Setup guide
Table Of Contents
- 1 Introduction
- 2 Installation and Setup
- 2.1 Assembly and Connection of Components
- 2.2 Installing and Connecting Sources
- 2.3 Connecting for Communications
- 2.4 Adjust Tilt and Leveling
- 2.5 Initial Power Up
- 2.6 Maximizing Light Output
- 2.7 Basic Image Alignment
- 2.8 Offset and Boresight Alignment
- 2.9 Fold Mirror and Convergence Adjustments
- 2.10 Calibrating the System Using DCP Librarian Setup Software
- 2.11 Phase Balancing
- 3 Basic Operation
- 4 Maintenance
- 4.1 Warnings and Guidelines
- 4.2 Maintaining Proper Cooling
- 4.3 Maintenance and Cleaning
- 4.4 Replacing Lamp and Filter
- 4.4.1 Lamp Replacement Procedure
- Turn OFF Main AC
- Turn OFF Remaining Circuit Breakers
- Disconnect projector from AC supply.
- Open Lamp Door
- Open Cooling Compartment
- Remove Old Lamp and Inspect Reflector
- Remove New Lamp from Protective Cover
- Install New Lamp
- Check Leads
- Close cooling compartment and lamp door
- Turn breakers ON
- Set proper LAMP TYPE (power)
- Turn Lamp ON
- Adjust Lamp Position
- Record Serial Number of New Lamp
- 4.4.2 Filter Replacement Procedure
- 4.4.1 Lamp Replacement Procedure
- 4.5 Lens Replacement Procedure
- 5 Troubleshooting
- 5.1 Power
- 5.2 Lamp
- 5.3 TPC
- 5.4 Ethernet
- 5.5 Cinema Displays
- 5.6 Non-Cinema Displays
- 5.6.1 Projector is ON But There’s No Display
- 5.6.2 The Display is Jittery or Unstable
- 5.6.3 The Display is Faint
- 5.6.4 Upper Portion of Display Waving, Tearing or Jittering
- 5.6.5 Portions of Display Cut-off or Warp to the Opposite Edge
- 5.6.6 Display Appears Compressed (Vertically)
- 5.6.7 Data is Cropped from Edges
- 5.6.8 Display Quality Appears to Drift from Good to Bad and Vice Versa
- 5.6.9 Display Suddenly Freezes
- 5.6.10 Display Colors Not Accurate
- 5.6.11 Display Not Rectangular
- 5.6.12 Display is “Noisy”
- 5.6.13 Random Streaks at Bottom of Image
China RoHS Compliance Information
关于中国《电子信息产品污染控制管理办法》的说明
Environmentally Friendly Use Period
环保使用期限
The year number in the centre of the label indicates the Environmentally Friendly Use Period, which is
required to mark on the electronic information product sold in China according to the China RoHS
regulations.
本标志中表示的年数是根据《电子信息产品污染控制管理办法》（2006 年 2 月 28 日）以及《电
子信息产品污染控制标识要求》（2006 年 11 月 6 日）制定的、适用于在中华人民共和国境内销
售的电子信息产品的环保使用期限。
Material Concentration Values Table
有毒有害物质含量表
Material Concentration
(有毒有害物质或元素)
Part Name
部件名称
铅
（Pb）
汞
（Hg）
镉
（Cd）
六价铬
(Cr 6+）
多溴联苯
（PBB）
多溴二联苯醚
（PBDE）
Low voltage power
supply
低压电源
X O O O O O
Breaker/Switch
开关
X O O O O O
Ballast
镇流器
X O O O O X
Line filter
滤波器
X O O O O X
AC relay
继电器
X O O O O O
Ignitor
点火器
X O O O O X
Harness/cable
连接电线/缆
X O O O O X
Enhanced Formatter
Interface Board
增强型格式化板
X O O O O O
Interface Board
接口板
X O O O O O
Motherboard with
Twin DVI
双 DVI 接口主板
X O O O O O
Processor Board
处理板
X O O O O O
Stepper Driver Board
步进驱动板
X O O O O O
System Supervisor
Module
系统监控模块
X O O O O O
Liquid Cooling
system
液体冷却系统
O O O O O O
Touch Panel
Controller
触摸屏控制器
X O O O O O
Ethernet Hub
以太网集线器
X O O O O O
Blower/Fan
吹风机/风扇
O O O O O O
Sensor
传感器
O O O O O O
Illumination optics
system
照明光学系统
X O X O O O
Projection Lens
投影镜头
X O X O O O
Auxiliary optics
辅助光学器件
X O X O O O
Mechanical
enclosure*
机械附件
X O O O O O
Software CD
软件光盘
O O O O O O
Lamp
灯泡
X O O O O O
Battery
电池
O O O O O O
Note:
O : indicates that the concentration value of the particular hazardous substance contained in all the homogeneous materials for this part,
according to EIP-A, EIP-B, EIP-C, is below the stipulated levels in China SJ/T11363-2006.
表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T11363-2006 规定的限量要求以下。
X: indicates that the concentration value of the particular hazardous substance contained in all the homogeneous materials for this part,
according to EIP-A, EIP-B, EIP-C, may be above the stipulated levels in China SJ/T11363-2006.
表示该有毒有害物质至少在该部件的某一均质材料中的含量可能超出 SJ/T11363-2006 规定的限量要求。
* This part uses metallic alloys, which may contain Lead. 因该部件使用金属合金材料，故可能含有铅。