SECTION TABLE OF CONTENTS PAGE 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 3 4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION CONTENTS 䡵 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 Vehicle Identification Number . . . . . . . . . . . . . . 6 䡵 How To Use This Manual . . . . . . . . . . . . . . . . . 4 䡵 Vehicle Modifications / Alterations . . . . . . . . . . 7 䡵 Warnings And Cautions . . . . . . . . . . . . . . . . . .
INTRODUCTION INTRODUCTION This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a Warranty Information Booklet and various customer oriented documents. You are urged to read these publications carefully. Following the instructions and recommendations in this manual will help assure safe and enjoyable operation of your vehicle.
INTRODUCTION 5 1
INTRODUCTION WARNINGS AND CAUTIONS This manual contains WARNINGS against operating procedures which could result in an accident or bodily injury. It also contains CAUTIONS against procedures which could result in damage to your vehicle. If you do not read this entire manual you may miss important information. Observe all Warnings and Cautions. VEHICLE IDENTIFICATION NUMBER The vehicle identification number (VIN) is located near the left front corner of the windshield.
INTRODUCTION 7 VEHICLE MODIFICATIONS / ALTERATIONS 1 WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS 䡵 A Word About Your Keys . . . . . . . . . . . . . . . . .11 ▫ Power Door Locks . . . . . . . . . . . . . . . . . . . . .16 ▫ Ignition Key Removal . . . . . . . . . . . . . . . . . . .11 ▫ Child Protection Door Lock . . . . . . . . . . . . . . .19 ▫ Key-In-Ignition Reminder . . . . . . . . . . . . . . . .12 䡵 Remote Keyless Entry . . . . . . . . . . . . . . . . . . . .20 ▫ Horn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Power Windows . . . . . . . . . . . . . . . . . . . . . . .26 ▫ Seat Belt Extender . . . . . . . . . . . . . . . . . . . . . .38 䡵 Trunk Lock And Release . . . . . . . . . . . . . . . . . .29 ▫ Driver And Right Front Passenger Supplemental Restraint System (SRS) - Airbag . . . . . . . . . . . .39 䡵 Trunk Safety Warning . . . . . . . . . . . . . . . . . . . .30 ▫ Trunk Emergency Release . . . . . . . . . . . . . . . .31 䡵 Occupant Restraints . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 A WORD ABOUT YOUR KEYS You can insert the double sided keys into the locks with either side up. Ignition Key Removal The shift lever must be in PARK. Turn the key to the LOCK position, then remove the key. Vehicle Key Ignition Key Positions The dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys from your dealer.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE vehicle information center (EVIC) — if equipped. Refer to Personal Settings in the Electronic Vehicle Information Center (EVIC) Section for details. Key-In-Ignition Reminder If you open the driver’s door and the key is in the ignition switch, a chime will sound to remind you to remove the key. WARNING! NOTE: The Key-In-Ignition reminder only sounds when the ignition key is placed in the LOCK or ACC positions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 The Sentry Key Immobilizer System does not need to be armed or activated. Operation of the system is automatic regardless of whether or not the vehicle is locked or unlocked. During normal operation, the Vehicle Theft Alarm Indicator Light will come on for three (3) seconds immediately after the ignition switch is turned on for a bulb check. Afterwards, if the bulb remains on, this indicates a problem with the electronics.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE At the time of purchase, the original owner is provided with a four digit PIN number. This number is required for dealer replacement of keys. Duplication of keys may be performed at an authorized dealer or by using the Customer Key Programming procedure. This procedure consists of programming a blank key to the vehicle electronics. A blank key is one which has never been programmed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 General Information The Sentry Key system complies with FCC rules part 15 and with RSS-210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. DOOR LOCKS Manual Door Locks Lock the doors by pushing down on the door lock plunger on each door trim panel. • This device must accept any interference that may be received, including interference that may cause undesired operation.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • For personal security and safety in the event of an accident, lock the vehicle doors as you drive as well as when you park and leave the vehicle. • When leaving the vehicle always remove the key from the ignition lock, and lock your vehicle. Do not leave children unattended in the vehicle, or with access to an unlocked vehicle. Unsupervised use of vehicle equipment may cause severe personal injuries and death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 Automatic Door Locks The doors will lock automatically on vehicles with power door locks if all of the following conditions are met: For vehicles not equipped with the EVIC, the Automatic Door Locks can be enabled or disabled by performing the following procedure: 1. The Auto Lock feature is enabled. 1. Close all doors and place the key in the ignition. 2. The transmission is in gear. 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Depress the power door lock switch to lock the doors. 2. The transmission was in gear and the vehicle speed returned to 0 mph (0 km/h). 3. The transmission is in NEUTRAL or PARK. 4. The driver door is opened. 5. The doors were not previously unlocked. 6. The vehicle speed is 0 mph (0 km/h). The Auto Unlock feature can be enabled or disabled.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 Child Protection Door Lock To provide a safer environment for small children riding in the rear seats, the rear doors are equipped with a child protection door lock system. WARNING! Avoid trapping anyone in the vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged. Ignition Key Position 3. Depress the power door unlock switch to unlock the doors. 4.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To activate the system, open the rear door and move the child lock control, located near the door’s rear latch, to the ON position. REMOTE KEYLESS ENTRY This system allows you to lock or unlock the doors, open the trunk, or activate the panic alarm from distances up to about 23 feet (7 meters) using a hand held radio transmitter. The transmitter need not be pointed at the vehicle to activate the system.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 Vehicle Information Center (EVIC). Refer to “Turn Headlights on with Remote Key Unlock” under “Personal Settings” in the Electronic Vehicle Information Center (EVIC) section of this manual for details. NOTE: The system can also be programmed to unlock all doors on the first press of the UNLOCK button.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Pressing the LOCK button on the keyfob while you are inside the vehicle will activate the Security Alarm. Opening a door with the Security Alarm activated will cause the alarm to sound. Press the UNLOCK button to deactivate the Security Alarm. The “Remote Unlock Driver’s Door 1st” feature can be reactivated by repeating this procedure. To lock the doors: Press and release the LOCK button on the transmitter to lock all doors.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 • When you turn off the panic alarm by pressing the PANIC button a second time, you may have to be closer to the vehicle due to the radio frequency noises of the system. 4. Test the flash lights with LOCK feature while outside of the vehicle, by pressing the LOCK button on the key fob with the ignition in the LOCK position, and the key removed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If your Remote Keyless Entry transmitter fails to operate from a normal distance, check for these two conditions. 1. A weak battery in the transmitter. The expected life of the battery is a minimum of three years. 2. Closeness to a radio transmitter such as a radio station tower, airport transmitter, and some mobile or CB radios. Transmitter Battery Service The recommended replacement battery is one CR2032 battery.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 VEHICLE THEFT ALARM — IF EQUIPPED The Vehicle Theft Alarm system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation. If something triggers the alarm, the system will prevent the vehicle from starting and provide the following audible and visual signals: the horn will pulse; the headlights will flash; the park lights will flash; and the Vehicle Theft Alarm Indicator light in the instrument cluster will flash.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The Vehicle Theft Alarm system is designed to protect your vehicle, however, you can create conditions where the system will give you a false alarm. If one of the previously described arming sequences has occurred, the system will arm regardless of whether you are in the vehicle or not. If you remain in the vehicle and open a door, the alarm will sound. If this occurs, disarm the system.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 The window lock switch on the driver’s door allows you to disable the window controls on the passenger doors. When the lock switch is pressed, the window controls on the passenger doors will not illuminate and the passenger windows will be disabled. To open the window part way, press the window switch to the first detent and release it when you want the window to stop.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Auto Up Feature with Anti–Pinch Protection — If Equipped Lift the window switch to the second detent, release, and the window will go up automatically. To stop the window from going all the way up during the auto-up operation, push down on the switch briefly. To close the window part way, lift the window switch to the first detent and release when you want the window to stop.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 Reset Any time the vehicle battery is disconnected or goes dead the auto-up function will be disabled. To reactivate the auto-up feature perform the following steps after vehicle power is restored: 1. Pull the window switch up to close window completely and continue to hold the switch up for an additional two seconds after the window is closed. 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The trunk lid can be released from outside the vehicle by pressing the trunk button on the Remote Keyless Entry Transmitter two times. With the ignition ON, the trunk open symbol will display in the instrument cluster indicating that the trunk is open. The odometer display will reappear once the trunk is closed. With the key in lock position or key out, the trunk open symbol will be displayed until the trunk is closed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 Trunk Emergency Release Emergency Release The trunk of your vehicle is equipped with an emergency release handle. It is located on the inside of the trunk lid, near the latch, and is coated so that it glows in a darkened trunk. Pull on the handle to open the trunk. OCCUPANT RESTRAINTS Some of the most important safety features in your vehicle are the restraint systems.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! In a collision, you and your passengers can suffer much greater injuries if you are not properly buckled up. You can strike the interior of your vehicle or other passengers, or you can be thrown out of the vehicle. Always be sure you and others in your vehicle are buckled up properly. Buckle up even though you are an excellent driver, even on short trips. Someone on the road may be a poor driver and cause a collision which includes you.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 WARNING! • Wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and can take the forces of a collision the best. Wearing your belt in the wrong place could make your injuries in a collision much worse. You might suffer internal injuries, or you could even slide out of part of the belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you as well. In a sudden stop you could move too far forward, increasing the possibility of injury. Wear your seat belt snugly. • A belt that is worn under your arm is very dangerous.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 WARNING! WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as possible and keep it snug. • A twisted belt can’t do its job as well. In a collision it could even cut into you. Be sure the belt is straight. If you can’t straighten a belt in your vehicle, take it to your dealer and have it fixed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Adjustable Upper Shoulder Belt Anchorage In the driver and front passenger seats, the shoulder belt can be adjusted upward or downward to position the belt away from your neck. Push and fully depress the button above the webbing to release the anchorage, and then move it up or down to the position that serves you best. you’ll prefer a higher position. When you release the anchorage, try to move it up or down to make sure that it is locked in position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 are single use items. After a collision that is severe enough to deploy the airbags and pretensioners, both must be replaced. Enhanced Seat Belt Reminder System (BeltAlert) If the driver’s or front passenger’s seat belt has not been buckled within 60 seconds of starting the vehicle and if the vehicle speed is greater than 5 mph (8 km/h), the Enhanced Warning System (BeltAlert) will alert the driver or front passenger to buckle their seat belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The Enhanced Warning System (BeltAlert) can be reactivated by repeating this procedure. NOTE: Although the Enhanced Warning System (BeltAlert) has been deactivated, the Seat Belt Warning Light will continue to illuminate while the driver’s or front passenger’s seat belt remains unbuckled. Seat Belts and Pregnant Women We recommend that pregnant women use the seat belts throughout their pregnancy. Keeping the mother safe is the best way to keep the baby safe.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 Driver and Right Front Passenger Supplemental Restraint System (SRS) - Airbag NOTE: The front airbags are certified to the Federal regulations that allow less forceful deployment. The front airbags have a multistage inflator design. This may allow the airbag to have different rates of inflation that are based on collision severity and occupant size.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE This vehicle may also be equipped with left and right side curtain airbags to protect the driver and passengers sitting next to a window. If the vehicle is equipped with side curtain airbags, they are located above the side windows. Their covers are also labeled SRS AIRBAG. WARNING! • Do not put anything on or around the front airbag covers or attempt to manually open them.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 Along with the seat belts, front airbags work with the instrument panel knee bolsters to provide improved protection for the driver and front passenger. Side Curtain Airbags also work with seat belts to improve occupant protection. The seat belts are designed to protect you in many types of collisions. The front airbags deploy in moderate to severe frontal collisions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. You should read the instructions provided with your child restraint to make sure that you are using it properly. 3. All occupants should use their seat belts properly. 4. The driver and front passenger seats should be moved back as far as practical to allow the airbags time to inflate. 5. If your vehicle has left and right side curtain airbags, do not lean against the door, airbags will inflate forcefully into the space between you and the door. 6.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 Air Bag System Components The airbag system consists of the following: • Occupant Restraint Controller • Airbag Warning Light • Driver Airbag • Passenger Airbag • Side Curtain Airbags above Side Windows (if equipped) • Side Remote Acceleration Sensors (if equipped) • Steering Wheel and Column • Instrument Panel • Interconnecting Wiring • Knee Impact Bolsters • Front Acceleration Sensors • Driver and Front Passenger Seat Belt Pretensioners • Occupant Classifica
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Also, the ORC turns on the airbag warning light and PAD indicator light in the instrument panel for 6 to 8 seconds for a self-check when the ignition is first turned on. After the self-check, the airbag warning light will turn off. The PAD indicator light will function normally (refer to information on Passenger Airbag Disable (PAD) Indicator Light in this section).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 and will not inflate. If the PAD indicator light is not illuminated, DO NOT assume the air bag is turned off and move the child restraint to the rear seat. A deploying passenger air bag can cause death or serious injury to a child in a rear facing infant seat.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The OCS classifies an occupant using weight sensors mounted in the base of the front passenger seat. Any weight on the seat will be sensed by the system. Objects hanging on the seat or other passengers pushing down on the seat will also be sensed. The weight of an adult will cause the system to turn the airbag on. In this case, the OCS has classified the occupant of the seat as an adult.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 Indicator Light and the Airbag Warning Light. Once the lodged object is removed, the fault will be automatically cleared after a short period of time. • The Driver and Passenger Airbag/Inflator Units are located in the center of the steering wheel and the right side of the instrument panel. When the ORC detects a collision requiring the airbags, it signals the inflator units. A large quantity of nontoxic gas is generated to inflate the front airbags.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE milliseconds (about one quarter of the time it takes to blink your eyes) with enough force to injure you if you are not belted and seated properly, or if items are positioned in the area where the side curtain airbag inflates. This especially applies to children. The side curtain airbag is only about 3-1/2 inches (9 cm) thick when it is inflated.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 WARNING! If you do have a collision which deploys the airbags, any or all of the following may occur: Unapproved modifications or service procedures to the front passenger seat assembly, its related components, or seat cover may inadvertently change the airbag deployment in case of a frontal crash. This could result in death or serious injury to the front seat passenger if the vehicle is involved in an accident.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • It is not advisable to drive your vehicle after the airbags have been deployed. If you are involved in another collision, the airbags will not be in place to protect you. Maintaining Your Airbag System WARNING! • Modifications to any part of the airbag system could WARNING! Deployed airbags can’t protect you in another collision. Have the airbags replaced by an authorized dealer as soon as possible.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 Airbag Light You will want to have the airbags ready to inflate for your protection in an impact. While the airbag system is designed to be maintenance free, if any of the following occurs, have an authorized dealer service the system promptly: • The airbag light does not come on or flickers during the 6 to 8 seconds when the ignition switch is first turned on. • The light remains on or flickers after the 6 to 8 second interval.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE treated confidentially. Confidential data will not be disclosed by DaimlerChrysler to any third party except when: 1. Used for research purposes, such as to match data with a particular crash record in an aggregate database, provided confidentiality of personal data is thereafter preserved 2. Used in defense of DaimlerChrysler product litigation involving a 3. Requested by police under a legal warrant 4.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 WARNING! In a collision, an unrestrained child, even a tiny baby, can become a missile inside the vehicle. The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are. The child and others could be badly injured. Any child riding in your vehicle should be in a proper restraint for the child’s size.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint. • A rearward facing child restraint should only be used in a rear seat.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 Older Children and Child Restraints Children who weigh more than 20 lbs (9 kg) and who are older than one year can ride forward-facing in the vehicle. Forward-facing child seats and convertible child seats used in the forward-facing direction are for children who weigh 20 to 40 lbs (9 to 18 kg) and who are older than one year. These child seats are also held in the vehicle by the lap/shoulder belt or the LATCH child restraint anchorage system.