Setup guide
Table Of Contents
- 1 Introduction
- 2 Installation and Setup
- 2.1 Assembly and Connection of Components
- 2.2 Installing and Connecting Sources
- 2.3 Connecting for Communications
- 2.4 Adjust Tilt and Leveling
- 2.5 Initial Power Up
- 2.6 Maximizing Light Output
- 2.7 Basic Image Alignment
- 2.8 Offset and Boresight Alignment
- 2.9 Fold Mirror and Convergence Adjustments
- 2.10 Calibrating the System Using DCP Librarian Setup Software
- 2.11 Phase Balancing
- 3 Basic Operation
- 4 Maintenance
- 4.1 Warnings and Guidelines
- 4.2 Maintaining Proper Cooling
- 4.3 Maintenance and Cleaning
- 4.4 Replacing Lamp and Filter
- 4.4.1 Lamp Replacement Procedure
- Turn OFF Main AC
- Turn OFF Remaining Circuit Breakers
- Disconnect projector from AC supply.
- Open Lamp Door
- Open Cooling Compartment
- Remove Old Lamp and Inspect Reflector
- Remove New Lamp from Protective Cover
- Install New Lamp
- Check Leads
- Close cooling compartment and lamp door
- Turn breakers ON
- Set proper LAMP TYPE (power)
- Turn Lamp ON
- Adjust Lamp Position
- Record Serial Number of New Lamp
- 4.4.2 Filter Replacement Procedure
- 4.4.1 Lamp Replacement Procedure
- 4.5 Lens Replacement Procedure
- 5 Troubleshooting
- 5.1 Power
- 5.2 Lamp
- 5.3 TPC
- 5.4 Ethernet
- 5.5 Cinema Displays
- 5.6 Non-Cinema Displays
- 5.6.1 Projector is ON But There’s No Display
- 5.6.2 The Display is Jittery or Unstable
- 5.6.3 The Display is Faint
- 5.6.4 Upper Portion of Display Waving, Tearing or Jittering
- 5.6.5 Portions of Display Cut-off or Warp to the Opposite Edge
- 5.6.6 Display Appears Compressed (Vertically)
- 5.6.7 Data is Cropped from Edges
- 5.6.8 Display Quality Appears to Drift from Good to Bad and Vice Versa
- 5.6.9 Display Suddenly Freezes
- 5.6.10 Display Colors Not Accurate
- 5.6.11 Display Not Rectangular
- 5.6.12 Display is “Noisy”
- 5.6.13 Random Streaks at Bottom of Image
3-2 CP2000 Setup Guide
020-100070-01 Rev. 1 (10/08)
Section 3: Basic Operation
3. When the TPC has initialized (approx. 15-30 seconds, indicated by a green circle in the left
corner), press the Lamp button on the TPC Main menu to ignite the lamp.
If the lamp does not ignite:
• If a safety interlock switch is open (such as when the lamp door is ajar), the lamp cannot be struck.
The Lamp button will be disabled until the interlock problem is resolved. An alarm window also
appears on the TPC.
• If the lamp fails to ignite even though the interlock system is OK, the projector automatically
retries ignition using 100% of the maximum power acceptable for the installed lamp. If this also
fails, a new lamp is likely needed.
For complete power-up troubleshooting, refer to Section 5 Troubleshooting
.
3.2 POWER DOWN PROCEDURE
1. From the main TPC menu press the Lamp button to turn the lamp OFF (briefly hold the button
down).
2. Wait approximately 10 minutes to allow fans to cool the lamp.
3. At the operator's side of the pedestal, set all breakers to OFF (Figure 3-2 Power-down Procedure).
NOTE: Manual shut-down only. Optional automation not yet available from Christie.
FIGURE 3-2 POWER-DOWN PROCEDURE