TABLE OF CONTENTS SECTION PAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 1 1 INTRODUCTION 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4 UNDERSTANDING YOUR INSTRUMENT PANEL 5 STARTING AND OPERATING 6 WHAT TO DO IN EMERGENCIES 7 MAINTAINING YOUR VEHICLE 8 MAINTENANCE SCHEDULES 9 IF YOU NEED CONSUMER ASSISTANCE 10 INDEX . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION CONTENTS m Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 m Vehicle Identification Number . . . . . . . . . . . . . . . 6 m How To Use This Manual . . . . . . . . . . . . . . . . . . 4 m Vehicle Modifications / Alterations . . . . . . . . . . . 7 m Warnings And Cautions . . . . . . . . . . . . . . . . . . .
INTRODUCTION INTRODUCTION This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a Warranty Information Booklet and various customer oriented documents. You are urged to read these publications carefully. Following the instructions and recommendations in this manual will help assure safe and enjoyable operation of your vehicle.
INTRODUCTION 5 1
INTRODUCTION WARNINGS AND CAUTIONS This manual contains WARNINGS against operating procedures which could result in an accident or bodily injury. It also contains CAUTIONS against procedures which could result in damage to your vehicle. If you do not read this entire manual you may miss important information. Observe all Warnings and Cautions.
INTRODUCTION 7 VEHICLE MODIFICATIONS / ALTERATIONS 1 WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS m A Word About Your Keys . . . . . . . . . . . . . . . . . .11 ▫ Manual Door Locks . . . . . . . . . . . . . . . . . . . . .16 ▫ Ignition Key Removal . . . . . . . . . . . . . . . . . . .11 ▫ Power Door Locks . . . . . . . . . . . . . . . . . . . . .17 ▫ Key-In-Ignition Reminder . . . . . . . . . . . . . . . .12 ▫ Child Protection Door Lock . . . . . . . . . . . . . . .18 m Sentry Key . . . . . . . . . . . . . . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE m Vehicle Theft Alarm . . . . . . . . . . . . . . . . . . . . . .24 ▫ Seat Belt Extender . . . . . . . . . . . . . . . . . . . . . .42 m Liftgate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 ▫ Driver And Front Passenger Supplemental Restraint System - Airbag . . . . . . . . . . . . . . . .43 ▫ Power Liftgate — If Equipped . . . . . . . . . . . . .27 m Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 ▫ Power Windows .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS You can insert the double sided keys into the locks with either side up. 11 be used to order duplicate keys from your dealer. Ask your dealer for these numbers and keep them in a safe place. Ignition Key Removal The shift lever must be in PARK. Turn the key to the LOCK position, then remove the key. The dealer that sold you your new vehicle has the key code numbers for your vehicle locks.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: The power window switches, radio, power sunroof, and power outlets will remain active for up to 45 seconds after the ignition switch has been turned off. Opening either front door will cancel this feature. CAUTION! An unlocked car is an invitation to thieves. Always remove key from the ignition and lock all doors when leaving the vehicle unattended. WARNING! Leaving children in a vehicle unattended is dangerous for a number of reasons.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 The Sentry Key Immobilizer System does not need to be armed or activated. Operation of the system is automatic regardless of whether or not the vehicle is locked or unlocked. During normal operation, the Theft Alarm/ Immobilizer Light will come on for three (3) seconds immediately after the ignition switch is turned on for a bulb check. Afterwards, if the bulb remains on, this indicates a problem with the electronics.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Replacement Keys NOTE: Only keys that have been programmed to the vehicle electronics can be used to start the vehicle. Once a Sentry Key has been programmed to a vehicle, it can not be programmed to any other vehicle. At the time of purchase, the original owner is provided with a four digit PIN number. This number is required for dealer replacement of keys.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 The new Sentry Key has been programmed. The Keyless Entry Transmitter will also be programmed during this procedure. • This device must accept any interference that may be received, including interference that may cause undesired operation. Repeat this procedure to program up to a total of 8 keys. If you do not have a programmed sentry key, contact your dealer for details.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE DOOR LOCKS Manual Door Locks Lock the doors by pushing up on the lock knob on each door trim panel. If the lock knob is up when you shut the door, the door will lock. Therefore, make sure the keys are not inside the vehicle before closing the door. WARNING! • For personal security and safety in the event of an accident, lock the vehicle doors as you drive as well as when you park and leave the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Power Door Locks A power door lock switch is on each front door trim panel. Use this switch to lock or unlock the doors. 17 or closing the door will allow the locks to operate. A chime will sound if the key is in the ignition and a door is open, as a reminder to remove the key. Automatic Door Locks The doors will lock automatically on vehicles with power door locks if: 1. The Auto Lock feature is enabled, 2. the transmission is in gear, 3.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Auto Unlock The doors will unlock automatically on vehicles with power door locks if: 1. The Auto Unlock feature is enabled, 2. the transmission was in gear and the vehicle speed returned to 0 mph (0 km/h), 3. the transmission is in NEUTRAL or PARK, 4. the driver door is opened (excluding liftgate), 5. the doors were not previously unlocked and 6. the vehicle speed is 0 mph (0 km/h).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To activate the system, open the rear door and move the child lock control, located near the door’s rear latch, to the ON position. 19 When the child lock system is engaged the door can be opened only by using the outside door handle even though the inside door lock is in the unlocked position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: If the key is in the ignition switch, then all buttons on that transmitter will be disabled. The buttons on the remaining transmitters will work. If the vehicle is shifted out of PARK, all the transmitter buttons are disabled for all keys. To unlock the doors and liftgate: Press and release the UNLOCK button on the transmitter once to unlock the driver’s door, or twice to unlock all doors and liftgate. The illuminated entry system also turns on.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To lock the doors and liftgate: Press and release the LOCK button on the transmitter to lock all doors and liftgate. The horn will chirp once to acknowledge the signal. If desired, the “Sound Horn On Lock” feature can be turned on and off by referring to the Customer Programmable Features of the “Electronic Vehicle Information Center (EVIC)” section or by following these steps. 1. Press the LOCK button for 4 to 10 seconds. 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Open/Close Power Liftgate — If Equipped Press the LIFTGATE button twice within five seconds to open/close the power liftgate. The liftgate will beep for 2 seconds and then open/close. If the button is pushed while the liftgate is being power closed, the liftgate will reverse to the full open position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE General Information This device complies with part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired operation. If your Remote Keyless Entry transmitter fails to operate from a normal distance, check for these two conditions. 1. A weak battery in the transmitter.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Remove and replace the battery. Avoid touching the new battery with your fingers. Skin oils may cause battery deterioration. If you touch a battery, clean it with rubbing alcohol. 3. To reassemble the transmitter case, snap the two halves together. Make sure there is an even “gap” between the two halves. Test transmitter operation. VEHICLE THEFT ALARM This system monitors the vehicle doors and ignition switch for unauthorized entry or operation.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To disarm the system: Press the UNLOCK button on the keyless entry transmitter. Also, using a valid sentry key and moving the ignition switch to the ON/START position will disarm the system. If you disarm the system and access the liftgate area, the system must be rearmed, as described previously, when closing the liftgate. If something has triggered the system in your absence, the horn will sound three times when you disarm the system.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The alarm system will be activated when the battery is connected if the system was previously armed. The exterior lights will flash, the horn will sound, and the ignition will not start the vehicle. If this occurs, disarm the system. LIFTGATE The liftgate can be unlocked using the remote keyless entry or by activating the power door lock switches located on the front doors. Once unlocked, the liftgate can be opened or closed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: • If a power malfunction to the power liftgate latch should occur, an emergency liftgate latch release can be used to open the liftgate. The emergency liftgate latch release can be accessed through a snap-in cover located on the liftgate trim panel.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The power liftgate may also be opened by pressing the switch located on the overhead console. WARNING! During power operation, personal injury or cargo damage may occur. Ensure the liftgate travel path is clear. Make sure the liftgate is closed and latched before driving away.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 • The power liftgate must be in the full open position for any of the close buttons to operate. If the liftgate is not fully open, press the open button to fully open the liftgate and then press close. • If the power liftgate encounters multiple obstructions within the same cycle, the system will automatically stop and must be opened or closed manually.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Gas props support the liftgate in the open position. However, because the gas pressure drops with temperature, it may be necessary to assist the props when opening the liftgate in cold weather. WINDOWS Power Windows The window controls on the driver’s door control all the door windows. There are single window controls on each passenger door trim panel which operate the passenger door windows.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE When the lock switch is pressed the window controls on the passenger doors will not illuminate and the passenger windows will be disabled. Auto Down Feature All the power window switches have an auto down feature. Press the window switch to the second detent, release, and the window will go down automatically. To open the window part way, press the window switch to the first detent and release it when you want the window to stop.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Please pay close attention to the information in this section. It tells you how to use your restraint system properly to keep you and your passengers as safe as possible. WARNING! In a collision, you and your passengers can suffer much greater injuries if you are not properly buckled up. You can strike the interior of your vehicle or other passengers, or you can be thrown out of the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 WARNING! WARNING! • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • Be sure everyone in your vehicle is in a seat and using a seat belt properly. • Wearing a seat belt incorrectly is dangerous.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2. The seat belt latch plate is near the seatback of the front seats and next to your arm in the rear seats. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to allow the belt to go around your lap.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click”. 35 WARNING! • A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you as well.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision. WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 6. To release the belt, push the red button on the buckle. The belt will automatically retract to its stowed position. If necessary, slide the latch plate down the webbing to allow the belt to retract fully. WARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE As a guide, if you are shorter than average, you will prefer a lower position, and if you are taller than average, you’ll prefer a higher position. When you release the anchorage, try to move it up or down to make sure that it is locked in position. Lap/Shoulder Belt Untwisting Procedure Use the following procedure to untwist a twisted lap/ shoulder belt. 1. Position the latch plate as close as possible to the anchor point.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 2. At about 6 to 12 inches (15 to 30 cm) above the latch plate, grasp and twist the belt webbing 180° to create a fold that begins immediately above the latch plate. 2 4. Continue to slide the latch plate up until it clears the folded webbing. 3. Slide the latch plate upward over the folded webbing. The folded webbing must enter the slot at the top of the latch plate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seat Belt Pretensioners The seat belts for both front seating positions are equipped with pretensioning devices that are designed to remove slack from the seat belt in the event of a collision. These devices improve the performance of the seat belt by assuring that the belt is tight about the occupant early in a collision. Pretensioners are designed to work for all size occupants.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 The Enhanced Warning System (BeltAlert™) can be enabled or disabled by your authorized dealer or by following these steps: 4. Turn off the engine. A single chime will sound to signify that you have successfully completed the programming. NOTE: The following steps must occur within the first 60 seconds of the ignition switch being turned to the ON or START position. DaimlerChrysler does not recommend deactivating the Enhanced Warning System (BeltAlert).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Keep the belt low so that it does not come across the abdomen. That way the strong bones of the hips will take the force if there is a collision. Seat Belt Extender If a seat belt is too short, even when fully extended and when the adjustable upper shoulder belt anchorage (if equipped) is in its lowest position, your dealer can provide you with a seat belt extender. This extender should be used only if the existing belt is not long enough.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 Driver and Front Passenger Supplemental Restraint System - Airbag This vehicle has airbags for both the driver and front passenger as a supplement to the seat belt restraint systems. The driver’s front airbag is mounted in the center of the steering wheel. The passenger’s front airbag is mounted in the instrument panel, above the glove compartment. The words SRS AIRBAG are embossed on the airbag covers.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE This vehicle is also equipped with a driver inflatable knee blocker located on the instrument panel below the steering column. This vehicle may also be equipped with left and right side curtain airbags to protect the driver and passengers sitting next to a window. If the vehicle is equipped with side curtain airbags, they are located above the side windows. Their covers are also labeled SRS AIRBAG.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Do not put anything on or around the airbag covers or attempt to manually open them. You may damage the airbags and you could be injured because the airbags are not there to protect you. These protective covers for the airbag cushions are designed to open only when the airbags are inflating.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 1. Children 12 years old and under should always ride buckled up in a rear seat. Infants in rear facing child restraints should NEVER ride in the front seat of a vehicle with a passenger front airbag. An airbag deployment can cause severe injury or death to infants in that position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly. In some collisions the airbags won’t deploy at all. Always wear your seat belts even though you have airbags. • Being too close to the steering wheel or instrument panel during front airbag deployment could cause serious injury. Airbags need room to inflate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE How The Airbag Systems Work • The airbag control module determines if an impact is severe enough to require the airbags to inflate. Based on the level of collision severity, the control module determines the proper rate of inflation. The front airbag inflators are designed to provide different rates of airbag inflation. The airbag control module will not detect roll over collisions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • When the airbag control module detects a collision requiring the Front Airbags , it signals the inflator units. A large quantity of nontoxic gas is generated to inflate the front airbags. Different front airbag inflation rates are possible, these rates are determined by the airbag control module based on collision severity. The front airbag covers separate and fold out of the way as the front airbags inflate to their full size.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The Driver Inflatable Knee Blocker inflates rearward towards the driver’s knees to help protect the knees and position you for the best interaction with the front airbag. The Driver Inflatable Knee Blocker fully inflates in about 50 milliseconds, this is only about half of the time it takes you to blink your eyes. It then quickly deflates while helping to protect the driver’s knees.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The airbag material may sometimes cause abrasions and/or skin reddening to the driver and front passenger as the airbags deploy and unfold. The abrasions are similar to friction rope burns or those you might get sliding along a carpet or gymnasium floor. They are not caused by contact with chemicals. They are not permanent and normally heal quickly.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Maintaining Your Airbag System WARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. You could be injured because the airbags are not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the steering wheel hub trim cover or the upper right side of the instrument panel. Do not modify the front bumper, vehicle body structure, or frame.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Child Restraint Everyone in your vehicle needs to be buckled up at all times — babies and children, too. Every state in the United States and all Canadian provinces require that small children ride in proper restraint systems. This is the law, and you can be prosecuted for ignoring it. Children 12 years and under should ride properly buckled up in a seat appropriate for their age and size.