake System (ABS) Ignition Run Passenger Door 379 Mini Fuse Description 20 Amp Yel- Driver Door low 15 Amp Blue PLG, OHC, Body Control Module (BCM), Navigation, Hands-Free Phone (HFM)
PAGE 380
MAINTAINING YOUR VEHICLE CAUTION! • When installing the Integrated Power Module cover, it is important to ensure the cover is properly positioned and fully latched. Failure to do so may allow water to get into the Integrated Power Module, and possibly result in a electrical system failure. • When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating. The use of a fuse with a rating other than indicated may result in a dangerous electrical system overload.
PAGE 381
MAINTAINING YOUR VEHICLE REPLACEMENT LIGHT BULBS LIGHT BULBS — Interior Bulb Number Center & Rear Reading Lights . . . . . . . . . . . . . . . 578 Front Door Courtesy Light . . . . . . . . . . . . . . . . . . 578 Liftgate Light(s). . . . . . . . . . . . . . . . . . . . . . . . . . 578 Overhead Console Reading Lights . . . . . . . . . . . 212–2 Visor Vanity Lights. . . . . . . . . . . . . . . . . . . . . V26377 NOTE: For lighted switches, see your dealer for replacement instructions.
PAGE 382
MAINTAINING YOUR VEHICLE BULB REPLACEMENT 2. Remove the rubber boot seals. Standard Quad Headlights 3. Disconnect the electrical connector. 1. Remove the two screws securing the headlight module to the vehicle and pull the headlight module forward away from the vehicle, disengaging the assembly from the lower attachment clip. 4. Rotate the bulb to the left and replace the bulb. Reinstall the rubber boot seals and then the headlight module. CAUTION! Do not touch the new bulb with your fingers.
PAGE 383
MAINTAINING YOUR VEHICLE High Intensity Discharge Headlights (HID) — If Equipped The headlights are a type of high voltage discharge tube. High voltage can remain in the circuit even with the headlight switch off and the key removed. Because of this, you should not attempt to service a headlight bulb yourself. If a headlight bulb fails, take your vehicle to an authorized dealer for service.
PAGE 384
MAINTAINING YOUR VEHICLE Front Park/Turn Signal and Sidemarker Lights 1. Remove the two screws securing the headlight module to the vehicle and pull the headlight module forward away from the vehicle, disengaging the assembly from the lower attachment clip. 3. Replace the bulb, reinstall the socket and then reinstall the headlight module. Front Fog Light 1. Reach under the front fascia and grasp the front fog light bulb. 2. Twist the front fog light bulb to remove from the fog light module. 3.
PAGE 385
MAINTAINING YOUR VEHICLE 385 Rear Tail, Stop, Turn Signal, Side Marker and Back-up Lights 3. Twist the socket assembly to remove it from the housing. 1. Raise the liftgate. 4. Pull the bulb out of the socket. 2. Remove the two tail light assembly screws and rotate the assembly outward to remove the ball stud form the attaching grommet. 5. Replace the bulb, reinstall the socket, and reattach the tail light assembly. License Light 1.
PAGE 386
MAINTAINING YOUR VEHICLE FLUIDS AND CAPACITIES Fuel (approximate) 89 Octane Engine Oil-With Filter 3.5 Liter Engines (SAE 10W-30, API Certified) 3.8 Liter Engines (SAE 5W-20, API Certified) U.S. 23 gallons Metric 87 liters 5.5 qts 5.0 qts 5.2 liters 4.7 liters 10.7 qts 10.1 liters 11.8 qts 11.2 liters Cooling System * 3.5 Liter Engines (Mopar威 Antifreeze/Coolant 5 Year/ 100,000 Mile Formula or equivalent) 3.
PAGE 387
MAINTAINING YOUR VEHICLE 387 FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant 3.5 Liter Engine Oil 3.8 Liter Engine Oil Spark Plugs Oil Filter, 3.5/3.8 Liter Engines Fuel Selection Fluids, Lubricants and Genuine Parts Mopar威 Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) or equivalent Use API Certified SAE 10W-30 engine oil, refer to oil viscosity chart for correct SAE grade meeting DaimlerChrysler Material Standard MS-6395.
