SECTION TABLE OF CONTENTS PAGE 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 3 4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION CONTENTS 䡵 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 How To Use This Manual . . . . . . . . . . . . . . . . . 4 䡵 Warnings And Cautions . . . . . . . . . . . . . . . . . . 6 䡵 Vehicle Identification Number . . . . . . . . . . . . . . 6 ▫ Partial Zero Emission Vehicle (PZEV) For 2.4L — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 7 䡵 Vehicle Modifications / Alterations . . . . . . . . . .
INTRODUCTION INTRODUCTION This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a Warranty Information Booklet and various customer oriented documents. You are urged to read these publications carefully. Following the instructions and recommendations in this manual will help assure safe and enjoyable operation of your vehicle.
INTRODUCTION 5 1
INTRODUCTION WARNINGS AND CAUTIONS This manual contains WARNINGS against operating procedures which could result in an accident or bodily injury. It also contains CAUTIONS against procedures which could result in damage to your vehicle. If you do not read this entire manual you may miss important information. Observe all Warnings and Cautions.
INTRODUCTION Partial Zero Emission Vehicle (PZEV) for 2.4L — If Equipped NOTE: If the 8th digit of the vehicle identification number (VIN) contains a ⬙J⬙ then your vehicle is equipped with the Partial Zero Emissions Vehicle (PZEV) package. NOTE: There are specific instructions regarding when to change the ignition cables and spark plugs with the PZEV package. Please refer to the Maintenance Schedules section in your owner’s manual for specific maintenance instructions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS 䡵 A Word About Your Keys . . . . . . . . . . . . . . . . .11 ▫ Central Locking — If Equipped . . . . . . . . . . . .17 ▫ Ignition Key Removal . . . . . . . . . . . . . . . . . . .11 ▫ Door Ajar Warning . . . . . . . . . . . . . . . . . . . . .17 ▫ Automatic Transaxle Ignition Interlock System . .12 ▫ Automatic (Rolling) Door Locks . . . . . . . . . . . .17 ▫ Key-In-Ignition Reminder . . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ To Use The Panic Alarm . . . . . . . . . . . . . . . . .21 ▫ Seat Belt Pretensioners . . . . . . . . . . . . . . . . . . .31 ▫ To Program Additional Transmitters . . . . . . . . .21 ▫ Enhanced Driver Seat Belt Reminder System (BeltAlert) . . . . . . . . . . . . . . . . . . . . . . . . . . .32 ▫ General Information . . . . . . . . . . . . . . . . . . . .21 ▫ Transmitter Battery Service . . . . . . . . . . . . . . .22 䡵 Vehicle Theft Alarm . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS You can insert the double sided keys into the locks with either side up. 11 Ignition Key Removal 2 The dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys from your dealer. Ask your dealer for these numbers and keep them in a safe place.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: If you try to remove the key before you place the lever in PARK, the key may become trapped temporarily in the key cylinder. If this occurs, rotate the key clockwise slightly, then remove the key as described. If a malfunction occurs, the system may trap the key in the ignition cylinder to warn you that this safety feature is inoperable. The engine can be started and stopped but the key cannot be removed until you obtain service.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE SENTRY KEY — IF EQUIPPED With this system, an electronically coded ignition key sends a signal to the vehicle electronics. If the electronics recognizes the signal, the vehicle will start and continue to run. If the system does not recognize the signal the vehicle will start and run for 2 seconds then shut off.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE At the time of purchase, the original owner is provided with a four digit PIN number. This number is required for dealer replacement of keys. Duplication of keys may be performed at an authorized dealer or by using the Customer Key Programming procedure. This procedure consists of programming a blank key to the vehicle electronics. A blank key is one which has never been programmed. Turn the ignition Off and remove the second key.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ILLUMINATED ENTRY SYSTEM The interior lights will come on when you open any door, unlock the vehicle with the remote keyless entry (if so equipped) or central unlock (if so equipped). They will remain on for about 30 seconds after all doors are closed then fade to off. The lights also will turn off if you turn on the ignition after you close all doors.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Power Door Locks There is a door lock switch on each front door trim panel located to the front of the door handle. Press this switch to lock or unlock the four doors. Door Lock Plunger If the door lock plunger is down when you shut the door, the door will lock. Therefore, make sure that the keys are not inside the vehicle before closing the door.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Central Locking — If Equipped All vehicle doors are locked with the first turn of the key to the LOCK position. The double activation feature requires you to turn the key in the cylinder lock two times within five seconds to UNLOCK all vehicle doors at once. The Automatic Door Locks can be disabled or re-enabled by performing the following procedure: 1. Close all doors and place the key in the ignition. 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Depress the power door lock switch to lock the doors. 1. Close all doors and place the key in the ignition. 2. Cycle the ignition switch between OFF and ON/RUN and back to OFF 4 times ending up in the OFF position. 3. Depress the power door lock switch to unlock the doors. 4. A single chime will indicate the completion of the programming. Power Door Lock Switch 4. A single chime will indicate the completion of the programming.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Avoid trapping anyone in the vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged. 19 NOTE: For emergency exit with the system engaged, move the lock plunger up (unlocked position), lower the window and open the door with the outside door handle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: The system may be programmed to unlock all the doors upon the first press of the Unlock button. To toggle between the first press unlock of the driver’s door to unlock of all doors, perform the following procedure: 1. Press and hold the Unlock button on the transmitter. 2. Continue to hold the Unlock button, wait at least 4 but no longer than 10 seconds, then press the LOCK button. 3. Release both buttons.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Continue to hold the Unlock button, wait at least 4 but no longer than 10 seconds, then press the Trunk button. 3. Release both buttons. Panic Alarm The panic mode unlocks the driver’s door, turns on the interior lights, flashes the headlights, and sounds the horn for about 3 minutes or until the alarm is turned off. To use the Panic Alarm: Press and hold the Panic Button for at least 1 second to activate the panic alarm.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. This device must accept any interference that may be received, including interference that may cause undesired operation If your Remote Lock Control fails to operate from a normal distance, check for these two conditions: 1. Weak batteries in transmitter. The expected life of batteries is from one to two years 2. Closeness to a radio transmitter such as a radio station tower, airport transmitter, and some mobile or CB radios.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE VEHICLE THEFT ALARM The system monitors the doors, trunk, and ignition for unauthorized operation. If something triggers the alarm, the system will signal for up to 18 minutes. For the first three minutes the horn will sound and the headlights and interior lights will flash. Then the horn will stop and if the source of the trigger is still present, the lights will continue to flash for another 15 minutes.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE TRUNK LOCK AND RELEASE With the ignition ON, the word “deck” will be displayed in place of the odometer display indicating that the trunk is open. The odometer display will reappear once the trunk is closed or if the trip button is depressed. With the key in lock position or key out, the “deck” will be displayed until the trunk is closed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Trunk Internal Emergency Release 25 WINDOWS Power Windows 2 Emergency Release NOTE: As a security measure, a Trunk Internal Emergency Release lever is built into the trunk latching mechanism. In the event of an individual being locked inside the trunk, the trunk can be simply opened by pulling on the glow-in-the-dark handle attached to the trunk latching mechanism. See picture.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Never leave children in a vehicle, with the keys in the ignition switch. Occupants, particularly unattended children, can become entrapped by the power windows while operating the power window switch. Such entrapment may result in serious injury or death. The window controls on the driver’s door operate all windows. The driver’s window switch has an Auto Down feature.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Please pay close attention to the information in this section. It tells you how to use your restraint system properly to keep you and your passengers as safe as possible. WARNING! In a collision, you and your passengers can suffer much greater injuries if you are not properly buckled up. You can strike the interior of your vehicle or other passengers, or you can be thrown out of the vehicle. Always be sure you and others in your vehicle are buckled up properly.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and can take the forces of a collision the best. Wearing your belt in the wrong place could make your injuries in a collision much worse. You might suffer internal injuries, or you could even slide out of part of the belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you as well. In a sudden stop you could move too far forward, increasing the possibility of injury. Wear your seat belt snugly. • A belt that is worn under your arm is very dangerous.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as possible and keep it snug. • A twisted belt can’t do its job as well. In a collision it could even cut into you. Be sure the belt is straight. If you can’t straighten a belt in your vehicle, take it to your dealer and have it fixed. 5.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Adjustable Upper Shoulder Belt Anchorage In the driver and front passenger seats, the shoulder belt can be adjusted upward or downward to position the belt away from your neck. Push the lever above the webbing upward to release the anchorage, and then move it up or down to the position that serves you best. 31 In the rear seat, move toward the center of the seat to position the belt away from your neck.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Enhanced Driver Seat Belt Reminder System (BeltAlert) If the driver’s seat belt has not been buckled within 60 seconds of starting the vehicle and if the vehicle speed is greater than 5 mph (8 km/h), the Enhanced Warning System (BeltAlert) will alert the driver to buckle their seat belt. The driver should also instruct all other occupants to buckle their seat belts.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Turn off the engine. A single chime will sound to signify that you have successfully completed the programming. The Enhanced Warning System (BeltAlert) can be reactivated by repeating this procedure. NOTE: Although the Enhanced Warning System (BeltAlert) has been deactivated, the Seat Belt Warning Light will continue to illuminate while the driver’s seat belt remains unbuckled.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Driver and Right Front Passenger Supplemental Restraint System (SRS) - Airbag This vehicle may also be equipped with left and right window bags to protect the driver and passengers sitting next to a window. If the vehicle is equipped with window bags, they are located above the side windows. Their covers are also labeled SRS AIRBAG.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Do not put anything on or around the front airbag covers or attempt to manually open them. You may damage the airbags and you could be injured because the airbags are not there to protect you. These protective covers for the airbag cushions are designed to open only when the airbags are inflating. • If your vehicle is equipped with left and right window bags, do not stack luggage or other cargo up high enough to block the location of the window bag.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Children that are not big enough to properly wear the vehicle seat belt (see section on “Child Restraint”) should be secured in the rear seat in child restraints or beltpositioning booster seats. Older children who do not use child restraints or beltpositioning booster seats should ride properly buckled up in the rear seat. Never allow children to slide the shoulder belt behind them or under their arm.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • AIRBAG Readiness Light • Driver Airbag • Passenger Airbag • Steering Wheel and Column • Instrument Panel • Interconnecting Wiring • Knee Impact Bolsters • Left and Right Window Bags Above Side Windows — If Equipped • Left and Right Side Impact Sensors — If Equipped • Driver and Front Passenger Seat Belt Pretensioners How The Airbag System Works • The airbag control module determines if a frontal collision is severe enough to require the airbags to inflate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Ignoring the AIRBAG light in your instrument panel could mean you won’t have the airbags to protect you in a collision. If the light does not come on, stays on after you start the vehicle, or if it comes on as you drive, have the airbag system checked right away. • When the airbag control module detects a collision requiring the airbags, it signals the inflator units. A large quantity of nontoxic gas is generated to inflate the airbags.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE They are not permanent and normally heal quickly. However, if you haven’t healed significantly within a few days, or if you have any blistering, see your doctor immediately. • As the airbags deflate you may see some smoke-like particles. The particles are a normal by-product of the process that generates the nontoxic gas used for airbag inflation. These airborne particles may irritate the skin, eyes, nose, or throat.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE where the window bag inflates. This especially applies to children. The window bag is only about 3 1⁄2 inches (8 3⁄4 cm) thick when it is inflated. Maintaining Your Airbag System WARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. You could be injured because the airbags are not there to protect you.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Children 12 years and under should ride properly buckled up in a rear seat, if available. According to crash statistics, children are safer when properly restrained in the rear seats rather than in the front. WARNING! In a collision, an unrestrained child, even a tiny baby, can become a missile inside the vehicle. The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Rearward-facing child seats must NEVER be used in the front seat of a vehicle with the front passenger airbag unless the airbag is turned off. An airbag deployment could cause severe injury or death to infants in this position. WARNING! • Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: For additional information refer www.seatcheck.org or call 1–866–SEATCHECK. to Older Children and Child Restraints Children who weigh more than 20 lbs (9 kg) and who are older than one year can ride forward-facing in the vehicle. Forward-facing child seats and convertible child seats used in the forward-facing direction are for children who weigh 20 to 40 lbs (9 to 18 kg) and who are older than one year.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE the child restraint using lower anchorages and upper tether straps from the child restraint to the vehicle structure. LATCH-compatible child restraint systems are now available. However, because the lower anchorages are to be introduced over a period of years, child restraint systems having attachments for those anchorages will continue to also have features for installation using the vehicle’s seat belts.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Installing the LATCH-Compatible Child Restraint System We urge that you carefully follow the directions of the manufacturer when installing your child restraint. Not all child restraint systems will be installed as described here. Again, carefully follow the installation instructions that were provided with the child restraint system.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE restraint. Finally, tighten all three straps as you push the child restraint rearward and downward into the seat, removing slack in the straps according to the child restraint manufacturer’s instructions. WARNING! Improper installation of a child restraint to the LATCH anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Child restraint tether strap attachment 1. Rotate the cover over the anchor directly behind the seat where you are placing the child restraint. 