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The lower anchor bars of the LATCH System are located where the seat back meets the seat cushion. The tether anchors are located on the rear surface of the seat. Child restraint systems designed to be compatible with the vehicles LATCH System are now available. LATCH child restraints make installation into the vehicle simple and convenient. When using the LATCH System, always follow the child restraint manufactures installation instructions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 NOTE: If your child restraint seat is not LATCH compatible, install the restraint using the vehicle seat belts. Tether Anchors There are tether strap anchorages behind all second row seating positions and the driver’s side third row seating position. The tether anchors are located in the rear surface of the seat.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE When the tether anchorage is used in the third row seating position, the strap should be positioned straight over the top of the seatback. Infants and Children There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt. Always check the child seat owner’s manual to ensure you have the right seat for your child.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The infant carrier is only used rearward-facing in the vehicle. It is recommended for children who weigh up to about 9 kg (20 lbs). 9Convertible9 child seats can be used either rearward-facing or forward-facing in the vehicle. Convertible child seats often have a higher weight limit in the rearward-facing direction than infant carriers do, so they can be used rearward-facing by children who weigh more than 9 kg (20 lbs) but are less than one year old.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint. • A rearward facing child restraint should only be used in a rear seat.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Buckle the child into the seat according to the child restraint manufacturer’s directions. • When your child restraint is not in use, secure it in the vehicle with the seat belt or remove it from the vehicle. Don’t leave it loose in the vehicle. In a sudden stop or collision, it could strike the occupants or seatbacks and cause serious personal injury.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE have tether straps, and you are urged to take advantage of all of the available attachments provided with your child restraint in any vehicle. Not all child restraint systems will be installed as we have described here. Again, carefully follow the instructions that come with the child restraint system. WARNING! Improper installation of a child restraint to the LATCH anchorages can lead to failure of an infant or child restraint.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Transporting Pets Airbags deploying in the front seat could harm your pet. An unrestrained pet could be thrown about and possibly injured, or injure a passenger during panic braking or in a collision. Pets should be restrained in the rear seat in pet harnesses or pet carriers that are secured by seat belts. ENGINE BREAK-IN RECOMMENDATIONS A long break-in period is not required for the engine in your new vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE SAFETY TIPS WARNING! Exhaust Gas WARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO) which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (CO) follow the safety tips below. Do not run the engine in a closed garage or in confined areas any longer than needed to move your vehicle in or out of the area.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag Light The light should come on and remain on for 6 to 8 seconds as a bulb check when the ignition switch is first turned ON. If the LED is not lit during starting, have it checked. If the light stays on or comes on while driving, have the system checked by an authorized dealer. Defroster Check operation by selecting the defrost mode and place the blower control on high speed. You should be able to feel the air directed against the windshield.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 3 m Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69 ▫ Heated Remote Control Mirrors . . . . . . . . . . . .72 ▫ Inside Day/Night Mirror . . . . . . . . . . . . . . . . .69 ▫ Illuminated Vanity Mirrors . . . . . . . . . . . . . . . .73 ▫ Automatic Dimming Mirror — If Equipped . . . .70 m Hands–Free Communication (UConnect™) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE m Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85 ▫ Plastic Grocery Bag Retainer . . . . . . . . . . . . . .98 ▫ 10–Way Driver’s Power Seat — If Equipped . . .85 m Adjustable Pedals — If Equipped . . . . . . . . . . . .99 ▫ 8–Way Driver’s Power Seat — If Equipped . . . .85 m To Open And Close The Hood . . . . . . . . . . . . . 100 ▫ 4–Way Passenger’s Power Seat . . . . . . . . . . . . .85 m Lights . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 67 ▫ Fog Lights — If Equipped . . . . . . . . . . . . . . . 106 ▫ To Activate . . . . . . . . . . . . . . . . . . . . . . . . . . 112 ▫ Turn Signals . . . . . . . . . . . . . . . . . . . . . . . . . 106 ▫ To Set At A Desired Speed . . . . . . . . . . . . . . . 112 ▫ Highbeam/Lowbeam Select Switch . . . . . . . . . 107 ▫ To Deactivate . . . . . . . . . . . . . . . . . . . . . . . . 112 ▫ Passing Light . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Erasing Homelink Buttons . . . . . . . . . . . . . . . 119 ▫ Front Seat Cupholders . . . . . . . . . . . . . . . . . . 126 ▫ Reprogramming a Single Homelink Button . . . 120 ▫ Second Row Seat Cupholders . . . . . . . . . . . . . 126 ▫ Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 ▫ Third Row Seat Cupholders . . . . . . . . . . . . . . 126 m Power Sunroof — If Equipped . . . . . . . . . . . . . 121 m Storage . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Day/Night Mirror Adjust the mirror to center on the view through the rear window. A two point pivot system allows for horizontal and vertical adjustment of the mirror. 69 Annoying headlight glare can be reduced by moving the small control under the mirror to the night position (toward rear of vehicle). The mirror should be adjusted while set in the day position (toward windshield).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Dimming Mirror — If Equipped If the switch is in the “Auto” position the mirror will automatically adjust for annoying headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light in the mirror will illuminate to indicate when this feature is on. CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Outside Mirror — Driver’s Side Adjust the outside mirror to center on the adjacent lane of traffic, with a slight overlap of the view obtained on the inside mirror. Outside Mirror — Passenger’s Side Adjust the convex outside mirror so you can just see the side of your vehicle in the portion of the mirror closest to the vehicle. This type of mirror will give a much wider view to the rear, and especially of the lane next to your vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Remote-Control Mirrors Use the mirror select switch, located on the driver’s door trim panel above the power window switches, to adjust the view obtained in the outside mirrors. Press the rocker switch to the L or R for Left or Right mirror selection. Use the center off position to guard against accidentally moving a mirror position. Select a mirror and press one of the four arrows for the direction you want the mirror to move.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Illuminated Vanity Mirrors An illuminated vanity mirror is on the sun visor. To use the mirror, rotate the sun visor down and swing the mirror cover upward. The lights turn on automatically. Closing the mirror cover turns off the lights. 73 Sun Visor Extension This feature has a pull out extension on the sun visor for increased coverage.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE The UConnect™; phone book enables you to store up to 32 names and four numbers per name. This system is driven through your Bluetooth™ Hands-Free Profile cellular phone. UConnect™ features Bluetooth™ technology - the global standard that enables different electronic devices to connect to each other without wires or a docking station, so UConnect™ works no matter where you stow your cellular phone (be it your purse, pocket, or briefcase).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE prompts as well as the other party’s voice in a conversation will be played over your vehicle’s stereo system. The volume of the UConnect™ system can be controlled through your normal stereo controls. The radio display will be used for visual prompts from the UConnect™ system such as caller ID. Operation Voice commands can be used in the operation of the UConnect™ system and to navigate through the UConnect™ menu structure.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The UConnect™ system will then prompt you to begin the cellular phone pairing process on your cellular phone. Please see your cellular phone user’s manual for instructions on how to complete this step. • For identification purposes, you will be prompted to give the UConnect™ system a name for your cellular phone. Each cellular phone that is paired should be given a unique phone name.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Add Names to Your UConnect™ Phonebook • Press the “Phone” button to begin. • After the 9Ready9 prompt, say 9Phonebook New Entry9. • When prompted, say the name of the new entry. • Next, enter the number designation (e.g. “Home”, “Work”, “Mobile”, or “Pager”). This will allow you to have multiple numbers for each phonebook entry.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Phonebook edit can be used to add another phone number to a name entry that already exists in the phonebook. For example, the entry John Doe may have a mobile and a home number, but you can add John Doe’s work number later through phonebook edit. Delete Entries in the UConnect™ Phonebook • Press the ’Phone’ button to begin. • After the 9Ready9 prompt, say 9Phonebook Delete9.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The UConnect™ system will play the names of all the phonebook entries. • To call one of the names in the list, press the ’Voice Recognition’ button during the playing of the desired name and say 9Call9. • The UConnect™ system will then prompt you as to number designation you wish to call. • The selected number will be dialed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Making a Second Call while Current Call in Progress To make a second call while you are currently in a call, press the ’Voice Recognition’ button and say 9Dial9 or 9Call9 followed by the phone number or phonebook entry you wish to call. The first call will be on hold while the second call is in progress.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 81 Phone Redial Delete Paired Cellular Phones • Press the ’Phone’ button to begin. • Press the ’Phone’ button to begin. • After the 9Ready9 prompt, say 9Redial9. • After the 9Ready9 prompt, say 9Setup Phone Pairing9. • The UConnect™ system will call the last number that was dialed on your cellular phone. This may not be the last number dialed by your UConnect™ system. • At the next prompt, say 9Delete9.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE If you would like to connect or disconnect the Bluetooth™ connection between a paired cellular phone and the UConnect™ system, follow the instruction described in your cellular phone user’s manual. List Paired Cellular Phone Names • Press the ’Phone’ button to begin. • After the 9Ready9 prompt, say 9Setup List Phones9 and the UConnect™ system will play the phone names of all paired cellular phones in order from highest priority to lowest priority.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83 pin. This method can also be used in instances where you are pressing a number on your keypad to navigate through a menu structure or to enter a number for a pager. Turning Confirmation Prompts On/Off Turning confirmation prompts off will stop the system from confirming your choices (e.g. the UConnect™ system will not repeat a phone number before you dial it).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Dialing Using the Cellular Phone Keypad You can dial a phone number with your cellular phone keypad and still use the UConnect™ system. By dialing a number with your paired Bluetooth™ cellular phone, the audio will be played through your vehicle’s stereo system. The UConnect™ system will work the same as if you dialed the number using voice recognition.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE SEATS 10–Way Driver’s Power Seat — If Equipped The driver’s power seat switches are located on the driver’s front door trim panel. The bottom switch controls up/down, forward/rearward, and tilt adjustment. The top switch controls the seatback recline adjustment and the middle switch controls the lumbar adjustment. 85 WARNING! Adjust the seat only while the vehicle is parked. Adjusting a seat while the vehicle is moving is dangerous.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Do not place any article under a power seat or impede its ability to move as it may cause damage to the seat controls. Seat travel may become limited if movement is stopped by an obstruction in the seat’s path. Adjustable Head Restraints Head restraints can reduce the risk of whiplash injury in the event of impact from the rear. Pull up or push down on the head restraint so that the upper edge is as high as practical.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 The controls for the second row heated seats are located on the center console between the seats. Press the switch once to select a heat setting (high or low) and press the switch a second time in the same direction to turn the heated seat off. The indicator light will show when LOW or HIGH heat is ON. Press the switch once to select a heat setting (high or low) and press the switch a second time in the same direction to turn the heated seat off.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: • If the lights in the second row heated seat switch begin to flash when the switch is pressed, it indicates that the heated seat is not functioning properly and that service is required. See your authorized dealer for service. • Once a heat setting is selected, heat will be felt within 2 to 3 minutes. • The heated seats will turn off when the ignition switch is turned to the OFF position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The vehicle must be in Park to recall memory positions. If a recall is attempted when the vehicle is not in Park, a message will be displayed in the Electronic Vehicle Information Center (EVIC). To recall memory positions press memory button number 1 if you are recalling the memory position for driver one or press memory button number 2 if you are recalling the memory position for driver two.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 6. Press and release the SET (S) button located on the driver’s door. A light in the button will flash telling you that you are in the set memory mode. You have five seconds to complete the next step. 7. Within 5 seconds, press and release button 1 or 2 on the driver’s door. A chime will sound signaling you that the driver memory has been set.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 5. Within 5 seconds, press and release the UNLOCK button on the remote keyless entry transmitters. A chime will sound signaling you that the transmitter link has been successfully disabled. A message will also be displayed in the Electronic Vehicle Information Center (EVIC), indicating the transmitter has been disabled. 91 seatback to its normal position. Using body pressure, lean forward and rearward on the seat to be sure the seatback has latched.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or fatally injured. Use the recliner only when the vehicle is parked. Second Row Manual Seat Adjuster The adjusting bar is located under the front of the seat. Pull the bar up and move the seat to the desired position. Release the bar to lock the seat into position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Adjust the seat only while the vehicle is parked. Adjusting a seat while the vehicle is moving is dangerous. The seat belt might not be properly adjusted and you could be injured. 93 4. Pull up on the seatback release lever located on the outboard side of the seat labeled “1” and fold the seatback down. 3 Second Row Fold & Tumble Seats The second row seats can be folded and tumbled forward for easy access to the third seat or rear cargo area.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 5. Pull up on the release handle labeled “2” and lift firmly to tumble the seat fully forward. If the seat contacts the rear of the front seat, move the front seat forward. To relatch the seat, tilt the seat rearward and push down firmly to engage the rear attachments. Then lift the seatback release lever labeled “1” and pull the seatback up to return it to its full upright position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 To fold and tumble the seat forward, follow these steps: 1. Pull up on the seatback release handle “1” located on the back of the seat to fold the seatback down. 3 2. Pull the release strap “2” located at the bottom of the seat to lift and tumble the seat forward. To relatch the seat, tilt the seat rearward and push down firmly to engage the rear attachments.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Third Row Seating Flexibility The third row seats may be used with either or both seatbacks folded forward for additional storage space. To fold the seat, remove any objects from in front of or on the seat. Then pull handle located on the seatback and push it forward. WARNING! Do not sit in the 3rd row seat with the second row seatbacks folded or with the second row seats folded and tumbled.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Not all head restraints in this vehicle are the same. Head restraints from one seating position should not be removed and installed in any other seating position. In a collision, serious injury or death may result if the proper head restraint is not installed on each seat. • The cargo area in the rear of the vehicle should not be used as a play area by children. They could be seriously injured in a collision.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Pull on the load floor strap and lift the panel from the driver’s second row seatback over the center console and onto the passenger second row seat. NOTE: Be sure to reattach the strap to secure the load floor panel when not in use. Plastic Grocery Bag Retainer Retainer hooks which will hold plastic grocery bag handles are built into the seatbacks of all front seats. The floor supports the partial weight of the bagged goods.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99 ADJUSTABLE PEDALS — IF EQUIPPED This feature allows both the brake and accelerator pedals to move toward or away from the driver to provide improved position with the steering wheel. The adjustable pedal system is designed to allow a greater range of driver comfort for steering wheel tilt and seat position. The switch is located on the drivers door trim panel next to the power seat switches.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The pedals cannot be adjusted when the vehicle is in R (Reverse) or when the Speed Control is ON. A message will be displayed in the Electronic Vehicle Information Center (EVIC) if the pedals are attempted to be adjusted when the system is locked out (“Adjustable Pedal Disabled — Cruise Control Engaged” or “Adjustable Pedal Disabled — Vehicle In Reverse”).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 3 Next, push to the left the safety catch located under the front edge of the hood, near the center. Use the hood prop rod to secure the hood in the open position. To prevent possible damage, do not slam the hood to close it. Lower the hood until it is open approximately 15 cm (6 inches) and then drop it. This should secure both latches. Never drive your vehicle unless the hood is fully closed, with both latches engaged.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! If the hood is not fully latched, it could fly up when the vehicle is moving and block your forward vision. You could have a collision. Be sure all hood latches are fully latched before driving. LIGHTS Overhead Console Map/Reading Lights These lights are mounted between the sun visors on the overhead console. Each light is turned ON by pressing the lens. Press the lens a second time to turn the light OFF.