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE LATCH-compatible child restraint systems are now available. However, because the lower anchorages are to be introduced over a period of years, child restraint systems having attachments for those anchorages will continue to also have features for installation using the vehicle’s seat belts. Child restraints having tether straps and hooks for connection to the top tether anchorages have been available for some time.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 The rear seat lower anchorages are round bars, located at the rear of the seat cushion where it meets the seat back. The location of the lower anchorages are identified by a symbol on the seat back. You will easily feel them if you run your finger along the intersection of the seatback and seat cushion surfaces. In addition, there are tether strap anchorages behind each rear seating position located in the panel between the rear seat back and the rear window.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE restraint installation, instead of tucking the seat belt behind the child restraint, route the seat belt through the child restraint belt path and then buckle it. This should stow the seat belt out of the reach of an inquisitive child. Remind all children in the vehicle that the seat belts are not toys and should not be played with, and never leave your child unattended in the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 3. Attach the tether strap hook (A) of the child restraint to the anchor (B) and remove slack in the tether strap according to the child restraint manufacturer’s instructions. WARNING! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor positions directly behind the child seat to secure a child restraint top tether strap. Tether Strap Mounting 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ENGINE BREAK-IN RECOMMENDATIONS A long break-in period is not required for the engine in your new vehicle. Drive moderately during the first 300 miles (500 km). After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable. While cruising, brief full-throttle acceleration, within the limits of local traffic laws, contributes to a good break-in. Wide open throttle acceleration in low gear can be detrimental and should be avoided.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 Safety Checks You Should Make Inside The Vehicle Periodic Safety Checks You Should Make Outside The Vehicle Seat Belts Inspect the belt system periodically, checking for cuts, frays and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Tires Examine tires for excessive tread wear or uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 䡵 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67 ▫ Inside Day/Night Mirror . . . . . . . . . . . . . . . . .67 ▫ Automatic Dimming Inside Mirror — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . .67 ▫ Driver’s Side Outside Mirror Auto Dimmer — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . .68 3 ▫ Heated Remote Control Mirrors — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Power Seats . . . . . . . . . . . . . . . . . . . . . . . . . .90 ▫ Headlight Switch . . . . . . . . . . . . . . . . . . . . . 102 ▫ Power Reclining Seats . . . . . . . . . . . . . . . . . . .91 ▫ Multi-Function Lever . . . . . . . . . . . . . . . . . . . 102 ▫ Lumbar Support . . . . . . . . . . . . . . . . . . . . . . .92 ▫ Headlights, Parking Lights, Instrument Panel Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 65 ▫ Windshield Washers . . . . . . . . . . . . . . . . . . . 107 ▫ Rain Sensing Wipers—If Equipped . . . . . . . . . 107 ▫ Mist Feature . . . . . . . . . . . . . . . . . . . . . . . . . 108 ▫ Headlights On With Wipers (Available With Auto Headlights Only) . . . . . . 108 䡵 Electronic Stability Program (ESP) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 117 ▫ Synchronizing ESP . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Using HomeLink . . . . . . . . . . . . . . . . . . . . . 127 ▫ Ignition Off Operation . . . . . . . . . . . . . . . . . . 131 ▫ Erasing HomeLink Buttons . . . . . . . . . . . . . . 127 ▫ Sunroof Fully Closed . . . . . . . . . . . . . . . . . . . 131 ▫ Reprogramming a Single HomeLink Button . . . 127 䡵 Electrical Power Outlets . . . . . . . . . . . . . . . . . 131 ▫ Security . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 67 MIRRORS Inside Day/Night Mirror Adjust the mirror to center on the view through the rear window. A two point pivot system allows for horizontal and vertical adjustment of the mirror. Automatic Dimming Inside Mirror — If Equipped If the switch is in the “AUTO” position the mirror will automatically adjust for annoying headlight glare from vehicles behind you.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean. Driver’s Side Outside Mirror Auto Dimmer — If Equipped The driver’s side outside mirror automatically adjusts for annoying headlight glare from vehicles behind you. This feature can be turned on or off by pressing the button at the base of the Inside Rearview Mirror.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 69 WARNING! Vehicles and other objects seen in the right side convex mirror will look smaller and farther away than they really are. Relying too much on your right side mirror could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in this convex mirror.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Illuminated Vanity Mirrors — If Equipped An illuminated vanity mirror is on the sun visor. To use the mirror, rotate the sun visor down and swing the mirror cover upward. The light turns on automatically. Closing the mirror cover turns off the lights. HANDS–FREE COMMUNICATION (UConnect™) — IF EQUIPPED UConnect™ is a voice-activated, hands-free, in- vehicle communications system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 71 The UConnect™ phonebook enables you to store up to 32 names and four numbers per name. Each language has a separate 32 name phonebook accessible only in that language. This system is driven through your Bluetooth™ Hands-Free profile cellular phone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE system can either be adjusted from the radio volume control knob, or from the steering wheel radio control (right switch), if so equipped. The radio display will be used for visual prompts from the UConnect™ system such as ⬙CELL⬙ or caller ID on certain radios. Operations Voice commands can be used to operate the UConnect™ system and to navigate through the UConnect™ menu structure. Voice commands are required after most UConnect™ system prompts.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 73 Cancel Command At any prompt, after the voice on beep, you can say ⬙Cancel⬙ and you will be returned to the main menu. However, in a few instances the system will take you back to the previous menu. Pair (Link) UConnect™ System to a Cellular Phone To begin using your UConnect™ system, you must pair your compatible Bluetooth™ enabled cellular phone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • For identification purposes, you will be prompted to give the UConnect™ system a name for your cellular phone. Each cellular phone that is paired should be given a unique phone name. • You will then be asked to give your cellular phone a priority level between 1 and 7, 1 being the highest priority. You can pair up to seven cellular phones to your UConnect™ system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 75 • After the ⬙Ready⬙ prompt and the following beep, say the name of the person you want to call. For example, you can say ⬙John Doe,⬙ where John Doe is a previously stored name entry in the UConnect™ phonebook. Refer to ⬙Add Names to Your UConnect™ Phonebook,⬙ to learn how to store a name in the phonebook. • When prompted, enter the number designation (e.g.: ⬙Home,⬙ ⬙Work,⬙ ⬙Mobile,⬙ or ⬙Pager⬙).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After the ⬙Ready⬙ prompt and the following beep, say ⬙Phonebook Edit.⬙ • You will then be asked for the name of the phonebook entry that you wish to edit. • Next, choose the number designation (home, work, mobile, or pager) that you wish to edit. • When prompted, recite the new phone number for the phonebook entry that you are editing.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 77 Delete All Entries in the UConnect™ Phonebook • Press the ’Phone’ button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Phonebook Erase All.⬙ • The UConnect™ system will ask you to verify that you wish to delete all the entries from the phonebook. • After confirmation, the phonebook entries will be deleted. List All Names in the UConnect™ Phonebook • Press the ’Phone’ button to begin.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Answer or Reject an Incoming Call - Call Currently in Progress If a call is currently in progress and you have another incoming call, you will hear the same network tones for call waiting that you normally hear when using your cell phone. Press the ’Phone’ button to place the current call on hold and answer the incoming call. NOTE: The UConnect™ system compatible phones in market today do not support rejecting an incoming call when another call is in progress.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 79 established, press and hold the ’Phone’ button until you hear a double beep indicating that the two calls have been joined into one conference call. Call Termination To end a call in progress, momentarily press the ⬘Phone’ button. Only the active call(s) will be terminated and if there is a call on hold, it will become the new active call. Redial • Press the ’Phone’ button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Redial.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Continue to follow the system prompts to complete language selection. the paired cellular phone to call the emergency number. This feature is only supported in the USA. After selecting one of the languages, all prompts and voice commands will be in that language. NOTE: The emergency number dialed is based on the Country where the vehicle is purchased (911 for USA and Canada and 060 for Mexico).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 81 NOTE: The Towing Assistance number dialed is based on the Country where the vehicle is purchased (1-800528-2069 for USA, 1-877-213-4525 for Canada, 55-14-3454 for Mexico city and 1-800-712-3040 for outside Mexico city in Mexico). You can use your UConnect™ system to access a voicemail system or an automated service, such as, paging service or automated customer service.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE aѧ,⬙ you could press the ’Voice Recognition’ button and say ⬙Pair a Phone⬙ to select that option without having to listen to the rest of the voice prompt. Turning Confirmation Prompts On/Off Turning confirmation prompts off will stop the system from confirming your choices (e.g. the UConnect™ system will not repeat a phone number before you dial it). • Press the ’Phone’ button to begin.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83 • After the ⬙Ready⬙ prompt and the following beep, say ⬙Mute.⬙ In order to un-mute the UConnect™ system: • Press the ’Voice Recognition’ button. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Mute-off.⬙ Information Service When using AT&T Wireless Service, dialing to phone number ⬙#121,⬙ you can access voice activated automated system to receive news, weather, stocks, traffic, etc. related information.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE button and say “Select” or “Delete.” Also, see the next two sections for an alternate way to “select” or “delete” a paired phone. Select another Cellular Phone This feature allows you to select and start using another phone with the UConnect™ system. The phone must have been previously paired to the UConnect™ system that you want to use it with. • Press the ’Phone’ button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Setup Select Phone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85 Things You Should Know About Your UConnect™ System Voice Recognition (VR) • Always wait for the beep before speaking. • Speak normally, without pausing, just as you would speak to a person sitting approximately eight (8) feet away from you. • Make sure that no one other than you is speaking during a voice recognition period.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Far End Audio Performance • Audio quality is maximized under: • low-to-medium blower setting, • low-to-medium vehicle speed, • low road noise, • smooth road surface, • fully closed windows, and • dry weather condition. • Operation from driver seat. • Performance, such as, audio clarity, echo. and loudness to a large degree, rely on the phone and network, and not the UConnect™ system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE North American English Primary Alternate(s) Zero Oh Add location Add new All All of them Confirmation prompts Confirmations prompts Delete a name Delete Language Select language List names List all List paired phones List phones Pager Beeper Phone pairing Pairing Phonebook Phone book Return to main menu Return.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91 WARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust the seat only while the vehicle is parked. 3 CAUTION! Do not place any article under a power seat as it may cause damage to the seat controls.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Lumbar Support This feature allows you to increase or decrease the amount of lumbar support. Turn the control lever forward to increase and rearward to decrease the desired amount of lumbar support. The front driver’s and passenger seats are heated. The controls for each heater are located near the bottom center of the instrument panel. After turning on the ignition, you can choose from High, Off, or Low heat settings.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 Pressing the switch a second time will select low-level heating. Pressing the switch a third time will shut the heating elements off. When high-temperature heating is selected, the heaters provide a boosted heat level during the first four minutes of operation after heating is activated. The heat output then drops to the normal high-temperature level.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Head Restraints Head restraints can reduce the risk of whiplash injury in the event of impact from the rear. Adjustable restraints should be adjusted so that the upper edge is as high as practical. Folding Rear Seat The head restraints have a locking button which must be pushed in to lower the head restraint. The restraints may be raised without pushing in the button.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 WARNING! The cargo area in the rear of the vehicle (with the rear seatbacks in the locked-up or folded down position) should not be used as a play area by children when the vehicle is in motion. They could be seriously injured in an accident. Children should be seated and using the proper restraint system. DRIVER MEMORY SEAT This feature allows the driver to store up to two different memory profiles for easy recall through a memory switch.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 1. Adjust all memory profile settings to desired preferences (i.e. seat, side mirror, adjustable pedals [if equipped], power tilt and telescopic steering column [if equipped], and radio station presets). 2. Press and release the Set (S) button on the memory switch, then press the side of the rocker switch labeled (1) within 5 seconds. The Electronic Vehicle Information Center (EVIC) — if equipped will display which memory position is being set.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 3. Press and release the Set (S) button on the memory switch, then press and release the side of the rocker switch labeled 1 or 2 accordingly. ⬙Memory Profile Set” (1 or 2) will display in the instrument cluster on vehicles equipped with the Electronic Vehicle Information Center (EVIC). 4. Press and release the LOCK button on the transmitter within 10 seconds.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The Easy Entry/Easy Exit feature is disabled when the vehicle is delivered from the factory. The Easy Entry/Easy Exit feature can be enabled or disabled through the programmable features in the Electronic Vehicle Information Center (EVIC). Refer to “Automatically Move Seat Back on Exit” under “Personal Settings (Customer Programmable Features)” under “Electronic Vehicle Information Center (EVIC)” in Section 4 of this manual for details.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99 • The pedals cannot be adjusted when the vehicle is in R (Reverse) or when the Speed Control is ON. One of the following message will display in the Electronic Vehicle Information Center (EVIC) — if equipped if a pedal adjustment is attempted when the system is locked out: “Adjustable Pedal Disabled — Cruise Control Engaged” or “Adjustable Pedal Disabled — Vehicle In Reverse.” TO OPEN AND CLOSE THE HOOD Two latches must be released to open the hood.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Next, move to the outside of the vehicle and push the safety catch to the left. The safety catch is located under the center front edge of the hood. WARNING! If the hood is not fully latched, it could fly up when the vehicle is moving and block your forward vision. You could have a collision. Be sure all hood latches are fully latched before driving. LIGHTS Hood Safety Catch Use the hood prop rod (if equipped) to secure the hood in the open position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 Dimmer Control The dimmer control is part of the headlight switch, and is located on the left side of the instrument panel. With the parking lights or headlights on, rotating the dimmer control upward will increase the brightness of the instrument panel lights. Overhead Console Interior Lights The interior lights come on when a door is opened.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE odometer, Electronic Vehicle Information Center — if equipped, and radio when the parking lights or headlights are on. Headlight Switch Multi-Function Lever The multi-function lever controls the operation of the turn signals, headlight beam selection, and passing lights. The lever is located on the left side of the steering column. The headlight switch is located on the left side of the instrument panel.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 Headlights, Parking Lights, Instrument Panel Lights Rotate the headlight switch clockwise to the first detent for parking light and instrument panel light operation. Turn to the second detent for headlight, park light and instrument panel light operation. Automatic Headlights – If Equipped This system automatically turns your headlights ON or OFF based on ambient light levels.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE SmartBeams — If Equipped The SmartBeam system provides increased forward lighting at night by automating high beam control through the use of a digital camera mounted on the inside rearview mirror. This camera detects vehicle specific light and automatically switches from high beams to low beams until the approaching vehicle is out of view. To Activate 1. Select “Automatic High Beams — ON” with the Electronic Vehicle Information Center (EVIC).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 Lights-on Reminder If the headlights or parking lights are on after the ignition is turned OFF, a chime will sound to alert the driver when the driver’s door is opened. Headlight Time Delay This feature provides the safety of headlight illumination for 90 seconds (programmable) when leaving your vehicle in an unlighted area. To activate the delay feature, turn off the ignition switch while the headlights are still on.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The message “Turn Signal On” will appear in the electronic vehicle information center (EVIC) — if equipped, and a continuous chime will be heard when the vehicle has been driven more than 1 mile (1.6 km) with either turn signal on. WINDSHIELD WIPERS AND WASHERS The wipers and washers are operated by the multi-function lever. The lever is located on the left side of the steering column.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 Rain Sensing Wipers—If Equipped This feature senses moisture on the windshield and automatically activates the wipers for the driver. The feature is especially useful for road splash or overspray from the windshield washers of the vehicle ahead. Rotate the end of the multi-function lever to one of six settings to activate this feature.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The rain sensing feature may not function properly when ice, or dried salt water is present on the windshield. • Use of Rain-X威 or products containing wax or silicone may reduce rain sensor performance. • A customer programmable feature in the Electronic Vehicle Information Center (EVIC) allows the Rain Sense feature to be turned off. Refer to “Personal Settings” in the Electronic Vehicle Information Center section of this manual for details.