47 between the two posts. If not possible, lower the head restraint and pass the tether strap around the outboard side of the head restraint. 3. Attach the tether strap hook (A) of the child restraint to the anchor (B) and remove slack in the tether strap according to the child restraint manufacturer’s instructions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Pets should be restrained in the rear seat in pet harnesses or pet carriers that are secured by seat belts. ENGINE BREAK-IN RECOMMENDATIONS The engine in your new vehicle does not require a long break-in period. Drive moderately during the first 300 miles (500 km). After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • To avoid drawing exhaust gases into the vehicle, close the trunk while driving. However, if for some reason it must remain open, close all windows. Adjust the heating or cooling system to force outside air into the vehicle. Set the blower at high speed. Safety Checks You Should Make Inside the Vehicle Seat Belts Inspect the belt system periodically, checking for cuts, frays and loose parts. Damaged parts must be replaced immediately.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 3 䡵 Console Features . . . . . . . . . . . . . . . . . . . . . . .54 䡵 Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59 ▫ Console Features — Without Heated Seats . . . .54 ▫ Manual Front Seat Adjustments . . . . . . . . . . . .59 ▫ Console Features — With Heated Seats . . . . . . .55 ▫ Power Seats — If Equipped . . . . . . . . . . . . . . .60 䡵 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Multi-Function Control Lever . . . . . . . . . . . . . .66 䡵 Electronic Speed Control— If Equipped . . . . . .71 ▫ Headlights, Parking Lights, Instrument Panel Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66 ▫ To Activate . . . . . . . . . . . . . . . . . . . . . . . . . . .72 ▫ Automatic Headlights—If Equipped . . . . . . . . .67 ▫ Daytime Running Lights (Canada Only) . . . . . .67 ▫ Lights-On Reminder . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 53 䡵 Power Sunroof — If Equipped . . . . . . . . . . . . .79 ▫ Sunshade Operation . . . . . . . . . . . . . . . . . . . .81 ▫ Opening Sunroof - Manual . . . . . . . . . . . . . . .80 ▫ Wind Buffeting . . . . . . . . . . . . . . . . . . . . . . . .81 ▫ Opening Sunroof - Express . . . . . . . . . . . . . . .80 ▫ Sunroof Maintenance . . . . . . . . . . . . . . . . . . . .81 ▫ Closing Sunroof - Manual . . . . . . . . . . . . . . . .80 ▫ Sunroof Fully Closed .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONSOLE FEATURES Console Features — Without Heated Seats The center console/armrest has a pencil /tire gage holder and a tissue holder mounted on the underside of the cover. The bottom of the console bin also has built in holders for compact discs or cassette tapes. There are also two cup holders for rear seat passengers located directly in the back of the center console. Two coin holders are located toward the front of the inside of the console bin.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Console Features — With Heated Seats Console The front console has two cup holders. An optional removable ashtray may be located in the driver’s side cup holder. 55 The center console/armrest has a pencil /tire gage holder and a tissue holder mounted on the underside of the cover. The bottom of the console bin also has built in holders for compact discs or cassette tapes. The power outlet is also mounted inside the center console (if equipped).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Day/Night Mirror— If Equipped Adjust the mirror to center on the view through the rear window. A two point pivot system allows for horizontal and vertical mirror adjustment. Automatic Dimming Mirror— If Equipped This mirror will automatically adjust for annoying headlight glare from vehicles behind you. Push in the button on the face of the mirror to activate the dimming feature.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 57 CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean. 3 Electric Remote-Control Mirrors— If Equipped Both of the outside mirrors can be adjusted by using the remote controls mounted on the instrument panel to the left of the steering wheel.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Outside Mirror — Passenger’s Side Adjust the convex outside mirror so you can just see the side of your vehicle in the part of the mirror closest to the vehicle. Illuminated Vanity Mirrors — If Equipped An illuminated vanity mirror is on each sun visor. To use the mirror, rotate the sun visor down and swing the mirror cover upward. The lights will turn on automatically. Closing the mirror cover turns off the lights.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE SEATS Manual Front Seat Adjustments Forward/Rearward The adjusting bar is at the front of the seats, near the floor. Pull the bar up to move the seat to the desired position. 59 Reclining Bucket Seats The recliner control is on the side of the seat. To recline, lean forward slightly before lifting the lever, then lean back to the desired position and release the lever. Lean forward and lift the lever to return the seatback to its normal position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Lumbar Support — If Equipped This feature allows you to increase or decrease the amount of lumbar support. The control lever is located on the inboard side of the driver’s seatback. Turn the control lever forward to increase and rearward to decrease the desired amount of lumbar support. Power Seats — If Equipped The power seat switches are on the outboard side of the seat near the floor.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Heated Seats — If Equipped This feature heats the front driver and passenger seats on models equipped with leather seats. The controls for the heated seats are located in the floor console next to the parking brake. Adjustable Head Restraints Head restraints can reduce the risk of whiplash injury in the event of impact from the rear. Adjust the restraints so that the upper edge is as high as practical. To raise, pull up on the head restraint.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Folding Rear Seat To provide additional storage area, the rear seatback can be folded forward. Pull on the loops shown in the picture to fold down either or both seatbacks. When returning the rear seat back to the upright position be sure the seat back is latched.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 63 TO OPEN AND CLOSE THE HOOD To open the hood, two latches must be released. First pull the hood release lever located under the left side of the instrument panel. 3 Hood Safety Catch Use the hood prop rod to secure the hood in the open position. Place the upper end of the prop rod in the hole marked “prop” on the underside of the hood.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! If the hood is not fully latched it could fly up when the vehicle is moving and block your forward vision. You could have a collision. Be sure all hood latches are fully latched before driving.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Daytime Mode (Daytime Brightness Feature) Rotate the dimmer control to the first detent (full-circle). This feature brightens the odometer and radio display when the parking lights or headlights are on during daylight conditions. 3 Front Map/Reading Lights — If Equipped These lights are mounted between the sun visors. Each light has a push-on push-off switch.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Multi-Function Control Lever Multi-Function Lever Multi-Function Lever The Multi-Function lever controls the operation of the headlights, turn signals, headlight beam select switch, instrument panel light dimming, courtesy lights, passing lights, dome light and fog lights. Headlights, Parking Lights, Instrument Panel Lights Turn the end of the Multi-Function lever to the first detent for parking light operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Headlights—If Equipped This system automatically turns your headlights on at a preset level of outdoor lighting. Turn the end of the control lever to the third detent to turn the system on. When the system is on, the headlight delay feature is also on. This means that your headlights will stay on for about 90 seconds after you turn the ignition switch off. To turn the Automatic system off, turn the control lever clockwise, to the off position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Headlight Beam Select Switch Pull the turn signal lever towards you to switch the headlights to HIGH beam. Pull the turn signal lever a second time to switch the headlights to LOW beam. WINDSHIELD WIPERS AND WASHERS The wipers and washers are operated by a switch in the right side control lever. Turn the end of the control lever to select the desired wiper speed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To use the washer, pull the lever toward you and hold while spray is desired. If the lever is pulled while in the delay range, the wiper will operate for several cycles after the lever is released, and then resume the intermittent interval previously selected. If the lever is pulled while in the OFF position, the wipers will operate for several cycles, then turn OFF. WARNING! Sudden loss of visibility through the windshield could lead to an accident.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE TILT STEERING COLUMN To tilt the column, push down on the lever below the turn signal control and move the wheel up or down, as desired. Push the lever back up to lock the column firmly in place. Tilt Steering Column Control WARNING! Tilting the steering column while the vehicle is moving is dangerous. Without a stable steering column, you could lose control of the vehicle and have an accident. Adjust the column only while the vehicle is stopped.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE TRACTION CONTROL— IF EQUIPPED To turn the Traction Control System Off, press the switch located on the top of the steering column, to the right of the hazard switch, until the Traction Control indicator in the instrument cluster lights up. NOTE: The Traction Control System is enabled each time the ignition switch is turned On. This will occur even if you used the switch to turn the system off before powering down or turning the ignition to Lock.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Activate: Press the ON/OFF switch to turn the speed control system ON. To turn the system OFF, press the ON/OFF switch again. The system should be turned OFF when not in use. The CRUISE Indicator in the instrument cluster will light up when the Speed Control is ON. To Deactivate: A soft tap on the brake pedal, pushing the CANCEL button, or normal brake or clutch pressure will deactivate speed control without erasing the memory.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To decrease speed while speed control is Engaged, press and hold the COAST button. Releasing the button when the desired speed is reached, will establish a new SET speed. Tapping the COAST button once will result in a 1 mph (1.6 km/h) decrease in the SET speed. Each time the button is tapped, the SET speed decreases. For example, tapping the button three times will decrease speed by 3 mph (5 km/h).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rolling Hills The transaxle may downshift into third gear and remain there as the vehicle travels over rolling hills. The transaxle will upshift into fourth gear when the road flattens out. The transaxle will resume its normal shift schedule if you depress the accelerator pedal during any of the above conditions.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 75 WARNING! WARNING! A moving garage door can cause injury to people and pets in the path of the door. People or pets could be seriously or fatally injured. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by federal safety standards. This includes most garage door opener models manufactured after 1982. Do not use a garage door opener without these safety features it could cause injury or death.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Choose one of the three Universal Transceiver buttons to program. Place the hand held controller one to three inches from the Universal Transceiver while keeping its indicator light in view. 5. The indicator light in the Universal Transceiver will begin to flash, first slowly and then rapidly. The rapid flashing indicates successful programming.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 77 On garage door openers with the “Rolling Code” feature, the transmitter code changes after each use to prevent the copying of your code. difficulty in locating the training button, check your garage door opener manual, or call 1-800-355-3515 or, on the Internet, at www.homelink.com. To check if your device is protected by a “Rolling Code” system: 2. Press and hold the training button on the garage door opener head unit.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Canadian Programming/Gate Programming Canadian frequency laws, and the technology of some entry gates, require you to press and release the hand held transmitter button every two seconds during programming Continue to press and hold the Universal Transceiver button while you press and release the hand held transmitter button until the frequency signal has been learned.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 79 1. This device may not cause harmful interference. 2. This device must accept any interference that may be received including interference that may cause undesired operation. 3 NOTE: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. HomeLink威 is a trademark owned by Johnson Controls, Inc.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Never leave children in a vehicle, with the keys in the ignition switch. Occupants, particularly unattended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death. • In an accident, there is greater risk of being thrown from a vehicle with an open sunroof. You could also be seriously injured or killed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 81 Sunshade Operation The sunshade can be opened manually. However, the sunshade will open automatically as the sunroof opens. Sunroof Maintenance Use only a non abrasive cleaner and a soft cloth to clean the glass panel. NOTE: The sunshade cannot be closed if the sunroof is open. Sunroof Fully Closed Press and hold the switch forward until the sunroof stops completely to ensure that the sunroof is fully closed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Electrical Outlet Use With Engine Off • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting. • Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.) will degrade the battery even more quickly.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 Instruments And Controls . . . . . . . . . . . . . . . . .87 䡵 Radio General Information . . . . . . . . . . . . . . . 100 䡵 Instrument Cluster Standard . . . . . . . . . . . . . . .88 ▫ Radio Broadcast Signals . . . . . . . . . . . . . . . . . 100 䡵 Instrument Cluster Premium . . . . . . . . . . . . . . .89 ▫ Two Types Of Signals . . . . . . . . . . . . . . . . . . 100 䡵 Instrument Cluster Description . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Tuning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101 ▫ Changing Tape Direction . . . . . . . . . . . . . . . . 105 ▫ Radio Data System (RDS) . . . . . . . . . . . . . . . 101 ▫ Metal Tape Selection . . . . . . . . . . . . . . . . . . . 105 ▫ PTY (Program Type) Button . . . . . . . . . . . . . . 102 ▫ Pinch Roller Release . . . . . . . . . . . . . . . . . . . 105 ▫ Balance . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 䡵 Sales Code RBB—AM/FM Stereo Radio With Cassette Tape Player And CD Changer Capability . . . . . . . . . . . . . . . . . . . . . . . . . . . 109 ▫ Radio Operation . . . . . . . . . . . . . . . . . . . . . . 109 ▫ Mode Button . . . . . . . . . . . . . . . . . . . . . . . . 111 ▫ Scan Button (Radio Mode) . . . . . . . . . . . . . . . 111 ▫ Cassette Player Features . . . . . . . . . . . . . . . . 112 ▫ CD Changer Control Capability — If Equipped . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 䡵 Remote Sound System Controls — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 122 ▫ Radio Operation . . . . . . . . . . . . . . . . . . . . . . 123 ▫ Tape Player . . . . . . . . . . . . . . . . . . . . . . . . . 123 ▫ CD Player — Single Disc In Radio . . . . . . . . . 124 ▫ CD Player — 6 Disc CD Changer . . . . . . . . . . 124 䡵 Cassette Tape And Player Maintenance . . . . . . 124 䡵 Compact Disc Maintenance . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 87 INSTRUMENTS AND CONTROLS 4
UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER STANDARD
UNDERSTANDING YOUR INSTRUMENT PANEL 89 INSTRUMENT CLUSTER PREMIUM 4
UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTION 1. Fuel Gauge When the ignition key is in the ON position, the pointer will show the level of fuel remaining in the fuel tank. 2. Traction Control — If Equipped This display indicator illuminates momentarily as a bulb check when the ignition switch is first turned ON. The indicator will blink during an active traction event, but will remain solid when the system is deactivated or if a system malfunction occurs.