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 Interior Lights The interior lights come on when a door is opened. The interior lights will automatically turn off in about 15 minutes if a door is left open or the dimmer control is left in the Dome light position. Turn the ignition switch ON to restore the interior light operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To change the brightness of the instrument panel lights, rotate the center portion of the Multi-Function Lever up or down. Dimmer Control With the parking lights or headlights on, rotating the dimmer control for the interior lights on the Multi-Function Lever upward will increase the brightness of the instrument panel lights. Dome Light Position Rotate the dimmer control completely upward to the second detent to turn on the interior lights.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Parade Mode (Daytime Brightness Feature) Rotate the dimmer control upward to the first detent. This feature brightens the odometer and radio display when the parking lights or headlights are on during daylight conditions. Automatic Headlights This system automatically turns your headlights ON or OFF based on ambient light levels. To turn the system ON, turn the end of the Multi-Function Lever to the third detent position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To activate the delay feature, turn off the ignition switch while the headlights are still on. Then turn off the headlights within 45 seconds. The 90 second delay interval begins when headlight switch is turned off. If the headlights or park lights are turned back on or the ignition switch is turned on, the delay will be cancelled. If the headlights are turned off before the ignition, they will turn off in the normal manner.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 Highbeam/Lowbeam Select Switch Pull the Multi-Function Lever towards you to switch the headlights to HIGH beam. Pull the Lever a second time to switch the headlights to LOW beam. Passing Light You can signal another vehicle with your headlights by lightly pulling the Multi-Function Lever toward you. This will cause the headlights to turn on at high beam and remain on until the lever is released.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE If the lever is pulled while in the OFF position, the wipers will operate for two wipe cycles, then turn OFF. Mist Feature Push down on the wiper lever to activate a single wipe to clear off road mist or spray from a passing vehicle. As long as the lever is held down, the wipers will continue to operate.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 Rotating the center of the switch up to the DEL (Delay) position or the ON position will activate the rear wiper. Push the lever forward to initiate the rear wash function in any of the three positions. The washer pump will continue to operate as long as the lever is pressed. Upon release, the rear wiper will cycle two times before returning to the set position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE TILT STEERING COLUMN To tilt the column, pull the lever, located behind the turn signal control, toward you and move the steering wheel up or down, as desired. Release the lever to lock the steering wheel firmly in place. WARNING! Tilting the steering column while the vehicle is moving is dangerous. Without a stable steering column, you could lose control of the vehicle and have an accident. Adjust the column only while the vehicle is stopped.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 • The Traction Control system will make buzzing or clicking sounds when in operation. ELECTRONIC SPEED CONTROL When engaged, this device takes over the accelerator operation at speeds greater than 30 mph (50 km/h). The speed control switches are located on the steering wheel. To turn the system back ON, press the switch a second time until the traction control Indicator turns OFF.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Activate: Push the “ON/OFF” button once and the CRUISE indicator located near the instrument cluster odometer will illuminate showing the electronic speed control system is on. To turn the system OFF, push the “ON/OFF” button again and the system and indicator will turn off. WARNING! Leaving the Electronic Speed Control system on when not in use is dangerous. You could accidently set the system or cause it to go faster than you want.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Resume Speed: To resume a previously set speed, push and release the “ACCEL/RESUME” button. Resume can be used at any speed above 25 mph (40 km/h). To Vary the Speed Setting: When the speed control is set, speed can be increased by pressing and holding the “ACCEL/RESUME” button. When the button is released, a new set speed will be established. Tapping the “ACCEL/RESUME” button once will result in a 2 mph (3 km/h) speed increase.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Speed Control can be dangerous where the system can’t maintain a constant speed. Your vehicle could go too fast for the conditions, and you could lose control. An accident could be the result. Don’t use Speed Control in heavy traffic or on roads that are winding, icy, snow-covered, or slippery.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE The lights also turn on when a front door, a rear door or the liftgate is opened. The lights will also turn on when the unlock button on the remote keyless entry transmitter is pressed. Sunglasses Storage At the rear of the console a compartment is provided for the storage of a pair of sunglasses. Press the door latch to open the compartment. The door will slowly rotate to an open position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Programming HomeLink NOTE: When programming a garage door opener, it is advised to park outside the garage. Some vehicles may require the ignition switch to be turned to the second (or 9accessories9) position for programming and/or operation of HomeLink. It is also recommended that a new battery be placed in the hand-held transmitter of the device being programmed to HomeLink for quicker training and accurate transmission of the radio-frequency signal. 1.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Your motorized door or gate will open and close while you are training the Universal Transceiver. Do not train the transceiver if people or pets are in the path of the door or gate. A moving door or gate can cause serious injury or death to people and pets or damage to objects. 2. Position the end of your hand-held transmitter 1-3 inches (3-8 cm) away from the HomeLink buttons while keeping the indicator light in view. 3.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE If the indicator light blinks rapidly for two seconds and then turns to a constant light continue with (Programming( steps 6-8 to complete the programming of a rolling code equipped device (most commonly a garage door opener). 6. At the garage door opener receiver (motor-head unit) in the garage, locate the 9learn9 or 9smart9 button. This can usually be found where the hanging antenna wire is attached to the motor-head unit. 7.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE If you live in Canada or you are having difficulties programming a gate operator by using the 9Programming9 procedures (regardless of where you live), replace (Programming HomeLink( step 3 with the following: NOTE: If programming a garage door opener or gate operator, it is advised to unplug the device during the 9cycling9 process to prevent possible overheating. 3.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Reprogramming a Single HomeLink Button To program a device to HomeLink using a HomeLink button previously trained, follow these steps: This device complies with part 15 of FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following conditions: 1. Press and hold the desired HomeLink button. Do NOT release the button. • This device may not cause harmful interference. 2. The indicator light will begin to flash after 20 seconds.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE POWER SUNROOF — IF EQUIPPED The power sunroof switches are located between the sun visors on the overhead console. 121 Press and hold the switch rearward to fully open the sunroof. The sunroof can be stopped at any position between closed and full open. Momentarily pressing the switch rearward will activate the Express Open Feature, causing the sunroof to open automatically. Press and hold the button in the center of the sunroof switch to open the vent.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Express Open Feature The sunroof is equipped with an intermediate stop or comfort stop position. This feature is designed to eliminate wind buffeting at vehicle speeds between 20-40 mph (32-64 km/h). To operate this feature, momentarily press the switch rearward to activate the Express Open Feature and the glass will automatically stop at the comfort stop position. Pressing the switch rearward again will fully open the sunroof.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Never leave children in a vehicle, with the keys in the ignition switch. Occupants, particularly unattended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death. • In an accident, there is a greater risk of being thrown from a vehicle with an open sunroof. You could also be seriously injured or killed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ELECTRICAL POWER OUTLETS There are two 12 volt power outlets located on the instrument panel below the radio. The driver’s side outlet is controlled by the ignition switch and the passenger side outlet is connected directly to the battery. The driver’s side outlet will also operate a conventional cigar lighter unit (if equipped with an optional Smoker’s Package).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE The outlets include tethered caps labeled with a key or battery symbol indicating the power source. The passenger side instrument panel and center console outlets are powered directly from the battery, items plugged into these outlets may discharge the battery and/or prevent engine starting. The passenger side and center console outlets are protected by an automatic reset circuit breaker. The automatic circuit breaker restores power when the overload is removed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CUPHOLDERS Front Seat Cupholders The cupholders are located in the forward edge of the center console. Push down on the forward edge of the console to release the cupholders. Press the cover up when the cupholders are no longer needed. Second Row Seat Cupholders The second row seat cupholders are located in the forward edge of the center console located between the second row seats. Push down on the forward edge of the console to release the cupholders.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Cargo Storage Bin The storage bin is located in the floor of the rear cargo area. To open lift up on the handle. 127 Retractable Cargo Area Cover — If Equipped To cover the cargo area: 1. Fold down the third row seatbacks. 2. Unfold the cargo cover extensions and lock into place. 3. Insert the pins on the ends of the cover into the slots located on the trim panel behind the second row seatbacks. 4. Grasp the center portion of the cover flap.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! 3. Insert the pins on the ends of the cover into the slots located on the trim panel behind the third row seatbacks. In an accident a cargo cover loose in the vehicle could cause injury. It could fly around in a sudden stop and strike someone in the vehicle. Do not store the cargo cover on the cargo floor or in the passenger compartment. Remove the cover from the vehicle when taken from its mounting. Do not store in the vehicle. 4.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Cargo tie-down hooks are not safe anchors for a child seat tether strap. In a sudden stop or collision a hook could pull loose and allow the child seat to come loose. A child could be badly injured. Use only the anchors provided for child seat tethers. • The weight and position of cargo and passengers can change the vehicle center of gravity and vehicle handling.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ROOF LUGGAGE RACK — IF EQUIPPED The crossbars and siderails are designed to carry the weight on vehicles equipped with a luggage rack. The load must not exceed 150 lbs (68 kg), and should be uniformly distributed over the luggage rack crossbars. Distribute cargo weight evenly on the roof rack crossbars. The roof rack does not increase the total load carrying capacity of the vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE The tie down holes on the cross bar ends should always be used to tie down the load. Check the straps frequently to be sure that the load remains securely attached. 131 CAUTION! • To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity of 150 lbs (68 kg). Always distribute heavy loads as evenly as possible and secure the load appropriately.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Cargo must be securely tied before driving your vehicle. Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage. Follow the Roof Rack Cautions when carrying cargo on your roof rack. LOAD LEVELING SYSTEM The automatic load leveling system will provide a level riding vehicle under most passenger and cargo loading conditions.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS m Instruments And Controls . . . . . . . . . . . . . . . . . 136 m Electronic Digital Clock . . . . . . . . . . . . . . . . . . 154 m Instrument Cluster . . . . . . . . . . . . . . . . . . . . . . 137 ▫ Clock Setting Procedure . . . . . . . . . . . . . . . . . 154 m Instrument Cluster Descriptions . . . . . . . . . . . . 138 m Sales Code RAH—AM & FM Stereo Radio With CD Player And CD/DVD Changer Controls . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Radio Operation . . . . . . . . . . . . . . . . . . . . . . 160 m Remote Sound System Controls . . . . . . . . . . . . . 178 ▫ Tape Player Operation . . . . . . . . . . . . . . . . . . 164 ▫ Radio Operation . . . . . . . . . . . . . . . . . . . . . . 178 ▫ CD Player Operation . . . . . . . . . . . . . . . . . . . 166 ▫ Tape Player . . . . . . . . . . . . . . . . . . . . . . . . . 178 ▫ CD/DVD Changer Operation — If Equipped . 168 ▫ CD Player . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 135 m Navigation System — If Equipped . . . . . . . . . . . 182 ▫ Dual-Zone Automatic Temperature Control . . . 183 m Climate Controls . . . . . . . . . . . . . . . . . . . . . . . 183 ▫ Electric Rear Window Defroster . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENTS AND CONTROLS
UNDERSTANDING YOUR INSTRUMENT PANEL 137 INSTRUMENT CLUSTER 4
UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTIONS 1. Voltage Light This light monitors the electrical system voltage. The light should turn on momentarily as the engine is started. If the light stays on or turns on while driving, it indicates a problem with the charging system. Immediate service should be obtained. 2. Temperature Gauge The temperature gauge shows engine coolant temperature.
UNDERSTANDING YOUR INSTRUMENT PANEL WARNING! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call a service center if your vehicle overheats. If you decide to look under the hood yourself, see Section 7 of this manual. Follow the warnings under the Cooling System Pressure Cap paragraph. 3. Fuel Gauge The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON position.
UNDERSTANDING YOUR INSTRUMENT PANEL is not functioning and that service is required. However, the conventional brake system will continue to operate normally if the BRAKE warning light is not on. indicated by the Brake Warning Light which will turn on when the brake fluid level in the master cylinder has dropped below a specified level. If the ABS light is on, the brake system should be serviced as soon as possible to restore the benefits of Anti-Lock brakes.
UNDERSTANDING YOUR INSTRUMENT PANEL Vehicles equipped with Anti-Lock brakes (ABS), are also equipped with Electronic Brake Force Distribution (EBD). In the event of an EBD failure, the Brake Warning Light will turn on along with the ABS Light. Immediate repair to the ABS system is required. The operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON position. The light should illuminate for approximately two seconds.
UNDERSTANDING YOUR INSTRUMENT PANEL disabled for about 4 minutes until the brakes have cooled. The system will automatically reactivate and turn off the Traction Control Light. 12. AutoStick Light This display indicator illuminates when the gearshift lever is moved to the AutoStick position. 9. Tachometer The red segments indicate the maximum permissible engine revolutions-per-minute (r.p.m. x 1000) for each gear range. Before reaching the red area, ease up on the accelerator. 13.
UNDERSTANDING YOUR INSTRUMENT PANEL release the Trip Odometer button. To reset a trip odometer, display the desired trip odometer to be reset then push and hold the button until the display resets (approximately 2 seconds). 14. Cruise Indicator This display indicator shows that the Speed Control System is ON. 15. Malfunction Indicator Light This light is part of an onboard diagnostic system called OBD that monitors engine and automatic transmission control systems.
UNDERSTANDING YOUR INSTRUMENT PANEL 19. Oil Pressure Warning Light This light shows low engine oil pressure. The light should turn on momentarily when the engine is started. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. A continuous chime will sound when this light turns on. Do not operate the vehicle until the cause is corrected. This light does not show how much oil is in the engine. The engine oil level must be checked under the hood. 20.
UNDERSTANDING YOUR INSTRUMENT PANEL tire to overheat and can lead to tire failure. Underinflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability. Each tire, including the spare, should be checked monthly when cold and set to the recommended inflation pressure as specified in the tire and loading information placard and owner’s manual. 22.
UNDERSTANDING YOUR INSTRUMENT PANEL Pressing the MENU button will change the displayed programming features. Pressing the STEP button will display the available choices. Pressing the MENU button a second time accepts a selected choice. When the appropriate conditions exist, the Electronic Vehicle Information Center (EVIC) displays the following messages.
UNDERSTANDING YOUR INSTRUMENT PANEL • TOO COLD FOR PWR LIFTGATE (with a single chime) • TOO HOT FOR PWR LIFTGATE (with a single chime) • PERFORM SERVICE (with a single chime) • LEFT/RIGHT FRONT DOOR AJAR (one or more, with a single chime if speed is above 1 mph) • LEFT/RIGHT REAR DOOR AJAR (one or more, with a single chime if speed is above 1 mph) • DOOR(S) AJAR (with a single chime) • DOOR(S) AND GATE AJAR (with a single chime) • LIFT GATE AJAR (with a single chime if speed is above 1 mph) • WASHER FLUID
UNDERSTANDING YOUR INSTRUMENT PANEL • SERVICE TIRE SYSTEM SOON (Refer to “Starting And Operating, Tire Section”) • TIRE PRESSURE UNAVAILABLE (Refer to “Starting And Operating, Tire Section”) • TCS SUSPENDED (Traction Control System, with a graphic and single chime) • TCS ACTIVE (Traction Control System, with a graphic) • SERVICE TCS SYSTEM (Traction Control System, with a graphic and single chime) Customer Programmable Features — If Equipped Press the MENU button until one of the following display cho
UNDERSTANDING YOUR INSTRUMENT PANEL Auto Unlock On Exit? When this feature is selected all the vehicle’s doors will unlock when the driver’s door is opened if the vehicle is stopped and the transmission is in P (Park) or N (Neutral) position. Pressing the STEP button when in this display will select “Yes” or “No.
