CP2000-M/MR Setup Guide 020-100205-03
TABLE OF CONTENTS 1 Introduction 1.1 Purchase Record and Service Contacts............................................................................1-1 1.1.1 List of Components ..................................................................................................1-1 1.1.2 Key Features ............................................................................................................1-2 2 Basic Operation 2.1 Safety Warnings and Guidelines................................................
TABLE OF CONTENTS Summary of Admin: MCGD Menu Options ............................................................2-25 2.13.4 Admin: TCGD Menu ............................................................................................2-27 Summary of Admin: TCGD Menu Options .............................................................2-27 2.13.5 Admin: Lamp Menu..............................................................................................2-29 2.14 Working with the Lamp .....................
TABLE OF CONTENTS Lens Mount Vertical Boresight .................................................................................3-12 Lens Mount Horizontal Boresight ............................................................................3-13 3.12 Adjustable Fold Mirror & Convergence Adjustments...................................................3-15 3.12.1 DMD Convergence ...............................................................................................3-15 3.12.2 Fold Mirror Adjustment ...
TABLE OF CONTENTS 6.1.2 Ethernet Auxiliary Port ............................................................................................6-1 6.1.3 RS232-A Port (TI Light Engine) .............................................................................6-1 6.1.4 RS232-B Port (PCM) ...............................................................................................6-1 6.1.5 GPIO Port...............................................................................................................
1 Introduction This manual is intended for trained users authorized to operate professional high-brightness projection systems. Only qualified Christie trained service technicians knowledgeable about all potential hazards associated with high voltage, ultraviolet exposure and high temperatures generated by the lamp and associated circuits are authorized to 1) assemble/install the projector and 2) perform service functions inside the projector. 1.
Section 1: Introduction 1.1.
2 Basic Operation 2.1 SAFETY WARNINGS AND GUIDELINES 2.1.1 GENERAL PRECAUTIONS DANGER Never look directly into the projector lens or at the lamp. The extremely high brightness can cause permanent eye damage. For protection from ultraviolet radiation, keep all projector housings intact during operation. Protective safety clothing and safety goggles are recommended when servicing. FIRE HAZARD. Keep hands, clothes and all combustible material away from the concentrated light beam of the lamp.
Section 2: Basic Operation 2.1.2 AC/POWER PRECAUTIONS DANGER Use only the AC power cord supplied. Do not attempt operation if the AC supply and cord are not within the specified voltage and power range. As a safety feature the projector is equipped with a 3-wire plug with a third (grounding) pin. If you are unable to insert the plug into the outlet, contact an electrician to have the outlet replaced. Do not defeat the safety purpose of the grounding-type plug.
Section 2: Basic Operation Cool the Lamp Completely DANGER Lamp may explode causing bodily harm or death. Always wear protective clothing whenever lamp door is open or while handling lamp. Ensure those within the vicinity of the projector are also suited with protective clothing. Never attempt to access the lamp while the lamp is ON. Wait at least 15 minutes after the lamp turns OFF before powering down, disconnecting from AC and opening the lamp door.
Section 2: Basic Operation For all other regions, ensure a line cord, power plug and socket that meet the appropriate rating standards are used. When the main inlet is used the AC switch must be set to A only (Figure 2-2). 2. An optional feature to power all electronics through a UPS is available using the secondary inlet. When the secondary inlet is used the AC switch must be set to the A + B (Figure 2-2).
Section 2: Basic Operation 2.3 POWERING DOWN THE PROJECTOR NOTICE: Once the projector is powered down, the fans continue to run for approximately 15 minutes to ensure the projector and lamp have sufficiently cooled, at which point the fans automatically shutoff. To avoid thermal stress that can lead to premature lamp failure, never unplug the line cord while the fans are running and never unplug to power down. 1. From the CDP, press LAMP OFF.
