Setup guide
Table Of Contents
- 1 Introduction
- 2 Installation and Setup
- 2.1 Assembly and Connection of Components
- 2.2 Installing and Connecting Sources
- 2.3 Connecting for Communications
- 2.4 Adjust Tilt and Leveling
- 2.5 Initial Power Up
- 2.6 Maximizing Light Output
- 2.7 Basic Image Alignment
- 2.8 Offset and Boresight Alignment
- 2.9 Fold Mirror and Convergence Adjustments
- 2.10 Calibrating the System Using DCP Librarian Setup Software
- 2.11 Phase Balancing
- 3 Basic Operation
- 4 Maintenance
- 4.1 Warnings and Guidelines
- 4.2 Maintaining Proper Cooling
- 4.3 Maintenance and Cleaning
- 4.4 Replacing Lamp and Filter
- 4.4.1 Lamp Replacement Procedure
- Turn OFF Main AC
- Turn OFF Remaining Circuit Breakers
- Disconnect projector from AC supply.
- Open Lamp Door
- Open Cooling Compartment
- Remove Old Lamp and Inspect Reflector
- Remove New Lamp from Protective Cover
- Install New Lamp
- Check Leads
- Close cooling compartment and lamp door
- Turn breakers ON
- Set proper LAMP TYPE (power)
- Turn Lamp ON
- Adjust Lamp Position
- Record Serial Number of New Lamp
- 4.4.2 Filter Replacement Procedure
- 4.4.1 Lamp Replacement Procedure
- 4.5 Lens Replacement Procedure
- 5 Troubleshooting
- 5.1 Power
- 5.2 Lamp
- 5.3 TPC
- 5.4 Ethernet
- 5.5 Cinema Displays
- 5.6 Non-Cinema Displays
- 5.6.1 Projector is ON But There’s No Display
- 5.6.2 The Display is Jittery or Unstable
- 5.6.3 The Display is Faint
- 5.6.4 Upper Portion of Display Waving, Tearing or Jittering
- 5.6.5 Portions of Display Cut-off or Warp to the Opposite Edge
- 5.6.6 Display Appears Compressed (Vertically)
- 5.6.7 Data is Cropped from Edges
- 5.6.8 Display Quality Appears to Drift from Good to Bad and Vice Versa
- 5.6.9 Display Suddenly Freezes
- 5.6.10 Display Colors Not Accurate
- 5.6.11 Display Not Rectangular
- 5.6.12 Display is “Noisy”
- 5.6.13 Random Streaks at Bottom of Image
2-6 CP2000 Setup Guide
020-100070-01 Rev. 1 (10/08)
Section 2: Installation and Setup
6. Power Cables to Head: From behind the main AC breaker panel (within the pedestal), connect
both identical power cables 34-001992 to the IEC receptacles located near Panel B (100-230 VAC)
and Panel C (200-230 VAC). These cables are interchangeable - connect either cable to either
receptacle and secure with metal strain-relief clip provided (Figure 2-7).
FIGURE 2-7 CONNECT “PROJECTOR” BREAKER POWER CABLES TO PROJECTION HEAD
IMPORTANT! Components in the lamp compartment will require 200-230 VAC.
NOTE: If you prefer to use an uninterrupted power supply (UPS) for supplying power to the
projection head, route the UPS power cables through the pedestal toe and connect to the IEC
receptacles on Panel B (100-230 VAC). In this case, only one power cable provided in the pedestal is
used.
7.
Check Ethernet and TPC Power: Within the pedestal, confirm that the power supplies for the
Ethernet hub and TPC both connect to a power bar wired to the terminal block TB2 from either the
facility power source or the existing projector wiring (Figure 2-8). No other components or
external equipment should be connected here.
NOTE:
This is a current-limited 120 VAC outlet powered by the ballast and separately fused.
FIGURE 2-8 CHECK TPC AND ETHERNET HUB CONNECTIONS TO HUB