Setup guide
Table Of Contents
- 1 Introduction
- 2 Installation and Setup
- 2.1 Assembly and Connection of Components
- 2.2 Installing and Connecting Sources
- 2.3 Connecting for Communications
- 2.4 Adjust Tilt and Leveling
- 2.5 Initial Power Up
- 2.6 Maximizing Light Output
- 2.7 Basic Image Alignment
- 2.8 Offset and Boresight Alignment
- 2.9 Fold Mirror and Convergence Adjustments
- 2.10 Calibrating the System Using DCP Librarian Setup Software
- 2.11 Phase Balancing
- 3 Basic Operation
- 4 Maintenance
- 4.1 Warnings and Guidelines
- 4.2 Maintaining Proper Cooling
- 4.3 Maintenance and Cleaning
- 4.4 Replacing Lamp and Filter
- 4.4.1 Lamp Replacement Procedure
- Turn OFF Main AC
- Turn OFF Remaining Circuit Breakers
- Disconnect projector from AC supply.
- Open Lamp Door
- Open Cooling Compartment
- Remove Old Lamp and Inspect Reflector
- Remove New Lamp from Protective Cover
- Install New Lamp
- Check Leads
- Close cooling compartment and lamp door
- Turn breakers ON
- Set proper LAMP TYPE (power)
- Turn Lamp ON
- Adjust Lamp Position
- Record Serial Number of New Lamp
- 4.4.2 Filter Replacement Procedure
- 4.4.1 Lamp Replacement Procedure
- 4.5 Lens Replacement Procedure
- 5 Troubleshooting
- 5.1 Power
- 5.2 Lamp
- 5.3 TPC
- 5.4 Ethernet
- 5.5 Cinema Displays
- 5.6 Non-Cinema Displays
- 5.6.1 Projector is ON But There’s No Display
- 5.6.2 The Display is Jittery or Unstable
- 5.6.3 The Display is Faint
- 5.6.4 Upper Portion of Display Waving, Tearing or Jittering
- 5.6.5 Portions of Display Cut-off or Warp to the Opposite Edge
- 5.6.6 Display Appears Compressed (Vertically)
- 5.6.7 Data is Cropped from Edges
- 5.6.8 Display Quality Appears to Drift from Good to Bad and Vice Versa
- 5.6.9 Display Suddenly Freezes
- 5.6.10 Display Colors Not Accurate
- 5.6.11 Display Not Rectangular
- 5.6.12 Display is “Noisy”
- 5.6.13 Random Streaks at Bottom of Image
CP2000 Setup Guide 2-1
020-100070-01 Rev. 1 (10/08)
2 Installation and Setup
This section outlines how to install, connect and optimize the projector.
2.1 ASSEMBLY AND CONNECTION OF COMPONENTS
NOTE: Illustrations apply to either CP model, unless otherwise stated. In some instances the
illustrations may not contain the rear-mount.
These instructions describe how to:
• mount the projection head on to the pedestal
• position the projector relative to the port window and screen
• connect pedestal-to-head cabling and cooling hoses
• customize projector for lamps
• connect exhaust ducting and fill liquid cooling system
• install lens and lamp
• connect to power
2.1.1 BEFORE BEGINNING
You will require the following for installation:
• Full understanding of all site requirements and characteristics
• 12” screwdrivers: Philips (magnetic) and flat
• Assorted wrenches such as 7/8” and ¾”
• Assorted Allen keys such as 3/16”, 7/64”, 5/32”, and M3
• 3-phase 4-wire, 5-wire, or 6-wire connection of AC supply to Terminal Block 1 in pedestal (certi-
fied electrician required).
• Heat extractor (such as inline centrifugal blower Elicent model# AXC 315B) or roof extractor pro-
viding at least 600 CFM at 8” exhaust duct opening @ 600 watts or lower. NOTE: Mount at an
external location.
• Lamp and protective clothing / safety gear
• Laptop computer with DCP Librarian software with Ethernet or standard RS-232 cable
• Vapor-free “dustoff type” compressed air can
• Latex lab gloves
• Lens cleaning tissue and solution (see 6.3, Maintenance & Cleaning)
CAUTION
All installation steps must be performed by qualified technicians. Do not modify circuits
or wiring.