PAGE 388
MAINTAINING YOUR VEHICLE Chassis Component Automatic Transmission AWD Power Transfer Unit AWD Overrunning Clutch AWD Rear Carrier Brake Master Cylinder Power Steering Reservoir Fluids, Lubricants and Genuine Parts Mopar威 ATF+4 Automatic Transmission Fluid. Mopar威 Gear Lubricant 75W-90 or equivalent. Mopar威 ATF+4 Automatic Transmission Fluid. Mopar威 Gear Lubricant 75W-90 or equivalent. Mopar威 DOT 3 and SAE J1703 should be used.
PAGE 389
MAINTENANCE SCHEDULES CONTENTS M A I N T E N A N C E 䡵 Emission Control System Maintenance . . . . . . . . 390 ▫ Schedule “B” . . . . . . . . . . . . . . . . . . . . . . . . 393 䡵 Maintenance Schedules . . . . . . . . . . . . . . . . . . . 390 ▫ Schedule “A” . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 390
M A I N T E N A N C E 390 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
PAGE 391
MAINTENANCE SCHEDULES • Taxi, police, or delivery service (commercial service).〫 • Off-road or desert operation. NOTE: If ANY of these apply to you then change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first and follow schedule “B” of the ⬙Maintenance Schedules⬙ section of this manual. NOTE: Most vehicles are operated under the conditions listed for Schedule ⬙B⬙. Second is Schedule “A”.
PAGE 392
M A I N T E N A N C E S C H E D U L E S 8 392 MAINTENANCE SCHEDULES Once a Month At Each Oil Change • Check tire pressure and look for unusual wear or damage. • Change the engine oil filter. • Inspect the battery and clean and tighten the terminals as required. • Check the fluid levels of coolant bottle, brake master cylinder and transmission, add as needed. • Check all lights and all other electrical items for correct operation. • Inspect the exhaust system. • Inspect the brake hoses.
PAGE 393
SCHEDULE “B” 393 M A I N • Taxi, police, or delivery service (commercial ser- T E vice).〫 N A • Off-road or desert operation. N C NOTE: If ANY of these apply to you then change your E SCHEDULE “B” Follow schedule “B” if you usually operate your vehicle under one or more of the following conditions. Change the automatic transmission fluid and filter every 60,000 miles (96 000 km) if the vehicle is usually operated under one or more of the conditions marked with an 〫. • Trailer towing.
PAGE 394
M 394 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter. A Rotate Tires N C Inspect the brake linings. E Inspect the engine air cleaner filter, replace if S C H E D U L E S 8 necessary. * Replace the engine air cleaner filter. * Change the All Wheel Drive (AWD) power transfer unit fluid. (See note at the end of this chart) Replace the air conditioning filter.
PAGE 395
SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Rotate Tires Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter. Inspect the tie rod ends and boot seals. (Front & Rear) Inspect the PCV valve and replace as necessary.* Change the All Wheel Drive (AWD) power transfer unit fluid. (See note at the end of this chart) Change the All Wheel Drive (AWD) overrunning clutch and rear carrier fluid.
PAGE 396
M 396 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter. A Rotate Tires N C Inspect the brake linings. E Inspect the engine air cleaner filter, replace if S C H E D U L E S 8 necessary. * Replace the engine air cleaner filter. * Change the All Wheel Drive power transfer unit fluid. (See the note at the end of this chart.) Change the All Wheel Drive (AWD) overrunning clutch and rear carrier fluid. (See note at the end of this chart) Replace the air conditioning filter.
PAGE 397
SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Rotate Tires Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter. Inspect the tie rod ends and boot seals. (Front & Rear) Inspect the PCV valve and replace if necessary.* Inspect the serpentine drive belt, replace if necessary. ‡ Change the automatic transmission fluid and filter.
PAGE 398
M 398 SCHEDULE “B” A I N Miles T (Kilometers) E N Change the All Wheel Drive (AWD) power A transfer unit fluid. (See note at the end of this N chart) C E Change the All Wheel Drive (AWD) overrunS C H E D U L E S 8 ning clutch and rear carrier fluid. (See note at the end of this chart) Replace the air conditioning filter.