Section 2: Basic Operation • If the back light turns OFF, push any key to turn it ON again. 2.4.2 Navigating the CDP Menus Most basic controls of the projector are accessed from within the projector’s menu system. There are several groups of related functions, with each group selectable as a menu item in the Main menu (Figure 2-3). Press MENU at any time to display the Main menu. With the Main menu displayed, use the arrow keys to highlight the desired option, then press ENTER to make the selection.
Section 2: Basic Operation Pull-down Lists: Press ENTER to see a pull-down list of the options available for a given parameter. Use the arrow keys to scroll through a list of options or to adjust settings. Press EXIT while in a pulldown list to cancel. Using Slide Bar Controls: In some cases, the current value of a given parameter can be adjusted. Depending on the parameter, the number displayed may have units associated with it or may be expressed as a percentage.
Section 2: Basic Operation 2.5 CHANNEL MENU This password-protected screen requires Advanced, Admin or Service rights. In general, the options available through the Channel menu enable users to tailor projector processing for any type of incoming source. Use the arrow keys to scroll through a list of available channels. Once the desired channel is displayed, press ENTER.
Section 2: Basic Operation 2.5.1 Summary of Edit Channel Menu Options • Input: Identifies/sets the connection (location) of the current source, such as cinema port 292 A or 292 B, or a DVI-D graphics port. • Data Format: Identifies the source type (8-10-12 bit) and whether or not it is packed. The projector processes the incoming signal according to the data format selected here.
Section 2: Basic Operation • Use PCF: Activate to use a pre-defined PCF for this source and prohibit further Channel adjustments (the PCF components of Source, Color Space, Gamma, LUT-CLUT and Target Color will disappear), then select the desired PCF from the PCF File menu. Deactivate to adjust the Channel settings - this is currently recommended for all cinema use.
Section 2: Basic Operation 2.6 LAMP MENU The Lamp menu (Figure 2-5) provides controls for optimizing lamp alignment (LampLOC™), maintaining a consistent light output over time (LiteLOC™), rotating the lamp, or setting a precise power level for the lamp. These options are also available via the web ui Advanced:Lamp menu. For information, refer to the CP2000-M/MR User Manual (020-100123-xx). • LampLOC: This menu selection enables users to either automatically adjust LampLOC™ or to manually adjust each axes.
Section 2: Basic Operation 2.7 LENS CONTROL MENU The Lens Control menu enables users to adjust focus, zoom, and vertical/horizontal offsets of the lens. It also provides the option to calibrate the lens, enable the intelligent lens system (ILS) and perform adjustments in MANUAL mode. These options are also available via the web ui Channel:Lens and Advanced:Lens menus. For information, refer to the CP2000-M/MR User Manual (020-100123-xx).
Section 2: Basic Operation range for the installed lens. Once lens calibration is completed the results for the current lens are saved to the system. • Auto ILS: Auto ILS is a per channel setting that is stored with the channel so when a channel is made active the lens will automatically move to the saved or default position for that channel. If Auto ILS is inactive, a manual adjustment of the lens is required and any channel change will not adjust the lens.
Section 2: Basic Operation 2.8 STATUS MENU There are 3 status LEDs on the CDP for the purpose of indicating projector status. Table 2.3 details the various conditions and meanings of the LEDs. In addition to the visual indicator of the LEDs, the status of specific projector components can be checked through the CDP Status menu (Figure 2-7). The Status menu provides status information on various projector components. These menu features are also available via the web ui Status:System menu.
Section 2: Basic Operation 2.9 CONFIGURATION MENU The Configuration menu provides controls for adjusting the contrast and brightness settings of the CDP, running diagnostic controls, selecting the use of the auxiliary lens, and providing the controls to define and change various Ethernet settings. Similar controls are also available through the web ui. Refer to 2.8 Status Menu for a description of Interrogator controls. Never run Interrogator during a show as this could cause image disruption.
Section 2: Basic Operation 2.10 USING THE WEB USER INTERFACE NOTES: 1) Sample menus are shown throughout this section - text and/or icons may vary according to settings recorded in the password-protected menus. 2) This section outlines the menus available ONLY through the web ui. These options/features are not available via the CDP. In addition to using the CDP, most projector functions can be controlled remotely, typically at a controller such as a PC, via a web user interface on an Ethernet network.