UNDERSTANDING YOUR INSTRUMENT PANEL Flash Lights On Lock/Unlock? When this feature is selected, the front and rear turn signals will flash when the doors are locked or unlocked using the remote keyless entry transmitter. This feature may be selected with or without the sound horn on lock feature selected. Pressing the STEP button when in this display will select “Yes” or “No.
UNDERSTANDING YOUR INSTRUMENT PANEL 151 Reset Service Distance (Displays Only if Service Interval was Changed) When this feature is selected the current accumulated service distance can be reset to the newly selected service interval. Pressing the STEP button when in this display will select “Yes” or “No.” driver can more easily exit the vehicle.
UNDERSTANDING YOUR INSTRUMENT PANEL display “COMPASS CALIBRATING” until the compass is calibrated. The compass will calibrate automatically after approximately 40 seconds if no buttons are pressed and the vehicle is in Park. You may also calibrate the compass by completing one 360° turn in an area free from large metal or metallic objects, the “COMPASS CALIBRATING” EVIC message will turn off and the compass will function normally.
UNDERSTANDING YOUR INSTRUMENT PANEL 153 To set the variance: Turn the ignition switch ON and set the display to Compass. Press the RESET button for approximately 5 seconds but no more than 10 seconds. The “COMPASS VARIANCE” message and the last variance zone number will be displayed. Press the STEP button to select the proper variance zone as shown in the map. Press the RESET button to set the new variance zone and resume normal operation.
UNDERSTANDING YOUR INSTRUMENT PANEL • Off Mode Shows a blank display. • Step Button Push this button to cycle through all the Mini-trip functions. To Reset The Display Pressing and releasing the Reset button once will clear the resettable function currently being displayed. The resettable function is average fuel economy. Reset will only occur if the resettable function is currently being displayed.
UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE RAH—AM & FM STEREO RADIO WITH CD PLAYER AND CD/DVD CHANGER CONTROLS 155 Radio Operation Power/Volume Control Press the ON/VOL control to turn the radio on. Turn the volume control clockwise to increase the volume. NOTE: Power to operate the radio is supplied through the ignition switch. It must be in the ON or ACC position to operate the radio. Mode Press the MODE button to select between, AM, FM, CD, CD/DVD changer or the Satellite Radio (if equipped).
UNDERSTANDING YOUR INSTRUMENT PANEL Seek Press and release the SEEK button to search for the next station in either the AM, FM or Satellite mode. Press the top of the button to seek up and the bottom to seek down. The radio will remain tuned to the new station until you make another selection. Holding the button in will bypass stations without stopping until you release it. Tuning Press the TUNE control up or down to increase or decrease the frequency.
UNDERSTANDING YOUR INSTRUMENT PANEL You may add a second station to each push-button by repeating the above procedure with this exception: Press the SET button twice and SET 2 will show in the display window. Each button can be set for SET 1 and SET 2 in both AM and FM. This allows a total of 10 AM and 10 FM stations to be locked into memory. You can recall the stations stored in SET 2 memory by pressing the pushbutton twice. 1.
UNDERSTANDING YOUR INSTRUMENT PANEL Inserting The Compact Disc CAUTION! This CD player will accept only 4–3/4 inch (12cm) discs only. The use of other sized discs may damage the CD player mechanism. You may either insert or eject a disc with the radio OFF. If you insert a disc with the ignition ON and the radio OFF, the display will show the time of day. If you insert a disc with the ignition OFF, the display will show the time of day for about 5 seconds, then go out.
UNDERSTANDING YOUR INSTRUMENT PANEL RND — Random Play Press the RND button while the CD is playing to activate Random Play. This feature plays the selections on the compact disc in random order to provide an interesting change of pace. Press the SEEK button to move to the next randomly selected track. Press TUNE FF to fast forward through the tracks. Press the FF button a second time to stop the fast forward feature.
UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE RBP—AM & FM STEREO RADIO WITH CASSETTE TAPE PLAYER, CD PLAYER, AND OPTIONAL CD/DVD CHANGER CONTROLS Radio Operation Power/Volume Control Press the ON/VOL control to turn the radio on. Turn the volume control to the right to increase the volume. NOTE: Power to operate the radio is supplied through the ignition switch. It must be in the ON or ACC position to operate the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL Toggle the PTY button to select the following format types: Program Type Adult Hits Classical Classic Rock College Country Information Jazz Foreign Language News Nostalgia Oldies Personality Public Rhythm and Blues Radio Display Adlt Hit Classicl Cls Rock College Country Inform Jazz Language News Nostalga Oldies Persnlty Public R&B Program Type Religious Music Religious Talk Rock Soft Soft Rock Soft Rhythm and Blues Sports Talk Top 40 Weather 161 Radio Display Rel Mu
UNDERSTANDING YOUR INSTRUMENT PANEL The radio display will flash “SEEK” and the selected PTY program type when searching for the next PTY station. If no station is found with the selected PTY program type, the radio will return to the last preset station. If a preset button is activated while in the PTY (Program Type) mode, the PTY mode will be exited and the radio will tune to the preset station.
UNDERSTANDING YOUR INSTRUMENT PANEL Fade The Fade control provides for balance between the front and rear speakers. Press the FADE button in and it will pop out. Adjust the balance and push the button back in. Tone Control The tone controls affect the BASS and TREBLE frequency bands. Each is controlled by a slider control with a detent at the mid position. Moving a control up or down increases or decreases amplification of the band. The mid position provides a balanced output.
UNDERSTANDING YOUR INSTRUMENT PANEL To set the clock, use a ballpoint pen or similar object to press the hour (H) or minute (M) buttons on the radio, The time setting will increase each time you press the button. Press any other button to exit from the clock setting mode. General Information This radio complies with Part 15 of FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following conditions: 1. This device may not cause harmful interference, 2.
UNDERSTANDING YOUR INSTRUMENT PANEL Seek Press the SEEK button up for the next selection on the tape and down to return to the beginning of the current selection. Press the SEEK button up or down to move the track number to skip forward or backward 1 to 7 selections. Press the SEEK button once to move 1 selection, twice to move 2 selections, etc. the display will show the total number of times the SEEK button was pushed. The SEEK function will be cancelled by pressing either the FF/RW or AM/FM button.
UNDERSTANDING YOUR INSTRUMENT PANEL Pinch Roller Release If ignition power or the radio ON/OFF switch are turned off, the pinch roller will automatically retract to protect the tape from any damage. When power is restored to the tape player, the pinch roller will automatically reengage and the tape will resume play. Dolby Noise Reduction The Dolby Noise Reduction System* is on whenever the tape player is on, but may be switched on/off.
UNDERSTANDING YOUR INSTRUMENT PANEL Seek Press the top of the SEEK button for the next selection on the CD. Press the bottom of the button to return to the beginning of the current selection, or return to the beginning of the previous selection if the CD is within the first second of the current selection. Scan Press the SCAN button to play 10 seconds of each selection. Press the SCAN button a second time to cancel this feature.
UNDERSTANDING YOUR INSTRUMENT PANEL To select Satellite Radio (if equipped), press the MODE button until the word SIRIUS™ appears. The following will be displayed in this order: After three seconds, the current channel name and number will be displayed for five seconds. The current program type and channel number will then be displayed for five seconds. The current channel name and number will then be displayed until an action occurs.
UNDERSTANDING YOUR INSTRUMENT PANEL FF/RW — TUNE Press and hold the FF button for fast forward. Press and hold the RW button for fast reverse. The audio output can be heard when fast forward and fast reverse are activated. Disc Down/Program Button 5 Press the DISC (button 5) button to play the previous disc. Seek Press the top of the SEEK button for the next selection on the CD.
UNDERSTANDING YOUR INSTRUMENT PANEL 6 DISC CD/DIGITAL VIDEO DISC (DVD) CHANGER The Rear Seat Audio/Video System allows passengers to listen to a CD or DVD from the 6 disc CD/DVD changer through the headphones, while the front seat passengers listen to either AM/FM, Cassette or CDs from the radio. A remote control is provided for functions such as changing tracks or DVD functions, as well as selecting discs loaded in the 6 disc CD/DVD changer while listening to the Rear Audio/Video System.
UNDERSTANDING YOUR INSTRUMENT PANEL 4. Repeat the process for loading any additional CD/ DVDs. The CD/DVD changer will stop while additional CD/DVDs are loaded. If the volume control is ON, the unit will switch from radio to CD/DVD mode and begin to play. The radio display will show the chapter number and index time in hours and minutes of the DVD, and the track number, minutes and second of the CD. Play will begin automatically in approximately 20 seconds.
UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions — Remote Control Power Button (PWR) Pressing the “POWER” button will turn the rear audio/ video system ON/OFF. The headphone symbol will flash for approximately 5 seconds in the radio display and sound can be heard from the headphones. NOTE: • The power button on the headphones must be turned ON before sound can be heard from the headphones. • When the rear audio/video system is ON, sound can only be heard from the front speakers.
UNDERSTANDING YOUR INSTRUMENT PANEL 173 MODE Button No Function Program Button (PROG) No Function SEEK Button Channel Button Press this button to select between channel “A” or channel “B”, or if interference is heard through the headphones. • CD/DVD changer Press the right side of the “SEEK” button for the next chapter or track on the disc. Press the left side to return to the beginning of the current chapter or track.
UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions — Video Screen Push up on the release button to lower the video screen. 2. Enter Button This button will enter the selection from the on-screen menu. 3. Brightness Button Changes the brightness of the screen picture. 1. Screen Width Button Changes the width of the screen picture.
UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions — Headphones 175 Power Button Pressing the power button will turn the headphones ON/OFF. NOTE: • The headphones will turn off automatically and the red LED will illuminate for approximately 2 minutes when the radio or rear audio/video system is turned off. • The rear audio/video system must be turned ON before sound can be heard from the headphones. 1. ON/OFF Button 2. Scan Button 3. Volume Control 4.
UNDERSTANDING YOUR INSTRUMENT PANEL Scan Button Pressing the scan button will automatically find the audio signal that is transmitted from the CD/DVD changer when the rear audio/video system and the headphones are on. This button is used only if the headphones are locked on to a source other than the vehicle’s radio. NOTE: When the “GREEN LED” is showing the headphones are receiving the audio signal.
UNDERSTANDING YOUR INSTRUMENT PANEL General Information This device complies with part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) This device must accept any interference received, including interference that may cause undesired operation.
UNDERSTANDING YOUR INSTRUMENT PANEL REMOTE SOUND SYSTEM CONTROLS The remote sound system controls are located on the rear surface of the steering wheel at the 3 and 9 o’clock positions. Radio Operation Pressing the top of the switch will SEEK up for the next listenable station and pressing the bottom of the switch will SEEK down for the next listenable station. The right hand rocker switch has a push button in the center and controls the volume and mode of the sound system.
UNDERSTANDING YOUR INSTRUMENT PANEL CD Player Pressing the top of the switch once will go to the next track on the CD. Pressing the bottom of the switch once will go to the beginning of the current track or to the beginning of the previous track if it is within one second after the current track begins to play. If you press the switch up or down twice it plays the second track, three times, it will play the third, etc. The button in the center of the left hand switch has no function in this mode.
UNDERSTANDING YOUR INSTRUMENT PANEL AM Reception AM sound is based on wave amplitude, so AM reception can be disrupted by such things as lightning, power lines and neon signs. FM Reception Because FM transmission is based on frequency variations, interference that consists of amplitude variations can be filtered out, leaving the reception relatively clear, which is the major feature of FM radio.
UNDERSTANDING YOUR INSTRUMENT PANEL Maintain your cassette tape player. The head and capstan shaft in the cassette player can pick up dirt or tape deposits each time a cassette is played. The result of deposits on the capstan shaft may cause the tape to wrap around and become lodged in the tape transport. The other adverse condition is low or “muddy” sound from one or both channels, as if the treble tone control were turned all the way down.
UNDERSTANDING YOUR INSTRUMENT PANEL RADIO OPERATION AND CELLULAR PHONES Under certain conditions, the cellular phone being On in your vehicle can cause erratic or noisy performance from your radio. This condition may be lessened or eliminated by relocating the cellular phone antenna. This condition is not harmful to the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL To replace the navigation map DVD lift the storage bin cover and liner in the rear cargo area, press the eject button and the disc will eject. Gently insert the new disc into the DVD unit with the label facing up. The disc will automatically be pulled into the DVD unit. 183 temperature, the airflow volume, the airflow distribution, and amount of inside air recirculation to maintain front seat occupant comfort, even under changing outside weather conditions.
UNDERSTANDING YOUR INSTRUMENT PANEL regulates the heating and air conditioning system including blower speed, outlet air temperature, and airflow distribution through the various outlets within the instrument panel. Using the 9TEMP9 buttons, adjust the temperature you would like the system to maintain. When the system is set to your comfort level, it is not necessary to change the settings. You will experience the greatest efficiency by allowing the system to function automatically.
UNDERSTANDING YOUR INSTRUMENT PANEL • The “DELAY” symbol will flash to indicate that the feature as been disabled. This feature may be enabled using the following procedure: • Press and hold the Heated Rear Window and Auto HI buttons for 5 seconds. • The “DELAY” symbol will flash to indicate that the feature as been enabled. Power Button This button turns the entire system ON/OFF. When the system is turned on it will return to the previous settings.
UNDERSTANDING YOUR INSTRUMENT PANEL The front blower control can be set to any fixed blower speed by pressing the rocker switch up or down. This allows the front occupants to control the volume of air circulated in the vehicle and cancel the auto mode. The fan will now operate at a fixed speed until additional speeds are selected or until either the 9AUTO HI9 or 9AUTO LO9 buttons are pressed. The system will continue to automatically adjust air temperature and airflow distribution.
UNDERSTANDING YOUR INSTRUMENT PANEL Bi-Level Mode 187 Floor Mode 4 Air comes from both the instrument panel outlets and floor outlets. A slight amount of air is also directed through the defrost and side window demister outlets. NOTE: In many temperature positions, the bi-level mode is designed to provide cooler air out of the panel outlets and warmer air from the floor outlets. Air comes from the floor outlets. A slight amount of air is directed through the defrost and side window demister outlets.
UNDERSTANDING YOUR INSTRUMENT PANEL Mix Mode Defrost Mode Air comes from the floor, defrost and side window demist outlets. This mode is not used when operating in either 9AUTO HI9 or 9AUTO LO9. This mode should be used when airflow to the floor and windshield is desired. Air comes from the windshield and side window demist outlets. Use this setting when necessary to defrost your windshield and side windows.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: While operating in 9AUTO HI9 or 9AUTO LO9, the system will not automatically sense the presence fog, mist, or ice on the windshield. The defrost button must be pressed to clear the windshield and side glass. Depress the “A/C” button to turn on and off the air conditioning during manual operation only. Cool dehumidified air comes through the outlets selected by the Mode Control. To turn off the air conditioning, press the A/C button a second time.
UNDERSTANDING YOUR INSTRUMENT PANEL A/C Recirculation Programming The recirculation control is programmed to cancel the recirculation mode when the ignition key is turned OFF and will reset to the outside air mode when the ignition key is turned “ON”. The frequent use of outside air will help keep odors from building up within the air conditioner-heater housing. It is recommended that the recirculation mode be used as little as possible, especially in humid climates.
