User`s manual

8
GBGB
GBGB
GB
P5 = Function of Out 2P5 = Function of Out 2
P5 = Function of Out 2P5 = Function of Out 2
P5 = Function of Out 2
0 = Not used or used as event (P22 = 3, 4, 6, 7)
1 = Alarm 1 output - Process alarm
2 = Alarm 1 output - Band alarm
3 = Alarm 1 output - Deviation alarm
4 = Alarm 1 output - Instrument failure alarm
5 = Cooling out
NOTES:NOTES:
NOTES:NOTES:
NOTES:
1) Setting P5 = 1, 2, 3:
- if parameter
OLHOLH
OLHOLH
OLH is less than 0, it is set to
100;
- if parameter
IPIP
IPIP
IP is less than 0, it is set to 30;
- if parameters
AL1AL1
AL1AL1
AL1 is out of range, it will be
aligned to the lowest value.
2) Setting P5 = 0 or 4:
- if parameter
OLHOLH
OLHOLH
OLH is less than 0, it is set to
100;
- if parameter
IPIP
IPIP
IP is less than 0, it is set to 30;
3) Setting P5 = 5:
- parameter P4 automatically assumes the value
“
rEUrEU
rEUrEU
rEU”;
- if parameter P16 is out of range, it will be
aligned to the lowest value;
- if parameter Pb is not 0 and is lower than 1.5,
it is set to 1.5.
4) Setting P5 different 0:
- if P22 parameter is equal to 3, 4, 6 or 7 it will
be forced to 0.
P6 = Configuration Out 2P6 = Configuration Out 2
P6 = Configuration Out 2P6 = Configuration Out 2
P6 = Configuration Out 2
P6 is skipped when P5 = 0.
If P5 = 1, 3 or 4;
H.A.H.A.
H.A.H.A.
H.A. =
High alarm with automatic reset
L.A.L.A.
L.A.L.A.
L.A. = Low alarm with automatic reset
H.L.H.L.
H.L.H.L.
H.L. = High alarm with manual reset
L.L.L.L.
L.L.L.L.
L.L. = Low alarm with manual reset
When P5 = 4, the "high" or "low" selection has no
effect.
P2 = Initial range valueP2 = Initial range value
P2 = Initial range valueP2 = Initial range value
P2 = Initial range value
Initial range value for input from thermocouple/
Resistance Temperature Detector.
NOTESNOTES
NOTESNOTES
NOTES:
1) When P2 has been modified, the
rLrL
rLrL
rL parameter
will be aligned to it and
rHrH
rHrH
rH parameter will be
forced to P3 value is
rHrH
rHrH
rH <
rLrL
rLrL
rL.
2) When P2 has been modified, if the alarms are
programmed as process alarms (P5=1 and/or
P22=1) and the alarm thresholds are out of
range,
AL.1AL.1
AL.1AL.1
AL.1 and/or
AL. 2AL. 2
AL. 2AL. 2
AL. 2 will be aligned to P2.
P3 = Full range valueP3 = Full range value
P3 = Full range valueP3 = Full range value
P3 = Full range value
Full range value for input from thermocouple/
Resistance Temperature Detector.
NOTESNOTES
NOTESNOTES
NOTES: The minimum input span (P3 - P2) is
300°C or 600°F for TC input and 100°C or 200°F
for RTD input.
On every parameter change P1, P2 is forced to
the minimum value, P3 to the maximum value.
If the value of P2 and/or P3 is modified the
parameter rL is automatically aligned to the new
value (of P2 and/or P3).
If P5 = 1, parameter rL is checked and
automatically aligned if it is out of range.
P4 = Out 1 actionP4 = Out 1 action
P4 = Out 1 actionP4 = Out 1 action
P4 = Out 1 action
This parameter is not modifiable when P5 = 5
rEUrEU
rEUrEU
rEU = reverse action (Heating)
dirdir
dirdir
dir = direct action (Cooling)
t
Input
t
Input
t
Out
t
Out
ReverseReverse
ReverseReverse
Reverse
DirectDirect
DirectDirect
Direct
1601-03-1-CX.pmd 13/01/2004, 10.428