UNDERSTANDING YOUR INSTRUMENT PANEL 5. Tachometer The red area of the scale shows the maximum permissible engine revolutions-per-minute (rpm x 1000) for each gear range. Before reaching the red area (over 6,500 rpm), ease up on the accelerator to prevent engine over speed. 6. Turn Signal Indicators The arrows will flash in unison with the exterior turn signal, when using the turn signal lever. 7. High Beam Indicator This light shows that the headlights are on high beam.
UNDERSTANDING YOUR INSTRUMENT PANEL through several of your typical driving cycles. In most situations the vehicle will drive normally and will not require towing. The Malfunction Indicator Light flashes to alert to serious conditions that could lead to immediate loss of power or severe catalytic converter damage. The vehicle should be serviced as soon as possible if this occurs. 11. Fog Light Indicator — If Equipped This light shows when the fog lights are ON. 12.
UNDERSTANDING YOUR INSTRUMENT PANEL U.S. federal regulations require that upon transfer of vehicle ownership, the seller certify to the purchaser the correct mileage that the vehicle has been driven. Therefore, if the odometer reading is changed, during repair or replacement, be sure to keep a record of the reading before and after the service so that the correct mileage can be determined. The trip odometer shows individual trip mileage.
UNDERSTANDING YOUR INSTRUMENT PANEL If the light comes on and remains on while driving, stop the vehicle and shut off the engine. Do not operate the vehicle until the cause is corrected. The light does not show the quantity of oil in the engine. This can be determined using the procedure shown in Section 7. 18. Brake System Warning Light This light monitors both the brake fluid level and the parking brake.
UNDERSTANDING YOUR INSTRUMENT PANEL In an ABS equipped vehicle, the Brake System Warning light will come on if the ABS light is not functioning or if the ABS system is not communicating. 19. Seat Belt Reminder Light When the ignition switch is first turned ON, this light will turn on for 5 to 8 seconds as a bulb check. During the bulb check, if the driver’s seat belt is unbuckled, a chime will sound.
UNDERSTANDING YOUR INSTRUMENT PANEL Control Buttons Step Button Use this button to choose or cycle through the five trip conditions. Reset The following trip conditions can be reset: • AVG ECO (changes to present fuel economy) • ODO • ET To reset only the trip condition currently displayed, press and release the STEP and US/M buttons simultaneously until a chime sounds.
UNDERSTANDING YOUR INSTRUMENT PANEL Trip Odometer (ODO) This display shows the distance traveled since the last reset. Elapsed Time (ET) This display shows the accumulated ignition ON time since the last reset. Compass Temperature Display This display provides the outside temperature and one of eight compass readings to indicate the direction the vehicle is facing. WARNING! Even if the display still reads a few degrees above 32°F ( 0°C), the road surface may be icy, particularly in woods or on bridges.
UNDERSTANDING YOUR INSTRUMENT PANEL Manual Compass Calibration Compass calibration can also be requested. To manually calibrate the compass, use the STEP button to step to the compass/ temperature display and then hold down both the STEP and US/M buttons simultaneously until the CAL symbol is displayed. Release the buttons once the CAL symbol appears. Manual compass calibration has been initiated at this point.
UNDERSTANDING YOUR INSTRUMENT PANEL 99 Outside Temperature If the outside temperature is more than 131°F (55°C), the display will show 131°F. When the outside temperature is less than ⫺40°F (⫺40°C), the display will show ⫺40°F/C. CIGAR LIGHTER/ASHTRAY For a nominal charge your dealer can provide a “smoker’s” package. This package consists of a cigar lighter and an ashtray that utilizes one of the cup holders. ELECTRONIC DIGITAL CLOCK The clock and radio each use the display panel built into the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL To Set The Clock: 1. Use a ballpoint pen or similar object to press the hour (H) or minute (M) buttons on the radio, The time setting will increase each time you press the button. 2. Press any other button to exit from the clock setting mode. Or, it will exit the mode automatically if left alone for 5 or 6 seconds. RADIO GENERAL INFORMATION Radio Broadcast Signals Your new radio will provide excellent reception under most operating conditions.
UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE RAZ—AM/ FM STEREO RADIO WITH CASSETTE TAPE PLAYER, CD PLAYER AND CD CHANGER CONTROLS RAZ Radio 101 Seek Button (Radio Mode) Press and release the Seek button to search for the next station in either the AM or FM mode. Press the top of the button to seek up and the bottom to seek down. Holding the button will by pass stations until you release the button. Tuning Press the TUNE control up or down to increase or decrease the frequency.
UNDERSTANDING YOUR INSTRUMENT PANEL which are broadcasting this information. PTY (Program Type) is used to characterize the station’s program material, for example ⬙Rock Music⬙. PTY (Program Type) Button Pressing this button once will turn on the PTY mode for 5 seconds. If no action is taken during the 5 second time out the PTY icon will turn off. Pressing the PTY button within 5 seconds will allow the program format type to be selected. Many radio stations do not currently broadcast PTY information.
UNDERSTANDING YOUR INSTRUMENT PANEL The radio display will flash “SEEK” and the selected PTY program type when searching for the next PTY station. If no station is found with the selected PTY program type, the radio will return to the last preset station. If a preset button is activated while in the PTY (Program Type) mode, the PTY mode will be exited and the radio will tune to the preset station. Pressing PTY, then SCAN will scan the FM Band and stop at all RDS stations.
UNDERSTANDING YOUR INSTRUMENT PANEL Pressing the AM/FM button continues the search in the alternate frequency band. To stop the search, press SCAN a second time. To Set The Radio Push-button Memory When you are receiving a station that you wish to commit to push-button memory, press the SET button. SET 1 will show in the display window. Select the push-button you wish to lock onto this station and press and release that button.
UNDERSTANDING YOUR INSTRUMENT PANEL Fast Forward (FF) Press the FF button up momentarily to advance the tape in the direction that it is playing. The tape will advance until the button is pressed again or the end of the tape is reached. At the end of the tape, the tape will play in the opposite direction. Rewind (RW) Press the RW button momentarily to reverse the tape direction. The tape will reverse until the button is pressed again or until the end of the tape is reached.
UNDERSTANDING YOUR INSTRUMENT PANEL To turn off the Dolby Noise reduction System: Press the Dolby button (button 2) after you insert the tape. The NR light in the display will go off when the Dolby System is off. The Dolby System is automatically reactivated each time a tape is inserted. * ”Dolby” noise reduction manufactured under license from Dolby Laboratories Licensing Corporation. Dolby and the double-D symbol are trademarks of Dolby Laboratories Licensing Corporation.
UNDERSTANDING YOUR INSTRUMENT PANEL Seek Button Press the top of the SEEK button for the next selection on the CD. Press the bottom of the button to return to the beginning of the current selection, or return to the beginning of the previous selection if the CD is within the first 10 seconds of the current selection. EJT CD (Eject) Button Press this button and the disc will unload and move to the entrance for easy removal. The unit will switch to the radio mode.
UNDERSTANDING YOUR INSTRUMENT PANEL Tape CD Button Press this button to select between CD player and Tape player. Disc Down/Program Button 5 Press the DISC down (button 5) button to play the previous disc. Time Button Press this button to change the display from elapsed CD playing time to time of day. Seek Button Press the SEEK up or down to select another track on the same disc. A SEEK symbol will appear on the display. Scan Button Press this button to play the first 10 seconds of each track.
UNDERSTANDING YOUR INSTRUMENT PANEL CD Diagnostic Indicators When driving over a very rough road, the CD player may skip momentarily. Skipping will not damage the disc or the player, and play will resume automatically. 109 SALES CODE RBB—AM/FM STEREO RADIO WITH CASSETTE TAPE PLAYER AND CD CHANGER CAPABILITY As a safeguard and to protect your CD player, one of the following warning symbols may appear on your display. 4 A CD HOT symbol indicates the player is too hot. CD HOT will pause the operation.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Power to operate the radio is supplied through the ignition switch. It must be in the ON or ACC position to operate the radio. Electronic Volume Control The electronic volume control turns continuously (360 degrees) in either direction without stopping. Turning the volume control to the right increases the volume and to the left decreases it. When the audio system is turned on, the sound will be set at the same volume level as last played.
UNDERSTANDING YOUR INSTRUMENT PANEL stations to be locked into push-button memory. The stations stored in SET 2 memory can be selected by pressing the push-button twice. Every time a preset button is used a corresponding button number will be displayed. Audio The audio button controls the BASS, TREBLE, BALANCE, and FADE. Press the AUDIO button and BASS will be displayed. Press the SEEK + or SEEK – to increase or decrease the Bass tones. Press the AUDIO button a second time and TREB will be displayed.
UNDERSTANDING YOUR INSTRUMENT PANEL Cassette Player Features With ignition OFF and the sound system OFF, you can eject the tape cassette by pushing the EJECT button. You can turn the tape player ON by inserting a cassette or activating the MODE button (with a cassette in the radio), but only when the ignition and radio are on. Each time a cassette is inserted the tape player will begin playing on the side of the cassette that is facing up in the player.
UNDERSTANDING YOUR INSTRUMENT PANEL 113 When Dolby is ON, the NR symbol appears on the display. Each time a tape is inserted the Dolby will turn ON. Seek Button Press the SEEK up or down to select another track on the same disc. A SEEK symbol will appear on the display. * “Dolby” noise reduction manufactured under license from Dolby Laboratories Licensing Corporation. Dolby and the double-D symbol are trademarks of Dolby Laboratories Licensing Corporation.
UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions - Satellite Radio Mode (If Equipped) Refer to the Satellite Radio section of the Owner’s Manual. CD Diagnostic Indicators When driving over a very rough road, the CD player may skip momentarily. Skipping will not damage the disc or the player, and play will resume automatically.
UNDERSTANDING YOUR INSTRUMENT PANEL 115 NOTE: Power to operate the radio is supplied through the ignition switch. It must be in the ON or ACC position to operate the radio. seconds after pressing the SET button, the station will continue to play but will not be locked into push-button memory. Seek Press and release the SEEK button to search for the next station in either the AM or FM mode. Press the top of the button to seek up and the bottom to seek down.
UNDERSTANDING YOUR INSTRUMENT PANEL Press the AUDIO button a second time and TREB will be displayed. Press the SEEK + or SEEK – to increase or decrease the Treble tones. Press the AUDIO button a third time and BAL will be displayed. Press the SEEK + or SEEK – to adjust the sound level from the right or left side speakers. Press the AUDIO button a fourth time and FADE will be displayed. Press the SEEK + or SEEK – to adjust the sound level between the front and rear speakers.