UNDERSTANDING YOUR INSTRUMENT PANEL Rear Fan Operation To operate the rear fan, press the 9REAR9 button. The first time this button is pressed the 9REAR AUTO9 display will illuminate indicating that the rear fan speed is automatically controlled. To manually control the rear fan speed, press the 9REAR9 button again and only 9REAR9 will illuminate in the display. This allows the rear seat occupants to control the rear fan speed using the switch located in the center console between the second row seats.
UNDERSTANDING YOUR INSTRUMENT PANEL Use of the air Recirculation mode during winter months is not recommended because it may cause window fogging. Vacation Storage Anytime you store your vehicle, or keep it out of service (i.e. vacation) for two weeks or more, run the air conditioning system at idle for about five minutes in the fresh air and high blower setting. This will insure adequate system lubrication to minimize the possibility of compressor damage when the system is started again.
UNDERSTANDING YOUR INSTRUMENT PANEL Outside Temperature Display The outside temperature can be shown in the ATC display by pressing the 9OUTSIDE TEMP9 button. After pressing this button, the front seat passenger’s temperature setting display will be replaced with the current outside temperature. Press the 9OUTSIDE TEMP9 button again or press the passenger’s 9TEMP9 button to return the display to the passenger’s temperature setting.
STARTING AND OPERATING CONTENTS m Starting Procedures . . . . . . . . . . . . . . . . . . . . . 198 ▫ AutoStick Operation . . . . . . . . . . . . . . . . . . . 204 ▫ Normal Starting . . . . . . . . . . . . . . . . . . . . . . 198 ▫ AutoStick General Information . . . . . . . . . . . . 204 m Engine Block Heater — If Equipped . . . . . . . . . 200 m All Wheel Drive — If Equipped . . . . . . . . . . . . 205 m Automatic Transmission . . . . . . . . . . . . . . . . . . 201 m Parking Brake . . . . . . . .
STARTING AND OPERATING m Tire Safety Information . . . . . . . . . . . . . . . . . . . 213 m All Wheel Drive (AWD) — If Equipped . . . . . . . 230 ▫ Tire Markings . . . . . . . . . . . . . . . . . . . . . . . . 213 m Tire Pressure Monitor System — If Equipped . . . 230 ▫ Tire Identification Number (TIN) . . . . . . . . . . 217 ▫ 1,2,3, Or 4 Tire(s) Low Pressure . . . . . . . . . . . 231 ▫ Tire Loading And Tire Pressure . . . . . . . . . . . 218 ▫ 1,2,3, Or 4 Tire(s) High Pressure . . . . . . .
STARTING AND OPERATING 197 ▫ Gasoline/Oxygenate Blends . . . . . . . . . . . . . . 236 m Vehicle Loading . . . . . . . . . . . . . . . . . . . . . . . . 241 ▫ MMT In Gasoline . . . . . . . . . . . . . . . . . . . . . 237 ▫ Vehicle Certification Label . . . . . . . . . . . . . . . 241 ▫ Sulfur In Gasoline . . . . . . . . . . . . . . . . . . . . . 237 ▫ Gross Vehicle Weight Rating (GVWR) . . . . . . . 242 ▫ Materials Added To Fuel . . . . . . . . . . . . . . . .
STARTING AND OPERATING STARTING PROCEDURES CAUTION! Long periods of engine idling, especially at high engine speeds, can cause excessive exhaust temperatures which can damage your vehicle. Do not leave your vehicle unattended with the engine running. WARNING! Do not leave animals or children inside parked vehicles in hot weather; interior heat build up may cause serious injury or death. The gear selector must be in the NEUTRAL or PARK position before you can start the engine.
STARTING AND OPERATING WARNING! • Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transmission cannot be started this way. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle. If the vehicle has a discharged battery, booster cables may be used to obtain a start from a booster battery or the battery in another vehicle. This type of start can be dangerous if done improperly.
STARTING AND OPERATING If the engine has been flooded, it may start to run, but not have enough power to continue running when the key is released. If this occurs, continue cranking up to 15 seconds with the accelerator pedal pushed all the way to the floor. Release the accelerator pedal and the key once the engine is running smoothly. Do not overspeed engine.
STARTING AND OPERATING AUTOMATIC TRANSMISSION CAUTION! Damage to the transmission may occur if the following precautions are not observed: • Shift into PARK only after the vehicle has come to a complete stop. • Shift into or out of REVERSE only after the vehicle has come to a complete stop and the engine is at idle speed. • Do not shift from REVERSE, PARK, or NEUTRAL into any forward gear when the engine is above idle speed.
STARTING AND OPERATING Automatic Transmission Ignition Interlock System This system prevents the key from being removed unless the shift lever is in PARK. It also prevents shifting out of PARK unless the key is in the ACCESSORY or ON position. NOTE: If a malfunction occurs, the system will trap the key in the ignition cylinder to warn you that this safety feature is inoperable. The engine can be started and stopped but the key cannot be removed until you obtain service.
STARTING AND OPERATING NOTE: Even if the transmission can be reset, it is recommended that you visit a dealer at your earliest possible convenience. Your dealer has diagnostic equipment to determine if the problem could recur. If the transmission cannot be reset, dealer service is required. Gear Ranges DO NOT race the engine when shifting from PARK or NEUTRAL positions into another gear range. “P” Park Supplements the parking brake by locking the transmission. The engine can be started in this range.
STARTING AND OPERATING AUTOSTICK Autostick is a driver-interactive transmission that offers manual gear shifting capability to provide you with more control. Autostick allows you to maximize engine braking, eliminate undesirable upshifts and downshifts, and improve overall vehicle performance. This system can also provide you with more control during passing, city driving, cold slippery conditions, mountain driving, trailer towing, and many other situations.
STARTING AND OPERATING • You can start out in first, second, or third gear. Shifting into fourth gear can occur only after vehicle speed reaches 15 mph (24 km/h). • The transmission will automatically downshift to first gear when coming to a stop. • Starting out in third gear is helpful in snowy or icy conditions. • While in the Autostick mode, Speed Control will only function in third or fourth gear. Downshifting out of third gear will turn off the speed control.
STARTING AND OPERATING CAUTION! All wheels must have the same size and type tires. Unequal tire sizes must not be used. Unequal tire size may cause failure of the power transfer unit and/or the viscous coupling. PARKING BRAKE When the parking brake is applied with the ignition switch on, the brake light in the instrument cluster will turn on. NOTE: This light only shows that the parking brake is applied. It does not show the degree of brake application.
STARTING AND OPERATING When parking on a hill, it is important to set the parking brake before placing the gear selector in Park, otherwise the load on the transmission locking mechanism may make it difficult to move the selector out of park. As an added precaution, turn the front wheels toward the curb on a downhill grade and away from the curb on a uphill grade. The parking brake should always be applied when the driver is not in the vehicle.
STARTING AND OPERATING BRAKE SYSTEM In the event power assist is lost for any reason (for example, repeated brake applications with the engine off), the brakes will still function. The effort required to brake the vehicle will be much greater than that required with the power system operating. Your vehicle is equipped with dual hydraulic brake systems. If either of the two hydraulic systems lose normal capability, the remaining system will still function.
STARTING AND OPERATING WARNING! • Anti-lock system (ABS) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded. • The ABS cannot prevent accidents, including those resulting from excessive speed in turns, following another vehicle too closely, or hydroplaning. Only a safe, attentive, and skillful driver can prevent accidents.
STARTING AND OPERATING When the vehicle is driven over 7 mph (11 km/h), you may also hear a slight clicking sound as well as some related motor noises. These noises are the system performing its self check cycle to ensure that the ABS system is working properly. This self check occurs each time the vehicle is started and accelerated past 7 mph (11 km/h). ABS is activated during braking under certain road or stopping conditions.
STARTING AND OPERATING POWER STEERING The standard power steering system will give you good vehicle response and increased ease of maneuverability in tight spaces. The system will provide mechanical steering capability if power assist is lost. If for some reason, the power assist is interrupted, it will still be possible to steer your vehicle. Under these conditions you will observe a substantial increase in steering effort, especially at very low vehicle speeds and during parking maneuvers.
STARTING AND OPERATING TRACTION CONTROL — IF EQUIPPED The Traction Control System reduces wheel slip and maintains traction at the driving (front) wheels. The system reduces wheel slip by engaging the brake on the wheel that is losing traction (spinning). The system will operate at speeds below 35 mph (56 km/h).
STARTING AND OPERATING NOTE: • The Traction Control system will make buzzing or clicking sounds when in operation. 213 TIRE SAFETY INFORMATION Tire Markings • Extended heavy use of Traction Control may cause the system to deactivate and turn on the traction control indicator located in the instrument cluster. This is to prevent overheating of the brake system and is a normal condition. The system will remain disabled for about 4 minutes until the brakes have cooled.
STARTING AND OPERATING • European Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter 9P9 is absent from this tire size designation. Example: 215/65R15 96H • Temporary Spare tires are high pressure compact spares designed for temporary emergency use only. Tires designed to this standard have the letter “T” molded into the sidewall preceding the size designation.
STARTING AND OPERATING 215 Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards (....blank....( = Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary Spare tire 31 = Overall Diameter in Inches (in) 215 = Section Width in Milimeters (mm) 65 = Aspect Ratio in Percent (%) —Ratio of section height to section width of tire. 10.
STARTING AND OPERATING EXAMPLE: Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry. H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions. —The maximum speed corresponding to the Speed Symbol should only be achieved under specified operating conditions. (ie. tire pressure, vehicle loading, road conditions and posted speed limits).
STARTING AND OPERATING Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire however the date code may only be on one side. Tires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire. 217 Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the outboard side then you will find it on the inboard side of the tire.
STARTING AND OPERATING Tire Loading and Tire Pressure Tire and Loading Information Placard Tire Placard Location NOTE: Some vehicles have a “Tire and Loading Information” placard located on the driver’s side “B” pillar. This placard tells you important information about the, 1) number of people that can be carried in the vehicle 2) the total weight your vehicle can carry 3) the tire size designed for your vehicle 4) the cold tire inflation pressures for the front, rear and spare tires.
STARTING AND OPERATING Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size and cold tire inflation pressures specified on the Tire and Loading Information placard and the Vehicle Loading section of this manual.
STARTING AND OPERATING 4. The resulting figure equals the available amount of cargo and luggage load capacity. For example, if “XXX” amount equals 1400 lbs. and there will be five 150 lb. passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lb. (1400–750 (5 x 150) = 650 lb.) 5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in step 4. 6.
STARTING AND OPERATING 221 5
STARTING AND OPERATING WARNING! Overloading of your tire is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle-never overload them. 1. Safety— WARNING! Improperly inflated tires are dangerous and can cause accidents. • Under inflation increases tire flexing and can result in tire failure. • Over inflation reduces a tire’s ability to cushion TIRES—GENERAL INFORMATION shock.
STARTING AND OPERATING 2. Economy— Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Underinflation also increases tire rolling resistance and results in higher fuel consumption. 223 Some vehicles may have Supplemental Tire Pressure Information for vehicle loads that are less that the maximum loaded vehicle condition.
STARTING AND OPERATING The pressure should be checked and adjusted as well as inspecting for signs of tire wear or visible damage at least once a month. Use a good quality pocket-type gauge to check tire pressure. Do not make a visual judgement when determining proper inflation. Radial tires may look properly inflated even when they are underinflated. CAUTION! After inspecting or adjusting the tire pressure always reinstall the valve stem cap–if equipped.
STARTING AND OPERATING Tire pressure may increase from 2 to 6 psi (13 to 40 kPa) during operation. DO NOT reduce this normal pressure build up or your tire pressure will be too low. Tire Pressures for High Speed Operation The manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or conditions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressure is very important.
STARTING AND OPERATING Radial-Ply Tires WARNING! Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly. The instability could cause an accident. Always use radial ply tires in sets of four (or 6, in case of trucks with dual rear wheels). Never combine them with other types of tires. Cuts and punctures in radial tires are repairable only in the tread area because of sidewall flexing. Consult your authorized tire dealer for radial tire repairs.
STARTING AND OPERATING Do not install a wheel cover or attempt to mount a conventional tire on the compact spare wheel, since the wheel is designed specifically for the compact spare. 227 See the paragraph on Freeing A Stuck Vehicle in Section 6 of this manual. WARNING! CAUTION! Because of the reduced ground clearance, do not take your vehicle through an automatic car wash with the compact spare installed. Damage to the vehicle may result.
STARTING AND OPERATING Tread Wear Indicators Tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced. These indicators are molded into the bottom of the tread grooves and will appear as bands when the tread depth becomes 1/16 inch (2 mm). When the indicators appear in 2 or more adjacent grooves, the tire should be replaced. Many states have laws requiring tire replacement at this point.
STARTING AND OPERATING 229 WARNING! CAUTION! • Do not use a tire, wheel size or rating other than that Replacing original tires with tires of a different size may result in false speedometer and odometer readings. specified for your vehicle. Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle.
STARTING AND OPERATING Improper alignment will not cause vehicle vibration. Vibration may be a result of tire and wheel out-ofbalance. Proper balancing will reduce vibration and avoid tire cupping and spotty wear. ALL WHEEL DRIVE (AWD) — IF EQUIPPED CAUTION! All Wheel Drive (AWD) vehicles must have the same size and type tires on all wheel positions. Unequal tire sizes must not be used. Unequal tire size may cause failure of the power transfer unit and/or the viscous coupling.
STARTING AND OPERATING 1,2,3, OR 4 TIRE(S) LOW PRESSURE Low tire pressure levels of 25 psi [1.72 bars] (172 kPa) or less detected in one or more tires. Inspect all tires for proper inflation pressure, once the proper tire pressure has been set, the TPM system warning will reset automatically when the vehicle has been driven for at least 2 minutes at or above 20 mph (32 km/h). 1,2,3, OR 4 TIRE(S) HIGH PRESSURE High tire pressure levels of 45 psi [3.10 bars] (310 kPa) or more detected in one or more tires.
STARTING AND OPERATING CAUTION! The TPM system has been optimized for the original equipment tires and wheels. TPM system pressures have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equipment that is not of the same size, type, and/or style. After-market wheels can cause sensor damage.
STARTING AND OPERATING General Information This device complies with part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired operation. The tire pressure sensors are covered under one of the following licenses: United States . . . . . . . . . . . . . . . . . . . . . KR5S120123 Canada . . . . . . . . . . . .
STARTING AND OPERATING NOTE: In order to avoid damage to tires, chains, and your vehicle do not drive for a prolonged period of time on dry pavement. Observe the tire chain manufacturer’s instructions on method of installation, operating speed, and conditions for usage. Always use the lower suggested operating speed if both the chain manufacturer and vehicle manufacture suggest a maximum speed. This notice applies to all chain traction devices, including link and cable (radial) chains.