Section 2: Basic Operation Power ON or OFF Enable ( ) Power On to enter STANDBY mode. Power to projector components is present. Disable checkbox to turn power OFF. Turn Lamp ON or OFF Enable Lamp On ( ) to turn the lamp ON. If an error exists, which will not allow the lamp to turn ON, the button is grayed out. Disable checkbox to turn the lamp OFF. Open or Close Douser (Shutter) Enable Douser Open ( ) to open the douser. Disable checkbox to close the douser.
Section 2: Basic Operation To enable ILS: 1. From the Main menu select 1 of the available channels. 2. Enable Test Patterns to bring up a test pattern. 3. Select the ILS button from the Main menu to launch the ILS screen. Select Automatic ILS to automatically apply the per channel settings. FIGURE 2-10 INTELLIGENT LENS SYSTEM To edit active channel ILS settings: 1. Ensure Automatic ILS is checked. 2.
Section 2: Basic Operation 2.12 CHANNEL: 3D CONTROL A single projector can display 3D images, as described below. Such images require a 3D-capable source, as well as additional hardware and cabling in order to be displayed and interpreted correctly in a typical stereo 3D viewing environment.
Section 2: Basic Operation Custom 3D sync output cable (GPIO) - available from RealD: • For routing the projector’s output sync to your sync output device (connect from the projector’s GPIO to the emitter or polarizer). NOTE: The GPIO connector can be accessed from the right-side of the projector. Power supply for your sync output device, typically wired with the custom GPIO cable. Proper 3D configuration defined in the Channel: 3D Control menu. Use an internal test pattern for best results. 2.
Section 2: Basic Operation 2.13 ADMIN MENU The 7 Admin menus offer a broad range of options used primarily for defining how the projector will respond to incoming sources in the given environment, or for adjusting a major system parameter affecting overall performance. 2.13.1 Admin: Source Menu Incoming sources can vary in their current resolution and original aspect ratio.
Section 2: Basic Operation Summary of Admin: Source Menu Options • Resolution: Record the XY resolution of the incoming signal, such as 2048 (X) and 1080 (Y), or 1920 (X) and 1080 (Y). Resolution must match the incoming signal format (assuming all of it is to be displayed) and may differ from the original resolution to recover. • To capture/process all of the incoming data, enter the full resolution of the incoming source material or leave at 0 (default).
Section 2: Basic Operation 2.13.2 Admin: Screen Menu The Admin: Screen menu defines what portion of the projector’s display panel to use and what cropping is needed to disguise possible keystoning or other geometric aberrations. Once saved, a screen file can be used with any incoming source as desired—screen data is not included in a PCF and is independent of source settings. Consider screen files as convenient compensations for physical limitations in the environment.
Section 2: Basic Operation or right cropping point in the Screen menu and change the coordinates to crop or “bring in” the corner(s) of the image slightly—either enter the specific coordinates, or adjust with slidebars. NOTE: This is cropping, not electronic keystone adjustment. In Figure 2-14, cropping simply corrects a display that overlaps the available screen.
Section 2: Basic Operation 2.13.3 Admin: MCGD Menu The Admin: MCGD menu allows users to record measurements for currently projected “uncorrected” colors. Recording the projector’s uncorrected color performance is typically completed as a final step—like a calibration—after installation. For this one-time procedure, the installer measures initial “native” (i.e., uncorrected) colors at the screen, enters the data as Measured Color Gamut Data and typically saves an MCGD file called OnSite.
Section 2: Basic Operation display to full-field red and measure coordinates at the screen. Repeat for each color and record them in the nearby XY text boxes. After all colors have been measured and recorded, select Pattern Off to leave the special test pattern mode. To cancel changes and return to the previous MCGD coordinates, leave the menu without saving.