UNDERSTANDING YOUR INSTRUMENT PANEL Inserting The Compact Disc CAUTION! This CD player will accept 4 3⁄4 inch (12 cm) discs only. The use of other sized discs may damage the CD player mechanism. You may either insert or eject a disc with the radio OFF. If you insert a disc with the ignition ON and the radio OFF, the display will show the time of day. If the power is ON, the unit will switch from radio to CD mode and begin to play when you insert the disc.
UNDERSTANDING YOUR INSTRUMENT PANEL Press the RND (button 4) button a second time to stop Random Play. Mode Press the MODE button repeatedly to select between the CD player, the optional remote CD changer and the Satellite Radio (if equipped). When Satellite Radio (if equipped) is selected “SAT” will appear in your radio display. A CD or tape may remain in the player while in the Satellite mode. Time Press the TIME button to change the display from elapsed CD playing time to time of day.
UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions - Satellite Radio Mode (If Equipped) Refer to the Satellite Radio section of the Owner’s Manual. 119 • Water condensation on optics SALES CODE RB1—AM/FM STEREO RADIO WITH DVD/GPS NAVIGATION SYSTEM CD Diagnostic Indicators When driving over a very rough road, the CD player may skip momentarily. Skipping will not damage the disc or the player, and play will resume automatically.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: If your vehicle is not equipped with the CD Changer option, you will not be able to use the Navigation system and the CD Player simultaneously. Always remove the Navigation DVD before inserting another disc. 6 DISC CD CHANGER — IF EQUIPPED The CD changer is located below the radio in the instrument panel. The changer plays only 4 3⁄4 inch (12 cm) discs. The changer holds up to 6 discs.
UNDERSTANDING YOUR INSTRUMENT PANEL Playing Discs The radio will show the CD number, the CD track number, and the Track Time Elapsed while the radio is in the CD mode. If more than one CD is loaded in the changer, the changer will automatically play the next disc after playing the last track of the current disc. Seek Button Press the top of this button on the radio once to play the next track. Press the bottom of the button once to return to the beginning of the current track.
UNDERSTANDING YOUR INSTRUMENT PANEL Time Button Press this button to switch between time of day and CD track time. Changing Modes While in the radio mode, if a cassette is loaded, press the Mode button to switch to the tape mode. If a CD is loaded, press the Mode button to select the CD mode. If neither a tape nor CD is loaded, the radio will ignore the command. • Inserting either a tape or CD automatically starts that mode of play.
UNDERSTANDING YOUR INSTRUMENT PANEL 123 The left hand control is a rocker type switch with a push-button in the center. The function of the left hand control is different depending on which mode you are in. The following describes the left hand control operation in each mode. Radio Operation Pressing the top of the switch will “Seek” up for the next listenable station and pressing the bottom of the switch will “Seek” down for the next listenable station.
UNDERSTANDING YOUR INSTRUMENT PANEL The button in the center of the left hand switch has no function in this mode. If you press the switch up or down twice it plays the second track, three times, it will play the third, etc. CD Player — Single Disc in Radio Pressing the top of the switch once will go to the next track on the CD.
UNDERSTANDING YOUR INSTRUMENT PANEL Maintain your cassette tape player. The head and capstan shaft in the cassette player can pick up dirt or tape deposits each time a cassette is played. The result of deposits on the capstan shaft may cause the tape to wrap around and become lodged in the tape transport. The other adverse condition is low or “muddy” sound from one or both channels, as if the treble tone control were turned all the way down.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: If you experience difficulty in playing a particular disc, it may be damaged, oversized, or have theft protection encoding. Try a known good disc before considering disc player service. You may have a problem with CD-R (recordable) and CD-RW (recordable and writable) disks. RADIO OPERATION AND CELLULAR PHONES Under certain conditions, the operation of a cellular phone in your vehicle can cause erratic or noisy performance from your radio.
UNDERSTANDING YOUR INSTRUMENT PANEL Interior ATC Sensors There are two interior sensors in the vehicle. The Sun Sensor is mounted in the center of the instrument panel near the windshield glass. The In-Car Temperature Sensor is mounted behind the ATC control panel. These sensors transmit data on sun strength and vehicle interior temperatures to enhance system performance. CAUTION! Do not cover either sensor with any foreign material as improper operation of the system will result.
UNDERSTANDING YOUR INSTRUMENT PANEL Comfort Control Use this control to regulate the comfort inside the passenger compartment. Press the top of the switch to raise the temperature selection and the bottom of the switch to lower it. The comfort setting range is from Low, 60, 61,....to 89,90, Hi, for automatic temperature control. You can select a very hot or cold comfort setting by holding the comfort control until it reaches its highest or lowest levels.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: The Recirc button light will blink if you try to use it in the Mix or Defrost modes. Air Direction Buttons (Mode) These buttons allow you to select from five air distribution patterns. These buttons should be used only when you can not achieve comfort or visibility in Auto operation. A symbol in the display window will show which mode is operating. Panel Air is directed through the outlets in the instrument panel. These outlets can be adjusted to direct air flow.
UNDERSTANDING YOUR INSTRUMENT PANEL Windshield Defrost Air is directed through the defrost outlets and side window demist outlets. A small amount of air also is directed through the floor outlets. Use this mode with maximum fan and comfort level settings for best windshield and side window defrosting. The defrost symbol will glow in amber to show that the defroster is on. NOTE: The air conditioning compressor is on in this mode. This dehumidifies the air to help dry the windshield.
UNDERSTANDING YOUR INSTRUMENT PANEL Hot Weather Automatic Recirculation The system will automatically recirculate the air inside the vehicle when the interior is very warm. This will provide maximum cooling. The system will also occasionally return to REC on hot, humid or very hot, dry days to maintain occupant comfort. Side Window Demisters Side window demisters are located on the instrument panel.
UNDERSTANDING YOUR INSTRUMENT PANEL Operating Tips (ATC only)
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: If the system is in the AUTO mode and the fan control is already rotated fully clockwise or fully counterclockwise, the control may have to be rotated to the middle and then to the desired fan setting for manual adjustment of fan speed. Manual Air Conditioning/Heater Control — If Equipped The Air Conditioning System allows you to balance the temperature, amount, and direction of air circulating throughout the vehicle.
UNDERSTANDING YOUR INSTRUMENT PANEL Slight changes in engine speed or power may be noticed when the air conditioning compressor is on. This is a normal occurrence as the compressor will cycle on and off to maintain comfort and increase fuel economy. NOTE: If your air conditioning performance seems lower than expected, check the front of the air conditioning condenser for an accumulation of dirt or insects. The air conditioning condenser is located in front of the radiator.
UNDERSTANDING YOUR INSTRUMENT PANEL • Panel — Air Conditioning Outside air flows through the air conditioning system and then through the outlets located in the instrument panel. • Floor • Bi-Level — Air Conditioning Outside air flows through the air conditioning system and then through the outlets located in both the instrument panel and floor outlets. • Mix • Panel Air is directed through the outlets in the instrument panel. These outlets can be adjusted to direct air flow.
UNDERSTANDING YOUR INSTRUMENT PANEL Rear Seat Outlets These outlets are located under the front seats and direct warm air to the rear seat passengers. Air is directed through these outlets when you select either the Floor, Bi-Level, or Mix modes. Rear Window Defroster The Rear Window Defroster button is located to the right of the Mode Control. Press this button once to turn on the Rear Window Defrost and a second time to turn them off. A light above the button shows that the defroster is on.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Do not use the recirculation mode as it will not clear windows under these conditions. Summer Operation Air conditioned vehicles must be protected with a highquality antifreeze coolant to provide proper corrosion protection and to raise the boiling point of the coolant for protection against overheating. A 50 % concentration is recommended.
UNDERSTANDING YOUR INSTRUMENT PANEL Operating Tips (Manual A/C Control Only)
UNDERSTANDING YOUR INSTRUMENT PANEL 139 Outside Air Intake Make sure the air intake, directly in front of the windshield, is free of ice, slush, snow or other obstructions such as leaves. Leaves collected in the air-intake plenum may reduce air flow and plug the plenum water drains.
STARTING AND OPERATING CONTENTS 䡵 Starting Procedures . . . . . . . . . . . . . . . . . . . . 144 ▫ Automatic Transaxle . . . . . . . . . . . . . . . . . . . 144 ▫ Normal Starting . . . . . . . . . . . . . . . . . . . . . . 144 ▫ Extreme Cold Weather (Below -20°F Or -29°C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145 ▫ If Engine Fails To Start . . . . . . . . . . . . . . . . . 146 ▫ After Starting . . . . . . . . . . . . . . . . . . . . . . . .
STARTING AND OPERATING 䡵 Tire Safety Information . . . . . . . . . . . . . . . . . . 156 䡵 Snow Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . 171 ▫ Tire Markings . . . . . . . . . . . . . . . . . . . . . . . . 156 䡵 Tire Rotation Recommendations . . . . . . . . . . . 172 ▫ Tire Identification Number (TIN) . . . . . . . . . . 159 䡵 AutoStick — If Equipped . . . . . . . . . . . . . . . . 173 ▫ Tire Loading And Tire Pressure . . . . . . . . . . . 160 ▫ AutoStick Operation . . . . . .
STARTING AND OPERATING 143 䡵 Vehicle Loading . . . . . . . . . . . . . . . . . . . . . . . 179 ▫ Fuel Requirements . . . . . . . . . . . . . . . . . . . . 182 䡵 Trailer Towing . . . . . . . . . . . . . . . . . . . . . . . . 179 ▫ Selection Of Engine Oil . . . . . . . . . . . . . . . . . 182 ▫ Towing Requirements . . . . . . . . . . . . . . . . . . 180 ▫ Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184 䡵 Flexible Fuel – (2.7L Engines With Automatic Transmission Only) . . . . . . .
STARTING AND OPERATING STARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. Automatic Transaxle The gear selector must be in the NEUTRAL or PARK position before you can start the engine. Apply the brakes before shifting to any driving gear. CAUTION! Normal Starting Normal Starting of either a cold or a warm engine does not require pumping or depressing the accelerator pedal.
STARTING AND OPERATING 145 CAUTION! Ignition Key Positions WARNING! Never pour fuel or other flammable liquid into the throttle body air inlet opening in an attempt to start the vehicle. This could result in flash fire causing serious personal injury. Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transaxle cannot be started this way.
STARTING AND OPERATING If Engine Fails to Start If the engine fails to start after you have followed the “NORMAL STARTING” or “EXTREME COLD WEATHER” procedures, it may be flooded. Push the accelerator pedal all the way to the floor and hold it there while cranking the engine. This should clear any excess fuel in case the engine is flooded. CAUTION! To prevent damage to the starter, do not crank the engine for more than 15 seconds at a time. Wait 10 to 15 seconds before trying again.
STARTING AND OPERATING 147 WARNING! WARNING! Remember to disconnect the cord before driving. Damage to the 110-115 volt AC electrical cord could cause electrocution. Unintended movement of a vehicle could injure those in and near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle you should shift the transmission into Park, remove the key from the ignition, and apply the park brake.
STARTING AND OPERATING CAUTION! WARNING! Damage to the transaxle may occur if the following precautions are not observed: • Shift into PARK only after the vehicle has come to a complete stop. • Shift into or out of REVERSE only after the vehicle has come to a complete stop and the engine is at idle speed. • Do not shift from REVERSE, PARK, or NEUTRAL into any forward gear when the engine is above idle speed. • Before shifting into any gear, make sure your foot is firmly on the brake pedal.
STARTING AND OPERATING Four Speed Automatic Transaxle The electronically controlled transaxle provides a precise shift schedule. The transaxle electronics are self calibrating; therefore, the first few shifts on a new vehicle may be somewhat abrupt. This is a normal condition, and precision shifts will develop within a few shift cycles. Reset Mode The transaxle is monitored electronically for abnormal conditions.
STARTING AND OPERATING WARNING! Your vehicle could move and injure you and others if it is not completely in P (Park). Check by trying to move the gearshift lever back and forth without depressing the shift button after you have set it in P. Make sure it is in Park before leaving the vehicle. WARNING! Never use the Park position as a substitute for the parking brake. Always apply the parking brake fully when parked to guard against vehicle movement and possible injury or damage.