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 Windshield Wiper Operation Rotate the end of the lever to the second detent for Low speed wiper operation, or to the third detent for High speed operation. Intermittent Wiper System Use the intermittent wiper when weather conditions make a single wiping cycle, with a variable pause between cycles, desirable. Rotate the end of the lever to the first detent position, then turn the end of the lever to select the desired delay interval.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Headlight Washers — If Equipped This feature operates in combination with the windshield washers. To use the headlight washers, turn the headlights ON and press in on the windshield washer control knob while the engine is running. Headlight Washer Windshield Wiper/Washer Control This will operate the windshield washers and direct a timed high pressure spray onto the headlight lens.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 3 Headlight Washer Fluid Reservoir Tilt Steering Column Control TILT/TELESCOPING STEERING COLUMN Unlock the steering column by pulling out the handle located directly below the column. To tilt the column move the steering wheel up or down as desired. To lengthen or shorten the steering column pull out or push in the steering wheel. Lock the steering column in position by pushing the handle in until it fully engages.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE POWER TILT/TELESCOPING STEERING COLUMN — IF EQUIPPED The power tilt/telescoping steering column lever is located below the multi-function lever on the steering column. To tilt the column move the lever up or down as desired. To lengthen or shorten the steering column pull the lever toward you or push the lever away from you as desired.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 TRACTION CONTROL SYSTEM (TCS) — IF EQUIPPED WARNING! TCS cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded. The TCS cannot prevent accidents, including those resulting from excessive speed in turns, or hydroplaning. Only a safe, attentive, and skillful driver can prevent accidents.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To improve the vehicle’s traction when driving with snow chains, or starting off in deep snow, sand or gravel, switch off the TCS system by pressing the traction control switch. To turn the system back ON, press the traction control switch a second time until the traction control Indicator turns OFF. NOTE: • The traction control system comes on each time the ignition switch is turned ON. This will occur even if you used the switch to turn the system OFF.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 When the driver selects Reverse the system scans for objects behind the vehicle using four sensors located in the rear bumper. Objects can be detected from up to 71 inches (180 cm). A warning display above the rear window provides both visible and audible warnings indicating the range of the object. Rear Park Assist Indicator WARNING! Drivers must be careful when backing up even when using the Rear Park Assist System.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The Rear Park Assist System displays the outer most yellow LED’s at a slightly dimmer level to indicate that the system is ON. NOTE: When an audio tone is indicated by the Rear Park Assist display the system will MUTE the radio if it is turned on. The system can be turned on or off through the Electronic Vehicle Information Center (EVIC) when the vehicle is in PARK.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 WARNING! BAS cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded. The BAS cannot prevent accidents, including those resulting from excessive speed in turns, following another vehicle too closely, or hydroplaning. Only a safe, attentive, and skillful driver can prevent accidents.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE The ESP enhances directional control and reduces driving wheel spin of the vehicle under various driving conditions. The system operates when the vehicle speed is greater than 7.8 mph (12.6 km/h). To improve the vehicle’s traction when driving with snow chains, or starting off in deep snow, sand or gravel, switch off the ESP system by pressing the ESP switch.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 wheel slip control is active at vehicle speeds between approximately 24 mph (40 km/h) and 50 mph (80 km/h). CAUTION! ELECTRONIC SPEED CONTROL When engaged, this device takes over the accelerator operation at speeds greater than 25 mph (40 km/h). The speed control switch consists of a stalk mounted lever located on the steering column.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Activate: Push and release the speed control lever (“ON/ OFF”) once and the electronic speed control indicator light in the instrument cluster will illuminate indicating that the electronic speed control is ON. To turn the system OFF, Push and release the lever (“ON/OFF”) again and the system and indicator will turn off. To Set At A Desired Speed: When the vehicle has reached the desired speed, pull the lever toward you and release.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 To decrease speed while speed control is set, push the lever down and hold (“COAST”). Release the lever when the desired speed is reached, and the new speed will be set. Pushing down and releasing the lever (“COAST”) once will result in a 1 mph (2 km/h) speed decrease. Each time the lever is pushed down and released, speed decreases. To Accelerate For Passing: Depress the accelerator as you would normally.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE OVERHEAD CONSOLE — IF EQUIPPED The overhead console contains courtesy/reading lights, an optional universal garage door opener (HomeLink威), storage for sunglasses, and an optional power sunroof switch. Courtesy/Reading Lights At the forward end of the console are two courtesy/ reading lights. Press the lens to turn these lights on. Press a second time to turn the lights off. The lights also turn on when a front door or rear door is opened.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 GARAGE DOOR OPENER — IF EQUIPPED The HomeLink威 Universal Transceiver replaces up to three remote controls (hand held transmitters) that operate devices such as garage door openers, motorized gates, or home lighting. It triggers these devices at the push of a button. The Universal Transceiver operates off your vehicle’s battery and charging system; no batteries are needed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Programming HomeLink NOTE: When programming a garage door opener, it is advised to park outside the garage. It is also recommended that a new battery be placed in the hand-held transmitter of the device being programmed to HomeLink for quicker training and accurate transmission of the radio-frequency signal. The Electronic Vehicle Information Center (EVIC) features a driver-interactive display which includes HomeLink system messages.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 NOTE: Some gate operators and garage door openers may require you to replace this Programming Step 3 with procedures noted in the ⬙Gate Operator/Canadian Programming⬙ section. 4. The EVIC display will show “Channel X Training” (where X is Channel 1, 2, or 3). Release both buttons after the EVIC display shows “Channel X Trained”. NOTE: If the EVIC display shows “Did Not Train” repeat steps 2–4. HomeLink Buttons 2.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE door opener may have a multiple security code system (rolling code system). Please proceed to steps 6–8 to complete the programming of a rolling code equipped device (most common garage door openers require this step. 6. At the garage door opener receiver (motor-head unit) in the garage, locate the ⬙learn⬙ or ⬙smart⬙ button. This can usually be found where the hanging antenna wire is attached to the motor-head unit. 7.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 3. Continue to press and hold the HomeLink button while you press and release every two seconds (⬙cycle⬙) your hand-held transmitter until the frequency signal has successfully been accepted by HomeLink. The EVIC display will show “Channel X Trained” (where X is Channel 1, 2, or 3). Proceed with ⬙Programming⬙ step four to complete.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Security If you sell your vehicle, be sure to erase the frequencies by following the “Erasing HomeLink Buttons” instructions in this section. POWER SUNROOF — IF EQUIPPED The power sunroof switch is located between the sun visors on the overhead console. This device complies with part 15 of FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 WARNING! • Never leave children in a vehicle, with the keys in the ignition switch. Occupants, particularly unattended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death. • In an accident, there is a greater risk of being thrown from a vehicle with an open sunroof. You could also be seriously injured or killed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Pinch Protect Override If a known obstruction (ice, debris, etc.) prevents closing, press the switch forward and hold for two seconds after the reversal occurs. This allows the sunroof to move towards the closed position. NOTE: Pinch protection is disabled while the switch is pressed. Venting Sunroof - Express Press and release the ⬙V⬙ button, and the sunroof will open to the vent position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 Ignition Off Operation For vehicles not equipped with the Electronic Vehicle Information Center (EVIC), the power sunroof switch will remain active for 10 minutes after the ignition switch is turned off. Opening either front door will cancel this feature. For vehicles equipped with the EVIC, the power sunroof switch will remain active for up to 60 minutes after the ignition switch is turned off. Opening either front door will cancel this feature.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: If desired, the power outlet next to the ash receiver tray (if equipped) can be converted by your authorized dealer to provide power with the ignition switch in the LOCK position. The center console outlet is powered directly from the battery (power available at all times). Items plugged into this outlet may discharge the battery and/or prevent engine starting.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 Electrical Outlet Use With Engine Off CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e. cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting. • Accessories that draw higher power (i.e. coolers, vacuum cleaners, lights, etc.), will degrade the battery even more quickly.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Front Seat Cup Holders — 300 Touring and 300C Models The cup holders are located in the forward edge of the center console. Push down on the cover as shown to expose the cup holders. Close the cover when the cup holders are no longer needed. Front Seat Cup Holders Rear Seat Cup Holders The rear seat cup holders are located in the center armrest between the rear seats.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 STORAGE Console Features The center console contains a large storage bin. The storage bin contains a four-slot coin holder (designed to hold various size coins) and a rubber mat at the bottom of the bin for noise control. The bin is large enough to hold a portable AC/DC converter to power laptops, games, or other electrical equipment.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Always place cargo evenly on the cargo floor. Put heavier objects as low and as far forward as possible. • Place as much cargo as possible in front of the rear axle. Too much weight or improperly placed weight over or behind the rear axle can cause the rear of the vehicle to sway. • Do not pile luggage or cargo higher than the top of the seatback. This could impair visibility or become a dangerous projectile in a sudden stop or collision.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 Instruments And Controls . . . . . . . . . . . . . . . . 140 䡵 Standard Instrument Cluster . . . . . . . . . . . . . . 141 䡵 Premium Instrument Cluster . . . . . . . . . . . . . . 142 䡵 Instrument Cluster Descriptions . . . . . . . . . . . 143 䡵 Electronic Vehicle Information Center (EVIC) . . 150 ▫ Personal Settings (Customer Programmable Features) . . . . . . . . . . . . . . . . . . . . . . . . . . . 158 䡵 Setting The Analog Clock . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Operating Instructions - Radio Mode . . . . . . . 165 ▫ Changing Tape Direction . . . . . . . . . . . . . . . . 176 ▫ Operation Instructions - CD Mode . . . . . . . . . 168 ▫ Metal Tape Selection . . . . . . . . . . . . . . . . . . . 176 ▫ Operation Instructions - Auxiliary Mode . . . . . 169 ▫ Pinch Roller Release . . . . . . . . . . . . . . . . . . . 176 ▫ Operating Instructions - Hands Free Phone — If Equipped . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 139 ▫ Selecting a Channel . . . . . . . . . . . . . . . . . . . . 184 ▫ Satellite Radio Operation . . . . . . . . . . . . . . . . 191 ▫ Storing And Selecting Pre-Set Channels . . . . . . 185 䡵 Cassette Tape And Player Maintenance . . . . . . 191 ▫ Using The PTY (Program Type) Button (If Equipped) . . . . . . . . . . . . . . . . . . . . . . . . 185 䡵 CD/DVD Disc Maintenance . . . . . . . . . . . . . . 192 ▫ PTY Button ⬙Scan⬙ . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENTS AND CONTROLS
UNDERSTANDING YOUR INSTRUMENT PANEL 141 STANDARD INSTRUMENT CLUSTER 4
UNDERSTANDING YOUR INSTRUMENT PANEL PREMIUM INSTRUMENT CLUSTER
UNDERSTANDING YOUR INSTRUMENT PANEL 143 INSTRUMENT CLUSTER DESCRIPTIONS 1. Electronic Speed Control Indicator Light — If Equipped This light will illuminate when the electronic speed control is ON. 5. Speedometer Indicates vehicle speed. 6. Electronic Vehicle Information Center Display When the appropriate conditions exist, this display shows the Electronic Vehicle Information Center (EVIC) messages. (See page 150 for more information.) (only on vehicles equipped with steering wheel mounted switches). 2.
UNDERSTANDING YOUR INSTRUMENT PANEL 9. Anti-Lock Brake Light This light monitors the Anti-Lock Brake System. The light will turn on when the ignition switch is turned to the ON position and may stay on for as long as four seconds. If the ABS light remains on or turns on while driving, it indicates that the Anti-Lock portion of the brake system is not functioning and that service is required. However, the conventional brake system will continue to operate normally if the BRAKE warning light is not on.
UNDERSTANDING YOUR INSTRUMENT PANEL 145 The dual brake system provides a reserve braking capacity in the event of a failure to a portion of the hydraulic system. Failure of either half of the dual brake system is indicated by the Brake Warning Light which will turn on when the brake fluid level in the master cylinder has dropped below a specified level. The light will remain on until the cause is corrected.
UNDERSTANDING YOUR INSTRUMENT PANEL 13. Electronic Stability Program (ESP) Indicator Light/Traction Control System (TCS) Indicator Light — If Equipped If this indicator light flashes during acceleration, apply as little throttle as possible. While driving, ease up on the accelerator. Adapt your speed and driving to the prevailing road conditions, and do not switch off the ESP, or TCS — if equipped. (See page 117 for more information.) 14.
UNDERSTANDING YOUR INSTRUMENT PANEL 147 15. Trip Odometer Button Trip Odometer Button — Standard Cluster The word ⬙TRIP⬙ will appear when this button is pressed. Push in and hold the button for two seconds when the trip odometer is displayed to reset it to 0 miles or kilometers. A second press of the button will display the outside temperature in the odometer. Trip Odometer Button — Premium Cluster Press this button to change the display from odometer to either of the two trip odometer settings.
UNDERSTANDING YOUR INSTRUMENT PANEL 21. Electronic Throttle Control (ETC) Light This light informs you of a problem with the Electronic Throttle Control system. If a problem is detected the light will come on while the engine is running. Cycle the ignition key when the vehicle has completely stopped and the gear selector is placed in the PARK position. The light should turn off.
UNDERSTANDING YOUR INSTRUMENT PANEL 149 Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale. 23. Voltage Light This light monitors the electrical system voltage. The light should turn on momentarily as the engine is started.
UNDERSTANDING YOUR INSTRUMENT PANEL ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) • Vehicle information warning message displays • Tire Pressure Monitor System (if equipped) • Personal Settings (customer programmable features) • Compass display • Outside temperature display • Trip computer functions • UConnect™ hands-free communication system displays (if equipped) • Navigation system screens (if equipped) • Audio mode display Electronic Vehicle Information Center The Electronic Vehicle Information C
UNDERSTANDING YOUR INSTRUMENT PANEL 151 Press the FUNCTION SELECT button to accept a selection. The FUNCTION SELECT button also advances the radio to the next preset FUNC- station, changes the side of the tape being TION played (if so equipped), or changes the current SELECT CD track being played (if so equipped) when Button the EVIC is in the Compass/Temp/Audio screen.
UNDERSTANDING YOUR INSTRUMENT PANEL • Memory System Disabled – Vehicle Not In Park (with a single chime) • Memory System Disabled – Seat Belt Buckled (with a single chime) • Personal Settings Not Available – Vehicle Not in Park • Left/Right Front Door Ajar (one or more, with a single chime if speed is above 1 mph) • Left/Right Rear Door Ajar (one or more, with a single chime if speed is above 1 mph) • Door(s) Ajar (with a single chime if vehicle is in motion) • Trunk Ajar (with a single chime) • Low Wa
UNDERSTANDING YOUR INSTRUMENT PANEL 153 • Check Gascap (refer to “Adding Fuel” in Section 5 of this manual for more details) The Trip Functions mode displays the following information: • Service Park Assist System (with a single chime) • Average Fuel Economy Shows the average fuel economy since the last reset. When the fuel economy is reset, the display will read “RESET” or show dashes for two seconds.
UNDERSTANDING YOUR INSTRUMENT PANEL • When the DTE value is less than 30 miles (48 km) estimated driving distance, the DTE display will change to a text display of ⬙LOW FUEL.⬙ This display will continue until the vehicle runs out of fuel. Adding a significant amount of fuel to the vehicle will turn off the ⬙LOW FUEL⬙ text and a new DTE value will display. • Trip A Shows the total distance travelled for trip A since the last reset.
UNDERSTANDING YOUR INSTRUMENT PANEL 155 Manual Compass Calibration If the compass appears erratic and the “CAL” message does not appear in the EVIC display, you must put the compass into the Calibration Mode manually as follows: To put into a Calibration Mode: Turn on the ignition switch. Then, press and hold the compass button for approximately 2 seconds. Then, press the SCROLL button until “Calibrate Compass” displays in the EVIC.
UNDERSTANDING YOUR INSTRUMENT PANEL To set the variance: Turn the ignition switch ON. Then, press and hold the compass button for approximately 2 seconds. Then, press the SCROLL button until “Compass Variance” displays in the EVIC. Both the “Compass Variance” message and the last variance zone number will display in the EVIC. Then, press and release FUNCTION SELECT button until the proper variance zone is selected according to the map. Finally, press and release the compass button to exit.
UNDERSTANDING YOUR INSTRUMENT PANEL 157 The EVIC displays this symbol to indicate that you have voice mail. Voice Mail The EVIC displays this symbol to indicate a text message. The EVIC displays this symbol to indicate that the UConnect™ phone is currently not available. Phone Not Available Navigation — If Equipped Text Message The EVIC displays this symbol to indicate the battery strength of the UConnect™ phone.
UNDERSTANDING YOUR INSTRUMENT PANEL Turn By Turn Directions The EVIC displays turn-by-turn directions to a programmed destination when Turn by Turn Navigation is enabled through Personal Settings. When enabled, the EVIC displays the name of the approaching road at the top of the screen, followed by an arrow to indicate the direction to turn the vehicle, and a count down to indicate the distance to the turn. NOTE: Refer to your “Navigation User’s Manual” for detailed operating instructions.
UNDERSTANDING YOUR INSTRUMENT PANEL 159 “Remote Key Unlock” When Driver Door 1st Press is selected, only the driver’s door will unlock on the first press of the remote keyless entry unlock button. When Driver Door 1st Press is selected, you must press of the remote keyless entry unlock button twice to unlock the passenger’s doors. When All Doors 1st Press is selected, all of the doors will unlock on the first press of the remote keyless entry unlock button.