Section 2: Basic Operation 2.13.4 Admin: TCGD Menu The Admin: TCGD menu allows users to modify or create custom Target Color Gamut Data (TCGD) files for new color gamut performance and set how closely to match the target white.
Section 2: Basic Operation • Gain: Gain indicates the luminance (a.k.a. brightness or intensity) of each color as compared to fullon white, ranging from 0 (0%) to 2 (100%). You may want to modify 1 or more gain values to precisely match color levels in other adjacent displays or to accommodate a studio’s internal color management technique. Gain would rarely, if ever, be adjusted for theatre use.
Section 2: Basic Operation 2.13.5 Admin: Lamp Menu From the Admin: Lamp menu, installers can record minimum and maximum footlambert (fL) readings to define a range from which other lamp readings are interrpolated.
Section 2: Basic Operation 2.14 WORKING WITH THE LAMP Simple software controls and adjustments can help to optimize lamp performance and ensure the brightest, most uniform image possible for the life of the lamp. These controls are located in the Advanced: Lamp and Admin: Lamp menus. 2.14.1 Turning the Lamp ON or OFF Using Web User Interface Lamp ON From the Main menu, enable Power On, Lamp On and Douser Open. Wait several minutes for the lamp to turn ON. (Figure 219) Lamp OFF 1. Disable Lamp On.
Section 2: Basic Operation 2.14.2 Adjusting Lamp Power (LiteLOC™ or Manually) There are 2 different lamp modes for general operation—maintain either a specific brightness level (LiteLOC) or a specific lamp power level. NOTES: 1) Requires Advanced user rights. 2) Keep in mind the formula: Current (Amperes) x Voltage (Volts) = Lamp Power (Watts). 3) Adjust LiteLOC™ before or after adjustment of lamp position.
Section 2: Basic Operation Adjusting Lamp Position (LampLOC™) Align a newly-installed lamp as soon as possible to ensure optimized lamp performance and peak brightness at the screen for the life of the lamp. NOTES: 1) Before adjusting, a 10-minute warm-up is recommended. 2) You can adjust lamp position either before or after adjustment of Lamp Power or LiteLOC.
Section 2: Basic Operation 2.15 CINEMA OPERATION Please read through these pages before displaying cinema for the first time. This section explains how trained operators can use the projector for presenting cinema events, such as first-run movies stored on a digital media storage device. A good understanding of all cinema functions and how to access them helps to run an event smoothly and easily.
Section 2: Basic Operation 2.16 NON-CINEMA OPERATION This section explains how to display alternative content originating from standard definition or high definition non-cinema sources, such as a PC or other graphics devices. Connect the non-cinema DVI-D source to the DVI D-A, DVI D-B ports. Each DVI-D port accepts and auto-detects progressive scan, digital RGB sources (Table 2.5), displaying them in their original incoming format.
3 Installation & Setup WARNING All installation procedures must be performed by a qualified technician in a restricted access location. WARNING When transporting the projector from a cold environment it is essential that the projector acclimatize for a minimum of 3 hours before powering up. Failure to comply could damage projector electronics. This also applies to the lamp, which will be damaged if it is powered ON when below room temperature. Store lamp between 25-65°C (77-149°F).
Section 3: Installation & Setup 3.1 POSITION THE PROJECTOR WARNING 2 people are required to safely lift and position the projector. CAUTION Auto LampLOC™ must be run any time the projector is physically moved or when it has been levelled. 1. Ensure the projector at an appropriate throw distance (projector-to-screen distance) and vertical position. Ideally, center the projector with the theatre screen.
Section 3: Installation & Setup 3.3 (OPTIONAL) MOUNT THE CONTROL DISPLAY PANEL The Control Display Panel (CDP) is shipped separately and must be connected and installed onto the rear door using the existing mounting holes. For convenience, the display angle of the CDP can easily be modified for improved viewing or it can be removed and permanently mounted in another location within the projection room. NOTE: The CDP is not recommended for use as a handheld remote.