STARTING AND OPERATING Section of this manual. More frequent rotation is permissible if desired. The reasons for any rapid or unusual wear should be corrected prior to rotation being performed. NOTE: The Tire Pressure Monitor system must be retrained following a tire rotation. See your authorized dealer for service. The suggested rotation method is the “forward-cross” shown in the following diagram.
STARTING AND OPERATING Over 40 automobile manufacturers around the world have issued and endorsed consistent gasoline specifications (the World Wide Fuel Charter, WWFC) to define fuel properties necessary to deliver enhanced emissions, engine performance, and durability for your vehicle. The manufacturer recommends the use of gasolines that meet the WWFC specifications if they are available.
STARTING AND OPERATING may not be covered by the vehicle warranty. While MTBE is an oxygenate made from Methanol, it does not have the negative effects of Methanol. MMT In Gasoline MMT is a manganese containing metallic additive that is blended into some gasoline to increase the octane number. Gasolines blended with MMT offer no performance advantage beyond gasolines of the same octane number without MMT.
STARTING AND OPERATING CAUTION! If the Malfunction Indicator light is flashing, immediate service is required. Refer to the paragraph on the Onboard Diagnostics System in section 7 of this manual. Materials Added to Fuel All gasoline sold in the United States is required to contain effective detergent additives. Use of additional detergents or other additives are not needed under normal conditions and would result in additional cost. Therefore you should not have to add anything to the fuel.
STARTING AND OPERATING • The use of fuel additives which are now being sold as octane enhancers are not recommended. Most of these products contain high concentrations of methanol. Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives are not the responsibility of the manufacturer and may not be covered under the New Vehicle Warranty. NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you.
STARTING AND OPERATING ADDING FUEL CAUTION! Fuel Filler Cap (Gas Cap) The gas cap is located behind the fuel filler door on the left side of the vehicle. If the gas cap is lost or damaged, be sure the replacement cap is for use with this vehicle. CAUTION! Damage to the fuel system or emission control system could result from using an improper fuel tank filler tube cap (gas cap). A poorly fitting cap could let impurities into the fuel system.
STARTING AND OPERATING WARNING! • Remove the fuel tank filler tube cap (gas cap) slowly to prevent fuel spray from the filler neck which may cause injury. • The volatility of some gasolines may cause a buildup of pressure in the fuel tank that may increase while you drive. This pressure can result in a spray of gasoline and/or vapors when the cap is removed from a hot vehicle. Removing the cap slowly allows the pressure to vent and prevents fuel spray.
STARTING AND OPERATING • Vehicle Identification Number (VIN) • Type of Vehicle • Month Day and Hour of Manufacture (MDH) The bar code allows a computer scanner to read the Vehicle Identification Number (VIN). Gross Vehicle Weight Rating (GVWR) The GVWR is the total allowable weight of your vehicle. This includes driver, passengers, and cargo. The total load must be limited so that you do not exceed the GVWR. Gross Axle Weight Rating (GAWR) The GAWR is the maximum capacity of the front and rear axles.
STARTING AND OPERATING Figure out the weight on the front and rear of the vehicle separately. It is important that you distribute the load evenly over the front and rear axles. 243 A loaded vehicle is shown in the illustration. Note that neither the GVWR or the GAWR capacities have been exceeded. Overloading can cause potential safety hazards and shorten useful service life. Heavier axles or suspension components do not necessarily increase the vehicle’s GVWR.
STARTING AND OPERATING Front Rear Axle Axle Empty Weight 2538 lbs 2076 lbs (1151 kg) (942 kg ) Load (Including driver, pass223 lbs 890 lbs sengers and cargo) (101 kg) (404 kg) Total 2762 lbs 2968 lbs (1253 kg) (1346 kg) GAWR 2826 lbs 3035 lbs (1282 kg) (1377 kg) TRAILER TOWING In this section you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle.
STARTING AND OPERATING 245 Warranty Requirements The Manufacturer’s Passenger Vehicle Warranty will apply to vehicles used to tow trailers for non-commercial use. However the following conditions must be met: NOTE: Using the “3” range while operating the vehicle under heavy operating conditions will improve performance and extend transmission life by reducing excessive shifting and heat build up. • The maximum frontal area of the trailer cannot exceed 20 square feet (1.86 square meters).
STARTING AND OPERATING • The automatic transmission fluid and filter should be changed if you REGULARLY tow a trailer for more than 45 minutes of continuous operation. See Schedule “B” in section 8 of this manual for transmission fluid change intervals. speed may be required to avoid extended driving at high RPM. Return to a higher gear range or vehicle speed when road conditions and RPM level allows. TRAVEL CONDITION NOTE: • Check the automatic transmission fluid level before towing.
STARTING AND OPERATING A load equalizing hitch is recommended for loaded trailer weights above 1,000 lbs (454 kg) and required for weights above 2,000 lbs (907 kg). CAUTION! If the trailer weighs more than 1,000 lbs (454 kg) loaded, it should have its own brakes and they should be of adequate capacity. Failure to do this could lead to accelerated brake lining wear, higher brake pedal effort, and longer stopping distances.
WHAT TO DO IN EMERGENCIES CONTENTS m Hazard Warning Flasher . . . . . . . . . . . . . . . . . . 250 ▫ Acceleration . . . . . . . . . . . . . . . . . . . . . . . . . 259 m If Your Engine Overheats . . . . . . . . . . . . . . . . . 251 ▫ Traction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260 m Jacking And Tire Changing . . . . . . . . . . . . . . . . 252 m Freeing A Stuck Vehicle . . . . . . . . . . . . . . . . . . 260 ▫ Jack Location . . . . . . . . . . . . . . . . . . . . . . . .
WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER The hazard flasher switch is located in the center of the instrument panel above the center air outlets. To engage the Hazard Warning Flashers, depress the switch on the instrument panel. When the Hazard Warning Switch is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency. Push the switch a second time to turn off the flashers.
WHAT TO DO IN EMERGENCIES IF YOUR ENGINE OVERHEATS In any of the following situations, you can reduce the potential for overheating by taking the appropriate action. • On the highways — Slow down. • In city traffic — While stopped, put transmission in neutral, but do not increase engine idle speed. NOTE: There are steps that you can take to slow down an impending overheat condition. If your air conditioner is on, turn it off.
WHAT TO DO IN EMERGENCIES WARNING! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call a service center if your vehicle overheats. If you decide to look under the hood yourself, see Section 7, Maintenance, of this manual. Follow the warnings under the Cooling System Pressure Cap paragraph. JACKING AND TIRE CHANGING WARNING! • Getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you.
WHAT TO DO IN EMERGENCIES Jack Location The jack and jack-handle are stowed in the rear storage bin located in the rear cargo floor. Pull up on the storage bin cover and liner to access the jack and jack tools. 253 Spare Tire Stowage The spare tire is stowed under the rear of the vehicle by means of a cable winch mechanism. To remove or stow the spare, use the jack handle to rotate the “spare tire drive” nut.
WHAT TO DO IN EMERGENCIES Spare Tire Removal Fit the jack-handle over the drive nut. Rotate the nut to the left until the spare is on the ground with enough slack cable to allow you to pull the tire out from under the vehicle. Preparations For Jacking Park the vehicle on a firm level surface, avoid ice or slippery areas, set the parking brake and place the gear selector in PARK. Turn OFF the ignition. WARNING! CAUTION! The winch mechanism is designed for use with the jack handle only.
WHAT TO DO IN EMERGENCIES 255 • Passengers should not remain in the vehicle when the vehicle is being jacked. Jacking Instructions 1. Remove the spare wheel, scissors jack and jack-handle from stowage. 2. Carefully pry off the wheel center cap using the tip of the jack handle. 3. Loosen (but do not remove) the wheel lug nuts by turning them to the left one turn while the wheel is still on the ground. 4. There are two jack engagement locations on each side of the body — see illustration. 6 5.
WHAT TO DO IN EMERGENCIES location. Do not raise the vehicle until you are sure the jack is securely engaged. Never jack up the vehicle using any suspension components. 6. Raise the vehicle by turning the jack screw to the right, using the swivel wrench. Raise the vehicle only until the tire just clears the surface and enough clearance is obtained to install the spare tire. Minimum tire lift provides maximum stability.
WHAT TO DO IN EMERGENCIES WARNING! A loose tire or jack, thrown forward in a collision or hard stop could endanger the occupants of the vehicle. Always stow the jack parts and the spare tire in the places provided. 12. Secure the flat or spare tire as follows: • The center cap of a cast aluminum wheel must be removed prior to flat tire stowage. Store the center cap inside the glove box or other storage compartment. • Turn the wheel so that the valve-stem is down.
WHAT TO DO IN EMERGENCIES JUMP-STARTING PROCEDURES IF BATTERY IS LOW WARNING! • Do not attempt to push or tow your vehicle to get it WARNING! Take care to avoid the radiator cooling fan whenever the hood is raised. It can start anytime the ignition switch is on. You can be hurt by the fan. started. Vehicles equipped with an automatic transmission cannot be started this way.
WHAT TO DO IN EMERGENCIES 1. Wear eye protection and remove any metal jewelry such as watch bands or bracelets that might make an inadvertent electrical contact. 2. When boost is provided by a battery in another vehicle, park that vehicle within booster cable reach and without letting the vehicles touch. Set the parking brake, place the automatic transmission in PARK and turn the ignition switch to the OFF position for both vehicles. 3. Turn off the heater, radio and all unnecessary electrical loads. 4.
WHAT TO DO IN EMERGENCIES WARNING! Rapid acceleration on slippery surfaces is dangerous. Unequal traction can cause sudden pulling of the front wheels. You could lose control of the vehicle and possibly have an accident. Accelerate slowly and carefully whenever there is likely to be poor traction (ice, snow, wet mud, loose sand, etc.). Traction When driving on wet or slushy roads, it is possible for a wedge of water to build up between the tire and road surface.
WHAT TO DO IN EMERGENCIES WARNING! Fast spinning tires can be dangerous. Forces generated by excessive wheel speeds may cause tire damage or failure. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 35 mph (55 km/h) when you are stuck. And don’t let anyone near a spinning wheel, no matter what the speed. CAUTION! Racing the engine or spinning the wheels too fast may lead to transmission overheating and failure. It can also damage the tires.
WHAT TO DO IN EMERGENCIES All Wheel Drive Your vehicle may be towed under the following conditions: The gear selector must be in NEUTRAL, the distance to be traveled must not exceed 100 miles (160 km), the towing speed must not exceed 44 mph (72 km/h), and both front and rear wheels must be on the ground. If your vehicle must be towed farther or at a higher rate of speed, it must be transported on a flat bed truck.
WHAT TO DO IN EMERGENCIES If it is necessary to use the accessories while being towed (wipers, defrosters, etc.), the key must be in the ON position, not the ACCESSORY position. Make certain the transmission remains in NEUTRAL. Without The Ignition Key Special care must be taken when the vehicle is towed with the ignition in the LOCK position. The only approved method of towing with out the ignition key is with a flat bed truck. Proper towing equipment is necessary to prevent damage to the vehicle.
MAINTAINING YOUR VEHICLE CONTENTS m 3.5L Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . 268 ▫ Drive Belts — Check Condition And Tension . . 276 m Onboard Diagnostic System — OBD II . . . . . . . . 269 ▫ Spark Plugs . . . . . . . . . . . . . . . . . . . . . . . . . 277 m Emissions Inspection And Maintenance Programs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 270 ▫ Engine Air Cleaner Filter . . . . . . . . . . . . . . . . 277 m Replacement Parts . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE ▫ Steering Shaft Seal . . . . . . . . . . . . . . . . . . . . 283 ▫ Automatic Transmission . . . . . . . . . . . . . . . . 295 ▫ Steering Linkage . . . . . . . . . . . . . . . . . . . . . . 283 ▫ All Wheel Drive (AWD) — If Equipped . . . . . 298 ▫ Drive Shaft Universal Joints . . . . . . . . . . . . . . 283 ▫ Front And Rear Wheel Bearings . . . . . . . . . . . 300 ▫ Body Lubrication . . . . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE ▫ Front Park/Turn Signal And Sidemarker Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 309 ▫ Front Fog Light . . . . . . . . . . . . . . . . . . . . . . 309 ▫ Rear Tail, Stop, Turn Signal, Side Marker And Back-Up Lights . . . . . . . . . . . . . . . . . . . . . . . 310 ▫ License Light . . . . . . . . . . . . . . . . . . . . . . . . 311 267 m Fluid Capacities . . . . . . . . . . . . . . . . . . . . . . . . 311 m Recommended Fluids, Lubricants And Genuine Parts .
MAINTAINING YOUR VEHICLE 3.
MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
MAINTAINING YOUR VEHICLE EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle’s emissions control system. Failure to pass could prevent vehicle registration. For states which have an I/M (Inspection and Maintenance) requirement, this check verifies the following: the MIL (Malfunction Indicator Lamp) is functioning and is not on when the engine is running, and that the OBD (On Board Diagnostic) system is ready for testing.
MAINTAINING YOUR VEHICLE a. The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition key or start the engine. This means that your vehicle’s OBD system is not ready and you should not proceed to the I/M station. b. The MIL will not flash at all and will remain fully illuminated until you turn off the ignition key or start the engine. This means that your vehicle’s OBD system is ready and you can proceed to the I/M station.
MAINTAINING YOUR VEHICLE NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you. MAINTENANCE PROCEDURES The pages that follow contain the required maintenance services determined by the engineers who designed your vehicle. WARNING! Besides the maintenance items for which there are fixed maintenance intervals, there are other items that should operate satisfactorily without periodic maintenance.
MAINTAINING YOUR VEHICLE 273 The best time to check the engine oil level is about 5 minutes after a fully warmed engine is shut off or before starting the engine after it has sat overnight. Checking the oil while the vehicle is on level ground will improve the accuracy of the oil level readings. Maintain the oil level between the MIN and MAX markings on the dipstick. Adding one quart of oil when the reading is at the MIN mark will result in a MAX reading on these engines.
MAINTAINING YOUR VEHICLE Change Engine Oil Road conditions and your kind of driving affects the interval at which your oil should be changed. Check the following list to see if any apply to you. NOTE: If ANY of these apply to you then change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first and follow schedule “B” of the 9Maintenance Schedules9 section of this manual. • Day or night temperatures are below 32°F (0°C).
MAINTAINING YOUR VEHICLE American Petroleum Institute (API) Engine Oil Identification Symbol This symbol means that the oil has been certified by the American Petroleum Institute (API). The manufacture only recommends API Certified engine oils that meet the requirements of DaimlerChrysler Material Standard MS-6395. Use Mopar or an equivalent oil meeting the specification MS-6395.
MAINTAINING YOUR VEHICLE Synthetic Engine Oils You may use synthetic engine oils provided that the recommended oil quality requirements are met and the recommended maintenance intervals for oil and filter changes are followed. Materials Added to Engine Oil The manufacture strongly recommends against the addition of any additives (other than leak detection dyes) to the engine oil. Engine oil is an engineered product and it’s performance may be impaired by supplemental additives.