PAGE 399
SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Rotate Tires Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter Replace the spark plugs. Inspect the tie rod ends and boot seals. (Front & Rear) Check the PCV valve and replace if necessary. Not required if previously changed.* Inspect the serpentine drive belt, replace if necessary.
PAGE 400
M 400 SCHEDULE “B” A I N Miles T (Kilometers) E N Change the All Wheel Drive power transfer A unit fluid. (See the note at the end of this N chart.) C E Change the All Wheel Drive (AWD) overrunS C H E D U L E S 8 ning clutch and rear carrier fluid. (See note at the end of this chart) Replace the air conditioning filter.
PAGE 401
SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Rotate Tires Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter * Replace engine timing belt. Change the All Wheel Drive (AWD) power transfer unit fluid. (See note at the end of this chart) Change the All Wheel Drive (AWD) overrunning clutch and rear carrier fluid. (See note at the end of this chart) Inspect the serpentine drive belt, replace if necessary.
PAGE 402
M 402 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter. A Rotate Tires N C Inspect the brake linings. E Inspect the engine air cleaner filter, replace if necesS C H E D U L E S 8 sary. * Replace the engine air cleaner filter. Inspect the tie rod ends and boot seals. (Front & Rear) Inspect the PCV valve and replace as necessary.* Inspect the serpentine drive belt, replace if necessary. ‡ Change the automatic transmission fluid and filter.
PAGE 403
SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Rotate Tires Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter. Inspect the serpentine drive belt, replace if necessary. ‡ Change the All Wheel Drive (AWD) power transfer unit fluid. (See note at the end of this chart) Change the All Wheel Drive (AWD) overrunning clutch and rear carrier fluid.
PAGE 404
M 404 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter. A Rotate Tires N C Inspect the brake linings. E Inspect the engine air cleaner filter, replace if necesS C H E D U L E S 8 sary. * Replace the engine air cleaner filter. Replace the spark plugs. Inspect the serpentine drive belt, replace if necessary. ‡ Inspect the tie rod ends and boot seals. (Front & Rear) Inspect the PCV valve and replace as necessary.* Change the All Wheel Drive (AWD) power transfer unit fluid.
PAGE 405
SCHEDULE “B” Miles (Kilometers) Change the All Wheel Drive (AWD) overrunning clutch and rear carrier fluid. (See note at the end of this chart) Replace the air conditioning filter. 138, 000 (230 000) * This maintenance is recommended by the manufacture to the owner but is not required to maintain the emissions warranty. ‡ This maintenance is not required if previously replaced. Inspection and service should also be performed anytime a malfunction is observed or suspected. Retain all receipts.
PAGE 406
M 406 SCHEDULE “A” A I SCHEDULE “A” N T Miles E N (Kilometers) A [Months] N C Change engine oil and engine oil filter. E Rotate Tires S C H E D U L E S 8 Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter. Inspect the tie rod ends and boot seals. (Front & Rear) Replace the air conditioning filter.
PAGE 407
SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate Tires Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter. Inspect the tie rod ends and boot seals. (Front & Rear) Check the PCV valve and replace, if necessary.* Inspect the serpentine drive belt, replace if necessary. ‡ Flush and replace the engine coolant at 60 months or 100,000 miles, whichever comes first.
PAGE 408
M 408 SCHEDULE “A” A I N Miles T (Kilometers) E N [Months] A Change engine oil and engine oil filter. N C Rotate Tires E Inspect the brake linings. S C H E D U L E S 8 Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter. Inspect the tie rod ends and boot seals. (Front & Rear) Check and replace the PCV valve , if necessary.* Inspect the serpentine drive belt, replace if necessary. ‡ Replace the spark plugs.
PAGE 409
SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate Tires Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter. Replace engine timing belt. Inspect the tie rod ends and boot seals. (Front & Rear) Check the PCV valve and replace, if necessary.* Inspect the serpentine drive belt, replace if necessary. ‡ Flush and replace the engine coolant at 120 months, if not done at 100,000 miles (160 000 km).