Section 3: Installation & Setup 3.4 (OPTIONAL) CONNECT EXHAUST DUCTING If the room in which the projector is installed is not equipped to ventilate up to 11,000 BTU (per hour) the duct (119-103105-xx) must be installed to exhaust the constant stream of warm air from the projector to the outside of the building. Connect pre-installed outsideventing ductwork via the 8” inside diameter fireproof ducting material attached to the top exit port of the projector.
Section 3: Installation & Setup 3.5 (OPTIONAL) CP2000-M MOTORIZED AUXILIARY LENS MOUNT (M-MALM) INSTALLATION The M-MALM assembly is used to switch from flat to “scope” formats. This assembly can be secured to the projector base and supports either a 1.25x anamorphic lens or a 1.26x wide converter lens (WCL). The drive and control electronics package communicates with and is controlled by the projector over a 9-pin subminiature D cable that connects to the User I/O panel.
Section 3: Installation & Setup 3.6 INSTALL LENS(ES) CAUTION The lens seals the projector, preventing contamination of the main front electronics. It is important that a projector never be operated without a lens installed. 3.6.1 Primary Zoom Lens Installation 1. Turn the lens clamp to the OPEN position (Figure 3-5). 2. If present, remove the 2 hex screws from the lens mount (Figure 3-6). 3. Orient the lens so the lens retaining ring mounts line up with the lens mount. 4.
Section 3: Installation & Setup 3.7 INSTALL LAMP NOTICE: The lamp does not come installed in CP2000-M/MR projectors (119-001101-02 or higher, 119-002103-02 or higher). DANGER Only personnel trained specifically by Christie on lamp replacement and lamp safety may handle the lamp. High-pressure lamp may explode if improperly handled. Always wear Christie approved protective safety clothing whenever internal lamp door is open or while handling the lamp.
Section 3: Installation & Setup 3.8 CONNECT SOURCES AND INITIAL POWER UP Although an image is not required at this time, it is recommended external cinema servers and sources be connected. Refer to 3.9 Connecting Sources. Before igniting the lamp for the first time, it is essential the following steps are completed to ensure successful communication with the projector: 1. Assign the projector with a unique IP address.
Section 3: Installation & Setup 3.9 CONNECTING SOURCES 3.9.1 Cinema Servers WARNING Only the M-MALM and any type of automation equipment should be connected to the M-MALM or SCCI connectors on the faceplate. DO NOT connect a laptop or PC to these connectors - damage will occur. Cinema servers, such as PCs reside outside the projector and are connected to 1 of the ports on the Projector Control Module (PCM) interface panel (Figure 3-7).
Section 3: Installation & Setup 3.9.2 Connecting for Communications WARNING The “RS232” A port, located on the front User I/O panel connects to the DLP electronics and is meant for diagnostic purposes only. DO NOT connect other devices here. Many communications with the projector are initiated from the CDP controller. Depending on the installation you may require other serial and/or Ethernet links to the CP2000-M/MR.
Section 3: Installation & Setup 3.10 ADJUSTING TILT AND LEVELING CAUTION Disconnect from AC for these initial alignments. Images are not yet needed. For an ideal installation, the lens surface should be centered and parallel to the screen - this orientation helps to ensure optimized lens performance with minimal offset. Choose a sturdy mounting surface.
Section 3: Installation & Setup 3.11 BASIC IMAGE ALIGNMENT Only perform image alignment once the projector is fully assembled and powered up in its final location. Basic image alignment ensures the image reflected from the DMDs is parallel to and wellcentered with the lens and screen. This initial optical alignment is the foundation for optimizing images on the screen and must be completed before final boresight adjustments.
Section 3: Installation & Setup 3.12.1 Adjust Offset Project an image with the primary lens only. The optional auxiliary lens mount, if present, can be mounted, but moved aside by loosening the 4 bolts on the front cover and sliding the assembly out of the way. From the CDP access the Lens Control>Lens Adjustment menu to adjust horizontal and vertical offset, as necessary to display a square image on screen with minimal projector aiming error. Always adjust offset before boresight.
