Setup guide
Table Of Contents
- 1 Introduction
- 2 Installation and Setup
- 2.1 Assembly and Connection of Components
- 2.2 Installing and Connecting Sources
- 2.3 Connecting for Communications
- 2.4 Adjust Tilt and Leveling
- 2.5 Initial Power Up
- 2.6 Maximizing Light Output
- 2.7 Basic Image Alignment
- 2.8 Offset and Boresight Alignment
- 2.9 Fold Mirror and Convergence Adjustments
- 2.10 Calibrating the System Using DCP Librarian Setup Software
- 2.11 Phase Balancing
- 3 Basic Operation
- 4 Maintenance
- 4.1 Warnings and Guidelines
- 4.2 Maintaining Proper Cooling
- 4.3 Maintenance and Cleaning
- 4.4 Replacing Lamp and Filter
- 4.4.1 Lamp Replacement Procedure
- Turn OFF Main AC
- Turn OFF Remaining Circuit Breakers
- Disconnect projector from AC supply.
- Open Lamp Door
- Open Cooling Compartment
- Remove Old Lamp and Inspect Reflector
- Remove New Lamp from Protective Cover
- Install New Lamp
- Check Leads
- Close cooling compartment and lamp door
- Turn breakers ON
- Set proper LAMP TYPE (power)
- Turn Lamp ON
- Adjust Lamp Position
- Record Serial Number of New Lamp
- 4.4.2 Filter Replacement Procedure
- 4.4.1 Lamp Replacement Procedure
- 4.5 Lens Replacement Procedure
- 5 Troubleshooting
- 5.1 Power
- 5.2 Lamp
- 5.3 TPC
- 5.4 Ethernet
- 5.5 Cinema Displays
- 5.6 Non-Cinema Displays
- 5.6.1 Projector is ON But There’s No Display
- 5.6.2 The Display is Jittery or Unstable
- 5.6.3 The Display is Faint
- 5.6.4 Upper Portion of Display Waving, Tearing or Jittering
- 5.6.5 Portions of Display Cut-off or Warp to the Opposite Edge
- 5.6.6 Display Appears Compressed (Vertically)
- 5.6.7 Data is Cropped from Edges
- 5.6.8 Display Quality Appears to Drift from Good to Bad and Vice Versa
- 5.6.9 Display Suddenly Freezes
- 5.6.10 Display Colors Not Accurate
- 5.6.11 Display Not Rectangular
- 5.6.12 Display is “Noisy”
- 5.6.13 Random Streaks at Bottom of Image
2-4 CP2000 Setup Guide
020-100070-01 Rev. 1 (10/08)
Section 2: Installation and Setup
NOTE: There is no need to adjust leveling and/or tilt at this point. Wait until all other components are
mounted/installed. For more information, refer to 2.4
Adjust Tilt and Leveling.
FIGURE 2-3 ADJUST FEET
INSTALL TPC
1. Attach the Touch Panel Controller, pre-assembled with its
ball joint base and mounting arm, to the matching ball
joint base secured at the rear of the projector (Figure 2-4
Typical TPC Mount).
2. Connect to the TPC cable routed through the nearby hole
in the projector rear. The other end of this cable is pre-
connected to the internal Ethernet hub and the 24V power
supply.
If desired, you can mount the TPC and its 24V power supply
elsewhere at the site. Route the TPC cable through either the
rear or front hole on the projector. Cap unused hole.
CONNECT PRE-INSTALLED CABLING (PEDESTAL-TO-
HEAD)
Numerous cables are pre-installed within the pedestal and must be routed up to the underside of the
projection head, where they connect to one of three panels (or two IEC power sockets).
NOTE: For all cable connections, keep cable ties that have been trimmed at manufacture. Remove
temporary untrimmed ties that have "tails".
FIGURE 2-4 TYPICAL TPC MOUNT