PAGE 410
M 410 SCHEDULE “A” A I N Miles T (Kilometers) E N [Months] A Change engine oil and engine oil filter. N C Rotate Tires E Inspect the brake linings. S C H E D U L E S 8 126, 000 (210 000) [126] X X X Inspect the engine air cleaner filter, replace if necessary. * X Replace the engine air cleaner filter. Inspect the tie rod ends and boot seals. (Front & Rear) Check the PCV valve and replace, if necessary.* Inspect the serpentine drive belt, replace if necessary. ‡ Replace the air conditioning filter.
PAGE 411
SCHEDULE “A” WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.
PAGE 412
PAGE 413
IF YOU NEED CONSUMER ASSISTANCE CONTENTS 䡵 Suggestions For Obtaining Service For Your Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . 414 ▫ Prepare For The Appointment . . . . . . . . . . . . 414 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . . . 414 䡵 Reporting Safety Defects . . . . . . . . . . . . . . . . . . 417 ▫ In Canada . . . . . . . . . . . . . . . . . . . . . . . . . . 417 䡵 Publication Order Forms . . . . . . . . . . . . . . . . . . 418 ▫ Be Reasonable With Requests .
PAGE 414
IF YOU NEED CONSUMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty, discuss additional charges with the service manager. Keep a maintenance log of your vehicle’s service history. This can often provide a clue to the current problem.
PAGE 415
IF YOU NEED CONSUMER ASSISTANCE technicians, special tools, and the latest information to assure your vehicle is fixed correctly and in a timely manner. This is why you should always talk to your dealer’s service manager first. Most matters can be resolved with this process. • If for some reason you are still not satisfied, talk to the general manager or owner of the dealership. They want to know if you need assistance.
PAGE 416
IF YOU NEED CONSUMER ASSISTANCE Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommunication Devices for the Deaf) equipment at its Customer Center. Any hearing or speech impaired customer who has access to a TDD or a conventional teletypewriter (TTY) in the United States can communicate with the manufacturer by dialing 1–800–380–CHRY.
PAGE 417
IF YOU NEED CONSUMER ASSISTANCE WARRANTY INFORMATION (U.S. Vehicles Only) See the Warranty Information Booklet for the terms and provisions of DaimlerChrysler’s warranties applicable to this vehicle. MOPAR姞 PARTS Mopar威 fluids, lubricants, parts, and accessories are available from your dealer. They will help you keep your vehicle operating at its best. REPORTING SAFETY DEFECTS In the 50 United States and Washington D.C.
PAGE 418
IF YOU NEED CONSUMER ASSISTANCE PUBLICATION ORDER FORMS To order the following manuals, you may use either the website or the phone numbers listed below. Visa, Mastercard, American Express, and Discover orders are accepted. If you prefer mailing your payment, please call for an order form. NOTE: A street address is required when ordering manuals. (No P.O. Boxes). • Service Manuals.
PAGE 419
IF YOU NEED CONSUMER ASSISTANCE Call Toll Free at: • 1–800–890–4038 (U.S.) • 1–800–387–1143 (Canada) Or Visit us on the World Wide Web at: • www.techauthority.daimlerchrysler.com • www.daimlerchrysler.ca/manuals DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES The following describes the tire grading categories established by the National highway Traffic Safety Administration.
PAGE 420
IF YOU NEED CONSUMER ASSISTANCE Traction Grades The traction grades, from highest to lowest, are AA, A, B, and C. Those grades represent the tire’s ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance.
PAGE 421
INDEX 10
PAGE 422
INDEX Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 300 Adding Washer Fluid . . . . . . . . . . . . . . . . . . 132,357 Additives, Fuel . . . . . . . . . . . . . . . . . . . . . . . . . 298 Adjustable Pedals . . . . . . . . . . . . . . . . . . . . . . . 137 Air Conditioner Maintenance . . . . . . . . . . . . . . . 353 Air Conditioning . . . . . . . . . . . . . . . . . . . . . 235,240 Air Conditioning Controls . . . . . . . . . . . . . . . . . 235 Air Conditioning Filter . . . . . .