UNDERSTANDING YOUR INSTRUMENT PANEL “Delay Power Off to Accessories Until Exit” When this feature is selected, the power window switches, radio, hands–free system (if equipped), DVD video system (if equipped), power sunroof (if equipped), and power outlets will remain active for up to 60 minutes after the ignition switch is turned off. Opening a vehicle door will cancel this feature. To make your selection, press and release the FUNCTION SELECT button until “Off,” “45 sec.,” “5 min.,” “10 min.
UNDERSTANDING YOUR INSTRUMENT PANEL 161 “Rain Sensing Intermittent Wipers” — If Equipped When ON is selected, the system will automatically activate the windshield wipers if it senses moisture on the windshield. To make your selection, press and release the FUNCTION SELECT button until “ON” or “OFF” appears. When OFF is selected, the system reverts to the standard intermittent wiper operation.
UNDERSTANDING YOUR INSTRUMENT PANEL “Headlights On With Wipers” (Available with Auto Headlights Only) When ON is selected, and the headlight switch is in the AUTO position, the headlights will turn on approximately 10 seconds after the wipers are turned on. The headlights will also turn off when the wipers are turned off if they were turned on by this feature. To make your selection, press and release the FUNCTION SELECT button until “ON” or “OFF” appears.
UNDERSTANDING YOUR INSTRUMENT PANEL 163 RADIO GENERAL INFORMATION Radio Broadcast Signals Your new radio will provide excellent reception under most operating conditions. Like any system, however, car radios have performance limitations, due to mobile operation and natural phenomena, which might lead you to believe your sound system is malfunctioning.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: For vehicles equipped with the Electronic Vehicle Information Center (EVIC), the radio, steering wheel radio controls (if equipped), and 6 disc CD/DVD changer (if equipped) will remain active for up to 60 minutes after the ignition switch is turned off. Opening either front door will cancel this feature. The time is programmable through the Electronic Vehicle Information Center (EVIC).
UNDERSTANDING YOUR INSTRUMENT PANEL 165 Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Control (Rotary) Press the ON/VOL control to turn the radio ON. Press the ON/VOL a second time to turn OFF the radio. Electronic Volume Control The electronic volume control turns continuously (360 degrees) in either direction without stopping.
UNDERSTANDING YOUR INSTRUMENT PANEL equipped) frequencies, pausing for 5 seconds at each listenable station before continuing to the next. To stop the search, press SCAN a second time. PSCAN Button (Radio Mode) Pressing the PSCAN button, causes the tuner to scan through preset stations, in either AM, FM or Satellite (if equipped) frequencies, pausing for 5 seconds at each preset station before continuing to the next. To stop the search, press PSCAN a second time.
UNDERSTANDING YOUR INSTRUMENT PANEL 167 Press the rotary TUNE control a third time and TREB will be displayed. Turn the TUNE control to the right or left to increase or decrease the Treble tones. selected within 5 seconds after pressing the SET button, the station will continue to play but will not be stored into push-button memory. Press the rotary TUNE control a fourth time and BAL will be displayed.
UNDERSTANDING YOUR INSTRUMENT PANEL Operation Instructions - CD Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Inserting The Compact Disc (Single CD Player) Gently insert one CD into the CD player with the CD label facing up. The CD will automatically be pulled into the CD Player and the CD icon will illuminate on the radio display. If the volume control is ON, the unit will switch to CD mode and begin to play.
UNDERSTANDING YOUR INSTRUMENT PANEL 169 TIME Button (CD Mode) Press this button to change the display from elapsed CD playing time to time of day. The time of day will be displayed for 5 seconds. RW/FF (CD Mode) Press and hold the FF (Fast Forward) and the CD player will begin to fast forward until FF is released. The RW (Reverse) button works in a similar manner. RND/SET Button (Random Play Button) (CD Mode) Press this button while the CD is playing to activate Random Play.
UNDERSTANDING YOUR INSTRUMENT PANEL MUTE Button (Auxiliary Mode) Press the MUTE button to cancel the sound from the speakers. ⬙MUTE⬙ will be displayed. Press the MUTE button a second time and the sound from the speakers will return. Rotating the volume control or turning OFF the ignition will also return the sound from the speakers. SCAN Button (Auxiliary Mode) No function. EJECT Button (Auxiliary Mode) No function. PSCAN Button (Auxiliary Mode) No function.
UNDERSTANDING YOUR INSTRUMENT PANEL 171 SALES CODE RAK – AM/FM/CASSETTE/CD (6-DISC) RADIO WITH OPTIONAL SATELLITE RADIO, HANDS FREE PHONE, VIDEO, MP3, and WMA CAPABILITIES NOTE: The radio sales code is located on the lower right side of your radio faceplate. Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Control (Rotary) Press the ON/VOL control to turn the radio ON.
UNDERSTANDING YOUR INSTRUMENT PANEL SEEK Button (Radio Mode) Press and release the SEEK button to search for the next station in either AM/FM or Satellite (if equipped) mode. Press the right side of the button to seek up and the left side to seek down. The radio will remained tuned to the new station until you make another selection. Holding the button and will bypass stations without stopping until you release it.
UNDERSTANDING YOUR INSTRUMENT PANEL 173 RW/FF (Radio Mode) Pressing the rewind/fast forward button causes the tuner to search for the next frequency in the direction of the arrows. This feature operates in either AM, FM or Satellite (if equipped) frequencies. TUNE Control (Radio Mode) Turn the right side rotary control to increase or decrease the frequency. AM/FM Button (Radio Mode) Press the button to select AM or FM Modes.
UNDERSTANDING YOUR INSTRUMENT PANEL Turn the tune knob to select the following format types: Program Type No program type or undefined News Information Sports Talk Rock Classic Rock Adult Hits Soft Rock Top 40 Country Oldies Soft Nostalgia Jazz Classical Rhythm and Blues 16 Digit-Character Display None News Information Sports Talk Rock Classic_Rock Adult_Hits Soft_Rock Top_40 Country Oldies Soft Nostalgia Jazz Classical Rhythm_and_Blues Soft Rhythm and Blues Foreign Language Religious Music Religious
UNDERSTANDING YOUR INSTRUMENT PANEL 175 Buttons 1 - 6 (Radio Mode) These buttons tune the Radio to the stations that you commit to push-button memory {12 AM, 12 FM, and 12 Satellite (if equipped) stations}. Operating Instructions — Tape Player Insert the cassette with the exposed tape side toward the left and the mechanical action of the player will gently pull the cassette into the play position.
UNDERSTANDING YOUR INSTRUMENT PANEL Changing Tape Direction If you wish to change the direction of tape travel (side being played), press Preset 6. The lighted arrow in the display window will show the new direction. * ”Dolby” noise reduction manufactured under license from Dolby Laboratories Licensing Corporation. Dolby and the double-D symbol are trademarks of Dolby Laboratories Licensing Corporation.
UNDERSTANDING YOUR INSTRUMENT PANEL 177 Inserting Compact Disc(s) CAUTION! SCAN Button (CD MODE for CD Audio Play) Press the Scan button to scan through each track on the CD currently playing. LOAD/EJECT Button (CD Mode for CD Audio Play) This CD player will accept 4 3/4 inch (12 cm) discs only. The use of other sized discs may damage the CD player mechanism. You may eject a disc with the radio OFF.
UNDERSTANDING YOUR INSTRUMENT PANEL Press and hold the LOAD/EJT button for 5 seconds and all CDs will be ejected from the radio. If you have ejected a disc and have not removed it within 15 seconds, it will be reloaded. If the CD is not removed, the radio will continue to play the non-removed CD. If the CD is removed and there are other CD’s in the radio, the radio will play the next CD after a 2 minute timeout.
UNDERSTANDING YOUR INSTRUMENT PANEL 179 Press the RND button a second time to stop Random Play. Buttons 1 - 6 (CD MODE for CD Audio Play) Selects disc positions 1 - 6 for Play/Load/Eject. Notes On Playing MP3 Files The radio can play MP3 files, however, acceptable MP3 file recording media and formats are limited. When writing MP3 files, pay attention to the following restrictions. Supported Media (Disc Types) The MP3 file recording media supported by the radio are CD-ROM, CD-R and CD-RW.
UNDERSTANDING YOUR INSTRUMENT PANEL Supported MP3 File Formats The radio will recognize only files with the *.mp3 extension as MP3 files. Non-MP3 files named with the *.mp3 extension may cause playback problems. The radio is designed to recognize the file as an invalid MP3 and will not play the file. When using the MP3 encoder to compress audio data to an MP3 file, the bit rate and sampling frequencies in the following table are supported. In addition, variable bit rates (VBR) are also supported.
UNDERSTANDING YOUR INSTRUMENT PANEL 181 To increase the speed of disc loading, it is recommended to use CD-R media and single-session discs. To create a single-session disc, enable the Disc at Once option before writing to the disc. Operation Instructions - (CD Mode for MP3 and WMA Audio Play) SEEK Button (CD Mode for MP3 and WMA Play) Pressing the right side of the SEEK button plays the next file. Pressing the left side of the SEEK button plays the beginning of the file.
UNDERSTANDING YOUR INSTRUMENT PANEL INFO Button (CD Mode for MP3 Play) Press and INFO button while playing MP3 or WMA disc. The radio scrolls through the following TAG information: Song Title, Artist, File Name, and Folder Name (if available). Press the INFO button once more to return to ⬙elapsed time⬙ priority mode. Press and hold the INFO button while in the message display priority mode or elapsed time display priority mode will display the song title for each file.
UNDERSTANDING YOUR INSTRUMENT PANEL 183 Operating Instructions - Video Entertainment System (VES) (If Equipped) Refer to separate “Video Entertainment System (VES) Guide.” SATELLITE RADIO — IF EQUIPPED Satellite radio uses direct satellite to receiver broadcasting technology to provide clear digital sound, coast to coast. The subscription service provider is Sirius™ Satellite Radio.
UNDERSTANDING YOUR INSTRUMENT PANEL ESN/SID Access With RAQ and RAK Radios With the ignition switch in the ACCESSORY position and the radio OFF, press the CD Eject and TIME buttons simultaneously for 3 seconds. All twelve ESN/SID numbers will be displayed. The radio will exit the ESN/SID mode when any other button is pushed, the ignition is turned OFF, or 5 minutes has passed since any button was pushed. ESN/SID Access With REC Navigation Radios Please refer to your Navigation User’s Manual.
UNDERSTANDING YOUR INSTRUMENT PANEL 185 NOTE: Channels that may contain objectionable content can be blocked. Contact Sirius Customer Care at 888-539-7474 to discuss options for channel blocking or unblocking. Please have your ESN/SID information available. NOTE: Pressing the ⬙SEEK⬙ or ⬙SCAN⬙ button while performing a music type scan will change the channel by one and stop the search. Pressing a pre-set memory button during a music type scan, will call up the memory channel and stop the search.
UNDERSTANDING YOUR INSTRUMENT PANEL Reception Quality Satellite reception may be interrupted due to one of the following reasons. • The vehicle is parked in an underground parking structure or under a physical obstacle. • Dense tree coverage may interrupt reception in the form of short audio mutes.
UNDERSTANDING YOUR INSTRUMENT PANEL 187 4 Raising The DVD Screen Remote Control Location
UNDERSTANDING YOUR INSTRUMENT PANEL NAVIGATION SYSTEM (SALES CODE REC) — IF EQUIPPED NOTE: The radio sales code is located on the lower right side of your radio faceplate. Navigation Radio with CD Player and MP3 Capability (REC) - combines a Global-Positioning System-based navigation system with a color screen to provide maps, turn identification, selection menus and instructions for selecting a variety of destinations and routes.
UNDERSTANDING YOUR INSTRUMENT PANEL 189 REMOTE SOUND SYSTEM CONTROLS The remote sound system controls are located on the surface of the steering wheel at the 3 and 9 o’clock positions. VOLUME Button The VOLUME button controls the sound level of the sound system. Press the top of the VOLUME button to increase the sound level. Press the bottom of the VOLUME button to decrease the sound level. Press the AUDIO MODE button to select the Compass/Temp/Audio screen.
UNDERSTANDING YOUR INSTRUMENT PANEL When the EVIC is in the Compass/Temp/ Audio screen, press the FUNCTION SELECT button to advance the radio to the next preset FUNC- station, to change the side of the tape being TION played (if so equipped), or to change the curSELECT rent CD track being played (if so equipped). Button Tape Player Operation Press the top of the SCROLL button once to listen to the next track on the cassette.
UNDERSTANDING YOUR INSTRUMENT PANEL 191 Press either the top or bottom of the SCROLL button twice to listen to the second track on the CD, three times to listen to the third track, and so forth. Satellite Radio Operation Press the top of the SCROLL button once to SEEK the next listenable station up from the current setting. Press the bottom of the SCROLL button once to SEEK the next listenable station down from the current setting.
UNDERSTANDING YOUR INSTRUMENT PANEL CD/DVD DISC MAINTENANCE To keep the CD/DVD discs in good condition, take the following precautions: 1. Handle the disc by its edge; avoid touching the surface. 2. If the disc is stained, clean the surface with a soft cloth, wiping from center to edge. 3. Do not apply paper, paper CD labels, or tape to the disc; avoid scratching the disc. 4. Do not use solvents such as benzine, thinner, cleaners, or antistatic sprays. 5. Store the disc in its case after playing. 6.
UNDERSTANDING YOUR INSTRUMENT PANEL 193 The instrument panel features four dual-vane airflow registers. Two registers are located on the outer ends of the instrument panel and two are located in the center of the instrument panel. These registers can be closed to partially block airflow. second time to turn off the air conditioning. The button includes an LED that illuminates when compressor operation is selected.
UNDERSTANDING YOUR INSTRUMENT PANEL Blower Control Mode Selection The rotary knob on the left controls the blower and can be set in one of four speeds and OFF. The blower fan motor will remain on until the system is turned to the OFF position or the ignition is turned OFF. The mode selector (the right rotary knob) can be placed in several positions. Dots between each of the mode selections identify intermediate modes that allow the occupants to fine tune airflow distribution.
UNDERSTANDING YOUR INSTRUMENT PANEL 195 Defrost/Floor Air flows through the front and rear floor outlets and the outlets at the base of the windshield. Air is also directed to the front door windows through the side window demister grilles. Floor Air flows through the floor outlets located under the instrument panel and into the rear seating area through vents under the front seats. Bi-Level Air flows both through the outlets located in the instrument panel and those located on the floor.
UNDERSTANDING YOUR INSTRUMENT PANEL Automatic Temperature Control — If Equipped The Infrared Dual-Zone Climate Control System automatically maintains the interior comfort level desired by the driver and passenger. This is accomplished by a dual sun-sensor in the top of the instrument panel, and an infrared sensor located in the face of the control unit.
UNDERSTANDING YOUR INSTRUMENT PANEL 197 Operation of the system is quite simple. Begin by turning the right mode knob to AUTO, and place the blower control (left knob) to either LO AUTO or HI AUTO. The LO AUTO position should be used for front seat occupants only. The HI AUTO position should be used when more air flow is desired, or when rear seat occupants are present. Dial in the temperature you would like the system to maintain by rotating the driver’s or passenger’s control knob.
UNDERSTANDING YOUR INSTRUMENT PANEL • Most of the time, when in Automatic operation, you can temporarily put the system into recirculation mode by pressing the Recirc button. However, under certain conditions in automatic the system is blowing air out of the defrost vents. When these conditions are present and the Recirc button is pressed the indicator will flash and remain off. This tells you that you are unable to go into recirculation mode at this time.
UNDERSTANDING YOUR INSTRUMENT PANEL 199 4
UNDERSTANDING YOUR INSTRUMENT PANEL The operator can override the AUTO mode setting and select the direction of the air by rotating the right mode knob to one of the following positions. floor. Air flows through the registers in the back of the center console to the rear seat passengers. These registers can be closed to block airflow. • Defrost Air is directed to the windshield through the outlets at the base of the windshield.
UNDERSTANDING YOUR INSTRUMENT PANEL 201 the rear window defroster is ON. The defroster automatically turns off after approximately 10 minutes of operation for the first push of the button, and will turn off after approximately 5 minutes for the second push of the button. CAUTION! To avoid damaging the electrical conductors of the rear window defroster, do not use scrapers, sharp instruments, or abrasive window cleaners on the interior surface of the window.