MAINTAINING YOUR VEHICLE Also check belt routing to make sure there is no interference between the belts and other engine components. Spark Plugs Spark plugs must fire properly to assure engine performance and emission control. New plugs should be installed at the specified mileage. The entire set should be replaced if there is any malfunction due to a faulty spark plug. Malfunctioning spark plugs can damage the catalytic converter.
MAINTAINING YOUR VEHICLE Catalytic Converter The catalytic converter requires the use of unleaded fuel only. Leaded gasoline will destroy the effectiveness of the catalyst as an emission control device. Under normal operating conditions, the catalytic converter will not require maintenance. However, it is important to keep the engine properly tuned to assure proper catalyst operation and prevent possible catalyst damage.
MAINTAINING YOUR VEHICLE WARNING! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your exhaust system. Do not park or operate your vehicle in areas where your exhaust system can contact anything that can burn. In unusual situations involving grossly malfunctioning engine operation, a scorching odor may indicate severe and abnormal catalyst overheating.
MAINTAINING YOUR VEHICLE WARNING! CAUTION! • Battery fluid is a corrosive acid solution and can burn or even blind you. Don’t allow battery fluid to contact your eyes, skin or clothing. Don’t lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area immediately with large amounts of water. • Battery gas is flammable and explosive. Keep flame or sparks away from the battery.
MAINTAINING YOUR VEHICLE Air Conditioner For best possible performance, your air conditioner should be checked and serviced by an Authorized Dealer at the start of each warm season. This service should include cleaning of the condenser fins and a system performance check. Drive belt tension should also be checked at this time. 281 WARNING! • Use only refrigerants approved by the manufacture for your air conditioning system. Some unapproved refrigerants are flammable and can explode, injuring you.
MAINTAINING YOUR VEHICLE Refrigerant Recovery And Recycling The air conditioning system of your vehicle contains R-134a, a refrigerant that does not deplete the ozone layer in the upper atmosphere. The manufacture recommends that air conditioning service be done by facilities using refrigerant recycling and recovery equipment that meets SAE standard J1991. A/C Air Filter The filter access door is located under the instrument panel on the passenger side.
MAINTAINING YOUR VEHICLE WARNING! Fluid level should be checked on a level surface and with the engine off to prevent injury from moving parts and to insure accurate fluid level reading. Do not overfill. Use only manufacturers recommended power steering fluid. If necessary, add fluid to restore to the proper indicated level. With a clean cloth, wipe any spilled fluid from all surfaces. Refer to Recommended Fluids, Lubricants, and Genuine Parts for correct fluid type.
MAINTAINING YOUR VEHICLE Continued operation could result in failure of the universal joint due to water and dirt contamination of the grease. This would require complete replacement of the joint assembly. The external lock cylinders should be lubricated twice a year, preferably in the fall and spring. Apply a small amount of a high quality lubricant such as Mopart Lock Cylinder Lubricant directly into the lock cylinder.
MAINTAINING YOUR VEHICLE 285 Windshield and Rear Window Washers The fluid reservoir for the windshield washers and the rear window washer is shared. It is located in the engine compartment and should be checked for fluid level at regular intervals. Fill the reservoir with windshield washer solvent (not radiator antifreeze) and operate the system for a few seconds to flush out the residual water. The washer fluid reservoir will hold a full gallon of fluid when the Low Washer Fluid Light illuminates.
MAINTAINING YOUR VEHICLE Whenever a change is noticed in the sound of the exhaust system, when exhaust fumes can be detected inside the vehicle, or when the underside or rear of the vehicle is damaged, have a competent mechanic inspect the complete exhaust system and adjacent body areas for broken, damaged, deteriorated, or mispositioned parts. Open seams or loose connections could permit exhaust fumes to seep into the passenger compartment.
MAINTAINING YOUR VEHICLE Coolant Checks Coolant protection checks should be made every 12 months (prior to the onset of freezing weather, where applicable). If coolant is dirty or rusty in appearance, the system should be drained, flushed and refilled with fresh coolant. Check the front of the A/C condenser for any accumulation of bugs, leaves, etc. If dirty, clean by gently spraying water from a garden hose vertically down the face of the condenser.
MAINTAINING YOUR VEHICLE CAUTION! • Mixing of coolants other than the specified HOAT coolant may result in decreased corrosion protection and engine damage that may not be covered under the new vehicle warranty. If a non-HOAT coolant is introduced into the cooling system in an emergency, it should be replaced with the specified coolant as soon as possible. • Do not use plain water alone or alcohol base antifreeze products.
MAINTAINING YOUR VEHICLE Coolant Pressure Cap The coolant pressure cap must be fully tightened to prevent loss of coolant, and to insure that coolant will return to the coolant bottle from the overflow tank. The coolant pressure cap should be inspected and cleaned if there is any accumulation of foreign material on the sealing surfaces. 289 WARNING! • The warning words “DO NOT OPEN HOT” on the coolant pressure cap are a safety precaution.
MAINTAINING YOUR VEHICLE Disposal of Used Engine Coolant Used ethylene glycol based engine coolant is a regulated substance requiring proper disposal. Check with your local authorities to determine the disposal rules for your community. To prevent ingestion by animals or children do not store ethylene glycol based engine coolant in open containers or allow it to remain in puddles on the ground. If ingested by a child, contact a physician immediately. Clean up any ground spills immediately.
MAINTAINING YOUR VEHICLE • If frequent coolant additions are required, the cooling system should be pressure tested for leaks. • Maintain coolant concentration at 50% ethylene glycol antifreeze (minimum) in water for proper corrosion protection of your engine which contains aluminum components. • Make sure that the radiator and coolant bottle hoses are not kinked or obstructed. • Keep the front of the radiator and the front of the A/C condenser clean.
MAINTAINING YOUR VEHICLE Brakes In order to assure brake system performance, all brake system components should be inspected periodically. Suggested service intervals can be found in the Maintenance Schedules. WARNING! Riding the brakes can lead to brake failure and possibly an accident. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage.
MAINTAINING YOUR VEHICLE 293 NOTE: Inspection of brake hoses should be performed whenever the brake system is serviced and at every engine oil change. Inspect hydraulic brake hoses for surface cracking, scuffing, or worn spots. If there is any evidence of cracking, scuffing, or worn spots, the hose should be replaced immediately! Eventual deterioration of the hose can take place resulting in a possibility of a burst failure.
MAINTAINING YOUR VEHICLE Use only manufacturers recommended brake fluid, refer to Recommended Fluids, Lubricants and Genuine Parts for correct fluid type. Use only brake fluid that has been in a tightly closed container to avoid contamination from foreign matter or moisture. WARNING! CAUTION! Overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts and the brake fluid catching fire.
MAINTAINING YOUR VEHICLE You are urged to use only the manufacture specified hoses with quick connect fittings, or their equivalent in material and specification, in any fuel system servicing. It is mandatory to replace any damaged hoses or quick connect fittings that have been removed during service. Care should be taken in installing quick connect fittings to insure they are properly installed and fully connected. See your authorized dealer for service.
MAINTAINING YOUR VEHICLE CAUTION! Using a transmission fluid other than the manufacturers recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder. Using a transmission fluid other than the manufacturers recommended fluid will result in more frequent fluid and filter changes. Refer to Recommended Fluids, Lubricants and Genuine Parts for correct fluid type.
MAINTAINING YOUR VEHICLE 5. Remove the dipstick and determine if the fluid is hot or warm. Hot fluid is approximately 180°F (82°C), which is the normal operating temperature after the vehicle has been driven at least 15 miles (24 km). The fluid cannot be comfortably held between the finger tips. Cold is when the fluid is below 80°F (27°C). 6. Wipe the dipstick clean and reinsert until seated. Remove dipstick and note reading. 297 CAUTION! Do not overfill.
MAINTAINING YOUR VEHICLE • Police, taxi, limousine, commercial type operation, or trailer towing where the vehicle driven regularly for more than 45 minutes of continuous operation. NOTE: Refer to Section 8 of this manual for Maintenance Schedules. If the transmission is disassembled for any reason, the fluid and filter should be changed. Special Additives Do not add any fluid additives to the transmission. The only exception to this policy is the use of special dyes to aid in detecting fluid leaks.
MAINTAINING YOUR VEHICLE Overrunning Clutch The fill plug is located on the side of the overrunning clutch housing. The fluid should be maintained at a level even with the bottom of the fill plug hole when the vehicle is parked on a level surface. If it becomes necessary to add or replace the fluid, use only the manufacturers recommended transmission fluid, refer to Recommended Fluids, Lubricants and Genuine Parts for correct fluid type.
MAINTAINING YOUR VEHICLE Front And Rear Wheel Bearings Front and rear wheel bearings are permanently sealed. No regular maintenance is required for these components. Appearance Care and Protection from Corrosion Protection of Body and Paint from Corrosion Vehicle body care requirements vary according to geographic locations and usage.
MAINTAINING YOUR VEHICLE Washing • Wash your vehicle regularly. Always wash your vehicle in the shade using a mild car wash soap, and rinse the panels completely with clear water. • If insects, tar or other similar deposits have accumulated on your vehicle, wash it as soon as possible. • Use Mopar auto polish to remove road film and stains and to polish your vehicle. Take care never to scratch the paint.
MAINTAINING YOUR VEHICLE • If your vehicle is damaged due to an accident or similar cause which destroys the paint and protective coating have your vehicle repaired as soon as possible. The cost of such repairs is considered the responsibility of the owner. • All wheels and wheel trim, especially aluminum and chrome plated wheels should be cleaned regularly with mild soap and water to prevent corrosion. To remove heavy soil, select a nonabrasive, non-acidic cleaner.
MAINTAINING YOUR VEHICLE 303 Your leather upholstery can be best preserved by regular cleaning with a damp soft cloth. Small particles of dirt can act as an abrasive and damage the leather upholstery and should be removed promptly with a damp cloth. Stubborn soils can be removed easily with a soft cloth and Mopar Total Clean. Care should be taken to avoid soaking your leather upholstery with any liquid.
MAINTAINING YOUR VEHICLE 1. Clean with a wet soft rag. A mild soap solution may be used, but do not use high alcohol content or abrasive cleaners. If soap is used, wipe clean with a clean damp rag. 2. Dry with a soft tissue. Seat Belt Maintenance Do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage can also weaken the fabric. If the belts need cleaning, use a mild soap solution or lukewarm water.
MAINTAINING YOUR VEHICLE INTEGRATED POWER MODULE (IPM) An Integrated Power Module is located in the engine compartment near the battery. This center contains fuses and relays. A label that identifies each component is printed on the inside of the cover. 305 CAUTION! • When installing the Integrated Power Module cover, it is important to ensure the cover is properly positioned and fully latched.
MAINTAINING YOUR VEHICLE VEHICLE STORAGE If you are leaving your vehicle dormant for more than 21 days you may want to take steps to protect your battery. You may: • Disconnect the negative cable from the battery. • Anytime you store your vehicle, or keep it out of service (i.e. vacation) for two weeks or more, run the air conditioning system at idle for about five minutes in the fresh air and high blower setting.
MAINTAINING YOUR VEHICLE 307 LIGHT BULBS — Exterior Bulb Number Back-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 921 Rear Stop, Turn Signal . . . . . . . . . . . . . . . . . . . . 3157 Rear Sidemarker . . . . . . . . . . . . . . . . . . . . . . . . . 168 Fog Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 880L Front Turn Signal. . . . . . . . . . . . . . . . . . . . . . . . 3157 Front Sidemarker. . . . . . . . . . . . . . . . . . . . . . . . . 194 Headlight . . . . . .
MAINTAINING YOUR VEHICLE CAUTION! WARNING! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with an oily surface, clean the bulb with rubbing alcohol. A transient high tension occurs at the bulb sockets of High Intensity Discharge (HID) headlights when the headlight switch is turned ON. It may cause serious electrical shock or electrocution if not serviced properly. See your authorized dealer for service.
MAINTAINING YOUR VEHICLE Front Park/Turn Signal and Sidemarker Lights 1. Remove the two screws securing the headlight module to the vehicle and pull the headlight module forward away from the vehicle. 309 2. Twist the bulb socket to remove from the headlight module and pull the bulb from socket. 3. Replace the bulb, reinstall the socket and then reinstall the headlight module. Front Fog Light 1. Remove the screw from the front of the fog light and pull out from the front of the fascia. 2.
MAINTAINING YOUR VEHICLE CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with an oily surface, clean the bulb with rubbing alcohol. Rear Tail, Stop, Turn Signal, Side Marker and Back-up Lights 1. Raise the liftgate. 2. Remove the two tail light assembly screws and rotate the assembly outward to remove the ball stud form the attaching grommet. 3. Squeeze the socket assembly tabs to remove it from the housing. 4.
MAINTAINING YOUR VEHICLE License Light 1. Place a screwdriver in the slot next to the release tab and push on the release tab to remove the lens. 2. Unscrew the bulb and remove it from the socket. Replace the bulb and push on the lens until it snaps into place. 311 FLUID CAPACITIES U.S. Metric Fuel (approximate) 23 gallons 87 liters Engine Oil-With Filter 3.5 Liter Engines 5.5 qts 5.2 liters Cooling System * 3.5 Liter Engines 10.5 qts 9.
MAINTAINING YOUR VEHICLE RECOMMENDED FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant Engine Oil Spark Plugs Oil Filter Fuel Selection Fluids, Lubricants and Genuine Parts Mopart Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) Use API Certified, meeting material standard MS-6395, (GF-3). Refer to oil viscosity chart for correct SAE grade. Refer to the Vehicle Emission Control Information label in the engine compartment.
MAINTAINING YOUR VEHICLE 313 Chassis Component Automatic Transmission AWD Power Transfer Unit AWD Overrunning Clutch AWD Rear Carrier Brake Master Cylinder Power Steering Reservoir Fluids, Lubricants and Genuine Parts Mopart ATF+4 Automatic Transmission Fluid. Mopart Gear Lubricant 75W-90. Mopart ATF+4 Automatic Transmission Fluid. Mopart Gear Lubricant 75W-90. Mopart DOT 3 and SAE J1703 should be used. If DOT 3 brake fluid is not available, then DOT 4 or DOT 4+ is acceptable.
MAINTENANCE SCHEDULES CONTENTS M A I N T E N A N C E m Emission Control System Maintenance . . . . . . . . 316 ▫ Schedule “B” . . . . . . . . . . . . . . . . . . . . . . . . 319 m Maintenance Schedules . . . . . . . . . . . . . . . . . . . 316 ▫ Schedule “A” . . . . . . . . . . . . . . . . . . . . . . . .
M A I N T E N A N C E 316 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
MAINTENANCE SCHEDULES • Taxi, police, or delivery service (commercial service).L • Off-road or desert operation. NOTE: If ANY of these apply to you then change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first and follow schedule “B” of the 9Maintenance Schedules9 section of this manual. NOTE: Most vehicles are operated under the conditions listed for Schedule 9B9. Second is Schedule “A”.