PAGE 423
INDEX Selection Of Lubricant . . . . . . . . . . . . . . . . 367,388 Shifting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 263 Special Additives . . . . . . . . . . . . . . . . . . . . . . 370 Automatic Transmission . . . . . . . . . . . . . . . . . . . 367 Adding Fluid . . . . . . . . . . . . . . . . . . . . . . . . . 368 Fluid and Filter Changes . . . . . . . . . . . . . . . . . 369 Fluid Change . . . . . . . . . . . . . . . . . . . . . . . . . 369 Fluid Level Check . . . . . . . . . . . . .
PAGE 424
INDEX Car Washes . . . . . . . . . . . . . . . . . . . . . . . . . . . . 373 Carbon Monoxide Warning . . . . . . . . . . . . . . . . . 299 Cargo Area Cover . . . . . . . . . . . . . . . . . . . . . . . 156 Cargo Compartment Luggage Carrier . . . . . . . . . . . . . . . . . . . . . . . 158 Cargo Tie-Downs . . . . . . . . . . . . . . . . . . . . . . . . 157 Cassette Tape and Player Maintenance . . . . . . . . . 232 Cassette Tape Player . . . . . . . . . . . . . . . . . . . 207,211 Catalytic Converter .
PAGE 425
INDEX Adding Coolant (Antifreeze) . . . . . . . . . . . . . . 360 Coolant Capacity . . . . . . . . . . . . . . . . . . . . . . 386 Coolant Level . . . . . . . . . . . . . . . . . . . . . . 359,362 Disposal of Used Coolant . . . . . . . . . . . . . . . . 362 Drain, Flush, and Refill . . . . . . . . . . . . . . . . . . 359 Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . 362 Points to Remember . . . . . . . . . . . . . . . . . . . . 362 Pressure Cap . . . . . . . . . . . . . . . . . . . . . .
PAGE 426
INDEX Electric Remote Mirrors . . . . . . . . . . . . . . . . . . . . 82 Electrical Power Outlets . . . . . . . . . . . . . . . . . . . 152 Electronic Speed Control (Cruise Control) . . . . . . 138 Electronic Vehicle Information Center (EVIC) . . . . 176 Emergency, In Case of Hazard Warning Flasher . . . . . . . . . . . . . . . . . 318 Jacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 320 Jump Starting . . . . . . . . . . . . . . . . . . . . . . . . . 327 Overheating . . . . . . . . .
PAGE 427
INDEX Air Conditioning . . . . . . . . . . . . . . . . . . . . 253,354 Automatic Transaxle . . . . . . . . . . . . . . . . . . . . 369 Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . 348,387 Engine Oil Disposal . . . . . . . . . . . . . . . . . . . . 348 Flashers Hazard Warning . . . . . . . . . . . . . . . . . . . . . . . 318 Turn Signal . . . . . . . . . . . . . . . . . . . . . 169,384,385 Floor Console . . . . . . . . . . . . . . . . . . . . . . . . . . 155 Fluid Capacities . . . . . . . . .
PAGE 428
INDEX Gasoline (Fuel) . . . . . . . . . . . . . . . . . . . . . . . . . 296 Gasoline, Reformulated . . . . . . . . . . . . . . . . . . . 297 Gauges Coolant Temperature . . . . . . . . . . . . . . . . . . . . 168 Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169 Speedometer . . . . . . . . . . . . . . . . . . . . . . . . . 169 Tachometer . . . . . . . . . . . . . . . . . . . . . . . . . . 172 Gearshift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 429
INDEX Illuminated Entry . . . . . . . . . . . . . . . . . . . . . . . . 15 Immobilizer (Sentry Key) . . . . . . . . . . . . . . . . . . . 12 Indicator, Traction Control . . . . . . . . . . . . . . . . . 171 Infant Restraint . . . . . . . . . . . . . . . . . . . . . . . . . . 65 Information Center, Vehicle . . . . . . . . . . . . . . . . . 176 Instrument Cluster . . . . . . . . . . . . . . . . . 166,167,168 Instrument Panel and Controls . . . . . . . . . . . . . . 165 Instrument Panel Lens Cleaning . . . .
PAGE 430
INDEX Automatic Headlights . . . . . . . . . . . . . . . . . . . 128 Back-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 385 Brake Warning . . . . . . . . . . . . . . . . . . . . . . . . 170 Bulb Replacement . . . . . . . . . . . . . . . . . . . 381,382 Courtesy/Reading . . . . . . . . . . . . . . . . . . . . . 125 Cruise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173 Daytime Running . . . . . . . . . . . . . . . . . . . . . . 128 Dimmer Switch, Headlight . . . . . . . .