UNDERSTANDING YOUR INSTRUMENT PANEL Winter Operation Use of the air Recirculation mode during winter months is not recommended because it may cause window fogging. NOTE: See Operating Tips chart (for Manual A/C Control) at the end of this section for suggested control settings in different weather conditions. Vacation Storage Anytime you store your vehicle, or keep it out of service (i.e.
UNDERSTANDING YOUR INSTRUMENT PANEL 203 Operating Tips 4
STARTING AND OPERATING CONTENTS 䡵 Starting Procedures . . . . . . . . . . . . . . . . . . . . 208 ▫ Anti-Lock Brake System . . . . . . . . . . . . . . . . 225 ▫ Normal Starting . . . . . . . . . . . . . . . . . . . . . . 208 䡵 Power Steering . . . . . . . . . . . . . . . . . . . . . . . . 228 䡵 Engine Block Heater — If Equipped . . . . . . . . 210 䡵 Multi Displacement System (MDS) 5.7L Engine Only . . . . . . . . . . . . . . . . . . . . . . 229 䡵 Transmission Shifting . . . . . . . . . . . . . . . . .
STARTING AND OPERATING ▫ Tire Identification Number (TIN) . . . . . . . . . . 238 䡵 Fuel Requirements . . . . . . . . . . . . . . . . . . . . . 253 ▫ Tire Loading And Tire Pressure . . . . . . . . . . . 239 ▫ 2.7L Engines . . . . . . . . . . . . . . . . . . . . . . . . . 253 䡵 Tires—General Information . . . . . . . . . . . . . . . 243 ▫ 3.5L And 5.7L Engines . . . . . . . . . . . . . . . . . . 253 ▫ Tire Pressure . . . . . . . . . . . . . . . . . . . . . . . . . 243 ▫ Spark Knock . . . . . . .
STARTING AND OPERATING 207 ▫ Overloading . . . . . . . . . . . . . . . . . . . . . . . . . 261 ▫ Towing Requirements . . . . . . . . . . . . . . . . . . 267 ▫ Loading . . . . . . . . . . . . . . . . . . . . . . . . . . . . 261 ▫ Towing Tips . . . . . . . . . . . . . . . . . . . . . . . . . 271 䡵 Trailer Towing . . . . . . . . . . . . . . . . . . . . . . . . 262 䡵 Recreational Towing (Behind Motorhome, Etc.) . . . . . . . . . . . . . . . . 272 ▫ Common Towing Definitions . . . . . . . . . . . . .
STARTING AND OPERATING STARTING PROCEDURES CAUTION! Long periods of engine idling, especially at high engine speeds, can cause excessive exhaust temperatures which can damage your vehicle. Do not leave your vehicle unattended with the engine running. WARNING! Do not leave animals or children inside parked vehicles in hot weather; interior heat build up may cause serious injury or death. The gear selector must be in the NEUTRAL or PARK position before you can start the engine.
STARTING AND OPERATING 209 WARNING! • Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transmission cannot be started this way. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle. If the vehicle has a discharged battery, booster cables may be used to obtain a start from a booster battery or the battery in another vehicle. This type of start can be dangerous if done improperly.
STARTING AND OPERATING After Starting The idle speed will automatically decrease as the engine warms up. TRANSMISSION SHIFTING 4 Speed Automatic Transmission ENGINE BLOCK HEATER — IF EQUIPPED The engine block heater warms engine coolant and permits quicker starts in cold weather. Connect the cord to a standard 110-115 volt AC electrical outlet with a grounded, three-wire extension cord. The engine block heater cord is routed under the hood on the driver side of the vehicle.
STARTING AND OPERATING 211 WARNING! It is dangerous to shift the selector lever out of “P” or “N” if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in reverse. You could lose control of the vehicle and hit someone or something. Only shift into gear when the engine is idling normally and when your right foot is firmly on the brake pedal.
STARTING AND OPERATING The following indicators should be used to ensure that you have engaged the transmission shift lever into the P (Park) position: • When shifting into P (Park) move the lever all the way forward until it stops, and is fully seated. • Look at the shift indicator display on the instrument panel to ensure it is in the P (Park) position. CAUTION! Before moving the shift lever out of P (Park), you must turn the ignition from LOCK to ON so the shift lever is released.
STARTING AND OPERATING 213 Overdrive and shifting operation will resume when the temperature of the transmission reaches the appropriate temperature. Refer to the “Note” under “Torque Converter Clutch” later in this section. If the transmission temperature gets too hot, the transmission may downshift out of Overdrive or engage overdrive at higher vehicle speeds until the transmission cools down. After cooldown, Overdrive will resume normal operation. 3 (Third) This range eliminates shifts into Overdrive.
STARTING AND OPERATING Torque Converter Clutch A feature designed to improve fuel economy has been added to the automatic transmission of this vehicle. A clutch within the torque converter engages automatically at calibrated speeds. This may result in a slightly different feeling or response during normal operation in high gear. When the vehicle speed drops or during acceleration, the clutch automatically and smoothly disengages.
STARTING AND OPERATING 215 NOTE: Even if the transmission can be reset, we recommend that you visit a dealer at your earliest possible convenience. Your dealer has diagnostic equipment to determine if the problem could recur. If the transmission cannot be reset, dealer service is required. 5 Speed Automatic Transmission Gear Selector WARNING! Unintended movement of a vehicle could injure those in and near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running.
STARTING AND OPERATING Park Position The PARK position is to be used when parking the vehicle. Engage only with the vehicle stopped. The PARK position is not intended to serve as a brake when the vehicle is parked. Rather, the driver should always use the parking brake in addition to placing the selector lever in PARK to secure the vehicle. ON positions. Remove the rubber storage tray from the bin located to the right of the shifter lever.
STARTING AND OPERATING 217 Neutral No power is transmitted from the engine to the drive axle. When the brakes are released, the vehicle can be moved freely (pushed or towed). Do not engage in NEUTRAL position while driving except to coast when the vehicle is in danger of skidding (e.g., on icy roads). The engine may be started in this range. Use this range for starting your vehicle if it is moving or being towed.
STARTING AND OPERATING NOTE: To avoid overrevving the engine when the selector lever is moved in “D -” direction, the transmission will not shift to a lower gear if the engine’s revolutions per minute limit would be exceeded. Briefly press the selector lever in the “D +” direction. The transmission will shift from the current gear to the next higher gear. Press and hold the selector lever in the “D +” direction. The transmission will shift from the current gear directly to gear “D”.
STARTING AND OPERATING 219 A reset feature is available to allow the vehicle to be driven to a dealer for service. To reset the transmission, use the following procedure: 1. Stop the vehicle. 2. Move the selector lever to the PARK position. 3. Turn off the engine. 4. Wait approximately 10 seconds. 5. Restart the engine. 6. Move the shift lever to the desired range. If the problem is no longer detected, the transmission will return to normal operation.
STARTING AND OPERATING Automatic Transmission — General Information CAUTION! Damage to the transmission may occur if the following precautions are not observed: • Shift into PARK only after the vehicle has come to a complete stop. • Shift into or out of REVERSE only after the vehicle has come to a complete stop and the engine is at idle speed. • Do not shift from REVERSE, PARK or NEUTRAL into any forward gear when the engine is above idle speed.
STARTING AND OPERATING 221 • If there is a need to restart your engine be sure to cycle the key to the LOCK position before restarting. Transmission engagement may be delayed up to 10 seconds after restart if the key is not cycled to the LOCK position first. • The electronically controlled transmission provides a precise shift schedule. The transmission electronics are self-calibrating. Therefore, the first few shifts on a new vehicle may be somewhat abrupt or soft until after the break-in period.
STARTING AND OPERATING To rock a vehicle out of soft ground (mud or snow), alternately shift from forward to reverse, while applying only slight acceleration. Rocking a vehicle free in this manner may cause the ABS or traction system malfunction indicator light to come on. Turn off the engine and restart the engine to clear the malfunction indication.
STARTING AND OPERATING 223 You can shift in or out of the autostick mode at any time without taking your foot off the accelerator pedal. If you choose the Overdrive mode, the transmission will operate automatically; shifting between the five available gears. When you wish to engage autostick, simply move the shift lever to the Right or Left (D+/D-) position while in DRIVE. The transmission will remain in the current gear until an upshift or downshift is chosen.
STARTING AND OPERATING To release the parking brake, pull out on the parking brake release located on the left side of the instrument panel. The parking brake should always be applied when the driver is not in the vehicle. WARNING! Parking Brake Release When parking on a hill, it is important to set the parking brake before placing the gear selector in Park, otherwise the load on the transmission locking mechanism may make it difficult to move the selector out of park.
STARTING AND OPERATING 225 BRAKE SYSTEM In the event power assist is lost for any reason (for example, repeated brake applications with the engine off), the brakes will still function. The effort required to brake the vehicle will be much greater than that required with the power system operating. Your vehicle is equipped with dual hydraulic brake systems. If either of the two hydraulic systems lose normal capability, the remaining system will still function.
STARTING AND OPERATING WARNING! • Anti-lock system (ABS) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded. • The ABS cannot prevent accidents, including those resulting from excessive speed in turns, following another vehicle too closely, or hydroplaning. Only a safe, attentive, and skillful driver can prevent accidents.
STARTING AND OPERATING 227 ABS is activated during braking under certain road or stopping conditions. ABS-inducing conditions can include ice, snow, gravel, bumps, railroad tracks, loose debris, or panic stops.
STARTING AND OPERATING POWER STEERING The standard power steering system will give you good vehicle response and increased ease of maneuverability in tight spaces. The system will provide mechanical steering capability if power assist is lost. If for some reason, the power assist is interrupted, it will still be possible to steer your vehicle. Under these conditions you will observe a substantial increase in steering effort, especially at very low vehicle speeds and during parking maneuvers.
STARTING AND OPERATING 229 MULTI DISPLACEMENT SYSTEM (MDS) - 5.7L Engine Only This feature offers improved fuel economy by shutting off four of the engine’s eight cylinders during light load and cruise conditions. The system is automatic with no driver inputs or additional driving skills required. NOTE: The MDS system may take some time to return to full functionality after a battery disconnect.
STARTING AND OPERATING TIRE PRESSURE MONITOR SYSTEM — IF EQUIPPED The Tire Pressure Monitoring System consists of the following components: Tire Pressure Monitoring — Base System The Tire Pressure Monitor System (TPMS) uses wireless technology with wheel rim mounted electronic sensors to monitor tire pressure levels (EXCLUDING THE SPARE TIRE). Sensors, mounted to each wheel as part of the valve stem, transmit tire pressure readings to the Receiver Module.
STARTING AND OPERATING 231 CAUTION! The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equipment that is not of the same size, type, and/or style. After-market wheels can cause sensor damage. Do not use tire sealant from a can, or balance beads if your vehicle is equipped with a TPMS, as damage to the sensors may result.
STARTING AND OPERATING The Tire Pressure Monitoring Telltale Light will illuminate in the instrument cluster, and an audible chime will be activated when one or more tire pressures is low. The Tire Pressure Monitoring Telltale Light will flash on and off for 10 to 60 seconds when a system fault is detected. The flash cycle will repeat every ten minutes or until the fault condition is removed and reset.
STARTING AND OPERATING 233 LEFT FRONT, LEFT REAR, RIGHT FRONT, RIGHT REAR LOW PRESSURE One or more of these messages will be displayed in the EVIC if a low tire pressure condition exists in one or more tires. Inspect all tires for proper inflation pressure, once the proper tire pressure has been set, the TPMS warning will reset automatically when the vehicle has been driven for at least 2 minutes at or above 15 mph (24 km/h).
STARTING AND OPERATING NOTE: • The TPMS can inform the driver of a low tire pressure condition. TIRE SAFETY INFORMATION Tire Markings • The TPMS is not intended to replace normal tire care and maintenance, nor to provide warning of a tire failure or condition. • The TPMS should not be used as a tire pressure gauge while adjusting your tire pressure. General Information This device complies with part 15 of the FCC rules and RSS 210 of Industry Canada.
STARTING AND OPERATING 235 • European Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter ⬙P⬙ is absent from this tire size designation. Example: 215/65R15 96H • Temporary Spare tires are high pressure compact spares designed for temporary emergency use only. Tires designed to this standard have the letter “T” molded into the sidewall preceding the size designation.
STARTING AND OPERATING Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ⴖ....blank....ⴖ = Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary Spare tire 31 = Overall Diameter in Inches (in) 215 = Section Width in Millimeters (mm) 65 = Aspect Ratio in Percent (%) —Ratio of section height to section width of tire. 10.
STARTING AND OPERATING 237 EXAMPLE: Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry. H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions. —The maximum speed corresponding to the Speed Symbol should only be achieved under specified operating conditions. (i.e. tire pressure, vehicle loading, road conditions and posted speed limits).
STARTING AND OPERATING Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire however the date code may only be on one side. Tires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire. Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the outboard side then you will find it on the inboard side of the tire.
STARTING AND OPERATING 239 Tire Loading and Tire Pressure Tire and Loading Information Placard Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on either the face of the driver’s door or the driver’s side “B” pillar.
STARTING AND OPERATING Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the “Tire and Loading Information” placard and in the “Vehicle Loading” section of this manual.
STARTING AND OPERATING 241 5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4. 6. If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle.
STARTING AND OPERATING
STARTING AND OPERATING 243 WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES—GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle. Three primary areas are affected by improper tire pressure: 1.
STARTING AND OPERATING 2. Economy— Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Underinflation also increases tire rolling resistance and results in higher fuel consumption. 3. Ride Comfort and Vehicle Stability— Proper tire inflation contributes to a comfortable ride. Overinflation produces a jarring and uncomfortable ride.
STARTING AND OPERATING 245 CAUTION! After inspecting or adjusting the tire pressure, always reinstall the valve stem cap–if equipped. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressures specified on the placard are always “cold tire inflation pressure”. Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or driven less than 1 mile (1 km) after a 3 hour period.
STARTING AND OPERATING WARNING! High speed driving with your vehicle under maximum load is dangerous. The added strain on your tires could cause them to fail. You could have a serious accident. Don’t drive a vehicle loaded to the maximum capacity at continuous speeds above 75 mph (120 km/h). Cuts and punctures in radial tires are repairable only in the tread area because of sidewall flexing. Consult your authorized tire dealer for radial tire repairs.
STARTING AND OPERATING 247 Do not install a wheel cover or attempt to mount a conventional tire on the compact spare wheel, since the wheel is designed specifically for the compact spare. tire affects vehicle handling. Since it is not the same tire, replace (or repair) the original tire and reinstall on the vehicle at the first opportunity. Do not install more than one compact spare tire/wheel on the vehicle at any given time.
STARTING AND OPERATING WARNING! Fast spinning tires can be dangerous. Forces generated by excessive wheel speeds may cause tire damage or failure. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 35 mph (55 km/h) when you are stuck. And don’t let anyone near a spinning wheel, no matter what the speed. Tread Wear Indicators Tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced.
STARTING AND OPERATING 249 Life of Tire The service life of a tire is dependent upon varying factors including but not limited to: • Driving style • Tire pressure • Distance driven WARNING! Tires and spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure. You could lose control and have an accident resulting in serious injury or death.
STARTING AND OPERATING WARNING! CAUTION! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle. This can cause unpredictable handling and stress to steering and suspension components. You could lose control and have an accident resulting in serious injury or death.
STARTING AND OPERATING 251 TIRE CHAINS Use only compact chains, or other traction aids that meet SAE type “Class S” specifications. Chains must be the proper size for the vehicle, as recommended by the chain manufacturer. NOTE: Do not use tire chains on a compact spare tire. CAUTION! To avoid damage to your vehicle or tires, observe the following precautions: • Because of restricted chain clearance between tires and other suspension components, it is important that only chains in good condition are used.
STARTING AND OPERATING NOTE: In order to avoid damage to tires, chains, and your vehicle do not drive for a prolonged period of time on dry pavement. Observe the tire chain manufacturer’s instructions on method of installation, operating speed, and conditions for usage. Always use the lower suggested operating speed if both the chain manufacturer and vehicle manufacture suggest a maximum speed. This notice applies to all chain traction devices, including link and cable (radial) chains.
STARTING AND OPERATING 253 Follow the recommended tire rotation frequency for your type of driving found in the “Maintenance Schedules” Section of this manual. More frequent rotation is permissible if desired. The reasons for any rapid or unusual wear should be corrected prior to rotation being performed. The suggested rotation method is the “forward-cross” shown in the following diagram. FUEL REQUIREMENTS 2.