STARTING AND OPERATING NOTE: Using the “3” range while operating the vehicle under heavy operating conditions will improve performance, fuel economy, and extend transaxle life by reducing excessive shifting and heat build up. Use the “3” range when descending steep grades to prevent brake system distress. 151 PARKING BRAKE When the parking brake is applied with the ignition on, the brake light in the instrument cluster will come on. NOTE: This light only shows that the parking brake is on.
STARTING AND OPERATING To release the parking brake, apply the brake pedal and pull up on the parking brake lever. Push the release button and lower the lever fully. When parking on a hill, it is important to set the parking brake before placing the gear selector in Park, otherwise the load on the transaxle locking mechanism may make it difficult to move the selector out of Park. As an added precaution, turn the front wheels toward the curb on a downhill grade and away from the curb on a uphill grade.
STARTING AND OPERATING 153 BRAKE SYSTEM Your vehicle is equipped with power assisted brakes as standard equipment. In the event power assist is lost for any reason (for example, repeated brake applications with the engine off), the brakes will still function. The effort required to brake the vehicle will be much greater than that required with the power system operating.
STARTING AND OPERATING During stops where ABS is activated, a vibration of the brake pedal may be felt and associated system noises may be heard. WARNING! Pumping of the brake pedal will diminish the effectiveness of Anti-lock brakes and may lead to an accident. Pumping makes the stopping distance longer. Just press firmly on your brake pedal when you need to slow down or stop.
STARTING AND OPERATING 155 POWER STEERING The power assisted steering system of your vehicle provides mechanical steering capability in the event power assist is lost. If for some reason the hydraulic pressure is interrupted, it will still be possible to steer your vehicle. Under these conditions you will observe a substantial increase in steering effort. TRACTION CONTROL — IF EQUIPPED The Traction Control System will improve acceleration and steering on slippery surfaces by reducing tire spin.
STARTING AND OPERATING • The system has been automatically deactivated to prevent damage to the brake system due to overheated brake temperatures. TIRE SAFETY INFORMATION Tire Markings NOTE: Extended heavy use of Traction Control may cause the system to deactivate and turn on the traction control light located in the instrument cluster. This is to prevent overheating of the brake system and is a normal condition. The system will remain disabled for about 4 minutes until the brakes have cooled.
STARTING AND OPERATING • European Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter ⬙P⬙ is absent from this tire size designation. Example: 215/65R15 96H • LT(Light Truck)-Metric tire sizing is based on U.S. design standards.
STARTING AND OPERATING EXAMPLE: R = Construction Code —⬙R⬙ means Radial Construction. —⬙D⬙ means Diagonal or Bias Construction. 15 = Rim Diameter in Inches (in) Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry. H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions.
STARTING AND OPERATING Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire however the date code may only be on one side. Tires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire. 159 Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the outboard side then you will find it on the inboard side of the tire.
STARTING AND OPERATING Tire Loading and Tire Pressure Tire and Loading Information Placard Tire Placard Location NOTE: The proper cold tire inflation pressure for passenger cars is listed on either the face of the driver’s door or the driver’s side “B” pillar. For vehicles other than passenger cars, the cold tire inflation pressures are listed on either the “B” pillar, the Certification Label or in the Tire Inflation Pressures brochure in the glove compartment.
STARTING AND OPERATING Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size and cold tire inflation pressures specified on the Tire and Loading Information placard and the Vehicle Loading section of this manual.
STARTING AND OPERATING 6. If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle. NOTE: The following table shows examples on how to calculate total load, cargo/luggage and towing capacities of your vehicle with varying seating configurations and number and size of occupants.
STARTING AND OPERATING 163 5
STARTING AND OPERATING WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES—GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle. Three primary areas are affected by improper tire pressure: 1.
STARTING AND OPERATING 165 2. Economy— Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Underinflation also increases tire rolling resistance and results in higher fuel consumption. 3. Ride Comfort and Vehicle Stability— Proper tire inflation contributes to a comfortable ride. Overinflation produces a jarring and uncomfortable ride.
STARTING AND OPERATING CAUTION! After inspecting or adjusting the tire pressure always reinstall the valve stem cap–if equipped. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressures specified on the placard are always “cold tire inflation pressure”. Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or driven less than 1mile (1 km) after a 3 hour period.
STARTING AND OPERATING WARNING! High speed driving with your vehicle under maximum load is dangerous. The added strain on your tires could cause them to fail. You could have a serious accident. Don’t drive a vehicle loaded to the maximum capacity at continuous speeds above 75 mph (120 km/h). 167 Cuts and punctures in radial tires are repairable only in the tread area because of sidewall flexing. Consult your authorized tire dealer for radial tire repairs.
STARTING AND OPERATING Do not install a wheel cover or attempt to mount a conventional tire on the compact spare wheel, since the wheel is designed specifically for the compact spare. tire affects vehicle handling. Since it is not the same tire, replace (or repair) the original tire and reinstall on vehicle at the first opportunity. Do not install more than one compact spare tire/wheel on the vehicle at any given time.
STARTING AND OPERATING 169 WARNING! Fast spinning tires can be dangerous. Forces generated by excessive wheel speeds may cause tire damage or failure. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 35 mph (55 km/h) when you are stuck. And don’t let anyone near a spinning wheel, no matter what the speed. Tread Wear Indicators Tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced.
STARTING AND OPERATING Replacement Tires The tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for wear and correct cold tire inflation pressure. The manufacturer strongly recommends that you use tires equivalent to the originals in size, quality and performance when replacement is needed (see the paragraph on tread wear indicators). Refer to the Tire and Loading Information placard for the size designation of your tire.
STARTING AND OPERATING CAUTION! Replacing original tires with tires of a different size may result in false speedometer and odometer readings. Alignment And Balance Poor suspension alignment may result in: 171 TIRE CHAINS Due to limited clearance, tire chains are not recommended. CAUTION! Damage to the vehicle may result if tire chains are used. 5 • Fast tire wear. • Uneven tire wear, such as feathering and one-sided wear. • Vehicle pull to right or left.
STARTING AND OPERATING Snow tires generally have lower speed ratings than what was originally equipped with your vehicle and should not be operated at sustained speeds over 75 mph (120 km/h). Tire Rotation Recommendations Tires on the front and rear axles of vehicles operate at different loads and perform different steering, driving and braking functions. For these reasons, they wear at unequal rates, and tend to develop irregular wear patterns.
STARTING AND OPERATING 173 AUTOSTICK — IF EQUIPPED Autostick is a driver-interactive transaxle that offers manual gear shifting capability to provide you with more control. Autostick allows you to maximize engine braking, eliminate undesirable upshifts and downshifts, and improve overall vehicle performance. This system can also provide you with more control during passing, city driving, cold slippery conditions, mountain driving, trailer towing, and many other situations.
STARTING AND OPERATING Autostick General Information • The transaxle will automatically upshift from first to second gear and from second to third gear when engine speed reaches about 6300 RPM. • Downshifts from third to second gear above 66 mph (106 km/h) and from second to first gear above 37 mph (60 km/h) will be ignored. • You can start out in first, second, or third gear. Shifting into fourth gear can occur only after vehicle speed reaches 15 mph (24 km/h).
STARTING AND OPERATING Poor quality gasoline can cause problems such as hard starting, stalling and hesitations. If you experience these symptoms, try another brand of “regular” gasoline before considering service for the vehicle. Over 40 automobile manufacturers around the world have issued and endorsed consistent gasoline specifications (the World Wide Fuel Charter, WWFC) to define fuel properties necessary to deliver enhanced emissions, engine performance, and durability for your vehicle.
STARTING AND OPERATING MMT in Gasoline MMT is a manganese containing metallic additive that is blended into some gasoline to increase the octane number. Gasolines blended with MMT offer no performance advantage beyond gasolines of the same octane number without MMT. Gasolines blended with MMT have shown to reduce spark plug life and reduce emission system performance in some vehicles. The manufacturer recommends using gasolines without MMT.
STARTING AND OPERATING • The use of fuel additives which are now being sold as octane enhancers are not recommended. Most of these products contain high concentrations of methanol. Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives are not the responsibility of the manufacturer. NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you. 177 • Do not inhale exhaust gases.
STARTING AND OPERATING ADDING FUEL Fuel Filler Cap (Gas Cap) The gas cap is behind the fuel filler door, on the driver’s side of the vehicle. If the gas cap is lost or damaged, be sure the replacement cap is for use with this vehicle. CAUTION! NOTE: Tighten the gas cap until you hear a “clicking” sound. This is an indication that the gas cap is properly tightened. The Malfunction Indicator Light will come on if the gas cap is not properly secured.
STARTING AND OPERATING WARNING! • Never have any smoking materials lit in or near the vehicle when the gas cap is removed or the tank filled. • Never add fuel to the vehicle when the engine is running. • A fire may result if gasoline is pumped into a portable container that is inside of a vehicle. You could be burned. Always place gas containers on the ground while filling. VEHICLE LOADING Vehicle Loading Capacities Front Seat Occupants . . . . . . . . . . . . . . . . . . . . . . . 2 Rear Seat Occupants .
STARTING AND OPERATING Towing Requirements • The maximum trailer load is 1,000 lbs (450 kg). • The maximum frontal area of the trailer cannot exceed 20 square feet (1.86 square meters). • If using a manual transaxle vehicle for trailer towing, all starts must be in FIRST gear to avoid excessive clutch slippage. • The trailer tongue load must be considered as part of the combined weight of occupants and cargo, and should never exceed the weight referenced on the Tire and Loading Information placard.
STARTING AND OPERATING NOTE: For vehicles equipped with Autostick. By using the Autostick modes, and selecting a specific gear range, frequent shifting can be avoided. The highest gear range should be selected that allows for adequate performance. For example, choose “4” if the desired speed can be maintained. Choose “3” or “2” if needed to maintain the desired speed. NOTE: Extended driving at high RPM should be avoided to prevent excess heat generation.
STARTING AND OPERATING ETHANOL FUEL (E-85) E-85 is a mixture of approximately 85% fuel ethanol and 15% unleaded gasoline. WARNING! Ethanol vapors are extremely flammable and could cause serious personal injury. Never have any smoking materials lit in or near the vehicle when removing the fuel filler tube cap (gas cap) or filling the tank. Do not use E-85 as a cleaning agent and never use it near an open flame.
STARTING AND OPERATING This symbol means that the oil has been certified by the American Petroleum Institute (API). We only recommend API Certified engine oils that meet the requirements of DaimlerChrysler’s Material Standard MS-9214. Use Mopar or an equivalent oil meeting the specification MS-9214. The manufacturer strongly recommends against the addition of any additives (other than leak detection dyes) to engine oil.
STARTING AND OPERATING Starting The characteristics of E-85 fuel make it unsuitable for use when ambient temperatures fall below 0°F (-18°C). In the range of 0°F to 32°F (-18°C to 0°C), you may experience an increase in the time it takes for your engine to start, and a deterioration in drivability (sags and/or hesitations) until the engine is fully warmed up. Cruising Range Because E-85 fuel contains less energy per gallon than gasoline, you will experience an increase in fuel consumption.
WHAT TO DO IN EMERGENCIES CONTENTS 䡵 Hazard Warning Flasher . . . . . . . . . . . . . . . . . 186 ▫ Traction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195 䡵 If Your Engine Overheats . . . . . . . . . . . . . . . . 186 䡵 Freeing A Stuck Vehicle . . . . . . . . . . . . . . . . . 196 䡵 Jacking And Tire Changing . . . . . . . . . . . . . . . 187 䡵 Towing A Disabled Vehicle . . . . . . . . . . . . . . . 196 ▫ Preparations For Jacking . . . . . . . . . . . . . . . .
WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER If it is necessary to leave the vehicle to go for service, the flasher system will continue to operate with the ignition key removed and the vehicle locked. NOTE: With extended use, the flasher may wear down your battery. IF YOUR ENGINE OVERHEATS In any of the following situations, you can reduce the potential for overheating by taking the appropriate action. • On the highways — Slow down.
WHAT TO DO IN EMERGENCIES CAUTION! Driving with a hot cooling system could damage your vehicle. If temperature gauge reads “H”, pull over and stop the vehicle. Idle the vehicle in Park with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the “H”, turn the engine off immediately, and call for service. WARNING! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant.
WHAT TO DO IN EMERGENCIES Preparations for Jacking Park the vehicle on a firm level surface, avoid ice or slippery areas, and set the parking brake. Place the gear selector in PARK. • Turn on the Hazard Warning Flasher, park vehicle on firm, level surface. • Put gear shift in park (automatic transmission) or reverse (manual transmission). • Set parking brake and turn off engine. • Passengers should not remain in the vehicle while the vehicle is being jacked.
