Setup guide
Table Of Contents
- 1 Introduction
- 2 Installation and Setup
- 2.1 Assembly and Connection of Components
- 2.2 Installing and Connecting Sources
- 2.3 Connecting for Communications
- 2.4 Adjust Tilt and Leveling
- 2.5 Initial Power Up
- 2.6 Maximizing Light Output
- 2.7 Basic Image Alignment
- 2.8 Offset and Boresight Alignment
- 2.9 Fold Mirror and Convergence Adjustments
- 2.10 Calibrating the System Using DCP Librarian Setup Software
- 2.11 Phase Balancing
- 3 Basic Operation
- 4 Maintenance
- 4.1 Warnings and Guidelines
- 4.2 Maintaining Proper Cooling
- 4.3 Maintenance and Cleaning
- 4.4 Replacing Lamp and Filter
- 4.4.1 Lamp Replacement Procedure
- Turn OFF Main AC
- Turn OFF Remaining Circuit Breakers
- Disconnect projector from AC supply.
- Open Lamp Door
- Open Cooling Compartment
- Remove Old Lamp and Inspect Reflector
- Remove New Lamp from Protective Cover
- Install New Lamp
- Check Leads
- Close cooling compartment and lamp door
- Turn breakers ON
- Set proper LAMP TYPE (power)
- Turn Lamp ON
- Adjust Lamp Position
- Record Serial Number of New Lamp
- 4.4.2 Filter Replacement Procedure
- 4.4.1 Lamp Replacement Procedure
- 4.5 Lens Replacement Procedure
- 5 Troubleshooting
- 5.1 Power
- 5.2 Lamp
- 5.3 TPC
- 5.4 Ethernet
- 5.5 Cinema Displays
- 5.6 Non-Cinema Displays
- 5.6.1 Projector is ON But There’s No Display
- 5.6.2 The Display is Jittery or Unstable
- 5.6.3 The Display is Faint
- 5.6.4 Upper Portion of Display Waving, Tearing or Jittering
- 5.6.5 Portions of Display Cut-off or Warp to the Opposite Edge
- 5.6.6 Display Appears Compressed (Vertically)
- 5.6.7 Data is Cropped from Edges
- 5.6.8 Display Quality Appears to Drift from Good to Bad and Vice Versa
- 5.6.9 Display Suddenly Freezes
- 5.6.10 Display Colors Not Accurate
- 5.6.11 Display Not Rectangular
- 5.6.12 Display is “Noisy”
- 5.6.13 Random Streaks at Bottom of Image
CP2000 Setup Guide 1-1
020-100070-01 Rev. 1 (10/08)
1 Introduction
The content of this manual applies to the following products only:
• CP2000-i models
• CP2000-h models
• CP2000-S* models - See also enclosed addendum for CP2000-S ballast configuration and additional
specifications.
1.1 THE PROJECTOR
The CP2000 is a professional quality, easy-to-use DMD
projector utilizing Digital Light Processing (DLP
) Cinema
technology from Texas Instruments. Integrating smoothly into
traditional projection environments such as theatres and other
wide screen exhibitor venues.These projectors provide stunning
wide-screen high-resolution cinema images that remain flawless
from first release to final show—truly the solution for critical
digital cinema applications. CP2000 interfaces with local
networks typical in theatres throughout the world, and can be
expanded even further by connecting non-cinema DVI source
material for multimedia presentations from a variety of formats.
1.1.1 FEATURES
• DLP Cinema
3-chip electronics with 2048 x 1080 native
resolution
• Versatile electronic and optical scaling to fill wide screens
• CineBlack
and CinePalette
for deep film-like blacks and superior colorimetry
• CineCanvas
for flexible telecine-grade resizing, subtitling, and other text and graphic overlays
• Two SMPTE 292M cinema inputs, used individually or simultaneously for high-speed dual-link
processing, and each supporting CineLink
®
2 local link encryption
• Dual DVI (Digital Visual Interface) connectors for alternative “non-cinema” content, used individ-
ually or simultaneously for high-speed dual-link processing.
• Choice of 2 models, each with choice of 2 lamp sizes
• Screen brightness: Up to 14 fL on 75-ft. screen (CP2000h and -S) or 50-ft. screen (CP2000i)
• Achievable contrast ratio 500:1 ANSI, 1700:1 full field on/off in center.
• LampLOC
motorized lamp alignment (automatic or custom bulb positioning)
• LiteLOC
for maintaining brightness over time
FIGURE 1-1 CP SERIES PROJECTOR