STARTING AND OPERATING Spark Knock Light spark knock at low engine speeds is not harmful to your engine. However, continued heavy spark knock at high speeds can cause damage and immediate service is required. Poor quality gasoline can cause problems such as hard starting, stalling and hesitations. If you experience these symptoms, try another brand of “regular” gasoline before considering service for the vehicle.
STARTING AND OPERATING 255 CAUTION! DO NOT use gasolines containing Methanol. Use of these blends may result in starting and driveability problems and may damage critical fuel system components. Problems that result from using methanol/gasoline blends are not the responsibility of the manufacturer. While MTBE is an oxygenate made from Methanol, it does not have the negative effects of Methanol.
STARTING AND OPERATING Fuel System Cautions CAUTION! Follow these guidelines to maintain your vehicle’s performance: • The use of leaded gas is prohibited by Federal law. Using leaded gasoline can impair engine performance, or damage the emission control system. • An out-of-tune engine, or certain fuel or ignition malfunctions, can cause the catalytic converter to overheat.
STARTING AND OPERATING 257 • Do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas which can kill. Never run the engine in a closed area, such as a garage, and never sit in a parked vehicle with the engine running for an extended period. If the vehicle is stopped in an open area with the engine running for more than a short period, adjust the ventilation system to force fresh, outside air into the vehicle.
STARTING AND OPERATING NOTE: When removing the fuel filler cap, lay the cap tether in the hook, located on the fuel filler cap door reinforcement. CAUTION! Damage to the fuel system or emission control system could result from using an improper fuel tank filler tube cap (gas cap), and may result in a malfunction indicator light on the instrument cluster. A poorly fitting cap could let impurities into the fuel system.
STARTING AND OPERATING 259 NOTE: • Tighten the gas cap until you hear a “clicking” sound. This is an indication that the gas cap is properly tightened. If the gas cap is not secured properly the Malfunction Indicator Light in the instrument cluster will turn on. Make sure that the gas cap is tightened each time the vehicle is refueled. • When the fuel nozzle “clicks” or shuts off, the fuel tank is full.
STARTING AND OPERATING VEHICLE LOADING The load carrying capacity of your vehicle is shown in the charts that follow. This information should be used for passenger and luggage loading as indicated. If the seatbacks are folded for carrying cargo, do not exceed the specified GVWR and GAWR. Vehicle Certification Label Your vehicle has a certification label attached to the rear of the driver’s door.
STARTING AND OPERATING 261 Overloading The load carrying components (axle, springs, tires, wheels, etc.) of your vehicle will provide satisfactory service as long as you do not exceed the GVWR and front and rear GAWR. The best way to figure out the total weight of your vehicle is to weigh it when it is fully loaded and ready for operation. Weigh it on a commercial scale to insure that it is not over the GVWR. Figure out the weight on the front and rear of the vehicle separately.
STARTING AND OPERATING Empty Weight Load (Including driver, passsengers and cargo) Total GAWR Front Rear Axle Axle 2054 lbs 1805 lbs (932 kg) (819 kg ) 271 lbs 579 lbs (123 kg) (263 kg) 2325 lbs 2384 lbs (1055 kg) (1081 kg) 2546 lbs 2708 lbs (1155 kg) (1228 kg) NOTE: Refer to the Vehicle Certification Label attached to the rear of the driver’s door for your vehicle’s GVWR and GAWRs. This table is only an example.
STARTING AND OPERATING 263 Gross Trailer Weight (GTW) The gross trailer weight (GTW) is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or temporary) loaded in or on the trailer in its ⬙loaded and ready for operation⬙ condition. The recommended way to measure GTW is to put your fully loaded trailer on a vehicle scale. The entire weight of the trailer must be supported by the scale.
STARTING AND OPERATING Weight-Distributing Hitch A weight-distributing hitch includes a receiver attached to the tow vehicle, plus a removable hitch head and spring bar assembly that fits into the receiver opening and hook up brackets that connect the spring bars to the trailer frame. See your authorized dealer for a trailer hitch engineered specifically for your vehicle.
STARTING AND OPERATING 265 Engine/Transmission Frontal Area 22 SQ. FT. (2.04 square meters) 22 SQ. FT. (2.04 square meters) 22 SQ. FT. (2.04 square meters) 22 SQ. FT. (2.04 square meters) 3.5L & 5.7L Automatic 32 SQ. FT. (2.97 square meters) 32 SQ. FT. (2.97 square meters) 32 SQ. FT. (2.97 square meters) 32 SQ. FT. (2.97 square meters) Refer to local laws for maximum trailer towing speeds. 2.
STARTING AND OPERATING Trailer and Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% to 15% of the Gross Trailer Weight (GTW) on the tow hitch of your vehicle. Loads balanced over the wheels or heavier in the rear can cause the trailer to sway severely side to side which will cause loss of control of the vehicle and trailer. Failure to load trailers heavier in front is the cause of many trailer accidents.
STARTING AND OPERATING 267 Towing Requirements To promote proper break-in of your new vehicle drivetrain components the following guidelines are recommended: CAUTION! • Avoid towing a trailer for the first 500 miles (805 km) of vehicle operation. Doing so may damage your vehicle. • During the first 500 miles (805 km) of trailer towing, limit your speed to 50 mph (80 km/h). Perform the maintenance listed in Section 8 of this manual. When towing a trailer, never exceed the GAWR, or GCWR, ratings.
STARTING AND OPERATING • Vehicles with trailers should not be parked on a grade. When parking, apply the parking brake on the tow vehicle. Put the tow vehicle automatic transmission in P for Park. Always, block or ⬙chock⬙ the trailer wheels. − Proper tire inflation pressures are essential to the safe and satisfactory operation of your vehicle. Refer to the Tires–General Information section of this manual on Tire Pressures for proper tire inflation procedures. • GCWR must not be exceeded.
STARTING AND OPERATING 269 − An electronically actuated trailer brake controller is required when towing a trailer with electronically actuated brakes. When towing a trailer equipped with a hydraulic surge actuated brake system, an electronic brake controller is not required. − Trailer brakes are recommended for trailers over 1,000 lbs (454 kg) and required for trailers in excess of 2,000 lbs (907 kg).
STARTING AND OPERATING The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. Refer to the following illustrations.
STARTING AND OPERATING 271 Towing Tips Before setting out on a trip, practice turning, stopping and backing the trailer in an area away from heavy traffic. Towing Tips — Automatic Transmission The “D” range can be selected when towing. However, if frequent shifting occurs while in this range, the “3” range should be selected.
STARTING AND OPERATING − Extended driving at high RPM should be avoided to prevent excess heat generation. A reduction in vehicle speed may be required to avoid extended driving at high RPM. Return to a higher gear range or vehicle speed when road conditions and RPM level allows.
WHAT TO DO IN EMERGENCIES CONTENTS 䡵 Hazard Warning Flasher . . . . . . . . . . . . . . . . . 274 ▫ Acceleration . . . . . . . . . . . . . . . . . . . . . . . . . 284 䡵 If Your Engine Overheats . . . . . . . . . . . . . . . . 274 ▫ Traction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 285 䡵 Jacking And Tire Changing . . . . . . . . . . . . . . . 275 䡵 Freeing A Stuck Vehicle . . . . . . . . . . . . . . . . . 285 ▫ Preparations For Jacking . . . . . . . . . . . . . . . .
WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER The hazard flasher switch is located in the center of the instrument panel between the center air outlets. This is an emergency warning system and should not be used when the vehicle is in motion. Use it when your vehicle is disabled and is creating a safety hazard for other motorists. When you must leave the vehicle to seek assistance, the Hazard Warning Flashers will continue to operate even though the ignition switch is OFF.
WHAT TO DO IN EMERGENCIES 275 NOTE: There are steps that you can take to slow down an impending overheat condition. If your air conditioner is on, turn it off. The air conditioning system adds heat to the engine cooling system and turning off the A/C removes this heat. You can also turn the Temperature control to maximum heat, the Mode control to floor, and the fan control to HI. This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.
WHAT TO DO IN EMERGENCIES WARNING! Getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never get any part of your body under a vehicle that is on a jack. Never start or run the engine while the vehicle is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift.
WHAT TO DO IN EMERGENCIES 277 Jack Location/Spare Tire Stowage • Remove the fastener securing the spare tire. The jack and spare tire are both stowed under an access cover in the trunk. Follow these steps to access the jack and spare tire. NOTE: The spare tire must be removed in order to access the jack. • Open the trunk. • Lift the access cover using the pull strap.
WHAT TO DO IN EMERGENCIES • Remove the spare tire. 2. Remove the spare tire, jack and lug wrench. • Remove the fastener securing the jack. 3. Before raising the vehicle, use lug wrench to carefully pry off wheel cover (if equipped with steel wheels) or center cap (if equipped with aluminum wheels). Jack Fastener Jacking and Changing a Tire 1. Block the wheel diagonally opposite the flat tire. Passengers should not remain in the vehicle when the vehicle is being jacked.
WHAT TO DO IN EMERGENCIES 279 WARNING! To avoid possible personal injury, handle the wheel covers with care to avoid contact with the metal edges and retention teeth. 5. Turn the jack screw clockwise to firmly engage the jack saddle with the lift area of the sill flange, use the lift area closest to the flat tire. 6. Raise the vehicle just enough to remove the flat tire and install the spare tire. 4. Before raising the vehicle loosen, but do not remove, the lug nuts of the flat tire using the lug wrench.
WHAT TO DO IN EMERGENCIES Jack Engagement Locations
WHAT TO DO IN EMERGENCIES 281 7. Remove the lug nuts, wheel cover (if equipped) and tire. Remove the cover by hand, do not pry off. WARNING! 8. Mount the spare tire. For vehicles equipped with wheel covers, see the wheel cover installation instructions. Do not attempt to install a wheel cover on a compact spare. A loose tire or jack thrown forward in a collision or hard stop could endanger the occupants of the vehicle. Always stow the jack parts and the spare tire in the places provided. 9.
WHAT TO DO IN EMERGENCIES Wheel Cover Installation (If Required) 2. Align the valve notch in the wheel cover with the valve stem on the wheel. 3. Install the cover by hand, snapping the cover over the two lug nuts. Do not use a hammer or excessive force to install the cover. 4. Return to Changing a Tire Section, Item #9 above. JUMP-STARTING PROCEDURES IF BATTERY IS LOW WARNING! 1. Tighten the two lug nuts on the mounting studs on each side of the stud which is in alignment with the valve stem.
WHAT TO DO IN EMERGENCIES 283 WARNING! • Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transmission cannot be started this way. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle. If the vehicle has a discharged battery, booster cables may be used to obtain a start from another vehicle. This type of start can be dangerous if done improperly, so follow this procedure carefully.
WHAT TO DO IN EMERGENCIES 4. Connect one end of the jumper cable to the remote jump start positive battery post (A) in the engine compartment. Connect the other end of the same cable to the positive terminal of the booster battery. Refer to the following illustration for jump starting connections. 5. Connect the other cable, first to the negative terminal of the booster battery and then to the engine ground (B) of the vehicle with the discharged battery.
WHAT TO DO IN EMERGENCIES 285 WARNING! Rapid acceleration on slippery surfaces is dangerous. Unequal traction can cause sudden pulling of the rear wheels. You could lose control of the vehicle and possibly have an accident. Accelerate slowly and carefully whenever there is likely to be poor traction (ice, snow, wet mud, loose sand, etc.). Traction When driving on wet or slushy roads, it is possible for a wedge of water to build up between the tire and road surface.
WHAT TO DO IN EMERGENCIES WARNING! Fast spinning tires can be dangerous. Forces generated by excessive wheel speeds may cause tire damage or failure. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 35 mph (55 km/h) when you are stuck. And don’t let anyone near a spinning wheel, no matter what the speed. CAUTION! Racing the engine or spinning the wheels too fast may lead to transmission overheating and failure. It can also damage the tires.
WHAT TO DO IN EMERGENCIES 287 CAUTION! • Do not attempt to tow this vehicle from the front with sling type towing equipment. Damage to the front fascia will result. • The only approved method of towing is with a flat bed truck. • Do not tow the vehicle from the rear. Damage to the rear sheet metal, and fascia will occur. • Do not push or tow this vehicle with another vehicle as damage to the bumper fascia and transmission may result.
MAINTAINING YOUR VEHICLE CONTENTS 䡵 2.7L Engine . . . . . . . . . . . . . . . . . . . . . . . . . . 292 䡵 3.5L Engine . . . . . . . . . . . . . . . . . . . . . . . . . . 293 䡵 5.7L Engine . . . . . . . . . . . . . . . . . . . . . . . . . . 294 䡵 Onboard Diagnostic System — OBD II . . . . . . 295 䡵 Emissions Inspection And Maintenance Programs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 296 ▫ Drive Belts — Check Condition And Tensioner . . . . . . . . . . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE ▫ Body Lubrication . . . . . . . . . . . . . . . . . . . . . 309 ▫ Windshield Wiper Blades . . . . . . . . . . . . . . . . 310 ▫ Windshield Washers/Headlight Washers — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 310 ▫ Cleaning The Center Console Cup Holders — 300C And 300 Touring Models . . . . . . . . . . . . 325 䡵 Power Distribution Centers . . . . . . . . . . . . . . . 325 ▫ Front Power Distribution Center . . . . . . . . . . . 325 ▫ Exhaust System . . .
MAINTAINING YOUR VEHICLE 291 䡵 Fluids And Capacities . . . . . . . . . . . . . . . . . . . 344 ▫ Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 345 䡵 Fluids, Lubricants And Genuine Parts . . . . . . . 345 ▫ Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 2.7L ENGINE 2.
MAINTAINING YOUR VEHICLE 293 3.5L ENGINE 7 3.
MAINTAINING YOUR VEHICLE 5.7L ENGINE 5.
MAINTAINING YOUR VEHICLE 295 ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
MAINTAINING YOUR VEHICLE EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle’s emissions control system. Failure to pass could prevent vehicle registration. For states which have an I/M (Inspection and Maintenance) requirement, this check verifies the following: the MIL (Malfunction Indicator Light) is functioning and is not on when the engine is running, and that the OBD (On Board Diagnostic) system is ready for testing.
MAINTAINING YOUR VEHICLE 297 If your OBD system is not ready, you should see your authorized dealer or repair facility. If your vehicle was recently serviced or had a battery failure or replacement, you may need to do nothing more than drive your vehicle as you normally would in order for your OBD system to update. A recheck with the above test routine may then indicate that the system is now ready.
MAINTAINING YOUR VEHICLE WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the proper equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic. MAINTENANCE PROCEDURES The pages that follow contain the required maintenance services determined by the engineers who designed your vehicle.
MAINTAINING YOUR VEHICLE 299 The best time to check the engine oil level is about 5 minutes after a fully warmed engine is shut off or before starting the engine after it has sat overnight. Checking the oil while the vehicle is on level ground will improve the accuracy of the oil level readings. Maintain the oil level in the “SAFE” range. Adding one quart (.9L) of oil when the reading is at the bottom of the “SAFE” range will result in an oil level at the top of the “SAFE” range on these engines.
MAINTAINING YOUR VEHICLE CAUTION! Overfilling or underfilling will cause oil aeration or loss of oil pressure. This could damage your engine. • Short trips of less than 10 miles (16 km). • More than 50% of your driving is at sustained high speeds during hot weather, above 90°F (32°C). • Trailer towing. • Taxi, Police or delivery service (commercial service). CAUTION! • Off-Road or desert operation.
MAINTAINING YOUR VEHICLE 301 recommends engine oils that are API certified and meet the requirements of DaimlerChrysler Material Standard MS-6395. Use Mopar威 or an equivalent oil meeting the specification MS-6395. The engine oil filler cap also shows the recommended engine oil viscosity for your engine. For information on engine oil filler cap location, refer to the Engine Compartment illustration in this section.
MAINTAINING YOUR VEHICLE engine oil viscosity chart. SAE 5W-30 Engine Oil is allowed for use in the 3.5L Engine during cold weather only to improve cold weather starting. both an SAE grade number and the API Certification Symbol or ACEA category shown on the container should be used. Lubricants which do not have both, the engine oil certification mark and the correct SAE viscosity grade number should not be used.