WHAT TO DO IN EMERGENCIES 189 1. Block wheel diagonally opposite flat tire. 2. Remove the spare tire, scissors jack and lug wrench from stowage. 3. Before raising the vehicle, use lug wrench to carefully pry off wheel cover (if equipped with steel wheels) or center cap (if equipped with aluminum wheels). Loosen, but do not remove, the wheel nuts by turning them counterclockwise one turn while the wheel is still on the ground.
WHAT TO DO IN EMERGENCIES Jack Engagement Locations
WHAT TO DO IN EMERGENCIES 191 WARNING! WARNING! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. A loose tire or jack thrown forward in a collision or hard stop could endanger the occupants of the vehicle. Always stow the jack parts and the spare tire in the places provided. 6. Remove lug nuts and tire. 7. Mount spare tire. 8. Tighten all lug nuts on mounting studs. 9.
WHAT TO DO IN EMERGENCIES JUMP-STARTING PROCEDURES IF BATTERY IS LOW WARNING! • Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transaxle cannot be started this way. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle. If the vehicle has a discharged battery, booster cables may be used to obtain a start from another vehicle.
WHAT TO DO IN EMERGENCIES WARNING! Do not permit vehicles to touch each other as this could establish a ground connection and person injury could result. 193 5. Connect the other cable, first to the negative terminal of the booster battery and then to the jump start attachment of the vehicle with the discharged battery. Make sure you have a good contact on the engine. WARNING! Do not connect the cable to the negative post of the discharged battery.
WHAT TO DO IN EMERGENCIES 6. Start the engine in the vehicle that has the booster battery, let the engine idle a few minutes, then start the engine in the vehicle with the discharged battery. 7. When removing the jumper cables, reverse the above sequence exactly. Be careful of the moving belts and fan. WARNING! Any procedure other than above could result in: 1. Personal injury caused by electrolyte squirting out the battery vent; 2. Personal injury or property damage due to battery explosion; 3.
WHAT TO DO IN EMERGENCIES DRIVING ON SLIPPERY SURFACES Acceleration Rapid acceleration on snow covered, wet, or other slippery surfaces may cause the front wheels to pull erratically to the right or left. This phenomenon occurs when there is a difference in the surface traction under the front (driving) wheels, particularly with high output engines. WARNING! Rapid acceleration on slippery surfaces is dangerous. Unequal traction can cause sudden pulling of the front wheels.
WHAT TO DO IN EMERGENCIES FREEING A STUCK VEHICLE If your vehicle is equipped with Traction Control, turn the system off before attempting to “rock” the vehicle. If your vehicle becomes stuck in mud, sand or snow, it can often be moved by a rocking motion. Turn your steering wheel right and left to clear the area around the front wheels. Then shift back and forth between Reverse and First gear.
WHAT TO DO IN EMERGENCIES TOWING THIS VEHICLE BEHIND ANOTHER VEHICLE (Flat towing with all four wheels on the ground) Automatic Transaxle Your vehicle may be towed under the following conditions: The gear selector must be in NEUTRAL, the distance to be towed must not exceed 15 miles (25 km), and the towing speed must not exceed 25 mph (40 km/h). If the transaxle is not operative, or if the vehicle is to be towed more than 15 miles (25 km), the vehicle must be towed with the front wheels off the ground.
MAINTAINING YOUR VEHICLE CONTENTS 䡵 2.4L Engine . . . . . . . . . . . . . . . . . . . . . . . . . . 201 ▫ Power Steering — Fluid Check . . . . . . . . . . . . 215 䡵 2.7L Engine . . . . . . . . . . . . . . . . . . . . . . . . . . 202 ▫ Suspension Ball Joints . . . . . . . . . . . . . . . . . . 216 䡵 Onboard Diagnostic System — OBD II . . . . . . 203 ▫ Body Mechanism Lubrication . . . . . . . . . . . . . 216 䡵 Emissions Inspection And Maintenance Programs . . . . . . . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE ▫ Appearance Care And Protection From Corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . . 229 䡵 Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 234 ▫ Underhood Fuses (Power Distribution Center) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 234 ▫ Interior Fuses . . . . . . . . . . . . . . . . . . . . . . . . 234 䡵 Vehicle Storage . . . . . . . . . . . . . . . . . . . . . . . . 236 䡵 Replacement Light Bulbs . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 201 2.4L ENGINE 7 2.
MAINTAINING YOUR VEHICLE 2.7L ENGINE 2.
MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
MAINTAINING YOUR VEHICLE EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle’s emissions control system. Failure to pass could prevent vehicle registration. For states which have an I/M (Inspection and Maintenance) requirement, this check verifies the following: the MIL (Malfunction Indicator Lamp) is functioning and is not on when the engine is running, and that the OBD (On Board Diagnostic) system is ready for testing.
MAINTAINING YOUR VEHICLE b. The MIL will not flash at all and will remain fully illuminated until you turn off the ignition key or start the engine. This means that your vehicle’s OBD system is ready and you can proceed to the I/M station. If your OBD system is not ready, you should see your authorized dealer or repair facility.
MAINTAINING YOUR VEHICLE WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the proper equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic. MAINTENANCE PROCEDURES The pages that follow contain the required maintenance services determined by the engineers who designed your vehicle.
MAINTAINING YOUR VEHICLE 207 Change Engine Oil Road conditions and your kind of driving affects the interval at which your oil should be changed. Check the following list to decide if any apply to you. • Day and night temperatures are below 32° F (0° C) • Stop and Go driving • Extensive engine idling. • Driving in dusty conditions • Short trips of less than 10 miles (16.2 km) Engine Oil Dipstick CAUTION! Overfilling or underfilling will cause aeration or loss of oil pressure.
MAINTAINING YOUR VEHICLE • If equipped for and operating with E-85 (ethanol) fuel. NOTE: If ANY of these apply to you then change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first and follow schedule “B” of the ⬙Maintenance Schedules⬙ section of this manual. If none of these apply to you, then change your engine oil at every interval shown on schedule ⬙A⬙ of the ⬙Maintenance Schedules⬙ section of this manual.
MAINTAINING YOUR VEHICLE Engine Oil Viscosity (SAE Grade) 209 Flexible Fuel Engine Oil If you operate the vehicle on E-85 fuel either full or part-time, use only Mopar Flexible Fuel 5W-30 engine oil or an equivalent that meets the manufacturers Standard MS-9214. Equivalent commercial Flexible Fuel engine oils may be labeled as Flexible Fuel (FFV) or Alternate Fuel (AFV). These engine oils may be satisfactory if they meet the manufacturer’s standard.
MAINTAINING YOUR VEHICLE Materials Added To Engine Oils The manufacturer strongly recommends against the addition of any additives (other than leak detection dyes) to engine oil. Engine oil is an engineered product and it’s performance may be impaired by supplemental additives. Disposing of Used Engine Oil and Oil Filters Care should be taken in disposing of used engine oil from your vehicle. Used oil, indiscriminately discarded, can present a problem to the environment.
MAINTAINING YOUR VEHICLE Engine Air Cleaner Filter Under normal driving conditions, replace the air filter at the intervals shown on Schedule “A”. If, however, you drive the vehicle frequently under dusty or severe conditions, the filter element should be inspected periodically and replaced if necessary at the intervals shown on Schedule “B”. WARNING! The air cleaner can provide a measure of protection in the case of engine backfire.
MAINTAINING YOUR VEHICLE WARNING! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your exhaust system. Do not park or operate your vehicle in areas where your exhaust system can contact anything that can burn. In unusual situations involving grossly malfunctioning engine operation, a scorching odor may suggest severe and abnormal catalyst overheating.
MAINTAINING YOUR VEHICLE NOTE: The battery is stored in a compartment behind the left front fender and is accessible without removing the tire and wheel. Remote battery terminals are located in the engine compartment for jump starting. Battery Location To access the battery, turn the steering wheel fully to the right and remove the inner fender shield. 213 WARNING! Battery posts, terminals and related accessories contain lead and lead compounds. Wash hands after handling.
MAINTAINING YOUR VEHICLE CAUTION! It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked positive (+) and negative (-) and identified on the battery case. Cable clamps should be tight on the terminal posts and free of corrosion. Apply grease to posts and clamps after tightening.
MAINTAINING YOUR VEHICLE Refrigerant Recovery and Recycling R-134a Air Conditioning Refrigerant is a hydrofluorocarbon (HFC) that is endorsed by the Environmental Protection Agency and is an ozone-saving product. However, the manufacturer recommends that air conditioning service be performed by dealers or other service facilities using recovery and recycling equipment.
MAINTAINING YOUR VEHICLE Fluid level should be maintained at the proper level indicated on the side of the reservoir. If necessary, add fluid to restore the proper indicated level. With a clean cloth, wipe any spilled fluid from all surfaces. Refer to Recommended Fluids, Lubricants, and Genuine Parts for correct fluid type. Suspension Ball Joints There are two upper front and rear suspension ball joints. Inspect these ball joints whenever under vehicle service is done.
MAINTAINING YOUR VEHICLE If you use a lubricant that cannot be dispensed directly into the lock cylinder, apply a small amount of the lubricant to the key. Insert the key into the lock cylinder, then proceed as described above, to distribute the lubricant within the lock cylinder. Pay attention to trunk hinges, especially during cold weather, to ensure ease of trunk operation.
MAINTAINING YOUR VEHICLE Windshield Wiper Blade Replacement • Lift the wiper arm away from the glass. • Push the release tab and slide the wiper blade assembly away from the wiper arm. Gently place the wiper arm on the windshield. • Install the new blade assembly onto the wiper arm tip until it locks in place. Windshield Washers The fluid reservoir in the engine compartment should be checked for fluid level at regular intervals.
MAINTAINING YOUR VEHICLE Exhaust System The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. If you notice a change in the sound of the exhaust system; or if exhaust fumes can be detected inside the vehicle; or when the underside or rear of the vehicle is damaged; have a competent mechanic inspect the complete exhaust system and adjacent body areas for broken, damaged, deteriorated, or mispositioned parts.
MAINTAINING YOUR VEHICLE applicable). If coolant is dirty or rusty in appearance, the system should be drained, flushed and refilled with fresh coolant. Cooling System Inspection WARNING! • When working near the radiator cooling fan, disconnect the fan motor lead or turn the ignition key to the OFF position. The fan is controlled by both the temperature of the engine cooling system and the pressure in the air conditioning system and can start at any time the ignition key is in the ON position.
MAINTAINING YOUR VEHICLE Do not remove the cap when the cooling system is hot. Cooling System — Drain, Flush and Refill At the intervals shown on the Maintenance Schedules, the system should be drained, flushed and refilled. The first change should not be required until 5 years or 100,000 miles (160,000 km), whichever comes first. The coolant should be flushed and changed every two years or 36,000 miles (57,600 km) thereafter.
MAINTAINING YOUR VEHICLE Adding Coolant When adding coolant, or refilling the system, a minimum solution of 50% recommended HOAT ethylene glycol engine coolant (antifreeze) and distilled water should be used. Use higher concentrations (not to exceed 70%) if temperatures below ⫺34°F (⫺37°C) are anticipated. Please note that it is the owner’s responsibility to maintain the proper level of protection against freezing according to the temperatures occurring in the area where the vehicle is operated.
MAINTAINING YOUR VEHICLE Disposal Of Used Engine Coolant Used ethylene glycol based engine coolant is a regulated substance requiring proper disposal. Check with your local authorities to determine the disposal rules for your community. Do not store ethylene glycol based engine coolant in open containers or allow it to remain in puddles on the ground. Prevent ingestion by animals or children. If ingested by a child, contact a physician immediately.
MAINTAINING YOUR VEHICLE • Check coolant freeze point in the system. • If frequent coolant additions are required, or if the level in the bottle does not drop when the engine cools, the cooling system should be pressure tested for leaks. • Maintain coolant concentration at 50% HOAT ethylene glycol engine coolant (minimum) and distilled water for proper corrosion protection of your engine which contains aluminum components.
MAINTAINING YOUR VEHICLE WARNING! Riding the brakes can lead to brake failure and possibly an accident. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage. You may not have your full braking capacity in an emergency. Brake and Power Steering System Hoses When servicing the vehicle for scheduled maintenance, inspect surface of hoses and nylon tubing for evidence of heat and mechanical damage.