Section 3: Installation & Setup 5. Adjust both left and right horizontal adjusters by half the number of turns, in the opposite direction of the vertical adjust (Figure 3-13). For example, if the vertical adjust capscrews was turned 1/8 of a turn, the left and right horizontal capscrews should be turned 1/16 of a turn in the opposite direction. 6. Check the screen. If the projected image is worse than before the adjustment was made turn the vertical adjust capscrew 1/8 of turn clockwise.
Section 3: Installation & Setup 4. Use the 5mm Allen™ key to turn the right adjust capscrew (Figure 3-13, A) 1/16 of a turn clockwise. 5. Adjust the left adjust capscrew equally in the opposite direction (Figure 3-13, D). 6. Check the screen. If the projected image is worse than before the adjustment was made turn the right adjust capscrew 1/16 of turn counter-clockwise. Ensure the left adjuster is adjusted equally in the opposite direction. 7. Check the screen each time an adjustment is made.
3.13 ADJUSTABLE FOLD MIRROR & CONVERGENCE ADJUSTMENTS DANGER UV Exposure - Protective UV glasses must be worn when performing convergence adjustments. In rare instances, shipping and handling may affect the precise factory alignments of 1 or more optical components - as a final step in the installation, the installer may have to adjust the fold mirror and/or convergence of the DMDs, as described in this subsection. 3.13.
4 4.1 Maintenance LAMP REPLACEMENT DANGER Lamp replacement must be performed by Christie trained personnel only. EXPLOSION HAZARD! Wear authorized Christie approved protective clothing (P/N: 58-8900-095) whenever the lamp door is open and when handling the lamp. Never apply a twisting or bending force to the quartz lamp body. Use the correct wattage lamp supplied by Christie. Ensure those within the facility of the projector are also wearing protective safety clothing.
Section 4: Maintenance 6. Hold the lamp from the anode end and carefully slide out ensuring not to make contact with the reflector. With your free hand guide the cathode end out of the reflector, on an angle.Before WARNING Handle box with extreme caution – the lamp is hazardous even when packaged. Dispose of lamp box according to local area safety regulations. placing the old lamp into its protective case ensure the cathode nut is reinstalled.
Section 4: Maintenance 13. Close the rear access door. NOTE: Ensure the hex key is placed back into its holder before closing the rear access door. 14. Record the serial number of the new lamp. a. b. c. d. Plug in the projector and power it up. In the Lamp menu, select Change Lamp. In the Lamp S/N text box, enter the serial number. Press Enter to record the number and to reset the lamp timer. The timer begins to log time for the new lamp. 15. Ensure LampLOC™ is adjusted. 4.
Section 4: Maintenance 4.3 LENS REPLACEMENT 4.3.1 REMOVE LENS 1. Power down the projector. Allow the fans to cool the lamp before unplugging the projector. If necessary, a lens can be swapped out while the projector is running, but this can result in dust being drawn into the projector. Avoid if possible. FIGURE 4-3 LENS ASSEMBLY 2. Install the lens cap (Figure 4-4, 1) and release the lens clamp by pushing it up (Figure 4-4, 2). FIGURE 4-4 RELEASE LENS CLAMP 3.
Section 4: Maintenance 4.3.2 INSTALL LENS 1. Remove the small rear cap. 2. Align the mounts on the lens connector with the lens mount. Insert the lens until it connects with the magnets on the mount. Once the lens makes contact with the magnetic plates it will be seated correctly and the connector for motorized zoom and focus will be properly connected (Figure 4-5). 3. For added stability, secure the capscrews provided on the lens-mount.
5 Troubleshooting 5.1 POWER 5.1.1 Projector Does Not Power ON 1. Check the AC receptacle switch. If it is in the A+B position there must be 2 line cords connected (1 of which is not provided) in order to operate. 2. Ensure the CDP display backlight and the LEDs are functioning. Check if the menus are displayed on the CDP. If the CDP is not functioning it may need to be replaced. 5.2 LAMP 5.2.1 Lamp Does Not Ignite 1.