MAINTAINING YOUR VEHICLE 303 environment. Contact your dealer, service station, or governmental agency for advice on how and where used oil and oil filters can be safely discarded in your area. At the mileage indicated in the maintenance schedule, all belts and tensioner should be checked for condition. Improper belt tension can cause belt slippage and failure. Engine Oil Filter The engine oil filter should be replaced at every engine oil change.
MAINTAINING YOUR VEHICLE Engine Air Cleaner Filter Under normal driving conditions, replace the air filter at the intervals shown on Schedule “A.” If, however, you drive the vehicle frequently under dusty or severe conditions, the filter element should be inspected periodically and replaced if necessary at the intervals shown on Schedule “B.” WARNING! The air cleaner can provide a measure of protection in the case of engine backfire.
MAINTAINING YOUR VEHICLE 305 CAUTION! WARNING! Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition. In the event of engine malfunction, particularly involving engine misfire or other apparent loss of performance, have your vehicle serviced promptly. Continued operation of your vehicle with a severe malfunction could cause the converter to overheat, resulting in possible damage to the converter and the vehicle.
MAINTAINING YOUR VEHICLE To minimize the possibility of catalyst damage: • Do not shut off the engine or interrupt the ignition when the transmission is in gear and the vehicle is in motion. • Do not try to start engine by pushing or towing the vehicle. NOTE: The battery is stored under an access cover in the trunk. Remote battery terminals are located in the engine compartment for jump starting.
MAINTAINING YOUR VEHICLE 307 WARNING! CAUTION! • Battery fluid is a corrosive acid solution and can burn or even blind you. Don’t allow battery fluid to contact your eyes, skin or clothing. Don’t lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area immediately with large amounts of water. • Battery gas is flammable and explosive. Keep flame or sparks away from the battery.
MAINTAINING YOUR VEHICLE WARNING! • Use only refrigerants and compressor lubricants approved by the manufacturer for your air conditioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs. Refer to Section 3 of the Warranty Information book for further warranty information. • The air conditioning system contains refrigerant under high pressure.
MAINTAINING YOUR VEHICLE 309 Refer to the “Maintenance Schedules” section of this manual for the recommended air conditioning filter replacement intervals. Power Steering — Fluid Check Checking the power steering fluid level at a defined service interval is not required. The fluid should only be checked if a leak is suspected, abnormal noises are apparent, and/or the system is not functioning as anticipated. Coordinate inspection efforts through a certified DaimlerChrysler Dealership.
MAINTAINING YOUR VEHICLE underhood services, the hood latch, release mechanism and safety catch should be cleaned and lubricated. The external lock cylinders should be lubricated twice a year, preferably in the fall and spring. Apply a small amount of a high quality lubricant such as Mopar威 Lock Cylinder Lubricant or equivalent directly into the lock cylinder.
MAINTAINING YOUR VEHICLE 311 The fluid reservoir will hold 1 gallon (3.8L) of washer fluid when the message “Low Washer Fluid” appears in the Electronic Vehicle Information Center (EVIC) — if equipped. Exhaust System The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system.
MAINTAINING YOUR VEHICLE Cooling System WARNING! • When working near the radiator cooling fan, disconnect the fan motor lead or turn the ignition switch to the OFF position. The fan is temperature controlled and can start at any time the ignition switch is in the ON position. • You or others can be badly burned by hot coolant or steam from your radiator. If you see or hear steam coming from under the hood, don’t open the hood until the radiator has had time to cool.
MAINTAINING YOUR VEHICLE 313 Cooling System — Drain, Flush and Refill At the intervals shown on the Maintenance Schedules, the system should be drained, flushed and refilled. If the solution is dirty or contains a considerable amount of sediment, clean and flush with a reliable cooling system cleaner. Follow with a thorough rinsing to remove all deposits and chemicals. Properly dispose of old antifreeze solution.
MAINTAINING YOUR VEHICLE Adding Coolant Your vehicle has been built with an improved engine coolant that allows extended maintenance intervals. This coolant can be used up to 5 Years or 100,000 miles (160 000 km) before replacement. To prevent reducing this extended maintenance period, it is important that you use the same coolant throughout the life of your vehicle. Please review these recommendations for using Hybrid Organic Additive Technology (HOAT) coolant.
MAINTAINING YOUR VEHICLE 315 WARNING! • The warning words “DO NOT OPEN HOT” on the cooling system pressure cap are a safety precaution. Never add coolant when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system. To prevent scalding or injury, do not remove the pressure cap while the system is hot or under pressure. • Do not use a pressure cap other than the one specified for your vehicle.
MAINTAINING YOUR VEHICLE Points To Remember NOTE: When the vehicle is stopped after a few miles (kilometers) of operation, you may observe vapor coming from the front of the engine compartment. This is normally a result of moisture from rain, snow, or high humidity accumulating on the radiator and being vaporized when the thermostat opens, allowing hot coolant to enter the radiator.
MAINTAINING YOUR VEHICLE 317 Pay particular attention to those hoses nearest to high heat sources such as the exhaust manifold. Inspect hose routing to be sure hoses do not come in contact with any heat source or moving component which may cause heat damage or mechanical wear. Insure nylon tubing in these areas has not melted or collapsed. Inspect all hose connections such as clamps and couplings to make sure they are secure and no leaks are present.
MAINTAINING YOUR VEHICLE NOTE: Often, fluid such as oil, power steering fluid, and brake fluid are used during assembly plant operations to facilitate the assembly of hoses to couplings. Therefore, oil wetness at the hose-coupling area is not necessarily an indication of leakage. Actual dripping of hot fluid when systems are under pressure (during vehicle operation), should be noted before a hose is replaced based on leakage.
MAINTAINING YOUR VEHICLE 319 Use only manufacturers recommended brake fluid, refer to Fluids, Lubricants and Genuine Parts for correct fluid type. WARNING! • Overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts and the brake fluid catching fire.
MAINTAINING YOUR VEHICLE Automatic Transmission Fluid Level Check Regular automatic transmission fluid level checks are not required. For this reason the dipstick is omitted. If you notice fluid loss or gear shift malfunction, have your authorized dealer check the transmission fluid level. CAUTION! Using a transmission fluid other than the manufacturer’s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder.
MAINTAINING YOUR VEHICLE 321 All Wheel Drive (AWD) — If Equipped The all wheel drive system consists of a Transfer Case, and Front Differential. The exterior surface of these components should be inspected for evidence of fluid leaks. Confirmed leaks should be repaired as soon as possible. The transfer case fill plug is located on the rear housing near the output shaft. The level can be verified by the service plug in the middle of the rear housing, even with the bottom of the hole.
MAINTAINING YOUR VEHICLE hot or cold weather and other extreme conditions will have an adverse effect on paint, metal trim, and underbody protection. The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle. What Causes Corrosion? Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle. The most common causes are: • Road salt, dirt and moisture accumulation.
MAINTAINING YOUR VEHICLE 323 Special Care • If you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month. • It is important that the drain holes in the lower edges of the doors, rocker panels and trunk be kept clear and open. • If you detect any stone chips or scratches in the paint, touch them up immediately. The cost of such repairs is considered the responsibility of the owner.
MAINTAINING YOUR VEHICLE Mopar威 Total Clean is specifically recommended for leather upholstery. Your leather upholstery can be best preserved by regular cleaning with a damp soft cloth. Small particles of dirt can act as an abrasive and damage the leather upholstery and should be removed promptly with a damp cloth. Stubborn soils can be removed easily with a soft cloth and Mopar威 Total Clean or equivalent. Care should be taken to avoid soaking your leather upholstery with any liquid.
MAINTAINING YOUR VEHICLE 325 Seat Belt Maintenance Do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage can also weaken the fabric. If the belts need cleaning use Mopar威 Total Clean, a mild soap solution, or lukewarm water. Do not remove the belts from the vehicle to wash them. Replace the belts if they appear frayed or worn or if the buckles do not work properly.
MAINTAINING YOUR VEHICLE Power Distribution Centers Front Power Distribution Center A power distribution center is located in the engine compartment. This center contains fuses and relays. Front Power Distribution Center CAUTION! • When installing the Power Distribution Center cover, it is important to ensure the cover is properly positioned and fully latched. Failure to do so may allow water to get into the Power Distribution Center, and possibly result in a electrical system failure.
MAINTAINING YOUR VEHICLE 327 Front Power Distribution Center Fuses Cavity 1 2 3 4 5 6 7 8 9 10 Fuse 20 Amp Yellow 20 Amp Yellow 15 Amp Blue 20 Amp Yellow 20 Amp Yellow 15 Amp Blue 20 Amp Yellow 15 Amp Blue 15 Amp Blue 5 Amp Orange Circuits Left High Intensity Discharge Headlight - if equipped Right High Intensity Discharge Headlight - if equipped Adjustable Pedals - if equipped AC Clutch/Horn Headlight Washer - If Equipped Front Control Module (FCM) Fog Lights Lights – License, Park, Side Marker, Stop, T
MAINTAINING YOUR VEHICLE Cavity 22 23 24 25 26 27 Fuse 40 Amp Green 50 Amp Red 60 Amp Yellow 30 Amp Pink 20 Amp Blue 30 Amp Pink Circuits AC Clutch/Radiator Fan High — Low High Intensity Lighting - if equipped Radiator Fan - AWD Rear Power Distribution Center There is also a power distribution center located in the trunk under the spare tire access panel. This center contains fuses and relays.
MAINTAINING YOUR VEHICLE 329 CAUTION! Rear Power Distribution Center • When installing the Power Distribution Center cover, it is important to ensure the cover is properly positioned and fully latched. Failure to do so may allow water to get into the Power Distribution Center, and possibly result in a electrical system failure. • When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating.
MAINTAINING YOUR VEHICLE Rear Power Distribution Center Fuses Cavity 1 2 3 4 5 6 7 8 9 10 Fuse 60 Amp Yellow 40 Amp Green — 40 Amp Green 30 Amp Pink 20 Amp Yellow — 15 Amp Blue 20 Amp Yellow — Circuits Ignition Off Draw (IOD) Cavity 11 Fuse 25 Amp C/BRKR 12 25 Amp C/BRKR 25 Amp C/BRKR Battery — Battery 13 Heated Seats - if equipped Fuel Pump — Ignition Switch/Occupant Classification Module (OCM) Console Power Outlet 14 10 Amp Red 15 — 16 17 20 Amp Yellow — 20 Amp Yellow Circuits Cluster
MAINTAINING YOUR VEHICLE 331 Cavity 18 19 20 21 22 23 24 25 26 27 28 29 Fuse 20 Amp Yellow 10 Amp Red — — — — — — — 10 Amp Red 10 Amp Red 5 Amp Orange Circuits Selectable Power Outlet Cavity 30 Fuse 10 Amp Red 31 32 33 34 35 — — — — 5 Amp Orange Stop Lights — — — — — — — Airbag/Occupant Classification Module Curtain Airbag - if equipped Antilock Brakes Module/ Cluster/Front Control Module (FCM)/Powertrain Control Module (PCM)/Sentry Key Remote Keyless Entry/Stop Lights 36 20 Amp Yellow Circuits D
MAINTAINING YOUR VEHICLE Cavity 37 38 39 40 Fuse 15 Amp Blue 5 Amp Orange 10 Amp Red 5 Amp Orange 41 10 Amp Red 42 30 Amp Pink 30 Amp Pink 20 Amp Blue 43 44 Circuits Transmission - NAG1 Analog Clock/Cargo Light/ Overhead Console - if equipped Heated Mirrors - if equipped Heated Seats - if equipped/ Inside Rearview Mirror/ Manual Temperature Control (early build) - if equipped AC Heater Control (except early build MTC)/Park Assist - if equipped/Tire Pressure Monitoring - if equipped Front Blower
MAINTAINING YOUR VEHICLE 333 REPLACEMENT LIGHT BULBS LIGHT BULBS — Interior Bulb Number Rear Courtesy/Reading Lights. . . . . . . . . . . . . . W5W Rear Compartment (Trunk) Light . . . . . . . . . . . . . 579 Overhead Console Reading Lights. . . . . . . . . . . . . 578 Visor Vanity Lights . . . . . . . . . . . . . . . . . . . . . A6220 Glove Box Light . . . . . . . . . . . . . . . . . . . . . . . . . 194 Door Courtesy . . . . . . . . . . . . . . . . . . . . . . . . . . 562 Shift Indicator Light . . . . . .
MAINTAINING YOUR VEHICLE LIGHT BULBS — Exterior (300C Models) Bulb Number Low Beam Headlight (Standard Halogen). . . . . 9006XS Low Beam Headlight – High Intensity Discharge (HID) . . . . . . . . . . . . . . . . . . D1S (Serviced at Dealer) High Beam Headlight. . . . . . . . . . . . . . . . . . . . . 9005 Front Park/Turn Light . . . . . . . . . . . . . . . . . . 3157AK Front Fog Light. . . . . . . . 9145/H10 (Serviced at Dealer) Front Sidemarker . . . . . . . . .
MAINTAINING YOUR VEHICLE 335 7
MAINTAINING YOUR VEHICLE Low Beam Headlight, High Beam Headlight, and Park/Turn Light – 300C High Intensity Discharge Headlights (HID) — If Equipped The headlights are a type of high voltage discharge tube. High voltage can remain in the circuit even with the headlight switch off and the key removed. Because of this, you should not attempt to service a headlight bulb yourself. If a headlight bulb fails, take your vehicle to an authorized dealer for service.
MAINTAINING YOUR VEHICLE 337 NOTE: On vehicles equipped with High Intensity Discharge Headlights (HID), when the headlights are turned on there is a blue hue to the lights. This diminishes and becomes more white after approximately 10 seconds, as the system charges. • Open the hood. • Twist the appropriate bulb socket assembly counterclockwise and pull out. Pull the bulb out of the socket assembly.
MAINTAINING YOUR VEHICLE Backup Light, Side Marker Light, and Tail/Stop Turn Light — 300 Models 1. Open the Trunk. 2. Remove two fasteners from the back of the tail light assembly. CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with an oily surface, clean the bulb with rubbing alcohol.
MAINTAINING YOUR VEHICLE 339 3. Pull back the trunk liner. 4. Remove the remaining fastener from the back of the tail light assembly. 7. Pull tail light assembly clear from vehicle to access bulbs. Turn bulb sockets counter-clockwise to remove. 5. Push the electrical connector locking tab to the side. 6. Disconnect the electrical connector.
MAINTAINING YOUR VEHICLE 8. Pull the appropriate bulb to remove it from the socket. 9. Replace the bulb, reinstall the socket, and reattach the tail light assembly. 10. Close the trunk.
MAINTAINING YOUR VEHICLE 341 Tail/Stop, Tail, Turn Signal Light, and Backup Light — 300C Models 1. Open the Trunk. 2. Remove two fasteners from the back of the tail light assembly. 3. Pull back the trunk liner. 4. Remove the remaining fastener from the back of the tail light assembly. 5. Push the electrical connector locking tab to the side. 6. Disconnect the electrical connector.
MAINTAINING YOUR VEHICLE 7. Pull tail light assembly clear from vehicle to access bulbs. Turn bulb sockets counter-clockwise to remove.
MAINTAINING YOUR VEHICLE 343 8. Pull the appropriate bulb to remove it from the socket. 9. Replace the bulb, reinstall the socket, and reattach the tail light assembly. 10. Close the trunk.
MAINTAINING YOUR VEHICLE License Light FLUIDS AND CAPACITIES 1. Remove the screws securing the light to the rear fascia. 2. Remove the bulb and socket assembly and pull the bulb from the socket. Fuel (approximate) 2.7 Liter Engines (87 Octane) 3.5 Liter Engines (87 to 89 Octane) 5.7 Liter Engines (87 to 89 Octane) Engine Oil-With Filter 2.7 Liter Engines (SAE 5W-20, API Certified) 3.5 Liter Engines (SAE 10W-30, API Certified) 5.7 Liter Engines (SAE 5W-20, API Certified) 3.
MAINTAINING YOUR VEHICLE 345 Cooling System * 2.7 Liter Engines (Mopar威 9.7 qts Antifreeze/Coolant 5 Year/ 100,000 Mile Formula) or equivalent. 3.5 Liter Engines (Mopar威 10.6 qts Antifreeze/Coolant 5 Year/ 100,000 Mile Formula) or equivalent. 5.7 Liter Engines (Mopar威 14.6 qts Antifreeze/Coolant 5 Year/ 100,000 Mile Formula) or equivalent. * Includes heater and coolant recovery bottle MAX level. 9.2 liters 10.0 liters 13.
MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant Engine Oil (2.7 Liter) Engine Oil (3.5 Liter) Engine Oil (5.7 Liter) Spark Plugs Oil Filter (2.7 Liter) Oil Filter (3.5 Liter) Oil Filter (5.7 Liter) Fuel Selection (2.7 Liter) Fuel Selection (3.5 Liter) Fuel Selection (5.7 Liter) Fluids, Lubricants and Genuine Parts Mopar威 Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) Use API Certified engine oil.
MAINTAINING YOUR VEHICLE 347 Chassis Component Automatic Transmission Brake Master Cylinder Front Axle Power Steering Reservoir Rear Axle Transfer Case Fluids, Lubricants and Genuine Parts Mopar威 ATF+4 Automatic Transmission Fluid or equivalent. Mopar威 DOT 3, SAE J1703 should be used. If DOT 3, SAE J1703 brake fluid is not available, then DOT 4 is acceptable. Use only recommended brake fluids. API Certified GL-5 SAE 75W90 Gear Lubricant or equivalent.
MAINTENANCE SCHEDULES CONTENTS M A I N T E N A N C E 䡵 Emission Control System Maintenance . . . . . . 350 ▫ Schedule “B” . . . . . . . . . . . . . . . . . . . . . . . . 353 䡵 Maintenance Schedules . . . . . . . . . . . . . . . . . . 350 ▫ Schedule “A” . . . . . . . . . . . . . . . . . . . . . . . .
M A I N T E N A N C E 350 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
MAINTENANCE SCHEDULES 351 M A • Extensive engine idling. • Driving in dusty conditions. • Short trips of less than 10 miles (16.2 km). • More than 50% of your driving is at sustained high speeds during hot weather, above 90°F (32°C). • Trailer towing.〫 • Taxi, police, or delivery service (commercial service).〫 • Off-road or desert operation.
M 352 MAINTENANCE SCHEDULES A I At Each Stop for Fuel N T • Check the engine oil level about 5 minutes after a fully E warmed engine is shut off. Checking the oil level while N A the vehicle is on level ground will improve the accuN racy of the oil level reading. Add oil only when the C level is at or below the ADD or MIN mark. E S C H E D U L E S 8 • Check the windshield washer solvent and add if required. • Check all lights and all other electrical items for correct operation.
SCHEDULE “B” 353 M A SCHEDULE “B” Follow Schedule “B” if you usually operate your vehicle under one or more of the following conditions. Change the automatic transmission fluid and filter every 60,000 miles (100 000 km) if the vehicle is usually operated under one or more of the conditions marked with an 〫. • Taxi, police or delivery service (commercial ser- I N vices).〫 T • Day or night temperatures are below 32°F (0°C).
M 354 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter, if not A replaced at 3 months. N C Inspect the air cleaner filter and replace if reE quired.* S C H E D U L E S 8 Replace the air cleaner filter. Inspect the front and rear brake linings and rotors. Replace the air conditioning filter. Rotate the tires.
SCHEDULE “B” 355 M Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Inspect the air cleaner filter and replace if required.* Replace the air cleaner filter. Replace the spark plugs. 5.7L Engine. Inspect the front and rear brake linings and rotors. Check and replace, if necessary, the PCV valve. * Replace the air conditioning filter. Rotate the tires.
M 356 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter, if not A replaced at 3 months. N C Inspect the air cleaner filter and replace if reE quired.* S C H E D U L E S 8 Replace the air cleaner filter. Inspect the front and rear brake linings and rotors. Change the rear axle fluid. Replace the air conditioning filter. Rotate the tires. Change the Transfer Case Fluid - All Wheel Drive (AWD) only.
SCHEDULE “B” 357 M Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Inspect the air cleaner filter and replace if required.* Replace the air cleaner filter. Replace the spark plugs. 5.7L Engine. Inspect the front and rear brake linings and rotors. Check and Inspect the accessory drive belt and tensioner. Replace if required. Check and replace, if necessary, the PCV valve. * ‡ Change the automatic transmission fluid and filter. Replace the air conditioning filter.
M 358 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter, if not A replaced at 3 months. N C Inspect the air cleaner filter and replace if reE quired.* S C H E D U L E S 8 Replace the air cleaner filter. Replace the spark plugs. 5.7L Engine. Inspect the front and rear brake linings and rotors. Check and replace, if necessary, the PCV valve. * ‡ Replace the air conditioning filter. Rotate the tires.
SCHEDULE “B” 359 M Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Inspect the air cleaner filter and replace if required.* Replace the air cleaner filter. Inspect the front and rear brake linings and rotors. Replace the engine timing belt. 3.5L Engine. Replace the spark plugs. 2.7L, 3.5L Engines. Check and Inspect the accessory drive belt and tensioner. Replace if required. Change the rear axle fluid. Replace the air conditioning filter.
M 360 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter, if not reA placed at 3 months. N C Inspect the air cleaner filter and replace if reE quired.* S C H E D U L E S 8 108,000 (180 000) X 111,000 (185 000) X 114,000 (190 000) X 117,000 (195 000) X X X X X Replace the air cleaner filter. Inspect the front and rear brake linings and rotors. Replace the spark plugs. 5.7L Engine. Check and replace, if necessary, the PCV valve.
SCHEDULE “A” 361 M SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Inspect the air cleaner filter and replace if required.* Replace the air cleaner filter. Replace the spark plugs. 5.7L Engine. Inspect the front and rear brake linings and rotors. Replace the air conditioning filter. Rotate the tires.
M 362 SCHEDULE “A” A I N Miles T (Kilometers) E N [Months] A Change engine oil and engine oil filter. N C Inspect the air cleaner filter and replace if E required.* S C H E D U L E S 8 Replace the air cleaner filter. Inspect the front and rear brake linings and rotors. Replace the spark plugs. 5.7L Engine. Check and Inspect the accessory drive belt and tensioner. Replace if required. Flush and replace engine coolant at 60 months if not done at 102,000 miles. Check and replace, if necessary, the PCV valve.
SCHEDULE “A” 363 M Miles (Kilometers) [Months] Change engine oil and engine oil filter. Inspect the air cleaner filter and replace if required.* Replace the air cleaner filter. Inspect the front and rear brake linings and rotors. Check and Inspect the accessory drive belt and tensioner. Replace if required. Replace the spark plugs. 2.7L, 3.5L Engines. Replace the spark plugs. 5.7L Engine. Check and replace, if necessary, the PCV valve. *‡ Replace the engine timing belt. 3.5L Engine.
M 364 SCHEDULE “A” A I N Miles T (Kilometers) E N [Months] A Change engine oil and engine oil filter. N C Inspect the air cleaner filter and replace if required.* E Replace the air cleaner filter. S C H E D U L E S 8 108,000 (180 000) [108] X X ‡ This maintenance is not required if previously replaced. Inspection and service should also be performed anytime a malfunction is observed or suspected. Retain all receipts. 120,000 (200 000) [120] X X Inspect the front and rear brake linings and rotors.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS 䡵 Suggestions For Obtaining Service For Your Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 366 ▫ Prepare For The Appointment . . . . . . . . . . . . 366 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . . . 366 䡵 Reporting Safety Defects . . . . . . . . . . . . . . . . . 369 ▫ In Canada . . . . . . . . . . . . . . . . . . . . . . . . . . 369 䡵 Publication Order Forms . . . . . . . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty, discuss additional charges with the service manager. Keep a maintenance log of your vehicle’s service history. This can often provide a clue to the current problem.
IF YOU NEED CONSUMER ASSISTANCE 367 • If for some reason you are still not satisfied, talk to the general manager or owner of the dealership. They want to know if you need assistance. • If your dealership is unable to resolve the concern, you may contact the Manufacturer’s Customer Center.
IF YOU NEED CONSUMER ASSISTANCE Service Contract You may have purchased a service contract for your vehicle to help protect you from the high cost of unexpected repairs after your manufacturer’s new vehicle limited warranty expires. The manufacturer stands behind only the manufacturer’s Service Contracts. If you purchased a manufacturer’s Service Contract, you will receive Plan Provisions and an Owner Identification Card in the mail within three weeks of your vehicle delivery date.
IF YOU NEED CONSUMER ASSISTANCE 369 REPORTING SAFETY DEFECTS In the 50 United States and Washington D.C.: If you believe that your vehicle has a defect which could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying the manufacturer.
IF YOU NEED CONSUMER ASSISTANCE • Service Manuals. These comprehensive service manuals provide the information that students and professional technicians need in diagnosing/troubleshooting, problem solving, maintaining, servicing and repairing DaimlerChrysler Corporation vehicles. A complete working knowledge of the vehicle, system and/or components is written in straightforward language with illustrations, diagrams and charts. • Diagnostic Procedure Manuals.
IF YOU NEED CONSUMER ASSISTANCE 371 DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES The following describes the tire grading categories established by the National highway Traffic Safety Administration. The specific grade rating assigned by the tire’s manufacturer in each category is shown on the sidewall of the tires on your car. Traction Grades The traction grades, from highest to lowest, are AA, A, B, and C.
IF YOU NEED CONSUMER ASSISTANCE Temperature Grades The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
INDEX 10
INDEX ABS (Anti-Lock Brake System) . . . . . . . . . . . . . 225 Adding Engine Coolant (Antifreeze) . . . . . . . . . 314 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . 257 Adding Washer Fluid . . . . . . . . . . . . . . 109,110,310 Additives, Fuel . . . . . . . . . . . . . . . . . . . . . . . . 255 Adjustable Pedals . . . . . . . . . . . . . . . . . . . . . . . 98 Air Conditioner Maintenance . . . . . . . . . . . . . . 307 Air Conditioning . . . . . . . . . . . . . . . . . . . . . . .
INDEX 375 Ball Joints . . . . . . . . . . . . . . . . . . . . . . . . . . . . 309 Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 306 Jump Starting . . . . . . . . . . . . . . . . . . . . . . . . 282 Keyless Transmitter Replacement (RKE) . . . . . 24 Location . . . . . . . . . . . . . . . . . . . . . . . . . 283,306 Bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 321 Belts, Drive . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Compass Variance . . . . . . . . . . . . . . . . . . . . . . 155 Computer, Trip/Travel . . . . . . . . . . . . . . . . . . . 153 Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135 Console, Floor . . . . . . . . . . . . . . . . . . . . . . . . . 135 Console, Overhead . . . . . . . . . . . . . . . . . . . . . . 122 Contract, Service . . . . . . . . . . . . . . . . . . . . . . . 368 Coolant Pressure Cap . . . . . . . . . . . . . . . . . . . . 314 Cooling System . . . . . . . . .
INDEX 377 Hazard Warning Flasher . . . . . . . . . . . . . . . . 274 Jacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 275 Jump Starting . . . . . . . . . . . . . . . . . . . . . . . . 282 Overheating . . . . . . . . . . . . . . . . . . . . . . . . . 274 Towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 286 Emission Control System Maintenance . . . . 296,350 Engine . . . . . . . . . . . . . . . . . . . . . . . . . 292,293,294 Air Cleaner . . . . . . . . . . . . . . . . . . .
INDEX Cooling System . . . . . . . . . . . . . . . . . . . . . . . 312 Engine Oil . . . . . . . . . . . . . . . . . . . . . . . 298,299 Power Steering . . . . . . . . . . . . . . . . . . . . . . . 309 Fluids . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 346 Fluids, Lubricants and Genuine Parts . . . . . . . . 346 Fog Lights . . . . . . . . . . . . . . . . . . . . . . . . . 105,143 Folding Rear Seat . . . . . . . . . . . . . . . . . . . . . . . 94 Freeing A Stuck Vehicle . . . . . . . .
INDEX 379 On With Wipers . . . . . . . . . . . . . . . . . . . 103,108 Passing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106 Switch . . . . . . . . . . . . . . . . . . . . . . . . . . 102,103 Time Delay . . . . . . . . . . . . . . . . . . . . . . . . . . 105 Washers . . . . . . . . . . . . . . . . . . . . . . . . . 110,310 Heated Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 Heater, Engine Block . . . . . . . . . . . . . . . . . . . .
INDEX Lap/Shoulder Belts . . . . . . . . . . . . . . . . . . . . . . 32 LATCH (Lower Anchors and Tether for CHildren) . . . . . 56 Latch Plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Latches Hood . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99 Lead Free Gasoline . . . . . . . . . . . . . . . . . . . . . . 253 Life of Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . 249 Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61,100 Airbag . . . . .
INDEX 381 Lower Anchors and Tether for CHildren (LATCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 Lubrication, Body . . . . . . . . . . . . . . . . . . . . . . . 309 Lumbar Support . . . . . . . . . . . . . . . . . . . . . . . . 92 Maintenance Free Battery . . . . . . . . . . . . . . . . . 306 Maintenance Procedures . . . . . . . . . . . . . . . . . . 298 Maintenance Schedule . . . . . . . . . . . . . . . . . . . 350 Schedule “A” . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Synthetic . . . . . . . . . . . . . . . . . . . . . . . . . . . 302 Viscosity . . . . . . . . . . . . . . . . . . . . . . . . . 301,344 Onboard Diagnostic System . . . . . . . . . . . . 295,296 Opener, Garage Door (HomeLink威) . . . . . . . . . 123 Operator Manual (Owner’s Manual) . . . . . . . . . . 4 Overhead Console . . . . . . . . . . . . . . . . . . . . . . 122 Overheating, Engine . . . . . . . . . . . . . . . . . . 146,274 Owner’s Manual (Operator Manual) . . . . . . . 4,369 Panic Alarm . .
INDEX 383 Radio (Sound Systems) . . . . . . . . . . . . . . . . 164,171 Rain Sensitive Wiper System . . . . . . . . . . . . . . 107 Rear Park Assist System . . . . . . . . . . . . . . . . . . 114 Rear Seat, Folding . . . . . . . . . . . . . . . . . . . . . . . 94 Rear Window Defroster . . . . . . . . . . . . . . . . . . 193 Rearview Mirrors . . . . . . . . . . . . . . . . . . . . . . . . 67 Reclining Front Seats . . . . . . . . . . . . . . . . . . . . . 91 Recorder, Event Data . . . . . . . . . . . . . . .
INDEX Rear Folding . . . . . . . . . . . . . . . . . . . . . . . . . 94 Reclining . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91 Security Alarm (Theft Alarm) . . . . . . . . . . . . . . . 25 Selection of Coolant (Antifreeze) . . . . . . . . . 313,346 Self-Sealing Tires . . . . . . . . . . . . . . . . . . . . . . . 229 Sentry Key (Immobilizer) . . . . . . . . . . . . . . . . . . 12 Service Assistance . . . . . . . . . . . . . . . . . . . . . . 366 Service Contract . . . . . . . . . . . . . .
INDEX 385 Temperature Gauge, Engine Coolant . . . . . . 146,275 Theft Alarm (Security Alarm) . . . . . . . . . . . . . . . 25 Theft System (Security Alarm) . . . . . . . . . . . . . . 25 Tie Down Hooks, Cargo . . . . . . . . . . . . . . . . . . 135 Tilt Steering Column . . . . . . . . . . . . . . . . . . 111,112 Tire and Loading Information Placard . . . . . . . 239 Tire Identification Number (TIN) . . . . . . . . . . . 238 Tire Markings . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Trailer Towing . . . . . . . . . . . . . . . . . . . . . . . . . 262 Cooling System Tips . . . . . . . . . . . . . . . . . . . 272 Hitches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 264 Minimum Requirements . . . . . . . . . . . . . . . . 267 Trailer and Tongue Weight . . . . . . . . . . . . . . 266 Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 269 Trailer Towing Guide . . . . . . . . . . . . . . . . . . . . 264 Trailer Weight . . . . . . . . . . . . . . . . . .
INDEX 387 Wheel and Wheel Trim . . . . . . . . . . . . . . . . . . . 323 Wheel Bearings . . . . . . . . . . . . . . . . . . . . . . . . 321 Wind Buffeting . . . . . . . . . . . . . . . . . . . . . . 29,130 Window Airbag (Side Curtain) . . . . . . . . . . . . 40,47 Window Fogging . . . . . . . . . . . . . . . . . . . . 195,202 Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Windshield Defroster . . . . . . . . . . .
NOTES
NOTES
NOTES
NOTES
NOTES
