Setup guide
Table Of Contents
- 1 Introduction
- 2 Installation and Setup
- 2.1 Assembly and Connection of Components
- 2.2 Installing and Connecting Sources
- 2.3 Connecting for Communications
- 2.4 Adjust Tilt and Leveling
- 2.5 Initial Power Up
- 2.6 Maximizing Light Output
- 2.7 Basic Image Alignment
- 2.8 Offset and Boresight Alignment
- 2.9 Fold Mirror and Convergence Adjustments
- 2.10 Calibrating the System Using DCP Librarian Setup Software
- 2.11 Phase Balancing
- 3 Basic Operation
- 4 Maintenance
- 4.1 Warnings and Guidelines
- 4.2 Maintaining Proper Cooling
- 4.3 Maintenance and Cleaning
- 4.4 Replacing Lamp and Filter
- 4.4.1 Lamp Replacement Procedure
- Turn OFF Main AC
- Turn OFF Remaining Circuit Breakers
- Disconnect projector from AC supply.
- Open Lamp Door
- Open Cooling Compartment
- Remove Old Lamp and Inspect Reflector
- Remove New Lamp from Protective Cover
- Install New Lamp
- Check Leads
- Close cooling compartment and lamp door
- Turn breakers ON
- Set proper LAMP TYPE (power)
- Turn Lamp ON
- Adjust Lamp Position
- Record Serial Number of New Lamp
- 4.4.2 Filter Replacement Procedure
- 4.4.1 Lamp Replacement Procedure
- 4.5 Lens Replacement Procedure
- 5 Troubleshooting
- 5.1 Power
- 5.2 Lamp
- 5.3 TPC
- 5.4 Ethernet
- 5.5 Cinema Displays
- 5.6 Non-Cinema Displays
- 5.6.1 Projector is ON But There’s No Display
- 5.6.2 The Display is Jittery or Unstable
- 5.6.3 The Display is Faint
- 5.6.4 Upper Portion of Display Waving, Tearing or Jittering
- 5.6.5 Portions of Display Cut-off or Warp to the Opposite Edge
- 5.6.6 Display Appears Compressed (Vertically)
- 5.6.7 Data is Cropped from Edges
- 5.6.8 Display Quality Appears to Drift from Good to Bad and Vice Versa
- 5.6.9 Display Suddenly Freezes
- 5.6.10 Display Colors Not Accurate
- 5.6.11 Display Not Rectangular
- 5.6.12 Display is “Noisy”
- 5.6.13 Random Streaks at Bottom of Image
CP2000 Setup Guide 5-1
020-100070-01 Rev. 1 (10/08)
5 Troubleshooting
If the projector does not appear to be operating properly, note the symptoms present and use the
following guide to assist you. If you cannot resolve the problems yourself, contact your dealer for
assistance.
5.1 POWER
5.1.1 PROJECTOR WILL NOT START
1. Check for green Main AC light on projector. If not ON, check all breakers on projector and at the
wall. There are single-phase and 3-phase.
2. Are the CP breakers staying on when enabled? If they are "tripping" to OFF position, there is an
electrical problem requiring investigation by a certified electrician.
5.2 LAMP
5.2.1 LAMP DOES NOT IGNITE
1. If the Lamp button is entirely disabled (not selectable at the TPC Main menu, indicated by a red
"X" on the Lamp button), there is an interlock failure such as an open lamp door, failed lamp fan,
etc. A flashing red alarm window also indicates this. For more information, refer to Table 3.2
Alarm Conditions and Solutions in the CP2000 User’s Manual.
2. For SSM communication failures, re-boot and try again.
3. If a DMDs temperature is too high (DMD Over Critical Temp Limit), the lamp will not
ignite. Cool the projector and try again.
4. If the Status menu indicates a ballast communication problem, re-boot and try again.
5. If the lamp does not ignite after a second try, replace the lamp.
6. If there is no "buzzing" indicating that the igniter is attempting ignition, there may be a problem
with the igniter (Christie service required).
7. If there is a brief "buzz" while attempting ignition, but a lamp does not ignite, the lamp likely
needs to be replaced.