Setup guide
Table Of Contents
- 1 Introduction
- 2 Installation and Setup
- 2.1 Assembly and Connection of Components
- 2.2 Installing and Connecting Sources
- 2.3 Connecting for Communications
- 2.4 Adjust Tilt and Leveling
- 2.5 Initial Power Up
- 2.6 Maximizing Light Output
- 2.7 Basic Image Alignment
- 2.8 Offset and Boresight Alignment
- 2.9 Fold Mirror and Convergence Adjustments
- 2.10 Calibrating the System Using DCP Librarian Setup Software
- 2.11 Phase Balancing
- 3 Basic Operation
- 4 Maintenance
- 4.1 Warnings and Guidelines
- 4.2 Maintaining Proper Cooling
- 4.3 Maintenance and Cleaning
- 4.4 Replacing Lamp and Filter
- 4.4.1 Lamp Replacement Procedure
- Turn OFF Main AC
- Turn OFF Remaining Circuit Breakers
- Disconnect projector from AC supply.
- Open Lamp Door
- Open Cooling Compartment
- Remove Old Lamp and Inspect Reflector
- Remove New Lamp from Protective Cover
- Install New Lamp
- Check Leads
- Close cooling compartment and lamp door
- Turn breakers ON
- Set proper LAMP TYPE (power)
- Turn Lamp ON
- Adjust Lamp Position
- Record Serial Number of New Lamp
- 4.4.2 Filter Replacement Procedure
- 4.4.1 Lamp Replacement Procedure
- 4.5 Lens Replacement Procedure
- 5 Troubleshooting
- 5.1 Power
- 5.2 Lamp
- 5.3 TPC
- 5.4 Ethernet
- 5.5 Cinema Displays
- 5.6 Non-Cinema Displays
- 5.6.1 Projector is ON But There’s No Display
- 5.6.2 The Display is Jittery or Unstable
- 5.6.3 The Display is Faint
- 5.6.4 Upper Portion of Display Waving, Tearing or Jittering
- 5.6.5 Portions of Display Cut-off or Warp to the Opposite Edge
- 5.6.6 Display Appears Compressed (Vertically)
- 5.6.7 Data is Cropped from Edges
- 5.6.8 Display Quality Appears to Drift from Good to Bad and Vice Versa
- 5.6.9 Display Suddenly Freezes
- 5.6.10 Display Colors Not Accurate
- 5.6.11 Display Not Rectangular
- 5.6.12 Display is “Noisy”
- 5.6.13 Random Streaks at Bottom of Image
5-4 CP2000 Setup Guide
020-100070-01 Rev. 1 (10/08)
Section 5: Troubleshooting
5.5.3 IMAGE VERTICALLY STRETCHED OR “SQUEEZED” INTO CENTER OF SCREEN
Source data converted from film and "pre-squeezed" for CP2000's display format may require use of
the anamorphic lens to regain full "scope" image width and proper proportions.
5.5.4 NO IMAGE, JUST PINK SNOW
1. Make sure the projector's lid is not open. In the event it is open, close the lid and pause or stop the
show on the server. Then, press Play on the server and wait several seconds for the projector to
receive the set of decryption keys (from the server). If after 30 seconds the projector has not
recover, pause or stop the show and try playing again. If this doesn't work, try resetting the server.
2. Make sure the IP octets for the projector and the server (Eth1 port) match.
3. CineCanvas does not have the correct projector IP address. Check the IP address of the projector
and server and change if necessary. They should match.
5.6 NON-CINEMA DISPLAYS
5.6.1 PROJECTOR IS ON BUT THERE’S NO DISPLAY
1. Ensure the lens cover is removed.
2. Ensure the douser is OPEN.
3. Ensure the lamp is ignited. If not, press the Lamp button on the TPC.
4. Ensure the correct DVI display button is selected on the TPC.
5. Ensure AC power is connected.
6. Check the cable connections and make sure the alternative source is selected.
7. Can you access test patterns? If so, check your source connections again.
5.6.2 THE DISPLAY IS JITTERY OR UNSTABLE
1. If the non-cinema display is jittery or blinking erratically, ensure the source is properly connected
and of adequate quality for detection. With a poor quality or improperly connected source, the
projector will repeatedly attempt to display an image.
2. The horizontal or vertical scan frequency of the input signal may be out of range for the projector.
For scan frequency ranges, refer to Section 8: Specifications in the CP2000 User’s Manual.
3. The sync signal may be inadequate. Correct the source problem.
5.6.3 THE DISPLAY IS FAINT
1. Brightness and/or contrast may be set too low.
2. The source may be double terminated. Ensure the source is terminated only once.
3. The source (if non-video) may need sync tip clamping.