MAINTAINING YOUR VEHICLE Master Cylinder The fluid level in the master cylinder should be checked when performing under hood services, or immediately if the brake system warning lamp shows system failure. Use only manufacturer’s recommended brake fluid, refer to Recommended Fluids, Lubricants and Genuine Parts for correct fluid type.
MAINTAINING YOUR VEHICLE Do not allow petroleum base fluid to contaminate the brake fluid as seal damage will result! Fuel System Hoses Electronic Fuel Injection high pressure fuel systems are designed with hoses and clamps which have unique material characteristics to provide adequate sealing and resist attack by deteriorated gasoline. You are urged to use only manufacturer specified hoses and clamps, or their equivalent in material and specification, in any fuel system servicing.
MAINTAINING YOUR VEHICLE Procedure For Checking Fluid Level The fluid level in the automatic transaxle should be checked whenever the vehicle is serviced. Operation with an improper fluid level will greatly reduce the life of the transaxle and of the fluid. To properly check the automatic transaxle fluid level, the following procedure must be used: • The vehicle must be on level ground. • The engine should be running at curb idle speed for a minimum of 60 seconds. • Fully apply parking brake.
MAINTAINING YOUR VEHICLE • Police, taxi, limousine, commercial type operation, or trailer towing where the vehicle is driven regularly for more than 45 minutes of continuous operation. NOTE: Refer to Section 8 of this manual for maintenance schedules. If the transaxle is disassembled for any reason, the fluid and filter should be changed. Special Additives The manufacturer recommends against the addition of any fluid additives to the transaxle.
MAINTAINING YOUR VEHICLE What Causes Corrosion? Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle. • Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish. The most common causes are: CAUTION! • Road salt, dirt and moisture accumulation. • Stone and gravel impact. • Insects, tree sap and tar.
MAINTAINING YOUR VEHICLE 231 • Use Mopar touch up paint on scratches or chips as soon as possible. Your dealer has touch up paint to match the color of your vehicle. Never use cleaners that contain acid, oven cleaners or any abrasive metal cleaner as they will cause permanent staining and/or corrosion. • If your vehicle is damaged due to an accident or similar cause which destroys the paint and protective coating have your vehicle repaired as soon as possible.
MAINTAINING YOUR VEHICLE You should not increase the gloss level, especially on top of the instrument panel top surface. Higher gloss levels will increase the reflectivity in the windshield that could decrease visibility under bright light driving conditions. WARNING! Do not use volatile solvents for cleaning purposes. Many are potentially flammable, and if used in closed areas they may cause respiratory harm.
MAINTAINING YOUR VEHICLE 233 Never use an abrasive type cleaner. Use caution when cleaning inside rear windows equipped with electric defrosters. Do not use scrapers or other sharp instruments which may scratch the elements. Cleaning Plastic Instrument Cluster Lenses The lenses in front of the instruments in this vehicle are molded in clear plastic. When cleaning the lenses, care must be taken to avoid scratching the plastic.
MAINTAINING YOUR VEHICLE FUSES Underhood Fuses (Power Distribution Center) A Power Distribution Center is located in the engine compartment; near the air cleaner. This information applies to vehicles built without the fuse and relay numbering embossed on the Power Distribution Center Top Cover. Interior Fuses Fuse Panel Cover The fuse access panel is behind the end cover at the left side of the instrument panel. To remove the panel, pull it out, as shown.
MAINTAINING YOUR VEHICLE The identity of each fuse is indicated on the backside of the cover.
MAINTAINING YOUR VEHICLE Cavity 15 Fuse 10 Amp Red 16 10 Amp Red 10 Amp 20 Amp C/BRKR 30 Amp C/BRKR 17 18 19 Circuit Turn Signal and Hazard Flashers, Wiper Switch, Seat Belt Control Module, Wiper Relays, Rear Window Defroster Relay Airbag Control Module Airbag Control Module Power Seat Switch, Remote Trunk Release Power Windows CAUTION! When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating.
MAINTAINING YOUR VEHICLE REPLACEMENT LIGHT BULBS LIGHT BULBS — Interior Bulb Number Instrument Cluster . . . . . . . . . . . . . . . . . . . . . PC 194 ABS Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . PC 161 Fog Light Indicator. . . . . . . . . . . . . . . . . . . . . PC 161 Dome Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . 578 Front Reading/Map Lights. . . . . . . . . . . . . . . . . . 906 Trunk Light . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 2. Remove the push-in fasteners by prying under the head of the fasteners with a flat bladed tool. 3. Gently pry the headlight assembly away from the fender as shown in the picture. This will free the ball stud from its retainer in the fender. Pull the headlight assembly away from the vehicle.
MAINTAINING YOUR VEHICLE 4. Turn the retaining ring counterclockwise and remove the bulb and socket assembly. 239 6. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol. 7. Reinsert the bulb and socket assembly and turn the retaining ring clockwise to secure the bulb. 8. Reinstall the headlight assembly. Park, Turn Signal, Sidemarker Bulb Replacement 1. Open the hood and remove the two headlight assembly mounting screws.
MAINTAINING YOUR VEHICLE 2. Turn the bulb socket counterclockwise and remove the bulb and socket assembly. 3. Pull the bulb out of the socket, replace the bulb, and reinstall the bulb and socket to the headlight assembly. Reinstall the headlight assembly. Fog Light Bulb Replacement 1. Remove the screws securing the light assembly to the front fascia. 2. Pull the light assembly away from the vehicle to expose the bulb and socket assembly. 3.
MAINTAINING YOUR VEHICLE 4. Turn the bulb and socket assembly counterclockwise to remove it from the housing. 241 Center Stoplight Bulb Replacement 1. Open the trunk. Turn the bulb socket counterclockwise to remove it from the housing. 7 5. Install the new bulb and socket assembly, reattach the wiring connector, and reinstall the fog light assembly. 2. Pull the bulb out of the socket, replace the bulb and reinstall the bulb and socket assembly.
MAINTAINING YOUR VEHICLE Rear Light Bulb Replacement 1. Open the trunk and pull the trunk liner away to expose the wiring connector and light housing plastic retainers. 3. Turn the bulb socket counterclockwise to remove it from the housing. Remove and replace the bulb then reinstall the bulb and socket assembly. 4. Reinstall the light housing and reconnect the wiring connector. Push the trunk liner back into place. License Plate Bulb Replacement 1.
MAINTAINING YOUR VEHICLE Headlight Aiming The headlights on your new vehicle were aimed at the factory. The factory setting was made at a no load setting. A great increase in weight will change the aiming and it may be necessary to readjust the headlights if carrying an excessive amount of weight in the trunk, rear seats or pulling a trailer. To readjust the headlights first mark the position of the headlights on a wall prior to loading the vehicle.
MAINTAINING YOUR VEHICLE RECOMMENDED FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant Engine Oil Spark Plugs Oil Filter (2.4L Engine) Oil Filter (2.7L Engine) Fuel Selection Fluid, Lubricant, or Genuine Part Mopar威 Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) Use API Certified engine oil. SAE 5W-20 and SAE 5W-30 are recommended. Refer to the engine oil fill cap for the correct SAE grade meeting DaimlerChrysler Material Standard MS-6395.
MAINTENANCE SCHEDULES CONTENTS M A I N T E N A N C E 䡵 Emission Control System Maintenance . . . . . . 246 ▫ Schedule “B” . . . . . . . . . . . . . . . . . . . . . . . . 250 䡵 Partial Zero Emissions Vehicle (PZEV) For 2.4L — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 246 ▫ Schedule “A” . . . . . . . . . . . . . . . . . . . . . . . . 260 C 䡵 Maintenance Schedules . . . . . . . . . . . . . . . . . .
M A I N T E N A N C E 246 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
MAINTENANCE SCHEDULES NOTE: There are specific instructions regarding when to change the ignition cables and spark plugs with the PZEV package in this section. This applies to both maintenance schedule A and B and will be marked with an ** or ***. MAINTENANCE SCHEDULES There are two maintenance schedules that show the required service for your vehicle. First is Schedule “B”. It is for vehicles that are operated under the conditions that are listed below and at the beginning of the schedule.
M A I N T E N A N C E S C H E D U L E S 8 248 MAINTENANCE SCHEDULES Use the schedule that best describes your driving conditions. Where time and mileage are listed, follow the interval that occurs first. • Check the windshield washer solvent and add if required. NOTE: Under no circumstances should oil change intervals exceed 6 months or 6,000 miles, whichever comes first. • Check tire pressure and look for unusual wear or damage.
MAINTENANCE SCHEDULES At Each Oil Change • Change the engine oil filter. • Inspect the exhaust system. • Inspect the brake linings, hoses and calipers. • Inspect the CV joints and front and rear suspension components. • Check the automatic transmission fluid level. 249 M A I N T • Check the coolant level, hoses, and clamps. E NOTE: In 2.7L Engines equipped with Flex Fuel Engine N A (FFV), change engine oil every 5 months or 5,000 miles, N whichever comes first.
M A I N T E N A N C E S C H E D U L E S 8 250 SCHEDULE “B” SCHEDULE “B” Follow schedule “B” if you usually operate your vehicle under one or more of the following conditions. Change the automatic transmission fluid and filter every 60,000 miles (96 000 km) if the vehicle is usually operated under one or more of the conditions marked with an 〫. • Taxi, police or delivery service (commercial services).〫 • Day or night temperatures are below 32° F (0° C).
SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Inspect the air cleaner filter and replace if necessary.* Inspect the front and rear brake pads, linings, rotors, rear drums and shoes. Rotate the tires.
M 252 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter, if not A replaced at 3 months. N C Inspect the air cleaner filter and replace if reE quired.* S C H E D U L E S 8 Replace the air cleaner filter. Inspect and check tension for power steering belt (2.4 Liter Engine). Adjust or replace if required. Inspect the front and rear brake pads, linings, rotors, rear drums and shoes. Check and replace, if necessary, the PCV valve. * Replace the spark plugs on 2.4 liter engine.
SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Inspect the air cleaner filter and replace if necessary.* Inspect the front and rear brake pads, linings, rotors, rear drums and shoes. Rotate the tires.
M 254 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter, if not reA placed at 3 months. N C Inspect the air cleaner filter and replace if necesE sary.* S C H E D U L E S 8 Replace the air cleaner filter. Inspect and check tension for power steering belt (2.4 Liter Engine). Adjust or replace if required. Inspect the front and rear brake pads, linings, rotors, rear drums and shoes. Replace the ignition cables on 2.4 liter engine.
SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Inspect the air cleaner filter and replace if necessary.* Replace the air cleaner filter. Inspect and check tension for power steering belt (2.4 Liter Engine). Adjust or replace if required. Replace the engine timing belt on 2.4 liter engine. * Inspect the front and rear brake pads, linings, rotors, rear drums and shoes. Replace the spark plugs on 2.4 liter engine.
M 256 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter, if not A replaced at 3 months. N C Inspect the air cleaner filter and replace if E necessary.* S C H E D U L E S 8 Replace the spark plugs on the 2.4 liter engine. *** Replace the ignition cables on the 2.4 liter engine. *** Inspect the front and rear brake pads, linings, rotors, rear drums and shoes. Replace the spark plugs on the 2.7 liter engine. Check and retension accessory drive belts on 2.7 liter engine.
SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Inspect the air cleaner filter and replace if necessary.* Replace the air cleaner filter. Replace the spark plugs on the 2.4 liter engine. ** Replace the ignition cables on the 2.4 liter engine. ** Inspect the front and rear brake pads, linings, rotors, rear drums and shoes. Replace the accessory drive belts on 2.7 liter engine. Check and replace, if necessary, the PCV valve.
M 258 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter, if not A replaced at 3 months. N C Inspect the air cleaner filter and replace if E necessary.* S C H E D U L E S 8 Inspect and check tension for power steering belt (2.4 Liter Engine). Adjust or replace if required. Inspect the front and rear brake pads, linings, rotors, rear drums and shoes. Rotate the tires.
SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Inspect the air cleaner filter and replace if necessary.* Replace the air cleaner filter. Replace the spark plugs on the 2.4 liter engine. ** Inspect the front and rear brake pads, linings, rotors, rear drums and shoes. Check and replace, if necessary, the PCV valve. *‡ Rotate the tires.