Section 5: Troubleshooting 5. Increase lamp power, if possible. Lamps which are near end of life may not operate reliably at lowest power range. 6. Fold mirror misalignment (Christie service required). 5.2.4 LampLOC™ Does Not Seem to Work If the Do Auto LampLOC™ function does not work, try adjusting the lamp position manually, via the LampLoc>Manual Adjust menu. Observe screen brightness by adjusting the XYZ values or use a light meter to check for changes in brightness.
Section 5: Troubleshooting 5.3.3 Image Appears Vertically Stretched or ‘Squeezed’ into Center of Screen Source data converted from film and “pre-squeezed” for CP2000-M/MR display format may require use of an anamorphic lens (or resizing) to regain full “scope” image width and proper proportions. 5.3.4 No Image, Just Pink Snow This problem is due to link encrypted cinema content not receiving the appropriate cryptographic key information from the source cinema server. 1.
Section 5: Troubleshooting 5.4.3 The Display is Faint 1. The source may be double terminated. Ensure the source is terminated only once. 2. The source (if non-video) may need sync tip clamping. 5.4.4 The Upper Portion of the Display is Waving, Tearing or Jittering This can occur with video or VCR sources. Check your source. 5.4.5 Portions of the Display are Cut OFF or Warped to the Opposite edge Resizing may need adjustment. Adjust until entire image is visible and centered. 5.4.
Section 5: Troubleshooting 5.4.12 Display is “Noisy” 1. Display adjustment at the input source may be required. Adjust pixel tracking, phase and filter. Noise is particularly common on YPbPr signals from a DVD player. • Ensure the video input is terminated (75 ohms). If it is the last connection in a loop-through chain, the video input should be terminated at the last source input only. 2. The input signal and/or signal cables carrying the input signal may be of poor quality. 3.
6 6.1 Specifications CONTROL SIGNAL COMPATIBILITY 6.1.1 Ethernet Management Port (2) Interface 10/100 Base-T Connector Female RJ-45 Bit rate 10 Mbps/100 Mbps 6.1.2 Ethernet Auxiliary Port Interface 10 Base-T/100 Base-TX Connector Female RJ-45 Bit rate 10 Mbps/100 Mbps 6.1.3 RS232-A Port (TI Light Engine) Interface TIA-232 Connector 9-pin subminiature D, female Bit rate 38,400 bps (default) - 115,200 bps (auto-detected) 6.1.
Section 7: Specifications 6.1.6 Simple Contact Closure Interface (SCCI) Port Interface Opto-LED inputs, TTL voltage output Connector 9-pin subminiature D, male Number and type of I/O Input 1 - Lamp OFF Input 2 - Lamp ON Input 3 - Douser Open Input 4 - Douser Closed Output 1 - Lamp Indicator (high=lamp ON) 6.2 Input Current 5mA nom., 50mA max. Input Forward Voltage Drop 1.1V nom.
Section 7: Specifications 6.3 POWER REQUIREMENTS 6.3.1 Standard Mode (uses line cord provided) Voltage Range: 200 - 240 VAC Line Frequency: 50 Hz - 60 Hz nominal Inrush Current: < 85 A max. Current Consumption: 16 A max. (at 200 VAC) Power Consumption: 3200 W max. Current Rating of AC Input: IEC-320-C19/20A (required by regulatory) Line Cord Plug Type NEMA 6-20P 6.3.
Section 7: Specifications 6.5 REGULATORY This product conforms to the following regulations related to product safety, environmental requirements and electromagnetic compatibility (EMC): • FCC Part 15, Subpart B Class A; CISPR22/EN55022; CISPR24/EN55024 • UL 60950-1 First Edition; CAN/CSA-C22.2 No 60950-1-03 First edition; • IEC60950-1:2001 6.