PAGE 431
INDEX Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 278 Locks Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Lower Anchors and Tether for CHildren (LATCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61,63 Lubrication, Body . . . . . . . . . . . . . . . . . . . . . . . 356 Luggage Rack (Roof Rack) . . . . . . . . . . . . . . . . . 158 Maintenance, Airbag . . . . . . . . . . . . . . . . . . . . . . 58 Maintenance Free Battery . . . . . . . . . . . .
PAGE 432
INDEX Occupant Restraints . . . . . . . . . . . . . . . . . . . . . . . 33 Octane Rating, Gasoline (Fuel) . . . . . . . . . . . . . . 296 Odometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172 Oil, Engine . . . . . . . . . . . . . . . . . . . . . . . . . 344,387 Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . 386 Change Interval . . . . . . . . . . . . . . . . . . . . . . . 345 Checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . 344 Disposal . . . . . . .
PAGE 433
INDEX Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82 Outlet (Auxiliary Electrical Outlet) . . . . . . . . . . 152 Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106,107 Steering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 271 Steering, Checking . . . . . . . . . . . . . . . . . . . . . 354 Sunroof . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149 Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 434
INDEX Restraint, Head . . . . . . . . . . . . . . . . . . . . . . . . . 108 Restraints, Child . . . . . . . . . . . . . . . . . . . . . . . 60,68 Restraints, Infant . . . . . . . . . . . . . . . . . . . . . . . . . 65 Retractable Cargo Area Cover . . . . . . . . . . . . . . . 156 Rocking Vehicle When Stuck . . . . . . . . . . . . . . . . 330 Roof Rack (Luggage Rack) . . . . . . . . . . . . . . . . . 158 Rotation, Tires . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 435
INDEX Security Alarm (Theft Alarm) . . . . . . . . . . . . . . . . 26 Selection of Coolant (Antifreeze) . . . . . . . . . . 359,387 Sentry Key (Immobilizer) . . . . . . . . . . . . . . . . . . . 12 Sentry Key Programming . . . . . . . . . . . . . . . . . . . 14 Service Assistance . . . . . . . . . . . . . . . . . . . . . . . 414 Service Contract . . . . . . . . . . . . . . . . . . . . . . . . . 416 Service Engine Soon Light (Malfunction Indicator) . 173 Service Manuals . . . . . . . . . . . . . . . . . . .
PAGE 436
INDEX System, Navigation . . . . . . . . . . . . . . . . . . . . . . 233 Tachometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172 Tape Player . . . . . . . . . . . . . . . . . . . . . . . . . . . . 211 Temperature Control, Automatic (ATC) . . . . . . . . 243 Temperature Gauge, Engine Coolant . . . . . . . 168,319 Tether Anchor, Child Restraint . . . . . . . . . . . . . 61,63 Theft Alarm (Security Alarm) . . . . . . . . . . . . . . . . 26 Theft System Arming . . . . . . . . . . . . . . .
PAGE 437
INDEX Spare Tire . . . . . . . . . . . . . . . . . . . . . . . . . . . 322 Spinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . 287 Tread Wear Indicators . . . . . . . . . . . . . . . . . . . 288 Tongue Weight/Trailer Weight . . . . . . . . . . . . . . 308 Towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 304 Disabled Vehicle . . . . . . . . . . . . . . . . . . . . . . . 331 Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 307 Recreational . . . . . . . . . .
PAGE 438
INDEX Uniform Tire Quality Grades . . Universal Joints . . . . . . . . . . . Universal Transmitter . . . . . . . Unleaded Gasoline . . . . . . . . . Untwisting Procedure, Seat Belt . . . . . . . . . . . . . . . . . 419 . . . . . . . . . . . . . 355 . . . . . . . . . . . . . 142 . . . . . . . . . . . . . 296 . . . . . . . . . . . . . . 41 Vanity Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . 82 Variance, Compass . . . . . . . . . . . . . . . . . . . . . . .
PAGE 439
NOTES
PAGE 440
NOTES