M 260 SCHEDULE “A” A I SCHEDULE “A” N T Miles E N (Kilometers) A [Months] N C Change engine oil and engine oil filter. E Inspect the air cleaner filter and replace if S C H E D U L E S 8 necessary.* Replace the air cleaner filter. Replace the spark plugs on 2.4 liter engine. ** Inspect the front and rear brake pads, linings, rotors, rear drums and shoes. Rotate the tires.
SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Inspect the air cleaner filter and replace if required.* Replace the air cleaner filter. Inspect and check tension for power steering belt (2.4 Liter Engine). Adjust or replace if required. Inspect the front and rear brake pads, linings, rotors, rear drums and shoes. Replace the spark plugs on 2.4 liter engine. ** Flush and replace the engine coolant at 60 months, if not done at 100,000 miles.
M 262 SCHEDULE “A” A I 78,000 84,000 90,000 96,000 100,000 102,000 105,000 N Miles T (Kilometers) (125 000) (134 000) (144 000) (154 000) (160 000) (163 000) (168 000) E [78] [84] [90] [96] [102] [105] N [Months] A Change engine oil and engine oil filter. X X X X X N X X X X C Inspect the air cleaner filter and replace E if required.* S C H E D U L E S 8 Replace the air cleaner filter. Inspect the front and rear brake pads, linings, rotors, rear drums and shoes. Replace the spark plugs on 2.
SCHEDULE “A” Miles (Kilometers) [Months] Replace the spark plugs on 2.4 liter engine. *** Flush and replace the engine coolant, if not replaced at 60 months. Rotate the tires.
M 264 SCHEDULE “A” A I N Miles T (Kilometers) E N [Months] A Change engine oil and engine oil filter. N C Inspect the air cleaner filter and replace if E required.* S C H E D U L E S 8 Replace the air cleaner filter. Inspect the front and rear brake pads, linings, rotors, rear drums and shoes. Replace the spark plugs on 2.4 liter engine. ** Check and replace, if necessary, the PCV valve. *‡ Replace the engine timing belt on 2.4 liter engine.** Replace the accessory drive belts in 2.7 liter engine.
SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Inspect the air cleaner filter and replace if required.* Replace the air cleaner filter. Inspect the front and rear brake pads, linings, rotors, rear drums and shoes. Check and replace, if necessary, the PCV valve. *‡ Replace the engine timing belt on 2.4 liter engine.*** Replace the spark plugs on 2.4 liter engine. ** Rotate the tires.
M 266 SCHEDULE “A” A I WARNING! N T E You can be badly injured working on or around a N motor vehicle. Do only that service work for which A you have the knowledge and the right equipment. If N C you have any doubt about your ability to perform a E S C H E D U L E S 8 service job, take your vehicle to a competent mechanic.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS 䡵 Suggestions For Obtaining Service For Your Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 268 ▫ Prepare For The Appointment . . . . . . . . . . . . 268 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . . . 268 䡵 Reporting Safety Defects . . . . . . . . . . . . . . . . . 272 ▫ In Canada . . . . . . . . . . . . . . . . . . . . . . . . . . 272 䡵 Publication Order Forms . . . . . . . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty, discuss additional charges with the service manager. Keep a maintenance log of your vehicle’s service history. This can often provide a clue to the current problem.
IF YOU NEED CONSUMER ASSISTANCE • If for some reason you are still not satisfied, talk to the general manager or owner of the dealership. They want to know if you need assistance. • If your dealership is unable to resolve the concern, you may contact the Manufacturer’s Customer Center.
IF YOU NEED CONSUMER ASSISTANCE Service Contract You may have purchased a service contract for your vehicle to help protect you from the high cost of unexpected repairs after your manufacturer’s new vehicle limited warranty expires. The manufacturer stands behind only the manufacturer’s Service Contracts. If you purchased a manufacturer’s Service Contract, you will receive Plan Provisions and an Owner Identification Card in the mail within three weeks of your vehicle delivery date.
IF YOU NEED CONSUMER ASSISTANCE 271 9 U.S.
IF YOU NEED CONSUMER ASSISTANCE MOPAR姞 PARTS Mopar威 fluids, lubricants, parts, and accessories are available from your dealer. They will help you keep your vehicle operating at its best. REPORTING SAFETY DEFECTS In the 50 United States and Washington D.C.: If you believe that your vehicle has a defect which could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying the manufacturer.
IF YOU NEED CONSUMER ASSISTANCE • Service Manuals. These comprehensive service manuals provide the information that students and professional technicians need in diagnosing/troubleshooting, problem solving, maintaining, servicing and repairing DaimlerChrysler Corporation vehicles. A complete working knowledge of the vehicle, system and/or components is written in straightforward language with illustrations, diagrams and charts. • Diagnostic Procedure Manuals.
IF YOU NEED CONSUMER ASSISTANCE DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES The following describes the tire grading categories established by the National highway Traffic Safety Administration. The specific grade rating assigned by the tire’s manufacturer in each category is shown on the sidewall of the tires on your car.
IF YOU NEED CONSUMER ASSISTANCE Temperature Grades The temperature grades are A (highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
INDEX 10
INDEX About Your Brakes . . . . . . . . . . . . . . . . . . . . . . 153 ABS (Anti-Lock Brake) System . . . . . . . . . . . . . 153 Adding Engine Coolant (Antifreeze) . . . . . . . . . 222 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . 178 Adding Washer Fluid . . . . . . . . . . . . . . . . . . . . 218 Additives, Fuel . . . . . . . . . . . . . . . . . . . . . . . . 176 Aiming Headlights . . . . . . . . . . . . . . . . . . . . . . 243 Air Cleaner, Engine (Engine Air Cleaner Filter) .
INDEX Special Additives . . . . . . . . . . . . . . . . . . . . . 229 Autostick . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173 Auxiliary Power Outlet . . . . . . . . . . . . . . . . . . . 81 Ball Joints . . . . . . . . . . . . . . . . . . . . . . . . . . . . 216 Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 212 Emergency Starting . . . . . . . . . . . . . . . . . . . . 192 Gas Caution . . . . . . . . . . . . . . . . . . . . . . 194,213 Heater . . . . . . . . . . . . .
INDEX Charging System Light . . . . . . . . . . . . . . . . . . . 91 Chart, Tire Sizing . . . . . . . . . . . . . . . . . . . . . . . 157 Check Engine Light (Malfunction Indicator Light) . . . . . . . . . . . . . . 204 Checking Your Vehicle For Safety . . . . . . . . . . . . 48 Child Restraint . . . . . . . . . . . . . . . . . . . 40,43,45,46 Child Restraint Tether Anchors . . . . . . . . . . . . . 45 Child Safety Locks . . . . . . . . . . . . . . . . . . . . . . . 18 Cigar Lighter . . . . . . . . . .
INDEX Daytime Brightness, Interior Lights . . . . . . . . . . 65 Daytime Running Lights . . . . . . . . . . . . . . . . . . 67 Dealer Service . . . . . . . . . . . . . . . . . . . . . . . . . 205 Defroster, Rear Window . . . . . . . . . . . . . . . . . . 136 Defroster, Windshield . . . . . . . . . . . . . . . 49,130,135 Diagnostic System, Onboard . . . . . . . . . . . . . . . 203 Dimmer Control . . . . . . . . . . . . . . . . . . . . . . . . 64 Dimmer Switch, Headlight . . . . . . . . . . . . . . . . .
INDEX Oil Synthetic . . . . . . . . . . . . . . . . . . . . . . . . . 209 Overheating . . . . . . . . . . . . . . . . . . . . . . . . . 186 Partial Zero Emissions Vehicle for 2.4 Liter . . 246 Timing Belt . . . . . . . . . . . . . . . . . . . . . . . . . . 212 Engine Oil Viscosity . . . . . . . . . . . . . . . . . . . . . 243 Entry System, Illuminated . . . . . . . . . . . . . . . . . 15 Exhaust Gas Caution . . . . . . . . . . . . . . . 48,177,219 Exhaust System . . . . . . . . . . . . . . . . . . . .
INDEX Clean Air . . . . . . . . . . . . . . . . . . . . . . . . . . . 175 Ethanol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182 Filler Cap . . . . . . . . . . . . . . . . . . . . . . . . . . . 178 Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 211 Gasoline . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174 Gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 Hoses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 227 Light . . . . . . .
INDEX Hood Prop . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 Hood Release . . . . . . . . . . . . . . . . . . . . . . . . . . 63 Hoses . . . . . . . . . . . . . . . . . . . . . . . . . . . . 224,227 Ignition Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Illuminated Entry . . . . . . . . . . . . . . . . . . . . . . . 15 Immobilizer . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Bulb Replacement . . . . . . . . . . . . . . . . . . . . . 237 Check Engine . . . . . . . . . . . . . . . . . . . . . . . . . 91 Daytime Running . . . . . . . . . . . . . . . . . . . . . . 67 Dimmer Switch, Headlight . . . . . . . . . . . . . 66,68 Engine Temperature Warning . . . . . . . . . . . . . 92 Exterior Check . . . . . . . . . . . . . . . . . . . . . . . . 49 Fog . . . . . . . . . . . . . . . . . . . . . . . . . . . 67,92,240 Front Replacement . . . . . . . . . . . . . . . . . . . .
INDEX Lubrication, Body . . . . . . . . . . . . . . . . . . . . . . . 216 Luggage/Cargo Capacity . . . . . . . . . . . . . . . . . 179 Lumbar Support . . . . . . . . . . . . . . . . . . . . . . . . 60 Maintenance Free Battery . . . . . . . . . . . . . . . . . 212 Maintenance Procedures . . . . . . . . . . . . . . . . . . 206 Maintenance Schedule . . . . . . . . . . . . . . . . . . . 247 Light Duty Schedule ⬙B⬙ . . . . . . . . . . . . . . . . 250 Schedule ⬙A⬙ . . . . . . . . . . . . . . . . . . . . . .
INDEX Overdrive . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150 Overheating, Engine . . . . . . . . . . . . . . . . . . . . . 186 Owner’s Manual . . . . . . . . . . . . . . . . . . . . . . 4,272 Paint Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . 229 Paint Damage . . . . . . . . . . . . . . . . . . . . . . . . . 229 Panic Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Parking Brake . . . . . . . . . . . . . . . . . . . . . . . . . 151 Parking On Hill . . . . . . .
INDEX Remote Sound System Controls . . . . . . . . . . . . 122 Remote Trunk Release . . . . . . . . . . . . . . . . . . . . 24 Replacement Tires . . . . . . . . . . . . . . . . . . . . . . 170 Reporting Safety Defects . . . . . . . . . . . . . . . . . 272 Restraint, Head . . . . . . . . . . . . . . . . . . . . . . . . . 61 Restraints, Occupant . . . . . . . . . . . . . . . . . . . . . 26 Rocking Vehicle When Stuck . . . . . . . . . . . . . . 196 Rotation, Tires . . . . . . . . . . . . . . . . . . . .
INDEX Side Airbag . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Side Window Demisters . . . . . . . . . . . . . . . 131,136 Signals, Turn . . . . . . . . . . . . . . . . . . . . . . . . . . . 91 Slippery Surfaces, Driving On . . . . . . . . . . . . . 195 Snow Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171 Spare Tire . . . . . . . . . . . . . . . . . . . . . . . . . 167,168 Spark Plugs . . . . . . . . . . . . . . . . . . . . . . . . . . . 210 Speed Control . . . . . . . . . .
INDEX High Speed . . . . . . . . . . . . . . . . . . . . . . . . . 166 Inflation Pressures . . . . . . . . . . . . . . . . . . . . 165 Jacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188 Load Capacity . . . . . . . . . . . . . . . . . . . . 160,161 Quality Grading . . . . . . . . . . . . . . . . . . . . . . 274 Radial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167 Replacement . . . . . . . . . . . . . . . . . . . . . . . . . 170 Rotation . . . . . . . . . . . . . . . .
INDEX Unleaded Gasoline . . . . . . . . . . . . . . . . . . . . . . 174 Vacuum/Vapor Harnesses . . . . . . . . . . . . . . . . 224 Vanity Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . 58 Vehicle Identification Number . . . . . . . . . . . . . . . 6 Vehicle Loading . . . . . . . . . . . . . . . . . . . . . 161,179 Vehicle Modifications/Alterations . . . . . . . . . . . . 7 Vehicle Storage . . . . . . . . . . . . . . . . . . . . . . . . . 236 Vehicle Theft Alarm . . . . . . . . . . . . . . . .