M A I N T E N A N C E 318 MAINTENANCE SCHEDULES Once a Month • Inspect the brake hoses. • Check tire pressure and look for unusual wear or damage. • Inspect the CV joints and front suspension components. • Inspect the battery and clean and tighten the terminals as required. • Check the automatic transmission fluid level. • Check the fluid levels of coolant bottle, brake master S cylinder and transmission, add as needed.
SCHEDULE “B” SCHEDULE “B” Follow schedule “B” if you usually operate your vehicle under one or more of the following conditions. Change the automatic transmission fluid and filter every 60,000 miles (96 000 km) if the vehicle is usually operated under one or more of the conditions marked with an L. • Day or night temperatures are below 32° F (0° C). • Stop and go driving. • Extensive engine idling. • Driving in dusty conditions. • Short trips of less than 10 miles (16 km).
M 320 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter. A Inspect the brake linings. N C Inspect the engine air cleaner filter, replace if E necessary. * S C H E D U L E S 8 Replace the engine air cleaner filter. * Change the All Wheel Drive (AWD) power transfer unit fluid. (See note at the end of this chart) Relpace the air conditioning filter.
SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter. Inspect the tie rod ends and boot seals. (Front & Rear) Inspect the PCV valve and replace as necessary.* Change the All Wheel Drive (AWD) power transfer unit fluid. (See note at the end of this chart) Change the All Wheel Drive (AWD) overrunning clutch and rear carrier fluid.
M 322 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter. A Inspect the brake linings. N C Inspect the engine air cleaner filter, replace if E necessary. * S C H E D U L E S 8 Replace the engine air cleaner filter. * Change the All Wheel Drive power transfer unit fluid. (See the note at the end of this chart.) Change the All Wheel Drive (AWD) overrunning clutch and rear carrier fluid. (See note at the end of this chart) Relpace the air conditioning filter.
SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter. Inspect the tie rod ends and boot seals. (Front & Rear) Inspect the PCV valve and replace if necessary.* Inspect the serpentine drive belt, replace if necessary. ‡ Change the automatic transmission fluid and filter. Change the All Wheel Drive (AWD) power transfer unit fluid.
M 324 SCHEDULE “B” A I N Miles T (Kilometers) E N Change the All Wheel Drive (AWD) overrunA ning clutch and rear carrier fluid. (See note at N the end of this chart) C E Relpace the air conditioning filter.
SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter Replace the spark plugs on 3.5 liter engines. Inspect the tie rod ends and boot seals. (Front & Rear) Check the PCV valve and replace if necessary. Not required if previously changed.* Inspect the serpentine drive belt, replace if necessary. ‡ Change the All Wheel Drive power transfer unit fluid.
M 326 SCHEDULE “B” A I N Miles T (Kilometers) E N Change the All Wheel Drive (AWD) overrunA ning clutch and rear carrier fluid. (See note at N the end of this chart) C E Relpace the air conditioning filter.
SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter * Change the All Wheel Drive (AWD) power transfer unit fluid. (See note at the end of this chart) Change the All Wheel Drive (AWD) overrunning clutch and rear carrier fluid. (See note at the end of this chart) Inspect the serpentine drive belt, replace if necessary.
M 328 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter. A Inspect the brake linings. N C Inspect the engine air cleaner filter, replace if necesE sary. * S C H E D U L E S 8 Replace the engine air cleaner filter. Inspect the tie rod ends and boot seals. (Front & Rear) Inspect the PCV valve and replace as necessary.* Inspect the serpentine drive belt, replace if necessary. ‡ Change the automatic transmission fluid and filter.
SCHEDULE “B” * This maintenance is recommended by the manufacture to the owner but is not required to maintain the emissions warranty. ‡ This maintenance is not required if previously replaced. Inspection and service should also be performed anytime a malfunction is observed or suspected. Retain all receipts.
M 330 SCHEDULE “A” A I SCHEDULE “A” N T Miles E N (Kilometers) A [Months] N C Change engine oil and engine oil filter. E Inspect the brake linings. S C H E D U L E S 8 Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter. Inspect the tie rod ends and boot seals. (Front & Rear) Relpace the air conditioning filter.
SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter. Inspect the tie rod ends and boot seals. (Front & Rear) Check the PCV valve and replace, if necessary.* Inspect the serpentine drive belt, replace if necessary. ‡ Flush and replace the engine coolant at 60 months, regardless of mileage. Relpace the air conditioning filter.
M 332 SCHEDULE “A” A I N Miles T (Kilometers) E N [Months] A Change engine oil and engine oil filter. N C Inspect the brake linings. E Inspect the engine air cleaner filter, replace if necesS C H E D U L E S 8 sary. * Replace the engine air cleaner filter. Inspect the tie rod ends and boot seals. (Front & Rear) Check and replace the PCV valve , if necessary.* Inspect the serpentine drive belt, replace if necessary. ‡ Replace the spark plugs 3.5 liter engines.
SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter. Inspect the tie rod ends and boot seals. (Front & Rear) Check the PCV valve and replace, if necessary.* Inspect the serpentine drive belt, replace if necessary. ‡ Flush and replace the engine coolant at 120 months, if not done at 100,000 miles (160 000 km). Replace the air conditioning filter.
M 334 SCHEDULE “A” A I WARNING! N T E You can be badly injured working on or around a N motor vehicle. Do only that service work for which A you have the knowledge and the right equipment. If N C you have any doubt about your ability to perform a E S C H E D U L E S 8 service job, take your vehicle to a competent mechanic.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS m Suggestions For Obtaining Service For Your Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 336 ▫ Prepare For The Appointment . . . . . . . . . . . . 336 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . . . 336 m Reporting Safety Defects . . . . . . . . . . . . . . . . . . 340 ▫ In Canada . . . . . . . . . . . . . . . . . . . . . . . . . . 340 m Publication Order Forms . . . . . . . . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty, discuss additional charges with the service manager. Keep a maintenance log of your vehicle’s service history. This can often provide a clue to the current problem.
IF YOU NEED CONSUMER ASSISTANCE The manufacturer has empowered its dealers to make warranty and repair decisions that ensure you are not inconvenienced. There is no need for you to wait for a decision from the manufacturer. If a special circumstance occurs that requires information from the manufacturer, we have asked the dealer’s service management to make the contact on your behalf. This is why you should always talk to your dealer’s service manager first. Most matters can be resolved with this process.
IF YOU NEED CONSUMER ASSISTANCE In Mexico contact: Av. Prolongacion Paseo de la Reforma, 1240 Sante Fe C.P. 05109 Mexico, D. F. In Mexico (915) 729–1248 or 729–1240 Outside Mexico (525) 729–1248 or 729–1240 Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommunication Devices for the Deaf) equipment at its Customer Center.
IF YOU NEED CONSUMER ASSISTANCE 339 Contract, and you require service after your manufacturer’s new vehicle limited warranty expires, please refer to your contract documents, and contact the person listed in those documents. We appreciate that you have made a major investment when you purchased your new vehicle. Your dealer has also made a major investment in facilities, tools, and training to assure that you are absolutely delighted with your ownership experience.
IF YOU NEED CONSUMER ASSISTANCE REPORTING SAFETY DEFECTS In the 50 United States and Washington D.C.: If you believe that your vehicle has a defect which could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying the manufacturer.
IF YOU NEED CONSUMER ASSISTANCE • Service Manuals. These comprehensive service manuals provide the information that students and professional technicians need in diagnosing/troubleshooting, problem solving, maintaining, servicing and repairing DaimlerChrysler Corporation vehicles. A complete working knowledge of the vehicle, system and/or components is written in straightforward language with illustrations, diagrams and charts. • Diagnostic Procedure Manuals.
IF YOU NEED CONSUMER ASSISTANCE DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES The following describes the tire grading categories established by the National highway Traffic Safety Administration. The specific grade rating assigned by the tire’s manufacturer in each category is shown on the sidewall of the tires on your car. All Passenger Car Tires Must Conform to Federal Safety Requirements in Addition to These Grades.
IF YOU NEED CONSUMER ASSISTANCE Temperature Grades The temperature grades are A (highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
INDEX 10
INDEX Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 240 Adding Washer Fluid . . . . . . . . . . . . . . . . . . 109,285 Additives, Fuel . . . . . . . . . . . . . . . . . . . . . . . . . 238 Adjustable Pedals . . . . . . . . . . . . . . . . . . . . . . . . 99 Air Conditioner Maintenance . . . . . . . . . . . . . . . 281 Air Conditioning Filter . . . . . . . . . . . . . . . . . 192,282 Air Conditioning Refrigerant . . . . . . . . . . . . . . . 281 Air Conditioning System . . . . . .
INDEX 347 Special Additives . . . . . . . . . . . . . . . . . . . . . . 298 Autostick . . . . . . . . . . . . . . . . . . . . . . . . 112,203,204 Bulb Replacement . . . . . . . . . . . . . . . . . . . . . . . 307 Bulbs, Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . 306 Ball Joints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 283 Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 279 Jump Starting . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Cellular Phone . . . . . . . . . . . . . . . . . . . . . . . . . . 73 Chains, Tire . . . . . . . . . . . . . . . . . . . . . . . . . . . . 233 Changing A Flat Tire . . . . . . . . . . . . . . . . . . . . . 252 Child Restraint . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Child Restraint Tether Anchors . . . . . . . . . . . . . 53,55 Child Safety Locks . . . . . . . . . . . . . . . . . . . . . . . . 18 Child Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Defroster, Rear Window . . . . . . . . . . . . . . . . . . . 193 Defroster, Windshield . . . . . . . . . . . . . . . . . . . 63,188 Delay Wipers . . . . . . . . . . . . . . . . . . . . . . . . . . . 108 Digital Video Disc Player . . . . . . . . . . . . . . . . . . 170 Dimmer Switch, Headlight . . . . . . . . . . . . . . . . . 107 Dipsticks Automatic Transaxle . . . . . . . . . . . . . . . . . . . . 296 Disposal Antifreeze . . . . . . . . . . . . . . . . . . . . . . . . . . . 290 Door Locks . . . . .
INDEX Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 272,312 Oil Change Interval . . . . . . . . . . . . . . . . . . . . 274 Oil Selection . . . . . . . . . . . . . . . . . . . . . . . . . . 274 Oil Synthetic . . . . . . . . . . . . . . . . . . . . . . . . . 276 Overheating . . . . . . . . . . . . . . . . . . . . . . . . . . 251 Temperature Gauge . . . . . . . . . . . . . . . . . . . . . 138 Exhaust Gas Caution . . . . . . . . . . . . . . 29,62,239,286 Exhaust System . . . . . . . . .
INDEX Hoses . . . . . Octane Rating Requirements Tank Capacity Fueling . . . . . . Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 294 . . . . . . . . . . . . . . . . . . . . . . 235,312 . . . . . . . . . . . . . . . . . . . . . . . . . 235 . . . . . . . . . . . . . . . . . . . . . . . . 311 . . . . . . . . . . . . . . . . . . . . . . . . . 240 . . . . . . . . . . . . . . . . . . . . . . . . . 305 Garage Door Opener . Gas Cap . . . . . . . . . . Gasoline . . . . . . . . . .
INDEX Holder, Cup . . . . . . . . . . . . . . . . . . . . . . . . . . . 126 Homelink Transmitter . . . . . . . . . . . . . . . . . . . . . 115 Hood Release . . . . . . . . . . . . . . . . . . . . . . . . . . 100 Hoses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 291,294 Ignition Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Illuminated Entry . . . . . . . . . . . . . . . . . . . . . . . . 15 Immobilizer . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Latches Hood . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 Lead Free Gasoline . . . . . . . . . . . . . . . . . . . . . . 235 Liftgate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63,102 Airbag . . . . . . . . . . . . . . . . . . . . . . . . 47,52,63,145 Anti-Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . 139 Automatic Headlights . . . . . . . . . . . . . . . . . . . 105 Back-Up .
INDEX Load Leveling System . . . . . . . . . . . . . . . . . . . . 132 Loading Vehicle . . . . . . . . . . . . . . . . . . . . . . 241,243 Capacities . . . . . . . . . . . . . . . . . . . . . . . . . . . 243 Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 218 Locks Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Lower Anchors and Tether for CHildren (LATCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53,55 Lubrication, Body . . . . . . . . . . .
INDEX Occupant Restraints . . . . . . . . . . . . . . . . . . . . . . . 31 Octane Rating, Gasoline . . . . . . . . . . . . . . . . . . . 235 Odometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142 Oil, Engine . . . . . . . . . . . . . . . . . . . . . . . . . 272,312 Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . 311 Change Interval . . . . . . . . . . . . . . . . . . . . . . . 274 Checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . 272 Disposal . . . . . . . .
INDEX Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 Outlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124 Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85 Steering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 211 Steering, Checking . . . . . . . . . . . . . . . . . . . . . 282 Sunroof . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121 Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Roof Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130 Rotation, Tires . . . . . . . . . . . . . . . . . . . . . . . . . . 234 Safety Checks Inside Vehicle . . . . . . . . . . . . . . . . . 62 Safety Checks Outside Vehicle . . . . . . . . . . . . . . . 63 Safety, Exhaust Gas . . . . . . . . . . . . . . . . . . . . . . . 29 Safety Information, Tire . . . . . . . . . . . . . . . . . . . 213 Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 Schedule, Maintenance .
INDEX Shoulder Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Side Airbag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Signals, Turn . . . . . . . . . . . . . . . . . . . . . 139,309,310 Slippery Surfaces, Driving On . . . . . . . . . . . . . . . 259 Snow Chains . . . . . . . . . . . . . . . . . . . . . . . . . . . 233 Snow Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . 234 Spare Tire . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Tie Down Hooks, Cargo . . . . . . . . . . . . . . . . . . . 128 Tilt Steering Column . . . . . . . . . . . . . . . . . . . . . 110 Tire and Loading Information Placard . . . . . . . . . 218 Tire Markings . . . . . . . . . . . . . . . . . . . . . . . . . . 213 Tire Safety Information . . . . . . . . . . . . . . . . . . . . 213 Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63,222,342 Alignment . . . . . . . . . . . . . . . . . . . . . . . . . . . 229 Chains . . . . . . . . . . . . . . .
INDEX Selection of Lubricant . . . . . . . . . . . . . . . . 295,313 Transmission . . . . . . . . . . . . . . . . . . . . . See Transaxle Transmitter Battery Service . . . . . . . . . . . . . . . . . . 23 Transmitter, Garage Door Opener . . . . . . . . . . . . 115 Transmitter, Remote Keyless Entry . . . . . . . . . . . . 19 Transporting Pets . . . . . . . . . . . . . . . . . . . . . . . . 61 Tread Wear Indicators . . . . . . . . . . . . . . . . . . . . 228 Trip Odometer . . . . . . . . . . . . . . . .
INDEX 361 Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Windshield Washers . . . . . . . . . . . . . . . . . . . 107,285 Windshield Wiper Blades . . . . . . . . . . . . . . . . . . 284 Windshield Wipers . . . . . . . . . . . . . . . . . . . . . . . 107 Wiper Blade Replacement . . . . . . . . . . . . . . . . . . 284 Wiper, Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108 Wipers, Intermittent . . . . . . . . . . . . . . . . . . . . . .
